bdk - coiled tubing equipment

228

Coil Tubing EquipmentCoil Tubing EquipmentThe coil tubing product line has also developed out of the B.D.Kendle stable in response to service industry requirementsfor flexible, effective, equipment. Development has been directed by end-user input, with BDK products settingworldwide standards for products such as the Dimple-on Connector. WCS Coil Tubing products cover the range of CTequipment needs, including fittings for the CT itself, CT surface equipment, CT Bottom Hole Assembly products, andindividual CT service tools.

Weatherford products and services are subject to Weatherford’s standard terms andconditions. For more information concerning the full line of Weatherford products andservices, please contact your authorized Weatherford representative. Unless notedotherwise, trademarks and service marks noted herein are the property of Weatherford.230

© 2002. Weatherford. All rights reserved.

Coiled Tubing Thread ConnectionsWeatherford BDK® Coiled Tubing Tools can be supplied with different styles of thread to suitcustomer requirements. The tables below are intended as a guide to show the standard connectionthreads that BDK offer and are not meant to be exhaustive.

MinimumOD

MaximumID

Thread Dia. (Nom)H2S Service Yield

Strength'O'-Ring Part No.

1.250" 0.562" 1.000" - 10 SA 30,830 lb 2 x 115 4012

1.500" 0.562" 1.125" - 10 SA 49,440 lb 1 x 120 4020

1.500" 0.625" 1.250" - 12 UN 40,340 lb 1 x 121 4022

1.750" 0.750" 1.500" - 10 SA 40,050 lb 2 x 215 4009

* 2.000" 1.062" 1.700" - 10 SA 61,720 lb 1 x 129 4008

2.250" 1.125" 1.812" - 10 SA 103,180 lb 2 x 221 4010

2.500" 1.500" 2.000" - 10 SA 90,620 lb 1 x 328 7059

2.500" 1.375" 2.062" - 10 SA 115,600 lb 2 x 223 4011

* NOTE: This thread is not interchangeable with the Nowsco 1.700" - 10 SA (Part No. - 320016)

MinimumOD

MaximumID



2.750" 1.500" 2.375" D.S.I. 134,600 lb 1 x 227 4868 Cont..

Figures based on SMYS = 80 ksi for H2S Service with Minimum OD and Maximum ID.

DS Style

PAC Style



Coiled Tubing Thread Connections

MinimumOD

MaximumID



1.750" 0.625" 1.000" - 6 45,400 lb 1 x 122 4026

1.750" 0.750" 1.250" - 6 62,650 lb 1 x 124 4027

2.125" 1.000" 1.500" - 6 84,730 lb 1 x 128 4028

MinimumOD

MaximumID



2.187" 0.625" 1.250" - 7 103,530 lb 1 x 222 4024

3.125" 1.000" 2.375" - 5 250,330 lb 1 x 331 4025

MinimumOD

MaximumID



1.250" 0.562" 1.062" - 16 UN 25,500 lb 1 x 116 3004

1.375" 0.688" 1.062" - 12 SA 33,180 lb 1 x 119 320007

1.500" 0.625" 1.125" - 10 SA 44,740 lb 1 x 120 320008

1.687" 0.875" 1.375" - 10 SA 53,660 lb 1 x 124 320010

1.687" 1.000" 1.469" - 12 SA 38,420 lb 1 x 125 320013

2.000" 1.000" 1.562" - 8 SA 73,460 lb 1 x 127 320014

* 2.125" 1.000" 1.700" - 10 SA 94,110 lb 1 x 129 320016

2.125" 1.500" 1.875" - 10 SA 53,890 lb 1 x 132 320017

2.375" 1.563" 2.080" - 10 SA 72,550 lb 1 x 225 320019

2.875" 1.875" 2.500" - 8 SA 114,000 lb 1 x 141 9740

2.750" 1.125" 2.125"- 8 SA 180,350 lb 1 x 226 320020

3.125" 2.125" 2.650 - 8 SA 127,090 lb 1 x 144 & 1 x 145 320023

3.125" 1.125" 2.500" - 5 ACME 208,200 lb 1 x 228 10354

* NOTE: This thread is not interchangeable with the DS Style 1.700" - 10 SA (Part No. - 4008)

Figures based on SMYS = 80 ksi for H2S Service with Minimum OD and Maximum ID.

REGULAR Style

NOWSCO Style

AMMT Style



CT Dimple-On ConnectorThe Weatherford Dimple-On ConnectorBDK® is an inline typeCoiled Tubing connector designed and manufactured to joinCoiled Tubing to the Bottom Hole Assembly.This type of coiled tubing connector offers the operator a non-upsetconnection and is designed to withstand heavy jarring and drillingoperations.The Dimple-On Connector has been in service since September1996 in Qatar and many other geographical locations.

Superior mechanical strength (comparable with that of theCoiled Tubing)Connector make up time; typically 10 -15 minutesLarge through boreCan be used with 70, 80, 90 ,100, 1100 & 1200 ksi yieldCoiled TubingRe-useable connectorHydraulic installationTorque thro connector

Robust DesignEasy installation into the coiled tubing

Fishing operations standard & heavy dutyMilling applicationsCoiled tubing conveyed drilling operationsExtended reach operations

Features

Benefits

Applications

Thread x Dimple-on

Dimple-on x Dimple-on



Dimple-On ConnectorCoiled Tubing Coiled Tubing Assembly Number Assembly Number

Diameter Wall Thickness Thread x Dimple On Dimple-On x Dimple On

1.250" 0.095" 9382-XXXX 9382

1.250" 0.102" 9383-XXXX 9383

1.250" 0.109" 9384-XXXX 9384

1.250" 0.118" 10956-XXXX 10956

1.250" 0.125" 9385-XXXX 9385

1.250" 0.134" 9386-XXXX 9386

1.250" 0.156" 9387-XXXX 9387

1.500" 0.095" 7342-XXXX 7342

1.500" 0.102" 7343-XXXX 7343

1.500" 0.109" 7344-XXXX 7344

1.500" 0.118" 12007-XXXX 12007

1.500" 0.125" 7345-XXXX 7345

1.500" 0.134" 7346-XXXX 7346

1.500" 0.145" 12134-XXXX 12134

1.500" 0.156" 7347-XXXX 7347

1.500" 0.175" 7348-XXXX 7348

1.500" 0.188" 8174-XXXX 8174

1.500" 0.190" 8174-190-XXXX 8174-190

1.750" 0.109" 7349-XXXX 7349

1.750" 0.118" 11460-XXXX 11460

1.750" 0.125" 7350-XXXX 7350

1.750" 0.134" 7351-XXXX 7351

1.750" 0.145" 12564-XXXX 12564

1.750" 0.156" 7352-XXXX 7352

1.750" 0.175" 7353-XXXX 7353

1.750" 0.188" 7354-XXXX 7354

1.750" 0.190" 7354-190-XXXX 7354-190

1.750" 0.203" 12129-XXXX 12129

Ordering Information :

XXXX refers to connection. Refer to connection TSS for information

The dimple on connector can be used to join differing wall thicknesses together

Example : To join 1.250" 0.095"WT and 0.109" WT the part number would be 9382-9384

Cont…



Dimple-On ConnectorCoiled Tubing Coiled Tubing Assembly Number Assembly Number

Diameter Wall Thickness Thread x Dimple On Dimple-On x Dimple On

2.000" 0.109" 7355-XXXX 7355

2.000" 0.188" 12488-XXXX 12488

2.000" 0.125" 7356-XXXX 7356

2.000" 0.134" 7357-XXXX 7357

2.000" 0.156" 7358-XXXX 7358

2.000" 0.175" 7359-XXXX 7359

2.000" 0.188" 7360-XXXX 7360

2.000" 0.190" 7360-190-XXXX 7360-190

2.000" 0.203" 7361-XXXX 7361

2.375" 0.109" 7362-XXXX 7362

2.375" 0.125" 7363-XXXX 7363

2.375" 0.134" 7364-XXXX 7364

2.375" 0.145" 11018-XXXX 11018

2.375" 0.156" 7365-XXXX 7365

2.375" 0.175 7366-XXXX 7366

2.375" 0.188" 7367-XXXX 7367

2.375" 0.190" 7367-190-XXXX 7367-190

2.375" 0.203" 7368-XXXX 7368

2.875" 0.125" 8187-XXXX 8187

2.875" 0.156" 8132-XXXX 8132

2.875" 0.188" 9059-XXXX 9059

2.875" 0.190" 9059-190-XXXX 9059-190

2.875" 0.203" 10265-XXXX 10265

3.500" 0.134" 11903-XXXX 11903

3.500" 0.156" 11904-XXXX 11904

3.500" 0.175" 11905-XXXX 11905

3.500" 0.188" 11906-XXXX 11906

3.500" 0.190" 11906-190-XXXX 11906-190

3.500" 0.203" 11907-XXXX 11907


XXXX refers to connection. Refer to connection TSS for information





CT Dimple-OnHydraulic Yoke & JigThe Weatherford BDK Hydraulic Yoke and Jig is anessential tool for making up the BDK Dimple-OnConnectors. The hydraulic yoke & jig assembly iscompact, easy to install and simple to operate.

The Hydraulic Yoke can be operated via a hydraulichand pump or control panelThe dimple on jig is designed to suit all wallthickness & size of Coiled TubingThese tools offer a fast, efficient and safe means ofconnecting the Coiled Tubing Connector to theCoiled Tubing. Once the connection is made it hasthe same tensile and torque capability as the CoiledTubing

Robust designEasy to operateKnown hydraulic pressure values to ensure correctlyformed dimplesTime saving during make up of bottom holeassembly

Designed for the installation of all the BDK coiledtubing dimple on product range

®

Features

Benefits

Applications

STAGE 1 STAGE 2 STAGE 3

STAGE 4

STAGE 5

YOKE

COILEDTUBING

DIMPLE-ONCONNECTOR

JIG



CT Dimple-On Hydraulic Yoke & Jig

Coiled TubingSize

Part NumberYoke

Part NumberJig

Weight Yoke - Jig(kg)

Operating Pressure1 - 2 Indentations

1.250" 7297 7305-05 23 - 7.0 3000 - 6000 psi

1.500" 7297 7305-01 23 - 6.5 3000 - 6000 psi

1.750" 7297 7305-02 23 - 6.0 3000 - 6000 psi

2.000" 7297 7305-03 23 - 5.5 3000 - 6000 psi

2.375" 7297 7305-04 23 - 4.75 3000 - 6000 psi

2.875" 8280 8281-01 48 - 11.0 3000 - 6000 psi

3.500" 8280 8281-02 48 - 9.5 3000 - 6000 psi



CT Internal combinationReamer System (I.C.R.S.)The Weatherford BDK Internal Combination Reamer System (ICRS) is ahand operated, self-aligning unit, that prepares the Coiled Tubing to accept anElastomer Sealed Inline Connector.Use of this system ensures that the Elastomer Seal remains undamaged duringinstallation.Two Styles of cutter are available.The Reamer style cutter is used to produce an acceptable seal bore finish on thetubing ID, whilst the De-burr/Bevel style cutter is used to remove any sharpedges from the Coiled Tubing which would otherwise cut the seal.By Changing out the Tubing Bush and selecting the correct size of Reamer theICRS can be used on any size of Coiled Tubing.If there is a need to remove a large amount of material it is recommended thata Multi-Stage Reamer System be used. This allows the optimum amount ofmaterial to be removed for ease of operation, whilst giving an improvedsurface finish.

Self-centering retainer sleeveDepth adjustmentInternal Reamer designed to provide precision finish to Coiled TubingBoreDe-burring/Bevel Cutter creates a beveled lead in for elastomersCan be supplied with a through Bore allowing installation of StiffWireline Connectors

Robust DesignEasy to operateReduces time to install coiled tubing end connectorReduces the failure rate of elastomer seals on the coiled tubing connector

To be utilised when installing any internal coiled tubing connector toremove the weld seam to prevent the elastomer sealing area from gettingdamaged during make up

®

Features

Benefits

Applications

ReamerCutter

De-Burr / Bevel



Internal Combination Reamer SystemAssembly Number Coiled Tubing Size Weight (kg)

10808 1.250" tbc

9301 1.500" - 2.375" 7

9346 2.875" - 3.500" 11



CT Reelable Dimple-OnConnectorThe Weatherford BDK Reelable Dimple-On Connector is available in bothDimple-On and Roll-On styles. The Dimple-On is generally preferred as iteliminates the stress raisers experienced at the Roll-On groove/tube interface.The central part of the connector has a smooth through bore and notchedexterior profile. The notches allow a plastic bending modulus equal to theCoiled Tubing whilst preserving the OD so that the connector can be passedthrough the injector chains and the stuffing box. Elastomer infills with-in theflexi-grooves are sometimes required (depending on operation) to provide aflush outer diameter which will not damage the seals when running through theStuffing Box. Tapered end spigots support the Coiled Tubing preventing flaring.

Superior mechanical strength (comparable with that of the Coiled Tubing)Connector make up time - typically 10 -15 minutesLarge through boreCan be used with 70, 80, 90, 100, 1100 & 1200 ksi yield Coiled TubingRe-useable connectorElastomer infills within the flexi-grooves are sometimes required(depending on operation) to provide a flush outer diameter which willnot damage seals when running through the Stuffing BoxHydraulic installationTorque thro' connector

Robust DesignEasy installation into the coiled tubingReelable design allows the coiled tubing to be joined then spooled over thereel core diameter as well as the gooseneck radiusEliminates the requirement to weld coiled tubing for extended reachapplications

Fishing operationsExtended reach operations

®

Features

Benefits

ApplicationsStandard

OptionalPolyurethane Infill



CT Reelable Dimple-On ConnectorAssembly Number Coiled Tubing Coiled Tubing Assembly Number

Standard Diameter Wall Thickness Polyurethane Infill

12012 1.250" 0.095" 12012-P

12013 1.250" 0.102" 12013-P

12014 1.250" 0.109" 12014-P

12015 1.250" 0.118" 12015-P

12016 1.250" 0.125" 12016-P

12017 1.250" 0.134" 12017-P

12018 1.250" 0.156" 12018-P

8905 1.500" 0.095" 8905-P

8269 1.500" 0.102" 8269-P

6563 1.500" 0.109" 6563-P

9994 1.500" 0.125" 9994-P

9995 1.500" 0.134" 9995-P

12019 1.500" 0.156" 12019-P

8917 1.500" 0.175" 8917-P

8559 1.750" 0.109" 8559-P

12020 1.750" 0.118" 12020-P

12021 1.750" 0.125" 12021-P

12022 1.750" 0.134" 12022-P

12023 1.750" 0.156" 12023-P

12024 1.750" 0.175" 12024-P

12025 1.750" 0.188" 12025-P

12025-190 1.750" 0.190" 12025-190-P


Add suffix "H" to part numbers for H2S service





CT Reelable Dimple-On ConnectorAssembly Number Coiled Tubing Coiled Tubing Assembly Number

Standard Diameter Wall Thickness Polyurethane Infill

10350 2.000" 0.125" 10350-P

10351 2.000" 0.134" 10351-P

12122 2.000" 0.156" 12122-P

12029 2.000" 0.175" 12029-P

11923 2.000" 0.188" 11923-P

11923-190 2.000" 0.190" 11923-190-P

12031 2.000" 0.203" 12031-P

12032 2.375" 0.109" 12032-P

12033 2.375" 0.125" 12033-P

12034 2.375" 0.134" 12034-P

11076 2.375" 0.145" 11076-P

12035 2.375" 0.156" 12035-P

11027 2.375" 0.175" 11027

6969 2.375" 0.188" 6969-P

6969-190 2.375" 0.190" 6969-190-P

12036 2.375" 0.203" 12036-P

12038 2.875" 0.125" 12038-P

8128 2.875" 0.156" 8128-P

12026 2.875" 0.175 12026-P

12037 2.875" 0.188" 12037-P

12037-190 2.875" 0.190" 12037-190-P

12039 3.500" 0.134" 12039-P

12040 3.500" 0.156" 12040-P

12041 3.500" 0.175" 12041-P

12042 3.500" 0.188" 12042-P

12042-190 3.500" 0.190" 12042-190-P

12043 3.500" 0.203" 12043-P







CT Reelable Roll-OnConnectorThe Weatherford BDK® Reelable Roll-On Connector provides aneffective inline connection.The central part of the connector has a smooth through bore andnotched exterior profile. The notches allow a plastic bending modulusequal to the Coiled Tubing whilst preserving the OD so that theconnector can be passed through the injector chains and the stuffingbox. Elastomer infills with-in the flexi-grooves are sometimes required(depending on operation) to provide a flush outer diameter which willnot damage the seals when running through the Stuffing Box. Taperedend spigots support the Coiled Tubing preventing flaring.

Flush OD with coiled tubingRe-usable connectionElastomer infills within the flexi-grooves are sometimes required(depending on operation) to provide a flush outer diameter whichwill not damage seals when running through the Stuffing Box

Reelable design allows the coiled tubing to be joined then spooledover the reel core diameter as well as the gooseneck radiusEliminates the requirement to weld coiled tubing for extended reachapplications

Standard coiled tubing operationsFishing operations

Features

Benefits

Applications

pO tionalPolyurethane Infill

Standard



Reelable Roll-On ConnectorCoiled Tubing Coiled Tubing Assembly Number Assembly Number

Diameter Wall Thickness Standard Polyurethane Infill

1.250" 0.087" 12047 12047-(P)

1.250" 0.095" 12048 12048-(P)

1.250" 0.102" 12049 12049-(P)

1.250" 0.109" 12050 12050-(P)

1.250" 0.118" 10240 10240-(P)

1.250" 0.125" 6425 6425-(P)

1.250" 0.134" 12051 12051-(P)

1.250" 0.148" 12052 12052-(P)

1.250" 0.156" 12053 12053-(P)

1.500" 0.087" 12054 12054-(P)

1.500" 0.095" 4333 4333-(P)

1.500" 0.102" 12055 12055-(P)

1.500" 0.109" 6370 6370-(P)

1.500" 0.118" 12056 12056-(P)

1.500" 0.125" 10842 10842-(P)

1.500" 0.134" 12058 12058-(P)

1.500" 0.148" 12059 12059-(P)

1.500" 0.156" 12060 12060-(P)

1.500" 0.175" 12061 12061-(P)

1.500" 0.188" 12062 12062-(P)

1.500" 0.190" 12062-190 12062-190-(P)

1.500" 0.203" 12063 12063-(P)

1.750" 0.087" 12064 12064-(P)

1.750" 0.095" 12065 12065-(P)

1.750" 0.102" 12066 12066-(P)

1.750" 0.109" 6727 6727-(P)

1.750" 0.118" 12067 12067-(P)

1.750" 0.125" 12068 12068-(P)

1.750" 0.134" 12069 12069-(P)

1.750" 0.148" 12070 12070-(P)

1.750" 0.156" 11053 11053-(P)

1.750" 0.175" 11054 11054-(P)

1.750" 0.188" 12071 12071-(P)

1.750" 0.190" 12071-190 12071-190-(P)

1.750" 0.203" 12072 12072-(P)


The Reelable Roll-On Connector can be used to join differing wall thicknesses together

Example : To join 2 3/8" OD (0.109" WT) with 2 3/8" OD (0.125" WT), the part number would be12078-12079



Reelable Roll-On ConnectorCoiled Tubing Coiled Tubing Assembly Number Assembly Number

Diameter Wall Thickness Standard Polyurethane Infill

2.000" 0.095" 12073 12073-(P)

2.000" 0.109" 12074 12074-(P)

2.000" 0.125" 7172 7172-(P)

2.000" 0.134" 7173 7173-(P)

2.000" 0.148" 12075 12075-(P)

2.000" 0.156" 7406 7406-(P)

2.000" 0.175" 7139 7139-(P)

2.000" 0.188" 12076 12076-(P)

2.000" 0.190" 12076-190 12076-190-(P)

2.000" 0.203" 12077 12077-(P)

2.375" 0.109" 12078 12078-(P)

2.375" 0.125" 12079 12079-(P)

2.375" 0.134" 12080 12080-(P)

2.375" 0.156" 4216 4216-(P)

2.375" 0.175" 9220 9220-(P)

2.375" 0.188 6968 6968-(P)

2.375" 0.190" 12379 12379-(P)

2.375" 0.204 11055 11055-(P)

2.875" 0.156" 4215 4215-(P)

2.875" 0.175" 11295 11295-(P)

2.875" 0.188" 11296 11296-(P)

2.875" 0.190" 11296-190 11296-190-(P)

2.875" 0.203" 11375 11375-(P)


The Reelable Roll-On Connector can be used to join differing wall thicknesses together

Example : To join 2 3/8" OD (0.109" WT) with 2 3/8" OD (0.125" WT), the part number would be12078-12079



CT Roll-On ConnectorThe Weatherford CBDK® oiled Tubing Roll-On Connector is aninline connector and is utilized for standard coiled tubingapplications.

The connector is manufactured for a specific wall thickness and iseasy and quick to install.

Flush OD with coiled tubingTorque thro connector

Robust DesignRe-usable connection

All standard coiled tubing operationsJoining two different wall thickness of coiled tubing

Features

Benefits

Applications

Roll-On x Roll-On

Thread x Roll-On



Roll-On ConnectorCoiled Tubing Coiled Tubing Assembly Number Assembly Number

Diameter Wall Thickness Thread x Roll-On Roll-On x Roll-On

1.250" 0.087" 4350 4350-XXXX

1.250" 0.095" 4351 4351-XXXX

1.250" 0.102" 4641 4641-XXXX

1.250" 0.109" 4352 4352-XXXX

1.250" 0.118" 5422 5422-XXXX

1.250" 0.125" 4353 4353-XXXX

1.250" 0.134" 4354 4354-XXXX

1.250" 0.148" 6022 6022-XXXX

1.250" 0.156" 4355 4355-XXXX

1.500" 0.087" 4327 4327-XXXX

1.500" 0.095" 4328 4328-XXXX

1.500" 0.102" 6303 6303-XXXX

1.500" 0.109" 4329 4329-XXXX

1.500" 0.118" 9760 9760-XXXX

1.500" 0.125" 4330 4330-XXXX

1.500" 0.134" 4331 4331-XXXX

1.500" 0.148" 6023 6023-XXXX

1.500" 0.156" 4332 4332-XXXX

1.500" 0.175" 5515 5515-XXXX

1.500" 0.188" 5516 5516-XXXX

1.500" 0.190" 5516-190 5516-190-XXXX

1.500" 0.203" 5517 5517-XXXX

1.750" 0.087" 4337 4337-XXXX

1.750" 0.095" 4338 4338-XXXX

1.750" 0.102" 6105 6105-XXXX

1.750" 0.109" 4342 4342-XXXX

1.750" 0.118" 6106 6106-XXXX

1.750" 0.125" 4339 4339-XXXX

1.750" 0.134" 4340 4340-XXXX

1.750" 0.148" 6024 6024-XXXX

1.750" 0.156" 4341 4341-XXXX

1.750" 0.175" 5518 5518-XXXX

1.750" 0.188" 5519 5519-XXXX

1.750" 0.190" 5519-190 5519-190-XXXX

1.750" 0.203" 5520 5520-XXXX


XXXX refers to connection. See TSS No FC 166 for information

The Roll-On Connector can be used to join differing wall thicknesses together

Example : To join 2 3/8" OD (0.109" WT) with 2 3/8" OD (0.125" WT), the part number would be 7449-6883



Roll-On ConnectorCoiled Tubing Coiled Tubing Assembly Number Assembly Number

Diameter Wall Thickness Thread x Roll-On Roll-On x Roll-On

2.000" 0.095" 5642 5642-XXXX

2.000" 0.109" 4187 4187-XXXX

2.000" 0.125" 5643 5643-XXXX

2.000" 0.134" 4644 4644-XXXX

2.000" 0.148" 6025 6025-XXXX

2.000" 0.156" 4073 4073-XXXX

2.000" 0.175" 5644 5644-XXXX

2.000" 0.188" 5645 5645-XXXX

2.000" 0.190" 5645-190 5645-190-XXXX

2.000" 0.203" 5646 5646-XXXX

2.375" 0.109" 7449 7449-XXXX

2.375" 0.125" 6883 6883-XXXX

2.375" 0.134" 6884 6884-XXXX

2.375" 0.156" 4231 4231-XXXX

2.375" 0.175" 9221 9221-XXXX

2.375" 0.188" 7170 7170-XXXX

2.375" 0.190" 7170-190 7170-190-XXXX

2.375" 0.203 11329 11329-XXXX

2.875" 0.156" 7171 7171-XXXX

2.875" 0.175" 12044 12044-XXXX

2.875" 0.188" 12045 12045-XXXX

2.875" 0.190" 12045-190 12045-190-XXXX

2.875" 0.203" 12046 12046-XXXX


XXXX refers to connection. See TSS No FC 166 for information

The Roll-On Connector can be used to join differing wall thicknesses together

Example : To join 2 3/8" OD (0.109" WT) with 2 3/8" OD (0.125" WT), the part number would be 7449-6883

252

Coil Tubing EquipmentOutline Connecttors



CT Crimping ToolThe Weatherford BDK Crimping Tool is supplied with special profilecrimping wheel to allow assembly of Coiled Tubing Roll-On Connectorand also a cutter wheel for removing the Coiled Tubing.When installing a roll on connector to the coiled tubing the best method ofdeforming the coiled tubing into the roll on connector grooves is by utilizingthis tool.Spare wheels are available and recommended when ordering theCrimping Tool.

Light weight in design

Robust DesignEasy to handle & operate

The BDK crimping tool can be utilized with any style of roll onconnector

®

Features

Benefits

Applications

CRIMPINGWHEEL

CUTTINGWHEEL



CT Grub Screw ConnectorThe Weatherford BDK Grub Screw Connector is an outline connectormanufactured to suit a specific size of Coiled tubing.

A specially designed Grub Screw retains the Coiled Tubing within theConnectorDual elastomer sealGrub Screw Connector is available for any combination of Coiled Tubingand Thread sizesAll Outline Connectors are fitted with double Back-up Rings to ensure goodsealing capability

Robust in designEasy installation onto the coiled tubing

Standard coiled tubing applicationsMemory PLT operationsE-Line operations - standard

®

Features

Benefits

Applications



CT Grub Screw ConnectorAssembly Coiled Tubing Outside Stab In Depth Number of Weight

Number Diameter Diameter Diameter Grubsrews (kg)

5677-XXXX 1.250" 1.750" 2.87" 8 1.3

4648-XXXX 1.500" 2.000" 3.62" 12 2.3

5290-XXXX 1.750" 2.250" 4.00" 12 2.4

4007-XXXX 2.000" 2.500" 4.00" 12 2.4

5678-XXXX 2.375" 2.875" 4.00" 12 3.0

5679-XXXX 2.875" 3.375" 4.00" 12 3.2

5680-XXXX 3.500" 4.000" 4.00" 12 5.4



XXXX denotes connection type, refer to connection technical sales sheet



CT Grub Screw Preparation &Removal ToolThe Weatherford BDK Grub Screw Connector Preparation Tool incorporatesspecially profiled screws for preparation of the Coiled Tubing prior to assemblyof the BDK Grub Screw Connector.The preparation tool is designed that once the coiled tubing as been prepared forthe coiled tubing connector the preparation tool can be installed and the profiledsetting screws secured into the coiled tubing causing the coiled tubing to deformto a pre-determined depth.Once the coiled tubing tool as been deformed to the pre determined depth thepreparation tool can be removed and the end connector can be installed.

The sliding hammer action has a dual releasing feature and can bereversed for removal of the Grub Screw ConnectorPre-set length on the preparation tool indentation screws to ensurethat the coiled tubing is deformed to the correct depth

Robust DesignEasy to operateLow maintenance costs

All standard coiled tubing operations where a coiled tubinggrub screw connector is utilized

®

Features

Benefits

Applications



CT Grub Preparation & Removal ToolAssembly Coiled Tubing Dimple Head Overall Weight

Number Diameter Box Depth Length (kg)

5764-XXXX 1.250" 2.87" 22.40" 9.7

4769-XXXX 1.500" 3.62" 23.40" 11.0

5771-XXXX 1.750" 4.00" 23.90" 13.2

5773-XXXX 2.000" 4.00" 25.60" 14.4

5775-XXXX 2.375" 4.00" 25.70" 17.5

5777-XXXX 2.875" 4.00" 26.40" 20.0

5779-XXXX 3.500" 4.00" 25.70" 23.2



Weights exclude connection



CT Heavy Duty GrappleConnectorThe Weatherford BDK Heavy Duty Grapple Connector has been developedfor use with velocity strings and more none standard coiled tubingapplications. The coiled tubing connector as a larger OD than the compact /slimline version and a new style grapple arrangement.

The connector utilizes a modified buttress form helical feature rather thana conventional taper to close the grapple onto the Coiled TubingDue to the grapple design it will grip better on oval coiled tubingIt is suitable for high tensile loads and out-performs other styleGrapple Connectors, whilst being easy to make-up and useAll BDK Outline Connectors are fitted with double Back-up Rings toensure good sealing capabilityThe coiled tubing grapple connector can also be manufactured with ametal x metal sealThe BDK Heavy Duty Grapple is available in a Grapple x GrappleStyle for joining velocity strings

All coiled tubing operationsFishing operationsMilling operationsE-Line operationsVelocity string installationsESP installations

®

Features

Applications



CT Heavy Duty Grapple ConnectorAssembly Outside Working Make Up Weight

Number Diameter Pressure Length (kg)

11208-XXXX 2.750" 10,000psi 13.51" 5.9

11214-XXXX 3.000" 10,000psi 17.63" 8.3

11079-XXXX 3.375" 10,000psi 17.63" 10.5

11220-XXXX 3.875" 10,000psi 17.63" 14.5

11226-XXXX 4.500" 10,000psi 17.63" 15.0


Ad suffix "H" for H2S service


Weights quoted are approxmate

Minimum ID is subject to pin connection



CT Torque Thro’ QuickConnectThe Weatherford BDK Torque Thro' Quick Connect is a self aligningconnector and is designed to eliminate the problems of connecting the CoiledTubing when there is no means of rotating the Coiled Tubing or the BottomHole assembly. The inter-locking system allows the tool to experience highlevel of torque without any detrimental effects on the connector.

An optional Bleed-off Plug is incorporated in the lower section of the tool asan additional safety featureOnly 10 degrees of movement is required to line up the interlocking systemprior to make upCompact design for use on impact deck application

Robust DesignEasy to maintainQuick to use during deployment operations

Standard Coiled Tubing OperationsMilling applicationsFishing operationsImpact deck operationsToolstring deployments operations

®

Features

Benefits

Applications



CT Torque Thro’ Quick Connect

Assembly Outside Drift Minimum Weight Torsional Yield Torsional Yield

Number Diameter Diameter ID (kg) Standard (ft.lb) H2S (ft.lb)

12893-XXXX 1.750" 0.625" 0.655" 3.4 1063 773

12894-XXXX 2.125" 0.875" 0.905" 5.0 1816 1320

12895-XXXX 2.250" 1.000" 1.030" 5.3 2273 1653

12704-XXXX 2.875" 1.312" 1.375" 8.1 7300 5316

13114-XXXX 3.200" 1.875" 1.890" 7.7 6000 4363




264

Coil Tubing EquipmentMotorhead



CT Motorhead AssemblyThe Weatherford Motorhead AssemblyBDK® is designed to incorporatethe standard tools used in coiled tubing operations in one compactassembly.

A choice of top Connections is available for joining to the coiled tubing tothe motorhead assembly.The tool is supplied as standard with thread connections. Optional integralconnectors are available upon request. These can either be an outlineconnector such as the Grub Screw Connector or Grapple Style Connector,or an in-line type such as the Dimple-On or Roll-On Connector and allowthe operator to achieve a minimum make-up length.

Below the top connection is a cartridge stylewhich offers a dual safety system combined with the added

advantage of fast and efficient redress.Below the Double Flapper Check Valve is awhich offers a torque through facility and pump off release. To release,a drop ball is deployed which seats on the Bobbin, pressure is thenapplied to overcome the strength of the Shear Screws. Failure of theShear Screws causes the bobbin to move into the release positionallowing retrieval of the upper section, leaving a fish neck profileexposed for future retrieval of the lower section.The lower tool is a , designed as acirculating safety component within the Bottom Hole Assembly. Thedesign features a shear activated Ball Seat coupled with a Burst Disc.Should circulation be lost during a coiled tubing operation, an increasein applied pressure to the tubing will rupture the Burst Disc, allowingsufficient circulation to pump a ball. Pressure can then be applied toshear the Shear Screws and shift the piston to regain maximumcirculation.

The Shear Screws provide for quick and easy redress, being positionedsuch that they are readily accessible.

Both the Upper Shear Disc and the Circulating Sub Shear Disc arepositioned in a wet free zone, to obviate any effects from either flowingor well-bore fluids.

Double Flapper CheckValve,

Hydraulic Disconnect,

Dual Function Circulating Sub

Shear Screw Type

Shear Disc Type

Features

Shear Disc Shear Screw



Motorhead Assembly

Benefits

Applications

Specification Guide

Robust DesignReduced toolstring lengthCost effective

Standard coiled tubing operationsImpact deck operations

Body Diameter Make Up Length Shear Disc TypeAssembly Number

Shear Screw TypeAssembly Number

1.500" 18.50" 9746 111735

1.750" 18.50" 8941 111736

2.000" 21.00" 11103 111737

2.125" 21.00" 11140 111738

2.250" 22.66" 11106 111739

3.125" 26.86" 10594 111740

268

Coil Tubing EquipmentJoints and Stems



CT High Flow Knuckle JointThe Weatherford BDK High Flow Knuckle Joint provides a degree offlexibility within the Bottom Hole Assembly.The totally enclosed design makes this style of Knuckle Joint suitable for jarringproviding more support for compressive loads.The BDK High Flow Knuckle Joint has a large through bore for conveyingfluids.

Large ID for higher flow rate through toolSuitable for jarring applicationsAdds flexibility to the BHA in deviated wells

Robust DesignEasy to maintainManipulation of BHA

All coiled tubing operationsFishing Operations

®

Features

Benefits

Applications



CT High Flow Knuckle JointAssembly Part Outside Minimum Working Make Up Reach Weight

Number Diameter ID* Pressure Length (Kickover) (kg)

12088-XXXX 1.250" 0.312" 10,000psi 10.13" 10 deg 1.4

11733-XXXX 1.500" 0.500" 10,000psi 11.50" 10 deg 1.8

12086-XXXX 1.687" 0.500" 10,000psi 11.50" 10 deg 2.4

11302-XXXX 1.750" 0.750" 10,000psi 12.85" 10 deg 2.6

12090-XXXX 2.000" 0.750" 10,000psi 13.30" 10 deg 3.5

11307-XXXX 2.125" 1.125" 10,000psi 13.42" 10 deg 3.5

12505-XXXX 2.250" 1.000" 10,000psi 14.05" 10 deg 4.5

12283-XXXX 2.375" 1.000" 10,000psi 14.12" 10 deg 5

11753-XXXX 2.500" 1.000" 10,000psi 14.12" 10 deg 5.5

12216-XXXX 2.875" 1.125" 10,000psi 15.46" 10 deg 8.2

11403-XXXX 3.125" 1.125" 10,000psi 15.76" 10 deg 10.4




* Unless limited by connection

Add suffix "H" to assembly number for H2S service



CT Lead Filled StemThe Weatherford BDK Pump Thro' Lead Filled Stem provides extra weightper foot when compared with more conventional weight bar.

Removes residual curve from the coiled tubing when conducting complexfishing operationsGive additional length to the BHA for cementation & cleanoutoperationsAdds mass to the BHA for jarring operations

Robust DesignRemoves residual curve from coiled tubingGive BHA addition length & weight if required

All coiled tubing operationsFishing OperationsCementation operationsCleanout operations

®

Features

Benefits

Applications



CT Lead Filled StemAssembly Part Outside Minimum Drift Length Weight

Number Diameter ID* ID* (kg)13133-XXXX 1.812" 0.375" 0.312" 36" 11.4

13134-XXXX 1.875" 0.375" 0.312" 36" 12.2

13135-XXXX 2.125" 0.500" 0.438" 36" 15.1

13136-XXXX 2.250" 0.500" 0.438" 36" 21.2

13137-XXXX 2.875" 0.500" 0.438" 36" 33.0






Additional OD ad length configurations available on request



CT Straight JointThe Weatherford BDK Straight Joint/Weight Bar is used to add extramass to the Coiled Tubing String for various applications.The BDK Straight Joint/Weight Bar is manufactured with Box x Pinconnections and is available in various sizes.The Straight Joint offers the operator a means of removing the residualcurve of the Coiled Tubing at the bottom hole assembly.By straightening the bottom hole assembly the Coiled Tubing can passunrestricted through crossovers, landing nipples and other restrictionswithin the well bore.

Removes residual curve from the coiled tubing when conductingcomplex fishing operationsGive additional length to the BHA for cementation & cleanoutoperationsAdds mass to the BHA for jarring operations

Robust DesignLow maintenance costRemoves residual curve from coiled tubingGives BHA addition length & weight if required


®

Features

Benefits

Applications



CT Straight JointAssembly Part Outside Minimum Length Weight

Number Diameter ID* (kg)

4808-XXXX 1.250" 0.375" 30" 4.0

6086-XXXX 1.250" 0.375" 36" 4.8

6304-XXXX 1.250" 0.375" 48" 6.5

6329-XXXX 1.500" 0.625" 30" 5.1

4869-XXXX 1.500" 0.625" 36" 6.2

5990-XXXX 1.500" 0.625" 48" 8.5

12152-XXXX 1.687" 0.625" 36" 8.2

7419-XXXX 1.750" 0.905" 30" 6.1

5870-XXXX 1.750" 0.905" 36" 7.5

5871-XXXX 1.750" 0.905" 48" 10.2

7420-XXXX 2.000" 1.030" 30" 7.9

6087-XXXX 2.000" 1.030" 36" 9.7

4316-XXXX 2.125" 1.150" 36" 10.5

6088-XXXX 2.250" 1.220" 36" 12.2

6089-XXXX 2.375" 1.280" 36" 13.1

6090-XXXX 2.500" 1.400" 36" 14.0

5294-XXXX 2.500" 1.400" 48" 19.0

6091-XXXX 2.875" 1.780" 36" 16.4

6092-XXXX 3.125" 2.030" 36" 18.0

6093-XXXX 3.500" 2.280" 36" 22.2









CT Swivel JointThe Weatherford BDK Swivel Joint offers bearing assisted rotation whenmaking up the Bottom Hole Assembly in the riser.The swivel is bearing operated and smooth in operation and can beutilized in large deployment operations or where the coiled tubing toolsneed to be deployed.

Enclosed swivel to prevent well fluids effecting bearing assemblyAnti rotational roll pins to stop movement of BHA once deployedShort make up length for tool

Robust DesignEasy to maintainQuick to install and easy to operateEnclosed bearing system that reduces the maintenance


®

Features

Benefits

Applications



CT Swivel JointAssembly Part Outside Minimum Length Weight

Number Diameter ID* (kg)12448-XXXX 1.500" 0.375" 10.08" 1.5

7278-XXXX 1.750" 0.530" 12.13" 2.3

6845-XXXX 2.000" 0.780" 12.43" 2.7

7830-XXXX 2.125" 1.010" 12.68" 3.0

7939-XXXX 2.250" 1.125" 12.68" 3.2

6951-XXXX 2.500" 0.930" 14.40" 5.3

6554-XXXX 2.875" 1.040" 14.40" 7.0

10809-XXXX 3.875" 2.000" 16.38" 12.3








CT Torque Thro’ DoubleKnuckle JointThe Weatherford BDK Torque Thro' Double Knuckle Joint provides flexibilitywithin the Bottom Hole Assembly.The totally enclosed design makes this style of Knuckle Joint suitable fordownward jarring providing more support for compressive loads.The BDK Torque Thro' Double Knuckle Joint incorporates a unique polygonalinternal drive providing high torque capability.

High torque capacityMulti-shot manipulationsAdds flexibility to the BHA in deviated wells



®

Features

Benefits

Applications



CT Torque Thro’ Double Knuckle JointAssembly Part Outside Minimum Working Reach Torsional

Number Diameter ID* Pressure (Kickover) Yield (ft.lb)11974-XXXX 1.500" 0.500" 10,000psi 10 deg 430

12099-XXXX 1.687" 0.562" 10,000psi 10 deg 550

11979-XXXX 1.750" 0.625" 10,000psi 10 deg 600

11894-XXXX 2.000" 0.625" 10,000psi 10 deg 1000

11989-XXXX 2.125" 0.687" 10,000psi 10 deg 1200

13147-XXXX 2.250" 0.750" 10,000psi 10 deg 1400

11994-XXXX 2.500" 0.812" 10,000psi 10 deg 1950

13184-XXXX 2.875" 0.937" 10,000psi 10 deg 2950

11999-XXXX 3.125" 1.000" 10,000psi 10 deg 3940






Torsional capacity excludes connection



CT Torque Thro’ KickoverKnuckle JointThe Weatherford BDK Torque Thro' Kickover Knuckle Joint provides forcontrolled manipulation of the Bottom Hole Assembly.Pressure applied either by flowing through an orifice or after dropping a ball is

applied to the piston face causing the Knuckle Joint to kick-over.Anti rotation screws provide a torque thro' capability.

10 Degree manipulation of tool once activatedMulti-shot manipulationsAdds flexibility to the BHA in deviated wells

Robust DesignEasy to maintainManipulation of BHA up to 10 degrees


®

Features

Benefits

Applications



CT Torque Thro’ Kickover Knuckle Joint

Assembly Part Outside Minimum Working Maximum Kickover Torque Weight

Number Diameter ID* Pressure Angle Rating (ft.lb) (kg)

71052125-0001 2.125" 0.375" 10,000psi 10 deg 130 12

71052250-0001 2.250" 0.375" 10,000psi 10 deg 130 13.6








CT Torque Thro’ KnuckleJointThe Weatherford BDK Torque Thro' Knuckle Joint provides a degree offlexibility within the Bottom Hole AssemblyThe totally enclosed design makes this style of Knuckle Joint suitable for jarringproviding more support for compressive loads.The BDK Torque Thro' Knuckle Joint incorporates a unique polygonal internaldrive providing high torque capacity.

High torque capacityMulti-shot manipulationsAdds flexibility to the BHA in deviated wells



®

Features

Benefits

Applications



CT Torque Thro’ Knuckle JointAssembly Part Outside Minimum Working Make Up Reach Weight Torsional

Number Diameter ID* Pressure Length (Kickover) (kg) Yield (ft.lb)11944-XXXX 1.500" 0.500" 10,000psi 9.34" 10 deg 1.4 430

12234-XXXX 1.687" 0.562" 10,000psi 10.18" 10 deg 1.8 550

12489-XXXX 1.750" 0.625" 10,000psi 10.22" 10 deg 2.0 600

11954-XXXX 2.000" 0.625" 10,000psi 11.70" 10 deg 3.1 1000

12225-XXXX 2.125" 0.687" 10,000psi 12.19" 10 deg 3.7 1200

12496-XXXX 2.250" 0.750" 10,000psi 12.38" 10 deg 4.1 1400

11964-XXXX 2.500" 0.812" 10,000psi 13.46" 10 deg 5.3 1950

12215-XXXX 2.875" 0.937" 10,000psi 15.75" 10 deg 8.8 2950

11969-XXXX 3.125" 1.000" 10,000psi 15.56" 10 deg 9.7 3940






Torsional capacity excludes connection



CT Tungsten StemThe Weatherford BDK Pump Thro' Tungsten Stem provides extra weight perfoot when compared with the conventional weight bar. This Stem increasestoolstring momentum, improving the effectiveness of jarring operations.

Removes residual curve from the coiled tubing when conducting complexfishing operationsGive additional length to the BHA for cementation & cleanoutoperationsAdds mass to the BHA for jarring operations

Robust DesignRemoves residual curve from coiled tubingGive BHA addition length & weight if required


®

Features

Benefits

Applications



CT Tungsten StemAssembly Part Outside Minimum Drift Length Weight

Number Diameter ID* ID* (kg)

11605-XXXX 1.812" 0.375" 0.312" 36" 12.6

6330-XXXX 1.875" 0.375" 0.312" 36" 13.4

6331-XXXX 2.250" 0.500" 0.438" 36" 23.0

7014-XXXX 2.875" 0.500" 0.438" 36" 36.0







286

Coil Tubing EquipmentToolstring Centralizers



CT Bow Spring CentralizerThe Weatherford BDK Pump Thro' Bow Spring Centralizer is designed toassist in centralizing the coiled tubing BHA in large bore completion tubing.The Centralizer can be installed at any point within the coiled tubing BottomHole Assembly.This style of Centralizer provides a centralizing force whilst passing through arange of diameters.Springs can be designed to suit operator requirements.Any combination of BHA sizes and centralizing diameters are available.

Flexibility to pass through completion profilesCentralization of coiled tubing BHA

Robust DesignEasy to maintainBHA Centralization

All coiled tubing operationsMilling operationsDeviated operationsImpact deck operationsMemory PLT operations

®

Features

Benefits

Applications



CT Bow Spring Centralizer

Assembly Body Maximum Minimum Make Up Number Weight

Number OD OD ID* Length of Springs (kg)6981-XXXX 1.750" 9.000" 0.787" 34.38 6 4.9

10468-XXXX 2.000" 7.250" 1.000" 34.68" 6 6.1

13152-XXXX 2.125" 9.250" 1.000" 34.68" 6 6.7

6918-XXXX 2.250" 7.500" 1.155" 34.38" 6 7.7

8352-XXXX 2.375" 7.000" 1.155" 34.38" 6 8.0

6909-XXXX 2.500" 7.750" 1.405" 34.38" 6 9.1

7632-XXXX 3.125" 7.750" 1.405" 36.68" 6 11.7



Weights stated are approximate

Add suffix "H" to assembly for H2S service



CT Fluted CentralizerThe Fluted Centralizer is used to centralize the CoiledTubing BHA at points within the well bore where problems of centralizationare paramount.The design of the flutes allow maximum fluid by pass, past the Centralizerwhich is an advantage during milling applications were debris as to becirculated to surface.The Fluted Centralizer is available in any combination of toolstring andcentralizing diameter.

Weatherford BDK

Fluted flow path for removal of well & completion debrisCentralization of coiled tubing BHA


All coiled tubing operationsMilling applicationsDeviated operationsMemory PLT operationsFishing operations standards & heavy duty

®

Features

Benefits

Applications



CT Fluted CentralizerAssembly Body Fluted Overall Weight

Number OD OD Length (kg)8186-XXXX 1.500" 2.000" 6.0" 1.6

6150-XXXX 1.750" 2.000" 6.0" 1.9

6151-XXXX 1.750" 2.250" 6.3" 2.2

6152-XXXX 1.750" 2.500" 6.5" 2.6

6153-XXXX 1.750" 2.750" 6.8" 3.2

6718-XXXX 2.250" 2.500" 6.5" 2.9

6719-XXXX 2.250" 2.750" 6.8" 3.4

12536-XXXX 2.250" 2.875" 6.8" 3.6

6154-XXXX 2.250" 3.000" 7.0" 4.0

6155-XXXX 2.250" 3.250" 7.3" 4.8

6156-XXXX 2.250" 3.500" 7.5" 5.6

6157-XXXX 2.250" 3.750" 7.8" 6.6

6158-XXXX 2.250" 4.000" 8.0" 7.3

6714-XXXX 2.875" 3.250" 7.3" 4.8

6715-XXXX 2.875" 3.500" 7.5" 5.6

6716-XXXX 2.875" 3.750" 7.8" 6.6

6717-XXXX 2.875" 4.000" 8.0" 7.6

6159-XXXX 3.125" 4.250" 8.3" 7.1

6160-XXXX 3.125" 4.500" 8.5" 7.8

6161-XXXX 3.125" 4.750" 8.8" 8.6

6162-XXXX 3.125" 5.000" 9.0" 9.3

6163-XXXX 3.125" 5.250" 9.3" 10.2

6164-XXXX 3.125" 5.500" 9.5" 10.9

6165-XXXX 3.125" 5.750" 9.8" 12.0

6166-XXXX 3.125" 6.000" 10.0" 12.7




Alternative Body and Fluted OD on request



CT Non-Rotating CentralizerThe Weatherford BDK Non-Rotating Centralizer is installed in the toolstringwhere support and centralization are required.The non-rotating Centralizer allows the Bottom Hole Assembly to rotateindependently from the centralizing sleeve, reducing friction and toolstringwear.Centralizer Diameters can be manufactured to suit customer requirements.

Interchangeable sleeves for a wider selection of centralizationCentralization of coiled tubing BHA

Robust DesignEasy to maintainBHA CentralizationCost effective

All coiled tubing operationsMilling applicationsDeviated operationsMemory PLT operationsFishing operations

®

Features

Benefits

Applications



CT Non-Rotating Centralizer

Assembly Body Sleeve Minimum Overall Weight

Number OD OD ID* Length (kg)12582-2125-XXXX 1.750" 2.125" 0.625" 14.93" 5.2

12582-2250-XXXX 1.750" 2.250" 0.625" 14.93" 5.2

12582-2275-XXXX 1.750" 2.275" 0.625" 14.93" 5.2

12582-2375--XXXX 1.750" 2.375" 0.625" 14.93" 5.2

12582-2500-XXXX 1.750" 2.500" 0.625" 14.93" 5.2

12245-2250-XXXX 2.125" 2.250" 0.750" 17.25" 7.0

12245-2300-XXXX 2.125" 2.300" 0.750" 17.25" 7.0

12245-2500-XXXX 2.125" 2.500" 0.750" 17.25" 7.0

12245-2750-XXXX 2.125" 2.750" 0.750" 17.25" 7.0

12245-3250-XXXX 2.125" 3.250" 0.750" 17.25" 7.0

12245-3500-XXXX 2.125" 3.500" 0.750" 17.25" 7.0

8472-3000-XXXX 2.250" 3.000" 0.750" 17.25" 7.3

8472-3500-XXXX 2.250" 3.500" 0.750" 17.25" 7.3

8472-4000-XXXX 2.250" 4.000" 0.750" 17.25" 7.3




* Minimum ID may change dependent on connection type

Alternative sleeve OD on request



CT Slipover Spring CentralizerThe Weatherford BDK Pump Thro' Bow Spring Centralizer isdesigned to assist in centralizing the coiled tubing BHA in large borecompletion tubing.The Centralizer can be installed at any point within the coiled tubingBottom Hole Assembly.This style of Centralizer provides a centralizing force whilst passingthrough a range of diameters.Springs can be designed to suit operator requirements.Any combination of BHA sizes and centralizing diameters areavailable.

Flexibility to pass through completion profilesCentralization of coiled tubing BHA


All coiled tubing operationsMilling operationsDeviated operationsMemory PLT operations

®

Features

Benefits

Applications



CT Slipover Spring CentralizerAssembly Body Maximum Tool Slip-over Make Up Number Weight

Number OD OD Bore ID Diameter Length of Springs (kg)

7741-400 2.000" 4.000" 1.390" 1.375" 23.71" 6 1.3

7741-700 2.000" 7.000" 1.390" 1.375" 27.71" 6 1.3

5874-400 2.625" 4.000" 1.700" 1.687" 25.67" 6 2.6

5874-700 2.625" 7.000" 1.700" 1.687" 29.17" 6 2.6

12593-7630 3.100" 7.630" 21.80" 2.156" 30.40" 12 3.4



Add suffix "H" to assembly for H2S service

296

Coil Tubing EquipmentCheck Valves



CT Double Flapper CheckValve - CartridgeThe Weatherford BDK Double Flapper Check Valve, with Cartridge Inserts,offers dual safety system with a Low Pressure Elastomer Seal and has theadded advantage of fast and efficient redress with easy replacement of theflapper cartridge assemblies.

This style of flapper check valve can be utilized on low or high-pressureapplications.

This design allows optimum bore through the check valveDesigned for working in high & low-pressure wells

Robust DesignEasy to maintainEasy to install onto the coiled tubing bottom hole assemblyGood for high & low pressure applications

All standard Coiled Tubing OperationsMilling operationsFishing operationsMemory PLT operations

®

Features

Benefits

Applications



CT Double Flapper Check Valve - Cartridge

Full Assembly Cartridge Only Outside Tool Drift Working Test Make Up Weight

Number Assembly Number Diameter ID* Size* Pressure Pressure Length (kg)

7564-XXXX 7407 1.250" 0.312" 0.250" 10,000psi 12,000psi 12.00" 1.5

7558-XXXX 7571 1.500" 0.393" 0.312" 10,000psi 12,000psi 13.22" 3.4

4264-XXXX 6195 1.750" 0.711" 0.640" 10,000psi 12,000psi 16.10" 3.8

6794-XXXX 6195 2.000" 0.711" 0.640" 10,000psi 12,000psi 16.32" 4.8

9446-XXXX 9211 2.125" 0.840" 0.750" 10,000psi 12,000psi 15.56" 5.5

4274-XXXX 6196 2.250" 1.020" 0.937" 10,000psi 12,000psi 17.90" 6.1

12837-XXXX 6196 2.375" 1.020" 0.937" 10,000psi 12,000psi 17.90" 6.6

11058-XXXX 6197 2.875" 1.310" 1.250" 10,000psi 12,000psi 18.84" 9.8

4273-XXXX 6197 3.125" 1.310" 1.250" 10,000psi 12,000psi 18.84" 14.0

7273-XXXX 6197 3.500" 1.310" 1.250" 10,000psi 12,000psi 19.54" 15.6








CT Double Flapper CheckValve - IntegralThe Weatherford BDK Double Flapper Check Valve, with Integral Housing,offers a dual safety system that ensures against reverse flow within the CoiledTubing in the event of a BHA failure or sudden well pressure increase.

This style of flapper check valve can be utilized on low or high-pressureapplications.

This design allows optimum bore with metal-to-metal seal between theflapper and seatDesigned for working in high pressure wells

Robust DesignEasy to maintainEasy to install onto the coiled tubing bottom hole assemblyGood for high pressure applications

All standard Coiled Tubing OperationsMilling operationsFishing operationsMemory PLT operations

®

Features

Benefits

Applications



CT Double Flapper Check Valve - CartridgeAssembly Outside Tool Drift Working Test Make Up Weight

Number Diameter ID* Size* Pressure Pressure Length (kg)

5458-XXXX 1.250" 0.500" 0.437" 10,000psi 12,000psi 11.50" 1.3

5426-XXXX 1.500" 0.540" 0.468" 10,000psi 12,000psi 13.20" 2.1

5423-XXXX 1.750" 0.750" 0.687" 10,000psi 12,000psi 16.00" 3.9

5381-XXXX 2.000" 1.060" 1.000" 10,000psi 12,000psi 17.50" 5.1

6060-XXXX 2.125" 1.060" 1.000" 10,000psi 12,000psi 17.50" 5.5

5452-XXXX 2.250" 1.156" 1.093" 10,000psi 12,000psi 15.70" 5.8

5446-XXXX 2.500" 1.338" 1.275" 10,000psi 12,000psi 18.60" 7.6






302

Coil Tubing EquipmentDisconnect / Circulating Subs



CT Burst Disc CirculatingSubThe Weatherford BDK Burst Disc Sub is designed to regain circulation bymeans of over pressurizing a burst disc at a predetermined pressure.If during a coiled tubing operation circulation is lost through the BHA andcirculation is required to prevent differential collapse of the coiled tubing or toactivate the disconnect then the burst disc would be activated allowingcirculation through the coiled tubing.

Compact toolKnown burst value of burst disc

Enables circulation to be obtained up the coiled tubing annulusGives a circulation path through the coiled tubing to allow the ball to beseated on this disconnect

All coiled tubing operationsDeviated operationsMilling operationsFishing operationsCementation & cleanout operationsMemory PLT operations

®

Features

Benefits

Applications



CT Burst Disc Circulating Sub

Burst Disc SubAssembly Part Maximum Make Up Tool Tool Drift Weight

Number OD Length ID* Size* (kg)9298-XXXX 1.250" 5.12" 0.393" 0.312" 0.4

6097-XXXX 1.500" 5.50" 0.650" 0.590" 0.5

11150-XXXX 1.750" 5.40" 0.780" 0.720" 0.6

11152-XXXX 2.125" 5.90" 1.155" 1.095" 0.9

11154-XXXX 2.250" 6.00" 1.250" 1.187" 1.1





Burst Disc

Part Number Burst

Pressure

6099 1,000psi

11445 2,000psi

6100 3,000psi

11446 4,000psi

6101 5,000psi

12720 6,000psi

Description Part Number

Blank Plug 6259

Burst Ring Hold Down Ring 5067

Burst Ring Hold Down Screw 5068



CT Dual FunctionCirculating Sub - Shear DiscThe Weatherford BDK Dual Function Circulating & Burst Disc Sub isdesigned as a circulating safety component within the Bottom HoleAssembly.The Design features a Shear-Out Ball Seat coupled with a Burst Disc.Should circulation be lost during a Coiled Tubing operation, an increase inapplied pressure to the coiled tubing will burst the disc, which will regain asufficient circulation rate to pump a ball.Pressure can then be applied to the coiled tubing to shear the shearscrews and shift the piston to regain maximum circulation.The Dual Function Circulating Sub is available for any Outside Diameterwith or without Bursting Discs.

Compact toolKnown burst value of burst discKnown value of shear pins

Enables full radial circulation to be obtained up the coiled tubingannulusGives a circulation path through the coiled tubing to allow the ball to beseated on this disconnect


®

Features

Benefits

Applications



CT Dual Function Circulating Sub - Shear Disc

Assy Part Max Make Up Tool Drift Size Drop Ball Weight

Number OD Length (actual bore) Size (kg)12100-XXXX 1.500" 9.00" 0.187" (0.250") 0.375" 1.3

13153-XXXX 1.687" 9.00" 0.187" (0.250") 0.375" 1.7

12101-XXXX 1.750" 10.00" 0.312" (0.375") 0.437" 1.9

12102-XXXX 2.125" 10.56" 0.312" (0.375") 0.437" 3.0

12103-XXXX 2.250" 11.30" 0.437" (0.500") 0.563" 3.7

13154-XXXX 2.375" 11.30" 0.437" (0.500") 0.563" 4.1

12104-XXXX 3.125" 14.12" 0.875" (0.937") 1.000" 8.3




Unless specified Dual Function Circulating Sub supplied with 3000psi burst disc

Shear Discs are available from 2,000-5,000 psi

Unless specified a 3,000 psi shear disc is supplied as standard

Burst Disc

Part Burst

Number Pressure

6099 1,000psi

11445 2,000psi

6100 3,000psi

11446 4,000psi

6101 5,000psi

12720 6,000psi


Blank Plug 6259





CT Dual FunctionCirculating Sub - ShearScrewThe Weatherford BDK Dual Function Circulating & Burst Disc Sub isdesigned as a circulating safety component within the Bottom HoleAssembly.The Design features a Shear-Out Ball Seat coupled with a Burst Disc.Should circulation be lost during a Coiled Tubing operation, an increase inapplied pressure to the coiled tubing will burst the disc, which will regain asufficient circulation rate to pump a ball.Pressure can then be applied to the coiled tubing to shear the shearscrews and shift the piston to regain maximum circulation.The Dual Function Circulating Sub is available for any Outside Diameterwith or without Bursting Discs.

Compact toolKnown burst value of burst discKnown value of shear pins

Enables full radial circulation to be obtained up the coiled tubingannulusGives a circulation path through the coiled tubing to allow the ball to beseated on this disconnect


®

Features

Benefits

Applications



CT Dual Function Circulating Sub - Shear ScrewAssy Part Max Make Up Tool Drift Size Drop Ball Hydraulic Shear Screw Pressure No. of Weight

Number OD Length (actual bore) Size Area Diameter (2 Screws) Shear Screws (kg)9492-XXXX 1.500" 8.00" 0.187" (0.250") 0.375" 0.441 sq in 0.090" 1600psi 2 1.1

13119-XXXX 1.687" 7.97" 0.250" (0.312") 0.437" 0.742 sq in 0.090" 950psi 2 1.2

7161-XXXX 1.750" 7.97" 0.250" (0.312") 0.437" 0.742 sq in 0.090" 950psi 2 1.4

11156-XXXX 2.125" 9.50" 0.500" (0.530") 0.625" 1.227 sq in 0.150" 1,550psi 2 2.2

11158-XXXX 2.250" 9.50" 0.500" (0.530") 0.625" 1.227 sq in 0.150" 1,550psi 2 2.6

12842-XXXX 2.375" 9.50" 0.500" (0.530") 0.625" 1.227sq in 0.150" 1,550psi 2 2.9

11160-XXXX 3.125" 10.40" 0.625" (0.656") 0.750" 2.237 sq in 0.185" 1,275psi 2 5.0




Unless specified Dual Function Circulating Sub supplied with 3000psi burst disc

Burst Disc

Part Burst

Number Pressure

6099 1,000psi

11445 2,000psi

6100 3,000psi

11446 4,000psi

6101 5,000psi

12720 6,000psi


Blank Plug 6259





CT Hydraulic Disconnect Sub(Torque Thro’) - Shear DiscThe Weatherford BDK Hydraulic Disconnect Sub offers a torque throughpump-off release.Shear Discs of a known strength are installed in the tool. The Shear Discs arehoused in a wet-free zone, being isolated from both well fluids and the coiledtubing contents. To release, a drop ball is deployed which seats on the piston,pressure is then applied to overcome the strength of the Shear Discs.Failure of Shear Disc allows the piston to move into the release positionallowing retrieval of the upper section, leaving a standard GS Fish NeckProfile exposed for future retrieval of the lower section.

Ball activated release systemTorque resistant design

Robust DesignShear discs protected from well fluid contamination

Deviated coiled tubing operationsStandard coiled tubing operationsMemory PLT operationsCementation & cleanout operations

®

Features

Benefits

Applications



CT Hydraulic Disconnect Sub (Torque Thro’) - Shear DiscAssembly Max Make Up Tool Drift Size Drop Ball Fishing Working Weight Torsional Strength ft/lbs

Number OD Length (actual bore) Size Profile Pressure (kg) Standard (H2S)

12094-XXXX 1.500" 14.37" 0.312" (0.375") 0.437" 12137 10,000psi 1.8 1,030 (750)

12095-XXXX 1.750" 14.48" 0.437" (0.500") 0.562" 2" GS 10,000psi 3.0 1,200 (1,200)

13170-XXXX 2.000" 15.90" 0.437" (0.500") 0.562" 2" GS 10,000psi 4.0 2,610 (1,900)

13171-XXXX 2.125" 16.0" 0.437" (0.500") 0.562" 2" GS 10,000psi 4.6 3,090 (2,250)

11196-XXXX 2.250" 16.70" 0.593" (0.656") 0.750" 2.5" GS 10,000psi 5.0 3,580 (2,606)

6945-XXXX 2.875" 19.47" 0.937" (1.000") 1.062" 3" GS 10,000psi 9.0 4,790 (3,480)

12098-XXXX 3.125" 19.50" 1.062" (1.125") 1.187" 3.5" GS 10,000psi 11.8 8,410 (6,117)




Shear Disc supplied at 3000psi as standard (2000-5000psi available on request)

Torsional strength quoted without connection data



CT Hydraulic Disconnect Sub(Torque Thro’) - Shear ScrewThe Weatherford BDK Heavy Duty Disconnect provides an emergencyrelease for the Bottom Hole Assembly in the event of a stuck toolstring.The Hydraulic Disconnect is fitted below the flapper check valve assemblyand when activated will allow retrieval of the Coiled Tubing whilst maintaininga well control barrier this will leave a clear GS fish neck 'looking up' for futurefishing operations.The design incorporates unique interlocking fingers which when combinedwith the support given from the bobbin provides high torque and bendingcapability for the joint.

Ball activated release systemTorque resistant design

Robust DesignEasy to maintain


®

Features

Benefits

Applications

Shear Screw



CT Hydraulic Disconnect Sub (Torque Thro’) - Shear Screw

Assembly Part Maximum Make Up Tool Drift Size Drop Ball Fishing Working Weight

Number OD Length (actual bore) Size Profile Pressure (kg)11898-XXXX 1.250" 12.45" 0.219" (0.281") 0.312" 1.25" GS 10,000psi 1.4

11899-XXXX 1.500" 13.61" 0.312" (0.375") 0.437" 12137 10,000psi 1.8

11098-XXXX 1.750" 14.75" 0.437" (0.500") 0.562" 2" GS 10,000psi 3.0

12591-XXXX 2.000" 15.31" 0.437" (0.500") 0.562" 2" GS 10,000psi 4.0

12506-XXXX 2.125" 15.47" 0.437" (0.500") 0.562" 2" GS 10,000psi 4.6

11333-XXXX 2.250" 16.70" 0.595" (0.656") 0.750" 2.5" GS 10,000psi 5.0

12838-XXXX 2.375" 16.70" 0.595" (0.656") 0.750" 2.5" GS 10,000psi 5.9

12097-XXXX 2.875" 18.76" 0.937" (1.000") 1.125" 3" GS 10,000psi 9.0

12096-XXXX 3.125" 19.80" 1.062" (1.125") 1.187" 3.5" GS 10,000psi 11.8




** Calculated for 1 screw

Shear Screw InformationAssembly Part Hydraulic Shear Pin Release Pressure Torsional Strength ft/lbs

Number Area Dia Size (Qty) 1 x Screw** Brass (mild steel) Standard (H2S)11898-XXXX 0.248 sq in 0.115" (4) 1,653psi (2,338psi) 530 (500)

11899-XXXX 0.441 sq in 0.151" (4) 1,673psi (2,367psi) 1,030 (750)

11098-XXXX 0.691 sq in 0.151" (2) 1,070psi (1,510psi) 1,200 (1,200)

12591-XXXX 0.691 sq in 0.151" (2) 1,070psi (1,510psi) 2,610 (1,900)

12506-XXXX 0.691 sq in 0.151" (2) 1,070psi (1,510psi) 3,090 (2,250)

11333-XXXX 0.994 sq in 0.151" (6) 740psi (1,050psi) 3,580 (2,606)

12838-XXXX 0.994 sq in 0.151" (6) 740psi (1,050psi) 4,790 (3,480)

12097-XXXX 2.237" sq in 0.214" (2) 661psi (936psi) 8,410 (6,117)

12096-XXXX 3.097" sq in 0.214" (4) 476psi (674psi) 10,980 (7,895)



CT Shear ReleaseDisconnect Sub(Torque Thro’)The Weatherford BDK Shear Release Disconnect Sub offers torquethrough capability and a straight pull release.

Shear pins of a known strength are installed into the tool at surface ata predetermined rating.To release, a load is applied greater than that of the combined shearpin strength.Failure of shear pins allows instant retrieval of the upper section,leaving a standard fish neck profile exposed for future retrieval of thelower section.The BDK Shear Release Disconnect Sub is available with either anInternal or External fish neck.

No ball required to activate release sequenceInternal or external fishing neck profile can be manufacturedKnown shear rating for pull release

Easy to maintain whilst on locationGood for release in highly deviated wellsRobust & proven design


®

Features

Benefits

Applications

Internal Fish Neck External Fish Neck



CT Shear Release Disconnect Sub (Shear Thro’)External Fishing Neck

Assy Max Make Up Tool Tool Drift Fishing Number ofShearScrew Hyd Area on Weight Torque (ft/lbs)

Number OD Length ID* Size Profile Shear Screws Size Shear Screw (kg) 18-22RC (17/4PH)

12960-XXXX 1.750" 11.86" 0.750" 0.687" 1.375" 1 to 8 0.125" 1.038 sq in 2.2 1,200 (1,650)

13033-XXXX 2.125" 14.20" 1.031" 0.968" 1.750" 1-8 or 1-16 0.250" 1.701 sq in 3.4 2,600 (3,570)

5356-XXXX 2.250" 13.20" 1.031" 0.968" 1.750" 1-8 or 1-16 0.250" 1.701 sq in 5.2 2,750 (3,780)

13034-XXXX 2.875" 13.80" 1.405" 1.343" 2.312" 1-8 or 1-16 0.250" 2.641 sq in 5.9 3,510 (4,830)

Internal Fishing Neck

Assy Max Make Up Tool ID* Tool Drift Fishing Number ofShearScrew Hyd Area on Weight Torque (ft/lbs)

Number OD Length ID* Size Profile Shear Screws Size Shear Screw (kg) 18-22RC (17/4PH)

13375-XXXX 1.750" 11.86" 0.750" 0.687" 1.25" GS 1 to 8 0.125" 1.038 sq in 2.2 1,200 (1,650)

13376-XXXX 2.125" 14.20" 1.031" 0.968" 1.50" GS 1-8 or 1-16 0.250" 1.701 sq in 3.3 2,600 (3,570)

5361-XXXX 2.250" 13.20" 1.031" 0.968" 2.00" GS 1-8 or 1-16 0.250" 1.701 sq in 4.9 2,750 (3,780)

5443-XXXX 2.875" 13.80" 1.405" 1.343" 2.50" GS 1-8 or 1-16 0.250" 2.641 sq in 5.3 3,510 (4,830)

Shear Screw Information

Shear Screw Material Rating Material Rating

Size (lbs) x 1 (lbs) x 1

0.125" Mild Steel 580 Brass 410

0.250" Mild Steel 2,623 Brass 1,845

Ordering Information


Assembly number determines number of holes required for shear screws, material to be used and connection required

Assembly Number - XXXX indicates - 8 holes AISI4140 18-22 RC - Connection

Assembly Number/S - XXXX indicates - 8 holes 17-4PH H1150 - Connection

Assembly Number/D - XXXX indicates - 16 holes AISI 4140 18-22RC - Connection

Assembly Number/SD - XXXX indicates - 16 holes 17-4PH H1150 - Connection


Unless requested tools supplied in AISI 4140 18-22RC with 8 holes and requested connection

316

Coil Tubing EquipmentRunning and Pulling Tools



CT Flow Activated ExternalBDK Pulling ToolThe Weatherford BDK Flow Activated External BDK Pulling Tool is designed forrunning and retrieving downhole flow control components with external fishing necks.The tool offers a slimline option to the Heavy Duty Pulling Tool where severerestrictions in the completion tubular dictates the external pulling tool body diameter.To engage the External Pulling Tool, a sit down weight is required for automaticengagement onto the fishing profile whilst pulling in a latched position; the dogs aresupported within the skirt of the tool this allows the operator to continue heavy jarringwithout the fear of shearing the dogs.For surface operation the dog assembly has a finger grip to enable the tool to bemanually released from the fishing neck.To release the Flow Activated External Pulling Tool fluid is pumped through the coiledtubing at a set rate this then causes an internal pressure build up caused by the fluidflow going through an orifice placed in the pulling tool, this then releases the toolfrom the fish neck by re-tracking the dogs.All BDK Flow Release Tools are supplied with a High and Low Flow Rate Orifice andBlank Plugs.

Multi-functional operationFinger release at surfaceSlim body ODAll BDK Flow Release Pulling Tools are supplied with a bull end drilled withrecommended size orifice and an adaptor to accept customer specific orifices

Robust DesignInterchangeable orifice that enables the tool to be run with all sizes of coiledtubingEasy to test & re-dress on location

Standard fishing operationsHeavy duty fishing operationsFishing operations in small completion tubular

®

Features

Benefits

Applications



CT Flow Activated External BDK Pulling ToolAssembly Part Nominal Maximum Tool ID* Activation Make Up Flow Rate Orifice Weight

Number Size OD Excluding Orifice Pressure (psi) Length (bbls/min) Size (kg)11518-XXXX 1.250" 1.450" 0.312" 118 13.73" 0.562 1/4" NPT X 0.265" 1.5

11472-XXXX 1.500" 1.687" 0.312" 213 16.07" 0.560 3/8" NPT X 0.250" 2.5

11472-XXXX 1.500" 1.687" 0.312" 213 16.07" 0.700 3/8" NPT X 0.265" 2.5

12155-XXXX 2.000" 1.810" 0.312" 95 16.20" 0.377 3/8" NPT X 0.250" 3.3

12155-XXXX 2.000" 1.810" 0.312" 95 16.20" 0.501 3/8" NPT X 0.281" 3.3

11483-XXXX 2.000" 1.875" 0.312" 95 16.20" 0.377 3/8" NPT X 0.250" 3.3

11483-XXXX 2.000" 1.875" 0.312" 95 16.20" 0.501 3/8" NPT X 0.281" 3.3

11342-XXXX 2.500" 2.235" 0.531" 250 16.43" 0.478 3/8" NPT X 0.250" 5.0

11342-XXXX 2.500" 2.235" 0.531" 250 16.43" 0.780 3/8" NPT X 0.312" 5.0

11471-XXXX 3.000" 2.740" 0.531" 150 17.95" 0.497 3/8" NPT X 0.312" 7.8

11471-XXXX 3.000" 2.740" 0.531" 150 17.95" 0.755 3/8" NPT X 0.343" 7.8

11447-XXXX 3.000" 2.800" 0.531" 150 17.95" 0.598 3/8" NPT X 0.312" 7.8

11447-XXXX 3.000" 2.800" 0.531" 150 17.95" 0.755 3/8" NPT X 0.343" 7.8

11494-XXXX 4.000" 3.612" 0.531" 71 19.66" 0.414 1/2" NPT X 0.312" 12.1

11494-XXXX 4.000" 3.612" 0.531" 71 19.66" 0.647 1/2" NPT X 0.375" 12.1






Fkow Rate Figures are approximate



CT Flow Activated GSRunning/Pulling ToolThe Weatherford BDK Flow Activated GS Running/Pulling Tool is designedto locate in standard internal GS fish necks.To engage the GS Tool, a sit down weight is applied for automaticengagement into the profile.To release the Flow Activated GS tool fluid is pumped through the coiledtubing at a set rate this then causes an internal pressure build up caused bythe fluid flow going through an orifice placed in the nose of the GS, this thenreleases the tool from the fish neck by re-tracking the dogs.

Multi-functional operationFully enclosed springs to prevent debris from entering the toolHeavy-duty dogsAll BDK Flow Release GS Tools are supplied with a bull end drilledwith recommended size orifice and an adaptor to accept customerspecific orifices

Robust DesignInterchangeable orifice that enables the tool to be run with all sizes ofcoiled tubingEasy to test & re-dress on location

Standard fishing operationsHeavy duty fishing operationsCompletion component deployment

®

Features

Benefits

Applications



CT Flow Activated GS Running/Pulling ToolAssembly Part Nominal Maximum Tool ID Activation Make Up Flow Rate Orifice Weight

Number Size OD Excluding Orifice Pressure (psi) Length (bbls/min) Size (kg)9764-XXXX 1.500" 1.470" 0.312" 328 15.37" 0.472 0.219" 1.4

6255-XXXX 2.000" 1.850" 0.312" 355 14.50" 0.346 0.190" 2.7

6742-XXXX 2.500" 2.250" 0.531" 282 15.40" 0.509 0.250" 5.2

6307-XXXX 3.000" 2.710" 0.531" 266 15.70" 0.497 0.250" 8.5

6801-XXXX 3.500" 3.100" 0.531" 275 16.40" 0.503 0.250" 11.2

6778-XXXX 4.000" 3.600" 0.531" 255 17.30" 0.484 0.250" 15.0

6949-XXXX 5.000" 4.480" 1.500" 116 21.00" 0.717 0.375" 23.5

10623-XXXX 6.000" 5.500" 1.500" 172 24.06" 0.874 0.375" 33.9

7930-XXXX 7.000" 5.820" 1.500" 172 26.97" 0.874 0.375" 40.0








CT Flow Activated Heavy DutyPulling ToolThe Weatherford BDK Flow Activated Heavy Duty Pulling Tool is designed forrunning and retrieving down hole flow control components.The heavy duty pulling tool has installed a collet to give maximum contact withthe external fishing neck profile, for use in heavy duty jarring operations andfeatures a unique Fish Neck Cage between the Collet Fingers.The fish neck cage supports the fish neck, preventing any hang up on the Colletfingers in highly deviated wells. A full sleeve both supports the Collet and givesthe tool a clean profile.To engage the Heavy Duty External Pulling Tool, a sit down weight is required forautomatic engagement onto the fishing profile whilst pulling in a latched position;the dogs are supported within the skirt of the tool this allows the operator tocontinue heavy jarring without the fear of shearing the dogs.To release the Flow Activated Heavy Duty External Pulling Tool fluid is pumpedthrough the coiled tubing at a set rate this then causes an internal pressure buildup caused by the fluid flow going through an orifice placed in the pulling tool, thisthen releases the tool from the fish neck by re-tracking the dogs.All BDK Flow Release Tools are supplied with a high and Low Flow Rate OrificeBlank Plugs.

Multi-functional operationFish neck support cageAll BDK Flow Release Pulling Tools are supplied with a bull end drilledwith recommended size orifice and an adaptor to accept customerspecific orifices.

Robust DesignInterchangeable orifice that enables the tool to be run with all sizes of coiledtubingEasy to test & re-dress on location

Standard fishing operationsHeavy duty fishing operationsDeviated fishing operations

®

Features

Benefits

Applications



CT Flow Activated Heavy Duty Pulling ToolAssembly Part Nominal Maximum Tool ID* Reach Activation Make Up Flow Rate Orifice Weight

Number Size OD Excluding Orifice Pressure (psi) Length (bbls/min) Size (kg)13238-XXXX 1.250" 1.688" 0.312" 2.46" 328 15.36" 0.583 1/4" NPT X 0.236" 3.0

9895-XXXX 1.250" 1.688" 0.312" 2.48" 200 15.36" 0.566 1/4" NPT X 0.250" 3.0

9095-XXXX 1.500" 1.875" 0.312" 3.10" 328 16.30" 0.698 3/8" NPT X 0.250" 3.7

9095-XXXX 1.500" 1.875" 0.312" 3.10" 328 16.30" 0.881 3/8" NPT X 0.281" 3.7

8691-XXXX 2.000" 2.125" 0.375" 3.73" 234 19.74" 0.503 3/8" NPT X 0.250" 6.3

8691-XXXX 2.000" 2.125" 0.375" 3.73" 234 19.74" 0.692 3/8" NPT X 0.281" 6.3

7941-XXXX 2.500" 2.500" 0.500" 3.74" 160 19.29" 0.610 3/8" NPT X 0.281" 8.5

7941-XXXX 2.500" 2.500" 0.500" 3.74" 160 19.29" 0.780 3/8" NPT X 0.312" 8.5

8702-XXXX 3.000" 3.050" 0.50" 5.42" 233 21.72" 0.604 3/8" NPT X 0.281" 12.4

8702-XXXX 3.000" 3.050" 0.50" 5.42" 233 21.72" 0.767 3/8" NPT X 0.312" 12.4

9819-XXXX 4.000" 3.800" 0.709" 5.87" 114 22.60" 0.629 1/2" NPT X 0.344" 16.3

9819-XXXX 4.000" 3.800" 0.709" 5.87" 114 22.60" 0.755 1/2" NPT X 0.375" 16.3

11308-XXXX 4.000" 4.125" 0.709" 5.87" 114 22.60" 0.629 1/2" NPT X 0.344" 20.0

11308-XXXX 4.000" 4.125" 0.709" 5.87" 114 22.60" 0.755 1/2" NPT X 0.375" 20.0







324

Coil Tubing EquipmentFishing Tools



CT Centre SpearThe Weatherford BDK Center Spear is an adaptation of a standard wirelinespear that as been converted to run on coiled tubing, the spear can be designedand manufactured to meet all well parameters and can be manufactured with asmany barbs as required.

To ensure that circulation can be achieved the top sub of the spear as beenported to allow circulation whilst conducting the fishing operation if required.

Circulation sub at top of spearManufactured to clients requirements

Robust designSuitable for all sizes of coiled tubing

Fishing operations

®

Features

Benefits

Applications



CT Centre SpearAssembly Body Spear Overall Weight

Number OD OD Length (kg)13221-1500-XXXX 1.250" 1.500" 21.57" 1.3

13221-1750-XXXX 1.250" 1.750" 21.57" 1.3

13222-1625-XXXX 1.750" 1.625" 22.96" 2.1

13222-1750-XXXX 1.750" 1.750" 22.96" 2.1

13222-2000-XXXX 1.750" 2.000" 22.96" 2.1

13222-2250-XXXX 1.750" 2.250" 22.96" 2.1

13222-2500-XXXX 1.750" 2.500" 22.96" 2.1

13222-2750-XXXX 1.750" 2.750" 22.96" 2.1

13223-2375-XXXX 2.375" 3.000" 24.21" 3.9




Alternative Spear OD on request

Centre Spear with Finder Skirt

Assembly Body Finder OD Spear Overall Weight

Number OD OD OD Length (kg)12148-2125-1625-XXXX 1.750" 2.125" 1.625" 23.1 2.9

12148-2500-1625-XXXX 1.750" 2.500" 1.625" 23.1 2.9

11682-2500-1875-XXXX 2.125" 2.500" 1.875" 23.50" 3.7

11682-2750-2000-XXXX 2.125" 2.750" 2.000" 23.50" 3.7

11682-3000-2250-XXXX 2.125" 3.000" 2.250" 23.50" 3.7

11682-3250-2500-XXXX 2.125" 3.250" 2.500" 23.50" 3.7

11682-3500-2750-XXXX 2.125" 3.500" 2.750" 23.50" 3.7

12923-4500-4500-XXXX 3.125" 4.500" 4.500" 35.10" 10.4




Alternative Spear and Finder OD on request

Assembly number consists of : Drawing Number-Skirt OD-SpearOD-Connection



CT Flow Activated AlligatorGrabThe Weatherford BDK Flow Activated Alligator Grab is used to recoverdebris from within the completion / liner.To activate the Flow Activated Alligator Grab an internal pressure build upcreated by flowing fluid through the coiled tubing as the fluid reaches theorifice a back pressure is created and the Jaws open out.Once the jaws are activated the Alligator Grab is positioned over the debrisand the fluid flow rate is then relaxed at this point a heavy duty spring isfunctioned closing the jaws onto the debris.The jaws will remain closed until the flow rate is re-established.All BDK Flow Release Tools are supplied with a High and Low Flow RateOrifice and Blank Plugs.The Alligator Grab can be manufactured to any size

Various orifice settings for optimum performancePositive grip once activatedEasy to maintain

Robust designMulti operationalSuitable for all sizes of coiled tubing

Fishing operations

®

Features

Benefits

Applications



CT Flow Activated Alligator GrabAssembly Part Maximum Jaw OD Reach Activation Make Up Flow Rate Orifice Weight

Number OD Open Pressure (psi) Length (bbls/min) Size (kg)

12135-XXXX 2.000" 1.63" 2.46" 758 23.50" 0.42 2 x 0.125" 4.5

12135-XXXX 2.000" 1.63" 2.46" 758 23.50" 0.69 2 x 0.156" 4.5

12135-XXXX 2.000" 1.63" 2.46" 758 23.50" 1.09 2 x 0.187" 4.5

12135-XXXX 2.000" 1.63" 2.46" 758 23.50" 1.43 2 x 0.203" 4.5

12135-XXXX 2.000" 1.63" 2.46" 758 23.50" 1.94 2 x 0.219" 4.5

12136-XXXX 2.700" 2.15" 2.48" 716 27.70" 0.41 2 x 0.125" 9.2

12136-XXXX 2.700" 2.15" 2.48" 716 27.70" 0.67 2 x 0.156" 9.2

12136-XXXX 2.700" 2.15" 2.48" 716 27.70" 1.07 2 x 0.187" 9.2

12136-XXXX 2.700" 2.15" 2.48" 716 27.70" 1.39 2 x 0.203" 9.2

12136-XXXX 2.700" 2.15" 2.48" 716 27.70" 1.88 2 x 0.219" 9.2








CT Flow Activated InternalSpearThe Weatherford BDK

Robust Design

® Flow Activated Internal Spear is designed to fishcompletion components or toolstrings, which has damaged internal fishing necks, ortubular sections lost within the well bore.To engage the Flow Activated Internal Spear a sit down weight is required whenentering the component to be recovered, once the component has been engagedroutine fishing operations can commence.If during the fishing operation you need to release the Flow Activated Internal Spear allyou do is to start pumping fluid through the coiled tubing this then creates a backpressure over the tool which activates the release sequence.At this point the coiled tubing can be picked up and the Flow Activated Internal Spearwill be released from the fish.All BDK Flow Release Tools are supplied with a High and Low Flow Rate Orifice andblank plugs.

Various orifice settings for optimum performanceEasy to maintain

Multi operationalSuitable for all sizes of coiled tubing

Fishing operations

-

Features

Benefits

Applications



CT Flow Activated Internal Spear

Assembly Part Nominal Maximum Tool ID* Fishing Range Reach Make Up Flow Rate Orifice

Number Size OD Excl. Orifice Length (bbls/min) Size

11412-XXXX 2.000" 1.750" 0.218" 0.750" - 1.625" 3.00" 25.30" 0.648 not used

7855-XXXX 2.000" 1.850" 0.218" 0.750" - 1.625" 3.00" 25.30" 0.648 not used

11246-XXXX 2.250" 2.125" 0.375" 1.250" - 2.062" 3.53" 25.20" 0.667 - 0.912 0.250" - 0.281"

8057-XXXX 2.500" 2.250" 0.375" 1.250" - 2.062" 2.88" 25.30" 0.667 - 0.912 0250" - 0.281"

11409-XXXX 3.000" 2.562" 0.375" 1.750" - 2.375" 2.92" 25.60" 0.535 - 0.723 0.250" - 0.281"

8160-XXXX 3.000" 2.625" 0.375" 1.750" - 2.375" 3.00" 25.60" 0.535 - 0.723 0250" - 0.281"

8192-XXXX 3.500" 3.350" 0.562" 2.000" - 3.125" 4.17" 29.70" 0.544 - 0.698 0.281" - 0.312"

8370-XXXX 4.000" 3.800" 0.562" 2.000" - 3.562"" 4.49" 34.20" 0.770 0.312"

8431-XXXX 5.000" 4.150" 0.687" 2.375" - 3.875" 3.95" 30.90" 0.541 - 0.818 0.312" - 0.375"



2" Spear utilises different lower mandrels for 0.750" - 1.125" and 1.250" - 1.625"



Flow Rate Figures are based on fluid density of 7.928 lb/gal



CT Flow Activated OvershotThe Weatherford BDK Flow Activated Releasable Overshot is designed tofish by location on an external diameter.The Flow Release Overshot performs the same operation as the wirelineOvershot but is activated by flow and not by fracture of a shear pin.The bowl and collet slips are manufactured as interchangeable items allowingthe tool to be customized to suit a range of fishing diameters.The Overshot is operated by automatic latch on using sit down weight andreleased by a combination of reducing the sit down weight and increasing theflow through the tool.To release the Flow Activated Overshot fluid is pumped through the coiledtubing at a set rate this then causes an internal pressure build up caused bythe fluid flow going through an orifice placed in the nose of the Retrieval Tool,this then releases the tool from the fish neck by re-tracking the dogs.

Multi-functional operationManufactured to any current design of motorhead assemblyAll BDK Flow Release Pulling Tools are supplied with a bull end drilled withrecommended size orifice and an adaptor to accept customer specificorifices

Robust DesignInterchangeable orifice that enables the tool to be ran with all sizes ofcoiled tubingEasy to test & re-dress on location

Standard fishing operationsHeavy duty fishing operations

®

Features

Benefits

Applications



CT Flow Activated OvershotAssembly Part Nominal Maximum Tool ID* Collet Reach Make Up Flow Rate Orifice

Number Size OD Excluding Orifice Range Length (bbls/min) Size11433-XXXX 2.000" 1.750" 0.250" 0.437" - 1.312" 3.94" 18.14" 0.314 - 0.535 0.187" / 0.218"

7841-XXXX 2.000" 1.850" 0.250" 0.437" - 1.312" 3.94" 18.38" 0.314 - 0.535 0.187" / 0.218"

11234-XXXX 2.250" 2.125" 0.375" 0.687" - 1.562" 4.74" 19.54" 0.528 - 0.717 0.250" / 0.281"

7856-XXXX 2.500" 2.250" 0.375" 0.687" - 1.687" 4.74" 19.54" 0.528 - 0.720 0.250" / 0.281"

11406-XXXX 3.000" 2.562" 0.709" 0.937" - 2.062" 4.86" 24.52" 0.692 - 0.862 0.281" / 0.312"

8089-XXXX 3.000" 2.630" 0.750" 0.937" - 2.062" 4.90" 24.55" 0.692 - 0.862 0.281" / 0.312"

8429-XXXX 3.500" 3.350" 0.750" 1.312" - 2.687" 6.68" 28.40" 0.522 - 0.758 0.312" / 0.375"

5265-XXXX 3.500" 3.600" 0.750" 1.312" - 2.687" 6.69" 28.53" 0.522 - 0.759 0.312" / 0.375"

11263-XXXX 3.875" 3.750" 1.000" 1.562" - 3.062" 6.69" 28.68" 0.598 - 0.742 0.281" / 0.312"

8430-XXXX 4.000" 3.800" 1.000" 1.562" - 3.062" 6.71" 28.70" 0.598 - 0.743 0.281" / 0.312"

8066-XXXX 5.000" 4.150" 1.125" 1.812" - 3.562" 5.96" 26.50" 0.692 - 0.843 0.250" / 0.281"

8108-XXXX 7.000" 5.870" 1.000" 2.062" - 4.937" 6.23" 28.21" 0.830 - 1.088 0.218" / 0.250"






Flow Rate Figures are approximate



CT Flow Activated RetrievalTool (For Disconnect/Motorhead Assemblies)

The Weatherford BDK Flow Activated Retrieval Tool is a custom built tool toretrieve any style of Motorhead and Disconnect devices as specified by ourcustomer.

The BDK Flow Activated Retrieval Tool features fully enclosedsprings and heavy-duty dogs.

To engage the Retrieval Tool, a sit down weight is applied for automaticengagement into the profile.To release the Flow Activated Retrieval tool fluid is pumped through the coiledtubing at a set rate this then causes an internal pressure build up caused bythe fluid flow going through an orifice placed in the nose of the Retrieval Tool,this then releases the tool from the fish neck by re-tracking the dogs.All BDK Flow Release Tools are supplied with a High and Low Flow RateOrifice and Blank Plugs.

Multi-functional operationManufactured to any current design of motorhead assemblyAll BDK Flow Release Pulling Tools are supplied with a bull end drilled withrecommended size orifice and an adaptor to accept customer specificorifices

Robust DesignInterchangeable orifice that enables the tool to be ran with all sizes ofcoiled tubingEasy to test & re-dress on location

Standard fishing operationsHeavy duty fishing operations

®

Features

Benefits

Applications



CT Flow Activated Retrieval ToolFlow Activated Retrieval Tool for PSL Profile

Assy Part Maximum Tool ID* To Fish Reach Make Up Activation Flow Rate Orifice Weight

Number OD Excl. Orifice Length Pressure (bbls/min) Size (kg)9246-XXXX 2.250" 0.375" 2.375" PSL Profile 2.47" 22.90" 250psi 0.598 - 0.723 0.250" - 0.281" 7.2

9249-XXXX 2.265" 0.375" 2.875" PSL Profile 2.26" 25.60" 250psi 0.535 - 0.692 0.250" - 0.281" 10.2

Flow Activated Retrieval Tool for Petrotech ProfileAssy Part Maximum Tool ID* To Fish Reach Make Up Activation Flow Rate Orifice Weight

Number OD Excl. Orifice Length Pressure (bbls/min) Size (kg)

8916-XXXX 1.850" 0.281" 1.687" Petrotech Profile 4.13" 23.31" 250psi 0.440 - 0.755 0.218" - 0.250" 5.0








Weights quoted are approximate



CT Flow Activated VenturiJunk BasketThe Weatherford BDK Venturi Flow Activated Junk Catcher is designed toretrieve debris from within the well bore.This is achieved by circulating fluid through the coiled tubing which activates theventuri effect on the tool.The flow, which is directed via the jetting nozzles located in the upper section,creates a partial vacuum within the Flow Activated Junk Catcher and sucks thedebris through the lower non-return flapper system, which is then retained in thecatcher cylinder.The lower double flapper system will then retain the debris within the Catcher.The debris filter screen situated below the jetting system filters the fluids forcontinued circulation.The nozzles are interchangeable to enable the tool to function with differing flowrates.Extension catcher cylinders are available to increase the carrying capacity ofthe tool.

Manufactured to client’s specific requirementsThe nozzles are interchangeable to enable the tool to function with differingflow ratesExtension catcher cylinders are available to increase the carrying capacityof the tool

Robust DesignSuitable for all sizes of coiled tubing

Debris removal

®

Features

Benefits

Applications



CT Flow Activated Venturi Junk BasketAssembly Part Maximum Make Up Weight

Number OD Length (kg)

9777-XXXX 1.687" 42.81" 6.7

9777-02-XXXX 1.687" 68,81" 10.4

9777-03-XXXX 1.687" 80.81" 12.1

9777-04-XXXX 1.687" 92.81" 13.8

9777-05-XXXX 1.687" 106.81" 15.5

9777-06-XXXX 1.687" 116.81" 17.2

12417-XXXX 2.062" 44.26" 8.9

12417-02-XXXX 2.062" 70.26" 13.6

12417-03-XXXX 2.062" 82.26" 15.6

12417-04-XXXX 2.062" 94.26" 17.5

12417-05-XXXX 2.062" 106.26" 19.5

12417-06-XXXX 2.062" 118.26" 21.4

5216-XXXX 2.125" 44.02" 10.6

5216-02-XXXX 2.125" 70.02" 15.9

5216-03-XXXX 2.125" 82.02" 18.2

5216-04-XXXX 2.125" 94.02" 20.4

5216-05-XXXX 2.125" 106.02" 22.7

5216-06-XXXX 2.125" 118.02" 25.0

5388-XXXX 2.625" 48.08" 15.3

5388-02-XXXX 2.625" 74.08" 22.2

5388-03-XXXX 2.625" 86.08" 25.2

5388-04-XXXX 2.625" 98.08" 28.1

5388-05-XXXX 2.625" 110.08 31.0

5388-06-XXXX 2.625" 122.08 33.8

12710-XXXX 4.250" 48.08" 29.2

12710-02-XXXX 4.250" 74.08" 42.0

12710-03-XXXX 4.250" 86.08" 46.9

12710-04-XXXX 4.250" 98.08" 51.7

12710-05-XXXX 4.250" 110.08 56.6

12710-06-XXXX 4.250" 122.08 61.4



Weights quoted are approximate




CT Gauge CutterThe Weatherford BDK Gauge Cutter is used to gauge the tubing and toremove the scale, paraffin wax and debris etc., as well as ensuring theunhindered passage of subsequent Bottom Hole Assembly.This unique style of cutter has no hard edges and the protection cage helps inguiding the cutter as well as preventing damage to the cutting edge.Circulation can be achieved through the tool to remove debris during theoperation.

To ensure that circulation can be achieved the top sub of the spear as beenported to allow circulation whilst conducting the fishing operation if required.

Manufactured to clients requirementsProtection cage for centralizationProtection to gauge cutter edge


Wax removalTubular drifting

®

Features

Benefits

Applications



CT Gauge CutterAssembly Number Maximum OD

12278-01-XXXX 1.250"

12278-02-XXXX 1.500"

12278-03-XXXX 1.750"

12278-04-XXXX 2.000"

12278-05-XXXX 2.375"

12278-06-XXXX 2.875"





CT Lead Impression BlockThe Weatherford BDK Lead Impression Block is used to identify fishingnecks and debris during coiled tubing conveyed fishing operations and canbe manufactured to any size.

The Lead Impression Block as a circulation sub at the top, which will enablefluids to be pumped during the operation, the lead is protected with an outerskirt, which prevents damage whilst running into the completion tubular.

Manufactured to clients requirementsCirculation sub at top of LIBSkirt to protect lead whilst running in to locate fish


Fish identificationDebris identification

®

Features

Benefits

Applications



CT Lead Impression Block

Assembly Maximum Connection Overall Weight

Number OD OD Length (kg)

9291-1875-XXXX 1.875" 1.562" 9.17" 1.8

9291-2500-XXXX 2.500" 2.250" 9.87" 3.2

9291-2750-XXXX 2.750" 2.250" 10.00" 3.8

9291-3000-XXXX 3.000" 2.250" 10.13" 4.3

9291-3250-XXXX 3.250" 2.250" 10.25" 5.1

9291-3500-XXXX 3.500" 2.250" 10.38" 5.7

9291-3750-XXXX 3.750" 2.250" 10.50" 6.2

9291-4000-XXXX 4.000" 2.250" 10.75" 7.3

9291-4250-XXXX 4.250" 2.250" 10.87" 9.0

9291-4500-XXXX 4.500" 2.250" 11.00" 9.0

9291-4750-XXXX 4.750" 2.250" 11.13" 9.9

9291-5000-XXXX 5.000" 2.250" 11.25" 10.7

9291-5250-XXXX 5.250" 2.250" 11.38" 11.8

9291-5500-XXXX 5.500" 2.250" 11.50" 12.8

9291-5750-XXXX 5.750" 2.250" 11.75" 14.2

9291-6000-XXXX 6.000" 2.250" 11.87" 15.4

9291-6250-XXXX 6.250" 2.250" 12.00" 16.7

9291-6500-XXXX 6.500" 2.250" 12.23" 18.2

9291-6750-XXXX 6.750" 2.250" 12.25" 19.5

9291-7000-XXXX 7.000" 2.250" 12.38" 21.0






CT MagnetThe Weatherford BDK Coiled Tubing Magnet is a designed to retrieve smallmagnetically attractable metal items such as milling debris, nuts and boltswhich can cause problems within the completion tubular.The Magnet as circulation ports at the top to enable circulation through thecoiled tubing during the operation; the magnet is also protected with an outersleeve to ensure that any debris, which is collected, will not become dislodgedwhilst the coiled tubing is being retrieved to surface.

Manufactured to clients requirementsCirculation sub at top of MagnetSkirt to protect Magnet to ensure debris will not become dislodged


Removal of milling debrisRemoval of small metal particles

®

Features

Benefits

Applications



CT MagnetAssembly Maximum Connection Overall Weight

Number OD OD Length (kg)12207-2300-XXXX 2.300" 2.000" 13.25" 3.9

12207-2350-XXXX 2.350" 2.000" 13.27" 4.1

12207-2400-XXXX 2.400" 2.000" 13.30" 4.2

12207-2450-XXXX 2.450" 2.000" 13.32" 4.5

12207-2500-XXXX 2.500" 2.000" 13.35" 4.7

12207-2550-XXXX 2.550" 2.000" 13.37" 4.8

12207-2600-XXXX 2.600" 2.000" 13.40" 4.9

12207-2650-XXXX 2.650" 2.000" 13.43" 5.2

12207-2700-XXXX 2.700" 2.000" 13.45" 5.4

12207-2750-XXXX 2.750" 2.000" 13.48" 5.7

12207-2800-XXXX 2.800" 2.000" 13.50" 5.8

12207-2850-XXXX 2.850" 2.000" 13.53" 6.1

12207-2900-XXXX 2.900" 2.000" 13.55" 6.3

12207-2950-XXXX 2.950" 2.000" 13.58" 6.5

9314-3000-XXXX 3.000" 2.250" 14.02" 6.8

9314-3050-XXXX 3.050" 2.250" 14.05" 7.0

9314-3100-XXXX 3.100" 2.250" 14.07" 7.3

9314-3150-XXXX 3.150" 2.250" 14.10" 7.4

9314-3200-XXXX 3.200" 2.250" 14.12" 7.7

9314-3250-XXXX 3.250" 2.250" 14.15" 8.0

9314-3300-XXXX 3.300" 2.250" 14.17" 8.3

9314-3350-XXXX 3.350" 2.250" 14.20" 8.6

12922-3400-XXXX 3.400" 3.125" 14.65" 8.5

12922-3450-XXXX 3.450" 3.125" 14.68" 8.8

12922-3500-XXXX 3.500" 3.125" 14.70" 9.1

12922-3550-XXXX 3.550" 3.125" 14.73" 9.3

12922-3600-XXXX 3.600" 3.125" 14.75" 9.7

12922-3650-XXXX 3.650" 3.125" 14.78" 9.9

12922-3700-XXXX 3.700" 3.125" 14.80" 10.3

12922-3750-XXXX 3.750" 3.125" 14.83" 10.6

12922-3800-XXXX 3.800" 3.125" 14.85" 10.9

12922-3850-XXXX 3.850" 3.125" 14.88" 11.2

12922-3900-XXXX 3.900" 3.125" 14.90" 11.6

12922-3950-XXXX 3.950" 3.125" 14.93" 11.8

12922-4000-XXXX 4.000" 3.125" 14.95" 12.2

12922-4050-XXXX 4.050" 3.125" 14.97" 12.6

12922-4100-XXXX 4.100" 3.125" 15.00" 12.9

12922-4150-XXXX 4.150" 3.125" 15.03" 13.3

12922-4200-XXXX 4.200" 3.125" 15.05" 13.7

12922-4250-XXXX 4.250" 3.125" 15.08" 14.0

12922-4300-XXXX 4.300" 3.125" 15.10" 14.4

12922-4350-XXXX 4.350" 3.125" 15.13" 14.8

12922-4400-XXXX 4.400" 3.125" 15.15" 15.2

12922-4450-XXXX 4.450" 3.125" 15.18" 15.5

12922-4500-XXXX 4.500" 3.125" 15.20" 16.0

12922-4550-XXXX 4.550" 3.125" 15.23" 16.4





344

Coil Tubing EquipmentNozzles



CT Bull Nose Jetting NozzleThe Weatherford BDK Bull Nose Jetting Nozzles are available in single andmulti port designs.

The multi port nozzle is designed to give full radial coverage over the completiontubular during well intervention operations, the porting can be manufactured ineither side jet, down jet or up jet with the size of the jetting holes set to themaximum performance for each size of nozzle.

The single ported design as a hole bored through the centre for placement ofslurry during a shut off operation.These nozzles can also be manufacture with out any ports if requested.

Various porting scenarios for different applicationsFull radial coverage on multi-ported nozzleSingle port for placement applications


Standard Coiled Tubing OperationsCementation operationAcidization operations

®

Features

Benefits

Applications

SIDE JET

BLANK

DOWN JET

UP JET

DISPLACEMENT



CT Bull Nose Jetting NozzleAssembly Tool Hole Number Hole Overall

Number OD Pattern of Holes Diameter Length4938-XXXX 1.250" Blank 0 n/a 4.6"

4939-XXXX 1.250" Displacement 1 0.620" 4.6"

4940-XXXX 1.250" Side 4 0.190" 4.6"

4941-XXXX 1.250" Up Jet 4 0.190" 4.6"

4942-XXXX 1.250" Down 5 0.190" 4.6"

4943-XXXX 1.500" Blank 0 n/a 5.00"


4945-XXXX 1.500" Side 4 0.190" 5.00"

4946-XXXX 1.500" Up Jet 4 0.190" 5.00"

4947-XXXX 1.500" Down 5 0.190" 5.00"

4948-XXXX 1.750" Blank 0 n/a 5.40"


4950-XXXX 1.750" Side 4 0.190" 5.40"

4951-XXXX 1.750" Up Jet 4 0.190" 5.40"

4952-XXXX 1.750" Down 5 0.190" 5.40"

4953-XXXX 2.000" Blank 0 n/a 5.80"


4955-XXXX 2.000" Side 4 0.190" 5.80"

4956-XXXX 2.000" Up Jet 4 0.190" 5.80"

4957-XXXX 2.000" Down 5 0.190" 5.80"

4958-XXXX 2.125" Blank 0 n/a 6.00"


4960-XXXX 2.125" Side 4 0.190" 6.00"

4961-XXXX 2.125" Up Jet 4 0.190" 6.00"

4962-XXXX 2.125" Down 5 0.190" 6.00"

4963-XXXX 2.250" Blank 0 n/a 6.20"


4965-XXXX 2.250" Side 4 0.190" 6.20"

4966-XXXX 2.250" Up Jet 4 0.190" 6.20"

4967-XXXX 2.250" Down 5 0.190" 6.20"

4968-XXXX 2.375" Blank 0 n/a 6.30"


4970-XXXX 2.375" Side 4 0.190" 6.30"

4971-XXXX 2.375" Up Jet 4 0.190" 6.30"

4972-XXXX 2.375" Down 5 0.190" 6.30"

4973-XXXX 2.500" Blank 0 n/a 6.50"


4975-XXXX 2.500" Side 4 0.190" 6.50"

4976-XXXX 2.500" Up Jet 4 0.190" 6.50"

4977-XXXX 2.500" Down 5 0.190" 6.50"

6000-XXXX 2.750" Blank 0 n/a 7.30"


6002-XXXX 2.750" Side 4 0.190" 7.30"

6003-XXXX 2.750" Up Jet 4 0.190" 7.30"

5993-XXXX 2.750" Down 5 0.190" 7.30"



Nozzles are supplied in two materials - AISI 4140-18-22rc or 17-4PH H1550

Add suffix "S" for material 17-4PH H1550



CT Bull Nose Jetting Nozzle



Nozzles are supplied in two materials - AISI 4140-18-22rc or 17-4PH H1550

Add suffix "S" for material 17-4PH H1550

Assembly Tool Hole Number Hole Overall

Number OD Pattern of Holes Diameter Length

4979-XXXX 2.875" Blank 0 n/a 7.30"


4981-XXXX 2.875" Side 4 0.190" 7.30"

4982-XXXX 2.875" Up Jet 4 0.190" 7.30"

4983-XXXX 2.875" Down 5 0.190" 7.30"

6213-XXXX 3.000" Blank 0 n/a 7.50"


6215-XXXX 3.000" Side 4 0.190" 7.50"

6216-XXXX 3.000" Up Jet 4 0.190" 7.50"

6217-XXXX 3.000" Down 5 0.190" 7.50"

4984-XXXX 3.125" Blank 0 n/a 8.00"


4986-XXXX 3.125" Side 4 0.190" 8.00"

4987-XXXX 3.125" Up Jet 4 0.190" 8.00"

4988-XXXX 3.125" Down 5 0.190" 8.00"

4989-XXXX 3.500" Blank 0 n/a 8.60"


4991-XXXX 3.500" Side 4 0.190" 8.60"

4992-XXXX 3.500" Up Jet 4 0.190" 8.60"

4993-XXXX 3.500" Down 5 0.190" 8.60"

5612-XXXX 3.750" Blank 0 n/a 8.80"


5614-XXXX 3.750" Side 4 0.190" 8.80"

5615-XXXX 3.750" Up Jet 4 0.190" 8.80"

5616-XXXX 3.750" Down 5 0.190" 8.80"

5617-XXXX 4.000" Blank 0 n/a 9.30"


5619-XXXX 4.000" Side 4 0.190" 9.30"

5620-XXXX 4.000" Up Jet 4 0.190" 9.30"

5621-XXXX 4.000" Down 5 0.190" 9.30"

5622-XXXX 4.250" Blank 0 n/a 9.30"


5624-XXXX 4.250" Side 4 0.190" 9.60"

5625-XXXX 4.250" Up Jet 4 0.190" 9.60"

5626-XXXX 4.250" Down 5 0.190" 9.60"

5627-XXXX 4.500" Blank 0 n/a 10.00"


5629-XXXX 4.500" Side 4 0.190" 10.00"

5630-XXXX 4.500" Up Jet 4 0.190" 10.00"

5631-XXXX 4.500" Down 5 0.190" 10.00"

5632-XXXX 5.000" Blank 0 n/a 10.80"


5634-XXXX 5.000" Side 4 0.190" 10.80"

5635-XXXX 5.000" Up Jet 4 0.190" 10.80"

5636-XXXX 5.000" Down 5 0.190" 10.80"



SIDE JET

BLANK

DOWN JET

UP JET

DISPLACEMENT



CT Fluted Jetting NozzleThe Weatherford BDK Fluted Nozzles are available in single and multi portdesigns.

The Fluted Jetting Nozzle as been designed to allow well debris to past throughthe flutes during a cleanout operation and to give some centralisation to the BHA.






®

Features

Benefits

Applications

SIDE JET UP JET

DOWN JET

DISPLACEMENT

BLANK



CT Fluted Jetting NozzleAssembly Tool Hole Number Hole Overall

Number OD Pattern of Holes Diameter Length4994-XXXX 1.750" Blank 0 n/a 6.3"


5002-XXXX 1.750" Side 4 0.190" 6.3"

5003-XXXX 1.750" Up Jet 4 0.190" 6.3"

5004-XXXX 1.750" Down 5 0.190" 6.3"

5005-XXXX 2.000" Blank 0 n/a 6.7"


5007-XXXX 2.000" Side 4 0.190" 6.7"

5008-XXXX 2.000" Up Jet 4 0.190" 6.7"

5009-XXXX 2.000" Down 5 0.190" 6.7"

5010-XXXX 2.125" Blank 0 n/a 6.9"


5012-XXXX 2.125" Side 4 0.190" 6.9"

5013-XXXX 2.125" Up Jet 4 0.190" 6.9"

5014-XXXX 2.125" Down 5 0.190" 6.9"

5015-XXXX 2.250" Blank 0 n/a 7.0"


5017-XXXX 2.250" Side 4 0.190" 7.0"

5018-XXXX 2.250" Up Jet 4 0.190" 7.0"

5019-XXXX 2.250" Down 5 0.190" 7.0"

5020-XXXX 2.375" Blank 0 n/a 7.35"


5022-XXXX 2.375" Side 4 0.190" 7.35"

5023-XXXX 2.375" Up Jet 4 0.190" 7.35"

5024-XXXX 2.375" Down 5 0.190" 7.35"

5030-XXXX 2.500" Blank 0 n/a 7.40"


5032-XXXX 2.500" Side 4 0.190" 7.40"

5033-XXXX 2.500" Up Jet 4 0.190" 7.40"

5034-XXXX 2.500" Down 5 0.190" 7.40"

6004-XXXX 2.750" Blank 0 n/a 7.50"


6006-XXXX 2.750" Side 4 0.190" 7.50"

6007-XXXX 2.750" Up Jet 4 0.190" 7.50"

6008-XXXX 2.750" Down 5 0.190" 7.50"

5035-XXXX 2.875" Blank 0 n/a 7.90"


5037-XXXX 2.875" Side 4 0.190" 7.90"

5038-XXXX 2.875" Up Jet 4 0.190" 7.90"

5039-XXXX 2.875" Down 5 0.190" 7.90"



Add suffix "H" to assembly number for H2S Service

Cont..



CT Fluted Jetting Nozzle



Add suffix "H" to assembly number for H2S Service

Assembly Tool Hole Number Hole Overall


6218-XXXX 3.000" Blank 0 n/a 8.10"


6220-XXXX 3.000" Side 4 0.190" 8.10"

6221-XXXX 3.000" Up Jet 4 0.190" 8.10"

6222-XXXX 3.000" Down 5 0.190" 8.10"

5040-XXXX 3.125" Blank 0 n/a 8.20"


5042-XXX 3.125" Side 4 0.190" 8.20"

5043-XXXX 3.125" Up Jet 4 0.190" 8.20"

5044-XXXX 3.125" Down 5 0.190" 8.20"

5045-XXXX 3.500" Blank 0 n/a 9.00"


5554-XXXX 3.500" Side 4 0.190" 9.00"

5555-XXXX 3.500" Up Jet 4 0.190" 9.00"

5556-XXXX 3.500" Down 5 0.190" 9.00"

5575-XXXX 3.750" Blank 0 n/a 9.20"


5577-XXXX 3.750" Side 4 0.190" 9.20"

5578-XXXX 3.750" Up Jet 4 0.190" 9.20"

5579-XXXX 3.750" Down 5 0.190" 9.20"

5592-XXXX 4.000" Blank 0 n/a 9.70"


5594-XXXX 4.000" Side 4 0.190" 9.70"

5595-XXXX 4.000" Up Jet 4 0.190" 9.70"

5596-XXXX 4.000" Down 5 0.190" 9.70"

5597-XXXX 4.250" Blank 0 n/a 10.00"


5599-XXXX 4.250" Side 4 0.190" 10.00"

5600-XXXX 4.250" Up Jet 4 0.190" 10.00"

5601-XXX 4.250" Down 5 0.190" 10.00"

5602-XXXX 4.500" Blank 0 n/a 10.40"


5604-XXXX 4.500" Side 4 0.190" 10.40"

5605-XXXX 4.500" Up Jet 4 0.190" 10.40"

5606-XXXX 4.500" Down 5 0.190" 10.40"

5607-XXXX 5.000" Blank 0 n/a 11.20"


5609-XXXX 5.000" Side 4 0.190" 11.20"

5610-XXXX 5.000" Up Jet 4 0.190" 11.20"

5611-XXXX 5.000" Down 5 0.190" 11.20"



CT Mule Shoe NozzleThe Weatherford BDK Mule-Shoe Jetting Nozzles are available in single andmulti port designs

The Mule Shoe Jetting Nozzle as been designed to allow a lead in edge forentering through completion profiles.






®

Features

Benefits

Applications



CT Mule Shoe NozzleAssembly Tool Hole Number Hole Overall


03165-02-XXXX 1.250" Displacement 1 0.375" 3.87"

03165-03-XXXX 1.250" Down Jet 1 0.187" 3.87"

03165-01-XXXX 1.250" Side Jet 4 0.187" 3.87"

03165-XX-XXXX* 1.250" Up Jet tbc tbc 3.87"

03165-XX-XXXX* 1.250" Face Jet tbc tbc 3.87"


01726-02-XXXX 1.500" Down Jet 4 0.250" 4.90"

01726-03-XXXX 1.500" Side Jet 4 0.250" 4.90"

01726-04-XXXX 1.500" Up Jet 4 0.250" 4.90"

01726-07-XXXX 1.500" Face Jet 1 0.375" 4.90"


12817-XX-XXXX* 1.750" Down Jet tbc tbc 5.69"

12817-XX-XXXX* 1.750" Side Jet tbc tbc 5.69"

12817-XX-XXXX* 1.750" Up Jet tbc tbc 5.69"

12817-XX-XXXX* 1.750" Face Jet tbc tbc 5.69"


01668-04-XXXX 2.250" Down Jet 1 0.375" 12.00"

01668-02-XXXX 2.250" Side Jet 4 0.375" 12.23"

01668-03-XXXX 2.250" Up Jet 4 0.375" 12.25"

01668-05-XXXX 2.250" Face Jet 1 0.375" 12.38"



* Available on request



CT Multi-Jet Wash NozzleThe Weatherford BDK Multi-Jet Jetting Nozzle offers the versatility of aninterchangeable variable jetting orifice, this tool ensures that full tubular radiusare obtained during cleanout operations.

The Multi-Jet Jetting Nozzle is designed to allow the operator to set up the jettingsequence that best suit his and his client's requirements.

This is achieved by removing the blanking plugs and inserting the portedplugs for a specific application the hole size in the ports can be changed asrequired.

Various porting scenarios for different applicationsEasy to adjust porting arrangements

Robust DesignEasy to adjust for specific operations whilst on locationSuitable for all sizes of coiled tubing

Standard Coiled Tubing OperationsAcidization operations

®

Features

Benefits

Applications



CT Multi-Jet Wash Nozzle

Assembly Tool Number Hole Overall

Number OD of Holes Size Length8043-XXXX 1.750" 17 1/8" NPT 8.25"

8044-XXXX 2.000" 17 1/4" NPT 9.40"

8045-XXXX 2.125" 17 1/4" NPT 9.40"

8046-XXXX 2.250" 17 1/4" NPT 10.10"

8047-XXXX 2.375" 17 1/4" NPT 10.20"

8048-XXXX 2.500" 17 1/4" NPT 10.40"

8049-XXXX 2.875" 17 1/4" NPT 10.70"

8050-XXXX 3.125" 17 1/4" NPT 11.60"



Alternative sizes available on request

358

Coil Tubing EquipmentCementing Tools



CT Plug CatcherThe Weatherford BDK Plug Catcher is used to retain coiled tubing plugs inthe Bottom Hole Assembly (BHA) after cementation, acidization or cleaningoperations.The design allows the plug to be caught at the lower section of the PlugCatcher and allows the treatment that is being displaced to be positioned in acontrolled manner also giving a surface indication of the plugs being rupturedor bumped at surface during cementation operations.The Plug Catcher is available for any size of coiled tubing.

Plug indication once plug at BHAControlled Displacement

Robust DesignEasy to opereratePositive indication that the plug is on seat

Standard coiled tubing applicationsCementation operationAcidization operations

®

Features

Benefits

Applications



CT Plug LauncherThe Weatherford BDK Plug Launcher allows the insertion ofvarious styles of wiper/cementation plugs into the coiled tubing ina controlled manner.

The Plug Launcher incorporates a bleed off system to allow the coiledtubing isolation valve to be closed then inflow tested prior toremoving the top cap being removed for the plug installation.

Once the plug is inserted into the plug launcher the top cap is thenreplaced, whist this is being tightened the plug is being loweredinto position just below the fluid entry point for ease of injection ofthe plug into the coiled tubing.

Fully certifiedPressure bled facilityPlug location system

Robust DesignEasy to opereratePrevents damage to coiled tubing wiper / cementation plugsControlled installation

Standard coiled tubing applicationsCementation operationAcidization operations

®

Features

Benefits

Applications



CT Plug LauncherAssembly To Suit Connection Working Test Overall

Number plug Pressure Pressure Length

9168 50mm (1.968") 2" Weco 1502 10,000psi 15,000psi 14.75"

364

Coil Tubing EquipmentSurface Equiment



CT Surface Handling ToolThe Weatherford BDK Surface Handling Tool Assembly incorporatesan Internal Grapple Connector and is designed for guiding the CoiledTubing over the gooseneck and into the injector head whilst riggingup.The tool is designed with an internal coiled tubing grapple connectorthat covers a range of coiled tubing wall thickness for each size ofcoiled tubing, this ensures that one Surface handling tool will cover aselected coiled tubing size.Installation of the grapple is quick and easy, by removing the weldseam the grapple is then inserted into the coiled tubing than engagedby tightening the lock nut, this expands the grapple onto the wall ofthe coiled tubing.Once the coiled tubing is stabbed into the injector head the grapplecan be removed by un-screwing the lock nut.

Internal grapple that covers a wide range of coiled tubing wallthicknessLock nut to engage grapple for quick & easy installationCan be manufactured with a knuckle joint for added flexibility

Robust designReduces manual handlingReduces the amount of personnel required on the injector headReduces rig up timeAvailable in all coiled tubing sizes

To add the stabbing of the coiled tubing into the injector headduring rig up

®

Features

Benefits

Applications



CT Surface Handling ToolSurface Handling Tool - Standard

Part Number Coiled Tubing Size Coiled Tubing Wall Range

9518 1.250" 0.095" - 0.156"

9519 1.500" 0.095" - 0.175"

9520 1.750" 0.109" -0.188"

9521 2.000" 0.109" - 0.203"

9523 2.375" 0.109" - 0.203"

9525 2.875" 0.125" - 0.203"

9526 3.500" 0.134" - 0.203"

Surface Handling Tool - With Knuckle Joint

Part Number Coiled Tubing Size Coiled Tubing Wall Range

9909 1.250" 0.095" - 0.156"

9910 1.500" 0.095" - 0.175"

9911 1.750" 0.109" -0.188"

9912 2.000" 0.109" - 0.203"

9914 2.375" 0.109" - 0.203"

9916 2.875" 0.125" - 0.203"

9917 3.500" 0.134" - 0.203"



Tubing ClampThe Weatherford BDK is used to secure the coiled tubing atsurface and can be utilized in various coiled tubing applications.

Easy to install on to the coiled tubingCan be manufactured for all coiled tubing sizesEach clamp supplied with test load certification

Robust design

Tool-string deploymentSecuring coiled tubing in fishing operationsBack up to BOP slip rams

® Tubing Clamp

Features

Benefits

Applications



Tubing Clamp

Part Number CT Size

8439 1.250"

8801 1.500"

8802 1.750"

8803 2.000"

8826 2.375"

8827 2.875"

11734 3.500"



CT Tubing SnakeThe Weatherford BDK Coiled Tubing snake is utilized to manipulatethe coiled tubing into the injector head prior to making up the bottomhole assembly.

The coiled tubing snake is easy to install on to the coiled tubingCan be manufactured for all coiled tubing sizes

Robust DesignReduces manual handling required to install the coiled tubing intothe injector headReduced rig up time

Standard Coiled Tubing OperationsMilling applicationsFishing operationsImpact deck operationsCoiled tubing deployment into the injector head

®

Features

Benefits

Applications

Ferrule OptionStandard

bdk - coiled tubing equipment

Documents

service marks

property of weatherford

wcs coil tubing products

andindividual ct service

hole assembly products

ct surface equipment

different styles of

standard connectionthreads