catalogue 10 euro nh3

Issue 10 Valid from 2010-09-01

Product catalogue 10

www.samon.se tel: +46 - 40 - 155859 fax: +46 - 40 - 156031 Catalogue 10 EURO 1008.doc page 3 (31)

Table of contents: Overview detectors / measuring principles ......................................................................................................................................................... 4

Monitoring units................................................................................................................................................................................................... 6

Single point unit, SPU.................................................................................................................................................................................... 6 Single point unit, G27C.................................................................................................................................................................................. 6 Multipoint unit, MPU (2, 4 or 6 channels) ...................................................................................................................................................... 7 Multi channel units, (12 DI or 24 DI) .............................................................................................................................................................. 8

Gas analyser, Sampling system (NDIR) for NH3, HFC or CO2.......................................................................................................................... 9

Monitoring units, others..................................................................................................................................................................................... 10

(NH3) detection of ammonia in water and brine ................................................................................................................................................ 11

(NH3) detector for ammonia, with relay output.................................................................................................................................................. 12

(NH3) detector for ammonia, for connection to monitoring unit......................................................................................................................... 13

(NH3) detector for ammonia, transmitter (4-20mA) ........................................................................................................................................... 14

(NH3) detector for ammonia, (ATEX) ................................................................................................................................................................ 15

(HFC) detector, with relay output ...................................................................................................................................................................... 16

(HFC) detector, for connection to monitoring unit ............................................................................................................................................. 17

(HFC) detector, transmitter (4-20mA) ............................................................................................................................................................... 18

(HFC) detector in ATEX-classified spaces........................................................................................................................................................ 18

(HFC) detector for room monitoring (hotels, offices etc)................................................................................................................................... 18

Exhaust gas (VOC) detector for garages, with relay output ............................................................................................................................. 19

Exhaust gas detector for (CO) and (NO2), transmitter (4-20mA / 0-10V) ......................................................................................................... 20

Flammable and explosive gas detector, with relay output ................................................................................................................................ 21

Flammable and explosive gas detector, for connection to monitoring unit ....................................................................................................... 22

Flammable and explosive gas detector, transmitter (4-20mA) ......................................................................................................................... 23

Flammable and explosive gas detector, (ATEX) .............................................................................................................................................. 23

(CO2) carbon dioxide detector, with relay output .............................................................................................................................................. 24

(CO2) carbon dioxide detector, for connection to monitoring unit ..................................................................................................................... 24

(CO2) carbon dioxide detector, transmitter (4-20mA / 0-10V)........................................................................................................................... 25

(CO2) carbon dioxide detector, Other ............................................................................................................................................................... 26

(O2) detector for oxygen.................................................................................................................................................................................... 27

(O2) detector for oxygen, (ATEX)...................................................................................................................................................................... 27

Portable detectors............................................................................................................................................................................................. 28

Auxiliary equipment........................................................................................................................................................................................... 29

Service tools ................................................................................................................................................................................................ 31

Options, Service and Commissioning............................................................................................................................................................... 31

Terms and conditions of sale............................................................................................................................................................................ 31



Overview detectors / measuring principles

Detectors for Ammonia (NH3)

Measuring principle Standard range Types Output

Semi conductive 0-10000 ppm Gx230-NH3, Gx24-NH3 Three relays

GJ-EX-NH3 Depending on monitoring unit

MP-series Depending on monitoring unit

Chemosorption CS21-NH3 4-20mA

Charge carrier inject. 30-200 ppm CI21-200 4-20mA

30-1000 ppm CI21-1000 4-20mA

30-10000 ppm CI21-10000 4-20mA

Catalytic 0-40000 ppm (4%) CC28-NH3 4-20mA

Electrochemical 0-1000 ppm EC28-NH3 4-20mA

IR absorption (NDIR) 0-25000 ppm IR-em2 (8 ch) / IR-em2 (16 ch) One (1) DO / channel. Two alarm relays and fault relay

Detectors for refrigerant as HFC (HCFC, CFC) and mixtures The HFC detector is also used for HCFC and CFC gas.


Semi conductive 0-4000 ppm Gx230-HFC, Gx24-HFC Three relays


0-5000 ppm RM-serie One relay

Chemosorption CS21-HFC 4-20mA

IR absorption (NDIR) 0-25000 ppm IR-em2 (8 ch) / IR-em2 (16 ch) One (1) DO / channel. Two alarm relays and fault relay

Detectors for flammable Hydrocarbon gases (HC) as propane (LPG), methane etc


Semi conductive / 0-40% LEL GS230-HC, GS24-HC Three relays

GJ-EX-HC Depending on monitoring unit

MP-DS-HC Depending on monitoring unit

Chemosorption 0-50% LEL CS21-Methane 4-20mA

Catalytic 0-100% LEL TR5200-DC 4-20mA

Detectors for carbon dioxide (CO2) Measuring principle Standard range Types Output

Infrared absorption (NDIR) 0-10 000 ppm GS230-CO2, GS24-CO2, GSLT24-CO2 Three relays

0-10 000 ppm MP-D-.., MP-DS-.., MPDS-LT-CO2 Depending on monitoring unit

0-10 000 ppm TR-IR-CO2, TR-IR-CO2 LT 4-20mA / 0-10 V

0-5000, (0-30000) ppm aSense (Room mounting IP21, IP54) 4-20mA / (0-10V), relay

UG-aSense (Duct mounting) 4-20mA / (0-10V), relay

LT-aSense (Freezing rooms IP54) 4-20mA / (0-10V), relay



Overview detectors / measuring principles

Detectors for Oxygen (O2)


Electrochemical 0-30% GMA36 Pro Three relays

0-25% EC 28 EX 4-20mA

Detectors for Carbon monoxide (CO) / Exhaust gas (VOC) Measuring principle Standard range Types Output

Semi-conductive (0-200 ppm) Gx230-AQS, Gx24-AQS Three relays


Electrochemical 0-300 ppm TR-EC-CO 4-20 mA / 0-10 V

Detector for Nitrogen dioxide (NO2)


Electrochemical 0-10 ppm TR-EC-NO2 4-20 mA / 0-10 V



Monitoring units Single point unit, SPU - SPU is a monitoring unit for one single channel (detector) - Microprocessor controlled unit with LED status indication and three alarm levels. - Alarm delay in four steps and Manual/auto alarm reset - Built-in service function and self test program. - Three alarm relays with 230 volt / 5A rated SPDT contacts. - Built-in audible alarm - Optional battery back-up - Option, on special order the unit can be delivered with pre-set alarm levels for specific gases. Remote detector option: MP-D (room mounting, IP21), MP-DS (room mounting, IP54), MP-DR (Pressure relief valves), MP-DK (duct mount), GJ-EX (ATEX classified) and detectors with 4-20 mA or 0-10 V output signal. Order code Model Description PG EURO

SPU

20-355 SPU-230 230VAC A *)

20-350 SPU-24 12-24V AC/DC A *)

60-300 Pre-set alarm levels Net 25

*) Price on request. Expected delivery from fall 2010. Single point unit, G27C - G27C is a single channel unit for DIN-rail mounting. - The unit has LED status indication for two alarm thresholds and a fault condition. - Manual/auto alarm reset. - Built-in alarm test function. - Three alarm relays with 24 volt / 1A rated SPST contacts. - Fault alarm with failsafe relay operation on loss of power. - Option, on special order the unit can be delivered with pre-set alarm levels for specific gases. Remote detector option: G(x)2.0-series and GJ-EX (ATEX classified). Order code Model Description PG EURO

G27C

20-200 G27C 12VAC/DC A 335

60-300 Pre-set alarm levels (per detector) Net 25

NEW!



Multipoint unit, MPU (2, 4 or 6 channels) - The MPU2C, MPU4C and MPU6C are monitoring units for two, four and six detectors. - Microprocessor controlled unit with independent Channel LED status indication and with three independent alarm

thresholds per channel. - Alarm delay in four steps and Manual/auto alarm reset for each channel. - Built-in service function and self test program. - Four alarm relays with 230 volt / 5A rated SPDT contacts. - Failsafe relay operation on loss of power. - Built-in audible alarm - Optional battery back-up - 24VDC/150mA output for external buzzer or flashlight. - Option, on special order the unit can be delivered with pre-set alarm levels for specific gases. 1) Remote detector option: MP-D (room mounting, IP21), MP-DS (room mounting, IP54), MP-DR (Pressure relief valves), MP-DK (duct mount), GJ-EX (ATEX classified) and detectors with 4-20 mA or 0-10 V output signal. Order code Model Description PG EURO

MPU

20-310 MPU2C 2 channels, 230VAC/24VDC NEW! A 746

20-300 MPU4C 4 channels, 230VAC/24VDC A 1019

20-305 MPU6C 6 channels, 230VAC/24VDC A 1281

60-300 Pre-set alarm levels (per detector) 1) Net 25

Factory settings: Detector type Range Alarm levels NH3 -1000 0 – 1000 ppm 150 / 300 / 500 ppm NH3 - 4000 0 – 4000 ppm 150 / 500 / 3000 ppm HFC 2) 0 – 4000 ppm 100 / 1000 / 2000 CO2 0 – 10000 ppm 2000 / 2000 / 5000ppm Flammable / explosive gas 0 – 40% LEL 5 / 10 / 20% LEL 2) Normal standard calibration is for R134a. The HFC detector is also used for HCFC and CFC.



Monitoring units Multi channel units, (12 DI or 24 DI) - LAN63-PKT and LAN63/64-PKT are monitoring units for detectors with relay outputs. - Totally eight LAN64 slaves can be connected to one LAN63 master panel, which gives 108 DI in total. - The units have LED indication and optional time delay for each digital input. - Each input can be set up as A or B-alarm. - Two alarm relays, A or B, with 24 volt / 1A rated SPDT contacts. - Failsafe relay operation on loss of power. - Manual alarm reset. Remote detector option: G(x)2.0-series and G(x)24/230-series. Order code Model Description PG EURO

LAN63-PKT

81-100 LAN63-PKT 12 DI, 230 VAC, IP32 A 478

LAN63/64-PKT

81-200 LAN63/64-PKT 24 DI, 230 VAC, IP32 A 744

81-110 LAN63 Only alarmpanel, 12 DI, 24 VAC, Master A 369

81-120 LAN64 Only alarmpanel, 12 DI, 24 VAC, Slave A 361

LAN65

Relay box for LAN63-PKT and LAN63/64-PKT

81-130 LAN65 Relay box, 12 DI, 24 VAC, A 698



Gas analyser, Sampling system (NDIR) for NH3, HFC or CO2 IR-em2, Sampling system using Infra Red absorption - Detects HCFC’s, HFC’s, Carbon dioxide (CO2) or Ammonia (NH3) - Monitors up to 16 zones - Simple 6 key user interface with password Protection - Individual zone naming and alarm thresholds - Historic data and alarm logs - Optional fail-safe alarm operation - Self diagnostics detect system faults - Highly selective to minimise nuisance alarms Order code Model Description PG EURO

IR-em2

82-112 IR-em2 (8ch) HFC Aspirated 8 Channel HCFC/HFC unit E *)

82-122 IR-em2 (16ch) HFC Aspirated 16 Channel HCFC/HFC unit E *)

82-115 IR-em2 (8ch) NH3 Aspirated 8 Channel Ammonia unit E *)

82-125 IR-em2 (16ch) NH3 Aspirated 16 Channel Ammonia unit E *)

- IR-em2 (8ch) CO2 Aspirated 16 Channel CO2 unit E *)

- IR-em2 (16ch) CO2 Aspirated 16 Channel CO2 unit E *)

Accessories - Sample tube Supplied in 100m drums in 16 colours E *)

- End of line filter E *)

- Inline Filter E *)

- 2 Way Manifold E *)

- 4 Way Manifold E *)

- VIEWPOINT “Black box” which generates HTML pages which can be viewed via a web browser. E *)

- Strobe Interface panel 24 volt output for siren/flashlight E *)

- Sample tube filter Internal air filter E *)

- Sample tube lenses E *)

- Side panel filter Dust filter for cabinet E *)

- Air pump, replacement E *)

- Relay Alarm Panel E *)

*) Price on request

NEW!



Monitoring units, others

Order code Model Description PG EURO

GMA 40 1-4 channel unit with display Designed for DIN-rail mounting Output 4-20mA (GMA41) Four relays for alarm and fault. Remote detector option: CS21, CI21 etc.

83-110 GMA 41 1 channel, 230VAC/24VDC C *)




GMA 80 1-8 channel unit with display Wall mounting Output 4-20mA (GMA81) Four relays for alarm and fault. Remote detector option: CS21, CI21 etc.

83-210 GMA 81 1 channel, 230VAC C *)

83-211 GMA 83 3 channel, 230VAC C *)

83-212 GMA 84 4 channel, 230VAC C *)

83-213 GMA 88 8 channel, 230VAC C *)

*) Price on request



(NH3) detection of ammonia in water and brine

- Designed for monitoring of Ammonia in secondary cooling circuits. - Media: Water, Brine mixtures, e.g. Ethylene, Tyfoxit, Hycool etc. Order code Model Description PG EURO

MiniCal

Output, 2 x 4-20mA. Measuring range: - NH3 0,2 - 100ppm (option 0-10ppm) - NH4 0,2 - 100ppm (option 0-10ppm) Power supply: Controller 24V DC, Pump 230V AC. Pressure range 1.. 6 bars. (option up to 10 bar) Temperature range (in circuit) -30…+80oC. Stainless steel IP65

35-181 MiniCal II Open system C *)

35-180 MiniCal III Pressurised system C *)

*) Price on request



(NH3) detector for ammonia, with relay output

- Microprocessor controlled unit with built-in service mode, self-test and ”Fail-safe” function. - Three alarm levels with relays (230V / 5A) - The units can be interfaced with monitoring unit LAN63-PKT, LAN63/64-PKT or to other equipment which accepts a volt

free relay inputs - Ambient temperature: -40oC...+50oC - Humidity: 0… 95% Rh (none condensing) Order code Model Description PG EURO

GD Room mounting 160x80x60 mm IP21

37-255 GD230-NH3-1000 0-1000 ppm, 230 VAC A 518

37-257 GD230-NH3-4000 0-4000 ppm, 230 VAC A 518

37-250 GD24-NH3-1000 0-1000 ppm, 12-24 VAC/DC A 494

37-252 GD24-NH3-4000 0-4000 ppm, 12-24 VAC/DC A 494

GS Splash proof, room mounting 160x130x60mm IP54

37-455 GS230-NH3-1000 0-1000 ppm, 230 VAC A 623

37-457 GS230-NH3-4000 0-4000 ppm, 230 VAC A 623

37-450 GS24-NH3-1000 0-1000 ppm, 12-24 VAC/DC A 599

37-452 GS24-NH3-4000 0-4000 ppm, 12-24 VAC/DC A 599

GSR Splash proof, room mounting with remote sensor, 5m cable 160x130x60mm IP54

37-955 GSR230-NH3-1000 0-1000 ppm, 230 VAC A 659

37-957 GSR230-NH3-4000 0-4000 ppm, 230 VAC A 659

37-950 GSR24-NH3-1000 0-1000 ppm, 12-24 VAC/DC A 635

37-952 GSR24-NH3-4000 0-4000 ppm, 12-24 VAC/DC A 635

GK Detector for duct mounting with 1,5m cable 160x80x60 mm IP54

37-855 GK230-NH3-1000 0-1000 ppm, 230 VAC A 659

37-857 GK230-NH3-4000 0-4000 ppm, 230 VAC A 659

37-850 GK24-NH3-1000 0-1000 ppm, 12-24 VAC/DC A 635

37-852 GK24-NH3-4000 0-4000 ppm, 12-24 VAC/DC A 635

GR Detector specially designed for vent lines from pressure relief valves in refrigeration plants. Standard cable length 1,5m. 160x80x60 mm IP54

37-657 GR230-NH3-4000 0-4000 ppm, 230 VAC A 646

37-652 GR24-NH3-4000 0-4000 ppm, 12-24V AC/DC A 622

Factory settings: Detector type Range (ppm) Alarm levels (ppm) Model - 1000 0 - 1000 150 / 300 / 500 Model - 4000 0 - 4000 150 / 500 / 3000



(NH3) detector for ammonia, for connection to monitoring unit

- Power supply from monitoring unit. - Requires connection to a monitoring unit e.g. SPU, MPU2C, MPU4C, MPU6C or G27C. 1) - Ambient temperature: -40oC...+50oC - Humidity: 0…95% Rh (none condensing) Order code Model Description PG EURO

MP-D Room mounting IP21 Dimensions 80 x 82 x 56mm

38-250 MP-D-(NH3)-1000 0-1000 ppm A 314

38-252 MP-D-(NH3)-4000 0-4000 ppm A 314

MP-DS Splash proof, room mounting IP54 Dimensions 130 x 82 x 56mm

38-450 MP-DS-(NH3)-1000 0-1000 ppm A 391

38-452 MP-DS-(NH3)-4000 0-4000 ppm A 391

MP-DK Detector for duct mounting with 1,5m cable Dimensions 380 x Ø 25 mm

38-850 MP-DK-(NH3)-1000 0-1000 ppm A 391

38-852 MP-DK-(NH3)-4000 0-4000 ppm A 391

MP-DR Detector specially designed for vent lines from pressure relief valves in refrigeration plants. IP54 Dimensions 70 x 25 mm

38-652 MP-DR-NH3-4000 0-4000 ppm A 324

1) Alarm thresholds are set in the monitoring unit and it’s normally done during commissioning. Upon request the monitoring unit can be delivered with pre-set alarm levels for specific gases. The detectors must then be connected to the specified channel. Both monitoring unit and detectors will then be marked for easier installation.



(NH3) detector for ammonia, transmitter (4-20mA)


CS21 4-20mA output Supply 10-30VDC Ambient temperature -30 oC…+50oC IP54

35-130 CS21-NH3-1000 0-1000 ppm C 612

- Remote sensor Option C 130

CI21 Detectors especially developed for harsh conditions for example marine applications with huge temperature and humidity changes. 4-20mA output. Supply 10-30VDC Ambient temperature -30…+50oC IP54

35-100 CI21-200 30-200 ppm C 685

35-110 CI21-1000 30-1000 ppm C 685

35-120 CI21-10000 30-10000 pm C 685

- Remote sensor Option C 130



(NH3) detector for ammonia, (ATEX) Order code Model Description PG EURO

EC28 ATEX classified Output 4..20 mA Supply 15-30VDC Option, LCD display

35-1401 EC28-NH3-100 0-100 ppm C 1209

35-1402 EC28-NH3-100-D 0-100 ppm, With display C 1492

35-1403 EC28-NH3-1000 0-1000 ppm C 1209

35-1404 EC28-NH3-1000-D 0-1000 ppm, With display C 1492

CC28 ATEX classified Output 4..20 mA Supply 15-30VDC Option, LCD display

35-150 CC28-NH3 0-4% C 726

GJ-EX ATEX-classified detector (zone 1 or 2) for explosive and flammable gases including Ammonia. Power supply from monitoring unit. Always connected to a monitoring unit e.g. MPU4C, MPU6C or G27C.

35-321 GJ-EX-NH3-4000 0-4000 ppm 2) C 768

35-325 GJ-EX-NH3-10000 0-10000 ppm NEW! C *)

*) Price on request. Expected delivery from fall 2010. Factory settings: Detector type Range (ppm) Alarm levels (ppm) GJ-EX 0 – 4000 150 / 500 / 3000 2) 2) Alarm thresholds are set in the monitoring unit and it’s normally done during commissioning. Upon request the monitoring unit can be delivered with pre-set alarm levels for specific gases.



(HFC) detector, with relay output


free relay inputs - Ambient temperature: -40oC...+50oC - Humidity: 0…95% Rh (none condensing) Order code Model Description PG EURO


37-225 GD230-HFC 0-4000 ppm, 230 VAC A 412

37-220 GD24-HFC 0-4000 ppm, 12-24 VAC/DC A 386


37-425 GS230-HFC 0-4000 ppm, 230 VAC A 529

37-420 GS24-HFC 0-4000 ppm, 12-24 VAC/DC A 504


37-925 GSR230-HFC 0-4000 ppm, 230 VAC A 595

37-920 GSR24-HFC 0-4000 ppm, 12-24 VAC/DC A 569


37-825 GK230-HFC 0-4000 ppm, 230 VAC A 529

37-820 GK24-HFC 0-4000 ppm, 12-24 VAC/DC A 504

GR Detector specially designed for vent lines from pressure relief valves in refrigeration plants. Standard cable length 1,5m. 160x80x60 mm IP54

37-625 GR230-HFC 0-4000 ppm, 230 VAC A 529

37-620 GR24-HFC 0-4000 ppm, 12-24V AC/DC A 504 Factory settings: Detector type Range (ppm) Alarm levels (ppm) HFC 0 - 4000 100 / 1000 / 2000 2) Refrigerant, type HFC 2) Normal standard calibration is for R134a. The HFC detector is also used for HCFC and CFC.



(HFC) detector, for connection to monitoring unit



38-220 MP-D-HFC 0-4000 ppm A 289


38-420 MP-DS-HFC 0-4000 ppm A 349

MP-DK Detector for duct mounting with 1,5m cable Dimensions 380 x Ø 25mm

38-820 MP-DK-HFC 0-4000 ppm A 349

MP-DR Detector specially designed for vent lines from pressure relief valves in refrigeration plants. IP54 Dimensions 75 x 25mm

38-620 MP-DR-HFC 0-4000 ppm A 295




(HFC) detector, transmitter (4-20mA) Order code Model Description PG EURO

CS21 Output 4-20mA Supply 10-30VDC Ambient temperature: -30 oC…+50oC IP54

35-135 CS21-HFC 0-5000 ppm C 612

- Remote sensor Option. C 130

(HFC) detector in ATEX-classified spaces Order code Model Description PG EURO

GJ-EX ATEX-classified detector zone 1 or 2. Power supply from monitoring unit. Always connected to a monitoring unit e.g. MPU2C, MPU4C, MPU6C or G27C.

35-323 GJ-EX-HFC 0-4000 ppm NEW! C 768

(HFC) detector for room monitoring (hotels, offices etc) - Microprocessor controlled gas detector that detect leaking HFC-gas from air-condition installations, specially designed for

use in offices, hotel rooms, stores etc. - Detects all common HFC-gases and blends - Two alarm levels (high or low) and LED status indication - Built in buzzer (85 dB) - “Fail safe” function - For stand alone use or connected to a central monitoring system. - Long time stable and with 8-10 years expected lifetime Order code Model Description PG EURO

RM SPDT relay output Supply 12-24V AC/DC Ambient temperature: 0 oC…+50oC

32-220 RM-HFC 0 – 5000 ppm (standard calibration for R410A) A *)

*) Price on request. Factory settings: Detector type Range (ppm) Alarm levels (ppm) RM-HFC 0 - 5000 1000 / 4000 Refrigerant, type HFC RM-HFC is pre calibrated for (R410A) but can be delivered for other gases. Contact us for information. The HFC detector is also used for HCFC and CFC.

NEW!



Exhaust gas (VOC) detector for garages, with relay output

- Air quality sensor for garages – Measure exhaust gas and other pollutions that could appear in garages, e.g. carbon

monoxide (CO) and hydrocarbons (HC). - Microprocessor controlled unit with built-in service mode, self-test and ”Fail-safe” function. - Three alarm levels with relays (230V / 5A) - The units can be interfaced with monitoring unit LAN63-PKT, LAN63/64-PKT or to other equipment which accepts a volt



37-265 GD230-AQS 0-200 ppm, 230 VAC A 471

37-260 GD24-AQS 0-200 ppm, 12-24 VAC/DC A 444


37-465 GS230-AQS 0-200 ppm, 230 VAC A 588

37-460 GS24-AQS 0-200 ppm, 12-24 VAC/DC A 562


37-865 GK230-AQS 0-200 ppm, 230 VAC A 588

37-860 GK24-AQS 0-200 ppm, 12-24 VAC/DC A 562 Factory settings: Detector type Range (ppm) Alarm levels (ppm) All models 0 – 200 50 / 50 / 100 1) 1) The detectors are designed to control ventilation (fans) in parking areas. The gas sensor is NOT specific to carbon monoxide (CO) and the sensor will also react to other gases and fumes which may be present in parking areas such as fuel vapour, exhaust emissions and hydrocarbons. (VOC)



Exhaust gas detector for (CO) and (NO2), transmitter (4-20mA / 0-10V) - Detectors for demand-controlled ventilation in parking garages etc. - The detectors measure the concentration of carbon monoxide (CO) and nitrogen oxides (NOx) exhausted from cars and trucks - Electrochemical sensor for high accuracy and stable signal - Output 4-20mA or 0-10 V linear - Power supply 12 – 28 VDC - Ambient temperature -10oC...+40oC - Humidity 0…90% Rh (non condensing) Order code Model Description PG EURO

TR-EC-CO Carbon monoxide transmitter with electrochemical sensor. IP56 Lifetime sensor ~ 6 years Dimensions 80 x 82 x 56mm

39-4260 TR-EC-CO 0-300 ppm (CO) A 351

TR-EC-NO2 Nitrogen dioxide transmitter with electrochemical sensor. IP56 Lifetime sensor ~ 2 years Dimensions 80 x 82 x 56mm

39-4240 TR-EC-NO2 0-10 ppm (NO2) A 536

NEW!



Flammable and explosive gas detector, with relay output




37-295 GD230- Propane 0-40% LEL, 230 VAC A 379

37-290 GD24- Propane 0-40% LEL, 12-24 VAC/DC A 352

37-285 GD230- Methane 0-40% LEL, 230 VAC A 379

37-280 GD24- Methane 0-40% LEL, 12-24 VAC/DC A 352

37-235 GD230-(HC) 0-40% LEL, 230 VAC, Hydrocarbons A 379

37-230 GD24-(HC) 0-40% LEL, 12-24 VAC/DC, Hydrocarbons A 352

37-275 GD230-(H2) 0-40% LEL, 230 VAC, (Hydrogen) A 471

37-270 GD24-(H2) 0-40% LEL, 12-24 VAC/DC, (Hydrogen) A 444


37-495 GS230- Propane 0-40% LEL, 230 VAC A 496

37-490 GS24- Propane 0-40% LEL, 12-24 VAC/DC A 471

37-485 GS230- Methane 0-40% LEL, 230 VAC A 496

37-480 GS24- Methane 0-40% LEL, 12-24 VAC/DC A 471

37-435 GS230-(HC) 0-40% LEL, 230 VAC, Hydrocarbons A 496

37-430 GS24-(HC) 0-40% LEL, 12-24 VAC/DC, Hydrocarbons A 471

37-475 GS230-(H2) 0-40% LEL, 230 VAC, (Hydrogen) A 588

37-470 GS24-(H2) 0-40% LEL, 12-24 VAC/DC, (Hydrogen) A 562


37-995 GSR230-Propane 0-40% LEL, 230 VAC A 594

37-990 GSR24-Propane 0-40% LEL, 12-24 VAC/DC A 568

37-985 GSR230-Methane 0-40% LEL, 230 VAC A 594

37-980 GSR24-Methane 0-40% LEL, 12-24 VAC/DC A 568

37-935 GSR230-(HC) 0-40% LEL, 230 VAC, Hydrocarbons A 595

37-930 GSR24-(HC) 0-40% LEL, 12-24 VAC/DC, Hydrocarbons A 569

Factory settings: Detector type Range Alarm levels All models 0 – 40% LEL 5 / 10 / 20% LEL



Flammable and explosive gas detector, for connection to monitoring unit



38-230 MP-D-(HC) 0-40% LEL A 262

38-280 MP-D-Methane 0-40% LEL A 262

38-290 MP-D-Propane 0-40% LEL A 262


38-430 MP-DS-(HC) 0-40% LEL A 328

38-470 MP-DS-(H2) 0-40% LEL A 375

38-480 MP-DS-Methane 0-40% LEL A 328

38-490 MP-DS-Propane 0-40% LEL A 328




Flammable and explosive gas detector, transmitter (4-20mA) Order code Model Description PG EURO

CS21 Output 4-20mA Supply 10-30VDC Ambient temperature -30 oC ... +50oC IP54

35-137 CS21-Metan-50 0-50% LEL C 612

- Remote sensor Option. C 130


TR5200 Catalytic sensor for flammable gas Output 4..20mA Supply 12-30VDC Ambient temperature -20 oC ... +50oC. IP54

35-450 TR5200-DC 0-100% LEL B 589

Flammable and explosive gas detector, (ATEX) Order code Model Description PG EURO

GJ-EX ATEX-classified detector (zone 1 or 2) for explosive and flammable gases including Ammonia. Power supply from monitoring unit. Always connected to a monitoring unit e.g. SPU, MPU2C, MPU4C, MPU6C or G27C.

35-320 GJ-EX-(HC) 0-40% LEL. C 768

35-322 GJ-EX-(H2) 0-40% LEL. C 768

Factory settings: Detector type Range Alarm levels GJ-EX 0 – 40% LEL 5 / 10 / 20% LEL 1) 1) Alarm thresholds are set in the monitoring unit and it’s normally done during commissioning. Upon request the monitoring unit can be delivered with pre-set alarm levels for specific gases.



(CO2) carbon dioxide detector, with relay output

- Microprocessor controlled unit with built-in service mode, self-test and ”Fail-safe” function. - Three alarm levels with relays (230V / 5A) - Infrared absorption (NDIR) detection with high selectivity and long-term stability. - The units can be interfaced with monitoring unit LAN63-PKT, LAN63/64-PKT or to other equipment which accepts a volt

free relay inputs. - Ambient temperature: See below - Humidity: 0…95% Rh (none condensing) Order code Model Description PG EURO

GS IP56

Range 0 –10 000 ppm 160x130x60 mm

37-412 GS24-CO2-10000 12-24 VAC/DC, temp. 0o…+ 50oC A 638

37-417 GS230-CO2-10000 230 VAC, temp. 0o…+ 50oC A 662

37-412-H GSLT24-CO2-10000 12-24 VAC/DC, low temp -30o…+ 50oC A 735

Factory settings: Detector type Range (ppm) Alarm levels (ppm) Model -10000 0 - 10000 2000 / 2000 / 4000

(CO2) carbon dioxide detector, for connection to monitoring unit

- Infrared absorption (NDIR) detection with high selectivity and long-term stability. - Measurement range 0-10 000 ppm - Power supply from monitoring unit. - Requires connection to a monitoring unit e.g. SPU, MPU2C, MPU4C, MPU6C or G27C. 1) - Ambient temperature: See below - Humidity: 0…95% Rh (none condensing) Order code Model Description PG EURO

MP-D IP21 80 x 82 x 56mm

38-210 MP-D-CO2 Temp: 0oC … + 50o C A 395

MP-DS Splash proof IP56 80 x 82 x 86mm

38-410 MP-DS-CO2 Temp: 0oC … + 50o C A 427

38-410-H MP-DSLT-CO2 Low temperature -30oC … + 50o C A 476


NEW!

NEW!



(CO2) carbon dioxide detector, transmitter (4-20mA / 0-10V)

- Infrared absorption (NDIR) detection with high selectivity and long-term stability. - Output 4-20mA or 0-10 V linear - Power supply 20 – 28 VDC - Ambient temperature: See below - Humidity: 0…95% Rh (none condensing) - Optional, Duct mounting kit available on request Order code Model Description PG EURO

TR-IR Splash proof IP56 Dimensions 80 x 82 x 86mm

39-4312 TR-IR-CO2 0-10 000 ppm, Temperature: 0°C ... +50° C A *)

39-4312-H TRLT-IR-CO2 0-10 000 ppm, For cold rooms, Low temperature: -30°C ... +50°C A *)

*) Price on request. Expected delivery from fall 2010.

NEW!



(CO2) carbon dioxide detector, other

- Infrared absorption (NDIR) detection with high selectivity and long-term stability. - Range 0-2000ppm or 0-5000ppm. - Output: Volt free relay, 0-10V or 4-20mA analogue output. - Fast response time and easy to calibrate Order code Model Description PG EURO

aSense Room mounting with relay and display. Ambient temperature 0…+50oC 120x82x30mm

36-110 aSENSE-R-D 0-2000 ppm, IP21, 24VAC/DC B 587

36-120 aSENSE-5000-R-D 0-5000 ppm, IP21, 24VAC/DC B 610

aSENSE IP54

Splash proof detector with relay and display Ambient temperature 0 …+50oC 150x85x48mm

36-112 aSENSE-R-D-IP54 0-2000 ppm, IP54, 24VAC/DC B 688

36-122 aSENSE-5000-R-D-IP54 0-5000 ppm, IP54, 24VAC/DC B 711

UG-aSense Duct mounting with relay and display. Ambient temperature 0 … +50oC 110x287x159mm Tube length 600mm

36-115 UG-aSENSE-R-D 0-2000 ppm, IP54, 24VAC/DC B 655

36-125 UG-aSENSE-5000-R-D 0-5000 ppm, IP54, 24VAC/DC B 679

LT-aSense For installation in cold rooms, with relay output Built in heater, NOTE! power consumption up to 2A Ambient temperature -30oC...+50oC 180x95x65mm

36-130 LT-aSENSE-5000-R 0-5000 ppm, IP54, 24VAC/DC B 1069 Factory settings: Detector type Range (ppm) Alarm levels (ppm) aSENSE (all models) 2) 0-2000 ppm 1000 ppm aSENSE-5000 (all models) 2) 0-5000 ppm 2000 ppm 2) Detectors type aSENSE are available in different models and measuring ranges.



(O2) detector for oxygen Order code Model Description PG EURO

GMA36 Pro

Stand alone or connected to a monitoring unit. Display Outputs, three relays Electrochemical sensor Measuring range 0 - 30% (O2)

35-190 GMA36-(O2) 0 - 30% (O2), supply 85...264V C 1373

(O2) detector for oxygen, (ATEX) Order code Model Description PG EURO

EC28

Stand alone or connected to a monitoring unit. Electrochemical sensor Output 4-20mA Supply 15…30VDC Option, LCD Display

35-1421 EC 28 EX-(O2) 0 - 25% (O2), ATEX C 1029

35-1422 EC 28 EX-(O2)-D 0 - 25% (O2), ATEX, With display C 1316



Portable detectors

Carbon dioxide (CO2) Order code Model Description PG EURO

aSENSE-alarm (CO2)

Non-Dispersive Infrared (NDIR) LED’s and audible signal for alarm. Internal automatic self-diagnostic function and easy to calibrate. Charger and leather bag included

50-001 aSENSE-alarm 0 - 3% CO2 C 696

Ammonia, (O2) and toxic gas Order code Model Description PG EURO

MICRO IV

Detector for toxic gases, including Ammonia, and oxygen. Electrochemical sensor Audible and visual alarm. Display ATEX classified. Pump as option

50-120 MicroIV - NH3 - 200 0 - 200 ppm C 705

50-1201 MicroIV - NH3 - 500 0 - 500 ppm C 705

50-121 MicroIV - O2 0 - 25% C 423


Microtector II

Detector for 1-6 different gases. Display. ATEX classified.

50-130 G450 4 gases C *)

50-131 G460 6 gases C *)

*) Price on request



Auxiliary equipment

Battery back-up Order code Model Description PG EURO

UPS

Output: 12V DC Maximal load: 1,5A Battery: 12V / 2Ah Housing: Plastic, IP67 Dimensions: 230x140x95mm

40-210 UPS1500 A 489

UPS

Output: 6, 12 or 24V DC Maximal load: 4,0A Batteries: 12V / 7Ah (Battery to be ordered separately) Housing: Metal, IP21 Dimensions: 370x315 x95mm

40-220 UPS4000 A 504

80-320 Battery 12V/7,2Ah weight 2,4 kg Net 34

Transformer Order code Model Description PG EURO

PSS Power supply: 230V AC Secondary: 12V AC or 24V AC Housing: IP30

40-510 PSS32/12V 230/12V 32VA, IP30 Net 56

40-520 PSS60/24V 230/24V 60VA, IP30 Net 61

BE Flashing lights Order code Model Description PG EURO

BE

IP43 (IP65 with SOCK-H-R, option) Colours: Red, blue or amber (for other colours please contact us). If 230V supply always IP65

40-4021 BE-A-24VDC Amber, 9 - 60VDC B 66

40-4022 BE-R-24VDC Red, 9 - 60VDC B 66

40-4023 BE-BL-24VDC Blue 9 – 60VDC B 66

FL IP43 (IP65 with SOCK-H-R, option) If 230V supply always IP65

40-440 FL-RL-R Combined flashing light and siren, Red, 18 - 28VDC B 153

40-415 SOCK-H-R Socket IP65 B 11

40-420 SOCK-H-R-230 Socket 230V AC, IP65 B 50



Auxiliary equipment

Siren Order code Model Description PG EURO

1992-LP IP54 (IP65 with optional socket) Programmable with DIP-switch for different sound.

40-410 1992-R-LP 9-28 VDC, Red B 60

40-415 SOCK-H-R Socket IP65 B 11

40-420 SOCK-H-R-230 Socket 230V AC, IP65 B 50

GR-cable Order code Model Description PG EURO

GR-cable Extra long oil-resistant soft cable to GR-detectors, with pre mounted plug-in terminal for PCB and pre-mounted socket for gas sensor.

33-601 GR- cable 2,5m A 50

33-602 GR- cable 5,0m A 63

33-603 GR- cable 8,0m A 81

Wall mounted enclosures Order code Model Description PG EURO

Enclosure accepts one G27C, a PSS 32/12 transformer plus two optional relays.

40-600 N10-55L With transparent lid, IP54 A 49



Auxiliary equipment

Service tools - SA100: Service tool for control and calibration of detectors type GD/GS/GR2.0 and for monitoring unit G27C. - SA200: Service tool for control and calibration of detectors type GD/GS/GR/GK/GSR230, GD/GS/GR/GK/GSR24 and for detectors connected to monitoring unit SPU, MPU2C/..4C/..6C. Order code Model Description PG EURO

SA100 / SA200

60-110 SA100 Net 78

60-120 SA200 Net 78

Options, Service and Commissioning


90-100 Service engineer, per hour Net *)

90-101 Design and consultancy, per hour Net *) 90-110 Travelling costs, contact us for information Net *)

Changing of standard pre-set alarm levels, (in combination with new orders)

60-300 Pre-set alarm levels/channel (Gx24/Gx230-series, SPU, MPU) Net 25

*) Price on request

Terms and conditions of sale - All prices in Euro, Ex-works, packing included - Delivery terms, NL01, (Incoterms 2000) - Proforma payment. Credit terms 30 days net by wire transfer. - We reserve the right to change prices without notification. - Technical specifications subject to alteration.

SAMON ABMODEMGATAN 2

S-235 39 VELLINGESWEDEN

TEL + 46 – (0)40 – 15 58 59FAX + 46 – (0)40 – 15 60 31

WWW.SAMON.SE

Distributor:

catalogue 10 euro nh3

Documents

pressure relief

led status

manualauto

microprocessor

failsafe relay

normal standard

product catalogue

carbon dioxide