NOKIA:CODES DESCRIPTIONS

*3370# Activate Enhanced Full Rate Codec (EFR) - Your phone uses the best sound quality but talk time is reduced my approx. 5%#3370# Deactivate Enhanced Full Rate Codec (EFR)*#4720# Activate Half Rate Codec - Your phone uses a lower quality sound but you should gain approx 30% more Talk Time*#4720# Deactivate Half Rate Codec*#0000# Displays your phones software version, 1st Line : Software Version, 2nd Line : Software Release Date, 3rd Line : Compression Type*#9999# Phones software version if *#0000# does not work*#06# For checking the International Mobile Equipment Identity (IMEI Number)#pw+1234567890+1# Provider Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)#pw+1234567890+2# Network Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)#pw+1234567890+3# Country Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)#pw+1234567890+4# SIM Card Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)*#147# (vodafone) this lets you know who called you last*#1471# Last call (Only vodofone)*#21# Allows you to check the number that "All Calls" are diverted to*#2640# Displays security code in use*#30# Lets you see the private number

*#43# Allows you to check the "Call Waiting" status of your phone.*#61# Allows you to check the number that "On No Reply" calls are diverted to*#62# Allows you to check the number that "Divert If Unreachable (no service)" calls are diverted to*#67# Allows you to check the number that "On Busy Calls" are diverted to*#67705646# Removes operator logo on 3310 & 3330*#73# Reset phone timers and game scores*#746025625# Displays the SIM Clock status, if your phone supports this power saving feature "SIM Clock Stop Allowed", it means you will get the best standby time possible*#7760# Manufactures code*#7780# Restore factory settings*#8110# Software version for the nokia 8110*#92702689# Displays - 1.Serial Number, 2.Date Made, 3.Purchase Date, 4.Date of last repair (0000 for no repairs), 5.Transfer User Data. To exit this mode you need to switch your phone off then on again*#94870345123456789# Deactivate the PWM-Mem**21*number# Turn on "All Calls" diverting to the phone number entered**61*number# Turn on "No Reply" diverting to the phone number entered**67*number# Turn on "On Busy" diverting to the phone number entered12345 This is the default security codepress and hold # Lets you switch between lines*#3283# or *#DATE# Date of Manufacture*#682371158412125# Software Version

__________________________________________________________________________

SIEMENS:MODELS CODES & DESCRIPTIONS*#0003*(secret code 8 digits)# All Siemens Phones: Service Provider UnlockSiemens S25/C25SP unlock *#0003*(secret code 8 digits)#Show IMEI code: * # 06 #Resets language to automatic selection : * # 0000 # then Green buttonPin OutData Cable schematicsPhone's connector pin-out:1- GND2- SB3- POWER4- NC5- TX6- RX7- CLOCK8- DATA9- GND MIC10- HF MIC11- AUDIO12- GND AUDIOSiemens S1/S3/S3 ComTo view the software date and else with S3 com, S4, S4Power, Sony cmdx 1000e press with SIM removed *#06# and left softkey.To view some other stuff with S4Power, Sony cmdx 1000e press with SIM removed *#06# and left softkey twice.To view the software date with S3 com, S4, S4Power, Sony cmdx 1000e press with SIM installed menu 98 and left softkey twice.ACTIVATE MONITOR MODESiemens S1/S3Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key), 5553756, Hang-Up Button (Red Handset key)

Siemens S3 COM/S4:

Menu, 9 (Phone Options), 7 (Phone Status - 8 on Some), Left Display Button (left MENU key), 7684666, Hang-Up Button (Red Handset key)Note: Now Monitor should appear at the bottom of the Network Options menu.MONITOR MODEPressing the right Display Button when in monitor mode will toggle into 1 and 2 modes

Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals.

Test Mode Indicators: (* = only available when call in progress )CH Channel Number

RX Signal Strength (dB)

N NCC (Colour Code)

B BCC (Colour Code)

CI Cell ID (in Hex)

C1+ How long before phone does forced hand over. (see RX and RXAM)

LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC

TXPWR Transmit Power (dB)

RXAM Receive signal strength cut-off point

TS* Time Slot Number

TA* Timing Advance. Distance from tower in Km X 2

PL* Power LevelPOWER tablePL: 5 6 7 8 9 10 11 12 13 14 15

dB: 33 31 29 27 25 23 21 19 17 15 13

Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02LF* C1 value with continuous transmission from tower

LS* C1 Value with discontinuous transmission from tower

QF* Bit Error Rate with continuous transmission from tower

QS* Bit Error Rate with discontinuous transmission from towerBER (bit error rate) tableQF/QS register: 0 1 2 3 4 5 6 7

% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6

Siemens S1/S3:Here's a trick to play Tetris, also known as Klotz on a Siemens S1.Turn the phone on. Enter PIN. Before the telephone has logged in to the your GSM net do the following steps.1: Choose F 9 (function settings)2: Choose send own number and push the right button for choose.3: Push 9USE 2 as < and 8 as > , rotate the klotz with 5 and drop with 4.

[I have just heard from one of the programmers of the phone that Tetris was in the phone during development, but it was removed before it was produced. Apparently someone has the patent on games in mobile phones and Siemens didn't want to pay the licensing fees. It was either in Menu F-9-9 or it's not there at all.]Siemens S3 Comfort

MONITOR MODE:The Siemens S3 Com series have a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone.TO ACTIVATE MONITOR MODE:Turn the phone on.Enter the PIN access code on press OK. (Only if is enabled).Press Menu. (Left top button).Press 9. (Phone Options).Press 8. (Phone Status) (May be button 7 in some phones).You may see your IMEI NumberLeft Display Button (Top left MENU key).7684666Hang-Up Button. (Red Handset key).

Note: Monitor should appear now at the bottom of the Network Options menu.MONITOR MODE

Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes

Siemens S4/S4 Power:In phonebook under "Own Phone No." enter +12022243121 (which is the number to the White House) and you'll get a greeting from the people who programmed the phone.MONITOR MODE

The Siemens S4 series have a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone.TO ACTIVATE MONITOR MODE:Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key), 7684666, Hang-Up Button (Red Handset key)Now "Monitor" should appear at the bottom of the Network Options menu.Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals.

Test Mode Indicators: (* = only available when call in progress )

--------------------CH Channel NumberRX Signal Strength (dB)N NCC (Color Code)B BCC (Color Code)CI Cell ID (in Hex)C1+ how long before phone does forced hand over. (see RX and RXAM)LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSCTXPWR Transmit Power (dB)RXAM Reeceive signal strength cut-off pointTS* Time Slot NumberTA* Timing Advance. Distance from tower in Km X 2PL* Power Level

Power Table

PL: 5 6 7 8 9 10 11 12 13 14 15dB: 33 31 29 27 25 23 21 19 17 15 13Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02

LF* C1 value with continuous transmission from towerLS* C1 Value with discontinuous transmission from towerQF* Bit Error Rate with continuous transmission from towerQS* Bit Error Rate with discontinuous transmission from tower

BER (bit error rate) tableQF/QS register: 0 1 2 3 4 5 6 7% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6

Siemens S6/S10:

In Phonebook, store as your own number: +12022243121Then you get the sun and two palms in the display, also a greeting message of the "MMI-team".It has been said that the phone number is the number of the Capitol building in Washington, DC (but not sure).

Siemens S15 Secret Menu's

Press * -> # -> 7 -> 4 -> 3 -> 6 -> 3 -> 6 -> 7 -> * -> 8 -> 3 ->7 -> 8 -> # ,press clear key to clear screen and return tostand-by modepress Menu, it will show additional menuMenu 3.3.4 Band selection,Menu 3.3.4.1 Automatic band selection,Menu 3.3.4.2 select GSM 900 only,Menu 3.3.4.3 select GSM 1800 only,Menu 10 Engineering,

Menu 10.1 MS info,

Menu 10.2 software detail,Menu 10.2.1 software version,Menu 10.2.2 EEPROM version,

Menu 10.3 Test/production detailsMenu 10.3.1 Hardware detaMenu 10.3.2 production detaMenu 10.3.3 Service detaMenu 10.3.4 Mechanical deta

Menu 10.1.1 MS info on, then on the screen show these, for example:

FCN RXL C1 C2642 011+11+91 -> PAGE 1

CID DSC CB11211 045 000 -> PAGE 2

BCC NCC TN000 002 00 -> PAGE 3

RXf RXs RQf RQs00 00 00 00 -> PAGE 4

ATa APa Hn Hf001 000 05 00 -> PAGE 5

DTU DTD HP CI+ ? - - -> PAGE 6

MM CC RRIdNS Nul Idl -> PAGE 7

__________________________________________________________________________PANASONIC:CODES DESCRIPTIONS*#06# For checking the International Mobile Equipment Identity (IMEI Number)

__________________________________________________________________________

MOTOROLA:CODES DESCRIPTIONS*#06# For checking the International Mobile Equipment Identity (IMEI Number)[][][] 119 [] 1 [] Activate Enhanced Full Rate Codec (EFR) - Your phone uses the best sound quality but talk time is reduced my approx. 5%[][][] 119 [] 0 [] Deactivate Enhanced Full Rate Codec (EFR)

__________________________________________________________________________

ERICSSON:CODES DESCRIPTIONS*#06# For checking the International Mobile Equipment Identity (IMEI Number)Shortcuts:Save a Missed Call into your phone directory Scroll to "Missed Call", press "Yes" to display the required number. Press any number (i.e. 0 to 9), then press "clear" once to clear that number, then press & hold "<" until you see "Store". Press "Yes"Hide your number when calling when you don't want the other party to know your number) After dialling the required number & before pressing "Yes", press ">" twice to choose "Hide Id?" & then

press "Yes". Also works for pre-programmed & last dialled numbers just press "No" & wait for the number to appear on the screen first then follow same procedureCheck you battery level when phone is off Press "No" quickly one time & wait for the battery meter to show up!Save a number into your phone memory (not SIM card) Follow normal procedures to store a phone number. When prompted to set a storage position, press "#" once & key in desired location, or press "#" twice for next available positionCall a phone number from SMS message You can call from within a SMS message if the phone number is written in it. Just scroll the message until the phone number appears on the display, then press "Yes" to call.

: NOKIA ::.

Nokia Universal Codes Code Description :These Nokia codes will work on most Nokia Mobile Phones

(1) *3370# Activate Enhanced Full Rate Codec (EFR) - Your phone uses the best sound quality but talk time is reduced my approx. 5%

(2) #3370# Deactivate Enhanced Full Rate Codec (EFR) OR *3370# ( Favourite )

(3) *#4720# Activate Half Rate Codec - Your phone uses a lower quality sound but you should gain approx 30% more Talk Time.

(4) *#4720# Deactivate Half Rate Codec.

(5) *#0000# Displays your phones software version, 1st Line : Software Version, 2nd Line : Software Release Date, 3rd Line : Compression Type. ( Favourite )

(6) *#9999# Phones software version if *#0000# does not work.

(7) *#06# For checking the International Mobile Equipment Identity (IMEI Number). ( Favourite )

(8) #pw+1234567890+1# Provider Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols).

(9) #pw+1234567890+2# Network Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols).

(10) #pw+1234567890+3# Country Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols).

(11) #pw+1234567890+4# SIM Card Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols).

(12) *#147# (vodafone) this lets you know who called you last.

(13) *#1471# Last call (Only vodofone).

(14) *#21# Allows you to check the number that "All Calls" are diverted to

(15) *#2640# Displays security code in use.

(16) *#30# Lets you see the private number.

(17) *#43# Allows you to check the "Call Waiting" status of your phone.

(18) *#61# Allows you to check the number that "On No Reply" calls are diverted to.

(19) *#62# Allows you to check the number that "Divert If Unreachable (no service)" calls are diverted to.

(20) *#67# Allows you to check the number that "On Busy Calls" are diverted to.

(21) *#67705646# Removes operator logo on 3310 & 3330.

(22) *#73# Reset phone timers and game scores.

(23) *#746025625# Displays the SIM Clock status, if your phone supports this power saving feature "SIM Clock Stop Allowed", it means you will get the best standby time possible.

(24) *#7760# Manufactures code.

(25) *#7780# Restore factory settings.

(26) *#8110# Software version for the nokia 8110.

(27) *#92702689# Displays - 1.Serial Number, 2.Date Made, 3.Purchase Date, 4.Date of last repair (0000 for no repairs), 5.Transfer User Data. To exit this mode you need to switch your phone off then on again. ( Favourite )

(28) *#94870345123456789# Deactivate the PWM-Mem.

(29) **21*number# Turn on "All Calls" diverting to the phone number entered.

(30) **61*number# Turn on "No Reply" diverting to the phone number entered.

(31) **67*number# Turn on "On Busy" diverting to the phone number entered.

(32) 12345 This is the default security code.

press and hold # Lets you switch between lines NOKIA 5110/5120/5130/5190 Go to Top IMEI number: * # 0 6 # Software version: * # 0 0 0 0 # Simlock info: * # 9 2 7 0 2 6 8 9 # Enhanced Full Rate: * 3 3 7 0 # [ # 3 3 7 0 # off] Half Rate: * 4 7 2 0 # Provider lock status: #pw+1234567890+1 Network lock status #pw+1234567890+2 Provider lock status: #pw+1234567890+3 SimCard lock status: #pw+1234567890+4 NOKIA 6110/6120/6130/6150/6190 IMEI number: * # 0 6 # Software version: * # 0 0 0 0 # Simlock info: * # 9 2 7 0 2 6 8 9 # Enhanced Full Rate: * 3 3 7 0 # [ # 3 3 7 0 # off] Half Rate: * 4 7 2 0 # NOKIA 3110 IMEI number: * # 0 6 # Software version: * # 0 0 0 0 # or * # 9 9 9 9 # or * # 3 1 1 0 # Simlock info: * # 9 2 7 0 2 6 8 9 # NOKIA 3330 *#06# This will show your warranty details *#92702689#

*3370# Basically increases the quality of calling sound, but decreases battery length. #3370# Deactivates the above *#0000# Shows your software version *#746025625#This shows if your phone will allow sim clock stoppage *4370# Half Rate Codec activation. It will automatically restart #4370# Half Rate Codec deactivation. It will automatically restart Restore Factory Settings To do this simply use this code *#7780# Manufacturer Info Date of Manufacturing *#3283# *3001#12345# (TDMA phones only) This will put your phone into programming mode, and you'll be presented with the programming menu.2) Select "NAM1" 3) Select "PSID/RSID" 4) Select "P/RSID 1" Note: Any of the P/RSIDs will work 5) Select "System Type" and set it to Private 6) Select "PSID/RSID" and set it to 1 7) Select "Connected System ID" Note: Enter your System ID for Cantel, which is 16401 or 16423. If you don't know yours, ask your local dealer for it. 8) Select "Alpha Tag"

9) Enter a new tag, then press OK 10) Select "Operator Code (SOC)" and set it to 2050 11) Select "Country Code" and set it to 302 for Canada, and 310 for the US. 12) Power down the phone and power it back on again ISDN CodeTo check the ISDN number on your Nokia use this code *#92772689# .:: Ericsson ::. Ericson T65 *#05# Fake Insert puk screen Press no to exit Ericsson T20

Ericsson T20

MENU tecnichal Info [type] >*<<*<*

Displays : 1] Info service 1] Info SW 2] Info hardware 3] SIMlock 4]setup

2] Service setup 1] Contrast

3]Service Test 1] Display

2]Leds 3]Keyboard 4] ringer 5] Vibration 6]Headset 7] Microphone 8]Clock 4] Names List

MENU info [Type] >*<<**< Network and Subnetwork : NCK and NSCK

Ericsson T28 >*<<*<* menu Tecnichal info SW vers. and name list >*<<**< menu Personal Info Network and Subnetwork : NCK and NSCK < and > are the right and left menu's keys Ericsson T18s/T10/A1018s >*<<*<* software CXC125065 Internal product code PRG 970715 1515 Software version and SW rev. <* CLR <><** >*<<*<*> Displays texts and messages in the phone It will be displayed " TEXT " then push YES < and > are the right and left menu's keys !!!><** Control /Enable SIM Lock!!! Ericsson R310

Technical Info : >*<<*<* Options : 1) service Info info Software Simlock Configuration

2) Service Test Display Led/Illumination Keyboard ringer Vibration Headset Microphone Clock

3)Text's name List Info personal : >*<<**<

SIM Locking ( 8 digits' code ) ( it could harm your phone ) 1) Network 2) Subnetwork 3) SP 4) Corporate

.:: Siemens ::. Siemens C25 IMEI number: * # 0 6 # Software version: put off sim card and enter: : * # 0 6 # and press LONG KEY

Bonus screen: in phone booke: + 1 2 0 2 2 2 4 3 1 2 1 .:: Bosch ::. IMEI Number: * # 0 6 # Dafault Language: * # 0 0 0 0 # Net Monitor: * # 3 2 6 2 2 5 5 * 8 3 7 8 # .::Alcatel ::. IMEI number: * # 0 6 # Software version: * # 0 6 # Net Monitor: 0 0 0 0 0 0 * .:: Samsung ::. Samsung SGH600/2100DB IMEI number: * # 0 6 # Software version: * # 9 9 9 9 # albo * # 0 8 3 7 # Net Monitor: * # 0 3 2 4 # Chaning LCD contrast: * # 0 5 2 3 # Memory info: * # 0 3 7 7 # albo * # 0 2 4 6 # Reset pamieci (SIMLOCK`a removing!!!): *2767*3855# Reset pamieci CUSTOM: *2767*2878# Battery state: * # 9 9 9 8 * 2 2 8 # Alarm beeper: *#9998*289# Vibra test: *#9998*842# .:: Dancall ::. IMEI number: * # 0 6 # Software version: * # 9 9 9 9 # .:: Philips ::. *#3333*# Displays the blocking list. *#7489*# Displays the security code. *#06# Displays the IMEI number. *#8377*# Displays the SW info. .:: Panasonic ::. Panasonic gd90 gd93

*#9999# SW - Type the code on switch on , during network seek -Vers. SW and production code Enable ringing and vibration contemporarily Enable vibration with # then increase volume with "tone menu " Panasonic gd70 *#9999# SW - Type the code on switch on , during network seek -Vers. SW and production code Enable ringing and vibration contemporarily Enable vibration with # then increase volume with "tone menu " .:: Acer ::. Acer V 750 *#400# Display Adc/ Set Cal-Value - *#402# Set LCD Contrast *#403# Display Errors Info *#300# Display Info Hw & Sw *#301# Menu Test *#302# Menu Acoustics *#303# (Settings saved) Set English language? *#307# Menu Engineering *#311# Reset Phone Code - [ Also reset Security Codes ! ] *#330# (Execute not success) [ unknown ] *#331# (Service deactivated) [ unknown ] *#332# (Service unavailable)[ unknown ] *#333# (Execute not success)[ unknown ] *#351# (Service unavailable) [ unknown ] *#360# (Invalid input)[ unknown ] *#361# (Invalid input) [ unknown ]

*#362# (Invalid input) [ unknown ] *#363# (Invalid input) [ unknown ] .:: Genie ::. Genie DB *#06# IMEI. *#2254*# Near Cell Mode.

For every received BTS will be displayed : Current channel and 2 channel levels

*#06# IMEI *#2558# time of network connection ( D/H/M ) *#2562# Fores reconnection to network !!!*#7489# Dispalys and modify phones' security code!!! !!!*#3377# SIM lock information !!! *#7378# SIM card Informations : supported phase name and tipe *#7693# Enable/disable "Sleep Mode" *#8463# State of "Sleep Mode" *#2255# Debug Call Mode enable/disable *#3333*# Displays the blocking list. *#7489*# Displays the security code *#06# Displays the IMEI number*#8377*# Displays the SW info.

.:: NEC ::. NEC db2000 *#2820# software vers. IMEI *#06# Reset *73738# (send?) SP Lock info:

* # 3210 # (send?) Network barring info : *#8140# (send?) ( it could harm your phone ) SIM lock it could harm your phone ) *#4960 # (send?) -Inquiry * 4960 * password * password # (send?) lock #4960* password # (send?) unlock [password] [8 digits] Net Lock *#7320# (send?) -Inquiry * 7320 * password * password # (send?) lock #7320* password # (send?) unlock [password] [ 8 digits] Net Lock 2: *#2220# (invio) - Inquiry * 2220 * password * password # (send?) lock #2220* password # (invio?)unlock [password] [8 digits] Unlock subnetwork *#1110# (send?) - inquiry * 1110 * password * password # (send?) lock #1110* password # (send?) unlock [password] [n� 8 cifre] ( it could harm your phone ) .:: Trium ::. Trium Geo/Geo @ - Astral - Cosmo -Aria

Enter the menu and type * A new menu will be displayed : Application : SW version and battery's voltage

Trium GalaxyPush * and type 5806: Production date and SW version

.:: Telit ::. Telit GM 810 MONITOR - technical menu - : type ++++ and push OK. Adiacent cells list : # and * Now if you push OK the phone displays battery ' s voltage and temperature .:: Sagem ::. Sagem MC959/940 Select commands' menu and push * Displays a new menu' : Appli : software vers. and battery's voltage Eprom Sim Lock Test LCD: display test , green/red and vibration Sagem MC920 Select commands' menu and push * Displays 5 new menus :

1 APPLI VERSION ( SW) BATTERY (voltage ) 2 PROM (IMEI) 3!!! SIM LOCK (10 digits code requested ) !!! 4- NETWORK (returns : OPTION NOT AVAILABLE) 5- TEST LCD SYMBOL 1 (LCD) SYMBOL 2 (test2 LCD)

BLACK (all icons and carachters displayed ) FOR PHOTO (welcome message and time ) VIBRATOR (vibration test )

.:: Sony ::. Sony CMD Z5/J5 Vers. SW : Without SIM , switch on phone and type l *#7353273# .:: Eprom ::.

!!! Sim Lock [10 digits code ] ( it could harm your phone ) NETWORK : OPTION NOT AVAILABLE Test LCD: display test of the green/red leds and vibration Push * and type 4329 :enables/disables network monitor 1 (the same of MT35) Push * and type 621342 :enables/disables network monitor 2 Push * and type 5807 : Serial Number Software Vers. Push * and type 936505: IMEI -- Software Vers. TPush * and type 547 : Test serial Data Cable DISPLAYS :"Testmode" Push * and type 362628: ISMI BLOCK (UNKNOWN) Push * and type 476989: NS BLOCK (UNKNOWN) Push * and type 482896:CP BLOCK (UNKNOWN) Push * and type 787090: ? BLOCK (UNKNOWN) Push * and type 787292 : block current network !!! Push * and type 967678: SP LOCK!!! Push * and type 850696:Warm Start ( ENABLE/DISABLE) Push * and type 3926 : Swicth off phone Push * and type 5806: Production date and SW version

.:: Motorola ::. Motorola V3688 IMEI *#06# Enhanced Full Rate Codec EFR Enable EFR : [][][] 119 [] 1 [] OK. disable EFR : [][][] 119 [] 0 [] OK .:: Tips and Tricks ::. Send an E-mail from your GSM From your telephone you can send an email to whichever E-mail customer of the Internet network.

The e-mail will be sent to the maximum of within an hour from the reception.

The sended message will contain in luminosity the telephone number of the sender.

In order for sending e-mail, send an SMS with this syntax (always separated by spaces):

EMA name@domain text-of-your-email

Example: in order to send an email to john@doe.com, do the following:

EMA john@doe.com text-of-your-email

if your phone cant print @ replace it with a !

EMA johon!doe.com text-of-your-email

And then send this message to the folloving number: +39 338 8641732

Free SMS Center numbers

From your telephone you can send SMS messages of 160 char. max. to another GSM phone

Your message will be sent through an SMS Center (usually the one that gave your provider)

You pay a little fee depending of your provider, BUT YOU WILL HAVE TO PAY something

In order for sending SMS without paying anything, you got to change your SMS Center number with these one

+491722270300 or +358405202999 or +352021100003

Codes (that they dont tell you in the manual) To check the IMEI (International Mobile Equipment Identity) type: *#06#

Information you get from the IMEI: XXXXXX XX XXXXXX X TAC FAC SNR SP

TAC = Type Approval Code (first 2 digits = country code).

FAC = Final Assembly Code (For Nokia phones FAC=10).

SNR = Serial Number.

SP = Spare (always SP=0).

To check the phone's software (firmware revision information) type: *#0000# ( or for some phones outher then Nokia 61XX you can try *#model nummber# ex. for 8110 *#8110#)

Information you can get from the phone's software version: V 3.14 28-11-97 NSE-3

1st line: Software version. 2nd line: The date of the software release. 3nd line: Phone type, .

Some versions and dates:

V 3.14 28/11/97

V4.33 11/03/98

V 4.73 22/04/98

V 5.24 14/9/98

Pin-Out Diagram for the 6110 1 - VIN CHARGER INPUT VOLTAGE 8.4V 0.8A 2 - CHRG CTRL CHARGER CONTROL PWM 32Khz

3 - XMIC MIC INPUT 60mV - 1V 4 - SGND SIGNAL GROUND 5 - XEAR EAR OUTPUT 80mV - 1V 6 - MBUS 9600 B/S 7 - FBUS_RX 9.6 - 230.4 KB/S 8 - FBUS_TX 9.6 - 230.4 KB/S 9 - L_GND CHARGER / LOGIC GND Revealing Headphone and Car-Kit Menus Think about this: If you do these tricks the new menus can not be erased after the procedure. But it's not dangerous or harmful for your phone

To enable the headset-function, you have to short-circuit the "3" and "4". After a short time there is "Headset" on the display Now, menu 3-6 is now enabled!

To enable the carkit-function you have to short-circuit the "4" and "5". After a short time, "Car" is shown on the display and the menu 3-7 is enabled!!

This Trick is for you how want to hear more then your supposed to ! If you short-circuit the left and the right contact with the middle contact ("3", "6" and "9") the Nokia Software hangs! The profile "Headset" will be activated. Before you do this, just active the "auto call receive" function in the headphone profile and set the ringing volume to "mute" Now you can use your phone for checking out what people are talking about in a room. Place the phone somewhere stratidic and call your phone! The phone receives the call

without ringing and you can listen to what people are talking about! .....gr8... Serial numbers on your 6110 For more info type: *#92702689# The first screen gives you the serial and IMEI number. Then there is the Date of Manufacture: ex. Made 1297 Then there is the Purchasing Date: ex. Purchasing Date 0298 Then there is the last Repair Date: ex. Repaired: 0000

Note: you must turn off the phone to exit after this test, because of the last function, "transfer user data" which doesn't work as "standard"....You can use this mode only to transfer all Calender, Profile and Callers Group Information to another phone (eg. if you are replacing phone or configuring phones for use within your company or when a particular phone doesn't works correctly )

Activating and deactivating EFR and HFR, on your 6110 *3370# to activate Enhanced Full Rate - Makes calls sound better, but decreases the battery life by about 5%.

#3370# to deactivate Enhanced Full Rate

*4720# to activate Half Rate Mode - Drops call quality, but increases battery life by about 30%.

#4720# to deactivate Half Rate Mode

Motorola

his phone follows similar methods as outlined for the 8000 series above.

Remove the battery and locate the three contacts at the bottom of the phone, the two outer contacts are raised and connect with the battery. The center contact is recessed, this is the Manual Test Mode connector.

Now look at the battery contacts, the two outer ones supply power to the phone, the center contact is an "extra" ground. This ground needs to be shorted to the test mode connector on the phone. The easiest way to do this is to put a small

piece of solder wick, wire, aluminum foil or any other conductive material into the recess on the phone. Having done this carefully replace the battery and turn on the power, if you have been successful the phone will wake up in test mode.

TEST MODE PROGRAMING:

Assuming you have completed one of the above steps correctly the phone will wake up in test mode when you turn the power on. When you first access test mode the phone's display will alternate between various status information that includes the received signal strength and channel number. The phone will operate normally in this mode. You can now access Service Mode by pressing the # key, the display will clear and a ' will appear. Use the following procedure to program the phone:

1. Enter 55# to access programing mode.2. The * key advances to the next step. (NOTE that test mode programing does NOT have step numbers, each time you press the * key the phone will display the next data entry).3. The CLR key will revert the display to the previously stored data.4. The # key aborts programing at any time.5. To complete programing you must scroll through ALL entries until a ' appears in the display.6. Note that some entries contain more digits than can be displayed by the phone, in this case only the last part of the data can be seen.

TEST MODE PROGRAMING DATA:

STEP# #OF DIGITS/RANGE DESCRIPTION

01 00000 - 32767 SYSTEM ID02 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 1 BELOW03 10 DIGITS MIN (AREA CODE & TEL#)04 2 DIGITS STATION CLASS MARK05 2 DIGITS ACCESS OVERLOAD CLASS06 2 DIGITS GROUP ID (10 IN USA)07 6 DIGITS SECURITY CODE08 3 DIGITS LOCK CODE09 3 DIGITS SERVICE LEVEL (LEAVE AT 004)10 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 2 BELOW11 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 3 BELOW12 0333 OR 0334 INITIAL PAGING CHANNEL13 0333 "A" SYSTEM IPCH14 0334 "B" SYSTEM IPCH15 3 DIGIT NUMBER PAGING CHANNEL (021 IN USA)16 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 4 BELOW

Steps 01 through 06 and 12 will repeat for NAM 2 if the second phone number bit has been enabled in step 11.

NOTES:

Take care with Motorola's use of "0" and "1". Some options use "0" to enable, some use "1".

These are eight digit binary fields used to select the following options:

1. (step 02 above, suggested entry is: 11101001 for "A" system, 10101001 for "B" sys)

Digit 1: Local use mark, 0 or 1.Digit 2: Preferred system, 0 or 1.Digit 3: End to end (DTMF) dialing, 1 to enable.Digit 4: Not used, enter 0.Digit 5: Repertory (speed) dialing, 1 to enable.Digit 6: Auxiliary (horn) alert, 1 to enable.Digit 7: Hands free (VSP) auto mute, 1 to enable (mutes outgoing hands free audio until the MUTE key is pressed).Digit 8: Min mark, 0 or 1.

2. (step 10 above, suggested entry is: 00000100)

Digits 1 - 4: Not used in USA, enter 0.Digit 5: Single system scan, 1 to enable (scan A or B system only, determined by bit 2 of step 02. Set to "0" to allow user the option).Digit 6: Super speed dial, 1 to enable (pressing N, or NN SND will dial the number stored in memory location NN).Digit 7: User selectable service level, 0 to enable (allows user to set long distance/memory access dialing restrictions).

Digit 8: Lock function, 0 to enable (allows user to lock/un-lock the phone, if this is set to 1 the phone can not be locked).

3. (step 11 above, suggested entry is: 00000000)

Digit 1: Handset programing, 0 to enable (allows access to programing mode without having to enter test mode).Digit 2: Second phone number (not all phones), 1 to enable.Digit 3: Call timer access, 0 to enable.Digit 4: Auto system busy redial, 0 to enable.Digit 5: Speaker disable, 1 to enable (use with select VSP units only, do not use with 2000 series mobiles).Digit 6: IMTS/Cellular, 1 to enable (rarely used).Digit 7: User selectable system registration, 0 to enable.Digit 8: Dual antennae (diversity), 1 to enable.

4. (step 16 above, suggested entry is: 0011010 for portable and 0011011for mobile units)

Digit 1: Not used, 0 only.Digit 2: Not used, 0 onlyDigit 3: Continuous DTMF, 1 to enable (software version 8735 and later)Digit 4: 8 hour time-out, 0 to enable (software version 8735 and later)Digit 5: Not used, 0 only.Digit 6: Failed page indicator, 0 to enable (phone beeps when an incoming call is detected but signal conditions prevent completion of the call).Digit 7: Portable scan, 0 for portable, 1 for mobile units.

C-SCAN OPTION:

Newer Motorola phones are equipped with a feature called C-Scan, this is an option along with the standard A/B system selections. C-Scan allows the phone to be programed with up to five inhibited system ID's per NAM. This is designed to prevent the phone from roaming onto specified non-home systems and therefore reduce "accidental" roaming fees.

1. C-Scan can only be programed from test mode, power phone up with the relevant test mode contact grounded (see above).2. Press # to access test mode.3. Press 18#, the phone will display "0 40000".4. Enter the first inhibited system ID and press *.Continue to enter additional system ID's if required. After the 5th entry the phone will display "N2". Press * to continue and add system ID's for NAM 2 as required.5. If an incorrect entry is made (outside the range of 00000-32767) the display will not advance, press CLR and re-enter. Use a setting of 40000 for any un-needed locations.6. When the last entry has been made press * to store and press # to exit, turn off power.

LOCK/UNLOCK PROCEDURES:

Phones with "LOCK" buttons: Press lock for at least 1/2 a second.

Phones with a "FCN" button: Press FCN 5, note that 5 has the letter's "J,K, and L" for lock.

Phones with no FCN or LOCK button: Press Control 5, control is the black volume button on the side of the handset.

SYSTEM SELECT PROCEDURES:

Phones with a RCL button: Press RCL *, then * to select, STO to store.

Phones with no RCL button: Press Control * then * to select, # to store.

Options are: CSCAn: Preferred/Non preferred with system lockout.Std A/b, or Std b/A: Preferred/Non preferred.SCAn Ab, or SCAn bA: Non preferred/PreferredSCAn A: "A" ONLYSCAn b: "B" ONLYHOME: Home only

(these are typical options, some phone's vary. C-Scan only available on newer models and does not appear unless programed, see above

GENERAL NOTES:

HANDSETS: Most Motorola handsets are interchangeable, when a handset is used with a transceiver other than the one

it was designed for the display will show "LOANER". Some features and buttons may not work, for instance if the original handset did not have a RCL or STO button, and the replacement does, you will have to use the control * or control # sequence to access memory and A/B system select procedures.

MOTOROLA TEST MODE COMMANDS:

01# RESTART (POWER OFF THEN ON)

02# STATUS DISPLAY, ALTERNATES BETWEEN:

ABC DEF where:

ABC = Channel numberDEF = Received sensitivity for that channel

and: A B C D E F G where:

A = SAT frequency (0=5970, 1=6000, 2=6030, 3=no channel lock)B = Carrier (0=off, 1=on)C = Signalling tone (0=off, 1=on)D = Power level (0 through 7)E = Channel mode (0=voice channel, 1=control channel)F = Receive audio mute (0=unmuted, 1=muted)G = Transmit audio mute (0=unmuted, 1=muted)

Press * to hold display and # to end.

03# Reset call timers

04# Initialize Tranceiver to following settings:

Carrier = OFFReceive Audio = MUTEDTransmit Audio = MUTEDSignaling Tone = OFFCall Timer RESET and peroiodic resetting ENABLEDSAT = OFFDTMF & Audio Tones = OFFAudio Path = To SPEAKER

05# Turn Carrier ON06# Turn Carrier OFF07# Mute RECEIVE audio08# Unmute RECEIVE audio09# Mute TRANSMIT audio10# Unmute TRANSMIT audio11ABC# Load Synthesizer with ABC, where ABC=the channel number in decimal12A# Set RF power level to A, where A=1 to 713# Power down phone14# Transmit signaling tone15# Stop transmit of signaling tone16# Transmit a five word reverse voice channel message, all words will be: "FF00AA55CC33"17# Transmit a two word reverse voice channel message, both words will be: "FF00AA55CC33"

18# Display contents of NAM one address at a time, press * to advance, press # to exit. (Two digit number to the left is the ADDRESS, to the right is the DATA)19# Display software version20# Receive control channel messages counting correctable and uncorrectable errors. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display two three digit numbers. The first number is the number of correctable errors and the second is uncorredtable errors.21# Receive voice channel messages counting correctable and uncorrectable errors. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display two three digit numbers. The first number is the number of correctable errors and the second is uncorredtable errors.22# Receive control channel messages counting word sync sequences. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display the number of word sync sequences in the display.23# Receive voice channel messages counting word sync sequences. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display the number of word sync sequences in the display.24# Turn SAT transmission ON25# SAT OFF

27# Transmit continuous control channel data, all words are: "FF00AA55CC33". When the command starts the number of the command will be displayed in the upper right hand corner of the display. Press # to terminate the test.28# Activate high tone (1150 Hz +/- 55 Hz)29# Deactivate high tone30# Activate low tone (770 Hz +/- 40 Hz)31# Deactivate low tone32# Initialize all non-volatile memory to zeros. Resets unit and makes it look "new".33A# Activate DTMF tone where A = DTMF digit 0 thru 934# Deactivate DTMF35A# Send audio path to A where A = 0 for handsfree, 1 for speaker, 2 for alert, 3 for Handset36ABC# Activate channel scan, ABC is scan speed in milliseconds. Tunes from channel 1 to 666. Press * to pause scan and display RSSI, if scan speed is 300 milliseconds or greater the RSSI is displayed with each channel, if scan is less than 300 milliseconds the RSSI is only displayed when you press *37# not used38# Display serial number in hex (ESN). Displayes the byte number in the upper right side of the display and the data to the left, press * to step through the bytes, press # to exit.39# Receive one control channel word, when the word is received it will be displayed in hex. Command terminates when the word has been received or when # is pressed.40# Receive one voice channel word, when the word is received it will be displayed in hex. Command terminates when the word has been received or when # is pressed.

41# (F19CTA models only) Enables the diversity antenna option on mobiles so equipped.42# Disable diversity.43# Disable diversity and force the mobile to use the TRANSMIT antenna.44# Disable diversity and force the mobile to use the RECEIVE antenna.45# Display the RSSI reading taken on the current channel.46# Display the cumulative call timer.47A# Set audio level to A where A = 0 lowest, A = 6 highest, or A = 7 muted.48# Turn sidetone on49# Sidetone off50# Maintenance data is transmitted and test results displayed: PASS =Received data is correct, FAIL1 = No data received within 2 seconds, FAIL2 = Received data is incorrect.51# Maintenance data is transmitted and looped back and test results displayed: PASS = Looped back data is correct, FAIL1 = No data looped back within 2 seconds, FAIL2 = Looped back data is incorrect.52A# Set phase adjustment. A decimal number thet corresponds to phase shift compensation in 4.5 degree increments. Compensation added to the inherant phase shift of the tranceiver to acheive a total phase shift of 0 (zero) degrees. Do not enter any value other than from the following list:

# entered, Degree of shift0 0 59 121.5 86 243.01 4.5 60 126.0 87 247.5

2 9.0 61 130.5 112 252.03 13.5 62 135.0 113 256.54 18.0 63 139.5 114 261.05 22.5 40 144.0 115 265.56 27.0 41 148.5 116 270.07 31.5 42 153.0 117 274.516 36.0 43 157.5 118 279.017 40.5 44 162.0 119 283.518 45.0 45 166.5 120 288.019 49.5 46 171.0 121 292.520 54.0 47 175.5 122 297.021 58.5 64 180.0 123 301.522 63.0 65 184.5 124 306.023 67.5 66 189.0 125 310.548 72.0 67 193.5 126 315.049 76.5 68 198.0 127 319.550 81.0 69 202.5 104 324.051 85.5 70 207.0 105 328.552 90.0 71 211.5 106 333.053 94.5 80 216.0 107 337.554 99.0 81 220.5 108 342.055 103.5 82 225.0 109 346.556 108.0 83 229.5 110 351.057 112.5 84 234.0 111 355.558 117.0 85 238.5

53# Enable scrambler option, if equipped.54# Disable scrambler option, if equipped.55# Test Mode programming.58# Compandor on. Audio compressor and expandor on.59# Compandor off. Audio compressor and expandor off.

61# Serial number transfer, not all models.62# Turn on audio ringer path.63# Turn off audio ringer path.70# Abbreviated field transmitter audio deviation command for tranceivers with FCC ID: ABZ89FT5668.71# Abbreviated field power adjustment command for tranceivers with FCC ID: ABZ89FT5668.72# Field audio phasing command.73# Field power adjustment command.

ig33 - chat to your buddies on MSN on the Internet on your mobile phone, and you can make long distance calls at cheap calling card rates, and send SMS anywhere for one low rate.

Code:www.mig33.com---------------------------

It's not just about messaging.

It's about having conversation with whoever you like ... wherever you like .. and in the language you like (whatever language your phone and your friend's phone supports).

You can engage in private conversations with your friends on your buddy list.

You can also meet new people in our thousands of chatrooms, or create chatrooms for you and your friends.

---------------------------

Think you're connected?

mig33 takes you to a whole new level.

Without changing applications, you can chat in group chatrooms, private chat, send SMS and even connect to MSN Messenger and Yahoo Messenger - as fast as you can type on your phone.

Our Tabbed user interface makes it easy and convenient to chat with as many people at the same time, and as you want to.

---------------------------

Cheap Phone

Calls & SMS

And when you actually want to talk to the person you're chatting with, mig33 gives you cheap voice calls and SMS.

Tired of paying high rates for international calls? Cheap calling cards inconvenient on your mobile phone? Do you find it costs a lot, just to make the call and punch in all those serial numbers?

With mig33, it's really easy to launch a cheap international call. Just select your buddy, and select 'call buddy' to launch a call. Our global VOIP network (with presence in the United Kingdom, Hong Kong, Australia and the USA) is ever expanding so as to give you the best service and the best rates.

It's more than just cheap calls, we also give you cheap SMS (AUD$0.10) to over 200 networks around the world.

You can control your costs as well. Making calls back to a mobile phone is expensive. You can 'throw' the call to a landline near you and save even more. How's that for convenience?

---------------------------

Spread the Word!

Share mig33 with all your friends!

From mig33, you can send mig33 to your friends. From within mig33, simply select 'Invite friend' and they will receive an SMS invitation to install mig33 on their phone. Once installed, you'll get an extra AUD$1.00 of credit to make phone calls and send SMS.

You can also share your credits with other users. Simply open your account balance in mig33, and select 'Transfer credit' to push credits to other users. Now you and your friends can recharge your account once and share your credits around.

You can also make money with mig33, with our distribution opportunities. You can sell a Prepaid Calling Card service through us.

We will also be widening our distribution channels to include Western Union money transfer, support for mobile content providers, and prepaid voucher numbers shortly.

---------------------------

RequirementsJAVA midp1.0 mobile phone with GPRS or WAP enabled

Compatible Devices

Motorola A1000 Motorola A920 Motorola A925 Nokia 3230 Nokia 3600 Nokia 3620 Nokia 3650 Nokia 3660 Nokia 6260 Nokia 6600 Nokia 6620 Nokia 6630 Nokia 6670 Nokia 6680 Nokia 6681 Nokia 6682 Nokia 7610 Nokia 7650 Nokia 7710 Nokia 9200 Series Communicator Nokia 9210 Communicator Nokia 9290 Communicator Nokia 9300 Nokia 9500 Nokia N-Gage Nokia N70 Nokia N90 Nokia N91 (S60 3rd Edition) Nokia Series 60 Sony Ericsson P800

Sony Ericsson P900 Sony Ericsson P910

GSM TRAINER

The GSM module (Global System for Mobile communication) F 35 is a mobile station for transmission of voice and data calls as well as short messages (SMS- Short Message Service) in GSM Network.

To control the GSM module there is an advanced set of AT commands according to GSM ETSI (European Telecommunications Standards Institute) 07.07 and 07.05 implemented.

GENERAL INTRODUCTION: Your modem utilizes the GSM standard for cellular technology. GSM is a newer radio frequency (RF) technology than the FM technology that has been used for radio communications for decades. The GSM standard has been established for use in the European community and elsewhere. Your modem is actually a low power radio transmitter and receiver. It sends out and receives radio frequency energy. When you use your modem, the cellular system handling your calls controls both the radio frequency and the power level of your cellular modem.

Trainer includes:

- EVAL-Board- Adapter PCB for A2D or F35 called adapter- Adapter PCB for CM2C or CM35 called CM adapter- Wall mount power adapter- 9-pin serial cable (pin to pin direct, male to female)- GSM antenna (900/1800) and cable (30cm) with coaxial plug- coaxial adapter MMCX - FME- coaxial adapter MCCard - FME- Head-set with RJ-45 plug- Set of connectors (see appendix for details)- 2 pieces 40-pin stacking connector (plug and socket)- 2 pieces coaxial antenna plug (plug and socket)- 2 pieces 15-pin cable connector (plug and socket)- 2 pieces external SIM card reader- 3 pieces short circuit bridges- 4 pieces mounting clamps

- 4 pieces dowel- CD- “A2D-Testsoftware”

Following experiments can be performed with this trainer:

Experiments are divided into five different parts:-

1) GSM THEORY & STANDARDSUnderstanding of GSM technology, its network, GSM capability & data services.

2) COMPONENT STUDYUnderstanding the concept of RF component & different parts which is related to RF environment like GSM 900/1800 dual band antenna,RF module & various connectors & evaluation board etc.

3) RF ENVIRONMENTUnderstanding RF environment & study of GSM network by actually connecting to the GSM environment by any service provider SIM like Airtel, Idea, RPG etc.

4) COMMAND LEVEL STUDYReal Time study of GSM 07.05 & 07.07 commands in various categories:-

a) Command concerning modem & simcard hardware.b) Network registration commands.c) Call control commandsd) Call setting commands.e) Call information commands.f) Phone Book commands.g) Serial link control commands.h) Message setting commands.i) Storing / restoring commands.j) Error message handling & survey

& many more……………..

5) MEASUREMENT OF VARIOUS SIGNALS Signals can be measured on 40 pin connector (Test points) like SIM reset, SIM clock, SIM data, RTC etc.

Applications:

Advanced communication lab Broadband communication lab

Cellular mobile communication lab Wireless communication lab

Included accessories:

Theory manual Operating manual FAQ & application manual GSM glossary & used abbreviations Complete evaluation kit Power point presentation on GSM.