ccna brush up notes
DESCRIPTION
No need to browse through 1000 pages to revise your CCNA.This is a short book consisting of only 200 Pages with all the required material.TRANSCRIPT
-
CCNA Notes
Introduction
Cisco offers two options for obtaining the CCNA certification:
Pass Exam 640-802 OR Pass Exam 640-822 AND Exam 640-816
While you can use these notes to prepare for either exam, the notes are geared towards passing the single exam. I recommend you study all of the material and take the single exam option rather than taking two exams.
Cisco Device Icons
The following table lists the specific icons Cisco uses to represent network devices and connections.
Icon Represents
Hub
Bridge
Switch
Router
Access point
Network cloud
-
Ethernet connection
Serial Line connection
Wireless connection
Virtual Circuit
-
The OSI Model
As you study this section, answer the following questions:
What is the OSI model and why is it important in understanding networking? How does the third OSI model layer relate to administering routers? Which OSI model layer is concerned with MAC addresses? What protocols correspond to the Presentation and Session layers? What is the difference between the TCP and UDP protocols? What is the EIA/TIA 232 protocol concerned with?
This section covers the following exam objectives:
103. Use the OSI and TCP/IP models and their associated protocols to explain how data flows in a network
105. Describe the purpose and basic operation of the protocols in the OSI and TCP models 110. Identify and correct common network problems at layers 1, 2, 3 and 7 using a layered
model approach
OSI Model Facts
The OSI model classifies and organizes the tasks that hosts perform to prepare data for transport across the network. You should be familiar with the OSI model because it is the most widely used method for understanding and talking about network communications. However, remember that it is only a theoretical model that defines standards for programmers and network administrators, not a model of actual physical layers.
Using the OSI model to discuss networking concepts has the following advantages:
Provides a common language or reference point between network professionals Divides networking tasks into logical layers for easier comprehension Allows specialization of features at different levels Aids in troubleshooting Promotes standards interoperability between networks and devices Provides modularity in networking features (developers can change features without
changing the entire approach)
However, you must remember the following limitations of the OSI model.
OSI layers are theoretical and do not actually perform real functions. Industry implementations rarely have a layer-to-layer correspondence with the OSI layers. Different protocols within the stack perform different functions that help send or receive the
overall message. A particular protocol implementation may not represent every OSI layer (or may spread
across multiple layers).
To help remember the layer names of the OSI model, try the following mnemonic devices:
Layer NameMnemonic
(Bottom to top)Mnemonic
(Top to bottom)
Layer 7 Application Away All
Layer 6 Presentation Pizza People
Layer 5 Session Sausage Seem
-
Layer 4 Transport Throw To
Layer 3 Network Not Need
Layer 2 Data Link Do Data
Layer 1 Physical Please Processing
Have some fun and come up with your own mnemonic for the OSI model, but stick to just one so you don't get confused.
Lower OSI Layer Facts
The following table summarizes basic characteristics of the lower OSI model layers.
Layer Description
Physical
The Physical layer of the OSI model sets standards for sending and receiving electrical signals between devices. It describes how digital data (bits) are converted to electric pulses, radio waves, or pulses of lights.
Devices that operate at the physical layer send and receive a stream of bits.
Data Link
Media Access Control (MAC)
The Media Access Control (MAC) layer defines specifications for controlling access to the media. The MAC sublayer is responsible for:
Adding frame start and stop information to the packet Adding Cyclical Redundancy Check (CRC) for error checking Converting frames into bits to be sent across the network Identifying network devices and network topologies in preparation for
media transmission Defining an address (such as the MAC address) for each physical device
on the network Controlling access to the transmission medium
Logical Link Control (LLC)
The Logical Link Control (LLC) layer provides an interface between the MAC layer and upper-layer protocols. LLC protocols are defined by the IEEE 802.2 committee. The LLC sublayer is responsible for:
Maintaining orderly delivery of frames through sequencing Controlling the flow or rate of transmissions using the following:
o Acknowledgementso Bufferingo Windowing
Ensuring error-free reception of messages by retransmitting Converting data into an acceptable form for the upper layers Removing framing information from the packet and forwarding the
message to the Network layer Provide a way for upper layers of the OSI model to use any MAC layer
protocol Defining Service Access Points (SAPs) by tracking and managing
different protocols
Network
The Network layer describes how data is routed across networks and on to the destination. Network layer functions include:
Maintaining addresses of neighboring routers. Maintaining a list of known networks.
-
Determining the next network point to which data should be sent. Routers use a routing protocol to take into account various factors such as the number of hops in the path, link speed, and link reliability to select the optimal path for data.
Packets forwarded from the Transport to the Network layer become datagrams and network-specific (routing) information is added. Network layer protocols then ensure that the data arrives at the intended destinations.
Transport
The Transport layer provides a transition between the upper and lower layers of the OSI model, making the upper and lower layers transparent from each other.
Upper layers format and process data without regard for delivery Lower layers prepare the data for delivery by fragmenting and attaching
transport required information
Transport layer uses the following:
Port (or socket) numbers are used to identify distinct applications running on the same system. This allows each host to provide multiple services.
The Transport layer receives large packets of information from higher layers and breaks them into smaller packets called segments. Segmentation is necessary to enable the data to meet network size and format restrictions.
The receiving Transport layer uses packet sequence numbers to reassemble segments into the original message.
Connection-oriented protocols perform error detection and correction and identify lost packets for retransmission. A connection-oriented protocol is a good choice where:
o Reliable, error-free communications are more important than speed
o Larger chunks of data are being sent Connectionless services assume an existing link between devices and
allow transmission without extensive session establishment. Connectionless communications use no error checking, session establishment, or acknowledgements. Connectionless protocols allow quick, efficient communication at the risk of data errors and packet loss. Connectionless protocols are a good choice where:
o Speed is important o Smaller chunks of data are being sent
Upper OSI Model Layer Facts
The following table summarizes basic characteristics of the upper OSI model layers.
Layer Description
Application
The Application layer integrates network functionality into the host operating system, and enables network services. The Application layer does not include specific applications that provide services, but rather provides the capability for services to operate on the network. These services include:
File services--transferring, storing, and updating shared data Print services--enabling network printers to be shared by multiple users Message services--transferring data in many formats (text, audio, video) from
one location to another, or from one user to another
-
Application services--sharing application processing throughout the network and enabling specialized network servers to perform processing tasks
Database services--storing, retrieving, and coordinating database information throughout the network
The Application layer specifies many important network services that are used on the Internet. These include:
HTTP Telnet FTP TFTP SNMP
Note: Most Application layer protocols operate at multiple layers down to the Session and even Transport layers. However, they are classified as Application layer protocols because they start at the Application layer (the Application layer is the highest layer where they operate).
Presentation
The Presentation layer formats or "presents" data into a compatible form for receipt by the Application layer or the destination system. Specifically, the Presentation layer ensures:
Formatting and translation of data between systems Negotiation of data transfer syntax between systems, through converting
character sets to the correct format. Compatibility with the host Encapsulation of data into message envelopes by encryption and compression Restoration of data by decryption and decompression
The Presentation layer formats data for the Application layer. Therefore, it also sets standards for multimedia and other file formats. These include standard file formats such as:
JPEG, BMP, TIFF, PICT MPEG, WMV, AVI ASCII, EBCDIC MIDI, WAV
Session
The Session layer's primary function is managing the sessions in which data is transferred. Functions at this layer may include:
Establishment and maintenance of communication sessions between the network hosts, ensuring that data is transported.
Management of multiple sessions (each client connection is called a session). A server can concurrently maintain thousands of sessions.
Assignment of the session ID number to each session, which is then used by the Transport layer to properly route the messages.
Dialog control--specifying how the network devices coordinate with each other (simplex, half-duplex, and full-duplex).
Termination of communication sessions between network hosts upon completion of the data transfer.
The Session layer protocols and interfaces coordinate requests and responses between different hosts using the same application. These protocols and interfaces include:
-
Network File System (NFS) Apple Session Protocol (ASP) Structured Query Language (SQL) Remote procedure call (RPC) X Window
OSI Layer Review
The following table compares the functions performed at each OSI model layer.
Layer Description and Keywords Protocols DevicesEncapsulation
Application
Provides an interface for a service to operate
Communication partner identification
HTTP Telnet FTP TFTP SNMP
User information and data
Presentation
Data format (file formats) Encryption, translation, and
compression Data format and exchange
JPEG, BMP, TIFF, PICT
MPEG, WMV, AVI
ASCII, EBCDIC
MIDI, WAV
Data
Session
Keeps data streams separate (session identification)
Set up, maintain, and tear down communication sessions
SQL NFS ASP RPC X
window
Data
Transport
Reliable (connection-oriented) and unreliable (connectionless) communications
End-to-end flow control Port and socket numbers Segmentation, sequencing,
and combination
TCP (connection-oriented)
UDP (connectionless)
Segments
Network
Logical addresses Path determination
(identification and selection) Routing packets
IP IPX AppleTal
k DECNET
Routers Layer 3
switches Packets
-
Data Link
Logical Link Control (LLC)
Convert bits into bytes and bytes into frames
MAC address, hardware address
Logical network topology Media access Flow control
o Acknowledgements o Buffering o Windowing
Parity and CRC
LAN protocols: 802.2 (LLC), 802.3 (Ethernet), 802.5 (Token Ring), 802.11 (Wireless)
WAN protocols: HDLC, PPP, Frame Relay, ISDN, ATM
Network Interface Card (NIC) transceivers
Switch Bridge
FramesMedia Access Control (MAC)
Physical
Move bits across media Cables, connectors, pin
positions Electrical signals (voltage,
bit synchronization) Physical topology (network
layout)
EIA/TIA 232 (serial signaling)
V.35 (modem signaling)
Cat5 RJ45
Transmission media (cable and wires)
Media connectors
Transceivers (including transceivers built into NICs)
Modems Repeaters Hubs Multiplexer
s CSUs/DSU
s Wireless
Access Points
Bits
-
TCP/IP
As you study this section, answer the following questions:
How does the DOD model correspond to the OSI model? Which TCP/IP protocols allow for copying and moving files? What does the Telnet protocol allow you to do? Which protocol includes a set of messages that controls how data moves through a network? What is the role of the subnet mask? What is the default address class of the IP address 132.11.166.5? What three address ranges are used for private IP addresses? What is the broadcast address of network 132.11.0.0?
This section covers the following exam objectives:
103. Use the OSI and TCP/IP models and their associated protocols to explain how data flows in a network
104. Describe common networked applications including web applications 105. Describe the purpose and basic operation of the protocols in the OSI and TCP models 106. Describe the impact of applications (Voice Over IP and Video Over IP) on a network 301. Describe the operation and benefits of using private and public IP addressing
TCP/IP Protocol Suite Facts
Groups of protocols (called protocol suites or protocol stacks) are designed to interact and be used together. The TCP/IP protocol suite is used on the Internet and on most networks. Nearly all computers today use TCP/IP protocols for communication because it is highly scalable and routable. When learning about TCP/IP protocols, it is common to use a theoretical layered model called the TCP/IP model (also known as the Department of Defense (DoD) model). The layers of the DoD model are as follows:
The Application layer (also called the Process layer) corresponds to the Session, Presentation, and Application layers of the OSI model.
The Host-to-host layer is comparable to the Transport layer of the OSI model and is responsible for error checking and reliable packet delivery. Here, the data stream is broken into segments that must be assigned sequence numbers so that the segments can be reassembled correctly on the remote side after they are transported.
The Internet layer is comparable to the Network layer of the OSI model. It is responsible for moving packets through a network. This involves addressing of hosts and making routing decisions to identify how the packet transverses the network.
The Network Access layer corresponds to the functions of the Physical and Data Link layers of the OSI model. It is responsible for describing the physical layout of the network and how messages are formatted on the transmission medium. Sometimes this layer is divided into the Network Access and the Physical layer.
Note: The TCP/IP model focuses specifically on the functions in the Internet layer and the Host-to-Host layer. All other functions of the traditional OSI model are encompassed in the first and fourth layers.
The following table lists several protocols in the TCP/IP protocol suite.
Protocol DescriptionOSI Model Layer(s)
DoD Model Layer
File Transfer Protocol (FTP)
File Transfer Protocol (FTP) provides a generic method of transferring files. It
Application, Presentation,
Application/Process
-
can include file security through usernames and passwords, and it allows file transfer between dissimilar computer systems.
Session
Trivial File Transfer Protocol (TFTP)
Trivial File Transfer Protocol (TFTP) is similar to FTP. It lets you transfer files between a host and an FTP server. However, it provides no user authentication and uses UDP instead of TCP as the transport protocol.
Application, Presentation, Session
Application/Process
Hypertext Transfer Protocol (HTTP)
The Hypertext Transfer Protocol (HTTP) is used by Web browsers and Web servers to exchange files (such as Web pages) through the World Wide Web and intranets. HTTP can be described as an information requesting and responding protocol. It is typically used to request and send Web documents, but is also used as the protocol for communication between agents using different TCP/IP protocols.
Application, Presentation, Session
Application/Process
Simple Mail Transfer Protocol (SMTP)
Simple Mail Transfer Protocol (SMTP) is used to route electronic mail through the internetwork. E-mail applications provide the interface to communicate with SMTP or mail servers.
Application, Presentation, Session
Application/Process
Simple Network Management Protocol (SNMP)
Simple Network Management Protocol (SNMP) is a protocol designed for managing complex networks. SNMP lets network hosts exchange configuration and status information. This information can be gathered by management software and used to monitor and manage the network.
Application, Presentation, Session
Application/Process
Telnet
Remote Terminal Emulation (Telnet) allows an attached computer to act as a dumb terminal, with data processing taking place on the TCP/IP host computer. It is still widely used to provide connectivity between dissimilar systems.
Application, Presentation, Session
Application/Process
Network File System (NFS)
Network File System (NFS) was initially developed by Sun Microsystems. It consists of several protocols that enable users on various platforms to seamlessly access files from remote file systems.
Application, Presentation, Session
Application/Process
Voice Over Internet Protocol (VoIP)
Voice over Internet Protocol (VoIP) is a protocol optimized for the transmission of voice through the Internet or other packet switched networks. Voice over IP protocols carry telephony signals as digital audio encapsulated in a data packet stream over IP.
Application, Presentation, Session
Application/Process
-
Transmission Control Protocol (TCP)
Transmission Control Protocol (TCP) operates at the Transport layer. It provides connection-oriented services and performs segment sequencing and service addressing. It also performs important error-checking functions and is considered a host-to-host protocol.
Transport Host-to-Host (Transport)
User Datagram Protocol (UDP)
User Datagram Protocol (UDP) is considered a host-to-host protocol like TCP. It also performs functions at the Transport layer. However, it is not connection-oriented like TCP. Because of less overhead, it transfers data faster, but is not as reliable.
Transport Host-to-Host (Transport)
Domain Name System (DNS)
Domain Name System (DNS) is a system that is distributed throughout the internetwork to provide address/name resolution. For example, the name "www.testout.com" would be identified with a specific IP address.
Transport Host-to-Host (Transport)
Internet Protocol (IP)
Internet Protocol (IP) is the main TCP/IP protocol. It is a connectionless protocol that makes routing path decisions, based on the information it receives from ARP. It also handles logical addressing issues through the use of IP addresses.
Network Internet
Internet Control Message Protocol (ICMP)
Internet Control Message Protocol (ICMP) works closely with IP in providing error and control information that helps move data packets through the internetwork.
Network Internet
Internet Group Membership Protocol (IGMP)
Internet Group Membership Protocol (IGMP) is a protocol for defining host groups. All group members can receive broadcast messages intended for the group (called multicasts). Multicast groups can be composed of devices within the same network or across networks (connected with a router).
Network Internet
Address Resolution Protocol (ARP)
Address Resolution Protocol (ARP) is used to get the MAC address of a host from a known IP address. ARP is used within a subnet to get the MAC address of a device on the same subnet as the requesting device.
Network Internet
Reverse Address Resolution Protocol (RARP)
Both BOOTP (Bootstrap Protocol) and RARP (Reverse Address Resolution Protocol) are used to discover the IP address of a device with a known MAC address. BOOTP is an enhancement to RARP, and is more commonly implemented than RARP. As its name implies, BOOTP is used by computers as they boot to receive an IP address from a
Network Internet
Bootstrap Protocol (BOOTP)
Network Internet
-
BOOTP server. The BOOTP address request packet sent by the host is answered by the server.
Dynamic Host Configuration Protocol (DHCP)
The Dynamic Host Configuration Protocol (DHCP) simplifies address administration. DHCP servers maintain a list of available and assigned addresses, and communicate configuration information to requesting hosts. DHCP has the following two components.
A protocol for delivering IP configuration parameters from a DHCP server to a host
A protocol specifying how IP addresses are assigned
Network Internet
Open Shortest Path First (OSPF)
Open Shortest Path First (OSPF) is a route discovery protocol that uses the link-state method. It is more efficient than RIP in updating routing tables, especially on large networks.
Network Internet
Routing Information Protocol (RIP)
Routing Information Protocol (RIP) is a route discovery protocol that uses the distance-vector method. If the network is large and complex, OSPF should be used instead of RIP.
Network Internet
The TCP/IP protocol suite was developed to work independently of the Physical layer implementation. You can use a wide variety of architectures with the TCP/IP protocol suite.
IP Address and Class Facts
IP addresses allow hosts to participate on IP based networks. An IP address:
Is a 32-bit binary number represented as four octets (four 8-bit values). Each octet is separated by a period.
IP addresses can be represented in one of two ways: o Decimal (for example 131.107.2.200). In decimal notation, each octet must be
between 0 and 255. o Binary (for example 10000011.01101011.00000010.11001000). In binary notation,
each octet is an 8-digit number. The IP address includes both the network and the host address. Each IP address has an implied address class that can be used to infer the network portion of
the address. The subnet mask is a 32-bit number that is associated with each IP address that identifies
the network portion of the address. In binary form, the subnet mask is always a series of 1's followed by a series of 0's (1's and 0's are never mixed in sequence in the mask). A simple mask might be 255.255.255.0.
IP addresses have a default class. The address class identifies the range of IP addresses and a default subnet mask used for the range. The following table shows the default address class for each IP address range.
-
Class Address Range First Octet Range Default Subnet Mask
A 1.0.0.0 to 126.255.255.2551-126
(00000001--01111110 binary)255.0.0.0
B 128.0.0.0 to 191.255.255.255128-191
(10000000--10111111 binary)255.255.0.0
C 192.0.0.0 to 223.255.255.255192-223
(11000000--11011111 binary)255.255.255.0
D 224.0.0.0 to 239.255.255.255224-239
(11100000--11101111 binary)n/a
E 240.0.0.0 to 255.255.255.255240-255
(11110000--11111111 binary)n/a
When using the default subnet mask for an IP address, you have the following number of subnet addresses and hosts per subnet:
There are only 126 Class A network IDs (most of these addresses are already assigned). Each class A address gives you 16,777,214 hosts per network.
There are 16,384 Class B network IDs. Each class B address gives you 65,534 hosts per network.
There are 2,097,152 Class C network IDs. Each class C address gives you 254 hosts per network.
Class D addresses are used for multicast groups rather than network and host IDs. Class E addresses are reserved for experimental use.
Special Address Facts
You should understand the following special addresses:
Address Consideration
Network
The first octet(s) in an address range is used to identify the network itself. For the network address, the host portion of the address contains all 0's. For example:
Class A network address: 115.0.0.0 Class B network address: 154.90.0.0 Class C network address: 221.65.244.0
0.0.0.0 is the network address used by routers to specify the "default" route. Using a generic value reduces the number of routing table entries. Some older routers use this address as a broadcast address.
Host
The range of IP addresses available to be assigned to network hosts is identified by the subnet mask and/or the address class. For example:
For the class A network address 115.0.0.0, the host range is 115.0.0.1 to 115.255.255.254.
For the class B network address 154.90.0.0, the host range is 154.90.0.1 to 154.90.255.254.
For the class C network address 221.65.244.0, the host range is 221.65.244.1 to 221.65.244.254.
Note: A special way to identify a host on a network is by setting the network portion of the address to all 0's. For example, the address 0.0.64.128 means "host 64.128 on this network."
Broadcast The last address in the range is used as the broadcast address and is used to send
-
messages to all hosts on the network. In binary form, the broadcast address has all 1's in the host portion of the address. For example, assuming the default subnet masks are used:
115.255.255.255 is the broadcast address for network 115.0.0.0 154.90.255.255 is the broadcast address for network 154.90.0.0 221.65.244.255 is the broadcast address for network 221.65.244.0
Two other formats you might see for the broadcast address:
The broadcast address might also be designated by setting each of the network address bits to 0. For example, 0.0.255.255 is the broadcast address of a Class B address. This designation means "the broadcast address for this network."
255.255.255.255 indicates a broadcast message intended for all hosts on this network.
Local host
Addresses in the 127.0.0.0 range are reserved for the local host (in other words "this" host or the host you're currently working at). The most commonly-used address is 127.0.0.1 which is the loopback address.
Private use
The following address ranges have been reserved for private use:
10.0.0.0 to 10.255.255.255 172.16.0.0 to 172.31.255.255 192.168.0.0 to 192.168.255.255
Use addresses in these ranges for your private networks. Routers connected to the Internet typically filter messages within these ranges and prevent them from being propagated to the Internet.
-
Device Communication
As you study this section, answer the following questions:
Which OSI model layer uses service data units called frames? When moving from top to bottom through the OSI model layers, which comes first, packets
or segments? What gets added to the service data unit at the Network layer? At the Data Link layer?
This section covers the following exam objectives:
103. Use the OSI and TCP/IP models and their associated protocols to explain how data flows in a network
Data Encapsulation Facts
Encapsulation is the process of breaking a message into packets, adding control and other information, and transmitting the message through the transmission media. You need to know the following five-step data encapsulation process:
1. Upper layers prepare the data to be sent through the network. 2. The Transport layer breaks the data into pieces called segments, adding sequencing and
control information. 3. The Network layer converts the segments into packets, adding logical network and device
addresses. 4. The Data Link layer converts the packets into frames, adding physical device addressing
information. 5. The Physical layer converts the frames into bits for transmission across the transmission
media.
The following short descriptions can help you remember the steps of the data encapsulation process:
1. Upper layers--data2. Transport layer--segments3. Network layer--packets containing logical addresses 4. Data Link layer--framing that adds physical addresses 5. Physical layer--bits
-
Ethernet
As you study this section, answer the following questions:
What is the purpose of the jam signal and the back off in Ethernet communications? What is the maximum cable length allowed for 100BaseTX? What is the physical device address used on Ethernet networks? Two devices are using full-duplex communications with the 1000BaseT standards. What is
the amount of bandwidth available? Under what conditions can you disable collision detection on an Ethernet network?
This section covers the following exam objectives:
109. Describe the components required for network and Internet communications 201. Select the appropriate media, cables, ports, and connectors to connect switches to other
network devices and hosts 202. Explain the technology and media access control method for Ethernet networks 403. Select the appropriate media, cables, ports, and connectors to connect routers to other
network devices and hosts
Ethernet Architecture Facts
The following table shows specifics of the Ethernet architecture.
Specification Description
Topology
The physical topology is the mapping of the nodes of a network and the physical connections between them, such as the layout of wiring, cables, the locations of nodes, and the interconnections between the nodes and the cabling or wiring system. The logical topology is the way messages are sent through the network connections. Ethernet supports the following topologies: Physical bus, logical busPhysical star, logical busPhysical star, logical star
Media access
Ethernet uses Carrier Sense, Multiple Access/Collision Detection (CSMA/CD) to control access to the transmission medium. Devices use the following process to send data:
1. Because all devices have equal access to the transmission media (multiple access), a device with data to send first listens to the transmission medium to determine if it is free (carrier sense).
2. If it is not free, the device waits a random time and listens again to the transmission medium. When it is free, the device transmits its message.
3. If two devices transmit at the same time, a collision occurs. The sending devices detect the collision (collision detection) and send a jam signal.
4. Both devices wait a random length of time before attempting to resend the original message (called a backoff).
Transmission media
Ethernet supports the following cable types:
Unshielded twisted-pair cables (UTP) with RJ-45 connectors. This is the most common transmission medium used for Ethernet. Each cable consists of eight wires, twisted into four pairs. UTP cables are classified by categories:
o Cat3, rated up to 10 Mbps o Cat4, rated up to 16 Mbps
-
o Cat5, rated up to 100 Mbps o Cat5e, rated up to 1,000 Mbps (gigabit)
Fiber optic, most commonly used in high-speed applications such as servers or streaming media. Fiber optic cables have ST, SC, LC, and MT-RJ connectors.
Coaxial for older Ethernet implementations (often called thinnet or thicknet networks). Coaxial cables have F-Type and BNC connectors.
Frame type
The Ethernet frame size is 64 to 1518 bytes (this is the same for all Ethernet standards). Four frame types are supported:
Ethernet 802.3 is the original Ethernet frame type. Ethernet 802.2 is the frame type that accommodates standards set by the
IEEE 802.2 committee related to the logical link control (LLC) sublayer. It is a more current frame type than 802.3.
Ethernet II is a frame type that provides the ability to use TCP/IP as a transport/network layer protocol. Other Ethernet frame types operate strictly with IPX/SPX as a transport/network layer protocol.
Ethernet SNAP (SubNetwork Address Protocol) is an enhanced version of Ethernet 802.2 that allows for greater compatibility with other network architectures such as Token Ring. This frame type also supports TCP/IP.
Physical address
The MAC address (also called the burned-in address) is the Data Link layer physical device address.
The MAC address is a 12-digit hexadecimal number (each number ranges from 0-9 or A-F).
The address is often written as 00-B0-D0-06-BC-AC or 00B0.D006.BCAC, although dashes, periods, and colons can be used to divide the MAC address parts.
The MAC address is guaranteed unique through design. The first half (first 6 digits) of the MAC address is assigned to each manufacturer. The manufacturer determines the rest of the address, assigning a unique value which identifies the host address. A manufacturer that uses all the addresses in the original assignment can apply for a new MAC address assignment.
Note: Some network cards allow you to change (logically assigned address) the MAC address through jumpers, switches, or software. However, there is little practical reason for doing so.
Ethernet Standards
The following table compares the characteristics of various Ethernet implementations.
Category Standard Bandwidth Cable TypeMaximum Segment Length
Ethernet
10Base5 10 MbpsCoaxial (thicknet)
500 meters
10Base2 10 Mbps Coaxial (thinnet) 185 meters
10BaseT
10 Mbps (half duplex)20 Mbps (full duplex)
Twisted pair (Cat3, 4, or 5)
100 meters
-
Fast Ethernet
100BaseTX
100 Mbps (half duplex)200 Mbps (full duplex)
Twisted pair (Cat5)
100 meters
100BaseT4
100 Mbps (half duplex)200 Mbps (full duplex)
Twisted pair (Cat5)
100 meters
100BaseFX
100 Mbps (half duplex)200 Mbps (full duplex)
Fiber optic
412 meters (half duplex multimode cable)2,000 meters (full duplex singlemode cable)
Gigabit Ethernet
1000BaseSX (short)
1,000 Mbps (half duplex)2,000 Mbps (full duplex)
Fiber optic220 to 550 meters depending on cable quality
1000BaseLX (long)
1,000 Mbps (half duplex)2,000 Mbps (full duplex)
Fiber optic550 to 5,000 meters depending on cable quality
1000BaseCX (short copper)
1,000 Mbps (half duplex)2,000 Mbps (full duplex)
Special copper25 meters, used within wiring closets
1000BaseT
1,000 Mbps (half duplex)2,000 Mbps (full duplex)
Twisted pair (Cat5e)
100 meters
Fast Ethernet was designed to be as compatible with 10BaseT Ethernet as possible. This provides an easy migration path from 10BaseT to 100BaseT/100BaseT4 (and even to Gigabit Ethernet).
Most new networking devices that are Fast or Gigabit Ethernet capable also support 10BaseT standards. Devices autosense the specifics of the network configuration and set themselves to use the fastest communication method possible.
If your network uses 10BaseT and has Cat5 cable, you can slowly migrate from 10BaseT to FastEthernet (remember that FastEthernet uses Cat5 cable). As you replace components such as NICs and hubs with FastEthernet devices, portions of the network will begin operating at FastEthernet speeds.
You can begin your upgrade with: o Critical components, such as hubs, switches, and server NICs o Segments that service mission-critical applications o Workstations that have heavy bandwidth requirements
Half- and Full-Duplex
With the original Ethernet standards, all devices shared the same cable. This caused two problems:
Collisions occur when two devices transmit at the same time. Devices needed to be able to detect and recover from collisions.
Each device could either transmit or receive data at any given time. This meant that the device was either receiving data or listening for incoming data. Devices were not able to both send and receive at the same time (much like using a one-lane road for traffic in two different directions).
-
These two problems were solved in the following ways:
Using twisted pair cable, multiple strands of wires are combined into a single cable. Devices can use different wires to send and receive data (allowing them to do both simultaneously).
Using switches, devices are given a dedicated communication path. With a single device connected to a switch port, collisions are eliminated.
With these problems solved, you can turn off collision detection. Devices can transmit and receive data simultaneously, and can begin transmitting data as soon as they have data to send.
Devices with collision detection turned on operate in half-duplex mode; devices with collision detection turned off operate in full-duplex mode.
Mode Description Bandwidth
Half-duplex
Collision detection is turned on The device can only send or receive at
any given time Devices connected to a hub must use
half-duplex communication
Up to the rated bandwidth (10 Mbps for 10BaseT, 100 Mbps for 100BaseT, etc.)
Full-duplex
Collision detection is turned off The device can send and receive at the
same time Requires full-duplex capable NICs Requires switches with dedicated
switch ports (a single device per port)
Double the rated bandwidth (20 Mbps for 10BaseT, 200 Mbps for 100BaseT, etc.)
-
Bridging and Switching
As you study this section, answer the following questions:
What is the difference between a bridge and a switch? What is the 80/20 rule of network segmentation with bridges? How do bridges and switches learn MAC addresses? What is the difference between the store-and-forward and the fragment-free switching
methods? Which switching method is the fastest?
This section covers the following exam objectives:
101. Describe the purpose and functions of various network devices 102. Select the components required to meet a network specification 103. Use the OSI and TCP/IP models and their associated protocols to explain how data
flows in a network 108. Determine the path between two hosts across a network 109. Describe the components required for network and Internet communications 204. Explain basic switching concepts and the operation of Cisco switches
Bridge Facts
A bridge is a data forwarding device that provides data transfer. You should understand the following concepts relating to the operation of bridges.
Bridges connect two media segments that use the same protocol. Bridges examine the source address to determine the media segment of network devices. Bridges operate at the Data Link layer of the OSI model. Bridges maintain a table of device addresses and their corresponding segments. Each segment connected by a bridge can have the same network address. Messages within a media segment are prevented from crossing over to another segment.
Bridges offer the following advantages:
Bridges prevent wasted bandwidth by eliminating unnecessary traffic between segments. Bridges increase the maximum network length. Bridges forward packets for multiple upper-layer protocols. Bridges can link segments with dissimilar transmission media and media access methods.
Bridges have the following limitations:
Bridges cannot link multiple architectures because different frame types are used. Bridges cannot translate upper-layer protocols. Bridges cannot forward packets to different networks based on the network address. Bridges do not filter broadcast packets.
Use bridges to isolate traffic to a segment, or to prevent unwanted traffic from crossing over to other segments, or to slow WAN links. When designing the placement of bridges on the network, follow the 80/20 rule.
At least 80% of network traffic should stay within a segment. No more than 20% of network traffic should pass through the bridge to another segment.
Switch Facts
-
A switch is a multiport bridge. It provides the same functionality, but with a higher port density. In addition, switches provide features that cannot be found in bridges.
Switches are associated with the Data Link layer of the OSI Model. Switches build a forwarding database in a manner similar to bridges. Switches examine the
source and destination Data Link address in each packet to build the database and make forwarding decisions.
Switches connect multiple segments or devices and forward packets to only one specific port.
You can connect a single device to a switch port or multiple devices to a switch port by using a hub.
Switches offer the following advantages over a non-switched network.
Switches create separate collision domains. Switches provide guaranteed bandwidth between devices, if dedicated ports are used. Switches can be used to provide collision-free networking, if only one device is connected
to each switch port. Switches enable full-duplex communication. Switches induce less latency than other segmentation solutions. Switches can simultaneously switch multiple messages. Switches can mix 10 Mbps- and 100 Mbps-capable devices, if the switch is a 100 Mbps
switch. Ethernet switches can be implemented without re-cabling.
Switches have replaced bridges in most network applications.
Bridge and Switch Forwarding Facts
Both bridges and switches build a forwarding database. The database is a list of Data Link (MAC) addresses and the port used to reach the device. Bridges and switches can automatically learn about devices to build the forwarding database. A network administrator can also program the device database manually. Bridges and switches use the following process to dynamically build the forwarding database:
The process begins by examining the source address of an incoming packet. If the source address is not in the forwarding database, an entry for the address is made in the database. The port it came in on is also recorded.
The destination address is then examined. o If the destination address is in the database, the packet is forwarded to the
appropriate port if the port is different than the one on which it was received. o If the destination address is not in the database, the packet is sent out all ports except
for the one on which it was received. This is known as flooding. o A broadcast packet is forwarded (flooded) to all ports except the one on which it was
received.
Transparent bridges forward packets only if the following conditions are met.
The frame contains data from the layers above the Data Link layer. The frame's integrity has been verified through a valid Cyclic Redundancy Check (CRC). The frame is not addressed to the bridge.
How switches forward packets depends on the switch type. The following table compares the different methods the switch uses to forward packets (some Cisco switches support all three methods).
-
Method Characteristics
Store-and-forward
Store-and-forward switches:
Receive the entire frame. Verify the frame's integrity (check the CRC). Frames with errors are not
forwarded. Forward the frame to the destination device. Introduce more latency (delay) than cut-through switches.
Cut-through
Cut-through switches:
Read the destination device address. Forward the packet without verifying frame integrity. Are faster than store-and-forward switches (less latency).
Fragment-free
Fragment-free switches:
Read the first 64 bytes of a frame. Verify that the packet is not a fragment. Forward non-fragmented frames. Introduce some latency, but not as great as store-and-forward switching.
Note: Newer switches can monitor each port and determine which switching method to use. They can automatically change to store-and-forward if the number of errors on a port exceeds a configurable threshold.
-
Routing
As you study this section, answer the following questions:
What type of information is stored in the routing table? What is convergence? What is the function of a routing protocol? A computer needs to send a message to another computer on the same network. What MAC
address would go into the destination portion of the frame? A computer needs to send a message to another computer on a different network. What
MAC address would go into the destination portion of the frame? As a packet moves from device to device through an internetwork, do the Network layer
addresses change or remain the same?
This section covers the following exam objectives:
101. Describe the purpose and functions of various network devices 103. Use the OSI and TCP/IP models and their associated protocols to explain how data
flows in a network 108. Determine the path between two hosts across a network 109. Describe the components required for network and Internet communications 401. Describe basic routing concepts (including: packet forwarding, router lookup process)
Routing Facts
A router is a device that sends packets from one network to another network. Routers receive packets, read their headers to find addressing information, and send them on to their correct destination on the network or Internet. Routers can forward packets through an internetwork by maintaining routing information in a database called a routing table. The routing table typically contains the address of all known networks and routing information about that network such as:
Interface Routing Path Next Hop Route Metric (Cost) Route Timeout
Routers build and maintain their routing database by periodically sharing information with other routers. The exact format of these exchanges is based on the routing protocol. The routing protocol determines:
The information contained in the routing table How messages are routed from one network to another How topology changes (i.e. updates to the routing table) are communicated between routers
Regardless of the method used, changes in routing information take some time to be propagated to all routers on the network. The term convergence is used to describe the condition when all routers have the same (or correct) routing information.
Message Routing Facts
To send a message from one host to another on a different network, the following process is used:
1. The sending host prepares a packet to be sent. It uses its own IP address for the source Network layer address, and the IP address of the final receiving device as the destination Network layer address.
-
2. The sending host creates a frame by adding its own MAC address as the source Physical layer address. For the destination Physical layer address, it uses the MAC address of the default gateway router.
3. The sending host transmits the frame. 4. The next hop router reads the destination MAC address in the frame. Because the frame is
addressed to that router, it processes the frame. 5. The router strips off the frame header and examines the packet destination address. It uses a
routing protocol to identify the next hop router in the path. 6. The router repackages the packet into a new frame. It uses its own MAC address as the
source Physical layer address. It uses the MAC address of the next hop router for the destination Physical layer address.
7. The router transmits the frame. 8. The next hop router repeats steps 4 through 7 as necessary, until the frame arrives at the last
router in the path. 9. The last router in the path receives the frame and checks the destination IP address
contained in the packet. 10. Because the destination device is on a directly connected network, the router creates a frame
using its own MAC address as the source address, and the MAC address of the destination device as the destination physical address.
11. The router transmits the frame. 12. The destination device receives the frame. Inside the packet it finds the destination address
matching its own IP address, with the source IP address being that of the original sending device.
Be aware of the following:
On an Ethernet network, the Data Link layer address is the MAC address. On an IP network, the Network layer address is the IP address.
Both Data Link physical addresses and Network logical addresses are used to send packets between hosts.
The Data Link address identifies the physical interface. The Network address contains both a logical network address and a logical device address.
IP (Network layer) addresses are contained in the IP header; MAC (Data Link) addresses are contained in the Ethernet frame header.
Both the source and destination Network and Data Link addresses are typically contained in the packet.
Data Link addresses in the packet change as the packet is delivered from hop to hop. At any point in the process, the Data Link destination address indicates the physical address of the next hop on the route. The Data Link source address is the physical address of the device sending the frame.
Network addresses remain constant as the packet is delivered from hop to hop. The Network addresses indicate the logical address of the original sending device and the address of the final destination device.
A router uses the logical network address specified at the Network layer to forward messages to the appropriate network segment.
-
Connecting Cisco Devices
As you study this section, answer the following questions:
What HyperTerminal settings should you use to connect to the router console for the first time?
What are the requirements for using a VTY (virtual terminal) connection to a Cisco device? What type of cable do you use to connect a PC to a router console port?
After finishing this section, you should be able to complete the following tasks:
Use HyperTerminal to connect to a Cisco device console. Use Telnet to create a virtual terminal connection to a Cisco device.
This section covers the following exam objectives:
205. Perform and verify initial switch configuration tasks including remote access management
405. Access and utilize the router to set basic parameters
Device Connection Facts
Cisco routers and switches do not have monitors, and you cannot connect a keyboard or a mouse directly to the device. To manage the device, you connect to the router or switch through either a dedicated terminal or a PC. There are several options you can use to manage a Cisco device. These include:
Connection Type
Description
Console
A console connection allows for a direct connection through a PC to the console port on the device. The PC will need a terminal emulation program (such as HyperTerminal and PuTTY) to connect to the device's command line interface. In the terminal emulation program, use the following settings:
9600 baud (or a rate supported by your router) Data bits = 8 (default) Parity = None (default) Stop bits = 1 (default) Flow control = None
Virtual Terminal (VTY)
A VTY connection connects through a LAN or WAN interface configured on the device. Use a program such as Telnet or SSH to open the command line interface. The Cisco device must be configured with an IP address before a VTY connection can be made.
Security Device Manager (SDM)
The Cisco SDM allows a Web browser connection to the device. Once connected, the SDM allows you to manage the security features and network connections through a Web-based graphical user interface. Be aware of the following SDM settings:
10.10.10.1 is the default IP address of the SDM The default value for both the username and password is cisco
Note: A new router may not be completely configured for an SDM connection, so you may need to make a console connection first.
-
Use the following cable types to make the initial connection to the switch or the router for device management:
Cable Type Pin-outs Use
Rollover Cable
1 --> 82 --> 73 --> 64 --> 55 --> 46 --> 37 --> 28 --> 1
Use a rollover Ethernet cable to connect the device's console port to the serial port on a PC. Connect the RJ-45 end to the console port, and connect the serial end to the PC.
Straight-through Ethernet Cable
1 --> 12 --> 23 --> 36 --> 6
Use a straight-through Ethernet cable to connect an Ethernet port on a router to an Ethernet port on a hub or switch. You can then access the router from another PC connected to the same network using a VTY connection.
Note: If the router has an AUI port,connect one end to an AUI transceiver before connecting to the router.
Crossover Ethernet Cable
1 --> 32 --> 63 --> 16 --> 2
Use a crossover Ethernet cable to connect an Ethernet port on a router directly to the NIC in a PC. Establish a VTY session from the PC to connect to the device.
Note: If the router has an AUI port, connect one end to an AUI transceiver before connecting to the router.
-
System Startup
As you study this section, answer the following questions:
If the router can't find an IOS image in flash, where will it look next? What happens if the router can't find a configuration file at startup? What is the role of the configuration register? What configuration register value tells the router to skip the startup-config file?
After finishing this section, you should be able to complete the following tasks:
Use setup mode to complete an initial configuration of a Cisco device. Use the Express setup to configure a Cisco device.
This section covers the following exam objectives:
205. Perform and verify initial switch configuration tasks including remote access management
402. Describe the operation of Cisco routers (including: router bootup process, POST, router components)
Startup Facts
The following graphic details the process used to boot the device.
When you turn the router on, it runs through the following boot process.
1. The Power-On Self Test (POST) checks the router's hardware. When the POST completes successfully, the System OK LED indicator comes on.
2. The router checks the configuration register to identify where to load the IOS image from. A setting of 0x2102 means that the router will use information in the startup-config file to
-
locate the IOS image. If the startup-config file is missing or does not specify a location, itwill check the following locations for the IOS image:
1. Flash (the default location) 2. TFTP server 3. ROM (used if no other source is found)
3. The router loads the configuration file into RAM (which configures the router). The router can load a configuration file from:
1. NVRAM (startup-configuration file) 2. TFTP server 3. If a configuration file is not found, the router starts in setup mode.
Setup Mode Facts
If the router is brand new, it has no startup-config file. Therefore, when it boots, it immediately enters Setup mode. Setup mode is a special, guided routine that asks you a series of questions and uses your responses to make basic configuration entries.
There are two ways to enter setup mode:
Boot the router without the startup-config file. This happens when you erase the current startup-config file, or when you boot a new router.
Use the setup command from privileged mode.
You can exit setup mode without answering all the questions by pressing Ctrl + C. The information you've entered to that point will not be saved.
Cisco routers and switches come with the following defaults:
No set passwords. During setup mode, passwords are created. All router interfaces are in shutdown mode until they are enabled. All switch interfaces are enabled and ready to forward packets.
Note: Some Cisco switches allow you to enter an express setup mode. Be aware of the following express setup details:
The device must be enabled as a DHCP server. The device must be power cycled while pressing the Mode button and while your PC is
connected to an Ethernet interface. Use a Web browser to enter the express setup mode by going to 10.10.10.1.
-
Command Line Interface (CLI)
As you study this section, answer the following questions:
What router mode is indicated by the # prompt? How can you get a list of allowed keywords for a command? You use help to get a list of keywords for a command. In the list of options you see:
A.B.C.D. What should you type to complete the command? How can you move the cursor backwards one word? How do you turn off console configuration messages?
After finishing this section, you should be able to complete the following tasks:
Use help to identify possible commands, keywords, and parameters. Use advanced editing features to efficiently enter commands at the console. Turn on and access commands in the history buffer.
This section covers the following exam objectives:
205. Perform and verify initial switch configuration tasks including remote access management
405. Access and utilize the router to set basic parameters Command Mode Prompts and Commands The following table summarizes basic command mode prompts and other commands.
Mode Prompt To Enter To Exit
User EXEC Router> Press , then log inexitlogoutdisconnect
Privileged EXEC
Router# enable disable (exit disconnects)
Global Configuration
Router(config)# config terminal exit, ^Z*
LineRouter(config-line)# line exit, ^Z*
InterfaceRouter(config-if)# interface exit, ^Z*
SubinterfaceRouter(config-subif)#
interface . exit, ^Z*
RouterRouter(config-router)#
router exit, ^Z*
SetupNone, interactive dialog
setuperase startup-config + reload
^C
ROM Monitor
rommon>
ROM Monitor mode lets you configure your router if the router can't find a valid system image, or if the boot sequence is interrupted when you start the router. It is an emergency command-line access to the router. To go to EXEC mode from this mode, type continue at the prompt.
RXBoot RXBoot mode lets a router boot with a limited version of the IOS when it cannot
-
find a valid IOS image in Flash. You enter RXBoot mode by modifying the configuration register before rebooting the router.
*^Z (Ctrl + Z) exits all configuration modes to privileged EXEC mode. exit "backs up" one configuration mode.
Command Help Facts Help is available in all device modes. It is context sensitive, so the information you see
depends on what you are doing. Cisco bases this on the mode you are in and the words or partial words you type with the ?.
To... Use...
Show list of all commands available in the current mode
?
Show commands that begin with specific letter(s) xx? (no space between the letter and ?)
Show keywords for a command command ? (space between command and ?)
Get the full command from a partial command partial command + (no space)
Note: Typing ? acts as a return, and repeats the last command you entered after the Help information displays. You do not need to retype the command after you ask for help on it.
When you use Help to display the possible keywords for a command, you will see the following types of items.
When you see... Supply...
WORD (in caps) Type a one-word response
LINE (in caps) Type a multiple-word response
Enter a number within the range in brackets
Enter a hexadecimal number within the range in brackets
The command is complete as typed, press Enter to execute the command
A.B.C.D Enter an IP address
Editing Features Facts
The following lists summarize the advanced editing features of the CLI.
Use this ... To ...
Ctrl + A Move to the beginning of the line
Ctrl + E Move to the end of the line
Ctrl + BLeft arrow
Go back one character
Ctrl + FRight arrow
Go forward one character
Esc, then B (press and release Esc, before pressing B)
Go back one word
Esc, then F(press and release Esc, before pressing F)
Move forward one word
-
Ctrl + Z Quit a configuration mode
terminal editing Turn advanced editing on
terminal no editing Turn advanced editing off
When you are in advanced editing mode, the $ indicator appears after the prompt. As you type, commands longer than the command line appear to scroll under the prompt.
Note: The editing feature uses the same keystrokes as UNIX emacs editing.
Command History Command List
By default, the IOS automatically saves the last 10 commands in the command history buffer. The command history is specific to the configuration mode you are in.
Use . . . To . . .
Ctrl + P or Up arrow Show the previous command
Ctrl + N or Down arrow Show the next command
terminal history Turn the command history on
terminal no history Turn the command history off
terminal history size Set the size of the history buffer
show history Show all the commands in the history buffer
Controlling Screen Output
As you work with the device at the console and make configuration changes, response messages are often displayed on the screen. The following table describes various ways to control the response messages shown.
Problem Solution
When making configuration changes, the following message is constantly displayed (sometimes as you are typing):%SYS-5-CONFIG_1: Configured from console by console
Use: no logging consoleto turn these messages off.
When working with the device through a Telnet session, when you use a debug command, output will not be shown.
Use: terminal monitorto send debug output to the telnet session.
When viewing debug information, you want to review previous information, or debug information is shown too quickly for you to examine it.
Use: logging bufferedto send logging information to RAM, then use:show logto view information one screen at a time.
-
Managing System Files
As you study this section, answer the following questions:
Where is the startup-config file stored? Where is the running-config file stored? What is stored in ROM? What is the generic syntax for loading a configuration file into RAM? What does the boot system command do?
After finishing this section, you should be able to complete the following tasks:
Save your configuration changes. Load an IOS image from an alternate location. Upgrade the IOS image.
This section covers the following exam objectives:
405. Access and utilize the router to set basic parameters 409. Manage IOS configuration files (including: save, edit, upgrade, restore) 410. Manage Cisco IOS Router Memory Be sure you understand the difference between the following types of router storage.
Memory Type Characteristics
ROM (Read-Only Memory)
Preprogrammed, non-writable memory containing the bootstrap startup program, an older, smaller-scale version of the operating system (IOS) software, and the Power-on Self-Test (POST) program
FlashNon-volatile but programmable memory containing the proprietary Cisco operating system (IOS) imagesNote: Older routers dont have flash memory
RAM (Random Access Memory)
Volatile memory containing the running operating system and current (unsaved) configuration information
NVRAM (Non-Volatile RAM)
Non-volatile but persistent memory that contains the backup copy of the startup configuration (startup-config) file and virtual configuration registerNote: On some routers, NVRAM holds the IOS image
The contents of non-volatile memory (such as ROM, flash, and NVRAM) remain when the router is powered off. The contents of volatile memory (RAM) are lost when the router is powered down.
Copy Command List
The device can load a configuration file from:
NVRAM (startup-configuration file by default value 0x2102) TFTP server
Changes to the configuration are stored in RAM in the running-config file. To save your configuration changes permanently, and to load different versions of the configuration files from various locations, use the copy command in privileged EXEC mode.
Use . . . To . . .
Router#copy run start Save the contents of the running-config file to NVRAM
-
Router#copy start run Copy the startup-config file into RAM
Router#copy run tftp Save the contents of the running-config file to a TFTP server
Router#copy start tftp Save the contents of the startup-config file to a TFTP server
Router#copy tftp start Copy a configuration file from the TFTP server into NVRAM
Router#copy tftp run Copy a configuration file from the TFTP server into RAM
Router(config)#tftp-server flash
Configure a Cisco router as a TFTP server. When using this command, you must specific the location (flash or rom) of the IOS image file as well as the IOS image file name.
You can also use the erase command to delete the configuration files--but be very careful not to erase files you need!
Use . . . To . . .
Router#erase flash Delete the contents of Flash memory (deletes the IOS image)
Router#erase start Erase the contents of the startup-config file
Router#erase nvram Delete the contents of NVRAM (which also erases startup-config)
Router#reload Restarts the router
You can also use the following commands to manage system files:
Use . . . To . . .
show version Display information about hardware and firmware including the configuration register value
configure memoryorcopy startup-config running-config
Copy configuration information from another source (like NVRAM)
configure terminal Configure information into the RAM of a router
IOS Boot and Upgrade Location Command List
The router can load an IOS image from the following locations:
Flash TFTP server ROM (limited version of the IOS software)
Use the boot system command in global configuration mode to identify alternate locations for the IOS image. Use the copy command to archive, upgrade, or replace an IOS image.
Use . . . To . . .
Router(config)#boot system flash
Identify an IOS image file in flash to use at boot.
Router(config)#boot system tftp
Identify an IOS image file on a TFTP server to use at boot.
-
Router(config)#boot system rom (IOS versions 11.2 and below)Router(config)#boot system flash bootflash: (IOS versions 12.0 and above
Specify to use the limited IOS version stored in ROM at boot.
Router#copy flash tftp Back up (copy) the IOS image from Flash to the TFTP server.
Router#copy tftp flash Restore the IOS image from backup on the TFTP server to Flash.
Note: When you use the boot system command, you are not making backup copies of the IOS image, nor are you replacing the default IOS search order. You are directing the router where to look for the IOS image on boot-up. It tries each location in turn, until it finds a valid IOS image. If one is not found, it returns to the default load sequence.
-
Using Show Commands
After finishing this section, you should be able to complete the following tasks:
Use show commands to find information about the device configuration.
This section covers the following exam objectives:
215. Interpret the output of various show and debug commands to verify the operational status of a Cisco switched network
416. Verify router hardware and software operation using SHOW & DEBUG commands Show Command List (Basic) The following list summarizes common information you can display using common show
commands.
Use this command... To...
show version View hardware configuration, running IOS version, ROM bootstrap version, and RAM and processor information
show running-config View the currently running configuration file
show startup-configorshow config
View the startup configuration file stored in NVRAM (the saved copy of the configuration file)
show flash View the size of the configuration files and the available flash memoryView information for all IOS image files stored on the router
show history View the commands in the command history list
show protocolsorshow interfacesorshow ip interfaces
View the IP addresses assigned to a specific interface
show protocolsorshow interfaces
View the status of all interfaces
-
Hostname and Descriptions
As you study this section, answer the following questions:
When is the Slot/Sub-slot/Port numbering used? How do fixed ports and WIC slots affect the numbering scheme for a device? What changes in the prompt after you set a hostname?
After finishing this section, you should be able to complete the following tasks:
Change the device host name. Configure descriptions on device interfaces.
This section covers the following exam objectives:
205. Perform and verify initial switch configuration tasks including remote access management
405. Access and utilize the router to set basic parameters 406. Connect, configure, and verify operation status of a device interface
Interface Numbering Facts
The switch interface numbering scheme includes the bank number and port number:
Portion Details Examples
Bank number
Switches that have one fixed bank are assigned 0. Switches that have multiple banks start with 0 and are
assigned from bottom to top. For example, if a switch had 5 banks, it would have bank numbers 0-4.
FastEthernet 2/1 (3rd bank/1st port)FastEthernet 1/5 (2nd bank/5th port)FastEthernet 0/7 (fixed bank or 1st bank/7th port)FastEthernet 5/1 (6th bank/1st port)
Port number
Port numbers are assigned starting with 1. Switches that have 1 row of ports on a bank are
assigned from left to right. Switches that have 2 rows of ports on a bank are
assigned from top to bottom and left to right.
Router interface numbering includes the following types of schemes:
Scheme Details Examples
Fixed ports
Older Cisco routers, such as the Cisco 2500, use a fixed port numbering scheme. In the fixed port numbering scheme:
Each built-in port was hard-wired with a port number.
Numbering starts with 0, and is assigned from right to left.
Serial0 (1st serial port)Serial1 (2nd serial port)Ethernet0 (1st Ethernet port)
Slot/Port numbering
Newer Cisco routers, such as the Cisco 2600, support WAN Interface Cards (WIC) and Network Modules (NM) with various ports. Some Network Modules include slots
FastEthernet3/4 (3rd NM slot/5th FastEthernet port)
-
for WAN Interface Cards. In the Slot/Port numbering scheme:
The slot number scheme includes: o Built-in ports and built-in WIC slots are
given NM slot number 0. The remaining NM slots are assigned from right to left and bottom to top.
o If the device does not have built-in ports or built-in WIC slots, the NM slot numbering is assigned from right to left and bottom to top, starting with 0.Note: When learning about the router's NM slots, discover whether or not the router has built-in ports and built-in WIC slots.
The port numbers start with 0 and are assigned from right to left and bottom to top for each NM slot.
FastEthernet0/3 (built-in/4th FastEthernet port)
Serial2/3 (2nd NM slot/4th serial port)Serial1/5 (1st NM slot/6th serial port)Serial0/2 (built-in or 1st WIC slot/3rd serial port)
Slot/Sub-slot/Port numbering
The newest Cisco routers, such as the Cisco 1800/2800/3800, use an enhanced slot/port numbering scheme to identify the WIC sub-slot. In the Slot/Sub-slot/Port numbering scheme:
Built-in WIC ports are numbered using a slot of 0 and a sub-slot that is the WIC slot number.
WIC ports on a NM slot are numbered using the NM slot number and the WIC's sub-slot number on the NM.
Ports (other than those of a WIC) use the slot/port numbering scheme.
FastEthernet2/1/0 (2nd NM slot/2nd WIC sub-slot/1st FastEthernet port)FastEthernet0/0/0 (built-in/1st WIC sub-slot/1st FastEthernet port)FastEthernet0/1/3 (built-in/2nd WIC sub-slot/4th FastEthernet port)
Serial4/1/1 (4th NM slot/2nd WIC sub-slot/2nd Serial port)Serial0/1/0 (built-in/2nd WIC sub-slot/1st Serial port)
Ethernet1/0 (1st NM slot/1st Ethernet port)FastEthernet0/1 (built-in/2nd FastEthernet port)
Hostname and Description Command List
During initial setup, you can configure a host name for your device (i.e. router or switch). This is the name that appears in the EXEC prompt. Unlike the device itself, interfaces do not have specific names that change the prompt. However, you can add a description to the configuration file that helps you identify the interface.
Use . . . To . . .
Router(config)#hostname Change the host name of the router
Router(config)#int serial 0/0Router(config)#int s0/0
Go to interface configuration mode for the first serial interface. You can use abbreviations for the
-
Router(config)#int Ethernet 0Router(config)#int ether0Router(config)#int FastEthernet 0/1Router(config)#int Fa0/1Router(config)#int Gigabit 0/1Router(config)#int gi0/1
interface type, such as:
fa = FastEthernet gi = Gigabit s = Serial e = Ethernet
Router(config-if)#description Set a description for a specific interface
ExamplesThe following set of commands sets the hostname of the router to ATL1:
Router#config tRouter(config)#hostname ATL1ATL1(config)#
The following set of commands adds a description of ATL to NYC for the first serial interface on the router:
Router(config)#int ser 0Router(config-if)#description ATL to NYC
Note: To undo any configuration change, use the same command preceded by the no keyword followed by the command. For example, to remove a description from an interface, use the following command:
Router(config-if)#no description
Notice that in many cases you can leave off additional parameters when using the no command.
-
System Passwords
As you study this section, answer the following questions:
What is the difference between the enable and the enable secret passwords? Which one is more secure?
How would you require a password when logging on through the console? You have configured the VTY lines on a router with a password but you did not use the
login command. Will VTY login be allowed? Will a password be required? What must you do to disable VTY login?
After finishing this section, you should be able to complete the following tasks:
Configure router passwords including: enable, console, and VTY. Restrict console and VTY access to a Cisco device. Recover device passwords.
This section covers the following exam objectives:
205. Perform and verify initial switch configuration tasks including remote access management
405. Access and utilize the router to set basic parameters 417. Implement basic router security
Device Password Facts
The following table lists three of the most common passwords that you can configure on your device:
Password Type
Description
Console Controls the ability to log on to the router through a console connection
VTY Controls the ability to log on to the router using a virtual terminal (VTY) connection
EXEC mode
Controls the ability to switch to configuration modes. There are two different passwords that might be used:
The enable password is stored in clear text in the configuration file. The enable secret password is stored encrypted in the configuration file.
Note: The router always uses the enable secret password if it exists.
Be aware of the following recommendations for configuring router passwords:
Passwords are case-sensitive. For security reasons, you should not use the same password for both your enable and enable
secret passwords. You can set the enable, enable secret, and line passwords in setup mode. Cisco routers support Terminal Access Controller Access Control System (TACACS) and
Remote Authentication Dial-In User Service (RADIUS) to centrally validate users attempting to gain access to the router.
The following table summarizes basic password commands.
-
Use . . . To . . .
Router(config)#enable secret
Set the encrypted password used for privileged mode access. The enable secret is always used if it exists.
This command uses the Message-Digest 5 (MD5) hashing algorithm to encrypt the password.
Router(config)#enable password
Set the unencrypted password for privileged mode access. This password is used if the enable secret is not set.
Router(config)#line con 0 Switch to the line configuration mode for the console.
Router(config)#line vty
Switch to the line configuration mode for the virtual terminal. Specify one line number or a range of line numbers, for example: line vty 0 4
Router(config-line)#password Set the line password (for either console or VTY access).
Router(config-line)#login Require the password for line access.Router(config)#no enable secretRouter(config)#no enable passwordRouter(config-line)#no loginRouter(config-line)#no password
Remove the password. The no login command disables password checking.
Router(config)#service password-encryption
Encrypt all passwords as a type 7 password. Encrypted type 7 passwords are not secure and can be easily broken; however, the encrypted values do provide some level of protection from someone looking over your shoulder after having issued the show run command. Rather than relying on this encryption, make sure to use the enable secret command for better encryption.
Note: If you do not use the login command in line mode, a password will not be required for access, even though one is set.
Access to the console through a Telnet session is controlled by the login and the password entries. To prevent VTY access, there must be a login entry without a password set. Access is allowed based on the following conditions:
no login, no password = access is allowed without a password login, no password = access is denied (the error message indicates that a password is
required but none is set) no login, password = access is allowed without a password login, password = access is allowed only with correct password
Password Recovery Facts
Password recovery is the process of discovering or resetting forgotten router passwords. The exact process you use to recover lost passwords depends on the switch model. Listed below are the general steps you would take for the 2960 switch:
1. Establish a console connection to the switch. 2. Unplug the power cable. 3. Hold down the mode button while reconnecting the power cable to the switch. Release the
mode button when the SYST LED blinks amber and then turns solid green. When you release the mode button, the SYST LED blinks green.
4. Type the flash_init command.
-
5. Type the load_helper command. 6. Type the dir flash: command. Note: make sure to include the colon (:). 7. Type rename flash:config.text flash:config.old to rename the configuration file. 8. Type the boot command to restart the system. 9. Enter yes to terminate autoinstall. 10. Enter n at the prompt to abort the initial configuration dialog. 11. Type enable to enter enable mode.
o To save the previous settings and configurations of the switch, type rename flash:config.old flash:config.text
o To overwrite the settings and configurations of the switch, type copy flash:config.text system:running-config to copy the configuration file into memory. Note: the configuration file is now reloaded.
12. Enter configuration mode to change the passwords. 13. In global EXEC mode, type copy run start to save the changes.
To recover passwords on most routers, you need to modify the configuration register to bypass the startup-config file and boot the router with a limited IOS version. You can then load the existing startup-config file and view or modify the current password settings. The exact process you use to recover lost passwords depends on the router model. Listed below are the general steps you would take for the 1800 series routers:
1. Establish a console connection to the router. 2. At the prompt, type show version. Record the value for the configuration register (usually
0x2102). 3. Turn the router off and on. 4. Within 60 seconds, use the keyboard to send a break sequence to the router. For a Windows
system, the break sequence is typically one of the following: o Break + F5o Shift + F5 o ^$B (Shift + 6, Shift + 4, Shift + b)
5. Type confreg 0x2142 to change the configuration register setting. 6. Type reset or i to reboot. With the configuration register changed, the router reboots
bypassing the startup-config file. 7. The router will automatically enter Setup mode. At this point you can:
o Use Setup mode to configure the router (including the passwords). o Quit Setup mode (using Ctrl + C) and change only the existing passwords.
1. Type enable to enter privileged EXEC mode. 2. Type copy start run to load the startup-config file. 3. Enter configuration mode to change the passwords. 4. Type config-register 0x2102 to change the configuration register back to the
default. 5. Exit configuration mode and use copy run start to save the changes to the
passwords. 8. Use the reload command to restart the router normally.
-
Banners
As you study this section, answer the following questions:
When do each of the banners display? What banner do you configure if you use the banner command without specifying the
banner type? What is the role of the delimiting character? You type the following command at the router: banner exec this is it. What will show
following a successful login?
After finishing this section, you should be able to complete the following tasks:
Configure, modify, and delete router banners.
This section covers the following exam objectives:
205. Perform and verify initial switch configuration tasks including remote access management
405. Access and utilize the router to set basic parameters 417. Implement basic router security
Banner Command List
Banners display messages that anyone logging into the device can see. The following four types of banners display at various times during the login or startup sequence.
Use . . . To . . .
Router(config)#banner Router(config)#banner motd
Set the Message-of-the-day (MOTD) banner. The MOTD banner displays immediately after a connection is made.
Router(config)#banner login
Set the login banner. The login banner displays after the MOTD banner and before the login prompt.
Router(config)#banner exec
Set the EXEC banner. The exec banner displays after a successful login.
Router(config)#banner incoming
Set the incoming banner. The incoming banner displays for a reverse telnet session.
Router(config)#no banner Removes the specified banner
Note: The banner command without a keyword defaults to set the MOTD banner.
Follow the banner command with a delimiting character. The delimiter encloses the banner text, and helps the router identify the beginning and ending of the banner. This allows you to construct multiple-line banners.
ExampleThe following commands set the MOTD, login, and EXEC banners, using # as the delimiting character and inserting a hard return between each banner:
Router(config)#banner motd # This is the Message-of-the-day banner! #Router(config)#banner login # This is the Login banner! #Router(config)#banner exec # This is the Exec banner!
-
#
-
Cisco Discovery Protocol (CDP)
As you study this section, answer the following questions:
What are the requirements for using CDP? You have not yet configured an IP address on a Cisco router, but the interface is up. Will
the router be able to use CDP to discover neighboring device information? You want to view information about a router that is two hops away? How can you view this
information? How do you turn off CDP advertisements for a single interface? How do you disable CDP
on a router?
After finishing this section, you should be able to complete the following tasks:
Use CDP to view information about neighboring devices. Enable and disable CDP on devices and specific interfaces. Configure CDP timers.
This section covers the following exam objectives:
205. Perform and verify initial switch configuration tasks including remote access management
405. Access and utilize the router to set basic parameters 406. Connect, configure, and verify operation status of a device interface
CDP Command List
The Cisco Discovery Protocol (CDP) is a protocol that Cisco devices use to learn and share information about each other. Cisco devices, such as routers and switches, can discover neighboring Cisco devices through CDP.
By default, CDP is enabled on all interfaces. CDP only shares information with directly connected (neighboring) devices. CDP works when there is a valid Data Link layer connection. CDP works regardless of the Network layer and other protocols used. It can discover
information on LANs, Frame Relay, and other network architectures.
Use the following commands to customize and view CDP information.
Use . . . To . . .
Router(config)#cdp holdtime
Specify the amount of time that information in a packet is still valid (default = 180 seconds)Use the no cdp holdtime command to reset the value to its default.
Router(config)#cdp timer
Specify how often CDP packets are exchanged (default = 60 seconds)Use the no cdp timer command to reset the value to its default.
Router(config)#cdp run Enable CDP on the router
Router(config)#no cdp runDisable CDP on a router, to prevent the router from exchanging CDP packets
Router(config-if)#cdp enable Turns CDP for an interface on
-
Router(config-if)#no cdp enable Turns CDP for an interface off
Router#show cdp View CDP information
Router#show cdp interface
Show information about neighbors accessed through an interfaceShow CDP configuration information for the router including the holdtime, encapsulation, and CDP exchange interval
Router#show cdp neighbors
Show information about all neighboring Cisco devices including:
Device ID Local interface Holdtime Capability Platform Port ID
Router#show cdp neighbor