11-26-2019

BATHROOM FAUCET WITH POP-UP DRAIN ASSEMBLY 15-B42WP-CH-AV – Polished chrome finish 15-B42WP-BN-AV – Brushed nickel finish 15-B42WP-PB-AV – Polished brass finish

PACKAGE AND HARDWARE CONTENTS

PART DESCRIPTION QUANTITY

C

B

D

A

A Faucet assembly 1B Lift rod assembly 1C Pop-up drain assembly 1D Mounting nut 2

SAFETY INFORMATIONPlease read and understand this entire manual before attempting to assemble, operate or install the product. WARNING • Protect your eyes with safety glasses when cutting or soldering water

supply lines.

CAUTION • If you solder the joints during installation, the seats, cartridges, and washers

must be removed before using a flame or the warranty will be voided on these parts.

• Cover the drain to avoid losing parts.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts.

Estimated Assembly Time: 30 minutesTools required for assembly (not included): adjustable wrenches, groove joint pliers, pipe wrench, Phillips screwdriver, supply lines, thread seal tape, silicone.

Installation may vary depending on how the previous faucet was installed. Supplies necessary for the installation of the faucet are not all included; however, they are available wherever plumbing supplies are sold.

Prior to beginning installation, turn off the hot and cold water lines, then turn on the old faucet to release built-up pressure. When installing the new faucet, hand tighten the connector nuts. DO NOT OVERTIGHTEN. Connections that are too tight will reduce the integrity of the system.

Need Help? Please call our toll-free line at (877) 319-3757 (7:30 a.m. to 4:30 p.m. CST) for additional assistance or service.

Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • HomewerksWW.com

2 HomewerksWW.com

PRODUCT SPECIFICATIONS

Max. Flow Rate: 1.2 GPM (4.54 LPM) at 60 PSI Washerless cartridges

ASME A112.18.1/CSA B125 Manufactured to include no more than 0.25% weighted average lead content on wetted surfacesNSF 61-9

Polished chrome, brushed nickel or polished brass finish Total weight of item: 1.95 lbs.

ASSEMBLY INSTRUCTIONS

1. Turn off water at the supply valve under the sink or at the main water supply. Disconnect the supply lines to the faucet and remove the old faucet.

Clean and dry the surface area where the new faucet will be mounted.

1 5. Apply silicone to the underside of the flange (5.1). From underneath the sink, insert the pop-up drain assembly (C) into the drain opening (5.2) in the sink. From above the sink, screw the flange (5.1) onto the pop-up drain assembly (C). The pivot hole (5.3) must face the back of the sink.

Use groove joint pliers to tighten the nut (5.4) or the sealant may not seal properly. Do not overtighten. Clean away any excess silicone. Open the easy install rotating clip (5.5).

silico

ne

5.3

5.4 C

5.1

5.2

5.5

5

2. Ensure the gasket (2.1) is in place on the bottom of the faucet body (A). Apply a thin bead of silicone sealant to the underside of the gasket (2.1) on the faucet body (A). Insert the faucet body (A) through the mounting holes in the sink (2.2). Secure the faucet body (A) to the sink using the mounting nuts (D).

A2.1

D

2.2

2 6. Insert the stopper (6.1) down into the pop-up drain assembly (C). Install the horizontal rod (6.2) from the lift rod assembly (B) into the pivot hole (6.3) in the pop-up drain assembly (C) as shown in figure B. Make sure the horizontal rod (6.2) is inserted completely into the pop-up drain assembly (C) and that it engages with the stopper (6.1), as shown in figure A. Close the easy install rotating clip (6.4).

6.1

6.1

6.2

C

6.26.3

6.3

6.4

Figure A

Figure B

6

3. To connect the water supply, use 1/2 in. IPS faucet supply lines (3.1) or coupling nuts (3.2) with 3/8 in. O.D. ball-nose risers (3.3).

Wrap thread seal tape around each faucet shank (3.4) in a clockwise direction. Use a wrench to tighten each supply line (3.1) fitting or coupling nut (3.2) to the faucet shanks (3.4). Do not overtighten.

3.3

3.4

3.1

3.2

3 7. If the horizontal rod (7.1) is too long, as shown in figure A, the length can be adjusted.

As shown in figure B, remove the clip (7.2) from the horizontal rod (7.1). Slide the plastic portion of the rod to adjust to the desired length. The excess length (7.3) can be removed where perforated by snapping it off with pliers or cutting it off with a saw.

After the plastic portion of the horizontal rod (7.1) is positioned properly, reinstall the clip (7.2) as shown in figure C.

7.

Wall

1

7.2

7.1

7.3

7.17.2

Figure A

Figure B

Figure C

7

4. Remove the stopper (4.1) and flange (4.2) from the pop-up drain assembly (C). Screw the attached mounting nut (4.3) down the pop-up drain assembly (C) and then push the gasket (4.4) down.

4.1

4.2

C

4.34.4

4

3HomewerksWW.com

ASSEMBLY INSTRUCTIONS

8. Slide the lift rod (8.1) from the lift rod assembly (B) down through the faucet body (A). Push the pivot rod (8.2) to the down position until the stopper (8.3) is completely open. Press the button (8.4) on the slip joint assembly (8.5) and adjust the vertical rod (8.6) along the pivot rod (8.2) until the vertical rod (8.6) is in the correct position to engage with the lift rod (8.1). Press the lift rod (8.1) into the top of the vertical rod (8.6) until it engages. Operate the lift rod (8.1) up and down to verify the stopper (8.3) opens and closes smoothly and completely.

A

B

8.3

8.28.5

8.4

8.2 8.48.5

8.6

8.18 9. After installation is complete,

remove the aerator (9.1) from the spout (9.3) of the faucet body (A).Do not lose the gasket (9.2) from inside the aerator.

Turn on the water supply and allow both hot and cold water to run for at least one minute. This flushes away any debris that could cause damage to the internal parts. While the water is running, check for leaks. Turn off the water and screw the aerator (9.1) back onto the spout (9.3) of the faucet body (A).

A9.1

9.2

9.3

9

OPERATING INSTRUCTIONSThe lever handles control the flow of hot and cold water to the faucet.Rotate the right handle forward for cold water. Rotate the left handle forward for hot water. Moving the handles forward opens the cartridges and causes water to flow from the spout. The degree of handle opening determines the volume of water flow. Returning the handles to the original position stops the flow of water.

CARE AND MAINTENANCEClean periodically with a soft cloth. Avoid abrasive cleaners, steel wool, and harsh chemicals as these will dull the finish and void your warranty.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTIONFaucet leaks underneath handle. Bonnet has come loose or O-ring on cartridge

is dirty or twisted.1. Move the handle to the OFF position. Unscrew the handle screw and remove

the handle.2. Tighten the bonnet by turning it clockwise. Move the cartridge stem to the ON

position. The leak should stop draining out from around the cartridge stem.3. If the leak does not stop, shut off the water supply. Remove the bonnet by

turning it counterclockwise. Lift out the cartridge valve. Inspect the larger O-ring on the cartridge bonnet and the smaller O-ring on the cartridge stem. Remove any debris from the O-rings. If either O-ring is twisted, straighten it. If either O-ring is damaged, replace the cartridge by calling customer service.

4. Position the cartridge back into the faucet body. Make sure the ridges on the two sides of the cartridge bonnet fit into the grooves on the two sides of the faucet body. Tightly screw the bonnet onto the faucet body.

5. Reinstall the handle.

Water does not completely shut off.

Rubber valve seat is dirty, stuck, or broken. 1. Shut off the water supply.2. Remove the handle from the faucet body. Loosen the bonnet by turning it

counterclockwise. Lift out the cartridge assembly.3. Inspect the rubber valve seat in the faucet body. If there is debris or brass

scrap on the surface of the seat, remove it. If the rubber seat is stuck tightly in the water inlet hole, push it gently with a fingertip so it moves up and down smoothly. The spring (smaller end up) must be placed back underneath the valve seat. If the rubber valve seat is worn out or broken, replace the cartridge by calling customer service.

4. Position the cartridge back into the faucet body. Make sure the ridges on the two sides of the cartridge bonnet fit into the grooves on the two sides of the faucet body. Tightly screw the bonnet onto the faucet body.

5. Reinstall the handle.

Faucet leaks around aerator. The aerator is incorrectly fitted, dirty, or small parts inside the aerator are improperly installed.

1. Remove the aerator from the spout by turning it clockwise. Inspect the black rubber packing inside the aerator. The rubber packing should be flat.

2. Screw the aerator back onto the spout and tighten.

Faucet has an improper water pattern.

The aerator is dirty or small parts inside the aerator are improperly installed.

1. Remove the aerator from the spout by turning it clockwise.2. Gently flush the small parts inside the aerator to clear away any debris.3. Reinstall the small parts as shown in the replacement parts exploded diagram.

Metal screens must be flat and plastic supporter must be straight.4. Screw the aerator back onto the spout and tighten.

4 HomewerksWW.com

ROUGH-IN

4"

3-3/8"

1-1/4"

9-1/4"

2-1/8"

1-5/8"

4-1/4"5-3/4"

1/2"-14NPSM-2A

REPLACEMENT PARTS

For replacement parts, call our customer service department at (877) 319-3757, 7:30 am - 4:30 pm, CST, Monday - Friday.

PART DESCRIPTION PART #

10-B421-CH-AV 10-B421-BN-AV 10-B421-PB-AV

1 Handle hot RP13244CH RP13244BN RP13244PB

2 Handle cold RP13245CH RP1245BN RP13245PB

3 Screw RP50002 RP50002 RP50002

4 Hot index button RP10004 RP10004 RP10004

5 Cold index button RP10005 RP10005 RP10005

6 Bonnet RP64124 RP64124 RP64124

7 Washer RP70193 RP70193 RP70193

8 Bolt and cartridge RP50168 RP50168 RP50168

9 Washer and spring RP22008 RP22008 RP22008

10 Aerator assembly RP30216CH RP30216BN RP30216PB

11 Mounting nut RP56001 RP56001 RP56001

12 Lift knob and rod assembly RP40235CH RP40235BN RP40235PB

13 Pop-up drain assembly RP40191CH RP40191BN RP40191PB

LIMITED LIFETIME WARRANTYThe distributor warrants to the original consumer purchaser this product to be free from defects in material and workmanship under normal use in residential applications. At its option, the Company will provide repair parts or replace defective product when the product is used in accordance with the manufacturer’s specifications. Use of mild abrasive, abrasive or chemical cleaners may damage the finish of the faucet. We recommend cleaning your faucet with a soft cloth, moistened with water. Damage resulting from the use of abrasive or chemical cleaners SHALL VOID THIS WARRANTY.This warranty is not applicable to any products or parts of products where damage is caused by use of non-genuine parts; is due to installation error, product misuse, negligence or faulty maintenance; or where the product is not installed according to local building codes.

This warranty excludes labor charges or damage incurred during installation, repair or replacement, and any indirect, incidental or consequential damages, losses, injury or costs of any nature. This warranty is in lieu of and excludes all other warranties, conditions and guarantees, whether expressed or implied, including without restriction those of merchantability or fitness of use.Liability under this warranty will not exceed the purchase price for the product claimed to be defective by the original consumer purchaser. Some states or provinces do not allow the exclusion or limitation of consequential damages so the above limitations or exclusions may not apply. This warranty gives you specific legal rights and you may also have other rights which vary from state to state, or province to province. Inquiries regarding warranty claims can be directed to (877) 319-3757, 7:30 a.m. to 4:30 p.m., CST, Monday - Friday.