black and decker pivot plus pd600 battery … guides/black and...black and decker pivot plus pd600...

5
Black and Decker Pivot Plus PD600 Battery Replacement This guide details how to take apart the Black and Decker Pivot Plus PD600 to replace the battery. Written By: Jonathon Centofranchi Black and Decker Pivot Plus PD600 Battery Replacement © iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 5

Upload: others

Post on 13-Mar-2020

6 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Black and Decker Pivot Plus PD600 Battery … Guides/Black and...Black and Decker Pivot Plus PD600 Battery Replacement This guide details how to take apart the Black and Decker Pivot

Black and Decker Pivot Plus PD600 BatteryReplacement

This guide details how to take apart the Black and Decker Pivot Plus PD600 to replace the battery.

Written By: Jonathon Centofranchi

Black and Decker Pivot Plus PD600 Battery Replacement

© iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 5

Page 2: Black and Decker Pivot Plus PD600 Battery … Guides/Black and...Black and Decker Pivot Plus PD600 Battery Replacement This guide details how to take apart the Black and Decker Pivot

INTRODUCTION

If your drill stops working and the battery stops holding a charge chances are you need a newbattery. You can find a replacement parts including the battery under the replacement part links inthe device page. This guide will show you how to install this new battery.

TOOLS:Phillips #1 Screwdriver (1)

Black and Decker Pivot Plus PD600 Battery Replacement

© iFixit — CC BY-NC-SA www.iFixit.com Page 2 of 5

Page 3: Black and Decker Pivot Plus PD600 Battery … Guides/Black and...Black and Decker Pivot Plus PD600 Battery Replacement This guide details how to take apart the Black and Decker Pivot

Step 1 — Drill

Remove the nine 15mm Philips #1 screws

Remove the two 12.5mm Philips #1 screws

Remove the two 10mm Philips #1 screws

Step 2

Lift one side of the drill casing off ofthe drill. Note that the drill casingconsists of two pieces on either sideof the drill.

Black and Decker Pivot Plus PD600 Battery Replacement

© iFixit — CC BY-NC-SA www.iFixit.com Page 3 of 5

Page 4: Black and Decker Pivot Plus PD600 Battery … Guides/Black and...Black and Decker Pivot Plus PD600 Battery Replacement This guide details how to take apart the Black and Decker Pivot

Step 3 — Battery

Locate the battery and remove itfrom its slot at the end of the drillopposite the motor. It should be atthe butt of the drill by the handle.

Step 4

Unplug the battery by pulling outboth the red and black wires. Theyshould come out easily with a littlebit of force.

But be careful not to disconnect thewire from the metal it is attached to.In order to avoid this, pull the wireout by holding on to the metal partinstead of just the wire.

Black and Decker Pivot Plus PD600 Battery Replacement

© iFixit — CC BY-NC-SA www.iFixit.com Page 4 of 5

Page 5: Black and Decker Pivot Plus PD600 Battery … Guides/Black and...Black and Decker Pivot Plus PD600 Battery Replacement This guide details how to take apart the Black and Decker Pivot

To reassemble your device, follow these instructions in reverse order.

This document was last generated on 2017-06-18 12:41:10 AM.

Step 5

Now take the replacement batteryand slide the metal parts of the wireinto the metal part of the battery.

Make sure that the red wireconnects to the curved end of thebattery, and that the black wireconnects to the straight end of thebattery.

Black and Decker Pivot Plus PD600 Battery Replacement

© iFixit — CC BY-NC-SA www.iFixit.com Page 5 of 5