bii 24451 fog lights - club rsx lights p/n 08v31-s6m-210 parts list right fog light left fog light...

16
© 2002 American Honda Motor Co., Inc - All Rights Reserved. BII 24451 (0209) 1 of 16 INSTALLATION INSTRUCTIONS Accessory Application Publications No. Issue Date SEP 2002 08V31-S6M-2001-91 2003 RSX FOG LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness Switch Templates 4 Step screws 2 Washer-screws 4 Spring nuts Relay Washer-bolt Cushion tape 21 Wire ties Left fog light BII 24451 4 Self-tapping screws, 5 x 16 mm (The end is not pointed.) 4 Self-tapping screws, 5 x 16 mm

Upload: duongxuyen

Post on 18-Mar-2018

225 views

Category:

Documents


4 download

TRANSCRIPT

Page 1: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

© 2002 American Honda Motor Co., Inc - All Rights Reserved. BII 24451 (0209) 1 of 16

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

SEP 2002

08V31-S6M-2001-91

2003 RSXFOG LIGHTSP/N 08V31-S6M-210

PARTS LIST

Right fog light

Left fog light trim

Right fog light trim

Left bracket

Right bracket

Switch harness

Fog light harness

Switch

Templates

4 Step screws

2 Washer-screws

4 Spring nuts

Relay

Washer-bolt

Cushion tape

21 Wire ties

Left fog light

BII 24451

4 Self-tapping screws, 5 x 16 mm (The end is not pointed.)

4 Self-tapping screws, 5 x 16 mm

Page 2: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

2 of 16 BII 24451 (0209) © 2002 American Honda Motor Co., Inc - All Rights Reserved.

FUSEBOX

SWITCH

RELAY

SWITCHHARNESS

RIGHTFOGLIGHT

LEFTFOGLIGHT

FOGLIGHTHARNESS

Wire tie with clip

2 Washers

Left sub-bracket

Right sub-bracket

Fuse label

TOOLS AND SUPPLIES REQUIREDPhillips screwdriver10 mm Combination wrenchRatchet10 mm SocketDiagonal cuttersDrill3 mm, 5 mm, and 10 mm Drill bitsHacksaw bladeUtility knifeScissorsPushpinMasking tapeFelt-tip pen

INSTALLATION

1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.

2. Disconnect the negative cable from the battery.

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These procedures shouldnot be attempted by “do-it-yourselfers.”

Illustration of Fog Lights Installed on the Vehicle

Page 3: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

© 2002 American Honda Motor Co., Inc - All Rights Reserved. BII 24451 (0209) 3 of 16

SMALLTEMPLATE

LARGETEMPLATES

MARK (3)

LARGE LEFTTEMPLATE

STRIP OFMASKING TAPE

FRONT BUMPER

PUSHPIN

LARGETEMPLATEUTILITY

KNIFE

PUSHPIN

FRONTBUMPER SMALL LEFT

TEMPLATE

TAB

SLIT MARKS (2)

Cutting the Front Bumper

3. Using scissors, cut out the templates. Fold bothsmall templates as shown.

6. Using a utility knife, score the bumper along theheavy line in the area shown. Remove the largetemplate from the bumper.

4. Position the large left template on the left bumpergrille, and tape it in position using masking tape.

7. Insert the two tabs of the small left template intothe slits in the front bumper. Using a pushpin,make a hole through each of the two marksindicated on the template.

Mark along the outeredge of the heavy line.

SMALLTEMPLATE

5. Using a pushpin, make a hole through each of thethree marks indicated on the template.

Fold.

Fold up.Foldhorizontally.

Page 4: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

4 of 16 BII 24451 (0209) © 2002 American Honda Motor Co., Inc - All Rights Reserved.

MARKS (5)

DRILL(First drill with a 3mm bit, then with a 5mm bit, and finishwith a 10 mm bit.)

DRILL(First drill with a 3 mm bit,then with a 5 mm bit, andfinish with a 10 mm bit.)

FRONT BUMPER

SCRIBED LINE

FRONTBUMPER

HACKSAW

FELT-TIPPEN

BOLTNUT

BATTERYHOLDER

CLIP

POSITIVECABLE BATTERY

CLIPSELF-TAPPINGSCREW

8. Remove the small template from the bumper.Using a 3 mm, 5 mm, and a 10 mm drill bit, drill ahole through each of the five marks.

Routing the Fog Light Harness

12. Disconnect the negative (–) and positive (+)cables from the battery, and release the clip fromthe holder bolt. Disconnect the negative (–) cablefirst.

9. Using a felt-tip pen, draw two straight linesacross the two upper adjacent 10 mm holes youjust made. Repeat on the lower pair of 10 mmholes.

10. Using a hacksaw or a utility knife, cut out theshaded areas for the fog light opening.

11. Position the right template on the right bumpergrille, and repeat steps 5 through 10 to cut out theright fog light opening.

13. Remove the bolt and the nut that fasten thebattery holder, and remove the holder and thebattery.

14. Remove the two self-tapping screws and one clip,then pull the left front inner fender out in thedirection shown. Repeat on the right front innerfender.

Draw two straight lines across thetwo lower adjacent 10 mm holes. LEFT

FRONTINNERFENDER

Draw two straight lines across thetwo upper adjacent 10 mm holes.

Do not cut.

Page 5: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

© 2002 American Honda Motor Co., Inc - All Rights Reserved. BII 24451 (0209) 5 of 16

RELAY BOX

HOLE

FOG LIGHTHARNESS 2-PINCONNECTOR(short end)

FOG LIGHTHARNESS

WINDSHIELDWASHERTANK FILLERNECK

FOG LIGHT HARNESS1-PIN CONNECTOR

VEHICLE HARNESS1-PIN CONNECTOR

BLUETAPE

BULKHEADUPPER FRAME

FOG LIGHTHARNESS 2-PINCONNECTOR(long end)

RIGHTHEADLIGHT

HOLEPOWER STEERINGFLUID RESERVOIR

FOG LIGHTHARNESS

15. Remove the windshield washer tank filler neckclip from its holder.

19. Route the fog light harness 2-pin connector (longend) along the vehicle harness behind the leftheadlight and inside of the bulkhead upper frametoward the right (passenger’s) side of the vehicle.Make sure the 2-pin connector is in front of thebulkhead center stay.

16. Locate the 1-pin connector blue-taped to thevehicle harness routed under the relay box, andremove the blue tape to free the connector.

17. Connect the 1-pin connector of the fog lightharness to the 1-pin connector of the vehicleharness you just freed.

18. Route the fog light harness 2-pin connector (shortend) down into the front bumper through the samehole as the windshield washer tank filler neck.

20. Remove the power steering fluid reservoir.Continue routing the fog light harness 2-pinconnector behind the right headlight along thevehicle harness, then hang it down into the frontbumper through the hole at the rear of the rightheadlight.

Route in front of thebulkhead center stay.

BRACKET

Page 6: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

6 of 16 BII 24451 (0209) © 2002 American Honda Motor Co., Inc - All Rights Reserved.

WIRE TIE

FOG LIGHT HARNESS1-PIN CONNECTOR

FOG LIGHTHARNESS

WIRE TIEBRACKET FOG LIGHT

HARNESS

WIRETIE

FOG LIGHTHARNESS

BULKHEADUPPER FRAME

WIRETIE

WIRE TIEWITH CLIP

WIRE TIERIGHT FRONTSIDE FRAME

FOG LIGHTHARNESS

LOWER CROSSMEMBER HOLE

WIRE TIE

VEHICLEGROUND BOLT(reused)

RIGHTFRONTINNERFENDER

LEFTFRONTINNERFENDER

FOG LIGHTHARNESSWIRE TIEWIRE TIE

LOWER CROSSMEMBER HOLE

21. Secure the fog light harness 1-pin connectorconnected behind the left headlight to the vehicleharness with one wire tie.

25. Pull out on the right front inner fender, and removethe vehicle ground bolt from the right front sideframe. Secure the ground terminal of the fog lightharness with this ground bolt.

26. Secure the fog light harness to the vehicleharness with two wire ties.

27. Secure the fog light harness to the hole in thelower cross member with one wire tie.

28. Pull out on the left front inner fender, and securethe fog light harness to the vehicle harness withthree wire ties.

22. Secure the fog light harness to the vehicleharness and the bracket on the left (driver’s) sideof the vehicle using three wire ties in the areasshown.

23. Secure the fog light harness to the hole in thebulkhead upper frame with the wire tie with clip.

24. Secure the fog light harness to the vehicleharness along the front bulkhead with three wireties.

29. Secure the fog light harness to the hole in thelower cross member and to the vehicle harnesswith one wire tie.

FOG LIGHT HARNESSGROUND TERMINAL(Secure the terminal tothe body ground at thefront of the vehicle.)

Page 7: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

© 2002 American Honda Motor Co., Inc - All Rights Reserved. BII 24451 (0209) 7 of 16

LEFT FOG LIGHT

WASHERSTEPSCREW

LEFTBRACKET

WASHER-SCREW

5 x 16 mm SELF-TAPPING SCREW(The end is not pointed.)

LEFT FOG LIGHTLEFTBRACKET

RUBBER WASHER(Discard.)

STEPSCREW

LEFTSUBBRACKETSLOT

LEFT FOGLIGHT TRIM

Installing the Fog Lights

30. Position the left bracket on the left fog light, andinstall one step screw with washer and onewasher-screw. Tighten both screws securely.

31. Install the left fog light onto the left fog light trim:

• Remove and discard the rubber washer fromthe step screw.

• Fit the tab on the left subbracket into the slot inthe left fog light trim, and install the step screw.Don’t tighten the step screw yet.

• Install two 5 x 16 mm self-tapping screwsthrough the left bracket and into the left foglight trim.

• Tighten the step screw.

NOTE: Before installing the bracket, check theidentification mark: The bracket marked “L” goeson the left side, the bracket marked “R” goes onthe right side.

Page 8: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

8 of 16 BII 24451 (0209) © 2002 American Honda Motor Co., Inc - All Rights Reserved.

32. Slide two spring nuts onto the bumper throughthe slits.

FOG LIGHT HARNESS2-PIN CONNECTOR

FRONTBUMPER

FOGLIGHT

5 x 16 mmSELF-TAPPINGSCREW

SLIT

SPRINGNUT

35. Inside the vehicle, turn the two knobscounterclockwise, and remove the driver’sdashboard lower cover (two retaining tabs andtwo hooks).

36. Turn the knob clockwise, and remove the driver’sdashboard under cover from the holder (one clip).

DRIVER’SDASHBOARDLOWER COVER

KNOB

RETAININGTABS (2)

HOOKS (2)

HOLDER

DRIVER’SDASHBOARDUNDER COVER

CLIP

KNOB

33. Pull the fog light harness 2-pin connector out, andconnect it to the left fog light. Position the left foglight assembly on the front bumper, and installtwo 5 x 16 mm self-tapping screws. Tighten thescrews securely.

34. Repeat steps 30 through 33 to install the right foglight.

Page 9: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

© 2002 American Honda Motor Co., Inc - All Rights Reserved. BII 24451 (0209) 9 of 16

37. Pull the center lower cover toward you to releasethe one retaining tab and six clips.

38. Unplug the vehicle 2-pin connector from theaccessory socket, and remove the center lowercover.

39. On M/T vehicles, push the boot down whileholding the plastic clip. Remove the shift knob byturning it counterclockwise.

41. Remove the center console trim by lifting it upwardto release the six clips and one retaining tab.

CENTER LOWERCOVER

CLIPS (6)

RETAINING TAB

BOOT

SHIFT KNOB

PLASTICCLIP

40. On A/T vehicles, remove the shift indicator trimring from the center console (four retaining tabs).

CENTERCONSOLETRIM

RETAININGTAB

CLIPS (6)

SHIFT INDICATORTRIM RING

RETAININGTABS (4)

CENTERCONSOLE

ACCESSORYSOCKET

VEHICLE 2-PINCONNECTOR

Page 10: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

10 of 16 BII 24451 (0209) © 2002 American Honda Motor Co., Inc - All Rights Reserved.

44. Inside the center console, remove the two clips.At the rear of the center console, remove the twoscrews.

42. Remove the two self-tapping screws that fastenthe center console.

CENTERCONSOLE

SELF-TAPPINGSCREW

43. Remove the beverage holder by lifting it upward torelease the four clips.

BEVERAGEHOLDER

CLIPS (4)

CENTERCONSOLE

SCREW

CLIPS (2)

CLIP

CENTERCONSOLE

SCREW

CLIPS (2)

CLIP

CENTERCONSOLE

SELF-TAPPINGSCREW

ACCESSORYSOCKET

VEHICLE 2-PINCONNECTOR

ACCESSORYSOCKET

VEHICLE 2-PINCONNECTOR

M/T Vehicles:

A/T Vehicles:

45. Release the two clips that secure the front of thecenter console, then disconnect the vehicle 2-pinconnector from the accessory socket by firstsliding the center console toward the rear, thenlifting it upward.

SCREW

SCREW

Page 11: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

© 2002 American Honda Motor Co., Inc - All Rights Reserved. BII 24451 (0209) 11 of 16

46. Remove the two self-tapping screws and onescrew, and remove the steering column upper andlower covers (six retaining tabs).

47. From behind the instrument panel, remove theright switch cover (two retaining tabs).

Push in.

STEERINGCOLUMNLOWERCOVER

SCREWSELF-TAPPINGSCREW

STEERING COLUMNUPPER COVER

RETAINING TABS (6)

SWITCHCOVER(Discard.)

RETAININGTABS (2)

INSTRUMENT PANEL

Routing the Switch Harness

48. Remove the bolt that secures the fuse box, andlower the fuse box.

49. Unplug the vehicle 6-pin connector from the fusebox, then plug the 6-pin connector of the switchharness there. Plug the 1-pin connector (WHT/REDwire) of the switch harness into the fuse box asindicated.

NOTE: On M/T vehicles, there is no 6-pinconnector plugged into the fuse box.

50. On A/T vehicles, locate the 6-pin connector tapedto the switch harness, and remove the dummyconnector from that connector. Plug the vehicle6-pin connector you just unplugged from the fusebox into that connector.

FUSE BOX

VEHICLE 6-PINCONNECTOR(A/T vehicles only)

SWITCH HARNESS1-PIN CONNECTOR(WHT/RED WIRE)

SWITCHHARNESS 6-PINCONNECTOR

SWITCHHARNESS

FUSE BOX

Location of 6-pin Connector

BOLT

Location of 1-pinConnector

Page 12: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

12 of 16 BII 24451 (0209) © 2002 American Honda Motor Co., Inc - All Rights Reserved.

55. Above the steering column, disconnect the vehicle16-pin connector. Remove the retainer, and insertthe switch harness terminal into the 16-pinconnector at the location shown. Reinstall theretainer.

56. Reconnect the vehicle 16-pin connector.

If the vehicle is equipped with an optional cigarettelighter, plug the switch harness 6-pin connector into thecigarette lighter 6-pin connector.

51. Reinstall the fuse box.

52. Locate the 1-pin connector blue-taped to thevehicle harness in front of the fuse box, andremove the blue tape to free the connector. Plugthe remaining 1-pin connector of the switchharness into this 1-pin connector.

CIGARETTE LIGHTERHARNESS

SWITCHHARNESS

FUSE BOX 6-PINCONNECTOR

STEERINGSHAFT

SWITCH HARNESS5-PIN CONNECTOR(Route to the switchlid opening.)

TERMINAL END ofSWITCH HARNESS(Route to the top of thesteering column.)

VEHICLEHARNESS

SWITCH HARNESS1-PIN CONNECTOR

BLUETAPE

VEHICLE HARNESS1-PIN CONNECTOR

FUSE BOX

SWITCH HARNESS

53. Route the 5-pin connector of the switch harnessunder the steering shaft to the switch opening inthe instrument panel.

54. Route the terminal end of the switch harness to thetop of the steering column along the vehicle harness.

RETAINERVEHICLE 16-PINCONNECTOR

SWITCH HARNESSTERMINAL(Insert into the 16-pinconnector with the stakedside facing down.)

SWITCHHARNESS

TERMINAL(for connecting theterminal of theswitch harness)

As Viewed fromthe Harness Side

Page 13: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

© 2002 American Honda Motor Co., Inc - All Rights Reserved. BII 24451 (0209) 13 of 16

57. Route the switch harness 12-pin connector to thecenter console opening alongside the vehicleharness.

SWITCH HARNESS12-PIN CONNECTOR

VEHICLEHARNESS WIRE TIE

VEHICLEHARNESS12-PINCONNECTOR

SWITCHHARNESS

CENTERCONSOLEOPENING

VEHICLE HARNESS12-PIN CONNECTOR

HOLDER

SWITCH HARNESS12-PIN CONNECTOR

58. At the center console opening, disconnect thevehicle 12-pin connector, then slide the 12-pinconnector of the switch harness onto the holder onthe side of the vehicle 12-pin connector.

59. Connect the vehicle harness 12-pin connectors tothe switch harness 12-pin connectors.

60. Secure the switch harness to the vehicle harnesswith one wire tie in the area shown.

61. Attach the fuse label (20A) to the switch harnessfuse case.

RELAY

62. Position the relay on the steering hanger beam,and install the washer-bolt. Plug the switchharness 4-pin connector into the relay.

SWITCHHARNESS4-PINCONNECTOR

STEERING HANGERBEAM

SWITCH HARNESSFUSE CASE

FUSE LABEL(20A)

SWITCHHARNESS

WASHER-BOLT

Page 14: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

14 of 16 BII 24451 (0209) © 2002 American Honda Motor Co., Inc - All Rights Reserved.

67. Check that all wire harnesses are routed properlyand all connectors are plugged in.

68. Reinstall all removed parts.

69. Reconnect the negative cable to the battery, andreset the radio station presets.

NOTE: Whenever the battery is disconnected, thedriver's window AUTO function is disabled.

70. Start the engine. Push down on the driver'swindow switch until the window is fully open.

71. Pull up on the driver's window switch to close thewindow completely, then hold the switch for asecond or two more.

72. Test the AUTO window function.

73. Do the ECM/PCM idle learn procedure.

• Make sure all electrical items are turned off.

• Start the engine. Hold the engine speed at3,000 rpm with no load (in Park or Neutral) untilthe radiator fan comes on.

• Let the engine idle for about 5 minutes with thethrottle fully closed and with all electrical itemsoff.

NOTE: If the radiator fan comes on during thisstep, the time it is operating must not beincluded in the 5 minutes.

63. Pull the switch harness 5-pin connector outthrough the instrument panel.

64. Secure the switch harness to the vehicle harnesswith six wire ties in the areas shown.

65. Plug the switch harness 5-pin connector into therear of the switch.

66. Install the switch into the instrument panel.

SWITCH

INSTRUMENTPANEL

SWITCHHARNESS5-PINCONNECTOR

WIRE TIE

SWITCHHARNESS

VEHICLEHARNESS

WIRETIE

SWITCH HARNESS5-PIN CONNECTOR

USE AND CARE

How to Operate the Fog Lights

• Turn the light switch to the “ ” or “ ” position(headlights on low beam).

• Press the fog light switch (indicator is on).

NOTE: The fog light lenses can cloud when theoutside temperature is cold; this is normal and shouldgo away in warm weather.

Page 15: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

© 2002 American Honda Motor Co., Inc - All Rights Reserved. BII 24451 (0209) 15 of 16

Bulb Replacement

1. Remove the two self-tapping screws that securethe fog light trim, and pull the fog light toward you.Unplug the connector, and remove the fog light.

2. Remove the bulb from the socket by turning itcounterclockwise and pulling it toward you.

Fog Light Aiming Adjustment

1. Adjust the fog lights:

• Adjust the aiming according to local laws andregulations.

• To adjust, turn the aiming adjustment screw inor out until the correct aiming is obtained.

3. Install the new bulb into the fog light.

• Use only a genuine Honda halogen light bulbof specified wattage.Rating: 12V 55W H11 Halogen Light Bulb

• Do not touch the bulb. Oily or greasysubstances on the bulb could shorten itsservice life due to the heat produced when thebulb is turned on. If the bulb is accidentallytouched, wipe it clean with a clean, soft cloththat has been dampened with denaturedalcohol or a mild detergent solution.

4. Reinstall the fog light in the reverse order ofremoval.

• Check that the wire harnesses are notpinched.

• Make sure you tighten the self-tapping screwssecurely.

FOG LIGHTBULB

BULB

FOG LIGHT

CONNECTOR

FOG LIGHT

SELF-TAPPINGSCREW

AIMINGADJUSTMENTSCREW

To raise.

To lower.

PHILLIPSSCREWDRIVER

Page 16: BII 24451 Fog Lights - Club RSX LIGHTS P/N 08V31-S6M-210 PARTS LIST Right fog light Left fog light trim Right fog light trim Left bracket Right bracket Switch harness Fog light harness

16 of 16 BII 24451 (0209) © 2002 American Honda Motor Co., Inc - All Rights Reserved.

CIRCUIT DIAGRAM

LIGHT SWITCH

OFFLow Hi

OFF

ON ON

FOG

LIG

HT

SW

ITC

H

B

Y

LG

R

W

BR

O

SBLG

P

GR

BLACK

YELLOW

BLUEGREEN

RED

WHITE

BROWN

ORANGE

SKY BLUELIGHT GREEN

PINK

GRAY

SMALLRELAY

COMBINATIONLIGHT SWITCH

LIGHTINGSWITCH

PASSING

DIMMER

R/W

R/LB B

L/R

W/G

BATTERY 100A

15A

20A

R/Y RIGHT LEFT

HEADLIGHTHILOW HILOW

20A

LIGHTINGRELAY 30A

W/R

20AR/Y

R/BR/L

L/Y

FOGLIGHTRELAY

FOGLIGHTS

B

FOGLIGHTSWITCH

R