cit211 chapter 1 study guide
TRANSCRIPT
-
7/27/2019 CIT211 Chapter 1 Study Guide
1/11
Assessment Results
Item Feedback Report
CCNA Exploration: LAN Switching and Wireless (Version 4.0) -
ESwitching Chapter 1
Below is the feedback on items for which you did not receive full credit. Some interactive items may not display yourresponse.
Subscore:Domain Know ledge - Weighted Score
1
Which layer of the hierarchical network design model isrefered to as the high-speed backbone of theinternetwork, where high availability and redundancy are
critical?CorrectResponse
YourResponse
access layer
core layer
data-link layer
distribution layer
network layer
physical layer
This item references content from the following areas:CCNA Exploration: LAN Switching and Wireless
1.1.1 The Hierarchical Network Model
Which layer of the hierarchical designmodel provides a means of connectingdevices to the network and controlling
which devices are allowed tocommunicate on the network?
CorrectResponse
YourResponse
application
access
distribution
https://assessment.netacad.net/virtuoso/delivery/pub-doc/exam_result.shtml?THEME=rapport&STYLE=base&SLIX=bdN3CNsH8H4e0VPcp4Aands5D&ER_ID=122866871https://assessment.netacad.net/virtuoso/delivery/pub-doc/exam_result.shtml?THEME=rapport&STYLE=base&SLIX=bdN3CNsH8H4e0VPcp4Aands5D&ER_ID=122866871https://assessment.netacad.net/virtuoso/delivery/pub-doc/exam_result.shtml?THEME=rapport&STYLE=base&SLIX=bdN3CNsH8H4e0VPcp4Aands5D&ER_ID=122866871 -
7/27/2019 CIT211 Chapter 1 Study Guide
2/11
2network
core
This item references content from the followingareas:
CCNA Exploration: LAN Switching and Wireless
1.1.1 The Hierarchical Network Model
3 Which hierarchical design model layer controls the flow ofnetwork traffic using policies and delineates broadcastdomains by performing routing functions between virtualLANs (VLANs)?
CorrectResponse
YourResponse
application
access
distribution
network
core
This item references content from the following
areas:CCNA Exploration: LAN Switching and Wireless
1.1.1 The Hierarchical Network Model
5 Link aggregation should be implemented at which layer ofthe hierarchical network?
CorrectResponse
YourResponse
core only
distribution and core
access and distribution
access, distribution, and core
This item references content from the following areas:
-
7/27/2019 CIT211 Chapter 1 Study Guide
3/11
CCNA Exploration: LAN Switching and Wireless
1.2.3 Switch Features in a Hierarchical Network
6 What statement best describes a modular switch?
CorrectResponse
YourResponse
a slim-line chassis
allows interconnection of switches on redundant backplane
defined physical characteristics
flexible characteristics
This item references content from the followingareas:CCNA Exploration: LAN Switching and Wireless
1.2.2 Switch Features
7 Which feature supports higher throughput in switchednetworks by combining multiple switch ports?
CorrectResponse
YourResponse
convergence
redundant links
link aggregation
network diameter
This item references content from the following areas:CCNA Exploration: LAN Switching and Wireless
1.1.2 Principles of Hierarchical Network Design
8 Configuring communication between devices ondifferent VLANs requires the use of which layer of theOSI model?
Correct Your
-
7/27/2019 CIT211 Chapter 1 Study Guide
4/11
Response Response
Layer 1
Layer 3
Layer 4
Layer 5
This item references content from the followingareas:CCNA Exploration: LAN Switching and Wireless
1.2.2 Switch Features
9 Which two characteristics are associated with enterprise
level switches? (Choose two.)
CorrectResponse
YourResponse
low port density
high forwarding rate
high latency level
support link aggregation
predefined number of ports
This item references content from the followingareas:CCNA Exploration: LAN Switching and Wireless
1.2.2 Switch Features
10 Which two features are supported at all three levels of theCisco three-layer hierarchical model? (Choose two.)
CorrectResponse
YourResponse
Power over Ethernet
load balancing across redundant trunk links
redundant components
Quality of Service
-
7/27/2019 CIT211 Chapter 1 Study Guide
5/11
link aggregation
This item references content from the following areas:CCNA Exploration: LAN Switching and Wireless
1.2.3 Switch Features in a Hierarchical Network
11 A network administrator is selecting a switch that willoperate at the network core. Which three featuresshould the switch support for optimum networkperformance and reliability? (Choose three.)
CorrectResponse
YourResponse
port security
security policies
10 Gigabit Ethernet
quality of service (QoS)
hot-swappable hardware
Power over Ethernet (PoE)
This item references content from the following areas:
CCNA Exploration: LAN Switching and Wireless
1.2.3 Switch Features in a Hierarchical Network
14 For organizations that are implementing a voice over IPsolution, what functionality should be enabled at allthree layers of the hierarchical network?
CorrectResponse
YourResponse
Power over Ethernet
quality of service
switch port security
inter-VLAN routing
-
7/27/2019 CIT211 Chapter 1 Study Guide
6/11
This item references content from the followingareas:CCNA Exploration: LAN Switching and Wireless
1.2.3 Switch Features in a HierarchicalNetwork
15
Refer to the exhibit. Beginning with HR servers andworkstations, a network engineer is designing a newsecurity structure for the network. Which set of policiesadheres to the hierarchical network model designprinciples?
CorrectResponse
YourResponse
Implement Layer 3 switching on S1 to reduce the packet processingload on D1 and D2. Install all security processing on S1 to reduce networktraffic load.
Configure port security options on S1. Use Layer 3 access controlfeatures on D1 and D2 to limit access to the HR servers to just the HRsubnet.
Move all HR assets out of the data center and connect them to S1. UseLayer 3 security functions on S1 to deny all traffic into and out of S1.
-
7/27/2019 CIT211 Chapter 1 Study Guide
7/11
Perform all port access and Layer 3 security functions on C1.
This item references content from the followingareas:CCNA Exploration: LAN Switching and Wireless
1.1.1 The Hierarchical Network Model
16 A network technician is asked to examine an existingswitched network. Following this examination, thetechnician makes recommendations for adding newswitches where needed and replacing existing equipmentthat hampers performance. The technician is given a
budget and asked to proceed. Which two pieces ofinformation would be helpful in determining necessary portdensity for new switches? (Choose two.)
CorrectResponse
YourResponse
forwarding rate
traffic flow analysis
expected future growth
number of required core connections
number of hubs that are needed in the access layer to increaseperformance
This item references content from the following areas:CCNA Exploration: LAN Switching and Wireless
1.2.1 Considerations for Hierarchical Network Switches
17 A technician is attempting to explain Cisco StackWise
technology to a client that is setting up threestackable switches. Which explanation accuratelydescribes StackWise technology?
CorrectResponse
YourResponse
StackWise technology allows up to eight ports to be boundtogether to increase available bandwidth.
-
7/27/2019 CIT211 Chapter 1 Study Guide
8/11
StackWise technology allows the switch to deliver power to
end devices by using existing Ethernet cabling.
StackWise technology allows the switch capabilities andports to be expanded by the addition of line cards.
StackWise technology allows up to nine switches to beinterconnected via the use of a fully redundant backplane.
This item references content from the followingareas:CCNA Exploration: LAN Switching and Wireless
1.2.2 Switch Features
18 Which three features are commonly supported at the
distribution layer of the Cisco hierarchical network model?(Choose three.)
CorrectResponse
YourResponse
security policies
Power over Ethernet
switch port security
quality of service
Layer 3 functionality
end user access to network
This item references content from the following areas:CCNA Exploration: LAN Switching and Wireless
1.2.3 Switch Features in a Hierarchical Network
20
-
7/27/2019 CIT211 Chapter 1 Study Guide
9/11
Refer to the exhibit. What characteristic of hierarchicalnetwork designs is exhibited by having SW3 connectedto both SW1 and Sw2?
CorrectResponse
YourResponse
scalability
security
redundancy
maintainability
This item references content from the following areas:CCNA Exploration: LAN Switching and Wireless
1.1.1 The Hierarchical Network Model
Assessment Results
Item Feedback Report
CCNA Exploration: LAN Switching and Wireless (Version 4.0) -
ESwitching Chapter 1
https://assessment.netacad.net/virtuoso/delivery/pub-doc/exam_result.shtml?THEME=rapport&STYLE=base&SLIX=bdN3CNsH8H4e0VPcp4Aands5D&ER_ID=122866926https://assessment.netacad.net/virtuoso/delivery/pub-doc/exam_result.shtml?THEME=rapport&STYLE=base&SLIX=bdN3CNsH8H4e0VPcp4Aands5D&ER_ID=122866926https://assessment.netacad.net/virtuoso/delivery/pub-doc/exam_result.shtml?THEME=rapport&STYLE=base&SLIX=bdN3CNsH8H4e0VPcp4Aands5D&ER_ID=122866926 -
7/27/2019 CIT211 Chapter 1 Study Guide
10/11
Below is the feedback on items for which you did not receive full credit. Some interactive items may not display yourresponse.
Subscore:Domain Know ledge - Weighted Score
4
-
7/27/2019 CIT211 Chapter 1 Study Guide
11/11
This item references content from the following areas:CCNA Exploration: LAN Switching and Wireless
1.1.3 What is a Converged Network?
13
At which heirarchical layer are switches normally not required to process allports at wire speed?
CorrectResponse
YourResponse
core layer
distribution layer
access layer
entry layer
This item references content from the following areas:CCNA Exploration: LAN Switching and Wireless
1.2.2 Switch Features