buidling&construction _fianl reort _sep2011

======================================================================

Environmental Guidance Manual Sector: Building & Construction Projects

======================================================================

Rajasthan State Pollution Control Board ii Environmental Guidance Manual – Building & Construction Projects

Contents Chapter No. Title Page No.

Acknowledgements iv Project Team v List of Annexures vi

About the Manual vii

Chapter 1 Introduction 1.0 About RSPCB 1 1.1 Building and Construction –Categorization by RPCB 2 1.2 Building and Construction- Classification by MoEF for EC Applicability 3

Chapter 2 Important Definitions 2.0 Important Definitions of the Environmental Acts 5 2.1 National Building Code of India 2005 9 2.2 Energy Conservation Building Code – User Guide, 2009 10

Chapter 3 Environmental Acts and Legal Requirements 3.0 Legal Requirements - Water Act 14 3.1 Legal Requirements - Air Act 15 3.2 Legal Requirements - E (P) Act 16 3.3 Requirements for Ground Water Extraction 16 3.4 Legal Requirements - Hazardous Waste Rules 16 3.5 Restrictions - Aravalli Range 17 3.6 Restrictions - Mount Abu Eco-Sensitive Zone 18 3.7 Notification for Integrated Township dated 29.03.2007 20

Chapter 4 Statutory Clearance Process 4.0 Environmental Clearance Process 25 4.1 Consent Management System – RPCB 27

Chapter 5 Environmental Aspects and Guidance 5.0 Environmental Aspects 33 5.1 Environmental Norms 33 5.2 Guidelines for Project Developer 34

Rajasthan State Pollution Control Board iii Environmental Guidance Manual – Building & Construction

Chapter 6 Good Practices 6.0 Water Conservation & Augmentation 35 6.1 Parking Spaces 35 6.2 Dual Plumbing Systems and Grey Water Treatment 35 6.3 Locations of the Septic Tanks 35 6.4 Energy Labeling Programme 36 6.5 Energy Conservation Building Code 36 6.6 ECBC User Guide, 2009 37 6.7 BEE Star Rating for Office Buildings 37 6.8 Cool Roof’s 38 6.9 Good Practices in Design & Construction 38

Chapter 7 Checklist 7.0 Checklist for CTE 40 Annexures 43-93

Rajasthan State Pollution Control Board iv Environmental Guidance Manual – Building & Construction Projects

Acknowledgements At the instance of Rajasthan State Pollution Control Board, the Administrative Staff College of India undertook the preparation of Environmental Guidance Manual for Building & Construction Projects. The initiative of RSPCB in the preparation of sector specific guidance manual is in line with National Environmental Policy 2006, which recommends code of practices for different category of industries. ASCI would like to thank the constant support extended by Dr. V.S. Singh, Chairperson and Dr. Deep Narayan Pandey, Member Secretary of RSPCB. ASCI would like to thank Shri Anand Lal Mathur, Chief Environmental Engineer for coordinating the project and for providing the guidance whenever needed. ASCI also thank the Core Group and Shri. T. S. Ranawat, Sr.E.E for their valuable feedback.

Rajasthan State Pollution Control Board v Environmental Guidance Manual – Building & Construction

Project Team

Project Coordination Rajasthan State Pollution Control Board

Dr. Deep Narayan Pandey Member Secretary Mr. Anand Lal Mathur Chief Environmental Engineer

Core Group - RSPCB Mr. A.K.Puri, Sr.E.E

Mr. V.K. Singhal, Sr.E.E

Mr. R.K.Gaur, C.S.O

Mr. Pradeep Agarwal, In charge Mines,

Mr. Manoj Agarwal, L.O

Mr. Mahesh Rastogi, E.E

Sector Group Head - RSPCB Mr. T. S. Ranawat, Sr.E.E

Project Team ASCI

Prof. V.S. Chary Dean of Research and Management Studies Mr. G. Bala Subramanyam Advisor, Environment Area Project Leader

Rajasthan State Pollution Control Board vi Environmental Guidance Manual – Building & Construction Projects

Annexure

Annexure No. Title Page No. Annexure No.1 Form 1 44 Annexure No.2 Form 1A 53 Annexure No.3 Proforma of Affidavit For CTE/CTO 59 Annexure No.4 Classification of Projects For Consent Fee Purpose 60 Annexure No.5 Consent To Establish fee - Water Act 61 Annexure No.6 Consent To Establish fee - Air Act 62 Annexure No.7 Areas As Identified By CGWA 63 Annexure No.8 General Standards For Discharge of Effluents 67 Annexure No. 9 National Ambient Air Quality Standards 69 Annexure No.10 Noise Ambient Air Quality Standards 71 Annexure No.11 Noise Limits For Generator Sets Run With Diesel 72 Annexure No.12 Estimation of Water Demand 74 Annexure No.13 Area Requirements For Parking in Dif. Types of Cities 75 Annexure No.14 Bis Code Of Practices 76 Annexure No.15 Rain Water Harvesting Structures 77 Annexure No. 16 Availability of Rainwater Through Roof Top Rain Water Harvesting 81 Annexure No. 17 Certain Design Factors – ECBC User Guide 2009 82 Annexure No.18 Energy Saving Potential of Multiple Glazed Windows

Over Single Window (24 Hours Usage) 84 Annexure No.19 Suggestions Application For Consent To Establish 85 Annexure No.20 Consent Fee Structure With Reference To 91 Submission Time of CTO Application Annexure No.21 Consent To Operate Fee - Water Act 92 Annexure No.19 Consent To Operate Fee – Air Act 93

Rajasthan State Pollution Control Board vii Environmental Guidance Manual – Building & Construction

About The Manual The objective of developing sector specific guidance manual for Building & Construction Projects is to provide clear and concise information to all the stakeholders i.e. project proponent, environmental consultant, Rajasthan State Pollution Control Board officials and the public to have a better understanding on the relevant environmental aspects in the initial stage itself. This manual covers the legal requirements, clearance process, environmental standards and maintenance of statutory records. The manual will also cover the environmental aspects due to Building & Construction projects. The project proponent may use this manual to ensure that all the aspects of the environment due to the project are addressed and adequate mitigation measures are planned in the environmental management plan and he will be fully aware of the environmental process and requirements. The consultants will have similar understanding of the sector and the procedures involved, so that the quality of EMP reports will be improved. The reviewers across the board may have same understanding about the sector and helps them in the process of review and appraisal. Public who are concerned about Building & Construction projects, will have information about the environmental aspects, standards, regulatory requirements etc., and have a better understanding about the Building & Construction projects. The preparation of sector specific guidance manual by Rajasthan State Pollution Control Board is in line with National Environmental Policy 2006, which emphasizes on:

- Formulate and periodically update, codes of good practices for environment for different category of industries

- Ensure faster decision making with greater transparency and access to information, together with necessary capacity building

The manual is meant to serve as a guidance purpose only. Although every care has been taken to avoid errors or omissions, we will not be responsible for any damage or loss to any person, for the result of any action taken on the basis of this manual. Any discrepancy found may be brought to the notice of the Board. In case of interpretation of any question related to law, the provisions of the original law and the rules made thereunder with various government directions/resolutions will have to be read and followed. In case of amendment to the original Act/Rules/Notifications made thereunder, the provisions as amended from time to time shall be applicable.

Introduction

1.0 About RSPCB The Rajasthan State Pollution Control Board (RSPCB) is a statutory authority entrusted to implement environmental laws & rules within the jurisdiction of the State of Rajasthan. The Board ensures proper implementation of the statues, judicial and legislative pronouncements related to environmental protection within the state. The Board was established in the year 1975 under the provisions of Water (Prevention & Control of Pollution) Act 1974. Over the years, RSPCB was entrusted with various responsibilities under different enactments made. Currently RSPCB is responsible, completely or partially for the implementation of following Acts and Rules: • The Water (Prevention & Control of Pollution) Act, 1974 and Rules made there off • The Air (Prevention & Control of Pollution) Act, 1981 and Rules made there off • The Water (Prevention & Control of Pollution) Cess Act 1977 and Rules made there off • The Public Liability Insurance Act, 1991 and Rules made there off • The Environmental Protection Act, 1986 and Rules made there off

‐ Hazardous Wastes (Management, Handling & Transboundary Movement) Rules 2008 as amended

‐ Manufacture, Storage and Import of Hazardous Chemical Rules, 1989 as amended ‐ Municipal Solid Waste (Management and Handling) Rules, 2000 ‐ Bio Medical Waste (Management and Handling) Rules, 1998 as amended ‐ Ozone Depleting Substances (Regulation) Rules, 2000 ‐ The Batteries (Management and Handling) Rules, 2001 ‐ Fly Ash Notification as amended S.0. 2804(E) dated 3rd November 2009 ‐ Environmental Impact Assessment Notification, 2006 as amended ‐ The Chemical Accidents (Emergency Planning, Preparedness and Response) Rules,

1996 ‐ The Recycled Plastic Waste (Management and Handling) Rules, 2011 ‐ The Manufacture, Use, Import, Export and Storage of Hazardous Micro Organisms,

Genetically Engineered Organism or Cells Rules, 1989 ‐ Notification No. S.O. 319 (E) dated 7th May 1992 (Restricting certain activities in

special specified area of Aravalli Range) ‐ Notification No. S.O. 1545 (E) dated 25th June 2009 declaring Mount Abu Eco

Sensitive Zone ‐ The Noise Pollution (Regulation and Control) Rules, 2000 as amended ‐ E-waste (Management & Handling) Rules, 2011

CHAPTER 1

Rajasthan State Pollution Control Board 2 Environmental Guidance Manual – Building & Construction Projects

1.1 Building & Construction Projects – Categorization by RSPCB

Reference

Project Description

Red category RSPCB office order dated 21.12.2010

S. No. 39 Building/Construction projects having built up area equal to or more than 2,500 sq.m S.No.72 Health Care establishments, nursing homes and hospitals

Orange category RSPCB office order dated 21.12.2010

S. No. 1 Hotel, motel, guest house, lodging > 25 beds S.No.2 Restaurant ≥ 25 seats S.No 23 Establishment / activities having D.G Set (more than 100 KVA) S.No 27 Marriage gardens, community centers and clubs with kitchen facilities S.No 28 Institutions for training, education and capacity building S.No 29 Computer Software development and business promotion centres employing more than 50 persons

Green category RSPCB office order dated 21.12.2010

All those projects, which are not covered under Red or Orange category and are discharging waste water and or air emissions will be covered under green category

Appendix A Category G.S.R 73 dated 10.12.2010, Department of Environment, Govt. of Rajasthan

S.No 37. Building and Construction Project ≥ 20000 Sq.M built up area S.No 38. Township and Area Development project ≥ 50 ha or dwelling unit ≥ 100 S.No 83. Hotels, Motels, Resorts i) > 100 beds if located in the town having Divisional Head Quarter or > 200 beds if located else where, or /and ii) Covered under EIA Notification 2006 /Aravali Notification 1992 or/and

Rajasthan State Pollution Control Board 3 Environmental Guidance Manual – Building & Construction

iii) Located in water body /within 200mts of HFL of water body

Appendix B Category G.S.R 73 dated 10.12.2010, Department of Environment, Govt. of Rajasthan

S.No 1. Hotels, Motels, Resorts (Lodging and Boarding) having ≤ 200 beds but ≥ 25 beds other than following: i) Having > 100 beds if located in the town having Divisional Head Quarter, or /and ii) Covered under EIA Notification 2006 /Aravali Notification 1992 or/and iii) Located in water body /within 200mts of HFL of water body S.No 2.Restaurant ≥ 25 seats S.No 22. Building and Construction projects ≥ 2500 Sq.M but < 20,000 sq.m built up area S.No 23. Township and Area development project ≥ 5ha but < 50 ha and or dwelling units ≥ 50 but <100 units S.No 64. Establishments/ activities having D.G set (More than 100 KVA) S.No 68. Marriage garden, community center and club with kitchen facilities

1.2 Building & Construction Projects – Classification by MoEF for EC applicability Environmental Impact Assessment Notification S.O.1533 (E) of 14th September 2006 as amended in 2009 has made it mandatory to obtain prior environmental clearance for scheduled development projects. As per these notifications, Building & Construction projects are classified as category B projects.


Project or activity Category with threshold Conditions Category A Category B

8 (a) Building and Construction projects

--- ≥20, 000 sq. meters and < 1,50,000 sq. meters of built-up area#

# The built up area for the purpose of this Notification is defined as “the built up or covered area on all the floors put together including basement(s) and other service areas, which are proposed in the building /construction projects”

7(c) Industrial estates/parks/complexes/areas, export processing zones (EPZs), special economic zones (SEZs), Biotech parks, Leather complexes

1. If at least one industry in the proposed industrial estate falls under the Category A, entire industrial area shall be treated as Category A, irrespective of the area 2. Industrial estates with area greater than 500ha. and housing at least one Category B industry

1. Industrial estates housing at least one Category B industry and area <500ha 2. Industrial estates of area >500ha. and not housing any industry belonging to Category A or B

Special conditions shall apply Note: - Industrial estate of area below 500ha. and not housing any industry of Category ‘A’ or ‘B’ does not require clearance - If the area is less than 500ha. but contains building and construction projects >20,000 sq. mt and or development area more than 50ha it will be treated as activity listed at serial no. 8(a) or 8(b) in the Schedule, as the case may be

Reference: EIA Notification S.O 1533 dated 14th September 2006 and amended Notification S.O 3067 (E) dated 1st December 2009 / S.O.695 (E) dated 4th April 2011, MoEF, GoI

Important Definitions

2.0 Important Definitions of the Environmental Acts

The Water (Prevention & Control of Pollution) Act, 1974

Section Key word Definition

Section 2 (d) Occupier In relation to any factory or premises, means the person who has control over the affairs of the factory or the premises, and includes, in relation to any substance, the person in possession of the substance

Section 2 (dd) Outlet Any conduit pipe or channel, open or closed, carrying sewage or trade effluent or any other holding arrangement which causes or is likely to cause pollution

Section 2 (e) Pollution Contamination of water or such alteration of the physical, chemical or biological properties of water or such discharge of any sewage or trade effluent or of any other liquid, gaseous or solid substance into water (whether directly or indirectly) as may, or is likely to, create a nuisance or render such water harmful or injurious to public health or safety, or to domestic, commercial, industrial, agricultural or other legitimate uses, or to the life and health of animals or plants or of aquatic organisms

Section 2 (g) Sewage effluent Effluent from any sewerage system or sewage disposal works and includes sullage from open drains

Section 2 (gg) Sewer Any conduit pipe or channel, open or closed, carrying sewage or trade effluent

Section 2 (j) Stream Includes river, water course (whether flowing or for the time being dry), inland water (whether natural or artificial), sub-terrain waters, sea or tidal waters to such extent or, as the case may be, to such point as the state government may, by notification in the official gazette specify in this behalf

Section 2 (k) Trade effluent Includes any liquid, gaseous or solid substance, which is discharged from any premises used for carrying on any industry, operation or process, or treatment and disposal system, other than domestic sewage

Section 47 (2) (a) Company Anybody corporate, and includes a firm or other association of individuals

Section 47 (2) (b) Director In relation to a firm means a partner in the firm

The Air (Prevention & Control of Pollution) Act, 1981 Section 2 (a) Air pollutant Any solid, liquid or gaseous substance (including

CHAPTER 2


noise) present in the atmosphere in such concentration as may be or tend to be injurious to human beings or other living creatures or plants or property or environment

Section 2 (b) Air pollution The presence in the atmosphere of any air pollutant Section 2 ® Approved appliances Any equipment or gadget used for the bringing of

any combustible material or for generating or consuming any fume, gas of any particulate matter and approved by the State Board

Section 2 (d) Approved fuel Any fuel approved by the State Board for the purpose of the Act

Section 2 (h) Chimney Includes any structure with an opening or outlet from or through which any air pollutant may be emitted

Section 2 (i) Control equipment Any apparatus, device, equipment or system to control the quality and manner of emission of any air pollutant and includes any device used for securing the efficient operation of any industrial plant

Section 2 (k) Industrial plant Any plant used for any industrial or trade purposes and emitting any air pollutant into the atmosphere

Section 2 (j) Emission Any solid or liquid or gaseous substance coming out of any chimney, duct or flue or any other outlet

Section 2 (m) Occupier The person who has control over the affairs of the factory or the premises, and includes, in relation to any substance, the person in possession of the substance



The Water (Prevention & Control of Pollution) Cess Act, 1977

Section 2 (a) Local Authority Municipal corporation or a municipal council (by whatever name called) or a cantonment board or any other body, entrusted with the duty of supplying the water under the law by or under which it is constituted

Section 2 ® Industry Any operation or process, or treatment and disposal system, which consumes water or gives rise to sewage effluent or trade effluent, but does not include any hydel power unit



The Environmental Protection Act 1986

Section 2 (a) Environment Includes water, air, land and the inter-relationship,


which exists among and between water, air and land, and human beings, other living creatures, plants, micro-organism and property

Section 2 (b) Environmental pollutant

Any solid, liquid or gaseous substance present in such concentrations as may be, or tend to be, injurious to environment

Section 2 ® Environmental pollution

Presence in the environment of any environmental pollutant

Section 2 (d) Handling Manufacture, processing, treatment, package, storage, transportation, use, collection, destruction, conversion, offering for sale, transfer or the like of such substance

Section 2 (e) Hazardous substance Any substance or preparation which by reason of its chemical or physico-chemical properties or handling, is liable to cause harm to human beings, other living creatures, plant, micro-organism, property or the environment

Section 2 (f) Occupier A person who has control over the affairs of the factory or the premises and includes in relation to any substance, the person in possession of the substance

The Manufacture, Storage and Import of Hazardous Chemicals Rules, 1989

Rule 2 (e) Hazardous chemical • Any chemical which satisfies any of the criteria

laid down in Part I of Schedule 1 or listed in Column 2 of Part II of this Schedule

• Any chemical listed in Column 2 of Schedule 2 • Any chemical listed in Column 2 of Schedule 3

Rule 2 (h) Industrial activity • An operation or process carried out in an industrial installation referred to in Schedule 4 involving or likely to involve one or more hazardous chemicals and includes on-site storage or on-site transport which is associated with that operation or process, as the case may be; or

• Isolated storage; or • Pipeline

Rule 2 (i) Isolated storage Means storage of a hazardous chemical, other than

storage associated with an installation on the same site specified in Schedule 4 where that storage involves atleast the quantities of that chemical set out in Schedule 2

Rule 2 (j) Major accident Means an incident involving loss of life inside or outside the installation, or ten or more injuries inside and/or one or more injuries outside or


release of toxic chemicals or explosion or fire or spillage of hazardous chemicals resulting in on-site or off-site emergencies or damage to equipment leading to stoppage of process or adverse affects to the environment

Rule 2 (m) Site Means any location where hazardous chemicals are manufactured or processed, stored, handled, used, disposed of and includes the whole of an area under the control of an occupier and includes pier, jetty or similar structure whether floating or not

Rule 2 (n) Threshold quantity • In the case of a hazardous chemical specified in Column 2 of Schedule 2, the quantity of that chemical specified in the corresponding entry in Columns 3 and 4

• In the case of a hazardous chemical specified in Column 2 of Part I of Schedule 3, the quantity of that chemical specified in the corresponding entry in Columns 3 & 4 of that part

• In the case of substances of a class specified in Column 2 of Part II of Schedule 3, the total quantity of all substances of that class specified in the corresponding entry in Columns 3 and 4 of that part

The Hazardous Waste (Management, Handling & Transboundary Movement) Rules, 2008

Rule 3 (l) Hazardous waste Any waste which by reason of any of its physical, chemical, reactive, toxic, flammable, explosive or corrosive characteristics causes danger or is likely to cause danger to health or environment, whether alone or when in contact with other wastes or substances, and shall include • Waste specified under column (3) of Schedule-I • Wastes having constituents specified in

Schedule-II if their concentration is equal to or more than the limit indicated in the said Schedule, and

• Wastes specified in Part A or Part B of the Schedule-III in respect of import or export of such wastes in accordance with rules 12,13 and 14 or the wastes other than those specified in Part A or Part B if they possess any of the hazardous characteristics specified in Part C of that Schedule


The Batteries (Management & Handling) Rules, 2001

Rule 3 (e) Battery Lead acid battery which is a source of electrical

energy and used as lead metal Rule 3 (h) Consumer Person using lead batteries excluding bulk

consumer Rule 3 ® Used batteries Used, damaged and old lead acid batteries or

components thereof

E- Waste (Management & Handling) Rules 2011

Rule 3 © Bulk Consumer Bulk users of electrical and electronic equipment such as Central Government or State Government Departments, Public Sector undertaking banks, educational institutions, multinational organizations international agencies and private companies that are registered under the Factories Act 1948 and Companies Act, 1956

Rule 3 (e) Collection centers A center established individually or jointly or a registered society or designated agency or a company or an association to collect e- waste

Rule 3 (f) Consumer Any person using electrical and electronic equipment excluding the bulk consumers

Rule 3 (h) Disposal Any operation which does not lead to recycling, recovery or reuse and includes physic- chemical or biological treatment, incarnation and deposition in secured landfill

Rule 3 (i) Environmentally sound management of E-waste

Taking all steps required to ensure that e-waste are managed in a manner which shall protect health and environment against any adverse effects which may result from hazardous substance contained in such wastes

Rule 3 (j) Electrical and electronic equipment

Equipment which is dependent on electrical currents or electromagnetic fields to be fully functional

Rule 3 (k) E -waste Waste electrical and electronic equipment, whole or in part or rejects from their manufacturing and repair process, which are intended to be discarded

Rule 3 (l) Extended producer responsibility

Responsibility of any producer of electrical or electronic equipment for their products beyond manufacturing until environmentally sound management of their end-of-life products

Rule 3 (p) Orphaned products Non branded or assembled electrical and electronic equipment as specified in Schedule I or those produced by a company which has closed its operation s or has stopped products support

Rule 3 (q) Producer Any person who irrespective of selling technique used


i. Manufactures and offers to sell electrical and electronic under his own brand

ii. Offers to sell under his own brand, assembled electrical and electronic equipment produced by other manufactures or suppliers

iii. Offers to sell imported electrical and electronic equipment

Rule 3 ® Recycler Any person who is engaged in recycling or reprocessing of used electrical and electronic equipment or assemblies or their components

Rule 3 (v) Transporter A person engaged in off-site transportation of e-waste by air, rail, road or water

2.1 National Building Code of India 2005

Key plan A key plan drawn to a scale of not less than 1 in 10,000 shall be submitted along with the application for a development/building permit showing the boundary locations of the site with respect to neighborhood landmarks. The minimum dimension of the key plan shall be not less than 75mm.

Site plan The site plan shall be drawn to a scale of not less than 1 in 500 for a site up to one hectare and not less than 1 in 1000 for a site more than one hectare and shall show: a. The boundaries of the site and any contiguous land belonging to the owner

thereof b. The position of the site in relation to neighboring street c. The name of the streets in which the building is proposed to be situated, if any d. All existing buildings standing on, over or under the site including service lines e. The position of the building and of all other buildings (if any) which the

applicant intends to erect upon his contiguous land referred to in (a) in relation to:

i. The boundaries of the site and in case where the site has been partitioned, the boundaries of the portion owned by the applicant and also of the portions owned by others

ii. All adjacent street, buildings (with number of storeys and height) and premises within a distance of 12m of the site and of the contiguous land (if any) referred to in (a); and

iii. If there is no street within a distance of 12m of the site, the nearest existing street

f. The means of access from the street to the building, and to all other building (if any) which the applicant intends to erect upon his contiguous land referred to in (a)

g. Space to be left about the building to secure a free circulation of air, admission of light and access for scavenging purposes

h. The width of the street (if any) in front and of the street (if any) at the side or near the buildings

i. The direction of north point relative to the plan of the buildings j. Any physical features, such as wells, drains etc and k. Such other particulars as may be prescribed by the Authority

Access A clear approach to a block or a building


Covered area

Ground area covered by the building immediately above the plinth level. The area covered by the following in the open spaces is excluded from covered area a. Garden, rockery, well and well structures, plant nursery, water pool, swimming

pool (if uncovered), platform round a tree, tank, fountain, bench, CHABUTRA with open top and unenclosed on sides by walls and the like

b. Drainage culvert, conduit, catch-pit, gully-pit, chamber, gutter and the like c. Compound wall, gate, unstoreyed porch and portico, canopy, slide, swing,

uncovered staircase, ramps areas covered by CHHAJJA and the like; and d. Watchmen’s booth, pump house, garbage shaft, electric cabin or sub-stations,

and such other utility structures meant for the services of the building under consideration

Note: For the purpose of this part, covered area equals the plot are minus the area due for open spaces

Floor Area Ratio (FAR)

The quotient obtained by dividing the total covered area (plinth area) on all floors by the area of the plot Total covered area of the floors FAR = Plot area

Plinth area The built up covered area surface of the surrounding ground and surface of the floor, immediately above the ground

Set-Back Line

A line usually parallel to the plot boundaries and laid down in each case by the Authority, beyond which noting can be constructed towards the plot boundaries

Width of means of access (for other buildings)

For all industrial buildings, theatres, cinema houses, assembly halls, stadia, educational buildings, markets, other buildings which attract large crowd, the means of access shall not be less than the following

Width of means of Access (m) Length of Means of Access (m) 12.0 200 15.0 400 18.0 600 24.0 Above 600

Further, in no case shall the means of access be lesser in width than the internal access ways in layouts and subdivision

One pipe system

The system of plumbing in which the wastes from the sinks, baths and washbasins, and the soil pipe branches are all collected into one main pipe, which is connected, directly to the drainage system. Gully traps and waste pipes are completely dispersed with, but all the traps of the water closets, basins etc are completely ventilated to preserve the water seal

Two pipe system

The system of plumbing in which soil and waste pipes are distinct and separate. The soil pipes being connected to the drain direct and waste pipes through a trapped gully. All traps of all appliances are completely ventilated in this system


2.2 Energy Conservation Building Code – User Guide, 2009

Ballast A device used in conjunction with an electric-discharge lamp to cause the lamp to start and operate under proper circuit conations of voltage, current, waveform, electrode heat etc.

Coefficient of Performance (COP) – cooling

The ratio of the rate of the heat removal to the rate of energy input, in consistent units, for a complete refrigerating system or some specific portion of that system under designated operating conditions

Coefficient of Performance (COP) – heating

The ration of the rate of heat delivered to the rate of energy input, in consistent units, for a complete heat pump system, including the compressor and, if applicable, auxiliary heat, under designated operating conditions

Commercial building

All buildings except for multi-family buildings of three stories or fewer above grade and single-family buildings

Cool roof A property of a surface that describes its ability to reflect and reject heat. Cool roof surfaces have both a light color (high solar reflectance) and a emittance (can reject heat back to the environment)

Day lighted area The daylight illuminated floor area under horizontal fenestration (skylight) or adjacent to vertical fenestration (window)

Effective Aperture Visible Light Transmittance x Window-to-Wall Ratio (EA= VLT x WWR) Horizontal Fenestration

The area under a skylight, monitor, or sawtooth configuration with an effective aperture greater than 0.001 (0.1%). The daylighted area is calculated as the horizontal dimension in each direction equal to the top aperture dimension in that direction plus either the floor-to-ceiling height (H) for skylights, or 1.5H for monitors, or H or 2H for the sawtooth configuration, or the distance to the nearest 1000mm (42in) or higher opaque partition, or one-half the distance to an adjacent skylight or vertical glazing, whichever is least

Vertical Fenestration

The floor area adjacent to side apertures (vertical fenestration in walls) with an effective aperture greater than 0.06 (6%). The daylighted area extends into the separate perpendicular to the side aperture a distance either two times the head height of the side aperture or to the nearest 1.35m (54 in) or higher opaque partition, whichever is less. In the direction parallel to the window, the daylighted area extends a horizontal dimension equal to the width of the window plus either 1m (3.3 ft) on each side of the aperture, the distance to an opaque partition, or one-half the distance to an adjacent skylight or window, whichever is least.

Enclosed building A building that is totally enclosed by walls, floors, roofs and openable devices such as doors and operable windows

Energy Efficiency Ratio (EER)

Performance of smaller chillers and rooftop units is frequently measured in EER rather than 1/η (kW/ton). It is the ratio of net cooling capacity in Btu/h to total rate of electric input in watts under designated operating conditions. The higher the EER, the more efficient the unit

Façade area Area of the facade, including overhanging soffits, cornices, and protruding columns, measured in elevation in a vertical plane, parallel to the plane of the face of the building. Non-horizontal roof surfaces shall be included in the calculations of vertical façade area by measuring the area in a plane parallel to the surface

Fenestration All areas (including the frames) in the building envelope that let in light, including windows, plastic panels, clerestories, skylights, glass doors that are more than one-half glass, and glass block walls


Skylight A fenestration surface having a slope of less than 60 degrees from the horizontal plane. Other fenestration, even if mounted on the roof of a building, is considered vertical fenestration

Fenestration area Total area of the fenestration measured using the rough opening and including the glazing, sash, and frame. For doors where the glazed vision area is less than 50% of the door area, the fenestration area is the glazed vision area. For all other doors, the fenestration area is the door area

HVAC system The equipment, distribution systems, and terminals that provide, either collectively or individually, the processes of heating, ventilating, or air conditioned to a building or portion of a building

Lighting Efficacy (LE)

The quotient of the total lumens emitted from a lamp or lamp/ballast combination divided by the watts of input power, expressed in lumens per watt

Lighting Power Density (LPD)

The maximum lighting power per unit of area of a building classification of space function

Lumen It is the unit of a total light output from a light source. If a lamp or fixture were surrounded by a transparent bubble, the total light flow through the bubble is measured in lumens. Lamps are rated in lumens, which is the total amount of light they emit, not their brightness and not the light level on a surface. Typical indoor lamps have light output ranging from 50 to 10,000 lumens. Lumen value is used for purchasing and comparing lamps and their outputs. Lumen output of a lamp is not related to the light distribution pattern of a lamp

Luminaries A complete lighting unit consisting of a lamp or lamps together with the housing designed to distribute the light, position and protect the lamps, and connect the lamps to the power supply

R-Value (thermal resistance)

The reciprocal of the time rate of heat flow through a unit area induced by a unit temperature difference between two defined surfaces of material or construction under steady-state conditions. Units of R are m2 .K/W (h.ft2.0F/Btu). For the perspective building envelope option, R-value is for the insulation alone and does not include building materials or air films

Reflectance The ration of the light reflected by a surface to the light incident upon it Shading coefficient (SC)

The ratio of solar heat gain at normal incidence through glazing to that occurring through 3mm (1/8 in) thick clear, double-strength glass. Shading coefficient, as used herein, does not include interior, exterior, or integral shading devices

Skylight roof ratio (SRR)

The ratio of the total skylight area of the roof, measured to the outside of the frame, to the gross exterior roof

Solar Heat Gain Coefficient (SHGC)

The ratio of the solar heat gain entering the space through the fenestration area to the incident solar radiation, typically ranging from 0.9 to 0.1, where lower values indicate lower solar gain. Solar heat gain includes directly transmitted solar heat and absorbed solar radiation, which is then reradiating, conducted, or converted into the space

Tinted (As applied to fenestration) Bronze, green, or grey coloring that is integral with the glazing material. Tinting does not include surface applied films such as reflective coatings, applied either in the field or during the manufacturing process

U-factor (Thermal Heat transmission in unit time through unit area of a material or


Transmittance) construction and the boundary air films, induced by unit temperature difference between the environments on each side. Units of U are W/m2-0C (Btu/h ft2 0F).

Window Wall Ratio (WWR)

The ratio of vertical fenestration area to gross exterior wall area. Gross exterior wall area is measures horizontally from the exterior surface; it is measured vertically from the top of the floor to the bottom of the roof

Urban Heat Island Effect

An Urban Heat Island is a metropolitan urban area, which is significantly warmer than its surroundings. As population centres grow in size, they tend to have a corresponding increase in average temperature. Scientists refer to this phenomenon as the “Urban Heat Island Effect”. The two main causes of the urban heat island is modification of the land surface by urban development and waste heat generated by energy usage. One consequence of urban heat island is the increased energy required for air conditioning and refrigeration in cities that are in comparatively hot climates

Environmental Acts and Legal requirements 3.0 Legal requirements – Water Act

The Water (Prevention & Control of Pollution) Act, 1974 and as amended

Section 25 (1) Restrictions on new outlets and discharges

Subject to the provisions of this section, no person shall, without the previous consent of the State Board a. Establish or take any steps to establish any industry, operation or process, or any treatment and disposal system or an extension or addition thereto, which is likely to discharge sewage or trade effluent into a stream or well or sewer or on land (such discharge being hereafter in this section referred to as discharge of sewage); or b. Bring into use any new or altered outlets for the discharge of sewage; or c. Begin to make any new discharge of sewage

Section 44 Penalty of contravention of section 25

Whoever contravenes the provision of section 25 shall be punishable with imprisonment for a term which shall not be less than two years but which may extend to six years and with fine

Section 31 (1) Furnishing of information to State Board and other agencies in certain cases

If at any place where any industry, operation or process, or any treatment and disposal system or any extension or addition there to is being carried on due to accident or other unforeseen act or event, any poisonous, noxious or polluting matter is being discharged, or likely to be discharged into the stream or well or sewer or on land and as a result of such discharge, the water in any stream or well is being polluted or is likely to be polluted then the person incharge of such place shall forthwith intimate the occurrence of such accident, act or event to the board and such other authorities or agencies as may be prescribed.

Section 48 Offences by Government Departments

Where an offence under this Act has been committed by any Department of Government, the Head of the Department shall be deemed to be guilty of the offence and shall be liable to be proceeded against and punished accordingly: Provided that nothing contained in this section shall render such Head of the Department liable to any punishment if he proves that the offence was committed without his knowledge or that he exercised all due diligence to prevent the commission of such offence

Section 42(G) Penalty for Certain Acts

For the purpose of obtaining any consent under section 25 or section 26, knowingly or willfully makes a statement which is false in any material particular, shall be punishable with imprisonment for a term which may extend to three months or with fine which may extend to or with both

CHAPTER 3


3.1 Legal Requirements – Air Act

The Air (Prevention & Control of pollution) Act, 1981 and as amended

Section 21 (1) Restrictions on use of certain industrial plants

Subject to the provisions of this section, no person shall, without the previous consent of the State Board, establish or operate any industrial plant in an air pollution control area

Section 37 (1) Penalty of contravention of Section 21

Whoever fails to comply with the provisions of section 21, be punishable with imprisonment for a term which shall not be less than one year and six months but which may extend to six years and with fine

Section 23(1) Furnishing of information to State Board and other agencies in certain cases

Where in any area the emissions of any air pollutants into the atmosphere in excess of the standards laid down by the State board occurs or in apprehended to occur due to accident or other unforeseen act or event, the person incharge of the premises from where which emission occurs or is apprehended to occur shall forthwith intimate the fact of such occurrence or apprehension of such occurrence to the State Board and to such authorities or agencies as may be prescribed

Section 41 Offences by Government Department

1.Where an offence under this Act has been committed by any Department of Government, the Head of the Department shall be deemed to be guilty of the offence and shall be liable to be proceeded against and punished accordingly Provided that nothing contained in this section shall render such Head of the Department liable to any punishment if he proves that the offence was committed without his knowledge or that he exercised all due diligence to prevent the commission of such offence 2.Not withstanding anything contained in sub-section (1), Where an offence under this Act has been committed by any Department of Government and it is proved that the offence has been committed with the consent or connivance of, or is attributable to any neglect on the part of, any officer, other than Head of the Department, such officer shall also be deemed to be guilty of the offence and shall be liable to be proceeded against and punished accordingly

Section 38 (G) Penalties for Certain Acts

For the purpose of obtaining any consent under section 21, makes a statement which is false in any material particular shall be punishable with imprisonment for a term which may extend to three months or with fine which may extend to or with both


3.2 Legal Requirements – E (P) Act

S.O. 1533 dated 14th September 2006 as amended

Projects listed in the schedule shall obtain prior environmental clearance from the concerned regulatory authority.

Section 15 of E (P) Act 1986

Punishable with imprisonment up to 5 years with fine up to one lakh or with both

Section 16 of E (P) Act 1986

When a company has committed offence under E (P) Act, and it is proved that the offence has been committed with the consent or connivance of, or neglect on the part by any director, manager, secretary or other officials shall be deemed to be guilty and shall be liable for punishment.

3.3 Requirements for Ground Water Extraction Keeping in view of the requirements stated in the Policy guidelines for clearance of ground water abstraction for various uses issued by the Central Ground Water Authority, Ministry of Water Resources, GoI vide their letter dated 14.10.2009, the following guidelines regarding the requirement of NOC from CGWA for abstraction of ground water by any infrastructure project (proposed/existing) are being followed:

S. No

Guidelines

1. NOC from CGWA shall not be required for abstraction of ground water in the

following cases: • In case of over-exploited areas abstraction < 25m3/day • In case of critical areas abstraction < 50 m3/day • In case of semi critical areas abstraction < 100 m3/day

2. Industry/infrastructure project (proposed/existing) located in safe category

areas, are required to obtain NOC from CGWA if ground water abstraction exceeds 1000 m3/day for hard rock areas and 2000 m3/day for alluvial areas

3. A copy of consent letter will be endorsed to Regional Director, Central Ground Water Board (WR), 6A, Jhalana Institutional Area, Jaipur for their information and necessary action by RSPCB

Please refer RPCB Circular dated 08.01.2010 for further information 3.4 Legal Requirements - Hazardous Waste Rules

Schedule I: Processes generating hazardous waste (S.No 5) Industrial operations using mineral/synthetic oil as lubricant in hydraulic systems

5.1 Used/spent oil 5.2 Wastes/residues containing oil


or other applications Rule 5 (1) Grant of authorization for handling hazardous waste

Every person who is engaged in generation, processing, treatment, package, storage, transportation, use, collection, destruction, conversion, offering for sale, transfer or the like of the hazardous waste shall require to obtain an authorization from the SPCB

3.5 Restrictions – Aravalli Range The MoEF, GoI had stipulated restrictions on certain activities in specified area of Aravalli Range vide Notification No. S.O. 319 (E) dated 7th May 1992 and as amended. As per the Notification the Central Government prohibits the carrying on the following processes and operations, except with its prior permission, in the specified area. Processes and activities which require prior permission

• Location of new industry including expansion/modernization • A. All new mining operations including renewals of mining lease

B. Existing mining leases in sanctuaries/national park and areas covered under Project Tiger and/or C. Mining is being done without permission of the competent authority

• Cutting of trees • Construction of any clusters of dwelling units, farms houses, sheds,

community centres, information centres and any other activity connected with such construction (including roads a part of any infrastructure relating thereto)

• Electrification (laying of new transmission lines) Areas covered under the Notification

• All reserved forests, protected forests or any other area shown as “forest in the land records maintained by the State Government as on the date of this notification in relation to Gurgaon District of the State of Haryana and the Alwar District of the State of Rajasthan

• All areas shown as a. Gair Mumkin Pahar, or b. Gair Mumkin Rada, or c. Gair Mumkin Behed, or d. Banjad Beed, or e. Rundh

In the land records maintained by the State Government as on the date of this notification in relation to Gurgaon district of the State of Haryana and the Alwar district of the State of Rajasthan • All areas covered by notifications issued under Section 4 and 5 of the

Punjab Land Preservation Act, 1900, as applicable to the State of Haryana in the district of Gurgaon up to the date of this notification

• All areas of Sariska National Park and Sariska Sanctuary notified under the Wildlife (Protection) Act, 1972 (53 of 1972)

Clearance process

Any person desirous of undertaking any of the activities mentioned in the Notification No. 319 (E) dated 7th May 1992 shall submit an application to the Secretary, Department of Environment of the


Government of Haryana/Rajasthan, as the case may be. The applicant shall also furnish environment impact statement and an environment management plan and such other information as may be prescribed by such State Governments. The application after due scrutiny shall be placed before the Expert Committee for its recommendations. Based on the recommendations of the Expert Committee, the Department of Environment in the State Government concerned shall take a final decision and convey the same to the applicant within the three months from the date of receipt of application or when further information has been asked for from the applicant within three moths from the date of receipt of such information

Monitoring mechanism

Monitoring Committee, under the Chairmanship of District Collector concerned (Gurgaon in Haryana and Alwar in Rajasthan) shall inter alia monitor the compliance of the conditions stipulated while according Environmental Clearance by State Government The District collectors of Gurgaon in Haryana and Alwar in Rajasthan shall be authorized by the respective State Governments to take necessary action under section 5 of the said Act in respect of cases where the project proponents fail to implement the conditions

Appeal provision

The MoEF retains appellate power against rejection of any proposal and the National Environmental Appellate Authority constituted under the National Environment Appellate Authority Act, 1997 (22 of 1997) shall continue as an Appellate Authority against approval

Note: Refer the Notification No. S.O.319 (E) dated 7th May 1992 and S.O. 1189 (E) dated 29th November 1999 3.6 Restrictions – Mount Abu Eco Sensitive Zone Mount Abu area has significant ecological importance comprising of tropical dry deciduous forests at lower altitude and evergreen forests at higher altitude and the flora and fauna of the region comprise of several endemic and rare species; besides Mount Abu has natural heritage such as Nakki Lake and man-made heritage like Dilwara temples and other heritage buildings and structures. To conserve and protect the area from ecological and environmental point of view, the MoEF had issued Notification No. S.O. 1545 dated 25th June 2009 regulating certain activities in the eco-sensitive zone Regulated Activities

Pending the preparation of the Zonal Master Plan for Eco-sensitive zone and approval thereof by the Central Government in the MoEF, there shall be no increase in the existing parameters of permissible floor area ratio, permissible ground coverage, maximum number of floors and maximum height and all new constructions shall be allowed only after the proposals are scrutinized and approved by Monitoring Committee and all other development activities including additions, alterations, demolitions, repairs, renovations and restorations of buildings shall require prior approval of the Monitoring Committee provided that these do not involve structural changes and are on the existing authorized plinth areas in the Mount Abu Municipal Limits and there shall be no consequential reduction in Tribal area, Forest area, Green area and Agricultural area


Boundaries of the eco-sensitive zone

a. The said eco-sensitive zone is situated in the southern area of Rajasthan in Sirohi District between 240 33’42’’ and 240 39’ 00’’ North latitude and between 720 41’ 36’’ and 720 48’ 06’’ East longitude and the configuration of land is hilly and rugged with high altitudinal variation ranging from 300 meter to 1727 meter. Gurushikar, the highest peak of the Aravalli, is the highest peak between the Himalayas and the Nilgiris. The boundaries of the said eco-sensitive zone comprise North - Southern boundary of Abu Forest Block No.3 South - Northern Boundary of Abu Forest Block No. 1 East - Western and Southern Boundary of Abu Forest Block No.2 West - Eastern boundary of Abu Forest Block No. 3 b. The Eco-sensitive zone covers the entire area of Notified Urban Area Limit, including Mount Abu Municipal Limits adjoining Forest Block Areas. c. The list of the villages in the eco-sensitive zone – Sanigaon, Machgaon, Goagaon, Delwara, Oriya, Jawal, Achalgarh, Salgaon, Torna, Dudhai, Hetamji, Ama d. All activities in the Forest Block Areas (both within and outside Municipal Areas) shall be governed by the provisions of the Rajasthan Forest Act, 1953 and the Forests (Conservation) Act, 1980 (69 of 1980) and all the activities in the Protected Areas (Sanctuary) shall be governed by the provisions of the Wildlife (Protection) Act, 1972 (53 of 1972)

Trees There shall be no felling of trees whether on Forest, Government, Revenue or Private lands within the Eco-sensitive zone without the prior permission of the State Government in case of forest land and the respective District Collector in case of Government, Revenue and Private land as per the procedure which shall be laid down by the State Government

Tourism The tourism activities shall be as per the Tourism Master Plan to be prepared by the Department of Tourism of the Rajasthan State Government

Water • All future and existing buildings, where possible, in the Municipal Are shall provide roof-top rain water harvesting structures with plinth area and the Institutional and commercial buildings shall not draw water from existing water supply schemes in a manner that adversely affects water supply especially to local villages or settlements

• In Non-Municipal Areas rain water harvesting shall be undertaken through such structures as percolation tanks and storage tanks and only other means. Ground water aquifer recharge structures shall be constructed wherever such structures do not lead to slope instabilities

• The rain water collected through storm water drains shall be used to recharge the ground water or to clean the waste disposal drains and sewers

• The extraction of ground water shall be permitted only for the bona-fide agricultural and domestic consumption of the occupier of the ply and the extraction of ground water for industrial or commercial or residential estates or complexes shall require prior written permission, including of the amount that can be extracted, from the State Ground Water


Department. However, the areas rich in ground water may not be delivered for construction activities

Use of Plastics

No person shall use plastic carry bags within the notified area

Development on and protection of hill slopes

• The zonal Master Plan shall indicate areas o hill slopes where development shall not be permitted

• No development shall be undertaken in areas having a steep slope or areas which fall in fault or hazard zones or areas falling on the spring lines and first order streams or slopes with a high degree of erosion as identified by the State Government on the basis of available scientific evidence

• No development on existing steep hill slopes or slopes with a high degree of erosion shall be permitted

Discharge of sewage and effluents

No untreated sewage or effluent shall be permitted to be discharged into any water body or forests within the eco-sensitive zone and the local authority shall provide proper drainage and treatment system for collection, treatment and disposal of untreated/and treated effluent in accordance with the provisions of the Water (Prevention and Control of Pollution) Act, 1974. Moreover, the treated sewage and treated effluent shall be disposed only at or into a point(s) identified and approved by the local authorities and the Monitoring Committee

Monitoring Committee

Under the provisions of sub-section (3) of Section 3 of the Environment (Protection) Act, 1986 (29 of 1986), the Central Government shall constitute a committee to be called the Monitoring Committee to monitor the compliance of the provisions of this notification In case of activities requiring prior permission on environmental clearance, such activities shall be referred to the State Level Environmental Impact Assessment Authority, which shall be the Competent Authority for grant of such clearances

Note: Refer the Notification for complete details 3.7 Notification for Integrated Township dated 29.03.2007 The Government of Rajasthan had issued certain directions in their order dated 29.03.2007 to promote integrated development in future growth of the urban areas of the Rajasthan and to encourage private sector investment/foreign direct investment (FDI) in real estate sector. These directions were issued under Section 297 of the Rajasthan Municipal Act 1959, Section 90 of the Jaipur Development Authority Act 1982, Section 60 of the Rajasthan Housing Board Act, 1970 and Rule 31 of the Rajasthan Urban Improvement (Disposal of urban lands) Rules 1974.

A. Integrated Township Schemes of Private Developers

1. Minimum area for integrated township shall be 10 hectares in Jaipur, 6 hectares in

Divisional Headquarters and 4 hectares in other Municipal Towns and District Head quarters

9 (a). The following land use distribution shall be ensured at scheme level Residential Up to 50% Plotted apartments (of the scheme area 7.5% land be


reserved for EWS and 0.5% land shall be reserved under “Jan Sathi” scheme/informal sector in the scheme

Commercial Up to 5% Available to developer for disposal Institutional (Educational /Medical etc)

Up to 10% Available to developer for disposal

Facilities (Roads, parks & open spaces)

Not less than 35% (including sector level roads)

To be developed as per approved planning. At least 10% area for parks & open spaces shall be reserved. This entire area under roads, parks & open spaces to be surrendered to local authority after development. The Local authority would ensure reservation of adequate land for games and sports facilities

9 (b). Local authorities would develop sector parks on the lines of sector roads as per zonal plans

10. No road shall be less than 40ft. and all the roads shall provide for standard street lighting and essential street furniture. Road connectivity shall be ensured by the developer

12. Gross residential density shall be prescribed on the basis of level of available external development infrastructure. Configuration of plotted/Group housing shall be developer’s option

14. Separate Building Regulations shall be framed for integrated township projects. Suggested points for inclusion in the Building Regulations are as under. The Local Authority shall prepare/amend Building Regulations accordingly: (i). Group housing projects to be encouraged in which all provisions for a decent communities living would be ensure, such securities arrangements, power/water backing backup shops for daily needs, provisions for service class, space for communities gathering, gyms, health club etc (ii). All public areas to have provisions for physically handicapped (iii). Rain water harvesting provisions will be compulsory in all group housing projects and township schemes (iv). Separate regulations for Group housing/malls to be proposed. The regulations so prepared shall provide for the provisions of parking and open spaces which shall be surrendered in favor of the Local Authority

15. In township schemes “community water harvesting strictures” will be constructed by local authority and all water outlets and drainages will be connected to this structure. This shall be strictly enforced by the local authority

21. An “Eco-cess” at the rate of Rs. 1/- per sq.yd. shall be charged by the local bodies for the lands to be developed under this scheme which shall be utilized for greening the city

22. The design of the township shall aim at water and energy conservation. This would mean i. Proper orientation of building blocks ii. Use of appropriate building material iii. Use of non conventional energy sources, particularly solar energy iv. Recycling of waste water and water harvesting

23. The FAR of the entire gross area of township shall be 1.0. this would encourage proper mix of plotted development and group housing and would also encourage vertical development


B. Township Schemes of Local Authorities

1. The Jaipur Development Authority in case of Jaipur and local authority in consultation

with Town Planning Department of the State for other towns of Rajasthan shall declare a well-defined area in appropriate zone as “Town Planning Scheme”. The master plans would be suitably amended to accommodate such schemes

3. Sector plans shall be prepared indicating the sector road network and sector level uses 6. After deducting area of sector road, commercial strips, developer’s land and FDI

pockets from the project area, the redistribution of the available area shall be done in the following manner

Use Percentage Detailed Break up Residential/Plotted

63% 35% To be made available to khatedar in his own land or in the vicinity 15% To be retained by local authority towards cost of Internal Development 5% To be retained by local authority towards external development / augmentation of infrastructure 7.5% To be developed by local authority for EWS/LIG housing 0.5% Would be reserved for convenient shopping/kiosks/informal sector under “Jan Sathi” scheme

Internal Roads 20% Sectoral facilities 7% Local/level facilities/open spaces/parks

10%

C. General Conditions

3.i. Local authority would issue NOC to the developers as per provisions of Master plan

and land use plan 3.iii. Conversion of land would be allowed according to master plan provisions. Wherever

required, change in land use would be first ensured before conversion is permitted 5. Pollution Control Board norms for townships with respect to provisions of

Environmental Clearance as required under Ministry of Environment and Forests (GoI) Notifications shall be applicable

7. The provisions will also apply in the entire NCR Region of Rajasthan state Appendix - 1

If in case of individual khatedar schemes, the entire internal development will be done by the local authority for which plots of equal value would be handed over by the khatedar developer to the local authority

Appendix - 1

Time limit foe completion of project

Type Time period from date of sanction Land development with Up to 10 ha - 3 years


respect to roads, drains, sewerage, power & water supply etc

25% development by the end of the I year 50% development by the end of the II year 100% development by the end of III Year For more than 10 ha - one additional year for each additional 10 ha

Land development & construction works (minimum of 25% on every earmarked plot)

Up to 10 ha - 4 years 33% development by the end of the II year 66% development by the end of the III year 100% development by the end of IV Year For more than 10 ha - one additional year for each additional 10 ha

Please refer to the Notification dated 29.03.2007 for details

Statutory Clearance Process 4.0 Environmental Clearance Process The Building & Construction Projects with built-up area ≥ 20,000 sq.meters and < 1,50,000 sq. meters of built-up area will fall under category 8(a) i.e. “Building and Construction projects” of EIA Notification 2006 as amended. Similarly, the Industrial Estate projects covering an area ≥ 50 ha and construction project > 20,000 sq.meters, not housing any category A or B industry, will be treated as category 8(a) i.e. Building & Construction Projects. In the case of the projects mentioned at item 8 of the schedule of EIA Notification of 2006 as amended in 2011, considering its unique project cycle, the EAC or SEAC concerned shall appraise projects or activities on the basis of Form –1, Form –1A, conceptual plan and EIA report [required only for projects listed under 8(b)] and make recommendations on the project regarding grant of environmental clearance or otherwise and also stipulate the condition for environmental clearance. MoEF, GoI had issued Environmental Impact Assessment Guidance Manual for “Building, Construction, Townships and area Development Projects – 2010” and the same is available at www.moef.nic.in. Form – I and Form – IA are given at Annexure – 1 & 2 Public Consultation As per Para No 7 (i) (III) (d) of EIA Notification dated 14th September 2006 as amended 1st December 2009, all building or construction projects or area development projects (which do not contain category A projects) are not required to undertake public consultation process. Validity of Environmental Clearance The prior environmental clearance granted is valid for a period of five years. The regulatory authority concerned may extend this validity period by a maximum period of five years. However, in the case of Area development projects and Townships [item 8(b)], the validity period shall be limited only to such activities as may be the responsibility of the applicant as a developer. This validity period may be extended by the regulatory authority concerned by a maximum period of 5 years provided an application is made to the regulatory authority by the applicant within the validity period, together with an updated Form I, and supplementary Form IA, for construction projects or activities. Post Environmental Clearance Monitoring The project proponent shall prominently advertise in the newspapers indicating the project has been accorded environmental clearance and the details of regulatory authority website where it is displayed. To the regulatory authority concerned all such reports shall be public documents. The latest such compliance report shall also be displayed on the website of the concerned regulatory.

CHAPTER 4

http://www.moef.nic.in/�


Transferability of Environmental Clearance A prior Environmental Clearance granted for a specific project or activity to an applicant may be transferred during its validity to another legal person entitled to undertake the project or activity on application by the transferor or the transferee with a written “no objection” by the transferor, to, and by the regulatory authority concerned, on the same terms and conditions under which the prior environmental clearance was initially granted, and for the same validity period. Criteria for EIA consultants The MoEF, GoI had stipulated certain criteria for EIA consultants as per the Ministry’s office memorandum dated 2nd December 2009 and amended from time to time. The same are kept in the public domain of Ministry’s website (www.envfor.nic.in). Accordingly, the EIA consultants shall have accreditation with Quality Control of India (QCI)/National Accreditation Board of Education and Training (NABET). The consultants shall include in the EIA report, copy of the accreditation certificate and that provided by the other organizations/laboratories including their status of approvals etc. The MoEF is not considering the EIA reports prepared by the consultants who are not registered with NABET/QCI. Authorized Signatory All correspondence with the regulatory authority including submission of application for TOR/Environmental Clearance, subsequent clarifications, as may be required from time to time, participation in the EAC Meeting on behalf of the project proponent shall be made by the authorized signatory only. The authorized signatory shall also submit a document in support of his claim of being an authorized signatory for the specific project (EIA amendment Notification dated 1st December 2009). Participation of the project proponent during the EAC meetings As per the office memorandum dated 25th February 2010 of MoEF, the authorized representative of the project proponent shall only attend the EAC meetings. The authorized representative of the project proponent should be a reasonably senior officer / executive duly authorized in writing. In case, a consultant is to be nominated as the authorized representative, it should be through a irrevocable power of attorney executed and formally registered with the Sub-Registrar concerned. A copy of the authorization / registered power of attorney, as the case may be should be submitted to the ministry for record. The authorized representative, so nominated should only participate in the SEAC meetings on behalf of the project proponent. The consultant (s) and other experts may, however, assist the authorized representative during the meeting. In the absence of the authorized representative, the proposal will not be considered by the SEAC. Projects requiring recommendation of the Chief Wildlife Warden If the project is located within 10 km radial distance from the national parks, sanctuaries, biosphere reserves, migratory corridors of wild animals, the project proponent shall submit

http://www.envfor.nic.in/�


the map duly authenticated by Chief Wildlife Warden showing these features vis-à-vis the project location and the recommendations or comments of the Chief Wildlife Warden thereon at the stage of EC (EIA amendment Notification dated 1st December 2009). 4.1 Consent Management System – RSPCB

The consent management process adopted at RPCB is explained below in the form of Q & A to facilitate better understanding for the project proponent as well as other stakeholders. Consent To Establish 01. What are the documents required for submission?

The project proponent shall apply in the prescribed CTE application form along with requisite enclosures. It can be downloaded from RSPCB web also (www.rpcb.nic.in) • Requisite consent to establish fee as prescribed under the

Rajasthan Air (P&CP) Rules, 1983 and / or Rajasthan Water (P&CP) Rules, 1975

• Declaration on Rs 10/- non-judicial stamp paper duly attested by notary public (Annexure 3)

• Project report of including all costs duly attested by Chartered Accountant

• Ownership document for land /lease deed • Land conversion letter, if applicable • Copy of partnership deed/MoU & Article of Association as

the case may be • Environmental Management Plan broadly with capacities,

environmental aspects on land, water, air, noise and solid waste –generation /mitigation measure to comply the norms

• Site plan along with access road, signed by the project proponent

• NOC of CGWA as per applicability • Location plan • Document confirming the authorization of signatory of the

application form and enclosures • Status of Environmental Clearance under EIA Notification

dated 14/09/2006, as amended and Aravali Notification 1992, as per applicability

• The application form and enclosures shall be submitted in triplicate

http://www.rpcb.nic.in/�


02. What is the fee to be submitted?

CTE fee is to be paid along with CTE application as notified by the DoE, Government of Rajasthan under of the Water (P&CP) Act, 1974 as amended and under the Air (P&CP) Act, 1981 as amended vide Notification dated 10th December 2010. Please visit www.rpcb.nic.in for notification. Classification of projects for consent fee purpose is given in Annexure 4 CTE fee structure as applicable is given in Annexure 5 & 6 • Whether the project requires environmental clearance under

the provisions of E (P) Act, 1986? If yes, shall pay an extra amount of Rs 15,000/-, as one time consent fee to establish in addition to the fee mentioned in the schedule under the provisions of Water Act & Air Act All projects/activities generating HW as defined under the HW (MH&TM) Rules 2008 and requiring authorization thereunder, the application for consent shall be accompanied with fee equal to one and half times of the amount of fee prescribed under the schedule, other than th HW covered under category 5.1 of schedule 1 of HW (MH&TM) Rules 2008 if the quantity of waste /used /spent oil is < 5 KL per annum

03. What is the mode of payment of CTE fee?

Instrument Demand Draft Infavour of Member Secretary, Rajasthan State

Pollution Control Board, payable at respective Regional Office

04. Where to submit the CTE application?

The application along with requisite documents shall be submitted either at the concerned Regional Office of the Board or at Head Office, Jaipur. However, where the competent authority to grant consent to establish is the Regional Officer, the consent application should be submitted to the respective Regional Officer.

05. Is there any provision to apply CTE application on-line?

The Board is in the process of upgrading the systems to accept the applications on line. For details visit RSPCB web site.

http://www.rpcb.nic.in/�


06. What are the areas as identified by CGWA as – safe areas, semi – critical areas, critical areas & over exploited areas?

The details are given in Annexure 7

07. Whether prior environmental clearance is a pre- requisite to submit the CTE application?

No. Requires submitting a notary affidavit on Rs 10/- stamp paper stating that no construction work will be taken up until EC is obtained. This requirement is applicable to the projects that attract the provisions of EIA Notification only

08. Whether conversion of land, wherever required, is a pre – requisite to submit CTE application?

Yes

09. Who is the authority to accord the CTE application?

Regional Officer • All projects under green category Projects under orange category except the following: • Hotel, Motel, Resort > 50 beds • Hotel, Motel, Resort located in water body or within 200 meters of

High Flood Level (HFL) of water body Projects under Red category with the following restrictions: • Building and construction projects < 5000 Sq.M but ≥ 2500 sq.m of

built up area or dwelling units ≥ 50 but < 100 units • Health care establishments, nursing homes and hospitals ≥ beds Head Office • All projects not covered above • All projects covered under EIA Notification 2006 and Aravali

Notification 1992 • In case any application is refused at the Regional Office Level, the

decision on the application submitted subsequently by the unit shall be taken by at RSPCB, Head Office level

(Ref: RSPCB Office Order dated 21-12-2010) 10. What is the maximum time period to process the CTE application?

Statutory time limit: Section 25(7) of Water (P&CP) Act, 1974 as amended: Four months on submission of application, complete in all aspects Section 21(4) of Air (P&CP) Act, 1981 as amended: Four months after receipt of the application Administrative time limits of RPCB:

Red category projects 6 weeks Orange category projects 4 weeks Green category projects 4 weeks


11. What is the mode of communication of the approval / rejection order of CTE?

Hard copy By Registered post

with ack. due Down loads From RSPCB web,

under implementation

12. Is there any appeal mechanism?

Section 28 (1) of Water (P&CP) Act, 1974 as amended: Any person aggrieved by the order made by the State Board under section 25, 26 and 27 may within 30 days from the date on which is communicated to him, prefer an appeal before Appellate Authority constituted by the State Government. Section 31 (1) of Air (P&CP) Act, 1981 as amended: Any person aggrieved by an order made by the State Board under this Act may, within thirty day from the date on which the order is communicated to him, prefer an appeal to Appellate Authority constituted by the State Government The appellate authority may entertain the appeal after the expiry of the said period of thirty days if such authority is satisfied that the appellant was prevented by sufficient cause from filing the appeal in time

13. Whether the CTE obtained from the board can be transferred to any other person?

Where a person to whom consent has been granted by the State Board, transfers his interest in the industry to other person, such consent shall be deemed to have been granted to such other person and he shall be bound to comply with all the conditions subject to which it was granted as if the consent was granted to him originally. Such changes shall be notified to the Board

14. What is the validity period for CTE?

CTE will be valid for a period of three years or till the commissioning of the project, which ever is earlier (RSPCB Office order dated. 10.08.2001)

15. Are there any standards notified for discharge of wastewater under E (P) Act, 1986?

Yes. G.S.R. 422 (E) dated 19.05.1993 and G.S.R. 801(E) dated 31.12.1993 by MoEF, GoI (Annexure 8)

16. Are there are any specific noise standards applicable to D.G. Sets?

Notification No. 371(E) dated 27.05.2002 - E (P) Act, 1986: Noise limit for Diesel Generator Sets (up to 1000 KVA) manufacture on or after the 1st July, 2003 • The maximum permissible sound pressure level for new diesel

generator (DG) sets with rated capacity up to 1000 KVA, manufactured on or after the 1st July, 2003 shall be 75 dB (A) at 1 meter from the enclosure surface

• The diesel generator sets should be provided with integral acoustic enclosure at the manufacturing stage itself

Noise limit for DG sets not covered above Noise from the DG set should be controlled by providing an acoustic enclosure on by treating the room acoustically, at the users end


The acoustic enclosure or acoustic treatment of the room shall be designed for minimum 25 dB (A). Insertion Loss or for meeting the ambient noise standards, whichever is on the higher side (if the actual ambient noise is on the higher side, it may not be possible to check the performance of the acoustic enclosure/acoustic treatment. Under such circumstances the performance may be checked for noise reduction up to actual ambient noise level, preferably, in the nighttime. The measurement for Insertion Loss may be done at different points at 0.5m from the acoustic enclosure/room, and then averaged The DG set shall be provided with proper exhaust muffler with Insertion Loss of minimum 25 dB (A) Requirement of certification Every manufacturer or importer of DG set to which these regulations apply must have valid certificates of type approval and also valid certificates of conformity of production for each year, for all the product models being manufactured or imported from 1st July 2003 with the noise limit specified in the Notification. The conformance label must contain the following information a. Name and address of the supplier (if the address is described in the owner’s manual, it may not be included in the label) b. Statement “This product confirms to the Environment (Protection) Rules, 1986” c. Noise limit viz. 75 dB (A) at 1m d. Type approval certificate number e. Date of manufacture of the product Notification No. S.O. 50(E) dated 11th January 2010 – E (P) Act 1986: A loud speaker or a public address system r any sound producing instrument or a musical instrument or sound amplifier shall not be used at night time (10.00 pm to 6.00 am) except in closed premises for communication within, like auditoria, conference rooms, community halls, banquet halls or during public emergency

17. Is there any guideline to calculate the minimum requirement of the stack of D.G set?

The CPCB had evolved the minimum height of the stack to be provided to the DG set and published in Emission Regulations Part IV: COINDS/26/1986-87. H= h+0.2 x ÖKVA

H Total height of stack in meter h Height of the building in meters where the

generator set is installed KVA

Total generator capacity of the set in KVA

Based on the above formula the minimum stack height to be provided


with different range of generator sets may be categorized as follows: For generator Sets Total height of stack in meter 50 KVA Ht. of the building +1.5 meter 50-100 KVA Ht. of the building +2.0 meter 100-150 KVA Ht. of the building +2.5 meter 150-200 KVA Ht. of the building +3.0 meter 200-250 KVA Ht. of the building +3.5 meter 250-300 KVA Ht. of the building +3.5 meter

18.Is there any standards notified for ambient noise level?

MoEF National Ambient Air Quality Standards dated 16th November 2009 (Annexure 9)

19. Where shall the ambient noise levels be monitored for compliance?

The ambient air quality standards in respect of noise as notified under E (P) Act, 1986 shall be monitored at the boundary of the project for compliance (Annexure 10)

20. Whether any procedures notified for handling solid waste?

MoEF had notified procedures and standards for handling municipal solid waste vide Municipal Solid Waste (Handling &Management) Rules, 2000(www.moef.nic.in)

21. Whether Building & Construction projects are required to apply for Consent To Operate?

Yes

22. Whether Building & Construction projects are required file water cess returns?

Yes If the projects consume water for different applications including domestic more than 10 KLD shall file the Water Cess returns in the prescribed format along with analysis report of treated effluent. The Central Government exempted industries consuming water less than 10 kl per day from the levy of cess, provided that no such exemption shall be applicable in case of industries generating ‘hazardous wastes’ as identified in clause (i) of Rule 3 of the HW (M&H) Rules 1989


Environmental Aspects and Guidance 5.0 Environmental Aspects The typical environmental aspects projects are discussed below: Land environment Impact on natural drainage system

Impact on surrounding land use campactability Impact on the public infrastructure such as on roads, parking, public water supply and power supply and sewerage system

Biological environment Impact on flora and fauna Water environment Impact due to ground water drawl

Impact due to discharge of black water and grey water Impact due to discharge of water from swimming pools

Air environment Impact during the construction stage – blasting for foundation, removal of top soil, raw material handling, bore drilling for tapping ground water

Noise environment Impact during the construction Impact due to operation of D.G sets

Solid waste Impact due to demolition waste Impact due to biodegradable and non biodegradable, including plastic waste and e-waste

Natural resources Consumption of power and water and the stress on the system 5.1 Environmental Norms S. No Description of the norms Notification

01. General Standards for Discharge of Effluents

Notification No. G.S.R 422 (E) dated 19.05.1993 and G.S.R 801 (E) dated 31.12.1993 issued under the provisions of E (P) Act 1986 (Annexure 8)

02. National Ambient Air Quality Standards

CPCB Notification No. B-29016/20/90/PCI-I dated 18th November 2009 (Annexure 9)

03. National Noise Ambient Air Quality Standards

The Noise Pollution (Regulation & Control) Rules, 2000 – S.O. 123 (E) dated 14th February 2000 and as amended in S.O. 1046 (E) dated 22.11.2000 (Annexure 10)

04. Noise Limit for Generator Sets Run With Diesel

Notification No. G.S.R 371 (E) dated 17th May, 2002 (Annexure 11)

05. The Ozone Depleting Substances

The Ozone Depleting Substances (Regulation & Control) Rules, 2000 – S.O. 670 (E) dated 19.07.2000 (www.moef.nic.in)

CHAPTER 5



5.2 Guidelines for the Project Developer

The project developer is advised to refer to the following documents:

• EIA guidance manual for Building construction, Townships and Area Development of Ministry of Environment & Forest, Government of India

• National Building Code of India 2005 • Development Control Rules – Town and Country Planning • Energy Conservation Building Code 2007 (www.bee-india.nic.in) • Energy Conservation Building Code (ECBC) – User Guide, July 2009 (www.bee-

india.nic.in) • Rating systems for water efficient fixtures – A way to sustainable water management in

India (Center for Science and Environment, New Delhi) • User’s handbook on solar water heaters (www.mnre.gov.in) Design layout - to explore the following depending on the site conditions / requirements • Dual plumbing arrangements • Area allotted for Sewage Treatment plant • Provision to connect to city sewer system • Parking requirement should meet the local body requirements and NBC 2005 • Area for green belt and lawns • Provision to tap the roof water • Provision for rain water harvesting structure • Provisions as per the Energy Conservation Building Code (ECBC) • Procurement of equipments with energy labeling

Estimation of water demand Proper care should be taken in estimating the peak water requirements and reliable source. The water requirements for different types of buildings should be estimated as given in Annexure 12 Estimation of adequate parking requirement The requirements should be assessed in a very realistic way by considering the diverse activities proposed in the project, location aspects and socio – economic levels of the expected users. Parking retirements as per the National Building Code of India, 2005 is given at Annexure 13. As per the MoEF requirements, a minimum of one car parking provision for a two bedroom apartment and two parking provisions for a three bedroom with 10% extra for visitors shall be provided. The adequacy of the access road to the project and free flow of traffic should be assessed.

http://www.bee-india.nic.in/�



http://www.mnre.gov.in/�

Good Practices

6.0 Water Conservation In view of critical shortage of water, conservation of water by rainwater harvesting and by use of recycled water to the maximum extent possible should be explored. In this regard the following provisions may be explored: • Provision for water conservation fixtures • Provision for water meter to monitor the consumption of water • Provision for dual plumbing systems • Provision to use treated waste water for cooling makeup purpose to conserve fresh

water consumption • Provision for collection of rainwater from rooftops and terraces and direct the same

either to a storage tank or to a recharging well 6.1 Parking Spaces Parking space provided for vehicles • For car, the minimum parking space to be 3m X 6m when individual parking space is

required and 2.75m X 5m when common parking space is required • Space for scooter/two wheeler and bicycle to be not less than 1.25 m2 and 1.00 m2

respectively • Area for each equivalent car space inclusive of circulation area is 23 m2 for open parking,

28 m2 for ground floor covered parking and 32 m2 for basement (Source: National Building Code of India, 2005) 6.2 Dual plumbing system and grey water treatment • Water from toilets is called black water (Sewage), while water from laundry, kitchens,

and baths is called grey water (sullage). • Grey water constitutes 70% of the wastewater, which can be treated by using simple and

cost-effective systems and can be reused for landscaping, external washing, and toilet flushing. Reusing grey water can reduce the dependence on municipal and bore water by up to 60%.

• Dual plumbing system separates grey water and black water at the source of generation, following which specific treatment options either for grey or black water can be adopted.

• Separating grey water and treating it onsite for reuse reduces the volume of the wastewater to be collected and treated and, hence, reduces the stress of public sewage lines and centralized wastewater treatment systems.

CHAPTER 6


6.3 Location of the Septic Tanks A sub-soil dispersion system shall not be closer than 18m from any source of drinking water, such as well, to mitigate the possibility of bacterial pollution of water supply. It shall also be as far removed from the nearest habitable building as economically feasible but not closer than 6m, to avoid damage to the structures. Under no circumstances shall effluent from a septic tank be allowed into an open channel drain or body of water without adequate treatment. 6.4 Energy Labeling Programme The energy-labeling program offers significant benefits to the consumers. It enables consumers to reduce their monthly energy bills while using Air Conditioners and provides information on energy use. There is wide variation in energy consumption of different makes of Air conditioners. This led to the continuous availability of inefficient Air conditioners in the market and purchase by consumers, leading to waste of precious and costly energy. The energy-labeling program sets out to correct this situation in the India Air conditioner market. BEE has prescribed minimum efficiency performance standards and the appliances are rated on the basis of energy efficiency indicated by suitable number of stars on the nameplate label. The no. of stars can vary from 1 to 5. Higher stars indicate higher energy efficiency and more energy bill savings for the customers Energy labeling program is mandatory from January 2010 for the following products: • Frost-free Refrigerators • Room Air Conditioners • TFL • Distribution Transformers 6.5 Energy Conservation Building Code (ECBC) The Energy Conservation Act, 2001 (52 of 2001) empowers the Central Government under Section 14(p) read with Section 56(2)(1) to prescribe Energy Conservation Building Code (ECBC). The code defines norms and standards for the energy performance of building and their components based on the climate zone in which they are located. In May 2007, the Ministry of Power, Government of India formally launched the ECBC for its voluntary adoption in the country. The code is applicable to buildings or building complexes that have a connected load of 500 kW or greater or a contract demand of 600 KVA or greater. Generally, buildings or complexes having conditioned area of 1,000 m2 or more will fall under this category. The code is presently under voluntary adoption in the country. The code would become mandatory as and when it is notified by the Central and State government in the official Gazette under clause (p) of 14 or clause (a) of 15 of the Energy Conservation Act 2001 (52 of 2001) The provisions of the Code apply to: • Building envelops, except for unconditioned storage or warehouses


• Mechanical systems and equipment, including heating, ventilating and air conditioning (HVAC)

• Service hot water heating • Interior and exterior lighting • Electric power and motors 6.6 ECBC User Guide 2009 The purpose of Energy Conservation Building Code (ECBC) is to provide minimum requirements for energy-efficient deign and construction of buildings and their systems. The building sector represents about 33%of electricity consumption in India, with commercial sector and residential sector accounting for 8% and 25% respectively. Estimates based on computer simulation models indicate that ECBC- complaint buildings can use 40 to 50% less energy than conventional buildings. It is estimated that the nationwide mandatory enforcement of the ECBC will yield annual savings of approximately 1.7 billion kWh. The ECBC is expected to overcome market barriers, which otherwise result in under-investment in building energy efficiency. The ECBC User Guide provides detailed guidance to building owners, designers, engineers, builders, energy consultants, and other on how to comply with the code. It provides expanded interpretation, examples, and supplementary information to assist in applying ECBC during the design and construction of new buildings as well as additions and alteration to existing buildings. This guide can also be used as a document by “authorities having jurisdiction” in the enforcement of the code once it is made mandatory. The guide follows the nomenclature of the code. It is written both as a reference and as an instructional guide, and can be helpful for anyone who is directly or indirectly involved in the design and construction of ECBC-complaint buildings 6.7 BEE Star Rating for Office Buildings Energy audit studies in buildings have shown large potential for energy savings both in government and commercial office buildings. Study of the available data has shown that there is an urgent need for improved energy efficiency of buildings. National commercial energy benchmarking initiative was taken up with a goal to establish a framework to standardize energy data collection, baseline setting for “typical” commercial buildings, energy performance target setting and monitoring, and use the information to improve energy efficiency in buildings. This information can help the users and other stakeholders to evaluate building energy efficiency and track improvements compared to other buildings and recognize the top performers. The Star Rating Program for buildings would create a demand in the market for energy efficient buildings based on actual performance of the building in terms of specific energy usage. This programme would rate office building on a 1-5 Star scale with 5 Star labeled buildings being the most efficient. Five categories of buildings – office buildings, hotels, hospitals, retail malls, and IT Parks in five climate zones in the country have been identified for this programme. Initially, the


programme targets the following 3 climatic zones for air-conditioned and non-air conditioned office buildings: • Warm and Humid • Composite • Hot and Dry To apply for rating of office buildings, BEE developed standardized formats for collection of actual energy consumption: data required includes building’s built up area, conditioned and non-conditioned area, type of building, hours of operation of the building in a day, climatic zone in which building is located, and other related information of the facility. 6.8 Cool Roofs Depending on the material and construction, a roof will have different properties that determine how it conducts heat to the inside of the building. “Cool Roofs” are roofs covered with a reflective coating that has a high emissivity property that is very effective in reflecting the sun’s energy way from the roof surface. These “cool roofs” are known to stay 100C to 160C cooler than a normal roof under a hot summer sun; this quality greatly reduces heat gain inside the building and the cooling load that needs to be met by the HVAC system (Source: Energy Conservation Building Code (ECBC -User Guide, 2009) 6.9 Good Practices in Design and Construction • Longer dimensions of buildings should face north and south (with a maximum deviation

of 50 off north) and shorter dimensions should face east and west. In multistoried apartments, the sides having openings should face either north or south

• A building designed according to solar path remains comparatively cool in summers and warm in winters, thus obviating the need for artificial heating or cooling

• For external lighting, 50% - 100% of outdoor lighting should be based on solar photovoltaic alone or in combination with other renewable sources of energy such as biomass

• The switches used for outdoor lighting generally do not take seasonal variation or a timer should be used that is sensitive to seasonal variations and adjusts on the basis of actual length of day/night

• Solar passive buildings are designed to provide thermal and visual comfort by using natural energy sources and sinks like solar radiation, outside air, wet surfaces, vegetation and so on. The solar passive buildings have potential to reduce energy demand by 5% - 20%

• Roof is the largest source of heat gain, especially in low-rise buildings. Hence, proper treatment of roof is necessary to reduce heat gains during daytime. Treatment of roofs provides comfort levels and reduces cooling loads inside a building. Thermally insulating the roof reduces the U-value (thermal conductivity) for the roof section. All exposed roof shall have a maximum U-factor of 0.261 W/m2 0C or a minimum R-value (the measure of its resistance to heat flow. The higher the R-value, the more the material insulates. It is the reciprocal of U-factor) of 3.5 m2 0C/W

• All heating and cooling equipment should meet the minimum efficiency requirements, as specified in the ECBC (Energy Conservation Building Code), 2007


• Solar water heating system should be explored. A solar water heater uses the energy from sun to heat water, which is used for different applications such as bathing, washing, cooking. The overall potential of solar water heating in India is estimated as 140 million sq.meters and about 1 million sq.meters of solar collector area has been realized

• Water saving fittings should be planned. An old single – flush toilet could use up to 12 liters of water per flush, while a standard dual-flush toilet uses just a quarter of this on a half-flush

• Use of electronic flushing system or magic eye sensor can further reduce the flow of water to 0.4 liter per flush, and waterless urinals use no water

• A standard showerhead may use up to 25 litres of water per minute, whereas water-efficient showerhead might use as little as 7 litres of water per minute which is less than a third of that consumed by standard showerhead

• Grey water after treatment should be explored for landscaping purpose in order to conserve fresh water intake. If no grey water or waste water treatment is undertaken on the site, the total landscape water requirement per annum should not exceed the total amount of rainwater colleted per annum

• Water demand in landscape should be reduced by planting native and low water consuming plants

• Providing dual plumbing system for separating wastewater and grey water and for using treated grey water should be explored. A wastewater treatment system should be provided only where sewerage network with STP is not available. In all the cases grey water recycling should be explored

• Construction and demolition waste management plan should be drawn • Waste should be segregated in to biodegradable and non biodegradable and proper

disposal plan should be prepared. All recyclables should be sent to recycling units. Should explore composting, vermin composting etc., to dispose biodegradable waste

• Re-use of swimming pool discharge water for toilet flushing purpose etc.

Checklist 7.0 Checklist for CTE

A. Documentation Check List S.No. Document Yes No Remarks 01. Completely filled application form duly signed

by authorized signatory

02. Document authorizing the applicant for signing application and other documents

03. Copy of memorandum of article of Association/Partnership deed

04. Demand Draft for consent fee 05. Copy of the duly signed project report 06. Certificate from Chartered Accountant for

capital investment (In case capital investment is 25 lakhs or more)

07. Copy of letter of land allotment/conversion letter from the competent authority

08. Copy of the site plan 09. Whether unit attracts provision of EIA

notification and if so EC clearance obtained?

10. Environmental Management Plan (For all Red category units and large/medium scale units in Orange and other category)

11. Legal undertaking in the prescribed format on non-judicial stamp paper of RS. 10/- only duly attested by notary public

B. Environmental Check List General

12.

Category of project (Red/Orange/Others)

13. Requirement of Consent To Establish (Water Act only/ Air Act only/ Both Acts)

C. Land Environment 14. Whether location falls under restrictions on

development projects in Aravali region?

15. Whether location falls under restrictions on development projects in Mount Abu zone?

16. Whether the site is located amidst any water body or located with in 200 meters of High Flood Level of any lake, reservoir, river or water bodies?

CHAPTER 7


17. Whether adequate parking space is proposed and the relevant codes of practices/norms are furnished?

18. Whether the proposed project is in conformity with the approved master plan/development plan of the area, if any?

19. Whether natural drainage system will be altered?

D. Water Environment 20. Whether estimation of water demand for peak

requirement is assessed?

21. Whether reliable source of water for peak demand is identified?

22. Whether it is proposed to use ground water? If yes, whether NOC from CGWA is required as per the norms? If yes, whether NOC from CGWA obtained?

23. Whether any rainwater harvesting structures proposed to re-charge ground water?

24. Whether water saving fittings is planned? 25. Whether proposing to provide dual plumbing

system? Whether dual plumbing system for using treated grey water for flushing the toilets or any other usage is explored?

26. Whether proposing to provide on site grey water treatment system with re-use facility?

27. Whether proposed to connect to the sewerage system of the city having STP?

28. Whether on site STP is proposed? If yes, whether STP is designed to meet the norms of the Board?

29. Whether adequate number of water meters proposed to record the water consumption as per cess criteria?

30. Whether all outlet(s) are properly specified? E. Air Environment

31. Whether all sources of air pollution identified and included in CTE application?

32. Whether dust generation during excavation, blasting and construction is addressed and planned with mitigation measures?

33. Whether minimum stack height is proposed as per the norms?

F. Solid Wastes 34. Whether all sources of hazardous wastes are

identified/ quantified/ categorized as per the norms?


35. Whether proposed method of disposal of hazardous wastes is identified?

36. Whether final disposal point for municipal solid waste is identified?

G. Noise Environment 37. Whether noise due to unit operations and DG

set (s) is addressed?

H. Green belt 38. Whether EMP outlined the green belt

development? Whether soil suitability and water requirement for green belt is addressed?

I. Natural Resources 39. Whether the connected load is 500 kW or

greater or a contract demand of 600 kVA or greater?

40. Whether the project developer is planning to adopt ECBC, which is at present voluntary adoption?

41. What level stars of air conditioners are planned (Ref: Energy Labeling Program of BEE – 1 to 5 Star Rating)?

42. Whether project developer is planning to apply for BEE Star Rating of Office Buildings, which is a voluntary at present)

43. Whether, for exterior lighting, a photo sensor or astronomical time switch that is capable of automatically turning off the exterior lighting when day light is available or the lighting is not required, is planned?

44. Whether for external lighting solar photovoltaic cells or any other renewable energy sources is explored?

45. Whether solar water heating system is explored?

46. Whether roof treatment system is explored to reduce the load on the cooling system?


===================================================================

ANNEXURES ===================================================================


Annexure - 1

FORM 1 (EIA Notification dated 14th September 2006 as amended 1st December 2009) (I) Basic Information S. No Item Details 1. Name of the project/s 2. S. No in the schedule 3. Proposed capacity/area/length/tonnage to be

handled/command area/lease area/number of wells to be drilled

4. New/expansion/modernization 5. Existing capacity/area etc 6. Category of project i.e. ‘A’ or ‘B’ 7. Does it attract the general condition? If yes, please

specify

8. Does it attract the specific condition? If yes, please specify

9. Location Plot/survey/khasra No Village Tehsil District State

10. Nearest railway station/airport along with distance in kms

11. Nearest town, city, district head quarters along with distance in kms

12. Village Panchayats, Zilla Parishad, Municipal Corporation, Local body (complete postal addresses with telephone no.s to be given)

13. Name of the applicant 14. Registered address 15. Address for correspondence:

Name Designation (Owner/partner/CEO) Address Pin code E-mail Telephone No. Fax No.

16. Details of alternative sites examined, if any. Location of these sites should be shown on a topo sheet

Village-District-State 1. 2. 3.

17. Interlinked projects 18. Whether separate application of interlinked project


has been submitted? 19. If yes, date of submission 20. If no, reason 21. Whether the proposal involves approval/clearance

under: if yes, details of the same and their status to be given

a. The Forest (Conservation) Act, 1980? b. The Wildlife (Protection) Act, 1972? c. The CRZ Notification, 1991?

22. Whether there is any Government order/policy relevant/relating to the site?

23. Forest land involved (hectares) 24. Whether there is any litigation pending against the

project and/or land in which the project is propose to be set up? a. Name of the Court b. Case No. c. Orders/directions of the Court, if any and its

relevance with the proposed project

(II) Activity 1. Construction, operation or decommissioning of the Project involving actions, which will cause physical changes in the locality (topography, land use, changes in water bodies, etc.) S. No. Information/Checklist confirmation Yes/No Details thereof (with Approximate

quantities /rates, wherever possible) with source of information data

1.1 Permanent or temporary change in land use, land cover or topography including increase in intensity of land use (with respect to local land use plan)

1.2 Clearance of existing land, vegetation and buildings?

1.3 Creation of new land uses? 1.4 Pre-construction investigations e.g.

bore houses, soil testing?

1.5 Construction works? 1.6 Demolition works? 1.7 Temporary sites used for construction

works or housing of construction workers?

1.8 Above ground buildings, structures or earthworks including linear structures, cut and fill or excavations

1.9 Underground works including mining or tunneling?


1.10 Reclamation works? 1.11 Dredging? 1.12 Offshore structures? 1.13 Production and manufacturing

processes?

1.14 Facilities for storage of goods or materials?

1.15 Facilities for treatment or disposal of solid waste or liquid effluents?

1.16 Facilities for long term housing of operational workers?

1.17 New road, rail or sea traffic during construction or operation?

1.18 New road, rail, air waterborne or other transport infrastructure including new or altered routes and stations, ports, airports etc?

1.19 Closure or diversion of existing transport routes or infrastructure leading to changes in traffic movements?

1.20 New or diverted transmission lines or pipelines?

1.21 Impoundment, damming, culverting, realignment or other changes to the hydrology of watercourses or aquifers?

1.22 Stream crossings? 1.23 Abstraction or transfers of water form

ground or surface waters?

1.24 Changes in water bodies or the land surface affecting drainage or run-off?

1.25 Transport of personnel or materials for construction, operation or decommissioning?

1.26 Long-term dismantling or decommissioning or restoration works?

1.27 Ongoing activity during decommissioning which could have an impact on the environment?

1.28 Influx of people to an area in either temporarily or permanently?

1.29 Introduction of alien species? 1.30 Loss of native species or genetic

diversity?

1.31 Any other actions?


2. Use of Natural resources for construction or operation of the Project (such as land, water, materials or energy, especially any resources which are non-renewable or in short supply): S. No. Information/Checklist confirmation Yes/No Details thereof (with Approximate


2.1 Land especially undeveloped or agricultural land (ha)

2.2 Water (expected source & competing users) unit: KLD

2.3 Minerals (MT) 2.4 Construction material – stone,

aggregates, sand / soil (expected source – MT)

2.5 Forests and timber (source – MT) 2.6 Energy including electricity and fuels

(source, competing users) Unit: fuel (MT), energy (MW)

2.7 Any other natural resources (use appropriate standard units)

3. Use, storage, transport, handling or production of substances or materials, which could be harmful to human health or the environment or raise concerns about actual or perceived risks to human health. S. No. Information/Checklist confirmation Yes/No Details thereof (with Approximate


3.1 Use of substances or materials, which are hazardous (as per MSIHC rules) to human health or the environment (flora, fauna, and water supplies)

3.2 Changes in occurrence of disease or affect disease vectors (e.g. insect or water borne diseases)

3.3 Affect the welfare of people e.g. by changing living conditions?

3.4 Vulnerable groups of people who could be affected by the project e.g. hospital patients, children, the elderly etc.,

3.5 Any other causes


4. Production of solid wastes during construction or operation or decommissioning (MT/month) S.No. Information/Checklist confirmation Yes/No Details thereof (with Approximate


4.1 Spoil, overburden or mine wastes 4.2 Municipal waste (domestic and or

commercial wastes)

4.3 Hazardous wastes (as per Hazardous Waste Management Rules)

4.4 Other industrial process wastes 4.5 Surplus product 4.6 Sewage sludge or other sludge from

effluent treatment

4.7 Construction or demolition wastes 4.8 Redundant machinery or equipment 4.9 Contaminated soils or other materials 4.10 Agricultural wastes 4.11 Other solid wastes 5. Release of pollutants or any hazardous, toxic or noxious substances to air (Kg/hr) S. No. Information/Checklist confirmation Yes/No Details thereof (with Approximate


5.1 Emissions from combustion of fossil fuels from stationary or mobile sources

5.2 Emissions from production processes 5.3 Emissions from materials handling

including storage or transport

5.4 Emissions from construction activities including plant and equipment

5.5 Dust or odours from handling of materials including construction materials, sewage and waste

5.6 Emissions from incineration of waste 5.7 Emissions from burning of waste in

open air (e.g. slash materials, construction debris)

5.8 Emissions from any other sources


6. Generation of Noise and Vibration, and Emissions of Light and Heat: S. No. Information/Checklist confirmation Yes/No Details thereof (with Approximate


6.1 From operation of equipment e.g. engines, ventilation plant, crushers

6.2 From industrial or similar processes 6.3 From construction or demolition 6.4 From blasting or piling 6.5 From construction or operational traffic 6.6 From lighting or cooling systems 6.7 From any other sources 7. Risks of contamination of land or water from releases of pollutants into the ground or into sewers, surface waters, groundwater, coastal waters or the sea: S. No. Information/Checklist confirmation Yes/No Details thereof (with Approximate


7.1 From handling, storage, use or spillage of hazardous materials

7.2 From discharge of sewage or other effluents to water or the land (expected mode and place of discharge)

7.3 By deposition of pollutants emitted to air into the land or into water

7.4 From any other sources 7.5 Is there a risk of long term build up of

pollutants in the environment from these sources?

8. Risk of accidents during construction or operation of the Project, which could affect human health or the environment S. No. Information/Checklist confirmation Yes/No Details thereof (with Approximate


8.1 From explosions, spillages, fires etc from storage, handling, use or production of hazardous substances

8.2 From any other causes 8.3 Could the project be affected by natural

disasters causing environmental damage (e.g. floods, earthquakes, landslides, cloudburst etc)?


9. Factors which should be considered (such as consequential development) which could lead to environmental effects or the potential for cumulative impacts with other existing or planned activities in the locality S. No. Information/Checklist confirmation Yes/No Details thereof (with Approximate


9.1 Lead to development of supporting. lities, ancillary development or development stimulated by the project which could have impact on the environment e.g. • Supporting infrastructure (roads, power supply, waste or waste water treatment, etc.) • Housing development • Extractive industries • Supply industries • Other

9.2 Lead to after-use of the site, which could havean impact on the environment

9.3 Set a precedent for later developments 9.4 Have cumulative effects due to

proximity to other existing or planned projects with similar effects

(III) Environmental Sensitivity S. No. Areas Name/

Identity Aerial distance (within 15 km.) Proposed project location boundary

1 Areas protected under international conventions, national or local legislation for their ecological, landscape, cultural or other related value

2 Areas which are important or sensitive for ecological reasons - Wetlands, watercourses or other water bodies, coastal zone, biospheres, mountains, forests

3 Areas used by protected, important or sensitive species of flora or fauna for breeding, nesting, foraging, resting, over wintering, migration

4 Inland, coastal, marine or underground waters


5 State, National boundaries 6 Routes or facilities used by the public

for access to recreation or other tourist, pilgrim areas

7 Defence installations 8 Densely populated or built-up area 9 Areas occupied by sensitive man-made

land uses (hospitals, schools, places of worship, community facilities)

10 Areas containing important, high quality or scarce resources (ground water resources, surface resources, forestry, agriculture, fisheries, tourism, minerals)

11 Areas already subjected to pollution or environmental damage. (Those where existing legal environmental standards are exceeded)

12 Areas susceptible to natural hazard which could cause the project to present environmental problems (Earthquakes, subsidence, landslides, erosion, flooding or extreme or adverse climatic conditions)

(IV). Proposed Terms of Reference for EIA studies ………………………………………………………………………………………………………………………………………………………………………………………………………………………… I hereby given undertaking that the data and information given in the application and enclosures are true to the best of my knowledge and belief and I am aware that if any part of the data and information submitted id found to be false or misleading at any stage, the project will be rejected and clearance give, if any to the project will be revoked at our risk and cost: Date: __________________ Place: _________________

Signature of the applicant

With Name and Full Address (Project proponent/Authorized signatory)


Note: 1. The projects involving clearance under Coastal Regulation Zone Notification, 1991 shall submit with the application a CRZ map duly demarcated by one of the authorized agencies, showing the project activities, w.r.t CRZ (at the stage of TOR) and the recommendations of the State Coastal Zone Management Authority (at the stage of EC). Simultaneous action shall also be taken to obtain the requisite clearance under the provisions of the CRZ Notification, 1991 for the activities to be located in the CRZ 2. The projects to be located within 10km of the National Parks, Sanctuaries, Biosphere Reserves, Migratory corridors of the Wild animals, the project proponent shall submit the map duly authenticated by Chief Wildlife Warden showing these features vis-à-vis the project location and the recommendations of comments of the Chief Wildlife Warden thereon (at the stage of EC) 3. All correspondence with the Ministry of Environment & Forests including submission of application for TOR/Environmental Clearance, subsequent clarifications, as may be required from time to time, participation in the EAC meeting on behalf of the project proponent shall be made by the authorized signatory only. The authorized signatory should also submit a document in support of his claim of being an authorized signatory for the specific project.”


Annexure - 2

FORM-1 A (only for construction projects listed under item 8 of the Schedule of EIA Notification)

Check List of Environmental Impacts (Project proponents are required to provide full information and wherever necessary attach explanatory notes with the Form and submit along with proposed environmental management plan & monitoring programme) 1. Land Environment (Attach panoramic view of the project site and the vicinity) 1.1. Will the existing land use gets significantly altered from the project that is not consistent with the surroundings? (Proposed land use must conform to the approved Master Plan /Development Plan of the area. Change of land use if any and the statutory approval from the competent authority be submitted). Attach Maps of (i) site location, (ii) surrounding features of the proposed site (within 500 meters) and (iii) the site (indicating levels & contours) to appropriate scales. If not available attach only conceptual plans. 1.2. List out all the major project requirements in terms of the land area, built up area, water consumption, power requirement, connectivity, community facilities, parking needs etc. 1.3. What are the likely impacts of the proposed activity on the existing facilities adjacent to the proposed site? (Such as open spaces, community facilities, details of the existing landuse, and disturbance to the local ecology). 1.4. Will there be any significant land disturbance resulting in erosion, subsidence & instability? (Details of soil type, slope analysis, vulnerability to subsidence, seismicity etc may be given). 1.5. Will the proposal involve alteration of natural drainage systems? (Give details on a contour map showing the natural drainage near the proposed project site) 1.6. What are the quantities of earthwork involved in the construction activity-cutting, filling, reclamation etc. (Give details of the quantities of earthwork involved, transport of fill materials from outside the site etc.) 1.7. Give details regarding water supply, waste handling etc during the construction period 1.8. Will the low lying areas & wetlands get altered? (Provide details of how low lying and wetlands are getting modified from the proposed activity) 1.9. Whether construction debris & waste during construction cause health hazard? (Give quantities of various types of wastes generated during construction including the construction labour and the means of disposal)


2. Water Environment 2.1. Give the total quantity of water requirement for the proposed project with the breakup of requirements for various uses. How will the water requirement met? State the sources & quantities and furnish a water balance statement. 2.2. What is the capacity (dependable flow or yield) of the proposed source of water? 2.3. What is the quality of water required, in case, the supply is not from a municipal source? (Provide physical, chemical, biological characteristics with class of water quality) 2.4. How much of the water requirement can be met from the recycling of treated wastewater? (Give the details of quantities, sources and usage) 2.5. Will there be diversion of water from other users? (Please assess the impacts of the project on other existing uses and quantities of consumption) 2.6. What is the incremental pollution load from wastewater generated from the proposed activity? (Give details of the quantities and composition of wastewater generated from the proposed activity) 2.7. Give details of the water requirements met from water harvesting? Furnish details of the facilities created. 2.8. What would be the impact of the land use changes occurring due to the proposed project on the runoff characteristics (quantitative as well as qualitative) of the area in the post construction phase on a long-term basis? Would it aggravate the problems of flooding or water logging in any way? 2.9.What are the impacts of the proposal on the ground water? (Will there be tapping of ground water; give the details of ground water table, recharging capacity, and approvals obtained from competent authority, if any) 2.10.What precautions/measures are taken to prevent the run-off from construction activities polluting land & aquifers? (Give details of quantities and the measures taken to avoid the adverse impacts) 2.11. How is the storm water from within the site managed?(State the provisions made to avoid flooding of the area, details of the drainage facilities provided along with a site layout indication contour levels) 2.12.Will the deployment of construction laborers particularly in the peak period lead to unsanitary conditions around the project site (Justify with proper explanation) 2.13.What on-site facilities are provided for the collection, treatment & safe disposal of sewage? (Give details of the quantities of wastewater generation, treatment capacities with technology & facilities for recycling and disposal) 2.14. Give details of dual plumbing system if treated waste used is used for flushing of toilets or any other use.


3. Vegetation 3.1.Is they’re any threat of the project to the biodiversity? (Give a description of the local ecosystem with its unique features, if any) 3.2. Will the construction involve extensive clearing or modification of vegetation? (Provide a detailed account of the trees & vegetation affected by the project) 3.3.What are the measures proposed to be taken to minimize the likely impacts on important site features (Give details of proposal for tree plantation, landscaping, creation of water bodies etc along with a layout plan to an appropriate scale) 4. Fauna 4.1.Is there likely to be any displacement of fauna- both terrestrial and aquatic or creation of barriers for their movement? Provide the details. 4.2. Any direct or indirect impacts on the avifauna of the area? Provide details. 4.3. Prescribe measures such as corridors, fish ladders etc to mitigate adverse impacts on fauna 5. Air Environment 5.1. Will the project increase atmospheric concentration of gases & result in heat islands? (Give details of background air quality levels with predicted values based on dispersion models taking into account the increased traffic generation as a result of the proposed constructions) 5.2. What are the impacts on generation of dust, smoke, odorous fumes or other hazardous gases? Give details in relation to all the meteorological parameters. 5.3. Will the proposal create shortage of parking space for vehicles? Furnish details of the present level of transport infrastructure and measures proposed for improvement including the traffic management at the entry & exit to the project site. 5.4. Provide details of the movement patterns with internal roads, bicycle tracks, pedestrian pathways, footpaths etc., with areas under each category. 5.5. Will there be significant increase in traffic noise & vibrations? Give details of the sources and the measures proposed for mitigation of the above. 5.6. What will be the impact of DG sets & other equipment on noise levels & vibration in & ambient air quality around the project site? Provide details.


6. Aesthetics 6.1. Will the proposed constructions in any way result in the obstruction of a view, scenic amenity or landscapes? Are these considerations taken into account by the proponents? 6.2. Will there be any adverse impacts from new constructions on the existing structures? What are the considerations taken into account? 6.3. Whether there are any local considerations of urban form & urban design influencing the design criteria? They may be explicitly spelt out. 6.4. Are there any anthropological or archaeological sites or artifacts nearby? State if any other significant features in the vicinity of the proposed site have been considered. 7. Socio-Economic Aspects 7.1. Will the proposal result in any changes to the demographic structure of local population? Provide the details. 7.2. Give details of the existing social infrastructure around the proposed project 7.3. Will the project cause adverse effects on local communities, disturbance to sacred sites or other cultural values? What are the safeguards proposed? 8. Building Materials 8.1. May involve the use of building materials with high-embodied energy. Are the construction materials produced with energy efficient processes? (Give details of energy conservation measures in the selection of building materials and their energy efficiency) 8.2. Transport and handling of materials during construction may result in pollution, noise & public nuisance. What measures are taken to minimize the impacts? 8.3. Are recycled materials used in roads and structures? State the extent of savings achieved? 8.4. Give details of the methods of collection, segregation & disposal of the garbage generated during the operation phases of the project. 9. Energy Conservation 9.1. Give details of the power requirements, source of supply, backup source etc. What is the energy consumption assumed per square foot of built-up area? How have you tried to minimize energy consumption? 9.2. What type of, and capacity of, power back-up to you plan to provide?


9.3. What are the characteristics of the glass you plan to use? Provide specifications of its characteristics related to both short wave and long wave radiation? 9.4. What passive solar architectural features are being used in the building? Illustrate the applications made in the proposed project. 9.5. Does the layout of streets & buildings maximise the potential for solar energy devices? Have you considered the use of street lighting, emergency lighting and solar hot water systems for use in the building complex? Substantiate with details. 9.6. Is shading effectively used to reduce cooling/heating loads? What principles have been used to maximize the shading of Walls on the East and the West and the Roof? How much energy saving has been effected? 9.7. Do the structures use energy-efficient space conditioning, lighting and mechanical systems? Provide technical details. Provide details of the transformers and motor efficiencies, lighting intensity and air-conditioning load assumptions? Are you using CFC and HCFC free chillers? Provide specifications. 9.8. What are the likely effects of the building activity in altering the micro-climates? Provide a self assessment on the likely impacts of the proposed construction on creation of heat island & inversion effects? 9.9. What are the thermal characteristics of the building envelope? (a) roof; (b) external walls; and (c) fenestration? Give details of the material used and the U-values or the R values of the individual components. 9.10. What precautions & safety measures are proposed against fire hazards? Furnish details of emergency plans. 9.11. If you are using glass as wall material provides details and specifications including emissivity and thermal characteristics. 9.12. What is the rate of air infiltration into the building? Provide details of how you are mitigating the effects of infiltration. 9.13. To what extent the non-conventional energy technologies are utilised in the overall energy consumption? Provide details of the renewable energy technologies used. 10. Environment Management Plan The Environment Management Plan would consist of all mitigation measures for each item wise activity to be undertaken during the construction, operation and the entire life cycle to minimize adverse environmental impacts as a result of the activities of the project. It would also delineate the environmental monitoring plan for compliance of various environmental regulations. It will state the steps to be taken in case of emergency such as accidents at the site including fire.


Annexure - 3 Performa Affidavit for CTE/CTO

I, _______________ (with name and designation) S/o Shri __________________ Resident of __________________ do solemnly affirm and declare as under:-

1. That I am responsible for establishing / operating the unit named M/s. _________________________ (Name & address of the unit).

2. That, I, ____________________ (with name and designation) am authorized to sign the consent application form and other enclosures with the application.

3. That the plot area of the unit is ____________________ Sq. Meters.

4. That the number of workers to carry out various activities in the unit is _________________________.

5. That the total number of employees proposed in the unit is _______________.

6. That the total capital investment on the project is Rs. _________________.

7. That this Consent to Establish/Operate is being obtained for the project from ________________ up to _________________. In case of any increase/change in capacity or addition/modification/alteration or change in the project or discharge points, we will obtain fresh Consent to Establish.

8. That the quantity of trade/domestic effluent shall not exceed __________ KLD. The mode of disposal shall be ________________. In case of any increase in quantity of effluent or alteration in outlet or mode of disposal, we shall obtain prior consent from the Board.

9. That all adequate measures for control and treatment of water/air pollution from the various processes/activities will be taken to meet the prescribed standards as per the Environment (Protection) Rules, 1986 as amended.

10. That the adequate pollution control measures will be provided to meet the prescribed standards

11. That the adequate pollution control measures shall be taken to meet the prescribed ambient noise standards.

12. That if Diesel Generator Sets (of capacity 5 KVA or more) is installed, it will be Eco-Friendly or with inbuilt acoustic enclosures to meet the prescribed norms w.r.t. Noise as per the Gazette Notification on Ministry of Environment & Forests, Government of India dated 2.1.1999. Adequate stack height with D.G. Set(s) shall also be provided and maintained and shall submit noise monitoring report.

13. That all orders and directions issued by the Board from time to time will be complied with.


14. That the name and addresses of Managing Director or other working Directors or Partner are ____________ . In case of any change, the same will be intimated to the Board.

VERIFICATION

Verified at _____________ on this __________ (day, month and year) that the above contents of this affidavit are true and correct to the best of my knowledge and belief and nothing has been concealed there from.

DEPONENT

Note: The aforementioned Affidavit must be duly signed by the Deponent and duly attested by the Notary Public thereof.

Note: Please strike out whatever is not applicable.


Annexure - 4 Classification of Projects for Consent Fee Purpose

S.No Categorization Type of project 1 Appendix – A projects 37. Building and Construction Project ≥

20000 Sq.M built up area 38. Township and Area Development project ≥ 50 ha or dwelling unit ≥ 100 83. Hotels, Motels, Resorts i) > 100 beds if located in the town having Divisional Head Quarter or > 200 beds if located else where, or /and ii) Covered under EIA Notification 2006 /Aravali Notification 1992 or/and iii) Located in water body /within 200mts of HFL of water body

2 Appendix – B Projects 1. Hotels, Motels, Resorts (Lodging and Boarding) having ≤ 200 beds but ≥ 25 beds other than following: i) Having > 100 beds if located in the town having Divisional Head Quarter, or /and ii) Covered under EIA Notification 2006 /Aravali Notification 1992 or/and iii) Located in water body /within 200mts of HFL of water body 2.Restaurant ≥ 25 seats 22. Building and Construction projects ≥ 2500 Sq.M but < 20,000 sq.m built up area 23. Township and Area development project ≥ 5ha but < 50 ha and or dwelling units ≥ 50 but <100 units 64. Establishments/ activities having D.G set (More than 100 KVA) 68. Marriage garden, community center and club with kitchen facilities

Ref: Notification dated 10 December 2010, DoE, Government of Rajasthan


Annexure - 5 Consent To Establish Fee (Schedule IV) - Water Act

S. No Capital Investment of the Industry Consent Fee to Establish (Rs)

(Rs.) Appendix A Appendix B Other than Appendix A and B

1 Upto 5 Lacs 3,000 2,000 1,000

2 More than 5 Lacs upto 10 Lacs 4,500 3,000 1,500



5 More than 50 Lacs upto 1 Crore 15,000 10,000 5,000

6 More than 1 Crore upto 5 Crore 18,000 12,000 6,000





11 More than 100 Crore upto 250 Crore 1,05,000 70,000 35,000


13 More than 500 Crore upto 750 Crore 1,50,000 1,00,000 50,000


15 Above 1000 Crore 2,25,000 1,50,000 75,000 Refer Notification dated 10th December, 2010 for details, DoE, Rajasthan

Note: 1. The categorization of the projects is as Notified by the DOE, Government of Rajasthan vide dated

10th December, 2010 2. All projects requiring environmental clearance under the Environmental (Protection) Act, 1986

shall pay an extra amount of Rs. 15,000/- as one time consent fee to establish in addition to that mentioned in Schedule.

3. All industries/process/projects/activities generating HW as defined under the HW (MH&TM) Rules 2008 and requiring authorization thereunder, the application for consent shall be accompanied with fee equal to one and half times of the amount of fee prescribed under the schedule, other than th HW covered under category 5.1 of schedule 1 of HW (MH&TM) Rules 2008 if the quantity of waste /used /spent oil is < 5 KL per annum


Annexure - 6 Consent To Establish Fee (Schedule IV) - Air Act

S.

No Capital Investment of the Industry Consent Fee to Establish (Rs)

(Rs.) Appendix A Appendix B Other than Appendix A and B

1 Upto 5 Lacs 3,000 2,000 1,000




5 More than 50 Lacs upto 1 Crore 15,000 10,000 5,000










15 Above 1000 Crore 2,25,000 1,50,000 75,000 Refer DOE, Rajasthan Notification dated 10th December, 2010 for details

Note: 1. The categorization of the projects is as Notified by the DOE, Government of Rajasthan vide dated

10th December, 2010 2. All projects requiring environmental clearance under the Environmental (Protection) Act, 1986

shall pay an extra amount of Rs. 15,000/- as one time consent fee to establish in addition to that mentioned in Schedule.

3. All industries/process/projects/activities generating HW as defined under the HW (MH&TM) Rules 2008 and requiring authorization thereunder, the application for consent shall be accompanied with fee equal to one and half times of the amount of fee prescribed under the schedule, other than th HW covered under category 5.1 of schedule 1 of HW (MH&TM) Rules 2008 if the quantity of waste /used /spent oil is < 5 KL per annum


Annexure - 7

Areas as identified by CGWA

S.No District No of Blocks Safe Semi-Critical Critical Over-Exploited

1 2 3 4 5 6 7

1 Ajmer 8 1.kekri 2. Masuda

1.Arain 2.Bhinai 3.jawala 4,.3Peesangan 5.Silora 6.srinagar

2 Alwar 14 1.Thanagaji

1.Bahror 2.Bansur 3.ktathumar 4. kishangarhbas 5.kotkasim 6.Laxmangarh 7.Mandawar 8.Neemrana 9.Rajgarh 10.Ramgarh 11.Raini 12.Tijara 13.Umrain

3 Banswara 8 1. Pipalkunt

1.Anandpuri 2.Bagidaura 3.Ghatol 4.Kushalgarh 5.Sajjangarh 6.Talwara

Gadi

4 Baran 7 1. Chhabra 2.kishangarh 3. Shabad

1.chhipabarod 1.Anta 1.Atru 2.Baran

5 Barmer 8 1.Chuhtan 2.Singhri

1.Bayatu 2. Balotra 3.Dhorimanna 4.Shiva

6 Bharatpur 9

1. Deeg 2. Kaman 3. Kumher 4. Nagar 5. Rupwas

1.Bayana 1. Nadbai 2. Sewar 3. Weir

7 Bhilwara 11 1. Kotadi 2. Shaara 3. Shahpura

1.Asind 2.Baneda 3.Hurda 4.Jahajpur 5.Mandal 6.Mandalgarh 7.Raipur 8.suwana

8 Bikaner 5 1. Lunkaransar - 1. Dungargarh 1. Bikaner


2. Kolayat - 2. Nokha

9

Bundi

4

-

1. Kesorai Patan 2. Talera

1.Hindoli 2. Nainwa

10

Chittorgarh

14

-

1. Bhainsrorgarh

-

1. Amod 2. Bari Sadri 3. Begun 4. Bhadesar 5. Bhopalsagar 6. Chhotisadri 7. Chittorgarh 8. Dungla 9. Gangrar 10. Kapasan 11. Nimbahera 12. Pratapgarh 13. Rashmi

11

Churu

6

1. Churu 2. Atangarh 3. Sardarshahar

-

1. Sujangarh

1. Rajgarh

12

Dausa

5

1. Bandikui 2. Dausa 3. Lalsot 4. Mahua 5. Sirai

13

Dholpur

4

1. Bari

1. Baseri

1. Dholpur 2. Rajakhera

14

Dungarpur

5

1. Aspur

1. Bichhiwara 2. Dungarpur

1. Sagwara 2. Simalwara

15

Ganganagar

7

1. Anupgarh 2. Ganganagar 3. Karanpur 4. Padampur 5. Raisingh nagar 6. Sadulshahar 7. Suratgarh

16

Hanumangarh

3

1. Bhadra 2. Hanumangarh 3. Nohar


17

Jaipur

13

1. Dudu 2. Phagi

1. Amer 2. Bairath 3. Bassi 4. Chaksu 5. Govindgarh 6. Jamwa Ramgarh 7. Jhotwara 8. Kotputli 9. Sambher 10. Sanganer 11. Shahpura

18

Jaisalmer

3

1. Sam

1. Jaisalmer 2. Sankra

19

Jalore

7

1. Ahore 2. Bhinmal 3. Jalore 4. Jaswantpura 5. Raniwara 6. Sanchore 7. Sayla

20

Jhalawar

6

1. Bakani 2. Dag 3. Jhalra Patan 4. Khanpur

1. Manoha Thana 2. Pirawa

21

Jhunjhunu

8

1. Alsisar

1. Bhuhana 2. Chirawa 3. Jhunjhunu 4. Khetri 5. Nawalgarh 6. Surajgarh 7. Udaipurwati

22

Jodhpur

9

1. Bap

1. Phalodi

1. Luni 2. Shergarh

1. Balesar 2. Bhopalgarh 3. Bilara 4. Mandore 5. Osaian

23

Karauli

5

1. Nadauti

1. Sapotra

1. Hindaun 2. Karauli 3. Todabhim

24

Kota

5

1. Sultanpur

1. Itawa 2. Khairabad 3. Ladpura 4. Sangod


25

Nagaur

11

1. Nagaur

1. Ladnu

1. Jayal 2. Makrana

1. Degana 2. Didwana 3. Kuchaman 4. Merla 5. Mundwa 6. Parbaisar 7. Riyan

26

Pali

10

1. Bali 2. Desuri 3. Pali 4. Raipur 5. Rohit

1. Jaitaran 2. Kharchi 3. Rani 4. Sojat 5. Sumerpur

27

Rajsamand

7

1. Railmagra 2. Rajsamand

1. Amet 2. Bhim 3. Deogarh 4. Khamnor 5. Kumbhalgarh

28

Sawaimadhopur

5

1. Bamanwas 2. Bonli 3. Khandar

1. Gangapur 2. Sawai Madhopur

29

Sikar

8

1. Fatehpur

1. Danta Ramgarh 2. Dhod 3. Khandella 4. Lachhmangarh 5. Neem Ka Thana 6. Piprali 7. Sri Madhopur

30

Sirohi

5

1. Abu Road 2. Pindwara 3. Sirohi

1. Reodar 2. Sheoganj

31

Tonk

6

1. Deoli 2. Malpura 3. Newai 4. Toda Rai Singh 5. Tonk

1. Untara

32

Udaipur

11

1. Kherwara 2. Kotra 3. Sarada

1. Badgaon 2. Bhinder 3. Dhariawad 4. Girwa 5. Gogunda 6. Jhadot 7. Mavli 8. Salumber

Total 237 32 14 50 140 (Source: CGWA No: 21-4/Guidelines/CGWA/2009-832 dated 14.10. 2009)


Annexure - 8 General Standards for Discharge of Effluents

S.

No Parameter Standards

Inland surface water

Public sewers Land for irrigation

Marine coastal areas

(a) (b) (c) (d) 1 Color & odour * ------- * * 2 Suspended solids

mg/l, Max 100 600 200 1. For process waste

water-100 2. For cooling water effluent 10% above total suspended matter of influent

3 Particle size of suspended solids

Shall pass 850 Micron IS sieve

-- -- 1. Floatable solids max. 3 mm 2. Settleable solids max. 850 microns

4 pH Value 5.5 to 9.0 5.5 to 9.0 5.5 to 9.0 5.5 to 9.0 5 Temperature Shall not exceed 50

C above the receiving water temperature

-- -- Shall not exceed 50 C above the receiving water temperature

6 Oil and grease mg/l Max.

10 20 10 20

7 Total residual chlorine mg/l Max.

1.0 -- -- 1.0

8 Ammonical Nitrogen (as N), mg/l Max.

50 50 -- 50

9 Total Kjeldahl nitrogen (as NH3), mg/l Max.

100 -- -- 100

10 Free ammonia (as NH3), mg/l Max.

5.0 -- -- 5.0

11 Bio-chemical oxygen demand (3 days at 270 C), mg/l max.

30 350 100 100

12 Chemical oxygen demand, mg/l max.

250 -- -- 250

13 Arsenic (as As), mg/l max.

0.2 0.2 0.2 0.2

14 Mercury (as Hg), mg/l max.

0.01 0.01 -- 0.01

15 Lead (as Pb), mg/l max.

0.1 1.0 -- 2.0

16 Cadmium (as Cd), mg/l max.

2.0 1.0 -- 2.0

17 Hexavalent chromium (as Cr +6), mg/l max.

0.1 2.0 -- 1.0


18 Total chromium (as Cr), mg/l max.

2.0 2.0 -- 2.0

19 Copper (as Cu), mg/l max.

3.0 3.0 -- 3.0

20 Zinc (as Zn), mg/l max.

5.0 15 -- 15

21 Selenium (as Se), mg/l max.

0.05 0.05 -- 0.05

22 Nickel (as Ni), mg/l max.

3.0 3.0 -- 5.0

23 Cyanide (as CN), mg/l max.

0.2 2.0 0.2 0.2

24 Fluoride (as F), mg/l max.

2.0 15 -- 15

25 Dissolved phosphates (as P), mg/l max.

5.0 -- -- --

26 Sulphide (as S), mg/l max.

2.0 -- -- 5.0

27 Phenolic compounds (as C6H5OH), mg/l max.

1.0 5.0 -- 5.0

28 Radio active materials: a. Alpha emitter

micro curie/ml 10-7 10-7 10-8 10-7

b. Beta emitter micro curie/ml

10-6 10-6 10-7 10-6

29 Bio-assay test 90% survival of fish after 96 hours in 100% effluent

90% survival of fish after 96 hours in 100% effluent



30 Manganese (as Mn), mg/l

2 2 -- 2

31 Iron (as Fe), mg/l 3 3 -- 3 32 Vanadium (as V),

mg/l 0.2 0.2 -- 0.2

33 Nitrate nitrogen, mg/l

10 -- -- 20

* All efforts should be made to remove colour and unpleasant odour as far as practicable These standards shall be applicable for industries, operations or processes other than those industries, operations or process for which standards have been specified of the Environment Protection Rules, 1989 Source: G.S.R 422 (E) dated 19.05.1993 and G.S.R 801 (E) dated 31.12.1993 issued under the provisions of E (P) Act 1986


Annexure - 9 National Ambient Air Quality Standards (NAAQS)

S.

No Pollutant Time

Weighted Average

Concentration in Ambient Air Industrial,

Residential, Rural and other areas

Ecologically sensitive area (notified by

central government)

Methods of measurement

(1) (2) (3) (4) (5) (6) 1 Sulphur dioxide

(SO2), μg/m3 Annual* 24 hours**

50 80

20 80

-Improved West & Gaeke -Ultraviolet fluorescence

2 Nitrogen Dioxide (NO2), μg/m3

Annual* 24 hours**

40 80

30 80

-Modified Jacob & Hochheiser (Na- arsenite) -Chemiluminescence

3 Particulate Matter (Size less than 10μm) or PM10μg/m3

Annual* 24 hours**

60 100

60 100

- Gravimetric - TOEM - Beta attenuation

4 Particulate Matter (Size less than 2.5μm) or PM2.5μg/m3

Annual* 24 hours**

40 60

40 60

- Gravimetric - TOEM - Beta attenuation

5 Ozone (O3) μg/m3

8 hours** 1 hour**

100 180

100 180

- UV photometric - Chemiluminescence - Chemical method

6 Lead (Pb) μg/m3 Annual* 24 hours**

0.50 1.0

0.50 1.0

-AAS/ICP method after sampling on EPM 2000 or equivalent filter paper -ED-XRF using Teflon filter

7 Carbon Monoxide (CO) mg/ m3

8 hours** 1 hour**

02 04

02 04

-Non Dispersive Infra Red (NDIR) spectroscopy

8 Ammonia (NH3) μg/m3

Annual* 24 hours**

100 400

100 400

- Chemiluminescence - Indophenol blue method

9 Benzene (C6H6) μg/m3

Annual* 05 05 -Gas chromatography based continuous analyzer -Adsorption and Desorption followed by GC analysis

10 Benzo(a)Pyrene (BaP) – particulate phase

Annual* 01 01 -Solvent extraction followed by HPLC/GC analysis


only, ng/m3 11 Arsenic (As)

ng/m3 Annual* 06 06 -AAS/ICP method after

sampling on EPM 2000 or equivalent filter paper

12 Nickel (Ni) ng/m3

Annual* 20 20 -AAS/ICP method after sampling on EPM 2000 or equivalent filter paper

* Annual arithmetic mean of minimum 104 measurements in a year at a particular site taken twice a week 24 hourly at uniform intervals ** 24 hourly or 08 hourly or 01 hourly monitored values, as applicable, shall be complied with 98% of the time in a year. 2% of the time, they may exceed the limits but not on two consecutive days of monitoring. Note: Whenever and wherever monitoring results on two consecutive days of monitoring exceed the limits specified above for the respective category, it shall be considered adequate reason to institute regular or continuous monitoring and further investigation (Source: MoEF Notification dated 16th November 2009)


Annexure -10 Noise Ambient Air Quality Standards

Area code Category of area Limits in db (A) Leq

Day time Night time A Industrial area 75 70 B Commercial area 65 55 C Residential area 55 45 D Silence zone 50 40

Note: 1. Day time shall mean from 6.00 a.m. to 10.00 p.m. 2. Night time shall mean from 10.00 p.m. to 6.00 a.m. 3. Silence zone is an area comprising not less than 100 meters around hospitals, educational institutions, courts, religious places or any other area, which is declared as such by the competent authority. 4. Mixed categories of areas may be declared as one of the four above-mentioned categories by the competent authority. * dB(A) Leq denotes the time weighted average of the level of sound in decibels on scale A which is relatable to human hearing. A “decibel” is a unit in which noise is measured. “A”, in dB(A) Leq, denotes the frequency weighting in the measurement of noise and corresponds to frequency response characteristics of the human ear. Leq: It is an energy mean of the noise level over a specified period. (Source: Noise pollution (Regulation and control) Rules, 2000)


Annexure - 11 Noise Limits for Generator Sets run with Diesel

1. Noise limit for diesel generator sets (up to 1000 KVA) manufacture on or after the 1st July 2003 The maximum permissible sound pressure level for new diesel generator (DG) sets with rated capacity up to 1000 KVA, manufactured on or after the 1st July, 2003 shall be 75 dB (A) at 1 meter from the enclosure surface The diesel generator sets should be provided with integral acoustic enclosure at the manufacturing stage itself The implementation of noise limit for these diesel generator sets shall be regulated as given in paragraph 3 below 2. Noise limit for DG sets not covered by paragraph 1 Noise limits for diesel generator sets not covered by paragraph 1, shall be as follows: 2.1 Noise from DG set shall be controlled by providing an acoustic enclosure or by treating the room acoustically, at the users end 2.2 The acoustic enclosure or acoustic treatment of the room shall be designed for minimum 25 dB (A) insertion loss or for meeting the ambient noise standards, whichever is on the higher side (if the actual ambient noise is on the higher side, it may not be possible to check the performance of the acoustic enclosure/acoustic treatment. Under such circumstances the performance may be checked for noise reduction up to actual ambient noise level, preferably, in the nighttime). The measurement for insertion loss may be done at different points at 0.5m from the acoustic enclosure/room, and then averaged 2.3 The DG set shall be provided with proper exhaust muffler with insertion loss of minimum 25 dB (A) 2.4 these limits shall be regulated by the State Pollution Control Boards and the State Pollution Control Committees 2.5 Guidelines for the manufacturers/users of Diesel Generator sets shall be as under:

01 The manufacturer shall offer to the user a standard acoustic enclosure of 25 dB (A) insertion loss and also a suitable exhaust muffler with insertion loss of 25 dB(A) 02 The user shall make efforts to bring down the noise levels due to the DG set; outside hid premises, within the ambient noise requirements by proper siting and control measures 03 Installation of a DG set must be strictly in compliance with the recommendations of the DG set manufacturer


04 A proper routine and preventive maintenance procedure for the DG set should be set and followed in consultation with the DG set manufacturer which would help prevent noise levels of the DG set from deteriorating with use

3. Limits of noise for DG Sets (Up to 1000 KVA) Manufactured on or after the 1st July 2003 3.1 Applicability

01. These Rules apply to DG sets up to 1000 KVA rated output, manufactures of imported in India, on or after 1st July 2003

02. These rules shall not apply to

a. DG sets manufactures or imported for the purpose of exports outside India; and

b. DG sets intended for the purpose of sample and not for sale in India (Please refer Notification No. G.S.R. 371 (E) dated 17th May, 2002 for details)


Annexure - 12

Estimation of Water Demand

S. No Type of Building Consumption liters/day

1. Factories with bath rooms 45 per head

2. Factories without bath rooms 30 per head

3. Hospital (including laundry):

a) Number of beds not exceeding 100 340 per head

b) Number of beds exceeding 100 450 per head

4. Nurses’ homes and medical quarters 135 per head

5. Hostels 135 per head

6. Hotel (up to 4 star) 180 per head

7. Hotel (5 star and above) 320 per head

8. Offices 45 per head

9. Restaurants 70 per seat

10. Cinemas, concert halls and theaters 15 per seat

11.

Schools

a) Day schools 45 per head

b) Boarding schools 135 per head

In addition, water demand of visitors to these building is considered as 15 LPCD

Source: National Building Code of India, 2005


Annexure - 13 Area Requirements for Parking in Different Types of Cities

Sl. No Occupancy

One Car Parking Space for Every

Population less than

50,000

Population between 50,000 to 2,00,000

Population between

2,00,000 to 10,00,000

Population between

10,00,000 to 50,00,000

Population above

50,00,000

(1) (2) (3) (4) (5) (6) (7)

1

a) Residential ---- ---- 2 tenements having built-up area 101 to 200 m2

1 tenement of 100 m2 built up area

1 tenement of 75 m2 built up area

b) Lodging establishments, tourist homes and hotels, with lodging accommodation

12 guest rooms 8 guest rooms

4 guest rooms

3 guest rooms 2 guest rooms

2 Educational

70 m2 area or fraction thereof of the administrative office area and public service areas



3 Institutional (Medical)

20 beds (Private)

15 beds (Private)

10 beds (Private)

5 beds (Private)

2 beds (Private)

30 beds (Public)

25 beds (Public)

15 beds (Public)

10 beds (Public) 5 beds (Public)

4

a) Assembly Halls, Cinema Theatres

20 seats 80 seats 25 seats 15 seats 10 seats

b) Restaurants 60 seats 40 seats 20 seats 10 seats 5 seats c) Marriage Halls, Community Halls

600 m2 plot area

400 m2 plot area

200 m2 plot area

50 m2 plot area 25 m2 plot area

d) Stadia and Exhibition Center

240 Seats 160 seats 50 seats 30 seats 20 seats

5

a) Business Offices and Firms for Private Business

300 m2 area or fraction thereof





b) Public or semi-public Offices






6 Mercantile (See Note 2)






7 Industrial 400 m2 area or

fraction thereof 300 m2 area or fraction thereof




8 Storage ---- ---- 500 m2 area

or fraction thereof



Source: National Building Code of India, 2005


Annexure - 14 BIS Code of Practices

S.

No BIS Code Description

Cyclone/Wind Storm Protection

01. IS: 875 (3)-1987 Code of Practice for Design Loads (other than Earthquake) for Buildings and Structures, Part 3, Wind Loads

Earthquake Protection

02. IS: 1893-2002 Criteria for Earthquake Resistant Design of Structures (Fifth Revision)

03. IS: 13920-1993 Ductile Detailing of Reinforced Concrete Structures subjected to Seismic Forces – Code of Practice

04. IS: 4326-1993 Earthquake Resistant Design and Construction of Buildings – Code of Practice (Second Revision)

05. IS: 13828-1993 Improving Earthquake Resistance of Low Strength Masonry Buildings – Guidelines

06. IS: 13827-1993 Improving Earthquake Resistance of Earthen Buildings – Guidelines

07. IS: 13935-1993 Repair and Seismic Strengthening of Buildings - Guidelines Protection of Landslide Hazard

08. IS: 14458 (Part 1): 1998

Guidelines for retaining wall for hill area: Part I Selection of type of wall

09. IS: 14458 (Part 2): 1997

Guidelines for retaining wall for hill area: Part 2 Design of retaining / Breast walls

10. IS: 14458 (Part 3): 1998

Guidelines for retaining wall for hill area: Part 3 Construction of dry stone walls

11. IS: 14496 (Part 2): 1998

Guidelines for preparation of landslide – Hazard zonation maps in mountainous terrains: Part 2 Macro-zonation.

Note: 1: Whenever an Indian Standard including those referred in the National Building Code or the National Building Code is referred, the latest revision of the same shall be followed except specific criteria, if any, mentioned above against that code. 2. Codal Provisions/Guidelines Pertaining to Protection for Cyclone or Landslide Hazard cam be omitted whenever not applicable


Annexure - 15 Rain Water Harvesting Structures

Rainwater available from rooftops of buildings, paved and unpaved areas goes waste. This water can be recharged to aquifer and can be utilized gainfully at the time of need. The rainwater harvesting system needs to be designed in a way that it does not occupy large space for collection and recharge system. A few techniques of roof top rainwater harvesting in urban areas are described below. Roof Top Rain Water Harvesting Through Recharge Pit • In alluvial areas where permeable rocks are exposed on the land surface or at very

shallow depth, roof top rainwater harvesting can be done through recharge pits. • The technique is suitable for buildings having a roof area of 100 sq.m. and are

constructed for recharging the shallow aquifers. • Recharge Pits may be of any shape and size and are generally constructed 1.0 to 2.0 m.

wide and 2.0 to 3.0 deep, which are back filled with boulders (5 - 20 cm), gravels (5 – 10 mm) and coarse sand (1.5 - 2.0 mm) in graded form. Boulders at the bottom, gravels in between and coarse sand at the top so that the silt content that will come with runoff will be deposited on the top of the coarse sand layer and can easily be removed. For smaller roof area, pit may be filled with broken bricks/ cobbles.

• A mesh should be provided at the roof so that leaves or any other solid waste / debris is prevented from entering the pit and a desilting /collection chamber may also be provided at the ground to arrest the flow of finer particles to the recharge pit.

• The top layer of sand should be cleaned periodically to maintain the recharge rate. • By-pass arrangement be provided before the collection chamber to reject the first

showers.


Roof Top Rain Water Harvesting Through Recharge Trench • Recharge trenches are suitable for buildings having roof area of 200-300 sq. m. and

where a permeable stratum is available at shallow depths • Trench may be 0.5 to 1.0 m wide, 1.0 to 1.5 m deep and 10 to 20 m. long depending upon

availability of water to be recharge • These are back filled with boulders (5-20cm), gravel (5-10 mm) and coarse sand (1.5-2.0

mm) in graded form – boulders at the bottom, gravel in between and coarse sand at the top so that the silt content that will come with runoff will be coarse sand at the top of the sand layer and can easily be removed

• A mesh should be provided at the roof so that leaves or any other solid waste/debris is prevented from entering the trenches and a desilting/collection chamber may also be provided on ground to arrest the flow of finer particles to the trench

• By-pass arrangement be provided before the collection chamber to reject the first showers

• The top layer of sand should be cleaned periodically to maintain the recharge rate


Roof Top Rain Water Harvesting Through Existing Tube wells • In areas where the shallow aquifers have dried up and existing tube wells are tapping

deeper aquifer, roof to rain water harvesting through existing tube well can be adopted to recharge the deeper aquifers

• PVC pipes of 10 cm dia are connected to roof drains to collect rainwater. The first roof runoff is let off through the bottom of drainpipe. After closing the bottom pipe, the rainwater of subsequent rain showers is taken through a T to an online PVC filter. The filter may be provided before water enters the tube wells. The filter is 1 –1.2 m. in length and is made up of PVC pipe. It’s diameter should vary depending on the area of roof, 15 cm if roof area is less than 150 sq m and 20 cm if the roof area is more. The filter is provided with a reducer of 6.25 cm on both the sides. Filter is divided into three chambers by PVC screens so that filter material is not mixed up. The first chamber is filled up with gravel (6-10mm), middle chamber with pebbles (12-20 mm) and last chamber with bigger pebbles (20-40 mm)

• If the roof area is more, a filter pit may be provided. Rainwater from roofs is taken to collection/desilting chambers located on ground. These collection chambers are interconnected as well as connected to the filter pit through pipes having a slop of 1:15. The filter pit may vary in shape and size depending upon available runoff and are back-filled with graded material, boulder at the bottom, gravel in the middle and sand at the top with varying thickness (0.30- 0.50m) and may be separated by screen. The pit is divided into two chambers, filter material in one chamber and other chamber is kept empty to accommodate excess filtered water and to monitor the quality of filtered water. A connecting pipe with recharge well is provided at the bottom of the pit for recharging of filtered water through well


Roof Top Rain Water Harvesting Through Trench With Recharge Well • In areas where the surface soil is impervious and large quantities of roof water or surface

runoff is available within a very short period of heavy rainfall, the use of trench/ pits is made to store the water in a filter media and subsequently recharge to ground water through specially constructed recharge wells

• This techniques is ideally suited for area where permeable horizon is within 3m below ground level

• Recharge well of 100-300 diameter is constructed to a depth of at least 3.0 to 5.0 m below the water level. Based on the lithology of the area well assembly is designed with slotted pipe against the shallow and deeper aquifer

• A lateral trench of 1.5-to 3.0 m width and 10 to 30 m length, depending upon the availability of water is constructed with the recharge well in the centre

• The number of recharge wells in the trench can be decided on the basis of water availability and local vertical permeability of the rocks

• The trench is backfilled with boulders, gravels and coarse sand to act as a filter media for the recharge wells

• If the aquifer is available at greater depth say more than 20 m, a shallow shaft of 2.0 to 5.0 m diameter and 3.0 –5.0 meters deep may be constructed depending upon availability of runoff. Inside the shaft a recharge well of 100-300 mm dia is constructed for recharging the available water to the deeper aquifers. At the bottom of the shaft a filter media is provided to avoid choking of recharge well

(Source: Rainwater Harvesting Techniques to Augment Ground Water - 2003, Central Ground Water Board)


Annexure - 16

Availability of Rain Water Through Roof Top Rain Water Harvesting

Rainfall (mm) 100 200 300 400 500 600 800 1000

Roof Top Area (Sq.m) Harvested Water from Roof Top (Cum) 20 1.6 3.2 4.8 6.4 8 9.6 12.8 16 30 2.4 4.8 7.2 9.6 12 14.4 19.2 24 40 3.2 6.4 9.6 12.8 16 19.2 25.6 32 50 4 8 12 16 20 24 32 40 60 4.8 9.6 14.4 19.2 24 28.8 38.4 48 70 5.6 11.2 16.8 22.4 28 33.6 44.8 56 80 6.4 12.8 19.2 25.6 32 38.4 51.2 64 90 7.2 14.4 21.6 28.8 36 43.2 57.6 72

100 8 16 24 32 40 48 64 80 150 12 24 36 48 60 72 96 120 200 16 32 48 64 80 96 128 160 250 20 40 60 80 100 120 160 200 300 24 48 72 96 120 144 192 240 400 32 64 96 128 160 192 256 320 500 40 80 120 160 200 240 320 400

1000 80 160 240 320 400 480 640 800 2000 160 320 480 640 800 960 1280 1600 3000 240 480 720 960 1200 1440 1920 2400

(Source: Rainwater Harvesting Techniques to Augment Ground Water - 2003, Central Ground Water Board)


Annexure-17 Certain Design Factors – ECBC, User Guide 2009

Opaque Wall Assembly U-Factor and Insulation R-value Requirements Climate zone Hospitals, Hotels, Call Centers

(24 Hours) Other Building Types (Daytime)

Maximum U-factor of the overall assembly

(W/m2. K)

Minimum R-value of insulation alone

(m2. K/W)


(W/m2. K)


(m2. K/W) Composite U-0.440 R-2.10 U-0.440 R-2.10 Hot and Dry U-0.440 R-2.10 U-0.440 R-2.10 Warm and Humid U-0.440 R-2.10 U-0.440 R-2.10 Moderate U-0.440 R-2.10 U-0.440 R-2.10 Cold U-0.369 R-2.20 U-0.352 R-2.35

Vertical Fenestration U-Factor (W/m2. K) and SHGC Requirements WWR ≤ 40% 40% < WWR ≤ 60%

Climate Maximum U-factor Maximum SHGC Maximum SHGC Composite 3.30 0.25 0.20 Hot and Dry 3.30 0.25 0.20 Warm and Humid 3.30 0.25 0.20 Moderate 6.90 0.40 0.30 Cold 3.30 0.51 0.51 Skylight U-Factor and SHGC Requirements

Maximum U-factor Maximum SHGC Climate With Curb w/o Curb 0-2% SRR 2.1-5% SRR Composite 11.24 7.71 0.40 0.25 Hot and Dry 11.24 7.71 0.40 0.25 Warm and Humid 11.24 7.71 0.40 0.25 Moderate 11.24 7.71 0.61 0.4 Cold 11.24 7.71 0.61 0.4 SRR: Skylight roof ratio which is the ratio of the total skylight area of the roof, measured to the outside of the frame, to the gross exterior roof Minimum VLT Requirements

Window Wall Ratio Minimum VLT 0-0.3 0.27

0.31-0.4 0.20 0.41-0.5 0.16 0.51-0.6 0.13

VLT- Visible Light Transmission


Roof Assembly U-factor and Insulation R-Value Requirements Climate zone Hospitals, Hotels, Call Centers

(24 Hours) Daytime use Buildings other Building

Types Maximum U-factor of the overall assembly

(W/m2. K)


(m2. K/W)


(W/m2. K)


(m2. K/W) Composite U-0.261 R-3.5 U-0.409 R-2.1 Hot and Dry U-0.261 R-3.5 U-0.409 R-2.1 Warm and Humid U-0.261 R-3.5 U-0.409 R-2.1 Moderate U-0.409 R-2.1 U-0.409 R-2.1 Cold U-0.261 R-3.5 U-0.409 R-2.1

(Source: Energy Conservation Building Code (ECBC) User Guide, 2009)


Annexure - 18

Energy Saving Potential of Multiple Glazed Windows over Single Glazing (24 hours usage)

Window Type Percentage

Area Specific Energy Demand kWh/m2/a (includes lighting) [Percentage saving as compared to the single glazing]

Warm & Humid

Composite Moderate Cold & Cloudy

Cold & Sunny

Double Glazed 10% 350[7.8] 299[11.7] 139[6.1] 145[3.9] 472[9.6] 20% 385[7.8] 334[11.1] 145[11] 150[4.4] 514[10.9]

Double Low-E with Argon

10% 336[11.5] 286[15.6] 134[9.4] 142[5.9] 428[19.2] 20% 369[11.7] 323[14.1] 137[15.9] 147[6.3] 446[25.6]

Triple Glazed Energy Efficient Windows

10% 322[15.3] 268[20.9] 124[16.2] 140[7.8] 401[24.3] 20% 354[15.3] 307[18.3] 129[20.8] 145[7.6] 431[28.1]

(Source: MoEF Manual on Large Construction Projects)

Energy Saving Potential for Commercial Buildings of Multiple Glazed Windows over Single Glazing

Window Type Percentage saving as compared to the single glazing

Hot & Dry Warm & Humid

Composite Moderate Cold & Cloudy

Cold & Sunny

Double Glazed 15.8 8.1 14.3 6.2 5.7 11.3 Double Low-E with Argon

26.1 12.3 14.7 16.2 6.8 26.9

Triple Glazed Energy Efficient Windows

28.1 16.5 18.6 21.5 8.1 28.7

(Source: Inderjeet Singh 2004/MoEF, EIA Guidance Manual – Building, Construction, Townships and Area Development)


Annexure - 19

(Suggested CTE Application form for Building and Construction Projects) Date

Explanatory Note for Filing the Application Form

From ………………………………………………………………………………………………………………………………………………………………………………………………

To The Member Secretary, Rajasthan State Pollution Control Board, 4, Industrial Area, Jhalana Doongri, Jaipur 302 004 (Through the concerned Regional Officer)

“Occupier” – in relation to factory or premises, means the person who has control over the affairs of the factory or the premises, and includes, in relation to any substance, the person in possession of the substance “Out let”- Any conduit pipe or channel, open or closed, carrying sewage or trade effluent or nay other holding arrangement which causes or is likely to cause pollution “Trade Effluent” – Includes any liquid, gaseous or solid substance, which is discharged from any premises used for carrying on nay industry, operation or process, or treatment and disposal system, other than domestic sewage “Chimney” – Includes nay structure with an opening or outlet from or through which any air pollutant may be emitted “Industrial Plant” – Nay plant used for any industrial or trade purposes and emitting any air pollutant into the atmosphere “Emission” – Any solid or liquid or gaseous substance coming out of any chimney, duct or flue or any other outlet

To be submitted in triplicate


Sir, I/We hereby apply for:

1. Consent To Establish under Section 25/26 of the Water (P & CP) Act 1974 as amended, to discharge or continue to discharge sewage/trade effluent owned by…………….

Yes No

2. Consent To Establish under Section 21 of the Air (P & CP) Act 1981 as amended, to discharge emissions from industrial plant owned by………………………

Yes No

Part A: General Information 01. Name & Address of the occupier:

Phone No: Fax No: Mobile No: E-mail:

02. Name & Location of the project: Survey No/Plot No/Shed No: Village: Tehsil: District: Pin Code:

03. Category and Scale of the industry: a. Red/Orange/Others: b. Large/Medium/Small:

04. Surrounding details (with in 2 Kms) Human settlement Forest/Sanctuary/National Park/Hill Resort/National Monument/Inter state boundaries

Water Bodies – Nallah/Stream/River/Pond/Dam and any other water bodies

05. Whether the project site is located amidst water body or within 200 meters of HFL of any water body?

Yes/No If yes, Name of the water body…...

06. Site details: Total Area in Ha Built up area in Ha Green belt area in Ha Latitude Longitude

07. Boundaries of the unit North/East/West/South

08. Number of employees working in the unit: 09. Capital investment (in lakhs):


10. Capital investment proposed for pollution control (in lakhs):

11. Applicability of EIA Notification

Yes/No. If yes: EC No………Date…………..

12. Applicability of HW (MH&TM) Rules 2008 as amended Applicable/Not applicable 13. Whether the project is required to obtain NOC from

CGWA for extraction of ground water? Yes/No..If yes: NOC No………Date………

14. Whether the industry attracts the provisions of the Water (P & CP) Cess Act, 1977 as amended?

Applicable/Not applicable

15. Capacity of the Project and facilities proposed Facility Details

16. Details of the parking facilities and norms /codes being followed?

17. Details of solid waste generation other than HW, quantity, storage, disposal and re - use

18. Whether the connected load is 500 kW or greater or a contract demand of 600 kVA or greater?

Yes/No

19. Whether the project developer is planning to adopt ECBC, which is at present voluntary adoption?

Yes/No..If yes, pl attach details as Annexure….

20. What level stars of air conditioners are planned (Ref: Energy Labeling Program of BEE – 1 to 5 Star Rating)?

21. Whether project developer is planning to apply for BEE Star Rating of Office Buildings, which is a voluntary at present)

Yes/No

22. Whether, for exterior lighting, a photo sensor or astronomical time switch that is capable of automatically turning off the exterior lighting when daylight is available or the lighting is not required, is planned?

23. Whether for external lighting solar photovoltaic cells or any other renewable energy sources is explored?

24. Whether roof treatment is planned to reduce the load on the cooling system?

25. Furnish a flow diagram of different activities showing waste generated including for captive power generation and de-mineralized water:

Pl attach as Annexure………

Part B: Information Required in Connection with Prevention and Control of Water Pollution 26. Source of water:

Municipal Supply/Well/Tube Well / Canal / River /Others

27. Water consumption per day for the following streams:KLD

Fresh water Re- use water

Cooling, Humidification plant etc,: For domestic purpose


For swimming pool: For gardening/lawns Others (specify)

Total Water requirement: 28. Details of water saving fittings planned. 29. Wastewater generation per day: KLD

Grey water: Black water: From cooling system: From raw water treatment plant: From swimming pool:

Total wastewater generation per day: 30. Characteristics of waste water before and after treatment

(Designed values shall be furnished) If not applicable – Say No If applicable – Attach as Annexure….

31. Whether water meters proposed? Yes/No If yes, location (s) of water meters proposed: Meter 1 at …………………... Meter 2 at …………………...

32. Whether dual plumbing is planned? Yes/No 33. Whether on-site grey water treatment and re-use of

treated grey water is planned? Yes/No If yes – attach as Annexure

34. Whether areas for usage of treated grey water is identified?

Yes/No If yes – please furnish details………………………...

35. Whether on-site ETP for treating black water is planned? Yes/No If yes – attach as Annexure

36. Whether re-use of swimming pool water is planned? Yes/No If yes – please furnish details………………………..

37. Whether proposing to connect to city sewer with STP provision?

Yes/No. If yes, permission obtained from local authority………..

38. Proposed details of water recycle/reuse/conservation measures:

If not applicable – Say No If applicable – attach as Annexure

39. Whether rainwater-harvesting structure is planned? Yes/No If yes – please furnish details………………………..

40. Whether separate energy meter is provided for ETP alone?

Yes/No

41. Mode of disposal of waste water: Outlet description

Mode of disposal


Part C: Information Required in Connection with Prevention and Control of Air Pollution 42. Sources of Air Emissions:

A Name the unit operations causing emission of pollutants – attach additional sheet if required)

---------------- ---------------- Annexure ……… attached Yes/No

B From boilers: Type Capacity Fuel Fuel

quantity Chimney

height from GL

Type of APC

D From Diesel Generator Sets a. No. of DG Sets: b. Capacity of each DG set: c. Height of the stack above DG room: d. Height of the DG room: e. Noise pollution control measures:

i. Acoustic enclosure/acoustic treatment of DG room:

ii. Exhaust muffler: E Fugitive emissions – Sources and Mitigation

Measures If not applicable – Say No If applicable – Attach as Annexure….

43. Characteristics of critical parameters of air emissions before and after APC, as per the designs:

If not applicable – Say No If applicable – Attach as Annexure….

44. Is project likely to cause noise pollution? If not applicable – Say No If applicable – furnish details

45. Is project likely to cause any other pollution? If not applicable – Say No If applicable – furnish details

Part D: Information Related to Hazardous Waste 46. Code No: 47. Whether the unit falls in a critically polluted area as

identified by MoEF? Yes/No

48. Hazardous waste generation A Type of hazardous waste generated as defined

under the rules:

B Quantum of hazardous waste generated (TPD/KLD) Category wise:

C Sources and waste characteristics (also indicate wastes amenable to recycling, re-processing and reuse):


D Mode of storage within the plant, method of disposal and capacity (provide details):

49. Disposal of hazardous waste: Part E: Other Information, in case of expansion/modernization 50. Status of Environmental Clearance and compliance for

the terms and conditions for the existing projecr If not applicable – Say No If applicable – Attach as Annexure….

51. Notices / Directions issued under section 33(A) of the Water Act, 1974 and section 31(A) of the Air Act, 1981 as amended, during last one year, with compliance report

If not applicable – Say No

52. Compliance to the conditions stipulated in the Consent and HW Authorization to the existing activity

Attach as Annexure…

Declaration I/We further declare that the information furnished in the application form, Annexure / Appendices and plans is correct to the best of my / our knowledge I/We hereby submit that in case of change either of the point, or the quantity of discharge/emissions or its quality, a fresh application for Consent shall be made and until such consent is granted, no change shall be made I/We undertake to furnish any other information within one month of its being called by the State Board. Enclosures 1. I/We enclose herewith Bank Draft No ……………………Dated…………………………for Rs……………….(Rs. In words……………………………………) in favor of the Member Secretary, Rajasthan Pollution Control Board, payable under Section 25/26 of the Water Act. 2. I/We enclose herewith Bank Draft No…………dated…………for Rs………….(Rs. In words…………………………) in favor of the Member Secretary, Rajasthan Pollution Control Board, payable under Section 21 of the Air Act. 3. In support of amount paid as fee, document on capital investment on the industry must be enclosed. An application not accompanied with the prescribed fee and support document shall not be entertained by the Board 4. Affidavit in the prescribed proforma 5. Land allotment/ land conversion order 6. Site map 7. Document in support of authorizing the person to sign the application 8. Different Annexures duly giving numbers as mentioned in the application

Yours faithfully, Signature of the Applicant……………………. Name……………………………………………. Designation……………………………………..

Office Seal


Annexure - 20

Consent Fee Structure with Reference to Submission Time of CTO Application

Consent To Operate (First Time) S.No Time of making an application to the state Board for

Consent to Operate Consent Fee

1 If made, at least four months before the expiry of period of consent to establish

Fee as per Schedule IV

2 I If made, between four to three months, before the expiry of period of consent to establish

With additional fee of 25% of the fee prescribed in Schedule IV

3 If made, between three to two months before the expiry of period of consent to establish


4 If made, between two to one month, before the expiry of period of consent to establish


5 If made, with in one months, before the expiry of period of consent to establish

With additional fee of 100% (double the amount) of the fee prescribed in Schedule IV

Consent To Operate (Renewal)

S.No Time of making an application to the state Board for

Consent to Operate Consent Fee

1 If made, at least four months before the expiry of period of consent to operate

Fee as per Schedule IV

2 I If made, between four to three months, before the expiry of period of consent to operate


3 If made, between three to two months before the expiry of period of consent to operate


4 If made, between two to one month, before the expiry of period of consent to operate


5 If made, with in one months, before the expiry of period of consent to operate

With additional fee of 100% (double the amount) of the fee prescribed in Schedule IV

Ref: G.S.R 38 Dated 24 June 2010 of Department of Environment, Govt.of Rajasthan


Annexure - 21 Consent To Operate Fee (Schedule-IV) - Water Act

S. No. Capital investment (in Rs)

For Consent To Operate

Appendix A Appendix B Other than Appendix A and B

For 1 Year

For 3 Years

For 1 Year For 5 Years


1 Upto 5 Lacs 1400 4000 1200 5000 1000 90002 More than 5 lacs upto 10 lacs 2100 6000 1800 8000 1500 135003 More than 10 lacs upto 25 lacs 2800 8000 2400 11000 2000 180004 More than 25 lacs upto 50 lacs 4000 11000 3500 16000 3000 270005 More than 50 lacs upto 1 crore 4800 13000 4200 19000 3600 320006 More than 1 crore upto 5

crores 6400 17000 5600 25000 4800 43000

7 More than 5 crores upto 10 crores 8000 22000 7000 32000 6000 54000








15 Above 1000 crores 61000 166000 53000 245000 42000 378000Ref: Notification dated 10th December 2010, DoE, Govt of Rajasthan

1. The categorization of the projects is as Notified by the DOE, Government of Rajasthan vide dated 10th December, 2010 2. All industries/process/projects/activities generating HW as defined under the HW (MH&TM) Rules 2008 and requiring authorization thereunder, the application for consent shall be accompanied with fee equal to one and half times of the amount of fee prescribed under the schedule, other than the HW covered under category 5.1 of schedule 1 of HW (MH&TM) Rules 2008 if the quantity of waste /used /spent oil is < 5 KL per annum 3. The Concessional fee for consent to operate shall only be applicable for the period as specified in the schedule and no concessional fee is applicable for intervening period


Annexure - 22 Consent To Operate Fee (Schedule-IV) - Air Act

S. No. Capital investment (in Rs)

For Consent To Operate

Appendix A Appendix B Other than Appendix A & B

For 1 Year

For 3 Years For 1 Year For 5 Years


1 Upto 5 Lacs 1400 4000 1200 5000 1000 90002 More than 5 lacs upto 10 lacs 2100 6000 1800 8000 1500 135003 More than 10 lacs upto 25 lacs 2800 8000 2400 11000 2000 180004 More than 25 lacs upto 50 lacs 4000 11000 3500 16000 3000 270005 More than 50 lacs upto 1

crore 4800 13000 4200 19000 3600 32000

6 More than 1 crore upto 5 crores 6400 17000 5600 25000 4800 43000









15 Above 1000 crores 61000 166000 53000 245000 42000 378000Ref: Notification dated 10th December 2010, DoE, Govt of Rajasthan

1. The categorization of the projects is as Notified by the DOE, Government of Rajasthan vide dated 10th December, 2010 2. All industries/process/projects/activities generating HW as defined under the HW (MH&TM) Rules 2008 and requiring authorization thereunder, the application for consent shall be accompanied with fee equal to one and half times of the amount of fee prescribed under the schedule, other than the HW covered under category 5.1 of schedule 1 of HW (MH&TM) Rules 2008 if the quantity of waste /used /spent oil is < 5 KL per annum 3. The Concessional fee for consent to operate shall only be applicable for the period as specified in the schedule and no concessional fee is applicable for intervening period

buidling&construction _fianl reort _sep2011

Documents

environmental aspects

environmental acts

environmental norms

guidance manual sector

national environmental

legal requirements water

legal requirements e

design construction