Cabinet Setup Guidefor the 40 U CabinetP/N 014003099REV A01

Tools Required

PhillipsScrewdriver

FlatScrewdriver

14-mm (9/16-in.)Socket Wrench

AdjustableWrench

Notice

Copyright 2002 EMC Corporation. All rights reserved.Printed February, 2002

EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without notice.

THE INFORMATION IN THIS PUBLICATION IS PROVIDED "AS IS." EMC CORPORATION MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WITH RESPECT TO THE INFORMATION IN THIS PUBLICATION, AND SPECIFICALLY DISCLAIMS IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Use, copying, and distribution of any EMC software described in this publication requires an applicable software license.

Trademark InformationEMC2, EMC, MOSAIC:2000, CLARiiON, Navisphere, and Symmetrix are registered trademarks and EMC Enterprise Storage, The Enterprise Storage Company, The EMC Effect, Connectrix, EDM, SDMS, SRDF, Timefinder, PowerPath, InfoMover, FarPoint, EMC Enterprise Storage Network, EMC Enterprise Storage Specialist, EMC Storage Logic, Universal Data Tone, E-Infostructure, Access Logix, MirrorView, SnapView, and Celerra are trademarks of EMC Corporation.

All other trademarks used herein are the property of their respective owners.

1 Step 1Remove the ramp and shipping material from the pallet

IMPORTANT The illustrations in this guide are examples only. Depending on what you ordered, your configuration may look somewhat different from what is shown here.

1. Remove the plastic covering from the cabinet.

2. Remove the ramp bumper.

3. To release the ramp from the pallet, grasp the ramp, pull it straight back toward you, then pull it straight up to free it from the screws.

EMC2134

Rotated 90

Rear

2 Step 2Attach the unloading ramp

1. Insert the ramp brackets into the pallet notches in the rear of the pallet.

EMC2135

Rear

3 Step 3Remove the cabinet shipping brackets

1. At the rear of the cabinet, open the door and remove the rear shipping bracket.

2. At the front of the cabinet, remove the bottom cap and the front shipping bracket.

NOTE If your cabinet has a front door, open the door to access the bottom cap and front shipping bracket.

EMC2136

DoorLatch

Rear14-mm 9/16-in.)Socket Wrench

14-mm (9/16-in.)Socket Wrench

Front

4 Step 4Roll the cabinet down the ramp

IMPORTANT Make certain the leveling feet are secured in the UP position before moving the cabinet. Secured feet allow the cabinet to roll off the ramp and into position. If you need to adjust the leveling feet, use an adjustable wrench and turn the feet clockwise to raise them to the UP position.

The cabinet is heavy. Make certain you have sufficient help and secure footing before rolling the cabinet onto the ramp

EMC2137

LevelingFeet

Rear

Rails

!

EMC2148

Rear

Front

5 Step 5 Position and level the cabinet

EMC2139

Front Rear AdjustableWrench

Step 6Remove the shipping plates

EMC2140

Remove Screws(4)

Pull Out,Lift Up

The shipping plates across the rear of the cabinet provide rigidity during shipping.

RearNote: The rear door is removed for clarity.

LoosenScrews(2)

6 Step 7Verify ac power

1. Verify that all your system components are plugged into the cabinet power distribution unit (PDU). In high-availability configurations, make certain redundant components are attached to separate power sources.

2. Connect the site ac power cord to the PDU ac power cord.

IMPORTANT Refer to the Setup Guide(s) and/or hardware reference in the ACCESSORIES box that shipped with your system to continue with system and component setup.

EMC2141

FrontRear

PowerDistributionUnit(PDU)

Note: The rear door is removed for clarity.

PDUac PowerCord

Siteac PowerCord

7 If you need help

Contact EMC Customer Service by calling:

When you call, please have the following information available:

system/array model number

your site ID, customer name and address, or array serial number

United States: 1-800-782-4362 (SVC-4EMC)Canada: 1-800-543-4782(543-4SVC)

Worldwide: 1-508-497-7901

You can also obtain technical support and assistance by calling your local EMC sales office.

Cabinet Setup Guide for the 40 U CabinetCopyrightStep 1 - Remove the ramp and shipping material from the palletStep 2 - Attach the unloading rampStep 3 - Remove the cabinet shipping bracketsStep 4 - Roll the cabinet down the rampStep 5 - Position and level the cabinetStep 6 - Remove the shipping platesStep 7 - Verify ac powerIf you need help