bmtf presentation
TRANSCRIPT
![Page 1: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/1.jpg)
Industrial & Production Engineering (IPE) DHAKA UNIVERSITY OF ENGINEERING &
TECHNOLOGY(DUET), GAZIPUR-1700
Presentation On
Industrial Training
Presented by-Sayem Mahmud (117012)Abdur Rahman (117015)Shariful Islam (117019)Bazlur Rashid (117030)
![Page 2: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/2.jpg)
Training atBangladesh Machine Tools
Factory (BMTF) Ltd.
(BMTF) Ltd. is one of the largest company enterprises in Bangladesh Management under the Bangladesh Army; Located at Gazipur about 40km away from Dhaka.
BMTF is well equipped with variety of high production machineries and equipment’s.
![Page 3: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/3.jpg)
1. PATTERN
The foundries are served with ‘In House’ pattern making facilities
There are five(5) tools used for pattern making, which are:-
Measuring instrument Cutting tools Helping tools
Marking tools Planning tools
![Page 4: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/4.jpg)
2. CASTING
The mechanized foundries of BMTF are the largest in Bangladesh
output of about 5000 tons per year.International quality standardsLine Hardware, Two case centrifugal Pump, Hand
Tube Well
![Page 5: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/5.jpg)
3. FORGING
Equipped with all kinds of forging machines like hammer, presses and special forging machines.
To make best quality product used die and subsequent heat treatment facilities.
![Page 6: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/6.jpg)
3. FORGING(CONTINUED)
A forming press, commonly shortened to press, is a machine tool that changes the shape of a workpiece by the application of pressure. Presses can be classified according to their mechanism: hydraulic, mechanical, pneumatic; and their function: forging presses, stamping presses, press brakes, punch press, etc.
![Page 7: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/7.jpg)
3. FORGING(CONTINUED)
Drop hammerA machine consisting of an anvil or base aligned with a hammer that is raised and then dropped on normalized metal, used to forge or stamp the metal resting on the anvil.
![Page 8: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/8.jpg)
4. PROJECTS
Rice crasher machine Guti Urea Maker Power Tiller
Sugarcane Power Crasher Harvester Pump
![Page 9: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/9.jpg)
5. ASSEMBLY
THERE ARE SIX(6) STAGES IN THE ASSEMBLY LINE
FRAME AXLE LINE PIPE LINE
ENGINE & TRANSMISSION LINE
TRANSFER INSTALLATION LINE
CABIN INSTALLATION
![Page 10: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/10.jpg)
FRAME
AXLE LINE AXLE LEAF SPRING DISH WHEEL SUSPENSION
![Page 11: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/11.jpg)
PIPE LINE PIPING HARNESS BRACKET AIR TANK
ENGINE & TRANSMISSION LINE ENGINE SUB ASSY RADIATOR PITMAN
![Page 12: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/12.jpg)
TRANSFER INSTALLATION LINE TRANSFER LINE PROPELLER SHAFT FUEL TANK
CABIN INSTALLATION DASH BOARD STEERING COLUMN SEAT
![Page 13: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/13.jpg)
STEERING GEOMETRY
Camber Angle: Camber is the angle of the wheel relative to the road
Caster Angle: Caster is the angle of the wheel relative to the axis line.
Toe in:Toe in occurs when two wheel are “A” shape.
Toe out: Toe out occurs when two wheel are “V” shape.
![Page 14: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/14.jpg)
Heat Treatment
Heat treatment is the process of heating and cooling metals to achieve desired physical and mechanical properties.
The processes of heat treatment1. Carburizing2. Quenching3. Tempering 4. Induction hardening
![Page 15: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/15.jpg)
CARBURIZING
Carburizing is a heat treatment process in which iron or steel absorbs carbon liberated when the metal is heated in the presence of a carbon bearing material, such as charcoal or carbon monoxide.
![Page 16: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/16.jpg)
1. It has 30 pieces coil around the furnace.
2. The capacity of coil is 30 ohm.3. It can heated the job 950 °C.4. The temperature maintained until at
least 6 hours.5. Then the switch was off and cooled
the w/p in the furnace at 250 °C temperature.
CARBURIZING(continued)
![Page 17: BMTF Presentation](https://reader035.vdocuments.net/reader035/viewer/2022070518/58e8aa331a28abda4f8b51c1/html5/thumbnails/17.jpg)
THANK YOU FOR PATIENT HEARING