• Paper • Tin • Fabric

• Leather • Chipboard • Wood

• Plastic • Acrylic • Poly

Finally - no clicking, banging, pounding, twisting, grunting or cussing! This all-in-one tool punches and sets eyelets, snaps, and so much more. Easily punch through almost any material, even thick bookboard, then set eyelets, snaps or any embellishment in your project. It is perfect for all kinds of projects, even custom bindings. Let your imagination run wild with this amazing tool!

INSTRUCTIONS:

1. Grab your CROP-A-DILE™. Determine the desired hole size. Set hole depth using the depth gauge near the punch. Make sure that TOP and BASE black cubes are locked and secured before moving on. Insert material in the appropriate slot, and punch by compressing the handles (fig. 1).

2. Select your snap, eyelet or metal embellishment. Determine the correct TOP and BASE combination (see combination chart below) for the type of metal embellishment selected and rotate them to the correct position. Make sure that TOP and BASE black cubes are locked in position and secured before moving on.

3. Place eyelet, snap, or other embellishment in the hole and then line up the BASE of the CROP-A-DILE™ in the tube of the snap or eyelet and compress (fig. 2).

Note: The back side of your snap or eyelet may be bent, curled, or look smashed which is totally normal. Non-uniform crimping may occur depending upon the type of metal embellishment used and how well you line up the tool when crimping.Warning: Failure to follow instructions for usage may result in damage of this tool and will void manufac-turer warranty.

MODO DE USO:• Agarre su CROP-A-DILE™. Determine el tamaño del agujero que necesita. Ajuste la profundidad del agujero usando el medidor de profundidad cerca del agujero. Meta el papel, cartón, cuero, metal o cualquier material - grueso o delgado - y abra el agujero.• Seleccione su broche, ojete o embellecimiento metálico que quiera usar. Determine la combinación correcta del tope y la base (ver abajo) por el tipo de metal o embellecimiento que ha seleccionado y rote para la posición correcta.• Coloque su ojete, broche u otro embellecimiento en el agujero que ha hecho, y alinee la base del CROP-A-DILE™ en el agujero del broche u ojete y oprima.Nota: La parte de atrás de su broche u ojete puede ser doblada ondulada, o mirarse aplastada - esto es totalmente normal. Dobladuras no uniforme pueden ocurrir dependiendo en el tipo de embellecimiento metálico que esté usando y que tan bien está alineado con la herramienta cuando se dobla.

MODE D’EMPLOI:• Prenez votre CROP-A-DILE™ et determinez les dimensions de trou que vous desirez. Placez le profondeur de trou en utilisant la jauge de profondeur pres du punch. Inserez le papier, metal, carton, cuir ou n’import quel matériel epais ou mince et presser.• Choisissez le fermoir, œillet ou embellisement metal que vous desirez utiliser. Determinez le combinasion de dessus et base correct (voir au dessous) pour l’embellisement métal que vous avez choisi et tourner au position correct.• Mettez le fermoir, œillet ou embellishment dans le trou que vous avez fait. Puis aligner le base du CROP-A-DILE ™ dans le trou du fermoir ou œillet et compresser.NOTE: Le revers de votre femoir ou œillet peut être tordu, bouclé, ou peut sembler écrasé. C’est totallement normale. Ce peut arriver dependent de type d’embellisement et comment vous alignez l’instrument.

IDEAL FOR PUNCHING:

Ojetes Broches Grandes y Extra Grandes: Para todos los ojetes y broches de 3/16 estándar, tamaños grandes y misceláneos. Ojete y Broche Mediano: Para todos los tamaños no estándares tamaños grandes y para broches y ojetes misceláneos. Ojete y Broche Pequeño en Llamas: Para todos los broches y ojetes de un 1/8 de pulgada y tamaños mas grandes. Forma de Cono en Llamas: Para todos los broches y ojetes donde el tubo del ojete no está completa-mente hueco, y para otras formas misceláneas de broches y ojetes metálicos.

Ajustador de Ojete de 3/16 de pulgada: Para todos los ojetes de 3/16 de pulgada y tamaños mas grandes. Ajustador de Broche Redondo de 1/8 de pulgada: Forma de plato para todos los broches redondos de 1/8 de pulgada. Ajustador de Ojete de 1/8 de pulgada: Para todos los ojetes de un 1/8 de pulgada y tamaños grandes. Ajustador Plano: Para todos los broches y embellecimientos metálicos de forma cuadrada, misceláneos o tamaños grandes.

DESSUSŒillet 3/16 pouce: Pour tous les œillets qui sont 3/16 pouce et enormé. Fermoir 1/8 pouce: Pour tous les fermoirs rond et 1/8 pouce. 1Œillet 1/8 pouce: Pour tous les œillets standard qui sont 1/8 pouce. Plat: Pour tous les embellisements métal carré et enormé.

BASEGrand/Plus Grand œillets et fermoirs: Pour tous les œillets et fermoirs 3/16 pouce et enormé. Fermoirs et œillets de taille moyenne: Pour des autres dimensions. Petit œillets et fermoirs: Pour tous les œillets et fermoirs standard et 1/8 pouce. Profile cone: Pour les fermoirs et œillets de divers profiles et qui n’ont pas un tube vide.

B

A

D

C

1

2

4

3

Step One: Pick up a small tin bucket from your local craft and hobby store. * Make sure the tin is THIN! Too thick of tin will break your Crop-A-Dile™

Step Two: Using the 3/16” hole punch, set your depth gauge on your Crop-A-Dile™ to 1/2”. Punch ten holes that are evenly spaced apart.

Step Three: Rotate and lock the HEAD of your Crop-A-Dile™ to “A” and the BASE to “1”. Set your 3/16” eyelets in alternating colors.

Step Four: Once eyelets are set, loop ribbon through the middle eyelet on the bucket and the eyelet on your tag and tie a bow or knot.

Step Five: Fill the bottom third of your bucket with potting soil. Gently remove your flower or plant from plastic container and place in bucket. Hold the plant straight and fill the remaining space with soil.

Here’s an adorable easy project that is sure to brighten up anyone’s day! With the help of the Crop-A-Dile™ and in five quick steps, you’ll take a regular tin bucket and make it something beautiful. This project is a perfect way to show customers how fun and easy the Crop-A-Dile™ is to use!

For this project you’ll need:• Crop-A-Dile™• One tin bucket• Ten eyelets (two different colors)• 6”-10”of ribbon• 1 tag• Your favorite flower or plant.

* Thick or hard metals can damage and/or possibly break your tool. Pick thin and soft metal in your projects when using the Crop-A-Dile™

1/8

3/16

1/8” hole punch

top

depth gauge

base

depth gauge 3/16” hole punch

1/8

3/16

fig. 1

1/8

3/16

fig. 2

*This shows the correct way to set an Extra Large Eyelet.See Top and Base Combination Charts for correct

combinations for other types of embelishments.

BASE

TOP

B2

CORRECT*

BASE

TOP

B2

INCORRECT

3/16 INCH EYELET SETTER For all 3/16 inch standard and oversized eyelets 1/8 INCH ROUND SNAP SETTER Dish shaped for all 1/8 inch round standard snaps 1/8 INCH EYELET SETTER For all 1/8 inch standard and oversized eyelets FLAT SETTER For all oversized, miscellaneous, and square shaped metal embellishments and snaps

LARGE/EXTRA LARGE EYELET AND SNAP FLARE For all 3/16 inch standard, oversized, and miscellaneous eyelets and snaps MEDIUM EYELET AND SNAP FLARE For other non-standard, oversized, and miscellaneous eyelets and snaps SMALL EYELET AND SNAP FLARE For all 1/8 inch standard, oversized, and miscellaneous eyelets and snaps CONE SHAPED FLARE For snaps and eyelets where the eyelet tube is not completely hollow and for other miscellaneous cast metal eyelets and snap shapes

1

2

3

4

B

C

A

D

TAPA

BASE

B

A

D

C

1

2

4

3

1

2

3

4

B

C

A

D

TOP

BASE

B

A

D

C

1

2

4

3

1

2

3

4

B

C

A

D

BLUE LINES IS WHERE IT FOLDS