Drainage - 3.09

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Expansion Joints - 3.21

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Cap Sheet Repair - 4.20.1, 6.20.1

NOTE: Use of the above may or may not be applicable to your specific roof.

COMMERCIAL & INDUSTRIALROOFING PRODUCTS

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

WOODBUR

Accessories, Options & Additional ConsiderationsTECHNICAL BINDER REFERENCE

A properly designed and constructed roof deck, as well as the properinterrelationship of all building components are the responsibility of thearchitect, engineer and/or building owner. The density, moisture, integrityand other inherent elements of the deck must also be suitable to receive theroof. IKO is not responsible for any of the previously mentioned and IKOshall not assume responsibility for these issues under any circumstances. WOO

D

PLANK/HEAVY TIMBER - min 1”

PLYWOOD - min 15/32”

TECHNICAL BINDER REFERENCE� 3.15 & 3.16� Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1

WOOD (CHOOSE ONE)

CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

VAPOR

RETARDERS

IKO MVP * - Is a self-adhering vapor retardant membrane. It is composed of modified rubber asphaltwith a top surface film of high density cross laminated polyethylene. This product should not be appliedat temperatures below -10°C.

ARMOURGARD VAPOR RETARDANT ** - Composed of two layers of kraft paper bonded together withasphalt. Strands of fiberglass reinforcement are intertwined near each edge for added strength and tear resistance.

2 PLY NO. 15 PERF FELT - A high strength cellulose mat that is thoroughly impregnated with asphalt.

MODIFIED ROLL - e.g. MF-95-SS-BASE, MP-180-SS-BASE.

* Requires approved self-adhering membrane primer.

** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Adhesive or hot mopped.

NOTE: No. 15 Perf Felt and sanded-base modified rolls are adhered with asphalt (hot mopped).Asphalt primer required before installation of mopped membrane.

TECHNICAL BINDER REFERENCE� 3.22, 4.081, 6.08.1, 9.08.1

VAPOR RETARDERS (CHOOSE ONE)CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

WOOD

INSULATION

IKOTHERM - Is a rigid polyisocyanurate insulation with high thermal properties. It isconstructed from a closed cell polyisocyanurate foam core bonded on each side to glassfiber reinforced facers during the manufacturing process.

NOTE: IKOTherm III with acrylic-coated facers and IKOTherm 25 psi are also available.Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.25 - 3.27, 4.11.1, 4.12.1, 6.11.1, 6.12.1

INSULATIONCAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

VAPOR RETARDERS

WOOD

COVER

BOAR

D

FIBERBOARD - Consisting of interlocking cellulose fibers bonded together by heat, pressure andpremium asphalt resin, IKO High Density Sheathing and Roofboard is produced with a high densityconstruction designed for an optimal strength-to-weight ratio and a low moisture absorption potential.In roofing applications, this product is used as an cover board over IKOTherm insulation, or as a coverboard over existing roofing systems.

PROTECTOBOARD - Is composed of a mineral-fortified asphaltic core between two non-woven glassfiber mats. Protectoboard may be used as a cover board over IKOTherm insulation, as a re-cover boardin a re-roof installation, or any other application where it is used as a new substrate for a modifiedbitumen or BUR roofing membrane.

NOTE: Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.28, 3.29, 4.15.1, 9.14.1, 9.16.1, 9.17.1

COVER BOARDCAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

INSULATION

VAPOR RETARDERS

WOOD

MEMB

RANE

CAP FLASHING

BASE FLASHING

ROOF SURFACING

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

Glass ply sheets should be hot mopped at arate of 25 lbs of asphalt per 100 sq.ft. plus orminus 20%. Organic ply sheets should be hotmopped at a rate of 20 lbs per 100 sq.ft. plusor minus 20%.

TECHNICAL BINDER REFERENCE� 3.28, 3.29, 4.15.1, 9.14.1, 9.16.1, 9.17.1

4 PLY:NO. 15 PERF FELTTYPE IV GLASSTYPE 6 GLASS

COMBINATION:1 PLY NO. 15 PERF FELT& 4 PLIES TYPE IV

MEMBRANE (CHOOSE ONE)

BASE

FLASHING

CAP FLASHINGROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

Flashings to be a maximum width of 39.5"(width of roll), installed in the machine directionand staggered a minimum of 12" from all joints.All side laps shall be 3.5".

IKO's requirements are concurrent with therecommendations of the CRCA in that 2 plypolyester reinforced flashings are desirable dueto their superior elongation and tear strength asopposed to fiberglass reinforced flashings.

TECHNICAL BINDER REFERENCE� 3.34, 4.17.1, 6.17.1 (Part 8)� 3.28 - 3.31, 3.29, 4.14.1, 4.16.1,6.14.1, 6.16.1

WITH MOP APPLIED CAP FLASHINGMP-180-SS-BASEMODIFLEX COLD GOLDTM BASE

WITH HEAT WELD APPLIED CAP FLASHINGARMOURBOND FLASH *ARMOURBOND 180 *TP-180-FF-BASEMP-180-FS-BASEAPP CLASSIC **

* Requires approved self-adhering membrane primer.** Use only with APP Classic or APP Granular cap flashing.

BASE FLASHING (CHOOSE ONE)

CAP

FLASH

ING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

MOP TO SAND TOP SURFACE BASE FLASHINGMP-180-CAPMP-250-CAPPREVENT MP-180PREVENT MP-250PREVENT PREMIUM MP-250

HEAT WELD TO FILM TOP SURFACE BASE FLASHINGTP-180-CAPTP-250-CAPTP-250-CAP (5.0)PREVENT TP- 180PREVENT TP- 250PREVENT PREMIUM TP-250APP CLASSIC*APP GRANULAR

4 PLY NO. 15 PERF FELT (FLASHING SYSTEM)

CAP FLASHING (CHOOSE ONE) Flashings to be a maximum width of 39.5" (width ofroll), installed in the machine direction and staggereda minimum of 12" from all joints. All side laps shallbe 3.5"(excluding No. 15 felt).IKO supports the recommendations of the CRCA inthat 2 ply polyester reinforced flashings are desirabledue to their superior elongation and tear strength asopposed to fiberglass reinforced flashings.* Requires approved coating applied no sooner than 30 daysand no later than 90 days after membrane application.

TECHNICAL BINDER REFERENCE� 3.34, 4.17.1, 6.17.1( Part 8, Part 11) � 3.28 - 3.31, 3.29, 4.14.1, 4.16.1, 6.14.1, 6.16.1

CI-RP-WOOD-Book9:B9 9/17/08 12:49 PM Page 3

ROOF

SURFACING

ROOF SURFACING

CAP FLASHING

BASE FLASHING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

Aggregate to be applied to a flood coat of asphalt that is applied at a rate of 60lbs/square. Aggregate to be applied at a rate of 400 lbs/square.

NOTES: A second pour and gravel can be applied after the loose gravel is swept from the roof.

TECHNICAL BINDER REFERENCE� 9.16.1

CI-RP-WOOD-Book9:B9 9/17/08 12:49 PM Page 2

COMMERCIAL & INDUSTRIAL ROOFING PRODUCTS

WOODBUR

Thank you for considering IKO Premium Roofing products.For additional information on IKO’s full line of superiorCommercial/Indudtrial Roofing and Waterproofing productsPlease call: 1-800-361-5836, or visit our web site at:

Notes:The physical properties of the products described in this cataloguerepresent averagetypical results obtained by testing our products according to accepted industry test methods.These values are subject to normal manufacturing variations, and are supplied as a technicalguideline only; they may be subject to change without notice. Current product specifications can be confirmed by contacting your local IKO technical Representative.

Also, the guide specifications contained herein are offered as general information for thedesign and installation of IKO roof assemblies. IKO Industries Limited is a supplier of materials,and we cannot assume liability for errors in roof design, engineering, or application. The architect, contractor, and/or building owner’s representative must verify all dimensions,details and suitability of roof design.

Notes:All values shown are approximate. Product and color availability subject to shippingarea. The information in this document is subject to change without notice. IKO assumes noresponsibility for errors that may appear in this document.

©Copyright 07/07 - MM3L176 - WOOD BUR - BK. 9

CI-RP-WOOD-Book9:B9 9/17/08 12:49 PM Page 1

Drainage - 3.09

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Expansion Joints - 3.21

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Cap Sheet Repair - 4.20.1, 6.20.1

NOTE: Use of the above may or may not be applicable to your specific roof.

COMMERCIAL & INDUSTRIAL ROOFING PRODUCTS

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

WOODBUR

Accessories, Options & Additional ConsiderationsTECHNICAL BINDER REFERENCE

A properly designed and constructed roof deck, as well as the properinterrelationship of all building components are the responsibility of thearchitect, engineer and/or building owner. The density, moisture, integrityand other inherent elements of the deck must also be suitable to receive theroof. IKO is not responsible for any of the previously mentioned and IKOshall not assume responsibility for these issues under any circumstances.

CI-RP-WOOD-Book9:B9 9/17/08 12:46 PM Page 10

WOOD

PLANK/HEAVY TIMBER - min 1”

PLYWOOD - min 15/32”

TECHNICAL BINDER REFERENCE� 3.15 & 3.16� Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1

WOOD (CHOOSE ONE)

CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 9

VAPOR

RETARDERS

IKO MVP * - Is a self-adhering vapor retardant membrane. It is composed of modified rubber asphalt with a top surface film of high density cross laminated polyethylene. This product should not be applied at temperatures below -10°C.

ARMOURGARD VAPOR RETARDANT ** - Composed of two layers of kraft paper bonded together withasphalt. Strands of fiberglass reinforcement are intertwined near each edge for added strength and tear resistance.

2 PLY NO. 15 PERF FELT - A high strength cellulose mat that is thoroughly impregnated with asphalt.

MODIFIED ROLL - e.g. MF-95-SS-BASE, MP-180-SS-BASE.

* Requires approved self-adhering membrane primer.

** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Adhesive or hot mopped.

NOTE: No. 15 Perf Felt and sanded-base modified rolls are adhered with asphalt (hot mopped). Asphalt primer required before installation of mopped membrane.

TECHNICAL BINDER REFERENCE� 3.22, 4.081, 6.08.1, 9.08.1

VAPOR RETARDERS (CHOOSE ONE)CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 8

INSULATION

IKOTHERM - Is a rigid polyisocyanurate insulation with high thermal properties. It is constructed from a closed cell polyisocyanurate foam core bonded on each side to glassfiber reinforced facers during the manufacturing process.

NOTE: IKOTherm III with acrylic-coated facers and IKOTherm 25 psi are also available.Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.25 - 3.27, 4.11.1, 4.12.1, 6.11.1, 6.12.1

INSULATIONCAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

VAPOR RETARDERS

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 7

COVER

BOAR

D

FIBERBOARD - Consisting of interlocking cellulose fibers bonded together by heat, pressure and premium asphalt resin, IKO High Density Sheathing and Roofboard is produced with a high density construction designed for an optimal strength-to-weight ratio and a low moisture absorption potential. In roofing applications, this product is used as an cover board over IKOTherm insulation, or as a coverboard over existing roofing systems.

PROTECTOBOARD - Is composed of a mineral-fortified asphaltic core between two non-woven glassfiber mats. Protectoboard may be used as a cover board over IKOTherm insulation, as a re-cover boardin a re-roof installation, or any other application where it is used as a new substrate for a modified bitumen or BUR roofing membrane.

NOTE: Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.28, 3.29, 4.15.1, 9.14.1, 9.16.1, 9.17.1

COVER BOARD CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

INSULATION

VAPOR RETARDERS

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 6

MEMB

RANE

CAP FLASHING

BASE FLASHING

ROOF SURFACING

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

Glass ply sheets should be hot mopped at a rate of 25 lbs of asphalt per 100 sq.ft. plus orminus 20%. Organic ply sheets should be hotmopped at a rate of 20 lbs per 100 sq.ft. plus or minus 20%.

TECHNICAL BINDER REFERENCE� 3.28, 3.29, 4.15.1, 9.14.1, 9.16.1, 9.17.1

4 PLY: NO. 15 PERF FELT TYPE IV GLASS TYPE 6 GLASS

COMBINATION: 1 PLY NO. 15 PERF FELT & 4 PLIES TYPE IV

MEMBRANE (CHOOSE ONE)

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 5

BASE

FLASHING

CAP FLASHINGROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

Flashings to be a maximum width of 39.5" (width of roll), installed in the machine directionand staggered a minimum of 12" from all joints. All side laps shall be 3.5".

IKO's requirements are concurrent with the recommendations of the CRCA in that 2 ply polyester reinforced flashings are desirable due to their superior elongation and tear strength asopposed to fiberglass reinforced flashings.

TECHNICAL BINDER REFERENCE� 3.34, 4.17.1, 6.17.1 (Part 8)� 3.28 - 3.31, 3.29, 4.14.1, 4.16.1, 6.14.1, 6.16.1

WITH MOP APPLIED CAP FLASHINGMP-180-SS-BASEMODIFLEX COLD GOLDTM BASE

WITH HEAT WELD APPLIED CAP FLASHINGARMOURBOND FLASH *ARMOURBOND 180 *TP-180-FF-BASE MP-180-FS-BASE APP CLASSIC **

* Requires approved self-adhering membrane primer.** Use only with APP Classic or APP Granular cap flashing.

BASE FLASHING (CHOOSE ONE)

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 4

CAP

FLASH

ING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

MOP TO SAND TOP SURFACE BASE FLASHINGMP-180-CAPMP-250-CAPPREVENT MP-180PREVENT MP-250PREVENT PREMIUM MP-250

HEAT WELD TO FILM TOP SURFACE BASE FLASHINGTP-180-CAPTP-250-CAPTP-250-CAP (5.0)PREVENT TP- 180PREVENT TP- 250PREVENT PREMIUM TP-250APP CLASSIC*APP GRANULAR

4 PLY NO. 15 PERF FELT (FLASHING SYSTEM)

CAP FLASHING (CHOOSE ONE) Flashings to be a maximum width of 39.5" (width ofroll), installed in the machine direction and staggered a minimum of 12" from all joints. All side laps shall be 3.5"(excluding No. 15 felt).IKO supports the recommendations of the CRCA in that 2 ply polyester reinforced flashings are desirabledue to their superior elongation and tear strength asopposed to fiberglass reinforced flashings.* Requires approved coating applied no sooner than 30 daysand no later than 90 days after membrane application.

TECHNICAL BINDER REFERENCE� 3.34, 4.17.1, 6.17.1( Part 8, Part 11) � 3.28 - 3.31, 3.29, 4.14.1, 4.16.1, 6.14.1, 6.16.1

CI-RP-WOOD-Book9:B9 9/17/08 12:49 PM Page 3

ROOF

SURFACING

ROOF SURFACING

CAP FLASHING

BASE FLASHING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

Aggregate to be applied to a flood coat of asphalt that is applied at a rate of 60lbs/square. Aggregate to be applied at a rate of 400 lbs/square.

NOTES: A second pour and gravel can be applied after the loose gravel is swept from the roof.

TECHNICAL BINDER REFERENCE� 9.16.1

CI-RP-WOOD-Book9:B9 9/17/08 12:49 PM Page 2

Drainage - 3.09

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Expansion Joints - 3.21

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Cap Sheet Repair - 4.20.1, 6.20.1

NOTE: Use of the above may or may not be applicable to your specific roof.

COMMERCIAL & INDUSTRIAL ROOFING PRODUCTS

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

WOODBUR

Accessories, Options & Additional ConsiderationsTECHNICAL BINDER REFERENCE

A properly designed and constructed roof deck, as well as the properinterrelationship of all building components are the responsibility of thearchitect, engineer and/or building owner. The density, moisture, integrityand other inherent elements of the deck must also be suitable to receive theroof. IKO is not responsible for any of the previously mentioned and IKOshall not assume responsibility for these issues under any circumstances.

CI-RP-WOOD-Book9:B9 9/17/08 12:46 PM Page 10

WOOD

PLANK/HEAVY TIMBER - min 1”

PLYWOOD - min 15/32”

TECHNICAL BINDER REFERENCE� 3.15 & 3.16� Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1

WOOD (CHOOSE ONE)

CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 9

VAPOR

RETARDERS

IKO MVP * - Is a self-adhering vapor retardant membrane. It is composed of modified rubber asphalt with a top surface film of high density cross laminated polyethylene. This product should not be applied at temperatures below -10°C.

ARMOURGARD VAPOR RETARDANT ** - Composed of two layers of kraft paper bonded together withasphalt. Strands of fiberglass reinforcement are intertwined near each edge for added strength and tear resistance.

2 PLY NO. 15 PERF FELT - A high strength cellulose mat that is thoroughly impregnated with asphalt.

MODIFIED ROLL - e.g. MF-95-SS-BASE, MP-180-SS-BASE.

* Requires approved self-adhering membrane primer.

** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Adhesive or hot mopped.

NOTE: No. 15 Perf Felt and sanded-base modified rolls are adhered with asphalt (hot mopped). Asphalt primer required before installation of mopped membrane.

TECHNICAL BINDER REFERENCE� 3.22, 4.081, 6.08.1, 9.08.1

VAPOR RETARDERS (CHOOSE ONE)CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 8

INSULATION

IKOTHERM - Is a rigid polyisocyanurate insulation with high thermal properties. It is constructed from a closed cell polyisocyanurate foam core bonded on each side to glassfiber reinforced facers during the manufacturing process.

NOTE: IKOTherm III with acrylic-coated facers and IKOTherm 25 psi are also available.Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.25 - 3.27, 4.11.1, 4.12.1, 6.11.1, 6.12.1

INSULATIONCAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

VAPOR RETARDERS

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 7

COVER

BOAR

D

FIBERBOARD - Consisting of interlocking cellulose fibers bonded together by heat, pressure and premium asphalt resin, IKO High Density Sheathing and Roofboard is produced with a high density construction designed for an optimal strength-to-weight ratio and a low moisture absorption potential. In roofing applications, this product is used as an cover board over IKOTherm insulation, or as a coverboard over existing roofing systems.

PROTECTOBOARD - Is composed of a mineral-fortified asphaltic core between two non-woven glassfiber mats. Protectoboard may be used as a cover board over IKOTherm insulation, as a re-cover boardin a re-roof installation, or any other application where it is used as a new substrate for a modified bitumen or BUR roofing membrane.

NOTE: Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.28, 3.29, 4.15.1, 9.14.1, 9.16.1, 9.17.1

COVER BOARD CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

INSULATION

VAPOR RETARDERS

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 6

MEMB

RANE

CAP FLASHING

BASE FLASHING

ROOF SURFACING

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

Glass ply sheets should be hot mopped at a rate of 25 lbs of asphalt per 100 sq.ft. plus orminus 20%. Organic ply sheets should be hotmopped at a rate of 20 lbs per 100 sq.ft. plus or minus 20%.

TECHNICAL BINDER REFERENCE� 3.28, 3.29, 4.15.1, 9.14.1, 9.16.1, 9.17.1

4 PLY: NO. 15 PERF FELT TYPE IV GLASS TYPE 6 GLASS

COMBINATION: 1 PLY NO. 15 PERF FELT & 4 PLIES TYPE IV

MEMBRANE (CHOOSE ONE)

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 5

BASE

FLASHING

CAP FLASHINGROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

Flashings to be a maximum width of 39.5" (width of roll), installed in the machine directionand staggered a minimum of 12" from all joints. All side laps shall be 3.5".

IKO's requirements are concurrent with the recommendations of the CRCA in that 2 ply polyester reinforced flashings are desirable due to their superior elongation and tear strength asopposed to fiberglass reinforced flashings.

TECHNICAL BINDER REFERENCE� 3.34, 4.17.1, 6.17.1 (Part 8)� 3.28 - 3.31, 3.29, 4.14.1, 4.16.1, 6.14.1, 6.16.1

WITH MOP APPLIED CAP FLASHINGMP-180-SS-BASEMODIFLEX COLD GOLDTM BASE

WITH HEAT WELD APPLIED CAP FLASHINGARMOURBOND FLASH *ARMOURBOND 180 *TP-180-FF-BASE MP-180-FS-BASE APP CLASSIC **

* Requires approved self-adhering membrane primer.** Use only with APP Classic or APP Granular cap flashing.

BASE FLASHING (CHOOSE ONE)

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 4

CAP

FLASH

ING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

MOP TO SAND TOP SURFACE BASE FLASHINGMP-180-CAPMP-250-CAPPREVENT MP-180PREVENT MP-250PREVENT PREMIUM MP-250

HEAT WELD TO FILM TOP SURFACE BASE FLASHINGTP-180-CAPTP-250-CAPTP-250-CAP (5.0)PREVENT TP- 180PREVENT TP- 250PREVENT PREMIUM TP-250APP CLASSIC*APP GRANULAR

4 PLY NO. 15 PERF FELT (FLASHING SYSTEM)

CAP FLASHING (CHOOSE ONE) Flashings to be a maximum width of 39.5" (width ofroll), installed in the machine direction and staggered a minimum of 12" from all joints. All side laps shall be 3.5"(excluding No. 15 felt).IKO supports the recommendations of the CRCA in that 2 ply polyester reinforced flashings are desirabledue to their superior elongation and tear strength asopposed to fiberglass reinforced flashings.* Requires approved coating applied no sooner than 30 daysand no later than 90 days after membrane application.

TECHNICAL BINDER REFERENCE� 3.34, 4.17.1, 6.17.1( Part 8, Part 11) � 3.28 - 3.31, 3.29, 4.14.1, 4.16.1, 6.14.1, 6.16.1

CI-RP-WOOD-Book9:B9 9/17/08 12:49 PM Page 3

Drainage - 3.09

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Expansion Joints - 3.21

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Cap Sheet Repair - 4.20.1, 6.20.1

NOTE: Use of the above may or may not be applicable to your specific roof.

COMMERCIAL & INDUSTRIAL ROOFING PRODUCTS

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

WOODBUR

Accessories, Options & Additional ConsiderationsTECHNICAL BINDER REFERENCE

A properly designed and constructed roof deck, as well as the properinterrelationship of all building components are the responsibility of thearchitect, engineer and/or building owner. The density, moisture, integrityand other inherent elements of the deck must also be suitable to receive theroof. IKO is not responsible for any of the previously mentioned and IKOshall not assume responsibility for these issues under any circumstances.

CI-RP-WOOD-Book9:B9 9/17/08 12:46 PM Page 10

WOOD

PLANK/HEAVY TIMBER - min 1”

PLYWOOD - min 15/32”

TECHNICAL BINDER REFERENCE� 3.15 & 3.16� Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1

WOOD (CHOOSE ONE)

CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 9

VAPOR

RETARDERS

IKO MVP * - Is a self-adhering vapor retardant membrane. It is composed of modified rubber asphalt with a top surface film of high density cross laminated polyethylene. This product should not be applied at temperatures below -10°C.

ARMOURGARD VAPOR RETARDANT ** - Composed of two layers of kraft paper bonded together withasphalt. Strands of fiberglass reinforcement are intertwined near each edge for added strength and tear resistance.

2 PLY NO. 15 PERF FELT - A high strength cellulose mat that is thoroughly impregnated with asphalt.

MODIFIED ROLL - e.g. MF-95-SS-BASE, MP-180-SS-BASE.

* Requires approved self-adhering membrane primer.

** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Adhesive or hot mopped.

NOTE: No. 15 Perf Felt and sanded-base modified rolls are adhered with asphalt (hot mopped). Asphalt primer required before installation of mopped membrane.

TECHNICAL BINDER REFERENCE� 3.22, 4.081, 6.08.1, 9.08.1

VAPOR RETARDERS (CHOOSE ONE)CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 8

INSULATION

IKOTHERM - Is a rigid polyisocyanurate insulation with high thermal properties. It is constructed from a closed cell polyisocyanurate foam core bonded on each side to glassfiber reinforced facers during the manufacturing process.

NOTE: IKOTherm III with acrylic-coated facers and IKOTherm 25 psi are also available.Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.25 - 3.27, 4.11.1, 4.12.1, 6.11.1, 6.12.1

INSULATIONCAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

VAPOR RETARDERS

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 7

COVER

BOAR

D

FIBERBOARD - Consisting of interlocking cellulose fibers bonded together by heat, pressure and premium asphalt resin, IKO High Density Sheathing and Roofboard is produced with a high density construction designed for an optimal strength-to-weight ratio and a low moisture absorption potential. In roofing applications, this product is used as an cover board over IKOTherm insulation, or as a coverboard over existing roofing systems.

PROTECTOBOARD - Is composed of a mineral-fortified asphaltic core between two non-woven glassfiber mats. Protectoboard may be used as a cover board over IKOTherm insulation, as a re-cover boardin a re-roof installation, or any other application where it is used as a new substrate for a modified bitumen or BUR roofing membrane.

NOTE: Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.28, 3.29, 4.15.1, 9.14.1, 9.16.1, 9.17.1

COVER BOARD CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

INSULATION

VAPOR RETARDERS

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 6

MEMB

RANE

CAP FLASHING

BASE FLASHING

ROOF SURFACING

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

Glass ply sheets should be hot mopped at a rate of 25 lbs of asphalt per 100 sq.ft. plus orminus 20%. Organic ply sheets should be hotmopped at a rate of 20 lbs per 100 sq.ft. plus or minus 20%.

TECHNICAL BINDER REFERENCE� 3.28, 3.29, 4.15.1, 9.14.1, 9.16.1, 9.17.1

4 PLY: NO. 15 PERF FELT TYPE IV GLASS TYPE 6 GLASS

COMBINATION: 1 PLY NO. 15 PERF FELT & 4 PLIES TYPE IV

MEMBRANE (CHOOSE ONE)

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 5

BASE

FLASHING

CAP FLASHINGROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

Flashings to be a maximum width of 39.5" (width of roll), installed in the machine directionand staggered a minimum of 12" from all joints. All side laps shall be 3.5".

IKO's requirements are concurrent with the recommendations of the CRCA in that 2 ply polyester reinforced flashings are desirable due to their superior elongation and tear strength asopposed to fiberglass reinforced flashings.

TECHNICAL BINDER REFERENCE� 3.34, 4.17.1, 6.17.1 (Part 8)� 3.28 - 3.31, 3.29, 4.14.1, 4.16.1, 6.14.1, 6.16.1

WITH MOP APPLIED CAP FLASHINGMP-180-SS-BASEMODIFLEX COLD GOLDTM BASE

WITH HEAT WELD APPLIED CAP FLASHINGARMOURBOND FLASH *ARMOURBOND 180 *TP-180-FF-BASE MP-180-FS-BASE APP CLASSIC **

* Requires approved self-adhering membrane primer.** Use only with APP Classic or APP Granular cap flashing.

BASE FLASHING (CHOOSE ONE)

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 4

Drainage - 3.09

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Expansion Joints - 3.21

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Cap Sheet Repair - 4.20.1, 6.20.1

NOTE: Use of the above may or may not be applicable to your specific roof.

COMMERCIAL & INDUSTRIAL ROOFING PRODUCTS

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

WOODBUR

Accessories, Options & Additional ConsiderationsTECHNICAL BINDER REFERENCE

A properly designed and constructed roof deck, as well as the properinterrelationship of all building components are the responsibility of thearchitect, engineer and/or building owner. The density, moisture, integrityand other inherent elements of the deck must also be suitable to receive theroof. IKO is not responsible for any of the previously mentioned and IKOshall not assume responsibility for these issues under any circumstances.

CI-RP-WOOD-Book9:B9 9/17/08 12:46 PM Page 10

WOOD

PLANK/HEAVY TIMBER - min 1”

PLYWOOD - min 15/32”

TECHNICAL BINDER REFERENCE� 3.15 & 3.16� Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1

WOOD (CHOOSE ONE)

CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 9

VAPOR

RETARDERS

IKO MVP * - Is a self-adhering vapor retardant membrane. It is composed of modified rubber asphalt with a top surface film of high density cross laminated polyethylene. This product should not be applied at temperatures below -10°C.

ARMOURGARD VAPOR RETARDANT ** - Composed of two layers of kraft paper bonded together withasphalt. Strands of fiberglass reinforcement are intertwined near each edge for added strength and tear resistance.

2 PLY NO. 15 PERF FELT - A high strength cellulose mat that is thoroughly impregnated with asphalt.

MODIFIED ROLL - e.g. MF-95-SS-BASE, MP-180-SS-BASE.

* Requires approved self-adhering membrane primer.

** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Adhesive or hot mopped.

NOTE: No. 15 Perf Felt and sanded-base modified rolls are adhered with asphalt (hot mopped). Asphalt primer required before installation of mopped membrane.

TECHNICAL BINDER REFERENCE� 3.22, 4.081, 6.08.1, 9.08.1

VAPOR RETARDERS (CHOOSE ONE)CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 8

INSULATION

IKOTHERM - Is a rigid polyisocyanurate insulation with high thermal properties. It is constructed from a closed cell polyisocyanurate foam core bonded on each side to glassfiber reinforced facers during the manufacturing process.

NOTE: IKOTherm III with acrylic-coated facers and IKOTherm 25 psi are also available.Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.25 - 3.27, 4.11.1, 4.12.1, 6.11.1, 6.12.1

INSULATIONCAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

VAPOR RETARDERS

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 7

COVER

BOAR

D

FIBERBOARD - Consisting of interlocking cellulose fibers bonded together by heat, pressure and premium asphalt resin, IKO High Density Sheathing and Roofboard is produced with a high density construction designed for an optimal strength-to-weight ratio and a low moisture absorption potential. In roofing applications, this product is used as an cover board over IKOTherm insulation, or as a coverboard over existing roofing systems.

PROTECTOBOARD - Is composed of a mineral-fortified asphaltic core between two non-woven glassfiber mats. Protectoboard may be used as a cover board over IKOTherm insulation, as a re-cover boardin a re-roof installation, or any other application where it is used as a new substrate for a modified bitumen or BUR roofing membrane.

NOTE: Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.28, 3.29, 4.15.1, 9.14.1, 9.16.1, 9.17.1

COVER BOARD CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

INSULATION

VAPOR RETARDERS

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 6

MEMB

RANE

CAP FLASHING

BASE FLASHING

ROOF SURFACING

COVER BOARD

INSULATION

VAPOR RETARDERS

WOOD

Glass ply sheets should be hot mopped at a rate of 25 lbs of asphalt per 100 sq.ft. plus orminus 20%. Organic ply sheets should be hotmopped at a rate of 20 lbs per 100 sq.ft. plus or minus 20%.

TECHNICAL BINDER REFERENCE� 3.28, 3.29, 4.15.1, 9.14.1, 9.16.1, 9.17.1

4 PLY: NO. 15 PERF FELT TYPE IV GLASS TYPE 6 GLASS

COMBINATION: 1 PLY NO. 15 PERF FELT & 4 PLIES TYPE IV

MEMBRANE (CHOOSE ONE)

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 5

Drainage - 3.09

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Expansion Joints - 3.21

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Cap Sheet Repair - 4.20.1, 6.20.1

NOTE: Use of the above may or may not be applicable to your specific roof.

COMMERCIAL & INDUSTRIAL ROOFING PRODUCTS

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

WOODBUR

Accessories, Options & Additional ConsiderationsTECHNICAL BINDER REFERENCE

A properly designed and constructed roof deck, as well as the properinterrelationship of all building components are the responsibility of thearchitect, engineer and/or building owner. The density, moisture, integrityand other inherent elements of the deck must also be suitable to receive theroof. IKO is not responsible for any of the previously mentioned and IKOshall not assume responsibility for these issues under any circumstances.

CI-RP-WOOD-Book9:B9 9/17/08 12:46 PM Page 10

WOOD

PLANK/HEAVY TIMBER - min 1”

PLYWOOD - min 15/32”

TECHNICAL BINDER REFERENCE� 3.15 & 3.16� Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1

WOOD (CHOOSE ONE)

CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 9

VAPOR

RETARDERS

IKO MVP * - Is a self-adhering vapor retardant membrane. It is composed of modified rubber asphalt with a top surface film of high density cross laminated polyethylene. This product should not be applied at temperatures below -10°C.

ARMOURGARD VAPOR RETARDANT ** - Composed of two layers of kraft paper bonded together withasphalt. Strands of fiberglass reinforcement are intertwined near each edge for added strength and tear resistance.

2 PLY NO. 15 PERF FELT - A high strength cellulose mat that is thoroughly impregnated with asphalt.

MODIFIED ROLL - e.g. MF-95-SS-BASE, MP-180-SS-BASE.

* Requires approved self-adhering membrane primer.

** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Adhesive or hot mopped.

NOTE: No. 15 Perf Felt and sanded-base modified rolls are adhered with asphalt (hot mopped). Asphalt primer required before installation of mopped membrane.

TECHNICAL BINDER REFERENCE� 3.22, 4.081, 6.08.1, 9.08.1

VAPOR RETARDERS (CHOOSE ONE)CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 8

INSULATION

IKOTHERM - Is a rigid polyisocyanurate insulation with high thermal properties. It is constructed from a closed cell polyisocyanurate foam core bonded on each side to glassfiber reinforced facers during the manufacturing process.

NOTE: IKOTherm III with acrylic-coated facers and IKOTherm 25 psi are also available.Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.25 - 3.27, 4.11.1, 4.12.1, 6.11.1, 6.12.1

INSULATIONCAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

VAPOR RETARDERS

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 7

COVER

BOAR

D

FIBERBOARD - Consisting of interlocking cellulose fibers bonded together by heat, pressure and premium asphalt resin, IKO High Density Sheathing and Roofboard is produced with a high density construction designed for an optimal strength-to-weight ratio and a low moisture absorption potential. In roofing applications, this product is used as an cover board over IKOTherm insulation, or as a coverboard over existing roofing systems.

PROTECTOBOARD - Is composed of a mineral-fortified asphaltic core between two non-woven glassfiber mats. Protectoboard may be used as a cover board over IKOTherm insulation, as a re-cover boardin a re-roof installation, or any other application where it is used as a new substrate for a modified bitumen or BUR roofing membrane.

NOTE: Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.28, 3.29, 4.15.1, 9.14.1, 9.16.1, 9.17.1

COVER BOARD CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

INSULATION

VAPOR RETARDERS

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:48 PM Page 6

Drainage - 3.09

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Expansion Joints - 3.21

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Cap Sheet Repair - 4.20.1, 6.20.1

NOTE: Use of the above may or may not be applicable to your specific roof.

COMMERCIAL & INDUSTRIAL ROOFING PRODUCTS

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

WOODBUR

Accessories, Options & Additional ConsiderationsTECHNICAL BINDER REFERENCE

A properly designed and constructed roof deck, as well as the properinterrelationship of all building components are the responsibility of thearchitect, engineer and/or building owner. The density, moisture, integrityand other inherent elements of the deck must also be suitable to receive theroof. IKO is not responsible for any of the previously mentioned and IKOshall not assume responsibility for these issues under any circumstances.

CI-RP-WOOD-Book9:B9 9/17/08 12:46 PM Page 10

WOOD

PLANK/HEAVY TIMBER - min 1”

PLYWOOD - min 15/32”

TECHNICAL BINDER REFERENCE� 3.15 & 3.16� Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1

WOOD (CHOOSE ONE)

CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 9

VAPOR

RETARDERS

IKO MVP * - Is a self-adhering vapor retardant membrane. It is composed of modified rubber asphalt with a top surface film of high density cross laminated polyethylene. This product should not be applied at temperatures below -10°C.

ARMOURGARD VAPOR RETARDANT ** - Composed of two layers of kraft paper bonded together withasphalt. Strands of fiberglass reinforcement are intertwined near each edge for added strength and tear resistance.

2 PLY NO. 15 PERF FELT - A high strength cellulose mat that is thoroughly impregnated with asphalt.

MODIFIED ROLL - e.g. MF-95-SS-BASE, MP-180-SS-BASE.

* Requires approved self-adhering membrane primer.

** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Adhesive or hot mopped.

NOTE: No. 15 Perf Felt and sanded-base modified rolls are adhered with asphalt (hot mopped). Asphalt primer required before installation of mopped membrane.

TECHNICAL BINDER REFERENCE� 3.22, 4.081, 6.08.1, 9.08.1

VAPOR RETARDERS (CHOOSE ONE)CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 8

INSULATION

IKOTHERM - Is a rigid polyisocyanurate insulation with high thermal properties. It is constructed from a closed cell polyisocyanurate foam core bonded on each side to glassfiber reinforced facers during the manufacturing process.

NOTE: IKOTherm III with acrylic-coated facers and IKOTherm 25 psi are also available.Can be mechanically attached, cold applied or hot mopped.

TECHNICAL BINDER REFERENCE� 3.25 - 3.27, 4.11.1, 4.12.1, 6.11.1, 6.12.1

INSULATIONCAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

VAPOR RETARDERS

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 7

Drainage - 3.09

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Expansion Joints - 3.21

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Cap Sheet Repair - 4.20.1, 6.20.1

NOTE: Use of the above may or may not be applicable to your specific roof.

COMMERCIAL & INDUSTRIAL ROOFING PRODUCTS

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

WOODBUR

Accessories, Options & Additional ConsiderationsTECHNICAL BINDER REFERENCE

A properly designed and constructed roof deck, as well as the properinterrelationship of all building components are the responsibility of thearchitect, engineer and/or building owner. The density, moisture, integrityand other inherent elements of the deck must also be suitable to receive theroof. IKO is not responsible for any of the previously mentioned and IKOshall not assume responsibility for these issues under any circumstances.

CI-RP-WOOD-Book9:B9 9/17/08 12:46 PM Page 10

WOOD

PLANK/HEAVY TIMBER - min 1”

PLYWOOD - min 15/32”

TECHNICAL BINDER REFERENCE� 3.15 & 3.16� Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1

WOOD (CHOOSE ONE)

CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 9

VAPOR

RETARDERS

IKO MVP * - Is a self-adhering vapor retardant membrane. It is composed of modified rubber asphalt with a top surface film of high density cross laminated polyethylene. This product should not be applied at temperatures below -10°C.

ARMOURGARD VAPOR RETARDANT ** - Composed of two layers of kraft paper bonded together withasphalt. Strands of fiberglass reinforcement are intertwined near each edge for added strength and tear resistance.

2 PLY NO. 15 PERF FELT - A high strength cellulose mat that is thoroughly impregnated with asphalt.

MODIFIED ROLL - e.g. MF-95-SS-BASE, MP-180-SS-BASE.

* Requires approved self-adhering membrane primer.

** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Adhesive or hot mopped.

NOTE: No. 15 Perf Felt and sanded-base modified rolls are adhered with asphalt (hot mopped). Asphalt primer required before installation of mopped membrane.

TECHNICAL BINDER REFERENCE� 3.22, 4.081, 6.08.1, 9.08.1

VAPOR RETARDERS (CHOOSE ONE)CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

WOOD

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 8

Drainage - 3.09

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Expansion Joints - 3.21

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Cap Sheet Repair - 4.20.1, 6.20.1

NOTE: Use of the above may or may not be applicable to your specific roof.

COMMERCIAL & INDUSTRIAL ROOFING PRODUCTS

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

WOODBUR

Accessories, Options & Additional ConsiderationsTECHNICAL BINDER REFERENCE

A properly designed and constructed roof deck, as well as the properinterrelationship of all building components are the responsibility of thearchitect, engineer and/or building owner. The density, moisture, integrityand other inherent elements of the deck must also be suitable to receive theroof. IKO is not responsible for any of the previously mentioned and IKOshall not assume responsibility for these issues under any circumstances.

CI-RP-WOOD-Book9:B9 9/17/08 12:46 PM Page 10

WOOD

PLANK/HEAVY TIMBER - min 1”

PLYWOOD - min 15/32”

TECHNICAL BINDER REFERENCE� 3.15 & 3.16� Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1

WOOD (CHOOSE ONE)

CAP FLASHING

BASE FLASHING

ROOF SURFACING

MEMBRANE

COVER BOARD

INSULATION

VAPOR RETARDERS

CI-RP-WOOD-Book9:B9 9/17/08 12:47 PM Page 9

Drainage - 3.09

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Expansion Joints - 3.21

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Cap Sheet Repair - 4.20.1, 6.20.1

NOTE: Use of the above may or may not be applicable to your specific roof.

COMMERCIAL & INDUSTRIAL ROOFING PRODUCTS

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

WOODBUR

Accessories, Options & Additional ConsiderationsTECHNICAL BINDER REFERENCE

A properly designed and constructed roof deck, as well as the properinterrelationship of all building components are the responsibility of thearchitect, engineer and/or building owner. The density, moisture, integrityand other inherent elements of the deck must also be suitable to receive theroof. IKO is not responsible for any of the previously mentioned and IKOshall not assume responsibility for these issues under any circumstances.

CI-RP-WOOD-Book9:B9 9/17/08 12:46 PM Page 10

COMMERCIAL&INDUSTRIAL ROOFING PRODUCTS

WOODBUR

Thank you for considering IKO Premium Roofing products.For additional information on IKO’s full line of superiorCommercial/Indudtrial Roofing and Waterproofing productsPlease call: 1-800-361-5836, or visit our web site at:

Notes: The physical properties of the products described in this catalogue represent averagetypical results obtained by testing our products according to accepted industry test methods.These values are subject to normal manufacturing variations, and are supplied as a technicalguideline only; they may be subject to change without notice. Current product specifications can be confirmed by contacting your local IKO technical Representative.

Also, the guide specifications contained herein are offered as general information for thedesign and installation of IKO roof assemblies. IKO Industries Limited is a supplier of materials,and we cannot assume liability for errors in roof design, engineering, or application. The architect, contractor, and/or building owner’s representative must verify all dimensions,details and suitability of roof design.

Notes: All values shown are approximate. Product and color availability subject to shippingarea. The information in this document is subject to change without notice. IKO assumes noresponsibility for errors that may appear in this document.

© Copyright 07/07 - MM3L176 - WOOD BUR - BK. 9

CI-RP-WOOD-Book9:B9 9/17/08 12:49 PM Page 1