bsr 2000 - release 1.1 - hardware installation guide

BSR 2000 Installation Guide

526359-001-00 Rev BRelease 1.1

NoticeCopyright © 2011Motorola Mobility, Inc.All rights reserved

No part of this publication my be reproduced in any form or by any means or used to make and any derivative work (such as translation, transformation or adaptation) without written permission from Motorola Mobility, Inc.

Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Motorola may make improvements or changes in the product(s) described in this manual at any time.

Motorola and the stylized M logo are registered trademarks of Motorola, Inc. Broadband Services Router, BSR, BSR 64000, RiverDelta, and SmartFlow are trademarks of Motorola, Inc. All other trademarks and registered trademarks are the property of their respective owners.

Caring for the Environment by RecyclingWhen you see this symbol on a Motorola product, do not dispose of the product with residential or commercial waste.Recycling your Motorola EquipmentPlease do not dispose of this product with your residential or commercial waste. Some countries or regions, such as the European Union, have set up systems to collect and recycle electrical and electronic waste items. Contact your local authorities for information about practices established for your region. If collection systems are not available, call Motorola Customer Service for assistance.

526359-001-00 Rev BRelease 1.1

Published: 2/11

Regulatory Compliance

Special Symbols That Might Appear on the Equipment

These servicing instructions are for use by qualified personnel only. To reduce the risk of electrical shock, do not perform any servicing other than that contained in the Installation and Troubleshooting Instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.

This symbol indicates that dangerous voltage levels are present within the equipment. These voltages are not insulated and may be of sufficient strength to cause serious bodily injury when touched. The symbol may also appear on schematics.

The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important installation, servicing, and operating instructions in the documents accompanying the equipment.

CAUTIONRISK OF ELECTRIC SHOCK

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).NO USER-SERVICEABLE PARTS INSIDE.

CAUTION:

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

CAUTION: TO ENSURE REGULATORY AND SAFETY COMPLIANCE, USE ONLY THE PROVIDED POWER CABLES.

It is recommended that the customer install an AC surge arrestor in the AC outlet to which this device is connected. This is to avoid damaging the equipment by local lightning strikes and other electrical surges.

This equipment operates over the marked Voltage and Frequency range without requiring manual setting of any selector switches. Different types of line cord sets may be used for connections to the mains supply circuit and should comply with the electrical code requirements of the country of use. This equipment reqires a grounding conductor in the line cord. The North American line cord provided with the equipment is acceptable for use with NEMA Style 5-15 AC receptacles supplying nominal 120 Volts.

FCC ComplianceThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial or residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Installation Manual or instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. Any changes or modifications not expressly approved by Motorola could void the user’s authority to operate this equipment under the rules and regulations of the FCC. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:Re-orient or relocate the receiving antennaIncrease the separation between the equipment and receiverConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.You may find the following booklet, prepared by the Federal Communication Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems, Stock No. 004-000-0342-4, U.S. Government Printing Office, Washington, DC 20402.Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CablesThis equipment is designed for use with properly shielded and terminated Intra-Bulding cables. Electrical connection to external cables must be made only through isolation devices. Refer to the installation section of this manual before operation.

FCC Declaration of ConformityAccording to 47 CFR, Parts 2 and 15 for radio frequency devices, Motorola, Inc. 111 Locke Drive, Marlborough, MA 01752 declares under sole responsibility that the product identifies with 47 CFR Part 2 and 15 of the FCC Rules as a Class B digital device. Each product marketed is identical to the representative unit tested and founded to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47 CFR 2.909. Operation is subject to the following condition: This device must accept any interference received, including interference that may cause undesired operation. The above named party is responsible for ensuring that the equipment complies with the standards of 47 CFR, Paragraphs 15.107 to 15.109.

Canadian ComplianceThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.Cet appareil numérique de la classe B respects toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Laser SafetyAll Motorola, Inc. systems equipped with laser products are Class 1 Laser Products in compliance with IEC 60825 and CDRH 21 CFR 1040.10 and 1040.11

CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure

Declaration of ConformityWeMotorola, Inc.111 Locke DriveMarlborough, MA 01752, U.S.A.

declare under our sole responsiblity that the

Broadband Services Router Model: BSR 2000

to which this declaration relates is in conformity with one or more of the following standards:

EMC Standards

EN 300 386 V.1.3.1:2001, CISPR 22:1997 +A1:2000 +A2:2002, EN 50083-2:2001

Safety Standards

EN 60950-1:2002, IEC 60950-1:2001, EN 60825:, IEC 60825:

following the provisions of the Directive(s) of the Council of the European Union:

EMC directive 89/336/EEC Low Voltage Directive 73/23/ECC

VCCI Statement

Korean MIC Statement

Russian GOST

Safety Standards and Emissions StandardsThe BSR 2000 is designed to meet GR-1089-CORE:1999 and complies with the following specifications.

Safety• UL 60950-1 1st Edition:2003• CSA 22.2 No 60950-1-03 1st Edition:2003• EN 60950-1 1st Edition:2002• IEC 60950-1 1st Edition:2001• EN 60825-1: 2002• EN 60825-2: 2000• EN 60950-2: 2000• IEC 60825-1 Edition 1.2:2001• IEC 60825-2 Edition 2:2002• CDRH 21 CFR 1040.10 and 1040.11

Emissions• 47 CFR Part 15:2004 Class B• ICES-003:2004 Class B• EN 300 386 V1.3.1:2001 Class B• EN 55022:2003 Class B• VCCI V3:2004 Class B• CISPR 22: 1997 +A1:2000 +A2: 2002 Class B• AS/NZ CISPR 22:2002 Class B• Korean MIC Notice 2005-82: 2005 Class B

Immunity• EN 300 386 V1.3.1:2001• EN 55024:2003• CISPR 24:2002• Korean MIC Notice 2005-83:2005

EnvironmentalThe BSR 2000 is designed to meet the following specifications.

• EN 300 019• EN 300 119• GR-63-CORE: 1995

526359-001-00 Rev B xiii

Contents

PrefaceScope ..........................................................................................................................................xviiAudience.....................................................................................................................................xviiDocumentation Set .....................................................................................................................xviiConventions...............................................................................................................................xviiiNotes, Cautions, Warnings ..........................................................................................................xixIf You Need Help.......................................................................................................................... xx

Telephone Support..........................................................................................................3-xxOnline Support...............................................................................................................3-xxi

Motorola BSR Customer Website ...................................................................3-xxi

1 BSR 2000 Product Description

2 Performing Installation TasksOverview .....................................................................................................................................2-1Preinstallation Tasks....................................................................................................................2-2

Installation Accessories ....................................................................................................2-2Required Tools and Equipment ........................................................................................2-2

Inspecting the Installation Site ....................................................................................................2-3Site Installation Options ..............................................................................................................2-3

Equipment Rack Choices .................................................................................................2-3Mounting the BSR 2000 in an Equipment Rack .........................................................................2-4

Rack Mounting Options ...................................................................................................2-4Before You Begin .............................................................................................................2-4

BSR 2000 Installation Guide Release 1.1

xiv 526359-001-00 Rev B

Rack-Mounting Procedure................................................................................................2-4Marking the Installation Location on the Equipment Rack ...............................2-4Attaching the Mounting Brackets ......................................................................2-4Mounting and Securing the BSR 2000 in an Equipment Rack..........................2-6

Setting up the BSR 2000 for Desktop Operation ........................................................................2-7Before You Begin .............................................................................................................2-7Installing the BSR 2000 on a Desktop .............................................................................2-8

Connecting Network Cables........................................................................................................2-8Connecting an Ethernet Cable to the BSR 2000 ..............................................................2-9Connecting a Cable to the Redundant Ethernet Port on the BSR 2000..........................2-10Connecting Gigabit Ethernet Cables to the BSR 2000...................................................2-11Connecting a Cable to the T1/E1 BITS Interface...........................................................2-13Connecting Coaxial Cables to the BSR 2000.................................................................2-14

Connecting a Coaxial Cable to the Downstream Channel Port .......................2-14Connecting Coaxial Cables to the Upstream Channel Ports............................2-14Connecting a Coaxial Cable to the Wireless Port ............................................2-15

Setting up a Console Monitor....................................................................................................2-16Configuring Communications Parameters .....................................................................2-17Connecting a Console Monitor.......................................................................................2-17

Replacing the Compact Flash Memory Card ............................................................................2-18Connecting the BSR 2000 to a Power Source...........................................................................2-20Determining Successful Booting...............................................................................................2-21Interpreting LED Displays ........................................................................................................2-22

Power LED .....................................................................................................................2-22System LEDs ..................................................................................................................2-23R/W LED........................................................................................................................2-23Upstream and Downstream Port LEDs ..........................................................................2-24Network LEDs................................................................................................................2-25Rear Panel Ethernet Port LEDs ......................................................................................2-26T1/E1 BITS LED............................................................................................................2-28Power Status LED ..........................................................................................................2-29

Rebooting the System................................................................................................................2-30Where To Go From Here...........................................................................................................2-31

Release 1.1

526359-001-00 Rev B xv

A SpecificationsOverview ....................................................................................................................................A-1Physical ......................................................................................................................................A-1Electrical.....................................................................................................................................A-2Environmental ............................................................................................................................A-2Network Interfaces .....................................................................................................................A-2SFP Module Specifications ........................................................................................................A-2RF Spectrum...............................................................................................................................A-4Timing Generation .....................................................................................................................A-4

B Connector PinoutsOverview .................................................................................................................................... B-1Console Port Connector ............................................................................................................. B-110/100 Ethernet Port Connectors ............................................................................................... B-3Gigabit Ethernet Port Connector ................................................................................................ B-4T1/E1 BITS Connector...............................................................................................................B-5Redundant Port Connector ......................................................................................................... B-6

C Safety Warnings, Cautions, and GuidelinesOverview .................................................................................................................................... C-1Safety Warnings and Cautions ...................................................................................................C-1

Qualified Personnel Caution............................................................................................ C-2Installation Warning ........................................................................................................ C-2Rack-Mounting Caution .................................................................................................. C-2Stacking Caution ............................................................................................................. C-2SELV Circuit Warning..................................................................................................... C-2Operating Temperature Caution ...................................................................................... C-3Electrical Safety Warning................................................................................................ C-3Electrical Grounding Warning......................................................................................... C-3Grounded Equipment Warning........................................................................................ C-3LED Product Caution ...................................................................................................... C-3Laser Safety Caution ....................................................................................................... C-4Product Disposal Caution ................................................................................................ C-4Lightning Activity Warning............................................................................................. C-4


xvi 526359-001-00 Rev B

Jewelry Removal Caution................................................................................................ C-4Safety Guidelines ....................................................................................................................... C-5

Electrical Safety Guidelines ............................................................................................ C-6In Case of Electrical Accident .......................................................................... C-6

Index

526359-001-00 Rev B xvii

Preface

ScopeThis document describes how to install the Motorola™ Broadband Services Router™ 2000 (BSR 2000™).

AudienceThis document is for use by those persons who will install and configure the BSR 2000™ product. Only trained service personnel should install, maintain, or replace the BSR 2000.

Documentation SetThe following documents comprise the BSR 2000 documentation set:

n BSR 2000 Installation Guide

This document describes how to install the BSR 2000 product.

n BSR 2000 Configuration and Management Guide

This document provides the instructions and procedures for configuring and managing the BSR 2000.

n BSR 2000 Command Reference Guide

This document contains descriptions of the Command Line Interface (CLI) commands for managing, configuring, and maintaining the BSR 2000.


xviii 526359-001-00 Rev B

n BSR 2000 SNMP MIB Reference Guide

This document describes the Simple Network Management Protocol (SNMP) MIBs; provides information that describes standard and proprietary MIB support; describes how to walk the MIBs and how to compile and load the SNMP MIBs. It also provides task examples.

n BSR 2000 Release Notes

These documents provide information about features not described or incorrectly documented in the main documentation set; known problems and anomalies; product limitations; and problem resolutions.

ConventionsThis document uses the conventions in the following table:

Convention Example Explanation

angle brackets < > ping <ip-address> ping 54.89.145.71

Arguments in italic and enclosed by angle brackets must be replaced by the text the argument represents. In the example, 54.89.345.71 replaces <ip-address>. When entering the argument, do not type the angle brackets.

bar brackets [ ] disable [level] Bar brackets enclose optional arguments. The example indicates you can use the disable command with or without specifying a level. Some commands accept more than one optional argument. When entering the argument, do not type the bar brackets.

bold text cable relay-agent-option Boldface text must be typed exactly as it appears.

brace brackets {} page {on | off} Brace brackets enclose required text. The example indicates you must enter either on or off after page. The system accepts the command with only one of the parameters. When entering the text, do not type the brace brackets.

italic text boot system <filename> Italic type indicates variables for which you supply values in command syntax descriptions. It also indicates file names, directory names, document titles, or emphasized text.

Release 1.1 Preface

526359-001-00 Rev B xix

Notes, Cautions, WarningsThe following icons and associated text may appear in this document.

screen display Wed May 6 17:01:03 2000

This font indicates system output.

vertical bar | page {on | off} A vertical bar separates the choices when a parameter is required. The example indicates you can enter either command: page on or page offWhen entering the parameter, do not type the vertical bar or the brace brackets.

Note: A note contains tips, suggestions, and other helpful information, such as references to material not contained in the document, that can help you complete a task or understand the subject matter.

Caution: The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important installation, servicing, and operating instructions in the documents accompanying the equipment.

Warning: This symbol indicates that dangerous voltages levels are present within the equipment. These voltages are not insulated and may be of sufficient strength to cause serious bodily injury when touched. The symbol may also appear on schematics.

Convention Example Explanation


xx 526359-001-00 Rev B

If You Need HelpSupport for your BSR 2000 hardware and software is available via telephone and the Internet.

Telephone SupportIf you need assistance while working with the BSR 2000, contact the Motorola Technical Response Center (TRC):

The Motorola TRC is on call 24 hours a day, 7 days a week.

When calling for technical support, please have the following information available:

n Your customer information, including location, main contact, and telephone number

n BSR product and modulesn Detailed description of the issuen Specific information to assist with resolving the problem, including:

• BSR hostname• BSR error messages and logs• Output of BSR show tech command• Cable modem information

n List of troubleshooting steps you have performed before calling the TRC.n Current state of your BSR 2000 productn Severity of the issue you are reporting

When calling for repair or Advanced Component Exchange (ACE) replacement, please provide the following additional information:

n Output of BSR show version command, with part numbers and serial numbers of BSR components

n Shipping information for the replacement, including contact name, company name, address, phone number, and email address

U.S. 1-888-944-HELP (1-888-944-4357)

International +215-323-0044

Release 1.1 Preface

526359-001-00 Rev B xxi

Online Support

Motorola BSR Customer Website The BSR customer website, http://bsr.motorola.com, is available for BSR customers with active service contracts to access the latest product information, software updates, troubleshooting information, and technical publications for the BSR 64000, BSR 2000, and BSR 1000 product line.

You may request access to the site by emailing the BSR product support team at [email protected] with the following information:

n Company namen Contact name, phone number, and email addressn Motorola Support contactn BSR product under service contract

The BSR product support team will email an invitation to you with further instructions on how to set up an account on the BSR customer information website.


xxii 526359-001-00 Rev B

526359-001-00 Rev B 1-1

1BSR 2000 Product Description

The Broadband Services Router™ 2000 (BSR 2000™) from Motorola, shown in Figure 1-1, is a compact Cable Modem Termination System (CMTS) and router housed in a 1U height stackable enclosure.

The BSR 2000 complements the higher-capacity, carrier-class BSR 64000. The BSR 2000 is designed for smaller distribution hubs or larger sites in the early stages of providing expanded broadband services where the BSR 64000 is not required.

The BSR 2000 operates as either a CMTS/router or as a CMTS/Layer 2 bridge.

The BSR 2000 is based on Data Over Cable Service Interface Specification (DOCSIS) 2.0 and PacketCable 1.0 standards. It provides two Gigabit and four autosensing 10/100 BASE-T Ethernet ports for network access, one 10/100 BASE-T port for redundancy support, one T1/E1 port for BITS recovery, and four upstream channels and one downstream channel for DOCSIS connectivity.

The BSR 2000 enables Multiple System Operators (MSOs) to expand their service area and deliver the traffic shaping, isolation, and policing needed to enable end-to-end Service Level Agreements (SLAs) across a Hybrid Fiber coax (HFC) network infrastructure.

Combined with CLI management and Motorola service creation software, the BSR 2000 allows an MSO to allocate bandwidth on their HFC network infrastructure among multiple service providers, and to provide data, voice, and multimedia services to their subscribers.


1-2 526359-001-00 Rev B

Figure 1-1 The BSR 2000

Front View

STS

DOWNSTREAM UPSTREAM NETWORK

ALM0 1 1

0

2 3

2

3 5

4

0SYSTEM

PWR FAIL STS ALM RED BSR 2000

CONSOLE

R/W RESET

PowerLED

LEDs for downstream port

LEDs for upstream

ports

SystemLEDs

R/WLED

Reset buttonNetwork

LEDs

RS-232 console port

Flash card cover

Rear View

US2US1US0DS0IF

10 2 3 54

T1/E1 BITS connector

10/100 Ethernet

ports

Redundant 10/100 port

GIG-E SFP ports

Wireless connector

Downstream port (Type F connector)

AC power receptacle

Power switch

Power Status LEDUpstream ports

(Type F connector)

US3

bsr2k019

RED Bits

526359-001-00 Rev B 2-1

2Performing Installation Tasks

OverviewThis chapter provides information about the following topics.

n Preinstallation Tasksn Inspecting the Installation Siten Site Installation Optionsn Mounting the BSR 2000 in an Equipment Rackn Setting up the BSR 2000 for Desktop Operationn Connecting Network Cablesn Setting up a Console Monitorn Replacing the Compact Flash Memory Cardn Connecting the BSR 2000 to a Power Sourcen Determining Successful Bootingn Interpreting LED Displaysn Rebooting the System


2-2 526359-001-00 Rev B

Preinstallation TasksPreinstallation tasks include:

n Confirming that you have the accessories to perform the installation procedures.n Obtaining the items you need to complete the installation procedures.

Installation AccessoriesIn addition to this document and the product release notes, the BSR 2000™ shipment includes the following items:

n Two rack-mounting bracketsn Eight flathead #10-32 x 7/16 Phillips screwsn One 8-ft. (2.4-m) US power cordn One 8-ft. (2.4-m) country-specific power cord (if required)n Four rubber feet for desktop installation n One CD-ROM containing online customer documentationn Release Notes

Required Tools and EquipmentTo perform the rack-mount or desktop installation procedures, you need the following items. Motorola does not provide these items; you must obtain them yourself.

n A #2 Phillips screwdriver (for rack-mount installations only)n A terminal or PC with terminal emulation softwaren A shielded RS-232 crossover cable with a female DB-9 pin connector and a

connector compatible with the RS-232 port on the terminal or PCn Ethernet patch cables with male RJ-45 connectors for the 10/100 Ethernet portsn Ethernet patch cables with either male LC connectors or male RJ-45 connectors

(depending on whether the SFP module is copper-based or fiber-based) for the Gigabit Ethernet ports

n Coaxial cable to connect the BSR 2000 to the wireless portn Coaxial cables for the upstream and downstream connectionsn Antistatic wrist strap or antistatic foot strapn Hardware (mounting screws, threaded clips, etc.) to secure the BSR 2000 in an

equipment rack

Release 1.1 Performing Installation Tasks

526359-001-00 Rev B 2-3

Inspecting the Installation SiteInspect the BSR 2000 installation site to ensure the following:

n At least 3 in. (7.5 cm) clearance exists on the sides of the BSR 2000 to allow for adequate airflow for component cooling.

n At least 3 ft. (1 m) exists at the front and rear panels to connect the Ethernet cables, upstream and downstream cables, wireless cable, RS-232 Console Monitor cable, and power cord.

n The BSR 2000 will be installed within 8 ft. (2.4 m) of an AC power outlet.n When mounting the BSR 2000 in an equipment rack, inspect the equipment rack

to determine if it is installed according to the manufacturer’s instructions and is grounded in accordance with all local, state, and national codes.

n When setting up the BSR 2000 for desktop operation, confirm that the desktop is flat, level, and stable and can support 20 lbs. (9 kg). Also confirm that power and network cables connected to the BSR 2000 will run in areas that will be undisturbed during operation.

Site Installation OptionsThe BSR 2000 offers the following site installation options:

n Mounting in an equipment rack (front mount or mid mount)n Desktop installation

Equipment Rack ChoicesWhen you choose to mount the BSR 2000 in an equipment rack, Motorola recommends using one of the following equipment racks:

n Standard 7 ft. high, 19-inch equipment racks NEBS or 2200mm ETS1 wide racksn Standard 4-post Telco equipment rack.

Note: You can also place the BSR 2000 on a shelf in an equipment rack. If you do so, you must attach the rubber feet (found in the BSR 2000 accessory bag) to the BSR 2000. Refer to the section, Setting up the BSR 2000 for Desktop Operation, later in this document.


2-4 526359-001-00 Rev B

Mounting the BSR 2000 in an Equipment RackThe BSR 2000 provides rack-mounting brackets for mounting the unit in a standard 19-in. equipment rack.

Rack Mounting OptionsYou can choose from the following mounting options.

n Front mountn Mid mount

Before You BeginBefore you begin the rack-mounting procedures, make sure of the following:

n You have all tools and other equipment required to complete the installation.n You are wearing an anti-static wrist strap or foot strap.n You choose a mounting option.

Rack-Mounting ProcedureTo mount the BSR 2000 in an equipment rack, perform the following tasks:

1. Mark the location on the rack where you intend to mount the BSR 2000

2. Attach the mounting brackets to the sides of the BSR 2000 chassis.

3. Mount and secure the BSR 2000 in its equipment rack.

The following sections describe these tasks.

Marking the Installation Location on the Equipment RackThe BSR 2000 is a 1U-height device that is designed to straddle the 1/2-in. spaced holes in a standard 19-in. equipment rack.

Using a pencil (or other erasable marker), mark the location on the rack where you will mount the BSR 2000.

Attaching the Mounting BracketsThe BSR 2000 utilizes custom left and right mounting brackets, designed to maximize airflow through the chassis to maintain proper cooling of the internal components. The brackets are shown in Figure 2-1.


526359-001-00 Rev B 2-5

Figure 2-1BSR 2000 Left and Right Mounting Brackets

To attach the mounting brackets, follow these steps and refer to Figure 2-2.

1. Match and align the mounting bracket holes with the threaded holes at the position for the mounting option you selected.

Be sure to use the left bracket on the left side of the BSR 2000 and the right bracket on the right side of the BSR 2000.

2. Insert screws through the rack mounting holes into the threaded holes on the side of the BSR 2000.

3. Tighten the screws with a Phillips screwdriver.

bsr2k040

Right mounting bracket

Left mounting bracket


2-6 526359-001-00 Rev B

Figure 2-2 Attaching Mounting Brackets to the BSR 2000

Mounting and Securing the BSR 2000 in an Equipment RackTo mount and secure the BSR 2000 in an equipment rack, follow these steps. Figure 2-3 shows a front-mounted BSR 2000.

1. Lift and hold the BSR 2000 at its intended position in the rack and align the BSR 2000 mounting bracket holes with the mounting holes of the equipment rack.

2. Secure the BSR 2000 in the equipment rack.

Note: Motorola recommends that you use two people to perform the rack-mounting procedure. One person should hold the BSR 2000 in position while the other secures it in the equipment rack.

bsr2k003Mid Mount

Front Mount

STS


ALM0 1 1

0

2 3

2

3 5

4

0SYSTEM


CONSOLE

R/W RESET

STS


ALM0 1 1

0

2 3

2

3 5

4

0SYSTEM


CONSOLE

R/W RESET


526359-001-00 Rev B 2-7

Figure 2-3 Securing the BSR 2000 in an Equipment Rack (all mounting options)

Setting up the BSR 2000 for Desktop OperationThe BSR 2000 can operate as a desktop device in environments where mounting in an equipment rack is not required or impractical.

A suitable surface for placement of the BSR 2000, must meet the following requirements:

n Flat, level, and securen Capable of supporting 20 lbs (9 kg)

Before You BeginBefore you operate the BSR 2000 on a desktop, make sure of the following:

n You have all tools and other items required to complete the installation, including the four rubber feet found in one of the BSR 2000 accessory bags.

n You are wearing an antistatic wrist strap or foot strap.

bsr2k016

Mid Mount

Front Mount

STS


ALM0 1 1

0

2 3

2

3 5

4

0SYSTEM


CONSOLE

R/W RESET

STS


ALM0 1 1

0

2 3

2

3 5

4

0SYSTEM


CONSOLE

R/W RESET


2-8 526359-001-00 Rev B

Installing the BSR 2000 on a DesktopTo install the BSR 2000 on a desktop follow these steps:

1. Attach the four rubber feet to the bottom of the BSR 2000 in the locations shown in Figure 2-4.

Three of the rubber feet should be placed in the circular depressions shown. The fourth should be placed at the rear of the cutout area, as shown.

2. Remove each rubber foot from its protective paper (protects the adhesive side), and press it firmly so that it adheres to to the bottom of the BSR 2000 chassis.

3. Place the BSR 2000 in its intended location on the desktop.

Figure 2-4 Attaching Rubber Feet to the Bottom of the BSR 2000 Enclosure

Connecting Network CablesYou connect the following kinds of cables to the BSR 2000:

n A shielded DB-9 console cablen Shielded Twisted Pair (STP) Ethernet cables equipped with shielded RJ-45 plugsn Ethernet cables equipped with LC-type fiber optic plugsn One coaxial cable for the BSR 2000 downstream channeln Up to four coaxial cables for the BSR 2000 upstream channelsn One coaxial cable for the BSR 2000 wireless portn One shielded RJ-48 cable for the BITS interface

Placement of rubber feet

STS

DWN STRM UP STRM NETWORK

ALM0 1 1

0

2 2

2

3 3

3

0SYSTEM


CONSOLE

R/W RESET

bsr2k039

Cutout area

Circular depression


526359-001-00 Rev B 2-9

Connecting an Ethernet Cable to the BSR 2000The BSR 2000 has built-in Ethernet network interfaces for connecting to a router, switch, or hub. The RJ-45 ports for the Ethernet interfaces are located on the left side of the rear panel. The ports numbers are color-coded in purple and labeled 0,1,2 and 3 as shown in Figure 2-5.

Figure 2-5 RJ-45 Ethernet Ports

To connect the BSR 2000 to the network, follow these steps.

1. Connect a male shielded RJ-45 connector at one end of the cable to the assigned Ethernet port on the router, hub, or switch.

2. Connect a male RJ-45 connector at the opposite end of the network cable to one of the four RJ-45 Ethernet ports on the BSR 2000.

Note: To maintain regulatory compliance, use only shielded cables to connect to the BSR 2000.

To Ethernet router, switch, or hub

bsr2k005

0 1 2 3 4 5BitsRED


2-10 526359-001-00 Rev B

Connecting a Cable to the Redundant Ethernet Port on the BSR 2000

The BSR 2000 provides support for 1:1 software-based redundant operation. In redundant configuration, two BSR 2000s are interconnected via a dedicated 10/100BASE-T Ethernet link. The redundant port is labeled RED, and is color-coded in black. To connect a cable to the redundant port, follow these steps.

1. Connect a male shielded RJ-45 connector to the redundant Ethernet port. See Figure 2-6.

2. Connect the opposite end of the network cable to the redundant Ethernet port on the second BSR 2000.

Figure 2-6 Connecting a Cable to the Redundant 10/100 Port

2 3 4 5

To secondary BSR 2000

bsr2k029

1BitsRED 0


526359-001-00 Rev B 2-11

Connecting Gigabit Ethernet Cables to the BSR 2000The BSR 2000 provides two Gigabit Ethernet network interfaces, via SFP (Small Form-factor Pluggable) modules, for connecting to a router, switch, or hub. The SFP modules can be either shielded copper-based (utilizing shielded RJ-45 connectors) or fiber-based (utilizing LC connectors). The two Ethernet ports are contained within the SFP cage, which is located on the left side of the rear panel. The ports, labeled 4 and 5 and color-coded in purple, can accommodate a variety of SFP modules. To connect a cable to a Gigabit Ethernet port, follow these steps:

1. Remove the EMI plug from the SFP port by depressing the spring-loaded latch, and pulling the plug straight out of the port, as shown in Figure 2-7.

The EMI plug comes factory-installed. Save the EMI plug, just in case you need to use it again in the future.

2. Install an SFP module into one of the slots of the SFP cage until it clicks into place. See Figure 2-7.

The actual SFP module you install may vary from the one shown.

Note: The SFP modules are keyed, and can only be installed one way. For Port 4 (bottom port), the SFP module must be installed with the pin connector facing up, towards the top of the BSR chassis. For port 5 (top port), the SFP module must be installed with the pin connector facing down, towards the bottom of the BSR chassis, as shown in Figure 2-7.


2-12 526359-001-00 Rev B

Figure 2-7 Installing SFP Modules

3. Connect a cable to the connector on the SFP, as shown in Figure 2-8.

4. Connect the other end of the cable to the assigned Ethernet port on the router, hub, or switch.

5. Repeat steps 1 through 4 to install a second SFP module in the remaining Gigabit Ethernet port and connect cables to it.

Note: To maintain regulatory compliance, use only Motorola tested and approved SFP modules. Refer to the price catalog for available modules.

Note: The BSR 2000 utilizes LC connectors for its optical interfaces. To interface with equipment that utilizes SC connectors, you will need to use the appropriate LC-SC cables or adapters. Refer to the price catalog for available cables.

bsr2k041

Remove EMI plug

2 3 4 51BitsRED 0

Install SFP module


526359-001-00 Rev B 2-13

Figure 2-8 Connecting Cables to the SFP Module

Connecting a Cable to the T1/E1 BITS InterfaceThe BSR 2000 provides a Building Integrated Timing Supply (BITS) interface to recover the timing reference from either a T1 or E1-based BITS source. The BITS port, color-coded with a gold label, uses a shielded RJ-48 connector with a Shielded Twisted Pair (STP) cable. To connect a cable to the BITS interface, follow these steps.

1. Connect a male RJ-48 connector to the BITS interface port. See Figure 2-9.

2. Connect the opposite end of the network cable to a T1 or E1-based BITS source.

bsr2k024

To Ethernet router,switch, or hub

2 3 4 51BitsRED 0


2-14 526359-001-00 Rev B

Figure 2-9 Connecting a Cable to the T1/E1 BITS Interface Port

Connecting Coaxial Cables to the BSR 2000The BSR 2000 has one downstream channel and four upstream channels. The ports for these channels, shown in Figure 2-10, are located on the BSR 2000 rear panel.

Connecting a Coaxial Cable to the Downstream Channel PortTo connect cables to the downstream channel port, follow these steps and refer to Figure 2-10.

1. Identify the downstream channel connector (DS0) on the BSR 2000 rear panel.

The port is color-coded with an orange label.

2. Insert the center conductor of the downstream channel cable into the small opening at the center of the BSR 2000 downstream channel connector.

3. Secure the connection by screwing the outside cable connector housing onto the BSR 2000 downstream connector until finger tight; then using a wrench, tighten the connector one-quarter turn (15 in.-lbs when using a torque wrench).

Connecting Coaxial Cables to the Upstream Channel PortsTo connect cables to the upstream channel ports follow these steps and refer to Figure 2-10.

0 1 2 3 4 5

To T1/E1-based BITS source

bsr2k030

BITSRED


526359-001-00 Rev B 2-15

1. Identify the upstream channel number of each cable. For this example, the cables associated with upstream channels 1 and 2 (US1 and US2 respectively).

2. Match each upstream cable with its channel connector on the BSR 2000 rear panel.

The ports are color-coded with blue labels.

3. Insert the center conductor of each upstream channel cable into the small opening at the center of the BSR 2000 upstream channel connector associated with the cable.

4. Secure the connection by screwing the outside cable connector housing onto the BSR 2000 upstream connector until finger tight; then, using a wrench, tighten the connector one-quarter turn (15 in.-lbs when using a torque wrench).

Figure 2-10 Connecting Upstream and Downstream Cables to the BSR 2000 Rear Panel

Connecting a Coaxial Cable to the Wireless PortThe BSR 2000 features a wireless port, to provide IF output, on the rear panel. The port is color-coded with a green label.To connect a cable to the wireless port, follow these steps and refer to Figure 2-11.

1. Unscrew and remove the metal terminator cap from the IF connector.

The metal terminator cap comes factory-installed. Save the terminator cap, just in case you need to use it again in the future.

US2US1US0DS0IF

Downstream coaxial cable

Upstream coaxial cables

bsr2k006


2-16 526359-001-00 Rev B

2. Insert the center conductor of the coaxial cable into the small opening at the center of the BSR 2000 wireless connector.

3. Secure the connection by screwing the outside cable connector housing onto the BSR 2000 wireless connector until finger tight; then, using a wrench, tighten the connector one-quarter turn (15 in.-lbs when using a torque wrench).

Figure 2-11 Connecting a Cable to the Wireless Port

Setting up a Console MonitorYou must connect a terminal or a PC with terminal emulation software to the BSR 2000 to perform the following tasks:

n Supply the BSR 2000 with an IP address.n Configure the BSR 2000 (if you choose not to use a Telnet session).

To connect a console monitor to the BSR 2000 and communicate with it, complete the following tasks:

Note: To supply the BSR 2000 with an IP address, refer to the document, BSR 2000 Configuration and Management Guide, after you complete the tasks described in this section.

US2US1US0DS0Win

Coaxial cable

US2US1US0DS0IF

bsr2k028


526359-001-00 Rev B 2-17

n Configure the terminal or terminal emulation software communication parameters.

n Physically connect the monitor or PC to the BSR 2000.

The following sections describe these tasks.

Configuring Communications ParametersSet communications parameters on the terminal or PC with terminal emulation software as listed in Table 2-1.

Connecting a Console MonitorTo connect a terminal or PC to the BSR 2000, follow these steps and refer to Figure 2-12.

1. Connect one end of a shielded RS-232 crossover (null modem) cable to the RS-232 port on the terminal or PC.

2. Connect the other end of the shielded cable (with the female DB-9 pin connector) to the male DB-9 pin connector labeled Console Port on the front panel of the BSR 2000.

Table 2-1 Console Monitor Communications Parameters

Parameter Setting

Baud Rate 9600

Data bits 8

Stop Bits 1

Parity None (No parity)

Flow Control None


2-18 526359-001-00 Rev B

Figure 2-12 Connecting a Console Monitor to the BSR 2000

Replacing the Compact Flash Memory CardThe BSR 2000 uses a 128 MB Compact Flash (CF) memory card, installed at the factory, to store configuration files and software updates. The Compact Flash card is hot-pluggable, and may be removed or replaced without powering down the BSR 2000. The Compact Flash card slot is located behind a removable access door on the front panel.

To remove or replace a Compact Flash memory card, follow these steps:

1. Remove the flash card cover by using a flat-head screwdriver to loosen the captive screw. See Figure 2-13.

The flash card cover swings out towards you.

2. Push the ejector button, located to the left of the flash card connector. See Figure 2-14.

3. Pull the flash card straight out of the connector. See Figure 2-14.

The flash card cover was designed to double as a removal tool. If you have trouble grasping the edge of the flash memory card, use the hooks provided at the end of the flash card cover to hook onto the tab on the underside of the flash memory card and pull it out.

NETWORK

1

0

3

2

5

4

To terminal, PC, or workstation

DB-9 RS-232 crossover connector

CONSOLE

��


526359-001-00 Rev B 2-19

4. To re-install a Compact Flash memory card, line the card up properly with the connector (it is keyed and can only be inserted one way).

5. Push the card in firmly, until it seats into the connector.

6. Replace the flash card cover and tighten the captive screw to secure it.

Figure 2-13 Removing the Flash Card Cover

BSR 2000

CONSOLE

R/W RESET

bsr2k026

R/WLED


2-20 526359-001-00 Rev B

Figure 2-14 Ejecting the Compact Flash Card

Connecting the BSR 2000 to a Power SourceThe BSR 2000 operates on AC power that it receives through an autoranging power supply.

The circuit to which you connect the BSR 2000 must provide power within the following range: 100 - 240 VAC. Figure 2-15 shows the power cord connection to the BSR 2000.

Hooks

Compact flash memory card

Ejector button

BS

R 20 00

CO

NS

OL

E

R/W

RE

SE

T

bsr2k027

Side View

Flash Card Tab

Flash Card Cover

Hook


526359-001-00 Rev B 2-21

To connect the BSR 2000 to a power source, follow these steps:

1. Make sure the BSR 2000 power switch is in the Off (O) position. See Figure 2-15.

2. Connect the AC power cord to the power receptacle located on the rear panel of the BSR 2000.

3. Connect the other end of the power cord to the AC power outlet.

4. To apply power to the BSR 2000, press the BSR 2000 power switch to the On (I) position.

Figure 2-15 Connecting a Power Cable to the BSR 2000

Determining Successful BootingAfter powering on the BSR 2000, observe the LEDs on its front panel. The LED display varies until the BSR 2000 is booted. When the booting process completes, the LEDs should display as follows:

n The System Status LED is greenn All per-port Status LEDs are green

bsr2k009

To AC power source


2-22 526359-001-00 Rev B

Interpreting LED DisplaysThe BSR 2000 provides LEDs to indicate its operational status. The following sections describe the LEDs:

n Power LEDn System LEDsn R/W LEDn Upstream and Downstream Port LEDsn Network LEDsn Rear Panel Ethernet Port LEDsn Power Status LED

Power LEDThe Power LED is a green LED, located on the front panel, as shown in Figure 2-16. The Power LED is lit when the BSR 2000 is connected to an AC power source and the power switch is in the On (I) position.

Figure 2-16 Power and System LEDs

Note: If the LEDs do not match the description in this section refer to Interpreting LED Displays, in the next section.

STS


ALM0 1 1

0

2 3

2

3 5

4

0SYSTEM

PWR FAIL STS ALM RED

PowerLED

SystemLEDs

bsr2k036


526359-001-00 Rev B 2-23

System LEDsThe BSR 2000 system LEDs are located on the left side of the BSR 2000 front panel, as shown in Figure 2-16, and are labeled FAIL (Failure), STS (Status), ALM (Alarm), and RED (Redundancy).

Table 2-2 describes the possible display states of these LEDs during operation.

R/W LEDThe BSR 2000 features a green R/W LED located on the right side of the front panel, as shown in Figure 2-17. The R/W LED is associated with the Flash Memory card, and lights to indicate Read or Write activity to or from the Compact Flash card.

Table 2-2 BSR 2000 System LED Display States

FAIL(Failure)

STS(Status)

ALM(Alarm)

RED (Redundancy) Interpretation

Off Green Off Off Normal operating status.

Off Green Yellow Off Failure. BSR 2000 is operating with an alarm condition.

Note: This LED sequence occurs when an alarm condition is detected on individual upstream and downstream ports.

Yellow Off Off Off Indicates a possible hardware failure.

Yellow Off Yellow Off Failure. BSR 2000 is not operating.

Yellow Green Yellow Off Reset. Reset button was pressed and the BSR 2000 is starting its boot process.

Off Off Off Off BSR 2000 is not receiving power or is switched Off.

Note: The System LED states described here are for a BSR 2000 running application software (steady state condition). Any of the above LED states displayed when diagnostics sequences are running are normal, and should not be interpreted as an indication of an alarm or failure condition.


2-24 526359-001-00 Rev B

Figure 2-17 BSR 2000 R/W LED

Upstream and Downstream Port LEDsThe BSR 2000 downstream port and each upstream port has two LEDs to indicate their operational status. These LEDs are located near the center of the BSR 2000 front panel and are labeled STS (Status) and ALM (Alarm), as shown in Figure 2-18.

Figure 2-18 Upstream and Downstream Port LEDs

BSR 2000

CONSOLE

R/W RESET

bsr2k034

R/WLED

STS


ALM0 1 1

0

2 3

2

3 5

4

0SYSTEM


bsr2k037

Upstream and Downstream Port LEDs


526359-001-00 Rev B 2-25

Port LEDs are grouped vertically. A number above each LED group indicates the channel number associated with the group. The single downstream channel is numbered 0 and the four upstream channels are numbered 0, 1, 2, and 3. Table 2-3 describes the possible display states of these LEDs during operation.

Network LEDsThe front panel Network LEDs, shown in Figure 2-19, are green, and illuminate to indicate the state of each of the Ethernet ports. The LEDs labeled 0 through 3 correspond to the four 10/100 Ethernet ports. The LEDs labeled 4 and 5 correspond to the two Gig-E SFP ports. Table 2-4 provides an interpretation of the LED display states.

Figure 2-19 Network LEDs

Table 2-3 BSR 2000 Downstream and Upstream Port LED Display States

STS (Status) ALM (Alarm) Interpretation

Green Off Normal operating status.

Green Amber Operating with an alarm condition detected.

Note: An alarm condition detected for an individual port also causes the System Alarm LED to light.

Off Amber Failed port. Port is not operational.

Off Off Port is not configured.

STS


ALM0 1 1

0

2 3

2

3 5

4

0SYSTEM


bsr2k042

Network LEDs


2-26 526359-001-00 Rev B

Rear Panel Ethernet Port LEDsEach of the 10/100 Ethernet ports and the Redundant (RED) port on the rear panel of the BSR 2000 has a green Link/Activity LED associated with it. The 10/100 port and Redundant port LEDs are located on the right side of each port, as shown in Figure 2-20. Each of the two Gig-E SFP ports also has an LED associated with it. These LEDs are triangular and each points at its respective SFP port. The LEDs are located in the center of the SFP cage, as shown in Figure 2-20.

Table 2-4 BSR 2000 Front Panel Network LED Display States

Network LEDs Display State Interpretation

0 through 3(10/100 ports)

On (steady) indicates a working Ethernet connection (Link) exists between the BSR 2000 and the device at the other end of the physical connection.On (blinking) indicates activity on the Ethernet port.Off indicates that a connection to the device at the other end of the physical connection is not established.

4 and 5(Gig-E SFP ports)



526359-001-00 Rev B 2-27

Figure 2-20 Rear Panel Ethernet Port LEDs

The rear panel Ethernet Port LEDs for ports 0 through 3 (the 10/100 ports) light under the same conditions as their respective front panel Network LEDs.The rear panel Ethernet Port LEDs for ports 4 and 5 (the Gig-E ports) light under different conditions as their respective front panel Network LEDs. Table 2-5 provides a definition of the LED display states.

Note: The Gig-E SFP Ports use only the outer two LEDs. The other two LEDs are not used, and will not illuminate under any conditions.

bsr2k043

Gig-E SFP Port LEDs

2 3 4 51BitsRED 0

10/100 Ethernet Port LEDs

10/100 Ethernet Port LEDs

Redundant Ethernet Port LED

SFP Cage


2-28 526359-001-00 Rev B

T1/E1 BITS LEDThe BSR 2000 T1/E1 BITS interface has a green LED associated with it, located on the rear panel to the right of the port, as shown in Figure 2-21. When lit, this LED indicates that the BSR 2000 is locked to a reference clock from a T1- or E1-based BITS source.

Table 2-5 BSR 2000 Rear Panel Ethernet Port LED Display States

Port LEDs Display State Interpretation

10/100 (Ports 0 to 3 and the Redundant port)


Gig-E(Ports 4 and 5)

For copper-based SFPs:On indicates the presence of an SFP module.Off indicates the absence of an SFP module.

For fiber-based SFPs:On indicates that an SFP module is installed with a cable connected to it, and that light is detected.Off indicates that light is not detected. This can be caused by the absence of an SFP module, the absence of a cable connected to an installed SFP module, or the absence of light when a cable is connected to an installed SFP module (the Gig-E interface could be shut down).


526359-001-00 Rev B 2-29

Figure 2-21 T1/E1 BITS LED

Power Status LEDThe BSR 2000 provides a bi-color (green/red) status LED for the power supply, located on the rear panel underneath the Power switch (see Figure 2-22).

Figure 2-22 BSR 2000 Power Status LED

0 1 2 3 4 5

T1/E1 BITS interface

bsr2k038

BITSRED

T1/E1 BITS LED

bsr2k035

Power Status LED


2-30 526359-001-00 Rev B

Table 2-6 describes the possible display states of the status LED during operation.

Rebooting the SystemThe Reset button on the BSR 2000 front panel lets you reboot the BSR 2000.

To reboot the BSR 2000, refer to Figure 2-23 and follow these steps:

1. Insert a nonconducting tool through the small hole in the BSR 2000 front panel below the RESET label, and press the Reset button.

2. Remove the tool.

Table 2-6 Status LED Display States

LED Color Interpretation

Green Power supply is operating within expected limits.

Red Indicates a problem with the power supply, for example, AC power failure, DC output loss, etc.

Note: When the power is shut down or cycled, the LED will momentarily turn red. This is normal. A steady red LED indicates a problem.

Note: The Reset button is recessed behind the BSR 2000 front panel below the Reset label. Insert a nonconducting device through the access hole on the front panel to press the Reset button.


526359-001-00 Rev B 2-31

Figure 2-23 BSR 2000 Reset Button

After you press the Reset button, the BSR 2000 reboots and the LEDs on the front panel display their boot sequence.

Where To Go From Here When you are sure that the BSR 2000 booted successfully, go to the document, BSR 2000 Configuration and Management Guide.

BSR 2000

CONSOLE

R/W RESET

bsr2k033

Reset button

526359-001-00 Rev B A-1

ASpecifications

OverviewThis appendix lists the following BSR 2000 specifications:

n Physicaln Electricaln Environmentaln Network Interfacesn SFP Module Specificationsn RF Spectrumn Timing Generation

Physicaln Form Factor: 1U heightn Height: 1.75 in. (4.45 cm)n Width: 19 in. (48.26 cm) with mounting brackets;

Chassis width: 17.25 in. (43.82 cm)n Depth: 21.75 in. (55.25 cm)n Fully configured weight: 20 lbs. (9 kg)


A-2 526359-001-00 Rev B

Electricaln Voltage: 100-240 VACn Current: 2.0 (for 100-120 VAC), 1.0 (for 200-240 VAC)n Frequency: 50/60 Hz

Environmentaln Operating temperature: 32° to 104° F (0° to 40° C)n Nonoperating temperature: -40° to 158° F (-13 to 70° C)n Operating humidity: 10-80 %, non-condensing n Nonoperating humidity, 5-95 %, non-condensing

Network Interfacesn Two Gigabit Ethernet SFP ports capable of accommodating either copper-based

or fiber-based SFP modulesn Four shielded STP (RJ-45 connector) 10/100-Mbps Ethernet portsn One additional shielded STP (RJ-45 connector) 10/100 BASE-T port for

redundancy support

SFP Module SpecificationsThis section provides specifications for the SFP modules.

Table A-1 1000BASE-SX Multi-Mode Fiber SFP Specifications

Parameter Value

Transmitter Type Shortwave laser, 850 nm

Range 550 m

Data Rate (typical) 1.250 Gbps

Connector Duplex LC

Regulatory Class 1 devices per FDA/CDRH and IEC-825-1 laser safety regulations

Release 1.1 Specifications

526359-001-00 Rev B A-3

Table A-2 1000BASE-LX Single Mode Fiber SFP Specifications

Parameter Value

Transmitter Type Longwave laser, 1310 nm

Range 10 Km


Connector Duplex LC


Table A-3 1000BASE-EX Single Mode Fiber SFP Specifications

Parameter Value


Range 40 Km


Connector Duplex LC


Table A-4 1000BASE-ZX Single Mode Fiber SFP Specifications

Parameter Value


Range 80 Km


Connector Duplex LC



A-4 526359-001-00 Rev B

RF Spectrumn Four upstream DOCSIS receivers

• Upstream modulation: QPSK, 16 QAM, 32 QAM, 64 QAM, 256 QAM• Upstream per-channel bit rate: 0.32 ~ 40.96 Mbps• Upstream input frequency range:

5 ~ 42 MHz DOCSIS5 ~ 55 MHz DOCSIS / JDOCSIS5 ~ 65 MHz EuroDOCSIS

n One downstream DOCSIS transmitter• Integrated up converter for RF output• Downstream modulation: QPSK (for wireless DOCSIS operation), 16 QAM

(for wireless DOCSIS operation), 64 QAM, 256 QAM• Downstream output frequency range: 88 ~ 857 MHz (channel center)• Output frequency step size: 125 KHz

n Wireless IF Support• Output Frequency: 44 MHz

Timing Generationn The BSR 2000 provides the capability to slave the CMTS clocks to the BITS

interface network timing reference via the rear panel port.

Table A-5 1000BASE-T Copper SFP Specifications

Parameter Value

Transmitter Type CAT 5 twisted pair

Data Rate 1000BaseT

Connector RJ-45

526359-001-00 Rev B B-1

BConnector Pinouts

OverviewThis appendix provides pinout descriptions for the following connectors:

n Console Port Connectorn 10/100 Ethernet Port Connectorsn Gigabit Ethernet Port Connectorn T1/E1 BITS Connectorn Redundant Port Connector

Console Port ConnectorThe Console Port connector shown in Figure B-1 is a male, DB-9 pin connector. Table B-1 provides the pin assignments (pinouts) for this connector.


B-2 526359-001-00 Rev B

Figure B-1 BSR 2000 Console Port

Table B-1 BSR 2000 Console Port Pin Assignments

Pin Number Name Description

Pin 1 CD Carrier Detect

Pin 2 RXD Receive Data

Pin 3 TXD Transmit Data

Pin 4 N/A Not used.

Pin 5 GND System Ground

Pin 6 N/A Not used.

Pin 7 RTS Request to Send

Pin 8 CTS Clear to Send

Pin 9 N/A Not used.

CONSOLE

Pin 1 Pin 5

Pin 6 Pin 9

bsr2k021

Release 1.1 Connector Pinouts

526359-001-00 Rev B B-3

10/100 Ethernet Port ConnectorsThe Ethernet Port connectors shown in Figure B-2 are female, RJ-45 connectors. Table B-2 provides the pin assignments for these connectors.

Figure B-2 BSR 2000 10/100 Ethernet Port Connectors

Table B-2 BSR 2000 10/100 Ethernet Port Connector Pin Assignments


Pin 1 TX+ Transmit Data +

Pin 2 TX- Transmit Data -

Pin 3 RX+ Receive Data +

Pin 4 n/c Not used.

Pin 5 n/c Not used.

Pin 6 RX- Receive Data -

Pin 7 n/c Not used.

Pin 8 n/c Not used.

Pin 8 Pin 1

Pin 1 Pin 8

bsr2k020

RED Bits 0 2 4 531


B-4 526359-001-00 Rev B

Gigabit Ethernet Port ConnectorThe Gigibit Ethernet Port connector, equipped with a copper-based SFP, is shown in Figure B-3. Table B-3 provides the pin assignments for a Gigabit Ethernet port equipped with a copper-based SFP.

Figure B-3 BSR 2000 Gigabit Ethernet Port Connector (Copper-based SFP)

Table B-3 BSR 2000 Gigabit Ethernet Pin Assignments (Copper-based SFP)


Pin 1 BI_DA+ Bi-directional pair A+

Pin 2 BI_DA- Bi-directional pair A-

Pin 3 BI_DB+ Bi-directional pair B+

Pin 4 BI_DC+ Bi-directional pair C+

Pin 5 BI_DC- Bi-directional pair C-

Pin 6 BI_DB- Bi-directional pair B-

Pin 7 BI_DD+ Bi-directional pair D+

Pin 8 BI_DD- Bi-directional pair D-

bsr2k045

2 3 4 51BitsRED 0

Pin 1Pin 8

Release 1.1 Connector Pinouts

526359-001-00 Rev B B-5

T1/E1 BITS ConnectorThe T1/E1 BITS connector, shown in Figure B-4, is a female RJ-48 connector. Table B-4 provides the pin assignments for this connector.

Figure B-4 BSR 2000 T1/E1 BITS Connector

Table B-4 BSR 2000 T1/E1 BITS Connector Pin Assignments

Pin Number Description

Pin 1 Rx Ring

Pin 2 Rx Tip

Pin 3 Not used.

Pin 4 Not used.

Pin 5 Not used.

Pin 6 Not used.

Pin 7 Not used.

Pin 8 Not used.

RED Bits 0 1 2 3 4 5

Pin 8 Pin 1

bsr2k025


B-6 526359-001-00 Rev B

Redundant Port ConnectorThe Redundant Port connector, shown in Figure B-5, is a female, RJ-45 connector. Table B-5 provides the pin assignments for this connector.

Figure B-5 BSR 2000 Redundant Port Connector

Table B-5 BSR 2000 Redundant Port Connector Pin Assignments

Pin Number Description

Pin 1 Ethernet_TXP

Pin 2 Ethernet_TXN

Pin 3 Ethernet_RXP

Pin 4 Redundancy_TXP

Pin 5 Redundancy_TXN

Pin 6 Ethernet_RXN

Pin 7 Redundancy_RXP

Pin 8 Redundancy_RXN

Note: The redundancy pairs are NOT Ethernet signals.

Pin 1 Pin 8

bsr2k044

RED Bits 0 2 4 531

526359-001-00 Rev B C-1

CSafety Warnings, Cautions,

and Guidelines

OverviewThis chapter discusses the following topics.

n Safety Warnings and Cautionsn Safety Guidelines

Safety Warnings and CautionsWarning and caution statements alert you to potential dangers when installing and maintaining the BSR 2000.

To install the BSR 2000 safely, familiarize yourself with the warnings and cautions found in the remainder of this section.


C-2 526359-001-00 Rev B

Qualified Personnel Caution

Installation Warning

Rack-Mounting Caution

Stacking Caution

SELV Circuit Warning

Caution: Only trained service personnel should install, maintain, or replace the BSR 2000.

Warning: Read the installation procedures before connecting the BSR 2000 to a power source.

Caution: When mounting the BSR 2000 in an equipment rack, avoid hazardous conditions that can result from unbalanced loading. Ensure that all equipment mounted in the rack is balanced and securely supported.

Caution: Do not stack the BSR 2000 on other BSR 2000 products or on any other equipment. If a stacked BSR 2000 falls, it can cause severe bodily injury and equipment damage

Warning: Use caution when connecting cables between devices. To avoid electrical shock, never connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits.

Release 1.1 Safety Warnings, Cautions, and Guidelines

526359-001-00 Rev B C-3

Operating Temperature Caution

Electrical Safety Warning

Electrical Grounding Warning

Grounded Equipment Warning

LED Product Caution

Caution: To prevent the BSR 2000 HD from overheating during operation, do not operate where the ambient temperature exceeds the maximum recommended ambient temperature of 122°F (50°C). To prevent airflow restriction, allow at least 3 inches (7.6 cm) of clearance around the intake and outlet ventilation openings.

Warning: Unplug the AC power cord before working on the BSR 2000.

Warning: When installing the BSR 2000, always connect the grounding first and disconnect it last when working with power cables.

Warning: The BSR 2000 must be grounded. Primary grounding occurs through its AC power cord.

Caution: The BSR 2000 is a Class 1 LED device.


C-4 526359-001-00 Rev B

Laser Safety Caution

Product Disposal Caution

Lightning Activity Warning

Jewelry Removal Caution

Caution: All Motorola, Inc. systems equipped with laser products are Class 1 Laser Products in compliance with IEC 60825 and CDRH 21 CFR 1040.10 and 1040.11. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation.

Caution: If necessary dispose of the BSR 2000 in accordance with all local, state, and national laws and regulations.

Warning: Do not install or perform maintenance tasks on the BSR 2000 or connect or disconnect any cables during lightning storms.

Caution: Before working on equipment that is connected to a power source, remove jewelry (for example, rings, necklaces, and watches). Metal objects heat up when connected to power and ground, and can cause serious injury or become welded to the power terminals.

Release 1.1 Safety Warnings, Cautions, and Guidelines

526359-001-00 Rev B C-5

Safety GuidelinesThe guidelines in this section are intended to protect you and the BSR 2000. These guidelines discuss only some of the potential hazards you might encounter while working. Be alert, and always exercise good judgement.

Perform only the procedures described in this installation guide. Make sure that only trained service personnel perform other services.

n Keep the installation area free from dust during and after installation. n Keep tools and equipment away from areas where people could trip over them

while walking. n Do not wear loose clothing or jewelry, such as rings, bracelets, or chains, which

can become caught in equipment.n Use safety glasses when working under conditions that can be hazardous to your

eyes.n Do not perform any actions that create a potential hazard to people or cause

equipment to become unsafe. n Never attempt to lift an object that is too heavy for one person to handle. n Do not install wiring during electrical storms. n Do not install electrical outlets in wet locations unless the outlets are specifically

designed for wet environments. n Replace fuses only with fuses of the same type and rating. n Do not open the BSR 2000 enclosure unless a procedure in this document

instructs you to do so. Opening the enclosure increases the risk of severe electrical shock. Only trained service personnel should open the enclosure.

n Do not insert or force any objects through the cooling vents of the BSR 2000. That action could result in electrical shock or fire.

n Avoid spilling fluids onto the BSR 2000. That action can cause electrical shock or damage the router.

n Avoid touching electrical wires or terminals that are not insulated unless theBSR 2000 is disconnected from its power source. Touching electrical wires or terminals that are not insulated could cause electrical shock.


C-6 526359-001-00 Rev B

Electrical Safety GuidelinesWhen working on electrically-powered equipment, follow these guidelines:

n Locate emergency power-off switch for the area in which you are working so that if an electrical hazard develops or an accident occurs, you can quickly turn off the power.

n Do not work alone if potentially hazardous conditions exist anywhere in your working area.

n Never assume that power is disconnected from a circuit. Always check the circuit before starting to work.

n Alert yourself to probable hazards in your work area, such as moist floors, ungrounded power extension cords, and missing safety grounds.

n Operate the BSR 2000 within its labeled electrical specifications and usage instructions.

n Install the BSR 2000 in compliance with the following local, national, or international electrical codes: • United States—National Fire Protection Association (NFPA70), United

States National Electrical Code. • Canada—Canadian Electrical Code, Part 1, CSA C22.1. • Other countries—International Electromechanical Commission (IEC) 364,

Part 1 through Part 7. • Evaluated to TN power systems.

n Observe the following guidelines for maintaining electrical safety: • Never install equipment if it appears damaged. • Periodically inspect the installation site for potential hazards such as wet

floors and for ungrounded power extension cords.

In Case of Electrical Accident If an electrical accident resulting in an injury occurs, follow these steps in the order presented:

1. Use caution. Make yourself aware of the hazards around you.

2. Disconnect power from the BSR 2000.

3. When possible, send another person to get medical aid or determine the condition of the victim, and then call for assistance.

526359-001-00 Rev B Index-1

A

attaching mounting brackets, 2-4

B

BITS connectorpinouts, B-5

booting, 2-21

C

coaxial cablesconnecting, 2-14

Compact Flash memory card, 2-18Compact Flash R/W LED, 2-23connecting a cable to the wireless port, 2-15connecting Gigabit Ethernet cables, 2-11connecting network cables, 2-8connecting the downstream channel, 2-14connecting the redundant Ethernet cable, 2-10connecting to a power source, 2-20

procedure to, 2-21connecting to the T1/E1 BITS interface, 2-13connecting upstream channels, 2-14connector pinouts, B-1console monitor

connecting to, 2-17setting communication parameters, 2-17

console monitor setup, 2-16configuring communication parameters, 2-17

connecting a console monitor to the BSR 2000, 2-17

Console port connectorpinouts, B-1

D

DB-9 pin connector, 2-2, 2-17, B-1desktop installation, 2-7downsteam modulation specification, A-4downstream channel

connecting to, 2-14downstream output frequency range, A-4Downstream port LED, 2-24

E

electrical grounding warning, C-3electrical safety warning, C-3electrical specifications, A-2

current, A-2frequency, A-2voltage, A-2

environmental specifications, A-2nonoperating humidity, A-2nonoperating temperature, A-2operating humidity, A-2operating temperature, A-2

equipmentrequired for installing, 2-2

equipment rack choices, 2-3

Index

Index-2 526359-001-00 Rev B


equipment racks, 2-3Ethernet cables

connecting, 2-9Ethernet port connectors

pinouts, B-3

F

front panel LEDsNetwork LEDs, 2-25Power LED, 2-22R/W LED, 2-23System LEDs, 2-23Upstream and Downstream port LEDs, 2-24

G

Gigabit Ethernet connectors, 2-11Gigabit Ethernet port connector

pinouts, B-4grounded equipment warning, C-3

H

humiditynonoperating, A-2operating, A-2

I

inspecting the installation site, 2-3installation

accessories, 2-2options, 2-3required tools, 2-2site inspection, 2-3

installation warning, C-2installing on a desktop, 2-8

J

jewelry removal warning, C-4

L

LED displays, 2-22downstream port, 2-24Network LEDs, 2-25Power LED, 2-22rear panel network port LEDs, 2-26System LEDs, 2-23Upstream port LEDs, 2-24

LED product warning, C-3, C-4lightning activity warning, C-4

M

mounting in an equipment rack, 2-6

N

network cablesconnecting coaxial cables, 2-14connecting Ethernet cables, 2-9

network cables, connecting, 2-8Network port LED display, 2-26null-modem cable, 2-17

O

operating temperature warning, C-3options for rack-mounting, 2-4options for site installation, 2-3output frequency step size, A-4

P

physical specifications, A-1pinouts

Console port connector, B-1Ethernet port connectors, B-3Gigabit Ethernet port connector, B-4Redundant port connector, B-6T1/E1 BITS connector, B-5

power source connection, 2-20Power Status LED, 2-29preinstallation

526359-001-00 Rev B Index-3

Release 1.1 Index

rack-mounting, 2-4preparing for redundant operation, 2-10procedure for rack-mounting, 2-4product disposal warning, C-4

Q

quallified personnel warning, C-2

R

R/W LED, 2-23rack mounting

procedures, 2-4securing in rack, 2-6

rack-mounting, 2-4attaching mounting brackets, 2-4mounting and securing in equipment rack, 2-6options, 2-4preinstallation, 2-4

rack-mounting warning, C-2rear panel LEDs

Ethernet ports, 2-26Power Status LED, 2-29

rebooting, 2-30redundancy support, A-2redundant cabling, 2-10redundant Ethernet cable

connecting, 2-10Redundant port connector

pinouts, B-6removing the Compact Flash memory card, 2-18replacing the Compact Flash memory card, 2-18required equipment, 2-2required tools, 2-2reset button, 2-30RF specifications

output frequency step size, A-4upstream modulation, A-4upstream per-channel bit rate, A-4

RF spectrum

downstream modulation, A-4downstream output frequency range, A-4

RF spectrum specificationsupstream input frequency range, A-4

RJ-45 Ethernet connector, 2-2, 2-9RJ-45 Ethernet connectors, B-3, B-6RS-232, 2-2RS-232 crossover cable, 2-17

S

safety warnings, C-1securing in an equipment rack, 2-6SELV circuit warning, C-2setting up a console monitor, 2-16setting up for desktop operation, 2-7SFP modules, 2-11Small Form-factor Plug-in modules, 2-11specifications, A-1stacking warning, C-2System LED displays, 2-23

T

T1/E1 BITS connectorpinouts, B-5

T1/E1 BITS interfaceconnecting a cable to, 2-13

T1/E1 BITS LEDrear panel LEDs

T1/E1 BITS LED, 2-28temperature

nonoperating, A-2operating, A-2

toolsrequired to install, 2-2

U

upstream channelsconnecting to, 2-14

upstream input frequency range, A-4

Index-4 526359-001-00 Rev B


upstream modulation, A-4upstream per-channel bit rate, A-4Upstream port LEDs, 2-24

W

warningelectrical grounding, C-3electrical safety, C-3grounded equipment, C-3installation, C-2jewelry removal, C-4LED product, C-3lightning activity, C-4operating temerature, C-3product disposal, C-4qualified personnel, C-2rack-mounting, C-2SELV circuit, C-2stacking, C-2

wireless portconnecting a cable to, 2-15

526359-001-00 Rev B2/11

Visit our website at:www.motorola.com

bsr 2000 - release 1.1 - hardware installation guide

Documents