catalogue of products 2011 vinci technologies · 2011. 3. 11. · vinci technologies parc de...

VIN

CI

TE

CH

NO

LO

GIE

S

PE

TR

OP

HY

SIC

S

CATALOGUE OF PRODUCTS

2011

PETROPHYSICS

Core preparation

Routine core analysis

Special core analysis

Components

VINCI TECHNOLOGIES

Parc de l'Ile, 27B rue du Port, 92022 NANTERRE

Phone: 331 41 37 92 20 Fax: 331 41 37 04 76

e-mail: [email protected]

http://www.vinci-technologies.com 3/100

PE

TR

OP

HY

SIC

S

LIST OF INSTRUMENTS

CORE PREPARATION ______________________________________ 6

PLUGGING MACHINE __________________________________________________________ 7

RADIAL CORE SLABBING SAW ___________________________________________________ 8

AUTOMATIC SLABBING SAW ____________________________________________________ 9

CORE CUTTING SAW __________________________________________________________ 10

TRIMMING SAW _____________________________________________________________ 11

ENDFACE GRINDER __________________________________________________________ 12

TRIMMING / ENDFACE GRINDER ________________________________________________ 13

CENTRIFUGAL EXTRACTOR ____________________________________________________ 14

CO2 SOLVENT CORE CLEANER (CSC 70) __________________________________________ 15

SOXHLET EXTRACTOR ________________________________________________________ 16

FLOW THROUGH CORE CLEANER ________________________________________________ 17

RECOVERY STILL FOR SOLVENT _________________________________________________ 18

HUMIDITY DRYING OVEN ______________________________________________________ 19

VACUUM DRYING OVEN _______________________________________________________ 20

AIR FORCED DRYING OVEN ____________________________________________________ 21

HEATED VACUUM DESSICATOR _________________________________________________ 22

MANUAL SATURATOR ________________________________________________________ 23

AUTOMATED SATURATOR _____________________________________________________ 24

CORE DESAGREGATOR ________________________________________________________ 25

STEREOMICROSCOPE _________________________________________________________ 26

ULTRA VIOLET BOX __________________________________________________________ 27

CORE PRESERVATION KIT _____________________________________________________ 28

ROUTINE CORE ANALYSIS ________________________________ 29

HIGH PRECISION DIGITAL BALANCES _____________________________________________ 30

DEAN STARK EXTRACTOR _____________________________________________________ 31

RETORT OVEN ______________________________________________________________ 32

GAMMA RAY LOGGER (NGR 200) _______________________________________________ 33

GEOMETRIC BULK VOLUME METER (GBV) _______________________________________ 34

IMMERSED BULK VOLUME METER (IBV) _________________________________________ 35

MERCURY POROMETER _______________________________________________________ 36

HELIUM POROSIMETER (HEP) __________________________________________________ 37

HELIUM POROSIMETER FOR EDUCATIONAL PURPOSES (HEP-E) ________________________ 38

STEADY STATE GAS PERMEAMETER (GASPERM) ____________________________________ 39

STEADY STATE GAS PERMEAMETER FOR EDUCATIONAL PURPOSES (GPE30) ______________ 40

WHOLE CORE STEADY STATE GAS PERMEAMETER (WHOLEPERM) ______________________ 41

STEADY STATE GAS PERMEAMETER AND POROSIMETER (POROPERM) ___________________ 42

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

STEADY STATE GAS PERMEAMETER AND POROSIMETER FOR EDUCATIONAL PURPOSE

(POROPERM - E) _____________________________________________________________ 43

CALIBRATED PERMEABILITY CHECK PLUGS _______________________________________ 44

UNSTEADY STATE GAS PERMEAMETER AND POROSIMETER AT MODERATE CONFINING

PRESSURE (COREVAL 30) ______________________________________________________ 45

UNSTEADY STATE GAS PERMEAMETER AND POROSIMETER AT OVERBURDEN PRESSURE

(COREVAL 700) _____________________________________________________________ 46

AUTOMATED SAMPLE LOADING UNSTEADY STATE PERMEAMETER AND POROSIMETER AT

OVERBURDEN PRESSURE (KEYPHI)_______________________________________________ 47

LIQUID PERMEAMETER (LIQPERM) ______________________________________________ 48

BENCH TOP PERMEABILITY SYSTEM (BPS 350) ____________________________________ 49

BENCH TOP UNSTEADY STATE RELATIVE PERMEAMETER (BRP 350) ___________________ 50

BENCH TOP UNSTEADY & STEADY STATE LIQUID – LIQUID RELATIVE PERMEAMETER (SRP

350) ______________________________________________________________________ 51

ELECTRICAL PROPERTIES SYSTEM @ AMBIENT CONDITIONS (EPS-A) __________________ 52

ELECTRICAL PROPERTIES SYSTEM @ OVERBURDEN PRESSURE (EPS 700) ________________ 53

EDUCATIONAL CAPILLARY PRESSURE CELL _______________________________________ 54

MULTI SAMPLE CAPILLARY PRESSURE CELL _______________________________________ 55

CAPILLARY PRESSURE REFRIGERATED CENTRIFUGE (RC4500) ________________________ 56

CAPILLARY PRESSURE MERCURY SYSTEM (CPM 140) _______________________________ 57

DIGITAL CORE PHOTOGRAPHY SYSTEM (DCP) _____________________________________ 58

SPECIAL CORE ANALYSIS _________________________________ 59

CORE FLOOD SYSTEM FOR EOR STUDIES (CFS 700) _________________________________ 60

UNSTEADY STATE RELATIVE PERMEAMETER (AUTOFLOOD 700) _____________________ 61

STEADY STATE AND UNSTEADY STATE RELATIVE PERMEAMETER SYSTEM (RPS 700) _______ 62

XRAY SCANNER FOR IN-SITU SATURATION MONITORING _____________________________ 63

FORMATION DAMAGE AND WELL TREATMENT EVALUATION SYSTEM (FDS 350) __________ 64

CAPILLARY PRESSURE AND RESISTIVITY INDEX SYSTEM (CAPRI) _____________________ 65

ROCK COMPRESSIBILITY SYSTEM (RCS 700) ______________________________________ 66

ATMOSPHERIC ACOUSTIC VELOCITY SYSTEM (AVS A) ______________________________ 67

OVERBURDEN ACOUSTIC VELOCITY SYSTEM (AVS 700) _____________________________ 68

AUTOMATED HP-HT ACOUSTIC VELOCITY SYSTEM (AVS 700-HT) ___________________ 69

AGING CELL APPARATUS (ACA 700) ____________________________________________ 70

COREHOLDERS __________________________________________ 71

HASSLER COREHOLDER (HAS SERIES) ____________________________________________ 72

HYDROSTATIC COREHOLDER (HYC SERIES) ________________________________________ 73

TRIAXIAL COREHOLDER (TRC SERIES) ____________________________________________ 74

LEAKOFF COREHOLDER (LEC SERIES) ____________________________________________ 75

QUICK RELEASE COREHOLDER (QRC SERIES) _______________________________________ 76

TRANSPARENT COMPOSITE COREHOLDER (TCC SERIES) ______________________________ 77

ACOUSTIC VELOCITY COREHOLDER (AVC SERIES) __________________________________ 78

ELECTRICAL RESISTIVITY AND CAPILLARY PRESSURE COREHOLDER (ECP SERIES) _________ 79

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

HEATING SYSTEM (HES SERIES) _________________________________________________ 80

STANDS (STA SERIES) _________________________________________________________ 81

CORE ANALYSIS COMPONENTS ____________________________ 82

LEVEL TRACKER SEPARATOR (LTS SERIES) ________________________________________ 83

DUAL LEVEL TRACKER (DLT SERIES) ____________________________________________ 84

AMBIENT CONDITIONS TWO PHASE VIDEO SEPARATOR (VSE -A) ________________________ 85

HP-HT TWO PHASE VIDEO SEPARATOR (VSE 700) ____________________________________ 86

WET GAS METER (WG SERIES) __________________________________________________ 87

CAPILLARY SIGHT GLASS TUBE _________________________________________________ 88

BACK PRESSURE REGULATOR (BPR) _____________________________________________ 89

ELECTRICAL ISOLATOR (EI 700) ________________________________________________ 90

AUTOMATED CONFINING PRESSURE CONTROLLER (ACP 700) _______________________ 91

FLOATING PISTON ACCUMULATOR (FPA SERIES) ___________________________________ 92

MIXER CYLINDER (MC SERIES) _________________________________________________ 93

FLUID TRANSFER VESSELS (FTV SERIES) __________________________________________ 94

HYDRAULIC INTENSIFIER (HI SERIES) ____________________________________________ 95

PRESSURE GENERATOR SYSTEM (PGS) ___________________________________________ 96

DIGITAL PRESSURE GAUGE (DPG SERIES) __________________________________________ 97

DEADWEIGHT GAUGE_________________________________________________________ 98

UNINTERRUPTABLE POWER SUPPLY (UPS 16) ______________________________________ 99

OTHER COMPONENTS ________________________________________________________ 100

The specifications and photos contained in this catalogue can be subject to change without

notification.

Copyright© Vinci Technologies. All rights reserved.

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CORE PREPARATION

Core cutting

Core cleaning

Core drying

Core saturation

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

PLUGGING MACHINE

The heavy built diamond tooled drill press is especially designed to drill in various size core

samples. The standard machine comes with a floor standing drill press, a rotary union, a coolant

feeding system, a coolant recovery pan with splash guard and a core clamping vise. The union

permits to connect the coring bit to the drill press and feed coolant to the coring bit. The vise

assembly can be mounted on the pan table and allows for the positioning of the core. Various

sizes of coring bits as well as the recirculating coolant system are available.

FEATURES

Coring bit internal diameter: 1", 1.5", 2"

Maximum coring depth: 5 inches (12.5 cm)

Drip pan dimension: L x W x H: 600 x 300 x 250 mm

Compatible coolant: Water, Oil

Drill speed: 360, 520, 800, 1150, 1840, 2650, 4070, 5750 RPM

Motor power: 1100 watts, 1500 RPM

Electrical: 220 VAC 1 phase, 60 Hz

Weight: 150 kg

Volume: 500 x 500 x 1800 mm

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

RADIAL CORE SLABBING SAW

Versatile diamond impregnated radial blade utilised to slab core samples in two halves or to

trim full diameter rock samples. The standard machine comes with a worktable, blade guard,

motor to power the saw, core clamp assembly for holding core, sample trolley on ball bearing

guide, coolant feeding system , coolant recovery pan and diamond impregnated saw blade. The

recirculating coolant system is also available.

FEATURES

Saw blade diameter 400 mm (16‟‟) (other upon request, max 500 mm)

Maximum cutting depth 125 mm (5”)

Max core length 300 mm, 1000 mm in option

Compatible coolants Water and oil

Power supply 220 VAC, 50 Hz, 4,000 W

Weight 320 kg

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

AUTOMATIC SLABBING SAW

Versatile diamond impregnated radial blade utilized to slab core samples in two halves or to

trim full diameter rock samples. The automated machine is fitted with a variable rate feed

mechanism that enables the cutting of long section of very dense core in one pass without

fracturing, grooving or chipping and producing a high-finished surface. The core sample

remains fixed, while the carriage holding the diamond disc and motor unit moves along the core

sample at an adjustable and regulated speed. The moving of the saw blade along the core sample

starts when the cutting depth is reached. The saw arm oscillates around an axis so that a

constant cut pressure is maintained whatever the hardness of the sample material encountered.

This pressure is easily adjusted while the machine is in operation.

FEATURES

Saw blade diameter 500 mm (20‟‟)


Maximum core length 1 meter


Power supply 380 VAC 3 Phases, 50 or 60 Hz, 8,000 W

Weight 1200 kg

Volume 4000x1050x2030 mm

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CORE CUTTING SAW

Versatile bench top diamond impregnated radial blade utilized to cut plug sized core samples in

two halves or to trim rock samples. The standard machine comes with a blade guard, a motor to

power the saw, a sample trolley on ball bearing guide, a shut off button, a coolant feeding

system, a coolant recovery pan and a diamond impregnated saw blade.

FEATURES

Saw blade diameter 350 mm (14”)


Max core length 300 mm


Power supply 220 or 380 VAC, 50 Hz, 3 horses

Weight 82 kg


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

TRIMMING SAW

Bench top tool designed to cut preset core sample lengths. The preset sample lengths can be

adjusted at any time by rearranging machined spacers to the desired length between the blades.

The quality of the saw blade allows for extreme precision of the end face after trimming of

0.002 inch (5/100 mm). All wetted components are constructed from stainless steel and

anodized aluminium for long lasting corrosion free operation. All bearings are sealed to insure

long lasting free movement. The containment pans and splash guards are also constructed of

heavy gauge stainless steel, anodized aluminium and corrosion free plastic. Recirculating

coolant system is also available.

FEATURES

Saw blade diameter 200 mm (8‟‟)

Saw blade thickness 2 mm

Core diameter up to 2‟‟

Core length 2”, 3” other upon request

Lubricants water (usually), oil

Power supply 220 VAC 1 phase 50 or 60 Hz

Motor power 550 W, 3,000 RPM

Weight 80 kg

Dimension 700x800x600 mm

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

ENDFACE GRINDER

Tool designed to provide flat, parallel end-faces when sample geometry is critical for advanced

rock property test. The tool comes with a core clamping device, housing and cover parts, a

coolant feeding system, a coolant recovery pan and a diamond tool end-face grinding wheel. A

core clamping device for whole diameter core sample, a recirculating coolant system and

hoover for dry grinding operations are also available.

FEATURES

Core diameter up to 2"

Grinding wheel precision +/- 0.001 inch (2.5 / 100 mm)

Wheel diameter 150 mm

Power supply 220 VAC 1 ph50 or 60 Hz

Motor power 0,55 kW, 3,000 RPM Weight 70 kg


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

TRIMMING / ENDFACE GRINDER

Bench top tool which combines a trimming saw at one side and an endface grinder on the other

side. It is designed to cut preset core sample lengths and grind the sample with extreme

precision of the end face after trimming of 0.002 inch (5/100 mm).

FEATURES

Saw blades diameter 200 mm (8‟‟)

Saw blades thickness 2 mm

Grinding precision +/- 0.001 inch (2.5 / 100 mm)

Grinding wheel diameter 150 mm

Core diameter up to 2‟‟

Core length 2”, 3” other upon request

Lubricants Water (usually), Oil

Power supply 220 VAC 1 ph 50 / 60 Hz

Motor power 550 W, 3,000 RPM

Weight 100 kg


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CENTRIFUGAL EXTRACTOR

The centrifugal extractor is designed to spray warm, clean solvent from a still against the core

samples. The centrifugal force causes solvent to flow through samples displacing and extracting

the oil (and water). The speed of rotation can be selected depending on the permeability and

degree of consolidation of the core. Most common solvents can be used. A solvent recovery still

is also provided to recycle clean and warm solvent into the centrifugal extractor in closed loop.

FEATURES

Core diameter up to 2"

Core length up to 3‟‟

Quantity of sample between 6 to 18 depending on the core length

Wetted materials Stainless steel, teflon

Centrifuge speed up to 3000 rpm

Electrical 220V, 50Hz, 1500W

BENEFITS

Centrifugal Extractor :

Rapid and efficient extraction of oil, water and salt from consolidated core samples

Speed controller

Rotor geometry to accomodate the core samples

Solvent inlet and outlet

Vibration free chassis

Solvent recovery still :

Heated solvent flask

Water refrigerant for solvent condensation

Temperature controller

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CO2 SOLVENT CORE CLEANER (CSC 70)

The core Cleaner is a device for cleaning crude oil, drilling mud liquids, and water from a single

piece of whole core or from a batch of core plug samples. The principle consists of filling the

gas filled space in the core with solvent (e.g. toluene) by surrounding the core with a suitable

solvent containing dissolved CO2 gas and applying sufficient hydraulic pressure. The solvent

mixes with oil in the core and subsequent depressurizing to atmospheric pressure removes

residual oil from the core. A number of repeated cycles are required to clean the core of

hydrocarbons.

The apparatus fits into a standard size floor hood. The cleaning chamber is a pressure vessel

heated electrically with a two-kilowatt, 220-volt heater enclosed in an explosion proof housing.

The solvent is pumped from an onboard supply tank to the cleaning vessel with a high pressure

pump. A cyclone separator with a stainless steel-packed, water-cooled after-cooler is provided

to separate the CO2 and the used hot solvent when the vessel is drained. The used toluene drains

into an explosion proof electric still where it is recovered and delivered back to the clean

solvent supply. The still operation is automatic. The process controls are housed in a non-

explosion proof box intended to be mounted outside of the hood.

FEATURES

Vessel diameter: Model 1:4.6” (118 mm) - Model 2: 5.2” (134 mm)

Vessel length Model 1:10.7” (274 mm) - Model 2: 27” (660 mm)

CO2 pressure 200 psi

Solvent pressure 1,000 psi

Wetted materials 316 Stainless steel

Net weight 200 kg

Requirements:

Air 100 psi

Electrical 220V, 50Hz, 2,000 Watts

Cooling water 8 l/m @ 14 kPa (2 gpm @ 20 psi)

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

SOXHLET EXTRACTOR

The soxhlet distillation extraction method is used to dissolve and extract oil and brine from rock

core sample by using solvents. The cleanliness of the sample is determined from the color of the

solvent that siphons periodically from the extractor which must be clear. The samples are

placed in the extractor and cleaned by refluxing solvent. The solvent is heated and vaporized in

boiling flasks and cooled at the top by condenser. The cooled solvent liquid falls into the sample

chamber. The cleaned solvent fills the chamber and soaks the core sample. When the chamber is

full, the dirty solvent which was used to clean the core siphons back into the boiling flask and is

redistilled again The apparatus consists of a distillation/extraction glassware unit and a heating

mantle with thermostatic controller. The glassware is composed of boiling flask, soxhlet

extractor and condenser. A flexible plastic tubing is also used to connect the condenser to the

water cooling unit. All these devices are mounted on a mounting rack.

FEATURES

SOXHLET FOR PLUG SIZED CORE SAMPLES

Configuration Single unit model/ Multiple units model (up to 6 extractors)

Core sample diameter up to 1,5”

Core sample length up to 4”

Extractor capacity 250 ml

Boiling flask 500 ml

Heating temperature up to 450°C

Water cooling system 0.5 to 3 liters per minute, 18°C

Power supply 220 VAC 50 Hz

SOXHLET FOR FULL SIZED CORE SAMPLES

Configuration Single unit model / Multiple units model (up to 6 extractors)

Core sample diameter up to 4”


Extractor capacity 3 liters

Boiling flask 6 liters




VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

FLOW THROUGH CORE CLEANER

The apparatus is a rapid and efficient core cleaning system based on controlled sequential

solvent displacement under moderate pressure. Extraction of hydrocarbons and salts from

reservoir rocks is achieved by injecting one or more solvents into the core sample under

pressure and moderate temperature. The pressure used depends on the sample permeability. The

core is considered clean when the effluent is clean.

FEATURES

Maximum confining pressure 1,000 psi

Core diameter 1.5” (other upon request)

Core length Up to 3” (other upon request)

Fluid flow rate 5 cc/min (recommended)

Wetted parts Stainless steel

Electrical 220 VAC, 50 Hz

Weight 40 Kg

BENEFITS

Possibility to pump different solvents

Constant injection flow for solvent

Easy core loading and unloading operation

Cleaning at pressure for high permeability sample

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

RECOVERY STILL FOR SOLVENT

The recovery still is designed to reclaim clean solvent from dirty solvent containing a mixture of

crude oil and solvent. The recovery process is based on fractional distillation by boiling point

temperature difference between the crude oil and the solvent. The apparatus is explosion proof

and should be installed away from any area of hazardous atmosphere. It consists mainly of (a)

an insulated boiler tank equipped with heaters located at the bottom and (b) a condenser using

house water. The recovered solvent is evacuated into a container whereas the dirty toluene is

transferred manually into the tank. The plastic bag located in the tank in which the dirty solvent

is poured permits to facilitate the evacuation of sludge deposit after the recovery process.

FEATURES

Recovery 95 %

Recovery time 3 to 5 hours for 20 litres

Max temperature 200°C

Tank capacity 20 litres, other upon request

Protection IP 66

Material stainless steel

House water consumption 50 litres per hour

Power supply 220 VAC 50 Hz , 2,500 W

Dimensions 850x1000x1000 mm

Weight 165 Kg

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

HUMIDITY DRYING OVEN

The humidity drying oven is used to dry core samples under constant relative humidity

condition; in particular it is very important when the core contains hydratable clays or gypsum.

This oven is composed of a robust air bath, an electronic temperature regulator, a water vapor

injection system, a capacitance probe to control humidity level and a timer.

FEATURES

Capacity 240 liters

Humidity range 10% to 90%

Temperature +10°C + 90°C

Humidity stability +/- 1%

Temperature stability +/- 0.1 °C

Internal dimensions 800 x 500 x 600 mm

Power supply 220V / 50Hz , 2500 W

Weight 184 kg

Water consumption 1 – 10 bar (200 – 500 S/cm)

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

VACUUM DRYING OVEN

The vacuum drying oven enables fast drying of core under vacuum. This oven is composed of a

robust vacuum air bath, an electronic temperature regulator and digital vacuum control through

solenoid valves. Two sizes can be selected.

FEATURES

MODEL 1: 53 LITRES VACUUM OVEN

Capacity 53 liters

Temperature 20 to 200°C

Vacuum 10 mb

Internal dimensions 400 x 400 x 330 mm (WxHxD)

Power supply 220V, 50Hz, 1200 W

Weight 80 kg

MODEL 2: 115 LITRES VACUUM OVEN

Capacity 115 liters

Temperature 20 to 200°C

Vacuum 10 mb

Internal dimensions 506 x 506 x 450 mm (WxHxD)

Power supply 220V, 50Hz , 1900 W

Weight 150 kg

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

AIR FORCED DRYING OVEN

The air forced drying oven enables efficient drying of core samples after cleaning with solvents

before permeability or porosity measurements. This oven is composed of a robust air forced

convection air bath, a variable speed turbine, an electronic temperature regulator and a timer .

Two sizes are available.

FEATURES

53 LITERS MODEL

Capacity ……………………. 53 liters

Temperature ………………… 220°C

Internal dimensions…………..400 x 330 x 400 mm

Power supply ……………….220V , 50Hz , 2,000 W

Weight ……………………….42 kg

108 LITERS MODEL

Capacity ……………………. 108 liters

Temperature ………………... 220°C

Internal dimensions…………. 556 x 400 x 480mm

Power supply………………… 220V , 50Hz , 2,000 W

Weight ………………………63 kg

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

HEATED VACUUM DESSICATOR

The vacuum heated dessicator is designed especially to dry a bunch of core samples under

vacuum. This operation is required to remove humidity of core samples before gas permeability

or porosity measurements. The system includes an heated dessicator and a vacuum pump. The

dessicator includes a machined stainless steel heating plate with a glass bell, designed to

withstand the pressure difference between in and outside. The sealing is secured by a viton O-

ring between the heating plate and the bell. The samples are dried by direct contact with the

heating plate. The small volume and the compact design guarantee a short heating time. It is

easy and safe to operate, requires hardly any maintenance, and visibility is perfect.

FEATURES

Temperature………………… up to 80°C

Vacuum... …...……………… 10 -3

mbar

Max pumping speed………… 2.5 m3/h

Quantity of sample…………… around 30

Material ………………………..stainless steel 316L

Electrical …………………….. 220V, 50Hz,

BENEFITS

Rapid and efficient drying

Total visibility on the product to be dried

Compact

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

MANUAL SATURATOR

The manual saturator permits to perform a sequence of vacuum and saturation cycles on plug

size samples. The standard apparatus includes a plug sized core cell, a vacuum pump, an hand

operated pressure pump (2,000 psi output), a saturant vacuum tank and necessary hand operated

valves and plumbing. A larger capacity cell to accommodate full size core samples is also

available.

FEATURES

Max saturating pressure 2,000 psi

Cell diameter 58 mm

Cell height 300 mm

Wetted materials 316 Stainless steel (other on request) Saturant water, brine, oil or other liquids

BENEFITS

Rapid and efficient saturation

Can accomodate plug size sample and full sized core sample in option

Manual operations

Loading carrier for easy loading

Dead volume sets to minimize volume of saturant

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

AUTOMATED SATURATOR

The automated saturator permits to perform a sequence of vacuum, filling and saturation cycles

on plug size samples in an automated mode to free the operator for other tasks. The bench top

apparatus comes with a plug sized core cell, a vacuum pump, a high pressure liquid pump

(2,000 psi output), a saturant vacuum tank and necessary automated valves and plumbing. A

larger capacity cell to accommodate full size core samples is also available. The apparatus is

controlled by a touch screen panel PC which allows the operator to open or close the valves,

start and stop the high pressure pump, the vacuum pump and to run automatic saturation cycles.

FEATURES

Max saturating pressure 2,000 psi

Cell diameter 58 mm

Cell height 300 mm

Wetted materials 316 Stainless steel (other on request) Saturant water, brine, oil or other liquids

Power supply 220 VAC, 50 Hz

BENEFITS

Rapid and efficient saturation

Can accomodate plug sized sample and full sized core sample

Fully automated operations

Loading carrier for easy loading

Dead volume sets to minimize volume of saturant

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CORE DESAGREGATOR

Designed to pulverize core samples into a small granular texture to be loaded in the sample

chamber. The sample is crushed under high pressure between two crushing plates in an enclosed

chamber.

FEATURES

Crushing type by pressure

Feed size 65 x 65 mm

Initial core size 60 mm

Final particle size 1 to 15 mm

Capacity up to 200 kg/h

Power supply 220 or 380 VAC , 50 Hz , 1,100 W

Dimensions 410 x 830 x 720 mm

Net weight 177 Kg

BENEFITS

Adaptable crushing geometry

10 stage gap setting adjustment

Crushing plates easily accessed and replaced

Not accessible, moving part fully interlocked casing

Very fast, uniform comminution

Almost loss free grinding

Closed grinding chamber with extraction part for dust free operations

Easy cleaning, minimum contamination between samples

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

STEREOMICROSCOPE

The Stereomicroscope Stemi 2000 meets your demands in two respects.

On the one hand it offers the low-price advantage common with Greenough-type instruments,

on the other hand it features a performance that will surely surprise you. The extremely wide

7.7:1 zoom range (pancratic system 0.65x...5.0x) zooms them in as hardly any other

stereomicroscope of this class can do. It includes a cold light source.

FEATURES

Model ZEISS STEMI 2000

Magnification x6.5 …x50

Viewing field Max 23mm

Working distance 90 mm

Power supply 220 VAC 50Hz

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

ULTRA VIOLET BOX

The ultra violet box is composed of a ultra violet light tube and a fluorescent white light to

enable observation of core and cutting samples under both UV light and white light. An access

permits to introduce the sample inside the box without introducing exterior light.

FEATURES:

Light UV and white fluorescent light

Power supply 220 VAC 50Hz

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CORE PRESERVATION KIT

The core preservation kit provides the components necessary for the core preservation

technique. It consists of wrapping the core sample in several layers of high quality plastic film

to prevent puncturing and then wrapped it again with several layers of aluminum foil, with the

free ends crimped together. A wire is tied around the core to make a handle. The foil-wrapped

core sample is then dipped in a molten wax coating material for mechanical stabilization. The

prepared core is then introduced in a heat sealed plastic bag for transportation.

FEATURES:

Roll of high quality plastic film

Roll of aluminium film

Roll of wire

Melting pot for wax coating

Wax coating

Cooling rack

Heat sealer

Bag film kit

Bags

Glue

Shovel

Pair of gloves

Labelling facilities

Grabs and scissors

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

ROUTINE CORE ANALYSIS

Capillary pressure

Coreval 30

Electrical Properties System

BRP 350

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

HIGH PRECISION DIGITAL BALANCES

Digital balances especially selected for core applications where measurement accuracy is

required.

FEATURES

TYPICAL BALANCE FOR PLUG SIZED CORE SAMPLES

Weighing range 0-620 g, other upon request

Accuracy 0.001 g


TYPICAL BALANCE FOR FULL SIZED CORE SAMPLES

Weighing range 6,200 g, other upon request

Accuracy 0.01 g


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

DEAN STARK EXTRACTOR

The dean stark extractor is used to determine fluid saturation of core samples. The sample is

first weighed and then introduced into the dean stark extractor. The water fraction is vaporized

by boiling solvent, condensed and then collected in a calibrated receiver. Vaporized solvent also

condenses, soaks the sample, and extracts the oil. The sample is then oven dried and weighed.

The oil content is determined by gravimetric difference while the water content is

volumetrically measured by the receiving tube. The apparatus consists of a

distillation/extraction glassware unit and a heating mantle with thermostatic controller. The

glassware is composed of boiling flask with extractor, a sample support screen, volumetrically

graduated water receiving tube, condenser and desiccant drying tube. A flexible plastic tubing is

also used to connect the condenser to the water cooling unit. All these devices are mounted on a

mounting rack

FEATURES

DEAN STARK FOR PLUG CORE SAMPLE


Core sample diameter up to 1.5”


Extractor capacity 250 ml

Boiling flask 500 ml

Receiving tube 5 & 10 ml, 0.1 ml graduation



Power supply 220 VAC 50 HZ

DEAN STARK FOR FULL SIZE CORE SAMPLE


Core sample diameter up to 4”


Extractor capacity 3 liters

Boiling flask 6 liters

Receiving tube 40 ml, 0.2 ml graduation with drain valve




VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

RETORT OVEN

The retort oven is designed to determine oil and water fluid saturation by a high temperature

retorting process in which the oil and water contained in a fresh sample of crushed core material

are vaporized, condensed and collected in calibrated glassware. The samples are progressively

heated to remove water and then heat up to 650°C (1,200°F) to remove oil from the sample. The

gas saturation is determined on an adjacent, litho logically similar sample by placing the core

sample in a mercury porosimeter and measuring the amount of mercury injected with the water

and/or oil in place. The system comprises a retort cabinet containing two chambers of five

sample bombs capable of holding crushed core material. Each bomb is equipped with a sealed

threaded cap and is connected to a long, stainless steel condensing tube. The tube passes

through a water bath thereby enhancing condensation of the evolved gases. Calibrated glass

receiving tube is affixed to each condensing tube with a rubber stopper to collect the water and

oil produced from the sample.

FEATURES

Sample bomb capacity 100 grams of crushed core material

Receiving tube capacity 20 ml (other size upon request)

Number of sample bomb / receiving tub 10

Max Temperature 650°C (1,200 °F)

Material carbon refractory steel

Weight 50 kg

Dimensions 1150 x 915 x 535 mm (45 x 36 x 21 in)

Electrical 220V, 50Hz

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

GAMMA RAY LOGGER (NGR 200)

The NGR200 core gamma ray logger provides both total and spectral analysis of the natural

gamma radiations emitted from the core samples upon arrival at the laboratory. It permits to

differentiate uranium, thorium and potassium concentrations. The data obtained with this

apparatus can be used to adjust the depth of the core to coincide with the open-hole logging

depths and to identify zones where core has been lost. The apparatus consists of a conveyer for

moving core, lead shielding to reduce background gamma radiation and a suitable gamma ray

detector. The detector system consists of a shielded scintillation crystal coupled with a photo

multiplier. Signals from the detector are processed using a multi channel spectrum analyzer and

analytical software. The gamma ray events are energy - sorted and counted over three energy

windows K, U and Th as well as the total gamma radiation. Core samples can be in barrel, in a

fibre glass, or aluminium, liner or exposed. The core is scanned along its length from bottom to

top simulating a wire-line log pass. The logging speed is adjustable to suit the core and data

requirements.

FEATURES

Belt length 3 meters

Suitable for core up to 5.5‟‟

Shielding area 5 & 3.7 cm around the crystal

Sodium Iodine detector 3” by 3”

Variable logging speed up to 5 feet / min

Power supply 230 VAC 50/60 Hz 1 phase

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

GEOMETRIC BULK VOLUME METER (GBV)

This instrument is designed to measure bulk volume of plug sized and/or full diameter core

samples with excellent accuracy. The principle consists of measuring accurately the length and

diameter of the samples at different grades. Minimum of 8 measurements along the diameter

and one every 50 mm along the length are necessary to get an accurate bulk volume

measurement. The bulk volume is determined by integrating those measurements. This

calculation can be done by hand or by optional computer program. In the latest, calipered

dimensional data on core samples are automatically logged and the geometric bulk volume,

shape factor, effective flow area and caliper bulk factor are automatically calculated by the

program.

FEATURES

A digital 150 mm caliper for plug cores with accuracy of +/- 0.02 mm

A digital 300 mm caliper for full diameter cores with accuracy of +/- 0.02 mm

A software to calculate the bulk volume parameters.

Electrical: 220V, 50Hz

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

IMMERSED BULK VOLUME METER (IBV)

The immersed bulk volume determination system is designed to measure bulk volume of plug

sized core samples with excellent accuracy. The principle consists of immersing the core sample

under mercury and measuring with a high precision weighing balance the resulting buoyant

force. The bulk volume is then determined by using the Archimede principle.

FEATURES

A robust base which supports the balance and a vertical post

An adjustable immersion depth and precision ram with level mark

A cradle which supports the sample when it is immerged in the mercury

A high precision balance with RS232 communication port

Reading accuracy: 0.01 g

Max weighing: 6,200 g

Repeatability: +/- 0.01 g

Linearity: +/- 0.01 g

A thermometer for mercury density determination

Mercury immersion bath

Electrical: 220V, 50Hz

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

MERCURY POROMETER

Tool designed to measure the gas space and bulk volume of a freshly recovered core sample.

The instrument consists of a hand operated pump, a sample cell equipped with a needle valve

mounted on its lid. The cell can accommodate a sample with a bulk volume of 10 to 15 cm3.

The mercury pump is equipped with a vernier calliper graduated in 0.01 cm3 increments. A

pressure gauge capable of indicating pressure up to 100 bar and a vacuum gauge are connected

to the system.

FEATURES

Max pressure 100 bar (1,500 psi)

Sample volume 10 to 15 cc

Cell size 40 x 70 mm

Pump volume 100 cc

Direct reading by vernier 0.01 cm3

Wetted part Stainless steel

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

HELIUM POROSIMETER (HEP)

The Helium gas expansion porosimeter is based on the Boyle‟s and Charles‟ law expansion of

helium gas and is used for direct grain volume and pore volume measurement in auxiliary cell at

isothermal conditions. Subsequently, porosity and grain density can be derived from the direct

measurements. A data acquisition computer allows for data logging and calculation of

parameters and also calibration data. The instrument measures grain volume of plug samples of

1” and 1.5” diameter. An optional full diameter matrix cup can be added for determination of

grain volume of whole diameter core samples. Each sample matrix cup is interchangeable and is

provided with stainless steel calibration check plugs. An auxiliary core holder for plug and

whole diameter core samples can also be used to measure pore volume at ambient or overburden

pressure.

FEATURES

Core diameter: 1” and 1.5”, (4” optional)

Core length: up to 3”, (up to 12” optional)

Porosity Range: up to 60%

Charge Pressure in reference volume: 200 psi

Pressure sensor accuracy: 0.1%

Porosity Range: up to 60%

Electrical requirements: 220 VAC, 50 Hz

N2/Helium requirements: 500 psi

Dry air requirements: 100 psi

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

HELIUM POROSIMETER FOR EDUCATIONAL PURPOSES

(HEP-E)

The Helium gas expansion porosimeter is based on the Boyle‟s and Charles‟ law expansion of

helium gas and is used for direct grain volume and pore volume measurement in auxiliary cell at

isothermal conditions. Subsequently, porosity and grain density can be derived from the direct

measurements. An excel spreadsheet calculation template allows for calculation of grain volume

and porosity.

FEATURES

Core diameter 1” and 1.5”

Core length up to 3"

Porosity Range up to 60%

Charge Pressure in reference volume 200 psi

Pressure sensor accuracy 0.1%


Electrical requirements 220 VAC, 50 Hz

N2/Helium requirements 500 psi

BENEFITS

Cost effective

Ideal for educational purposes

Compact system

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

STEADY STATE GAS PERMEAMETER (GASPERM)

The Gasperm instrument is dedicated to measure permeability to gas (air, nitrogen ...) of plug

sized core samples at room conditions and reservoir overburden pressure using the steady state

method. The instrument is designed for the injection of gas through the test sample at various

conditions of pressure and flow rates. The injection pressure at the core face is measured using a

pressure transducer and the gas flow rate is measured using one of the two precision mass flow

meters. The permeameter console can be configured with a precision pressure control valve to

vary the differential pressure and gas flow in the core which allows for the determination of slip

factor and Klinkenberg permeability versus reciprocal mean pressure relationship.

FEATURES

Permeability Range 0.01md to 10 darcies

Flow Pressure 0 to 100 psi

Gas flow 0-50, 0-2,000 cc/min

Temperature ambient

Temperature accuracy +/- 0.1 °C

Pressure transducer accuracy 0.1% F.S.

Diff. pressure transducer accuracy 0.25% F.S.

Flow accuracy 1 % F.S.

Nitrogen supply 250 psi

Power 220 VAC, 50 Hz

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

STEADY STATE GAS PERMEAMETER FOR EDUCATIONAL

PURPOSES (GPE30)

The educational gasperm instrument is dedicated to measure permeability to gas (air,

nitrogen,..) of plug sized core samples at room conditions and reservoir overburden pressure

using the steady state method. The instrument is designed for the injection of gas through the

test sample at various conditions of pressure and flow rates. The injection pressure at the core

face is measured using a pressure transducer and the gas flow rate is measured using a precision

mass flow metes. An excel spreadsheet calculation template allows for calculation of gas

permeability.

FEATURES

Permeability Range 1md to 1 darcy

Flow Pressure 0 to 30 psi

Gas flow 0-500 cc/min

Temperature ambient




Nitrogen supply 250 psi


BENEFITS

Cost effective


Compact system

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

WHOLE CORE STEADY STATE GAS PERMEAMETER

(WHOLEPERM)

The wholeperm instrument is dedicated to measure horizontal and vertical permeability to gas

(air, helium, nitrogen,..) of full size core samples at room conditions. The instrument is provided

with a gas permeameter console, a full size coreholder and a data acquisition computer station.

The air permeability determination is based on the steady state method. The instrument is

designed for the injection of gas through the test sample at various conditions of pressure and

flow rates. The injection pressure at the core face is measured using a pressure transducer and

the gas flow rate is measured using one of the two precision mass flow meters. The

permeameter console features a precision pressure metering valve to vary the pressure

differential and gas flow in the core which allows for the determination of slip factor and

Klinkenberg permeability versus reciprocal mean pressure relationship.

FEATURES

Permeability Range 0. 01md to 10 darcies

Flow Pressure 0 - 100 psi

Confining Pressure 0 - 400 psi

Gas flow 0-50 and 0-2,000 cc/min

Temperature ambient



Diff. Pressure transducer accuracy 0.25% F.S.


Core diameter 4” (other upon request)

Core length 3 to 6” (other upon request)

BENEFITS

Fast loading and unloading operation

Wide range of core diameter

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

STEADY STATE GAS PERMEAMETER AND POROSIMETER

(POROPERM)

The Poroperm instrument is dedicated to measure steady state gas permeability, Klinkenberg

permeability, pore volume and grain volume of plug sized core samples at room conditions. The

instrument is provided with a permeameter console, an hassler coreholder, a matrix cup and a

data acquisition computer station to be operated in manual and automatic mode. An optional

hydrostatic coreholder can be used to perform measurement at overburden pressure.

FEATURES

Permeability Range: 0.01md to 10 darcies

Flow Pressure: 0 - 200 psi

Confining Pressure: 0 - 400 psi

(option 10,000 psi)

Gas flow: 0-50 and 0-2,000 cc/min

Temperature: Ambient

Pressure transducer accuracy: 0.1% F.S.

Diff. Pressure transducer accuracy: 0.25% F.S.

Flow accuracy: 1 % F.S.

Core diameter: 1” and 1.5” (option)

Core length: Up to 3”

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

STEADY STATE GAS PERMEAMETER AND POROSIMETER

FOR EDUCATIONAL PURPOSE (POROPERM - E)

The educational poroperm instrument is dedicated to measure steady state gas permeability and

porosity of plug sized core samples at room conditions. The instrument is provided with a

permeameter console, an hassler coreholder, a matrix cup and a data acquisition computer

station to be operated in manual and automatic mode.

FEATURES

Permeability Range: 0.5 md to 5 darcies

Flow Pressure: 0 - 100 psi

Confining Pressure: 0 - 400 psi

Gas flow: 0-500 cc/min

Temperature: Ambient

Pressure transducer accuracy: 0.1% F.S.

Flow accuracy: 1 % F.S.

Core diameter: 1” and 1.5” (option)

Core length: Up to 3”

BENEFITS

Cost effective


Compact system

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CALIBRATED PERMEABILITY CHECK PLUGS

The check plugs are used to check and test the calibration of gas permeameters. The set consists

of five stainless steel check plugs with different permeability to air. The plug is made of a shell

that protects the porous media. These calibration plugs are not primary standards and have been

tested using customary testing methods.

FEATURES

Diameter 1.0 inch, 1.5 inch, 30 mm, 50 mm (other upon request)

Length 1.0 inch

Permeability range 0.05 -0.15 md, 0.7-2md, 8-15 md,40-70md, 150-220 md

Porosity range 2 to 35 %

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

UNSTEADY STATE GAS PERMEAMETER AND

POROSIMETER AT MODERATE CONFINING PRESSURE

(COREVAL 30)

The Coreval 30 instrument is dedicated to measure the porosity and permeability to helium of

plug sized core samples at a fixed confining pressure of 400 psi maximum. The instrument is

provided with a data acquisition and calculation computer station. Permeability measurements

are made using the unsteady state pressure drop method. This data is used to determine the

equivalent liquid permeability, slip and turbulence factors. Equivalent air permeability at a user

specified pressure is also computed. Porosity and pore volume measurements are made using

the Boyle‟s and Charles‟ law technique.

FEATURES



Pore Pressure 250 psi

Confining pressure up to 400 psi

Temperature ambient



Helium 400 psi

N2 500 psi

Air 100 psi (dry)


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

UNSTEADY STATE GAS PERMEAMETER AND

POROSIMETER AT OVERBURDEN PRESSURE

(COREVAL 700)

The Coreval 700 instrument is dedicated to measure the porosity and permeability to helium

of plug sized core samples at multiple confining pressures ranging from 400 psi to 10,000 psi.

The instrument is provided with a data acquisition and calculation computer station.

Permeability measurements are made using the unsteady state pressure drop method. This data

is used to determine the equivalent liquid permeability, slip and turbulence factors. Equivalent

air permeability at a user specified pressure is also computed. Porosity and pore volume

measurements are made using the Boyle‟s and Charles‟ law technique.

FEATURES




Confining Pressure 400 psi to 10,000 psi

Temperature ambient



Helium 400 psi

Air 100 psi (dry)


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

AUTOMATED SAMPLE LOADING UNSTEADY STATE

PERMEAMETER AND POROSIMETER AT OVERBURDEN

PRESSURE (KEYPHI)

The KEYPHI instrument is a fully automated permeameter and porosimeter used to determine

properties of plug sized core samples at reservoir confining pressure. The gas permeability

determination is based on the unsteady state pressure falloff method whereas the pore volume is

determined using the Boyles law technique. The instrument is provided with a unique automatic

core sample loading mechanism which can process multiple samples without any human

intervention. In addition, the instrument offers reporting and calculation facilities thanks to its

user-friendly windows operated software. Klinkenberg slip factor “b”, Klinkenberg corrected

permeability, inertial coefficients, sample bulk volume, sample porosity, grain volume are

automatically determined and presented on customised report.

FEATURES

Confining Pressure 400-10,000 psi


Core diameter 1" or 1.5"

Core length 0.75" to 3"

Permeability Range <0.001 to >10,000 md

Porosity Range 0.1 > 40%

Sample capacity 13 (1.5” diam. samples) and 16 (1” diam. Sample)

Helium 400 psi

Air 125 psi (dry)


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

LIQUID PERMEAMETER (LIQPERM)

The Liquid permeameter is dedicated to measure permeability to liquid of plug sized core

samples at room conditions. The liquid permeability determination is based on the Darcy‟s law

and assumes that one phase is present in the core and there is no rock fluid interaction. The

instrument is provided with a hassler coreholder, a transparent fluid vessel, a console with

pressure digital display, 3 interchangeable burettes for various permeability ranges, an

electronic timer for flow rate calculation and an Excel spread sheet calculation template. This

low cost apparatus is particular interested for educational purposes.

FEATURES

Permeability Range 0. 1md to 5 darcy

Flow Pressure up to 100 psi

Confining pressure up to 400 psi

Temperature ambient


Air supply 250 psi


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

BENCH TOP PERMEABILITY SYSTEM (BPS 350)

The BPS350 permeameter is a manually operated system designed for performing simple

permeability tests at pore pressure to 5,000 psi with confining pressures to 10,000 psi. The

standard system includes a low pulsation HPLC pump for fluid delivery at flow rates from 0.01

to 10 ml/min. Plug core samples are held in a hassler coreholder mounted horizontally. The core

holder can accommodate 1.5” diameter core samples one to three inches in length. The system

is equipped with one differential pressure transducers and digital readout which has a range of

0-250 psid. A manual bypass valve is used to equilibrate pressure on the transducer preventing

damage at high differential pressures. A dome loaded backpressure regulator is utilized to

maintain downstream elevated test pressures. A manually operated hydraulic pump is used to

generate confining pressure up to 10,000 psi. An optional gas injection can be added to flow

nitrogen gas through the core sample to measure gas permeability.

FEATURES

Confining pressure 700 bar (10,000psi)

Pore pressure 350 bar (5,000psi)

Temperature ambient

Core diameter 1” or 1‟‟1/2

Core length 1‟‟ to 3‟‟

Loading type Hassler

Wetted material stainless steel

Fluid Water and N2


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

BENCH TOP UNSTEADY STATE RELATIVE PERMEAMETER

(BRP 350)

The semi automated BRP350 allows for the determination of liquid permeability and liquid /

liquid relative permeability on plug sized core samples at overburden pressure. The test consists

of direct measurement of permeability while injecting oil, water or brine through the rock

sample. The system includes two floating piston accumulators, a HPLC pump, a hassler

coreholder, an overburden pump, a back pressure regulator and pressure display. The instrument

can also be configured for gas / liquid relative permeability measurement.

FEATURES



Temperature ambient



Loading type Hassler


N2 2,000 psi


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

BENCH TOP UNSTEADY & STEADY STATE LIQUID – LIQUID

RELATIVE PERMEAMETER (SRP 350)

The SRP350 relative permeameter allows for determination of the liquid / liquid relative

permeability on plug sized core samples at overburden pressure using unsteady and steady state

conditions. The core saturation is determined by measuring the resistivity of the core sample

during the flow test. The flow rates are controlled by the two pumps used to inject

simultaneously the fluids is the core sample.

FEATURES



Temperature ambient



Loading type Hydrostatic


N2 2,000 psi


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

ELECTRICAL PROPERTIES SYSTEM @ AMBIENT

CONDITIONS (EPS-A)

Complete system used for the determination of resistivity and formation factor of plug sized

sample at ambient conditions. The system permits to measure the rock resistivity Ro and the

brine resistivity Rw at different frequencies. The cell utilises a two and four electrode design.

The platens contact the core end faces under a constant pneumatic pressure up to 6 bar. This

minimises contact resistance artefacts which are often found where a screw or jack mechanism

is used to load the sample onto the electrode platens. The cell is provided with a plastic cover

box to minimise core saturation changes. The instrument also includes a dip conductivity probe

and a becher to measure the brine resistivity. An LCR meter is used to monitor the core and

brine resistance and capacitance.

FEATURES


Core Length up to 3”

Resistivity measurement 2 and 4 electrodes

Max pressure Atmospheric

Temperature Room condition


Air 150 psi

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

ELECTRICAL PROPERTIES SYSTEM @ OVERBURDEN

PRESSURE (EPS 700)

The EPS 700 is used for the measurement of rock resistivity for both fully and partially brine

saturated core samples at overburden pressure. The system includes a hydrostatic electrical

coreholder, with hand pump for confining pressure generation, a pore pressure control panel for

core desaturation and a resistivity meter for 2 and 4 points core resistance measurement. The

system can be configured for multi sample configurations.

FEATURES


Core Length up to 3”

Resistivity measurement 2 and 4 electrodes

Overburden pressure 700 bar (10,000 psi)

Temperature Room condition


Air 150 psi

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

EDUCATIONAL CAPILLARY PRESSURE CELL

The educational capillary pressure cell enables to desaturate one consolidated core sample by

the porous plate method. Data obtained can be used to calculate capillary pressure versus

saturation curves. A high precision weighing balance can be used for core saturation

measurement. The capillary pressure cell is manufactured from stainless steel and at its base is

equipped with a ceramic plate used as a semi permeable porous plate. The desaturation cell

consists of a pressure vessel, with an easy opening lid, o‟rings seals, outflow tube assemblies

and pressure control panel. A ceramic plate is provided with the cell withstanding 10 bar

pressure. The control panel includes a digital pressure display, two low and high range pressure

regulators and a set of control valves.

FEATURES

Diameter 40 mm

Height 80 mm

Maximum desaturation process 200 psi

Minimum desaturation process 0.1 psi

Ceramic plate pressure 10 bar



Air Pressure requirements 0- 150 psi (10 bar)

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

MULTI SAMPLE CAPILLARY PRESSURE CELL

The multiple sample desaturation cell enables to desaturate a set of consolidated core samples

by the porous plate method. Data obtained can be used to calculate capillary pressure versus

saturation curves. A high precision weighing balance can be used for core saturation

measurement. The multiple sample desaturation cell is manufactured from stainless steel and is

equipped at its base with a large ceramic plate used as a semi permeable porous plate. The

desaturation cell consists of a pressure vessel, with an easy opening lid, clamping bolts, o‟rings

seals, outflow tube assemblies and pressure control panel. Three ceramic plates are provided

with the systems withstanding each 3 bar, 5 bar and 15 bar pressure. The control panel includes

a digital pressure display, two low and high range pressure regulators and a set of control

valves. A gas humidifier is also provided to insure minimum evaporation during the

desaturation process.

FEATURES

Diameter 300 mm

Maximum desaturation process 200 psi

Minimum desaturation process 0.1 psi

Ceramic plate pressure 3 bar, 5 bar and 15 bar



Air Pressure requirements 0- 200 psi (15 bar)

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CAPILLARY PRESSURE REFRIGERATED CENTRIFUGE

(RC4500)

The RC4500 is a refrigerated centrifuge modified to enable rapid determination of capillary

pressure characteristics on six core samples simultaneously. It can also be utilized for rapid

sample preparation to restore state conditions for subsequent testing in various test equipment.

Custom designed sample chambers offer the ability to spin core plug samples up to 1.5 inches in

diameter at rotational speeds up to 4,500 RPM. It includes a rotor and drainage cells which can

accommodate either 1”, or 1.5” diameter cores. A digital speed control with the ability to ramp

speeds at specified intervals and a precision temperature control system is included. An over-

temperature setpoint stops the centrifuge if the temperature exceeds the setpoint by a specified

value. The system is also equipped with a sensor for rotor imbalance. It is equipped with a

digital camera system that allows to user to measure the displaced fluid volumes in each of the

cells sequentially.

FEATURES

PC range :

Oil-water drainage : 0 to 6.2 bar (+90 psi)

Oil-water imbibition: 0 to -8.4 bar (– 121 psi)

Air-water drainage: 0 to 20.9 bar (+303 psi)

Air-water imbibition: 0 to -28.1 bar (– 407 psi)

Speed regulation: ± 1 rpm

Temperature: 5°C (@speed = 0) to +90°C

Speed: from 200 up to 4,500 RPM

Large radius: 26 cm

Power supply: 400 V 3 ~ + N

BENEFITS

Fast capillary pressure run (1 to 2 days)

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CAPILLARY PRESSURE MERCURY SYSTEM (CPM 140)

Manual operated system for the measurement of capillary pressure and pore morphology. Based

on Purcell method, mercury is injected into plug sized samples at know volume from vacuum to

2,000 psi (140 bar). The instrument uses a hand operated pump for mercury injection and a

coreholder equipped with an opening windowed chamber cap for easy loading / unloading

operations and mercury level visualization. The control panel includes the pore pressure

regulator, the pore pressure transducer with the digital display and a vacuum manometer.

FEATURES

Pressure range up to 140 bar (2,000 psi)

Temperature ambient

Core Diameter 1” or 1.5”

Core length up to 3 inches

Vacuum pumping speed 2.5 m3/h

Final vacuum pressure 10-3

mbar.

Power supply 220 VAC, 50Hz

Nitrogen source 2,000 psi

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

DIGITAL CORE PHOTOGRAPHY SYSTEM (DCP)

The fully automated core photography system is designed for complete core photography and

archiving purposes, producing high quality white and ultraviolet colour images of full diameter

whole or slabbed core samples. The operator positions the core samples on a four rows rack and

a digital camera mounted above the core samples under white or ultra violet lighting takes a

high resolution picture. The images are then automatically digitised, displayed and recorded in

the high speed computer. The software includes calibration functions for the camera, image

processing capabilities as well as file compression, storage and transfer facilities. The

innovative concept is in the use of a digital camera which can produce very high resolution

color images up, avoiding the risk of deformed images.

FEATURES

Camera type 35 mm Full frame

Camera resolution 5616 x 3744 pixels

File size 21 Megapixels

Interface USB

Internal PC hard drive 80 GB

Maximum frame area 600 mm x 900 mm

Data storage on CDROM RAW, JPG

Weight 200 kg

Power supply 220 VAC , 50 Hz

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

SPECIAL CORE ANALYSIS

Core Flood System

Formation Damage

Capri

Rock Compressibility

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CORE FLOOD SYSTEM FOR EOR STUDIES (CFS 700)

The CFS 700 system provides a versatile facility to carry out core flood and fluid flow tests

studies at reservoir conditions of temperature and pressure. The core flood and fluid tests allow

for the evaluation of the effect of different fluids on rock permeability such as brine sensitivity,

return permeability, critical flow velocity, acid stimulation, EOR tests (secondary and tertiary

water flooding, polymer injection). The computer controlled system is provided with a unique

software that allows for operation both manual and automatic modes where all key components

can be controlled including pump, valves, video capturing and data acquisition. A test sequencer

also permits to program and run test sequences automatically. The coreholder, air operated

valves, produced fluid separator if selected and necessary plumbing are mounted in an airbath

that has been designed to provide easy access of all components. Several features can be used

to extend the capabilities of the system. Among them, the automated back pressure regulator

provides a very stable pressure control with fast response to pressure fluctuations and phase

transition. It can be used for single and multiphase flow system. The automatic confining pump

generates and maintains automatically a net overburden pressure thus avoiding to control

pressure changes during heating and cooling steps. The unique video separator provides an

extreme accuracy of the volume of brine, oil and gas produced during the flow tests at reservoir

conditions.

FEATURES

Confining pressure 700 bar (10,000 psi )

Pore pressure depends on the injection pump model

Maximum working temperature 150°C

Core diameter 1.5” other upon request

Core length 1”to 3” other upon request

Fluid flow rate depends on the injection pump model

Wetted parts Stainless steel, other type upon request

Power supply 220VAC, 50Hz

Air Pressure requirements 7 bar (100 psi)

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

UNSTEADY STATE RELATIVE PERMEAMETER

(AUTOFLOOD 700)

The AUTOFLOOD 700 system provides a versatile facility to carry out unsteady state relative

permeability studies for liquid/liquid and liquid/gas at reservoir conditions of temperature and

pressure. The standard configuration allows for liquid /liquid tests at constant flow rate and

liquid/gas tests at constant pressure. A gas line permits to inject gas at constant pressure. The

computer controlled system is provided with a unique software that allows for operation both

manual and automatic modes where all key components can be controlled including pump,

valves, video capturing and data acquisition. A test sequencer also permits to program and run

test sequences automatically. The coreholder, air operated valves, produced fluid separator and

necessary plumbing are mounted in an airbath that has been designed to provide easy access of

all components. The automated back pressure regulator provides a very stable pressure control

with fast response to pressure fluctuations and phase transition. It can be used for single and

multiphase flow system. The automatic confining pump generates and maintains automatically a

net overburden pressure thus avoiding to control pressure changes during heating and cooling

steps. The unique video separator provides an extreme accuracy of the volume of brine, oil and

gas produced during the flow tests at reservoir conditions.

FEATURES

Maximum confining pressure 700 bar (10,000 psi)

Maximum pore pressure 700 bar (10,000 psi)

Maximum gas pressure 200 bar (3,000 psi)


Core diameter 1"1/2 other upon request

Core length 1” to 3” other upon request

Material Stainless steel



VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

STEADY STATE AND UNSTEADY STATE RELATIVE

PERMEAMETER SYSTEM (RPS 700)

The RPS 700 system provides a versatile facility to carry out unsteady state and steady state

relative permeability studies for liquid/liquid and liquid/gas at reservoir conditions of

temperature and pressure. The standard configuration allows liquid /liquid and liquid/gas flow

tests to be conducted at constant flow rate. An optional gas line permits to run unsteady state

gas/liquid permeability tests at constant pressure. The computer controlled system is provided

with a unique software that allows for operation both manual and automatic modes where all

key components can be controlled including pump, valves, video capturing and data acquisition.

A test sequencer also permits to program and run test sequences automatically. The coreholder,

air operated valves, produced fluid separator and necessary plumbing are mounted in an airbath

that has been designed to provide easy access of all components. The unique high temperature

recirculating triple pump system presents an unprecedented solution to generate continuous,

pulse free fluid flow rate of one or more fluids through a sample while maintaining a constant

pressure at the outlet of the sample. The automatic confining pump generates and maintains

automatically a net overburden pressure thus avoiding to control pressure changes during

heating and cooling steps. The video separator also provides an extreme accuracy of the volume

of brine, oil and gas produced during the flow tests at reservoir conditions.

FEATURES




Core diameter 1"1/2 other upon request


Flow rate 0.005 to 50 cc/min




VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

XRAY SCANNER FOR IN-SITU SATURATION MONITORING

The Xray scanner is an add-on module to the relative permeability RPS700 rig and allows for

monitoring the in situ fluid saturations and distribution along the length of the core. The

standard configuration allows for liquid /liquid and liquid/gas saturation determination. The X-

ray scanner allows for measuring the attenuation of an X-ray beam sent through a core sample

to determine the phase saturation and saturation distribution along the length of the core sample.

The X-ray detector and generator are mounted on a motor driven table equipped with a high

accuracy position encoder. A composite coreholder is be used for these tests to avoid X-ray

absorption.

FEATURES


Maximum pore pressure 700 bar (10,000psi)


Core diameter 1”5 other upon request


X-ray source 120 kV, 4 mA




BENEFITS

The core sample temperature is homogenous all along the core.

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

FORMATION DAMAGE AND WELL TREATMENT

EVALUATION SYSTEM (FDS 350)

The FDS350 system enables to perform (a) liquid permeability measurement, (b) static filtration

tests, (c) mud invasion evaluation and (d) stimulation tests on a formation sample at reservoir

conditions of temperature and pressure. This instrument can be configured for the evaluation of

the effect of different fluids on rock permeability such as drilling fluids (water-based or oil-

based mud), cement effluents, chemical wash treating fluids and acid corrosive treating fluids.

Initial permeability, return permeability, brine sensitivity, critical flow velocity, acid

stimulation, mud filtrate invasion can be monitored with this system. Drilling mud tests are

performed under realistic field conditions by flowing the fluids tangentially to the face of the

core, thanks to a special leak-off core holder. The system can be configured with a mud

recirculation pump to perform dynamic filtration tests so as to study erosion effects induced by

the fluid flowing across the core face which contains proppant and other particulates. The mud

pump flow rate of 6 l/min max ensures an efficient shear rate to simulate the real operating

conditions. The computer controlled system is provided with a unique software that allows for

operation both manual and automatic modes where all key components can be controlled

including pump, valves and data acquisition. A test sequencer also permits to program and run

test sequences automatically. The coreholder, air operated valves, mud pump and necessary

plumbing are mounted in an airbath that has been designed to provide easy access of all

components.

FEATURES



Maximum mud pressure 350 bar (5,000 psi)


Core diameter 1.5” other upon request

Core length 2 to 4” other upon request

Mud flow rate up to 6 liter/min (option)

Material Stainless steel, Titanium, hastelloy



VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CAPILLARY PRESSURE AND RESISTIVITY INDEX SYSTEM

(CAPRI)

The CAPRI system is dedicated to the determination of the capillary pressure curves (positive

and negative) and the electrical resistivity index as a function of core sample saturation at

reservoir conditions. Saturation exponent “n”, formation factor and cementation exponent “m”

are also calculated. The instrument consists of a core holder furnished with hydrophobic and

hydrophilic ceramics and electrodes pattern for resistivity measurement, an automated pumping

system for fluid control and a resistivity cell for brine resistivity measurement. The whole is

housed in a temperature controlled air bath.

FEATURES

Maximum confining pressure 700 bar (10, 000 psi)

Max pore pressure 700 bar (10,000 psi)

Working temperature up to 150°C

Capillary pressure range 10 to +10 bar (145 psi)

Core length 2” up to 3”

Core diameter 1 ½” other upon request


Brine wetted material stainless steel

BENEFITS

Measurement are made at reservoir conditions of pressure and temperature

Direct capillary pressure measurement

High temperature pump located in the controlled temperature air bath to reduce volume measurement

error induced by temperature fluctuations.

Multiple core samples configuration available

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

ROCK COMPRESSIBILITY SYSTEM (RCS 700)

The RCS 700 apparatus is designed to monitor pore and bulk volume changes under various

levels of radial and axial confining pressures at reservoir temperature. The apparatus consists of

a triaxial core holder located in a constant temperature air bath to restore the reservoir

conditions on the core sample. The pump cylinder is used to generate and control the pore

pressure while the other two pump cylinders are used to generate the axial and radial confining

pressures. The volume variations of fluid injected into or expelled from the core sample can be

monitored with an extreme accuracy. Automated tests can be programmed to perform a number

of measurements at different steps of pressure and temperature without user‟s intervention.

FEATURES

Core Diameter 1 1/2" other upon request

Core Length 1 to 3” other upon request

Max pore pressure 700 bar (10,000 psi)

Max axial / radial confining pressure 700 bar (10,000 psi)

Stroke volume of pump 100 cc

Working temperature ambient to 150° C

Volume measurement accuracy 0.001 cc

Pressure measurement accuracy 0.1 %



VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

ATMOSPHERIC ACOUSTIC VELOCITY SYSTEM (AVS A)

The AVS A allows for the measurement of acoustic velocity of a core sample at atmospheric

pressure and ambient temperature. It is used to propagate compressional and shear waves

through core samples, calculate acoustic velocity and determine dynamic elastic constants such

as the dynamic moduli, Young‟s, bulk and shear, along with Poisson‟s ratio. The system

consists of an atmospheric coreholder, acoustic transducer assemblies, acoustic Pulser / receiver

and digital oscilloscope.

FEATURES

Operating pressure Atmospheric

Operating temperature up to 50°C

Core sample diameter 1” and 1.5” other upon request

Core sample length 1 to 3” other upon request

Center frequency 500 KHz

Mode compressional (P) and shear (S1 & S2)


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

OVERBURDEN ACOUSTIC VELOCITY SYSTEM (AVS 700)

The AVS 700 allows for the measurement of acoustic velocity of a core sample under a wide

range of pore and confining pressures. It is used to propagate compressional and shear waves

through core samples, measure pore pressure, confining pressure and temperature, calculate

acoustic velocity and determine dynamic elastic constants such as the dynamic moduli,

Young‟s, bulk and shear, along with Poisson‟s ratio. The system consists of fully equipped

pressure vessel, acoustic transducer assemblies, confining pressure controller, pore pressure

controller, acoustic Pulser / receiver and digital oscilloscope.

FEATURES

Operating pressure Up to 700 bar (10,000 psi)


Core sample diameter 1.5” other upon request





VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

AUTOMATED HP-HT ACOUSTIC VELOCITY SYSTEM

(AVS 700-HT)

The AVS 700-HT apparatus allows for the measurement of acoustic velocity of a core sample

under various levels of pore pressure and radial/axial confining pressures at reservoir

temperature. The apparatus permits to propagate compressional and shear waves S1 and S2

through core samples, generate and measure the pore pressure and confining pressure, calculate

acoustic velocity at reservoir conditions and determine dynamic elastic constants (Poisson ratio

and Young modulus). The system consists of three automated pumps and a fully equipped

acoustic triaxial coreholder housed in a constant temperature air bath to restore the reservoir

conditions on the core sample. One pump cylinder is used to generate and control the pore

pressure while the other two pump cylinders are used to generate the axial and radial confining

pressures. A pulser-receiver is used to produce an electrical pulse to excite a piezoelectric

transducer and an oscilloscope measures the travel time of the pulse between the two

transducers. This data is then used to calculate the acoustic velocity of the core sample.

FEATURES

Operating pressure Up to 700 bar (10,000 psi)


Core sample diameter 1.5” other upon request





VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

AGING CELL APPARATUS (ACA 700)

The apparatus is designed for aging core samples with crude oil so as to restore its reservoir

wettability before being used for a SCAL study. The base version is delivered with five core

units. The aging method entails first saturating a cleaned (and thus water wet) core plug with

brine. The brine is then displaced by crude oil until representative initial water saturation is

achieved. During this process the smaller pores remain water –filled, whereas the oil invades the

remainder of the pore space, leaving thin water films on the pore walls and in crevices. Finally,

the core containing crude oil and connate water is left for many weeks at reservoir temperature

and pressure. It is at this stage that wettability changes may occur in the oil-invaded pores.

However, these changes are dependant upon the stability of the water wet films, trapped

between the rock surface and the oil. The pore walls can only become oil-wet if contacted by oil

due to the rupture of these films. In this case the core will have achieved a mixed wettability

state status.

FEATURES

Operating pressure up to 700 bar (10,000 psi)


Core sample diameter 1” and 1.5”

Core sample length 1 to 3”

Fluid flow rate up to 10 cc/min

Wetted part Stainless steel

Air requirement 2,000 psi


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

COREHOLDERS

Hassler CH

Triaxial CH

Leakoff CH

Stands

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

HASSLER COREHOLDER (HAS SERIES)

The HAC Series core holders are standard Hassler type core holders used for fluid flow testing.

With the coreholder assembled and the sleeve in place the core is inserted into the loading end.

The platen is then pushed in and held in place by the cap which can be screwed on by hand and

allows 50 mm adjustement. Further adjustment is possible with the use of interchangeable

spacers fitted to the loose platen. An inlet and outlet distribution plug allows fluids and gases to

be injected through the core sample. A unique feature of the HAC series core holder is that the

sleeve remains in place and the core is loaded from one end without having to drain or refill the

confining fluid. By releasing the confining radial pressure and unscrewing the end plug, the core

sample can be easily removed without exposing it to the annulus fluid. The core holders can be

provided to have interchangeable core diameters.

FEATURES

Performance specifications

HAC series

Operating pressure rating:

Operating temperature:

Fitting:

Core diameter:

Core length:

Wetted parts:

Sleeve material

Inlet port:

Outlet port:

5,000 psi (Max)

Ambient or 150°C

NPT, Autoclave or HIP

Customer specified

Customer specified

Stainless steel, Hastelloy, titanium

Viton

As request

As request

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

HYDROSTATIC COREHOLDER (HYC SERIES)

The HYC Series core holders are standard hydrostatic type core holders in which radial and

axial confining pressures are common. These core holders are routinely used for gas and liquid

permeability testing and water flooding experiments. The coreholder has a fixed platen at one

end over which the rubber sleeve is mounted and located in the other end of the sleeve is a

floating platen connected via a ¼” diameter tubing passing through the outside. For variable

length cores, this design insures solid contact between the platen and core sample. To change a

core sample the confining fluid must be drained off and the knurled screwed ring removed by

rotating anti clockwise by hand. This will withdraw the fixed platen together with the sleeve,

core and floating platen. After removal of the two platens from the sleeve the core can be

withdrawn. Loading a new core sample is carried out in the reverse order. The advantage of this

type of coreholder is that the overburden pressure acts on the end of the core as well as the

diameter. The coreholder can be equipped with a number of pressure taps molded in the sleeve

at discrete locations required by the end user. This design allow to monitor the pressure drop

along the length of the core sample during fluid flow tests. Electrical pressure tap can also be

provided to monitor the resistivity of the core sample during a permeability test.

FEATURES


HYC series



Fitting:

Core diameter:

Core length:

Wetted parts:

Sleeve material :

Inlet port:

Outlet port:

Pressure tap :

5,000, 10,000 psi, 15,000 psi

Up to 150°C


Customer specified

Customer specified


Viton

As request

one

As request

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

TRIAXIAL COREHOLDER (TRC SERIES)

The TRC Series core holders are standard triaxial type core holders in which radial and axial

loading are independent. These core holders are routinely used for fluid flow experiments. A

unique feature of the TRC series core holder is that the sleeve remains in place and the core is

loaded from one end without having to drain or refill the confining fluid. Independent axial

pressure is applied via a floating distribution plug. An inlet and outlet distribution plug allows

fluids and gases to be injected through the core sample. A unique feature of the TRC Series core

holder is that the holder does not need to be completely disassembled to remove the core

sample. By releasing the confining radial and axial pressure and unscrewing the eng plug, the

core sample can be easily removed without exposing it to the annulus fluid. The coreholder can

be configured for hassler loading, hydrostatic loading or triaxial loading.

FEATURES


TRC series



Fitting:

Core diameter:

Core length:

Wetted parts:

Sleeve material :

Inlet port:

Outlet port:

5,000, 10,000 psi, 15,000 psi

Up to 150°C


Customer specified

Customer specified


Viton

As request

As request

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

LEAKOFF COREHOLDER (LEC SERIES)

The LEC Series core holders are mainly used for static and dynamic filtration tests so as to

study erosion effects induced by the fluid flowing across the core face which contains proppant

and other particulates. The coreholder features a special head that allows the upper face of the

core sample to be exposed to invasion fluids. The fluids can be injected from both ends of the

core holder then simulating the wellbore and the reservoir side. The coreholder can be equipped

with a number of pressure taps molded in the sleeve at discrete locations required by the end

user. This design allow to monitor the pressure drop along the length of the core sample during

fluid flow tests.

.

FEATURES


LEC series



Fitting:

Core diameter:

Core length:

Wetted parts:

Sleeve material :

Inlet port:

Outlet port:

Pressure taps :

5,000, 10,000 psi

Up to 150°C

NPT

Customer specified

Customer specified


Viton

As request

As request

As request

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

QUICK RELEASE COREHOLDER (QRC SERIES)

The QRC Series core holders allows for the core to be loaded without the complete disassembly

of the coreholder. The core loading is achieved using an innovative ¼ turn fast release bayonet

mechanism. The coreholder is configured for hassler loading. The sleeve remains in place and

the core is loaded from one end without having to drain/refill the confining fluid which can be

nitrogen or hydraulic oil. This avoids damage to the sleeve which can occur with assembly and

disassembly. Operation is much easier and quicker and leads to higher throughput when tests of

short duration are being carried out.

FEATURES


QRC series



Fitting:

Core diameter:

Core length:

Wetted parts:

Sleeve material

Inlet port:

Outlet port:

400 psi, 1000 psi

Ambient or up to 80°C

NPT

Customer specified

Customer specified

Stainless steel

Nitrile

1

1

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

TRANSPARENT COMPOSITE COREHOLDER (TCC SERIES)

The TCC Series core holders are standard hydrostatic type core holders. These core holders are

used for gas and liquid permeability testing with in situ saturation monitoring. The core holder

uses a thin aluminium liner which is over wrapped with carbon fibre composite and epoxy to

avoid important loss of X-ray. Spiral fluid distribution grooves on core inlet are incorporated to

minimise capillary end effects. The coreholder can be provided with an heating system which

heats and re-circulates the confining fluid through the annular confining chamber for optimal

temperature homogeneity.

FEATURES


TCC series



Fitting:

Core diameter:

Core length:

Wetted parts:

Sleeve material

Inlet port:

Outlet port:

Up to 10,000 psi,

Ambient or up to 150°C

NPT

Customer specified

Customer specified


Viton

As request

As request

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

ACOUSTIC VELOCITY COREHOLDER (AVC SERIES)

The AVC Series core holders are standard triaxial type core holders in which radial and axial

loading are independent. These core holders are routinely used for acoustic velocity

measurement at reservoir conditions. The coreholder features a pair of acoustic transducers that

propagate compressional and two plane-polarized shear waves through the core sample. The

triaxial loading insures a proper surface contact between the transducer and the core. An inlet

and outlet distribution plug allows fluids to be injected through the core sample. The coreholder

does not need to be completely disassembled to remove the core sample. A tool permits to

orientate easily the P&S1,S2 transducer before the acoustic velocity measurement takes place.

FEATURES


AVC series



Center frequency

Fitting:

Core diameter:

Core length:

Wetted parts:

Sleeve material

Inlet port:

Outlet port:

10,000 psi, 15,000 psi

Ambient or 150°C

500 KHz


Customer specified

Customer specified

Stainless steel

Viton

1

1

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

ELECTRICAL RESISTIVITY AND CAPILLARY PRESSURE

COREHOLDER (ECP SERIES)

The ECP Series core holders are standard hydrostatic type core holders. These core holders are

routinely used for electrical resistivity and capillary pressure at reservoir conditions. The

coreholders feature both water wet and oil wet porous ceramics placed between the flow

distribution plugs and the core sample. Four electrodes have been molded directly into the

sleeves and are used to measure the resistivity of the sample. Two of them are provided with

metal ring placed into the sleeve along the core length at one inch spacing between the rings.

The other two electrodes are in contact with the distribution plugs which are electrically isolated

from the rest of the coreholder.

FEATURES


ECP series



Resistivity measurement

Capillary pressure

Connection

Core diameter:

Core length:

Wetted parts:

Sleeve material

Inlet port:

Outlet port:

10,000 psi,

Ambient and up to 150°C

2 and 4 points

Positive and negative

NPT

Customer specified

Customer specified

Stainless steel

Viton

2

1

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

HEATING SYSTEM (HES SERIES)

The electrical heating system can be provided to heat and maintain homogeneous temperature in

the core sample. The system uses two half heating shelves maintained by two clamps that fit

the shape of the coreholder in order to provide the highest heat efficiency. A digital temperature

controller is used to enter, display and regulate the temperature . A thermocouple probe is used

to measure the temperature of the coreholder body.

FEATURES


HES series


Temperature accuracy:

Power:

Ambient to 150°C

0.1 °C

220 VAC, 50 Hz,

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

STANDS (STA SERIES)

A number of stands are available depending on the End user‟s requirement. Simple to most

complicated designs can be proposed. The stand can be mounted inside or outside of the airbath.

The stand can also be configured in a bench top or bench floor version.

FEATURES


STA series

Coreholder position:


Fixed Horizontal,

Fixed horizontal and vertical,

Swivelling

Ambient and up to 150°C

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CORE ANALYSIS COMPONENTS

Level Tracker

BPR

Vacuum Pump

Pressure Generator

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

LEVEL TRACKER SEPARATOR (LTS SERIES)

Designed to measure the volume of liquid produced during a process at ambient conditions. The

device is made of a precision bore calibrated glass liquid collector, a motor driven level detector

composed of a tracking fork with 2 optical fibers (light path of emitter and sensor) and a

converter (light / voltage), an encoder to log the liquid level and a computer interface to control

the instrument and to log and display the liquid volume versus time.

FEATURES

Temperature ambient

Collector capacity 100 ml or 300 ml

Volume accuracy 0.1 ml

Wetted parts glass

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

DUAL LEVEL TRACKER (DLT SERIES)

Designed to measure the volumes of the two liquid phases produced during a process at ambient

conditions. The device is made of a precision bore calibrated glass liquid collector and two

motor driven level detector used to monitor the first water / oil interface and the second oil / Gas

interface. Each detector is composed of a tracking fork with 2 optical fibers (light path of

emitter and sensor) and a converter (light / voltage), an encoder to log the liquid level and a

computer interface to control the instrument and to log and display the liquid volume versus

time.

FEATURES

Temperature ambient

Collector capacity 100 ml or 300 ml

Volume accuracy 0.1 ml

Wetted parts glass


Weight 30 kg

Dimensions (HxWxL) 800 mm x 250 mm x 250 mm

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

AMBIENT CONDITIONS TWO PHASE VIDEO SEPARATOR

(VSE -A)

The video separator is a precision device used for separating and determining the oil, brine or

gas volumes that are produced from a core sample during a two phase relative permeability test.

It consists of a separation bore used for collecting and separating produced fluids under gravity

and a measurement bore used for visualising the two phases fluid interface at room conditions.

The measurement bore consists of a glass tube to allow for sample visibility. Placing a light

behind the tube allows easy discernment of the two phases interface level. Measurement of

produced fluids during the displacement test is performed with a video camera which monitors

the position of the interface of the two fluids produced from the core sample in the measurement

bore of the separator. The position of the interface is directly proportional of the volumes of

fluids produced from the core sample and so of the change in the core saturation. The high

resolution camera is equipped with an integrated zoom and a back lighting installed in the rear

side of the tube. The camera is connected to the computer station so that the image of the fluid

can be displayed and recorded on the PC. The video software incorporates facilities which

enable to detect automatically the liquid/ liquid and gas/ liquid interface and so derive the

volumes of produced fluids from the core and so the changes in the core saturation.

FEATURES

Max pressure ………………… Atmospheric pressure

Max temperature……………… up to 40 °C

Max volume change………….. 30 ml

Volume accuracy…………...… 0.01 ml

Material………………………. Glassware

Measurement resolution…….. 0.02 mm

Minimum field of view………. 50 mm

CDD colour camera……….…. 440,000 pixels

Lighting ……………………... 20 watts

Power………………………... 230 VAC, 50, 60 Hz

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

HP-HT TWO PHASE VIDEO SEPARATOR (VSE 700)

The apparatus is designed to separate the two phase fluids produced from the core at reservoir

conditions. It consists of a separation bore used to collect and separate produced fluids under

gravity and a measurement bore used to visualise the two phases fluid interface at reservoir

conditions. The measurement of produced fluids is performed with a video tracker designed to

monitor the position of the interface of the two fluids which is directly proportional of the

volumes of fluids produced from the core sample. The video tracker system comprises a high

resolution camera equipped with an integrated zoom, a back lighting installed in the rear side

and a motorized linear stage that is used to position the camera relative to the fluid interface to

be measured. The linear stage and the camera are both connected to the computer station so that

the image of the fluid can be displayed and recorded on the PC. The video software incorporates

facilities which enable to detect automatically the liquid/ liquid and gas/ liquid interface and so

derive the volumes of produced fluids from the core and so the changes in the core saturation.

FEATURES

Max pressure ………………… 10,000 psi

Max temperature……………… 150 °C

Max volume change………….. 100 ml, option: 300 ml

Volume accuracy…………...… 0.01 ml

Material………………………. Sapphire, Stainless steel, option: Titanium

Measurement resolution…….. 0.02 mm

Minimum field of view………. 10 mm

CDD colour camera……….…. 440,000 pixels

Lighting ……………………... 150 watts

Power………………………... 230 VAC, 50, 60 Hz

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

WET GAS METER (WG SERIES)

Designed to measure the volume of gas produced during a process at ambient conditions such as

gas-liquid relative permeability. The meter is complete with thermometer, spirit level, levelling

feet and gas connections. An option computer interface is available to acquire and display the

gas volume versus time.

FEATURES

Temperature Ambient

Pressure Atmospheric

Capacity 25 dm3 (i.e. 0.25 litres) per revolution

Scale 0.001 dm3

Maximum pressure 65 mbar

Flow range 30 to 90 litres per hour +/- 0.5%

Maximum capacity 99,999 litres

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

CAPILLARY SIGHT GLASS TUBE

The capillary sight glass tube provides a means to visually confirm miscibility of displaced

fluids during dynamic processes such as slim tube miscibility experiments and core

displacement test. The cell is made with a glass capillary tube embraced with two flanges at its

ends.

FEATURES

Max pressure 10,000 psi

Temperature up to 150°C

Wetted parts Stainless steel, sapphire

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

BACK PRESSURE REGULATOR (BPR)

Vinci offers back pressure regulators designed to regulate the pressure in fluid flow studies. The

BPR consists of two chambers separated by a piston with a needle connected to it on the lower

side. The upper chamber receives the gas dome pressure and the lower chamber the process

pressure. The BPR acts a comparator. When the dome pressure is higher than the process

pressure the needle seals off the pressure and maintains the pressure. Inversely when the process

pressure exceeds the dome pressure the needle opens up and the excess process fluid flows out.

That way, on continuous flow these 2 stages are looped continuously and the process pressure is

balanced to the dome controlled constant value.

FEATURES

Maximum pressure 10,000 psi

Flow rate 0.01 to 25 cc/min

Max Temperature 150°C

Wetted part material stainless steel

Port connection 1/8”

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

ELECTRICAL ISOLATOR (EI 700)

The EI 700 is designed to electrically isolate one side of a core holder from the other when

placed in a non-conductive fluid stream. It can be used for reservoir condition electrical

properties during a relative permeability or a capillary pressure displacement test.

FEATURES

Maximum pressure: 10,000 psi

Max Temperature: 150°C

Internal volume: less than 1 cc

Wetted part material: stainless steel, peek

Port connection: 1/8”

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

AUTOMATED CONFINING PRESSURE CONTROLLER

(ACP 700)

The ACP 700 is designed to generate and maintain automatically a constant confining pressure

requested during core studies. It can also be used to maintain a constant differential pressure

between the pore pressure and confining pressure. The system consists of a positive

displacement pump of 100 cc capacity and 10,000 psi pressure, an automatic dual valve, a fluid

reservoir and two pressure transducers for pore and confining pressure control.

FEATURES

Confining pressure up to 10,000 psi

Pore pressure up to 10,000 psi

Pump cylinder capacity 100 cc

Air requirement 100 psi

Tubing connector 1/8”

Power 220 VAC 1 Ph, 50 Hz


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

FLOATING PISTON ACCUMULATOR (FPA SERIES)

The floating piston accumulators are available in a range of different volume and pressure

rating. These can be constructed in different material such as 316 stainless steel, aluminium,

titanium or hastelloy. The fluid seals may either be the standard Viton / Nitrile „O‟ rings and

PTFE back up ring.

FEATURES

Pressure 5,000 psi, 10,000 psi or 15,000 psi

Temperature Ambient to 150°C (300 °F)

Cell volume 100 cc, 300 cc, 500 cc, 700cc, 1,000cc, 2,000 cc, 5000 cc

Material 316 stainless steel, aluminium, titanium or hastelloy

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

MIXER CYLINDER (MC SERIES)

The MC series are double end piston type cylinders designed to store and mix any kind of fluids

at pressure and temperature. The sample fluid is isolated from the secondary driving fluid with a

floating piston and a magnetic mixer is located in the mixing sample chamber for proper

agitation. The mixer is magnetically coupled to a drive system through the accumulator end cap

which incorporates a permanent magnet driven by a direct current motor with variable speed. A

mixer controller permits to stop, start and control the speed of the mixer. The cylinder can be

operated in either upright or inverted orientation. Both end caps are provided with an inlet/outlet

port for fluid introduction or fluid sampling.

FEATURES

Model Volume

ml

Pressure

psi

Temp.

°C

Weight

Kg

Length

mm

Diameter

mm

Material

(1)

Thread

connection

MC 500-10 500 10,000 150 21 700 120 Stainless steel ¼” FNPT

MC 1000-10 1,000 10,000 150 25 750 120 Stainless steel ¼” FNPT

MC 2000-10 2,000 10,000 150 35 900 150 Stainless steel ¼” FNPT

MC 500-15 500 15,000 200 21 700 120 Stainless steel 1/8” FLP

MC 1000-15 1,000 15,000 200 25 750 120 Stainless steel 1/8” FLP

MC 2000-15 2,000 15,000 200 35 900 150 Stainless steel 1/8” FLP (1) Titanium material available.

Mixer controller

Power requirement…………………… 230 VAC, 50 Hz, 100 W

BENEFITS

H2S resistant

The impeller provides a minimum dead volume

Provide rigorous agitation of entire fluid sample

Capable of mixing high viscosity samples up to 1,000 cp

High speed, allows equilibrium to be reached in minimum time

Reduces operating time for establishing phase equilibrium on sample.

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

FLUID TRANSFER VESSELS (FTV SERIES)

The fluid transfer vessels uses a glass tube embraced in two end plugs which are held in place

with two aluminium tie bars. The glass tube is protected by an external polycarbonate tube in

case of failure of the glass. The top end plug can be removed easily to load the fluid in the

vessel. The fluid is transferred from the vessel to another accumulator by applying air pressure

on the top port while the fluid passes through the bottom port of the vessel.

FEATURES

Pressure 150 psi

Volume 1,500 cc (other upon request)

Material Glass

Fluids brine, oil, mud, drilling fluid, etc

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

HYDRAULIC INTENSIFIER (HI SERIES)

The HI series are dual cavity cylinders equipped with a low pressure (LP) bore at one end and a

high pressure (HP) bore at the other end. The pistons in each cylinder bore are connected by a

solid rod. When pressurized fluid enters the larger bore, the fluid in the smaller bore is

compressed to a pressure multiplied by the ratio of areas on the two pistons. Consequently,

pressures up to 150Kpsi can be achieved by using a commercially available lower pressure (10

Kpsi) pump. Material of construction is either stainless steel or titanium.

FEATURES

Model Ratio HP end

LP end

Volume

ml

Pressure

psi

ID

mm

Stroke

mm

Pressure

psi

ID

mm

HI 2 2 :1 50 20,000 25.46 98.24 10,000 36

HI 4 4 :1 25 40,000 18.00 98.24 10,000 36

HI 6 6 :1 20 60,000 14.70 117.89 10,000 36

HI 8 8 :1 15 80,000 12.73 117.89 10,000 36

HI 10 10 :1 10 100,000 11.38 98.24 10,000 36

HI 15 15 :1 5 150,000 9.30 73.68 10,000 36

Additional features: Temperature ambient

Thread connection ¼” FNPT (Low pressure side ) and ¼” FHP (High pressure side)

Material Stainless steel or titanium

Weight Approx. 22 Kg

Length 600 mm

Diameter 90 mm to 120 mm depending on the model.

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

PRESSURE GENERATOR SYSTEM (PGS)

Designed to provide hydraulic pressure for Hg free fluid transfer at pressure condition.

Maximum output is 10,000 psi. The system comes complete with control valves, air driven

liquid pump, pressure gauge, air regulator, relief valve and frame.

FEATURES

Max outlet pressure 10,000 psi

Air inlet 30 to 145 psi (10 bar).

Wetted parts Stainless steel,

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

DIGITAL PRESSURE GAUGE (DPG SERIES)

The Digital Pressure Gauge series is designed for extremely accurate pressure measurement to

meet your most demanding requirements for precision laboratory or field measurement

instrumentation. The instrument includes a high precision analog pressure transducer, a

rupture disc for over pressure protection, a five digit digital display and a data logging

software for automatic data acquisition.

FEATURES

Model DPG series

Pressure range up to 10,000 psi (other range available)

Accuracy 0.1% FS

Port connection 1/8” autoclave type

Wetted part stainless steel

Power supply 220 VAC 1 Ph, 50 Hz

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

DEADWEIGHT GAUGE

Primary pressure standard designed for high pressure calibration applications. The device

consists of a vertically mounted precision lapped piston and cylinder assembly. Accurately

calibrated masses are loaded onto the piston, which rises freely within its cylinder. These

weights balance the upward force created by the application of pressure within the system.

Delivered with a carrying case.

FEATURES

Model Dual piston

Operation Oil operated

Pressure range 1 bar (15 psi) to 1,100 bar (16,000 psi)

Accuracy 0.015% RDG

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



PE

TR

OP

HY

SIC

S

UNINTERRUPTABLE POWER SUPPLY (UPS 16)

Back-up power protection used in most laboratories against electrical noise, sags, surges and

brownouts which affect the sensitivity of the electrical components of the laboratory equipment.

FEATURES

Output power capacity 12,800 Watts / 16,000 VA

Max configurable power 12,800 Watts / 16,000 VA

Input voltage 240 V +-1 %, single phase

Output voltage 240 V +-1 %, single phase

Efficiency at full load 90%

Back up time 6 minutes at full load (12,800 watts)

17 minutes at half load (6,400 Watts)

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76


http://www.vinci-technologies.com

100/10

0

PE

TR

OP

HY

SIC

S

OTHER COMPONENTS

Vacuum pump: Based on double stage rotary vane pump and featuring a max pumping speed

of 2.5 m3/h and a vacuum rate of 10

-3 mbar.

Air compressor: Designed to generate compressed air of 7 to 10 bar when compressed air is not

available.

Controlled temperature air bath: Designed to provide homogeneous temperature with

extreme accuracy. A large range of air bath is available depending on temperature ranges,

dimension and temperature homogeneity accuracy. The air bath can be provided with one or

two front and rear doors and with or without windows.

Thermostatic bath: Designed to provide heating and cooling source with an accurate

regulation.

Fraction collector: Inline effluent fraction collector for collecting up to 70 individual liquid

sample fractions automatically on a time or volume basis

PH meter: Inline pH probe and meter for monitoring effluent pH as a function of time.

catalogue of products 2011 vinci technologies · 2011. 3. 11. · vinci technologies parc de...

Documents