cdx gt61uigt610ui

48
SERVICE MANUAL Sony Corporation eVehicle Division Published by Sony Techno Create Corporation US Model 9-887-538-02 2007D04-1 © 2007.04 Ver. 1.1 2007.04 SPECIFICATIONS CD player section Signal-to-noise ratio 120 dB Frequency response 10 – 20,000 Hz Wow and flutter Below measurable limit Tuner section FM Tuning range 87.5 – 107.9 MHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 9 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz 0.5% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz AM Tuning range 530 – 1,710 kHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 V USB player section Interface USB (Full-speed) Maximum current 500 mA Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 52 W 4 (at 4 ohms) • The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism CDX-GT41UW/GT410U CD Drive Mechanism Type MG-101U-188//Q Optical Pick-up Name DAX-25A – Continued on next page – CDX-GT61UI/GT610UI FM/AM COMPACT DISC PLAYER (Photo: CDX-GT61UI) AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion.

Upload: michael-angel-lunasco

Post on 26-Oct-2014

155 views

Category:

Documents


2 download

TRANSCRIPT

Page 1: Cdx Gt61uigt610ui

SERVICE MANUAL

Sony CorporationeVehicle DivisionPublished by Sony Techno Create Corporation

US Model

9-887-538-022007D04-1© 2007.04

Ver. 1.1 2007.04

SPECIFICATIONS

CD player sectionSignal-to-noise ratio 120 dBFrequency response 10 – 20,000 HzWow and flutter Below measurable limit

Tuner sectionFMTuning range 87.5 – 107.9 MHzAntenna terminal External antenna connectorIntermediate frequency 10.7 MHz/450 kHzUsable sensitivity 9 dBfSelectivity 75 dB at 400 kHzSignal-to-noise ratio 67 dB (stereo), 69 dB (mono)Harmonic distortion at 1 kHz

0.5% (stereo), 0.3% (mono)Separation 35 dB at 1 kHzFrequency response 30 – 15,000 Hz

AMTuning range 530 – 1,710 kHzAntenna terminal External antenna connectorIntermediate frequency 10.7 MHz/450 kHzSensitivity 30 µV

USB player sectionInterface USB (Full-speed)Maximum current 500 mA

Power amplifier sectionOutputs Speaker outputs (sure seal connectors)Speaker impedance 4 – 8 ohmsMaximum power output

52 W × 4 (at 4 ohms)

• The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism CDX-GT41UW/GT410U

CD Drive Mechanism Type MG-101U-188//Q

Optical Pick-up Name DAX-25A

– Continued on next page –

CDX-GT61UI/GT610UI

FM/AM COMPACT DISC PLAYER

(Photo: CDX-GT61UI)

AUDIO POWER SPECIFICATIONSPOWER OUTPUT AND TOTAL HARMONIC DISTORTION23.2 watts per channel minimum continuous average power into4 ohms, 4 channels driven from 20 Hz to 20 kHz with no morethan 5% total harmonic distortion.

Page 2: Cdx Gt61uigt610ui

2

CDX-GT61UI/GT610UI

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostaticbreakdown because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic breakdown and also usethe procedure in the printed matter which is included in the repairparts.The flexible board is easily damaged and should be handled withcare.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.

If the optical pick-up block is defective, please replace the wholeoptical pick-up block.Never turn the semi-fixed resistor located at the side of optical pick-up block.

SERVICE NOTES

CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.

GeneralOutputs Audio outputs terminal (sub/rear switchable)

Power antenna relay control terminalPower amplifier control terminal

Inputs BUS control input terminalBUS audio input terminalAntenna input terminalAUX input jack (stereo mini jack)iPod signal input terminal (dock connector)

Tone controls Low: ±10 dB at 60 Hz (XPLOD)Mid: ±10 dB at 1 kHz (XPLOD)High: ±10 dB at 10 kHz (XPLOD)

Power requirements 12 V DC car battery (negative ground)Dimensions Approx. 178 × 50 × 179 mm

(7 1/8 × 2 × 7 1/8 in.) (w/h/d)Mounting dimensions Approx. 182 × 53 × 162 mm

(7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d)Mass Approx. 1.3 kg (2 lb. 14 oz.)Supplied accessories Card remote commander: RM-X151

Parts for installation and connections (1 set)USB cap

Design and specifications are subject to change withoutnotice.

US and foreign patents licensed from Dolby Laboratories.optical pick-up

semi-fixed resistor

Notes on Chip Component Replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be damaged

by heat.

TEST DISCSPlease use the following test discs for the check on the CD section.

YDES-18 (Part No. 3-702-101-01)PATD-012 (Part No. 4-225-203-01)

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.

Page 3: Cdx Gt61uigt610ui

3

CDX-GT61UI/GT610UI

•UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.

• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.

• CD playbackYou can play CD-DA (also containing CD TEXT*), CD-R/CD-RW (MP3/WMA/AAC files also containing Multi Session) andATRAC CD (ATRAC3 and ATRAC3plus format).

Type of discs Label on the disc

CD-DA

MP3

WMA

AAC

ATRAC CD

* A CD TEXT disc is a CD-DA that includes information such asdisc, artist and track name.

TABLE OF CONTENTS

1. SERVICE NOTE ........................................................ 4

2. GENERALLocation of Controls ........................................................ 5Connections ..................................................................... 6

3. DISASSEMBLY3-1. Sub Panel (FL-U) Assy .................................................... 113-2. CD Mechanism Block ..................................................... 113-3. Main Board ...................................................................... 123-4. Servo Board ..................................................................... 123-5. Chassis (T) Sub Assy ....................................................... 133-6. Roller Arm Assy .............................................................. 133-7. Chassis (OP) Assy ........................................................... 14

4. DIAGNOSIS FUNCTION ........................................ 15

5. DIAGRAMS5-1. Block Diagram –Main Section– ...................................... 195-2. Block Diagram –Display Section– .................................. 205-3. Printed Wiring Board –Main Section– ............................ 225-4. Schematic Diagram –Main Section (1/4)– ...................... 245-5. Schematic Diagram –Main Section (2/4)– ...................... 255-6. Schematic Diagram –Main Section (3/4)– ...................... 265-7. Schematic Diagram –Main Section (4/4)– ...................... 275-8. Printed Wiring Board –Key Section– .............................. 285-9. Schematic Diagram –Key Section– ................................. 29

6. EXPLODED VIEWS6-1. Main Section.................................................................... 356-2. Front Panel Section ......................................................... 366-3. CD Mechanism Section (MG-101U-188//Q) .................. 37

7. ELECTRICAL PARTS LIST .................................. 38

Ver. 1.1

Page 4: Cdx Gt61uigt610ui

4

CDX-GT61UI/GT610UISECTION 1

SERVICE NOTE

SERVO BOARDCN2

MAIN BOARDCN350 J-2502-076-1

EXTENSION CABLE AND SERVICE POSITIONWhen repairing or servicing this set, connect the jig (extension cable)as shown below.

• Connect the MAIN board (CN350) and the SERVO board (CN2)with the extension cable (Part No. J-2502-076-1).

NOTE FOR THE 24-PIN CONNECTOR (CN901)Do not use alcohol to clean the 24-pin connector (CN901) connectingthe front panel with the main body.Do not touch the connector directly with your bare hand. Poor contactmay be caused.

NOTE FOR REPLACEMENT OF THE SERVO BOARDWhen repairing, the complete SERVO board (A-1206-357-A) shouldbe replaced since any parts in the SERVO board cannot be repaired.

NOTE FOR REPLACEMENT OF THE USB CONNECTOR(CN902)To replace the USB connector requires alignment.1. Insert the USB connector into the front panel.2. Place the KEY board on the front panel and align the terminals

of the USB connector with the holes in the KEY board.3. Solder the four terminals of the connector.

KEY board

front panel

USB (socket) connector

Page 5: Cdx Gt61uigt610ui

5

CDX-GT61UI/GT610UISECTION 2GENERAL This section is extracted

from instruction manual.

• LOCATION OF CONTROLS• CDX-GT61UI

• CDX-GT610UI

6

Location of controls and basic operations

Main unit

Card remote commander RM-X151

Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.

A OFF buttonTo power off; stop the source.

B EQ3 (equalizer) button 12To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF).

C Volume control dial/select button 12To adjust volume (rotate); select setup items (press and rotate).

D SOURCE buttonTo power on; change the source (Radio/CD/MD*1/USB/AUX/PD/SAT*2).

E Disc slotInsert the disc (label side up), playback starts.

F Display window

G USB terminal 9To connect to the USB device.

H Z (eject) buttonTo eject the disc.

I BTM/CAT*2 button 8To start the BTM function (press and hold).

J (front panel release) button 5

AUX

OFF

BTM

DSPL

MODE

SCRL

PUSH SELECT

SEEK SEEK

PAUSEDIM REP SHUF

EQ3 SOURCE

1 2 3 4 5 6

CAT

GP/ALBM

12

qjqh

4 5 863

CDX-GT61UI

qa qdq;9 qs qfqg

7

qk

OFF

DSPL SCRL

SELSOURCE MODE

1 32

4 65

ATT

VOL+

+

4 wsqd

1

qj

ql

qf

wa

w;

wf

wd

7

K SEEK –/+ buttonsCD/MD*1/USB*3/PD*4:To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fast-forward a track (press and hold).Radio:To tune in stations automatically (press); find a station manually (press and hold).

L Receptor for the card remote commander

M MODE button 8, 10, 13To select the radio band (FM/AM); select the SAT tuner band (mode)*2; select the unit*5; select the play mode*4*6.

N DSPL (display)/DIM (dimmer) button 8, 9, 11To change display items (press); change the display brightness (press and hold).

O RESET button (located behind the front panel) 4

P Number buttonsCD/MD*1/USB*3/PD*4:(1)/(2): GP*7/ALBM*8 –/+

To skip groups/albums (press); skip groups/albums continuously (press and hold)*9.

(3): REP 8, 10, 11, 14(4): SHUF 8, 10, 11, 14(5): 11(6): PAUSE*10

To pause playback. To cancel, press again.

Radio:To receive stored stations (press); store stations (press and hold).

Q SCRL (scroll) button 8, 9, 11To scroll the display item.

R AUX input jack 13To connect a portable audio device.

The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4).

ql < (.)/, (>) buttonsTo control CD/radio/MD/USB/PD, the same as (SEEK) –/+ on the unit.

w; VOL (volume) +/– buttonTo adjust volume.

wa ATT (attenuate) buttonTo attenuate the sound. To cancel, press again.

ws SEL (select) buttonThe same as the select button on the unit.

wd M (+)/m (–) buttonsTo control CD, the same as (1)/(2) (GP/ALBM –/+) on the unit.

wf Number buttonsTo receive stored stations (press); store stations (press and hold).

*1 When an MD changer is connected.*2 When the SAT tuner is connected.*3 When a USB device is connected.*4 When an iPod is connected.*5 When a CD/MD changer is connected.*6 When an ATRAC Audio Device is connected.*7 When an ATRAC CD is played.*8 When an MP3/WMA/AAC is played.*9 If the changer/iPod is connected, the operation is

different, see page 11, 13.*10When playing back on this unit.

Notes• When ejecting/inserting a disc, keep any USB

devices disconnected to avoid damage to the disc.• If the unit is turned off and the display disappears, it

cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.

TipFor details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 16.

About USB capWhen not using the USB terminal (G), use the supplied USB cap to prevent dust or dirt entering.Keep the USB cap out of the reach of children to prevent accidental swallowing.

6

Location of controls and basic operations

Main unit

Card remote commander RM-X151

Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.

A OFF buttonTo power off; stop the source.

B EQ3 (equalizer) button 12To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF).

C Volume control dial/select button 12To adjust volume (rotate); select setup items (press and rotate).

D SOURCE buttonTo power on; change the source (Radio/CD/MD*1/USB/AUX/PD/SAT*2).

E Disc slotInsert the disc (label side up), playback starts.

F Display window

G USB terminal 9To connect to the USB device.

H Z (eject) buttonTo eject the disc.

I BTM/CAT*2 button 8To start the BTM function (press and hold).

J (front panel release) button 5

AUX

OFF

BTM

DSPL

MODE

SCRL

PUSH SELECT

SEEK SEEK

PAUSEDIM REP SHUF

EQ3 SOURCE

1 2 3 4 5 6

CAT

GP/ALBM

12

qjqh

4 5 863

CDX-GT610UI

qa qdq;9 qs qfqg

7

qk

OFF

DSPL SCRL

SELSOURCE MODE

1 32

4 65

ATT

VOL+

+

4 wsqd

1

qj

ql

qf

wa

w;

wf

wd

7

K SEEK –/+ buttonsCD/MD*1/USB*3/PD*4:To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fast-forward a track (press and hold).Radio:To tune in stations automatically (press); find a station manually (press and hold).

L Receptor for the card remote commander

M MODE button 8, 10, 13To select the radio band (FM/AM); select the SAT tuner band (mode)*2; select the unit*5; select the play mode*4*6.

N DSPL (display)/DIM (dimmer) button 8, 9, 11To change display items (press); change the display brightness (press and hold).

O RESET button (located behind the front panel) 4

P Number buttonsCD/MD*1/USB*3/PD*4:(1)/(2): GP*7/ALBM*8 –/+

To skip groups/albums (press); skip groups/albums continuously (press and hold)*9.

(3): REP 8, 10, 11, 14(4): SHUF 8, 10, 11, 14(5): 11(6): PAUSE*10

To pause playback. To cancel, press again.

Radio:To receive stored stations (press); store stations (press and hold).

Q SCRL (scroll) button 8, 9, 11To scroll the display item.

R AUX input jack 13To connect a portable audio device.

The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4).

ql < (.)/, (>) buttonsTo control CD/radio/MD/USB/PD, the same as (SEEK) –/+ on the unit.

w; VOL (volume) +/– buttonTo adjust volume.

wa ATT (attenuate) buttonTo attenuate the sound. To cancel, press again.

ws SEL (select) buttonThe same as the select button on the unit.

wd M (+)/m (–) buttonsTo control CD, the same as (1)/(2) (GP/ALBM –/+) on the unit.

wf Number buttonsTo receive stored stations (press); store stations (press and hold).

*1 When an MD changer is connected.*2 When the SAT tuner is connected.*3 When a USB device is connected.*4 When an iPod is connected.*5 When a CD/MD changer is connected.*6 When an ATRAC Audio Device is connected.*7 When an ATRAC CD is played.*8 When an MP3/WMA/AAC is played.*9 If the changer/iPod is connected, the operation is

different, see page 11, 13.*10When playing back on this unit.

Notes• When ejecting/inserting a disc, keep any USB

devices disconnected to avoid damage to the disc.• If the unit is turned off and the display disappears, it

cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.

TipFor details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 16.

About USB capWhen not using the USB terminal (G), use the supplied USB cap to prevent dust or dirt entering.Keep the USB cap out of the reach of children to prevent accidental swallowing.

Page 6: Cdx Gt61uigt610ui

6

CDX-GT61UI/GT610UI

• CONNECTIONS• CDX-GT61UI

BBUS AUDIO IN

BUS CONTROL IN

BUS AUDIO IN

BUS CONTROL IN

iPod

iPod

Source selector*Selector de fuente*

XA-C40

* not suppliedno suministrado

Ejemplo de conexiones Notas (2-A)• Asegúese de conectar primero el cable de conexión a masa

antes de realizar la conexión del amplifi cador.• La alarma sonará únicamente si se utiliza el amplifi cador

incorporado.

Sugerencia (2-B- )Si desea conectar dos o más cambiadores de CD/MD, necesitará el selector de fuente XA-C40 (no suministrado).

Notas sobre el sintonizador de radio vía satélite (2 -C)• Esta unidad no es compatible con el adaptador

XMDSON100.• No es posible conectar más de un sintonizador de

radio vía satélite (XM/SIRIUS) al modelo XA-C40 simultáneamente.

• Cuando utilice un sintonizador de radio vía satélite, asegúrese de conectarlo al terminal INPUT 1 del XA-C40.

Connection example Notes (2-A)• Be sure to connect the ground (earth) lead before connecting

the amplifi er.• The alarm will only sound if the built-in amplifi er is used.

Tip (2-B- )For connecting two or more CD/MD changers, the source selector XA-C40 (not supplied) is necessary.

Notes on satellite radio tuner (2 -C)• This unit does not support the XMDSON100.• You cannot connect two or more satellite radio tuners

(XM/SIRIUS) to the XA-C40 at the same time. • When you use a satellite radio tuner, be sure to connect

to the INPUT 1 terminal of the XA-C40.

Page 7: Cdx Gt61uigt610ui

7

CDX-GT61UI/GT610UI

L

R

BUS AUDIO IN

AUDIO OUT REAR*2 BUS

CONTROL IN

2

4

5

1

3

AUDIO OUTREAR/SUB

BUSIN

AMP REMMax. supply current 0.3 ACorriente máx. de alimentación de 0,3 A

Fuse (10 A)Fusible (10 A)

Blue/white stripedCon rayas azules y blancas

ANT REM

RedRojo

YellowAmarillo

BlackNegro

BlueAzul

WhiteBlanco

GreenVerde

PurpleMorado

White/black stripedCon rayas blancas y negras

Gray/black stripedCon rayas grises y negras

Green/black stripedCon rayas verdes y negras

GrayGris

LeftIzquierdo

RightDerecho

*1 RCA pin cord (not supplied)*2 AUDIO OUT can be switched SUB or REAR.

For details, see the supplied Operating Instructions.

*1 Cable con terminales RCA (no suministrado)*2 AUDIO OUT (Salida de audio) puede

cambiarse a SUB (Secundaria) o REAR (Posterior). Para obtener información, consulte el manual de instrucciones suministrado.

Purple/black stripedCon rayas moradas y negras

*1

Source selector(not supplied)

Selector de fuente(no suministrado)

XA-C40

Max. supply current 0.1 ACorriente máx. de alimentación de 0,1 A

from car antenna (aerial) desde la antena del automóvil

LeftIzquierdo

RightDerecho

Supplied with XA-C40Suministrado con el XA-C40

Supplied with the CD/MD changerSuministrado con el cambiador de CD/MD

2

Diagrama de conexión

1 A una superfi cie metálica del automóvilConecte primero el cable de conexión a masa negro, y después los cables amarillo y rojo de fuente de alimentación.

2 Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplifi cador de señal de la antenaNotas• Si no se dispone de antena motorizada ni de amplifi cador

de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable.

• Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”.

3 A AMP REMOTE IN de un amplifi cador de potencia opcionalEsta conexión es sólo para amplifi cadores. La conexión de cualquier otro sistema puede dañar la unidad.

4 Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de encendidoNotas• Si no hay posición de accesorio, conéctelo al terminal de

alimentación (batería) de +12 V que recibe energía sin interrupción.Asegúrese de conectar primero el cable de conexión a masa negro a una superfi cie metáica del automó vil.

• Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”.

5 Al terminal de alimentación de +12 V que recibe energía sin interrupciónAsegúrese de conectar primero el cable de conexión a masa negro a una superfi cie metálica del automóvil.

Notas sobre los cables de control y de fuente de alimentación• El cable de control de la antena motorizada (azul) suministrará

cc de + 12 V cuando conecte la alimentación del sintonizador.• Si el automóvil dispone de una antena de FM/AM incorporada

en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de fuente de alimentación auxiliar (rojo) al terminal de alimentación del amplifi cador de antena existente. Para obtener más información, consulte a su distribuidor.

• Con esta unidad no es posible utilizar una antena motorizada sin caja de relé.

Conexión para protección de la memoriaSi conecta el cable de fuente de alimentación amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague el interruptor de encendido.

Notas sobre la conexión de los altavoces• Antes de conectar los altavoces, desconecte la alimentación

de la unidad.• Utilice altavoces con una impedancia de 4 a 8 Ω con la

capacidad de potencia adecuada para evitar que se dañen.• No conecte los terminales de altavoz al chasis del automóvil,

ni conecte los terminales del altavoz derecho con los del izquierdo.

• No conecte el cable de conexión a masa de esta unidad al terminal negativo (–) del altavoz.

• No intente conectar los altavoces en paralelo.• Conecte solamente altavoces pasivos. Si conecta altavoces

activos (con amplifi cadores incorporados) a los terminales de altavoz, puede dañar la unidad.

• Para evitar fallas de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si su unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo.

• No conecte los cables de altavoz de la unidad entre sí.

Nota sobre la conexión• Si el altavoz y el amplifi cador no están conectados

correctamente, aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión del altavoz y el amplifi cador.

• No es posible conectar otro iPod mediante el adaptador XA-110IP.

Connection diagram

1 To a metal surface of the carFirst connect the black ground (earth) lead, then connect the yellow and red power supply leads.

2 To the power antenna (aerial) control lead or power supply lead of antenna (aerial) boosterNotes• It is not necessary to connect this lead if there is no power

antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial).

• When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.”

3 To AMP REMOTE IN of an optional power amplifi erThis connection is only for amplifi ers. Connecting any other system may damage the unit.

4 To the +12 V power terminal which is energized in the accessory position of the ignition switchNotes• If there is no accessory position, connect to the +12 V

power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a

metal surface of the car fi rst.• When your car has a built-in FM/AM antenna (aerial) in

the rear/side glass, see “Notes on the control and power supply leads.”

5 To the +12 V power terminal which is energized at all timesBe sure to connect the black ground (earth) lead to a metal surface of the car fi rst.

Notes on the control and power supply leads• The power antenna (aerial) control lead (blue) supplies +12 V

DC when you turn on the tuner.• When your car has built-in FM/AM antenna (aerial) in the rear/

side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer.

• A power antenna (aerial) without a relay box cannot be used with this unit.

Memory hold connectionWhen the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Notes on speaker connection• Before connecting the speakers, turn the unit off.• Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage.• Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of the left speaker.

• Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.• Connect only passive speakers. Connecting active speakers

(with built-in amplifi ers) to the speaker terminals may damage the unit.

• To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers.

• Do not connect the unit’s speaker leads to each other.

Notes on connection• If speaker and amplifi er are not connected correctly, “FAILURE”

appears in the display. In this case, make sure the speaker and amplifi er are connected correctly.

• The second iPod cannot be connected by using XA-110IP.

Page 8: Cdx Gt61uigt610ui

8

CDX-GT61UI/GT610UI

• CDX-GT610UI

BBUS AUDIO IN

BUS CONTROL IN

BUS AUDIO IN

BUS CONTROL IN

Source selector*Sélecteur de source*

XA-C40

* not supplied non fourni

iPod

iPod Exemple de raccordement Remarques (2-A)• Raccordez d’abord le câble de mise à la masse avant de

raccorder l’amplifi cateur.• L’alarme est émise uniquement lorsque l’amplifi cateur intégré

est utilisé.

Conseil (2-B- )Dans le cas du raccordement de deux changeurs de CD/MD ou plus, le sélecteur de source XA-C40 (non fourni) est requis.

Remarques sur le syntoniseur radio satellite (2 -C)• Cet appareil n’est pas compatible avec le XMDSON100.• Vous ne pouvez pas raccorder plusieurs syntoniseur

radio satellite (XM/SIRIUS) au XA-C40 en même temps.

• Lorsque vous utilisez un syntoniseur radio satellite, veillez à le raccorder à la borne INPUT 1 du XA-C40.

Connection example Notes (2-A)• Be sure to connect the ground (earth) lead before connecting

the amplifi er.• The alarm will only sound if the built-in amplifi er is used.

Tip (2-B- )For connecting two or more CD/MD changers, the source selector XA-C40 (not supplied) is necessary.

Notes on satellite radio tuner (2 -C)• This unit does not support the XMDSON100.• You cannot connect two or more satellite radio tuners

(XM/SIRIUS) to the XA-C40 at the same time. • When you use a satellite radio tuner, be sure to connect

to the INPUT 1 terminal of the XA-C40.

Page 9: Cdx Gt61uigt610ui

9

CDX-GT61UI/GT610UI

L

R

BUS AUDIO IN

AUDIO OUT REAR*2 BUS

CONTROL IN

2

4

5

1

3

AUDIO OUTREAR/SUB

BUSIN

AMP REMMax. supply current 0.3 ACourant max. fourni 0,3 A

Fuse (10 A)Fusible (10 A)

Blue/white stripedRayé bleu/blanc

ANT REM

RedRouge

YellowJaune

BlackNoir

BlueBleu

WhiteBlanc

GreenVert

PurpleViolet

White/black stripedRayé blanc/noir

Gray/black stripedRayé gris/noir

Green/black stripedRayé vert/noir

GrayGris

LeftGauche

RightDroit

LeftGauche

RightDroit

*1 RCA pin cord (not supplied)*2 AUDIO OUT can be switched SUB or

REAR. For details, see the supplied Operating Instructions.

*1 Cordon à broche RCA (non fourni)*2 AUDIO OUT peut être commuté sur SUB

ou REAR. Pour obtenir plus de détails, reportez-vous au mode d’emploi fourni.

Purple/black stripedRayé violet/noir

*1

Source selector(not supplied)

Sélecteur de source(non fourni)

XA-C40

Supplied with the CD/MD changerFourni avec le changeur de CD/MD

Max. supply current 0.1 ACourant max. fourni 0,1 A

from car antenna (aerial) à partir de l’antenne du véhicule

Supplied with XA-C40Fourni avec le XA-C40

2

Schéma de raccordement

1 Vers un point métallique de la voitureBranchez d’abord le câble de mise à la masse noir et, ensuite, les câbles d’alimentation jaune et rouge.

2 Vers le câble de commande d’antenne électrique ou vers le câble d’alimentation de l’amplifi cateur d’antenneRemarques• Il n’est pas nécessaire de raccorder ce câble s’il n’y a pas

d’antenne électrique ni d’amplifi cateur d’antenne, ou avec une antenne télescopique manuelle.

• Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ».

3 Vers AMP REMOTE IN de l’amplifi cateur de puissance en optionCe raccordement s’applique uniquement aux amplifi cateurs. Le branchement de tout autre système risque d’endommager l’appareil.

4 Vers la borne d’alimentation +12 V qui est alimentée quand la clé de contact est sur la position accessoiresRemarques• S’il n’y a pas de position accessoires, raccordez la borne

d’alimentation (batterie) +12 V qui est alimentée en permanence.Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.

• Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ».

5 Vers la borne d’alimentation +12 V qui est alimentée en permanenceRaccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.

Remarques sur les câbles de commande et d’alimentation• Le câble de commande d’antenne électrique (bleu) fournit une

alimentation de + 12 V CC lorsque vous mettez la radio sous tension.

• Lorsque votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, raccordez le câble de commande d’antenne électrique (bleu) ou le câble díalimentation des accessoires (rouge) à la borne d’alimentation de l’amplifi cateur d’antenne existant. Pour plus de détails, consultez votre détaillant.

• Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil.

Raccordement pour la conservation de la mémoireLorsque le câble d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt.

Remarques sur le raccordement des haut-parleurs• Avant de raccorder les haut-parleurs, mettez l’appareil hors

tension.• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms

avec une capacité électrique adéquate pour éviter de les endommager.

• Ne raccordez pas les bornes du système de haut-parleurs au châssis de la voiture et ne raccordez pas les bornes du haut-parleur droit à celles du haut-parleur gauche.

• Ne raccordez pas le câble de mise à la masse de cet appareil à la borne négative (–) du haut-parleur.

• N’essayez pas de raccorder les haut-parleurs en parallèle.• Raccordez uniquement des haut-parleurs passifs. Le

raccordement de haut-parleurs actifs (avec amplifi cateurs intégrés) aux bornes des haut-parleurs peut endommager l’appareil.

• Pour éviter tout problème de fonctionnement, n’utilisez pas les câbles des haut-parleurs intégrés installés dans votre voiture si l’appareil possède un câble négatif commun (–) pour les haut-parleurs droit et gauche.

• Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil.

Remarques sur le raccordement• Si les haut-parleurs et l’amplifi cateur ne sont pas raccordés

correctement, le message « FAILURE » s’affi che. Dans ce cas, assurez-vous que les haut-parleurs et l’amplifi cateur sont bien raccordés.

• Il est impossible de raccorder un autre iPod à l’aide du XA-110IP.

Connection diagram

1 To a metal surface of the carFirst connect the black ground (earth) lead, then connect the yellow and red power supply leads.

2 To the power antenna (aerial) control lead or power supply lead of antenna (aerial) boosterNotes• It is not necessary to connect this lead if there is no power

antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial).

• When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.”

3 To AMP REMOTE IN of an optional power amplifi erThis connection is only for amplifi ers. Connecting any other system may damage the unit.

4 To the +12 V power terminal which is energized in the accessory position of the ignition switchNotes• If there is no accessory position, connect to the +12 V

power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a

metal surface of the car fi rst.• When your car has a built-in FM/AM antenna (aerial) in

the rear/side glass, see “Notes on the control and power supply leads.”

5 To the +12 V power terminal which is energized at all timesBe sure to connect the black ground (earth) lead to a metal surface of the car fi rst.

Notes on the control and power supply leads• The power antenna (aerial) control lead (blue) supplies +12 V

DC when you turn on the tuner.• When your car has built-in FM/AM antenna (aerial) in the rear/

side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer.

• A power antenna (aerial) without a relay box cannot be used with this unit.

Memory hold connectionWhen the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Notes on speaker connection• Before connecting the speakers, turn the unit off.• Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage.• Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of the left speaker.

• Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.• Connect only passive speakers. Connecting active speakers

(with built-in amplifi ers) to the speaker terminals may damage the unit.

• To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers.

• Do not connect the unit’s speaker leads to each other.

Notes on connection• If speaker and amplifi er are not connected correctly, “FAILURE”

appears in the display. In this case, make sure the speaker and amplifi er are connected correctly.

• An another iPod cannot be connected using the XA-110IP.

Page 10: Cdx Gt61uigt610ui

10

CDX-GT61UI/GT610UISECTION 3

DISASSEMBLY

Note: This set can be disassemble according to the following sequence.

3-1. SUB PANEL (FL-U) ASSY(Page 11)

3-2. CD MECHANISM BLOCK(Page 11)

SET

3-3. MAIN BOARD(Page 12)

3-5. CHASSIS (T) SUB ASSY(Page 13)

3-6. ROLLER ARM ASSY(Page 13)

3-7. CHASSIS (OP) ASSY(Page 14)

3-4. SERVO BOARD(Page 12)

1. CHUCKING ARM SUB ASSY(SUPPLEMENT-1 Page 1)

2. SLED MOTOR ASSY(SUPPLEMENT-1 Page 2)

3. OPTICAL PICK-UP SECTION(SUPPLEMENT-1 Page 3)

4. OPTICAL PICK-UP(SUPPLEMENT-1 Page 3)

Ver. 1.1

Page 11: Cdx Gt61uigt610ui

11

CDX-GT61UI/GT610UI

3-2. CD MECHANISM BLOCK

Note: Follow the disassembly procedure in the numerical order given.

3-1. SUB PANEL (FL-U) ASSY

2 two claws

3 two claws

4 sub panel (FL-U) assy

1 two screws (+PTT 2.6 × 6)

4 CN350

5 CN352 (3P)

3

1 screw(+PTT 2.6 × 6)

2 screw(+PTT 2.6 × 6)

6 two screws(+PTT 2.6 × 4)

7 bracket (CD)8 CD mechanism block

Page 12: Cdx Gt61uigt610ui

12

CDX-GT61UI/GT610UI

3-4. SERVO BOARD

3-3. MAIN BOARD

qf MAIN board

insulating sheet

3

2 two screws(+PTT 2.6 × 8)

6 screw(+PTT 2.6 × 8)

qs screw(+PTT 2.6 × 10)

qa screw(+P 2.6 × 10)

qd heat sink

9 two screws(+P 2.6 × 8)

8 screw(+PTT 2.6 × 10)

0 two screws(+PTT 2.6 × 10)

1 three ground point screws (+PTT 2.6 × 6)

7 connection cord4 CN250 (7P)

5 CN200 (3P)

5 SERVO board

SERVO board

claw

claw

3 toothed lock screw(M 1.7 × 2.5)

2 toothed lock screw(M 1.7 × 2.5)

1 Remove the eleven solders.

GRYYELBLU

ORGREDBLKREDWHT

BLKREDWHT

4 optical pick-up (16 core)(CN1)

Page 13: Cdx Gt61uigt610ui

13

CDX-GT61UI/GT610UI

3-6. ROLLER ARM ASSY

3-5. CHASSIS (T) SUB ASSY

4 chassis (T) sub assy

3 claw

1 two precision screws(+P 1.7 × 2.2)

2 two precision screws(+P 1.7 × 2.2)

3 washer

4 gear (RA1)

5 roller arm assy

1 spring (RAL)

2 spring (RAR)

Page 14: Cdx Gt61uigt610ui

14

CDX-GT61UI/GT610UI

3-7. CHASSIS (OP) ASSY

7 coil spring (damper) (natural)

8 coil spring (damper) (green)

6 chassis (OP) assy

5

1 tension spring (KF)

2 gear (LE1)

3 lever (D)

4 slider (R)

Ver. 1.1

Page 15: Cdx Gt61uigt610ui

15

CDX-GT61UI/GT610UISECTION 4

DIAGNOSIS FUNCTION

Description of the Diagnostics function:

1. Setting the Diag display modeWith the power off, press the [4] button, [5] button, and [4] buttonon the set body or the remote control (for more than 2 seconds)in turn.

2. Canceling the Diag display modeDuring the Diag function mode, press the [OFF] button.

3. Initial display in the Diag display mode.Just when the Diag mode is entered, “reset count” is displayed.The display mode is switched by each rotation of M >/SEEK + or . m/SEEK – keys.

4. Contents of each display mode4-1. Reset count display mode

4-2. Reset count by watchdog timer display mode

4-3. Number of connected units display mode

The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the number of connected units displaymode.

4-4. Operating hours display mode

Reset count (in hexadecimal format)

Diag code01: Reset count

0 1 X X

Reset count (in hexadecimal format)

Diag code 02: Number of resets by watchdog timer

0 2 X X

Show the number of connected units for CD-C, MD-C and XM respectively from the rightmost (in hexadecimal format).

Recency of information1-3: 1 represents the latest.

Diag code03: Number of connected unit.

0 3 1 X X X

No. of connected units history 1 (latest) display

No. of connected units history 3 display

No. of connected units history 2 display

0 3 1 X X X

0 3 2 X X X

0 3 3 X X X

Operating hours (in hexadecimal format)

Diag code04: Operating hours

0 4 X X X X

Reset count display

OFFSET/FAILURE error display

CD error information display

Operating hours display

Number of connected units display

Reset count by watchdog timer display

0 1 X X

0 2 X X

0 3 1 X X X

0 4 X X X X

0 5 1 X X

0 6 1 X X X X X

USB error information display

0 7 1 X X

Page 16: Cdx Gt61uigt610ui

16

CDX-GT61UI/GT610UI

4-5. CD error information display mode4-5-1. Error description

4-5-2. Operating hours

The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the CD error information display mode.

4-6. OFFSET/FAILURE error display mode

The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the OFFSET/FAILURE error displaymode.

Error description (in hexadecimal format)

Recency of information1-3: 1 represents the latest.

Diag code05: CD error information

0 5 1 X X

Operating hours

Recency of information1-3: 1 represents the latest.

Diag code05: CD error information

0 5 1 X X X X

CD error info history 1 (latest)Error description plus error details display

CD error info history 3Disc type plus operating hours display

CD error info history 3Error description plus error details display

CD error info history 2Disc type plus operating hours display

CD error info history 2Error description plus error details display

CD error info history 1 (latest)Disc type plus operating hours display

0 5 1 X X X X

0 5 2 X X

0 5 2 X X X X

0 5 3 X X

0 5 3 X X X X

0 5 1 X X

Operating hours

Recency of information1-3: 1 represents the latest.

Diag code06: OFFSET/FAILURE

Error description (0: OFFSET, 1: FAILURE)

0 6 1 X X X X X

OFFSET/FAILURE error history 1 (latest) display

OFFSET/FAILURE error history 3 display

OFFSET/FAILURE error history 2 display

0 6 2 X X X X X

0 6 3 X X X X X

0 6 1 X X X X X

Error informationIndication Description

1X SERVO ERROR3X LOADING ERROR4X TRACK JUMP5X TEXT ERRORFX MECHA ERROR

4-7. USB error information display mode4-7-1. Error description

Error description (in hexadecimal format)

Recency of information1-5: 1 represents the latest.

Diag code07: USB error information

0 7 1 X X

Error informationIndication Description

15 DEVICE ERROR

17FILE ERROR(NO MUSIC)

1E POWER ON ERROR1F BOOT ERROR

3AINVALID EJECTERROR

43 READ ERROR

44INVALIDFORMAT FILE

FANOT SUPPORTDEVICE

FBHUB NOTSUPPORT

Page 17: Cdx Gt61uigt610ui

17

CDX-GT61UI/GT610UI

4-7-2. Disc type and operating hours The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the CD error information display mode.

USB error info history 1 (latest)Error description plus error details display

USB error info history 3Disc type plus operating hours display

USB error info history 3Error description plus error details display

USB error info history 2Disc type plus operating hours display

USB error info history 2Error description plus error details display

USB error info history 1 (latest)Disc type plus operating hours display

0 7 1 X X X X

0 7 2 X X

0 7 2 X X X X

0 7 3 X X

0 7 3 X X X X

0 7 1 X X

USB error info history 5Disc type plus operating hours display

USB error info history 5Error description plus error details display

USB error info history 4Disc type plus operating hours display

USB error info history 4Error description plus error details display

0 7 4 X X

0 7 4 X X X X

0 7 5 X X

0 7 5 X X X X

Operating hours

Recency of information1-5: 1 represents the latest.

Diag code07: USB error information

0 7 1 X X X X

Page 18: Cdx Gt61uigt610ui

18

CDX-GT61UI/GT610UI

MEMO

Page 19: Cdx Gt61uigt610ui

19 19CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

5-1. BLOCK DIAGRAM — MAIN SECTION —

SECTION 5DIAGRAMS

• Signal Path• R-CH is omitted due to same as L-CH.

: CD PLAY

: FM

: BUS

: AM

: IPOD

: AUX

J901

AUX

AUX R-CH

1 ANT

SCLSDA

CDMONCDON

9 AUX-LCH

ELECTRONIC VOLUMEIC401

IPOD/BUS SELECTSWITCHIC402

J1(ANTENNA)

TU1(TUNER UNIT)

I2C BUS CONTROLLED POWER AMP/MULTIPLE VOLTAGE REGULATOR

IC300

SYSTEM CONTROLIC501 (1/2)

CN300

7 AUX-RCH

BATT

6 CD-LCH5 CD-RCH

6S-METER7TUN MUTE

16E2P SCL17E2P SDA

39 VSM

5QUALITY 38 QUALITY

95 CDMON94 CDON61 Z MUTE

11VDD+5V

4L-CH3R-CH

BU+3.3V

10VCC

12 TUATT

25 EEP CKO24 EEP SIO

CD ONCDM ON

CD LCD R

4 TU-LCH3 TU-RCH

CD-RCH

A ATT

R-CH(REAR)

TU-RCH

AUDIO+8.3V

AUDIO+8.3V

24OUT-RRR-CH(FRONT)26OUT-FR

53

OUT FL+OUT FL–

97

OUT RL+OUT RL–

2927

AMP REM

R-CH

ANT REM

BATT

3037

AUDIO+B

35VP20VP16VP2

BU+B3133

SERVO3.3VMECHA6V

34PANEL+B

28MUTE

2 SDA

AUDIO+8.3VBU+5VSERVO+3.3VMECHA+6VPANEL+B

4 SCL

SDASCL

16 BEEP22 STB25 DIAG

15

7

10

12

11

16

19

2

4

3

56

2930

SCLSDA

SCLSDA

SCLSDA

9VOLATT

100ATT

33I2C SCK34I2C SIO

96

BUIN

97TESTIN

12 IN FL FL+FL–

RL+RL–

FR+FR–RR+RR–

AMP-REMANT-REM

ACC

TEST

11 IN RL23OUT-RL

25OUT-FL

MUTEQ432

AUDIO OUTREAR

MUTE CONTROLSWITCH

Q491,492

60

UNISI54

UNISO

58

UNISCK

59

BUSON

88SYSRST

12

B/U-C11

DATA OUT10

DATA IN8

CLK IN

9

BUS IN

13 RST

RESET

3

56

8

423

1

BATT

CLK 4DATA I/O

1BUS ON

2RST

SYSR

ST

99ACC IN ACCESSORY CHECKQ702

BATTBATT

BATTERYCHECKQ605

BUS INTERFACEIC601

MUTEQ470

MUTEQ401

MUTE CONTROLSWITCH

Q411,412

MUTEQ440

D491

F901

R-CH2122

SUBOUT-LSUBOUT-R

R-CH

L

R

J652 (2/2)

BUSCONTROL IN

D353

D602

DISPLAY SECTIONB

IPOD-AUD-LDISPLAY SECTION A

BUIN

SYSRST

UNI SIUNI SO2UNI CLK

DISPLAY SECTIONC

TH400

CNJ4007

BATT

TUNER+5VREGQ3

15E2PVDD

13TU-SCL14TU-SDA

BU+5VBU+3.3V

REGIC681

5DIAG8AMPSTB

7BEEP

D609

D251

BUSAUDIO

IN BUS-RCH

L

R

J652 (1/2)

2 BUS-LCH

BUS-RCH,IPOD-AUD-RCH

CD-RCH

AUX-RCH

TU-RCH

1 BUS-RCH

11 10

8 9

126

ZMUTE

93 WAKE UPWAKE UP

27 MC RX

73 FUNC SEL

MC RX

28 MC TXMC TX

Z MUTE

SYS RST

MECHA+6VBU+3.3V

SERVO+3.3V

B/U CHECK

RXD

TXD

DR+6V

BU+3.3V

A+3.3V

D+3.3V

CDONCDMONZMUTE

WAKE UP WAKE UP

SYSRST

BUIN

MC TX

MC RX

CDMECHANISM

UNIT(MG-101U)

(1/2)

6

UNI S

O2

UNI C

LK

UNI S

I

BU IN

FUNCTION SELECTCONTROL SWITCH

Q413

(Page 20)

(Page 20)

(Page 20)

Page 20: Cdx Gt61uigt610ui

2020CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

5-2. BLOCK DIAGRAM — DISPLAY SECTION —

RESETMAIN

SECTION B

IPOD-AUD-L MAIN SECTIONA

MAIN SECTIONC

KEY ACKNOWLEDGESWITCH

Q664

83

82

41

192018

40

52

48

64

SYSTEM CONTROLIC501 (2/2)

USB OVERCURRENT

PROTECTORIC804

DC-DC CONVERTERIC803

SHIFTCONTROLSWITCH

Q805

FL901FLUORESCENT

INDICATOR TUBE

KEYIN0

CLKCS

FL SOFL SCK

FL CS

20

19

16

GRID1

GRID2

GRID3

411G

15RESET

F+

F–

5VDD(+3.3V)

KEYIN1

31 RE-IN032 RE-IN1

KEYACK

AD ON

62 NOSESW

SIRCS

77 RESET

16 OC2BATT

R-CH

(IPOD IN) BUIN42AIN0/INT2

11INT0

IPOD-AUD-L

IPOD-AUD-R

IPOD-CHANGE

IPOD-TX+5V

IPOD-RX+5V

IPOD+3.3V

UNI SI1MOSI

UNI SO22MISO

UNI CLK3SCK

SYSRST4RESET

41T1

8XTAL1

7XTAL2

14 OC1A

9 RXD

10 TXD

12 INT1

FL VH+12V

OSCOUT

OSCIN

89FL ON

X50118.432MHz

1214

10

3G

D503

17 •

18

6 •

42

1•2

44•

45

2GDIO

PANEL+B

BU+3.3V

KEY MATRIX

80

79

XOUT

XIN

X50232.768kHz

X2507.3728kHz

10FSW IN

91USB OVER

74BUSON A

92USB ON

90DD ON

75FSW OUT

LSW901,902S901–904,906–915

(VOLUME)

PUSH SELECTRE901

ROTARYENCODER

MUTE CONTROLSWITCH

Q200

IPOD TX+5VCONTROL SWITCH

Q252,253

IPOD RX+5VCONTROL SWITCH

Q254,255

IPOD CHARGECONTROL SWITCH

Q250,251

MUTEQ210

GND ISOLATIONIC200

IPODAUDIO AMP

IC201

IPOD ADAPTORIC250

BUFFERQ256,257

REMOTE CONTROLSIGNAL RECEIVER

IC971

RESETIC602

PANEL+B

FL VH+12V

BATT

PANEL+B

LED841–847,850–857,961–963,LSW901,902

INOUT

USB D–USB D+

4 /EN5 /OC

1

7

65

3

22•3

6•7•8

FL DRIVEQ883

FL DRIVEQ882

FL DRIVEQ881

PANEL+B

9VH

FL VDD+3.3VREG

IC972

FL+3VREG

IC802

S103RESET

D804

D250

D255

FL +12VREG

IC801

SW

BATT

INV

FB

VIN

EN

RT

D801

1 CN902

(USB)

CN902

CDMECHANISM

UNIT(MG-101U)

(2/2)

234

5 7IN2 OUT2

BUS ON/OFFSWITCH

Q258

• Signal Path• R-CH is omitted due to same as L-CH.

: IPOD

(Page 19)

(Page 19)

(Page 19)

Page 21: Cdx Gt61uigt610ui

21 21CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

• WAVEFORMS

— MAIN Board —

• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note isprinted in each block.)

For schematic diagrams.Note:• All capacitors are in µF unless otherwise noted. (p: pF)

50 WV or less are not indicated except for electrolyticsand tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

specified.• f : internal component.• C : panel designation.

For printed wiring boards.Note:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• a : Through hole.• : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)

• A : B+ Line.• B : B– Line.• H : adjustment for repair.• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions. no mark : FM

( ) : AM< > : CD PLAY

∗ : Impossible to measure• Voltages are taken with a VOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal productiontolerances.

• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal productiontolerances.

• Circled numbers refer to waveforms.• Signal path.J : CD PLAYF : FMf : AML : BUSg : AUXc : IPOD

Caution:Pattern face side: Parts on the pattern face side seen from the(Side B) pattern face are indicated.Parts face side: Parts on the parts face side seen from the(Side A) parts face are indicated.

Q

C

These are omitted

EB

EThese are omitted

CB

CThese are omitted

BE

Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.

0.7 Vp-p

7.3728 MHz

3 IC250 8 (XTAL1)

0.7 Vp-p

32.768 kHz

1 IC501 i; (XOUT)

1 Vp-p

18.432 MHz

2 IC501 is (OSC IN)

0.2 V/DIV, 20 µsec/DIV

0.2 V/DIV, 0.1 µsec/DIV

0.5 V/DIV, 0.1 µsec/DIV

Page 22: Cdx Gt61uigt610ui

2222CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

: Uses unleaded solder.5-3. PRINTED WIRING BOARD — MAIN SECTION —

1

A

B

C

D

E

F

G

H

I

2345678910111213

C15

IC602

R55

8

C504

R462

R442

R60

1D2

C307

R355

C330 C305C301

C304

C424

C444

C325

C312

C302

C320

C315

C454 C4

34

R250

C256

Q3

R42

0 R41

3

C681

IC681

L902

Q42

0

R423

R443

Q460Q470

R421

R44

0

C443

L804

C309

C462

L901 R472

R47

1

R463

R47

3

C426

C472

C601

R607

D605

C329

R61

2R

615

R26

5R

266

Q41

2R26

7

R268

D901

IC601

R25

6

R709

R257

R259

R260

C254

C902

L4

R261

D603

R262

R263

R264

R572

C255R

270

C251

C252

R251 C250

C515

D609

C516

R706

R25

2

R25

4

R70

7

R275

R708R

276

Q702

R27

4

R277

R278

R27

9

R284R285

R28

6

R25

3

R255

R491

Q491

Q49

2

C8C3

R6R7

R12R13

D604

R2R3

R4R5

R9

R10

C6

C7

C513

C501C512

C514

C502

C509

C510

D251

Q41

1

L1

IC401

L501

Q413

C253

D602

R35

1

L405L410

L402

IC402

L403

L407

L406

Q200

Q210 Q220

C415

C493

R401

R402

C418

C419

C412C4

17

C402

L250

IC803

C891

D80

2

C890

R820

R819C814

R800R815

(CHASSIS)

D80

1

R813

R81

4

R818C812

R81

7

R816

C901

C682

R60

0

C507

C508

C519

D35

3

R56

3R636

R485

C318C319

R301

R30

2

R47

0

C704

C705

C317

R35

7

R45

2

R49

9

L401

R43

0

R46

0

C494

R35

8

R356

C484

R606 R46

1

R447R448

Q44

0

IC250

C423

C445

C463

C473

R60

2

L409

Q252

Q253

Q254

Q255

Q257

Q256

Q60

5

R540

R526

R925R592R593

R50

9

R91

0

R92

4

Q80

5

R50

7R

538

R55

1

R544

R557

R536

R552

R53

4

R560

R556 R914R915

R916R511R510

R523

R520

R59

5 R59

6

R522

R521

R502R503

R50

4R

505

R673R567

R56

1R

517

R59

7R59

8

R529

R570R519

R674

R553R568

R532R533R569

R201R202 R203

Q664R565

R531

R291

D70

6

D70

7

D50

2

D503

D491D703

D702

D606

R604R603

IC501

R59

9(CHASSIS)

(CHASSIS)

1-872-968- 11

17 8

14

1 16

1732

123

4

1 7

D2 F-2(D101) H-4(D102) H-4(D103) H-4(D104) H-4(D105) I-4(D106) H-3(D107) H-3(D108) H-3(D109) H-3(D110) H-4(D111) H-3(D112) H-4(D113) H-3(D153) H-3(D156) H-2(D250) F-9D251 F-7(D252) F-9(D253) G-9(D254) F-9(D255) D-9(D301) C-5(D302) C-5(D303) D-6(D304) C-6(D305) C-5(D306) C-6(D307) C-6(D308) C-6(D309) C-6(D310) C-6(D311) C-7(D312) C-7D353 F-7D491 C-7D502 F-6D503 G-5D602 D-9D603 D-9D604 C-9D605 C-9D606 C-9(D607) C-9D609 D-9D702 D-8D703 C-8D706 C-7D707 C-7D801 H-9

• Semiconductor LocationRef. No. Location Ref. No. Location

D802 H-8(D804) H-7D901 B-9

(IC200) F-3(IC201) F-3IC250 E-9(IC300) B-6IC401 D-3IC402 D-2IC501 G-6IC601 D-9IC602 E-5IC681 E-5(IC801) G-8(IC802) H-8IC803 G-8(IC804) H-6

Q3 E-2Q200 E-3Q210 E-3Q220 E-3(Q250) D-9(Q251) E-9Q252 E-10Q253 E-10Q254 F-10Q255 F-10Q256 E-9Q257 F-9(Q258) E-9(Q401) E-6(Q402) E-6Q411 E-7Q412 E-7Q413 D-2Q420 B-4(Q432) B-3Q440 B-4(Q452) B-3Q460 C-4Q470 C-4Q491 D-7Q492 D-7Q605 D-9Q664 G-5Q702 D-8Q805 H-8

( ): SIDE B

Page 23: Cdx Gt61uigt610ui

23 23CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

(Page 28)

1

A

B

C

D

E

F

G

H

I

2 3 4 5 6 7 8 9 10 11 12 13

1-872-968- 11

C998

C914

C822

R451

C452

Q432

D105

R431

Q452

R810

R902R903

R281

R283

R280

R282

1

7

D253

C260

D252C259

C261

D25

4

R287

Q250

Q251

R27

1

R273

C257

D10

1D

102

R403Q401

Q402

R404

D15

2

D151

D156C154C155

R151

C157

L151

R15

2

R153 R154

R15

0

R156D10

6D

107

D10

9

D108 D11

3

D153

D11

1

R821

D110

D112

R210

R220

C210C220

IC200

IC201

C201 R200

R211

R221

R212

R222

C205

C203

C213

R21

6

C223R226

R214

R21

5

R15

5R

224

R225

R45

0

R21

7

R227

R21

9R218R228

R22

9

C362

C413

IC80

1

R809

C804

C802

C808

C810

C816

IC804

R811

IC80

2R812

C805

C807

R80

2R

803C8

20D255

R288

CN2

CDMECHANISM

UNIT(MG-101U)

CN101

Q258

L805

D10

3

D10

4

R95

2

D804

R95

1

C913

C361

R204

C414

R449C432

C823

R290

R289

R272

R293

R294R295

L251

D250

R292

TU1(TUNER UNIT)

L818

C622

R70

5

S103

S103RESET

C600

X501

X502

D30

2

D30

1

D303

D304

D30

5

D30

6D

307

D30

8

D30

9

D31

0

D31

1

D31

2C303

X250

J652

(IPOT IN)

C702C491

C701

YEL

C2

C5

CN370

C153

C151

CN200

C211

C207

C221

C200

C206

C222

C212

C204

CN350

C214

CNJ400

CNJ400(BUS CONTROL IN)

C224

C405

C202

TH400

C401

C623

C367

C368

L802

C803

C809

L803C811C817

C806

L300

CN352

D607

C152

C403

C366

C365

CN300

C451

C471

C431

C461

C441C4

21

C485

C683

IC300

C258

C406

C407

C409

C308

C486

C363

C364

C314

C316

C306

C225 C2

15

C624

C818

YEL

L RJ1

(ANTENNA) L R

-1 -2 -3 -4

AUDIO OUTREAR

X501

8 73 2 1

6 5 4

BUSAUDIO IN

1

1

5

5

F901

CN250

Page 24: Cdx Gt61uigt610ui

2424CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

(Page 26)

(Page 25)

(Page 27)

5-4. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 30 for IC Block Diagrams.

IC B/D

IC B/D

C622

R604

C306

R607

R603

R709

D609

C702R706 R708

R491

C491

Q491

Q492

C623

R600

D607

R302

D60

6

C624

R531

D30

1

D30

2

D30

3

D30

4

D30

5

D30

6

D30

7

D30

8

D30

9

D31

0

D31

1

D31

2

C329

C601

C705

C704

L300

R705

C302

C317

C325

C301

C444

C319

C434C454

C424

C330

C304 C305 C307

C312

C682

C309

CNJ400

TH400

C600R606

R612R602

R601

CN300

C701

R707

C901 C902

C315C314C316

C320

L501 C683

C681

C308

L901

L902

C303

R301

C318

IC602IC681

F901

R615

Q702

Q605

D703

D70

2

D706 D707

D60

5

D60

4

D901

D603

D602

IC601

D491

IC300

Page 25: Cdx Gt61uigt610ui

25 25CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

5-5. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 30 for IC Block Diagrams.

(Page 27)

(Page 24)

IC B/D

IC B/D

R442 R451

R355

Q432

Q3

R420

R413

Q420

R431

Q452R423

R443

Q46

0Q

470

R421

R440

R471

Q412

R201

R12 R13

C485

R2R3

R10

R403

Q411

R404

L1

CN200

C206

R200

R221

R212

R222

C222

C212 R203

R202

R216

R226

R214

R215

R224R225

R450

C214

C225

R217

C224

R227

Q210 Q220R219

R218 R228

R229

R470

R357

R452

R499

R430

R460

R358

R356

R204

C366C365

C451

R461

R449R447R448

C471

C431

Q440

C461

C441C421

R485

C914

C473 C472

C463 C462

C426 C423

C445 C443

C484

C201

R210

R220C220

C210

C493

C494

C452 C432 C413 C414

C362

C361

C6

C7

J1

R4

R6 R7L4

C5

R558

C486

C223C213

C215

C202C203

C204C205

C200

R211

C367C368

C364

C363

C221

C211

R473

R463

R462

R472

C15

Q200

J652

Q413

Q402

Q401

TU1

C8C3C2

R9

R5

C207

IC402

IC401

C998

D2

IC201

IC200

(Page 27)(Page 26)

Page 26: Cdx Gt61uigt610ui

2626CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

5-6. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) —• Refer to page 21 for Waveforms.• Refer to page 33 for IC Pin Description of IC501.

(Page 24)

R523

R55

7

R51

0

R572

R55

6

R51

1

R502

R521

R503

R50

4

R561

R565 R567

R59

7

R517

R59

6R522

R59

8

R53

2

R526

R925

R592

R593

C407

C406

R50

5

R673

CN350

R56

8

R351

L410

L402

L403

L407

C409

R401

R402

R519

R53

3

D353

R563

R636

R55

3

L401

R599

C415

C412

C419

C402

C508

C510

C507

C519

C509

C504

C516C515

C513

C501

C512

C502

C514

R902

R903

L405

L406

C417

C405

C418

C403

C401

L409

D50

2

R52

9

R57

0

R674

R924

R540

R509

R910

R534

R53

6

R54

4

R56

0

R91

4

R91

5

R91

6

R520

R59

5

X501

X502

R53

8

R50

7

R55

1

R55

2

Q664

D251

R569

S103

IC501

D503

(Page 27)

(Page 25)

Page 27: Cdx Gt61uigt610ui

27 27CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

5-7. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) —• Refer to page 21 for Waveforms.• Refer to page 31 for IC Block Diagrams.

(Page 25)

(Page 24)

(Page 25)

IC B/D

IC B/D IC B/D

IC B/D

R250

R810

R26

5R

266

R26

7R

268

R256R257

R261R262

R263R264

R251

D250

R275

R276

Q252

Q253

Q254

Q255

R274

R277

R278

R279

Q256

Q257

R284

R285

R286

R253

R281

R280

R287

Q250

Q251

C258

R153

R154

R821

L250

L802

C803

R809

C891

Q805

R813

R811

R812

C806

D255R288

C152

R289

R816

R817

IC804

L803

R273

C257

C253

C255

C256

C251

R290

R291

C261

C260

C259

C804

C805 C807

C154

R156

C823

CN352

C822

L818

C820

L805C818

L804

C157

C155R152

C151

L151

R151

R150

C254

R260R259

R255

R254

R252

C252X250

C250

R270

R292

L251

R271

R272R295R294R293

C809C808

C890R814

R800 R815

C812

R818 C810

C811

C816

C817 R802 R803

R820 R819

C814

C802

D804

R951

R952

C153

R155

Q258

CN370

D80

1

D80

2

IC250

D102 D101

D104 D103

D156 D151 D152

D106

D107

D109

D108

D113D153D111

D112

D110

D105

CN250

R282

R283

D25

4

D25

3

D25

2

IC801 IC802

IC803 (Page 29)

(Page 26)

Page 28: Cdx Gt61uigt610ui

2828CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

5-8. PRINTED WIRING BOARD — KEY SECTION — : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

I

2 3 4 5 6 7 8 9 10 11 12 13

AMAIN BOARD CN370

LED843

LED961

LED961-963(RING ILLUMINATION)

LED

846

LED

847

R904 LED842

LED842(CD INDICATOR)

LED

850 LE

D85

1

LED

852LE

D84

5

S908 S909

S903

LED

853

LED

854S907

LED

856

LED

857

LED841

R909

LED963

LED9

62

IC971S906

S904

S902

S910 R85

4

R947

R96

1

R84

3

R906R907 R908

R90

2

R903

C974 R977

R853

LSW902

S915

LSW901

LED

844

S901

S911 S912 S913 S914LED

855

R96

2R

963

R965

R96

4

C841

C842

C843

R98

9

C981

R98

8

C982

R90

1 C975

D906 D95

3D90

4

D903

R971R

888

R88

9

R887

C976

R978

R98

4R

983

C979

R850

R91

0

CN901

Q882Q881 Q883

R911

FB90

7

FB906

R84

9

R85

1

R912

R85

2

R914

R915

R948 R846

R84

5

R84

4R905

D971 R97

6

R975R922R921

D907R

913

C977

R98

2

R842

R841

R981

D90

5

D90

8

FB904FB905

R99

3

R994R995

C904

LF901

D95

1

D95

5

R881 R882

R88

6

R883R885R884

IC97

2

C905

BRN

RED

ORG

RB901

R859

R86

0

R855R856

R857

R97

4

D90

9 FL901FLUORESCENT

INDICATORTUBE CN

902

CN902

RE901

OFF

LED843,S902

EQ3

LED844,S904

. m

SEEK–

LSW902

BTMLED845

BTM/CATS906

M >

SEEK+

LSW901

SOURCELED846,S903

IC971 LED855,S913S912S911S908DSPL/DIM 3/REP

LED847,S907

MODE

DSPLLED850 LED853

3LED854

4

1/GP/ALBM–S909

LED8511

2/GP/ALBM+S910

LED8522

54/SHUFLED857,S915

SCRLS914

LED8566

6/PAUSE

LED841,S901Z

1-872-032- (21)

21

1-872-033-(21)

21

PUSH SELECT(VOLUME)

RE901

1 2

5 4 3

1-872-032- (21)

21

ORG

REG

BRN

1-872-033- (21)

21

AUXJ901

FB90

3FB

901

FB90

2

1

2

4

3

24

23

2

1

2038424445

42 1

1

4 (USB)

(Page 23)

LED841 A-12LED842 A-7LED843 A-1LED844 B-2LED845 C-2LED846 B-4LED847 C-4LED850 C-5LED851 C-6LED852 C-7LED853 C-7

Ref. No. Location

D903 H-10D904 H-9D905 H-10D906 H-10D907 H-10D908 H-8D909 H-5D971 G-4

IC971 C-4IC972 H-11

• Semiconductor LocationRef. No. Location

LED854 C-8LED855 C-9LED856 C-10LED857 C-11LED961 B-3LED962 C-3LED963 C-2

Q881 H-8Q882 H-8Q883 H-9

Ref. No. Location

Page 29: Cdx Gt61uigt610ui

29 29CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

5-9. SCHEMATIC DIAGRAM — KEY SECTION —

(Page 27)

R901 R904

R888

R889

R887

R978

R984

R983

R909 R910

Q882

Q881

Q883

R911 R912 R914 R915R906 R907 R908

R902 R903

R977

R913

R982

R881

R886

R883

R885

R884

IC972

D904

D908

D906

D907

D905

R974

R975

R976

D97

1R844

R850

R852

R854R860

R964

R965

R855

R856 R961

R857

R962

R963

R842 R845

R846

R841 R843 R849 R851 R853R859

FB901FB903

FB902J901

FB905

FB904

LF901C905

S901

S902

S903

S904

LSW

901(

2/2)

LSW

902(

2/2)

S907

S908

S909

S910

S911

S912

S913

S914

S915

S906

R922 R921

C841

C843

LSW901(1/2)

LSW902(1/2)

C974

C979

C977

C976

C975

C904

C982

C981

FB90

6FB

907

D909

RB9

01

D903

R971

R905

C842

R99

5

R99

4

R99

3

R88

2

R988 R989

CN902

CN901

IC971

FL901

RE901

LED842 LED841

LED843

LED844

LED845

LED846

LED847

LED850

LED851

LED852

LED853

LED854

LED855

LED857

LED856

LED962

LED963

LED961

R981

D95

5D

951

D95

3

R947

R948

Page 30: Cdx Gt61uigt610ui

3030CDX-GT61UI/GT610UI

CDX-GT61UI/GT610UI

• IC BLOCK DIAGRAMS

IC300 TDA8588AJ/N2/R1 (MAIN Board (1/4))

MUT

EM

UTE

ENABLELOGIC

STANDBY/MUTE

BATTERYDETECTION

CHIP DETECT/DIAGNOSTIC

PROTECTION/DIAGNOSTIC

SWITCH

REGU

LATO

R

SWITCH

REFERENCEVOLTAGE

LOADDUMPPROTECTION

TEMPERATUREPROTECTION

BACK-UPSWITCHREGULATOR

1

3

5

7

9

11

13

15

17

19

21

23

25

27

29

31

33

35

37

2

4

6

8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

TAB

OUT-FL–

OUT-FL+

OUT-RL–

OUT-RL+

IN-RL

S-GND

IN-RR

OUT-RR+

OUT-RR–

OUT-FR+

OUT-FR–

DIAG

ANT-REM

AMP-REM

SERVO3.3V

MECH6V

VP

BU+B

SDA

SCL

VP2

PGND1

SVR

IN-FL

IN-FR

BEEP

PGND3

VP1

STB

PGND4

RST

CRES

AUDIO+B

GND

PANEL+B

CBU

FL

RL

RR

VP

FR

I2C BUS

IC601 BA8271F-E2 (MAIN Board (1/4))

1

2

3

456

7 8

9

10

14

131211

BUS ONSWITCH

RESETSWITCH

BATTERYSWITCH

BUS ON

RST

BATT

CLKVREF

GND

VCC

RSTBUS INCLK INB/U–C

DATA IN

DATA OUT

DATA I/O

IC401 BD3442FS-E2 (MAIN Board (2/4))

1

2

BUS-RCH

100k

100k

100k

100k

100k

100k

250k

250k

250k

BUS-LCH

TU-RCH 3

4TU-LCH

5CD-RCH

6CD-LCH

7AUX-RCH

8AUX-GND

9AUX-LCH

10DS3-L

11DS1-L

12DS2-L

13EBIAS

14DS2-R

15DS1-R

16DS3-R

26 OUT-FR

27 VCCVCC

VCC2

28 MUTE

29 SCL

30 SDA

31 GND

32 FIL

INPUTSELECTOR

VOLUME1/MUTE

VOLUME2

I2CBUS

LOGIC

TREBLE/BASS

/MIDDLE

SPECTRUMANALYZER

FADER

25 OUT-FL

24 OUT-RR

23 OUT-RL

FADER

FADER

22 SUBOUT-R

21

20

SUBOUT-L

19

ADJ

18

SAOUT

17

SADA

SACLK

FADER

FADER

LPF

EFFECT

INPUTGAIN

FADER

IC200 BA3121F-E2(MAIN Board (2/4))

AMP

8

4

3

2

1OUT1

VM1

IN1

GND

VCC

OUT2

VM2

IN2AMP

7

6

5

Page 31: Cdx Gt61uigt610ui

31

CDX-GT61UI/GT610UI

IC250 ATMEGA32L-8AU-S2 (MAIN Board (4/4))

PROGRAMCOUNTER

INSTRUCTIONREGISTER

INSTRUCTIONDECODER

CONTROLLINES

PROGRAMFLASH

STACKPOINTER

SRAM

GENERALPURPOSE

REGISTERS

ALU

AVR CPU

ZYX

EEPROM

OSCILLATOR

ADCINTERFACE

TIMERS/COUNTERS OSCILLATOR

TWI

MCU CTRL.& TIMING

INTERNALCALIBRATEDOSCILLATOR

STATUSREGISTER

PROGRAMMINGLOGIC

PORT BDIGITAL

INTERFACE

PORT BDRIVERS/BUFFERS

40

41

42

43

44

34ADC3AD

C4

ADC5

ADC6

ADC7

AREF

GND

AVCC

TOSC

2

TOSC

1

TDI

TDO

MOS

I

MIS

O

SCK

RESE

T

VCC

GND

XTAL

2

XTAL

1

RXD

TXD

INTO

ADC2

ADC1

ADC0

VCC

GND

XCK/T0

T1

AIN0/INT2

AIN1/OC0

SS

TMC

TCK

SDA

SCL

OC2

ICP1

VCC

GND

INT1

OC1A

OC1B

30313233

35

36

37

38

39

21 3 4 5 9 10 117 86

INTERRUPTUNIT

INTERNALOSCILLATOR

WATCHDOGTIMER

PORT ADIGITAL

INTERFACE

PORT ADRIVERS/BUFFERS

PORT CDRIVERS/BUFFERS

22

2526272829 2324

21

20

19

13

12

14

15

16

17

18

PORT CDIGITAL

INTERFACE

PORT DDIGITAL

INTERFACE

PORT DDRIVERS/BUFFERS

COMP.INTERFACE

USARTSPI

MUX &ADC

Page 32: Cdx Gt61uigt610ui

32

CDX-GT61UI/GT610UI

IC801 NJM2387ADL3 (MAIN Board (4/4))IC802 NJM2387ADL3 (MAIN Board (4/4))

1 2 3 4 5

CURRENTLIMIT

THERMALPROTECTION

OVERVOLTAGEPROTECTION

BANDGAPREFERENCE

VIN CONT VOUT VADJ GND

IC803 BD9778HFP (MAIN Board (4/4))

1 2 3 4 5

CURRENTLIMIT

PWMCOMPARATOR

ERRORAMP

L:OFFH:ON

VREF

VINTSD

OSC

VIN SW FB GND INV6

RT7

EN

VREFSOFTSTART

ON/OFF

LATCH

DRIVER

RESET

Page 33: Cdx Gt61uigt610ui

33

CDX-GT61UI/GT610UI

• IC PIN DESCRIPTIONIC501 MB90F046PF-G-105E1 (SYSTEM CONTROL) (MAIN BOARD (3/4))

Pin No. Pin Name I/O Pin Description

1 AREASEL0 I Destination setting pin 0

2 AREASEL1 I Destination setting pin 1

3 AREASEL2 I Destination setting pin 2

4 B-OUTSEL I Black-out with/without discrimination signal input “H”: Black-out

5 DIAG I Status signal input from power amplifier

6 AAC SEL I AAC play setting signal input

7 BEEP O Beep signal output to power amplifier

8 AMPSTB O Standby signal output to power amplifier

9 VOLATT O Electronic volume attenuate control signal output

10 FSW IN I D/D converter oscillator frequency count signal input

11 VSS — Ground pin

12 TUATT O Tuner mute control signal output

13 NSMASK O Noise mask signal output

14 ILLUMI SEL I Illumination voltage setting signal input

15 COL SEL I Two colors change setting signal input

16, 17 NCO O Not used. (Open)

18 FL CS O Fluorescent indicator tube chip select signal output

19 FL SO O Fluorescent indicator tube serial data signal output

20 FL SCK O Fluorescent indicator tube serial clock signal output

21, 22 NCO O Not used. (Open)

23 VCC5 — Power supply pin (+3.3 V)

24 EEP SIO I/O EEPROM bus serial data signal input/output

25 EEP CKO O EEPROM bus serial clock signal output

26 RDS ON O RDS (Radio Data System) on signal output Not used in this set.

27 MC RX I Mechanism microcomputer comunication signal input RX

28 MC TX O Mechanism microcomputer comunication signal output TX

29, 30 NCO O Not used. (Open)

31 RE IN0 I Rotary encoder signal input 0

32 RE IN1 I Rotary encoder signal input 1

33 I2C SCK O I2C bus serial clock signal output

34 I2C SIO I/O I2C bus serial data signal input/output

35 DAVDD — A/D converter power supply pin (+3.3 V)

36 AVRH — A/D converter external reference power supply pin (+3.3 V)

37 DAVSS — Ground pin

38 QUALITY I Noise detect signal input

39 VSM I S-meter voltage detect signal input

40 KEYIN1 I Key signal input 1

41 KEYIN0 I Key signal input 0

42 VSS — Ground pin

43 RCIN0 I Rotary commander key signal input Not used in this set.

44 to 47 NCO O Not used. (open)

48 AD ON O A/D converter power supply control signal output

49 MD0 I Operation mode setting pin (Connect to VDD.)

50 MD1 I Operation mode setting pin (Connect to VDD.)

51 MD2 I Operation mode setting pin (Connect to VSS.)

52 KEYACK I Key acknowledgment detect signal input

53 TUATTIN I Tuner mute zero cross detect signal input

54 BUIN I Back-up power supply detect signal input

Page 34: Cdx Gt61uigt610ui

34

CDX-GT61UI/GT610UI

55 NCO O Not used. (Open)

56 DAVN IRDS (Radio Data System) data block synchronized detect signal input

Not used in this set.

57 NCO O Not used. (Open)

58 UNISI I SONY bus data signal input

59 UNISO O SONY bus data signal output

60 UNISCK O SONY bus clock signal output

61 Z MUTE I Mute signal input

62 NOSE SW I Front panel attachment detect signal input “L”: With panel, “H”: Without panel

63 FLASH W IMemory mode change signal input Normally “H”: Single chip mode, after reset

“L”: flash write mode

64 SIRCS I Remote control signal input

65 to 70 NCO O Not used. (Open)

71 RC IN1 I Rotary commander shift key signal input Not used in this set.

72 NCO O Not used. (Open)

73 FUNC SEL OBus audio signal input/iPod audio signal input selector control signal output

“H”: iPod audio, “L”: Bus audio

74 BUSON A O Bus on signal output for iPod

75 FSW OUT OD/D converter oscillator frequency shift control signal output

“L”: 350 kHz, “H”: 415 kHz

76 NCO O Not used. (Open)

77 RESET I CPU reset signal input

78 NCO (OPEN REQ) O Not used. (Open)

79 XIN I Low speed operation clock signal input (32.768 kHz)

80 XOUT O Low speed operation clock signal output (32.768 kHz)

81 VSS1 — Ground pin

82 OSCIN I High speed operation clock signal input (18.432 MHz)

83 OSCOUT O High speed operation clock signal output (18.432 MHz)

84 VCC3 — Power supply pin (+3.3 V)

85 CYRIL SEL I Cyril correspondence discrimination signal input “L”: No correspondence

86 DEMOSEL I DEMO select signal input “H”: DEMO on, “L”: DEMO off

87 NCO O Not used. (Open)

88 SYSRST O System reset signal output

89 FL ON O Fluorescent indicator tube power on/off control signal output

90 DD ON O D/D converter power on/off control signal output

91 USB OVER I USB overcurrent detection signal input “L”: Overcurrent detection

92 USB ON O USB overcurrent detection IC control signal output “H”: On, “L”: Off

93 WAKE UP O Mechanism microcomputer wake up signal output “H”: Wake up, “L”: Sleep

94 CDON I CD mechanism servo power supply control request signal input

95 CDMON I CD mechanism deck power supply control request signal input

96 BUSON O Bus on signal output

97 TESTIN I Test mode detect signal input

98 TELATT I Telephone attenuate detect signal input

99 ACC IN I Accessory power supply detect signal input

100 ATT O Audio mute control signal output

Pin No. Pin Name I/O Pin Description

Page 35: Cdx Gt61uigt610ui

35

CDX-GT61UI/GT610UISECTION 6

EXPLODED VIEWS

1 X-2149-438-1 PANEL (FL-U) ASSY, SUB2 3-042-244-11 SCREW (T)3 X-2108-670-1 LOCK ASSY (S)4 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT5 A-1239-308-A MAIN BOARD, COMPLETE

6 2-021-848-01 SHEET (TU), GROUND7 1-833-100-11 CORD (WITH CONNECTOR) (POWER)8 1-833-886-11 CORD, CONNECTION (IPOD IN)

F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10ATU1 A-3220-961-B TUNER UNIT (TUX-032)#1 7-685-792-09 SCREW +PTT 2.6X6 (S)#2 7-685-790-01 SCREW +PTT 2.6X4 (S)#3 7-685-793-09 SCREW +PTT 2.6X8 (S)

#4 7-685-794-09 SCREW +PTT 2.6X10 (S)#5 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT#6 7-621-284-40 SCREW +P 2.6X10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

NOTE:• The mechanical parts with no reference

number in the exploded views are not supplied.• Items marked “*” are not stocked since

they are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

• -XX and -X mean standardized parts, sothey may have some difference from theoriginal one.

• Color Indication of Appearance PartsExample :

KNOB, BALANCE (WHITE) ... (RED)

Parts Color Cabinet’s Color• Accessories are given in the last of this parts list.

6-1. MAIN SECTION

R R

not supplied

not supplied

F901

not supplied

TU1

not supplied

not supplied

#1

#1

#1

#3

#3

#4

#4

#5

#6

#3

#4

#2

#1

MG-101U-188//Q

A

A

B

B

1

2

3

4

7

8

6

A

5

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

Page 36: Cdx Gt61uigt610ui

36

CDX-GT61UI/GT610UI

51 A-1239-373-A PANEL COMPLETE ASSY, FRONT (GT61UI)51 A-1239-378-A PANEL COMPLETE ASSY, FRONT (GT610UI)52 X-2176-922-1 BUTTON ASSY (S)53 X-2176-924-1 PANEL (SV) ASSY, FRONT (GT61UI)53 X-2176-925-1 PANEL (SV) ASSY, FRONT (GT610UI)

54 X-2149-353-1 KNOB (VOL) (SV) ASSY55 2-693-599-01 SPRING (RELEASE)56 2-686-937-02 PANEL (FL-U), BACK

57 3-250-543-21 SCREW (+B P-TITE M2)58 2-686-941-01 HOLDER (USB)59 X-2176-322-1 CAP (USB) ASSY60 3-251-320-01 EMBLEM (NO. 2.5), SONYCN901 1-820-620-11 PLUG, CONNECTOR 24P

CN902 1-820-877-11 CONNECTOR, USB (SOCKET) (USB)FL901 1-519-909-12 INDICATOR TUBE, FLUORESCENTRE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT/VOLUME)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

6-2. FRONT PANEL SECTION

58FL901

CN902

CN901

not supplied(KEY board)

not supplied

not supplied

not supplied

not supplied

not suppliednot supplied(AUX board)

51

52

53

59

54

55

56

57

57

RE901

60

Page 37: Cdx Gt61uigt610ui

37

CDX-GT61UI/GT610UI

101 A-1234-480-A MECHANICAL BLOCK (U) ASSY102 A-1177-169-A DAXEV//Q

0103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A)104 2-626-869-01 SCREW (M2X3), SERRATION

105 3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN106 3-352-758-31 SCREW (M1.7X2.5), TOOTHED LOCK107 A-1206-357-A SERVO BOARD, COMPLETE#7 7-627-000-08 SCREW, PRECISION +P 1.7X2.2 TYPE3

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

6-3. CD MECHANISM SECTION(MG-101U-188//Q)

NOTE: Refer to SUPPLEMENT-1 for disassembly of OPTICAL PICK-UP.

not supplied

#7#7

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

101

102

103

105

104

107

106not supplied106

Ver. 1.1

Page 38: Cdx Gt61uigt610ui

38

CDX-GT61UI/GT610UISECTION 7

ELECTRICAL PARTS LIST

AUX BOARD**********

< FERRITE BEAD >

FB901 1-414-595-11 INDUCTOR, FERRITE BEADFB902 1-414-595-11 INDUCTOR, FERRITE BEADFB903 1-500-245-11 INDUCTOR, FERRITE BEAD

< JACK >

J901 1-819-732-21 JACK (DIA. 3.5) (AUX)*************************************************************

KEY BOARD**********

< CAPACITOR >

C841 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC842 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC843 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC904 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC905 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C974 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC975 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC976 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC977 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC979 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V

C981 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC982 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

< DIODE >

D903 8-719-057-80 DIODE MA8180-M-TXD904 8-719-057-80 DIODE MA8180-M-TXD905 8-719-977-12 DIODE DTZ6.8BD906 8-719-977-12 DIODE DTZ6.8BD907 8-719-977-12 DIODE DTZ6.8B

D908 8-719-977-12 DIODE DTZ6.8BD909 8-719-420-90 DIODE MA8051-MD951 1-804-988-21 VARISTOR, CHIP (1608)D953 1-804-988-21 VARISTOR, CHIP (1608)D955 1-804-988-21 VARISTOR, CHIP (1608)

D971 8-719-420-90 DIODE MA8051-M

< FERRITE BEAD >

FB904 1-469-876-11 INDUCTOR, FERRITE BEAD

FB905 1-469-876-11 INDUCTOR, FERRITE BEADFB906 1-216-295-11 SHORT CHIP 0FB907 1-216-295-11 SHORT CHIP 0

< IC >

IC971 6-600-163-01 IC RS-770 (IR)IC972 6-706-715-01 IC NJM2867F33(TE2)

< DIODE >

LED841 6-501-547-01 LED CL-197HB1E-D-T (Z)LED842 6-501-547-01 LED CL-197HB1E-D-T (CD INDICATOR)LED843 6-501-547-01 LED CL-197HB1E-D-T (OFF)LED844 6-501-547-01 LED CL-197HB1E-D-T (EQ3)LED845 6-501-547-01 LED CL-197HB1E-D-T (BTM)

LED846 6-501-547-01 LED CL-197HB1E-D-T (SOURCE)LED847 6-501-547-01 LED CL-197HB1E-D-T (MODE)LED850 6-501-547-01 LED CL-197HB1E-D-T (DSPL)LED851 6-501-547-01 LED CL-197HB1E-D-T (1)LED852 6-501-547-01 LED CL-197HB1E-D-T (2)

LED853 6-501-547-01 LED CL-197HB1E-D-T (3)LED854 6-501-547-01 LED CL-197HB1E-D-T (4)LED855 6-501-547-01 LED CL-197HB1E-D-T (5)LED856 6-501-547-01 LED CL-197HB1E-D-T (6)LED857 6-501-547-01 LED CL-197HB1E-D-T (SCRL)

LED961 6-501-547-01 LED CL-197HB1E-D-T (RING ILLUMINATION)LED962 6-501-547-01 LED CL-197HB1E-D-T (RING ILLUMINATION)LED963 6-501-547-01 LED CL-197HB1E-D-T (RING ILLUMINATION)

< COIL >

LF901 1-457-223-11 COIL, COMMON MODE CHOKE

< SWITCH >

LSW901 1-786-998-12 SWITCH, TACTILE (WITH LED)(M > SEEK+)

LSW902 1-786-998-12 SWITCH, TACTILE (WITH LED)(. m SEEK–)

< TRANSISTOR >

Q881 8-729-600-22 TRANSISTOR 2SA1235-FQ882 8-729-600-22 TRANSISTOR 2SA1235-FQ883 8-729-600-22 TRANSISTOR 2SA1235-F

< RESISTOR >

R841 1-216-815-11 METAL CHIP 330 5% 1/10W

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

NOTE:• Due to standardization, replacements in

the parts list may be different from theparts specified in the diagrams or thecomponents used on the set.

• -XX and -X mean standardized parts, sothey may have some difference from theoriginal one.

• RESISTORSAll resistors are in ohms.METAL:Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F:nonflammable

• Items marked “*” are not stocked sincethey are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

• SEMICONDUCTORSIn each case, u : µ, for example:uA.. : µA.. uPA.. : µPA..uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..

• CAPACITORSuF : µF

• COILSuH : µH

KEYAUX

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

When indicating parts by referencenumber, please include the board.

Page 39: Cdx Gt61uigt610ui

39

CDX-GT61UI/GT610UI

R842 1-216-814-11 METAL CHIP 270 5% 1/10WR843 1-216-815-11 METAL CHIP 330 5% 1/10WR844 1-216-814-11 METAL CHIP 270 5% 1/10WR845 1-216-818-11 METAL CHIP 560 5% 1/10WR846 1-216-817-11 METAL CHIP 470 5% 1/10W

R849 1-216-815-11 METAL CHIP 330 5% 1/10WR850 1-216-814-11 METAL CHIP 270 5% 1/10WR851 1-216-815-11 METAL CHIP 330 5% 1/10WR852 1-216-814-11 METAL CHIP 270 5% 1/10WR853 1-216-815-11 METAL CHIP 330 5% 1/10W

R854 1-216-814-11 METAL CHIP 270 5% 1/10WR855 1-216-821-11 METAL CHIP 1K 5% 1/10WR856 1-216-821-11 METAL CHIP 1K 5% 1/10WR857 1-216-864-11 SHORT CHIP 0R859 1-216-815-11 METAL CHIP 330 5% 1/10W

R860 1-216-814-11 METAL CHIP 270 5% 1/10WR881 1-216-821-11 METAL CHIP 1K 5% 1/10WR882 1-216-821-11 METAL CHIP 1K 5% 1/10WR883 1-216-821-11 METAL CHIP 1K 5% 1/10WR884 1-216-833-11 METAL CHIP 10K 5% 1/10W

R885 1-216-833-11 METAL CHIP 10K 5% 1/10WR886 1-216-833-11 METAL CHIP 10K 5% 1/10WR887 1-216-845-11 METAL CHIP 100K 5% 1/10WR888 1-216-845-11 METAL CHIP 100K 5% 1/10WR889 1-216-845-11 METAL CHIP 100K 5% 1/10W

R901 1-216-820-11 METAL CHIP 820 5% 1/10WR902 1-216-821-11 METAL CHIP 1K 5% 1/10WR903 1-216-821-11 METAL CHIP 1K 5% 1/10WR904 1-216-822-11 METAL CHIP 1.2K 5% 1/10WR905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R906 1-216-820-11 METAL CHIP 820 5% 1/10WR907 1-216-821-11 METAL CHIP 1K 5% 1/10WR908 1-216-821-11 METAL CHIP 1K 5% 1/10WR909 1-216-822-11 METAL CHIP 1.2K 5% 1/10WR910 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R911 1-216-824-11 METAL CHIP 1.8K 5% 1/10WR912 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR913 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR914 1-216-828-11 METAL CHIP 3.9K 5% 1/10WR915 1-216-830-11 METAL CHIP 5.6K 5% 1/10W

R921 1-216-295-11 SHORT CHIP 0R922 1-216-295-11 SHORT CHIP 0R947 1-216-811-11 METAL CHIP 150 5% 1/10WR948 1-216-811-11 METAL CHIP 150 5% 1/10WR961 1-216-821-11 METAL CHIP 1K 5% 1/10W

R962 1-216-864-11 SHORT CHIP 0R963 1-216-821-11 METAL CHIP 1K 5% 1/10WR964 1-216-818-11 METAL CHIP 560 5% 1/10WR965 1-216-817-11 METAL CHIP 470 5% 1/10WR971 1-216-809-11 METAL CHIP 100 5% 1/10W

R974 1-216-809-11 METAL CHIP 100 5% 1/10WR975 1-216-809-11 METAL CHIP 100 5% 1/10WR976 1-216-809-11 METAL CHIP 100 5% 1/10WR977 1-216-809-11 METAL CHIP 100 5% 1/10WR978 1-216-864-11 SHORT CHIP 0

R981 1-218-893-11 METAL CHIP 82K 0.5% 1/10WR982 1-216-841-11 METAL CHIP 47K 5% 1/10WR983 1-216-801-11 METAL CHIP 22 5% 1/10W

R984 1-216-801-11 METAL CHIP 22 5% 1/10WR988 1-216-864-11 SHORT CHIP 0R989 1-216-845-11 METAL CHIP 100K 5% 1/10WR993 1-216-809-11 METAL CHIP 100 5% 1/10WR994 1-216-809-11 METAL CHIP 100 5% 1/10W

R995 1-216-809-11 METAL CHIP 100 5% 1/10W

< NETWORK RESISTOR >

RB901 1-239-662-81 RESISTOR, NETWORK 10X2

< SWITCH >

S901 1-786-653-21 SWITCH, TACTILE (Z)S902 1-786-653-21 SWITCH, TACTILE (OFF)S903 1-786-653-21 SWITCH, TACTILE (SOURCE)S904 1-786-653-21 SWITCH, TACTILE (EQ3)S906 1-786-653-21 SWITCH, TACTILE (BTM/CAT)

S907 1-786-653-21 SWITCH, TACTILE (MODE)S908 1-786-653-21 SWITCH, TACTILE (DSPL/DIM)S909 1-786-653-21 SWITCH, TACTILE (1/GP/ALBM –)S910 1-786-653-21 SWITCH, TACTILE (2/GP/ALBM +)S911 1-786-653-21 SWITCH, TACTILE (3/REP)

S912 1-786-653-21 SWITCH, TACTILE (4/SHUF)S913 1-786-653-21 SWITCH, TACTILE (5)S914 1-786-653-21 SWITCH, TACTILE (6/PAUSE)S915 1-786-653-21 SWITCH, TACTILE (SCRL)

*************************************************************

A-1239-308-A MAIN BOARD, COMPLETE*********************

7-621-284-40 SCREW +P 2.6X107-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT7-685-794-09 SCREW +PTT 2.6X10 (S)

< CAPACITOR >

C2 1-126-947-11 ELECT 47uF 20% 35VC3 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC5 1-126-947-11 ELECT 47uF 20% 35VC6 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C8 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC15 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC151 1-126-960-11 ELECT 1uF 20% 50VC152 1-126-960-11 ELECT 1uF 20% 50VC153 1-126-961-11 ELECT 2.2uF 20% 50V

C154 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50VC155 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50VC157 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC200 1-126-964-11 ELECT 10uF 20% 50VC201 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C202 1-124-589-11 ELECT 47uF 20% 16VC203 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC204 1-124-584-00 ELECT 100uF 20% 10VC205 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC206 1-126-963-11 ELECT 4.7uF 20% 50V

C207 1-126-964-11 ELECT 10uF 20% 50VC210 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC211 1-126-963-11 ELECT 4.7uF 20% 50VC212 1-126-964-11 ELECT 10uF 20% 50V

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

MAINKEY

Page 40: Cdx Gt61uigt610ui

40

CDX-GT61UI/GT610UI

C213 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC214 1-126-964-11 ELECT 10uF 20% 50VC215 1-124-233-11 ELECT 10uF 20% 16VC220 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC221 1-126-963-11 ELECT 4.7uF 20% 50V

C222 1-126-964-11 ELECT 10uF 20% 50VC223 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC224 1-126-964-11 ELECT 10uF 20% 50VC225 1-124-233-11 ELECT 10uF 20% 16VC250 1-164-730-11 CERAMIC CHIP 0.0012uF 10% 50V

C251 1-162-917-11 CERAMIC CHIP 15PF 5% 50VC252 1-162-917-11 CERAMIC CHIP 15PF 5% 50VC253 1-164-730-11 CERAMIC CHIP 0.0012uF 10% 50VC254 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC255 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C256 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC257 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50VC258 1-124-233-11 ELECT 10uF 20% 16VC259 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC260 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C261 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC301 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC302 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC303 1-128-551-11 ELECT 22uF 20% 63VC304 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V

C305 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC306 1-124-233-11 ELECT 10uF 20% 16VC307 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC308 1-124-233-11 ELECT 10uF 20% 16VC309 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V

C312 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC314 1-124-233-11 ELECT 10uF 20% 16VC315 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC316 1-124-233-11 ELECT 10uF 20% 16VC317 1-125-889-11 CERAMIC CHIP 2.2uF 10% 10V

C318 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC319 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC320 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC325 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC329 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C330 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC361 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC362 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC363 1-124-257-00 ELECT 2.2uF 20% 50VC364 1-124-257-00 ELECT 2.2uF 20% 50V

C365 1-126-960-11 ELECT 1uF 20% 50VC366 1-126-960-11 ELECT 1uF 20% 50VC367 1-126-960-11 ELECT 1uF 20% 50VC368 1-126-960-11 ELECT 1uF 20% 50VC401 1-124-234-00 ELECT 22uF 20% 16V

C402 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC403 1-124-584-00 ELECT 100uF 20% 10VC405 1-124-234-00 ELECT 22uF 20% 16VC406 1-124-257-00 ELECT 2.2uF 20% 50VC407 1-124-257-00 ELECT 2.2uF 20% 50V

C409 1-124-233-11 ELECT 10uF 20% 16VC412 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC413 1-163-251-11 CERAMIC CHIP 100PF 5% 50V

C414 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC415 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC417 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC418 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC419 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C421 1-126-964-11 ELECT 10uF 20% 50VC423 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC424 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC426 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC431 1-126-964-11 ELECT 10uF 20% 50V

C432 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC434 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC441 1-126-964-11 ELECT 10uF 20% 50VC443 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC444 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C445 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC451 1-126-964-11 ELECT 10uF 20% 50VC452 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC454 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC461 1-126-964-11 ELECT 10uF 20% 50V

C462 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC463 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC471 1-126-964-11 ELECT 10uF 20% 50VC472 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC473 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

C484 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC485 1-124-584-00 ELECT 100uF 20% 10VC486 1-124-233-11 ELECT 10uF 20% 16VC491 1-126-947-11 ELECT 47uF 20% 35VC493 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V

C494 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC501 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC502 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC504 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC507 1-162-917-11 CERAMIC CHIP 15PF 5% 50V

C508 1-162-917-11 CERAMIC CHIP 15PF 5% 50VC509 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC510 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC512 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC513 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C514 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC515 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC516 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC519 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC600 1-126-935-11 ELECT 470uF 20% 16V

C601 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC622 1-126-924-11 ELECT 330uF 20% 10VC623 1-126-916-11 ELECT 1000uF 20% 6.3VC624 1-126-176-11 ELECT 220uF 20% 10VC681 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C682 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC683 1-124-584-00 ELECT 100uF 20% 10VC701 1-131-868-81 ELECT 3300uF 20% 16VC702 1-126-960-11 ELECT 1uF 20% 50VC704 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V

C705 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC802 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC803 1-124-589-11 ELECT 47uF 20% 16V

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

MAIN

Page 41: Cdx Gt61uigt610ui

41

CDX-GT61UI/GT610UI

C804 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC805 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC806 1-124-589-11 ELECT 47uF 20% 16VC807 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC808 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C809 1-126-933-11 ELECT 100uF 20% 16VC810 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC811 1-124-584-00 ELECT 100uF 20% 10VC812 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25VC814 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C816 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC817 1-126-933-11 ELECT 100uF 20% 16VC818 1-126-933-11 ELECT 100uF 20% 16VC820 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC822 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C823 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC890 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC891 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC901 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC902 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

C914 1-216-864-11 SHORT CHIP 0C998 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

< CONNECTOR >

CN200 1-564-705-11 PIN, CONNECTOR (SMALL TYPE) 3PCN250 1-564-709-11 PIN, CONNECTOR (SMALL TYPE) 7PCN300 1-774-701-21 PIN, CONNECTOR 16PCN350 1-820-611-11 CONNECTOR, BOARD TO BOARD 28PCN352 1-564-719-11 PIN, CONNECTOR (SMALL TYPE) 3P

CN370 1-820-621-11 SOCKET, CONNECTOR 24PCNJ400 1-580-907-41 PLUG, CONNECTOR 8P (BUS CONTROL IN)

< DIODE >

D2 8-719-977-03 DIODE DTZ5.6BD101 6-501-193-01 DIODE 1SS355WTE-17D102 6-501-193-01 DIODE 1SS355WTE-17D103 8-719-977-12 DIODE DTZ6.8BD104 8-719-977-12 DIODE DTZ6.8B

D105 8-719-977-12 DIODE DTZ6.8BD106 8-719-977-12 DIODE DTZ6.8BD107 8-719-977-12 DIODE DTZ6.8BD108 8-719-977-12 DIODE DTZ6.8BD109 8-719-977-12 DIODE DTZ6.8B

D110 8-719-977-12 DIODE DTZ6.8BD111 8-719-977-12 DIODE DTZ6.8BD112 8-719-977-12 DIODE DTZ6.8BD113 8-719-977-12 DIODE DTZ6.8BD151 1-805-043-11 ABSORBER, CHIP SURGE

D152 1-805-043-11 ABSORBER, CHIP SURGED153 8-719-057-80 DIODE MA8180-M-TXD156 8-719-977-12 DIODE DTZ6.8BD250 8-719-060-48 DIODE RB751V-40TE-17D251 6-501-013-01 DIODE BAT54ALT1G

D252 8-719-057-80 DIODE MA8180-M-TXD253 8-719-057-80 DIODE MA8180-M-TXD254 8-719-977-12 DIODE DTZ6.8BD255 8-719-060-48 DIODE RB751V-40TE-17D301 6-501-362-01 DIODE 1A4-TA26

D302 6-501-362-01 DIODE 1A4-TA26D303 6-501-362-01 DIODE 1A4-TA26D304 6-501-362-01 DIODE 1A4-TA26D305 6-501-362-01 DIODE 1A4-TA26D306 6-501-362-01 DIODE 1A4-TA26

D307 6-501-362-01 DIODE 1A4-TA26D308 6-501-362-01 DIODE 1A4-TA26D309 6-501-362-01 DIODE 1A4-TA26D310 6-501-362-01 DIODE 1A4-TA26D311 6-501-362-01 DIODE 1A4-TA26

D312 6-501-362-01 DIODE 1A4-TA26D353 6-501-013-01 DIODE BAT54ALT1GD491 6-501-193-01 DIODE 1SS355WTE-17D502 8-719-060-48 DIODE RB751V-40TE-17D503 6-501-193-01 DIODE 1SS355WTE-17

D602 8-719-057-80 DIODE MA8180-M-TXD603 8-719-422-64 DIODE MA8062-MD604 8-719-057-80 DIODE MA8180-M-TXD605 8-719-057-80 DIODE MA8180-M-TXD606 8-719-072-70 DIODE MA2ZD14001S0

D607 6-501-571-01 DIODE 1N5404-C311-3D609 6-501-051-01 DIODE BAT54CLT1GD702 8-719-057-80 DIODE MA8180-M-TXD703 8-719-057-80 DIODE MA8180-M-TXD706 8-719-057-80 DIODE MA8180-M-TX

D707 8-719-057-80 DIODE MA8180-M-TXD801 8-719-420-90 DIODE MA8051-MD802 6-501-657-01 DIODE MA24D5000BS0D804 8-719-053-18 DIODE 1SR154-400TE-25D901 8-719-057-80 DIODE MA8180-M-TX

< IC >

IC200 8-759-048-67 IC BA3121FIC201 8-759-357-68 IC NJM2115M-TE2IC250 6-807-330-01 IC ATMEGA32L-8AU-S2IC300 6-705-359-02 IC TDA8588AJ/N2/R1IC401 6-710-065-01 IC BD3442FS-E2

IC402 8-759-391-88 IC MC14066BDTR2IC501 6-807-331-01 IC MB90F046PF-G-105E1IC601 6-703-884-01 IC BA8271F-E2IC602 6-709-458-01 IC XC61CN2802NRIC681 6-704-529-01 IC XC6206P332PR

IC801 6-709-213-01 IC NJM2387ADL3(TE2)IC802 6-709-213-01 IC NJM2387ADL3(TE2)IC803 6-707-911-01 IC BD9778HFPIC804 6-710-624-01 IC TPS2051BDRG4

< JACK >

J1 1-815-185-13 JACK (ANTENNA)J652 1-774-699-12 JACK, PIN 4P (BUS AUDIO IN/

AUDIO OUT REAR)

< COIL >

L1 1-216-295-11 SHORT CHIP 0L4 1-216-295-11 SHORT CHIP 0L151 1-500-245-11 INDUCTOR, FERRITE BEADL250 1-414-398-11 INDUCTOR 10uHL251 1-216-295-11 SHORT CHIP 0

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

MAIN

Page 42: Cdx Gt61uigt610ui

42

CDX-GT61UI/GT610UI

L300 1-456-617-11 COIL, CHOKEL401 1-216-864-11 SHORT CHIP 0L402 1-216-295-11 SHORT CHIP 0L403 1-216-295-11 SHORT CHIP 0L405 1-469-876-11 INDUCTOR, FERRITE BEAD

L406 1-500-245-11 INDUCTOR, FERRITE BEADL407 1-216-864-11 SHORT CHIP 0L409 1-469-844-11 INDUCTOR 2.2uHL410 1-216-864-11 SHORT CHIP 0L501 1-216-295-11 SHORT CHIP 0

L802 1-416-831-11 INDUCTOR 100uHL803 1-457-384-11 INDUCTOR 47uHL804 1-216-295-11 SHORT CHIP 0L805 1-216-295-11 SHORT CHIP 0L818 1-457-383-11 INDUCTOR 100uH

L901 1-216-295-11 SHORT CHIP 0L902 1-469-844-11 INDUCTOR 2.2uH

< TRANSISTOR >

Q3 6-551-431-01 TRANSISTOR 2SC6027T100-QRQ200 8-729-043-80 TRANSISTOR UMD3N-TRQ210 6-550-752-01 TRANSISTOR DTC614TKT146Q220 6-550-752-01 TRANSISTOR DTC614TKT146Q250 8-729-105-29 TRANSISTOR 2SA1385-L

Q251 8-729-027-43 TRANSISTOR DTC114EKA-T146Q252 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q253 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q254 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q255 8-729-120-28 TRANSISTOR 2SC1623-L5L6

Q256 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q257 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q258 8-729-027-43 TRANSISTOR DTC114EKA-T146Q401 8-729-027-44 TRANSISTOR DTC114TKA-T146Q402 8-729-027-44 TRANSISTOR DTC114TKA-T146

Q411 8-729-027-43 TRANSISTOR DTC114EKA-T146Q412 8-729-027-23 TRANSISTOR DTA114EKA-T146Q413 8-729-043-80 TRANSISTOR UMD3N-TRQ420 8-729-027-44 TRANSISTOR DTC114TKA-T146Q432 6-550-752-01 TRANSISTOR DTC614TKT146

Q440 8-729-027-44 TRANSISTOR DTC114TKA-T146Q452 6-550-752-01 TRANSISTOR DTC614TKT146Q460 8-729-027-44 TRANSISTOR DTC114TKA-T146Q470 8-729-027-44 TRANSISTOR DTC114TKA-T146Q491 8-729-027-23 TRANSISTOR DTA114EKA-T146

Q492 8-729-027-43 TRANSISTOR DTC114EKA-T146Q605 8-729-027-43 TRANSISTOR DTC114EKA-T146Q664 8-729-027-23 TRANSISTOR DTA114EKA-T146Q702 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q805 8-729-027-43 TRANSISTOR DTC114EKA-T146

< RESISTOR >

R2 1-216-839-11 METAL CHIP 33K 5% 1/10WR3 1-216-843-11 METAL CHIP 68K 5% 1/10WR4 1-216-839-11 METAL CHIP 33K 5% 1/10WR5 1-216-843-11 METAL CHIP 68K 5% 1/10WR6 1-216-809-11 METAL CHIP 100 5% 1/10W

R7 1-216-809-11 METAL CHIP 100 5% 1/10WR9 1-216-843-11 METAL CHIP 68K 5% 1/10W

R10 1-216-821-11 METAL CHIP 1K 5% 1/10WR12 1-216-864-11 SHORT CHIP 0R13 1-216-864-11 SHORT CHIP 0R150 1-216-864-11 SHORT CHIP 0R151 1-216-817-11 METAL CHIP 470 5% 1/10W

R152 1-216-817-11 METAL CHIP 470 5% 1/10WR153 1-216-834-11 METAL CHIP 12K 5% 1/10WR154 1-216-834-11 METAL CHIP 12K 5% 1/10WR155 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR156 1-216-296-11 SHORT CHIP 0

R200 1-216-864-11 SHORT CHIP 0R201 1-216-864-11 SHORT CHIP 0R202 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR203 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR204 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R210 1-216-041-00 RES-CHIP 470 5% 1/10WR211 1-216-833-11 METAL CHIP 10K 5% 1/10WR212 1-216-838-11 METAL CHIP 27K 5% 1/10WR214 1-216-841-11 METAL CHIP 47K 5% 1/10WR215 1-216-837-11 METAL CHIP 22K 5% 1/10W

R216 1-216-839-11 METAL CHIP 33K 5% 1/10WR217 1-216-842-11 METAL CHIP 56K 5% 1/10WR218 1-216-841-11 METAL CHIP 47K 5% 1/10WR219 1-216-822-11 METAL CHIP 1.2K 5% 1/10WR220 1-216-041-00 RES-CHIP 470 5% 1/10W

R221 1-216-833-11 METAL CHIP 10K 5% 1/10WR222 1-216-838-11 METAL CHIP 27K 5% 1/10WR224 1-216-841-11 METAL CHIP 47K 5% 1/10WR225 1-216-837-11 METAL CHIP 22K 5% 1/10WR226 1-216-839-11 METAL CHIP 33K 5% 1/10W

R227 1-216-842-11 METAL CHIP 56K 5% 1/10WR228 1-216-841-11 METAL CHIP 47K 5% 1/10WR229 1-216-822-11 METAL CHIP 1.2K 5% 1/10WR250 1-216-841-11 METAL CHIP 47K 5% 1/10WR251 1-216-833-11 METAL CHIP 10K 5% 1/10W

R252 1-216-864-11 SHORT CHIP 0R253 1-216-833-11 METAL CHIP 10K 5% 1/10WR254 1-216-864-11 SHORT CHIP 0R255 1-216-833-11 METAL CHIP 10K 5% 1/10WR256 1-216-845-11 METAL CHIP 100K 5% 1/10W

R257 1-216-845-11 METAL CHIP 100K 5% 1/10WR259 1-216-845-11 METAL CHIP 100K 5% 1/10WR260 1-216-845-11 METAL CHIP 100K 5% 1/10WR261 1-216-845-11 METAL CHIP 100K 5% 1/10WR262 1-216-845-11 METAL CHIP 100K 5% 1/10W

R263 1-216-845-11 METAL CHIP 100K 5% 1/10WR264 1-216-845-11 METAL CHIP 100K 5% 1/10WR265 1-216-845-11 METAL CHIP 100K 5% 1/10WR266 1-216-845-11 METAL CHIP 100K 5% 1/10WR267 1-216-845-11 METAL CHIP 100K 5% 1/10W

R268 1-216-845-11 METAL CHIP 100K 5% 1/10WR270 1-216-821-11 METAL CHIP 1K 5% 1/10WR271 1-216-845-11 METAL CHIP 100K 5% 1/10WR272 1-216-206-00 RES-CHIP 2.2K 5% 1/8WR273 1-216-296-11 SHORT CHIP 0

R274 1-216-833-11 METAL CHIP 10K 5% 1/10WR275 1-216-833-11 METAL CHIP 10K 5% 1/10WR276 1-216-833-11 METAL CHIP 10K 5% 1/10W

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

MAIN

Page 43: Cdx Gt61uigt610ui

43

CDX-GT61UI/GT610UI

R277 1-216-833-11 METAL CHIP 10K 5% 1/10WR278 1-216-833-11 METAL CHIP 10K 5% 1/10WR279 1-216-833-11 METAL CHIP 10K 5% 1/10WR280 1-218-912-11 METAL CHIP 510K 0.5% 1/10WR281 1-218-885-11 METAL CHIP 39K 0.5% 1/10W

R282 1-414-595-11 INDUCTOR, FERRITE BEADR283 1-414-595-11 INDUCTOR, FERRITE BEADR284 1-216-845-11 METAL CHIP 100K 5% 1/10WR285 1-216-845-11 METAL CHIP 100K 5% 1/10WR286 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R287 1-216-833-11 METAL CHIP 10K 5% 1/10WR288 1-216-845-11 METAL CHIP 100K 5% 1/10WR289 1-216-864-11 SHORT CHIP 0R290 1-216-296-11 SHORT CHIP 0R291 1-216-296-11 SHORT CHIP 0

R292 1-216-864-11 SHORT CHIP 0R293 1-216-206-00 RES-CHIP 2.2K 5% 1/8WR294 1-216-206-00 RES-CHIP 2.2K 5% 1/8WR295 1-216-206-00 RES-CHIP 2.2K 5% 1/8WR301 1-216-811-11 METAL CHIP 150 5% 1/10W

R302 1-216-841-11 METAL CHIP 47K 5% 1/10WR351 1-216-845-11 METAL CHIP 100K 5% 1/10WR355 1-216-833-11 METAL CHIP 10K 5% 1/10WR356 1-216-833-11 METAL CHIP 10K 5% 1/10WR357 1-216-821-11 METAL CHIP 1K 5% 1/10W

R358 1-216-821-11 METAL CHIP 1K 5% 1/10WR401 1-216-817-11 METAL CHIP 470 5% 1/10WR402 1-216-817-11 METAL CHIP 470 5% 1/10WR403 1-216-837-11 METAL CHIP 22K 5% 1/10WR404 1-216-837-11 METAL CHIP 22K 5% 1/10W

R413 1-216-833-11 METAL CHIP 10K 5% 1/10WR420 1-216-809-11 METAL CHIP 100 5% 1/10WR421 1-216-821-11 METAL CHIP 1K 5% 1/10WR423 1-216-864-11 SHORT CHIP 0R430 1-216-809-11 METAL CHIP 100 5% 1/10W

R431 1-216-809-11 METAL CHIP 100 5% 1/10WR440 1-216-809-11 METAL CHIP 100 5% 1/10WR442 1-216-821-11 METAL CHIP 1K 5% 1/10WR443 1-216-864-11 SHORT CHIP 0R447 1-216-833-11 METAL CHIP 10K 5% 1/10W

R448 1-216-833-11 METAL CHIP 10K 5% 1/10WR449 1-216-833-11 METAL CHIP 10K 5% 1/10WR450 1-216-833-11 METAL CHIP 10K 5% 1/10WR451 1-216-809-11 METAL CHIP 100 5% 1/10WR452 1-216-809-11 METAL CHIP 100 5% 1/10W

R460 1-216-809-11 METAL CHIP 100 5% 1/10WR461 1-216-821-11 METAL CHIP 1K 5% 1/10WR462 1-216-833-11 METAL CHIP 10K 5% 1/10WR463 1-216-864-11 SHORT CHIP 0R470 1-216-809-11 METAL CHIP 100 5% 1/10W

R471 1-216-821-11 METAL CHIP 1K 5% 1/10WR472 1-216-833-11 METAL CHIP 10K 5% 1/10WR473 1-216-864-11 SHORT CHIP 0R485 1-218-883-11 METAL CHIP 33K 0.5% 1/10WR491 1-216-805-11 METAL CHIP 47 5% 1/10W

R499 1-216-864-11 SHORT CHIP 0R502 1-216-809-11 METAL CHIP 100 5% 1/10WR503 1-216-809-11 METAL CHIP 100 5% 1/10W

Ref. No. Part No. Description Remark

R504 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR505 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR507 1-216-845-11 METAL CHIP 100K 5% 1/10WR509 1-216-809-11 METAL CHIP 100 5% 1/10WR510 1-216-809-11 METAL CHIP 100 5% 1/10W

R511 1-216-809-11 METAL CHIP 100 5% 1/10WR517 1-216-841-11 METAL CHIP 47K 5% 1/10WR519 1-216-845-11 METAL CHIP 100K 5% 1/10WR520 1-216-809-11 METAL CHIP 100 5% 1/10WR521 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R522 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR523 1-216-809-11 METAL CHIP 100 5% 1/10WR526 1-216-845-11 METAL CHIP 100K 5% 1/10WR529 1-216-809-11 METAL CHIP 100 5% 1/10WR531 1-216-845-11 METAL CHIP 100K 5% 1/10W

R532 1-216-845-11 METAL CHIP 100K 5% 1/10WR533 1-216-845-11 METAL CHIP 100K 5% 1/10WR534 1-216-833-11 METAL CHIP 10K 5% 1/10WR536 1-216-845-11 METAL CHIP 100K 5% 1/10WR538 1-216-845-11 METAL CHIP 100K 5% 1/10W

R540 1-216-845-11 METAL CHIP 100K 5% 1/10WR544 1-216-809-11 METAL CHIP 100 5% 1/10WR551 1-216-845-11 METAL CHIP 100K 5% 1/10WR552 1-216-845-11 METAL CHIP 100K 5% 1/10WR553 1-216-839-11 METAL CHIP 33K 5% 1/10W

R556 1-216-845-11 METAL CHIP 100K 5% 1/10WR557 1-216-809-11 METAL CHIP 100 5% 1/10WR558 1-216-833-11 METAL CHIP 10K 5% 1/10WR560 1-216-845-11 METAL CHIP 100K 5% 1/10WR561 1-216-845-11 METAL CHIP 100K 5% 1/10W

R563 1-216-845-11 METAL CHIP 100K 5% 1/10WR565 1-216-845-11 METAL CHIP 100K 5% 1/10WR567 1-216-845-11 METAL CHIP 100K 5% 1/10WR568 1-216-849-11 METAL CHIP 220K 5% 1/10WR569 1-216-845-11 METAL CHIP 100K 5% 1/10W

R570 1-216-809-11 METAL CHIP 100 5% 1/10WR572 1-216-845-11 METAL CHIP 100K 5% 1/10WR592 1-216-809-11 METAL CHIP 100 5% 1/10WR593 1-216-809-11 METAL CHIP 100 5% 1/10WR595 1-216-833-11 METAL CHIP 10K 5% 1/10W

R596 1-216-833-11 METAL CHIP 10K 5% 1/10WR597 1-216-864-11 SHORT CHIP 0R598 1-216-864-11 SHORT CHIP 0R599 1-216-845-11 METAL CHIP 100K 5% 1/10WR600 1-216-845-11 METAL CHIP 100K 5% 1/10W

R601 1-216-851-11 METAL CHIP 330K 5% 1/10WR602 1-216-851-11 METAL CHIP 330K 5% 1/10WR603 1-216-821-11 METAL CHIP 1K 5% 1/10WR604 1-216-835-11 METAL CHIP 15K 5% 1/10WR606 1-216-821-11 METAL CHIP 1K 5% 1/10W

R607 1-216-821-11 METAL CHIP 1K 5% 1/10WR612 1-216-809-11 METAL CHIP 100 5% 1/10WR615 1-216-809-11 METAL CHIP 100 5% 1/10WR636 1-216-845-11 METAL CHIP 100K 5% 1/10WR673 1-216-833-11 METAL CHIP 10K 5% 1/10W

R674 1-216-845-11 METAL CHIP 100K 5% 1/10WR705 1-249-425-11 CARBON 4.7K 5% 1/4WR706 1-216-841-11 METAL CHIP 47K 5% 1/10W

Ref. No. Part No. Description Remark

MAIN

Page 44: Cdx Gt61uigt610ui

44

CDX-GT61UI/GT610UI

R707 1-216-841-11 METAL CHIP 47K 5% 1/10WR708 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR709 1-216-833-11 METAL CHIP 10K 5% 1/10WR800 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR802 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R803 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR809 1-216-821-11 METAL CHIP 1K 5% 1/10WR810 1-216-832-11 METAL CHIP 8.2K 5% 1/10WR811 1-216-821-11 METAL CHIP 1K 5% 1/10WR812 1-216-822-11 METAL CHIP 1.2K 5% 1/10W

R813 1-216-821-11 METAL CHIP 1K 5% 1/10WR814 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR815 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR816 1-218-883-11 METAL CHIP 33K 0.5% 1/10WR817 1-218-869-11 METAL CHIP 8.2K 0.5% 1/10W

R818 1-218-878-11 METAL CHIP 20K 0.5% 1/10WR819 1-216-844-11 METAL CHIP 82K 5% 1/10WR820 1-216-851-11 METAL CHIP 330K 5% 1/10WR821 1-216-864-11 SHORT CHIP 0R902 1-216-809-11 METAL CHIP 100 5% 1/10W

R903 1-216-809-11 METAL CHIP 100 5% 1/10WR910 1-216-864-11 SHORT CHIP 0R914 1-216-817-11 METAL CHIP 470 5% 1/10WR915 1-216-817-11 METAL CHIP 470 5% 1/10WR916 1-216-817-11 METAL CHIP 470 5% 1/10W

R924 1-216-845-11 METAL CHIP 100K 5% 1/10WR925 1-216-864-11 SHORT CHIP 0R951 1-216-797-11 METAL CHIP 10 5% 1/10WR952 1-216-797-11 METAL CHIP 10 5% 1/10W

< SWITCH >

S103 1-786-826-11 SWITCH, TACTILE (RESET)

< THERMISTOR (POSITIVE) >

TH400 1-803-350-21 THERMISTOR, POSITIVE

< TUNER UNIT >

TU1 A-3220-961-B TUNER UNIT (TUX-032)

< VIBRATOR >

X250 1-813-814-11 VIBRATOR, CRYSTAL (7.3728MHz)X501 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)X502 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)

*************************************************************

A-1206-357-A SERVO BOARD, COMPLETE**********************

*************************************************************

MISCELLANEOUS***************

7 1-833-100-11 CORD (WITH CONNECTOR) (POWER)8 1-833-886-11 CORD, CONNECTION (IPOD IN)

0103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A)CN901 1-820-620-11 PLUG, CONNECTOR 24PCN902 1-820-877-11 CONNECTOR, USB (SOCKET) (USB)

F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10AFL901 1-519-909-12 INDICATOR TUBE, FLUORESCENTRE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT/VOLUME)

*************************************************************

ACCESSORIES************

1-479-077-13 REMOTE COMMANDER (RM-X151)2-548-729-01 LID, BATTERY CASE (for RM-X151)3-096-839-11 MANUAL, INSTRUCTION (ENGLISH,SPANISH)

(GT61UI)3-096-839-21 MANUAL, INSTRUCTION (ENGLISH,FRENCH)

(GT610UI)3-096-840-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,

SPANISH) (GT61UI)

3-096-840-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH,FRENCH) (GT610UI)

X-2176-322-1 CAP (USB) ASSY*************************************************************

PARTS FOR INSTALLATION AND CONNECTIONS***************************************

151 X-3382-647-1 FRAME ASSY, FITTING152 2-686-803-01 COLLAR153 3-246-471-01 KEY (FRAME)154 3-934-325-01 SCREW, +K (5X8) TAPPING155 1-833-100-11 CORD (WITH CONNECTOR) (POWER)

MAIN SERVO

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

151

154

152 153

× 2

155

× 4

Page 45: Cdx Gt61uigt610ui

SERVICE MANUAL

9-887-538-81

Ver. 1.1 2007.04

SUPPLEMENT-1File this supplement with the service manual.

Subject: Notes for removal of the OPTICAL PICK-UP added.

DISASSEMBLY

1. CHUCKING ARM SUB ASSY

3 chucking arm sub assy

2

1 spring

Note: Have this portion receive the chassis. Note: Have this portion receive the chassis.

Note: Be careful not to touch the turn table.

US Model

CDX-GT61UI/GT610UI

Page 46: Cdx Gt61uigt610ui

2

CDX-GT61UI/GT610UI

2. SLED MOTOR ASSY

3 sled mtor assy

sled mtor assy

1 spring

spring

stand

stand

turn table

2 three serration screws(M 2 × 3)

three serration screws(M 2 × 3)

Note: Place the stand with care not to touch the turn table.

Note: Never remove these parts since they were adjusted.

Note for Assembly

Note: Take care to prevent the chassis from being bent when tightening the three machine screws.

Page 47: Cdx Gt61uigt610ui

3

CDX-GT61UI/GT610UI

3. OPTICAL PICK-UP SECTION

4. OPTICAL PICK-UP

1

2 optical pick-up section

Note: Be careful not to touch the lens and hologram terminal when removing the optical pick-up section.

There is space at the end of the leaf spring (sub guide) to avoid contact with the slide.

1 pan tapping screw(M 1.4 × 2.5)

2 leaf spring (sub guide)

3 leaf spring (OP)

5 optical pick-up

4 lead screw assy

Notes for Assembly

Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base.

Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base.

Page 48: Cdx Gt61uigt610ui

4

CDX-GT61UI/GT610UI

REVISION HISTORY

Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.

Ver. Date Description of Revision

1.0 2007.01 New

1.1 2007.04 Notes for removal of the OPTICAL PICK-UP added.

(SUPPLEMENT-1) (ENG-07003)