bhm series backhoe - betstco

37
Rugged Labor Saving Equipment Since 1995 Betstco 83371 Melton Rd., Creswell OR 97426 OPERATION & PARTS MANUAL Please read these instructions carefully before using! Always grease all fittings and be sure to always check and fill with oil before operating! Retain this manual for future reference. Phone: 541-895-3083 www.betstco.com BHM SERIES BACKHOE

Upload: others

Post on 17-Feb-2022

4 views

Category:

Documents


0 download

TRANSCRIPT

Rugged Labor Saving Equipment Since 1995

Betstco83371 Melton Rd., Creswell OR 97426

OPERATION & PARTS MANUALPlease read these instructions carefully before using! Always grease

all fittings and be sure to always check and fill with oil beforeoperating! Retain this manual for future reference.

Phone: 541-895-3083www.betstco.com

BHM SERIES BACKHOE

2

TABLE OF CONTENTS

3

INTRODUCTION

Read the entire manual carefully before operating

Important

Serial Number and Location

Support Contact Information

4

SAFETY PRECAUTIONS1.1 SAFETYUnderstand that your safety and the safety of other persons is measured by how you service and operatethis Backhoe.

Know the position and operations of all controls before you operate. Make sure you check all controls insafe area before starting.

Read this manual completely and thoroughly and make sure you understand all controls. All equipment hasa limit. Make sure you are aware of the stability and load characteristics of this Backhoe before you beginoperation.

The Safety Information given in this manual does not replace any safety codes, insurance needs, federal,state and local laws. Make sure your machine has the correct equipment required by your local laws andregulations.

This safety alert symbol indicates important safety messages in this manual. When you seethis symbol, carefully read the message that follows and be alert to the possibility of personal injuryor death.

1.2 SAFETY PrecautionsBefore starting the engine of your tractor, make sure all operation controls are in park, lock or neutralposition.

Operate controls only when seated in the operator’s seat.

Equip your tractor with a ROPS cab or frame for your protection. See your tractor operator’s manual forcorrect usage.

A frequent cause of personal injury or death is persons falling off and being run over. Do not permit othersto ride on your tractor or backhoe. Only one person, the operator, should be on either machine when theyare in operation.

Before leaving the tractor or backhoe, stop the engine, put all controls in neutral, engage the parking brakeand remove the key from the ignition.

Operate the Backhoe smoothly when lowering or lifting loads.

Stay off of slopes too steep for safe operation. Shift down before you start up or down a hill with heavyload. Avoid "free wheeling”.

Travel speed should be such that complete control and machine stability is maintained at all times. Wherepossible, avoid operation near ditches, embankments and holes. Reduce speed when turning, crossingslopes, and on rough, slick or muddy surfaces.

5

SAFETY Precautions

ALWAYS CALL BEFORE YOU DIG!

6

7

8

9

3. VALUE-LEADER BHM BACKHOE SPECIFICATION

10

3. VALUE-LEADER BHM BACKHOE SPECIFICATION

11

4. TRACTOR PREPARATION

Caution: Do not exceed the manufacturer’s rating for maximum grossvehicle weight. Refer to Operator’s Manual Dealer, or Manufacture.

Caution: Certain Specific conditions may not permit safe use of backhoe atbackhoe rating or may require more careful restricted operation at the rated load.

4.1 ROPS System

4.2 Hydraulic SystemThe BHM Series Backhoe hydraulic system is powered by the tractors Power Take Off, and are fitted with anin-built Hydraulic pump, tank, and in-line filter system. Check fluid level daily, ensure PTO shaft is greasedand change hydraulic filter as required(refer to

BE SURE TO FOLLOW THE DETAILED STEPS OUTLINED IN ASSEMBLY &MOUNTING BEFORE USING THE BACKHOE!

Caution: The tractor / backhoe must only be operated with all safety equipmentproperly installed

4.3 Tire InflationFront Tires must be maintained at the maximum recommended inflation to maintain normal tire profile

Rear tires must be maintained at equal pressure within the recommended tire inflation range. Unequal reartire inflation can prevent backhoe attachment from controlling the ground across its full width.

4.4 Wheel Tread Settings

4.5 AttachmentEnsure your tractor’s 3 point linkage system is fitted with sway chains before attaching the backhoe.

4.6 Counter Weight

stability. Refer to tractor operator’ manual for specific recommendations on counter weighting tractor.

12

K

CAUTION: The tractor/backhoe should only be operated with all safetyequipment properly installed. Keep assistants or bystanders a safe distance fromthe equipment operating area.

5.1 Precautionary Notes:- Read and understand this manual to avoid accidents.- Check the hydraulic fitting lines to be correct and set tightly.- Maintain and repair (if it is needed) the parts or assemblies, check bolts and pins to be sure they

are positioned tightly.- Check tractor with the tractor operator’s manual that it can be prepared for operating.- Warm up and operate the tractor and backhoe carefully. Purge any air in the hydraulic lines and

cylinders by fully cycling all cylinders several times. Check the Fluid level in Tank each afterdoing this.

- Check hydraulic level in the tank to the specified level.- Do not operate the hydraulics when not seated in the backhoe operator’s seat.- Keep all assistants out of area of operation.- Do not operate rapidly.- Do not allow riders other than the operator to be on the tractor while operating.

ImportantUse tractor engine speed that your experience permits. At first set PTO RPM of the tractor to slow.Do not use the boom, dipper arm, swing or stabilizers to lift, push or pull objects. Use only to maneuverand operate the bucket.

ImportantPractice quickly turning off the engine or stopping the backhoe immediately in case of an emergency situation.

ImportantDo not operate while the rear tractor wheels are off the ground by stabilizer. It is dangerous to operate thebackhoe while rear wheels are off the ground.Position vehicle so that the backhoe is as near as possible and in such a direction as to minimize theamount of backhoe turning required to dump.Keep the unit clean and perform regular service.

13

5. BACKHOE OPERATION

We urge you to follow this advice: Failure to do so will result in a voidedwarranty, personal injury, or damage to equipment

Caution: When lowering a heavy load, ease it downward slowly. Never drop a loadedattachment and “catch it hydraulically”. Stopping a load after it has gained downloadmomentum places undue strain on the unit and may void your warranty, cause unnecessary damageto the backhoe/tractor or even worse, personal injury.

Caution: Before disconnecting hydraulic lines, relieve all hydraulic pressure. Escapinghydraulic oil under pressure can have sufficient force to penetrate the skin causing serious personalinjury. If injured by escaping hydraulic oil, seek medical attention immediately.

Caution: Do not operate the backhoe if the fittings are leaking or if the hoses aredamaged. A sudden line burst would cause the boom, or dipper arm bucket to dropsuddenly, void the warranty, cause damage to the tractor/backhoe or injury to personnel.

5.2 Initial Backhoe Operation

Check the tractor hydraulic oil and fill to the correct oil level

Caution: Before leaving the machine, stop the engine, remove the key. Place all controlsin neutral, and either set the parking brake or place tractor in park as equipped.

14

CAUTION:

15

5.4 Backhoe Hydraulic Controls

16

5.5 TRAVELING SWING AND BOOM LOCK

boom straight back and then slide pin through holes in boom & swing frame.

5.6 TRAVELING STABILIZER CLIP LOCKS

17

&

USE EXTREME CAUTION DURING CONNECTION TO TRACTOR

18

19

20

21

8.0 LUBRICATION AND MAINTENANCE

CAUTION: Do not perform service or maintenance Operations with backhoe raised off theground. For additional access to tractor components remove backhoe.

Important

CAUTION: Escaping fluid under pressure can have sufficient force to penetrate theskin, causing serious injury, before disconnecting lines, be sure to relieve all pressure.Before applying pressure to the system, be sure all connections are tight and that lines, pipes and hosesare not damaged. Fluid escaping from a very small hole can be almost invisible. Use a piece ofcardboard or wood rather than your hands to sear for suspected leaks. If injured by escaping fluid,seek medical attention immediately. Serious infection or reaction can develop if correct medicaltreatment is not administered immediately.

CAUTION: Do not operate the backhoe if any fittings are leaking or if the hoses aredamaged. A sudden line burst could cause the boom, dipper arm or bucket to dropsuddenly, causing damage to the tractor or backhoe or injury to personnel.

CAUTION: Operate the backhoe from the operator seat only .

CAUTION: Do not stand or walk under a raised backhoe. Accidental movement ofcontrol lever or leak in hydraulic system could cause boom or dipper arm to drop, causing severeinjury.

CAUTION: To help prevent roll-over, adjust the rear wheels to their widest setting tomaximize stability. Refer to your tractor Operator’s Manual for recommendations.

Tractor tires should be maintained at maximum recommended inflation to maintain normal tireprofile with added weight of backhoe/material. Unequal rear tire inflation can result in bucket not

22

9.0 TROUBLE SHOOTING

Trouble Shooting

23

9.0 TROUBLE SHOOTING9.0 TROUBLE SHOOTING

24

9.0 TROUBLE SHOOTING

25

9.0 TROUBLE SHOOTING

26

27

28

29

30

31

32

33

34

35

Value-Leader BrandLIMITED WARRANTY

Unless otherwise stated on purchase invoice, Betstco warrants to original Purchaser thatValue-Leader products are free from major defects in material under normal use and service for aperiod of Two (2) Years from the date the product is purchased or shipped, whichever is later.Commercial use 180 days. Use at address that is not yours, is considered commercial use.Consumable, Expendable, Wear Items (Examples:Rubber & plastic parts, hydraulic hoses, belts, tires,cables, blades, tines, wedges, teeth, tips, chains, pins, brushes, filters, etc.) and cracked hydraulic pumps,bent or broken cylinder rods are not covered under this warranty. Warranty does not cover items thathave been modified, damaged by abuse or usage not in accordance with design or maintenance.

Betstco obligation under this warranty is to repair or replace defective product uponapproval by; Betstco, 83371 Melton Rd. N., Creswell OR 97426 that Warranty Claim isValid. Product shall be returned upon request of Betstco. Transportation charges to beprepaid by buyer. Gasoline or diesel engines used to powered Value-Leader products arecovered by the warranty of the appropriate engine manufacture and Purchaser must look tothe engine manufacture for all issues relating to engine operation.

Betstco assumes no responsibility for outside labor.

PERMISSIBLE BY APPLICABLE LAW, BETSTCO HEREBY DISCLAIMS ALLWARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, ANY IMPLIEDWARRANTIES WITH RESPECT TO THE PRODUCT PURCHASED, WITHOUT LIMITING THEGENERALITY OF THE FOREGOING, BETSTCO HEREBY EXPRESSLY DISCLAIMSALL LIABILITY FOR PRODUCT DEFECT OR FAILURE, CLAIMS THAT ARE DUE TO NORMALWEAR, PRODUCT MISUSE, ABUSE, PRODUCT MODIFICATION, IMPROPER PRODUCTSELECTION, NON-COMPLIANCE WITH ANY CODES, OR MISAPPROPRIATION.•BETSTCO MAKES NO WARRANTIES TO THOSE DEFINED AS "CONSUMERS" IN THEMAGNUSON-MOSS WARRANTY-FEDERAL TRADE COMMISSION IMPROVEMENTS ACT . THEFOREGOING EXCLUSIONS OF IMPLIED WARRANTIES DO NOT APPLY TO THE EXTENTPROHIBITED BY LAW. PLEASE REFER TO YOUR LOCAL LAWS FOR ANY SUCH PROHIBITIONS

THERE SHALL BE NO LIABILITY FOR PRODUCT LIABILITY OR LIABILITY ON THE PARTOF BETSTCO FOR ANY GENERAL, SPECIAL OR CONSEQUENTIAL DAMAGESARISING OUT OF THE SALE OR USE OF ANY PRODUCTS SOLD BY BETSTCO OR ANAGENT THEREOF. BETSTCO MAKES NO WARRANTIES, EXPRESSOR IMPLIED, (INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITYOR FITNESS OF THE PRODUCTS FOR ANY PURPOSE) WITH RESPECT TO THE PRODUCTSCOVERED BY THIS AGREEMENT EXCEPT AS IN THIS PARAGRAPH OTHERWISE EXPRESSLYPROVIDED.

THIS IS THE SOLE AND ONLY WARRANTY OF Value-Leader PRODUCTS. NO OTHER WARRANTYIS APPLICABLE, EITHER EXPRESSED OR IMPLIED, IN FACT OR BY LAW,

This warranty shall not be interpreted to render Betstco, or any authorized agent liable forinjury or damages of any kind or nature, direct, consequential, or contingent, to person or property.

The sole and only remedy in regard to any defective products shall be the repair or replacement thereofas herein provided. Betstco, agent(s) of Betstco shall not be liable for anyconsequential, special, incidental or punitive damages resulting from or caused by any such defects.

Betstco reserves the right to make improvements in design or changes in specificationsat any time, without incurring any obligations to owners of units previously sold.No one is authorized to alter, modify, or enlarge this warranty nor the exclusions, limitations, andreservation thereof.

Value- Leader  1- 877- 876- 7895  [email protected] 12-12-13

36

Betstco / Pow’R’kraft  1‐877‐876‐7895  [email protected]

WARRANTY VOID IF REGISTRATION IS NOT RECEIVED OR RECORDED ONLINE WITHIN 30DAYS OF PURCHASE DATE OR SHIP DATE, WHICHEVER IS LATER.

VL REGISTRATION

Item________________________________Model # _________________ Purchase Date_____/_____/_______

Purchased From: ________________________________Gift □ Inv#/Order# ____________________________

Owner Name: _______________________________________ Serial # (if Applicable)______________________

Owner Address: _______________________________________

City: ________________________ County: ___________ ST: ______ Zip Code: _____________

Phone: _______________________ Email: ________________________

Acceptance of responsibility:I (Purchaser) have read operators manual and Limited Warranty or someone has read/and explained allinstructions to me. I understand this warranty does not cover any labor and that all disputes will be settled bybinding arbitration. Binding arbitration is conducted by the Better Business Bureau (BBB) located at 4004 SWKruse Way Place Ste 375 Lake Oswego OR 97035 or the current BBB location closest to Betstco, Iacknowledge my Limited Warranty is void if any attempt to repair or replace defective parts has been made byunauthorized personnel. I acknowledge receipt of my Operators Manual and have read the Safe OperationSection. I acknowledge understanding maintenance and safe operation requirements, item specifications,operation, controls, and storage requirements. I understand that I alone am responsible for propermaintenance, care and safe operation of this Value-Leader item.

I (Purchaser) agree that persons not familiar with the operation of this item should not be allowed to use it.Children especially should not operate or be near Power Products when in use. ANYONE OPERATINGVALUE-LEADER PRODUCTS SHOULD HAVE READ OPERATIONS MANUALS AND SAFETY MANUALS.

Owners Signature: x ____________________________________________ Date: ___/___/___

You must sign this warranty and mail or fax copy to Betstco, 83371 Melton Rd N.#3, Creswell OR97426. If you prefer you may complete your registration on line at www.Value-Leader.com. Thiswarranty is not effective unless the Purchaser completes Registration and Warranty Form within 30 daysof purchase or ship date whichever is later.

Fax to 1-541-895-2756

NOTE: We may refuse warranty of any kind unless Betstco, receives a completed, legible and signedwarranty registration. It is the responsibility of the purchaser to assure that registration document is received byBetstco.

Fax to 1-541-895-2756

Revised 10-16-13

37

2 YEAR EXTENDED WARRANTY & REGISTRATIONValue•Leader•Implement

Branded Products2 YEAR EXTENDED WARRANTY

2 Year Extended Warranty amends to original Recorded Warranty Registration thetime period of described coverage. Extended Warranty does not apply toConsumable and Expendable Items as described in Product Warranty Registration.This Amendment does not affect any other part of recorded Warranty Registrationor Policy.No one is authorized to alter, modify, or enlarge this Amendment to originalrecorded warranty registration.

EXTENDED REGISTRATION & PAYMENT MUST BE RECEIVEDWITHIN 30 DAYS OF PURCHASE DATE

EXTENDED WARRANTY REGISTRATIONProduct & Model # : ________________________________________Serial #: ______________________________Owner Name: _______________________________________Betstco Invoice # ________________________________Acceptance of responsibility:I (Purchaser) have Read and understand the Extended Warranty or someone has read/and explained allthe above to me. I understand this extended warranty does not cover any labor. I have filed my OriginalWarranty Registration and fully understand my requirements. I understand that I alone am responsiblefor proper maintenance, care and safe operation of this tractor implement.I (purchaser) also understand that persons not familiar with the operation of this equipment should not beallowed to use it. Children especially should not operate or be near equipment. ANYONE OPERATINGEQUIPMENT SHOULD HAVE READ ALL EQUIPMENT OPERATIONS MANUALS AND SAFETYMANUALS..Owners Signature: x ______________________________________________________Date: _________________You must sign this extended warranty and Fax to 1-541-895-2756 or mail copy to Betstco,

83371 Melton Rd N.#3, Creswell OR 97426. This extended warranty is not effective unless thePurchaser faxes or mails this Registration Form within 30 days of purchase. NOTE: TheManufacturer may refuse warranty of any kind unless Betstco receives a completed, legible andsigned extended warranty registration. It is the responsibility of the purchaser to assure that this registrationdocument is received by Betstco.

To Make Payment for Extended Warranty Call: 1-877-876-7895