balanza spider

8/15/2019 Balanza Spider

1/332

IndustrialQuick ReferenceGuide

15311300A

(5/98).01


2/332

© Mettler-Toledo, Inc. 1998

No part of this manual may be reproduced or transmitted in any form or by any means,

electronic or mechanical, including photocopying and recording, for any purpose without theexpress written permission of Mettler-Toledo, Inc.

U.S. Government Restricted Rights: This documentation is furnished with Restricted Rights.


3/332

METTLER TOLEDO

Publication Revision HistoryAn overview of this manual’s revision history is compiled below.

Publication Name: Industrial Quick Reference User’s Guide

Publication Part Number: 15311300A Publication Date: 10/98

Part Number Date Revisions

15311300A 5/98 Added Chapter 39, Cougar Indicator


4/332


5/332

INTRODUCTION

Information regarding METTLER TOLEDO Technical Training may be obtained by writing, calling,or faxing to:

METTLER TOLEDO350 W. Wilson Bridge RoadWorthington, Ohio 43085

ph: (614) 438-4400fax: (614) 438-4444

WARNING

This publication is provided solely as a guide for individuals who have received technical training andis familiar with the technical manuals of the Mettler Toledo products.

This guide is not meant to replace the technical manual for various products.

Please review the specific technical manuals for detailed instructions and safety precautions beforeoperating or servicing the various Mettler Toledo products.

METTLER TOLEDO RESERVES THE RIGHT TO MAKE REFINEMENTS ORCHANGES WITHOUT NOTICE.


6/332

PRECAUTIONS

WARNINGONLY PERMIT QUALIFIED PERSONNEL TO SERVICE

THIS EQUIPMENT. EXERCISE CARE WHEN MAKINGCHECKS, TESTS AND ADJUSTMENTS THAT MUST BEMADE WITH POWER ON. FAILING TO OBSERVETHESE PRECAUTIONS CAN RESULT IN BODILY HARM.

WARNINGFOR CONTINUED PROTECTION AGAINST SHOCKHAZARD CONNECT TO PROPERLY GROUNDEDOUTLET ONLY.

DO NOT REMOVE THE GROUND PRONG.

WARNINGDISCONNECT ALL POWER TO THIS UNIT BEFOREREMOVING THE FUSE OR SERVICING.

CAUTIONBEFORE CONNECTING/DISCONNECTING ANY INTERNAL ELECTRONICCOMPONENTS OR INTERCONNECTING WIRING BETWEEN ELECTRONICEQUIPMENT ALWAYS REMOVE POWER AND WAIT AT LEAST THIRTY (30)SECONDS BEFORE ANY CONNECTIONS OR DISCONNECTIONS ARE MADE.FAILURE TO OBSERVE THESE PRECAUTIONS COULD RESULT IN DAMAGE TOOR DESTRUCTION OF THE EQUIPMENT OR BODILY HARM.

CAUTIONOBSERVE PRECAUTIONS

FOR HANDLINGELECTROSTATIC

SENSITIVE DEVICES.

READ this manual BEFORE

operating or servicing thisequipment.

FOLLOW these instructions

carefully.

SAVE this manual for futurereference.

DO NOT allow untrainedpersonnel to operate, clean,inspect, maintain, service,or tamper with this

equipment.

ALWAYS DISCONNECT thisequipment from the power

source before cleaning orperforming maintenance.

CALL METTLER TOLEDO for

parts, information, andservice.


7/332

METTLER TOLEDO

Publication Problem ReportIf you find a problem with our documentation, please complete and fax this form to (614) 438-4783

Publication Name: Industrial Quick Reference User’s Guide

Publication Part Number: 15311300A Publication Date: 5/98

PROBLEM(S) TYPE: DESCRIBE PROBLEM(S):

Technical Accuracy Text Illustration

Completeness Procedure/step Illustration Definition What information is Example Guideline Feature

missing?

Explanation

Other (please explain below)

ClarityWhat is not clear?

SequenceWhat is not in the right

order?

Other CommentsUse another sheet for

additional comments.

Your Name: Location:

Phone Number: ( )

Mettler-Toledo, Inc. Printed in U.S.A. A14981600A

Fax this completed form to MarCom at (614) 438-4783


8/332


9/332

METTLER TOLEDOScales & Systems350 West Wilson Bridge RoadWorthington, Ohio 43085-2273

P/N: 15311300A

(5/98).01

METTLER TOLEDO® is a registered trademark of Mettler-Toledo, Inc.©1998 Mettler-Toledo, Inc.

Printed in U.S.A.

15311300A


10/332

CONTENTS

1 3026/3036 Over/Under Scales ............................................................................... 1-1

Jumpers and Keyboard Functions ......................................................................................... 1-1Display PCB........................................................................................................................1-1

Power Supply PCB ............................................................................................................... 1-1Keyboard ............................................................................................................................1-1

Softswitch Settings .............................................................................................................. 1-2

Error Codes......................................................................................................................... 1-3

2 3027 Over/Under................................................................................................. 2-1Jumpers and Keyboard Functions ......................................................................................... 2-1

Display PCB........................................................................................................................2-1

Power Supply PCB ............................................................................................................... 2-1

Keyboard ............................................................................................................................2-1Softswitch Settings .............................................................................................................. 2-2

Error Codes......................................................................................................................... 2-3

3 8140 Digital Indicator .......................................................................................... 3-1Jumpers and Keyb[oard Functions ........................................................................................ 3-1


Error Codes......................................................................................................................... 3-3

4 M8141 Power Supply........................................................................................... 4-1

Jumpers and Keyboard Functions ......................................................................................... 4-1Jumpers .............................................................................................................................4-1Keyboard ............................................................................................................................4-1

Setup Chart ........................................................................................................................ 4-2

Error Codes......................................................................................................................... 4-3

5 8142 Indicator .................................................................................................... 5-1Jumpers and Keyboard Functions ......................................................................................... 5-1

Main PCB Jumpers .............................................................................................................. 5-1Dual Display PCB Jumpers ...................................................................................................5-1Rack Display PCB Jumpers...................................................................................................5-1

Optional BCD/Analog PCB.....................................................................................................5-1Keyboard Functions During Setup...........................................................................................5-2

Quick Reference Chart ......................................................................................................... 5-2

Error Codes......................................................................................................................... 5-5Operational Error Codes ........................................................................................................ 5-5

Calibration Error Codes .........................................................................................................5-6


11/332

6 8213 Checkstand Scale ....................................................................................... 6-1Jumpers Functions ..............................................................................................................6-1

Main PCB Jumpers .............................................................................................................. 6-1


Calibration.......................................................................................................................... 6-2

Required Test Weights ..........................................................................................................6-2Error Codes......................................................................................................................... 6-3

7 8505 Printer ....................................................................................................... 7-1Keyboard Functions ............................................................................................................. 7-1

Accessing the Setup Mode ................................................................................................... 7-1

Pushbutton Functions During Setup....................................................................................... 7-1

Setup Quick Reference Chart ................................................................................................ 7-2

Error Codes......................................................................................................................... 7-4

8 8510 Panel Mount Indicator ................................................................................. 8-1Jumpers and Keyboard Functions ......................................................................................... 8-1Main PCB Jumpers .............................................................................................................. 8-1Power Supply PCB ............................................................................................................... 8-1Dual Display PCB Jumpers ...................................................................................................8-1

Keyboard ............................................................................................................................8-1


Error Codes......................................................................................................................... 8-4

9 8510 Stainless Steel Indicator .............................................................................. 9-1Jumpers and Keyboard Functions ......................................................................................... 9-1

Display PCB Jumpers........................................................................................................... 9-1Power Supply PCB ............................................................................................................... 9-1

Keyboard ............................................................................................................................9-1


Error Codes......................................................................................................................... 9-4

10 8510 Wall Mount Indicator ............................................................................... 10-1Jumpers and Keyboard Functions ....................................................................................... 10-1

Display PCB Jumpers......................................................................................................... 10-1

Power Supply PCB ............................................................................................................. 10-1Keyboard ..........................................................................................................................10-1

Softswitch Settings............................................................................................................ 10-2Error Codes....................................................................................................................... 10-4


12/332

11 8511 Digital Indicator ...................................................................................... 11-1Jumpers and Keyboard Functions ....................................................................................... 11-1

Main PCB Jumpers ............................................................................................................ 11-1Power Supply PCB ............................................................................................................. 11-1

Keyboard ..........................................................................................................................11-2

Soft Switch Settings ............................................................................................................11-3Error Codes....................................................................................................................... 11-5


Main PCB Jumpers ............................................................................................................ 12-1

Programming Procedure ..................................................................................................... 12-1Keyboard Functions............................................................................................................12-2

Softswitch Settings............................................................................................................ 12-2Exiting The Setup Routine..................................................................................................12-13

Error Codes..................................................................................................................... 12-14


Main PCB Jumpers ............................................................................................................ 13-1Passive Active Analog PCB..................................................................................................13-1Keyboard ..........................................................................................................................13-1

Softswitch Settings............................................................................................................ 13-2

Error Codes....................................................................................................................... 13-5


Main PCB Jumpers ............................................................................................................ 14-1Fiber Optic PCB .................................................................................................................14-1


Error Codes....................................................................................................................... 14-5

15 8530 DigiTOL®

Indicator ................................................................................... 15-1Jumpers and Keyboard Functions ....................................................................................... 15-1

Main PCB Jumpers ............................................................................................................ 15-1Keyboard ..........................................................................................................................15-1


Error Codes....................................................................................................................... 15-6

16 8530VS DigiTOL®

Indicator ............................................................................... 16-1Jumpers and Keyboard Functions ....................................................................................... 16-1



Error Codes....................................................................................................................... 16-6


13/332

17 8571 High Resolution Counting Scale................................................................ 17-1Jumpers and Keyboard Functions ....................................................................................... 17-1



Error Codes....................................................................................................................... 17-3

18 8572 Counting Scale ....................................................................................... 18-1Keyboard Functions ........................................................................................................... 18-1


Error Codes....................................................................................................................... 18-5

19 8581 Counting Scale ....................................................................................... 19-1Jumpers and Keyboard Functions ....................................................................................... 19-1

Main PCB Jumpers ............................................................................................................ 19-1

Display PCB......................................................................................................................19-1Keyboard ..........................................................................................................................19-1


Error Codes....................................................................................................................... 19-4

20 8582 High Resolution Counting Scale................................................................ 20-1Jumpers and Keyboard Functions ....................................................................................... 20-1

Main PCB Jumpers ............................................................................................................ 20-1

Analog Scale PCB .............................................................................................................. 20-1Digital Scale PCB...............................................................................................................20-1


Error Codes....................................................................................................................... 20-4

21 8617 Scoreboard............................................................................................. 21-1Jumpers and Switch Settings.............................................................................................. 21-1

Main PCB Jumpers ............................................................................................................ 21-1Hardswitch Descriptions ..................................................................................................... 21-2

Select Scoreboard Operation Switch S3......................................................................21-2Scoreboard Operation Selection ................................................................................21-2

Scoreboard Setup Switch S4 ....................................................................................21-2Multidrop Address Selection .....................................................................................21-2

Softswitch Settings............................................................................................................ 21-3Simple ASCII Mode............................................................................................................. 21-4

MULTI-SCALE MODE........................................................................................................... 21-4[F1 2]............................................................................................................................ 21-4

Error Codes....................................................................................................................... 21-5


14/332

22 8623 Scoreboard............................................................................................. 22-1Jumpers........................................................................................................................... 22-1

Displayed Data (Weight) Configuration Jumper Connections....................................................22-1Input Control Wiring ...........................................................................................................22-1

Data I/O Wiring..................................................................................................................22-2

Dip Switches..................................................................................................................... 22-2Error Codes....................................................................................................................... 22-3

23 8624 Scoreboard............................................................................................. 23-1Jumpers........................................................................................................................... 23-1

Displayed Data Jumpers ..................................................................................................... 23-1

Input Control Jumpers ........................................................................................................ 23-2

Switch Settings ................................................................................................................. 23-3

Error Codes....................................................................................................................... 23-3

24 8682 Scale ..................................................................................................... 24-1Keyboard Functions ........................................................................................................... 24-1


Error Codes....................................................................................................................... 24-3

25 8806 Printer ................................................................................................... 25-1Jumpers and Keyboard Functions ....................................................................................... 25-1

Jumpers - All Versions........................................................................................................ 25-1

Keyboard ..........................................................................................................................25-1

Switch Settings ................................................................................................................. 25-2

Dip Switches..................................................................................................................... 25-2

Error Codes....................................................................................................................... 25-4

26 8807 Printer ................................................................................................... 26-1Keyboard Functions ........................................................................................................... 26-1

LED Displays..................................................................................................................... 26-1

Self Test Mode ...................................................................................................................26-1

Switch Settings ................................................................................................................. 26-2

Error Codes....................................................................................................................... 26-2

27 8844 Printer ................................................................................................... 27-1Jumpers ...........................................................................................................................27-1

Dip Switches..................................................................................................................... 27-1Baud Rate Selections.......................................................................................................... 27-2Switch Bank 2 Settings ....................................................................................................... 27-2

Troubleshooting ................................................................................................................ 27-3

Self Tests ......................................................................................................................... 27-4Test 1............................................................................................................................... 27-4

Test 2 and 3 .....................................................................................................................27-4


15/332

28 8845 Printer ................................................................................................... 28-1Dip Switches..................................................................................................................... 28-1

Baud Rate Selections.......................................................................................................... 28-1Switch Bank 2 Settings ....................................................................................................... 28-2

29 8856 Strip Printer ............................................................................................ 29-1Keyboard Functions ........................................................................................................... 29-1

Self Test Mode .................................................................................................................. 29-1

Hex Dump Mode ............................................................................................................... 29-1

Programming Switches ...................................................................................................... 29-2

International Character Set Selection:.................................................................................. 29-2

(shaded areas represent default settings) .............................................................................. 29-2Communication Parameters ............................................................................................... 29-3

Word Length (Data Bits) ..................................................................................................... 29-3

Parity Bit Selection .............................................................................................................29-3Baud Rate Selection ...........................................................................................................29-3

Error Codes....................................................................................................................... 29-4

30 8860 Printer ................................................................................................... 30-1Dip Switches..................................................................................................................... 30-1

Logic PCB Jumper Selections ..............................................................................................30-1

[SW1-1]:Data Input Mode Select.............................................................................. 30-2[SW1-6], [SW1-7], [SW1-8]:Label Format (Mode II Operation Only)...........................30-2[SW2-1]: Character Output Enable (Mode I) or Expanded Print Size (Mode II)........ 30-2

[SW2-1]: Character Enable (Mode I Operation [SW1-1 On]) ...............................30-3[SW2-1]:Expanded Print Size (Mode I Operation [SW1-1 Off]......................................30-3[SW2-2], [SW2-3] and [SW2-4]Preferred Line Selection ............................................ 30-3

[SW2-5], [SW2-6]:Bar Code Format........................................................................ 30-3[SW2-7]:Checksum Enable[SW2-8]:Baud Rate Select ................................................ 30-3

Self Test ........................................................................................................................... 30-4Bar Code Test Label ........................................................................................................... 30-4Logic PCB Switch Settings Test ............................................................................................30-4

Error Codes....................................................................................................................... 30-4

31 8861 Printer ................................................................................................... 31-1Softswitch Settings............................................................................................................ 31-1

Error Codes....................................................................................................................... 31-8

32 BC/SC Counting Scales...................................................................................... 32-1Loading Master Mode Defaults ........................................................................................... 32-1

Keyboard Functions for Master Mode................................................................................... 32-1


16/332

33 Jaguar............................................................................................................ 33-1Keyboard Functions ........................................................................................................... 33-1

Jumpers and Switch Settings Controller............................................................................... 33-2 Analog .............................................................................................................................33-3

Allen-Bradley PCB..............................................................................................................33-3

POWERCELL I/O PCB.......................................................................................................... 33-3MMR (IDNET) I/F PCB......................................................................................................... 33-3Multifunction I/O PCB..........................................................................................................33-4

Scale Interface Program Block............................................................................................ 33-4Market Sub-block...............................................................................................................33-4Scale Type Sub-block ......................................................................................................... 33-4Calibration Unit Sub-block ................................................................................................... 33-6

Capacity Sub-block ............................................................................................................ 33-7Increment Size Sub-block.................................................................................................... 33-7Shift Adjustment Sub-block.................................................................................................. 33-8Linearity Correction Sub-block.............................................................................................33-8

Calibration Sub-block ......................................................................................................... 33-9Without Linearity Correction .....................................................................................33-9With Linearity Correction Enabled..............................................................................33-9

Zero Adjustment Sub-block ................................................................................................ 33-10Span Adjustment Sub-block............................................................................................... 33-10Gravity Adjustment Sub-block...............................................................................................33-10Reset to Factory Sub-Block................................................................................................ 33-11

Service Mode for .............................................................................................................. 33-11MMR (IDNET) Bases ........................................................................................................ 33-11RESET program Sub-block ................................................................................................33-12

SCALE PARAMETERS program Sub-block............................................................................. 33-12LINEARITY program Sub-block ..........................................................................................33-13

CALIBRATION program Sub-block.......................................................................................33-13SAVE PARAMETERS program Sub-block ..............................................................................33-14

RETURN program Sub-block................................................................................................ 33-14

Application Environment Program Block............................................................................. 33-14Character Set Sub-block.................................................................................................... 33-14Language Sub-block ........................................................................................................ 33-15

Keyboard Type Sub-block ................................................................................................. 33-15Scale ID Sub-block........................................................................................................... 33-15Time and Date Sub-block..................................................................................................33-16

Alternate Weight Units Sub-block........................................................................................33-17

Power Up Operation Sub-block .........................................................................................33-19Tare Operation Sub-block..................................................................................................33-19Zero Operation Sub-block..................................................................................................33-21Zero Operation Sub-block for MMR (IDNET) Bases................................................................33-22

Stability Detect Sub-block ..................................................................................................33-23Stability Detect Sub-block for MMR (IDNET) Bases................................................................33-23Beeper Operation Sub-block ................................................................................................ 33-24

Application Type Sub-block ...............................................................................................33-24 Vibration Rejection Sub-block ............................................................................................ 33-25 Vibration Rejection Sub-block for MMR (IDNET) Bases ..........................................................33-26

Serial Interface Program Block.......................................................................................... 33-27


17/332

Configure Port Sub-block ..................................................................................................33-27Local .................................................................................................................. 33-28Remote ............................................................................................................... 33-29

Add a Connection ................................................................................................. 33-29

Delete a Connection.............................................................................................. 33-33Configure Template Sub-block .......................................................................................... 33-33

Clear Template ..................................................................................................... 33-34Copy Template ..................................................................................................... 33-34

Edit Template ....................................................................................................... 33-34

Configure Discrete Program Block..................................................................................... 33-37Discrete Inputs Sub-block.................................................................................................. 33-38Discrete Outputs Sub-block................................................................................................33-39

Assign Setpoints Sub-block ................................................................................................ 33-41Configure Memory Program Block ......................................................................................33-41Configure Literals Sub-block ................................................................................................ 33-42Configure Prompts Sub-block ........................................................................................... 33-42

Configure Consecutive Numbering Sub-block.......................................................................33-44

Configure JagBASIC Program Block .................................................................................. 33-44Password Sub-block ........................................................................................................ 33-44Keyboard Sub-block ......................................................................................................... 33-45

Display Sub-block............................................................................................................ 33-45 Auto Start Sub-block ......................................................................................................... 33-46Manual Start Sub-block..................................................................................................... 33-46

Send RAM Files Sub-block.................................................................................................33-46Initialize RAM Disk Sub-block ........................................................................................... 33-47Password Maintenance Sub-block...................................................................................... 33-47

Configure Network Program Block..................................................................................... 33-48Network Keyboard/ Display Sub-block ................................................................................33-48

PC Data Sub-block........................................................................................................... 33-48PLC SP Control Sub-block ................................................................................................. 33-49Diagnostics and Maintenance Program Block ......................................................................... 33-49

Memory Test Sub-block .................................................................................................... 33-49Display Test Sub-block .....................................................................................................33-50Keyboard Test Sub-block ..................................................................................................33-50Scale Test Sub-block ........................................................................................................ 33-50

MMR (IDNET) Scale Bases .................................................................................... 33-51DigiTOL J-Box or Power Cell Bases.........................................................................33-51

Serial Test Sub-block ........................................................................................................ 33-55

Parallel I/O Test Sub-block ................................................................................................33-57PAR 1 or PAR 3 (Discrete Input).............................................................................33-57

PAR 2 or PAR 4 (Discrete Output)........................................................................... 33-57Network Test Sub-block ....................................................................................................33-58

Send BRAM to Jag Sub-block ...........................................................................................33-58Print Setup Sub-block ....................................................................................................... 33-59Reset to Factory Sub-block ................................................................................................ 33-59

Options Program Block .................................................................................................... 33-60

Error Codes and Actions................................................................................................... 33-61

34 Lynx ............................................................................................................... 34-1


18/332

Jumper and Keyboard Functions......................................................................................... 34-1Keyboard Functions............................................................................................................34-1Controller PCB ...................................................................................................................34-2Soft Switch Settings ............................................................................................................34-2

Scale Interface Program Block............................................................................................ 34-3

Market Sub-block...............................................................................................................34-3Scale Type Sub-block ......................................................................................................... 34-3Calibration Unit Sub-block ................................................................................................... 34-4Capacity Sub-block ............................................................................................................ 34-4

Increment Size Sub-block.................................................................................................... 34-5Shift Adjust Sub-block.........................................................................................................34-5Linearity Correction Sub-block.............................................................................................34-6

Calibration Sub-block ......................................................................................................... 34-6Without Linearity Correction .....................................................................................34-6With Linearity Correction Enabled..............................................................................34-7

Zero Adjustment Sub-block .................................................................................................. 34-7

Span Adjustment Sub-block.................................................................................................. 34-8

Gravity Adjustment Sub-block .............................................................................................34-8Character Set Sub-block...................................................................................................... 34-9Time and Date Sub-block....................................................................................................34-9

Weight Units Sub-block..................................................................................................... 34-10Power up Operation Sub-block........................................................................................... 34-11Tare Operation Sub-block..................................................................................................34-11

Zero Operation Sub-block..................................................................................................34-13Stability Detection Sub-block................................................................................................ 34-15

Vibration Rejection Sub-block ............................................................................................ 34-15Port Configure Sub-block ..................................................................................................34-17

Connection .......................................................................................................... 34-19Configure Template Sub-block ...........................................................................................34-22

Clear Template ..................................................................................................... 34-22

Copy Template ..................................................................................................... 34-23Edit Template ....................................................................................................... 34-23

Configure Printer Control Sub-block ....................................................................................34-27Configure Inputs Sub-block................................................................................................34-28

Configure Outputs Sub-block ............................................................................................34-28Configure Literals Sub-block ................................................................................................ 34-30Configure Prompts Sub-block ............................................................................................ 34-30Configure Consecutive Numbering Sub-block.......................................................................34-32

Analog Output Sub-block .................................................................................................. 34-32BCD Output Sub-block ......................................................................................................34-33

Accumulate Sub-block ...................................................................................................... 34-33ID/Tare Sub-block ............................................................................................................ 34-34Password Sub-block ........................................................................................................ 34-36Dynamic Sub-block.......................................................................................................... 34-37Memory Test Sub-block .................................................................................................... 34-37

Display Test Sub-block .....................................................................................................34-37Keyboard Test Sub-block ..................................................................................................34-38Scale Test Sub-block ........................................................................................................ 34-38

Serial I/O Test Sub-block...................................................................................................34-39Discrete I/O Test Sub-block................................................................................................34-40


19/332

Discrete Input.......................................................................................................34-40Discrete Output..................................................................................................... 34-41

Print Setup Sub-block ....................................................................................................... 34-41Reset to Factory Sub-block ................................................................................................ 34-42

Error Codes..................................................................................................................... 34-43

35 Panther .......................................................................................................... 35-1Jumpers and Switch Settings.............................................................................................. 35-1

Controller PCB ...................................................................................................................35-1Keyboard Functions............................................................................................................35-2

Program Block Access ....................................................................................................... 35-3

General Programming Procedure ........................................................................................ 35-3


Error Codes....................................................................................................................... 35-8

36 Spider............................................................................................................. 36-1

Single Load Cell Connections ............................................................................................. 36-1Table of Scale Base Parameters ...........................................................................................36-3Servicemode Configuration.................................................................................................. 36-4

Accessing Service Mode......................................................................................................36-4

Navigating in Servicemode .................................................................................................. 36-5Unit Program Block ............................................................................................................ 36-5Ramp Program Block ......................................................................................................... 36-6

Serial Number Program Block.............................................................................................. 36-6Weighing Cell Program Block .............................................................................................. 36-6

Approval Sub-block ............................................................................................................ 36-7Capacity Sub-block ............................................................................................................ 36-7

Range Program Block.........................................................................................................36-8Resolution Program Block................................................................................................... 36-8

Calibration Program Block.................................................................................................. 36-9Geo Sub-block................................................................................................................... 36-9

Geo Mode ............................................................................................................. 36-9Cal Exe Sub-block............................................................................................................ 36-10Factory Reset Program Block ............................................................................................. 36-10List Program Block........................................................................................................... 36-11

Return Program Block....................................................................................................... 36-11Mastermode Configuration................................................................................................. 36-11

Accessing Mastermode ..................................................................................................... 36-12

Mastermode Entry ............................................................................................................ 36-12

Navigating in Mastermode................................................................................................. 36-12Function Program Block.................................................................................................... 36-13

Auto Zero Correction Program Block ................................................................................... 36-14

Auto Tare Program Block .................................................................................................. 36-14 Automatic Shutdown Program Block ...................................................................................36-15Power-Up (Save) Program Block ....................................................................................... 36-15

Vibration Adapter Program Block........................................................................................36-16Process Adapter Program Block .........................................................................................36-16Interface 1 Program Block................................................................................................. 36-17Reset Interface to Factory .................................................................................................. 36-17


20/332

Communication ............................................................................................................... 36-18Parameters Sub-block ...................................................................................................... 36-18Operating Mode Sub-block ................................................................................................36-19Data Definition Sub-block.................................................................................................. 36-20

Define Print Format Sub-block............................................................................................ 36-20Exit Interface 1 Sub-block.................................................................................................. 36-21Interface 2 Program Block (Optional)..................................................................................36-21

Accuracy Control Program Block ........................................................................................36-21

List Program Block........................................................................................................... 36-22Restricting Access to Mastermode ......................................................................................36-22

Access to Mastermode with Restricted Entry .........................................................................36-22

Reset to Factory Program Block .........................................................................................36-23Error Codes and Descriptions ............................................................................................36-24

37 TrimWeigh ...................................................................................................... 37-1Jumpers and Keyboard Functions ....................................................................................... 37-1

Display PCB Jumpers......................................................................................................... 37-1

Power Supply PCB Jumpers.................................................................................................. 37-1Keyboard Functions During Setup.........................................................................................37-1

Switch Settings ................................................................................................................. 37-2

Error Codes....................................................................................................................... 37-4

38 XX38 .............................................................................................................. 38-1Softswitch Functions.......................................................................................................... 38-1

Error Codes....................................................................................................................... 38-5

39 Cougar Industrial Terminal................................................................................ 39-1

Jumpers and Keyboard Functions ....................................................................................... 39-1Main PCB Jumpers ............................................................................................................ 39-1Keyboard ..........................................................................................................................39-1

Softswitch Settings for Cougar Standard Software................................................................. 39-2

Softswitch Settings for Cougar VS Software.......................................................................... 39-6

Error Codes..................................................................................................................... 39-10


21/332


22/332

Chapter 1: 3026/3036 Over/Under ScalesJumpers and Keyboard Functions

(1/98) 1-1

1 3026/3036 Over/Under Scales

Jumpers and Keyboard

Functions

Display PCBW1 - Decimal Point, comma display

Out = decimal pt.; In = comma

W2 - ROM Select

Must short (1-2)

W3 - ROM Enable

Must be in

Power Supply PCBW1 - Setup Entry

In = enable; Out = disable

W2 - Internal Suppresser (Use with TTL outputs)

In = connect suppresser; Out = disconnect

KeyboardKey Setup Function Normal Function

ZERO Back Up to Prev. Step Re-Zero Scale

TARE/TARGET Toggle Selections Enter Target or Tare

CLEAR Advance to [CALOFF] Clear Tare or Target Wgt

UNITS N/A Toggle Units (Lb/Kg)

PRINT Accept Selection Initiate a Print Command


23/332

METTLER TOLEDO Industrial Quick Reference User’s Guide

(1/98)1-2

Softswitch Settings

F0-Span Adjust 1-Enable; 0-Disable

F1-Operating Mode0 = NA; = 3026; 2 = NA; 3 = 3036; 4 = NA;

F1.5- Indicator Mode0 = indicator; 1 = over/under

F2-Calibration Units0 = LB; 1 = KG; 2 = lb-oz; 3 = oz; 4 = g;

F3-Units Key 1-Enable; 0-Disable

F4-Weight/LED Enable0 = wgt on, led off; 1 = wgt on, led on;

F4.1-Zone Width Entry

0 = Increments; 1 = % of target;F5-Zero Cursor /%Target

1-Enable; 0-DisableF6-Auto Zero Maint.

0 = disable; 1 = .5inc; 2 = 1inc; 3 = 3 inc.F6.1AZM in Net Mode

0 = gross; 1 = gross and net F7-Zero Key Enable

0 = disable; 1 = 2%; 2 = 20%; 3 =20%GandNet

F8-Motion Sensitivity

0 = 1d; 1 = 3d;

F9-Filter Selection0 = disable; 1 = light; 2 = medium; 3 = heavy

9.1-Dig. Load Cell Filter

1-Enable; 0-DisableF10-Expanded Weight

1-Enable; 0-Disable

F11-Net Wgt. Display0 = gross wgt; 1 = net diff.

F12-Zone ProgrammingPrint = enter; Tar e = skip

12.1-Setup Entry Point 0 = F0; 1 = F12

12.2-High Zone WidthTare = toggle; Print = Select

12.3-High Accept WidthTare = toggle; Print = Select

12.4-Low Accept WidthTare = toggle; Print = Select

12.5-Low Zone WidthTare = toggle; Print = Select

12.6-Stored Tare Wgts.1-Enable; 0-Disable

F13-Tare Enable1-Enable; 0-Disable; 2 = auto tare

F14-Auto Clear Tare

1-Enable; 0-DisableF15-Serial Port Program.

Print = enter; Tare = skip15.1-Format

0 = cont. ;1 = demand15.2-Baud Rate

Tare = toggle; Print = Select 15.3-Parity

0 = always 0; 1 = odd; 2 = even15.4-Checksum

1-Enable; 0-Disable

15.5-Line Format Select 0 = single line displayed; 1 = GTN single line;2 = GTN multiple line;

15.6-Double Wide Print

1-Enable; 0-Disable

15.7-Auto Print 1-Enable; 0-Disable

15.8-Print Wgt. Class1-Enable; 0-Disable

15.9-Stop Bits0 = 1; 1 = 2;

F16-ASCII Input 1-Enable; 0-Disable

F18-Tare Interlocks1-Enable; 0-Disable

F19-Motion Blanking1-Enable; 0-Disable

F20-TTL Input 0 = print; 1 = tare; 2 = zero; 3 = unit selection

CAL-CalibrationPrint = enter; Tare = skip


24/332

Chapter 1: 3026/3036 Over/Under ScalesError Codes

(1/98) 1-3

Error Codes

Error Code Description Suggested Corrective Action

E1 Program Memory Fatal 1. Check DC Supply Voltages2. Replace Display PCB

E2 Internal Ram MemoryFatal Error

1. Check DC Supply Voltages2. Replace Display PCB

E3 NOVRAM Memory Error 1. Check DC Supply Voltages2. Reprogram, Recalibrate3. Replace Display PCB

E8 Communication Loss With DLC 1. Check DC Supply Voltages2. Check Interconnect Harnesses for Load Cell and PCB’s3. Replace Load Cell4. Replace Display PCB

E9 DLC Out of Range, Under Capacity 1. Check For Mechanical Bind2. Check DC Supply Voltages3. Replace Load Cell

4. Replace Display PCB

E10 DLC Memory Verify Fatal Error 1. Check DC Supply Voltages

2. Replace Load Cell

E11 DLC ROM Error 1. Check DC Supply Voltages2. Replace Load Cell

E13 DLC EPROM Error 1. Check DC Supply Voltages2. Recalibrate Scale


E16 Math Error 1. Press Clear Key To Clear Error, Check Program and Recalibrate

E32 Insufficient Test Used for Calibration 1. Recalibrate With At Least 50% of Programmed Scale CapacityE34 Test Weight Over Cap 1. Check Capacity Programming, Use Test Weight Less Than Capacity

E35 Calibration Error 1. Recalibrate, Shift Adjust Can't Compensate More Than 100%


25/332

Chapter 2: 3027 Over/UnderJumpers and Keyboard Functions

(11/97) 2-1

2 3027 Over/UnderJumpers and Keyboard

Functions

Display PCBW1 - Decimal Point, comma display

Out = decimal pt.; In = comma

W2 - ROM Select

Must short (1-2)

W3 - ROM Enable

Must be in

Power Supply PCBW1 - Setup Entry

In = enable; Out = disable

W2 - Internal Suppressor (Use with TTL outputs)

In = connect suppressor; Out = disconnect

Keyboard

KEY SETUP FUNCTION NORMAL FUNCTION

ZERO Back Up To Previous Step Re-Zero Scale

TARE/TARGET Toggle Selections Enter Target Or Tare

CLEAR Advance To [Caloff] Clear Tare Or Target Wgt

UNITS N/A Toggle Units (Lb/Kg)

PRINT Accept Selection Initiate A Print Command


26/332


(11/97)2-2

Softswitch Settings

F0-Span Adjust

1-Enable; 0-DisableF1-Operating Mode0 = NA; 1 = 3026; 2 = NA; 3 = 3036; 4 = NA;

F1.5- Indicator Mode0 = indicator; 1 = over/under

F2-Calibration Units0 = LB; 1 = KG; 2 = lb-oz; 3 = oz; 4 = g;

F3-Units Key 1-LB/KG; 0-Disable; 2 = NA; 3 = LB-g-OZF4-Weight/LED Enable

0 = wgt on, led off; 1 = wgt on, led on;

F4.1-Zone Width Entry

0 = Increments; 1 = % of target;F5-Zero Cursor

1-Enable; 0-DisableF6-Auto Zero Maint.

0 = disable; 1 = .5inc; 2 = 1inc; 3 = 3 inc.F6.1AZM in Net Mode

0 = gross; 1 = gross and net F7-Zero Key Enable

0 = disable; 1 = 2%; 2 = 20%;

3 = 20% GandNet F8-Motion Sensitivity

0 = 1d; 1 = 3d;F9-Filter Selection

0 = disable; 1 = light; 2 = medium; 3 = heavy9.1-Dig. Load Cell Filter

1-Enable; 0-DisableF10-Expanded Weight

1-Enable; 0-DisableF11-Net Wgt. Display

0 = gross wgt; 1 = net diff.

F12-Zone ProgrammingPrint = enter; Tare = skip

12.1-Setup Entry Point

0 = F0; 1 = F1212.2-High Zone Width

Tare = toggle; Print = Select

12.3-High Accept Width

Tare = toggle; Print = Select 12.4-Low Accept WidthTare = toggle; Print = Select

12.5-Low Zone WidthTare = toggle; Print = Select

12.6-Programmable Target Memory1-Enable; 0-Disable

F13-Tare Enable1-Enable; 0-Disable; 2 = auto tare

F14-Auto Clear Tare

1-Enable; 0-DisableF15-Serial Port Program.

Print = enter; Tare = skip15.1-Format

0 = cont. ;1 = demand15.2-Baud Rate

Tare = toggle; Print = Select

15.3-Parity0 = always 0; 1 = odd; 2 = even

15.4-Checksum1-Enable; 0-Disable

15.5-Line Format Select 0 = single line displayed; 1 = GTN single line;2 = GTN multiple line;

15.6-Double Wide Print

1-Enable; 0-Disable15.7-Auto Print

1-Enable; 0-Disable

15.8-Print Wgt. Class.1-Enable; 0-Disable

15.9-Stop Bits0 = 1; 1 = 2;

F16-ASCII Input 1-Enable; 0-Disable

F18-Tare Interlocks

1-Enable; 0-DisableF19-Motion Blanking

1-Enable; 0-DisableCAL-Calibration

Print = enter; Tare = skip


27/332

Chapter 2: 3027 Over/UnderError Codes

(11/97) 2-3

Error Codes

Error Code Description Suggested Corrective ActionE1 Program Memory Fatal 1. Check DC Supply Voltages

2. Replace Display PCB

E2 Internal Ram MemoryFatal Error

1. Check DC Supply Voltages2. Replace Display PCB

E3 NOVRAM Memory Error 1. Check DC Supply Voltages2. Reprogram, Recalibrate3. Replace Display PCB

E8 Communication Loss with DLC 1. Check DC Supply Voltages

2. Check Interconnect Harnesses For Load Cell And PCB’s3. Replace Load Cell4. Replace Display PCB

E9 DLC Out Of Range, Under Capacity 1. Check For Mechanical Bind

2. Check DC Supply Voltages3. Replace Load Cell4. Replace Display PCB

E10 DLC Memory Verify Fatal Error 1. Check DC Supply Voltages2. Replace Load Cell

E11 DLC ROM Error 1. Check DC Supply Voltages


E13 DLC EPROM Error 1. Check DC Supply Voltages

2. Recalibrate Scale3. Replace Load Cell

E16 Math Error 1. Press Clear Key To Clear Error, Check Program And Recalibrate

E32 Insufficient Test Used ForCalibration

1. Recalibrate With At Least 50% Of Programmed Scale Capacity

E34 Test Weight Over Cap 1. Check Capacity Programming, Use Test Weight Less ThanCapacity

E35 Calibration Error 1. Recalibrate, Shift Adjust Can't Compensate More Than 100%


28/332

Chapter 3: 8140 Digital IndicatorJumpers and Keyboard Functions

(11/97) 3-1

3 8140 Digital IndicatorJumpers and Keyboard

Functions All jumpers are in the correct position for standard operation when the unit is

shipped. Check the jumper positioning to be certain they are correct for thisunit’s application.

W1 - External Memory (shorted)

W2 - Calibrate Enable (shorted-enabled, out-disabled)

W3 - EPROM Selection (shorted between 1 and 2)

W4 - Comma Enable (in-comma, out-decimal point)

W5 - Load Cell Output Selection - (pins 1and 2 = 2 mV/V; pins 2 and 3 = 3mV/V)

Zero - Back up to previous step.

Test - Yes or 1

Tare - No or 0

Clear - Skip to S File.

Print - Enter


29/332


(11/97)3-2

Softswitch SettingsTo enter the setup mode, press both the TARE and CLEAR keys, then release at

the same time.

F0 - Span Adjustment 1 to access

F1 - Expand Display1 to enable

F2 - Display Filtering

1-4 to enable low to highF3 - Tare Active

1 activeF4 - Tare Interlock

0 enabledF5 - Auto Clear Tare 1 enabled

1= when +/- 1/2 increment or more of motionare detected; 2 = +/- 2 increments or moreF7 - Pounds CalibrationF8 - Power Up PoundsF9 - LB/KG Switching

1 enabledF10 - Auto Zero Maint.

1 = enabled ± 2%; 2 = enabled ± 20%F11 Analog Verification

1 = enabled

F12 Printer Output 0 = disabled

Demand Mode

1 = Enabled2 - Baud Rate 300, 1200, 2400, 4800, 96003 - Checksum 0 disabled4 - Printer Select

1 = 307, 8804, 8806, 8855, 88602 = 8805 receive mode only3 = 8805 smart mode

4 = 8820/8830 (ram 1)

5 = 8820/8830 (rams 2 and 3)5- Data Format 0 = displayed weight only1 = single line gross, tare, net

2 = multiple line gross, tare, net F13 Net Zero Cursor

0 = gross only; 1 = gross and net F14 Under Zero Blanking

0 = blanks at 3% under;1 = blanks at 5 increments

CAL - Calibration Procedure


30/332

Chapter 3: 8140 Digital IndicatorError Codes

(11/97) 3-3

Error Codes

Error Code Description Suggested Corrective Action

E1 ROM Error Try Power Down/ Replace main PCB

E2 Ram Error Try Power Down/Replace main PCB

E3 NOVRAM Error Try Power Down/ Replace Main PCB

E4 Print Fault Check Printer/Format

E5 Display Verify Error Replace Main PCB

E6 Analog Verify Error Recalibrate

E7 EEROM Error Try Power Down/Replace Main PCB

E8 Scale in Motion Waits Unit Motion Stops

E9 Illegal Configuration Reconfigure Increment Size

E10 Calibration Error Recalibrate

E11 Calibration Error Recalibrate

E12 Over Capacity Reconfigure

E13 Low Capacity Reconfigure

EA Insufficient Test Wt. Use more Test Weights/Try Again

AAAAAA Analog Verify Cycle None: This indicates an AV cycle is in process


31/332

Chapter 4: M8141 Power SupplyJumpers and Keyboard Functions

(11/97) 4-1

4 M8141 Power SupplyJumpers and Keyboard

Functions

JumpersJU1 - Calibrate Enable (shorted-disabled, out-enabled)

JU2 - External memory (installed)

JU3 - 2mV/V or 3mV/V cell selection (in = 2, out = 3)

JU4 - EPROM selection (factory use only)

JU5 - Memory size selection (factory use only)

JU6 - Fiber Optics power (CH1)

1-2 = Powered in sleep and wake modes

2-3 = Powered in wake mode only

JU7 - Fiber Optics

1-2 = Powered in sleep and wake mode

2-3 = Powered in wake mode only

Keyboard0-9 Used to enter setpoint values, commodity ID, time and date, calibration/setupparameters, and tare weight.

FUNCTION Used in conjunction with time, date, setup and ID after data entry.Sleep: With no preceding data entered, this key will put instrument in sleep modeto conserve battery life.

ZERO/WAKEUP Zero: digitally zeros scale. Wakeup : if already asleep, used to re-initialize unit.

PRINT Initiates data outputs to a printer or other device.

LB/KG Mode selection-selects weight units to be used, pounds, kilograms, orother pre-programmed units.

NET/GROSS Mode selection- selects weighing mode.

TARE Enters the displayed weight as tare or is used with keys 0-9 to enter akeyboard tare.

CLEAR Erases erroneous keyboard entries.


32/332


(11/97)4-2

Setup ChartAccessCode Parameter

SelectableValue

AccessCode Parameter

SelectableValue

01 Scale Capacity 1 to 999,999 29 Tare Motion Interlock 0 = Disable, 1 = Enable02 Division Size 0.00001 to 200 30 Printer Data Format 1 = Single Line Weight

03 Print Motion Detect Band 0 to 3 2 = GTN on Single-Line

04 Acquire Dead Load Press ENTER key 3 = G-T-N on 3 Lines

05 Scale Span Enter Weight on Scale 4 = GTN on Single

06 Calibration Units 0 = kg, 1 = lb Line sign correct

07 Display Update Rate 1 to 255 5 = G-T-N on 3

08 Power Up Units 0 = kg, 1 = lb 31 Minimum Print Threshold 0=Disable, 1=up to Cap

09 Digital Zero/Tare Motion 0 to 3 32 Double Width Print 0 = Disable, 1 = Enable

10 Over Capacity Blanking 80 to 110% 33 Scale ID 0 to 12711 C0Z on Net or Gross 0 = Gross, 1 = Net 34 Print Scale ID 0 = Disable, 1 = Enable

12 AZM Delta Band 0 to 3 35 Setpoints 0 = Disable

13 AZM Delta Time Delay 1 to 15 1= Enable on Disp. Wt

14 AZM Aperture 0 to 125 2 =Enable on Gross Wt.

15 Digital Filter 0 to 3 36 Print Inhibit on Motion 0 = Disable, 1 = Enable

16 Display Blanking 0 = Enable, 1 = Disable 37 Zero Print Interlock 0 = Disable, 1 = Enable

17 Negative Gross Weight 0 = Prints Below Zero 38 Line Feed 0 to 10

Printing 1 = No Print Below 0 39 Commodity ID Entry 0 = Disable,

18 lb/kg Switching 0 = Disable, 1 = Enable 1 = Enable Fixed

19 Alternate Display Units Enter Cal/ Alt. units 2=EnableVariable

20 Time and Date 0 = Disable, 1 = Enable 40 Print Complete Time-Out 0 to 5

21 Time and Date Format 0 = None, 1 = US,2 = Canada

41 Dribble/Preact 0 = Disable

22 Printer Output Format Sect. 4.6, Parameter 22 1= Enable -Zero Tolerance

23 Channel 1 Baud Rate 0 = 300, 1 = 1200 2 = Enable -Wgt Tolerance

2 = 4800, 3 = 9600 42 CH 1 Configuration See Sect 4.6, Para. 42

24 Channel 2 Baud Rate 0 = 300, 1 = 1200 43 CH2 Configuration See Sect 4.6, Para. 43

2 = 4800, 3 = 9600 44 Auto Sleep Timer 0 to 255 Minutes

25 Tare Enable 0 = Disable, 1 = Enable 45 Remote Print Indicator 0 = Disable, 1 = Enable

26 Keyboard Tare 0 = Disable, 1 = Enable 46 Printer Checksum Enable 0 = Disable, 1 = Enable

27 Tare Auto Clear 0 = Disable, 1 = Enable 98 Parameter Setup Print all Current Setup

28 Tare Interlock 0 = Disable, 1 = Enable 99 Reset Parameters To Factory Setting


33/332

Chapter 4: M8141 Power SupplyError Codes

(11/97) 4-3

Error Codes

Error Code Description

“--1--” A/D conversion error. The software detected an auto rangecondition during conversion. This can be caused by no load cellhooked up, load cell polarity reverse, or A/D hardware failure.

“--2--” Digital check error. The indicator has detected an internal error,

most likely a calibration data check error. Putting the indicator tosleep, and waking it up will cause the calibration data to be readback in from EEPROM. If the error still persists, then the EEPROMmay be bad.

“--3--” EEPROM read/write error. The indicator has detected a hardwareerror during read or write to the EEPROM. Putting the indicator to

sleep and waking it up will cause a read re-try. Putting theindicator in and out of the setup mode will cause a write re-try. If the error persists, the EEPTOM may be bad.

“--7--” A/D failure. The A/D conversion did not occur within 70ms. Thisis most likely a hardware failure in the A/D section.

“--8--” Setup calibrations not performed. This indicates that a parameter was changed, but the necessary calculations were not performed

to make the indicator operate. Since the calculations areautomatically performed on exit form the setup mode, this errordoes not normally occur. However, see documentation on the

ZERO button for a description of when it might.

Errors 4, 5, and 6 are reserved for future use. If they occur, contact the factory.


34/332

Chapter 5: 8142 IndicatorJumpers and Keyboard Functions

(11/97) 5-1

5 8142 IndicatorJumpers and Keyboard

Functions

Main PCB JumpersW1 - ROM Enable: Must Be (IN)

W2 - Calibration Enable: (In = enabled, Out = disabled)

W3 - Comma Select: (In = comma, Out = period)

W7 - mV/V Selection: (1-2) 2mV/V load cell input; (2-3) 3 mV/V load cell input.

Dual Display PCB

JumpersW2 - Calibration Enable: (In = enabled, Out = disabled)

W5 - Primary Display Comma Select: (In = comma, Out = decimal pt.)

W6 - Auxiliary Display Comma Select: (In = comma, Out = decimal pt.)

W7 - ROM Enable: Must be (IN)

W8-A harness plugs onto this jumper from W2 on the Main PCB.

Rack Display PCB

JumpersW1-Primary Display Comma Select:(Same as W5 above)

W2-Auxiliary Display Comma Select:(Same as W6 above)

Optional BCD/Analog PCB(Dual Display Advanced Rack and Wall Enclosures Only)

BCD/Analog PCB Jumpers

W1-Motion Detect Inhibit: (1-2 = disabled, 2-3 = enabled)

W2-Calibration Enable:(In = enabled, Out = disabled)


35/332


(11/97)5-2

Keyboard Functions

During SetupENTER - accepts the displayed selection and advances to the next setup step.

SETUP - accepts the displayed selection and skips to[S FILE] at the end of setup.

ZERO - accepts the displayed selection and back-up to the previous setup step.

(0 - 9) - used to enter data as required. The 0 key is also used to display thenext selection when a menu of choices is presented.

Quick Reference Chart

Step Description Selections F2.1 Tare Mode 0 = Disable

1 = Keyboard/Auto 2 = Auto Tare Only

F2.2 Tare Interlocks (*) 0 = Disable 1 = Enable

F2.3 Auto Clear Tare 0 = Disabled 1 = Enabled

F2.4 Net Zero Cursor (*) 0 = Disabled 1 = Enabled

F2.5 Keystroke Timeout 0 = Disabled 1 = Enabled

F2.6 Predetermined Tare 0 = Disabled 1 = Enable French W&M

F2.7 Autoprint Threshold 0 = Disabled 1 = Enabled

F3.1 Power-up Timer 0 = Disabled

1 = Enabled

F3.2 Power-up Units 0 = kg Weight Units1 = lb Weight Units

Step Description SelectionsF3.3 Units Switching 0 = Disabled

1 = Enabled

F3.4 Expanded Weight 0 = Disabled 1 = Enabled

F3.5 Span Adjust 0 = Disabled 1 = EnabledF3.6 Display Under Zero 0 = Disabled

1 = Enabled

F3.7 Zero Adjust 0 = Bypass Zero Adjust 1 = Adjust Zero

F4.1 AZM Range (*) 0 = Disabled5 = 0.5 Increment 10 = 1 Increment 20 = 2 Increment 30 = 3 Increment

F4.1A AZM Mode 0 = AZM Gross Mode Only 1 = AZM Net or Gross

F4.2 Motion Range (*) 07 = 0.7 Increment

F4.3 Motion Rate (*) 03 = 3 Updates

F4.4 Digital Filtering 0 = Disabled1 = Light Filter 2 = Medium Filter3 = Heavy Filter4 = Very Heavy Filter


36/332

Chapter 5: 8142 IndicatorQuick Reference Chart

(11/97) 5-3

Step Description SelectionsF4.6 Analog Verify 0 = Disabled

1 = Enabled

F4.7 Pushbutton Zero 0 = Disabled1 = ±2% of Capacity

2 = ±20% of Capacity F5.1 JN Port Mode 1 = Demand (Printer)

2 = Toledo® Continuous3 = Masstron® Continuous4 = Toledo® Short Form

F5.2 JN RS-422 Input 0 = Disabled 1 = Enabled

F5.3 JN Baud Rate 1200 Baud

F5.4 JN Port Checksum 0 = Disabled

1 = Enabled

F5.5 Printer Model Select 1 = Standard 2 = 8805 (Receive Only)3 = 8805 (Smart Mode)4 = 8820/8830 (Ram 1)5 = 8820/8830 (Ram 2,

3)

F5.6 Weight Line Format 1 = Displayed Weight 2 = Single Line G, T, N 3 = Multi Line G , T, N

F5.7 Double Width Print 0 = Disabled 1 = Enabled

F5.8 Minimum Print Increments

F5.9 Printed Legend (*) 1 = "lb" or "kg" 2 = "t" for tons3 = No Legend

F5.10 Negative Net Weight 0 = Disabled1 = Enabled

F5.11 Repeat Print 0 = Disabled 1 = Enabled

Step Description SelectionsF5.12 Demand Format 1 = WT, ID, T&D, CN

2 = IDT&D

WT, CN3 = ID

T&D, CNWT

4 = IDT&D

CNWT5 = T&D

IDCNWT

6 = T&DIDWT, CN

7 = ID, T&D, CNWT

8 = IDT&D

CN, WT

F5.13 Time/Date Format 0 = Disabled1 = MM DD YY2 = DD. MM. YY3 = YY MM DD4 = HH: MM PM MM DD YY 5 = DD. MM. YY HH: MM6 = YY MM DD HH: MM

F5.14 Print ID 0 = Disabled1 = Enabled

F5.15 Print CN 0 = Disabled1 = Enabled

F5.16 Net Sign Print (*) 0 = Disabled 1 = Enabled

F5.17 ASCII Remote Input 0 = Disabled 1 = Command Input Enabled2 = Demand/Continuous


37/332


(11/97)5-4

Step Description SelectionsF5.18 Autoprint/Interlock 1 = Disabled

2 = Print Interlock3 = Autoprint

F5.19 Additional Linefeeds 0 = Skip Linefeed Select

1 = Access Linefeed Select

F5.20 DSR Input Mode 0 = CLEAR1 = TARE2 = PRINT 3 = ZERO4 = Blank Display

F6.1 Recall ID 0 = Disabled

1 = Enabled

F6.2 Recall CN 0 = Disabled

1 = Enabled

F6.3 Recall Time & Date 0 = Disabled1 = Enabled

F6.4 Preset CN 0 = Disabled1 = Enabled

F6.5 Recall Setpoint Data 0 = Disabled1 = Enabled

F6.6 Access Clock Adjust

F7.0 Setpoint Programming Group F7.1 Setpoints Enable 0 = Disabled

1 = Enabled

F7.2 Setpoint Mode 2 = 2, Dual Speed Setpoints4 = 4, Single Speed Setpoint

F7.3 Tolerance Mode 0 = Setpoint Tolerance 1 = Zero Tolerance

Step Description SelectionsF7.4 Zero Tolerance Entry 0 = Disabled

1 = Enabled

F7.5 Tolerance Entry 0 = Disabled1 = Enabled

F7.6 Setpoint Password 0 = Disabled 1 = Enabled

F8.1 JW Port Tare Entry 0 = Disabled

1 = Enabled

F8.2 JW Port ID Entry 0 = Disabled 1 = Enabled

F8.3 Continuous Output 0 = Disabled 1 = Enabled

F8.4 JW Port Baud Rate 9600 Baud

F8.5 JW Port Parity 0 = Always a "0"1 = Odd Parity2 = Even Parity

F8.6 JW Port Stop Bits 1 = 1 Stop Bit 2 = 2 Stop Bits

F8.7 JW Port Checksum 0 = Disabled 1 = Enabled

F8.8 Alpha Barcode Input 0 = Disabled 1 = Enable

F9.1 JY Port Enabled 0 = Disabled

1 = Enabled

F9.2 JY Port RS-485 Input 0 = Disabled 1 = Enabled

F9.3 JY Port Baud Rate 9600 Baud

(*) - Requires specific selection for legal-for-trade applications. Recommended default selections are shown in .


38/332

Chapter 5: 8142 IndicatorError Codes

(11/97) 5-5

Error CodesThe 8142 has 2 types of error codes, operational errors and calibration errors.

Operational Error CodesOperational error codes can occur during power up or while the 8142 is innormal operation. Do no

balanza spider

Documents