BN-DS-A000 Design Standards OverviewThe design standards provide ready to use examples and design dimensions for equipment, piping and other disciplines. These standards are usually not part of the auditable section of the QAsystem. The focus of the guides is primarily related to project execution because the procedures are written from the perspective of an Engineering Contractor.

The below listing gives an indication of the available procedures. Use Library Menu navigation bar at the left to view the public procedures on this website or use this link to go directly to the QA systemdocuments >

Number TitleBN-DS-A0 Index of Vessels and Heat Exchangers Standard DrawingsBN-DS-A1 Base Ring and Lug Details for Vertical VesselsBN-DS-A10 Engineering Nameplate With Bracket for VesselsBN-DS-A11 Flanges for Nonpressure Pipe ConnectionsBN-DS-A12 Typical Detail for Earthing ConnectionsBN-DS-A15 Hatchway Covers for VesselsBN-DS-A18 Typical Demister Supports for VesselsBN-DS-A19 Typical Demister Supports for Reduced Size DemistersBN-DS-A2 Typical Construction Details for VesselsBN-DS-A20 Typical Standouts for Nozzles and ManwaysBN-DS-A21 Tank NameplateBN-DS-A22 Internal Pipe Support DetailsBN-DS-A3-1 Construction Tolerances for Pressure VesselsBN-DS-A3-2 Construction Tolerances for Pressure VesselsBN-DS-A4-1 Davit for Manway CoversBN-DS-A4-2 Davit for Manway CoversBN-DS-A5 Insulation Support Details for Hot Service VesselsBN-DS-A6 Attachments for Fireproofing on Vessel SkirtsBN-DS-A7-1 Standard Connections and Welding for Clad Steel VesselsBN-DS-A7-2 Standard Connections and Welding for Clad Steel VesselsBN-DS-A8 Typical Construction Details for Nonpressure VesselsBN-DS-A9 Typical Details of Davits for TowersBN-DS-B1 Fencing for Transformer YardsBN-DS-C1 Piping Design StandardsBN-DS-C10 Slip-On Threaded and Socket Type Flanges - ANSI 150, 300,400 and 600 LbBN-DS-C11 Lap Joint Stub Ends and CapsBN-DS-C12 WeldoletsBN-DS-C14 Machine and Stud Bolt Dimensions for Flanges - 150, 300, 400, 600, 900, 1500, and 2500 Lb (Dimensions In Inches)BN-DS-C15 Machine and Stud Bolt Dimensions for Flanges - 150, 300, 400, 600, 900, 1500, and 2500 Lb (Dimensions In Mm)BN-DS-C16 Dimensions and Bolting ANSI 300lb, Steel Orifice FlangesBN-DS-C18 90 Deg. Miter Bends - R=d and 1 1/2d Nom (3 Sections)BN-DS-C2 Dimensions and Particulars of Line Pipe(Metric Units)BN-DS-C22 Y-Type Suction StrainersBN-DS-C25 Recommended Maximum Horizontal Spans In MetersBN-DS-C26 Maximum Pipe Spans Based Upon Deflection and StressBN-DS-C29 Swaged NipplesBN-DS-C3 Dimensions of ValvesBN-DS-C32 'l' Bend NomogramBN-DS-C33 Thermal Expansion DataBN-DS-C38 Inches and Fractions of an Inch Expressed as Decimals of a FootBN-DS-C39 Wire and Sheet Metal GaugesBN-DS-C4 Dimensions of Line Pipe, Reducers, Elbows, Caps and Required spacing Between LinesBN-DS-C40 Metric Conversion Table Inches and Fractions of an Inch to MillimetersBN-DS-C41 Metric Conversion of Pressures, Weights, Volumes and TemperaturesBN-DS-C42 Pipe Spacing Standard. Metric UnitsBN-DS-C43 Typical Pump PipingBN-DS-C44 Condensate Pots for Steam MainsBN-DS-C45 Typical Service Station Hookup at Grade and at PlatformBN-DS-C46 Typical Steam Snuffing Manifold for Non-Freezing ClimatesBN-DS-C47 Plot Arrangement and Typical Section thru Pipe-WayBN-DS-C48 Typical Exchanger Piping and Data. Horizontal Exch.BN-DS-C49 Typical Airfin Piping and DataBN-DS-C5 Dimensions 30 Deg. and 60 Deg. BendsBN-DS-C50 Dimensions for Screwed & Socket Weld Fittings Thread Engagements & Socket DepthsBN-DS-C51 Projection for Welded on Fittings - Full Sizes, Reducing Sizes & 45 Deg. Branch Conn'sBN-DS-C52 Drawing FormatBN-DS-C53 Fldg. Contr. Vlv. Piping Manifold 150, 300 and 600 Lb Gate Vlvs. C.S.BN-DS-C54 Flgd. Contr. Vlv. Piping Manifold 150, 300 - 600 Lb Gate Vlvs. Mss Stub Ends.BN-DS-C55 Two Weld 90 Deg. Miter ElbowBN-DS-C56 Two Weld 45 Deg. L.R. Miter ElbowBN-DS-C57 One Weld 45 Deg. Miter ElbowBN-DS-C58 Three Weld 90 Deg. L.R. Miter ElbowBN-DS-C59 Three Weld 90 Deg. S.R. Miter ElbowBN-DS-C6 Ansi Standard Welding TeesBN-DS-C60 Five Weld 90 Deg. Miter ElbowBN-DS-C61 Standard Dim's for Temporary Strainers (Conical Type)BN-DS-C62 Special Fabricated Large Dia. Conc. Ecc. ReducersBN-DS-C63 Clearances Req'd for PersonnelBN-DS-C64 Ring Type Joint Dim's for Valves & FlangesBN-DS-C65 Fuel Piping Vertical Cylinder HeatersBN-DS-C66 Spectacle Flange Single Blind-Ring Spacers/ring Joint Male/ring Joint Female/dimensions & WeightsBN-DS-C67 Jack Screws Size Selection and Installation Detail for Ff, Rf and RjBN-DS-C68 Dim's for W.N. Flg's 26 Inch - 60 Inch API Std. 605 150 - 300 and 900 Lb.BN-DS-C69 Minimum Spacing for Refineries and Petrochemical PlantsBN-DS-C7 150 Lb ANSI Fabricated Flanged FittingsBN-DS-C70 Valve Locking ArrangementBN-DS-C8 300 Lb ANSI Fabricated Flanged FittingsBN-DS-C9 Welding Neck Flanges - ANSI 150, 300, 400, 600, 900, 1500, and 2500 LbBN-DS-E1 Electrical Design Standard IntroductionBN-DS-E2 Electrical Design Standards SymbolsBN-DS-E3 Electrical Design Direct Burial of CablesBN-DS-E4 Electrical Design Cable IdentificationBN-DS-E6 Electrical Design Conduits for CablesBN-DS-E7 Electrical Design Above Grade InstallationBN-DS-E8 Electrical Design Lighting and Receptacle InstallationBN-DS-E9 Electrical Design Standard, EarthingBN-DS-J1 Sealed Catch BasinBN-DS-J10 Tank PadsBN-DS-J11 Tank PadsBN-DS-J12 Tank Pads

BN-DS-A000 Design Standards Overview http://www.red-bag.com/jcms/design-standards/74-bn-ds-a000-design-stan...

1 of 2 8/15/2013 4:27 PM

BN-DS-J13 General Notes Applicable to Civil Construction DrawingsBN-DS-J14 Precast Concrete StairsBN-DS-J18 Foundation for Horizontal VesselBN-DS-J19 Foundation for Horizontal VesselBN-DS-J2 Foundation for TowerBN-DS-J20 R.C. Foundation for Tanks (Ring Shaped)BN-DS-J21 R.C. Foundation for Tanks (12 Sided)BN-DS-J22 R.C. Foundation for Tanks (24 Sided)BN-DS-J23 R.C. Rings Around Tank FoundationsBN-DS-J24 Prefabricated R.C. ManholesBN-DS-J25 Brickwork ManholesBN-DS-J26 Prefabricated R.C. Manholes (Composed of Elements)BN-DS-J27 Steel Slide for Heat ExchangersBN-DS-J28 Steel Slide Plates for Horizontal VesselsBN-DS-J29 Wooden Insulation Blocks for Cold Heat ExchangersBN-DS-J3 Foundation for Heat ExchangerBN-DS-J30 Wooden Insulation Blocks for Cold Horizontal VesselsBN-DS-J31 Bolts for Wooden Blocks Under Cold Heat Exchangers and Horizontal VesselsBN-DS-J32 Concrete Stair-And Ladder Supports at GradeBN-DS-J33 Preload Settlement StakeBN-DS-J34 Bench MarksBN-DS-J4 Foundation for Heat ExchangerBN-DS-J5 Foundation for Pumps Soil BearingBN-DS-J6 Foundation for Vertical DrumBN-DS-J7 Foundation for Vertical DrumBN-DS-J8 Sleepers Type 1 and 2BN-DS-J9 Sleepers Type 3 & 4BN-DS-M1 Saddles for Horizontal VesselsBN-DS-M2 Sliding Plate for Saddle of Horizontal Apparatus (Shell Dia 1000 Up/inclusive 4000 Od)BN-DS-M3 Sliding Plate for Saddles of Horizontal Apparatus (Nominal Shell Dia 150 Up/inclusive 950)BN-DS-T1 Heat Exchanger Bull PlugsBN-DS-T11 Saddles for Heat Exchangers and VesselsBN-DS-T13 Typical Construction Details for Test Rings of Floating Head Type ExchangersBN-DS-T15 Test Flange for Testing Tubes at Stationary Tube SheetBN-DS-T16 Typical Details for Lined Floating HeadBN-DS-T17 Typical Detail and Tolerances of Backing Ring With Connecting PiecesBN-DS-T19 Typical Detail Tube Hole Grooving and RollingBN-DS-T2 Jack Screws for Girth Flanges of Heat ExchangersBN-DS-T20 Typical Detail Tube Hole Grooving and Welding TubesBN-DS-T21 Typical Detail Tube Hole Rolling and Welding Tubes (Without Grooving)BN-DS-T22 Typical Detail Tube Hole Grooving, Rolling and Welding TubesBN-DS-T23 Typical Detail Tube Hole Rolling and Welding Tubes (Without Grooving)BN-DS-T24 Typical Detail Tube Hole Grooving and Rolling of Bimetalic Tube SheetsBN-DS-T25 Typical Detail Tube Hole Grooving and Rolling of Bimetalic Tubes In Bimetalic Tube SheetBN-DS-T26 Typical Detail Tube Hole Grooving, Welding & Rolling of Bimetallic Tube SheetsBN-DS-T27 Typical Detail Tube Hole Grooving and Rolling of Double Tube SheetsBN-DS-T28 Typical Detail Tube Hole Grooving, Welding and Rolling of Double Tube SheetsBN-DS-T3 Typical Detail Bundle Tie Rod With SpacersBN-DS-T4 Typical Detail Welded Bundle SpacerBN-DS-T5 Typical Detail Welded Bundle Tie RodBN-DS-T7 Sealing Strips for Longitudinal BafflesBN-DS-T8 Lifting Lugs for Heat Exchangers

BN-DS-A000 Design Standards Overview http://www.red-bag.com/jcms/design-standards/74-bn-ds-a000-design-stan...

2 of 2 8/15/2013 4:27 PM