canon ir1600 2000 2010f series elitec essentials

7/26/2019 Canon IR1600 2000 2010F Series ELITEC Essentials

http://slidepdf.com/reader/full/canon-ir1600-2000-2010f-series-elitec-essentials 1/5

ELITEC Essential Technical Information

ImageRunner 1600 / 2000 / 2010F

Profile: DigitalSpeed:16/20 CPM

Consumables: Item Designation Order Number Yield

Toner 440g. GPR-18 6836A003AA 7,850 @ 6%

Drum 6837A004AA 21,000

Trouble CodesE000 Fuser did not heat up.E001 Fuser temperature too high.E002 Fuser temperature not rising at correct pace.E003 Fuser temperature drops.E004 Fuser temperature problem.E010 Drive error.E100 Laser related problem/Drum unit worn/not installed .SEE NOTE *E246 Reading from/to soft counter memory not achieved. SEE NOTE**E500 Finisher main board or comm. with copier.E514 Stack delivery motor or sensor.E530 Rear jogging plate motor or sensor.E531 Finisher Stapler motor, sensor.

E537 Front jogging plate motor M3, Front aligning plate home sensor.E551 Finisher fan.E577 Finisher delivery motor or sensor.E580 Finisher stack tray upper limit sensor or motor problem.E583 Finisher tray aux plate motor or sensor.E585 Finisher stack handling motor or sensor.E805 Fan .E719 Communication problem:image processor/card reader.

redRESET Shut power OFF/ON, service mode 7:4:pr inter reset:YES =(*)E355 Not listed. Reset with menu 12 see below.



Drum removal Open front door and unlock developer unit, slide out side cover, lift drum unit out.

Developer unit removal After removing drum unit (as described above), remove toner cartridge and remove bypassassembly, unlock DV unit by turning handle, remove 2 screws in front holding shaft guide, andremove it.Pull the DV unit out from the left side by the handles-this is a mono component machine there is no developer calibration needed.

Waste TonerStored inside drum unit, when full WASTE TONER FULL will display and drum unit should beemptied or replaced.

SERVICE MODE

ACCESS: Select USER MODE by pressing ADDITIONAL FUNCTION keyPress ID key (#) on user mode screenSelect menu item using cursor keyPress OK key. Select an item with cursor keyPress OK key enter new values with number keys, press OK to lock inPress STOP key to end service mode.

DC Controller VR´s

VR101: lead edge registration adjustment.

VR401: high voltage. factory use only.

VR402: Toner level detect. factory use only.

VR403: Toner level detect. factory use only.

SW101: test print.

Service menus 1: SSSW (service softswitches): do not touch any except 33.Softswitch 33:

0: 1 to count as large size paper.1: 1 for serial number on counter screen.2: up to 7: not used.

2: Menu: not used.3:Numerical parameters: change only 56-61 this has to do with counter check screen. If 0 notcounter indicated. 56-61 are to select count for counters 1-6.100s:total.200s:copy.

300s: print.500s: scan.700s: received print.800s: report print.4.not used.5:Type:when setting country, others will change automatically.6: Scanner: do not change. 1 Bit switch: do not change 2 Slice: do not change 3 Gamma: do not change 4 Numeric: do not change 5 LUT 1 fno:do not change 6 LUT 2 adj: do not change

7 CCD: Bit purpose: default setting0 to 17: don’t touch



18: contact start adjust ADF read:47019: shading position adjust:9020: CS Wobble correction:4021: Main scan image read start adjust (book):12822: Main scan image read start adjust (ADF):12823: subscan read start adjust (book):145

24: subscan read start adjust (ADF):23525: subscan read end position correct (copy):5226-28:not used29: Main scan image read ratio correct (book):1630: Main scan image read ratio correct (ADF):1631: Subscan image ratio correct (book):1632: Subscan image read ratio correct(ADF):1634: ADF feed motor speed adjustment:508: Model: turn on/off original detect. Type A original size detect not used, type B original

will be used.7:Printer:

2: Numeric parameters:01-03 not used.04:lead edge margin (30 is default)

05:Trail edge margin (70 is default)3: Print count.4: Prin ter reset: YES=(*)to clear fuser error. NO=(#).

6: CST: Cassette size configuration [ not in Intravia’s guide]USER MODE+ # using cursor keys select #7 PRINTER+ OK select # 6 CST + OKSee table for different sizes- choose with cursor key, enter new value with numeric keys + OKPower OFF/ON.Check correct programming running a copy and watching the panel, it must show the correct symbolFor the size chosen (according to table), copy must exit without warning alarm.

Available Paper Size Holeposition

Paper SizeGroup

SetValue

ScreenDisplay

Government LTR LTR U1 31 LTR

Foolscap LGL U2 24 FLSCOficio LGL U2 26 OFI

Ecuador Oficio LGL U2 27 OFI

Bolivia Oficio B4 U2 28 OFI

Argentina Oficio LGL U2 36 OFI

Argentina LGL LGL U2 33 LGL

Mex Ofic io LGL U2 37 OFI

Government LGL LGL U3 34 LGL

Government LTR R LTR R U3 32 LTR R

Folio LGL U3 35 Folio

Australia Foolscap LGL U3 25 FLSC

Argentina LTR B5 LTR 29 LTR

Argentina LTR R A4 LTR 29 LTR R

8:PDL:PDL-lips MENU:NOT USED.PDL-PCL menu: printer related.

9:Counter.Total:Service 1 is total counter 1.Service 2 is total counter 2.TTL is total counter.Copy is total copy count.PDL-PRT is PDL print count.FAX-PRT is fax received (not used).RPT-PRT is report count.SCAN is scan count.PickUp:



C1: cassette 1.C2: cassette 2.C3: cassette 3.C4: cassette 4.MF: manual feeder: (bypass).Feeder (presumably ADF, but manual does not say).

Jam related: same displays as Pickup.Miscellaneous.DRBL-1 (durables)FX-UNIT is fuser count.TR-ROLL is transfer roller count.DV-UNT-C is developer unit count.M-SP-RL is bypass count.M-SP-P-D is bypass separator pad count.DRBL-2 (Accesory durables)FIN-STPR is finisher count.

10: Report.Service & System (not used).

Service data:1-7,13,start data.System dump: not used.Key History: last 1800 key presses.Batch log: not used.Counter: Maintenance/parts counters.Jam/error log: jam /error alarms.Print spec: type settings, memory size, ROM indications, adjustment data.

11:Download firmware:ROM DIMM and CPU on image processor board. ROM on finisher DC controller.If USB driver not installed on computer, go to ADD NEW HARDWARE WIZARD and select driver,When done click FINISH. Restart computer, install the firmware to the service tool. Install (mayneed factory manual or firmware may have instructions).

Download: shut power, remove rear cover and connect USB connector J203 to imageprocessorBoard and PC, disconnect USB from NIC if used, turn ON PC, click download/upload.On machine press USER MODE and then press # to start service mode, select #11DOWNLOADWith >< keys, click OK on computer, select IR1600 SYSTEM on PC screen, click CONNECT onPCClick OK. Click OK again when done.

Click SYSTEM SOFTWARE DOWNLOAD select from list on screen. Click START, machine willstart At end of download, when ADD NEW HARDWARE displays click CANCEL, shut machine power.

Shut PC, disconnect USB cable, connect USB back to NIC if used, turn ON machine,Press USER MODE and # to start service mode, using <> keys select #13 ROM and press OK.Using <> keys check version in MAIN. Go to service mode 12 and select CLEAR >ALLenter #5 type press OK to lock in. Press CLEAR to go back to copy mode.

12:Clear:Press CLEAR key to clear the count.TEL/USER data: not used.User data initializeService switches 1-7 initialize.Service data: not used.Report: Activity (not used) jam, error alarmCounter: Print Clear.

ERR (E355 Clear)



All clear except counter.13:ROM.

Main 1:Image processor board.Main 2:Image processor board.ECONT: DC controller board.FIN: finisher.

PDL: PCL printer board.NIC: Network Interface Board.NCR: card Reader.

14:CS set to shipping position.Test modes: press USER MODE press #, select SERVICE MODE select TEST MODE with <>keysPress OK, press STOP and then CLEAR to end test mode.1:D-RAM test.2:CCD test. Correct variation in sensitivity of CCD sells.3:PRINT test:8 different test patterns.4:FACULTY test:(Note it might be 6 instead of 4) test various switches, sensors, ADF functions

speakers, etc.).5:BOOK test: test read transmission LEDs.

ELITEC Essential Technical Info

Compiled by Jaime Rios for ELITEC/STARPR1NThttp://starpr1nt.tripod.com

[email protected]

canon ir1600 2000 2010f series elitec essentials

Documents