birdhouse ornament in the round - woodcraft
TRANSCRIPT
Opening Photo: Michele Coleman; Project Photos: Jim Osborn Dec/Jan 2010 woodcraftmagazine.com 47
Two simple turnings (the body or house and the top or roof) combine to form a delightful tree trimmer. Try a variety of contrasting woods for different looks, and use a simple brass screw eye to hang the ornament with a hook. This is an ideal assignment for a beginning turner wanting to make a memorable gift for friends and loved ones.Note: See the Convenience-Plus Buying Guide for the items used in this story.
Begin with the body1 Mount a four-jawed chuck with standard 2" dovetail jaws to your lathe and securely tighten the jaws on a 1¾ × 1¾ × 4" blank (we used maple). Set your lathe speed to 2,000 rpm and use a 1" roughing gouge
to establish a 1¾"- diameter cylinder, as shown in Photo A.(Note: Use the same speed for all the turning stages unless specified.)2 Next, true up the end grain with a 3/8" spindle gouge, keeping the tip just below centerline.3 Decrease the speed to 1,000 rpm. Referring to the left-hand dimensions in Figure 1, use a rule and pencil to transfer the depth marks onto the cylinder as shown in Photo B, starting from the trued end.4 Stop the lathe. Using a drill and 3/8" brad-point bit, bore a ¾"-deep entrance hole where shown in Figure 1 and as
shown in Photo C. Switch to a 1/8" bit and drill the perch hole.5 Restart the lathe and increase the speed to 2,000 rpm. Using a 1/8" parting tool, cut a groove at the neck line, leaving a 7/8" diameter as shown in Photo D. Periodically check the diameter with a caliper.6 Switch to a 3/8" spindle gouge and shape the upper part of the body down to the neck line as shown in Photo D Inset.
Birdhouse Ornament in the RoundMake something “tweet” for the holidays.
Designer/Turner/Writer: Edward Thomson
A B C
Overall dimensions: 13/16"w × 4⅞"h
48 woodcraftmagazine.com Dec/Jan 2010
7 Then, with the tool rest centered on the workpiece, taper the body end with a 1" skew as shown in Photo E. Keep the bevel against the body, pushing it toward the end while using the heel of the skew. Use the Body Template to check the shape.8 Stop the lathe and angle the tool rest across the end grain. With a 1" skew flat on the tool rest, use the point of the skew to cut into the center of the body in small increments to a depth of ½". (You can see where the center is as the workpiece spins.) Switch
to a ¼" scraper and hollow the inside of the body down past the entrance hole (but not the perch hole). Leave the rim wall thickness at 1/8" (Photo F).9 Stop the lathe and reposition the tool rest parallel with the axis of the body. Now using a 3/8" spindle gouge, shape the stem down to 7/16" at the ball, as shown in Photo G. Shape the ball with a 1/8" parting tool as shown in the Photo G Inset.10 Decrease the speed to 1,000 rpm and lightly sand the body with 180-, 220-, and 320-grit
sandpaper (Photo H). Increase the speed to 2,000 rpm and part off the body with a 1/8" parting tool as shown in the Inset. Hand-sand the nub at the end of the ball.
Turn and add the top1 Chuck-mount a 17/8 × 17/8 × 3"-long blank for the birdhouse top. (Use a contrasting wood.) Turn the block to a 17/8" cylinder with a 1" roughing gouge and true the end with a 3/8" spindle gouge.2 Take the rule and measure the outside diameter of the body as shown in Photo I.
D
G
J
E
H
K L
F
I
3 Transfer the body measurement onto the trued end of the cylinder as shown in Photo J. This establishes the recess diameter.4 Using the point of a 1" skew, cut in 1/8" at the mark, and then hollow the recess with a ½" round-nose scraper to a depth of 1/8".5 Turn off the lathe and test the fit of the body in the top as shown in Photo K. Enlarge the opening if needed.6 Move the tool rest parallel to the axis and transfer the dimensions from the Top Template to the cylinder with a rule and pencil as before. Using a 3/8" spindle gouge, shape the top, leaving 5/16" at the chuck end. Check the shape against the template.7 Sand the top using 180-, 220-, and 320-grit sandpaper and then part off the top at a slight upward angle with the 1/8" parting tool to create a point. Hand-sand the top smooth.8 Cut a 1/8 × 1/8" strip of walnut 6" long, using a straightedge and utility knife. Hand-sand the piece to round over the corners. From it, crosscut a piece measuring 1¼" long for the perch.9 Apply a small amount of glue around the recess in the top. Fit the body in the top and rotate slightly to spread the glue. Dab a spot of glue in the perch hole and insert the perch, allowing ½" to protrude.10 Make a point in the center of the top with an awl and then screw in a ½" brass screw eye with 1/8" hole as shown in Photo L. Hang the ornament with a fine string and spray-finish it with two to three coats of satin lacquer. Once dry, dress up the birdhouse with a small bird glued to the perch. n
Dec/Jan 2010 woodcraftmagazine.com 49
About Our Turner“Woodturning is my way of relaxing from my everyday job as a cabinet and furniture maker,” says West Virginian Edward Thomson. Several years ago, Ed began turning by making small turned gifts for family and friends using leftover scraps of wood. He now sells his turned items at craft shows and galleries.
ITEM WOODCRAFT # PRICE
1. Nova G3 Chuck 147016 $139.99
2.Woodturner’s Color Pack, Four 2 × 2 × 12" Squares in Walnut, Maple, Padauk, and Purpleheart (Enough for 6 Birdhouses)
840185 $19.99
Above items are available at Woodcraft stores, woodcraft.com or by calling(800) 225-1153. Prices subject to change without notice.
3..Pete, the Little Cardinal (optional), available from Floraltrims.com: #201329, $10.80 plus $5.99 shipping, pack of 36 birds (½"). Call (800) 589-1199 or visit floraltrims.com.
Convenience - PLUS BUYING GUIDE
Figure 1: Birdhouse Section View
Full-Sized Templates
Note: Make a copy of the Top and Body Templates. Spray-adhere them to the cardboard and cut to shape. Hold them against your work to check progress.
FREE YEAR!
go to woodcraftmagazine.comand click SUBSCRIBE
Complete the form below and mail in an envelope addressed to:
-or-
WOODCRAFT MAGAZINEPO BOX 7020
PARKERSBURG WV 26102-9916
2 YEARS for $29.99!
Outside of the U.S and Canada add $30 for postage. Foreign orders must be prepaid. Payment in U.S. Funds only.
By providing my e-mail address, I am indicating I’d like to receive information about my subscription and other offers from Woodcraft Magazine via e-mail.
□ Payment Enclosed □ Bill Me
Name
Address
City
State Zip
Country
Send in now to get
2 Years for $29.99!Projects, Techniques and Products
n Dovetail a casen Divide a cabinet into
compartmentsn Create a cornice
n 4 more projectsn Famous furniture
And learn how to…
Plus…
Best-everLUMBER RACK
DECORATIVE FINISHES Done Right
Build Betterwith a CUT LIST
SPICE BOXBuild this classic
or go to woodcraftmagazine.com and click SUBSCRIBE