chest of drawers & tall boy - spacepro · page 1 of 5 spr_instruc_du_tb_05.2016 12x one piece...
TRANSCRIPT
chest of drawers & tall boyAssembly Instructions
SPR_INSTRUC_DU_TB_05.2016www.spacepro.co.uk/instructions-2/Page 1 of 5
12x One piece connectors
(16x for Tall Boy)
4x T-nuts
12x Plastic dowels
(16x for Tall Boy)
18x Euro Screws
(24x for Tall Boy)
Chest of drawers & tall boy contents:A 1x Top panelB 2x Back panels (1x for Tall Boy)C 1x Side panel (left)D 1x Side panel (right)E 1x BaseF 4x LegsG 2x Drawer infills (3x for Tall Boy)H 2x Infill covers (3x for Tall Boy)I 3x Drawer sides (left) (4x for Tall Boy)J 3x Drawer sides (right) (4x for Tall Boy)K 3x Drawer backs (4x for Tall Boy)L 3x Drawer fronts (4x for Tall Boy)M 3x Drawer bases (4x for Tall Boy)N 6x Soft close clips (3x left, 3x right) (8x for Tall Boy, 4x left, 4x right)O 6x Soft close drawer runners (3x left, 3x right) (8x for Tall Boy, 4x left, 4x right)
12x Wood Screws
(16x for Tall Boy)
V1
Chest of drawers
Tall boy
20x Dowels(24x for Tall Boy)
20x Cams
(24x for Tall Boy)
2x Wall mounting
brackets
12x Drawer bottom
support brackets(Chest of
Drawers only)
We recommend you use the Wall Mounting Brackets provided to fix the Chest of Drawers/Tall Boy to a wall (where possible). This will prevent the unit being pulled over. Use suitable fixings.
• Tools: Screwdriver & Hammer• Two person build
Recommended:
SPR_INSTRUC_DU_TB_05.2016www.spacepro.co.uk/instructions-2/Page 2 of 5
3 41 – Insert Cams. 2 – Remove film then attach infill covers.Repeat on both drawer infills.
Fix the Wall Mounting Brackets with the screw provided in the pack.1 2
x6x6
x6
x4
x4
5
Note: C panel shown
Use hammer to tap T-nuts (2) into place.
x2
x2
Ensure the infills are faced towards the bottom.
PLEASE NOTE THE CHEST OF DRAWERS AND TALL BOY ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE CHEST OF DRAWERS AS AN EXAMPLE.
STEP 1 STEP 2
Bottom
x2
SPR_INSTRUC_DU_TB_05.2016www.spacepro.co.uk/instructions-2/Page 3 of 5
9 10Screw through holes shown on both sides. Note: 6x for Chest of Drawers, 8x for Tall Boy.
x6
x4
x12
Lay unit on its back, then insert legs into holes and turn until tight.
6 87 Slide back panel (B) in place.
11
x2
x2
Tap plastic dowels (3) gently into place with a hammer(Repeat on all drawer sides).
SQUEEZE SIDES THEN INSERT
PIN
Note: Tall Boy back panel is one complete panel
FIX THROUGH THESE HOLES
Bottom
Bottom Bottom
PLEASE NOTE THE CHEST OF DRAWERS AND TALL BOY ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE CHEST OF DRAWERS AS AN EXAMPLE.
SPR_INSTRUC_DU_TB_05.2016www.spacepro.co.uk/instructions-2/
15
Page 4 of 5
1
2
12 1413 Repeat on all drawers.
CHEST OF DRAWERS ONLY
PIN
x4 (per drawer)
Push/tap sides (J&I) onto back panel (K).(Repeat on both drawers).
Drawer back
Repeat on all drawers. (Drawer shown from underneath).
1 – Slide the drawers so that the prong goes into the hole in the back of the drawer. 2 – Pull the sliders forward, until you hear a click, repeat on both sides.
PLEASE NOTE THE CHEST OF DRAWERS AND TALL BOY ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE CHEST OF DRAWERS AS AN EXAMPLE.
x4
SPR_INSTRUC_DU_TB_05.2016www.spacepro.co.uk/instructions-2/
We recommend you use the Wall Mounting Brackets provided to fix the Chest of Drawers/Tall Boy to a wall (where possible). This will prevent the unit being pulled over. Use suitable fixings.
WALL MOUNTING BRACKETS
PLEASE NOTE THE CHEST OF DRAWERS AND TALL BOY ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE CHEST OF DRAWERS AS AN EXAMPLE.
Page 5 of 5
Fix the Wall Mounting Bracket to both sides of the Unit(s). (Use suitable fixings when attaching to the wall).
USE SUITABLEWALL FIXINGS