bronze check valves - hattersley - future valve … 3 hattersley offers four basic types of bronze...
TRANSCRIPT
04.06
Bronze Check Valves
SECTION4a
Tel: +44 (0)1695 712800 Fax: +44 (0)1695 712820Email: [email protected]
Hattersley-Section 4a 25/4/06 9:34 am Page 1
2 04.06
Contents PageFigure Number Index 2Bronze Check Valves Introduction 3Bronze Check Valves Data Sheets 4 - 13
Fig No Page
42 447 548 649 7149 8249 8249C 80123NR 90123NRSL 91013 101213 113047 125870 13
In this catalogue we have endeavoured to make the information as accurate aspossible, but we cannot accept any responsibility should it be found that in anyrespect the information is inaccurate or incomplete or becomes so as result offurther developments.
Bronze Check Valves
Contents
Hattersley-Section 4a 25/4/06 9:34 am Page 2
304.06
Hattersley offers four basic types ofbronze check valves namely:
■ Horizontal lift check■ Vertical lift check■ Swing check■ Double check
Swing check valves having 6 diametersof straight lengths of pipe upstreamand 3 diameters downstream aresuitable for velocities up to 3metres/second. If the valve is situatedsuch that turbulent flow enters thevalve, the velocity should not exceed2 metres/second.
Horizontal lift check valves areprimarily used for air, gas and steamservices whilst swing check valves are most suitable for water and other liquids.
For air, gas and low pressureapplications, especially where bubbletight closure is required, a valve withrubber faced disk is necessary.
Compressed air service requires ahorizontal lift check valve with anitrile rubber facing on the disk andfitted with a recoil spring.The valveshould always be installed as far awayfrom the compressor as possible.
When selecting valves, reference tocodes of practice and othermandatory specifications should bemade which may preclude certaintypes for specific applications.
Double check valves are designed toprevent contamination of watercaused by back siphonage, back flowand cross connection in supplies suchas those to hose taps, cisterns, standpipes, showers and basins.
Valves, where designated, are WRAS Approved Products and listed in the Water Fittings andMaterials Directory.
Fig No PN Series Class End Size Pattern Disk SeatRating Rating Connections Range Material Material
3047 25 Restricted - Threaded 1/2 - 2in Swing Rubber Integral47 25 B 150 Threaded 1/4 - 3in Swing Bronze Integral42 32 B 200 Threaded 1/2 - 2in Horizontal Lift Bronze Integral49 32 B 200 Threaded 1/2 - 2in Vertical Lift Bronze Integral48 32 A 200 Threaded 1/2 - 2in Oblique Swing Bronze Integral1013 32 B 200 Threaded 1/2 - 2in Horizontal Lift Filled PTFE Integral1213 32 Restricted - Threaded 1/2 - 2in Horizontal Lift Rubber Integral0123NR - A 250 Threaded 1/2 - 2in Horizontal Lift Stainless Steel Stainless Steel5870 16 bar Wafer 50 - 350mm Swing Bronze EPDM149 16 - - Compression 15 & 22mm Single Check Brass PTFE249 16 - - Compression 15, 22 & 28mm Double Check Brass PTFE249C 16 - - Compression 15mm Double Check Brass PTFE
Introduction
Bronze Check Valves
Hattersley-Section 4a 25/4/06 9:34 am Page 3
4 04.06
Pressure/Temperature RatingBS5154 PN32 Series B14 bar at 198ºC32 bar from -10 to 100ºC
Test Pressures (Hydraulic)Shell: 48 barSeat: 35.2 bar
SpecificationHorizontal lift patternThreaded coverMetal to metal seatEnds threaded internal to BS EN 10266 (ISO 7)Available with NPT thread (42AT)
Satura
ted
Stea
m
0 40 80 120 160 200 240 Temperature ˚C
28
24
20
16
12
4
0
Pre
ssur
e ba
r
8
32
36
Material Specification
Specification
Component Material BS EN ASTM
Cap Cast Bronze 1982 CC491K B62
Disk Cast Bronze 1982 CC491K B62
Body Cast Bronze 1982 CC491K B62
Dimensions
Nominal Size in 1/2 3/4 1 11/4 11/2 2
A mm 60 74 86 99 109 130
B mm 39 43 51 58 64 70
Weight kg 0.3 0.6 0.7 1.4 1.8 3.1
Fig. 42
Bronze Check Valves - Horizontal LiftPN32 Series B 1/2” - 2”
B
A
Hattersley-Section 4a 25/4/06 9:34 am Page 4
504.06
Pressure/Temperature RatingBS5154 PN25 Series B10.5 bar at 186ºC25 bar from -10 to 100ºC
Test Pressures (Hydraulic)Shell: 37.5 barSeat: 27.5 bar
SpecificationSizes 1/4 to 3in Kitemarked to BS5154Horizontal swing patternThreaded coverMetal to metal seatEnds threaded internal BS EN 10266 (ISO 7)Suitable for mounting in horizontal andvertical pipe (with vertical flow upwards).
Fig. 47
Bronze Check Valves - Swing PatternPN25 - Series B
0 30 60 90 120 150 180Temperature ˚C
28
24
20
16
12
4
0
Pre
ssur
e ba
r
8
A
B
Material Specification
Specification
Component Material BS EN ASTM
Body Bronze 1982 CC491K
Cap Bronze 1982 CC491K
Disc (1/4 - 1in) Brass 12164 CW614N
(11/4 - 3in) Bronze 1982 CC491K
Hinge Bronze 1982 CC491K
Hinge Pin (1/4 - 1in) Stainless Steel 970 GR316S11
(21/2 - 3in) Brass 12164 CW614N
Hinge Nut Brass 12164 CW614N
Identity Plate Aluminium
Drive Screw Steel - Electro Brassed
Hinge Pin Plug (21/2 - 3in) Brass 12164 CW614N
Dimensions
Nominal Size in 1/4 3/8 1/2 3/4 1 11/4 11/2 2 21/2 3
A mm 48 48 58 66 80 89 95 108 155 190
B mm 33 33 38 42 49 56 65 76 98 99
Weight kg 0.20 0.19 0.32 0.43 0.61 1.01 1.34 2.12 4.08 5.76
Hattersley-Section 4a 25/4/06 9:34 am Page 5
6 04.06
Pressure/Temperature RatingBS5154 PN32 Series A14 bar at 260ºC32 bar from -10 to 120ºC
Test Pressures (Hydraulic)Shell: 48 barSeat: 35.2 bar
SpecificationOblique swing patternThreaded coverMetal to metal seatEnds threaded internal BS EN 10266(ISO 7)Suitable for mounting in horizontal and vertical pipe (with vertical flow upwards). Material Specification
Specification
Component Material BS EN
Cap Bronze 1982 CC491K
Hinge Pin Bronze 1982 CC491K
Hinge Bronze 1982 CC491K
Hinge Pin Plug Brass 12165 CW617N
Disk Bronze 1982 CC491K
Disk Nut Brass 12165 CW617N
Body Bronze 1982 CC491K
Dimensions
Nominal Size in 1/2 3/4 1 11/4 11/2 2
A mm 60 70 86.4 96 116 136
B mm 45 50 58 68 75 94
Weight kg 0.6 1.0 1.4 2.2 3.0 4.6
B
A
Fig. 48
Bronze Check Valves - Oblique Swing PatternPN32 Series A 1/2” - 2”
Hattersley-Section 4a 25/4/06 9:34 am Page 6
704.06
Pressure/Temperature RatingBS5154 PN32 Series B14 bar at 198ºC32 bar from -10 to 100ºC
Test Pressures (Hydraulic)Shell: 48 barSeat: 35.2 bar
SpecificationVertical lift patternMetal to metal seatEnds threaded internal BS EN 10266(ISO 7)Suitable for vertical flow upwards only.
Fig. 49
Bronze Check Valves - Vertical Lift PatternPN32 Series B 1/2” - 2”
Satura
ted
Stea
m
0 40 80 120 160 200 240 Temperature ˚C
28
24
20
16
12
4
0
Pre
ssur
e ba
r
8
32
36
Material Specification
Specification
Component Material BS EN
Body Bronze 1982 CC491K
Disc Bronze 1982 CC491K
Spring Stainless Steel S304
Dimensions
Nominal Size in 1/2 3/4 1 11/4 11/2 2
A mm 53 59 68 79 88 98
Weight kg 0.2 0.3 0.4 0.7 1.2 1.6
A
Hattersley-Section 4a 25/4/06 9:34 am Page 7
8 04.06
Specification
Fig No. 149Single Check - 15mm, 22mm Fig No. 249Double Check - 15mm, 22mm, 28mmFig No. 249CDouble Check chromium plated - 15mm
Manufactured to BS 6282WRAS approved PN16 85ºCApplication:WaterEnd Connection: CompressionBack Flow Prevention Device category:Single check - Class 2 as per WaterSupply Contamination Risks (waterfittings) Regulations 1999. Doublecheck - Class 3 as per Water SupplyContamination Risks (water fittings)Regulations 1999.
Fig. 149, 249 & 249C
Brass Check Valves - Single Check,Double Check, Double Check Chromium Plated
D
B B
A
C
E
Material Specification
Specification
Component Material BS EN
Body DZR Brass 12165 CW602N
Dimensions
Nominal Size mm 15 (Fig 149) 22 (Fig 149) 15 (Fig 249C)
A mm 40 41.5 61.4
B mm 10.5 10.5 9.5
C mm 15.2 22.2 15.2
D mm 57 58.5 78.5
E mm - - 24.5
Weight (appr) kg 0.100 0.170 0.116
A
B B
C
E
Fig. 149 Fig. 249 & 249C
Nominal Size mm 15 (Fig 249) 22 (Fig 249) 28 (Fig 249)
A mm 61.4 74.6 88.6
B mm 9.5 10.5 12.5
C mm 15.2 22.2 28.25
D mm 78.5 91.4 106.3
E mm 24.5 27.5 30.5
Weight (appr) kg 0.116 0.212 0.360
Hattersley-Section 4a 25/4/06 9:34 am Page 8
904.06
Pressure/Temperature RatingBS5154 PN32 Series A14 bar at 260ºC32 bar from -10 to 100ºC
Test Pressures (Hydraulic)Shell: 48 barSeat: 35.2 bar
SpecificationHorizontal lift patternVee-Reg disk and seatCan be fitted with spring for use in vertical pipelines (Fig. 0123NRSL)Threaded coverEnds threaded internal BS EN 10266(ISO 7)
Fig. 0123NR
Bronze Check Valves - Vee-Reg PatternPN32 Series A 1/2” - 2”
Material Specification
Specification
Component Material BS EN ASTM
Cap Bronze 1982 CC491K B62
Disk Stainless Steel 10088-1 X17CrNi16-2 AISI 431
Seat Stainless Steel 10088-1 X17CrNi16-2 AISI 431
Body Bronze 1982 CC491K B62
Dimensions
Nominal Size in 1/2 3/4 1 11/4 11/2 2
A mm 73 89 95 114 124 148
B mm 42 51 57 68 75 86
Weight kg 0.5 0.7 1.1 1.7 2.4 2.4
A
B
Hattersley-Section 4a 25/4/06 9:34 am Page 9
10 04.06
A
B
Pressure/Temperature RatingBS5154 PN32 Series B14 bar at 198ºC32 bar from -10 to 100ºC
Test Pressures (Hydraulic)Shell: 48 barSeat: 35.2 bar
SpecificationSizes 1/2 to 2in figure 1013 Horizontal lift patternThreaded coverDisk (renewable) for steam serviceEnds threaded internal BS EN 10266(ISO 7)
Fig. 1013
Bronze Check Valves - Horizontal Lift PatternPN32 Series B 1/2” - 2”
Satura
ted
Stea
m
0 40 80 120 160 200 240 Temperature ˚C
28
24
20
16
12
4
0
Pre
ssur
e ba
r
8
32
36
Material Specification
Specification
Component Material BS EN
Cap Bronze 1982 CC491K
Disk Holder Bronze 1982 CC491K
Disk (Renewable) Glass Fibre Filled PTFE Teflon
Body Bronze 1982 CC491K B62
Dimensions
Nominal Size in 1/2 3/4 1 11/4 11/2 2
A mm 60 74 86 99 109 130
B mm 39 43 51 58 64 70
Weight kg 0.4 0.6 1.1 1.3 2.1 3.4
Hattersley-Section 4a 25/4/06 9:34 am Page 10
1104.06
Pressure/Temperature RatingBS5154 PN32 Restricted32 bar from -10 to 90ºC
Test Pressures (Hydraulic)Shell: 48 barSeat: 35.2 bar
SpecificationHorizontal lift patternThreaded coverRenewable nitrile diskAlternative disk materials availableFitted with 6kPa head rated recoil springEnds threaded internal BS EN 10266(ISO 7)Available with NPT thread (1213AT).Material Specification
Specification
Component Material BS EN
Cap (1/2 to 1in) Brass 12165 CW617N
(11/4 to 2in) Brass 1982 CC754S
(21/2 to 3in) Bronze 1982 CC491K
Recoil Spring Stainless Steel (6 kPa head rating)
Disk Case (1/2 to 1in) Brass 12164 CW614N
(11/4 to 3in) Bronze 1982 CC491K
Disk Nitrile
Disk Nut (1/2 in) Brass 12164 CW614N
(3/4 to 3in) Bronze 1982 CC491K
Body Bronze 1982 CC491K
Dimensions
Nominal Size in 1/2 3/4 1 11/4 11/2 2
A mm 60 70 83 98 106 132
B mm 40 45 55 60 70 80
Weight kg 0.4 0.7 1.1 1.6 2.2 3.6
0 20 40 60 80 100 120 140Temperature ˚C
28
24
20
16
12
4
0
Pre
ssur
e ba
r
8
32
36
A
B
Fig. 1213
Bronze Check Valves - Horizontal Lift With RecoilSpring PN32 (Restricted to a max temp of 90ºC)
Hattersley-Section 4a 25/4/06 9:34 am Page 11
12 04.06
A
B
Pressure/Temperature RatingBS5154 PN2525 bar from -10 to restricted 90ºC
Test Pressures (Hydraulic)Shell: 37.5 barSeat: 27.5 bar
SpecificationHorizontal swing patternThreaded coverAlternative disk materials availableEnds threaded internal BS EN 10266(ISO 7)Available with NPT thread (3047AT)Suitable for mounting in horizontal and vertical pipe (with vertical flow upwards).
Fig. 3047
Bronze Check Valves - Swing Pattern PN25
Material Specification
Specification
Component Material BS EN ASTM
Body Bronze 1982 CC491K
Cap Bronze 1982 CC491K
Disc Holder (1/2 to 1in) Brass 12164 CW614N
(11/4 to 2in) Bronze 1982 CC491K
Disc Nitrile Rubber 2751 - BA80
Disc Retaining Nut Brass 12164 CW614N
Disc Retaining Washer Brass 12164 CW614N
Hinge Bronze 1982 CC491K
Hinge Pin Stainless Steel 970 GR316S11
Hinge Nut Brass 12164 CW614N
Identity Plate Aluminium
Drive Screw Steel - Electro Brassed
Dimensions
Nominal Size in 1/2 3/4 1 11/4 11/2 2
A mm 58 66 80 89 95 108
B mm 38 42 49 56 65 76
Weight kg 0.33 0.43 0.63 1.01 1.34 2.12
Hattersley-Section 4a 25/4/06 9:34 am Page 12
1304.06
Pressure/Temperature Rating16 bar up to 120ºC
Test Pressure (Hydraulic)Shell: 24 barSeat: 17.6 bar
SpecificationWafer bodySoft seat50 to 300mm sizes suitable for flangesto BS EN 1092-2 PN16:Valves to suit other flangespecifications available.
Fig. 5870
Aluminium Bronze WaferThin™ Check ValvesPN16 up to 120ºC
0 20 40 60 80 100 120 140Temperature ˚C
14
12
10
8
6
2
0
Pre
ssur
e ba
r
4
16
18
Material Specification
Specification
Component Material BS EN ASTM
Body (50 to 100mm) Aluminium Bronze 12163 CW307G B150-673000
(125 to 600mm) Aluminium Bronze 1982 CC333G B148-C95800
Disk Aluminium Bronze 1982 CC333G B148-C95800
O-ring EPDM
Hinge Pin Stainless Steel 10088-1 X2 CrNiMo17-12-2 A276-316L
Retaining Plate Stainless Steel 10088-1 X2 CrNiMo17-12-2 A276-316L
Screw Stainless Steel 10088-1 X2 CrNiMo17-12-2 A276-316L
Lifting Eye Stainless Steel
Nut Stainless Steel
Dimensions
Nominal Size mm 50 65 80 100 125 150 200 250 300 350
A mm 97 110 127 159 189 208 273 330 380 446
B mm 16 16 23 23 19 23 23 30 32 38
C mm 30 36.5 46 66 91 116 143 191 216 263
Weight (appr) kg 0.9 1.0 2.0 3.7 5.0 5.8 14 19 32 40A
B
C
Hattersley-Section 4a 25/4/06 9:34 am Page 13