chassis fl10.5 service manual - encompass · pdf filelcd tv chassis fl10.5 service manual ......

LCD TVchassis FL10.5

SERVICE MANUALContents

40” 40MF430B/F7 MAGNAVOX (Serial No. : DS1A)

40” 40MF430B/F7 MAGNAVOX (Serial No. : DS2A)

40” LC407SS1 SYLVANIA (Serial No. : DS1A)



40” LC407EM1 EMERSON

© 2010 Funai Electric Co., Ltd.

All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.

with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.

A01PBUH/PEUH/P1UH/PDUH/PFUH/P4UH100722

IMPORTANT SAFETY NOTICE

Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen.

TABLE OF CONTENTS

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1

1-1 FL10.5SP

SPECIFICATIONS

< TUNER / NTSC >ANT. Input ---------------------- 75 Ω Unbal., F type

< TUNER / ATSC >

< LCD PANEL >

< VIDEO >

< AUDIO >

All items are measured across 8 Ω load at speaker output terminal with L.P.F.

Description Condition Unit Nominal Limit

1. AFT Pull-In Range --- MHz ±2.3 ±2.1

2. Synchronizing Sens.TV.ch.4

CA.ch.31CA.ch.87

dBµdBµdBµ

181818

202023


1. Received Freq. Range (-28dBm) --- kHz --- ±100

2. ATSC Dynamic Range (min / max)ch.4ch.10ch.41

dBmdBmdBm

---------

-76/0-76/0

-76/+4


1. Native Pixel Resolution HorizontalVertical

pixelspixels

19201080

------

2. Brightness (w / filter) --- cd/m2 400 ---

3. Viewing Angle HorizontalVertical

°°

-88 to 88-88 to 88

-70 to 70-70 to 70


1. Over Scan HorizontalVertical

%%

55

5±55±5

2. Color Temperature---xy

°K 120000.2720.278

---±3%±3%

3. Resolution (composite video) HorizontalVertical

lineline

400350

------


1. Audio Output 10% Distortion (ATSC 0 dBfs) Lch/Rch W 10.0/10.0 8.0/8.0

2. Audio Distortion (NTSC) 500mW: Lch/Rch % 0.5/0.5 2.0/2.0

3. Audio Freq. Response (NTSC) -6dB: Lch-6dB: Rch

HzHz

70 to 10 k70 to 10 k

100 to 8 k100 to 8 k

2-1 LTVN_ISP

IMPORTANT SAFETY PRECAUTIONS

Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

Safety Precautions for LCD TV Circuit1. Before returning an instrument to the

customer, always make a safety check of the entire instrument, including, but not limited to, the following items:

a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage.

b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover.

c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position.

d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test.

ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES.

2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel.

ALSO TEST WITHPLUG REVERSEDUSING ACADAPTER PLUGAS REQUIRED

TEST ALL EXPOSEDMETAL SURFACES

READING SHOULD NOT BE ABOVE 0.5 mA

EARTHGROUND

_

DEVICELEAKAGECURRENT

TESTER

+BEINGTESTED

2-2 LTVN_ISP

3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom.

4. Hot Chassis Warning -

a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground.

b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection.

c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered.

5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage.

6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.

7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

2-3 LTVN_ISP

Precautions during ServicingA. Parts identified by the # symbol are critical for

safety.Replace only with part number specified.

B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.

C. Use specified internal wiring. Note especially:

1) Wires covered with PVC tubing

2) Double insulated wires

3) High voltage leads

D. Use specified insulating materials for hazardous live parts. Note especially:

1) Insulation Tape

2) PVC tubing

3) Spacers

4) Insulators for transistors.

E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.

F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.)

G. Check that replaced wires do not contact sharp edged or pointed parts.

H. When a power cord has been replaced, check that 5~6 kg of force in any direction will not loosen it.

I. Also check areas surrounding repaired locations.

J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set.

K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet.

L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly.

2-4 LTVN_ISP

Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.

1. Clearance Distance

When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)

Table 1: Ratings for selected area

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

2. Leakage Current Test

Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.

Measuring Method: (Power ON)

Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.

Table 2: Leakage current ratings for selected areas

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

AC Line Voltage Region Clearance Distance (d), (d’)

110 to 130 V U.S.A. or Canada

≥ 3.2 mm (0.126 inches)

AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:

110 to 130 V U.S.A. or Canada

0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA rms Exposed accessible

parts

Chassis or Secondary Conductor

Primary Circuit

Fig. 1

d' d

AC Voltmeter (High Impedance)

Exposed Accessible Part

B Earth Ground Power Cord Plug Prongs

Z

Fig. 2

3-1 TVN_SN

STANDARD NOTES FOR SERVICING

Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is

indicated as shown.

2. For other ICs, pin 1 and every fifth pin are indicated as shown.

3. The 1st pin of every male connector is indicated as shown.

Pb (Lead) Free SolderPb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder.

How to Remove / Install Flat Pack-IC

1. Removal

With Hot-Air Flat Pack-IC Desoldering Machine:

1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)

2. Remove the flat pack-IC with tweezers while applying the hot air.

3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

CAUTION:

1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.

2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)

Top View

Out In

Bottom ViewInput

5

10

Pin 1

Pin 1

Pb free mark

Fig. S-1-1

3-2 TVN_SN

3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.

With Soldering Iron:

1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)



Hot-airFlat Pack-ICDesolderingMachine

CBA

Flat Pack-IC

Tweezers

Masking Tape

Fig. S-1-2

Flat Pack-IC Desoldering Braid

Soldering Iron

Fig. S-1-3

Fine TipSoldering Iron

SharpPin

Fig. S-1-4

3-3 TVN_SN

With Iron Wire:

1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.

3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.



Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.

2. Installation1. Using desoldering braid, remove the solder from

the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.

2. The “ I ” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)

3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.

To Solid Mounting Point

Soldering Iron

Iron Wire

or

Hot Air Blower

Fig. S-1-5

Fine TipSoldering IronCBA

Flat Pack-ICTweezers

Fig. S-1-6

Example :

Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7

Presolder

CBA

Flat Pack-IC

Fig. S-1-8

3-4 TVN_SN

Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.

1. Ground for Human Body

Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

2. Ground for Workbench

Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.

<Incorrect>

CBA

Grounding Band

Conductive Sheet orCopper Plate

1MΩ

1MΩ

<Correct>

CBA

4-1 FL10.5DC

CABINET DISASSEMBLY INSTRUCTIONS[40MF430B/F7 (Serial No. : DS1A),

LC407SS1 (Serial No. : DS1A, DS2A), LC407EM1]

1. Disassembly FlowchartThis flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.

2. Disassembly Method

Step/Loc. No.

Part

Removal

Fig. No.

Remove/*Unhook/Unlock/Release/Unplug/Unclamp/

Desolder

Note

[1] Stand Assembly D1 4(S-1), 2(S-2) ---

[2] Rear Cabinet D1 20(S-3), 2(S-4),

5(S-5), (S-6) ---

[3] Speaker Holder

D2D5

4(S-7), *CN2801, *CN2802 ---

[4] Speaker D2 --------------- ---

[1] StandAssembly

[2] Rear Cabinet

[9] Power SupplyCBA

[4] Speaker

[3] SpeakerHolder

[15] AC InletHolder

[16] StandBracket

[12] Jack Holder (D)

[10] Jack Holder(A)

[17] PCB Holder(D), (U)

[18] Wall Mount Bracket (L), (R)

[13] Digital MainCBA Unit

[11] Jack CBA

[14] Jack PCBHolder

[19] LCD ModuleAssembly

[20] FrontCabinet

[6] IR SensorCBA

[5] Junction-ACBA

[8] Junction-BCBA

[7] FunctionCBA

[5] Junction-A CBA

D2D5 *CN2104, *WH2153 ---

[6] IR Sensor CBA

D2D5 (S-8), *WH2152 ---

[7] Function CBA

D2D5 --------------- ---

[8] Junction-B CBA

D3D5 *CN1802, *WH2101 ---

[9] Power Supply CBA

D3D5

9(S-9), *CN1601, *CN1801, *CN1914 ---

[10] Jack Holder(A) D3 (S-10) ---

[11] Jack CBA D3D5

5(S-11), *CN2102, *CN2103 ---

[12] Jack Holder(D) D3 (S-12) ---

[13] Digital Main CBA Unit

D3D5

6(S-13), 4(S-14), *CN3901, Shield Box(Z)

---

[14] Jack PCB Holder D4 2(S-15), (S-16) ---

[15] AC Inlet Holder D4 2(S-17) ---

[16] Stand Bracket D4 4(S-18), 4(S-19) ---

[17] PCB Holder(D), (U) D4 6(S-20) ---

[18]Wall Mount Bracket(L), (R)

D4 4(S-21) ---

[19]LCD Module Assembly

D4 2(S-22) ---

[20] Front Cabinet D4 --------------- ---

↓(1)

↓(2)

↓(3)

↓(4)

↓(5)

Step/Loc. No.

Part

Removal

Fig. No.


Desolder

Note

4-2 FL10.5DC

Note:(1) Order of steps in procedure. When reassembling,

follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures.

(2) Parts to be removed or installed.(3) Fig. No. showing procedure of part location

(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connector* = Unhook, Unlock, Release, Unplug, or Desoldere.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)

(5) Refer to the following "Reference Notes in the Table."

[2] Rear Cabinet

[1] Stand Assembly

(S-1)(S-2)

(S-1)

(S-3)

(S-3)

(S-3)

(S-6)

(S-4)

(S-5)

(S-3)

(S-3)

(S-2)

(S-3)

Fig. D1

4-3 FL10.5DC

(S-7)

(S-8)

(S-7)

[6] IR Sensor CBA

[7] Function CBA

[5] Junction-ACBA

[3] Speaker Holder

[3] Speaker Holder

[4] Speaker

[4] Speaker

Fig. D2

4-4 FL10.5DC

(S-10)

(S-11)

(S-12)

[12] Jack Holder(D)

[10] JackHolder(A)[9] Power Supply CBA

[8] Junction-B CBA


[11] Jack CBA

Shield Box (Z)

(S-9)

(S-9)

(S-13)

(S-13)(S-14)

Fig. D3

4-5 FL10.5DC

(S-17)

(S-18)

(S-20)

(S-20)

(S-19)

(S-21)

(S-22)

(S-15)

(S-16)

[15] AC InletHolder

[17] PCB Holder(U)

[17] PCB Holder(D)

[14] Jack PCB Holder

[16] Stand Bracket[18] Wall MountBracket (L)

[18] Wall MountBracket (R)

[19] LCD Module Assembly

[20] Front Cabinet

(S-18)

(S-20)

(S-21)

(S-21)

(S-21)

(S-22)

Fig. D4

4-6 FL10.5DC

TV Cable Wiring Diagram

CN3901

Power Supply CBA

Jack CBA

WH2151

WH2154WH2152 CN2151WH2153

Digital Main CBA Unit

Junction-BCBA

Junction-ACBA

Function CBA

IR Sensor CBA

To LCD Module Assembly

To AC Inlet

To Speaker

CN3701 CN3702

CN1914CN1802

CN1801

CN1601

WH2101CN2101

CN2103CN2102WH2102

CN2106

CN2104CN2801CN2802


Fig. D5

4-7 FL10.5(A01PE_PFUH)DC

CABINET DISASSEMBLY INSTRUCTIONS[40MF430B/F7 (Serial No. : DS2A),

LC407SS1 (Serial No. : DS3A)]

1. Disassembly FlowchartThis flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.

2. Disassembly Method

Step/Loc. No.

Part

Removal

Fig. No.


Desolder

Note

[1] Stand Assembly D1 4(S-1), 2(S-2) ---

[2] Rear Cabinet D1 20(S-3), 2(S-4),

5(S-5), (S-6) ---

[3] Speaker Holder

D2D5

4(S-7), *CN2801, *CN2802 ---

[4] Speaker D2 --------------- ---

[1] StandAssembly

[2] Rear Cabinet

[7] Power SupplyCBA

[4] Speaker

[3] SpeakerHolder

[13] AC InletHolder

[14] StandBracket

[10] Jack Holder (D)

[8] Jack Holder(A)

[15] PCB Holder(D), (U)

[16] Wall Mount Bracket (L), (R)

[11] Digital MainCBA Unit

[9] Jack CBA

[12] Jack PCBHolder

[17] LCD ModuleAssembly

[18] FrontCabinet

[5] IR SensorCBA

[6] FunctionCBA

[5] IR Sensor CBA

D2D5

(S-8), *CN2104, *WH2152 ---

[6] Function CBA

D2D5 --------------- ---

[7] Power Supply CBA

D3D5

9(S-9), *CN1601, *CN1801, *CN1802, *CN1914

---

[8] Jack Holder(A) D3 (S-10) ---

[9] Jack CBA D3D5

5(S-11), *CN2102, *CN2103 ---

[10] Jack Holder(D) D3 (S-12) ---


D3D5

6(S-13), 4(S-14), *CN3901, Shield Box(Z)

---

[12] Jack PCB Holder D4 2(S-15), (S-16) ---

[13] AC Inlet Holder D4 2(S-17) ---

[14] Stand Bracket D4 4(S-18), 4(S-19) ---

[15] PCB Holder(D), (U) D4 6(S-20) ---

[16]Wall Mount Bracket(L), (R)

D4 4(S-21) ---

[17]LCD Module Assembly

D4 2(S-22) ---

[18] Front Cabinet D4 --------------- ---

↓(1)

↓(2)

↓(3)

↓(4)

↓(5)

Step/Loc. No.

Part

Removal

Fig. No.


Desolder

Note


Note:(1) Order of steps in procedure. When reassembling,

follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures.

(2) Parts to be removed or installed.(3) Fig. No. showing procedure of part location

(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connector* = Unhook, Unlock, Release, Unplug, or Desoldere.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)

(5) Refer to the following "Reference Notes in the Table."

[2] Rear Cabinet

[1] Stand Assembly

(S-1)(S-2)

(S-1)

(S-3)

(S-3)

(S-3)

(S-6)

(S-4)

(S-5)

(S-3)

(S-3)

(S-2)

(S-3)

Fig. D1


(S-7)

(S-8)

(S-7)

[5] IR Sensor CBA

[6] Function CBA

[3] Speaker Holder

[3] Speaker Holder

[4] Speaker

[4] Speaker

Fig. D2


(S-10)

(S-11)

(S-12)

[10] Jack Holder(D)

[8] JackHolder(A)[7] Power Supply CBA


[9] Jack CBA

Shield Box (Z)

(S-9)

(S-9)

(S-13)

(S-13)(S-14)

Fig. D3


(S-17)

(S-18)

(S-20)

(S-20)

(S-19)

(S-21)

(S-22)

(S-15)

(S-16)

[13] AC InletHolder

[15] PCB Holder(U)

[15] PCB Holder(D)

[12] Jack PCB Holder

[14] Stand Bracket[16] Wall MountBracket (L)

[16] Wall MountBracket (R)

[17] LCD Module Assembly

[18] Front Cabinet

(S-18)

(S-20)

(S-21)

(S-21)

(S-21)

(S-22)

Fig. D4


TV Cable Wiring Diagram

CN3901

Power Supply CBA

Jack CBA

WH2151

WH2154WH2152


Function CBA

IR Sensor CBA


To AC Inlet

To Speaker

CN3701 CN3702

CN1914CN1802

CN1801

CN1601

CN2103CN2102WH2102

CN2106

CN2104CN2801CN2802


Fig. D5

5-1 FL10.5EA

ELECTRICAL ADJUSTMENT INSTRUCTIONS

General Note: “CBA” is abbreviation for “Circuit Board Assembly.”Note: Electrical adjustments are required after

replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.

Test Equipment Required1. NTSC Pattern Generator (Color Bar W/White

Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst)

2. Remote control unit

3. Color Analyzer

How to set up the service mode:

Service mode:1. Turn the power on.

2. Press [MENU] button to display Setup menu.

3. Select “Features”.

4. Select “Current Software Info”.

5. Press [0], [4], [2], [5], [7], [4] and [Info] buttons on the remote control unit in this order. The following screen appears.

1. Purity Check ModeThis mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.

1. Enter the Service mode.

2. Each time pressing [7] button on the remote control unit, the display changes as follows.

3. To cancel or to exit from the Purity Check Mode, press [PREV CH] button.

Code : Pic code : MIPS :

Press "POWER" key to exit.

*******-***-*-*****-**** **-*******-*****-**Push 0key

Tuner : Safety :

****-*****-****safety_Non

"*" differs depending on the models.

[7] button

Note:When entering this mode, the default setting is White mode.

Purity Check Mode

[7] button

Red mode

Green mode

Blue mode

Black mode

[7] button

White mode

[7] button

[7] button

White 20% mode[7] button

5-2 FL10.5EA

The White Balance Adjustment should be performed when replacing the LCD Panel or Digital Main CBA.

2. White Balance AdjustmentPurpose: To mix red, green and blue beams correctly for pure white.

Symptom of Misadjustment: White becomes bluish or reddish.

1. Operate the unit for more than 20 minutes.

2. Input the White Raster(70%=70IRE, 40%=40IRE).

3. Set the color analyzer to the CHROMA mode and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.

4. Enter the Service mode. Press [VOLUME DOWN] button on the remote control unit and select “C/D” mode.

5. [CUTOFF]Press [1] button to select “COR” for Red Cutoff adjustment. Press [3] button to select “COB” for Blue Cutoff adjustment.[DRIVE]Press [4] button to select “DR” for Red Drive adjustment. Press [6] button to select “DB” for Blue Drive adjustment.

6. In each color mode, press [CHANNEL UP/DOWN] buttons to adjust the values of color.

7. Adjust Cutoff and Drive so that the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ±0.005).

8. To cancel or to exit from the White Balance Adjustment, press [PREV CH] button.

Test Point Adj. Point Mode Input

Screen[VOLUME DOWN]button

[VIDEO1]C/D

White Raster (APL 70%)

or(APL 40%)

M. EQ. Spec.

Pattern Generator, Color analyzer

x= 0.272 ± 0.005y= 0.278 ± 0.005

Figure

Color Analyzer

L = 3 cm

Perpendicularity

INPUT: WHITE 70%, 40%

To avoid interference from ambinent light, this adjustment should be performed in a dark room.

40%=40IRE 70%=70IRE100IRE100IRE

0IRE 0IRE

INPUT SIGNAL

LowLight

HightLight

6-1 PL10.3INT

HOW TO INITIALIZE THE LCD TV

The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized.To put the program back at the factory-default, initialize the LCD TV using the following procedure.

1. Turn the power on.

2. Enter the service mode.

- To cancel the service mode, press [POWER] button on the remote control unit.

3. Press [INFO] button on the remote control unit to initialize the LCD television.

4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed.

7-1 FL10.5FW

FIRMWARE RENEWAL MODE

Equipment Requireda. USB storage deviceb. Remote Control Unit

Firmware Update ProcedureNote: There are two states (the User Upgrade and

the Factory Upgrade) in firmware update.

The identification of User Upgrade and Factory Upgrade are done by the filename.

1. Turn the power off and unplug the AC Cord.

2. Insert the USB storage device to the USB port as shown below.The USB port “SERVICE TERMINAL” will be blocked by a cross shaped piece of plastic. Cutoff both end of the plastic connected to the PCB Holder as illustrated below.

3. Plug the AC cord in the wall outlet and turn the power on.

4. The update will start and the following will appear on the screen.

Note: If the above screen isn’t displayed, repeat from step 1.

The appearance shown in *1 is described as follows.

5. When the firmware update is completed, the following will appear on the screen.

Remove the USB storage device from the USB port. Turn the power off and turn the power on again.

Note:

When the Factory Upgrade is used, after restarting TV, shift to initial screen menu in service mode. "INITIALIZED" will appear on the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed.

User Upgrade Upgrade the firmware only. The setting values are not initialized.

Factory upgrade Upgrade the firmware and initialize the setting values.

USB port

Cut

USB storage device

SERVICETERMINAL

Rear Cabinet

Appearance State

Downloading... Downloading the firmware from the USB storage device.

Writing... Writing the downloaded firmware in flash memory.

Checking... Checking the new firmware.

Software upgrade in progress. Please wait.Do not remove the USB storage device or turn the TV off while upgrade is in progress.

Software Upgrade

Downloading...

Current Version:New Version:

*******-***-*-***-***********-***-*-***-****

0%*1

"*" differs depending on the models.

Software Upgrade

The software upgrade is completed.Remove USB storage device, turn TV off then on again.

8-1 FL10.5TR

TROUBLESHOOTING

[ Power Supply Section ]

The power cannot be turned on.

The fuse blows out.

FLOW CHART NO.1

FLOW CHART NO.2

Is normal state restored when once unpluggedpower cord is plugged again several seconds?

Check if there is any leak or short-circuiting on theprimary circuit component, and service it if defective.(D1201, D1202, D1203, D1204, IC1201, T1201)

Yes

No

Yes

Is the fuse (F1601) normal? See FLOW CHART No.2 <The fuse blows out.>

No

Check if there is any leak or short-circuiting on theprimary circuit component, and service it if defective.(D1607, D1608, D1609, D1610, IC1401, IC1702, Q1601, Q1602, Q1701, Q1702, T1701)

No

Yes

Is the AL+4.3V line voltage normal?No

Is the PANEL+24V line voltage normal?

Yes

Check if there is any leak or short-circuiting on theprimary circuit component, and service it if defective.(D1607, D1608, D1609, D1610, IC1401, Q601, Q602, Q1601, Q1602, T601)

NoIs the LCD+12V line voltage normal?

Yes

Check each rectifying circuit of the secondarycircuit and service it if defective.

Check the presence that the primary componentis leaking or shorted and service it if defective.

Check the presence that the rectifying diode or circuit is shorted in each rectifying circuit of secondary side, and service it if defective.

After servicing, replace the fuse (F1601).

When the output voltage fluctuates.FLOW CHART NO.3

Does the photocoupler circuit on the secondary side operate normally?

No

Yes

Check D668, IC601 and their periphery circuit, and service it if defective.

When buzz sound can be heard in the vicinity of power circuit.FLOW CHART NO.4

Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side,and service it if defective. (D651, D656, D662, D665, D670, D672, D673, D1101, D1102, D1721, Q652, Q653)

Check D607, D609, D615, IC601, IC1401, Q1601, Q1602, L1603, L1604 and their periphery, circuit and service it if defective.

8-2 FL10.5TR

Check if there is any leak or short-circuit on the loaded circuit, and service it if defective.

AL+4.3V is not output.FLOW CHART NO.5

Is approximately +4.3V voltage supplied to thecathode of D1102?

No

Yes

Check C1102, D1102 and their periphery circuit, and service it if defective.


PANEL+24V is not output.

Is approximately +24V voltage supplied to thecathode of D1721?

No

Yes

Check C1725, C1727, D1721 and their periphery circuit, and service it if defective.


P-ON+7.5V is not output.


No

Yes


Check D2638, R2655 and their periphery circuit, and service it if defective.

TUNER+35V is not output.

FLOW CHART NO.9


No

Yes

Check C652, D651, D652 and their periphery circuit, and service it if defective.

AL+3.3V is not output.FLOW CHART NO.6

Is approximately +4.3V voltage supplied to Pin(1) of IC2631?

No

Yes

Replace IC2631.


FLOW CHART NO.7

FLOW CHART NO.8

8-3 FL10.5TR

FLOW CHART NO.10

P-ON+5V is not output.

FLOW CHART NO.11

Is approximately +8V voltage supplied to thecollector of Q652?


Yes

No

Replace Q652.


FLOW CHART NO.12

Is approximately +5V voltage supplied to thecollector of Q653?

Is approximately +4V voltage supplied to the base of Q653?

NoYes

Yes

Check D666 and their periphery circuit, and service it if defective.


Is approximately +6V voltage supplied to the base of Q652?

NoYes

Check D664 and their periphery circuit, and service it if defective.

No

Replace Q653.


LCD+12V is not output.


No

Yes


FLOW CHART NO.13



Is approximately +3.5V voltage supplied to thecathode of D670?

No

Yes


FLOW CHART NO.14


AMP+24V is not output.


No

Yes


8-4 FL10.5TR

[ Video Signal Section ]

No

Is the "L" pulse sent out Pin(1) terminal of remote control receiver (RS2151) when the infrared remote control is activated?

Check the line between Pin(1) terminal of remote control receiver(RS2151) and Pin(23) of CN2103, and service it if defective.

Yes

Is the "L" pulse supplied to Pin(23) of CN2103?

Yes

Is 3.3V voltage supplied to Pin(2) terminal of theremote control receiver (RS2151)?

No

FLOW CHART NO.2

Operation is possible from the unit.

Check AL+3.3V line and service it if defective.

NoReplace the remote control receiver(RS2151) or the remote control unit.

Yes

Replace Digital Main CBA Unit.

When pressing each switches (SW2151~SW2156) do the voltage of Pin(25) of CN2103 increase?

Yes

The key operation is not functioning.FLOW CHART NO.1

Are the contact point and installation state of the key switches (SW2151~SW2156) normal?

Re-install the switches (SW2151~SW2156) correctly or replace the poor switch.

Check the switches (SW2151~SW2156) and their periphery, and service it if defective.

Yes


No

No

No operation is possible from the remote control unit.

8-5 FL10.5TR

Replace Digital Main CBA Unit or LCD Module Assembly.

Is 5V voltage supplied to the Pin(2, 29, 33, 39, 44) of IC2701?Is 8V voltage supplied to the Pin(12) of IC2701?

Replace IC2701. Check P-ON+5V, P-ON+8V line and service it if defective.

Yes No

Yes

Yes

FLOW CHART NO.3Picture does not appear normally. (EXT. input)

FLOW CHART NO.4Picture does not appear normally. (Tuner input)

Are the video signals inputted to each pin of IC2701? Check the line between video input terminal andeach pin of IC2701.

Are the video signals outputted to each pin of IC2701?

Yes

No

No

No

IC2701 VIDEO-IN 13PINIC2701 Y-IN 11PIN

IC2701 CVBS/Y/S-Y38PINIC2701 Pb36PINIC2701 Pr/S-C34PIN

IC2701 C-IN 19PINIC2701 VIDEO-IN 27PINIC2701 Y-IN 2 5PINIC2701 C-IN 2 11PIN IC2701 COMPONENT-Y-IN41PIN IC2701 COMPONENT-Pb-IN45PIN IC2701 COMPONENT-Pr-IN

VIDEO-IN 1Y-IN 1C-IN 1VIDEO-IN 2Y-IN 2 C-IN 2 COMPONENT-Y-INCOMPONENT-Pb-INCOMPONENT-Pr-IN50PIN

IC2701 3PINIC2701 1PINIC2701 9PINIC2701 7PINIC2701 5PINIC2701 11PIN IC2701 41PIN IC2701 45PIN IC2701 50PIN

→ JK2703→ JK2702→ JK2702→ JK2707→ JK2706→ JK2706→ JK2714→ JK2715→ JK2716

Check the line between Pin(3, 4) of CN2102 and TU2301, and service it if defective.

Are the DIF signal inputted to Pin(3, 4) of CN2102?

Replace Digital Main CBA Unit or LCD ModuleAssembly.

8-6 FL10.5TR

[ Audio Signal Section ]

Check SP2801,SP2802 and their periphery circuit,and service it if defective.

Are the audio(L/R) signals inputted to Pin(19, 32)of IC2801?

Yes

Yes

No

Are the audio(L/R) signals outputted to CN2801 and CN2802?

Check IC2801 and their periphery circuit, and service it if defective.

No

Yes

Yes

Yes

Yes

Check the line between Pin(26, 28) of CN2103 and Pin(19, 32) of IC2801, and service it if defective.


Is 5V voltage supplied to the Pin(2, 29, 33, 39, 44) of IC2701?Is 8V voltage supplied to the Pin(12) of IC2701?

Replace IC2701. Check P-ON+5V, P-ON+8V line and service it if defective.

Yes NoYes (Output to speakers)

Yes (Output to audiooutput terminal)

FLOW CHART NO.1Audio is not outputted. (EXT. input)

Are the audio(L/R) signals inputted to each pin of IC2701?

Check the line between audio input terminal andeach pin of IC2701.

Are the audio(L/R) signals outputted to Pin(27, 28) of IC2701?

Are the audio(L/R) signals outputted to Pin(26, 28) of CN2103?

Yes

No

No

No

No

Replace Digital Main CBA Unit.Are the audio(L/R) signals outputted to Pin(4, 6) of CN2103?

No

IC2701 AUDIO(L/R)-IN 1AUDIO(L/R)-IN 2COMPONENT AUDIO(L/R)-INHDMI AUDIO(L/R)-IN

AUDIO(L/R)-IN 1AUDIO(L/R)-IN 2COMPONENT AUDIO(L/R)-INHDMI AUDIO(L/R)-IN

14,15PINIC2701 16,17PINIC2701 18,19PINIC2701 24,25PIN

14,15PIN16,17PIN18,19PIN24,25PIN

IC2701IC2701IC2701IC2701

→ JK2704, JK2705→ JK2708, JK2709→ JK2710, JK2711→ JK2720, JK2721



NoAre the audio(L/R) signals outputted to Pin(1, 7)of IC2802?

Check the line between Pin(1, 7) of IC2802 and audiooutput terminal(JK2801, JK2802) and service it if defective.

Replace IC2802

8-7 FL10.5TR

Yes (Output to speakers)

Yes (Output to audiooutput terminal)

FLOW CHART NO.2Audio is not outputted. (Tuner input)

No

No

No

No

No

Are the DIF signal inputted to Pin(3, 4) of CN2102?

Yes

Yes

No

No

Yes

Yes

Yes

Yes

Check SP2801,SP2802 and their periphery circuit,and service it if defective.


Are the audio(L/R) signals outputted to CN2801 and CN2802?

Check IC2801 and their periphery circuit, and service it if defective.






Are the audio(L/R) signals outputted to Pin(1, 7)of IC2802?

Check the line between Pin(1, 7) of IC2802 and audiooutput terminal(JK2801, JK2802) and service it if defective.

Replace IC2802

Check the line between Pin(3, 4) of CN2102 and TU2301, and service it if defective.

9-1

AC18

KE

Y S

WIT

CH

IC33

01(M

AIN

MIC

RO

CO

NT

RO

LLE

R)

DIG

ITA

L M

AIN

CB

A U

NIT

IR S

EN

SO

R C

BA

FU

NC

TIO

N C

BA

PO

WE

R S

UP

PLY

CB

AJA

CK

CB

A

WH

2154R

EM

OT

ES

EN

SO

R

RS

2151

AL+

3.3V

STA

ND

BY

D21

51

PO

WE

RD

2153

WH

2153

WH

2151

RE

MO

TE

55

LED

-R2

2

CN

2103

CN

3702

CN

3702

CN

2103

CLK

OU

T-25

MC

LKIN

-25M

X31

0225

MH

zO

SC

N1

N2

SC

L

Q24

01

SD

A8 7

TU

2301

(TU

NE

R U

NIT

)

SC

LS

DA

4 5

TU

2301

(TU

NE

R U

NIT

)

PR

OT

EC

T3

AE

5

PR

OT

EC

T1

AD

5

KE

Y-IN

1LI

GH

TAC

5

BA

CK

LIG

HT-

SW

AB16

P-O

N-H

2AB

13

RE

MO

TE

R22

LED

-RF

3

LIG

HT

-S

EN

SO

R

D21

56

*1

JUN

CT

ION

-A

CB

A

CN

2151

KE

Y-IN

11

1 WH

2152

CN

1801

KE

Y-IN

11

1

CN

2106

CN

2104

LED

13

3

AB23

W26

BA

CK

LIG

HT-

AD

JR

ES

ET

IC31

01 (

ME

MO

RY

)

SC

K SI

SO

AB25

AB24

AC25

AC24

6 5 2 1E

11

F1

3AC

19

SC

L

SD

A

RE

SE

T

IC31

03

CN

2102

CN

3701

CS

WP

SC

KA

L+3.

3VS

INS

OU

TC

SW

P

TO P

OW

ER

SU

PP

LY 1

B

LOC

K D

IAG

RA

M

P-O

N-H

2P

-ON

-H1

PR

OT

EC

T3

PO

WE

R-R

ES

ET

BA

CK

LIG

HT-

SW

BA

CK

LIG

HT-

AD

J

TO P

OW

ER

SU

PP

LY 2

B

LOC

K D

IAG

RA

M

1818

SC

L

1717

SD

A

99

PR

OT

EC

T1

88

PR

OT

EC

T3

2121

BAC

KLI

GH

T-S

W22

22B

ACK

LIG

HT-

AD

J7

7R

ES

ET

KE

Y-IN

125

25LI

GH

T-S

EN

SO

R1

1

LED

-R5

5

RE

MO

TE

2323

LED

1LE

D1

2424

P-O

N-H

210

10P

-ON

-H2

R23

P-O

N-H

16

6

122

PR

OT

EC

T3

104

BAC

KLI

GH

T-S

W

95

BAC

KLI

GH

T-A

DJ

86

PO

WE

R-R

ES

ET

P-O

N-H

16

8P

-ON

-H2

77

RE

MO

TE

55

LED

-R2

2K

EY-

IN1

11

LED

13

3LI

GH

T-S

EN

SO

R7

7LI

GH

T-S

EN

SO

R7

7

TO A

UD

IOB

LOC

K

DIA

GR

AM

AU

DIO

-MU

TE

AU

DIO

-MU

TE

AB9

AE6

113

PR

OT

EC

T1

PR

OT

EC

T1

Eit

her

TU

2301

is u

sed

for

Jack

CB

A.

* *

BLOCK DIAGRAMSSystem Control Block Diagram

FL10.5BLS

*140

MF

430B

/F7,

LC

407S

S1

(Ser

ial

No

. :

DS

2A)

LC

40

7E

M1

[40MF430B/F7(Serial No.:DS1A), LC407SS1(Serial No.:DS1A,DS2A), LC407EM1]

9-2

AC18

KE

Y S

WIT

CH

IC33

01(M

AIN

MIC

RO

CO

NT

RO

LLE

R)

DIG

ITA

L M

AIN

CB

A U

NIT

IR S

EN

SO

R C

BA

FU

NC

TIO

N C

BA

PO

WE

R S

UP

PLY

CB

AJA

CK

CB

A

WH

2154R

EM

OT

ES

EN

SO

R

RS

2151

AL+

3.3V

STA

ND

BY

D21

51

PO

WE

RD

2153

WH

2151

CN

2103

CN

3702

CN

3702

CN

2103

CLK

OU

T-25

MC

LKIN

-25M

X31

0225

MH

zO

SC

N1

N2

SC

L

Q24

01

SD

A8 7

TU

2301

(TU

NE

R U

NIT

)

PR

OT

EC

T3

AE

5

PR

OT

EC

T1

AD

5

KE

Y-IN

1LI

GH

TAC

5

BA

CK

LIG

HT-

SW

AB16

P-O

N-H

2AB

13

RE

MO

TE

R22

LED

-RF

3

LIG

HT

-S

EN

SO

R

D21

56

WH

2152

CN

1801

KE

Y-IN

11

1

CN

2106

CN

2104

AB23

W26

BA

CK

LIG

HT-

AD

JR

ES

ET

IC31

01 (

ME

MO

RY

)

SC

K SI

SO

AB25

AB24

AC25

AC24

6 5 2 1E

11

F1

3AC

19

SC

L

SD

A

RE

SE

T

IC31

03

CN

2102

CN

3701

CS

WP

SC

KA

L+3.

3VS

INS

OU

TC

SW

P

TO P

OW

ER

SU

PP

LY 1

B

LOC

K D

IAG

RA

M

P-O

N-H

2P

-ON

-H1

PR

OT

EC

T3

PO

WE

R-R

ES

ET

BA

CK

LIG

HT-

SW

BA

CK

LIG

HT-

AD

J

TO P

OW

ER

SU

PP

LY 2

B

LOC

K D

IAG

RA

M

1818

SC

L

1717

SD

A

99

PR

OT

EC

T1

88

PR

OT

EC

T3

2121

BAC

KLI

GH

T-S

W22

22B

ACK

LIG

HT-

AD

J7

7R

ES

ET

KE

Y-IN

125

25LI

GH

T-S

EN

SO

R1

1

LED

-R5

5

RE

MO

TE

2323

LED

1LE

D1

2424

P-O

N-H

210

10P

-ON

-H2

R23

P-O

N-H

16

6

122

PR

OT

EC

T3

104

BAC

KLI

GH

T-S

W

95

BAC

KLI

GH

T-A

DJ

86

PO

WE

R-R

ES

ET

P-O

N-H

16

8P

-ON

-H2

77

RE

MO

TE

55

LED

-R2

2K

EY-

IN1

11

LED

13

3LI

GH

T-S

EN

SO

R7

7

TO A

UD

IOB

LOC

K

DIA

GR

AM

AU

DIO

-MU

TE

AU

DIO

-MU

TE

AB9

AE6

113

PR

OT

EC

T1

PR

OT

EC

T1

SC

LS

DA

4 5

TU

2301

(TU

NE

R U

NIT

)

Eit

her

TU

2301

is u

sed

for

Jack

CB

A.

* *

System Control Block Diagram

FL10.5BLS_2

[40MF430B/F7(Serial No.:DS2A), LC407SS1(Serial No.:DS3A)]

9-3 FL10.5BLV

Video Block Diagram

IC27

01

(IN

PU

T S

ELE

CT

)D

IGIT

AL

MA

IN C

BA

UN

IT

TO D

IGIT

AL

SIG

NA

L P

RO

CE

SS

BLO

CK

DIA

GR

AM

JK27

03V

IDE

O-I

N1

CO

MP

ON

EN

T-Y

-IN

CO

MP

ON

EN

T-P

b-IN

CO

MP

ON

EN

T-P

r-IN

JK27

14

JK27

15

JK27

16

3

38 36 34

7 1 5 9 11 41 45 50 51

CV

BS

/Y/S

-Y-I

N8

8P

b-IN

1010

Pr/

S-C

-IN

1212

VID

EO

INP

UT

S

ELE

CTO

R

WF

1W

F2

WF

3C

Y

S-V

IDE

O-S

W1

49S

-VID

EO

-SW

2

JK27

06S

-VID

EO

-IN

2

CY

JK27

07V

IDE

O-I

N2

JK27

02S

-VID

EO

-IN

1

JAC

K C

BA

CV

BS

/Y/S

-Y-I

NP

b-IN

Pr/

S-C

-IN

TU

2301

DIF

-OU

T1

11D

IF-O

UT

212

(TU

NE

R U

NIT

)

IF-A

GC

10

CN

2102

CN

3701

DIF

-OU

T1

33

IF-A

GC

11

DIF

-OU

T2

44

TU

2301

DIF

-OU

T1

10D

IF-O

UT

211

(TU

NE

R U

NIT

)

IF-A

GC

9

TO D

IGIT

AL

SIG

NA

L P

RO

CE

SS

BLO

CK

DIA

GR

AM

DIF

-OU

T1

DIF

-OU

T2

IF-A

GC

CN

2103

CN

3702

VID

EO

SIG

NA

LA

UD

IO S

IGN

AL

Eit

her

TU

2301

is u

sed

for

Jack

CB

A.

**

*

9-4

IC27

01(I

NP

UT

SE

LEC

T)

AU

DIO

(L)-

IN1

AU

DIO

(R)-

IN1

JK27

04

JK27

05

CO

MP

ON

EN

TA

UD

IO(L

)-IN

CO

MP

ON

EN

TA

UD

IO(R

)-IN

HD

MI-

AU

DIO

(L)-

IN

HD

MI-

AU

DIO

(R)-

IN

JK27

20

JK27

21

JK27

10

JK27

11

14 16

28 27

18 15 17 19

AU

DIO

INP

UT

S

ELE

CTO

R

AU

DIO

(L)-

OU

T

AU

DIO

(R)-

OU

T

JK28

01

JK28

02

24 25

AU

DIO

(L)-

IN2

AU

DIO

(R)-

IN2

JK27

08

JK27

09

CN

3702

CN

2103

AU

DIO

(L)

2020

AU

DIO

(R)

2222

JAC

K C

BA

AU

DIO

(L)

AU

DIO

(R)

DIG

ITA

L M

AIN

CB

A U

NIT

WF

4

34

IC28

01 (

AU

DIO

AM

P)

IC28

02

(OP

AM

P)

32

7 1

5 3

19

39,4

0

11,1

2

CO

NT

RO

L LO

GIC

CN

2801

CL2

801

SP

2801

SP

EA

KE

RL-

CH

CN

2802

SP

(R)-

1

CL2

802

SP

2802

SP

EA

KE

RR

-CH

PW

M

GE

NE

.

PW

MG

EN

E.

IC35

03(A

UD

IO D

/A C

ON

VE

RT

ER

)IC

3501

(AU

DIO

DS

P)

D/A

CO

NV

ER

TE

RD

SP

(L-C

H)

(R-C

H)

15 145678

37 34333635

39 34402

IC35

02(A

UD

IO D

/A C

ON

VE

RT

ER

)

D/A

CO

NV

ER

TE

R

(L-C

H)

(R-C

H)

15 145678

CN

2103

CN

3702

CN

2103

CN

3702

AU

DIO

-MU

TE

1414

JK27

01D

IGIT

AL

AU

DIO

-OU

T(C

OA

XIA

L)

Q27

01B

UF

FE

R

Q28

04,Q

2805

DR

IVE

Q28

01M

UT

E

SP

DIF

22

AU

DIO

(L)-

OU

T4

4A

UD

IO(R

)-O

UT

66

AM

P(L

)-O

UT

2626

AM

P(R

)-O

UT

2828

SP

(R)+

2

SP

(L)-

1S

P(L

)+2

AC

LKA

DAT

A0

BC

LKLR

CLK

AD

ATA

1

TO

DIG

ITA

L S

IGN

AL

P

RO

CE

SS

BLO

CK

DIA

GR

AM

TO

DIG

ITA

L S

IGN

AL

PR

OC

ES

SB

LOC

K D

IAG

RA

M

AU

DIO

-MU

TE

TO

SY

ST

EM

CO

NT

RO

L B

LOC

K D

IAG

RA

M

Q28

03

Q28

02M

UT

E

SP

DIF

AU

DIO

SIG

NA

L

Audio Block Diagram

FL10.5BLA

9-5

Digital Signal Process Block Diagram

FL10.5BLD

LVD

S-D

4O(+

)35

LVD

S-D

4O(-

)36

DIG

ITA

L M

AIN

CB

A U

NIT

IC33

01 (

DIG

ITA

L S

IGN

AL

PR

OC

ES

S)

LCD

MO

DU

LEA

SS

EM

BLY

CN

3901

LVD

S-D

1E(+

)21

LVD

S-D

1E(-

)22

LVD

S-D

0E(+

)23

LVD

S-D

0E(-

)24

LVD

S-D

2E(+

)19

LVD

S-D

2E(-

)20

LVD

S-D

3E(+

)13

LVD

S-D

3E(-

)14

LVD

S-D

0O(+

)47

LVD

S-D

0O(-

)48

LVD

S-D

1O(+

)45

LVD

S-D

1O(-

)46

LVD

S-D

2O(+

)43

LVD

S-D

2O(-

)44

LVD

S-D

3O(+

)37

LVD

S-D

3O(-

)38

LVD

S-E

CLK

(+)

16LV

DS

-EC

LK(-

)17

AD23

AD24

AE23

AF23

AF22

AE22

AD21

AD22

AF24

AE24

AF18

AE18

AD17

AD18

AE17

AF17

AF16

AE16

AD15

AD16

LVD

ST

X

LVD

S-D

4E(+

)11

LVD

S-D

4E(-

)12

AE21

AF21

LVD

S-O

CLK

(+)

40LV

DS

-OC

LK(-

)41

AE19

AF19

DIG

ITA

LS

IGN

AL

PR

OC

ES

S

A/D

CO

NV

ER

TER

SW

V1

V2

U2

U1

U3

V3

Pr/

S-C

-IN

Pb-

INC

VB

S/Y

/S-Y

-IN

AA3

IF-A

GC

HD

MI2

-SC

LH

DM

I2-S

DA

HD

MI-

IN1

JK38

03

DAT

A0(

+)

DAT

A0(

-)D

ATA

1(+

)D

ATA

1(-)

DAT

A2(

+)

DAT

A2(

-)

HD

MI-

CLO

CK

HD

MI-

DAT

A

7 9 4 6 1 3 10 12 15 16

CLO

CK

(+)

CLO

CK

(-)

DE

MO

DU

LATO

R/M

PE

G D

EC

OD

ER

AF2

AF7

AU

DIO

I/F

TO A

UD

IOB

LOC

K D

IAG

RA

MA

CLK

AD

ATA

1

BC

LKLR

CLK

AD

ATA

0S

PD

IF

AD14

AD9

AD12

AD10

AD11

AC10

HD

MI

I/F

D1

D2

C1

C2

B1

B2

A1

A2

DIF

-OU

T1

DIF

-OU

T2

IF-A

GC

TO V

IDE

OB

LOC

K D

IAG

RA

M

AE2

M2

AU

DIO

(R)

M1

AU

DIO

(L)

VID

EO

SIG

NA

LA

UD

IO S

IGN

AL

HD

MI-

IN2

JK38

01

DAT

A0(

+)

DAT

A0(

-)D

ATA

1(+

)D

ATA

1(-)

DAT

A2(

+)

DAT

A2(

-)

HD

MI-

CLO

CK

HD

MI-

DAT

A

7 9 4 6 1 3 10 12 15 16

CLO

CK

(+)

CLO

CK

(-)

HD

MI-

IN3

JK38

02

DAT

A0(

+)

DAT

A0(

-)D

ATA

1(+

)D

ATA

1(-)

DAT

A2(

+)

DAT

A2(

-)

HD

MI-

CLO

CK

HD

MI-

DAT

A

7 9 4 6 1 3 10 12 15 16

CLO

CK

(+)

CLO

CK

(-)

B8

A8

C8

C9

A9

B9

B10

A10 B4

A4

C4

C5

A5

B5

B6

A6

B3

A3

HD

MI0

-SC

LH

DM

I0-S

DA

B11

A11

HD

MI1

-SC

LH

DM

I1-S

DA

B7

A7

S0-D

Q (0

-15)

S0-A

(0-1

2)

(DD

R2

SD

RA

M)

IC32

01

DD

R2

SD

RA

M(

512M

bit

)

S1-D

Q (0

-15)

S1-A

(0-1

2)

(DD

R2

SD

RA

M)

IC32

02

DD

R2

SD

RA

M(

512M

bit

)

AU

DIO

DE

CO

DE

R

VID

EO

DE

CO

DE

R

9-6 FL10.5BLP1

Power Supply 1 Block DiagramC

AU

TIO

N !

Fix

ed v

olta

ge (

or A

uto

volta

ge s

elec

tabl

e) p

ower

sup

ply

circ

uit i

s us

ed in

this

uni

t.If

Mai

n F

use

(F16

01)

is b

low

n , c

heck

to s

ee th

at a

ll co

mpo

nent

s in

the

pow

er s

uppl

yci

rcui

t are

not

def

ectiv

e be

fore

you

con

nect

the

AC

plu

g to

the

AC

pow

er s

uppl

y.O

ther

wis

e it

may

cau

se s

ome

com

pone

nts

in th

e po

wer

sup

ply

circ

uit t

o fa

il.

For

con

tinue

d pr

otec

tion

agai

nst r

isk

of fi

re,

repl

ace

only

with

sam

e ty

pe 8

A, 2

50V

fuse

.C

AU

TIO

N !

:

AT

TE

NT

ION

: U

tilis

er u

n fu

sibl

e de

rec

hang

e de

mêm

e ty

pe d

e 8

A, 2

50V

.8A

250

V

NO

TE

:T

he v

olta

ge fo

r pa

rts

in h

ot c

ircui

t is

mea

sure

d us

ing

hot G

ND

as

a co

mm

on te

rmin

al.

LCD

MO

DU

LEA

SS

EM

BLY

HO

TC

OL

D

HO

T C

IRC

UIT

. BE

CA

RE

FU

L.

CN

1601

1 2

AC

601

AC

CO

RD

AC

IN

LET

LIN

EF

ILT

ER

L160

1

LIN

EF

ILT

ER

L160

2

T12

01

BR

IDG

ER

EC

TIF

IER

D12

01-D

1204

BR

IDG

ER

EC

TIF

IER

D16

07-D

1610

L160

4

DR

AIN

VC

C

VD

D

FB

TO S

YS

TE

M C

ON

TR

OL

BLO

CK

DIA

GR

AM

PO

WE

R S

UP

PLY

CB

A

AL+

4.3V

+34

5VH

OT

+20

V

F16

01

8A/2

50V

5 7 9 10

1 2 4

6

3

2 5

11 8

T17

01

8 7 5 34 2 1

109 11 12 13 14 15 16

IC12

02

14 3

2

IC12

01(S

WIT

CH

ING

)

Q16

02S

WIT

CH

ING

Q16

01

VC

CS

WIT

CH

ING

(FE

ED

BA

CK

)

RL1

201

Q12

02

Q12

01

Q17

01S

WIT

CH

ING

Q17

02S

WIT

CH

ING

IC17

05(I

SO

LAT

OR

)

IC17

04(F

EE

D B

AC

K)

IC14

01(S

WIT

CH

ING

CO

NT

RO

L)

IC17

02H

IGH

-VO

LTA

GE

R

ES

ON

AN

T C

ON

TR

OL

SW

ITC

HIN

G

CO

NT

RO

L

7

11

116

12

14

L160

3

2 5

11 8

HIG

H-

VO

LTA

GE

RE

SO

NA

NT

CO

NT

RO

L

8

8 12 13 2 149 5 4

14 3

2 14 3

2

IC17

03(I

SO

LAT

OR

)

Q17

05

Q17

03

Q17

04

Q14

04

Q14

03

Q14

02

Q14

01

Q17

07

Q17

08

14 3

2

CN

1914

PAN

EL+

24V

1-5

P-O

N-H

2P

-ON

-H1

PR

OT

EC

T3

BA

CK

LIG

HT-

AD

JB

AC

KLI

GH

T-S

W

Q17

06

BAC

KLIG

HT-

ADJ

13

BAC

KLIG

HT-

ADJ

14

BAC

KLIG

HT-

SW12

5 1 24

PO

WE

R-R

ES

ET

TO S

YS

TE

M C

ON

TR

OL

BLO

CK

DIA

GR

AM

*1 *2 *140

MF

430B

/F7

(Ser

ial

No

. :

DS

1A),

LC

407S

S1

(Ser

ial

No

. :

DS

1A,

DS

2A)

LC

40

7E

M1

*240

MF

430B

/F7

(Ser

ial

No

. :

DS

2A),

LC

407S

S1

(Ser

ial

No

. :

DS

3A)

9-7 FL10.5BLP2

Power Supply 2 Block Diagram

TU

NE

R+

35V

AM

P+

24V

HO

TC

OL

DP

OW

ER

SU

PP

LY C

BA

HO

T C

IRC

UIT

. BE

CA

RE

FU

L.

Q60

2S

WIT

CH

ING

CO

NT

RO

L

14 3

2

IC60

1

T60

1

73 6

910 1611 14 15 12 13

1 52

Q60

1S

WIT

CH

ING

CN

1802

CN

2101

Q65

2S

W+

5V

TO S

YS

TE

M C

ON

TR

OL

BLO

CK

DIA

GR

AM

PR

OT

EC

T1

P-O

N+

3.3V

682,3

LCD

+12

VP

-ON

+3.

5V

P-O

N+

7.5V

P-O

N+

5VP

-ON

+3.

3V

JUN

CT

ION

-B

CB

AJA

CK

CB

A

10P

-ON

+3.

5V10

14A

MP

+24

V14

1T

UN

ER

+35

V1

P-O

N+

3.3V

612

P-O

N+

5V12

P-O

N+

7.5V

8LC

D+

12V

2,3

WH

2101

WH

2102

682,3

10P

-ON

+3.

5V10

14A

MP

+24

V14

1T

UN

ER

+35

V1

P-O

N+

3.3V

612

P-O

N+

5V12

P-O

N+

7.5V

8LC

D+

12V

2,3

Q65

3S

W+

3.3V

(FE

ED

BA

CK

)

+34

5V

HO

T+

20V

NO

TE

:T

he v

olta

ge fo

r pa

rts

in h

ot c

ircui

t is

mea

sure

d us

ing

hot G

ND

as

a co

mm

on te

rmin

al.


9-8 FL10.5BLP3

TU

NE

R+

35V

AM

P+

24V

HO

TC

OL

DP

OW

ER

SU

PP

LY C

BA

HO

T C

IRC

UIT

. BE

CA

RE

FU

L.

Q60

2S

WIT

CH

ING

CO

NT

RO

L

14 3

2

IC60

1

T60

1

73 6

910 1611 14 15 12 13

1 52

Q60

1S

WIT

CH

ING

CN

1802

Q65

2S

W+

5V

TO S

YS

TE

M C

ON

TR

OL

BLO

CK

DIA

GR

AM

PR

OT

EC

T1

P-O

N+

3.3V

LCD

+12

VP

-ON

+3.

5V

P-O

N+

7.5V

P-O

N+

5VP

-ON

+3.

3V

JAC

K C

BA

WH

2102

682,3

10P

-ON

+3.

5V10

14A

MP

+24

V14

1T

UN

ER

+35

V1

P-O

N+

3.3V

612

P-O

N+

5V12

P-O

N+

7.5V

8LC

D+

12V

2,3

Q65

3S

W+

3.3V

(FE

ED

BA

CK

)

+34

5V

HO

T+

20V

NO

TE

:T

he v

olta

ge fo

r pa

rts

in h

ot c

ircui

t is

mea

sure

d us

ing

hot G

ND

as

a co

mm

on te

rmin

al.

[40MF430B/F7(Serial No.:DS2A), LC407SS1(Serial No.:DS3A)]Power Supply 2 Block Diagram

10-1 FL10.5SC

SCHEMATIC DIAGRAMS / CBA AND TEST POINTS

Standard Notes

WARNING

Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.

Notes:1. Do not use the part number shown on these

drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.

2. All resistance values are indicated in ohms (K = 103, M = 106).

3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.

4. All capacitance values are indicated in µF (P = 10-6 µF).

5. All voltages are DC voltages unless otherwise specified.

6. This schematic diagrams are masterized version that should cover the entire FL10.5 chassis models.Thus some parts in detail illustrated on this schematic diagrams may vary depend on the model within the FL10.5 chassis.Please refer to the parts lists for each models.

7. The Circuit Board layout illustrated on this service manual is the latest version for this chassis at the moment of making this service manual. Depend on the mass production date of each model, the actual layout of each Board may differ slightly from this version.

10-2 FL10.5SC

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:

1. CAUTION:CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE.

ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.

2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1601) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

3. Note:1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the

parts list, and may be slightly different or amended since the drawings were prepared.

2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.

4. Voltage indications on the schematics are as shown below: Plug the TV power cord into a standard AC outlet.:

5. How to read converged lines

6. Test Point Information

2 315.0 5.0

Voltage Indicates that the voltage is not consistent here.

Power on mode(Unit: Volt)

3

2

1

A B C D

1-B1

1-D3

AREA D3

AREA B1

1-D3

Distinction AreaLine Number (1 to 3 digits)

Examples:1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".

: Indicates a test point with a jumper wire across a hole in the PCB.

: Used to indicate a test point with a component lead on foil side.

: Used to indicate a test point with no test pin.

: Used to indicate a test point with a test pin.

10-3 FL10.5SCP1

Power Supply 1 Schematic Diagram

NOTE:The voltage for parts in hot circuit is measured using hot GND as a common terminal.

For continued protection against risk of fire, replace only with same type 8A, 250V fuse.

CAUTION ! :

ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.8A 250V

CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1601) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.

10-4 FL10.5SCP2

Power Supply 2 Schematic DiagramNOTE:The voltage for parts in hot circuit is measured using hot GND as a common terminal.

10-5 FL10.5SCP3

Power Supply 3 Schematic DiagramNOTE:The voltage for parts in hot circuit is measured using hot GND as a common terminal.

10-6 FL10.5SCJ1

Jack 1 Schematic Diagram

10-7 FL10.5SCJ2

Jack 2 & Junction-B Schematic Diagram

10-8 FL10.5SCF

Function Schematic Diagram

10-9 FL10.5SCIR

IR Sensor & Junction-A Schematic Diagram

10-10 FL10.5SCD1

Digital Main 1 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.

1 NOTE:

10-11 FL10.5SCD2



1 NOTE:

10-12 FL10.5SCD3



1 NOTE:

10-13 FL10.5SCD4



1 NOTE:

10-14 FL10.5SCD5



1 NOTE:

10-15

6 1

CAUTION - RISK OF FIRE -REPLACE FUSE AS MARKED

TOOL NO.

1 2 3 4 5 6 7 8 910

C7A3 A3 G

BA01P0F0103 3

46W-ONLY

HOT-GNDJ1020

HOT-GNDJ1022

HOT-GNDJ1027

C1702

C1703

D1103

C170

4

D110

4

Q1701

Q1702

C170

6

R607

Q1703

R608

Q1704

R609

Q1705

Q1706

+12V

J1033

Q1707

Q1708

J103

5

PWMC

TRL

J103

7

R610

R612

R613

CN19

13

10

1

C1713

CN19

14

14

1

C1714

R614

R615

R616

C1716

R617

C1719

GND

J104

5

C172

1

D1701

C1725

D1702

D1703

C1727

D1704

C1728

D170

5

R170

1

C1729

R1702

D1706

D1707

R1704

D170

8

J105

5

J105

7

R1707

GND

J1058

IC1703

D171

0

IC1704

IC1705

D171

2

D1713D1714

D1715

GHJ1062

D1716

R171

3

D1717

GLJ1065

D1719

IFSJ1067

C603

J1068

R1718

C604

HOT-

GND

J106

9

C605

R1719

C606

C607

D172

0

C609

D172

1

L160

1

52

811

L1603

R1720

2 5

811

L1604

R1722

GND

J107

3

R1724

J107

5

GND

J107

8

GND

J108

0

R1730

R1732

BL-S

WJ1

083

J108

5

J108

6

R664

R665

R667

R668

R174

0

R669

R1744

PWM-SELJ1095

R1745

R1746

R1747

GND

J109

8

R670

R1748

R671

R672

R679

R680

R681

R685 R687

C651

C652

C654

C657

C658

C659

C660

C663

C665

D606

C666

D607

D608

C668

D609

D610

C670

D611

D614

D615

IC601

1

3

5

6

7

9

10

11

12

13

1415

16

T601

J1100

C1201

C1202

C1204

Q120

1Q1202

C1207

C1208

CN16

01

C140

2

BC12

01

D651

Q140

1

D652

Q140

2

Q140

3

C1408

Q140

4

D656

D657D658

1

212

13

CN18

01

D659

C160

1

1CN1802

C160

2

CN1803

F1601

FH1603

C160

3

CN1804

C160

4

FH1604

Q160

1

C1411

C1605

Q1602

C160

7

C160

8

D661

C1609

D662

D664

D665

D666

C1802

D667

C161

0

D668

Q180

1

D1205

C1806

C1612

R120

2

D1207

C1807

C1613

R1203

C161

4

R120

4

C1617

D671

IC12

01

D140

1

D140

2

D672

IC1202

D673

D674

D675

D676

RL1201

D1215

R1214

+

-

D160

1

D1602

R1216

D1603

D160

4

D160

5

R160

1

D1606

D160

7

R160

4

D160

8

R1410

R1605

D1609

R141

1

R160

6

R160

9

D1610

R1226

R142

4

R1436

R1437

R143

8

T1201

R144

0

R144

1

Q601

Q602

BC60

2

J100

4

C110

1

J100

8

J100

9

C1105

J101

0

J101

2

J101

3

J101

4

SA1601

SA16

02

345V

J1017

Q652

Q653

AB

CD

E

123456

COLD

HOT

HOT

HOTHOT

COLD

COLD

COLD

P-ON

3.3

V

GND

GND

LCD

+12

VLCD

+12

VGND

LCD+12V

LCD+12V

GND

GND

P-ON+3.3V

+6.5Vfor1V

GND

GND

GND

GND

GND

P-ON3.5V forREG

P-ON+5.0V

24VforAMP

10:GND

8:P-ON-H17:P-ON-H26:PWR RESET5:BL-ADJ4:BL-SW3:PROTECT12:PROTECT31:GND

24V

GND

ERROR

BL-SW

BL-ADJ

PWM-SEL

11:GND

T 8A H/250V

D613

D1208

J108

7

J105

6

D660

TUNER+35V

HOT+

17V

J101

6

CSJ1015

J108

4HO

T-GN

D

HOT-

GND

J110

5

HOT-

GND

J102

5

HOT-

GND

J102

4

HOT-

GND

J102

3

J103

8

J104

0

J110

6

J110

7

VINA

C

J103

9

J1109

J1108

HOT-

GND

HOT-

GND

HOT-

GND

HOT-

GND

P-ON

3.5V

forR

EG

J106

6

15

J1102

J1011

J1060GND

J1007

D1102

GND

GND

D1101

GNDJ1111

J1005

12:ALL+4.3V13:ALL+4.3V

C1209

D1206

ALL+4.3V

9:GND

ALL+4.3V

GNDJ1113

J1103

RL+5

.0V

J111

4

RL+5.0V

L160

2

J111

5

GND

GND

J111

6

J112

1

J112

0

J111

8

J107

2 J111

9

345V

J104

8

345V

J104

9

345V

J105

0

345V

J104

2

J112

4GN

D

J112

5

GND

GND

GND

+12V

J103

27.

0Vfo

r1V_

DCDC

HOT-

GND

J102

9

J1104

J1043

J107

0LC

D+12

V

J1071

LCD+

12V

J111

7LC

D+12

V

HOT+

17V

J105

2

HOT-GND

J1127

J111

0GN

D

HOT-

GND

J111

2

HOT-

GND

J103

1

D1801

GND

J109

7

J1130

D670

J105

1

J112

3

GND

J1063

GND

J112

2GN

D

P-ON

+3.3

V

J107

7

Q654

R676

R677

GND

J107

9

J110

1

GNDJ1126

GND

GNDGN

D

GND

C110

2

J1131

J1132

D1722

J1059

J107

4

J1054

J107

6

J1128HOT-GND

SD

INV+24V

INV+24V

ALL+

4.3V

J1134

GND

J103

4

HOT-

GND

J100

2

P-ON-H2

J1030

J1082GNDJ1129

HOT-GND

J1093

D1802

P-ON

-H2

J1018

POWE

R-RE

SET

J101

9

JS18

02

JS18

03

ERRORJ1096

BL-ADJ

JS1801

D1106

R1201

C1606

C1413 J1139

D1210

PROTECT1J1091

P-ON

+3.3

VJ1

064

PROTECT1

J109

0

GNDJ1041

J1046GND

GNDJ1099

J113

6

J113

7

C161

8C161

9

C1620 C1621

D120

9

D1211

HOT-

GND

J113

5

GND

J106

1GN

DJ1

081

J113

8

PROT

ECT3

J114

0

C1211

BC1202

BC1203

C1212

C1213

T1701

VDD

GNDC1734

C1735

BC1701

BC1702

BC1703

BC1704

INV+

24V

GND

D120

2

D1204

D1203

D1201

HS16

03

HS16

02

HS16

01

HS17

01

HS601

HS65

2

HS17

14

HS1722

HS17

02

D1723

Power Supply CBA Top ViewBecause a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing.Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.

BA01P0F01033



CAUTION ! :

ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.8A 250V

CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1601) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.

R69

9

10-16

HOT-GND J1020

HOT-GND J1022

HOT-GND J1027

C1702

C1703

D1103

C1704

D1104

Q1701

Q1702

C1706

R607

Q1703

R608

Q1704

R609

Q1705

Q1706

+12V

J1033

Q1707

Q1708

J1035

PWMCTRLJ1037

R610 R612

R613

CN1913

10

1

C1713

CN1914

14

1

C1714

R614

R615

R616

C1716

R617

C1719

GND

J1045

C1721

D1701

C1725

D1702

D1703

C1727

D1704

C1728

D1705

R1701

C1729

R1702

D1706

D1707

R1704

D1708

J1055

J1057

R1707

GNDJ1058

IC1703

D1710

IC1704

IC1705

D1712

D1713

D1714D1715

GHJ1062

D1716

R1713

D1717

GLJ1065

D1719

IFSJ1067

C603

J1068

R1718

C604

HOT-GNDJ1069

C605

R1719

C606

C607

D1720

C609

D1721

L1601

25

8 11

L1603

R1720

25

8 11

L1604

R1722

GNDJ1073

R1724

J1075

GNDJ1078

GNDJ1080

R1730

R1732

BL-SWJ1083

J1085

J1086

R664

R665

R667

R668

R1740

R669

R1744

PWM-SEL J1095

R1745

R1746

R1747

GND

J1098

R670

R1748

R671

R672

R679

R680

R681

R685R687

C651

C652

C654

C657

C658

C659

C660

C663

C665

D606

C666

D607

D608

C668

D609

D610

C670

D611

D614

D615

IC601

1

3

5

6

7

9

10

11

12

13

1415

16

T601

J1100

C1201

C1202

C1204

Q1201 Q1202

C1207

C1208

CN1601

C1402

BC1201

D651

Q1401

D652

Q1402

Q1403

C1408

Q1404

D656

D657 D658

1

212

13

CN1801

D659

C1601

1CN1802

C1602

CN1803

F1601

FH1603

C1603

CN1804

C1604

FH1604

Q1601

C1411

C1605

Q1602

C1607

C1608

D661

C1609

D662

D664

D665

D666

C1802

D667

C1610

D668

Q1801

D1205

C1806

C1612

R1202

D1207

C1807

C1613

R1203

C1614

R1204

C1617

D671

IC1201

D1401

D1402

D672

IC1202

D673

D674

D675

D676

RL1201

D1215

R1214

+

-

D1601

D1602

R1216

D1603D1604

D1605

R1601

D1606

D1607

R1604

D1608

R1410

R1605

D1609

R1411 R1606

R1609

D1610

R1226

R1424

R1436

R1437

R1438

T1201

R1440 R1441

Q601

Q602

BC602

J1004

C1101

J1008

J1009

C1105

J1010

J1012

J1013

J1014

SA1601

SA1602

345V

J1017

Q652

Q653

AB

CD

E

1 2 3 4 5 6

COLD

HOT

HOT

HOTHOT

COLD

COLD

COLD

P-ON 3.3V

GND

GND

LCD +12V

LCD +12V

GND

LCD+12V

LCD+12V

GND

GND

P-ON+3.3V

+6.5Vfor1V

GND

GND

GND

GND

GND

P-ON3.5V forREG

P-ON+5.0V

24VforAMP

10:GND

8:P-ON-H17:P-ON-H2

6:PWR RESET5:BL-ADJ4:BL-SW

3:PROTECT12:PROTECT3

1:GND

24V

GND

ERROR

BL-SW

BL-ADJ

PWM-SEL

11:GND

T 8A H/250V

D613

D1208

J1087

J1056

D660

TUNER+35V

HOT+17V

J1016

CSJ1015

J1084HOT-GND

HOT-GNDJ1105

HOT-GNDJ1025

HOT-GNDJ1024

HOT-GNDJ1023

J1038

J1040

J1106 J1107

VINAC

J1039

J1109

J1108HOT-GND

HOT-GND

HOT-GND

HOT-GND

P-ON3.5VforREG

J1066

15

J1102

J1011

J1060GND

J1007

D1102

GND

GND

D1101

GNDJ1111

J1005

12:ALL+4.3V13:ALL+4.3V

C1209

D1206

ALL+4.3V

9:GND

ALL+4.3V

GNDJ1113

J1103

RL+5.0V

J1114

RL+5.0V

L1602

J1115

GND

GNDJ1116

J1121

J1120

J1118

J1072

J1119

345VJ1048

345VJ1049

345VJ1050

345V

J1042

J1124GND

J1125

GND

GND

GND

+12VJ1032

7.0Vfor1V_DCDC

HOT-GNDJ1029

J1104

J1043

J1070LCD+12V

J1071LCD+12VJ1117LCD+12V

HOT+17VJ1052

HOT-GND

J1127

J1110GND

HOT-GNDJ1112

HOT-GNDJ1031

D1801

GNDJ1097

J1130

D670

J1051

J1123

GND

J1063GND

J1122GND

P-ON+3.3V

J1077

Q654

R676

R677

GNDJ1079

J1101

GNDJ1126

GND

GND

GND GND

C1102

J1131

J1132

D1722

J1059

J1074

J1054

J1076

J1128HOT-GND

SD

INV+24V

INV+24V

ALL+4.3V

J1134

GND

J1034

HOT-GND

J1002

P-ON-H2

J1030

J1082GND J1129

HOT-GND

J1093

D1802

P-ON-H2J1018

POWER-RESET

J1019

JS1802

JS1803

ERRORJ1096

BL-ADJ

JS1801

D1106

R1201

C1606

C1413J1139

D1210

PROTECT1J1091

P-ON+3.3VJ1064

PROTECT1

J1090

GNDJ1041

J1046GND

GNDJ1099

J1136

J1137

C1618

C1619

C1620C1621

D1209

D1211HOT-GNDJ1135

GND

J1061GND

J1081J1138

PROTECT3

J1140

C1211

BC1202

BC1203

C1212

C1213

T1701

VDD

GNDC1734

C1735

BC1701

BC1702

BC1703

BC1704

INV+24V

GND

D1202

D1204

D1203

D1201

HS1603

HS1602

HS1601

HS1701

HS601

HS652

HS1714

HS1722

HS1702

D1723

1 6

18

16

1 10

1120

9

C1701C1705

R1101R1102

C1707

R1103

C1708

R1104

C1709

R1105

R1106

R1107

C1710

C1711

C1712

R1110

C1715

C1717

C1718

C1720

C1722

C1723

C1726

R1703

R1705

R1706

R1708

R1709

C1731

IC1702

C1732

C1733

R1710

R1711

R1712

R1714

R1715

R1716R1717

R1725

R1726

R1727

R1728

R1729

R1731

R1734R1735

R1736

R1737R1738

R1739

R662R663

R1741

R1742

R1743

R673

R674

R675

R682

R683

R686 R688

R689R690

R692

C662

C664

C1203

C1205

C1206

C1401

C1403

C1404

C1405

C1406

C1407

C1409

C1410

C1412

C1414

C1415C1416

C1417

C1803C1804

C1805

C1808

C1809

R1205

R1206

R1401

C1811

C1812

R1402C1813

R1403

C1814

R1404

R1210

R1405

R1406

R1407

R1408

IC1401

R1409

R1603

R1412

R1607

R1413

R1414

R1415

R1416

R1417

R1418

R1801

R1419

R1802

R1803

R1804

R1805

R1806

R1807

R1808

R1420R1421

R1422

R1423

R1425

R1426

R1427

R1428

R1429

R1430

R1431

R1432

R1433

9341

R43

41R

C1104

C1106

R1209

R611

R604

R603

R602

R601

C1210

R1108

D1711

D1709

Power Supply CBA Bottom ViewBecause a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing.Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.

BA01P0F01033



CAUTION ! :

ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.8A 250VCAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1601) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.

10-17

T O O L N O .

1 2 3 4 5 6 7 8 9 1 0

C7A3

A3

BA01P0F0102 3

B

C 7 A 3 A 3

P O W E R S T A N B Y

B A 0 1 P 0 F 0 1 0 2 3 Z

G N D

R C V - I N

A L L + 3 . 3 V

C 7 A 3 A 3


B A 0 1 P 0 F 0 1 0 2 3 Z

G N D

R C V - I N

A L L + 3 . 3 V

C 7 A 3 A 3

P O W E RS T A N B Y

B A 0 1 P 0 F 0 1 0 2 3 C

BA01P0F0102 3D

G N DR C V - I NA L L + 3 . 3 V

L I G H T - S E N S .


K E Y - I N 1L E D - RL E D 1 ( 5 V )

1234567

C 7 A 3 A 3


B A 0 1 P 0 F 0 1 0 2 3 Z

G N D

R C V - I N

A L L + 3 . 3 V

C 7A3 A3

B A 0 1 P 0 F 0 1 0 2 3 E

BA01P0F0102 3 A

3000only

A B C E

2

D

3

A B C EDA B C ED

1

4

5

C 2 1 5 8

SW2151

VOL DOWN

SW2152

VOL UP

SW2153

MENU

SW2154

CH DOWN

SW2155

CH UP

SW2156

POWER

D 2 1 5 2

R2155

R2156

R2157

R2158

R2159

R2160

R2161

W H 2 1 5 1

12

CN002

R S 0 0 1

C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12

CN002

R S 0 0 1

C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12

CN2151

C2151

D 2 1 5 1 D 2 1 5 3

R 2 1 5 1

WH2152

WH2153

WH2154

R S 2 1 5 1

71

71

21

D 2 1 5 4

D 2 1 5 5

D 2 1 5 6

R2165

CN002

R S 0 0 1C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12

2 8

2 91

22 8

2 9 1

2

J K 2 7 0 2

J K 2 7 0 5

J K 2 7 0 6

J K 2 7 0 7

J K 2 7 0 8

J K 2 7 0 9

C N 2 1 0 1

C N 2 1 0 2 C N 2 1 0 3

C N 2 1 0 4

CN2106

C 2 1 0 1

Q2101

Q 2 1 0 2

C 2 3 0 5

B C 2 3 0 1

C2311

D2101

C2703

Q2701

J2801

T U 2 3 0 1

BC2802

BC2803

BC2804

D2301

BC2805

D2302

B C 2 7 0 1

BC2702

L2801

L2802

C 2 7 5 2

C 2 7 5 3

L2803

C 2 7 6 2

C 2 7 6 3

Q 2 4 0 1

C N 2 8 0 1

W H 2 1 0 1

W H 2 1 0 2

C 2 8 0 5

Q 2 8 0 1

C 2 8 0 6

Q 2 8 0 2

Q 2 8 0 3

Q 2 8 0 4

Q 2 8 0 5

D2402

D2403

D2404

D2406

D2408

D2409

D2801

C2631

C2632

D2803

C2828

D2804

Q2632

C2639

L2302R 2 8 0 7

R 2 8 0 8

C2832

C2833

C2644

C 2 8 3 8

C 2 6 4 5

C2839

C2646

C 2 6 4 7

C 2 6 4 8

C2649

C2650

L2701

L 2 7 0 2

D 2 6 3 1

D 2 6 3 2

D2633

R2825

R2633

D2638

R2635

R 2 8 2 9

R2636

R2637

R2655

J2101

C2841 J 2 2 0 6

J2208

J2211

J 2 2 1 3

J 2 2 1 5

J2216

J2218

J 2 2 2 0

J 2 2 2 1

J 2 2 2 2

J 2 2 2 6J2227

J 2 2 2 9

J2231

J2232

J2234

J 2 2 3 5

J2236

J2238

J2240

J 2 2 4 1

J2249

J 2 2 5 4

J 2 2 6 4

J2267

J 2 2 7 0

J2275

J 2 2 7 7

J 2 2 7 8

J 2 2 8 1

J2282

J 2 2 8 3

J2284

J2285

J 2 2 8 7

J 2 2 9 4 J2296

J2298

J 2 3 0 0J 2 3 0 1

J 2 3 0 3J 2 3 0 4

J2305

J 2 3 0 6

J2307

J2308

J 2 3 0 9J 2 3 1 1

J 2 3 1 4J 2 3 1 5

J 2 3 1 7J 2 3 1 8

J 2 3 1 9

J 2 3 2 1 J2322

J2324

J 2 3 0 2

J 2 2 9 2

J 2 2 9 0

J2207

KEY-IN1

G N D

G N D

GND

24V for AMP

J2260

J2269

J2276

J 2 2 5 9

J 2 2 6 8

J 2 2 6 5

J2258

J 2 2 6 2

GND

ALL+4.0V

P-ON+5.0V

LCD+12V

J2273

J2272

J2271

G N D

P - O N + 3 . 3 V

A L L + 3 . 3 V

BL-SW

BL-ADJ

G N D

G N D

P - O N + 8 . 2 V

GND

G N D

J 2 2 9 7 G N D

G N D

S D A

A L L + 3 . 3 V

A L L + 3 . 3 V

P - O N + 5 . 0 V

S D A

S C L

G N D

P - O N - H 2

A L L + 3 . 3 V

+ 3 2 V

LCD+12V

S D A

S C L

G N D

G N D

G N D

GND

R-OUT

G N D

J2102

L 2 3 0 4

J2244

J2239J K 2 7 0 4 J K 2 7 0 3

J2295GND

J 2 2 2 8

G N D

G N D

J2219

J 2 2 2 5

G N D

J2326

J 2 3 2 8

R2837

D2805

C2843

C 2 8 4 2

R2812

C2831

C2830

J 2 3 2 0A - M U T E

C 2 8 4 4

D 2 8 0 2

J2331

7 1

J 2 2 8 0

J 2 3 1 6 2 4 V f o r A M P

J 2 3 1 2

G N D

J 2 3 1 3 P - O N + 3 . 3 V

J 2 2 6 6

S 1 - S WJ 2 2 6 1

S 1 - Y

J 2 2 4 3V 2 - L

G N D

J 2 3 2 7

J 2 2 1 7

S C L

J2204

J 2 2 6 3

S 1 - C

J 2 2 5 3

J 2 2 5 7

J2332

J2245

G N DJ 2 2 0 2

LED-R

GND

GND

GND

G N D

G N D

GND

G N D

J 2 2 9 3

P - O N + 5 . 0 V

J 2 2 4 2G N D

J 2 2 4 6

V I D E O 1

J2224

P-ON+5.0V

J 2 2 5 6

S 1 - S W

J 2 2 9 9L C D + 1 2 V

J 2 2 2 3

2 4 V f o r A M P

J 2 2 5 1

S 1 - YJ 2 2 4 8

S 2 - S W

J 2 3 3 3

J2279

J2330

J 2 3 3 4

J 2 3 3 5 G N D

G N D

J2336

GND

G N DJ 2 3 3 7

J 2 3 3 8 G N D

J2339

GND

GND

J2340

J2214

J K 2 7 1 4

J K 2 7 0 1

J K 2 7 1 5

J K 2 8 0 1

J K 2 7 1 6

J K 2 8 0 2

J K 2 7 1 0

J K 2 7 2 0J K 2 7 2 1

J K 2 7 1 1

GND

J2205

J2210

J2230

J2233

ALL+3.3V

D2407

D2405

R2634

J2341

J 2 2 5 0

V I D E O 2

J 2 2 5 2

S 1 - C

J 2 2 4 7 V 2 - R

J2209

P-ON+11V

GND

J2212

J2237

J2203

GND

D2102 L

IGHT SENS

C2123

J2201GND

D 2 1 0 3

D 2 1 0 4

24VforAMP

G N D

24VforAMP

G N D

GND

GND

GND

2 4 V

P-ON+12V

P-ON+12V

P - O N + 8 . 0 V

P-ON+8.0V

D-AMP

STBY

ALL+4.3V

G N D

G N D

L E D - R

BL-SW

PROTECT3 P-ON+5.0V

P - O N + 5 V

P-ON+5V

P - O N + 5 V

P - O N + 5 V

P-ON+5V

GND

P-ON+5.0V

A - M U T E

LED1

5V

V1-L

V1-R

C N 2 8 0 2

J 2 3 4 2

G N D

J 2 3 2 9

J 2 3 2 3G N D

G N D

11 5

1

1 5

BA01P0F01023

Jack CBA, Function CBA, IR Sensor CBA, Junction-A CBA & Junction-B CBA Top View[40MF430B/F7 (Serial No.:DS1A), LC407SS1 (Serial No.:DS1A, DS2A), LC407EM1]

Jack CBA

Function CBA

IR Sensor CBAJunction-A CBA

Junction-B CBA

Not Used

10-18

ABCE

2

D

3

ABCE D ABCE D

1

4

5

C 2 1 5 8

SW2151

VOL DOWN

SW2152

VOL UP

SW2153

MENU

SW2154

CH DOWN

SW2155

CH UP

SW2156

POWER

D 2 1 5 2

R2155

R2156

R2157

R2158

R2159

R2160

R2161

W H 2 1 5 1

1 2

CN002

R S 0 0 1

C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12CN002

R S 0 0 1

C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12

CN2151

C2151

D 2 1 5 1D 2 1 5 3

R 2 1 5 1

WH2152

WH2153

WH2154

R S 2 1 5 1

71

71

21

D 2 1 5 4

D 2 1 5 5

D 2 1 5 6

R2165C

N002

R S 0 0 1

C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12

2 8

2 91

22 8

2 91

2

J K 2 7 0 2

J K 2 7 0 5

J K 2 7 0 6

J K 2 7 0 7

J K 2 7 0 8

J K 2 7 0 9

C N 2 1 0 1

C N 2 1 0 2C N 2 1 0 3

C N 2 1 0 4

CN2106

C 2 1 0 1

Q2101

Q 2 1 0 2

C 2 3 0 5

B C 2 3 0 1

C2311

D2101

C2703

Q2701

J2801

T U 2 3 0 1

BC2802

BC2803

BC2804

D2301

BC2805

D2302

B C 2 7 0 1

BC2702

L2801

L2802

C 2 7 5 2

C 2 7 5 3

L2803

C 2 7 6 2

C 2 7 6 3

Q 2 4 0 1

C N 2 8 0 1

W H 2 1 0 1

W H 2 1 0 2

C 2 8 0 5

Q 2 8 0 1

C 2 8 0 6

Q 2 8 0 2

Q 2 8 0 3

Q 2 8 0 4

Q 2 8 0 5

D2402

D2403

D2404

D2406

D2408

D2409

D2801

C2631 C2632

D2803

C2828

D2804

Q2632

C2639

L2302

R 2 8 0 7

R 2 8 0 8

C2832

C2833

C2644

C 2 8 3 8

C 2 6 4 5

C2839

C2646

C 2 6 4 7

C 2 6 4 8

C2649

C2650

L2701

L 2 7 0 2

D 2 6 3 1

D 2 6 3 2

D2633

R2825

R2633

D2638

R2635

R 2 8 2 9

R2636

R2637

R2655

J2101

C2841

J 2 2 0 6

J2208

J2211

J 2 2 1 3

J 2 2 1 5

J2216

J2218

J 2 2 2 0

J 2 2 2 1

J 2 2 2 2

J 2 2 2 6

J2227

J 2 2 2 9

J2231

J2232

J2234

J 2 2 3 5

J2236

J2238

J2240

J 2 2 4 1

J2249

J 2 2 5 4

J 2 2 6 4

J2267

J 2 2 7 0

J2275

J 2 2 7 7

J 2 2 7 8

J 2 2 8 1

J2282

J 2 2 8 3

J2284

J2285

J 2 2 8 7

J 2 2 9 4

J2296 J2298

J 2 3 0 0 J 2 3 0 1

J 2 3 0 3 J 2 3 0 4

J2305

J 2 3 0 6

J2307 J

2308

J 2 3 0 9J 2 3 1 1

J 2 3 1 4J 2 3 1 5

J 2 3 1 7J 2 3 1 8

J 2 3 1 9

J 2 3 2 1

J2322

J2324

J 2 3 0 2

J 2 2 9 2

J 2 2 9 0

J2207

KEY-IN1

G N D

G N D

GND

24V for AMP

J2260

J2269

J2276

J 2 2 5 9

J 2 2 6 8

J 2 2 6 5

J2258

J 2 2 6 2

GND

ALL+4.0V

P-ON+5.0V

LCD+12V

J2273

J2272

J2271

G N D

P - O N + 3 . 3 V

A L L + 3 . 3 V

BL-SW

BL-ADJ

G N D

G N D

P - O N + 8 . 2 V

GND

G N D

J 2 2 9 7G N D

G N D

S D A

A L L + 3 . 3 V

A L L + 3 . 3 V

P - O N + 5 . 0 V

S D A

S C L

G N D

P - O N - H 2

A L L + 3 . 3 V

+ 3 2 V

LCD+12VS D A

S C L

G N D

G N D

G N D

GND

R-OUT

G N D

J2102

L 2 3 0 4

J2244

J2239

J K 2 7 0 4J K 2 7 0 3

J2295

GND

J 2 2 2 8

G N D

G N D

J2219

J 2 2 2 5

G N D

J2326

J 2 3 2 8

R2837

D2805

C2843

C 2 8 4 2

R2812

C2831

C2830

J 2 3 2 0A - M U T E

C 2 8 4 4

D 2 8 0 2

J2331

71

J 2 2 8 0

J 2 3 1 62 4 V f o r A M P

J 2 3 1 2

G N D

J 2 3 1 3P - O N + 3 . 3 V

J 2 2 6 6

S 1 - S WJ 2 2 6 1

S 1 - Y

J 2 2 4 3V 2 - L

G N D

J 2 3 2 7

J 2 2 1 7

S C L

J2204

J 2 2 6 3

S 1 - C

J 2 2 5 3

J 2 2 5 7

J2332

J2245

G N D J 2 2 0 2

LED-R

GND

GND

GND

G N D

G N D

GND

G N D

J 2 2 9 3

P - O N + 5 . 0 V

J 2 2 4 2G N D

J 2 2 4 6

V I D E O 1

J2224

P-ON+5.0V

J 2 2 5 6

S 1 - S W

J 2 2 9 9L C D + 1 2 V

J 2 2 2 3

2 4 V f o r A M P

J 2 2 5 1

S 1 - YJ 2 2 4 8

S 2 - S W

J 2 3 3 3

J2279

J2330

J 2 3 3 4

J 2 3 3 5G N D

G N D

J2336

GND

G N DJ 2 3 3 7

J 2 3 3 8G N D

J2339

GND

GND

J2340

J2214

J K 2 7 1 4

J K 2 7 0 1

J K 2 7 1 5

J K 2 8 0 1

J K 2 7 1 6

J K 2 8 0 2

J K 2 7 1 0

J K 2 7 2 0 J K 2 7 2 1

J K 2 7 1 1

GND

J2205

J2210

J2230

J2233

ALL+3.3V

D2407

D2405

R2634

J2341

J 2 2 5 0

V I D E O 2

J 2 2 5 2

S 1 - C

J 2 2 4 7V 2 - R

J2209

P-ON+11V

GND

J2212

J2237

J2203

GND

D2102

LIGHT SENS

C2123

J2201

GND

D 2 1 0 3

D 2 1 0 4

24VforAMP

G N D

24VforAMP

G N D

GND

GND

GND

2 4 V

P-ON+12V

P-ON+12V

P - O N + 8 . 0 V

P-ON+8.0V

D-AMP

STBY

ALL+4.3V

G N D

G N D

L E D - R

BL-SW

PROTECT3

P-ON+5.0V

P - O N + 5 V

P-ON+5V

P - O N + 5 V

P - O N + 5 V

P-ON+5V

GND

P-ON+5.0V

A - M U T E

LED1

5V

V1-L

V1-R

C N 2 8 0 2

J 2 3 4 2

G N D

J 2 3 2 9

J 2 3 2 3G N D

G N D

11 5

1

1 5

C002 C003

C004

C005

C006

C007

R002

R003

R004

R005

C002 C003

C004

C005

C006

C007

R002

R003

R004

R005

C2152

C2153

C2154

C2155

C 2 1 5 6

C2159

R2152

R2153

R2154

R2163

C 2 1 5 7R2166

C002 C003

C004

C005

C006

C007

R002

R003

R004

R005

C2102

C2103

C2104

C2105C2106

C2107

C2301

C 2 3 0 2

C2303

C2304

C2306

C2307

C2308

C2309

C2117

C2118

C2119

C2120

C2121

C2124

C2701

C2125

C2702

C2126

C2127

C2704

C2128

C2705

C2129

C2706

C2707

R2104

C2708

C2709

R2106

C2130

C2710

R2301

C2711

R2302

C2712

C2713

R2304

C2714

R2305

C2715

R2306

C2716

C2717

C2718

C2719

C2720

C2721

C2722

C2723

C2724

C2725

C2726

R2122

C2727

C2728

R2701

R2702

R2703

R2704

R2705

R2706

R2707

R2708

IC

27

01

C2733

C2734

C2735

C2736

C2737

R2710

C2738

R2712

R2713

R2714

R2715

R2716

R2717

R2718

R2719

C2745

C2746

C2747

R2720

C2748

R2721

42

72

R3

27

2R

R2725

R2726

R2727

C2750

R2728

C2751

R2729

C2754

C2755

C2756

C2757

C2758

R2730

C2759

R2731

R2732 R2733

R2734

R2735

R2736

C2760

C2761C2764

C2765

R2743

R2744

R2745

R2746

R2747

R2748

R2755

R2756

R2757

R2758

R2759

R2760

R2762

R2763

R2764

R2765

R2767

R2769

R2770 R2771

C2401

C2402

C2801

C2802

C2803

C2804

C2807

C2808

C2809

C2810

C2811

C2812

C2813

R2403

C2814

R2404

R 2 4 0 5

C2815

R2406

C2816

C2817

R2407

C2818

C2819

C2820

C2821

C2822

C2823

C2824

C2825

C2826

C2827

C2633

C2634

C2829

C2635

R2801

C2636

R2802

R2803

R2804

L2301

R2805

R2806

L2303

IC2801

R2809

C2834

C2835

C2642

C2836

C2837

R2810

R2811

R2813

R2814

R2815

R2816

R2817

R2818

C2840

R2819

R2820

R2821

R2822

R2823

R2826

R2827

R2828

I C 2 6 3 1

R2830

R2831

R2832

R2833

R2835

R2834

R2824

C2766

R2766

R2768

R2772

R2101

R2105

R2103

R2102

R2838

IC2802

R2107

C2845

C2849

C2848

C2846

C2847

R2839

R2840

R2108

C2850

C2122

C2312

C2314

C2313

1

1 3

1 4

2 62 7

3 9

4 0

5 2

1

85

4

3 03 1

1 11 0

4 0

1 2 0

2 1

WF1 WF3PIN 12 OF CN2103

PIN 8 OF CN2103

WF3WF2PIN 10 OF CN2103

WF4PIN 20 OF CN2103

BA01P0F01023

Jack CBA, Function CBA, IR Sensor CBA, Junction-A CBA & Junction-B CBA Bottom View[40MF430B/F7 (Serial No.:DS1A), LC407SS1 (Serial No.:DS1A, DS2A), LC407EM1]

Jack CBA

Function CBA

IR Sensor CBA Junction-A CBA

Junction-B CBA

Not Used

10-19

T O O L N O .

1 2 3 4 5 6 7 8 9 1 0

C7A3

A3

BA01P0F0102 3

B

C 7 A 3 A 3


B A 0 1 P 0 F 0 1 0 2 3 Z

G N D

R C V - I N

A L L + 3 . 3 V

C 7 A 3 A 3


B A 0 1 P 0 F 0 1 0 2 3 Z

G N D

R C V - I N

A L L + 3 . 3 V

C 7 A 3 A 3

P O W E RS T A N B Y

B A 0 1 P 0 F 0 1 0 2 3 C

BA01P0F0102 3D

G N DR C V - I NA L L + 3 . 3 V



K E Y - I N 1L E D - RL E D 1 ( 5 V )

1234567

C 7 A 3 A 3


B A 0 1 P 0 F 0 1 0 2 3 Z

G N D

R C V - I N

A L L + 3 . 3 V

C 7A3 A3

B A 0 1 P 0 F 0 1 0 2 3 E

BA01P0F0102 3 A

3000only

A B C E

2

D

3

A B C EDA B C ED

1

4

5

C 2 1 5 8

SW2151

VOL DOWN

SW2152

VOL UP

SW2153

MENU

SW2154

CH DOWN

SW2155

CH UP

SW2156

POWER

D 2 1 5 2

R2155

R2156

R2157

R2158

R2159

R2160

R2161

W H 2 1 5 1

12

CN002

R S 0 0 1

C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12

CN002

R S 0 0 1

C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12

CN2151

C2151

D 2 1 5 1 D 2 1 5 3

R 2 1 5 1

WH2152

WH2153

WH2154

R S 2 1 5 1

71

71

21

D 2 1 5 4

D 2 1 5 5

D 2 1 5 6

R2165

CN002

R S 0 0 1

C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12

2 8

2 91

22 8

2 9 1

2

J K 2 7 0 2

J K 2 7 0 5

J K 2 7 0 6

J K 2 7 0 7

J K 2 7 0 8

J K 2 7 0 9

C N 2 1 0 1

C N 2 1 0 2 C N 2 1 0 3

C N 2 1 0 4

CN2106

C 2 1 0 1

Q2101

Q 2 1 0 2

C 2 3 0 5

B C 2 3 0 1

C2311

D2101

C2703

Q2701

J2801

T U 2 3 0 1

BC2802

BC2803

BC2804

D2301

BC2805

D2302

B C 2 7 0 1

BC2702

L2801

L2802

C 2 7 5 2

C 2 7 5 3

L2803

C 2 7 6 2

C 2 7 6 3

Q 2 4 0 1

C N 2 8 0 1

W H 2 1 0 1

W H 2 1 0 2

C 2 8 0 5

Q 2 8 0 1

C 2 8 0 6

Q 2 8 0 2

Q 2 8 0 3

Q 2 8 0 4

Q 2 8 0 5

D2402

D2403

D2404

D2406

D2408

D2409

D2801

C2631

C2632

D2803

C2828

D2804

Q2632

C2639

L2302R 2 8 0 7

R 2 8 0 8

C2832

C2833

C2644

C 2 8 3 8

C 2 6 4 5

C2839

C2646

C 2 6 4 7

C 2 6 4 8

C2649

C2650

L2701

L 2 7 0 2

D 2 6 3 1

D 2 6 3 2

D2633

R2825

R2633

D2638

R2635

R 2 8 2 9

R2636

R2637

R2655

J2101

C2841 J 2 2 0 6

J2208

J2211

J 2 2 1 3

J 2 2 1 5

J2216

J2218

J 2 2 2 0

J 2 2 2 1

J 2 2 2 2

J 2 2 2 6J2227

J 2 2 2 9

J2231

J2232

J2234

J 2 2 3 5

J2236

J2238

J2240

J 2 2 4 1

J2249

J 2 2 5 4

J 2 2 6 4

J2267

J 2 2 7 0

J2275

J 2 2 7 7

J 2 2 7 8

J 2 2 8 1

J2282

J 2 2 8 3

J2284

J2285

J 2 2 8 7

J 2 2 9 4 J2296

J2298

J 2 3 0 0J 2 3 0 1

J 2 3 0 3J 2 3 0 4

J2305

J 2 3 0 6

J2307

J2308

J 2 3 0 9J 2 3 1 1

J 2 3 1 4J 2 3 1 5

J 2 3 1 7J 2 3 1 8

J 2 3 1 9

J 2 3 2 1 J2322

J2324

J 2 3 0 2

J 2 2 9 2

J 2 2 9 0

J2207

KEY-IN1

G N D

G N D

GND

24V for AMP

J2260

J2269

J2276

J 2 2 5 9

J 2 2 6 8

J 2 2 6 5

J2258

J 2 2 6 2

GND

ALL+4.0V

P-ON+5.0V

LCD+12V

J2273

J2272

J2271

G N D

P - O N + 3 . 3 V

A L L + 3 . 3 V

BL-SW

BL-ADJ

G N D

G N D

P - O N + 8 . 2 V

GND

G N D

J 2 2 9 7 G N D

G N D

S D A

A L L + 3 . 3 V

A L L + 3 . 3 V

P - O N + 5 . 0 V

S D A

S C L

G N D

P - O N - H 2

A L L + 3 . 3 V

+ 3 2 V

LCD+12V

S D A

S C L

G N D

G N D

G N D

GND

R-OUT

G N D

J2102

L 2 3 0 4

J2244

J2239J K 2 7 0 4 J K 2 7 0 3

J2295GND

J 2 2 2 8

G N D

G N D

J2219

J 2 2 2 5

G N D

J2326

J 2 3 2 8

R2837

D2805

C2843

C 2 8 4 2

R2812

C2831

C2830

J 2 3 2 0A - M U T E

C 2 8 4 4

D 2 8 0 2

J2331

7 1

J 2 2 8 0

J 2 3 1 6 2 4 V f o r A M P

J 2 3 1 2

G N D

J 2 3 1 3 P - O N + 3 . 3 V

J 2 2 6 6

S 1 - S WJ 2 2 6 1

S 1 - Y

J 2 2 4 3V 2 - L

G N D

J 2 3 2 7

J 2 2 1 7

S C L

J2204

J 2 2 6 3

S 1 - C

J 2 2 5 3

J 2 2 5 7

J2332

J2245

G N DJ 2 2 0 2

LED-R

GND

GND

GND

G N D

G N D

GND

G N D

J 2 2 9 3

P - O N + 5 . 0 V

J 2 2 4 2G N D

J 2 2 4 6

V I D E O 1

J2224

P-ON+5.0V

J 2 2 5 6

S 1 - S W

J 2 2 9 9L C D + 1 2 V

J 2 2 2 3

2 4 V f o r A M P

J 2 2 5 1

S 1 - YJ 2 2 4 8

S 2 - S W

J 2 3 3 3

J2279

J2330

J 2 3 3 4

J 2 3 3 5 G N D

G N D

J2336

GND

G N DJ 2 3 3 7

J 2 3 3 8 G N D

J2339

GND

GND

J2340

J2214

J K 2 7 1 4

J K 2 7 0 1

J K 2 7 1 5

J K 2 8 0 1

J K 2 7 1 6

J K 2 8 0 2

J K 2 7 1 0

J K 2 7 2 0J K 2 7 2 1

J K 2 7 1 1

GND

J2205

J2210

J2230

J2233

ALL+3.3V

D2407

D2405

R2634

J2341

J 2 2 5 0

V I D E O 2

J 2 2 5 2

S 1 - C

J 2 2 4 7 V 2 - R

J2209

P-ON+11V

GND

J2212

J2237

J2203

GND

D2102 L

IGHT SENS

C2123

J2201GND

D 2 1 0 3

D 2 1 0 4

24VforAMP

G N D

24VforAMP

G N D

GND

GND

GND

2 4 V

P-ON+12V

P-ON+12V

P - O N + 8 . 0 V

P-ON+8.0V

D-AMP

STBY

ALL+4.3V

G N D

G N D

L E D - R

BL-SW

PROTECT3 P-ON+5.0V

P - O N + 5 V

P-ON+5V

P - O N + 5 V

P - O N + 5 V

P-ON+5V

GND

P-ON+5.0V

A - M U T E

LED1

5V

V1-L

V1-R

C N 2 8 0 2

J 2 3 4 2

G N D

J 2 3 2 9

J 2 3 2 3G N D

G N D

11 5

1

1 5

BA01P0F01023

Jack CBA

Function CBA

IR Sensor CBANot Used

Not Used

Not Used

Jack CBA, Function CBA & IR Sensor CBA Top View [40MF430B/F7 (Serial No.:DS2A), LC407SS1 (Serial No.:DS3A)]

10-20

ABCE

2

D

3

ABCE D ABCE D

1

4

5

C 2 1 5 8

SW2151

VOL DOWN

SW2152

VOL UP

SW2153

MENU

SW2154

CH DOWN

SW2155

CH UP

SW2156

POWER

D 2 1 5 2

R2155

R2156

R2157

R2158

R2159

R2160

R2161

W H 2 1 5 1

1 2

CN002

R S 0 0 1

C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12CN002

R S 0 0 1

C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12

CN2151

C2151

D 2 1 5 1D 2 1 5 3

R 2 1 5 1

WH2152

WH2153

WH2154

R S 2 1 5 1

71

71

21

D 2 1 5 4

D 2 1 5 5

D 2 1 5 6

R2165C

N002

R S 0 0 1

C001

D 0 0 1

D 0 0 2

WH002

R 0 0 1

61

12

2 8

2 91

22 8

2 91

2

J K 2 7 0 2

J K 2 7 0 5

J K 2 7 0 6

J K 2 7 0 7

J K 2 7 0 8

J K 2 7 0 9

C N 2 1 0 1

C N 2 1 0 2C N 2 1 0 3

C N 2 1 0 4

CN2106

C 2 1 0 1

Q2101

Q 2 1 0 2

C 2 3 0 5

B C 2 3 0 1

C2311

D2101

C2703

Q2701

J2801

T U 2 3 0 1

BC2802

BC2803

BC2804

D2301

BC2805

D2302

B C 2 7 0 1

BC2702

L2801

L2802

C 2 7 5 2

C 2 7 5 3

L2803

C 2 7 6 2

C 2 7 6 3

Q 2 4 0 1

C N 2 8 0 1

W H 2 1 0 1

W H 2 1 0 2

C 2 8 0 5

Q 2 8 0 1

C 2 8 0 6

Q 2 8 0 2

Q 2 8 0 3

Q 2 8 0 4

Q 2 8 0 5

D2402

D2403

D2404

D2406

D2408

D2409

D2801

C2631 C2632

D2803

C2828

D2804

Q2632

C2639

L2302

R 2 8 0 7

R 2 8 0 8

C2832

C2833

C2644

C 2 8 3 8

C 2 6 4 5

C2839

C2646

C 2 6 4 7

C 2 6 4 8

C2649

C2650

L2701

L 2 7 0 2

D 2 6 3 1

D 2 6 3 2

D2633

R2825

R2633

D2638

R2635

R 2 8 2 9

R2636

R2637

R2655

J2101

C2841

J 2 2 0 6

J2208

J2211

J 2 2 1 3

J 2 2 1 5

J2216

J2218

J 2 2 2 0

J 2 2 2 1

J 2 2 2 2

J 2 2 2 6

J2227

J 2 2 2 9

J2231

J2232

J2234

J 2 2 3 5

J2236

J2238

J2240

J 2 2 4 1

J2249

J 2 2 5 4

J 2 2 6 4

J2267

J 2 2 7 0

J2275

J 2 2 7 7

J 2 2 7 8

J 2 2 8 1

J2282

J 2 2 8 3

J2284

J2285

J 2 2 8 7

J 2 2 9 4

J2296 J2298

J 2 3 0 0 J 2 3 0 1

J 2 3 0 3 J 2 3 0 4

J2305

J 2 3 0 6

J2307 J

2308

J 2 3 0 9J 2 3 1 1

J 2 3 1 4J 2 3 1 5

J 2 3 1 7J 2 3 1 8

J 2 3 1 9

J 2 3 2 1

J2322

J2324

J 2 3 0 2

J 2 2 9 2

J 2 2 9 0

J2207

KEY-IN1

G N D

G N D

GND

24V for AMP

J2260

J2269

J2276

J 2 2 5 9

J 2 2 6 8

J 2 2 6 5

J2258

J 2 2 6 2

GND

ALL+4.0V

P-ON+5.0V

LCD+12V

J2273

J2272

J2271

G N D

P - O N + 3 . 3 V

A L L + 3 . 3 V

BL-SW

BL-ADJ

G N D

G N D

P - O N + 8 . 2 V

GND

G N D

J 2 2 9 7G N D

G N D

S D A

A L L + 3 . 3 V

A L L + 3 . 3 V

P - O N + 5 . 0 V

S D A

S C L

G N D

P - O N - H 2

A L L + 3 . 3 V

+ 3 2 V

LCD+12VS D A

S C L

G N D

G N D

G N D

GND

R-OUT

G N D

J2102

L 2 3 0 4

J2244

J2239

J K 2 7 0 4J K 2 7 0 3

J2295

GND

J 2 2 2 8

G N D

G N D

J2219

J 2 2 2 5

G N D

J2326

J 2 3 2 8

R2837

D2805

C2843

C 2 8 4 2

R2812

C2831

C2830

J 2 3 2 0A - M U T E

C 2 8 4 4

D 2 8 0 2

J2331

71

J 2 2 8 0

J 2 3 1 62 4 V f o r A M P

J 2 3 1 2

G N D

J 2 3 1 3P - O N + 3 . 3 V

J 2 2 6 6

S 1 - S WJ 2 2 6 1

S 1 - Y

J 2 2 4 3V 2 - L

G N D

J 2 3 2 7

J 2 2 1 7

S C L

J2204

J 2 2 6 3

S 1 - C

J 2 2 5 3

J 2 2 5 7

J2332

J2245

G N D J 2 2 0 2

LED-R

GND

GND

GND

G N D

G N D

GND

G N D

J 2 2 9 3

P - O N + 5 . 0 V

J 2 2 4 2G N D

J 2 2 4 6

V I D E O 1

J2224

P-ON+5.0V

J 2 2 5 6

S 1 - S W

J 2 2 9 9L C D + 1 2 V

J 2 2 2 3

2 4 V f o r A M P

J 2 2 5 1

S 1 - YJ 2 2 4 8

S 2 - S W

J 2 3 3 3

J2279

J2330

J 2 3 3 4

J 2 3 3 5G N D

G N D

J2336

GND

G N DJ 2 3 3 7

J 2 3 3 8G N D

J2339

GND

GND

J2340

J2214

J K 2 7 1 4

J K 2 7 0 1

J K 2 7 1 5

J K 2 8 0 1

J K 2 7 1 6

J K 2 8 0 2

J K 2 7 1 0

J K 2 7 2 0 J K 2 7 2 1

J K 2 7 1 1

GND

J2205

J2210

J2230

J2233

ALL+3.3V

D2407

D2405

R2634

J2341

J 2 2 5 0

V I D E O 2

J 2 2 5 2

S 1 - C

J 2 2 4 7V 2 - R

J2209

P-ON+11V

GND

J2212

J2237

J2203

GND

D2102

LIGHT SENS

C2123

J2201

GND

D 2 1 0 3

D 2 1 0 4

24VforAMP

G N D

24VforAMP

G N D

GND

GND

GND

2 4 V

P-ON+12V

P-ON+12V

P - O N + 8 . 0 V

P-ON+8.0V

D-AMP

STBY

ALL+4.3V

G N D

G N D

L E D - R

BL-SW

PROTECT3

P-ON+5.0V

P - O N + 5 V

P-ON+5V

P - O N + 5 V

P - O N + 5 V

P-ON+5V

GND

P-ON+5.0V

A - M U T E

LED1

5V

V1-L

V1-R

C N 2 8 0 2

J 2 3 4 2

G N D

J 2 3 2 9

J 2 3 2 3G N D

G N D

11 5

1

1 5

C002 C003

C004

C005

C006

C007

R002

R003

R004

R005

C002 C003

C004

C005

C006

C007

R002

R003

R004

R005

C2152

C2153

C2154

C2155

C 2 1 5 6

C2159

R2152

R2153

R2154

R2163

C 2 1 5 7R2166

C002 C003

C004

C005

C006

C007

R002

R003

R004

R005

C2102

C2103

C2104

C2105C2106

C2107

C2301

C 2 3 0 2

C2303

C2304

C2306

C2307

C2308

C2309

C2117

C2118

C2119

C2120

C2121

C2124

C2701

C2125

C2702

C2126

C2127

C2704

C2128

C2705

C2129

C2706

C2707

R2104

C2708

C2709

R2106

C2130

C2710

R2301

C2711

R2302

C2712

C2713

R2304

C2714

R2305

C2715

R2306

C2716

C2717

C2718

C2719

C2720

C2721

C2722

C2723

C2724

C2725

C2726

R2122

C2727

C2728

R2701

R2702

R2703

R2704

R2705

R2706

R2707

R2708

IC

27

01

C2733

C2734

C2735

C2736

C2737

R2710

C2738

R2712

R2713

R2714

R2715

R2716

R2717

R2718

R2719

C2745

C2746

C2747

R2720

C2748

R2721

42

72

R3

27

2R

R2725

R2726

R2727

C2750

R2728

C2751

R2729

C2754

C2755

C2756

C2757

C2758

R2730

C2759

R2731

R2732 R2733

R2734

R2735

R2736

C2760

C2761C2764

C2765

R2743

R2744

R2745

R2746

R2747

R2748

R2755

R2756

R2757

R2758

R2759

R2760

R2762

R2763

R2764

R2765

R2767

R2769

R2770 R2771

C2401

C2402

C2801

C2802

C2803

C2804

C2807

C2808

C2809

C2810

C2811

C2812

C2813

R2403

C2814

R2404

R 2 4 0 5

C2815

R2406

C2816

C2817

R2407

C2818

C2819

C2820

C2821

C2822

C2823

C2824

C2825

C2826

C2827

C2633

C2634

C2829

C2635

R2801

C2636

R2802

R2803

R2804

L2301

R2805

R2806

L2303

IC2801

R2809

C2834

C2835

C2642

C2836

C2837

R2810

R2811

R2813

R2814

R2815

R2816

R2817

R2818

C2840

R2819

R2820

R2821

R2822

R2823

R2826

R2827

R2828

I C 2 6 3 1

R2830

R2831

R2832

R2833

R2835

R2834

R2824

C2766

R2766

R2768

R2772

R2101

R2105

R2103

R2102

R2838

IC2802

R2107

C2845

C2849

C2848

C2846

C2847

R2839

R2840

R2108

C2850

C2122

C2312

C2314

C2313

1

1 3

1 4

2 62 7

3 9

4 0

5 2

1

85

4

3 03 1

1 11 0

4 0

1 2 0

2 1

WF1 WF3PIN 12 OF CN2103

PIN 8 OF CN2103

WF3WF2PIN 10 OF CN2103

WF4PIN 20 OF CN2103

BA01P0F01023

Jack CBA, Function CBA & IR Sensor CBA Bottom View [40MF430B/F7 (Serial No.:DS2A), LC407SS1 (Serial No.:DS3A)]

Jack CBA

Function CBA

IR Sensor CBA Not Used

Not Used

Not Used

WAVEFORMS

FL10.5WF11-1

Input: NTSC Color Bar Signal (with 1kHz Audio Signal)

WF1 ~ WF4 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.)

CVBSCVBS 0.2V0.2V 2020ms

WF1 Pin 8 of CN2103

S-VIDEO-YS-VIDEO-Y 0.2V0.2V 2020ms

S-VIDEO-CS-VIDEO-C 0.2V0.2V

WF3 Pin 12 of CN2103

2020ms

AUDIOAUDIO 1V1V 0.5m0.5ms

COMPONENT-PrCOMPONENT-Pr 0.2V0.2V 2020msms

COMPONENT-Pb COMPONENT-Pb 0.2V0.2V 2020ms

Pin 10 of CN2103WF2

COMPONENT-YCOMPONENT-Y 0.2V0.2V 2020ms

(VIDEO IN)

(S-VIDEO IN)

(COMPONENT IN)

(S-VIDEO IN)

(COMPONENT IN)

Pin 20 of CN2103WF4

FL10.5WI12-1

WIRING DIAGRAM

CN

1601

21

AC

601

AC

CO

RD

AC

IN

LET

CL1

914

CL1

601

CL2

101

CN

1914

11P

RO

TE

CT

310

GN

D9

GN

D

14N

U13

BAC

KLIG

HT-

ADJ

12BA

CKL

IGH

T-SW

8G

ND

7G

ND

6G

ND

5PA

NE

L+24

V4

PAN

EL+

24V

3PA

NE

L+24

V2

PAN

EL+

24V

1PA

NE

L+24

V

PO

WE

R S

UP

PLY

CB

A

JAC

K C

BA

CN

2106

CL2

106

CN

1801

JUN

CT

ION

-B

CB

A

CN

2101

CN

1802

WH

2102

WH

2101

DIG

ITA

L M

AIN

CB

A U

NIT

CN

2102

CN

3701

CN

2103

CN

3702

CN

3902

1

5

3

9

7

2

4

6

8

10

14

12

18

16

11

13

15

17

19

23

2120

LCD+12VLCD+12VLCD+12VLCD+12VGNDGNDGNDGNDGNDGNDLVDS-D4E(+)LVDS-D4E(-)LVDS-D3E(+)LVDS-D3E(-)GNDLVDS-ECLK(+)LVDS-ECLK(-)GNDLVDS-D2E(+)LVDS-D2E(-)LVDS-D1E(+)LVDS-D1E(-)LVDS-D0E(+)

22

24 LVDS-D0E(-)25 GND26 SPI-RD/CTRL127 RESET28 SPI-WR/CTRL229 SPI-CS/CTRL3

CN

3901

30

34

32

38

36

31

33

35

37

39

43

41

47

45

40

42

44

46

48

5049

SCL/CTRL4SDA/CTRL5GNDSPI-CLKSELLVDSLVDS-D4O(+)LVDS-D4O(-)LVDS-D3O(+)LVDS-D3O(-)GNDLVDS-OCLK(+)LVDS-OCLK(-)GNDLVDS-D2O(+)LVDS-D2O(-)LVDS-D1O(+)LVDS-D1O(-)LVDS-D0O(+)LVDS-D0O(-)GNDGNDGND51

HD

MI-

CO

NN

EC

TO

R-1

HD

MI-

CO

NN

EC

TO

R-2

HD

MI-

CO

NN

EC

TO

R-3

LC

D M

OD

UL

E A

SS

EM

BLY

CL3100

32

4

USB(-)USB(+)GND

1 USB+5V

US

B J

AC

K

JUN

CT

ION

-A

CB

A

IR

SE

NS

OR

C

BA

FU

NC

TIO

N

CB

A

CN

2151

CL2

155

CL2

153

CN

2104

WH

2154

WH

2153

WH

2151

WH

2152

CL2

801

CL2

802

SP

2801

SP

EA

KE

RL-

CH

SP

2802

SP

EA

KE

RR

-CH

1C

N28

01

2S

P(L

)-S

P(L

)+

1C

N28

02

2S

P(R

)-S

P(R

)+

TU

NE

R U

NIT

11

TU

NE

R+

35V

33

LCD

+12

V2

2LC

D+

12V

44

GN

D5

5G

ND

66

P-O

N+

3.3V

77

GN

D8

8P

-ON

+7.

5V

1010

P-O

N+

3.5V

99

GN

D

1111

GN

D12

12P

-ON

+5V

1313

GN

D14

14A

MP

+24

V15

15G

ND

11

TU

NE

R+

35V

33

LCD

+12

V2

2LC

D+

12V

44

GN

D5

5G

ND

66

P-O

N+

3.3V

77

GN

D8

8P

-ON

+7.

5V

1010

P-O

N+

3.5V

99

GN

D

1111

GN

D12

12P

-ON

+5V

1313

GN

D14

14A

MP

+24

V15

15G

ND

113

AL+

4.3V

311

GN

D2

12A

L+4.

3V

410

GN

D5

9G

ND

68

P-O

N-H

1

95

BAC

KLIG

HT-

ADJ

104

BAC

KLIG

HT-

SW11

3P

RO

TE

CT

112

2P

RO

TE

CT

313

1G

ND

77

P-O

N-H

28

6P

OW

ER

-RE

SE

T

11

KE

Y-IN

1

33

LED

12

2LE

D-R

44

AL+

3.3V

55

RE

MO

TE

66

GN

D7

7LI

GH

T-S

EN

SO

R

11

KE

Y-IN

12

2G

ND

11

KE

Y-IN

1

33

LED

12

2LE

D-R

44

AL+

3.3V

55

RE

MO

TE

66

GN

D7

7LI

GH

T-S

EN

SO

R

23

19

21

15

17

22

20

18

16

14

10

12

6

8

13

11

9

7

5

1

34

1

5

3

9

7

2

4

6

8

10

14

12

18

16

11

13

15

17

19

23

2120

2IF-AGCGNDDIF-OUT1DIF-OUT2LED-RP-ON-H1RESETPROTECT3PROTECT1P-ON-H2P-ON+5VP-ON+5VGNDGNDP-ON+3.5VP-ON+3.5VGNDGNDP-ON+3.3VP-ON+3.3VBACKLIGHT-SWBACKLIGHT-ADJLCD+12V

22

2424 LCD+12V2525 LCD+12V2626 GND2727 GND2828 P-ON+7.5V2929 GND

23

19

21

15

17

22

20

18

16

14

10

12

6

8

13

11

9

7

5

1

34

1

5

3

9

7

2

4

6

8

10

14

12

18

16

11

13

15

17

19

23

2120

2LIGHT-SENSORSPDIFGNDAUDIO(L)-OUTGNDAUDIO(R)-OUTGNDCVBS/Y/S-Y-INGNDPb-INGNDPr/S-C-INGNDAUDIO-MUTEAL+3.3VAL+3.3VSDASCLGNDAUDIO(L)GNDAUDIO(R)REMOTE

22

2424 LED12525 KEY-IN12626 AMP(L)-OUT2727 GND2828 AMP(R)-OUT2929 GND

CL2102

CL2103

AUDIO(R)-IN1

VIDEO-IN2

VIDEO-IN1

AUDIO(L)-IN1

AUDIO(R)-IN2

AUDIO(L)-IN2

S-VIDEO-IN1

S-VIDEO-IN2

HDMI-AUDIO(L)-IN

HDMI-AUDIO(R)-IN

COMPONENT-AUDIO(L)-IN

COMPONENT-AUDIO(R)-IN

AUDIO(L)-OUT

AUDIO(R)-OUT

DIGITAL-AUDIO-OUT (COAXIAL)

COMPONENT-Y-IN

COMPONENT-Pb-IN

COMPONENT-Pr-IN


FL10.5WI_212-2

CN

1601

21

AC

601

AC

CO

RD

AC

IN

LET

CL1

914

CL1

601

CL2

101

CN

1914

11P

RO

TE

CT

310

GN

D9

GN

D

14BA

CKL

IGH

T-AD

J13

NU

12BA

CKL

IGH

T-SW

8G

ND

7G

ND

6G

ND

5PA

NE

L+24

V4

PAN

EL+

24V

3PA

NE

L+24

V2

PAN

EL+

24V

1PA

NE

L+24

V

PO

WE

R S

UP

PLY

CB

A

JAC

K C

BA

CN

2106

CL2

106

CN

1801

CN

1802

WH

2102

DIG

ITA

L M

AIN

CB

A U

NIT

CN

2102

CN

3701

CN

2103

CN

3702

CN

3902

1

5

3

9

7

2

4

6

8

10

14

12

18

16

11

13

15

17

19

23

2120

LCD+12VLCD+12VLCD+12VLCD+12VGNDGNDGNDGNDGNDGNDLVDS-D4E(+)LVDS-D4E(-)LVDS-D3E(+)LVDS-D3E(-)GNDLVDS-ECLK(+)LVDS-ECLK(-)GNDLVDS-D2E(+)LVDS-D2E(-)LVDS-D1E(+)LVDS-D1E(-)LVDS-D0E(+)

22

24 LVDS-D0E(-)25 GND26 SPI-RD/CTRL127 RESET28 SPI-WR/CTRL229 SPI-CS/CTRL3

CN

3901

30

34

32

38

36

31

33

35

37

39

43

41

47

45

40

42

44

46

48

5049

SCL/CTRL4SDA/CTRL5GNDSPI-CLKSELLVDSLVDS-D4O(+)LVDS-D4O(-)LVDS-D3O(+)LVDS-D3O(-)GNDLVDS-OCLK(+)LVDS-OCLK(-)GNDLVDS-D2O(+)LVDS-D2O(-)LVDS-D1O(+)LVDS-D1O(-)LVDS-D0O(+)LVDS-D0O(-)GNDGNDGND51

HD

MI-

CO

NN

EC

TO

R-1

HD

MI-

CO

NN

EC

TO

R-2

HD

MI-

CO

NN

EC

TO

R-3

LC

D M

OD

UL

E A

SS

EM

BLY

CL3100

32

4

USB(-)USB(+)GND

1 USB+5V

US

B J

AC

K

IR

SE

NS

OR

C

BA

FU

NC

TIO

N

CB

A

CL2

155

CL2

153

CN

2104

WH

2154

WH

2151

WH

2152

CL2

801

CL2

802

SP

2801

SP

EA

KE

RL-

CH

SP

2802

SP

EA

KE

RR

-CH

1C

N28

01

2S

P(L

)-S

P(L

)+

1C

N28

02

2S

P(R

)-S

P(R

)+

TU

NE

R U

NIT

11

TU

NE

R+

35V

33

LCD

+12

V2

2LC

D+

12V

44

GN

D5

5G

ND

66

P-O

N+

3.3V

77

GN

D8

8P

-ON

+7.

5V

1010

P-O

N+

3.5V

99

GN

D

1111

GN

D12

12P

-ON

+5V

1313

GN

D14

14A

MP

+24

V15

15G

ND

113

AL+

4.3V

311

GN

D2

12A

L+4.

3V

410

GN

D5

9G

ND

68

P-O

N-H

1

95

BAC

KLIG

HT-

ADJ

104

BAC

KLIG

HT-

SW11

3P

RO

TE

CT

112

2P

RO

TE

CT

313

1G

ND

77

P-O

N-H

28

6P

OW

ER

-RE

SE

T

11

KE

Y-IN

1

33

LED

12

2LE

D-R

44

AL+

3.3V

55

RE

MO

TE

66

GN

D7

7LI

GH

T-S

EN

SO

R

11

KE

Y-IN

12

2G

ND

23

19

21

15

17

22

20

18

16

14

10

12

6

8

13

11

9

7

5

1

34

1

5

3

9

7

2

4

6

8

10

14

12

18

16

11

13

15

17

19

23

2120

2IF-AGCGNDDIF-OUT1DIF-OUT2LED-RP-ON-H1RESETPROTECT3PROTECT1P-ON-H2P-ON+5VP-ON+5VGNDGNDP-ON+3.5VP-ON+3.5VGNDGNDP-ON+3.3VP-ON+3.3VBACKLIGHT-SWBACKLIGHT-ADJLCD+12V

22

2424 LCD+12V2525 LCD+12V2626 GND2727 GND2828 P-ON+7.5V2929 GND

23

19

21

15

17

22

20

18

16

14

10

12

6

8

13

11

9

7

5

1

34

1

5

3

9

7

2

4

6

8

10

14

12

18

16

11

13

15

17

19

23

2120

2LIGHT-SENSORSPDIFGNDAUDIO(L)-OUTGNDAUDIO(R)-OUTGNDCVBS/Y/S-Y-INGNDPb-INGNDPr/S-C-INGNDAUDIO-MUTEAL+3.3VAL+3.3VSDASCLGNDAUDIO(L)GNDAUDIO(R)REMOTE

22

2424 LED12525 KEY-IN12626 AMP(L)-OUT2727 GND2828 AMP(R)-OUT2929 GND

CL2102

CL2103

AUDIO(R)-IN1

VIDEO-IN2

VIDEO-IN1

AUDIO(L)-IN1

AUDIO(R)-IN2

AUDIO(L)-IN2

S-VIDEO-IN1

S-VIDEO-IN2

HDMI-AUDIO(L)-IN

HDMI-AUDIO(R)-IN

COMPONENT-AUDIO(L)-IN

COMPONENT-AUDIO(R)-IN

AUDIO(L)-OUT

AUDIO(R)-OUT

DIGITAL-AUDIO-OUT (COAXIAL)

COMPONENT-Y-IN

COMPONENT-Pb-IN

COMPONENT-Pr-IN

[40MF430B/F7(Serial No.:DS2A), LC407SS1(Serial No.:DS3A)]

13-1 FL10.5CEX

EXPLODED VIEWS

Cabinet [40MF430B/F7 (Serial No. : DS1A), LC407SS1 (Serial No. : DS1A, DS2A), LC407EM1]

A1

L1

A12

L1

L1

L24

See Electrical Parts List for parts with this mark.

Power Supply CBA

B5

IR Sensor CBA

Junction-A CBA

Function CBA

CL1914

SP2801

Jack CBA

B11

A3

A15

SP2802

Stand Assembly


B7

L1

L1

L5

L5

L5

B18

L5

B14

B14

B14

B20

CL2155

S6

L5

L5

L4

A2

L6

L5

L5

L5 CL2106

L1

B11

L7

L4

CL2153

L24

L7

CL2802

CL2801

LCD-1

A11

L2

L8

L1

L1L8

B1

L3

L3

L3

L3 L3

A13

A14S6

B10

B12

L2

L6

L7

L6

B8

B6

B9

B9

CL3100

L2

A5A4

X3301

L1

L4

L1

L1

L6

L8L1

L1L1

L1

A9

X2801

L1

L6

L6

CL2103CL2102

CL2101

Junction-BCBA

CL1601

L7

13-2 FL10.5(A01PE/PFUH)CEX

Cabinet [40MF430B/F7 (Serial No. : DS2A), LC407SS1 (Serial No. : DS3A)]

A1

L1

A12

L1

L1

L24

See Electrical Parts List for parts with this mark.

Power Supply CBA

B5

IR Sensor CBA

Function CBA

CL1914

SP2801

Jack CBA

B11

A3

A15

SP2802

Stand Assembly


B7

L1

L1

L5

L5

L5

B18

L5

B14

B14

B14

B20

CL2155

S6

L5

L5

L4

A2

L6

L5

L5

L5 CL2106

L1

B11

L7

L4

CL2153

L24

L7

CL2802

CL2801

LCD-1

A11

L2

L8

L1

L1L8

B1

L3

L3

L3

L3 L3

A13

A14S6

B10

B12

L2

L6

L7

L6

B8

B6

B9

B9

CL3100

L2

A5A4

X3301

L1

L4

L1

L1

L6

L8L1

L1L1

L1

A9

X2801

L1

L6

L6

CL2103CL2102

CL2101

CL1601

L7

13-2 FL10.5PEX

Packing

PP Band

Packing Tape

Packing Tape

X5

S3

S2

Some Ref. Numbers are not in sequence.

S5

S6

S7

X4

StandAssembly

X2 X6 X8 X7

FRONT

Packing Tape

Packing Tape

S4

S4

S6

Tape

X1X3

AC601

S1

Tape

20100327 14-1 A01PBCA

PARTS LIST [40MF430B/F7]

Mechanical Parts

PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTE: Parts that are not assigned part numbers (---------) are not available.

Ref. No. Description Part No.

STAND ASSEMBLY A01P0UH 1ESA23094

A1 FRONT CABINET A01P0UH 1EM024765A

A2 REAR CABINET A01P0UH 1EM024766

A3 DECORATION PLATE A01PBUH 1EM025606

A4 FUNCTION KNOB A01P0UH 1EM223723

A5 KNOB FRAME A01P0UH 1EM223724

A9 JACK HOLDER(A) A01P0UH 1EM223663

A11 JACK HOLDER(D) A01P3UH 1EM223804

A12# RATING LABEL A01PBUH ----------

A13 JACK LABEL(A) A01P0UH 1EM430477

A14 JACK LABEL(D) A01P0UH 1EM430478

A15 POP LABEL A01P1UH ----------

B1 SHIELD BOX(Z) A01P0UH 1EM124034

B5 STAND BRACKET A01P0UH 1EM024771

B6 WALL MOUNT BRACKET(L) A01P0UH 1EM024773

B7 WALL MOUNT BRACKET(R) A01P0UH 1EM024770

B8 PCB HOLDER(U) A01P0UH 1EM223667

B9 PCB HOLDER(D) A01P0UH 1EM223668

B10 AC INLET HOLDER A01P0UH 1EM327037

B11 SPEAKER HOLDER A01P0UH 1EM124113

B12 JACK PCB HOLDER A01P0UH 1EM124033

B18 GASKET A8AF0UH 1EM425861

CL1601 WIRE ASSEMBLY 2PIN 2PIN/105MM WX1A01P0-207


CL2102 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94H0-101

CL2103 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94H0-101

CL2106 WIRE ASSEMBLY 13PIN FFC 13PIN/120MM WX1A01P0-101



CL3100 WIRE ASSEMBLY LVDS 51PIN/350MM WX1A01P0-306

L1 SCREW P-TIGHT M4X14 BIND HEAD+BLK GBHP4140

L2 SCREW P-TIGHT 3X10 BIND HEAD+ GBHP3100

L4 S-TIGHT SCREW M3X6 BIND HEAD+BLACK GBHS3060

L5 ASSEMBLED SCREW ( D9 M3X6 ) A71F0UH 1EM424392B

L6 SCREW SEMS M4X8 PAN HEAD + FPJ34080

L7 DOUBLE SEMS SCREW M5X8 M5X8 PAN HEAD+

FPJ35080

L8 DOUBLE SEMS SCREW M5X12 BLK M5X12PAN HEAD +BLK

FPH35120

L24 SHOULDER SCREW A01Q0UF 1EM328277

LCD-1 40W TFT-LCD MODULE LK400D3LA14 UDULCD0SH005

SP2801 SPEAKER MAGNETIC S0412F19 DS08120XQ001

SP2802 SPEAKER MAGNETIC S0412F19 DS08120XQ001

X2801 THERMOSTAR TMS-L-2(12*12HC) XK10000X4003

X3301 THERMOSTAR TMS-L-2(12*12HC) XK10000X4003

PACKINGS1 CARTON (U) A01PBUH 1EM328142

S2 CARTON(L) A01P0UH 1EM327137

S3 STYROFOAM TOP A01P0UH 1EM025445

S4 STYROFOAM BOTTOM A01P0UH 1EM025446

S5 SET BAG A91H2UH 1EM325897

S6 SERIAL NO. LABEL A01PBUH ----------

S7 STAND BAG A91H2UH 1EM428517

ACCESSORIESAC601# CORD W/O A GND WIRE UL/CSA/ 162/NO/

BLACKWAV0162LW001

X1 BAG POLYETHYLENE 235X365XT0.03 0EM408420A

X2# OWNERS MANUAL A01PBUH 1EMN26219

X3 REMOTE CONTROL NF804UD NF804UD

X4 DRY BATTERY R03/2S XB0M451T0006

X5 STAND SCREW KIT A01P0UH 1ESA23096

X6 QUICK START GUIDE A01PBUH 1EMN26359

X7 REGISTRATION CARD (MAGNAVOX) A94F0UH

1EMN24699

X8 CHILD SAFETY SHEET A94F0UH 1EMN24439


20100327 14-2 A01PBEL

Electrical Parts


NOTES:

1. Parts that are not assigned part numbers (---------) are not available.

2. Tolerance of Capacitors and Resistors are noted with the following symbols.

DIGITAL MAIN CBA UNIT

POWER SUPPLY CBA

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%


DIGITAL MAIN CBA UNIT A01PBMMA-001


POWER SUPPLY CBAConsists of the following:

A01P1MPW-001

CAPACITORSC603 POLYESTER FILM CAP. (PB FREE) 0.047µF/

100V JCA2A473DT018

C604 CERAMIC CAP. RB 100pF/2KV CA3D101TE006

C605 POLYESTER FILM CAP. (PB FREE) 0.0015µF/100V J

CA2A152DT018


CA2A104DT018


CA2A222DT018

C609 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZNDL102

C651 CERAMIC CAP. BL 1500pF/2KV CA3D152XF003

C652 ELECTROLYTIC CAP. 33µF/50V M CE1JMASDL330

C654 ELECTROLYTIC CAP. 1000µF/35V M CE1GMZNDL102

C657 ELECTROLYTIC CAP. 2200µF/25V M CE1EMZNDL222

C659 ELECTROLYTIC CAP. 2200µF/10V M CE1AMZNDL222

C660 ELECTROLYTIC CAP. 1000µF/10V M CE1AMASDL102

C662 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104



C665 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102


CA2A104DT018

C668# SAFTY CAP. 1000pF/250V KX CA2E102MR101


C1101 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101

C1102 ELECTROLYTIC CAP. 1000µF/16V M CE1CMZNDL102

C1104 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C1105 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0

C1106 CHIP CERAMIC CAP. B K 1200pF/50V CHD1JK30B122

C1201# ELECTROLYTIC CAP 33µF/200V M CE2DMZNDL330

C1202 CAP CERAMIC HV 1000pF/1KV B K CA3A102TE006

C1203 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224




C1208 CAP CERAMIC SL J 15pF/2KV CCD3DJNSL150



C1402 ELECTROLYTIC CAP. 4.7µF/50V M CE1JMASDL4R7

C1403 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224

C1404 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225


C1406 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102









C1415 CHIP CERAMIC CAP.(1608) CH J 22pF/50V CHD1JJ3CH220



C1601# CAP METALIZED FILM 1.0µF/310V /K/LE-MX CTA1050DC001






C1607 CAP METALIZED FILM J1.0µF/630V/J/MPEF CA2K105DT048


C1612 CAP ELECTROLYTIC 150µF/400V/M/25/30 CA2H151DYG18









C1706 CERAMIC CAP. B K 100pF/1KV CCD3AKD0B101





C1711 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474



C1714 CAP METALIZED FILM J0.039µF/630V/J/MPEF CA2K393DT045





C1719 ELECTROLYTIC CAP. 4.7µF/50V M H7 CE1JMAVSL4R7








20100327 14-3 A01PBEL







CONNECTORSCN1601# CONNECTOR B2P3-VH(LF)(SN) J3VH020JG001

CN1801 FFC CONNECTOR IMSA-9615S-13A-PP-A JC96J13ER007

CN1802 242 SERIES CONNECTOR 224202115W1 J322C15TG001

CN1914 CONNECTOR PRINT OSU B14B-PH-K-S(LF)(SN)

J3PHC14JG029

DIODESD606# DIODE ZENER 39BSB-T26 NDTB039BST26

D607# DIODE ZENER 27BSB-T26 NDTB027BST26

D609 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26

D610# DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F


D613 DIODE FAST RECOVERY FR103-B/P NDWZ0FR103BP

D614 DIODE ZENER 24BSB-T26 NDTB024BST26

D615 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F

D651 DIODE FR104-B NDLZ000FR104

D652 DIODE ZENER 1ZB43BB NDWZ0001ZB43

D656 DIODE SHOTTKY SB3200BR NDWZ3200D027

D657 DIODE ZENER 1ZB36BB NDWZ0001ZB36



D662 DIODE SCHOTTKY SB360BH NDWZ000SB360

D664 SHUNT REGULATOR KIA431B-AT/P NSZBA0TJY038

D665 DIODE FAST RECOVERY FR151-B/P NDWZ0FR151BP

D666 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036


D668 SHUNT REGULATOR KIA431B-AT/P NSZBA0TJY038

D670 DIODE SCHOTTKY SB230BD NDWZ000SB230

D672 DIODE SCHOTTKY SB3A0BH NDWZ000SB3A0

D673 DIODE SCHOTTKY SB3A0BH NDWZ000SB3A0



D1102 SCHOTTKY BARRIER DIODE SB240-B/P NDWZ000SB240

D1103 SHUNT REGULATOR KIA2431AP-AT/P NSZBA0TJY054



D1201# DIODE 1N5397BD NDL1001N5397

D1202# DIODE 1N5397BD NDL1001N5397

D1203# DIODE 1N5397BD NDL1001N5397

D1204# DIODE 1N5397BD NDL1001N5397

D1205 DIODE SCHOTTKY BARRIER 1H8-A2 NDTZ0001H8A2








D1402 DIODE ZENER HZS24NB3TE-EQ QDTCHZS24NB3


D1604 DIODE FAST RECOVERY 30PFB60 QDWZ030PFB60


D1606 DIODE FAST RECOVERY 30PFB60 QDWZ030PFB60

D1607# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU








D1706 SCHOTTKY BARRIER DIODE SB140 NDWZ000SB140

D1707 SCHOTTKY BARRIER DIODE SB140 NDWZ000SB140


D1710 DIODE ZENER HZS27NB2TE-EQ QDTBHZS27NB2


D1713 DIODE ZENER HZS27NB4TE-EQ QDTDHZS27NB4



D1720 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036

D1721 DIODE SHOTTKY FCHS20A08 QDWZCHS20A08


ICSIC601# PHOTO COUPLER LTV817MCF NPECLTV817MF

IC1201# IC SWITCHING POWER SUPPLY MIP2F30MSSCF DIP7-A1

QSCA0S0MS012

IC1202# PHOTO COUPLER LTV817MCF NPECLTV817MF

IC1401# IC DUAL-PHASE PFC CONTROLLER HPA00651DR/SOIC

NSCA0T0TY015

IC1702 IC 0V-SWITCHING RESONANT CONVE TEA1611T/N1.518

NSCA0TNXP002




COILSL1601# LINE FILTER 86H-8319B LLEG0ZDEL001

L1602# LINE FILTER 86H-8319B LLEG0ZDEL001

When you replace one of the below Coils on this CBA, please replace with the one that has same parts number.Do not mix different parts number’s Coil.

L1603# COIL EF 9702 LLEE0Z0KT001

L1604# COIL EF 9702 LLEE0Z0KT001

or

L1603# COIL EF JLC2518 LLEE0Z0XB007

L1604# COIL EF JLC2518 LLEE0Z0XB007

TRANSISTORSQ601# MOS FET 2SK3798(Q.M) QFQZSK3798QM

Q602# TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F

Q652 NPN TRANSISTOR POWER 2SC4881F HFE MAX320

QQWZ2SC4881F

Q653 NPN TRANSISTOR POWER 2SC4881F HFE MAX320

QQWZ2SC4881F

Q1201 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P

Q1202 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F

Q1401 TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F

Q1402 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P



Q1601# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q

Q1602# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q

Q1701# FET MOS TK5A50D(FUNAI QEWZTK5A50DQ

Q1702# FET MOS TK5A50D(FUNAI QEWZTK5A50DQ

Q1703 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F






RESISTORSR601 RES CHIP 3216 1/4W J 390k Ω RRX4394HH034

R602 RES CHIP 3216 1/4W J 390k Ω RRX4394HH034




20100327 14-4 A01PBEL

R607 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001


R609# METAL OXIDE FILM RES. 2W J 0.75 Ω RN02R75ZU001

R610 RES CARBON FILM T 1/4W J 100k Ω RCX4104T1001


R612 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001






R662 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223

R663 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332

R669 METAL RESISTER. 2W J 0.56 Ω RN02R56ZU001




R673 RES CHIP.(1608) 1/10W D 10k Ω RRXADR5H1002

R674 RES CHIP.(1608) 1/10W D 1.1k Ω RRXADR5H1101

R675 RES CHIP.(1608) 1/10W D 10k Ω RRXADR5H1002

R679 RES. CARBON FILM J 1/2W J 1.5 Ω RCX21R5T1003



R682 CHIP RES. 1/10W F 3.3k Ω RRXAFR5H3301

R683 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002




R688 CHIP RES. 1/10W F 510 Ω RRXAFR5H5100



R692 CHIP RES. 1/10W F 220 Ω RRXAFR5H2200


R1102 CHIP RES. 1/10W F 51.0 k Ω RRXAFR5H5102



R1105 CHIP RES. 1/10W J 390 Ω RRXAJR5Z0391



R1108 CHIP RES. 1/10W J 2.2 Ω RRXAJR5Z02R2


R1201# METAL OXIDE FILM RES. 2W J 1 Ω RN021R0ZU001








R1214 RES CARBON FILM T 1/4W J 2.2 Ω RCX42R2T1001



R1401 RES CHIP 3216 1/4W F 825k Ω RTC8253HH020














R1414 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000

























R1440 WIRE COPPER 6111-06003-0120 XZ40C0SHG002



R1604 RES CEMENT 5W J 0.022 Ω RWJL22PAK002




R1609 GLASS GLAZE RES. 1/2W J 3.3M Ω RXX2JZLZ0335



















R1719 CEMENT RESISTOR 2W J 0.18 Ω RWJR18PAK001

R1720 CEMENT RESISTOR 2W J 0.18 Ω RWJR18PAK001










20100327 14-5 A01PBEL

JACK ASSEMBLY

JACK CBA





















MISCELLANEOUSB14 POW HEAT SINK A7120UH 1EM423993

B20 HEAT SINK EAJ ASSEMBLY A81H0UH 1EM424644

BC602 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030




BC1701 WIRE COPPER 6111-06003-0120 XZ40C0SHG002




F1601# FUSE 8A/250V(PB FREE) 0215008.MXP PBGZ20BAG022

FH1603 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002

FH1604 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002

JS1801 WIRE COPPER 6111-06003-0120 XZ40C0SHG002

L3 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080

RL1201# RELAY SDT-SS-105DM MRLEC05QN001

SA1601# SURGE ABSORBER 470V+-10PER NVQZ10D471KB

T601# TRANS POWER BCK-35-0742 LTT3PC0XB060

T1201# TRANS POWER 27H-9003D LTT1PCDEL001

T1701# TRANS INV SRX40ER-P240000G8501 LTZ4PZ0TE001


JACK ASSEMBLYConsists of the following:

A01PBMJC-001

JACK CBAJUNCTION-B CBA

-----------------------------------------------------------FUNCTION CBAIR SENSOR CBAJUNCTION-A CBA

A01PBMJC-001-JKJN

-------------------------------------A01PBMJC-001-FNIRJN


JACK CBAConsists of the following:

----------

CAPACITORSC2101 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0








C2123 ELECTROLYTIC CAP. 33µF/16V M H7 CE1CMAVSL330















C2635 CHIP CERAMIC CAP. B K 10µF/10V CHE1AK30B106

C2636 CHIP CERAMIC CAP. CH J 560pF/50V CHD1JJ3CH561





C2647 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101




C2701 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105

C2702 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105

C2703 ELECTROLYTIC CAP. 10µF/50V M H7 CE1JMAVSL100



C2706 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474































20100327 14-6 A01PBEL






C2753 ELECTROLYTIC CAP. 10µF/50V M H7 CE1JMAVSL100








C2763 ELECTROLYTIC CAP. 100µF/10V M H7 CE1AMAVSL101




C2803 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105



























C2832 ELECTROLYTIC CAP. 47µF/25V M H7 CE1EMAVSL470

C2833 ELECTROLYTIC CAP. 47µF/25V M H7 CE1EMAVSL470


C2839 ELECTROLYTIC CAP. 220µF/35V M CE1GMASDL221

C2840 CAP CHIP 3216 B M 10µF/16V CA1C106TE143

C2841 ELECTROLYTIC CAP. 220µF/35V M CE1GMASDL221

C2842 METALIZED POLYESTER FILM CAP. 0.39µF/50V J

CT1J394DT040

C2843 METALIZED POLYESTER FILM CAP. 0.39µF/50V J

CT1J394DT040





CONNECTORSCN2102 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007


CN2104 242 SERIES CONNECTOR 224202107W1 J322C07TG001



CN2801 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN)

J3PHC02JG029

CN2802 CONNECTOR BASE 2P(EH) B 2B-EH-A(LF)(SN)

J3EHC02JG010

DIODESD2402 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133


D2405 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133







D2638 DIODE ZENER 33BSA-T26 NDTA033BST26



D2805 DIODE ZENER 7V5BSC-T26 NDTC7R5BST26

ICSIC2631 IC REGULATOR AZ2940D-3.3TRE1 NSCA0TBCD017

IC2701 IC WIED BROADWIDTH AV SW BH7645KS2 QSCA0R0RM008

IC2801 IC D-CLASS POWER AMPLIFER R2A15122FP-W00R/HQFP

QSCA0T0HT005

IC2802 IC OP AMP NJM4558M(TE1)-#ZZZB QSZBA0TJR089

COILSL2301 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22

L2303 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22

L2304 INDUCTOR 33µH-K-5FT LLARKBSTU330

L2701 WIRE CP STP-S-0.50 XZ40F0REN001


L2801 COIL RADIAL LHLP10NB330M 33µH LLF3300TU003

L2802 COIL RADIAL LHLP10NB330M 33µH LLF3300TU003


TRANSISTORSQ2401 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P








RESISTORSR2101 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103





















20100327 14-7 A01PBEL

JUNCTION-B CBA

R2655 RES. CARBON FILM J 1/2W J 1.0k Ω RCX2102T1003


























































R2812 METAL OXIDE FILM RES. 2W J 6.8 Ω RN026R8ZU001

























R2837 METAL OXIDE FILM RES. 2W J 6.8 Ω RN026R8ZU001


MISCELLANEOUSBC2301 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030

BC2701 WIRE CP STP-S-0.50 XZ40F0REN001







JK2701 JACK RCA PCB S ORANGE 01/RCA-101H(OR) JXRJ010YUQ06

JK2702 JACK SW DIN PCB S 04/DIN-417HA-01 JYEJ040YUQ03

JK2703 JACK RCA PCB S YELLOW 01/RCA-101H(YL) JXRJ010YUQ05

JK2704 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02

JK2705 JACK SW RCA PCB S RED RCA-102H(RD) JYRJ010YUQ03

JK2706 JACK SW DIN PCB L DIN-435C(777D) JYEL040YUQ03

JK2707 JACK RCA PCB L RCA-101S(1)-03 JXRL010YUQ12

JK2708 JACK RCA PCB L RCA-101S(1)-04 JXRL010YUQ13

JK2709 JACK SW RCA PCB L RCA-102F(RD) JYRL010YUQ05


JK2711 JACK SW RCA PCB S RED RCA-102H(RD) JYRJ010YUQ03

JK2714 JACK RCA PCB S GREEN 01/RCA-101H(GN) JXRJ010YUQ03

JK2715 JACK RCA PCB S BLUE 01/RCA-101H(BL) JXRJ010YUQ04

JK2716 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01





TU2301 TUNER UNIT ATSC/NTSC/QAM TDYU4-D02A UTNATS0AL001


JUNCTION-B CBAConsists of the following:

----------

CONNECTORCN2101 242 SERIES CONNECTOR TUC-P15X-B1 WHT

STJCTUB15TG002


20100327 14-8 A01PBEL

FUNCTION CBA

IR SENSOR CBA

JUNCTION-A CBA


FUNCTION CBAConsists of the following:

----------

CAPACITORC2158 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062

DIODED2152 DIODE ZENER 5V1BSB-T26 NDTB5R1BST26

RESISTORSR2155 RES CARBON FILM T 1/4W G 18k Ω RCX4183T1002

R2156 RES CARBON FILM T 1/4W G 8.2k Ω RCX4822T1002




R2160 WIRE CP STP-S-0.50 XZ40F0REN001


SWITCHESSW2151 TACT SWITCH SKQSAB SST0101AL038

SW2152 TACT SWITCH SKQSAB SST0101AL038





MISCELLANEOUSCL2153 WIRE ASSEMBLY 2PIN/250MM WX1A01P0-208


IR SENSOR CBAConsists of the following:

----------

CAPACITORSC2151 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470






DIODESD2151 LED L-53HT NP4Z000L53HT

D2153 LED GREEN 333GT/E(FNA) NPWZ33GTEFNA

D2156 O-E DEVICE PHOTO TRANSISTOR JSA-3113B NPWZJSA3113B

RESISTORSR2151 RES CARBON FILM T 1/4W J 100 Ω RCX4101T1001





R2165 WIRE CP STP-S-0.50 XZ40F0REN001


MISCELLANEOUSB44 SENSOR HOLDER A01Q0UF 1EM328018

CL2155 WIRE ASSEMBLY 7PIN 7PIN/910MM/RED GLAY

WX1A01P0-003

RS2151 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044


JUNCTION-A CBAConsists of the following:

----------

CONNECTORCN2151 242 SERIES CONNECTOR TUC-P07X-B1 WHT

STJCTUB07TG002

20100413 14-9 A01PDCA

PARTS LIST [LC407SS1 (Serial No. : DS2A)]

Mechanical Parts



Different parts from the original model 40MF430B/F7



A3 DECORATION PLATE A01P4UH 1EM025865A

A12# RATING LABEL A01PDUH ----------

S1 CARTON (U) A01P1UH 1EM327299

X2# OWNERS MANUAL A01PDUH 1EMN26439

X3 REMOTE CONTROL NH200UD NH200UD

X6 QUICK START GUIDE A01PDUH 1EMN26440

X7 REGISTRATION CARD (SYLVANIA) A94F1UH 1EMN24700


20100413 14-10 A01PDEL

Electrical Parts


NOTES:




C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%


DIGITAL MAIN CBA UNIT A01P4MMA-001

20100701 14-11 A01PFCA

PARTS LIST [LC407SS1 (Serial No. : DS3A)]

Mechanical Parts






A3 DECORATION PLATE A01P4UH 1EM025865A

A12# RATING LABEL A01PFUH ----------

CL1914 WIRE ASSEMBLY 14PIN 14PIN/240MM/AWG 24

WX1A01P0-213

CL3100 WIRE ASSEMBLY 51PIN 51PIN/370MM/UL1517 WX1A01P0-309

LCD-1 LCD MODULE 40W LTA400HM01 UDULCD0SM006

S1 CARTON (U) A01P1UH 1EM327299

X2# OWNERS MANUAL A01PDUH 1EMN26439

X3 REMOTE CONTROL NH200UD NH200UD

X6 QUICK START GUIDE A01PDUH 1EMN26440

X7 REGISTRATION CARD (SYLVANIA) A94F1UH 1EMN24700


20100701 14-12 A01PFEL

Electrical Parts


NOTES:




C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%


DIGITAL MAIN CBA UNIT A01PFMMA-001

POWER SUPPLY CBA A01PEMPW-001



CN1802 CONNECTOR PRINT OSU B15B-PH-K-S(LF)(SN)

J3PHC15JG029

D656 DIODE SHOTTKY SB3200BR NDWZ3200D027





D1208 DIODE ZENER 1M200Z B0 200V NDLZ001M200Z

R1803 Not used






JS1801 Not used

JS1802 WIRE COPPER 6111-06003-0120 XZ40C0SHG002

JACK ASSEMBLYConsists of the following

A01PEMJC-001

JACK CBA A01PEMJC-001-JK

FUNCTION CBAIR SENSOR CBA

A01PEMJC-001-FNIR

JACK CBA ----------

CL2101 WIRE ASSEMBLY 15PIN 15PIN/195MM/AWG26

WX1A01P0-004

CL2155 WIRE ASSEMBLY 7PIN 7PIN/910MM/AWG26 WX1A01P0-005

CN2104 CONNECTOR PRINT OSU C S B7B-PH-K-S(LF)(S

J3PHC07JG029

JUNCTION-B CBA(In this model, the JUNCTION-B CBA is not used.)

CN2101 Not used

JUNCTION-A CBA(In this model, the JUNCTION-A CBA is not used.)

CN2151 Not used


15-1 FL10.5REV

REVISION HISTORY

Chassis FL10.5• 2010-04-20 40MF430B/F7 (Serial No. : DS1A) added

• 2010-05-06 LC407SS1 (Serial No. : DS2A) added

• 2010-07-22 LC407SS1 (Serial No. : DS3A) added

• TBD LC407SS1 (Serial No. : DS1A) added

• TBD LC407EM1 added

• TBD 40MF430B/F7 (Serial No. : DS2A) added

chassis fl10.5 service manual - encompass · pdf filelcd tv chassis fl10.5 service manual ......

Documents