clutch operated lexshade sbtta - · pdf filepocket, closure & wall clip options type d...
TRANSCRIPT
Please check all appropriate selections and attach room schedule with verified dimensions.
WIDTH2' 3' 4' 5' 6' 7' 8' 9' 10' 11' 12' 13'
HE
IGH
T
2'
3'
4'
5'
6'
7'
8'
9'
10'
11'
12'
13'* Sizes requiring large endcaps/brackets will vary according to fabric.
Safety Note: If shades are to be installed in areas accessible to young children, be certain to use cord tension device included with Bead Chain Clutch shades.Clutch-operated shades should not be installed near cribs or playpens.
Single Roller Clutch FlexShade XD OptionsFabric Series: _______________________________________
Color name / Number:________________________________
Openness Factor:___________________________________
Please see Draper's Shade Fabric Reference Guide for fabric colors and specifications.
Select Single Roller Hardware Endcaps Only Endcaps with Fascia Headbox
Ceiling / Wall (Surface Headbox) Pocket Style Type "D" Pocket with Tile Lip (White—not available with 3" roller) Custom Headbox
Wall Clip With Ceiling Tile Lip Without Ceiling Tile Lip
Closure Panel for Type "D" Pocket or Wall Clip 1½" (recommended) 3" 5" (For Wall Clip and Custom Headbox Only)
" L", "U" or "H" Channels for Light Gap Reduction 'L' Channel 'U' Channel 'H' Channel Channel Liners
Select Hardware Finish (does not apply to Type "D" or Pocket Headbox) Clear Anodized (standard) Black Ivory White Bronze Custom (Contact Draper)
Available Sizes* :
Select Number of Shades per Unit Single Roller (Standard) Dual Roller (Supplemental Fabric & Hardware Sheet Required)
Please Note: If you are specifying a Dual Roller FlexShade, please complete the options BELOW and attach the Dual Roller Clutch Operated Fabric and Hardware Planning Sheet.
Select Clutch Location As seen from INSIDE the room facing the window. Also indicate on room schedule.
Right (standard) Left
Select Clutch Color White (standard) Black
Optional Spring Assist
Spring Assist per manufacturer’s standards (as required based on fabric weight) Spring Assist on all units (Minimum Shade width 48")
Select Bead Chain Type Steel Chain
Stainless Steel (standard) Black Steel White Steel Polyester Chain
Black Bronze White Ivory Grey
Select Cord Tension Device 'P'-Clip Cord Tension Device (standard) Spring Loaded Cord Tension Device
Select Fabric Orientation
Regular Roll (from BACK of roller) Reverse Roll (from FRONT of roller)
Select Fabric Attachment Spline Attachment (standard) LSE Adhesive
Select Hem Bar Style Closed Pocket - 1" Elliptical Slat (standard) Open Pocket - 1" Elliptical Slat Small Flat Exposed Hem Bar Large Flat Exposed Hem Bar Round Exposed Hem Bar 13/16" Tube 5/8" Tube None
Clutch Operated FlexShade® XDWindow shade with heavy-duty clutch that is built for durability, ease of use and low maintenance.
PROJECT:
ARCHITECT:
CONTRACTOR:
SUPPLIER:
DATE: REVISED:
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.7999 © 2017 All Rights Reserved | FORM: FlexShadeXD_Sub17
SUBMITTAL TECHNICAL INFO
Pocket, Closure & Wall Clip OptionsType D pocket, white in color, features a 5" x 53/8" cross-section. A lip along lower edge supports lay-in ceiling. Pre-welded corners and pocket ends are available. Ends come with or without tile support lip (shown).
Typical pre-welded corner section (not to scale)
Type D Pocket5"
53/8"
7/8"1¾" 3" 3¼" 1½"
5"
53/8"
7/8"1¾" 3" 3¼" 1½"
Closure Options
3"
15/16"
5"
7/8"
1½"
15/16"
3"
15/16"
5"
7/8"
1½"
15/16"
3"
15/16"
5"
7/8"
1½"
15/16"
Wall Clip Options
1¾"
3/16"
Without Tile Lip
1¾"
3/16"
7/8"
With Tile Lip
SpecificationsEQUIPMENTXD CLUTCH OPERATOR: POM thermoplastic with welded 9 mm (.354") primary steel post with rotational bearing to ensure smooth and quiet operation. Overrunning design. Positive mechanical engagement of drive mechanism to tube. White (standard) or black color options. Stainless steel (standard) bead chain, or polyester control loop. Polyester chain in ivory, black or grey.ROLLERS: Extruded aluminum 1.56", 2", 2.36", 2.56" and 3.12" diameter roller tube as appropriate for size of shade.
COMPONENTSENDCAPS: 1018 steel stamping. 2 SIZES: 3¼" x 3¾" and 4½" x 4½". Complete with adapter roller bracket. Installs to face, ceiling, or jamb. Accepts box covers and fabric guide.ENDCAP COVERS: Plastic covers snap onto endcaps. Available in ivory, bronze, black or white to match fascia.HEM BAR: Closed Pocket Elliptical Slat: 1" aluminum elliptical slat inside of a 1 5/8" pocket with heat sealed ends. Open Pocket Elliptical Slat: 1" aluminum elliptical slat with plastic ends inside of a 15/8" pocket. Flat Exposed Hem Bar: Small: 7/8" x 5/16" and Large: 1½" x 5/16" aluminum rectangular hem bar with plastic end caps. Powder coated in black, bronze, ivory, white or clear anodized. Round Exposed Hem Bar: Small: 5/8" and Large: 13/16" aluminum with plastic end caps. Powder coated in black, bronze, ivory, white or clear anodized.FABRIC ATTACHMENT: Fabric attached to roller tube with spline fabric attachment method. Allows for removal of fabric panel without removal of roller assembly.
FASCIA: Optional L-shaped or radius cover of 6063-T5 extruded aluminum. Assembly snaps onto endcaps without exposed fasteners. Clear anodized finish (standard) or ivory, bronze, black or white powder coat. Fascia can also be wrapped in fabric. Radius fascia on small hardware only.HEADBOX: Standard consists of fascia, L-shaped back/top cover. Assembly snaps onto endcaps. Optional, for pocket installation, includes a U-shaped back/top/front cover with removable bottom closure panel. SMALL SIZE: 37/16" x 315/16". LARGE SIZE: 411/16" x 411/16". Some exposed fasteners required. Clear anodized (standard) finish or black, white, ivory or bronze powder coat finish.TYPE D POCKET: Fabricated of 6063-T5 aluminum alloy for perimeter installation. Finished white. 5" x 53/8" x .125" with tile support lip and removable bottom closure. Pre-welded corners and endcaps optionally availble. Larger 9½" x 53/8" x .125" version for mounting two XD mechanisms in the same pocket also available.DIMENSIONS: Shades to fit windows with maximum protection from light streaks. Finished length of shades no less than 6" greater than window height. "L" ANGLE (¾" x 1" x 12'3", 1" x 2¾" x 16' or cut to length) "U" CHANNEL (1" x 2½" x 16' or cut to length) and "H" CHANNEL (1" x 5" x 16' or cut to length): Accepts side edges of fabric, prevents light gaps. Interior of channel provides for use of flat head screws.
Patent information available at http://www.draperinc.com/legal/patents/ Downloadable 3-part specifications are available at www.draperinc.com.Please note: Dimensions of rollers, operators and hardware at manufacturer’s discretion.
Hardware SelectionsPlease Note: Brackets and endcaps have the only attachment points for mounting a motorized FlexShade. Optional fascia and headbox have a thickness of 1/16".
Fascia Only with Ceiling or Wall Mounting Endcaps
Wall Mounting Bracket Ceiling Mounting Bracket
Headbox Installation Options
Ceiling / Wall headbox consists of fascia, back/top cover and Ceiling / Wall mounting endcaps
Optional pocket style headbox consists of Draper’s extruded pocket with bottom closure panel and ceiling / wall mounting endcaps.
SMALL SIZE: 37/16" x 315/16" LARGE SIZE: 411/16" x 411/16"
Clutch Operated FlexShade® XD page 2 of 4
HEADBOX FASCIA W/ENDCAPS ENDCAPSSmall LargeA3
B3
A1
B1
C
D
Cloth Width = Overall Width - 15/8"
½" 9/16"
E
F1/16"
A2
B2
Small LargeA3
B3
A1
B1
C
D
Cloth Width = Overall Width - 15/8"
½" 9/16"
E
F1/16"
A2
B2
Small Large A3
B3
A1
B1
C
D
Cloth Width = Overall Width - 15/8"
½" 9/16"
E
F1/16"
A2
B2
A1 37/16" 411/16" A2 33/8" 45/8" A3 3¼" 4½"
B1 315/16" 411/16" B2 37/8" 45/8" B3 3¾" 4½"
C 13/16" 13/16" C 13/16" 13/16" C 13/16" 13/16"
D 15/16" 29/16" D 15/16" 29/16" D 115/16" 29/16"
E 13/16" 13/16" E 13/16" 13/16" E 13/16" 13/16"
F 13/16" 19/16" F 13/16" 19/16" F N/A N/A* For Wall Mounting Bracket, add 3/16" to A3 and B3.
Clutch Operated FlexShade XD Dimensions
A3
B3
A1
B1
C
D
Cloth Width = Overall Width - 15/8"
½" 9/16"
E
F1/16"
A2
B2
Overall Width includes plastic endcap covers)(Pair adds 1/8" to Overall Width)
A3
B3
A1
B1
C
D
Cloth Width = Overall Width - 15/8"
½" 9/16"
E
F1/16"
A2
B2
Top View of XD Clutch
Endcap CoverA3
B3
A1
B1
C
D
Cloth Width = Overall Width - 15/8"
½" 9/16"
E
F1/16"
A2
B2
Fascia A3
B3
A1
B1
C
D
Cloth Width = Overall Width - 15/8"
½" 9/16"
E
F1/16"
A2
B2
PLEASE NOTE: When measuring shade height, remember to include endcaps and fascia or headbox.
Small XD Wall Bracket
¾"
17/8"
11/8"
11/8"
2 ¾"
¼"
.20"7/8" 11/16"
11/16"2 3/16"
3 3/8"
3 ¼" 4 ½"
4 ½"
1 1/8"
2 9/16"
1 7/16"
9/16"
11/16"
3 5/8"
2"
1 1/8"
9/16" 3/8"
11/16"
2 9/16"
9/16"
Large XDWall Bracket
¾"
17/8"
11/8"
11/8"
2 ¾"
¼"
.20"7/8" 11/16"
11/16"2 3/16"
3 3/8"
3 ¼" 4 ½"
4 ½"
1 1/8"
2 9/16"
1 7/16"
9/16"
11/16"
3 5/8"
2"
1 1/8"
9/16" 3/8"
11/16"
2 9/16"
9/16"
Clutch Operated FlexShade XD Dimensions
Clutch Operated FlexShade® XD page 3 of 4
FlexShade XD Components
1
11
1
11
2
34
45
6
7
7
8
89
1012
13
14
9
13
1
1
2
3
4
4
5
5
6
6
8
8
7
7
9
1
2
3
1
4
4
5
5
6
6
8
87
7
9
1 PLASTIC ENDCAP COVER (STANDARD)2 IDLER ENDCAP (STANDARD)3 XD CLUTCH (STANDARD)4 WALL MOUNTING BRACKET (STANDARD)5 FIXED PIN IDLER6 SLAT BAR—15/8” SEALED HEM POCKET7 BEAD CHAIN8 BEAD CHAIN HOLD DOWN9 SPRING-LOADED CHAIN TENSION DEVICE
10 ALUMINUM FASCIA PANEL (STANDARD)11 PLASTIC ENDCAP COVER (LARGE)12 IDLER ENDCAP (LARGE)13 WALL MOUNTING BRACKET (LARGE)14 ALUMINUM FASCIA PANEL (LARGE)
Single Roller XD Components
Endcap Covers "U" Channel
“L” Angle
"L" AngleSpline Fabric Attachment "H" Angle
Hardware Selections
Clutch Operated FlexShade® XD page 4 of 4