canon powershot sx100is

SAFETY PRECAUTIONS

The following precautions should be observed when servicing.

1. Since many parts in the unit have special safety-related characteristics, always use genuine CANON replacement parts.

Especially critical parts in the power circuit block should not be replaced with other makes.

Critical parts are marked with ! in the schematic diagrams.

2. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged

by the short circuit.

3. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.

4. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

4-1 Leakage Current Cold Check

1) Unplug the AC cord and connect a jumper between the two prongs on the plug.

2) Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part

on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to

the chassis, the reading should be between 1MΩ and 5.2MΩ. When the exposed metal does not have a return path to the

chassis, the reading must be ∞.

4-2 Leakage Current Hot Check

1) Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2) Connect a 1.5KΩ 10 watt resistor, paralleled by 0.15µF capacitor, between each exposed metallic parts on the unit and a

good earth ground such as a water pipe, as shown in the figure below.

3) Use an AC voltmeter, with 1000Ω/volt or more sensitivity, to measure the potential across the resistor.

4) Check all exposed metallic parts of the cover (Cable connection, Handle bracket, metallic cabinet.

Screwheads, Metallic overlays, etc), and measure the voltage at each point.

5) Reverse the AC plug in the AC outlet and repeat each of the above measurements.

6) The potential at any point should not exceed 0.75V RMS.

A leakage current tester (FLUKE MODEL : 8000A equivalent) may be used to make the hot checks.

Leakage current must not exceed 0.5 milliamp.

In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and corrective action must

be taken before returning the instrument to the customer.

Water pipe

(Earth Ground)

1.5KΩ

0.15µF

Test allexposedmetal parts

Figure. 1 Leakage Current Hot CheckAC OUTLET

AC VOLTMETER

DEVICEUNDERTEST

Trademarks:Canon Inc.'s trademark, logos, product names, service marks and those trademark, logos, product names,service marks licensed to Canon Inc. by any of its affiliate or subsidiary are registered or unregisteredmarks of Canon Inc. or such affiliate or subsidiary in Japan and/or other countries.Adobe, the Adobe logo, Acrobat, the Acrobat logo and Reader are either registered trademarks or trade-marks of Adobe Systems Incorporated in the United States of America and/or other countries.All other trademarks, product names, service marks are generally either registered or unregistered marksof their respective owners.

Copyright:All copyrights in the content of this Service Manual are owned or controlled by Canon Inc. You are notpermitted to copy, reproduce, download, modify, adapt or translate in any way the content of this ServiceManual for any purpose other than the purpose contemplated herein without prior written consent ofCanon Inc.

R2: CONFIDENTIAL

GENERAL DESCRIPTIONOF PRODUCT

CONTENTS1 Overview

1-1 Summary of Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1-2 Development Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1-3 Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1-4 Comparison of Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Exterior

2-1 Exterior Photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2-2 6-view Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2-3 Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3 Specifications

3-1 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3-2 System Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3-3 Shooting/Setting Features List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3-4 Direct Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3-5 Playback Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3-6 List of Accessory and Its Compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4 Accessory Specifications

4-1 Main Unchanged Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

1

1 Overview

1-1 Summary of Main FeaturesText highlighted in red: New features introduced with the PowerShot SX100 IS, Text highlighted in blue: Differences from the PowerShot A710 IS

!DIGIC III imaging processor provides improved image quality and functionality!High-resolution 8.0-megapixel CCD supports prints up to A3 size! 10x optical zoom lens with lens-shift type image stabilizer significantly reduces camera shake

• 36 – 360 mm (35mm film equivalent), f/2.8 (W) – f/4.3 (T)!High ISO Auto and high ISO-speed 1600 significantly reduce camera shake and subject blur! iSAPS technology enables high-speed AF and high-definition AE/AWB

<Still Images>!Face detection function

• Face Detect AF focuses on the faces in the scene- AF frame can be moved and fixed to specifyed face

• Face Detect AE also evaluates the brightness of faces in the scene when evaluating exposure• Face Detect FE controls the flash output for optimum face brightness during flash photography

High Image Quality

Full Featured and Easy Operation

Shooting Features

A new model in a new category, the PowerShot SX100 IS blends the defining characteristics of the Power-Shot A700 series, such as ease of use and exceptional cost-performance ratio, with those of the PowerShot S series, including a high-performance, high-factor zoom lens for a successful balance of still image and movie shooting.

2

!Selected ISO speed is displayed in 1/3 stop increments on the LCD monitor• ISO speed is displayed when pressing the shutter button halfway while Auto or High ISO Auto is

selected• The raised ISO speed is displayed when using the Auto ISO shift

!AF frame size is selectable between 'Normal' or 'Small'!Auto ISO shift raises the ISO speed to allow a shake free shutter speed!Safety FE reduces the occurrence of highlight blowout during flash photography at close distances!Night Display automatically brightens images on the LCD monitor during sunset and evening shooting!Safety zoom enables active use of digital zoom ranges where image quality is not reduced!AF mode allows selection of Single (at shooting) or Continuous (always on) AF!Continuous shooting AF takes continuous shots while focusing on a moving subject!Digital tele-converter easily allows telephoto photography as if a tele-converter is attached!Program shift allows changing the shutter speed and aperture value combinations while keeping the opti-

mum exposure!Safety shift automatically shifts the shutter speed or aperture value to obtain the optimum exposure! Image Inspection Tool checks image focus during rec. review

• Improved operability

<Movies>!Long Play (LP) mode allows longer recording times at same recording pixels and frame rate

<Still Images, Movies>! 19 shooting modes, including scene and movie modes

• Night Snapshot and Kids & Pets moved from scene modes to become independent shooting modes on the shooting mode dial

!Manual focus does not have the time lag experienced in AF operation!Safety MF controls fine focus tuning when pressing the shutter button halfway during manual focus pho-

tography!My Colors enables customization of the colors in the scene during shooting (Limited type)!Quick-bright LCD maximizes brightness when the LCD monitor is hard to see, such as in bright sunlight

or other strong light sources!Computer-controlled shooting enables shooting operation from a computer!The Intelligent Orientation Sensor automatically detects camera orientation (horizontal and vertical) dur-

ing shooting

<Still Images>!Auto red-eye correction uses the face detection function to automatically correct red-eye that occurred

during flash photography• Red-eye frame can be removed

!Recorded images can be resized to 1600 x 1200 pixels, 640 x 480 pixels, and 320 x 240 pixels! Image Inspection Tool enables confirmation of the focus for playback images!The Jump function enables instant jumping to and playback of specific images based on keywords!Histogram indicates the brightness distribution of the image being shot!Transition adds fade-in and fade-out effects when switching between playback images

Playback Features

3

<Still Images, Movies>!Resume Playback starts playback from last viewed image (still image) or frame (movie)

!PictBridge for superior versatility and Canon Direct Print to maximize the functions of Canon printers

!Face Selector button provides better operability on face detection function!Round number of total pixels are displayed together with the number of recording pixels (horizontal pix-

els x vertical pixels)!Playback button switches between shooting mode and playback mode by one-push operation!Transition to shooting mode by pressing the shutter button halfway during playback mode! ISO speed can be selected quickly for each scene by using the ISO button selector!Control Dial enabling easy control of a various functions!Shortcuts can be assigned to the Print/Share button for improved ease of operation!Shutter speed and f/number are displayed on the LCD monitor when pressing the shutter button halfway

during shooting!Selectable options display on the LCD monitor when setting shooting parameters

!Large size (2.5-inch) LCD monitor with high-resolution (approx. 172,000 pixels) and wide viewing angle!Supports SDHC memory card and HC MMCplus card for high-volume shooting (both still images and

movies)!UI display available in 25 languages*

* The models for Japanese market available with 2 languages (Japanese and English) only

!By employing curved lines within an orthodox form, the PowerShot SX100 IS achieves an innovative design that embodies a new category of digital camera

Printing Features

Operability

Others

Design

4

1-2 Development ObjectivesCompact cameras featuring high-powered zoom from 7x to 10x have been introduced by competing manu-facturers and are gaining market share.In a body that is approximately the size of the PowerShot A series, the PowerShot SX100 IS features a 10xzoom lens with lens-shift type image stabilizer. The camera was developed to offer easy shooting coveringthe full range from wide angle to telephoto. Core-spec features such as 8-megapixel CCD and DIGIC III arecomplemented by Face Detect AF/AE/FE, red-eye correction, Auto ISO shift, and many other attractivefunctions. Thanks to the addition of a Face Selector button, the face detection AF function has become eveneasier to use.The PowerShot SX100 IS merges the concepts of the PowerShot G series and A series into a new series thatis bound to meet the new demands of a market.

1-3 DesignConceptCompared to the PowerShot S5 IS which also has a high-power zoom lens, the new model has beendesigned to offer user friendly form as a compact model that blends with everyday life.

Shape highlightsContinuously flowing rounded form seamlessly joins the front and rear sides. This form concept alsoextends to the grip section and results in a simple shape without brusqueness that still provides secureholding characteristics.The top section has the pop-up flash common to all high-power zoom models, with a sculpture-like cutshape that emphasizes the high power zoom capability.The layout of the operation controls is simple with eliminating complex impression that makes user-friendly and approachable appearance also to novice users.

Color highlightsTwo color variations are available, one in stately black that evokes the PowerShot S5 IS and one in lightsilver giving a light and airy feeling. The light silver version creates a transparent new image with atwo-tone finish employing a combination of matte and glossy coated parts.

Flash height has been kept low to emphasize body compactness.

Body coloring is stately black or light silver with subdued contrast

Controls are highly approachable and user friendly

Overall shape is smooth and gives a sense of ease

Sculpture-like character emphasizes flash section as in PowerShot S series

Metal parts in lens barrel section emphasize high-power zoom as in PowerShot S series

5

1-4 Comparison of Main Features• Highlighted table items indicate changes from the PowerShot A710 IS. Text in red shows changes.

Conditions may apply depending on items (for details, see 3-1 Product Specifications).

PowerShot SX100 IS PowerShot A710 ISImage Sensor (CCD) Camera Effective Pixels Approx. 8.0 million pixels, 1/2.5-inch type Approx. 7.1 million pixels, 1/2.5-inch type

Lens

Focal Length (35mm film equivalent) 10x zoom: 36 (W) – 360 (T) mm 6x zoom: 35 (W) – 210 (T) mm

Focusing Range

Normal 50 cm (1.6 ft.) – infinity (W), 1 m (3.3 ft.) – infinity (T) 55 cm (1.8 ft.) – infinityMacro 1 – 50 cm (0.39 in. – 1.6 ft.) (W) 1 – 55 cm (0.39 in. – 1.8 ft.) (W)Super Macro –

Image Stabilizer (IS) System Lens-shift typeImaging Processor DIGIC III DIGIC IIViewfinder – Real-image optical zoom viewfinder

LCD MonitorType 2.5-inch type, color LCD

(Effective pixels: Approx. 172,000 pixels)2.5-inch type, color LCD (Effective pixels: Approx. 115,000 pixels)

Features Quick-bright LCD –

Focus

Single, continuousAF (Face Detect* / center)* If no face is detected, center 1-point is used. • AF frame can be moved and fixed to specified face.

Manual focus

AiAF (9-point) / AF (1-point*) / Manual focus* Fixed to center / FlexiZone AF

Metering SystemEvaluative*1, Center-weighted average, Spot*2*1 Control to incorporate facial brightness in Face

Detect AF.*2 Fixed to center

Evaluative, Center-weighted average, Spot** Fixed to center / linked to the AF frame

ISO SpeedAuto, High ISO Auto, ISO 80/100/200/400/800/1600 (Standard Output Sensitivity, Recommended Exposure Index)

Auto, High ISO Auto, ISO 80/100/200/400/800 equivalent

White Balance Auto, Day Light, Cloudy, Tungsten, Fluorescent, Fluorescent H, Custom

Auto, Day Light, Cloudy, Tungsten, Fluorescent, Fluorescent H, Underwater, Custom

ShutterType Mechanical shutter and electronic shutterSpeeds 15 – 1/2500 sec. 15 – 1/2000 sec.

ApertureType Iris type

f/number f/2.8 – f/8.0* (W), f/4.3 – f/8.0* (T)* The f/number can be set to f/11 when Auto mode. f/2.8 – f/8.0 (W), f/4.8 – f/8.0 (T)

FlashRange

50 cm – 3.0 m (W), 50 cm – 2.0 m (T) (1.6 – 9.8 ft. (W), 1.6 – 6.6 ft. (T))(ISO speed: Auto)

Normal: 55 cm – 3.5 m (W), 55 cm – 2.5 m (T) (1.8 – 11 ft. (W), 1.8 – 8.2 ft. (T))Macro: 30 – 55 cm (W – M) (12 in. – 1.8 ft. (W – M))(ISO speed: Auto)

Main Features Manual flash output setting (3 levels), flash output compensation, Safety FE

Manual flash output setting (3 levels), flash output compensation, 2nd/1st curtain sync

Sho

otin

g Sp

ecifi

catio

ns Shooting ModesAuto, P, Tv, Av, M, Portrait, Landscape, Night Snapshot, Kids & Pets, Special Scene*, Stitch Assist, Movie* Night Scene, Indoor, Foliage, Snow, Beach,

Fireworks, Aquarium

Auto, P, Tv, Av, M, Portrait, Landscape, Night Scene, Special Scene*, Stitch Assist, Movie

* Night Snapshot, Kids & Pets, Indoor, Foliage, Snow, Beach, Fireworks, Underwater, Color Accent, Color Swap

Digital ZoomStill images / Movies: Approx. 4.0x (up to approx. 40x in combination with the optical zoom)Safety Zoom, Digital tele-converter

Still images / Movies: Approx. 4.0x (up to approx. 24x in combination with the optical zoom)Safety Zoom, Digital tele-converter

Main Features My Colors (Limited type), Auto ISO Shift My Colors

Continuous Shooting Normal: Approx. 1.3 shots/sec., AF: Approx. 0.8 shots/sec.,LV: Approx. 0.8 shots/sec. (Large and Fine) Approx. 1.7 shots/sec., (Large and Fine)

Number of Images Shot (CIPA) Approx. 140 images (alkaline), Approx. 400 images (NiMH) Approx. 100 images (alkaline), Approx. 360 images (NiMH)

Rec

ordi

ng S

peci

ficat

ions

Recording Media SD memory card, SDHC memory card, MultiMediaCard, MMCplus card, HC MMCplus card

SD memory card, SDHC memory card, MultiMediaCard

File Format Design rule for camera file system, DPOF (Version 1.1) compliant

Data TypeStill Images Exif 2.2 (JPEG)Movies AVI (Image data: Motion JPEG, Audio data: WAVE (Monaural))Audio Sound memos: WAVE (Monaural)

Number of Recording Pixels

Still ImagesLarge: 3264 x 2448, Medium 1: 2592 x 1944, Medium 2: 2048 x 1536, Medium 3: 1600 x 1200,Small: 640 x 480, Postcard date imprint: 1600 x 1200, Widescreen: 3264 x 1832

Large: 3072 x 2304, Medium 1: 2592 x 1944, Medium 2: 2048 x 1536, Medium 3: 1600 x 1200,Small: 640 x 480, Postcard date imprint: 1600 x 1200, Widescreen: 3072 x 1728

Movies Standard: 640 x 480 (30 fps/30 fps LP) / 320 x 240 (30 fps)Compact: 160 x 120 (15 fps)

Standard, Color Accent, Color Swap: 640 x 480 (30/15 fps) / 320 x 240 (30/15 fps)Fast Frame Rate: 320 x 240 (60 fps)Compact: 160 x 120 (15 fps)

Others –

Play

back

Spec

ificat

ions

Main Features

Still ImagesRed-eye correction, index, resize, magnified, advancing and reversing through magnified images, jump, auto rotate, rotate, histogram, overexposure warning, sound memos, auto play, transition effects, resume

Index, My Colors, magnified, advancing and reversing through magnified images, jump, auto rotate, rotate, histogram, overexposure warning, sound memos, auto play, resume (Still images only)

Movies Special playback Special playback, editingDirect Print PictBridge, Canon Direct Print, Bubble Jet Direct

Display Languages 25 languages (The models for Japanese market available with 2 languages (Japanese and English) only.) 25 languages

Interface USB 2.0 Hi-Speed (mini-B)*, Audio/Video output* MTP, PTP supported

USB 2.0 Hi-Speed (mini-B)*, Audio/Video output* PTP supported

Power Source2 AA Alkaline batteries2 AA rechargeable NiMH batteries (NB4-300/NB4-200)AC Adapter Kit ACK800

Dimensions (excluding protrusions) 108.7 x 71.4 x 46.7 mm (4.28 x 2.81 x 1.84 in.) 97.5 x 66.5 x 41.2 mm (3.84 x 2.62 x 1.62 in.)Weight (camera body only) Approx. 265 g (9.35 oz.) Approx. 210 g (7.41 oz.)

6

2 Exterior

2-1 Exterior Photos

Silver model

Black model

7

2-2 6-view Diagram

6.0-60.0mm 1:2.8-4.3

Unit : mm (inch)* Nominal Dimensions

108.7* (4.28*)

35.3

(1.3

9)41

.6 (1

.64)

71.4

* (2.

81* )

46.7

* (1.

84* )

8

2-3 Nomenclature

9

3 Specifications

3-1 Product SpecificationsNote: Measured data is based on Canon’s standard testing conditions unless otherwise stated.

Imaging Processor DIGIC III

Image Sensor (CCD)

Camera Effective Pixels Approx. 8.0 million pixelsTotal Pixels Approx. 8.3 million pixelsTransfer Method InterlineImage Size 1/2.5-inch typeAspect Ratio 4:3Filter Type Primary color filters (Bayer type)

Lens

Focal Length 6.0 (W) – 60 (T) mm (35mm film equivalent: 36 (W) – 360 (T) mm)f/number (widest aperture) f/2.8 (W) – f/4.3 (T)Lens Construction 10 elements in 9 groups (including 1 aspherical lens)Zoom Magnification 10xImage Stabilizer System Lens-shift type

Effect Approx. 3 stepsFocusing Range and Image Area (Image magnification ratios are 35mm film equivalent)

*1 Excluding Fireworks.*2 Cannot be selected in Landscape.*3 Cannot be selected in Stitch assist and Auto.

Optical Viewfinder Not available

Electronic Viewfinder Not available

Shooting Mode

Max. Wide Angle Max. Telephoto

Focusing RangeImage Area at the Minimum Focusing

Distance[Image Magnification]

Focusing RangeImage Area at the Minimum Focusing

Distance[Image Magnification]

Auto, P, Tv, Av, M, Portrait, Landscape, Night Snapshot, Special Scene*1, Stitch Assist, Movie

Normal 50 cm (1.6 ft.)– infinity – 1 m (3.3 ft.)

– infinity –

Macro*2 1 – 50 cm(0.39 in. – 1.6 ft.)

29 x 21 cm(1.1 x 0.83 in.)

[0.22x]– –

Manual Focus*3 1 cm (0.39 in.)– infinity

29 x 21 cm(1.1 x 0.83 in.)

[0.22x]1 m (3.3 ft.)

– infinity119 x 89 mm(4.7 x 3.5 in.)

[0.05x]Fireworks Not disclosed – Not disclosed –

Kids & Pets 1 m (3.3 ft.)– infinity – 1 m (3.3 ft.)

– infinity –

10

LCD Monitor

Type Low-temperature polycrystalline silicon TFT colorEffective Pixels Approx. 172,000 pixelsDisplay Size 62.3 mm diagonal (2.5-inch type), with wide viewing anglePicture Coverage 100%Brightness Adjustment 15 levelsQuick-bright LCD AvailableVariangle Not available

Focus Control

AF System TTL autofocusAF Mode Single, continuousManual Focus Available

• Shooting standby only in movie mode.

MF-Point Zoom AvailableMF Indicator Available (unit used to indicate distances selectable)Focus Fine Tuning Not availableSafety MF Available

AF Frame Face Detect*, center* If no face is detected, 1-points is used.• AF frame can be moved and fixed to specified face.

Size Select Available (Normal, Small)• Center can only be selected.

AF Lock Available• Shooting standby only in movie mode.

AF-assist Beam Available

Exposure Control

Metering System Evaluative*1, Center-weighted average, Spot*2*1 Control to incorporate facial brightness in Face Detect AF.*2 Fixed to center.

Manual Exposure Available (M mode only)AE Lock Available

• Still images only.

Exposure Compensation(Still images)

±2 stops in 1/3-stop increments

Exposure Shift (Movies) ±2 stops in 1/3-stop increments• Shooting standby only.

Program Shift AvailableSafety Shift AvailableISO Speed(Standard Output Sensitivity, Recommended Exposure Index)

Auto*1, High ISO Auto*2, ISO 80/100/200/400/800/1600*1 Camera automatically sets the optimal speed according to subject brightness.*2 Camera automatically sets the optimal speed according to subject brightness.

However, the ISO speed is set relatively higher than Auto.

Auto ISO Shift Off, Manual, OnND Filter (built-in) Insertion Not available

11

White Balance

Modes Auto, Day Light, Cloudy, Tungsten, Fluorescent, Fluorescent H, Custom

Shutter, Aperture

Shutter Type Mechanical shutter and electronic shutterAperture Type Iris typeShutter Speeds 15 – 1/2500 sec.

• Shutter speeds vary depending on the shooting modes.• The following shutter speeds are available in Tv mode or M mode:

15, 13, 10, 8, 6, 5, 4, 3.2, 2.5, 2, 1.6, 1.3, 1, 0.8, 0.6, 0.5, 0.4, 0.3, 1/4, 1/5, 1/6, 1/8, 1/10, 1/13, 1/15, 1/20, 1/25, 1/30, 1/40, 1/50, 1/60, 1/80, 1/100, 1/125, 1/160, 1/200, 1/250, 1/320, 1/400, 1/500, 1/640, 1/800, 1/1000, 1/1250, 1/1600, 1/2000, 1/2500 (Unit: sec.)

f/number f/2.8 – f/8.0* (W) / f/4.3 – f/8.0* (T)* The f/number can be set to f/11 when Auto mode.• The following f/numbers are available in Av mode or M mode:

W: f/2.8, 3.2, 3.5, 4.0, 4.5, 5.0, 5.6, 6.3, 7.1, 8.0T: f/4.3, 5.0, 5.6, 6.3, 7.1, 8.0

Relationship between f/number and Shutter Speeds

Max. wide angle

Max. telephoto

• Settable shutter speeds vary depending on the camera’s shooting mode.* The f/number can be set to f/11 when Auto mode.

Flash

<Built-in>Flash Modes Auto, on, offFlash Range 50 cm – 3.0 m (W), 50 cm – 2.0 m (T)

(1.6 – 9.8 ft. (W), 1.6 – 6.6 ft. (T)) (ISO speed: Auto)• Brightness of image periphery may reduce depending on shooting distance.

Flash Synchro Shutter Speeds 1/500 sec. (Fastest synchronized shutter speed)Recycling Time (Full Flash) 12 sec. or less (battery voltage: 3 V)

• LCD monitor is turned off during flash charging (Except when turning on the power).

Flash Output Compensation ±2 stops in 1/3-stop incrementsManual Flash Output Setting 3 stepsFE Lock AvailableRed-eye Reduction AvailableSlow Synchro AvailableSecond-curtain Synchro Not availableSafety FE Available

<External> Not available

<Auxiliary>Recommended Flash High-Power Flash HF-DC1Mounting Method Mount to the supplied bracket using tripod socketTrigger System Detects the flash light from the camera’s built-in flash

f/number f/2.8 – f/3.5 f/4.0 – f/5.0 f/5.6 – f/8.0*

Shutter Speed (sec.) 15 – 1/1600 15 – 1/2000 15 – 1/2500

f/number f/4.3 – f/5.6 f/6.3 – f/8.0*

Shutter Speed (sec.) 15 – 1/1600 15 – 1/2000

12

Shooting Specifications

<Still Images, Movies>Shooting Modes Auto, P, Tv, Av, M, Portrait, Landscape, Night Snapshot, Kids & Pets, Special Scene*,

Stitch Assist, Movie* Night Scene, Indoor, Foliage, Snow, Beach, Fireworks, Aquarium

Long Shutter Mode Not availableDigital Zoom

Zoom Magnification Approx. 4.0x, up to approx. 40x in combination with the optical zoom• In still image mode, digital zoom is not available for the mode set to Postcard Date

Imprint or Widescreen.• In movie mode, digital zoom is only available for the mode set to Standard, and the opti-

cal zoom can be used in shooting standby.

Focal Length(Optical x Digital)

36 (W) – 1440 (T) mm (35mm film equivalent)

Zoom Position(Optical x Digital)

13x, 16x, 20x, 26x, 32x, 40x

Safety Zoom(Stop position: Optical x Digital)

• Maximum magnification without loss of image quality at the each recording pixel.

Digital Tele-converter Approx. 1.6x, approx. 2.0x

My Colors (Limited type) My Colors Off, Vivid, Neutral, Sepia, Black & White, Custom Color** Adjustment of contrast, sharpness and saturation are available.• Saving original image is not available.

Auto Category Not availableImage Stabilizer

Modes Off, Continuous, Shoot Only*, Panning** Still images only.

Converter Settings Not availableCamera Start-up Time, Release Time Lag

* When flash is turned off.

Self-timer Shooting Approx. 10-sec./approx. 2-sec. delay or custom** Still images only. Shooting start time (0 – 10 sec. (in one-second increments), 15/20/30 sec.)

and number of shots (1 – 10 shots (in one-shot increments)) can be specified.

Wireless Controlled Shooting Not availableRemote Shooting Available (using supplied software)Disp. Overlay Off, Grid lines, 3:2 Guide*, Both*

* Still images only.

Large Medium 1 Medium 2 Medium 3 Small10x 13x 16x 20x 40x

Magnification Focal length (35mm film equivalent)1.6x 57.6 (W) – 576 (T) mm2.0x 72.0 (W) – 720 (T) mm

Mode LCD Monitor Camera Start-up Time* Release Time LagShooting On Approx. 1.8 sec. 0.1 sec. or lessPlayback On Approx. 1.2 sec. –

13

<Still Images>Noise Reduction Available (When shutter speed is set between 15 and 1.3 sec.)Bracketing Not availableRec. Review Off, 2 – 10 sec. (in one-second increments), Hold

• Magnification and image erasing are also available.

Image Inspection Tool AvailableNight Display AvailableShooting Interval

• Large and Fine• Digital zoom is not used.• The flash does not fire.• ISO speed is set to Auto.• Normal temperature• The actual shooting interval time consists of the shutter speed added to the above times.

Continuous ShootingMode Selection Continuous shooting, continuous shooting AF, continuous shooting LVSpeed Continuous shooting: Approx. 1.3 shots/sec.

Continuous shooting AF: Approx. 0.8 shots/sec.Continuous shooting LV: Approx. 0.8 shots/sec.

• Large and Fine• Digital zoom is not used.• The flash does not fire.• ISO speed is set to Auto.• Normal temperature• The actual shooting interval time consists of the shutter speed added to the above times.

Number of Shots

: Smooth continuous shooting available (See the Recording Capacity for detailed values)*1 Postcard Date Imprint Mode is also available.*2 Memory card included with the camera.• Even after exceeding the number of shots shown above, continuous shooting is available

when the shutter button is still pressed. However, the shooting speeds will decrease.

Interval Shooting Not available

<Movies>Modes Standard, Compact

LCD Monitor Shooting IntervalOn Approx. 1.7 sec.Off –

<Low Level Format> Unit: shots

Large (L) Medium 1 (M1) Medium 2 (M2) Medium 3 (M3) Small (S) Widescreen (W)

SF F N SF F N SF F N SF F*1 N SF F N SF F N

16MB*2 (SD) 2 4 3 8 7 3 7

SDC-128M 2 5 86 3 18 9 3 8

SDC-512MSH 2

14

Audio Specifications

Audio Functions Movie sound, sound memosQuantization Bit Rate/Sampling Rate

Input Level Adjustment AutoInput Level Indicator Not availableWind Filter Not available

Microphone, Speaker Available

Recording Specifications

<Still Images, Movies>Recording Media SD memory card, SDHC memory card, MultiMediaCard, MMCplus card,

HC MMCplus cardFormat Normal format, low level formatFile Format Design rule for camera file system, DPOF (Version 1.1) compliantData Type Still images: Exif 2.2 (JPEG)

Movies: AVI (Image data: Motion JPEG; Audio data: WAVE (monaural))Sound memos: WAVE (monaural)

Folder Settings ManagementCapacity Max. 900, up to 2,000 files can be stored per folderCustomization Available (Create New Folder (on next shooting), Auto Create*)

* Off, or user-specified time per day, month, day of the week.

<Still Images>Color Space Standard (sRGB)Compression Superfine, fine, normalNumber of Recording Pixels

* Compression is fixed to fine.

Recording Capacity

• The approximate number of images recordable on memory cards of 1 GB and above can becalculated by using the figures for 512 MB as a reference and extrapolating accordingly.

*1 Postcard Date Imprint Mode is also available.*2 Memory card included with the camera.

Quantization Bit Rate Sampling Rate

Movie soundStandard 8 bits 11 kHzCompact 8 bits 11 kHz

Sound memos 8 bits 11 kHz

Unit: pixelsLarge 3264 x 2448

Medium 1 2592 x 1944Medium 2 2048 x 1536Medium 3 1600 x 1200

Small 640 x 480Postcard date imprint* 1600 x 1200

Widescreen 3264 x 1832

Unit: imagesLarge (L) Medium 1 (M1) Medium 2 (M2) Medium 3 (M3) Small (S) Widescreen (W)

SF F N SF F N SF F N SF F*1 N SF F N SF F NFile Size (KB) 3436 2060 980 2503 1395 695 1602 893 445 1002 558 278 249 150 84 2601 1540 736

16MB*2 (SD) 3 6 13 5 9 19 8 15 30 13 24 47 52 81 128 5 8 18SDC-128M 35 59 123 49 87 173 76 136 269 121 217 411 460 711 1118 47 79 166SDC-512MSH 139 231 479 190 339 671 295 529 1041 471 839 1590 1777 2747 4317 183 307 642

15

<Movies>Recording Pixels, Frame Rate

Maximum Recording Length per Clip

Standard: Continuous recording is possible until the file size reaches 4 GB*

Compact: 3 min.* Even if the file size has not reached 4 GB, the recording is stopped when the recording

time reaches one hour. Depending on memory card capacity and data write speed, record-ing may stop before the file size reaches 4 GB or the recording time reaches one hour.

: Continuous recording is possible until the memory card becomes full* Memory card included with the camera.

Recording Time

• The approximate recording time available on memory cards of 1 GB and above can becalculated by using the figures for 512 MB as a reference and extrapolating accordingly.

* Memory card included with the camera.

<Audio>Recording Time

Sound Memos Up to 1 minute recording length per image

Recording Pixels Frame Rate

Standard640 x 480 30 fps/30 fps LP320 x 240 30 fps

Compact 160 x 120 15 fps

<Low Level Format>Standard Compact

640 x 480 320 x 240 160 x 12030 fps 30 fps LP 30 fps 15 fps

16MB* (SD)SDC-128M 29 sec. 3 min.SDC-512MSH 3 min.

Standard Compact640 x 480 320 x 240 160 x 120

30 fps 30 fps 30 fps 15 fpsMovie Size (KB/sec.) 1920 960 660 120

16MB* (SD) 6 sec. 14 sec. 20 sec. 1 min. 40 sec.SDC-128M 1 min. 4 sec. 2 min. 7 sec. 3 min. 1 sec. 14 min. 29 sec.SDC-512MSH 4 min. 9 sec. 8 min. 14 sec. 11 min. 42 sec. 55 min. 57 sec.

16

Playback Specifications

<Still Images, Movies>Auto Rotate (Automatic vertical/horizontal detection)

Available (owing to the Intelligent Orientation Sensor)• Images are displayed vertically or horizontally according to the camera’s shooting posi-

tion. For movie playback, the direction depends on the camera’s position at the start ofshooting.

• The setting for playback is linked to the setting chosen for shooting.

Resume Playback Available

<Still Images>Maximum Playback Pixels 5616 x 3744Playback Modes Single, index (9 thumbnail images)Red-eye Correction AvailableMagnification Approx. 2x – 10x

• Advancing and reversing through magnified images available.

Rotate Rotates each image to 90 degrees or 270 degrees• Both the LCD monitor and video output play back the image according to settings.

RAW Playback(CR2 datatype)

Available

Resize Available• Recording pixels after “Resize”: 1600 x 1200, 640 x 480 or 320 x 240 pixels.

My Colors Not availableMy Category Not availableJump Top of the specified Shot Date, Folder, Movie, By 10 images, By 100 images

• Jumps to the next set of nine images each time button is pressed during index playback.

Image Inspection Tool AvailableHistogram AvailableOverexposure Warning AvailableAuto Play

Playback interval 3 sec.Repeat Always On

Transition Effects 2 types (Single image playback, Auto Play)

<Movies>Playback Functions Normal playback, slow motion*, pause, first frame, last frame, next frame, and pre-

vious frame selectable. Fast forward and fast rewind are available.• Display playback position and shooting time.* 5 speed levels including normal-playback speed, without sound.

Editing Not availableCompatibility See 3-5 Playback Compatibility

Printing Specifications See 3-4 Direct Print

Direct Print PictBridge, Canon Direct Print, Bubble Jet DirectDPOF (Version 1.1)

Print Specification Select images & quantity for printing*, Select all images• Up to a total of 998 images can be specified.* Up to 99 prints of one image can be specified (other options allow only one print per

image).

Print Settings Print Type, Date, File No.

17

Erasing Specifications

Erasing Modes Single image, Select all images• The image data in the memory card stored with the design rule for camera file systems

format can be erased. (However, protected images can not be erased.)• As for movies, every file can be erased.

Protect (camera) Available• Each image or sound memo must be specifyed.

Protect (SD memory card/SDHC memory card)

Prevents erasing any data recorded on the SD memory card and SDHC memory card

Interface

Computer Interface USB 2.0 Hi-Speed (mini-B jack)Communication Settings MTP, PTPAudio Output Monaural (ϕ 3.5 mm jack: Unified type for audio and video output)Video Output NTSC or PAL (ϕ 3.5 mm jack: Unified type for audio and video output)

Others

Display Languages 25 languages*

(English, German, French, Dutch, Danish, Finnish, Italian, Norwegian, Swedish, Spanish, Simplified Chinese, Russian, Portuguese, Greek, Polish, Czech, Hungarian, Turkish, Traditional Chinese, Korean, Thai, Arabic, Romanian, Ukrainian, and Japanese)* The models for Japanese market available with 2 languages (Japanese and English) only.

Battery Level Indicator Not available• Battery icon blinks when the charge is low.

My Camera Not available• With the start-up image, start-up sound, operation sound, self-timer sound and shutter

sound, Canon original contents are installed

Lens Retraction Timing 0 sec. (immediately), 1 min. laterDate Function

Date Stamp Off, Date, Date & time• Postcard Date Imprint only.

Date Settings Available up to the year 2037Date Style Year/month/day, month/day/year or day/month/year

Clock Display Not availableWorld Time Display Not availableDirect Transfer Available (Windows/Macintosh)

All Images, New Images, DPOF Trans. Images*, Select & Transfer, Wallpaper* Only images with check-marks applied by the DPOF function can be transferred.

Operation Sound Volume adjustable (6 levels)Mute Available (including warning sound)Shortcut Settings Disabled (default), white balance, Custom white balance (Acquisition of white data),

digital tele-converter, Disp. overlay, display offReset of All Settings Available

18

Power Supplies

Primary Batteries AA alkaline batteries (x2)Secondary Batteries AA rechargeable NiMH batteries NB-3AH (x2)AC Adapter Compact Power Adapter CA-PS800Car Battery Adapter Not availableSub-battery Coin-type lithium battery CR1220 (Primary battery)

Life Approx. 4 yearsBattery Capacity

Number of Images Shot

Playback Time

Power Saving FunctionAuto Power Down (when in idle) Available

• Shooting mode: Approx. 3 min. later• Playback mode: Approx. 5 min. later• Connection to printer: Approx. 5 min. later• Auto play/connection to computer: The power saving function does not activate

Display Off 10/20/30 sec., 1/2/3 min.• The Intelligent Orientation Sensor detects the camera being moved and recovers from the

display-off function.

Camera Specifications

Operating Temperatures 0 – 40°C (32 – 104°F)• 0 – 35°C (32 – 95°F) when NB-3AH is used.

Operating Humidity 10 – 90%Dimensions (excluding protrusions) 108.7 x 71.4 x 46.7 mm (4.28 x 2.81 x 1.84 in.)Weight (camera body only) Approx. 265 g (9.35 oz.)

Canon Standard(LCD monitor Off)

Alkaline batteries(Panasonic brand) Approx. 140 shots

NiMH batteries (NB-3AH) Approx. 400 shots

Alkaline batteries(Panasonic brand) Approx. 7 hours

NiMH batteries (NB-3AH) Approx. 10 hours

19

3-2 System Diagram

20

3-3 Shooting/Setting Features List

[How to read symbols in the table]

! : Setting available or optimum value is automatically set by the camera. As a rule, with the "Stitch Assist", only the first image is available.X : Not available.Colored cells ( ) : The settings are retained even when the camera power is turned off.

*1 : Set to Continuous Shooting LV when Manual Focus or Fireworks is selected.*2 : Postcard Date Imprint and Widescreen are not available.*3 : Can not fire, when flash is not pop-up.*4 : Can not be set when Postcard Date Imprint or Widescreen is selected.*5 : Always set to on.*6 : Always set to off.*7 : Only available when Flash-on is selected.

21

3-4 Direct Print3-4-1Print Features of Direct Print

•Printing with SELPHY CP Series PrintersThe product name of the camera and the printer that has been described in the table is Japanese names. However, the product not sold in Japan has described an overseas name.

Canon Direct Print features 1 2 3

[NOTE]*1 1 to 99 copies can be set per image.*2 Prints one image per page.*3 Prints eight copies of the same image on one page. This

option can only be selected when printing on credit cardsize paper. When the print style is set to [Multiple],images are printed without any date or border.

*4 In PowerShot A20/A10 and IXY DIGITAL 300/200,trimming is not possible. In PowerShot A60/A40/A30/A200/A100 and IXY DIGI-TAL 300a/200a, you can select the print area from thetop-/center-/buttom-aligned. Depending on a paper sizeand aspect ratio of the image, the print area may bealigned to the left or right. However, the print area can beset, when the print style is [Borderless] and [Multiple].

*5 When the print type is set to [Index], the [Date] cannotbe printed.

*6 When the print type is set to [Standard], the [File Num-ber] cannot be printed.

*7 Communication setting with the printers (CP750/740/730/720/710/520/510) needs to be changed to Pict-Bridge for full-sized borderless printing on wide-sizepaper.

Easy Print

Single Image Print O O OSetting the Number of Copies*1 O O O

Setting the Print Style

Standard*2 O O OMultiple*3 O O OID Photo Print × O OBorderless / Bordered O O ODate O O O

Setting the Print Area (Trimming) O*4 O O

Movie PrintSequence-frame × O OSingle-frame × × O

Printing with DPOF Print

Settings

Several Selected Images Print O O OAll Image Print O O OSetting the Number of Copies*1 O O O

Selecting the Print TypeStandard O O OIndex O O OBoth (Standard + Index) O O O

Date and File Number PrintDate*5 O O OFile Number*6 O O O

Setting the Print StyleStandard*2 O O OMultiple*3 O O OBorderless / Bordered O O O*7

PictBridge features!: Canon proprietary feature

4 5 6 7

Easy Print

Single Image Print O O O O [NOTE]*1 Uses the camera's shooting information to

optimize the image data.*2 Red-eye correction only.*3 Red-eye + NR + Face brightness adjustment.*4 1 to 99 copies can be set per image.*5 For the usable paper size, refer to the printer

user guide.*6 Default only.*7 Prints 2, 4 or (8) images on a single sheet of

paper. (8 can only be selected when printingon credit card size paper.)

*8 Prints by specifying the print size of theimage on a sheet of paper. For the paper sizeand the print size, refer to the direct print userguide.

*9 Only available with cameras supportingMovie Print (in single frames) function.

*10When the print type is set to [Index], the[Date] and [File Number] cannot be set at thesame time.

Date and File Number PrintDate O O O OFile Number × O O O

Setting the Print Effect

Auto*1 (On/Off) O O O O

! VIVID / NR / VIVID+NR × × × ×! Face brightness adjustment × × × ×! Red-eye1 correction*2 × × × O

! Red-eye2 correction*3 × × × ×Setting the Number of Copies*4 O O O OSetting the Print Area (Trimming) O O O OSelecting the Paper Size*5 O O O OSelecting the Paper Type*6 O O O O

Setting the Layout

Borderless / Bordered O O O ON-up*7 × O O OFixed Sixe*8 × O O O

! ID Photo Print × O O O

! 20 image index with shooting information × × × ×! Contact-sheet type 35 image index × × × ×

Print with the shooting information × × × ×

Movie Print ! Sequence-frame × O O OSingle-frame*9 × × O O

Printing with DPOF Print

Settings

Several Selected Images Print O O O OAll Image Print O O O O

Selecting the Print TypeStandard O O O OIndex O O O OBoth (Standard + Index) O O O O

Date and File Number PrintDate*10 O O O OFile Number*10 × O O O


Auto*1 (On/Off) O O O O! VIVID / NR / VIVID+NR × × × ×! Face brightness adjustment × × × ×! Red-eye1 correction*2 × × × O

! Red-eye2 correction*3 × × × ×Setting the Number of Copies*4 O O O OSelecting the Paper Size*5 O O O OSelecting the Paper Type*6 O O O O

Setting the Layout

Borderless / Bordered O O O ON-up*7 × O O OFixed Sixe*8 × O O O

! ID Photo Print × × × ×! 20 image index with shooting information × × × ×! Contact-sheet type 35 image index × × × ×

Print with the shooting information × × × ×

ES2 / ES20

22

•Printing with Canon Bubble Jet Printers (PIXMA series/SELPHY DS series)The product name of the camera and the printer that has been described in the table is Japanese names. However, the product not sold in Japan has described an overseas name.

Bubble Jet Direct features 1

Easy Print

Single Image Print O [NOTE]*1 1 to 99 copies can be set per image.*2 For the usable paper size, refer to the printer user guide.*3 In PowerShot A60 and IXY DIGITAL 300a/200a, you can select the print area

from Top/Center/Bottom. Depending on a paper size and aspect ratio of the image, the print area may be aligned to the left or right. However, the print area can be set when the print style is [Borderless].

Setting the Number of Copies*1 O

Setting the Print StylePaper Size*2 OBorderless / Bordered ODate O

Setting the Print Area (Trimming) O*3

Printing with DPOF

PrintSettings

Several Selected Images Print OAll Image Print OSetting the Number of Copies*1 O

Selecting the Print TypeStandard OIndex OBoth (Standard + Index) O

Date and File Number PrintDate OFile Number ×

Setting the Print Style Borderless / Bordered O

PictBridge features!: Canon proprietary feature

2 3 4 5 6 7 8 9 *

Easy Print

Single Image Print O O O O O O O O O [NOTE]*1 Uses the camera's shooting informa-

tion to optimize the image data.*2 VIVID only.*3 Red-eye correction only.*4 Red-eye + NR + Face brightness

adjustment.*5 1 to 99 copies can be set per image.*6 For the usable paper size, refer to

the printer user guide.*7 For the usable paper type, refer to

the printer user guide.*8 Prints 2, 4, 9 or 16 images on a sin-

gle sheet of paper. The number of images that can be arranged on a single sheet of paper is different depending on the printer and the paper size. Then, refer to the print user guide.

*9 Not available when connecting with the PIXUS Pro9500 printer.

*10Prints by specifying the print size of the image on a sheet of paper. For the paper size and the print size, refer to the direct print user guide.

*11Only available with cameras sup-porting 20 image index layout with shooting information.

*12Only available with cameras sup-porting contact-sheet type 35 image index layout.

*13Not available when printing without borders.

*14[Single-frame] is only possible, when the camera corresponds to the Movie print (Single-frame).

*15When the print type is set to [Index], the [Date] and [File Num-ber] cannot be set at the same time.

*16When the print type is set to [Stan-dard], the [File Number] cannot be printed.

Date and File Number Print

Date O O O O O O O O OFile Number × × × × O O O O O


Auto*1 (On/Off) O O O O O O O O O

! VIVID / NR / VIVID+NR × !*2 O O O O O O O

! Face brightness adjustment × × × × × O O O O

! Red-eye1 correction*3 × × × × × × × × O

! Red-eye2 correction*4 × × × × × × × O OSetting the Number of Copies*5 O O O O O O O O OSetting the Print Area (Trimming) O O O O O O O O OSelecting the Paper Size*6 O O O O O O O O OSelecting the Paper Type*7 O O O O O O O O O

Setting the Layout

Borderless / Bordered O O O O O O O O ON-up*8 × × × O*9 O*9 O O*9 O*9 OFixed Sixe*10 × × × × × × × × ×

! ID Photo Print × × × × × × × × ×! 20 image index with shooting information*11 × × × × × × O O O

! Contact-sheet type 35 image index*12 × × × × × × O O OPrint with the shooting information*13 × × × × × × O O O

Movie Print ! Sequence-frame × × × × × × × × ×Single-frame*14 O O O O O O O O O

Printing with DPOF

PrintSettings

Several Selected Images Print O O O O O O O O OAll Image Print O O O O O O O O O

Selecting the Print TypeStandard O O O O O O O O OIndex O O O O O O O O OBoth (Standard + Index) O O O O O O O O O

Date and File Number Print

Date*15 O O O O O O O O OFile Number*15 16 × × × × O O O O O


Auto*1 (On/Off) O O O O O O O O O

! VIVID / NR / VIVID+NR × !*2 O O O O O O O

! Face brightness adjustment × × × × × O O O O

! Red-eye1 correction*3 × × × × × × × × O

! Red-eye2 correction*4 × × × × × × × O OSetting the Number of Copies*5 O O O O O O O O OSelecting the Paper Size*6 O O O O O O O O OSelecting the Paper Type*7 O O O O O O O O O

Setting the Layout

Borderless / Bordered O O O O O O O O ON-up*8 × × × O*9 O*9 O O*9 O*9 OFixed Sixe*10 × × × × × × × × ×

! ID Photo Print × × × × × × × × ×! 20 image index with shooting information*11 × × × × × × O O O

! Contact-sheet type 35 image index*12 × × × × × × O O OPrint with the shooting information*13 × × × × × × O O O

23

3-4-2 The Connection between Digital Cameras and PrintersThe connection between Canon digital cameras (PowerShot series and IXY series) and printers shows in Table 1.

Digital Cameras

Printers

Canon Direct Print / Bubble Jet Direct / PictBridge support

Canon Direct Print / Bubble Jet Direct support

Canon Direct Printsupport

Cameras released in 2006 and 2007

Cameras released in 2003 and 2005

(Except for PS A520/A510)PS Pro1/S1 IS

Cameras released in 2004(Except for PS Pro1/S1 IS)

PS A520/A510PS G3/G2/S45/S40/S30,ID 320/300a/200a

PS A40/A30/A20/A10/A200/A100,ID 300/200

CP series (Canon Direct Print support)

CP-10CP-100

CP series(Canon Direct Print, PictBridge support)

CP-200/300CP220/330

Canon Direct Print /PictBridge*

Canon Direct Print

SELPHY CP series (Canon Direct Print, PictBridge support)

CP750/740/730/720/710/520/510/500/400

ES2/ES20ES1, CP600 PictBridge

PIXMA series (Bubble Jet Direct support) -

PIXMA series(Bubble Jet Direct, PictBridge support)

PictBridge

Bubble Jet Direct -

SELPHY DS series(Bubble Jet Direct, PictBridge support) -

Other manufacturer’s Printer(PictBridge support) - -

• IXY (ID) is the name for Japanese market.• The supporting digital cameras and printers are included by improvement of the version of the firmware.• For SLR digital cameras and video cameras, refer to their Technical Guidance.* It is possible to change printer connection to PictBridge with the camera. However, the change is unnecessary, except when full-sized borderless printing on wide-size paper with

CP750/740/730/720/710/520/510.

Table 1 The conuection between Digital Cameras and Printers

24

3-5 Playback Compatibility3-5-1 Still Images

Cameras for playback (except SLR cameras)

CF card SD SD/MMC*SD/SDHC/MMC*

(MMCplus: TX1 only)

SD/MMC/SDHC/MMCplus/

HC MMCplusID 400/320/300a/300/200a/200, IXY DIGITALPS S20/S10PS A70/A60/A40/A30/A20/A10/A300/A200/A100

PS G3/G2/G1PS Pro90 ISPS S50/S45/S40/S30

PS Pro1PS G6/G5PS S70/S60

ID 500/450PS S1 ISPS A95/A85/A80/A75/A310

ID 30 ID 600/55/50/40/30a/L2/LPS S2 ISPS A400

ID 800 IS/700/80/70/60/L3/WIRELESSPS S80/A700/A620/A610/A540/A530/A520/A510/A430/A420/A410

ID 1000/900 IS/810 IS/90/10/L4

PS G7/S3 IS/S5 IS/TX1PS A710 IS/A640/A630/A570 IS/A560/A550/A460/A450

ID 2000 IS /910 ISPS G9 /SX 1000 ISPS A720 IS /A650 IS

Cam

eras

for s

hoot

ing

(exc

ept S

LR c

amer

as) CF

ID 500/450/400/320/300a/300/200a/200, IXY DIGITALPS S1 IS/S20/S10PS A95/A85/A80/A75/A70/A60/A40/A30/A20/A10/A310/A300/A200/A100

O O O O ! ! ! ! !

PS G6/G5/G3/G2/G1PS Pro90 ISPS S70/S60/S50/S45/S40/S30

O*1 O O O*1 !*1 !*1 ! ! !

PS Pro1 O*1*2 O*2 O O*1 !*1*2 !*1 ! ! !

SDID 600/55/50/40/30a/30/L2/LPS S2 ISPS A400

! ! ! ! O O O O O

SD/MMC*ID 800 IS/700/80/70/60/L3/WIRELESSPS A700/A620/A610/A540/A530/A520/A510/A430/A420/A410 ! ! ! ! O O O O O

PS S80 !*2 !*2 ! ! O*3 O*3 O O O

SD/SDHC/MMC*

(MMCplus: TX1 only)

ID 900 IS/90/10/L4

PS S3 IS/TX1PS A710 IS/A570 IS/A560/A550/A460/A450

!*4 !*4 !*4 !*4 O*4 O*4 O*4 O O

ID 1000/810 ISPS G7/S5 ISPS A640/A630

!*2 *4 !*2 *4 !*4 !*4 O*3 *4 O*3 *4 O*4 O O

SD/SDHC/MMC*/MMCplus/HC MMCplus

ID 2000 IS / 910 ISPS G9 / SX 1000 ISPS A720 IS / A650 IS

!*2 *4 *5 !*2 *4 *5 !*4 *5 !*4 *5 O*2 *3 *4 *5 O*3 *4 *5 O*4 *5 O*5 O

PS G9 RAW image X X X X X X X X O*6

*1Thumbnail is displayed for RAW image*2JPEG file can be played-back up to 3200 x 2400 pixels (Thumbnail displays when more than 3200 x 2400 pixels)*3Images recorded in the MultiMediaCard may not be played-back. *4Images recorded in the SDHC memory card can not be played-back.*5Images recorded in the HC MMCplus card can not be played-back.*6JPEG image is played-back accompanied for display.* MultiMediaCard

PS : PowerShotID : IXY DIGITAL (The model names of IXY are for Japanese market)O: Playback available!: Playback available when interchange of memory cards X: Playback not available

25

3-5-2 MoviesCameras for playback

CFcard SD SD/MMC* SD/SDHC/MMC*

(MMCplus: TX1 only)SD/MMC/SDHC/

MMCplus/HC MMCplus

IXY DIGITALPS S20/S10PS A20/A10

PS G2/G1PS Pro90 ISPS S40/S30

ID 300a/300/200a/200PS A40/A30/A200/A100

PS Pro1/G6/G5/G3PS S70/S60/S50/S45ID 500/450/400/320PS A95/A85/A80/A75/A70/A60/A310/A300

PSS1 IS

ID30a/30/L2/LPS 400

ID 600/55/50/40PS S2 IS

PSA520/A510

ID 800 IS/700/80/70/60/L3/WIRELESSPS S80PS A700/A620/A610/A540/A530/A430/A420/A410

PS S3 ISPS A710 IS/ A640/A630/A550/A460/A450

ID 1000/900 IS/L4

PS G7

ID 90/10PS TX1/A570 IS/A560

ID 810 ISPS S5 IS

ID 2000 IS /910 ISPS G9 /SX 1000 ISPS A720 IS /A650 IS

Cam

eras

for s

hoot

ing

CF

PS G2/G1, PS Pro90 ISPS S40/S30 X O O*1 O O ! ! ! ! ! ! ! ! !

ID 300a/300/200a/200PS A40/A30/A200/A100

X O*1 O O O ! ! ! ! ! ! ! ! !

ID 500/450/400/320PS Pro1/G6/G5/G3/S70/S60/S50/S45PS A95/A85/A80/A75/A70/A60/A310/A300

X O*1 O*1 O O ! ! ! ! ! ! ! ! !

PS S1 IS X X X X O X ! X ! ! ! ! ! !

SD

ID 30a/30/L2/LPS 400

X !*1 !*1 ! ! O O O O O O O O O

ID 600/55/50/40 X X X X ! X O X O O O O O OPS S2 IS X X X X X X X X O O O O O O

SDMMC*

PS A520/A510 X !*1 !*1 ! ! O*2 O*2 O O O O O O OID 800 IS/700/80/70/60/L3/WIRELESSPS S80 (except XGA)PS A700/A620/A610/A540/A530/A430/A420/A410

X X X X ! X O*2 X O O O O O O

PS S80 (XGA) X X X X X X X X O O O O O O

SD/SDHC/MMC*

(MMCplus: TX1 only)

PS S3 IS (except 320 x 240, 60fps)PS A710 IS/A640/A630/A550/A460/A450 X X X X !*5 X O*2 *5 X O*5 O O O O O

PS S3 IS (except 320 x 240, 60fps) X X X X !*1 X X X O*5 O O O O OPS S3 IS (320 x 240, 60fps) X X X X X X X X X O O O O OID 1000/900 IS/810 IS*3/90*3/10*3/L4

PS G7/S5 IS/TX1*4

PS A570 IS/A560X X X X X X X X X X O O O O

PS TX1 (1280 x 720) X X X X X X X X X X X O X XID 810 IS/90/10 (Time Lapse) X X X X X X X X X X X O O O

SD/SDHC/MMC*/MMCplus/HC MMCplus

ID 2000 IS / 910 ISPS G9 / SX 1000 ISPS A720 IS / A650 IS

X X X X X X X X X X O*6 O*6 O*6 O

ID 2000 IS / 910 IS (Time Lapse)PS G9 X X X X X X X X X X X O*6 O*6 O

*1Playback not available when file size or recording time exceeds each limit.*2Images recorded in the MultiMediaCard (MMC) may not be played-back.*3Except Time Lapse Movie*4Except 1280 x 720*5Images recorded in the SDHC memory card can not be played-back.*6Images recorded in the HC MMCplus card can not be played-back.* MultiMediaCard

PS : PowerShotID : IXY DIGITAL (The model names of IXY are for Japanese market)O: Playback available!: Playback available when interchanging of memory cardsX : Playback not available

26

3-6 List of Accessory and Its Compatibility

3-6-1 Camera• PowerShot G Series, S Series, Pro Series

G9G7

S5 ISS3 ISS2 IS

S80 G6 S70S60

S1 IS Pro1 PS G5PS G3

S50S45S40S30

G2 Pro90 IS

G1

<Battery>NB-2L/2LH O - O - O - - - O - - -BP-511/511A - - - O - - O O - O O OBP-512/514 - - - O - - O O - O - -NB4-100/NB4-200 - O - - - O - - - - - -NB4-300 - O - - - O - - - - - -

<Adapter/Charger>ACK700 - - - - O - - - O - - -ACK-DC20 O - O - - - - - - - - -CA-PS700 (N) O O - - - O - - - - - -CA-560 - - - O - - O O - O O OCA-570 + CG-560/570 - - - O - - O O - O O OCR-560 - - - O - - O O - O O OCB-5L/CG-580 - - - O - - O O - O O OCB-2LT/CB-2LTE - - - - O - - - O - - -CB-2LW/2LWE O - O - - - - - - - - -CB-3AH(CBK-100) - O - - - O - - - - - -CB-4AH(CBK4-200) - O - - - O - - - - - -CBC-NB2 O - O - O - - - O - - -CB-5AH(CBK4-300) - O - - - O - - - - - -

<DC Coupler>DR-700 - - - - O - - - O - - -DR-20 O - O - - - - - - - - -

<Lens Accessory>WC-DC58 - - - - - - - - - O O OWC-DC58N - - - O - - - O - - - -WC-DC52A - - - - - O - - - - - -WC-DC58A - O - - - - - - - - - -WC-DC58B O - - - - - - - - - - -WC-DC10 - - O - - - - - - - - -TC-DC52B - - - - - O - - - - - -TC-DC58 - - - - - - - - - O - OTC-DC58N - - - O - - - O - - - -TC-DC58A - - - - - - O - - - - -TC-DC58B - O - - - - - - - - - -TC-DC58C O - - - - - - - - - - -TC-DC10 - - O - O - - - - - - -250D 58mm - - - O - - - O - O - O500D 52mm - - - - - O - - - - - -500D 58mm - O - - - - O - - - O -LA-DC52E - - - - - O - - - - - -LA-DC58 - - - - - - - - - O - OLA-DC58B - - - - - - - O - - - -LA-DC58C - - - - - - O - - - - -LA-DC58D - - - O - - - - - - - -LA-DC58E - O - - - - - - - - - -LA-DC58H O - - - - - - - - - - -LA-DC10 - - - - O - - - - - - -LA-DC20 - - O - - - - - - - - -FA-DC58A - - - - - - O - - - - -LH-DC58 - - - - - - - - - - O -LH-DC10 - - - - - - O - - - - -LH-DC20 - - - - - O - - - - - -LH-DC30 - - - O - - - - - - - -LH-DC40 - O - - - - - - - - - -LAH-DC20 - O O - - - - - - - - -LAH-DC10 - - - - - O - - - - - -

27

<Speedlite>220EX O O (S5 IS) - O - - O O - O O O380EX - - - O - - O O - O O O420EX - - - O - - O O - O O O430EX O O (S5 IS) - - - - - - - - - -550EX - - - O - - O O - O O O580EX O O (S5 IS) - O - - - - - - - -580EX II O O - O - - - - - - - -(MR-14EX) - O (S5 IS) - O - - O O - O - -(MT-24EX) - O (S5 IS) - O - - O O - - - -HF-DC1 O O O O O O O O O O O O

<Wireless Remote Contorol Unit>WL-DC100 - - - O O O O O - O O O

<Cables and Others>AVC-DC100 - - - - - - - O O O O OAVC-DC300 O - O O O O O - - - - -STV-250N - O - - - - - - - - - -IFC-200MC - - - - - - - - - - O OIFC-200PCS - - - - - - - - - - O OIFC-200PCU - - - - - - - - - O O OIFC-300PCU - - - - - - - O O - - -IFC-400PCU O O O O O O O - - - - -AD-PC98 - - - - - - - - - - O ODIF-100 O O O O O O O O O - - -DIF-200 - - - - - - - - - O - -DIF-B100 O O O O O O O O O - - -DIF-B250 - - - - - - - - - O - -

<All Weather Case/Waterproof Case/Waterproof Case Weight>WP-DC300 - - - - - - - - O - - -WP-DC20 - - - - - O - - - - - -WP-DC40 - - - - O - - - - - - -WP-DC1 - - O - - - - - - - - -WP-DC11 O (G7) - - - - - - - - - - -WP-DC21 O (G9) - - - - - - - - - - -WW-DC1 O - O - O O - - O - - -

G9G7

S5 ISS3 ISS2 IS

S80 G6 S70S60

S1 IS Pro1 PS G5PS G3

S50S45S40S30

G2 Pro90 IS

G1

28

3-6-2 IXY DIGITAL (The model names of IXY are for Japanese market)

2000 IS /910 IS1000900 IS810 IS800 IS

90/10WIRELESS/80/7060/55/50/40

L4

L370060030a30

L2

L500450400

320200a200

300a300

IXY DIGI-TAL

<Battery>NB-1L/1LH - - - - - O O O ONB-3L - - - O O - - - -NB-4L - O O - - - - - -NB-5L O - - - - - - - -

<Adapter/Charger>ACK300 - - - - - - - - OACK500 - - - - - O O O -ACK900 - - - O - - - - -ACK-DC10 - O - - - - - - -ACK-DC30 O - - - - - - - -CA-DC20 - - O - - - - - -CB-2L/2LE - - - - - - - - OCB-2LS/2LSE - - - - - O O O OCB-2LU/2LUE - - - O O - - - -CB-2LV/2LVE - O O - - - - - -CB-2LX/CB-2LXE O - - - - - - - -CBC-NB1 - - - - - O O O O

<DC Coupler>DR-300 - - - - - - - - ODR-500 - - - - - O O O -DR-900 - - - O - - - - -DR-10 - O - - - - - - -DR-30 O - - - - - - - -

<Speedlite>HF-DC1 O O O O O O O O O

<Wireless Remote Contorol Unit>WL-DC200 - - O - - - - - -

<Cables and Others>VC-200 - - - - - - - - OAVC-DC100 - - - O (30) O (L) O (400) - O -AVC-DC200 - - - - - - O - -AVC-DC300 O O O O (except 30) O (L2) O (500/450) - - -IFC-200PCU - - - - - - O - OIFC-300PCU - - - O (30) O (L) O (400) - O -IFC-400PCU O O O O (except 30) O (L2) O (500/450) - - -DIF-100 O O O O O O - O -DIF-200 - - - - - - O - -DIF-B100 O O O O O O - O -DIF-B250 - - - - - - O (except 200) - -

<All Weather Case/Waterproof Case/Waterproof Case Weight>AW-PS200 - - - - - - O (200) - OAW-DC10 - - - - O - - - -AW-DC30 - O (55/50/40) - - - - - - -AW-DC40 - - O - - - - - -AW-DC50 - O (60) - - - - - - -WP-DC100 - - - - - - - O (300) -WP-DC500 - - - - - - - O (300a) -WP-DC600 - - - - - - O (except 200) - -WP-DC800 - - - - - O - - -WP-DC10 - - - O (30a/30) - - - - -WP-DC70 - - - O (600) - - - - -WP-DC80 - - - O (700) - - - - -WP-DC3 - O (80) - - - - - - -WP-DC4 - O (70) - - - - - - -WP-DC5 O (800) - - - - - - - -WP-DC7 O (1000) - - - - - - - -WP-DC9 O (900) - - - - - - - -WP-DC13 - O (10) - - - - - - -WP-DC14 - O (90) - - - - - - -WP-DC15 O (810) - - - - - - - -WP-DC17 O (910) - - - - - - - -WP-DC19 O (2000) - - - - - - - -

WW-DC1 O (910/ 1000) O (80/70) - O - O O O -

29

3-6-3 PowerShot A Series

A650 IS A720 ISA710 ISA700

SX1000 ISA460A450A430A420A410A400A310

A570 ISA560A550A540A530A520A510

TX1 A640A630A620A610

A95A80

A85A75A70A60

A300A200A100

A40A30A20A10

<Battery>NB-4L - - - - O - - - - -NB4-100/NB4-200 O O O O - O O O O ONB4-300 O O O O - O O O O O

<Adapter/Charger>ACK600 O - - - - O O O - OACK800 - O O O - - - - O -ACK-DC10 - - - - O - - - - -CB-2LV/2LVE - - - - O - - - - -CB-3AH(CBK-100) O O O O - O O O O OCB-4AH(CBK4-200) O O O O - O O O O OCB-5AH(CBK4-300) O O O O - O O O O O

<DC Coupler>DR-10 - - - - O - - - - -

<Lens Accessory>WC-DC52 - - - O (except

560/550/530) - - O O - O

WC-DC58N - O - - - O - - - -WC-DC58B O - - - - - - - - -TC-DC52 - - - - - - - O - O

TC-DC52A - - - O (except 560/550/530) - - O O - O

TC-DC58N - O - - - O - - - -TC-DC58C O - - - - - - - - -

250D 52mm - - - O (except 560/550/530) - - O O - O

250D 58mm - O - - - - - - - -LA-DC52 - - - - - - - - - O (20/10)LA-DC52B - - - - - - - - - O (40/30)LA-DC52C - - - - - - - O - -LA-DC52D - - - - - - O - - -

LA-DC52F - - -O (except

570/560/550/530)

- - - - - -

LA-DC52G - - - O (570) - - - - - -LA-DC58F - - - - - O - - - -LA-DC58G - O - - - - - - - -LA-DC58J O - - - - - - - - -

<Speedlite>HF-DC1 O O O O O O O O O O

<Cables and Others>VC-100 - - - - - - - - - O (30/10)AVC-DC100 - - - - - - O (80) O (70/60) - O (40/20)

AVC-DC300 O O O (except 420/410) O - O O (95) O (85/75) - -

STV-250N - - - - O - - - - -DTC-100 (J) - - - - O - - - - -CTC-100 (except J) - - - - O - - - - -IFC-300PCU - - - - - - O (80) O (70/60) - OIFC-400PCU O O O O O O O (95) O (85/75) - -DIF-100 O O O O O O O O O ODIF-B100 O O O O O O O O O O

<All Weather Case/Waterproof Case/Waterproof Case Weight>AW-DC20 - - O (400) - - - - - - -WP-DC200 - - - - - - - - - O (20/10)WP-DC200s - - - - - - - - - OWP-DC400 - - - - - - - - O (200/100) -WP-DC700 - - - - - - - O (70/60) - -WP-DC900 - - - - - - O (80) - - -WP-DC30 - - - - - - - O (85/75) - -WP-DC50 - - - - - - O (95) - - -WP-DC60 - - - O (510/520) - - - - - -WP-DC90 - - - - - O (620/610) - - - -WP-DC2 - - - O (540) - - - - - -

30

3-6-4 Printer

*For use with Canon digital cameras and video cameras that support Canon Direct Print or PictBridge.When connecting via PictBridge with another manufacturer's camera, use the cable specified for that camera.

WP-DC6 - O (A710) - - - - - - - -WP-DC8 - - - - - O (640/630) - - - -WP-DC12 - - - O (560) - - - - - -WP-DC16 - O (A720) - - - - - - - -WP-DC18 O (A650) - - - - - - - - -

WW-DC1 O O -O (except 570/550/

530)- O O O - O

ES2ES20ES1

CP750CP730CP710CP600CP510

CP740CP720CP520CP500CP400

CP330 CP220 CP-300 CP-200 CP-100 CP-10

<Ink, paper>HC-36IP - - - - - - - - OHC-18IP - - - - - - - - OHC-18IL - - - - - - - - OKP-36IP - O O O O O O O -KL-36IP - O O O O O O O -KC-36IP - O O O O O O O -KC-18IL - O O O O O O O -KC-18IF - O O O O O O O -KW-24IP - O O O O - - - -E-P50/E-P100 O - - - - - - - -E-L50/E-L100 O - - - - - - - -E-C25 O - - - - - - - -E-C25L O - - - - - - - -E-P25BW O - - - - - - - -

<Cable>DIF-100 - - - - - - - O ODIF-200 - - - - - - - O OIFC-200PCU O* O* O* O* O* O* O* - -IFC-300PCU O* O* O* O* O* O* O* - -IFC-400PCU O* O* O* O* O* O* O* - -

<Power Supply>CA-CP100 - - - O O O O O OCBA-CP100 - - - O - O - O OCA-CP200 - O O - - - - - -CA-ES100 O - - - - - - - -NB-CP1L - - - O - O - O -NB-CP2L - O - O - O - O -NB-ES1L O - - - - - - - -

A650 IS A720 ISA710 ISA700

SX1000 ISA460A450A430A420A410A400A310

A570 ISA560A550A540A530A520A510

TX1 A640A630A620A610

A95A80

A85A75A70A60

A300A200A100

A40A30A20A10

31

4 Accessory Specifications

4-1 Main Unchanged Accessories

4-1-1 Battery and Charger Kit CBK4-300The kit consists of one NB4-300, which is a pack of four NB-3AH NiMH batteries, and one batterycharger CB-5AH/CB-5AHE.

NiMH Battery NB-3AH

Battery Charger CB-5AH/CB-5AHE

4-1-2 AC Adapter KitACK800

• Compact Power Adapter CA-PS800

Type AA NiMH battery

Nominal Voltage 1.2 V DC

Nominal Capacity 2500 mAh (min. 2300 mAh)

Battery Life (Charge Cycles) Approx. 300 times

Operating Temperatures 0 – 35°C (32 – 95°F)

Diameter x Length 14.5 x 50.0 mm (0.57 x 1.97 in.)

Weight Approx. 30 g (1.06 oz.)

Rated Input 100 – 240 V AC (50/60 Hz)16 VA (100 V) – 21 VA (240 V)

Rated Output 565 mA x 4 / 1275 mA x 2

Charging Time (a case of NB-3AH) Approx. 4 hrs. 40 min. (4 batteries)Approx. 2 hrs. (2 batteries)

Charge Indicator Charging: Orange indicator blinksFull-charge: Orange indicator lights

Operating Temperatures 0 – 35°C (32 – 95°F)Dimensions 65.0 x 105.0 x 27.5 mm (2.56 x 4.13 x 1.08 in.)Weight Approx. 95 g (3.35 oz.)

Rated Input 100 – 240 V AC (50/60 Hz), 0.18 A16 VA (100 V) – 22 VA (240 V)

Rated Output 3.15 V DC, 2.0 AOperating Temperatures 0 – 40°C (32 – 104°F)Dimensions 42.6 x 104.0 x 31.4 mm (1.68 x 4.09 x 1.24 in.)Weight Approx. 180 g (6.35 oz.) (excluding power cord)



R2: CONFIDENTIAL

TECHNICAL DESCRIPTION

CONTENTS1. Functions of each unit -------------------------------------------------------------------------------------------------------------- 1

1.1 MAIN PCB ASS'Y ---------------------------------------------------------------------------------------------------------- 11.2 DC/DC PCB ASS'Y --------------------------------------------------------------------------------------------------------- 11.3 FLASH UNIT (ST PCB ASS'Y) ------------------------------------------------------------------------------------------- 11.4 TOP FPC ASS'Y ------------------------------------------------------------------------------------------------------------- 11.5 OPERATION FPC ASS'Y -------------------------------------------------------------------------------------------------- 11.6 JOG DIAL UNIT ------------------------------------------------------------------------------------------------------------ 1

2. Troubleshooting -------------------------------------------------------------------------------------------------------------------- 22.1 When an Error Code is Displayed ----------------------------------------------------------------------------------------- 22.2 When a Problem Occurs ---------------------------------------------------------------------------------------------------- 3

3. FUSE ------------------------------------------------------------------------------------------------------------------------------- 43.1 List of Fuses Used ----------------------------------------------------------------------------------------------------------- 43.2 Positions of Fuses Used ----------------------------------------------------------------------------------------------------- 4

1

1. Functions of each unit

1.1 MAIN PCB ASS'Y1) Driving the CCD Sensor.2) Conversion of the image signal from the analog signal to the digital signal.3) Controlling the power supply and the system.4) Image processing, and reading and writing the image signal to and from the Memory card.5) Conversion of the video signal from digital to analog by LCD DRIVER.

1.2 DC/DC PCB ASS'Y1) Amplification of the video output, microphone input/audio output.2) Power supply drive (DC/DC converter).3) Battery charging control circuit.

1.3 FLASH UNIT (ST PCB ASS'Y)1) Flash drive and charging circuit.

1.4 TOP FPC ASS'Y1) Function Buttons of TOP side.

1.5 OPERATION FPC ASS'Y1) Function Buttons of REAR side.

1.6 JOG DIAL UNIT1) Function Buttons of REAR side.

1.4 TOP FPC ASS'Y

1.5 OPERATION FPC ASS'Y

1.3 ST PCB ASS'Y

1.2 DC/DC PCB ASS'Y

1.1 MAIN PCB ASS'Y1.6 JOG DIAL UNIT

2

2. Troubleshooting

2.1 When an Error Code is Displayed[Remedy]• Check for any abnormalities in the mounting of probable faulty parts or connector connections referring to the table below.• Try replacing probable faulty parts referring to the table below.[NOTE]• Error codes are displayed on the LCD Monitor.• Adjustments must be performed after the part has been replaced. For details, see the "Adjustments" chapter.

Error Code

E01

E02

E03

E04

E09

E10

E14

E16

E18

E23

Name

AE TIME OUT

AF TIME OUT

EF TIME OUT

AWB TIME OUT

JPEG DMA TIME

OUT

JPEG IC ERROR

UNKNOWN

IMAGING TIME

OUT

ZOOM LENS

ERROR

MEMORY CARD

NO SPACE

Occurrence Conditions

AE processing does not end within the specified time.

AF processing does not end within the specified time.

The focus lens is not driven.

Auto Flash Control does not end within the specified

time.

AWB processing does not end within the specified time.

JPEG processing does not end within the specified time.

JPEG compression processing does not end within

the specified time.

When an error of unknown cause occurs.

When communication between CPU and peripheral

IC is not completed within the specified time during

recording using EVF or after completion of recording.

Movement of the lens barrel does not end within

the specified time.

When the Memory Card becomes full during writing

of photographed images to Memory Card, writing

is repeatedly performed with the JPEG compression

ratio successively increased to reduce the size of the

image file until it can be successfully written to Memory

Card. This error occurs when writing of the JPEG

image file fails after 10 times.

Cause and Probable Faulty Part

MAIN PCB ASS'Y

MAIN PCB ASS'Y

OPTICAL UNIT

MAIN PCB ASS'Y

OPTICAL UNIT

MAIN PCB ASS'Y

OPTICAL UNIT

MAIN PCB ASS'Y

MAIN PCB ASS'Y

MAIN PCB ASS'Y

UNKNOWN

MAIN PCB ASS'Y

MAIN PCB ASS'Y

OPTICAL UNIT

MAIN PCB ASS'Y

MAIN PCB ASS'Y

MEMORY CARD

E24

E26

E27

POWER ON

ERROR

CAPTURE TIME

OUT

MEMORY WRITE

TIME OVER

The power of the imaging circuit on the MAIN PCB

ASS'Y is not detected.

Writing of the photographed image to SDRAM does

not end within the specified time.

Data form the buffer was not written to the Memory

Card within the specified time.

MAIN PCB ASS'Y

OPTIONAL UNIT

MAIN PCB ASS'Y

DC/DC PCB ASS'Y

E32 IS ERROR When IS-CPU or MAIN-IC does not work correctly.

MAIN PCB ASS'YE52 QUICK REVIEW

ERROR

Review of the photographed image failed.

3

2.2 When a Problem Occurs[Remedy]• Check for any abnormalities in the mounting of probable faulty parts or connector connections referring to the table below.• Make sure that the FPC connectors and the cables are properly connected and are not damaged.• Try replacing probable faulty parts referring to the table below.[NOTE]• Adjustments must be performed after the part has been replaced. For details, see the "Adjustments" chapter.

OPERATION FPC ASS'Y

MAIN PCB ASS'Y

DC/DC PCB ASS'Y

TOP COVER UNIT

FUSE(DC/DC PCB ASS'Y)

MAIN PCB ASS'Y

DC/DC PCB ASS'Y

LCD PANEL

BATTERY BOX UNIT

BATTERY COVER UNIT Damaged/Deformed

BACK LIGHT UNIT

OPERATION FPC ASS'Y

OPTICAL UNIT

MAIN PCB ASS'Y

OPTICAL UNIT

MAIN PCB ASS'Y

TOP COVER UNIT

TOP FPC ASS'Y

FLASH UNIT

MAIN PCB ASS'Y

FUSE(DC/DC PCB ASS'Y)

MAIN PCB ASS'Y

MAIN PCB ASS'Y

TOP COVER UNIT

TOP FPC ASS'Y

DC/DC PCB ASS'Y

Defect positionProblem (when an error code is not displayed) Reference

FU602(BATTERY), FU601(DC IN)

FU603

The power of the camera does not turn on.

The image is not displayed on the LCD Monitor.

The photographed image is abnormal.

The zoom does not function.

The Built-in Flash does not work.

Communications with the personal computer is

not possible.

The Memory card is not recognized.

Buttons/The Mode Dial do not work.

4

3. FUSE

3.1 List of Fuses Used

3.2 Positions of Fuses Used

DC/DC PCB ASS’Y

BATT.+FU602

FUSEDC/DCCONVERTER

VBAT

VBAT

for Flash

DIGIC IIIE1P/E20/E3 LAT

FU603FUSE

FU601

FUSEDC IN

BATTERY BOX UNIT

BATTTERMINAL BATT.+

3 fuses are used for this product.

FUSE PARTS NO.

for AC ADAPTER

for BATTERY

for FLASH UNIT

Mounted PCB NOTE

FU601

FU602

FU603

CY4-6074-000

CY4-6074-000

CY4-6081-000

DC/DC PCB ASS’Y

DC/DC PCB ASS’Y

DC/DC PCB ASS’Y

FU601R40

1

R404

CN601

L601

C60

5

C60

8

CP603 CP6

FU603FU602

403

C60

5

C60

8

ZN

R40

1

Q60

9

L606

CP601

CP602

R637

03 CP604CP613 R639

Q61

0 DC DC P.C.B. ASS'Y(PRIMARY SIDE)



R2: CONFIDENTIAL

DISASSEMBLY

For CA, USA onlyIncluded lithium battery contains Perchlorate Material - special handling may apply.See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for details.

CONTENTS1. Before Starting the Repair Work ------------------------------------------------------------------------------------------------- 1

1.1 Precautions on Flash High Voltage Circuit ------------------------------------------------------------------------------- 11.2 List of Tools ------------------------------------------------------------------------------------------------------------------ 11.3 List of Supplies -------------------------------------------------------------------------------------------------------------- 11.4 Connectors for FPC Board ------------------------------------------------------------------------------------------------- 2

2. Disassembling / Reassembling ---------------------------------------------------------------------------------------------------- 32.1 Procedure --------------------------------------------------------------------------------------------------------------------- 32.2 Separation of TOP COVER UNIT ---------------------------------------------------------------------------------------- 42.3 Separation of SIDE COVER ----------------------------------------------------------------------------------------------- 62.4 Separation of FRONT COVER UNIT ------------------------------------------------------------------------------------ 72.5 Separation of REAR COVER UNIT -------------------------------------------------------------------------------------- 92.6 Separation of JACK INNER COVER/BATTERY COVER UNIT/SPEAKER UNIT ---------------------------- 112.7 Separation of LCD UNIT ------------------------------------------------------------------------------------------------- 142.8 Disassembly of LCD UNIT ---------------------------------------------------------------------------------------------- 162.9 Separation of FLASH UNIT --------------------------------------------------------------------------------------------- 182.10 Separation of DC/DC PCB ASS'Y -------------------------------------------------------------------------------------- 222.11 Separation of OPERATION FPC ASS'Y ------------------------------------------------------------------------------- 252.12 Separation of DATA BATTERY HOLDER UNIT -------------------------------------------------------------------- 292.13 Separation of OPTICAL UNIT ------------------------------------------------------------------------------------------ 302.14 Separation of MAIN PCB ASS'Y/TOP FPC ASS'Y/BATTERY BOX UNIT ------------------------------------- 322.15 Disassembly of OPTICAL UNIT -1 ------------------------------------------------------------------------------------- 352.16 Disassembly of OPTICAL UNIT -2 ------------------------------------------------------------------------------------- 372.17 Disassembly of OPTICAL UNIT -3 ------------------------------------------------------------------------------------- 412.18 List of Screws -------------------------------------------------------------------------------------------------------------- 46

1

1. Before Starting the Repair WorkBe sure to read the following precautions before starting the repair work.

1.1 Precautions on Flash High Voltage CircuitWhen separating the FRONT COVER UNIT, be sure to discharge the MAIN CAPACITOR.

* Discharging resistor: 1 kΩ, approx. 5 W. (See Fig. 1)CAUTION:Because this is a high-voltage circuit, be careful to avoid electric shock and short-circuits with other components.

1.2 List of ToolsThe following tools are used for the re-assembling during service.List of tools

New Name of tools Part No. RemarksScrewdriver (Local Purchase)Tweezers (Local Purchase)Soldering iron (Local Purchase)

1.3 List of SuppliesThe following supplies are used for the re-assembling during service.List of supplies

New Name of supplies Part No. RemarksADHESIVE TAPE SONY T4000 CY4-6012-000 Double-sided tape (0.15mm × 6mm × 50m)DIABOND NO.1663G BLACK CY9-8129-000 Bond (200ml)LEAD FREE SOLDER RMA-98 CY9-4045-000 SolderADHESIVE TAPE, 3M NO. 56 CY4-6018-000 Electric insulation tape

Fig. 1 Precautions on Flash High Voltage Circuit

terminalST PCB

GND

MAIN CHASSIS

Dischargepoints

Electric InsulationTAPE

2

1.4 Connectors for FPC BoardThis product uses three types of connectors for the FPC board.

CAUTION:1. For the connectors of Type C and D, make sure to set them to the unlocked state before removing and

inserting the FPC board. After the FPC board is inserted, set them to the locked state.2. The FPC board is equipped with holes as shown. Use them for removal and insertion by inserting the tweezers

into them as required.

Fig. 2 Connectors for FPC board

Fig. 3 Holes for removal

LOCK

UNLOCKThe contact-pieceshould faceupwards

Unlocked state Locked state

1 Type A

3 Type C

LOCK

UNLOCKThe contact-pieceshould facedownwards

Unlocked state Locked state

4 Type D

5 Type E

Holes

The contact-pieceshould faceupwards

Unconnected state Connected state2 Type B

The contact-pieceshould facedownwards

Unconnected state Connected state

Unconnected state Connected state

3

2. Disassembling / Reassembling2.1 Procedure

(1) The following flowchart shows the disassembly procedure for PowerShot SX100 IS.(2) Reverse the disassembly procedure to reassemble them. *The pages to refer to are shown in parentheses ().

: MAIN FLOW

: SUB FLOW

: MAIN UNIT

2.4 FRONT COVER UNIT (P-7)

2.6 JACK INNER COVERBATTERY COVER UNITSPEAKER UNIT (P-11)

2.3 SIDE COVER (P-6)

2.5 REAR COVER UNIT (P-9)

2.2 TOP COVER UNIT (P-4)

2.10 DC/DC PCB ASS'Y (P-22, P-23)

2.11 OPERATION FPC ASS'Y(P-25, P-26)

2.7 LCD UNIT (P-14, P-16)

SPEAKER HOLDERBATTERY COVER SPRINGBATTERY COVER SHAFT (P-11)

JOG DIAL UNITLCD WINDOW (P-9)

JACK COVER (P-7)

MAIN-DC/DC FPCMODE DIAL TAPE (P-32)

DATA BATTERY HOLDER (P-29)

MAIN CHASSIS (P-30)

FLASH COVER UNIT (P-19)

SUB CHASSISSUB CHASSIS TAPE 1SUB CHASSIS TAPE 2SD SLOT COVER (P-26)

LCD PANELLCD PLATELCD SHEETLCD SPACERBACK LIGHT UNIT (P-16)

2.9 FLASH UNIT (P-18, P-19)

2.14 MAIN PCB ASS'YTOP FPC ASS'YBATTERY BOX UNIT (P-32)

2.12 DATA BATTERY HOLDER UNIT(P-29)

2.13 OPTICAL UNIT (P-30)

START

FRONT CAPFRONT CAP TAPE (P-35)BARRIER COVERBARRIER PLATE 1BARRIER PLATE 2BARRIER SPRINGBARREL DRIVE RING (P-37)GEAR 2GEAR 3GEAR 4GEAR 5 (P-41, P-42)

END

4

2.2 Separation of TOP COVER UNIT(1) Open the FLASH UNIT light emitting section and JACK COVER, and remove five screws on SILVER Model (a × 3,

b × 2)/BLACK Model (c × 3, d × 2).(2) Disengage the two dowels, and then detach the TOP COVER UNIT.

Note: When detaching/attaching the TOP COVER UNIT, be careful not to deform or damage the armatures.

CD3-9828-000

4.0mm

BLACKM1.7

(SELF TAP)

c

CD3-9812-000

3.5mm

BLACKM1.7

d

for BLACK Model

CD3-8993-000

4.0mm

SILVERM1.7

(SELF TAP)

a

CD3-8991-000

3.5mm

SILVERM1.7

b

for SILVER ModelNote

Armatures

Light emittingsection

(2)

TOP COVER UNIT

JACK COVER

(2)

(1)

(1)Dowel

×2

(1) - a / c

(1) - a / c

(1) - b / d

(1) - b / d

(1) - a / c

5

<Note on Reassembling>(1) Attach the TOP COVER UNIT as shown in the figure below.

Note on Reassembling (1)

Rib

Position with respect to two dowels and attach the TOPCOVER UNIT

Xe/TRIG CABLE

ST-DC/DC CABLE

Dowel×2

1. Confirmed to have installed the Xe/TRIG CABLE and ST-DC/DC CABLE on the rib.

2.

TOP COVER UNIT

6

2.3 Separation of SIDE COVER(1) Remove two screws on SILVER Model (e × 2)/BLACK Model (d × 2), and detach the SIDE COVER.

CD3-9812-000

3.5mm

BLACKM1.7

dfor BLACK Model for SILVER Model

CD3-3326-000

3.5mm

SILVERM1.7

e

SIDE COVER

(1)

(1) - d / e

7

2.4 Separation of FRONT COVER UNIT(1) Open the BATTERY COVER UNIT.(2) Remove six screws on SILVER Model (a × 3, e × 1, f × 1, g × 1)/BLACK Model (c × 3, d × 1, f × 1, g × 1), and close

the BATTERY COVER UNIT.Note: When detaching/attaching the FRONT COVER UNIT, close the BATTERY COVER UNIT.

(3) Detach the FRONT COVER UNIT and the JACK COVER.

XA4-9170-409

4.0mm

BLACKM1.7

(SELF TAP)

gXA4-9170-407

4.0mm

SILVERM1.7

(SELF TAP)

f

CD3-8993-000

4.0mm

SILVERM1.7

(SELF TAP)

afor SILVER Model

CD3-9828-000

4.0mm

BLACKM1.7

(SELF TAP)

cCD3-9812-000

3.5mm

BLACKM1.7

dCD3-3326-000

SILVERM1.7

e

3.5mm

for BLACK Model

(2) - f

(2) - g

(1)

(2)

(3) (3)

FRONT COVERUNIT

JACK COVER

BATTERY COVER UNIT

(2) - a / c(2) - a / c (2) - d / e

8

FRONT COVERUNIT

JACK COVER

ST PCB

GND

MAIN CHASSIS

ADHESIVE TAPE, 3M NO.56CY4-6018-000

(5mm x 10mm)

Note: After separating the FRONT COVER, discharge the MAIN CAPACITOR.(Because this is a high-voltage circuit, be careful to avoid electric shock and short-circuits with other components.)

<Note on Reassembling>(1) Attach the FRONT COVER UNIT as shown in the figure below.

Note

Dischargepoints

Electric InsulationTAPE

Electric Insulation TAPE


Push in.

Push in the JACK COVER, and attach the FRONT COVER UNIT while holding section A.

Section AClose the BATTERY COVER UNIT

9

2.5 Separation of REAR COVER UNIT(1) Disconnect the CN201.(2) Remove three screws on SILVER Model (a × 1, f × 1, h × 1)/BLACK Model (c × 1, f × 1, h × 1), and disengage claw

A, and then detach the REAR COVER UNIT.(3) Remove two screws (i × 2), and detach the JOG DIAL UNIT.(4) Detach the LCD WINDOW.

XA4-9170-407

4.0mm

SILVERM1.7

(SELF TAP)

fXA1-7170-207

2.0mm

SILVERM1.7

hXA4-5140-257

2.5mm

SILVERM1.4

(SELF TAP)

iCD3-8993-000

4.0mm

SILVERM1.7

(SELF TAP)

aCD3-9828-000

4.0mm

BLACKM1.7

(SELF TAP)

cfor SILVER Model for BLACK Model

Claw A

Disengage claw A.

(4)

(3)

(2)

(1)

LCD WINDOW

REAR COVERUNIT

JOG DIALUNIT

JOG DIALUNIT

CN201

(2) - h

(3) - i

(2) - f

(2) - a / c

CN201

10

<Note on Reassembling>(1) Attach the JOG DIAL UNIT as shown in the figure below.


Position with respect to three dowels and attach the JOG DIAL UNIT

Dowel

Dowel×2JOG DIALUNIT

11

2.6 Separation of JACK INNER COVER/BATTERY COVER UNIT/SPEAKERUNIT

(1) Remove one screw (f × 1), and detach the JACK INNER COVER.(2) Open the BATTERY COVER UNIT and pull out the BATTERY COVER SHAFT, and then detach the BATTERY

COVER UNIT and the BATTERY COVER SPRING.(3) Disconnect the CN102 and peel off the DOUBLE-SIDED TAPE, and then detach the SPEAKER UNIT.(4) Remove one screw (h × 1), and detach the SPEAKER HOLDER.

XA4-9170-407

4.0mm

SILVERM1.7

(SELF TAP)

fXA1-7170-207

2.0mm

SILVERM1.7

h

(2)

BATTERYCOVER

UNIT

BATTERYCOVERSHAFT

BATTERY COVERSHAFT

BATTERYCOVERSPRING

BATTERY COVERUNIT

BATTERY COVERSPRING

(2)

(2)

2.

Slide the knob1.

(1)

(2)

(2)

(4)

(3)

CN102

(3)

SPEAKER UNIT DOUBLE-SIDED TAPE(4 × 4mm)

SPEAKERHOLDER

JACK INNER COVER

Unlock and open the BATTERY COVER UNIT

(4) - h

(1) - f

12

<Note on Reassembling>(1) Attach the SPEAKER HOLDER as shown in the figure below.(2) Attach the SPEAKER UNIT as shown in the figure below.

Note on Reassembling (1) Note on Reassembling (2)

Dowel×2

Position with respect to the dowel and attach the SPEAKER HOLDER. Be careful not to pinch the DATE BATTERY CABLE.

Pass the SPEAKER CABLE through the groove of the SPEAKER HOLDER.

DATE BATTERYCABLE

SPEAKER HOLDERSPEAKER UNIT

DOUBLE-SIDEDTAPE(4 × 4mm)

SPEAKER HOLDER

SPEAKER CABLE CN102

Groove

13

(3) Attach the BATTERY COVER UNIT, BATTERY COVER SPRING and BATTERY COVER SHAFT as shown inthe figure below.


BATTERY COVERSHAFT

BATTERY COVER UNIT

BATTERY COVERSPRING

Insert.

14

2.7 Separation of LCD UNIT(1) Remove one screw (h × 1), disconnect the CN103, disengage the dowel and detach the rib.(2) Disconnect the CN4001, and detach the LCD UNIT.

XA1-7170-207

2.0mm

SILVERM1.7

h

(1)

CN103

CN4001

(2)

(2)

LCD UNIT

(1) - h

Dowel

Rib

15

<Note on Reassembling>(1) Attach the LCD UNIT as shown in the figure below.


3. Position with respect to the dowel and attach the LCD UNIT with screw.

4. Insert to CN103.

1. Insert to CN4001. CN4001

2. Insert the Rib .

Rib

Insert.

Insert.

LCD UNIT

16

2.8 Disassembly of LCD UNIT(1) Peel off the three sections A of the LCD UNIT, and detach the LDC PLATE.(2) Detach the LCD SHEET and the LCD SPACER.

Note: Reuse of the LCD SHEET is not allowed.(3) Disengage the four claws, and detach the LCD PANEL from the BACK LIGHT UNIT.

Section A

Section A(1)

(3)

LCD PLATE

LCD PANEL

LCD SHEET(DOUBLE-SIDED

TAPE is put onthe front side.)

LCD SPACER(DOUBLE-SIDED TAPEis put on the front side.)

BACK LIGHT UNIT

Claw

Claw

(2)

17

<Note on Reassembling>(1) Attach the LCD PANEL as shown in the figure below.(2) Attach the LCD SPACER as shown in the figure below.(3) Attach the LCD SHEET as shown in the figure below.



Claw×4

Disengage.

Disengage the LCD FPC, and attach the LCD PANEL on four claws of BACK LIGHT UNIT.

LCD PANEL

LCD FPC

BACK LIGHT UNITLCD PANEL+BACK LIGHT UNIT

LCD SPACER

LCD SPACERLCD SHEET

4mm±1mm

Attachment reference line

Attachment reference


Folded reference

Folded reference

Attach the LCD SPACER to the back side of the BACK LIGHT UNIT in alignment with the center position.

Align with the end of the LCD SPACER.

18

2.9 Separation of FLASH UNIT(1) Remove one screw (f × 1), disconnect the CN501 and CN602 and detach the rib, and then detach the ST PCB section.

XA4-9170-407

4.0mm

SILVERM1.7

(SELF TAP)

f

(1)

CN602

(1)

(1)

CN501

Xe/TRIGCABLE

Xe/TRIG CABLE

ST-DC/DC CABLEST -DC/DC CABLE

ST -DC/DCCABLE

TOP FPC

(1) - f

ST PCB Section

MAIN CAPACITOR

(1)

(1)Rib

Rib

19

(2) Close the light emitting section, disengage the two dowels and the hook, and then detach the Cover Open Detectswitch section of the OPERATION FPC ASS'Y.Note: Detach/attach the Cover Open Detect switch section with the light emitting section closed. (For prevention of

damage on the Cover Open Detect switch section)(3) Open the light emitting section and remove two screws (j × 2), and then detach the FLASH UNIT.(4) Remove two screws on SILVER Model (k × 2)/BLACK Model (l × 2), and detach the FLASH COVER UNIT.

XA4-5170-357

3.5mm

SILVERM1.7

(SELF TAP)

kCD3-9847-000

3.5mm

BLACKM1.7

(SELF TAP)

lCD3-8984-000

1.5mm

SILVERM1.7

NK GRIP

jfor SILVER Model for BLACK Model

Dowel

HookLight emitting sectionCover Open

Detect switch section

FLASH UNIT

FLASH COVER UNIT

OPERATION FPC ASS'Y

OPERATION FPCASS'Y

Cover Open Detect switch section

(2)

(2)

1. Close the lightemittingsection

2. Detach the FLASH COVER UNIT from the back side.

(2)

(3)

(3) - j

(3) - j

(4) - k / l

(4) - k / l

20

<Note on Reassembling>(1) Attach the FLASH COVER UNIT as shown in the figure below.


Push in.

Light emitting section

FLASH COVER UNIT

With the light emitting section closed, push in the FLASH COVER UNIT until it clicks. Open the light emitting section and fix the screws.

21

(2) Attach the Cover Open Detect switch section with the light emitting section closed.


Dowel

Dowel

Hook



Rib

Rib

Pass the ST-DC/DC CABLE and Xe/TRIG CABLE through the ribs.

CN501

CN602

Xe/TRIG CABLE

ST -DC/DCCABLE

ST -DC/DCCABLE

CN602

ST -DC/DC CABLE Xe/TRIGCABLE

TOP FPC

ST PCB section

MAIN CAPACITOR

OPERATION FPC

Cover Open Detect switchsection

Cover Open Detect switch section

With the Light emitting section closed, attach the Cover Open Detect switch section.

22

2.10 Separation of DC/DC PCB ASS'Y(1) Remove the DIABOND and the two SOLDERs, disconnect the CN401 and remove three screws (h × 3).

XA1-7170-207

2.0mm

SILVERM1.7

h

(1)

(1)

DC/DC PCB ASS'Y

CN401

(1) - h

(1) - h

SOLDER×2(DIABOND NO.1663G BLACK)

23

(2) Disconnect the CN402 (B to B) and then detach the DC/DC PCB ASS'Y.

DowelCN402 (B to B)

DC/DC PCB ASS'Y

(2)

(2)

24

<Note on Reassembling>(1) Attach the DC/DC PCB ASS'Y as shown in the figure below.


Dowel×2

CN402 (B to B)

CN401Insert the CN402 (B to B), and position with respect to two dowels and attach the DC/DC PCB ASS'Y. Insert to the CN401, and solder the CABLE.

Insert.

SOLDER

Insert.

DIABOND NO.1663G BLACK

• Provide covering to the extent of the sheath root position of each lead wire.• Be sure to cover the soldered parts completely.

DC/DC PCB ASS'Y

25

2.11 Separation of OPERATION FPC ASS'Y(1) Disconnect the CN104 and peel off the DOUBLE-SIDED TAPE, and then detach the TOP section of the OPERA-

TION FPC ASS'Y.(2) Remove three screws (f × 2, h × 1), disengage the two dowels A and the claw B, and detach the SUB CHASSIS and

OPERATION FPC ASS'Y in a subassembly form.

XA4-9170-407

4.0mm

SILVERM1.7

(SELF TAP)

fXA1-7170-207

2.0mm

SILVERM1.7

h

(1)

(1)

DATABATTERYCABLE

CN104

(2)

SUB CHASSIS/OPERATION FPC ASS'Y

(2)

(2) - f

(2) - h

Dowel A

Dowel A

Claw B

DOUBLE-SIDED TAPE (5 × 8mm)

TOP section

26

(3) Peel off the SUB CHASSIS TAPE 1 and SUB CHASSIS TAPE 2, disengage the two claws C, and then detach theOPERATION FPC ASS'Y.

(4) Disengage the two claws D, and detach the SD SLOT COVER.

(3)

(3)(3)

(3)(3)

(4)

Claw C

Claw C

Claw D

Claw D

SD SLOT COVER

SUB SHASSIS TAPE 2SUB SHASSIS

SUB SHASSIS TAPE 1

OPERATION FPCASS'Y

SUB SHASSISTAPE 2

27

<Note on Reassembling>(1) Attach the SUB CHASSIS TAPE 1 and SUB CHASSIS TAPE 2 at the respective positions shown in the figure below.(2) Attach the OPERATION FPC ASS'Y as shown in the figure below.



Position with respect to two dowels E and attach the OPERATION FPC ASS'Y on the SUB CHASSIS TAPE 2×2.

Position with respect to two claws C and attach the OPERATION FPC ASS'Y on the SUB CHASSIS TAPE 1

SUB CHASSIS

SUB CHASSIS TAPE 2

SUB CHASSISTAPE 1

OPERATION FPCASS'Y

SUB CHASSIS SUB CHASSIS

SUB CHASSIS TAPE 1 SUB CHASSIS TAPE 2

1mm

Attachment reference Attachment

reference



Align with the center position. Align with the

center position.

Dowel E×2

Claw C

Claw C

28

(3) Attach the SUB CHASSIS and OPERATION FPC ASS'Y in a subassembly form as shown in the figure below.


DATABATTERYCABLE

CN104

SUB CHASSIS/OPERATION FPC ASS'Y

Dowel A

Dowel F

Dowel A

DOUBLE-SIDED TAPE (5 × 8mm)

TOP section

3. Position with respect to the dowel and attach the SUB CHASSIS/OPERATION FPC ASS'Y to the DOUBLE-SIDED TAPE, and then insert to the CN104.

2. Insert the TOP FPC to Claw B of the SUB CHASSIS and attach the TOP FPC and SUB CHASSIS in a subassembly form

1. Position with respect to the dowel and attach the SUB CHASSIS/OPERATION FPC ASS'Y

Claw B

TOP FPC ASS'Y

SUB CHASSIS

29

2.12 Separation of DATA BATTERY HOLDER UNIT(1) Remove one screw (m × 1) and disengage the two dowels, and then detach the DATA BATTERY HOLDER UNIT.(2) Detach the DATA BATTERY HOLDER.

XA4-5170-359

3.5mm

BLACKM1.7

(SELF TAP)

m

(1)

(2)

DATA BATTERYHOLDER

DATA BATTERYHOLDER UNIT

(1) - m

Dowel

30

2.13 Separation of OPTICAL UNIT(1) Remove four screws (f × 4), disconnect the CN2000 (B to B) and CN3001 and disengage the two dowels, and then

detach the OPTICAL UNIT and MAIN CHASSIS in a subassembly form.(2) Remove two screws (n × 2) and detach the OPTICAL UNIT.

XA4-9170-407

4.0mm

SILVERM1.7

(SELF TAP)

fCD3-8930-000

1.5mm

SILVERM1.7

NK GRIP

n

Note

OPTICALFPC

OPTICAL UNIT

MAIN CHASSIS

MAIN CHASSIS

Be careful not to damage the OPTICAL FPC

(1) - f

(1) - f

(1) - f

(2)

(1) (1)

(1)

CN2000(B to B)

CN3001Dowel×2

(2) - n

31

<Note on Reassembling>(1) When attaching the OPTICAL UNIT, be careful not to damage the OPTICAL FPC.(2) Attach the OPTICAL UNIT and MAIN CHASSIS in a subassembly form as shown in the figure below.


MAIN CHASSIS

MAIN CHASSIS

OPTICAL FPCOPTICAL UNIT Dowel

Position with respect to two dowels and attach the OPTICAL UNIT and MAIN CHASSIS in a subassembly form.Insert to the CN2000 (B to B),CN3001.

Dowel

CN2000(B to B)

CN3001

32

2.14 Separation of MAIN PCB ASS'Y/TOP FPC ASS'Y/BATTERY BOX UNIT(1) Detach the MAIN PCB ASS'Y from the two dowels A.(2) Disconnect the CN1002 and CN4501, and then detach the MAIN PCB ASS'Y

Note: When detaching/attaching the MAIN PCB ASS'Y, be careful not to damage the EJECT SW.(3) Disconnect the CN1001 and detach the MAIN-DC FPC.(4) Peel off the DOUBLE-SIDED TAPE and disengage the two dowels B, and then detach the MODE DIAL TAPE and

the TOP FPC ASS'Y.

(3)

TOP FPC ASS'Y

MODE DIAL TAPE

(1)

(1)

(2)

(2)

(4)

BATTERY BOX UNIT

(4)

Dowel B

Dowel A

DowelA

DOUBLE-SIDED TAPE

CN1001

CN4501

CN1002

MAIN-DC FPC

MAIN PCB ASS'Y

EJECT SWITCH

MIC CABLE

MIC CABLE CN4501

(6 x 5mm)

33

<Note on Reassembling>(1) Attach the MODE DIAL TAPE at the respective positions shown in the figure below.(2) Attach the TOP FPC ASS'Y as shown in the figure below.(3) Attach the MAIN-DC FPC as shown in the figure below.




DC/DC PCBASS'YCN401

MAIN PCBASS'Y

CN1001

BATTERY BOX UNIT TOP FPC ASS'Y

MODE DIALTAPEMIC CABLE

TOP FPC

MODE DIAL TAPEAttach the MODE DIAL TAPE inside of ruled line of BATTERY BOX

Dowel B

DowelB

Position with respect to two dowels B and attach the TOP FPC ASS'Y by the MODE DIAL TAPEPass the TOP FPC below the MIC CABLE.

DOUBLE-SIDED TAPE

(6 × 5mm)

34

(4) Attach the MAIN PCB ASS'Y as shown in the figure below.


DowelA×2

CN1002

CN1002

MAIN-DC/DC FPC

TOP FPC

TOP FPC

EJECT SWITCH

MIC CABLE TOP PCB ASS'Y

EJECT SW

BATTERY BOX UNIT

Place the EJECT SW inside of the BATTERY BOX UNIT.

35

2.15 Disassembly of OPTICAL UNIT -1(1) Apply voltage (approx. 2.0V) to the motor terminal to extend the lens barrel until it stops.(2) Peel off the FRONT CAP TAPE and detach the FRONT CAP.

Note: Be careful not to damage the FRONT CAP.

Tweezers

Apply alcohol to the connected section and wait until alcohol is absorbed into it.And then Insert the tweezers and detach the FRONT CAP.

Lens barrel

(1)(1)

FRONT CAP

FRONT CAP TAPE

(2)

2.0V

MOTOR

36

<Note on Reassembling>(1) Attach the FRONT CAP TAPE and the FRONT CAP as shown in the figure below.


Fold

Fold

Dowel

FRONT CAP TAPE

FRONT CAP

FRONT CAP TAPE hanging to the shaded area is not allowed.Align with the dowel and attach the FRONT CAP.

37

2.16 Disassembly of OPTICAL UNIT -2(1) Disengage the two claws A and the two claws B, and detach the BARRIER COVER, BARRIER PLATE 1, BARRIER

PLATE 2, BARRIER SPRING and BARREL DRIVE RING.

(1)

Claw A

Claw A

Claw A

Claw A

Claw B

Claw B

ClawB

Claw BClaw C

Turn the BARREL DRIVE RING to position that Claw C is disengaged, and Detach the BARREL DRIVE RING.

Claw C

BARRIER PLATE 1

BARRIER PLATE 2

BARRIER PLATE 2

BARRIER COVER

BARREL DRIVE RING

BARRIER SPRING

BARRIERSPRING

Turn the BARRIER COVER in the direction of the arrow and detach it.

38

<Note on Reassembling>(1) Attach the BARREL DRIVE RING as shown in the figure below.


Claw C

Claw C

Disengage the claws C, and insert the BARREL DRIVE RING while turning in the direction of the arrow.

BARREL DRIVE RING

39

(2) Attach the BARRIER SPRING, BARRIER PLATE 2 and BARRIER PLATE 1 as shown in the figure below.


Shaft hole

Dowel

Rib

BARRIER PLATE 2

BARRIER PLATE 2

BARRIER PLATE 2

BARRIER PLATE 1BARRIER PLATE 1

BARRIER PLATE 2

SHAFT

SHAFT

BARREL DRIVE RING

BARRELDRIVE RING

BARRIERSPRING

BARRIERSPRING

BARRIERSPRING

40

(3) Attach the BARRIER COVER as shown in the figure below.


Claw D

BARRIER COVER

Insert the BARRIER COVER to positions shown in the figure below, and then turn it and set it.

Claw C

Claw B

Claw A

41

2.17 Disassembly of OPTICAL UNIT -3(1) Remove five screws (o × 5).(2) Disconnect the CN3503 and the CN3505.(3) Remove the DIABOND, and remove the three OPTICAL FPC PHOTO INTERRUPTER sections.(4) Disengage the OPTICAL FPC from seven dowels.

XA4-9140-507

5.0mm

SILVERM1.4

(SELF TAP)

o

PHOTO INTERRUPTOR section

PHOTOINTERRUPTOR

sectionPHOTO

INTERRUPTORsection

Tweezers

Tweezers Tweezers

(2)

(4)

(2)

CN3505

CN3503

OPTICAL FPC

Dowel

Dowel

(1) - o

42

(5) Disengage three dowels, and detach the CCD HOLDER section and GEARS 5, 4, 3, and 2.

(5)

(5)(5)(5)(5)

GEAR 5GEAR 4GEAR 3GEAR 2

Dowel

Dowel

Dowel

CCD HOLDER section

43

<Note on Reassembling>(1) Attach the GEARs in the direction shown in the figure in the order shown.

Note: When replacing a GEAR, replace the four GEARs as a set.


GEAR 21.

GEAR 32.

GEAR 43.

GEAR 54.

44

(2) Attach the CCD HOLDER section as shown in the figure below.


Dowel

Dowel

CCD HOLDER section

Dowel

45

(3) Attach the OPTICAL FPC as shown in the figure below.

Note on Reassembling (3) PHOTOINTERRUPTOR section

DIABOND No.1663G BLACK

PHOTOINTERRUPTOR section

PHOTOINTERRUPTOR section

DIABONDNo.1663G BLACK

DIABONDNo.1663G BLACK

CN3505

CN3503

OPTICAL FPC

Dowel

46

2.18 List of Screws

XA4-9170-409

4.0mm

BLACKM1.7

(SELF TAP)

gXA4-9170-407

4.0mm

SILVERM1.7

(SELF TAP)

fXA1-7170-207

2.0mm

SILVERM1.7

h

XA4-5140-257

2.5mm

SILVERM1.4

(SELF TAP)

iXA4-5170-357

3.5mm

SILVERM1.7

(SELF TAP)

kCD3-9847-000

3.5mm

BLACKM1.7

(SELF TAP)

l

XA4-5170-359

3.5mm

BLACKM1.7

(SELF TAP)

m

CD3-8993-000

4.0mm

SILVERM1.7

(SELF TAP)for SILVER Model

aCD3-9828-000

4.0mm

BLACKM1.7

(SELF TAP)for BLACK Model

cCD3-8991-000

3.5mm

SILVERM1.7

for SILVER Model

bCD3-9812-000

3.5mm

BLACKM1.7

for BLACK Model

d

3.5mm

CD3-3326-000

SILVERM1.7

for SILVER Model

e

CD3-8984-000

1.5mm

SILVERM1.7

NK GRIP

j

CD3-8930-000

1.5mm

SILVERM1.7

NK GRIP

nXA4-9140-507

5.0mm

SILVERM1.4

(SELF TAP)

o



R2: CONFIDENTIAL

ADJUSTMENT

CONTENTS1. Replacement Parts and Adjustment Items --------------------------------------------------------------------------------------- 12. Adjustment Tools ------------------------------------------------------------------------------------------------------------------- 23. Before Starting Electrical Adjustments ------------------------------------------------------------------------------------------ 3

3.1 TWAIN Driver Installation --------------------------------------------------------------------------------------------------- 33.2 Canon DCP Connect Installation ------------------------------------------------------------------------------------------ 33.3 Adjustment Software Installation ------------------------------------------------------------------------------------------ 33.4 Preparation ------------------------------------------------------------------------------------------------------------------- 53.5 Starting up the Adjustment Software -------------------------------------------------------------------------------------- 63.6 Menu Window---------------------------------------------------------------------------------------------------------------- 63.7 How to Use the Adjustment Software ------------------------------------------------------------------------------------- 7

4. Calibration --------------------------------------------------------------------------------------------------------------------------- 84.1 Calibration -------------------------------------------------------------------------------------------------------------------- 8

5. Adjustment Procedure ----------------------------------------------------------------------------------------------------------- 125.1 IS 1 Adjustment ------------------------------------------------------------------------------------------------------------ 125.2 IS 2 Adjustment ------------------------------------------------------------------------------------------------------------ 225.3 Optical Unit Adjustment -------------------------------------------------------------------------------------------------- 235.4 CCD Adjustment ----------------------------------------------------------------------------------------------------------- 255.5 Imaging Process Adjustment --------------------------------------------------------------------------------------------- 285.6 Color Adjustment ---------------------------------------------------------------------------------------------------------- 315.7 Shading Adjustment ------------------------------------------------------------------------------------------------------- 335.8 Pixel Dot Adjustment ----------------------------------------------------------------------------------------------------- 355.9 LCD Adjustment ----------------------------------------------------------------------------------------------------------- 375.10 Flash Adjustment ---------------------------------------------------------------------------------------------------------- 385.11 Checking of sound recording/output ------------------------------------------------------------------------------------ 40

1

1. Replacement Parts and Adjustment ItemsPowerShot SX100 IS requires electrical adjustments when certain parts are replaced.The table below indicates the adjustments required for the respective part replacements.For all other parts not listed below, no electrical adjustments are necessary after replacement.

: Adjustment is necessary after replacement. : Adjustment is necessary after replacement.

(Adjustment is not necessary, only if the adjustment data has been saved and then transferred after the part is replaced.)Blank : Adjustment is unnecessary.

* When OPTICAL UNIT is replaced, adjust certainly at the procedure as below.

#1. IS Adjustment

#2. Optical Unit Adjustment

#3. CCD Adjustment

#4. Imaging Process Adjustment

#5. Color Adjustment

#6. Shading Adjustment

#7. Pixel Dot Adjustment

#8. Flash Adjustment

OPTICAL UNIT

FINDER/FLASH UNIT

MAIN PCB ASS’Y

DC/DC PCB ASS’Y

LCD UNIT

#1 #2 #3 #5 #7 #8#6

OpticalUnit

Adjust-ment

CCDAdjust-ment

LCDAdjust-ment

ImagingProcessAdjust-ment

ColorAdjust-ment

ShadingAdjust-ment

Pixel DotAdjust-ment

FlashAdjust-ment

IS 1Adjust-ment

IS 2Adjust-ment

#4

AdjustmentItems

Replacement Part

2

2. Adjustment ToolsThe following tools are required for electrical adjustment.

*1 2pcs. required.*2 -100 : 100~120V, -200 : 200~240V*3 The file containing "How to print out" and Chart for print-out is in folder of the Adjustment Software.

DESCRIPTION

PC/AT-Compatible Machine(Windows 2000 pre-installed Model, USB port)

SERVICE MANUAL

ADJUSTMENT SOFTWARE

Compact Power Adapter CA-PS800

AC Cable

INTERFACE CABLE IFC-400PCU

Brightness Box

Color Viewer (5500˚K)

Color Bar Chart

18% Gray Chart

AF Chart (1)

Infinity Collimator

W-10 Filter *1

C-12 Filter

FL-W Filter

ND-4 Filter

Light-Shielding Cloth (500 x 500 mm or larger)

Tripod

Reference Camera

DIGITAL CAMERA SolutionDisk

PARTS NO.

—

—

—

—

—

—

CY9-1566-100/200*2

CY9-1562-100/200*2

DY9-2002-000

CY9-1563-000

CY9-1583-000

CY9-1569-100/200*2

CY9-1556-000

CY9-1555-000

CY9-1557-000

CY9-1553-000

—

—

—

—

—

REMARKS

Local purchase

Download

Download

Enclosed in"AC Adapter Kit ACK800"

Enclosed in"AC Adapter Kit ACK800"

Enclosed in Merchandise

*

*

3

IS Chart (1) 3

Local purchase

Local purchase

Merchandise

Enclosed in Merchandise

3

3. Before Starting Electrical Adjustments

3.1 TWAIN Driver InstallationInstall the USB Driver for Adjustment in the CD-ROM to PC.("This Adjustment Software" is impossible when the RS-232C TWAIN driver is used.)

3.2 Canon DCP Connect InstallationAfter downloading and extracting Adjustment Software, double-click Setup.exe (\Canon DCPConnect\Setup.exe) to install it.

3.3 Adjustment Software Installation1. After downloading and extracting Adjustment Software, double-click Setup.exe to install it.

(Adjustment Softwares are different according to the model of camera that you are going to adjust.)2. When the dialog box below appears, click the "OK" button.

4

3. When the dialog box below appears, click the button. (Software installation will then begin.)

4. When the dialog box below appears, click the "Continue" button.(In the case that you do not add a shortcut on desktop, remove clicking from the check box.)

5

OPTICAL UNIT

2727

3.4 PreparationBefore starting up the Adjustment Software, follow the preparatory steps below:

1. Obtain all the tools necessary for the adjustment.2. For the Optical Unit Adjustment jot down the data written on the optical Unit.

You will need it later.

3. Connect the Camera to the Power Source with the AC Adapter Kit ACK800 (CA-PS800 & AC Cable).4. Set the Replay Mode on the camera.5. Connect the Camera’s Digital terminal to the PC’s USB Port with INTERFACE CABLE IFC-400 PCU.

6. Turn on the camera while pressing the left side of the cross key and the Print/Share button.Note: Perform the preparation in the following order otherwise the camera won’t work properly.

CAMERA BODY

USB

DIGITAL

INTERFACE CABLEIFC-400PCU

Compact Power AdapterCA-PS800

Personal Computer

6

3.5 Starting up the Adjustment SoftwareAfter completing the preparatory steps, click Start and move the cursor to Program; then select CanonDigital Camera Adjustment and click Canon PowerShot A720 IS Adjustment.

3.6 Menu WindowWhen the Adjustment Software starts up, the Menu Window below will appear.

7

3.7 How to Use the Adjustment Software! Start-up of Camera Watch

This camera requires Camera Watch for the communication with PC. Start up Camera Watch by selectingStart > Program > Canon Utilities > Camera DCP connect > Camera Watch.

! Mode changeThis camera uses normally PTP for communication with PC. Because calibration and adjustment become impossible dependingon the condition of PTP, select the TWAIN mode of the PTP before starting calibration and adjustment.• "FA" button: This button is used to change the mode from the USER mode to the FA mode.

(PTP to TWAIN)* Before starting calibration and adjustment, be sure to set the FA mode.• "USER" button: This button is used to change the mode from the FA mode to the USER mode.

(TWAIN to PTP)* When calibration and adjustment are completed, be sure to change the mode to the USER mode before quitting the software.

! Model Name Change <Select Model>Model Name can be changed. Language, Date Style and Video Type are also changed to initial settings that are compatible withModel Name.* Be sure to change Model Name every time MAIN PCB ASS'Y is changed.

! Adjustment Menu/CalibrationFor starting, click the button related with calibration/adjustment.* Whenever you use your light source for the adjustment for the first time, be sure to click the "Calibration" Button.

! Quitting the Adjustment SoftwareClick the "Exit" button.

! Camera Data Saving and Loading <Data Transfer>• "Save" button : This button saves all adjustment data stored on the camera in text format.• "Load" button : This button loads all adjustment data saved in text format to the camera.

! Calibration Data Saving and Loading <Calibration>• "Save" button : This button saves the calibration data.• "Load" button : This button loads the saved calibration data to the adjustment software and reflects it.

! Notes• If the adjustment fails, a message indicating the failure will appear on each product. If this happens, do the adjustment

again.• The Adjustment Software is dedicated only to Canon Digital Camera PowerShot SX100 IS.

Never use it for any other camera.• The Windows2000 must be pre-installed on the computer that is equipped with the USB terminal.* Operations on the other Operating Systems such as Windows95, 98, Windows XP and others are not guaranteed.

8

4. Calibration

4.1 Calibration! Tools Used• Personal Computer• SERVICE MANUAL• ADJUSTMENT SOFTWARE• Compact Power Adapter CA-PS800• AC Cable

• INTERFACE CABLE IFC-400PCU• Brightness Box• Color Viewer (5500°K)• Color Bar Chart• W-10 Filter (2pcs.)

• C-12 Filter• FL-W Filter• ND-4 Filter• Light-Shielding Cloth• Reference Camera• DIGITAL CAMERA SolutionDisk

Click the "Calibration" button.

When the message on the right appears, go to 4.

1

2

3

1. When the message on the right appears, check that the reference camera (Merchandise) is connected to the computer.

2. Click the "OK" button.

9

Brightness Box

Personal Computer

PowerSource

CAMERABODY

Light Shielding Cloth

Brightness Box

Personal Computer

PowerSource

W-10 Filter

4

5 When the message on the right appears, go to 6.

6


1. Set the filter of the Brightness Box and place the camera so that lens is set against the light source surface of the Brightness Box.

2. Put the light-Shielding Cloth so that light ex-cept the Brightness Box does not come in.

3. Set the Brightness Box to the value displayed on the message.

4. Click the "ADJUST" button.

1. Place the camera so that lens is set against the light source surface of the Brightness Box via the two W-10 Filters.




CAMERABODY

10

8


10Color Viewer

Personal Computer

Power Source

Stand

11

CAMERABODY

Brightness Box

Personal Computer

Power Source

C-12 Filter

FL-W Filter

CAMERABODY

ND-4 Filter

1. Shift a frame on the displayed screen with a mouse to choose a color of color bar.

2. Click the "Sampling" button.

1. Remove the two W-10 Filters. 2. Place the camera so that lens is set against the

light source surface of the Brightness Box via the C-12 and FL-W Filter.




1. Attach the Color Bar Chart to the Color Viewer.

2. Place the camera so that the Viewing image ofthe color bar chart is the full of LCD with the ND-4 Filter attached.


Color Bar Chart

11

12 Check "Save as the Reference" and click the "OK" button to store the data.

13 When the message on the right appears, click the "FINISH" button. (This ends the "Calibration" Adjustment.)

12

5. Adjustment Procedure

5.1 IS 1 Adjustment! Tools Used• Personal Computer• SERVICE MANUAL• ADJUSTMENT SOFTWARE• Compact Power Adapter CA-PS800• AC Cable

• INTERFACE CABLEIFC-400PCU

• IS Chart (1)• Tripod• DIGITAL CAMERA SolutionDisk

1 Click the "IS" button.

2

3IS Chart (1)

CAMERABODY

PersonalComputer

PowerSource

Tripod

176.5cm

1. Set IS Chart (1) 176.5cm away from the front of Canon logo of the camera. Adjust the position of the chart so that the center of the chart is displayed in the center of the LCD.


When the message on the right appears, input the numbers written on the Optical Unit into the "Focus Sink" text box, then click the "Update" button. When "Update" is completed, click the "ADJUST" button.

13

4 Check if the chart appears in the center on the PC monitor and there is no problem, click the "ADJUST" button.

5 Mark the center of the chart on the Monitor and click the "ADJUST" button.


14

7 If the center of the chart is roughly in the middle of the two markings, click the "OK" button.Otherwise, change the value of "Pitch Offset", click the "ADJUST" button and redo the adjust-ment.

8 When the message on the right appears, click the "ADJUST" button.


* This step sets the tentative offset value in order to perform the Pitch Gain adjustment.

15


11


If the center of the chart is roughly in the middle of the two markings, click the "OK" button.Otherwise, change the value of "Yaw Offset", click the "ADJUST" button and redo the adjust-ment.* This step sets the tentative offset value in order

to perform the Yaw Gain adjustment.

16



15 If the distance between the two markings is six scales on the chart, click the "OK" button.Otherwise, change the value of "Pitch Gain" until the distance between the two markings becomes six scales on chart, click the "ADJUST" button and repeat the steps 13 to 15.

17


17 Mark the center of the chart on the Monitor and click the"ADJUST" button.


18

19 If the distance between the two markings is six scales on the chart, click the "OK" button.Otherwise, change the value of "Yaw Gain" until the distance between the two markings becomes six scales on chart, click the "ADJUST" button and repeat the steps 17 to 19.



19


23 If the center of the chart is roughly in the middle of the two markings, click the "OK" button.Otherwise, change the value of "Pitch Offset", click the "ADJUST" button and redo the adjust-ment.


20



27 If the center of the chart is roughly in the middle of the two markings, click the "OK" button.Otherwise, change the value of "Yaw Offset", click the "ADJUST" button and redo the adjust-ment.

21

28 When the message on the right appears, click the "FINISH" button.(This ends the IS 1 adjustment.)

22

5.2 IS 2 Adjustment! Tools Used

• Personal Computer• SERVICE MANUAL• ADJUSTMENT SOFTWARE• Compact Power Adapter CA-PS800

• AC Cable• INTERFACE CABLE

IFC-400PCU• DIGITAL CAMERA SolutionDisk

1 Click the "IS 2" button.


3 When the message on the right appears, click the "FINISH" button.(This ends the IS 2 adjustment.)

23

5.3 Optical Unit Adjustment! Tools Used

• Personal Computer• SERVICE MANUAL• ADJUSTMENT SOFTWARE• Compact Power Adapter CA-PS800

• AC Cable• INTERFACE CABLE

IFC-400PCU• AF Chart (1)

• Infinity Colimator• Tripod• DIGITAL CAMERA SolutionDisk

1 Click the "Optical Unit" button.

3 When the message on the right appears, proceed to step4.


24

7 When the message on the right appears, click the "FINISH" button. (This ends the "Optical Unit" Adjustment.)


6 1. Set the AF Chart (1) (CY9-1583-000) at 104.0cm away from the front of the Canon logo. * Set the AF Chart (1) (CY9-1583-000) on a

plain color wall or equivalent. * Adjust the light so that the brightness of the

chart will be about EV9.0. The ray of the light should come in at a narrow angle as seen from the chart.

2. Adjust the position of the camera finely so that the center of the AF Chart (1) (CY9-1583-000) is aligned with the center of the LCD.


4 1. Place the camera at the infinity collimator. 2. Adjust the position of the camera finely so that

the center of the Auto Focus Chart is aligned with the center of the LCD.


AF Chart (1)

CAMERABODY

Personal Computer

Power Source

Tripod

104.0cm

Linghtingabout 15 degrees

CAMERABODY

Infinity Collimator

Personal Computer

Power Source

25

5.4 CCD Adjustment! Tools Used

• Personal Computer• SERVICE MANUAL• ADJUSTMENT SOFTWARE• Compact Power Adapter CA-PS800• AC Cable


• Brightness box• Light-Shielding Cloth• DIGITAL CAMERA SolutionDisk

1 Click the "CCD" button.


3 1. Set the filter of the Brightness Box and place the camera so that lens is set against the light source surface of the Brightness Box.

2. Put the light-Shielding Cloth so that light except the Brightness Box does not come in.


4. Click the "ADJUST" button. * When the adjustment does not work, click

the "Default" button.

Brightness Box

Personal Computer

PowerSource

CAMERABODY


26

4

5

1. When the message on the right appears, set to the displayed value.

2. Click the "Adjust" button.

1. When the message on the right appears, set to the displayed value.


6 1. When the message on the right appears, set to the displayed value.


7 1. When the message on the right appears, set to the displayed value.


27

8 1. When the message on the right appears, go to 9.

9

10 When the message on the right appears, click the "FINISH" button. (This ends the "CCD" Adjustment.)

1. Cover the camera with the Light-Shielding Cloth so that the no light reasons the CCD.

2. Click the "ADJUST" button. CAMERABODY

PowerSource

PersonalComputer


28

5.5 Imaging Process Adjustment! Tools Used



• Brightness Box• W-10 Filter (2pcs.)• C-12 Filter

• FL-W Filter• Light-Shielding Cloth• DIGITAL CAMERA SolutionDisk

1

2

3

Click the "Imaging Process" button.


1. Set the filter of the Brightness Box and place the camera so that lens is set against the light source surface of the Brightness Box.




Brightness Box

Personal Computer

PowerSource

CAMERABODY


29

5



7

Brightness Box

Personal Computer

PowerSource

W-10 Filter

CAMERABODY

CAMERABODY

Brightness Box

Personal Computer

Power Source

C-12 Filter

FL-W Filter

1. Place the camera so that lens is set against the light source surface of the Brightness Box via the two W-10 Filters.




1. Remove the two W-10 Filters. 2. Place the camera so that lens is set against the

light source surface of the Brightness Box via the C-12 and FL-W Filter.




30

8 When the message on the right appears, click the "FINISH" button. (This ends the "Imaging Process" Adjustment.)

31

5.6 Color Adjustment! Tools Used



• Color Viewer (5500°K)• Color Bar Chart• ND-4 Filter• DIGITAL CAMERA SolutionDisk

1 Click the "Shading" button.


3Brightness Box

Personal Computer

PowerSource

CAMERABODY


1. Do not set the filter of the Brightness Box and place the camera so that lens is set about 3mm interval from the light source surface of the Brightness Box.




32

5

4

6

7 When the message on the right appears, click the "FINISH" button. (This ends the "Color" Adjustment.)

1. Shift a frame on the displayed screen with a mouse to choose a color of color bar.

2. Click the "Sampling" button.

1 .Confirm to see that the image on the PC monitor satisfies the specifications.

2. If the image on the PC monitor does not satisfy the specifications, change the data using UP, DOWN button or change the data directly by typing the data in the text box. Then click the "UPDATE" button.

If these data within specifications, click the "OK" button.

Measure the yellow and red colors, and if they are both within the specifications, click the "OK" button, and then proceed to step 7.

* Specification Ave_Cr = Reference Camera ± 10 Ave_Cb = Reference Camera ± 10

33

5.7 Shading Adjustment! Tools Used



• Brightness Box• Light-Shielding Cloth• DIGITAL CAMERA SolutionDisk

1 Click the "Shading" button.


3Brightness Box

Personal Computer

PowerSource

CAMERABODY


1. Do not set the filter of the Brightness Box and place the camera so that lens is set about 3mm interval from the light source surface of the Brightness Box.




34

4 When the message on the right appears, click the "FINISH" button. (This ends the "Shading" Adjustment.)

35

5.8 Pixel Dot Adjustment! Tools Used



• Brightness Box• Light-Shielding Cloth• DIGITAL CAMERA SolutionDisk

1

2

3 1. Set the filter of the Brightness Box and place the camera so that lens is set against the light source surface of the Brightness Box.




Brightness Box

Personal Computer

PowerSource

CAMERABODY


In this adjustment, the temperature inside the camera needs to be above a certain temperature. If the internal temperature is below this certain temperature, the camera will repeat zooming operations to raise the temperature. An error will occur if this adjustment is performed before the temperature reaches this standard temperature. Perform the adjustment again in such a case.

Click the "Pixel Dot" button.


36


5

6 When the message on the right appears, click the "FINISH" button. (This ends the "Pixel Dot" Adjustment.)

CAMERABODY

PowerSource

PersonalComputer


1. Cover the camera with the Light-Shielding Cloth so that the no light reasons the CCD.


37

5.9 LCD Adjustment! Tools Used



• Reference Camera• DIGITAL CAMERA SolutionDisk

! Preparation1. Insert the blank SD Card into the reference camera.2. Connect the reference camera with the PC.3. Add the "Gray.jpeg" image to the SD Card of the refernce camera using Zoom Browser EX.

(Gray.jpg is in the folder of Adjustment Software downloaded.)4. Finish the ZoomBrowser EX.5. Disconnect the reference camera from the PC, and display the "Gray.jpg" image in PLAY mode.

1 Click the "LCD" button.

2 1. Compare the image with that of the reference camera. If it has a different color tint, adjust it by repeating clicking the Yellow/Blue button and the "Update" button alternately.

2. Click the "FINISH" button. (This ends the "LCD" Adjustment.)

38

5.10 Flash Adjustment! Tools Used



• 18% Gray Chart• Tripod• DIGITAL CAMERA SolutionDisk

1 Click the "Flash" button.


3 1. Set the 18% Gray Chart at 41.5cm away from the front of the Canon logo.

2. Make the room as dark as a darkroom. 3. Click the "ADJUST" button.

PersonalComputer

Power Source

18% Gray Chart

41.5cm

CAMERABODY

Tripod

39

4 When the message on the right appears, click the "FINISH" button. (This ends the "Flash" Adjustment.)

40

5.11 Checking of sound recording/outputIt is not required to adjust the recording/output (volume, etc.) of sound.Check the camera if the sound is recorded/play-backed properly.



R2: CONFIDENTIAL

DIAGRAMS

CONTENTS1. INTERCONNECTION DIAGRAM2. P.C.B. DIAGRAMS

2.1 MAIN PCB ASS’Y (Primary Side)2.2 MAIN PCB ASS’Y (Secondary Side)2.3 OPERATION FPC ASS’Y (Primary Side)2.4 DC/DC PCB ASS’Y (Primary Side)2.5 DC/DC PCB ASS’Y (Secondary Side)2.6 OPTICAL FPC ASS’Y (Primary Side)2.7 ST PCB ASS’Y (Secondary Side)2.8 TOP FPC ASS’Y (Primary Side)

01 Sep. 2007 CANON INC., 2007

1. INTERCONNECTION DIAGRAM

: :

LCD UNIT

DATA BATTERYHOLDER UNIT

MAIN CAPACITOR

JOG DIAL UNIT

TOP FPC ASS’Y

OPERATION FPC ASS’Y

FLASH UNIT

MAIN-DC FPC

DC/DC PCB ASS’Y

ST PCB ASS’Y

+−BLACK RED

+−

Solder

SW103FLASH OPENDETECT SW

MENUSW105

DISP.SW104

FACE CATCHSW102

PRINTSW101

Metal contact (Pins’ face up)Metal contact (Pins’ face down)

Metal contact Metal contact

OPTICAL UNIT

SPEAKER UNITCN

401

CN602

SW402PLAY

SW401EXPOSURE

SW201TELE/WIDE

SW203SHUTTER

SW202POWER

LED401

IC602

CN402

CN601

CN403

IC601

IC5001

IC5002

IC5003

CN10

01

CN1002

CN1004

SW1001BATTERY/SD CARD

Cover Open Detect SW

IC1001

IC1002

IC1003

IC1004

IC1005

IC1006IC1007

IC1008

IC3001

IC3201

IC4001

CN1003

CN2000

IC4501

CN45

01

IC4502

IC2000

IC2001

IC2002

IC2003

IC2004

IC2005

CN30

01

CN4001

CN101

CN102

CN103

CN10

4

IC501

CN501

LED201POWER

CN201

MAIN PCB ASS’Y

BATTERY BOX UNITCN2500

+

−BLACK

RED

MICROPHONE

01 Aug. 2007 CANON INC., 2007

2. P.C.B. DIAGRAMS2.1 MAIN PCB ASS’Y (Primary Side)

AAAAA

AA

AA

A

R3224

C4001C4002

C400

3

C4005C4006

C4007

C4008

C4009

C401

0

C4011C401

2

C4013

C401

4C4

015

C401

7

C4018

L1008

L100

9

R400

5

ZD10

01ZD

1002

ZD1003

C5001 C5002

C5003

C5004

R5001 R5002

R5003 R5004

R5005

R500

6

R5007 R5008

IC5001IC5002

IC5003CN

1001

CN10

02

CN10

04

CN10

05

C1005

C100

7

C1008

C1009

Q1008

C1010 C1011

L300

1

C1012C1013

C1014

C101

5

Q1012

C101

6

C1017

C1018

C1019

L320

1

SW10

01

C102

0

Z3201

C102

1

Z320

2

C1022C102

3C1

024

D1001

NF10

01

C102

5

C102

6

C1027

C1028

C102

9

R100

8

C1030

IC1001

R1009

C103

1

C103

2

IC1002

IC1003

C1033

IC10

04

IC1005

C103

5

C1036

IC1006

IC1007

C103

7

C103

8

IC1008

C103

9

R101

3

R1014

R101

5

R101

8

C1040

TH10

01

C104

2

C1043

C1044

C1045

C1046

C1048

C1049

R102

4

R1025

R102

6

R102

7

R102

8

R1029

C1051

C105

2

C105

3

C105

4

C105

5

C105

6

C105

7

R1030

C1058

R1031

C105

9

R103

2

R103

3

R103

4

R1035

R103

6

R103

7

R103

8

C1060

R103

9

C1061

C106

2

C1063

C1064

C1065

C1066

R104

0

R1042

R1043

R1044

R1046

R104

7

R1048

R1049

R1050

R105

1

R105

2R1053R1054

R1055

R105

6

R1057

R105

8

R1059 R1060

R1063

RA1002

RA1003 RA1004

ZD4001

RA1005

C205

8

C3002

C3003

C300

4C3

005

C3006

C3007

C3008

C300

9

C320

1

C320

2

C320

3

C3204C3

011

C3206

C3012

C320

7

C320

8C321

0C3

211

C321

4

C321

5C3

216

C321

7

C3218

C321

9

R300

1R3

002

R3003

C322

0

R3004

C3221

C322

2

C3223C3224

C322

5

IC3001

C3226

C3227

C3228

C3229

R320

4R3

205

R3206

R3207

C3230

R3208R3209

IC3201

C3231C3232

C3233

C3234

X1001

C3235

X100

2

C3236

R3210

R3211

R3212

R3213

R3214

R3215

R3216

R321

7

R3218

R3219

R3220

R322

1R3

222

R3223

IC4001

R1064

R102

3

R101

9

C100

6

Q1006

R102

0

ZNR1

001

DA1003

SR1001

48MH

z 27MHz

CP

32

10

CP3211

C P 4 0 0 1

C P 4 0 0 2

C P 4 0 0 3

C P 4 0 0 4

C P 4 0 0 5

C P 4 0 0 6C P 4 0 0 7 C P 4 0 0 8

C P 4 0 0 9 C P 4 0 1 0

C P 4 0 1 1

C P 4 0 1 2

C P 1 0 0 1

C P 1 0 0 2

C P 1 0 0 3

C P 1 0 0 4

C P 1 0 0 5

C P 1 0 0 6

C P 1 0 0 7

C P 1 0 0 8

C P 1 0 0 9

C P 1 0 1 0

C P 1 0 1 1

C P 1 0 1 2

C P 1 0 1 3

C P 1 0 1 4

C P 1 0 1 6

C P 1 0 1 7

C P 1 0 2 0

C P 1 0 2 1 C P 1 0 2 2

C P 1 0 2 3 C P 1 0 2 4

C P 1 0 2 5 C P 1 0 2 6

C P 1 0 2 7 C P 1 0 2 8

C P 1 0 2 9

C P 1 0 3 0

C P 1 0 3 1

CP1032

C P 1 0 3 3

C P 1 0 3 4

C P 1 0 3 5

C P 1 0 3 6

C P 1 0 3 7

C P 1 0 3 8

C P 1 0 3 9

C P 1 0 4 0

C P 1 0 4 1 C P 1 0 4 2

C P 1 0 4 3

C P 1 0 4 4

C P 4 5 0 1

C P 1 0 4 5

C P 1 0 4 6

CP

10

47

C P 1 0 4 8CP

10

49

C P 1 0 5 0

CP

10

51

C P 1 0 5 2

C P 1 0 5 3

CP

10

54

C P 1 0 5 5

CP

10

56

C P 1 0 5 7

C P 1 0 5 8

C P 1 0 5 9

C P 2 0 0 0

C P 1 0 6 0

C P 2 0 0 1

C P 1 0 6 1

C P 2 0 0 2

C P 1 0 6 2

C P 2 0 0 3

C P 1 0 6 3

C P 1 0 6 5

C P 1 0 6 6

C P 3 0 0 3

C P 3 0 0 4

C P 3 0 0 5

C P 3 0 0 6

C P 3 0 0 7

C P 3 0 0 8

C P 3 0 0 9CP3201

CP3202

CP3203

CP3204

CP3205

CP3206

CP3207

CP3208

C P 3 2 0 9

C P 1 0 6 7

C P 1 0 6 8

C P 1 0 6 9

01 Aug. 2007 CANON INC., 2007

2.2 MAIN PCB ASS’Y (Secondary Side)

C4019

L1001

R4003

R4004

L4501

L2000

L2001

L2002

CN1003

C1001

C1002

C1003 C1004

Q100

1

Q100

2

Q1003

Q1004

Q1005

Q1007

Q1009

Q1010

Q1011

R1001R1002

R1003

R1004

R1005

R1006

R1007

C1034

R1010

CN4501

R1011

R1012

R1016

R1017

C1041

C4501

C4503

C1047

C4504

C4505

R1021

C4506

R1022

C4507C4508C4509

C1050

C4510

CN2000

C4511 C4512

C4513

C4515

C4516

C4517

C4518

C4519

C2000

C2001

C2002C2003

C4520

Q2000

C2004

C2005

Q2001

C2006

Q2002

C2007

Q200

3

C2008

C2009

R4501

R1045

C2011

R4506

C2012

C2013

C2014

IC4501

IC4502

C2016

C2017

C2018

C2019

R4511

C2020

C2021

C2022

C2023

D2000

C2025

C2027

R2000

C2028

C2029

C2030

IC2000

IC2001

C2031

C2032

IC2002

C2033

IC2003

C2034

IC2004

C2035

IC2005

C2036

C2037

C2038

R2011

C2039

R2012

R2013

R2014

R2015

R2017

R2018

C2040

RA1001

C2042

C2043

C2044

C2045 R2020

R2022

R2024

R2026

R2027

CN3001

R2030

R2031

C2059

R2032

R2033

R2034

R2035

R2036

C2060

C2061

R2041

R2042

R2043

R2044

R2045

R2046

R3005R3006

R3007R3008

R3009R3010

R3011R3012

RA2002

RA2003

CN4001

R2047

Q2004

C2062

C4016

DA1001

D 1 0 0 3

CP2004

C P 2 0 0 5

C P 2 0 0 6

C P 2 0 0 9

C P 2 0 1 0

C P 2 0 1 1

C P 2 0 1 2

CP

20

27

01 Aug. 2007 CANON INC., 2007

2.3 OPERATION FPC ASS’Y (Primary Side)

LE

D1

01

SW

10

1

SW

10

2

SW103

SW

10

4

SW

10

5

CN

10

1

CN102

CN103

CN

10

4

01 Aug. 2007 CANON INC., 2007

2.4 DC/DC PCB ASS’Y (Primary Side)

R401

R 4 0 2 R 4 0 3

R 4 0 4

R405

R 6 0 1

R 6 0 2

R 6 0 3

R604

R 6 0 5

R606

R607

R608

R 6 0 9

R 6 1 0

R 6 1 1

CN40

2

R 6 1 2

R613

R 6 1 4

R615

R616

R 6 1 7

R618

R619

C N 6 0 1

R 6 2 0

R 6 2 1

R622

R 6 2 3

R 6 2 4

R625

R 6 2 7

R628

R 6 3 1

R 6 3 5

R 6 3 7

R 6 3 9

C 6 0 1

C 6 0 2

C603

C604

R 6 4 0

R 6 4 1

C605

C 6 0 6

R 6 4 2

C607

C608

C 6 0 9

C610

C611

C612

C613

C614

C 6 1 5

C616

C 6 1 7

C618

C 6 1 9

C620

C 6 2 1

C622

C623

C 6 2 4

C 6 2 5

C 6 2 6

C 6 2 7

C 6 2 8

C629

C630

C 6 3 1

C 6 3 2 C 6 3 3

C 6 3 4

C635

C636

C 6 3 7C 6 3 8

C639 C 6 4 1

ZN

R4

01

D601

D602D603

D604

I C 6 0 1

IC602

T 6 0 1

D A 4 0 1

D A 4 0 2

FU60

1

FU60

2

F U 6 0 3

ZD40

1

Q 6 0 1

Q 6 0 2

Q603

Q604

Q605

Q 6 0 6

Q6

07

Q608

Q609

Q610

L 6 0 1

L 6 0 2

L 6 0 3

L 6 0 4

L 6 0 5

L 6 0 6

L 6 0 7

L 6 0 8

L609

L 6 1 0

L 6 1 1

L613L6

14

C N 4 0 3

C P 6 0 1

C P 6 0 2

C P 6 0 3 C P 6 0 4

C P 6 0 5

C P 6 0 6

C P 6 0 7

C P 6 0 8

C P 6 0 9

C P 6 1 0C P 6 1 1

C P 6 1 2

C P 6 1 3

C P 6 1 4

C P 6 1 5

C P 6 1 6

C P 6 1 7

C P 6 1 8

01 Aug. 2007 CANON INC., 2007

2.5 DC/DC PCB ASS’Y (Secondary Side)

CN401C N 6 0 2

L E D 4 0 1

SW401SW402

01 Aug. 2007 CANON INC., 2007

2.6 OPTICAL FPC ASS’Y (Primary Side)

LED3501

CN3504

CN

35

05

TH3501

PS

35

01

PS

35

02

PS

35

03

PS

35

04

CN

35

01

CN

35

02

CN3503

01 Aug. 2007 CANON INC., 2007

2.7 ST PCB ASS’Y (Secondary Side)

Q501

Q5

02

Q5

03

Q5

04

L5

01

TB501

TB502

TB503

TB504TB505 TB506

TB507

TB508

R5

01

R502

R5

03

R504R505

R5

06

R507

R5

08

R509

R5

10

R5

11

R512

R5

13

R514

R5

15

C5

01

C5

02

C5

03

C5

04

C5

05

C5

06

C507

C5

08

D501

D5

02

IC

50

1

T501

CN501

CP504

CP509 CP505

CP508CP501

CP502

CP507

CP503

CP506

01 Aug. 2007 CANON INC., 2007

2.8 TOP FPC ASS’Y (Primary Side)

CN201

D2

01

D202

D2

03

D2

05

D2

06

D207D208

D2

09

D2

10

D2

11

LED201

SW201

SW203

SW202

(1/2)

Model: Digital IXUS 960 IS PowerShot SX100 IS

Ref No.: AJ-0566EUR Date: December 2007

Location: Firmware Subject: Firmware changes (to prevent date setting from being reset) Detail: 1. Changes The firmware has been updated to fix the malfunction in the camera’s date setting that is sometimes reset when restarting the camera. Digital IXUS 960 IS Old New

For Service: GM1.00C GM1.00D For Users: 1.0.0.0 1.0.0.0

PowerShot SX100 IS

Old New For Service: GM1.00B GM1.00C For Users: 1.0.0.0 1.0.0.0

Product Quality Classification Number (Fifth digit from the left in the serial number)

Digital IXUS 960 IS: Changed from 0 to 1 PowerShot SX100 IS: Changed from 1 to 2 2. Timing of change The firmware change has been made from early November 2007 production. 3. Repair information Please check the firmware version when repairing, and update it to the latest version. 1) How to update the firmware Please refer to the ReadMe included in the update file. 2) How to check the main PCB ass’y firmware If the PCB classification mark is the one shown in the chart below or later, the firmware version is as follows. Digital IXUS 960 IS: GM1.00D PowerShot SX100 IS: GM1.00C

Service Bulletin DIGITAL CAMERA

SOFTWAREIssued by Canon Europa N.V.

AJ-0566EUR

(2/2)

Model Digital IXUS 960 IS PowerShot SX100 IS Front of the main PCB

Firmware versions GM1.00C GM1.00D GM1.00B GM1.00C Firmware PCB classification mark 5 or later 3 or later How to check PCB classification mark

PCB classification mark on the PCB connector (See above illustration) Check second digit from the left.

PCB classification mark on the PCB connector (See above illustration) Check second digit from the left.

4. Parts control information 1) Changed Post-countermeasure parts will be stocked sequentially. Digital IXUS 960 IS CM1-4310-000 PCB ASS’Y MAIN PowerShot SX100 IS CM1-4274-000 PCB ASS’Y MAIN

CANON INC., 2007

PARTS CATALOG

C

PowerShot SX100 IS

R2:CONFIDENTIAL

Trademarks:Canon Inc.’s trademark, logos, product names, service marks and those trademark, logos, product names,service marks licensed to Canon Inc. by any of its affiliate or subsidiary are registered or unregisteredmarks of Canon Inc. or such affiliate or subsidiary in Japan and/or other countries.Adobe, the Adobe logo, Acrobat, the Acrobat logo and Reader are either registered trademarks or trade-marks of Adobe Systems Incorporated in the United States of America and/or other countries.All other trademarks, product names, service marks are generally either registered or unregistered marksof their respective owners.

Copyright:All copyrights in the content of this Parts Catalog are owned or controlled by Canon Inc. You are notpermitted to copy, reproduce, download, modify, adapt or translate in any way the content of this PartsCatalog for any purpose other than the purpose contemplated herein without prior written consent ofCanon Inc.

CONTENTSPowerShot SX100 IS

Casing Parts ----------------------------------------------------------------------------------------------------------------------Pg1Internal Parts ---------------------------------------------------------------------------------------------------------------------Pg2Optical Unit ----------------------------------------------------------------------------------------------------------------------Pg3Fuse ---------------------------------------------------------------------------------------------------------------------------Pg4

Accessories-1 ------------------------------------------------------------------------------------------------------------------------Pg5Accessories-2 ------------------------------------------------------------------------------------------------------------------------Pg6Service Tools-1 ----------------------------------------------------------------------------------------------------------------------Pg7Service Tools-2 ----------------------------------------------------------------------------------------------------------------------Pg8

CAUTION

Especially critical parts in the power circuit block should not be replaced with other marks.

Critical parts are marked with in this parts list.

Category of CLASS

A: Frequency of use: High

B: Frequency of use: Middle

C: Frequency of use: Low

D: Safety-related critical parts

E: Consumable parts

F: Standard screws and washers

S: Supply of the parts is limited

Y: Service Tools

PowerShot SX100 IS

Casing PartsPg1

102 x2

102 x2

104 x2

106 x2

101 x2

101

103

103

102

103

102

105

105

105

102

2

8

9

1

6

4

7

3

10

11 12

13

15

16

17

19

18

14

See Pg2

5

PowerShot SX100 IS

PARTS LIST

NEW SYMBOL PARTS NO. CLASS QTY DESCRIPTION REMARKS* 1 CM1-4158-000 B 1 COVER UNIT, FRONT, SILVER* CM1-4447-000 B 1 COVER UNIT, FRONT, BLACK* 2 CM1-4156-000 B 1 COVER UNIT, BATTERY, SILVER* CM1-4445-000 B 1 COVER UNIT, BATTERY, BLACK* 3 CD3-8932-000 C 1 SPRING, BATTERY COVER

* 4 CD3-8931-000 C 1 SHAFT, BATTERY COVER* 5 CD3-8923-000 C 1 COVER, JACK, INNER, SILVER* CD3-9821-000 C 1 COVER, JACK, INNER, BLACK* 6 CD3-8922-000 B 1 COVER, JACK, SILVER* CD3-9820-000 B 1 COVER, JACK, BLACK

* 7 CM1-4159-000 B 1 COVER UNIT, TOP, SILVER* CM1-4448-000 B 1 COVER UNIT, TOP, BLACK* 8 CM1-4283-000 C 1 SPEAKER UNIT* 9 CD3-8985-000 C 1 HOLDER, SPEAKER* 10 CM1-4163-000 B 1 JOG DIAL UNIT, SILVER

Pg1

* CM1-4450-000 B 1 JOG DIAL UNIT, BLACK* 11 CM1-4157-000 B 1 COVER UNIT, REAR, SILVER* CM1-4446-000 B 1 COVER UNIT, REAR, BLACK* 12 CD3-8921-000 B 1 WINDOW, LCD* 13 CY1-6737-000 C 1 PLATE, BODY NUMBER, SILVER 13011*****

* CY1-6738-000 C 1 PLATE, BODY NUMBER, BLACK 13011****** 14 CD3-8969-000 B 1 COVER, SIDE, SILVER* CD3-9802-000 B 1 COVER, SIDE, BLACK* 15 CD3-8927-000 C 1 PLATE, LCD* 16 CK9-1288-000 B 1 PANEL, LCD

* CK9-1288-001 B 1 PANEL, LCD (SELECTION)* 17 CM1-4154-000 C 1 BACK LIGHT UNIT* 18 CD3-8929-000 C 1 SPACER, LCD* 19 CD3-8928-000 C 1 SHEET, LCD

101 CD3-3326-000 3 SCREW (SILVER model)

* CD3-9812-000 3 SCREW BLACK (BLACK model)* 102 CD3-8993-000 7 SCREW (SILVER model)* CD3-9828-000 7 SCREW BLACK (BLACK model)

103 XA4-9170-407 3 SCREW* 104 CD3-8991-000 2 SCREW (SILVER model)

* CD3-9812-000 2 SCREW BLACK (BLACK model)105 XA1-7170-207 3 SCREW106 XA4-5140-257 2 SCREW

PowerShot SX100 IS

Internal PartsPg2

3

4

5

2

1

6

8

9

103 x2104 x2

102 x2

101 x2

105 x3

11

12

14

13

10

7

C

AA

105106

102

102

102

102

102

AA

ABAC

AB

N.Sl : N.S Stand for No Stock

N.S

See Pg3

N.S

PowerShot SX100 IS

PARTS LIST

NEW SYMBOL PARTS NO. CLASS QTY DESCRIPTION REMARKS* 1 CM1-4155-000 B 1 BATTERY BOX UNIT, SILVER* CM1-4444-000 B 1 BATTERY BOX UNIT, BLACK* 2 CD3-8938-000 C 1 TAPE, MODE DIAL* 3 CM1-4282-000 C 1 FPC ASS'Y, TOP* 4 CK1-1654-000 C 1 FPC, MAIN-DC

* 5 CM1-4274-000 C 1 PCB ASS'Y, MAIN* 6 CM1-4169-000 B 1 FLASH UNIT, SILVER* CM1-4451-000 B 1 FLASH UNIT, BLACK* 7 CM1-4516-000 B 1 COVER UNIT, FLASH, SILVER* CM1-4517-000 B 1 COVER UNIT, FLASH, BLACK

* 8 CM1-4275-000 C 1 PCB ASS'Y, DC/DC* 9 CM1-4281-000 C 1 FPC ASS'Y, OPERATION* 10 CD3-8939-000 C 1 TAPE, SUB CHASSIS 1* 11 CD3-8926-000 C 1 COVER, SD SLOT* 12 CD3-8934-000 C 2 TAPE, SUB CHASSIS 2

Pg2

* 13 CM1-4161-000 C 1 HOLDER UNIT, DATA BATT, SILVER* CM1-4449-000 C 1 HOLDER UNIT, DATA BATT, BLACK* 14 CD3-8987-000 B 1 HOLDER, DATA BATTERY, SILVER* CD3-9808-000 B 1 HOLDER, DATA BATTERY, BLACK* 101 CD3-8930-000 2 SCREW NK GRIP

102 XA4-9170-407 7 SCREW* 103 CD3-8984-000 2 SCREW NK GRIP* 104 CD3-9847-000 2 SCREW BLACK (BLACK model)

XA4-5170-357 2 SCREW (SILVER model)105 XA1-7170-207 4 SCREW

106 XA4-5170-359 1 SCREW BLACK

PowerShot SX100 IS

Optical UnitPg3

7

1


N.S

N.S

8

5

910

1211

76

43

2

101 x5

PowerShot SX100 IS

PARTS LIST

NEW SYMBOL PARTS NO. CLASS QTY DESCRIPTION REMARKS* 1 CY1-6735-000 B 1 OPTICAL UNIT, SILVER* CY1-6736-000 B 1 OPTICAL UNIT, BLACK* 2 CD3-8835-000 B 1 CAP, FRONT, SILVER* CD3-9840-000 B 1 CAP, FRONT, BLACK* 3 CD3-8834-000 C 1 TAPE, FRONT CAP SIZE (010)

Pg3

* 4 CD3-8832-000 C 1 COVER, BARRIER, SILVER* CD3-9839-000 C 1 COVER, BARRIER, BLACK* 5 CD3-8831-000 C 2 PLATE, BARRIER 1, SILVER* CD3-9838-000 C 2 PLATE, BARRIER 1, BLACK* 6 CD3-8830-000 C 2 PLATE, BARRIER 2, SILVER

* CD3-9837-000 C 2 PLATE, BARRIER 2, BLACK* 7 CD3-8833-000 C 2 SPRING, BARRIER* 8 CY1-6774-000 C 1 RING, BARRIER DRIVE* 9 CY1-6741-000 C 1 GEAR, 4* 10 CY1-6742-000 C 1 GEAR, 5

* 11 CY1-6740-000 C 1 GEAR, 3* 12 CY1-6739-000 C 1 GEAR, 2

101 XA4-5170-359 5 SCREW

PowerShot SX100 ISPg4 Fuse

FU601

R40

1

R404

CN601

L601

C60

5

C60

8

CP603 CP6

FU603

FU602

C60

5

C60

8

ZNR

401

9

L606

CP601

CP602

R637

03 CP604CP613 R639

610 DC/DC P.C.B. ASS'Y

(PRIMARY SIDE)

3!

1!

2!

PowerShot SX100 IS

PARTS LIST

NEW SYMBOL PARTS NO. CLASS QTY DESCRIPTION REMARKSPg4

1 CY4-6074-000 D 1 FUSE, MATSU. DENKI UNHS206 FU6012 CY4-6074-000 D 1 FUSE, MATSU. DENKI UNHS206 FU6023 CY4-6081-000 C 1 FUSE, MATSU. DENKI UNHS203 FU603

PowerShot SX100 IS

Accessories-1Pg5


N.S

N.S

N.S

N.S

N.S

1

USB Interface CableIFC-400PCU

AV Cable AVC-DC300 Alkaline Batteries (X2)Canon Digital CameraSolution Disk

Wrist Strap WS-200 SD Memory Card SDC-16M

PowerShot SX100 IS

PARTS LIST


1 C84-1060-000 B 1 STRAP, WRIST WS-200

PowerShot SX100 IS

Accessories-2Pg6

AC Cable

PLUG TYPE

1

65

43

2

N.S

Compact Power AdapterCA-PS800

NiMH Battery NB4-300

Battery Charger CB-5AH/CB5AHE

N.S

N.S

N.S : N.S Stand for No Stock

PowerShot SX100 IS

PARTS LIST


1 D82-0641-000 C 1 CABLE, AC, JAPAN FOR JAPAN2 WT3-5063-000 C 1 CABLE, AC, USA FOR USA, CANADA3 D82-0643-000 C 1 CABLE, AC, EUROPE FOR EUROPE, ASIA4 D82-0644-000 C 1 CABLE, AC, UK FOR ASIA5 D82-0645-001 C 1 CABLE, AC, AUSTRALIA FOR AUSTRALIA

6 WT3-5087-000 C 1 CABLE, AC, CHINA FOR CHINA

PowerShot SX100 IS

Service Tools-1Pg7

Adhesive Tape SONY T4000(Double-side Tape)

2

Diabond NO.1663G Black

1

Lead Free Solder RMA-98

3

PowerShot SX100 IS

PARTS LIST

NEW SYMBOL PARTS NO. CLASS QTY DESCRIPTION REMARKS1 CY9-8129-000 Y 1 BOND, DIABOND NO.1663G BLACK2 CY4-6012-000 Y 1 ADHESIVE TAPE, SONY T4000 6mm x 50m roll3 CY9-4045-000 Y 1 SOLDER, LEAD FREE RMA-98

Pg7

PowerShot SX100 IS

Service Tools-2Pg8

18% Gray ChartColor Viewer (5500˚K) Standard Color Bar Chart

AF Chart (1)

Brightness BoxInfinity Collimator

2

1

3

10

5

C-12 FilterW-10 FilterFL-W FilterND-4 Filter

6

78

9

IS Chart (1)4

N.S

PowerShot SX100 IS

PARTS LIST

NEW SYMBOL PARTS NO. CLASS QTY DESCRIPTION REMARKS1 CY9-1562-100 Y 1 COLOR VIEWER 5500K FOR 100~120V AC

CY9-1562-200 Y 1 COLOR VIEWER 5500K FOR 200~240V AC2 DY9-2002-000 Y 1 COLOR BAR CHART3 CY9-1563-000 Y 1 CHART, 18% GRAY4 CY9-1583-000 Y 1 CHART, AF (1)

5 CY9-1569-100 Y 1 COLLIMATOR, INFINITY FOR 100~120V ACCY9-1569-200 Y 1 COLLIMATOR, INFINITY FOR 200~240V AC

6 CY9-1555-000 Y 1 FILTER, C-12 (58 MM)7 CY9-1556-000 Y 2 FILTER, W-10 (58 MM)8 CY9-1557-000 Y 1 FILTER, FL-W (58 MM)

9 CY9-1553-000 Y 1 FILTER, ND-4 (58 MM)10 CY9-1566-100 Y 1 BRIGHTNESS BOX FOR 100~120V AC

CY9-1566-200 Y 1 BRIGHTNESS BOX FOR 200~240V AC

Pg8

canon powershot sx100is

Documents

exposed metallic parts

ac cord

critical parts

leakage current hot

service marks

jumpered ac plug

leakage current cold

metallic overlays