building electronics with surface mount technology james jefferson jarvis kb0thn aprs world, llc...

17
Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC [email protected] www.aprsworld.com

Upload: bertram-rose

Post on 23-Dec-2015

220 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Building Electronics with Surface Mount Technology

James Jefferson Jarvis KB0THNAPRS World, [email protected]

www.aprsworld.com

Page 2: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Presentation OutlineWhat is Surface Mount Technology?Why is it used?How do I do it?What do I need?

Page 3: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

What is Surface Mount Technology?

There are two type of components

Through hole partsUse holes through circuit board that components are soldered in to

Surface mount partsSoldered on top of circuit board

Page 4: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

SMT PartsAll kinds of parts are available in surface mount

Integrated circuitsCapacitors, resistors, inductorsLEDsConnectors

Page 5: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Why is it used?SMT is smaller, faster, cheaperMost new and cool products are only available in surface mount packages

Accelerometers smaller than your fingernailComputers on a chipRadios on a chip!

Page 6: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

How do I do it?Watch the demonstration and learn

Page 7: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Recommended Soldering Iron

Workable QualityRadio Shack 15 watt soldering iron

Radio Shack P/N 64-2051$9

Only one tip$1

Page 8: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Recommended Soldering Iron

Good QualityWeller WLC100

Jameco P/N 146596$49

ST1 1/16” conical tip$5

Page 9: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Recommended Soldering Iron

Excellent QualityWeller WESD51

Digi-Key P/N WESD51-ND $160

ETS tip$5

Page 10: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Recommended ToolsXcelite 170M side cutters

$6

Small needle nose pliers

Page 11: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Recommended SolderKester No Clean Solder – 28 AWG (tiny)

Digi-Key P/N KE1407-ND$18This is a half pound of 0.015” diameter solder so it will last you a lifetime

Page 12: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Recommended FluxKester #951 Low-Solids, No-Clean, Pen

Digi-Key P/N KE1804-ND$3.70

Rosin, Mildly Activated flux is okay but will leave a big sticky mess on your board

Liquid and aerosol flux remover can be used, but it is nasty

If water soluble flux is used it *MUST* be washed off the board when done

Page 13: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Recommended Desoldering Braid

Techspray Prowick Size #25’ long, 0.055” wideAbout $4

Page 14: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Recommended VicePanavise Jr

Digi-Key P/N 201PV-ND$24

Page 15: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Prototyping BoardsSurfboards!

Available from Digi-KeySpecifications at http://www.capitaladvanced.com/

Page 16: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Where to buy this stuffDigi-Key, Thief River Falls, Minnesota

www.digikey.com1-800-DIGIKEY

Jameco, Belmont, Californiawww.jameco.com1-800-831-4242

Radio Shackwww.radioshack.com

Spark Fun Electronicswww.sparkfun.com1-303-284-0979

Page 17: Building Electronics with Surface Mount Technology James Jefferson Jarvis KB0THN APRS World, LLC jj@aprsworld.net

Try it yourself…After the meeting we can build a simple circuit board with surface mount partsIt’s a $4 practice board … and if it works you get a free RS-232 TTL converter

It has one 16 pin chip, five capacitors, and a connector