cisco stadiumvision mobile reporter and cisco ... › c › en › us › td › docs ›...

Cisco StadiumVision Mobile Reporter and Cisco StadiumVision Mobile Streamer Installation and Upgrade GuideRelease 1.2.0-507 March 28, 2013 SV-M-REPORTER-K9 SV-M-STREAMER-K9

Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000

800 553-NETS (6387)Fax: 408 527-0883

http://www.cisco.com

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

Cisco StadiumVision Mobile Reporter and Cisco StadiumVision Mobile Streamer Installation and Upgrade Guide © 2013 Cisco Systems, Inc. All rights reserved.

http://www.cisco.com/go/trademarks

Cisco StadiumVision Mobile Repo

C O N T E N T S

Preface iii

Document Purpose iiiDocument Audience iiiRelated Documentation iii

Installing Cisco StadiumVision Mobile Streamer and Cisco StadiumVision Mobile Reporter Software 1

Before You Begin 1Browser, Flash Player, and Java Support for StadiumVision Mobile Reporter and StadiumVision Mobile Streamer 1Hardware Prerequisites 2If you are receiving a Cisco StadiumVision Mobile server for the first time 3

Installing Cisco StadiumVision Mobile Software 4Supported Servers 4Preparing for the Installation 4Confirming the CIMC Firmware Version 5Configuring CIMC 6

Installing Cisco StadiumVision Mobile Software 6Starting CIMC 6

What To Do Next 14

Set the time zone on the StadiumVision Mobile Streamer 14

Start NTP on the StadiumVision Mobile Streamer 15

Configure NTP on the StadiumVision Mobile Reporter 16

Log into the StadiumVision Mobile Reporter TUI 17

Start the Cassandra Service on the StadiumVision Mobile Reporter 17

Set the Date and Time on the StadiumVision Mobile Reporter 17

Set the User Time Zone on the StadiumVision Mobile Reporter 18

Upgrading StadiumVision Mobile Reporter Using the Web Browser UI and TUI 19

Appendix A: CIMC Configuration and Firmware Upgrade Guidelines on the Cisco UCS C220 Server 21

CIMC Initial Configuration 21

Prerequisites 21

CIMC Initial Configuration Summary 22

CIMC Firmware Upgrade Guidelines 23

Before You Begin 23

iiirter and Cisco StadiumVision Mobile Streamer Installation and Upgrade Guide

Contents

Prerequisites 24

CIMC/BIOS Firmware Upgrade Summary 24

ivCisco StadiumVision Mobile Reporter and Cisco StadiumVision Mobile Streamer Installation and Upgrade Guide

Preface

Revised: March 28, 2013Cisco StadiumVision Mobile Release 1.2

Table 1 Document Revision History

Document PurposeThis document describes how to install the StadiumVision Mobile Reporter and StadiumVision Mobile Streamer software on a Cisco UCS C200 or Cisco UCS C220 server.

Document Audience

The intended audience is StadiumVision Mobile Reporter and StadiumVision Mobile Streamer system administrators, Cisco Technical Field Engineers who are responsible for designing and deploying StadiumVision Mobile, and Cisco Partners. It is expected that readers of this document are familiar with basic IP networking and video technology, have a general understanding of the sports and entertainment business, and understand the objectives and operations of live events.

Related DocumentationSee the Cisco StadiumVision Mobile Reporter Administration Guide and Cisco StadiumVision Mobile Streamer Administration Guide for information about operating the StadiumVision Mobile Reporter and StadiumVision Mobile Streamer.

Date Description

March 28, 2013 Initial release of Cisco StadiumVision Mobile.

iiiCisco StadiumVision Mobile Reporter and Cisco StadiumVision Mobile Streamer Installation and Upgrade Guide

PrefaceDocument Purpose

Obtaining Documentation and Submitting a Service RequestFor information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS Version 2.0.

ivCisco StadiumVision Mobile Reporter and Cisco StadiumVision Mobile Streamer Installation and Upgrade Guide

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

P A R T 1

Cisco StadiumVision Mobile Reporter and Cisco StadiumVision Mobile Streamer Installation

Installing Cisco StadiumVision Mobile Streamer and Cisco StadiumVision Mobile Reporter Software

This module provides instructions for installing StadiumVision Mobile Reporter or StadiumVision Mobile Streamer software on both the Cisco UCS C220 and Cisco UCS C200 servers, nd contains the following sections:

• Before You Begin, page 1

• Preparing for the Installation, page 4

• Installing Cisco StadiumVision Mobile Software, page 4

– Preparing for the Installation, page 4

– Confirming the CIMC Firmware Version, page 5

– Configuring CIMC, page 6

– Starting CIMC, page 6

– Log into the StadiumVision Mobile Reporter TUI, page 17

– Set the Date and Time on the StadiumVision Mobile Reporter, page 17

– Upgrading StadiumVision Mobile Reporter Using the Web Browser UI and TUI, page 19

Before You BeginBe sure that you understand and have met the following prerequisites before you begin to install or upgrade the Cisco StadiumVision Mobile hardware.

Browser, Flash Player, and Java Support for StadiumVision Mobile Reporter and StadiumVision Mobile Streamer

You can use an Apple Mac or Microsoft Windows PC or laptop to access the StadiumVision Mobile Streamer configuration and StadiumVision Mobile Reporter marketing and support data. The StadiumVision Reporter configuration Text User Interface (TUI) can be accessed by any SSH client, or by physical console access. describes the method of access.

1Cisco StadiumVision Mobile Reporter and Cisco StadiumVision Mobile Streamer Installation and Upgrade Guide

Installing Cisco StadiumVision Mobile Streamer and Cisco StadiumVision Mobile Reporter SoftwareBefore You Begin

Java Support

To remotely access the CIMC for the software installation, your computer meets the minimum browser and Flash player requirements for Cisco StadiumVision Mobile, and also has Java 1.6 or later installed.

Browser Support

Table 2 describes the browser software versions that have been tested with Cisco StadiumVision Mobile Release 1.2.

Note Unless specifically identified as unsupported, other browser versions might work, but their compatibility with Cisco StadiumVision Mobile cannot be assured.

Hardware Prerequisites

• Connect a monitor and keyboard to the Cisco UCS C220 or Cisco UCS C200. Install the Cisco StadiumVision Mobile software with a hardwired network connection.

• Bring a US keyboard if traveling to a country where English is not the primary language.

• Connect the Cisco UCS C220 or Cisco UCS C200 to the network using the eth0 Ethernet port on the rear panel. Static network addressing should always be used. Have the following information available:

– IPv4 Internet address

– Netmask

– Gateway

– Nameservers

Table 1 Cisco StadiumVision Mobile Component Access Methods

Cisco StadiumVision Mobile Component Access method Type of data

Cisco StadiumVision Mobile Reporter TUI - console access, SSH client Configuration

Cisco StadiumVision Mobile Reporter GUI - browser Marketing and support

Cisco StadiumVision Mobile Streamer GUI - browser Configuration

Cisco StadiumVision Mobile Streamer CLI - console access, SSH client Configuration

Table 2 Tested Browser Software

PC or Laptop OS Browser Version1

1. No additional browser software is tested other than what is listed in this table (for example, not Apple Safari). However, other browser software might work.

Flash Player

Apple Mac OS X • Google Chrome Version 24.0

• Mozilla FireFox Version 18.0.1

Adobe Flash Player Version 11.5.502.146

Microsoft Windows (Windows 7)

• Google Chrome Version 24.0

• Microsoft Internet Explorer Version 9

• Mozilla FireFox Version 18.0.1

Adobe Flash Player Version 11.5.502.146


Installing Cisco StadiumVision Mobile Streamer and Cisco StadiumVision Mobile Reporter SoftwareBefore You Begin

– Hostname

– Proxy if direct internet access is not available

If you are receiving a Cisco StadiumVision Mobile server for the first time

Cisco StadiumVision Mobile software is available in different types of files based on the installation or upgrade environment, as shown in Table 3 and Table 4.

Table 3 Cisco StadiumVision Mobile—Fresh Installation

Table 4 Cisco StadiumVision Mobile—Upgrade

A fresh installation should be performed only if the pre-installed version number is lower than the following versions:

• StadiumVision Mobile Streamer: 1.2.0-21

• StadiumVision Mobile Reporter: 1.2.0-507

When upgrading the StadiumVision Mobile Streamer, consider the following points:

• Upgrades between StadiumVision Mobile Release 1.0 and 1.1 or 1.2 require a full ISO installation upgrade with full OS re-imaging via CIMC for the Cisco UCS C220.

• Streamer builds within Release 1.2 can use RPM upgrades on both the Cisco UCS C220 and Cisco UCS C200.

• Upgrades are performed in the same manner for the StadiumVision Mobile Streamer on the Cisco UCS C220 and Cisco UCS C200 starting with StadiumVision Mobile Release 1.2 build 13.

For detailed instructions on installing or upgrade the StadiumVision Mobile Reporter or StadiumVision Mobile Streamer software, see the Cisco StadiumVision Mobile Reporter and Cisco StadiumVision Mobile Streamer Installation and Upgrade Guide.

Product Platform File to Use Media

StadiumVision Mobile Streamer Cisco UCS C200 Full ISO DVD

Cisco UCS C220 CIMC remote mount

StadiumVision Mobile Reporter Cisco UCS C200 Full ISO DVD

Cisco UCS C220 CIMC remote mount

Product Platform File to Use File upload Initiate Upload

StadiumVision Mobile Streamer Cisco UCS C200 Upgrade ISO

scp (secure copy)

UNIX shell

Cisco UCS C220

StadiumVision Mobile Reporter Cisco UCS C200 Upgrade ISO

Browser TUI1

1. For upgrade instructions using the web browser UI, see the “Upgrading StadiumVision Mobile Reporter Using the Web Browser User Interface” section in the Cisco StadiumVision Mobile Reporter and Cisco StadiumVision Mobile Streamer Installation and Upgrade Guide.

Cisco UCS C220


www.cisco.com/en/US/docs/Sports_Entertainment/StadiumVision/Mobile/software/installation/guide/1_2/svm_reporter_streamer_install_gde.html

www.cisco.com/en/US/docs/Sports_Entertainment/StadiumVision/Mobile/software/installation/guide/1_2/svm_reporter_streamer_install_gde.html

Installing Cisco StadiumVision Mobile Streamer and Cisco StadiumVision Mobile Reporter SoftwareInstalling Cisco StadiumVision Mobile Software

Installing Cisco StadiumVision Mobile SoftwareTo install StadiumVision Mobile Reporter or StadiumVision Mobile Streamer software on a Cisco UCS C220, use the procedures in the following sections in consecutive order:

• Supported Servers, page 4

• Preparing for the Installation, page 4

• Confirming the CIMC Firmware Version, page 5

• Configuring CIMC, page 6

• Starting CIMC, page 6

• Installing Cisco StadiumVision Mobile Software, page 6

• What To Do Next, page 14

Supported ServersCisco StadiumVision Mobile Reporter and Cisco StadiumVision Mobile Streamer are supported on the following platforms:

• Cisco UCS C220—uses Cisco Integrated Management Controller (CIMC) to perform the installation

• Cisco UCS C200—uses a DVD to perform the installation

Preparing for the InstallationThis section provides instructions for configuring CIMC network connectivity for the Cisco UCS C220 server. Download the StadiumVision Mobile ISO file to prepare for the installation after CIMC setup.

Prior to installation:

• Set up the server hardware

• Connect a monitor and keyboard to the StadiumVision Mobile server

• Bring a US keyboard if traveling to a country where English is not the primary language

Cisco UCS C220

• Download the latest ISO image

• Be sure the CIMC firmware is up to date (see Confirming the CIMC Firmware Version, page 5)

• Configure CIMC (see Configuring CIMC, page 6)

Cisco UCS C200

• Have the installation DVD available

• Follow the procedures in the “To install on a Cisco UCS C200, begin installation with the following steps:” section

Connect the StadiumVision Mobile server to the network using the eth0 Ethernet port on the rear panel. Static network addressing should always be used. Have the following information available:

• IPv4 Internet address



• Netmask

• Gateway

• Nameservers

• Hostname

• Proxy if direct internet access is not available

Confirming the CIMC Firmware VersionStep 1 Access CIMC from a web browser using the following credentials:

user: admin password: password

e.g., https://10.194.168.139/login.html

Step 2 Locate the firmware version in the Server Summary screen as shown in Figure 1.

Note 1.4(6d) is the minimum tested CIMC firmware version for Cisco StadiumVision Mobile release 1.2. For instructions on upgrading the CIMC firmware, refer to the Installing the Server chapter in the “Updating the BIOS and CIMC Firmware” section in the Cisco UCS C220 Server Installation and Service Guide.

Figure 1 CIMC Firmware Version Location


http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C220/install/C220.html


Configuring CIMCTo perform the initial CIMC configuration on a Cisco UCS C220, use the procedure described in“Appendix A: CIMC Configuration and Firmware Upgrade Guidelines on the Cisco UCS C220 Server”.

Note If you see a “Media Fail” error message during StadiumVision Mobile Streamer bootup, there is likely a misconfigured RAID controller. Install the Streamer ISO virtual DVD to correct this error. If the RAID controller is configured properly, no error message is expected.

Refer to the Cisco StadiumVision Mobile Release Notes for the latest installation information.

To continue the StadiumVision Mobile installation process, refer to the“Installing Cisco StadiumVision Mobile Software” section on page 6.

Installing Cisco StadiumVision Mobile SoftwareThis section provides instructions for installing StadiumVision Mobile Streamer or StadiumVision Mobile Reporter software on both a Cisco UCS C220 and Cisco UCS C200.

The install program will:

• Automatically set up and initialize the hardware RAID controller 1

• Wipe any existing partitions and zero out the Master Boot Record (MBR)

To start installation on a Cisco UCS C220, follow the procedures in the “Starting CIMC” section.

To start installation on a Cisco UCS C200, follow the procedures in the “To install on a Cisco UCS C200, begin installation with the following steps:” section.

Starting CIMC

Step 1 Access CIMC from a web browser:

e.g., https://IP address/login.html



Step 2 Click the Add Exception button.

Step 3 Click the Confirm Security Exception button to get to the CIMC login page. The default login credentials are:

user: admin password: password



Step 4 Observe the CIMC interface.

Step 5 Verify that the CIMC firmware is the latest version. To verify the firmware version, see Confirming the CIMC Firmware Version, page 5.

Note At this release, 1.4(6d) firmware version is the minimum tested version. For instructions on upgrading the CIMC firmware, refer to the Installing the Server chapter in the “Updating the BIOS and CIMC Firmware” section Cisco UCS C220 Server Installation and Service Guide.




Step 6 Click on the Launch KVM Console button at the top of the CIMC interface to launch the KVM console.

The KVM tab provides a view of the system diagnostics or command prompt execution. The Virtual Media tab provides the virtual CD/DVD setup for ISO installation.

Step 7 Prepare for the StadiumVision Mobile Streamer or StadiumVision Mobile Reporter ISO installation:

a. Click on Add Image tab under the KVM Console Virtual Media tab.

b. Navigate to the Streamer ISO file.

Note CIMC can experience slow performance. If slow performance occurs, clear the browser cache.



c. Click the check box for the Mapped option under Client View to select the ISO source.

d. Confirm that the Virtual CD/DVD has been added under the Virtual Media tab, Virtual CD/DVD.

e. Double click on Virtual CD/DVD, observe read bytes counter increasing (refreshes read bytes).

f. Close the KVM tab to start viewing the installation process.

Step 8 On the CIMC interface under Server Summary, click on Power Cycle Server to start the installation process.



Step 9 On the KVM Console/KVM terminal, confirm that the system is restarting and booting up from the Virtual CD/DVD.

Cisco UCS C200

To install on a Cisco UCS C200, begin installation with the following steps:

Step 1 Insert the installation disk into the DVD drive, boot from it, and follow the prompts. The server will boot from the installation disk.

Note Alternatively, the user is first requested to insert the DVD. Once inserted and the drive closed, the install proceeds automatically and does not display the Cisco logo.

The installation process begins, and the Cisco logo appears.

Step 2 Press F6 to continue booting.

Step 3 Select Cisco Virtual CD/DVD 1.20 in the dialog box.

Under the KVM Console/KVM tab, the Setup Agent menu is displayed.

For both Cisco UCS C220 and Cisco UCS C200, continue the installation with the following steps:

Step 4 Select Network Configuration from the menu.



Note Pay close attention, as the network configuration window displays for a brief period. If the window disappears, the installation needs to be restarted. If the installation seems to hang on a Cisco UCS C220, you may need to restart the installation by remapping the ISO image, and power cycling the Cisco UCS C220 server.

Step 5 Select Edit Devices and press the Enter key.

Step 6 Select eth0 and press the Enter key.

Step 7 Under Devernet Configuration, enter the network information. When done, select OK tab and press Enter.

Note The StadiumVision Mobile Streamer server IP address is a static IP address.



Step 8 Select save and press the Enter key.

Step 9 Select Edit DNS configuration and press Enter.



Step 10 Enter DNS information, when done, select OK tab, press Enter.

Step 11 Select the Save & Quit tab and press the Enter key.

Step 12 Select Exit tab and press the Enter key.

Cisco UCS C200 Servers

After this step, the Cisco StadiumVision Mobile software installs, the DVD is ejected, and the system reboots. This process takes about 30 minutes.

The installation should be completed. Validate the installation by logging into the StadiumVision Mobile Streamer or StadiumVision Mobile Reporter using the credentials listed in Table 5.

What To Do Next

• Set the time zone on the StadiumVision Mobile Streamer, page 14

• Start NTP on the StadiumVision Mobile Streamer, page 15

• Configure NTP on the StadiumVision Mobile Reporter, page 16

• Log into the StadiumVision Mobile Reporter TUI, page 17

• Start the Cassandra Service on the StadiumVision Mobile Reporter, page 17

• Set the Date and Time on the StadiumVision Mobile Reporter, page 17

• Set the User Time Zone on the StadiumVision Mobile Reporter, page 18

Set the time zone on the StadiumVision Mobile Streamer

Step 1 When the reboot is complete, ssh to the StadiumVision Mobile Streamer with the following credentials to set the time zone:

Table 5 Login Credentials

Device URL Usage User Name and Password

StadiumVision Mobile Reporter

http://svm:8080/reporter/dashboard.svm Client report login

'marketing' - marketing charts 'admin' - server administration chart

default password: cisco!123

StadiumVision Mobile Streamer

http://svm:8080/reporter/streamer.up Configuration GUI: Log in as ‘admin’ default password: cisco!123 Command line: manufac default password: cisco!123

Cisco Integrated Management Controller (CIMC) running on a Cisco UCS C220

http:// reporter or streamer ip address Configuration ‘admin’ - CIMC initial configuration default password: password



User: manufacPassword: cisco!123

Step 2 Change the password for manufac. Use the passwd command, which will then prompt for a new password.

Set the Time Zone

Step 3 First change to the time zone directory, then list the entry/directory options. If the desired time zone is listed within a directory, change to that directory.

cd /usr/share/zoneinfo

Step 4 Create a symbolic link to the desired time zone from /etc/localtime, eg, If an http proxy is required, modify /etc/profile with nano or other available editor

# sudo nano /etc/profile sudo ln –sf /usr/share/zoneinfo/Europe/Paris /etc/localtime

Step 5 Enter the SVM Streamer credentials if asked and then set the time zone entry in the file /etc/sysconfig/clock (eg, “Europe/Paris”). Confirm that the date is set correctly or modify if needed. View the date by entering:

# date

Set the server date and time

Step 6 If the date or time needs to be modified, enter the following command, using the appropriate date and time.

# sudo date –s “2 MAR 2012 18:00:00”

Step 7 If an http proxy is required, modify /etc/profile with nano or other available editor,

# sudo nano /etc/profile

Step 8 Enter SVM Streamer credentials if asked and insert the following entries:

Replace proxy-someproxy.com with the actual proxy to be used. export HTTP_PROXY=http://proxy-someproxy.com:8080 export http_proxy=proxy-someproxy.com:8080

Step 9 Enter the following command to restart the Streamer:

sudo /sbin/service svm-stream restart

Start NTP on the StadiumVision Mobile Streamer

In order to have accurate reports generated on the StadiumVision Mobile Reporter, the Network Time Protocol (NTP) service must be started on the StadiumVision Mobile Streamer immediately after installation. To start the NTP service, use the following procedure:

Step 1 Open ntp.conf in an editor: sudo vi /etc/ntp.conf



Step 2 Add 'server ip address' just before the line 'server 0.rhel.pool.ntp.org'

Step 3 Enable the NTP daemon: sudo /sbin/chkconfig --add ntpd

Step 4 Set the privileges for the NTP process with the following command: sudo /sbin/chkconfig --level 2345 ntpd on

Configure NTP on the StadiumVision Mobile Reporter

Step 1 When the reboot is complete, a login window appears. Login with the following credentials:

User: installerPassword: cisco!123

Step 2 The TUI (Text User Interface) will appear on the screen.

Step 3 Configure NTP from the System Settings/Date and Time Settings menu:

a. Set the system time.

b. Change the time zone, if applicable.

Note The default time zone is Eastern Standard Time (EST).

Note After setting the server time zone in the TUI. always restart the svmreporter service by using the Stop and Start options in the the StadiumVision Mobile Reporter Services menu.

c. Set the NTP server address.

Note It is critical that NTP be properly configured in order to provide accurate reports.



Log into the StadiumVision Mobile Reporter TUI

To access the StadiumVision Mobile Reporter TUI, you need either physical console access or an SSH client such as PUTTY. Log in from the console or over SSH with the following credentials, using the IP address of the StadiumVision Mobile Reporter: username = installer password = cisco!123

You will be prompted to change the password on your first successful login. You also have the option of changing the password via the TUI.

Start the Cassandra Service on the StadiumVision Mobile Reporter

There are two situations that require restarting of the cassandra service.

One case is during the network configuration part of the install process, when the hostname is configured. If the default “reporter” hostname is changed to something else other than the default, use the following procedure to update the hostname in the DNS config file, and restart the cassandra service.

Step 1 In the TUI, go to the System Settings/Network Settings/Edit DNS config. Change the hostname to ‘reporter’.

Step 2 In the TUI, go to Services Control/Chart and Config Database. Choose the Stop Service option, then the Start Service option.

The second case is that the hostname is changed via the StadiumVision Mobile Reporter TUI to something other than the default ‘reporter’ after installation. If this occurs, use the following procedure to update the hostname in both the hosts and the DNS config files, and restart the cassandra service.

Step 1 In the TUI, go to System Settings/Network Settings/Edit DNS config. Change the hostname to ‘reporter’

Step 2 In the TUI, go to System Settings/Network Settings/Edit hosts file. Change the hostname to ‘reporter’

Step 3 In the TUI, go to Services Control/Chart and Config Database. Choose the Stop Service option, then the Start Service option.

Set the Date and Time on the StadiumVision Mobile Reporter

To set the date on the StadiumVision Mobile Reporter, use the following procedure:

Step 1 Log into the TUI using the procedure in the “Log into the StadiumVision Mobile Reporter TUI” section.

Step 2 In the TUI, go to System Settings, Date and Time Settings, and Set System date.

Step 3 Enter the date using the following format: MMDDHHMIYYYY for Month Day Hour Minute Year



Note After setting the server timezone, always restart the svmreporter service by using the Stop and Start options in the the StadiumVision Mobile Reporter Services menu.

Set the User Time Zone on the StadiumVision Mobile Reporter

The StadiumVision Mobile Reporter has the default users marketing and admin, and a default time zone setting of Pacific Standard Time (PST). If the user browser or device is set to Pacific Standard Time (PST) and if the events are occurring in the EST time zone, the user can change the reports timestamp to the Eastern Standard Time (EST) time zone.

Each user time zone can be changed by using the following procedure:

Note Access to the StadiumVision Reporter CLI requires administrator access.

Step 1 SSH to the StadiumVision Mobile Reporter.

Step 2 Execute the./cassandra-cli shell command.

Step 3 Within the CLI console, execute the following commands:

a. use BDASchema;

b. set Users['marketing']['gmtoffset']='-8';

c. set Users['admin']['gmtoffset']='-8';

‘-8’ can be changed according to the desired time zone offset listed in Table 6.

Table 6 Time Zones and Offsets

Time Zone Offset Time Zone Abbreviation Time Zone Description

0 GMT Greenwich Mean Time

+1 ECT European Central Time

+2 EET European Eastern Time

+2 ART (Arabic) Egypt Standard Time

+3 EAT Eastern African Time

+3.5 MET Middle East Time

+4 NET Near East Time

+5 PLT Pakistan Lahore Time

+5.5 IST India Standard Time

+6 BST Bangladesh Standard Time

+7 VST Vietnam Standard Time

+8 CTT China Taiwan Time

+9 JST Japan Standard Time



Upgrading StadiumVision Mobile Reporter Using the Web Browser UI and TUIThe StadiumVision Mobile Reporter software can be upgraded using a combination of the web browser user interface, and the StadiumVision Mobile Reporter TUI. To upgrade the StadiumVision Mobile Reporter, use the following procedure:

Step 1 Navigate to the StadiumVision Mobile Reporter in a web browser, using the following address:

reporter ip address/cgi-bin/isoupload.cgi

Step 2 Click on the Choose File button, navigate to the ISO file, and click the Upload ISO button.

The ISO image is copied to the StadiumVision Mobile Reporter hard drive.

Step 3 Access the StadiumVision Mobile Reporter TUI, using the procedure in “Log into the StadiumVision Mobile Reporter TUI” section.

+9.5 ACT Central Australia Time

+10 AET Eastern Australia Time

+11 SST Solomon Standard Time

+12 NST New Zealand Standard Time

-11 MIT Midway Islands Time

-10 HST Hawaii Standard Time

-9 AST Alaska Standard Time

-8 PST Pacific Standard Time

-7 PNT Phoenix Standard Time

-7 MST Mountain Standard Time

-6 CST Central Standard Time

-5 EST Eastern Standard Time

-5 IET Indiana Eastern Time

-4 PRT Atlantic Standard Time

-3.5 CNT Canada Newfoundland Time

-3 AGT Argentina Standard Time

-3 BET Brazil Eastern Time

-1 CAT Central Africa Time

Time Zone Offset Time Zone Abbreviation Time Zone Description



Step 4 Navigate to the server upgrade option.

Step 5 Choose the desired software upgrade from the list and press enter.

The server begins the upgrade process.


Appendix A: CIMC Configuration and Firmware Upgrade Guidelines on the Cisco UCS C220 Server

First Published: March 22, 2013

This document provides guidelines for configuring the Cisco Integrated Management Controller (CIMC) interface and performing the initial configuration, and upgrading the CIMC/BIOS firmware on the Cisco UCS C220 servers for the Cisco StadiumVision Mobile Reporter and Cisco StadiumVision Mobile Streamer. (SV-M-STREAMER-K9, SV-M-REPORTER-K9.

Note Use the information in this appendix only as a guide to the tasks that you need to perform for CIMC configuration or upgrade, but follow the procedures in the referenced Cisco UCS documents.

This section includes the following topics:

• CIMC Initial Configuration, page 21 (required)

• CIMC Firmware Upgrade Guidelines, page 23 (as required)

CIMC Initial ConfigurationThis section includes the following topics:

• Prerequisites, page 21

• CIMC Initial Configuration Summary, page 22

PrerequisitesBe sure that the following requirements are met before you do the CIMC initial configuration:

• You have a monitor, keyboard, and mouse that you can connect to the server.

• You have the following information for configuring the internal Cisco Integrated Management Controller (CIMC) interface:

– You have an additional IP address for static configuration.

21Cisco StadiumVision Director Software Installation and Upgrade Guide

Appendix A: CIMC Configuration and Firmware Upgrade Guidelines on the Cisco UCS C220 ServerCIMC Initial Configuration

Tip This is a different IP address than the IP address that you configure for the eth0 network interface on the Cisco StadiumVision server.

– You have the VLAN ID if the server will be installed on a network VLAN.

– You are prepared to change the default CIMC login password.

• You have a laptop with access to the Cisco StadiumVision network.

• Your computer meets the minimum browser and Flash player requirements for the Cisco StadiumVision server, and also has Java 1.6 or later installed.

See the release notes for your Cisco StadiumVision product and release at:

http://www.cisco.com/en/US/products/ps11274/prod_release_notes_list.html

• You have a copy of or access to the following documents on Cisco.com:

– Cisco UCS C220 Server Installation and Service Guide

Familiarize yourself with the “Initial Server Setup” topic of the “Installing the Server” chapter.

– Cisco UCS C-Series Servers Integrated Management Controller GUI Configuration Guide, Release 1.4

(or the version that corresponds to your firmware release found at: http://www.cisco.com/en/US/products/ps10739/products_installation_and_configuration_guides_list.html.)

Familiarize yourself with the “Overview” chapter, and the “Managing the Server Boot Order” section of the “Managing the Server” chapter.

CIMC Initial Configuration SummaryThis section provides an overview of the basic tasks to be completed when performing the initial CIMC configuration in standalone mode for a Cisco StadiumVision server after you have unpacked and inspected it and prepared it for installation.

To perform the CIMC initial configuration, complete the following tasks:

Description

Configuring the CIMC Interface

Note The instructions for configuring the CIMC interface are found in the “Initial Server Setup” topic of the “Installing the Server”chapter in the Cisco UCS C220 Server Installation and Service Guide.

Step 1 During bootup, press F8 when prompted to open the BIOS CIMC Configuration Utility.

Step 2 Configure the CIMC interface with the following settings:

• DHCP—Disabled. You must change this option to enter a static IP address.

• CIMC IP—IPv4 address for your CIMC interface, with corresponding subnet mask.

• VLAN—Dependent on client network.

• Change the CIMC password. The default credential is admin and password.

Step 3 Press F10 to save your configuration and reboot the server.


http://www.cisco.com/en/US/docs/unified_computing/ucs/c/sw/gui/config/guide/1.4.1/b_Cisco_UCS_C-Series_GUI_Configuration_Guide_141.html


http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C220/install/install.html



http://www.cisco.com/en/US/products/ps10739/products_installation_and_configuration_guides_list.html

http://www.cisco.com/en/US/products/ps10739/products_installation_and_configuration_guides_list.html




Appendix A: CIMC Configuration and Firmware Upgrade Guidelines on the Cisco UCS C220 ServerCIMC Firmware Upgrade Guidelines

CIMC Firmware Upgrade GuidelinesThis section includes the following topics:

• Before You Begin, page 23

• Prerequisites, page 24

• CIMC/BIOS Firmware Upgrade Summary, page 24

Before You BeginSee the release notes for your Cisco StadiumVision product and release at:


• Find the minimum CIMC/BIOS versions tested for your Cisco StadiumVision Mobile (SV-M-STREAMER-K9, SV-M-REPORTER-K9) platform.

Configuring the NIC Properties

Note Information about configuring the NIC properties are found in the “Initial Server Setup” topic of the “Installing the Server”chapter in the Cisco UCS C220 Server Installation and Service Guide.

Step 4 From a laptop with access to the Cisco StadiumVision network, use a browser and type the IP address that you configured for the CIMC interface to connect to the CIMC console.

Step 5 From the Admin tab, click Network, and go to the Network Settings page.

In the NIC Properties box configure the following settings and save your changes:

• NIC mode—Dedicated

• NIC Redundancy—None

Configuring the Server Boot Order

Note The instructions for configuring the server boot order are found in the “Managing the Server Boot Order” section of the “Managing the Server” chapter of the Cisco UCS C-Series Servers Integrated Management Controller GUI Configuration Guide, Release 1.4

Step 6 From the Server tab, click BIOS.

Step 7 Configure the following boot order and save your changes:

• CDROM

• HDD

Description





http://www.cisco.com/en/US/docs/unified_computing/ucs/c/sw/gui/config/guide/1.4.1/b_Cisco_UCS_C-Series_GUI_Configuration_Guide_141_chapter_011.html





• From your Cisco StadiumVision platform, verify the CIMC and BIOS firmware versions in the CIMC console (Figure 1).

Figure 1 Firmware Verification From the CIMC Console

Note Unless there is another reason why an upgrade has been found to be needed, no upgrade should be needed if your server firmware is at the minimum tested version (or later) for the Cisco StadiumVision release that you are running.

PrerequisitesBe sure that the following requirements are met before you perform a CIMC/BIOS firmware upgrade:

• You have a copy of or access to the following documents on Cisco.com:

– Release Notes for Cisco UCS C-Series Software, Release 1.4(6)

(or the version that corresponds to your firmware release found at: http://www.cisco.com/en/US/products/ps10739/prod_release_notes_list.html)

– Cisco Host Upgrade Utility Release 1.4(6) Quick Start Guide

(or the version that corresponds to your firmware release found at: http://www.cisco.com/en/US/products/ps10493/products_user_guide_list.html)

Familiarize yourself with all of the requirements in these documents to perform your CIMC/BIOS firmware upgrade.

• You have access to Cisco.com to download the firmware ISO file.

CIMC/BIOS Firmware Upgrade Summary

Caution Be sure to follow the requirements in the release notes and the Host Upgrade Utility (HUU) guide for your firmware, including making sure that you upgrade both the CIMC and BIOS at the same time and from the HUU ISO file.


http://www.cisco.com/en/US/docs/unified_computing/ucs/release/notes/OL-27678-01.html


http://www.cisco.com/en/US/docs/unified_computing/ucs/c/sw/lomug/1.4.x/install/b_huu_1_4_6x.html

http://www.cisco.com/en/US/products/ps10493/products_user_guide_list.html


To perform the CIMC/BIOS firmware upgrade, complete the following tasks:

Description

Step 1 Using the release notes for the firmware version that you need to install, find the name of the ISO file that applies to the Cisco UCS C220 server for that firmware.

Note The release 1.4(x) firmware HUU ISO files are platform-specific.

Step 2 Follow the instructions in the Host Upgrade Utility guide:

Note The Cisco UCS C220 server does not have a CD/DVD drive.

• Go to Cisco.com and download the HUU ISO file.

• Follow the instructions to load the ISO that you downloaded and be sure that both the CIMC and BIOS firmware are upgraded together.


cisco stadiumvision mobile reporter and cisco ... › c › en › us › td › docs ›...

Documents