commissioner dept. of employment and … · morth specification no. 201 ha 0.150 42114.00 6317.10 2...

Tender Document Issued To:

Name of the Tenderer : ______________________________________________________

Address : ______________________________________________________

______________________________________________________

______________________________________________________

Signature of the Official Issuing the Tender Document with Desingation and Date

COMMISSIONER

DEPT. OF EMPLOYMENT AND TRAINING

BENGALURU

Bangalore - 560 001

Construction of Govt. ITIs at Humnabad in Bidar and at Chincholi in

Kalburgi District, Karnataka for Dept. of Employment and Training -

Package - II

Open Tender Notice No. RITES/BLR/OT/09/2015 dated 17.04.2015

FINANCIAL BID

RITES Ltd.,

E.Mail : [email protected]

(A Govt. of India Enterprise)

Site Office

3 A, Bharat Apartments, 44/1,

Fairfield Layout, Race Course Road

TENDER

Phone: 080 - 22257118 / 22280268

Fax: 080 - 22266557

Schedule WORKS COST (`̀̀̀)

I Construction of Govt. ITI Colleges at Humnabad in

Bidar District

II Construction of Govt. ITI Colleges at Chicholi in

Kalburgi District

TOTAL PROJECT COST

TOTAL IN WORDS

Construction of Govt. ITIs at Humnabad in Bidar and Chincholi in Kalburgi District,

Karnataka for Dept. of Employment and Training - Package - II

SUMMARY OF COST

RITES Ltd.,

For and on behalf of DET 1 Signature of the Bidder

SN DESCRIPTION AMOUNT

Civil Works

1 Part A - KPWD SR Items `

2 Part B - CPWD SR Items `

3 Part C - Market rate Items `

4 Part D - Panchayat Raj SR Items `

Electrical Works


2 Part B - Market rate Items `

TOTAL - Schedule I `

TOTAL

(in Words) - Rupees

Construction of Govt. ITI at Humnabad in Bidar District

ABSTRACT - Schedule I

RITES Ltd.,


Description Unit Qty

P. No l No

Part- A - KPWD SR Items

1 132 18.13 KSRRB M200-10.1. Clearing and grubbing road land including

uprooting rank vegetation, grass, bushes, shrubs, saplings and

trees girth up to 300 mm, removaL of stumps of trees cut earlier

and disposal of unserviceable materials and stacking of

serviceable material to be used or auctioned, including removal

and disposal of top organic soil not exceeding 150 mm in

thickness complete as per specifications. I. By Manual Means:

A. In area of light jungle. MORTH Specification No. 201

Ha 0.150 42114.00 6317.10

2 5 2.4 KSRB 2-2.2: Earth work excavation for foundation of buildings,

water supply, sanitary lines and electrical conduits either in pits

or in trenches 1.5m and above in width in Hard soil not

exceeding 1.5m in depth, including dressing the bottom and

sides of pits or trenches, stacking the excavated soil clear from

edges of excavation with lead upto 50 m after breaking of clods

complete as per specifications. Specification No. KBS

2.1(b)/2.3.5

Cum 235.990 244.00 57581.56

3 5 2.6 KSRB 2-2.4: Excavation 1.5m and above in width in soft rock

without blasting for foundation of buildings, water supply,

sanitary lines and electrical conduits either in pits or in trenches

not exceeding 1.5m in depth, stacking the excavated stuff from

edges of excavation with lead upto 50m including cost of labour

and HOM of euipment complete as per specifications.

Specification. No KBS 2.1.d / 2.9.4 / 2.18 / 2.19

Cum 235.990 758.00 178880.42

4 6 2.10 KSRB 2.3 : Filling available excavated earth ( excluding rock )

in sides of foundations upto plinth in layers not exceeding 20

cms. in depth, compacting each deposited layer by ramming

after watering with lead upto 50 m. and lift upto 1.5 m. including

cost of all labour complete as per specifications. specification.

No. KBS 2.9 Cum 663.080 109.00 72275.72

5 9 3.2 KSRB -3.2: Providing and injecting chemical emulsion for Pre-

constructional Anti-Termite Treatment, creating continuous

chemical barrier under and around the column pits,walls

,trenches,basement excavation,top surface of the plinth filling,

junction of wall and floor, along the external perimeter of

building, expansion joints, over the top surface of consolidated

earth on which apron is to be laid, surrounding of pipes and

conduits, with chloropyriphos emulsifiable concentrates of

20%concentration, including cost of chemical, diluting in water

to one percent concentration, labour, HOM of equipments,

complete as per specifications.(Plinth area of the building at

ground floor only shall be measured ) Specification No. KBS

3.2.6 / 3.2.7

Sqm 637.000 100.00 63700.00

6 12 4.3 KSRB 4-1.3: Providing and laying in position plain cement

concrete of mix M7.5 with OPC cement @ 180kgs, with 40mm

and down size graded granite metal coarse aggregates @

0.85cum and fine aggregates @ 0.57cum machine mixed,

concrete laid in layers not exceeding 15cms, thick, well

compacted, in foundation and plinth including cost of all

materials, labour, HOM of machinery, curing complete as per

specifications. specification No KBS 4.1,4.2

Cum 90.300 4329.00 390908.70


Rate AmountSN Gulbarga SR -

2014-15

RITES Ltd.,



P. No l No


2014-15


concrete of M 10 with OPC cement @220 kgs with 20mm and

down size graded granite metal coarse aggregates @ 0.84 cum

and fine aggregates @ 0.56 cum, machine mixed, concrete

laid in layers not exceeding 15 cms, thick, well compacted, in

foundation and plinth and cills, inclduing cost of all materials,

labour, HOM of machinery, curing complete as per

specifications. Specification No KBS 4.1,4.2

Ground Floor Cum 13.780 4776.00 65813.28

First Floor Cum 8.150 4826.00 39331.90

8 13 4.12 KSRB 4-2.7: Providing and laying in position reinforced cement

concrete of design mix M 25 with OPC cement @ 340 kgs with

20mm and down size graded granite metal coarse aggregates

@ 0.70 cum and fine aggregates @ 0.47 cum, with

superplastisiser at 3.0 lts. conforming to IS103-1999 reaffirmed -

2008, machine mixed, concrete laid in layers not exceeding 15

cms, thick, vibrated for all works in foundation plinth and ground

floor level for roof slabs, staircase, lintels, retaining wals, return

wall, wall (any thickness ) including attached plasters, columns,

piers, abutments, pillers, posts, struts, buttresses, string or

lacing courses, parapets, coping, bed blocks, anchour blocks,

plain windows cills, fillets etc., inclduing cost of all materials,

labour, HOM of machinery, curing complete as per specification

No KBS 4.1,4.6

Ground floor Cum 296.810 5805.00 1722982.05

First floor Cum 1.730 5855.00 10129.15

9 15 4.28 KSRB 4-6.1 : Providing and removing centering, shuttering,

strutting, propping etc., and removal of form work for

foundations, footings, bases of columns for mass concrete

including cost of all materials, labour complete as per

specifications. Specification No. KBS 4.6.2Sqm 176.600 211.00 37262.60

10 15 4.29.2 KSRB 4-6.2: Providing and removing centering, shuttering,

strutting, propping etc., and removal of form work for flat

surface such as suspended floors, roofs, landings, balconies

and likes, thickness up to 200mm including cost of all materials,

labour complete as per specifications. for 0-5m Height ,

Specification No. KBS 4.6.2Sqm 637.00 530.00 337610.00

11 15 4.32 KSRB 4-6.5: Providing and removing centering, shuttering,

strutting, propping etc., for columns, pillars, piers, abutments,

post and struts, square /rectangular / polygon in plan including

cost of all materials, labour complete as per specification.

Specification No. KBS 4.6.2

Ground floor Sqm 419.31 346.00 145081.26

First floor Sqm 72.32 351.00 25384.32


strutting, propping etc., an removal of form work for sides and

soffits of beams, beam haunchings, cantilever girders,

bressumers and lintels not exceeding 1m in depth including cost

of all materials, labour complete as per specifications.

Specification No. KBS 4.6.2 Sqm 648.300 250.00 162075.00


strutting, propping etc., for chajjas, corbels etc., including edges


specification. Specification No.KBS 4.6.2 Sqm 31.68 259.00 8205.12

RITES Ltd.,



P. No l No


2014-15



stairs(excluding landing) except spiral staircase including cost

of all materials, labour complete as per specification.


15 17 4.46 KSRB 4.9.2 : Providing T.M.T steel reinforcement for R.C.C

work including straightening, cutting, bending, hooking, placing

in position, lapping and / or welding wherever required, tying

with binding wire and anchoring to the adjoining members

wherever necessary complete as per design (laps, hooks and

wastage shall not be measured and paid) cost of materials,

labour, HOM of machinery complete as per specifications.


4.46.2 For TMT bars Fe 500 Ton 25.380 69243.00 1757387.34

16 23 5.3 KSRB-5.1-3 : Providing and cosntructing Granite/ trap/ basalt

rubble stone masornry in foundation cement mortar 1:6,

(Uncoursed) bond stones at two m. apart in each course

including cost of materials, labour, curing complete as per

specifications. KBS 5.1.12 Cum 43.050 2766.00 119076.30

17 23 5.6 KSRB-5.2.3: Providing and constructing Granite/ trap/ basalt

size stone masornry in foundation cement mortar 1:6, stone

hammerd dressed in courses not less than 20 cms high, bond

stones at two m.apart in each course including cost of

materials, labour, curing complete as per specifications. KBS

5.1.13 Cum 36.900 4326.00 159629.40

18 25 5.27 KSRB 5-14: Providing and constructing precast concrete solid

blocks with compressive strength not less than 35Kg/Sqm with

cement mortar 1:4 masonry (quoin, jamb, closer blocks) with

solid concrete blocks of size 40X20X20cms conforming to 1.S:

2185/1965 in superstructure including cost of materials, labour

charges, scaffolding, curing complete as per specifications.

Ground Floor Sqm 765.160 880.00 673340.80

First floor Sqm 179.700 910.00 163527.00

19 25 5.28 KSRB 5-15: Providing and constructing non load bearing wall

with cement concrete solid blocks with compressive strength

not less than 35Kg/Sqm with cement mortar 1:4 masonry (jamb,

closer blocks) with solid concrete blocks of size 40X10X20cms

(l X b X h)conforming to 1.S: 2185/1965 in superstructure

including cost of materials, labour charges, scaffolding, curing

complete as per specifications.

Sqm 88.920 634.00 56375.28

RITES Ltd.,



P. No l No


2014-15

20 37 7.17 KSRB 7.17 : Providing, fabricating, assembling and fixing in

position aluminium doors using following aluminium mat finish

or glossy finish, outer frame plain section 101.6x44.45mm

thickness 3.18mm, section weight 2.404 kg/m, door shutters

vertical section 44.62x44.45mm thickness 3.18mm, section

weight 1.505kg/m, top section 47.62x44.45mm thickness

3.00mm, section weight 1.426kg/m bottom section 114.3x44.45

thickness 3.18mm, section weight 2.646kg/m, door central

section 49.91x44.45mm thickness 3.00mm, section weight

1.495 kg/m glazing clips 19x17.3x11mm thickness 0.9mm

section weight 0.124kg/m; aluminium sections cut to length joint

metred cornersgrinded, the shutters pivoted opening

arrangement with heavy duty aluminium alloy automatic door

closures floor mounted, providing and fixing standard approved

accessories, such as aluminium handle for full width or length,

tower bolts, lock, pivots: P.V.C. or rubber gasket with 5.5m.

thick plain glass for top and bottom panel; aluminium sections

treated for removal of any rust and prevention of further rust

formation,

and coated with greasy materials for non-adherance of mortars

or any other sticky materials; the assembled frame fitted with

the corner angles, strips and fitted with screws, rawl plugs or

teakwood gutties to R.C.C. columns or masonry on sides.

beams and flooring in bottom. including cutting, chistling and

making good with cement mortar to match the surface; all the

frames throughly cleaned free from rust, scale, or dirt including

cost of materials, fixtures, labour and HOM of machinery


7.17.2 using aluminium section powdered coated to a minimum of 60-

70 microns with exterior durable pure polyester grade powder of

approved quality. Sqm 2.880 6080.00 17510.40

21 39 7.24 "Providing and fixing cold rolled prepainted steel windows of IS

standards, made out of 0.6mm thick deep drawing quality

galvanised on both sides 120gms/sq.mtr. Primer coat upto 5

microns with thermosetting epoxy resin and finish painted with a

polyester based paint 20 microns thick. The size of profiles is

approximately 46 x 52mm for external frames, 46x46mm

section for shutters, 46x70mm section for centre

mullion/transom and 18x31mm section is for fixing glasses. The

section should be cut to length joint mitred and assembling by

means of corner brackets made out of cold rolled cold annealed

strips of 1.2mm thick duly galvanised and fixed with nickle

plated self taping screws.The shutters are provided with

approved quality of fixtures like handles made out of zamac

alloy die cast and powder coated, receiver made out of glass

filled nylone and hinges made out of

CRCA powder coated. 4mm thick glass should be fixed with

EPDM gaskets. Guard bars fabricated out of 10mm square

bright bars shall be fixed horizontally at 125mm C/C by rivetting

to the external frame. The above frames are fixed to the

concrete / masonry walls by means of self expanding screws.â€

with 4mm float glass with gaurd bars

39 7.24.1(c ) 4mm float glass with gaurd bars Sqm 75.960 4000.00 303840.00

RITES Ltd.,



P. No l No


2014-15

22 42 7.35 Providing and fixing M.S hand railing for Balcony/staircase etc.,

with 50mm dia M.S hollow pipe of 14 gauge, welded to

20mmX20mm M.S. square rod placed vertically, spaced at

100mm at regular inetrvals of 600mm. These veryical rods

laterally tied to 3 horizontal rods spaced at equal interval. These

assembly is fixed to concrete by using expansion bolts and

welding the same to reinforcement bars and making good the

surface. ALl the joints and sections should be cut to length,

welded and grinded wherever necessary etc., complete. The

work includes cost of all materials, labour charges for all items

of work, hire charges for welding, cutting and grinding

equipment, and electricity charges etc., complete as per

specification and drawing

Sqm 10.000 2615.00 26150.00

23 46 8.3 KSRB 8.3-1 : Providing and laying to required line and slope

roofing with corrugated asbestos cement sheet 6mm. thick fixed

with galvanised iron J or L hooks, bolts and nuts 8mm. dia C.I

plain and bitumen washers over the existing purlins, rafters and

trusses including cost of materials, labour, complete as per

specifications. Specification No. KBS 8.5

Sqm 35.000 394.00 13790.00

24 59 9.93 Providing and fixing factory made single leaft rigid GRP

Sandwich composite door shutter of 32mm thick, laminated with

two GRP skins with wood grain finish, fabricated using U.V-

stabilized Isopathic Gelcoat and on layer of 45 gsm E-class

Chopped strand Mat (CSM), impregnated with orthopthalic

polyster resin. The thickness of the skins shall not be less than

1.5mm. Expanded Polystyrene (EPS) structural foam panel of

29mm thickness and a density of 20Kg/m3 shall be used as

core mterial. Wooden reinforcements made of seasoned

Salwood block of cross section not less than 28mmX32mm and

also necessary salwood reinforcements for fixing the metal

fittings such as tower bolts, aldrops, handles etc shall be

provided. A structural adhesive compatible with EPS foam shall

be used for bonding the core material, the salwood

reinforcement and the skins.

The material and process for manufacturing the door shutters

shall confirm to RV/TIFAC composites Design Centre standards

and specifications and the door shutters tested in confirmation

to IS 4020-1994. The finish of shutter will be plain colour

White/Ivory/Beige/Light Grey or any other colour using high

quality pigments. Excluding cost of fixtures and inclusive of

supply of shutters to respective work spot.

Sqm 9.450 3200.00 30240.00

25 60 9.96 Providing and fixing 65mm X 125mm GRP Door frame

fabricated using E-Glass Chopped Strand Mat (CSM) U.V -

sablized Isopathlic Gelcoat and Isopthalic resin. The thickness

of the GRP Skin shall not be less than 2.0mm. The door frame

consists of four segments, which are provided with plug-in-

socket arrangement in-situ in the mould. The segments are

plugged in and are joined together by means of screws. The

GRP frame shall be provided with wooden reinforcement on 6

locations for high screw holding capacity for fixing metalling

hold fast and shall be consolidated by filling with medium

density foam/plaster of paris with fibre reinforcement. Six

numbers of 260mmX25mmX5mm size S shaped M.S. flat hold

fast shall be provided with the frame.

m 25.500 565.00 14407.50

RITES Ltd.,



P. No l No


2014-15

26 67 11.1 KSRB 12-1.1 : Providing and laying in position to required level

or slope 100mm internal diameter salt glazed stoneware pipes

grade A and jointing with stiff mixture of cement mortar in

proportion of 1:1, testing of pipes and joints, including cost of

materials, labour charges complete as per specifications.

Specification No. KBS 12.2.5/12.7Rmt 50.000 219.00 10950.00

27 67 11.2 KSRB 12-1.2: Providing and laying in position to required level






28 68 11.37 KSRB 12-5.1: Construction brick masonry circular type man

hole 0.91m internal diameter at bottom 0.91m and 0.56mt dia

at top with table moulded non modular bricks of class

designation 50 in cement mortar 1:4, inside cement plastered

12mm thick with cement motar 1:3, finished with floating coat of

neat cement , foundation concrete of 1:3:6 mix using 40mm and

down size granite metal and making neccessary channel in

cement concrete 1:2:4 with 20mm and down size granite metal

finished with floating coat of of neat cement wit SFRC cover and

frame (heavy duty, HD-20 grade desination) 560mm internal

diameter confirming to IS 12592, total weight cover and frame

to be not less than 182 Kg fixed in cement concrete 1:2:4 20mm

and down size broken granite metal providing and removing

centering shuttering including cost of material , labour charges

HOM of machineries complete as per specification NO KBS12.4

Nos 1.000 11795.00 11795.00

29 70 11.50 KSRB 12-8.1 : Constructing brick masonry inspection chamber

455x610mm, and 450mm depth. (clear inside dimension) for

single pipeline, using table moulded non-modular bricks of class

designation 50 in cement mortar 1:5, C.I cover with frame (light

duty) 455x610mm internal dimensions. total weight of cover with

frame to be not less than 38 kg (weight of cover 23kg and

weight of frame 15 kg) R.C.C. top slab with cement concrete

1:2:4 mix 20mm and downsize granite metal, foundation

concrete 1:5:10 with 40mm and downsize granite metal inside

plastering 12mm thick with cement mortar 1:3, finish smooth

with a floating coat of cement on walls and bed concrete

complete as per standard design including cost of materials,

labour charges, curing complete as per specifications.

Nos 2.000 6106.00 12212.00

30 71 11.52 KSRB 12-8.2: Construction brick masonry inspection chamber

500x700mm and 450mm depth (clear inside dimension) for

pipeline with one or two inlets, using table moulded non modular

bricks of class designation 50 in cement mortar 1:5 , CI cover

with frame ( light duty) 455x610mm internal dimension, total

weight of cover with frame to be not less than 38Kg (weight of

cover 23kg and weight of frame 15kg) RCC top slab with

cement concrete 1:2:4 mix 20mm and downsize granite metal,

foundation concrete 1:5:10 with 40mm and downsize granite

metal inside plastering 12mm thick with cement mortar 1:3

finished smooth with floating coat of cement on walls and bed

concrete complete as per standard design including cost of

materials, labour charges, curing complete as per

specifications.

Nos 2.000 6927.00 13854.00

RITES Ltd.,



P. No l No


2014-15

31 74 12.1 KSRB 11.1 : Providing and fixing white vitreous chine clay water

closet Indian type (Sqatting pan) of size 580mm with foot rests,

100mm S or P tarp, 10 litres low level, PVC flushing cistren (all

are approved make) with fittings, CI /MS brackets, 32mm dia

flush pipe fittings and clamps, overflow arrangements with

special and 25mm mosquito proof coupling of approved design,

painting of fittings and brackets, cutting and making good the

wall and floor wherever required, including cost of materials,

labour complete as per specifications. KBS 11.

Nos 4.000 3408.00 13632.00

32 74 12.5 KSRB 11.5 Providing and fixing white vitreous china clay water

closet European type (pedestrial type, P trap) with black solid

plastic sheet and lead cover, CP brass hinges, rubber buffer 10

litres low level PVC flushing chintrens with fittings CI / MS

bracket 50 mm dia meter flush bend with fitting and clapms over

flow arrangements with special and 25 mm mosquitto proof

coupling of approved design and painting of fitting and brackets

cutting and making good the wall & floor required including cost

of material etc. complete as per specification no. 11.

Nos 4.000 4942.00 19768.00

33 75 12.11 KSRB.11.8.1: Providing and fixing white vitreousss china clay

wall corner type lipt front Urinal basin of size 340x410x265mm

with 5 litres PVC automatic flushing cistern, CI/MS brackets

standar flush pipe and cp brass speraders with brass union and

GI clamps complete painting of fitting and brackets cutting and

making the good wall and floor wherever required inlcuding cost

material labour complete as per specification No. KSB 11.

Nos 1.000 2733.00 2733.00

35 78 12.28 KSRB 11-11.6 : Providing and fixing white vitreous china clay,

angle back wash basin size 600x480mm with a single 15mm

CP brass pillar tap with CI / MS brackets, 32mm CP brass

waste of standard pattern, painting of fittings and brackets,

cutting and making good the wall and floor wherever required,

including cost of materials, labour complete as per

specifications. No. KBS 11 Nos 4.000 2962.00 11848.00

36 79 12.34 KSRB 11-13.2 : Providing and fixing Laboratoru sink of white

glazed fire clay of size 600x450x200mm with M.S / C.I brackets

, C.P brass chain with rubber plug, 32mm C.P brass waste, tap

with union, brass stop cock complete, painting of fittings and

brackets, cutting and making good the wall and floor wherever

required, including cost of materials, labour complete as per

specifications. KBS11

Nos 4.000 3229.00 12916.00

37 79 12.39 KSBR 11-15.1: Providing and fixing 600x450mm bevellead

edge mirror of superior glass with 6mm hard board backing and

fixed to wooden cleat with CP Screws, washers, including cost

of materials, labour complete as per specification.

Nos 4.000 1229.00 4916.00

38 85 12.113.1 Providing and fixing C.I. Nahani trap of approved make

confirming to ISI specification and construction of cistern in M-

15 as per direction (Rate is inclusive of cost of materials and

fixtures and conveyance of materials to work spot) 10x7.5cms

Nos 18.000 220.00 3960.00

39 88 13.20 KSRB 13-4.1: Making connection GI distribution branch with GI

main of 25 to 40mm nominal bore including cutting and

threading the pipes, providing and fixing Tee, nuts, labour for all

item of works, testing and HOM of equipments complete as per

specifications. Specification No. KBS 13.10

Nos 15.000 330.00 4950.00

RITES Ltd.,



P. No l No


2014-15

40 88 13.23 KSRB13-6.1-1 : Providing and fixing in position brass bib cock

of approved quality 15mm nominal bore including cost of all

materials, labour and HOM of equipments with all leads


13.2.2/13.3 Nos 12.000 218.00 2616.00

41 88 13.26 KSRB 13-6.2-2: Providing and fixing in position brass stop cock

of approved quality 20mm nominal bore inlcuding cost of all

materials labour and HOM equipment with all leads complete as

per specification. KBS 13.2.2 /13.3

Nos 10.000 160.00 1600.00

42 87 13.6 KSRB 13-1.6: Providing and fixing to wall, ceiling and floor

galvanised/mild steel tube 50mm dia nominal bore with fittings

(medium grade weight 5.24kg/mtr) B class including cost of all

materials, labour charges, HOM of equipments and testing


13.2.14/13.8 m 44.000 837.00 36828.00

43 90 13.70 KSRB 13-8.5: Providing and fixing to wall, ceiling and floor, low

density polyethylene pipes 6.00 kgf/sqcm working pressure

50mm outside diameter with special flange, compression type

fittings, wall clips, making good the wall, ceiling and floor,

including cost of all materials, labour charges, HOM of

equipments and testing complete as per specifications.

Specification No. KBS 13.2.15.1 /13.9

75 mm dia m 75.000 297.00 22275.00

110 mm dia m 75.000 421.00 31575.00

44 90 13.73.4 KSRB 13-8.9 : Providing and fixing to wall, ceiling and floor high

density polyethylene pipes 6.00 kgf / sq.cm working pressure

110 mm outside diameter with special flange, compression type

fittings, wall clips, making good the wall, ceiling and floor

including cost of all materials, labour charges, HOM of

equipments and testing complete as per specifications

.Specification No. KBS 13.2.15.2 / 13.9

- do -110 mm dia ( Rain water pipe) m 90.000 566.00 50940.00

45 91 13.78 KSRB 13-11.1: Providing and placing on terrace, polyethylene

water storage tanks with man hole lid and suitable locking

arrangements, making holes of suitable diameter for inlet, outlet

and over flow pipes, including cost of all materials, labour,

transport charges, HOM of equipments and testing complete as

per specifications (for 1000 litre capacity). Specification No.

KBS 13.22

Nos 1.000 8332.00 8332.00

46 91 13.79 Providing and fixing gun metal wheel valve conforming to IS

specification of approved make as per directions including all

ead and lifts etc., complete

13.79.2 For 20mm dia Each 3.000 365.00 1095.00

13.79.3 For 25mm dia Each 3.000 505.00 1515.00

13.79.4 For 32mm dia Each 3.000 740.00 2220.00

13.79.5 For 40mm dia Each 3.000 940.00 2820.00

13.79.6 For 50mm dia Each 3.000 1440.00 4320.00

47 87 13.1 KSRB13-1.1 : Providing and fixing to wall, ceiling and floor

galvanised / mild steel tube 15mm dia nominal bore with fittings

(medium grade weight 1.27 kg/mtr) B class including cost of all



13.2.14/13.8

15 mm dia m 50.000 179.00 8950.00

87 13.2 20 mm dia m 50.000 218.00 10900.00

87 13.5 40 mm dia m 30.000 425.00 12750.00

87 13.6 50 mm dia m 200.000 497.00 99400.00

RITES Ltd.,



P. No l No


2014-15

48 102 14.36 KSRB 14.14-5: Providing Ceramic tiles of size 30x30cms of

approved make, shade and size for flooring, treads of steps and

landings laid on a bed of 12mm thick, cement mortar 1:3 mix

flush pointing with white cement using colour pigment, including

cost of materials, labour, curing. complete as per specifications.

103 14.36.2 ……do……. For ceramic tiles of size 30 x 30 cms Sqm 36.800 1006.00 37020.80

49 103 14.41 KSRB 14-17.2: Providing skirling, dado, rises of steps with

colour glazed tiles 6mm thick on lOmm thick cement plaster 1:3

and Jointed with white cement slurry over rough plaster surface

(exculding cost of rough plastered surface which should be

measured and paid separetly) using glazed tiles of approved

make and size including cost of labour ,materials complete as

per specifications. Specification No KBS14.16,14.17.

103 14.41.1 …..do…….. Colour glazed tiles 15cm x 15cm x 6mm thick

Sqm 31.870 1400.00 44618.00

50 106 14.61 Providing and fixing 20mm thick gang saw water cut sadarhalli

grey granite in CM 1:4 proportion, cut to required shape, pattern

with paper joints, finished with cement mortar using white

cement and colour pigments to match the colour of slab making

through jointing with sealant, grooves in joints including cost of

curing.

14.61.1 minimum width of 900 mm Sqm 240.950 1895.00 456600.25

51 109 15.15 KSRB 15-3.2: Providing 18mm thick cement plaster in single

coat with cement mortar 1:3 to brick masonry including rounding

off corners wherever required smooth rendering, providing and

removing scaffolding, including cost of materials, labour, curing


Sqm 1404.450 211.00 296338.95

52 110 15.18 KSRB 15-3.8 Providing 20 mm thick cement plaster in single

coat with Cement Mortar 1:3 to brick masonry including

rounding off corners wherever required smooth rendering .

Providing and removing scaffolding including cost of all

materials, labour,curing complete as per specifications .

Ground Floor Sqm 694.080 225.00 156168.00

First Floor Sqm 439.040 235.00 103174.40

53 110 15.21 KSRB 15-3-13: Providing 12mm thick cement plaster in single

coat with Cement Mortar 1:3 to Ceiling including rounding off

corners wherever required smooth rendering . Providing and

removing scaffolding including cost of materials, labour,curing

complete as per specifications .

Sqm 575.010 167.00 96026.67

54 110 15.30 Providing rough cement plastering 15mm thick in single coat

with cement mortar 1:4, to brick masonry for base of dadooing

works with sand of approved quality, providing and removing

scaffolding, including cost of materials, labour, curing complete

as per specifications Sqm 31.870 152.00 4844.24

55 111 15.33 KSRB 15-7 - Providing lime rendering for plastering to wait and

ceiling including cost of materials, labour, curing complete as

per specifications. Sqm 1979.460 19.50 38599.47

RITES Ltd.,



P. No l No


2014-15

56 111 15.34 KSRB 15.8.1 : Providing and fixing plaster mesh 100 mm wide

manufactured out of hot dipped galvanised iron of nominal

thickness 0.35mm, with a zinc coating of 120 gms per sqm

width, along route of walls chipped for services, junction

between RCC and brick walls including cost of materials ,labour

for fixing, complete as per specifications. (length of mesh only

be measured for payment)m 300.000 28.15 8445.00

57 113 15.51.2 KSRB 15-15.1 : Providing and applying painting in two coats

with plastic emulsion paint of approved brand on wall surface to

give an even approved shade after thoroughly brushing the

surface, free from mortar drops and other foreign matter

including preparing the surface even and sand paper smooth,

cost of all materials , labour, complete as per specifications.

Sqm 1979.460 80.00 158356.80

58 114 15.55 KSRB 15-17.1 : Applying priming coat over new wood surface

and / or wood based surface with whilte lead paint priming

including preparing the surface after thoroughly cleaning oil,

grease, dirt and foreign matter, sand papering and knotting

ready mix paint including cost of materials, labour complete as

per specifications. Sqm 91.200 30.00 2736.00

59 115 15.60.1 KSRB 15-17.6: Providing and applying painting Two coats (

excluding priming coat ) on new wood surface and/or wood

based surface with enamel paint to give an even shade

cleaning the surface of all dirt dust and foreign matter, sand

papering including cost of materials, labour complete as per

specifications. Sqm 57.600 78.00 4492.80

60 31 7.1 KSRB 7.1 : Providing and fixing in position collapsible steel

shutters with single or double leaf with vertical channel

20mmx10mmx2mm braced with flat iron diagonals 20mmx5mm

size, with top and bottom rails of T iron sections of 40x40x6 mm

with 38mm dia steel pulleys complete with bolt and nuts, locking

arrangements, stoppers, handles on both sides with 7.5cms

openings at 10 cms. c to c applying a priming coat of red lead

paint. cost of materials, labour, HOM of machinery complete as

per specifications. size of gate 2.4mx1.4m Specification No.

KBS 7.7 / 7.12

Sqm 7.200 4311.00 31039.20

61 31 7.5 KSRB 7.5 : Providing and fixing pull and push type rolling

shutters of approved make out of 18 guage, 75mm wide cold

rolled steel laths of convex corrugation, with side guides and

bottom rail, with interlocking arrangements for steel laths by

means of alternate clips, suspension shaft with High tension coil

type springs two numbers, mounted on specially designed pipe

shaft, with bracket plates, guide channels, ball bearing

arrangements, for inside & outside locking with push & pull

operations complete including pulling hooks, 4Nos. handles with

all fittings and accessories, painted with a coat of red lead paint

(without top cover) cost of materials, labour, HOM of machinery

complete as per specifications. Shutter size 3mx2.8 m

Specification No. KBS 7.10 / 7.12

Sqm 21.600 2987.00 64519.20

62 31 7.6 KSRB 7.6 : Providing and fixing top covers made out of 20

guage M.S. sheet over pull and push rolling shutters bent to

shape including cost of red lead primer coat of painting ,

materials, labour, HOM of machinery complete as per

specifications. Specification No. KBS 7.10.6 / 7.12

M 9.000 608.00 5472.00

RITES Ltd.,



P. No l No


2014-15

63 117 15.75 KSRB 15-18.3 : Providing and applying enamel metal paint one

coat (excluding priming coat ) on previously painted steel or

other metal surface brushing to give an even shade after

cleaning oil, grease, dirt and other foreign matter, including cost

of materials, labour, complete as per specifications.

Sqm 37.800 47.00 1776.60

TOTAL - Part A - KPWD SR Items 8627068.38

Total Quoted Cost of Part 'A' - KPWD - SR Items based on Percentage Quoted

Percentage in

words

Plus / Minus / At par

Amount in Figure

(Rupees)

Amount in Words

(Rupees)

Percentage above / below / at par of KPWD-SR 2014-15 (Gulbarga Circle) to be indicated for the above items

Percentage in

figure

(+) / (-) / At par

RITES Ltd.,


1

SN Description Unit Qty Basic rate Amount in

Rs

PN Item No.

Part B - CPWD SR items

1 72 2.7 Earth work in excavation by mechanical means (Hydraulic excavator) /

manual means over areas (exceeding 30 cm in depth, 1.5 m in width as

well as 10 sqm on plan) including disposal of excavated earth, lead upto

50 m and lift upto 1.5 m, disposed earth to be levelled

and neatly dressed.

2.7.1 Ordinary rock Cum 191.1 244.6 46743.06

2 85 4.2 Providing and laying cement concrete in retaining walls, return walls,

walls (any thickness) including attached pilasters, columns, piers,

abutments, pillars, posts, struts, buttresses, string or lacing courses,

parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,

sunken floor,etc., up to floor five level, excluding the cost of centering,

shuttering and finishing:

4.2.3 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20

mm nominal size) Cum 47.78 6450.00 308181.00

3 88 4.17 Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1

Cement : 3 Coarse sand : 6 graded stone aggregate 20 mm nominal

size) over 75 mm of dry brick ballast 40 mm nominal size well rammed

and consoildated and grouted with fine sand including finishing the top

smoothSqm 84.00 419.30 35221.20

4 150 9.21 Providing and fixing ISI marked flush door shutters conforming to IS:

2202 (Part I) non-decorative type, core of block board construction with

frame of 1st class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face veneers on both

faces of shutters :

151 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws. Sqm 34.80 1909.55 66452.34

5 159 9.96 Providing and fixing Aluminium sliding door bolts ISI marked anodised

(anodic coating not less than grade AC 10 as per IS:1868) transparent

or dyed to required colour or shade with nuts and screws etc., complete.

9.96.1 300 mm X 16 mm Each 45.00 229.65 10334.25

6 159 9.97 Providing and fixing aluminium tower bolts ISI marked anodised (anodic

coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed

to required colour or shade with necessary screws etc. complete:

9.97.2 250 mm x 10 mm Each 45.00 95.25 4286.25

7 160 9.100 Providing and fixing Aluminium handles ISI marked anodised (anodic

coating not less than grade AC 10 as per IS:1868) transparent or dyed

to required colour or shade with necessary screws etc., complete.

9.100.1 125 mm ( for Doors ) Each 60.00 69.80 4188.00

8 160 9.101 Providing and fixing Aluminium hanging floor door stopper ISI marked

anodised (anodic coating not less than grade AC 10 as per IS:1868)

transparent or dyed to required colour or shade with necessary screws

etc., complete.

9.101.1 Single rubber stopper Each 20.00 37.50 750.00

9 177 10.14 Providing and fixing pressed steel door frames conforming to IS: 4351

manufactured from commercial mild steel sheet of 1.60 mm thickness

including hinges, jamb, lock jamb, bead and if required angle threshold

of mild steel angle of section 50x25mm, or base ties of 1.60 mm

pressed mild steel welded or rigidly fixed together by mechanical

means, including M.S. pressed butt hinges, 2.5mm thick with mortar

guards, lock strike-plate and shock absorbers as specified and applying

a coat of approved steel primer after pre-treatment of the surface as

directed by Engineer-in-charge:


Ref. DSR 2014

RITES Ltd.,



Rs

PN Item No.

Ref. DSR 2014

178 10.14.1 Profile B

10.14.1.1 Fixing with adjustable lugs with split end tail to each jambmeter 67.30 377.70 25419.21

10 182 11.5 62 mm thick cement concrete flooring with concrete hardener topping,

under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 20mm nominal size) and top layer

12mm thick cement hardener consisting of mix 1:2 (1 cement hardener

mix : 2 graded stone aggregate, 6mm nominal size) by volume,

hardening compound mixed @ 2 litre per 50 kg of cement or as per

manufacture’s specifications. This includes cost of cement slurry, but

excluding the cost of nosing of steps etc. complete.Sqm 307.32 588.90 180980.75

11 221 13.60 wall painting with acrylic emulsion paint of approved brand and

manufacture yo give even shade

13.60.1 two or more coats on new work Sqm 1133.12 80.50 91216.16

12 346 19.32 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry

brick honey comb shaft with bricks and S.W. drain pipe 100 mm

diameter, 1.8 m long complete as per standard design.

19.32.1 With common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 Nos 2.00 18309.50 36619.00

Part B - CPWD SR Items 810391.22

Add cost index @ 13.33% 108025.15


Total Quoted Cost of Part 'B' - CPWD SR Items based on Percentage Quoted

Percentage above / below / at par of CPWD-SR-2014 of CPWD to be indicated (including Cost Index) for the above items

Percentage in

figure(+) / (-) / At par

Percentage in

wordsPlus / Minus / At par

Amount in

Figure

(Rupees)

Amount in

Words

(Rupees)

RITES Ltd.,


SN Description Unit Qty Rate Amount

Part- C Market Rate Items

1 Providing grooves in plastering on walls 2.50 to

4.00 cms wide and to the required depth as per

design and finished in cement mortar (1:3)

including curing etc., complete m 200.00

2 Supplying and fixing ceramic steel green chalk

board, of size 4 feet X 12 feet, surface sheet

imported from belgium having a thickness of

0.49mm, 8mm thickness of MDF and 0.2mm

thickness of GI sheet at the back covered with

powder coated aluminium frame

Cum 3.00

3 Supply, delivery, installation, testing,

commissioning of vertical centrifugal submersible

pump of 6.5HP capable of pumping 335 lpm

against an approximate total head of 40m from all

causes, including providing 4Cx4sqmm 440V flat

core double sheathed waterproof submersible

cable, Star Delta starter, control panel with dry

run preventer, overload protection and backup

protection and capacitor as required, installed

inside a weather proof kiosk with locking

arrangement of approved design near the

borewell, including making necessary electrical

connections from mains to the starter panel and

from starter panel to the pump. Including

providing and fixing gun metal gate valve and non-

return valve of 50mm n.b on the delivery side of

the pump. Submersible pumps may be of Atlanta/

KSB/ Kirloskar/ CALAMA/ Suguna makes.

No 1

Total - Part C - Market Rate Items

The bidder is required to quote his rates in

figure and words for Part C-Market Rate items


Total Amount in Words (Rupees)

RITES Ltd.,


SN Description of the Item Unit Qty Rate Amount

Part D - Panchayat Raj SR 2012-13

1 Geophysical investigation of site for sinking

borewell for supplying drinking water to the

habitation either through hand pump, MWS or

PWSS by vertical electrical sounding by adopting

Venner or Schlumberger's method, including

reconnaissance survey of Geological formation,

geophysical investigation of existing ground water in

the vicinity indicating the location of site,

recommended depth of casing pipe required to seal

the top unconsolidated formation including an extra

depth of 1m in consolidated formation for proper

seating of casing pipe, depth of drilling required to

cover full depth of aquifer proposed to be tapped,

probable yield and other information required

including transportation of instrument and

accessories to work site, engaging technical

personnel and labour required etc.,

Each BW 1.00 1882.00 1882.00

2 Sinking Bore Well of 165mm dia clear using super

fast hydraulic rig of capacity 250 PSIG & above 900

CMF & above in all strata including over burden

upto 20mtrs fixing of casing pipes, collars and cap

with necessary cutting, threading and welding

including transportation of rig and supporting

vehicle, crew charges and cost of consumables

etc., complete including yield testing at the final

depth with a minimum working of compressor for

one hour (excluding cost of casing pipes, collars,

cap etc.)

0- 50 mtrs RMtr 50.00 306.00 15300.00

50- 100 mtrs RMtr 50.00 400.00 20000.00

100- 150 mtrs RMtr 50.00 445.00 22250.00

150- 200 mtrs RMtr 50.00 470.00 23500.00

3 Yield testing of Borewell at Final depth with a

minimum of 10 hours continuously with the help of

pump testing unit including the cost of

transportation charges, crew charges and cost of

consumables Each BW 1.00 8197.00 8197.00

Part D - Panchayat Raj SR Items 91129.00

Total Quoted Cost of Part 'D' - Panchayat Raj SR 2012-13 Items based on Percentage Quoted


IN

KPWD Panchayat

Raj SR Bangalore

2012-13 Item No.

9.4

KPWD

Panchayat Raj

SR Bangalore

2012-13 Item

No. 9.1

9.1.1

KPWD

Panchayat Raj

SR Bangalore

2012-13 Item

No. 9.9

9.1.2

9.1.3

9.1.4

Amount in

Figure (Rupees)

Amount in

Words (Rupees)

Percentage above / below / at par of KPWD-Panchayat Raj SR Bangalore 2012-13 to be indicated (including Cost

Index) for the above items

Percentage in figure (+) / (-) / At par

Percentage in words Plus / Minus / At par

RITES Ltd.,


Part A - KPWD SR 2014 - 15

POINT WIRING

Point wiring using Copper wire without switch.

1 2.3 5 Supplying and wiring adopting loop system in

existing PVC Conduit / casing capping using

1100V grade, COPPER conductor flexible

multistrand FRLS PVC insulated, 2x1.5Sq.mm

Cable confirming to the GTP without switch, the

other end of the wires shall be terminated with

sufficient loose length in a wood/PVC round block

complete for each outlet.

GROUP A

a 2.3.1 5 Short point up to 3 Mtr from tapping point to out let

via switch box Point 10 144.00 1440.00

b 2.3.2 5 Medium point above 3 Mtr up to 6 Mtr from tapping

point to out let via switch box Point 32 215.00 6880.00

c 2.3.3 5 Long point above 6 Mtr up to 10 Mtr from tapping


d 2.3.4 6 Two outlet in a row, above 3 Mtr up to 6Mtr from

tapping point to out let via switches Point 22 423.00 9306.00

2 3.5 15 Supplying and flush mounting powder coated /

galvanized metal box suitable for mounting

modular switch plates. The box should be firmly

flush mounted after due groove cutting in

Brick/Stone/C.C wall

a 3.5.1 15 1-3 Way Each 28 91.00 2548.00

b 3.5.2 15 4-5 Way Each 66 98.00 6468.00

c 3.5.3 15 6 Way Each 20 121.00 2420.00

d 3.5.4 15 8 Way Each 12 140.00 1680.00

e 3.5.5 16 10-12 Way Each 12 159.00 1908.00

3 3.6 16 Supplying and fixing superior quality modular

switch mounting polycarbonate plate with

necessary supporting back plate with required nos.

of machine screws, bolts nuts etc., complete on

the existing metal/PVC box.

a 3.6.1 16 1 to 3 Module Each 28 109.00 3052.00

b 3.6.2 16 4 Module Each 66 122.00 8052.00

c 3.6.3 16 6 Module Each 20 173.00 3460.00

d 3.6.4 16 8 Module Each 12 200.00 2400.00

e 3.6.6 16 12 Module Each 12 267.00 3204.00

4 3.7 16 Supplying and fixing of modular switch/

Socket/stepped electronic fan regulator/

dimmer/telephone socket etc on existing modular

switch plate as per IS 3854 and IS 1293

GROUP A

a 3.7.1 16 6 Amps one way. Each 140 63.00 8820.00

b 3.7.3 16 6 Amps 3way socket. Each 40 95.00 3800.00

c 3.7.4 16 Stepped Fan Regulator. Each 24 286.00 6864.00

d 3.7.8 16 6 Amps Bell push Each 2 87.00 174.00

e 3.7.9 16 32 Amps DP switch Each 60 164.00 9840.00

f 3.7.10 16 6/16 Amps universal socket Each 60 147.00 8820.00

g 3.7.11 16 TV / Telephone socket Each 8 82.00 656.00

h 3.7.12 16 RJ 45 / I.O. outlet Each 12 204.00 2448.00

Construction of Govt. ITI at Humnabad in Bidar District - Electrical Works

SN Item No P.No. Description Unit Qty Rate Amount

RITES Ltd.,



5 1.12 3 Supplying and Fixing Metal Fan Box with Round

Hook.

No 24 92 2208

1.2 2 Concealed Conduit System

6 Supplying heavy gauge PVC conduit pipe ……mm

dia .......mm thick confirming to IS 2509 with

suitable size bends, metal/PVC junction boxes

adhesive paste etc., and running before concreting

the slab. The conduit should be tied to the

reinforcement rods by using binding wires and

unused ways of junction boxes and pipe ends

should be covered using PVC end enclosures. run

with 18SWG GI fish wire wherever necessary

a 1.2.1 2 19/20 mm dia 2mm thick Mtr 540 43.00 23220.00

b 1.2.2 2 25 mm dia 2mm thick Mtr 2200 57.00 125400.00

c 1.2.3 2 32 mm dia 2.5mm thick Mtr 100 90.00 9000.00

Groove Cutting

7 1.3 2 Supplying heavy gauge PVC Conduit Pipe ----- dia -

- mm thick with suitable size bends, metal junction

boxes adhesive paste etc., by groove cutting in the

wall and fixing by bracing U or J hooks and cement

Plastering up to the wall surface and run with 18

SWG GI fish wire run throughout the conduit

wherever necessary.

a 1.3.1 2 19/20mm dia 2mm thick Mtr 160 56.00 8960.00

b 1.3.2 2 25mm dia 2mm thick Mtr 360 58.00 20880.00

c 1.3.3 2 32mm dia 2.5mm thick Mtr 100 88.00 8800.00

8 1.8 3 Supplying and fixing of PVC casing and capping

on the wall or ceiling using necessary materials

like bends, screws at an interval of 300mm …. Etc

as required.

a 1.8.2 3 25mm Mtr 160 26.00 4160.00

b 1.8.4 3 38mm Mtr 160 39.00 6240.00

c 1.8.5 3 50mm Mtr 160 43.00 6880.00

9 2.5 6 Wiring for lighting/power circuit using one of FRLS

PVC insulated 1100v grade, multistrand Copper

with low conductor resistance single core wire in

open or concealed system of wiring with specified

IS-694:1990 & confirming to GTP of GROUP-A

a 2.5.2 6 1.5 sqmm Mtr 2300 18.60 42780.00

b 2.5.3 6 2.5 sqmm Mtr 1800 29.20 52560.00

c 2.5.4 6 4 sqmm Mtr 3200 42.10 134720.00

d 2.5.5 6 6 sqmm Mtr 350 63.80 22330.00

e 2.5.6 6 10 sqmm Mtr 680 108.00 73440.00

DISTRIBUTION BOARDS

10 6.17 47 Supplying and fixing regular MCB distribution

boards on wall / wood board / flush mounting

using required clamps, bolts, nuts etc., with

provision for fixing suitable type capacity MCB's

single phase / 3 phase / single door with powder

coated painting. Made out of 14 SWG MS

enclosure.

I - Single Door

a 6.17.1 47 4 way SP&N Each 12 706.00 8472.00

( Only for Work shops )

II - Double Door

b 6.17.7 47 4 way TP&N Each 2 2399.00 4798.00

RITES Ltd.,



c 6.17.6 47 12 way SP & N Each 2 1622.00 3244.00

11 6.15 46 Supplying and fixing regular MCCB distribution

Panel confirming to IS 8828, on wall / wood board /

flush mounting using required clamps, bolts, nuts

etc., with provision for fixing of suitable type

capacity MCCB's as an incomer for 3 phase

Double door with necessary bus bar completely

wired to use on 440 Volts 3 phase 4 wire powder

coated painting etc., complete with a provision for

fixing of single / three phase suitable capacity

MCCB / MCB's as outgoings confirming to IS

8828.

a 6.15.2 46 8 way Each 3 9095.00 27285.00

12 6.16 47 Supplying and fixing miniature circuit breakers on

existing MCB distribution boards using necessary

fixing materials and 'C' Type curve , indicator

ON/OFF, energy cross-3 with Short circuit

breaking capacity of 10K and complete wiring as

required confirming to IEC 60898.

a 6.16.1 5-32 Amps SP Each 80 418 33440.00

b 6.16.3 5-32 Amps DP Each 2 849 1698.00

c 6.16.5 5-32 Amps TPN Each 12 1547 18564.00

d 6.16.6 40-63 Amps TPN Each 2 1936 3872.00

13 6.18 47 Supplying, fixing and wiring Earth Leakage

Miniature Circuit Breaker [ELMCB] 240/450V up to

300mA sensitivity on existing wood/panel board.

a 6.18.2 47 32-40 Amps 2 pole Each 2 2623.00 5246.00

b 6.18.3 47 32-40 Amps 4 pole Each 2 2936.00 5872.00

14 6.43 50 Supplying and fixing of Metal Socket set of 2pole

and earth plugs and socket for incorporating SP

and TP MCB (Without MCB ). The entire plug and

socket shall b mounted in a Thermoplastic /

powder coated metal box & wired Completely.

A) SP & N

a 6.43.2 b) 20 Amps Each 4 918.00 3672.00

SUPPLY OF FITTING

15 4.7 20 Supplying Box Type Suitable for 28 W T5 Single /

Twin lamp & suspension mounted luminaire &

optical reflector,prewired with HF Electronic

Ballast,push fit type lamp holders & main

connectors. Channel cover shall be made of

CRCA MS Sheet and finishing is done with stove

enamelled white with end caps made of

engineering Plastic.

Group - A

a 4.7.1 1 X 4'-28 Watts Each 66 990.00 65340.00

b 4.7.2 2 X 4'-28 Watts Each 6 1680.00 10080.00

16 4.23 24 Supplying CFL mirror light fitting with 1x11W

CFL lamp, choke, Perspex cover and completely

wired for use on 230V 50Hz AC supply.

Each 2 648.00 1296.00

RITES Ltd.,



17 4.17 22 Supplying High pressure Metal halide street

light luminary suitable for use with high pressure

metal halide lamp with integrated control gear &

grey color powder coated. The fitting shall be non

corrosive pressure die cast aluminum housing with

high purity anodized aluminium reflector with

EPDM Gaskets suitable for Outer Dia of pole

40mm - 60mm. Cable Entry through a cable gland

with toggle clips. IP65 Protection for both optical &

Electrical Compartment. Bottom cover may be with

Poly carbonate/tempered/ toughened glass.

Luminaire efficiency should be >60 % & ambient

temperature > 35 deg C. High Intensity Discharge

Electro Magnetic Ballast with Copper winding of

Orthocyclic winding coil. Class H insulated dual

coated copper wire. Compliance to IEC 61347-2-9

Safety & IEC 60923 - Performance. Winding

Temperature for HID Ballast Tw = 130 deg C &

temperature rise ?T = 70 deg C. Luminaire shall

be suitable to operate on 230/250 Volts 50 Hz AC

supply finish including wiring, ignitor, condenser.

SS Toggles for opening front hingeable glass.

a 4.17.2 23 150Watts Each 1 6300 6300.00

18 9.3 78 Supplying capacitor type ceiling fan complete

with down rod blades, shackle, canopies etc., for

operation on 230 volts, 50 cycles. Single phase

AC supply conforming to ISS-374-1979 and with

double ball bearing system.

9.3.1 48" Sweep (1200mm)

a 9.3.1.1 78 Regular model Each 24 2376.00 57024.00

19 9.2 78 Supplying of 1440rpm heavy duty exhaust fan

with bracket blades suitable to operate on 230V

50Hz, AC Supply complete.

a 9.2.1 78 12" Sweep (300mm) Each 10 3654.00 36540.00

20 4.2 20 Supplying and fixing PBBC/Bakelite straight or

slant batten holder and wiring with 60 W / 230

volts lamps. Each 10 88.00 880.00

21 16.1 104 Supplying and fixing one of 230 volts bell or

buzzer and a flush type bell push with gang box

fixed on necessary wooden or rawl plugs using NF

screws. Each 2 145 290.00

FIXING CHARGES

22.0 17.2 108 Supplying and Fixing........mm dia class A GI pipe

bracket up to 2.7 meters long terminated with a

reducing collar of 40x25mm to which extra pipe of

175mm length is fixed for fixing MV/SV/MH/FTL

street light fitting of all capacities on

rail/RCC/wall/tubular pole, using suitable clamps,

bolts ,nuts and wiring using suitable capacity wires

etc complete.

a 17.2.2 108 Using 32mm dia G.I.pipe Each 1 1140.00 1140.00

RITES Ltd.,



23 17.7 108 Fixing all types and all capacities of fluorescent /

false ceiling / spot light / CFL / LED fittings

indoor on the wall / ceiling/ rafters / girders

using 23/0.0076” twin twisted PVC insulated

wires, required Nos of round blocks and clamps

a 17.7.1 108 On wall / ceiling / Rafter / Girders Each 74 98.00 7252.00

24 17.8 109 Fixing a ceiling / Wall mounting fan of all

capacities and all types to the existing 'S' hook

with fan regulator to the existing board together

with supplying and fixing 5 amps. ceiling rose,

necessary length of 23 / 0.0076 inch PVC

insulated twin twisted copper wire and wiring.

Each 24 139.00 3336.00

25 17.12 109 Fixing one exhaust fan in the nitch already left in

the wall with bolts and nuts and 5 amps. Ceiling

rose with sufficient length of 23 / 0.0076 inch PVC

insulated twin core wire. Each 10 412 4120.00

26 17.5 108 Fixing halogen/metal hallide / SVL / IL / LED

floodlight fitting over existing pole / wall ceiling

including clamps, bolts, nuts and wiring using

suitable capacity wires. Each 1 176.00 176.00

27 11.1 85 Supplying and drawing UTP-CAT 6E LAN cable.

Mt. 180 23.00 4140.00

28 11.2 85 Supplying and drawing PVC flexible one pair

telephone unarmoured tinned copper cable.

a 11.2.2 85 2 Pair mtr 132 13 1716.00

29 1.4 2 Supplying and fixing sheet metal box made out of

18 SWG sheet metal with necessary holes for

cable/conduit entry as required with one coat of

primer of approved make etc.

a 1.4.7 2 200 x 200 x 65 mm Each 4 157.00 628.00

30 7.4 55 Supplying of 1.1 KV LT UG cable having

aluminium conductor PVC insulated, extruded

inner sheated , galvanized , steel strip (except 2C

X 10 Sq.mm wire armoured) confirming to IS -

3975 : 1990 (No. of strip indicated in GTP) &

extruded PVC outer sheated armoured cable with

specified IS - 1554 Part - 1:1988 & confirming to

GTP of Group - A.

7.4.4 55 4 core 16 sqmm Mtr 200 140.40 28080.00

31 7.8 61 Labour charges for laying of 1.1 KV class UG

cable in existing trench GI pipe / stoneware pipe /

on wall / on pole as required.

In existing trench / duct.

7.8.1 61 6 sqmm to 16 sqmm Mtr 200 10.80 2160.00

.

32 7.9 61 Digging of trench of 0.6m deep X 0.50 mtr wide

refilling the trench to the required ground level and

consolidating etc., complete. (As per Civil SR

KSRB I - 2, P - 7)

7.9.2 62 In soil (hard) Mtr 100 106.00 10600.00

RITES Ltd.,



33 7.10 62 Providing and filling sand in excavated trench to

cover already laid UG cable to adepth of 150 mm

all - round the cable. Mtr 100 103.00 10300.00

34 7.14 62 Supplying and fixing of heavy duty cable glands

suitable for UG cable of 1.1 KV class (metal only)

7.14.2 62 25 mm dia Each 6 86.00 516.00

35 7.21 64 Supplying tinned copper lugs and crimping and

wiring to terminal point for wire of the following

sizes.

7.21.6 64 16 sqmm Each 24 11.31 271.44

EARTHING

36 7.2 55 Supplying fixing and wiring earth electrode for

grounding of lifts, transformers, DG sets etc.

using 40mm dia 2.9mm thick 2.5 mtr long GI pipe

with GI funnel with mesh and suitable size reducer

fixed on the top of the earth electrode. The funnel

should be enclosed in a CC chamber of

400x400x400mm with a cast iron cover. The earth

electrode shall have staggered holes of 12mm dia

and the electrode should be covered 150mm

alround with alternate layers of salt and charcoal

from the bottom of the CC chamber. The

connection from the electrode is to be established

through GI strip using GI bolts and nuts.

Each 3 4317.00 12951.00

37 7.3 55 Supplying and running of GI/Copper strips for

grounding connections, using necessary fixing

materials as required.

GI strip

a 7.3.1 55 25 x 3 mm Mtr 60 77.00 4620.00

c 7.3.10 55 600 x 600 x 3 mm copper plate Each 1 7148.00 7148.00

38 7.22 64 Supplying and running GI/Copper conductor for

grounding and (along with other wires in conduit

system of wiring) using necessary suitable size

clamps, nails, guttas/spacers etc.,

Copper Wire.

b 7.22.6 64 8 SWG Mtr 60 107.70 6462.00

RITES Ltd.,



39 7.12 62 Supplying and fixing of class A (medium duty) GI

pipe of wall thickness not less than 3.25mm on

pole/wall/drain crossing with necessary clamping

arrangements for UG cable of 1.1 KV.

a 7.12.2 62 50mm Mtr 20 391.00 7820.00

Part A - KPWD SR Items - Electrical works 1059199.44

Total Quoted Cost of Electrical Items based on Percentage Quoted

Amount in Figure

(Rupees)

Amount in Words

(Rupees)

Percentage in

words


Percentage above / below / at par of KPWD-SR 2014-15 for Electrical Works to be indicated for all the above items

Percentage in

figure

(+) / (-) / At par

RITES Ltd.,


SN Description of Work Unit Qty Rate Amount

Part B - Market Rate Items

Sub MV Panel

1 Supply, installation, testing and commissioning of LT

Sub MV Panel fabricated out of 16 SWG sheet steel

metal floor mounting type with all normal practice like

derusting, degreasing, phosphating, powder coated to

the approved make as per specification, comprisiing of

the following:-

Incomer

I. 125 A 3P MCCB 35 KA breaking capacity - 1No.

ii. 250A Al Bus bar (RYBN)

iii. RYB phase indication lamps - 1set

iv.0-500 V Voltmeter with selector switch -1no

v.0 - 300 A Ammeter With selector switch-1no

Outgoing

iii. 63 A 4Pole 16 KA MCCB - 12 nos.

iii. 40 A 4Pole MCB - 3 nos. Nos 1.00

2 Supplying and fixing Moulded Case Circuit Breaker

(MCCB) over the existing wood / panel board using

necessary screws, bolts, nuts and wiring complete.

Protection of Overload and Short circuit with thermal

Magnetic / Micro processor release and Earth Fault as

per IS - 13947. (Icu = Ics)

63 Amps 16 KA (Three Pole) Each 3.00

Part B - Market rate Items - Electrical works

The bidder is required to quote his rates in figure

and words for Part B-Non SR items of Electrical

works

Construction of Govt. ITI at Humnabad in Bidar District - Electrical Works


RITES Ltd.,

For and on behal of DET 25 Signature of the Bidder

SN DESCRIPTION AMOUNT

Civil Works


2 Part B - CPWD SR Items `

3 Part C - Market rate Items `

4 Part D - Panchayat Raj SR Items `

Electrical Works


2 Part B - Market rate Items `

TOTAL - Schedule I `

TOTAL

(in Words) - Rupees

Construction of Govt. ITI at Chincholi in Kalburgi District

ABSTRACT - Schedule I

RITES Ltd.,



P. No l No

Part- A - KPWD SR Items

1 132 18.13 KSRRB M200-10.1. Clearing and grubbing road land including

uprooting rank vegetation, grass, bushes, shrubs, saplings

and trees girth up to 300 mm, removaL of stumps of trees cut

earlier and disposal of unserviceable materials and stacking

of serviceable material to be used or auctioned, including

removal and disposal of top organic soil not exceeding 150

mm in thickness complete as per specifications. I. By Manual

Means: A. In area of light jungle. MORTH Specification No.

201

Ha 0.150 42114.00 6317.10

3 5 2.4 KSRB 2-2.2: Earth work excavation for foundation of

buildings, water supply, sanitary lines and electrical conduits

either in pits or in trenches 1.5m and above in width in Hard

soil not exceeding 1.5m in depth, including dressing the

bottom and sides of pits or trenches, stacking the excavated

soil clear from edges of excavation with lead upto 50 m after

breaking of clods complete as per specifications. Specification

No. KBS 2.1(b)/2.3.5Cum 211.810 244.00 51681.64

4 5 2.6 KSRB 2-2.4: Excavation 1.5m and above in width in soft rock

without blasting for foundation of buildings, water supply,

sanitary lines and electrical conduits either in pits or in

trenches not exceeding 1.5m in depth, stacking the excavated

stuff from edges of excavation with lead upto 50m including

cost of labour and HOM of euipment complete as per

specifications. Specification. No KBS 2.1.d / 2.9.4 / 2.18 / 2.19

Cum 211.810 758.00 160551.98

5 6 2.10 KSRB 2.3 : Filling available excavated earth ( excluding rock )

in sides of foundations upto plinth in layers not exceeding 20

cms. in depth, compacting each deposited layer by ramming

after watering with lead upto 50 m. and lift upto 1.5 m.

including cost of all labour complete as per specifications.

specification. No. KBS 2.9Cum 614.720 109.00 67004.48

6 9 3.2 KSRB -3.2: Providing and injecting chemical emulsion for Pre-

constructional Anti-Termite Treatment, creating continuous

chemical barrier under and around the column pits,walls

,trenches,basement excavation,top surface of the plinth filling,

junction of wall and floor, along the external perimeter of

building, expansion joints, over the top surface of

consolidated earth on which apron is to be laid, surrounding of

pipes and conduits, with chloropyriphos emulsifiable

concentrates of 20%concentration, including cost of chemical,

diluting in water to one percent concentration, labour, HOM of

equipments, complete as per specifications.(Plinth area of the

building at ground floor only shall be measured ) Specification

No. KBS 3.2.6 / 3.2.7

Sqm 637.000 100.00 63700.00


concrete of mix M7.5 with OPC cement @ 180kgs, with

40mm and down size graded granite metal coarse aggregates

@ 0.85cum and fine aggregates @ 0.57cum machine mixed,

concrete laid in layers not exceeding 15cms, thick, well

compacted, in foundation and plinth including cost of all

materials, labour, HOM of machinery, curing complete as per

specifications. specification No KBS 4.1,4.2

Cum 86.200 4329.00 373159.80


SN Gulbarga SR -

2014-15

Rate Amount

RITES Ltd.,



P. No l No

SN Gulbarga SR -

2014-15

Rate Amount


concrete of M 10 with OPC cement @220 kgs with 20mm and

down size graded granite metal coarse aggregates @ 0.84

cum and fine aggregates @ 0.56 cum, machine mixed,

concrete laid in layers not exceeding 15 cms, thick, well

compacted, in foundation and plinth and cills, inclduing cost of

all materials, labour, HOM of machinery, curing complete as

per specifications. Specification No KBS 4.1,4.2

Ground Floor Cum 13.780 4776.00 65813.28

First Floor Cum 7.590 4826.00 36629.34

9 13 4.12 KSRB 4-2.7: Providing and laying in position reinforced

cement concrete of design mix M 25 with OPC cement @

340 kgs with 20mm and down size graded granite metal

coarse aggregates @ 0.70 cum and fine aggregates @ 0.47

cum, with superplastisiser at 3.0 lts. conforming to IS103-

1999 reaffirmed -2008, machine mixed, concrete laid in

layers not exceeding 15 cms, thick, vibrated for all works in

foundation plinth and ground floor level for roof slabs,

staircase, lintels, retaining wals, return wall, wall (any

thickness ) including attached plasters, columns, piers,

abutments, pillers, posts, struts, buttresses, string or lacing

courses, parapets, coping, bed blocks, anchour blocks, plain

windows cills, fillets etc., inclduing cost of all materials, labour,

HOM of machinery, curing complete as per specification No

KBS 4.1,4.6

Ground floor Cum 279.600 5805.00 1623078.00

First floor Cum 1.730 5855.00 10129.15

10 15 4.28 KSRB 4-6.1 : Providing and removing centering, shuttering,


foundations, footings, bases of columns for mass concrete


specifications. Specification No. KBS 4.6.2Sqm 158.800 211.00 33506.80

11 15 4.29.2 KSRB 4-6.2: Providing and removing centering, shuttering,

strutting, propping etc., and removal of form work for flat

surface such as suspended floors, roofs, landings, balconies

and likes, thickness up to 200mm including cost of all

materials, labour complete as per specifications. for 0-5m

Height , Specification No. KBS 4.6.2Sqm 637.00 530.00 337610.00


strutting, propping etc., for columns, pillars, piers, abutments,

post and struts, square /rectangular / polygon in plan including

cost of all materials, labour complete as per specification.


Ground floor Sqm 416.52 346.00 144115.92

First floor Sqm 66.82 351.00 23453.82


strutting, propping etc., an removal of form work for sides and

soffits of beams, beam haunchings, cantilever girders,

bressumers and lintels not exceeding 1m in depth including

cost of all materials, labour complete as per specifications.


RITES Ltd.,



P. No l No

SN Gulbarga SR -

2014-15

Rate Amount


strutting, propping etc., for chajjas, corbels etc., including

edges including cost of all materials, labour complete as per

specification. Specification No.KBS 4.6.2 Sqm 31.68 259.00 8205.12



stairs(excluding landing) except spiral staircase including cost

of all materials, labour complete as per specification.

Specification No. KBS 4.6.2Sqm 23.930 460.00 11007.80

16 17 4.46 KSRB 4.9.2 : Providing T.M.T steel reinforcement for R.C.C

work including straightening, cutting, bending, hooking,

placing in position, lapping and / or welding wherever

required, tying with binding wire and anchoring to the adjoining

members wherever necessary complete as per design (laps,

hooks and wastage shall not be measured and paid) cost of


specifications. Specification No. KBS 4.6.3

4.46.2 For TMT bars Fe 500 Ton 23.910 69243.00 1655600.13

17 23 5.3 KSRB-5.1-3 : Providing and cosntructing Granite/ trap/ basalt

rubble stone masornry in foundation cement mortar 1:6,

(Uncoursed) bond stones at two m. apart in each course

including cost of materials, labour, curing complete as per

specifications. KBS 5.1.12 Cum 43.050 2766.00 119076.30

18 23 5.6 KSRB-5.2.3: Providing and constructing Granite/ trap/ basalt

size stone masornry in foundation cement mortar 1:6, stone

hammerd dressed in courses not less than 20 cms high, bond

stones at two m.apart in each course including cost of

materials, labour, curing complete as per specifications. KBS

5.1.13Cum 36.900 4326.00 159629.40

19 25 5.27 KSRB 5-14: Providing and constructing precast concrete solid

blocks with compressive strength not less than 35Kg/Sqm

with cement mortar 1:4 masonry (quoin, jamb, closer blocks)

with solid concrete blocks of size 40X20X20cms conforming to

1.S: 2185/1965 in superstructure including cost of materials,

labour charges, scaffolding, curing complete as per

specifications.

Ground Floor Sqm 765.160 880.00 673340.80

First Floor Sqm 193.700 910.00 176267.00

20 25 5.28 KSRB 5-15: Providing and constructing non load bearing wall

with cement concrete solid blocks with compressive strength

not less than 35Kg/Sqm with cement mortar 1:4 masonry

(jamb, closer blocks) with solid concrete blocks of size

40X10X20cms (l X b X h)conforming to 1.S: 2185/1965 in

superstructure including cost of materials, labour charges,

scaffolding, curing complete as per specifications.

Sqm 88.920 634.00 56375.28

RITES Ltd.,



P. No l No

SN Gulbarga SR -

2014-15

Rate Amount

21 37 7.17 KSRB 7.17 : Providing, fabricating, assembling and fixing in

position aluminium doors using following aluminium mat finish

or glossy finish, outer frame plain section 101.6x44.45mm

thickness 3.18mm, section weight 2.404 kg/m, door shutters

vertical section 44.62x44.45mm thickness 3.18mm, section

weight 1.505kg/m, top section 47.62x44.45mm thickness

3.00mm, section weight 1.426kg/m bottom section

114.3x44.45 thickness 3.18mm, section weight 2.646kg/m,

door central section 49.91x44.45mm thickness 3.00mm,

section weight 1.495 kg/m glazing clips 19x17.3x11mm

thickness 0.9mm section weight 0.124kg/m; aluminium

sections cut to length joint metred cornersgrinded, the

shutters pivoted opening arrangement with heavy duty

aluminium alloy automatic door closures floor mounted,

providing and fixing standard approved accessories, such as

aluminium handle for full width or length, tower bolts, lock,

pivots: P.V.C. or rubber gasket with 5.5m. thick plain glass for

top and bottom panel; aluminium sections treated for removal

of any rust and prevention of further rust formation,

and coated with greasy materials for non-adherance of

mortars or any other sticky materials; the assembled frame

fitted with the corner angles, strips and fitted with screws, rawl

plugs or teakwood gutties to R.C.C. columns or masonry on

sides. beams and flooring in bottom. including cutting,

chistling and making good with cement mortar to match the

surface; all the frames throughly cleaned free from rust, scale,

or dirt including cost of materials, fixtures, labour and HOM of

machinery complete as per specifications.

7.17.2 using aluminium section powdered coated to a minimum of 60-

70 microns with exterior durable pure polyester grade powder

of approved quality.Sqm 2.880 6080.00 17510.40

22 39 7.24 "Providing and fixing cold rolled prepainted steel windows of

IS standards, made out of 0.6mm thick deep drawing quality

galvanised on both sides 120gms/sq.mtr. Primer coat upto 5

microns with thermosetting epoxy resin and finish painted with

a polyester based paint 20 microns thick. The size of profiles

is approximately 46 x 52mm for external frames, 46x46mm

section for shutters, 46x70mm section for centre

mullion/transom and 18x31mm section is for fixing glasses.

The section should be cut to length joint mitred and

assembling by means of corner brackets made out of cold

rolled cold annealed strips of 1.2mm thick duly galvanised and

fixed with nickle plated self taping screws.The shutters are

provided with approved quality of fixtures like handles made

out of zamac alloy die cast and powder coated, receiver made

out of glass filled nylone and hinges made out of

CRCA powder coated. 4mm thick glass should be fixed with

EPDM gaskets. Guard bars fabricated out of 10mm square

bright bars shall be fixed horizontally at 125mm C/C by

rivetting to the external frame. The above frames are fixed to

the concrete / masonry walls by means of self expanding

screws.â€ with 4mm float glass with gaurd bars

39 7.24.1 4mm float glass with gaurd bars Sqm 75.960 3520.00 267379.20

RITES Ltd.,



P. No l No

SN Gulbarga SR -

2014-15

Rate Amount

23 42 7.35 Providing and fixing M.S hand railing for Balcony/staircase

etc., with 50mm dia M.S hollow pipe of 14 gauge, welded to

20mmX20mm M.S. square rod placed vertically, spaced at

100mm at regular inetrvals of 600mm. These veryical rods

laterally tied to 3 horizontal rods spaced at equal interval.

These assembly is fixed to concrete by using expansion bolts

and welding the same to reinforcement bars and making good

the surface. ALl the joints and sections should be cut to

length, welded and grinded wherever necessary etc.,

complete. The work includes cost of all materials, labour

charges for all items of work, hire charges for welding, cutting

and grinding equipment, and electricity charges etc., complete

as per specification and drawing

Sqm 10.000 2615.00 26150.00

24 46 8.3 KSRB 8.3-1 : Providing and laying to required line and slope

roofing with corrugated asbestos cement sheet 6mm. thick

fixed with galvanised iron J or L hooks, bolts and nuts 8mm.

dia C.I plain and bitumen washers over the existing purlins,

rafters and trusses including cost of materials, labour,

complete as per specifications. Specification No. KBS 8.5

Sqm 35.000 394.00 13790.00

25 59 9.93 Providing and fixing factory made single leaft rigid GRP

Sandwich composite door shutter of 32mm thick, laminated

with two GRP skins with wood grain finish, fabricated using

U.V-stabilized Isopathic Gelcoat and on layer of 45 gsm E-

class Chopped strand Mat (CSM), impregnated with

orthopthalic polyster resin. The thickness of the skins shall not

be less than 1.5mm. Expanded Polystyrene (EPS) structural

foam panel of 29mm thickness and a density of 20Kg/m3 shall

be used as core mterial. Wooden reinforcements made of

seasoned Salwood block of cross section not less than

28mmX32mm and also necessary salwood reinforcements for

fixing the metal fittings such as tower bolts, aldrops, handles

etc shall be provided. A structural adhesive compatible with

EPS foam shall be used for bonding the core material, the

salwood reinforcement and the skins.

The material and process for manufacturing the door shutters

shall confirm to RV/TIFAC composites Design Centre

standards and specifications and the door shutters tested in

confirmation to IS 4020-1994. The finish of shutter will be

plain colour White/Ivory/Beige/Light Grey or any other colour

using high quality pigments. Excluding cost of fixtures and

inclusive of supply of shutters to respective work spot.

Sqm 9.450 3200.00 30240.00

26 60 9.96 Providing and fixing 65mm X 125mm GRP Door frame

fabricated using E-Glass Chopped Strand Mat (CSM) U.V -

sablized Isopathlic Gelcoat and Isopthalic resin. The thickness

of the GRP Skin shall not be less than 2.0mm. The door

frame consists of four segments, which are provided with plug-

in-socket arrangement in-situ in the mould. The segments are

plugged in and are joined together by means of screws. The

GRP frame shall be provided with wooden reinforcement on 6

locations for high screw holding capacity for fixing metalling

hold fast and shall be consolidated by filling with medium

density foam/plaster of paris with fibre reinforcement. Six

numbers of 260mmX25mmX5mm size S shaped M.S. flat

hold fast shall be provided with the frame.

m 25.500 565.00 14407.50

RITES Ltd.,



P. No l No

SN Gulbarga SR -

2014-15

Rate Amount

27 67 11.1 KSRB 12-1.1 : Providing and laying in position to required

level or slope 100mm internal diameter salt glazed stoneware

pipes grade A and jointing with stiff mixture of cement mortar

in proportion of 1:1, testing of pipes and joints, including cost

of materials, labour charges complete as per specifications.


28 67 11.2 KSRB 12-1.2: Providing and laying in position to required level






29 68 11.37 KSRB 12-5.1: Construction brick masonry circular type man

hole 0.91m internal diameter at bottom 0.91m and 0.56mt dia

at top with table moulded non modular bricks of class

designation 50 in cement mortar 1:4, inside cement plastered

12mm thick with cement motar 1:3, finished with floating coat

of neat cement , foundation concrete of 1:3:6 mix using 40mm

and down size granite metal and making neccessary channel

in cement concrete 1:2:4 with 20mm and down size granite

metal finished with floating coat of of neat cement wit SFRC

cover and frame (heavy duty, HD-20 grade desination)

560mm internal diameter confirming to IS 12592, total weight

cover and frame to be not less than 182 Kg fixed in cement

concrete 1:2:4 20mm and down size broken granite metal

providing and removing centering shuttering including cost of

material, labour charges HOM of machineries complete as per

specification NO KBS12.4

Nos 1.000 11795.00 11795.00

30 70 11.50 KSRB 12-8.1 : Constructing brick masonry inspection

chamber 455x610mm, and 450mm depth. (clear inside

dimension) for single pipeline, using table moulded non-

modular bricks of class designation 50 in cement mortar 1:5,

C.I cover with frame (light duty) 455x610mm internal

dimensions. total weight of cover with frame to be not less

than 38 kg (weight of cover 23kg and weight of frame 15 kg)

R.C.C. top slab with cement concrete 1:2:4 mix 20mm and

downsize granite metal, foundation concrete 1:5:10 with

40mm and downsize granite metal inside plastering 12mm

thick with cement mortar 1:3, finish smooth with a floating coat

of cement on walls and bed concrete complete as per

standard design including cost of materials, labour charges,

curing complete as per specifications.

Nos 2.000 6106.00 12212.00

31 71 11.52 KSRB 12-8.2: Construction brick masonry inspection chamber

500x700mm and 450mm depth (clear inside dimension) for

pipeline with one or two inlets, using table moulded non

modular bricks of class designation 50 in cement mortar 1:5 ,

CI cover with frame ( light duty) 455x610mm internal

dimension, total weight of cover with frame to be not less

than 38Kg (weight of cover 23kg and weight of frame 15kg)

RCC top slab with cement concrete 1:2:4 mix 20mm and

downsize granite metal, foundation concrete 1:5:10 with

40mm and downsize granite metal inside plastering 12mm

thick with cement mortar 1:3 finished smooth with floating coat

of cement on walls and bed concrete complete as per

standard design including cost of materials, labour charges,

curing complete as per specifications.

Nos 2.000 6927.00 13854.00

RITES Ltd.,



P. No l No

SN Gulbarga SR -

2014-15

Rate Amount

32 74 12.1 KSRB 11.1 : Providing and fixing white vitreous chine clay

water closet Indian type (Sqatting pan) of size 580mm with

foot rests, 100mm S or P tarp, 10 litres low level, PVC

flushing cistren (all are approved make) with fittings, CI /MS

brackets, 32mm dia flush pipe fittings and clamps, overflow

arrangements with special and 25mm mosquito proof coupling

of approved design, painting of fittings and brackets, cutting

and making good the wall and floor wherever required,


specifications. KBS 11. Nos 4.000 3408.00 13632.00

33 74 12.5 KSRB 11.5 Providing and fixing white vitreous china clay

water closet European type (pedestrial type, P trap) with black

solid plastic sheet and lead cover, CP brass hinges, rubber

buffer 10 litres low level PVC flushing chintrens with fittings CI

/ MS bracket 50 mm dia meter flush bend with fitting and

clapms over flow arrangements with special and 25 mm

mosquitto proof coupling of approved design and painting of

fitting and brackets cutting and making good the wall & floor

required including cost of material etc. complete as per

specification no. 11. Nos 4.000 4942.00 19768.00

34 75 12.11 KSRB.11.8.1: Providing and fixing white vitreousss china clay

wall corner type lipt front Urinal basin of size 340x410x265mm

with 5 litres PVC automatic flushing cistern, CI/MS brackets

standar flush pipe and cp brass speraders with brass union

and GI clamps complete painting of fitting and brackets

cutting and making the good wall and floor wherever required

inlcuding cost material labour complete as per specification

No. KSB 11.Nos 1.000 2733.00 2733.00

35 78 12.28 KSRB 11-11.6 : Providing and fixing white vitreous china clay,

angle back wash basin size 600x480mm with a single 15mm

CP brass pillar tap with CI / MS brackets, 32mm CP brass

waste of standard pattern, painting of fittings and brackets,

cutting and making good the wall and floor wherever required,


specifications. No. KBS 11 Nos 4.000 2962.00 11848.00

36 79 12.34 KSRB 11-13.2 : Providing and fixing Laboratoru sink of white

glazed fire clay of size 600x450x200mm with M.S / C.I

brackets , C.P brass chain with rubber plug, 32mm C.P brass

waste, tap with union, brass stop cock complete, painting of

fittings and brackets, cutting and making good the wall and

floor wherever required, including cost of materials, labour

complete as per specifications. KBS11Nos 4.000 3229.00 12916.00

37 79 12.39 KSBR 11-15.1: Providing and fixing 600x450mm bevellead

edge mirror of superior glass with 6mm hard board backing

and fixed to wooden cleat with CP Screws, washers, including

cost of materials, labour complete as per specification.

Nos 4.000 1229.00 4916.00

38 85 12.113.1 Providing and fixing C.I. Nahani trap of approved make

confirming to ISI specification and construction of cistern in M-

15 as per direction (Rate is inclusive of cost of materials and

fixtures and conveyance of materials to work spot) 10x7.5cms

Nos 18.000 220.00 3960.00

RITES Ltd.,



P. No l No

SN Gulbarga SR -

2014-15

Rate Amount

39 88 13.20 KSRB 13-4.1: Making connection GI distribution branch with

GI main of 25 to 40mm nominal bore including cutting and

threading the pipes, providing and fixing Tee, nuts, labour for

all item of works, testing and HOM of equipments complete as

per specifications. Specification No. KBS 13.10

Nos 15.000 330.00 4950.00

40 88 13.23 KSRB13-6.1-1 : Providing and fixing in position brass bib cock

of approved quality 15mm nominal bore including cost of all

materials, labour and HOM of equipments with all leads


13.2.2/13.3Nos 12.000 218.00 2616.00

41 88 13.26 KSRB 13-6.2-2: Providing and fixing in position brass stop

cock of approved quality 20mm nominal bore inlcuding cost of

all materials labour and HOM equipment with all leads

complete as per specification. KBS 13.2.2 /13.3

Nos 10.000 160.00 1600.00

42 87 13.6 KSRB 13-1.6: Providing and fixing to wall, ceiling and floor

galvanised/mild steel tube 50mm dia nominal bore with fittings

(medium grade weight 5.24kg/mtr) B class including cost of all



13.2.14/13.8m 44.000 837.00 36828.00

43 90 13.70 KSRB 13-8.5: Providing and fixing to wall, ceiling and floor,

low density polyethylene pipes 6.00 kgf/sqcm working

pressure 50mm outside diameter with special flange,

compression type fittings, wall clips, making good the wall,

ceiling and floor, including cost of all materials, labour

charges, HOM of equipments and testing complete as per

specifications. Specification No. KBS 13.2.15.1 /13.9

75 mm dia m 75.000 297.00 22275.00

110 mm dia m 75.000 421.00 31575.00

44 90 13.73.4 KSRB 13-8.9 : Providing and fixing to wall, ceiling and floor

high density polyethylene pipes 6.00 kgf / sq.cm working

pressure 110 mm outside diameter with special flange,

compression type fittings, wall clips, making good the wall,

ceiling and floor including cost of all materials, labour

charges, HOM of equipments and testing complete as per

specifications .Specification No. KBS 13.2.15.2 / 13.9

- do -110 mm dia m 90.000 566.00 50940.00

45 91 13.78 KSRB 13-11.1: Providing and placing on terrace, polyethylene

water storage tanks with man hole lid and suitable locking

arrangements, making holes of suitable diameter for inlet,

outlet and over flow pipes, including cost of all materials,

labour, transport charges, HOM of equipments and testing

complete as per specifications (for 1000 litre capacity).

Specification No. KBS 13.22 Nos 1.000 8332.00 8332.00

46 91 13.79 Providing and fixing gun metal wheel valve conforming to IS

specification of approved make as per directions including all

ead and lifts etc., complete

13.79.2 For 20mm dia Each 3.000 365.00 1095.00

13.79.3 For 25mm dia Each 3.000 505.00 1515.00

13.79.4 For 32mm dia Each 3.000 740.00 2220.00

13.79.5 For 40mm dia Each 3.000 940.00 2820.00

13.79.6 For 50mm dia Each 3.000 1440.00 4320.00

RITES Ltd.,



P. No l No

SN Gulbarga SR -

2014-15

Rate Amount

47 87 13.1 KSRB13-1.1 : Providing and fixing to wall, ceiling and floor

galvanised / mild steel tube 15mm dia nominal bore with

fittings (medium grade weight 1.27 kg/mtr) B class including

cost of all materials, labour charges, HOM of equipments and

testing complete as per specifications. Specification No. KBS

13.2.14/13.8

15 mm dia m 50.000 179.00 8950.00

48 87 13.2 20 mm dia m 50.000 218.00 10900.00

49 87 13.5 40 mm dia m 30.000 425.00 12750.00

50 87 13.6 50 mm dia m 200.000 497.00 99400.00

51 102 14.36 KSRB 14.14-5: Providing Ceramic tiles of size 30x30cms of

approved make, shade and size for flooring, treads of steps

and landings laid on a bed of 12mm thick, cement mortar 1:3

mix flush pointing with white cement using colour pigment,

including cost of materials, labour, curing. complete as per

specifications.

103 14.36.2 ……do……. For ceramic tiles of size 30 x 30 cms Sqm 36.800 1006.00 37020.80

52 103 14.41 KSRB 14-17.2: Providing skirling, dado, rises of steps with

colour glazed tiles 6mm thick on lOmm thick cement plaster

1:3 and Jointed with white cement slurry over rough plaster

surface (exculding cost of rough plastered surface which

should be measured and paid separetly) using glazed tiles of

approved make and size including cost of labour ,materials

complete as per specifications. Specification No

KBS14.16,14.17.

103 14.41.1 …..do…….. Colour glazed tiles 15cm x 15cm x 6mm thick Sqm 31.870 1400.00 44618.00

53 106 14.61 Providing and fixing 20mm thick gang saw water cut sadarhalli

grey granite in CM 1:4 proportion, cut to required shape,

pattern with paper joints, finished with cement mortar using

white cement and colour pigments to match the colour of slab

making through jointing with sealant, grooves in joints

including cost of curing.

14.61.1 minimum width of 900 mm Sqm 240.950 1895.00 456600.25

54 109 15.15 KSRB 15-3.2: Providing 18mm thick cement plaster in single

coat with cement mortar 1:3 to brick masonry including

rounding off corners wherever required smooth rendering,

providing and removing scaffolding, including cost of

materials, labour, curing complete as per specifications.

Sqm 1404.450 211.00 296338.95

55 110 15.18 KSRB 15-3.8 Providing 20 mm thick cement plaster in single

coat with Cement Mortar 1:3 to brick masonry including

rounding off corners wherever required smooth rendering .

Providing and removing scaffolding including cost of all

materials, labour,curing complete as per specifications.

Ground Floor Sqm 694.080 225.00 156168.00

First Floor Sqm 439.040 230.00 100979.20

56 110 15.21 KSRB 15-3-13: Providing 12mm thick cement plaster in single

coat with Cement Mortar 1:3 to Ceiling including rounding off

corners wherever required smooth rendering . Providing and

removing scaffolding including cost of materials, labour,

curing complete as per specifications .Sqm 607.010 167.00 101370.67

RITES Ltd.,



P. No l No

SN Gulbarga SR -

2014-15

Rate Amount

57 110 15.30 Providing rough cement plastering 15mm thick in single coat

with cement mortar 1:4, to brick masonry for base of

dadooing works with sand of approved quality, providing and

removing scaffolding, including cost of materials, labour,

curing complete as per specifications Sqm 31.870 152.00 4844.24

58 111 15.33 KSRB 15-7 - Providing lime rendering for plastering to wait

and ceiling including cost of materials, labour, curing complete

as per specifications.Sqm 2788.760 19.50 54380.82

59 111 15.34 KSRB 15.8.1 : Providing and fixing plaster mesh 100 mm wide

manufactured out of hot dipped galvanised iron of nominal

thickness 0.35mm, with a zinc coating of 120 gms per sqm

width, along route of walls chipped for services, junction

between RCC and brick walls including cost of materials

,labour for fixing, complete as per specifications. (length of

mesh only be measured for payment)m 300.000 28.15 8445.00

60 113 15.51.2 KSRB 15-15.1 : Providing and applying painting in two coats

with plastic emulsion paint of approved brand on wall surface

to give an even approved shade after thoroughly brushing the

surface, free from mortar drops and other foreign matter

including preparing the surface even and sand paper smooth,

cost of all materials , labour, complete as per specifications.

Sqm 2788.760 80.00 223100.80

61 114 15.55 KSRB 15-17.1 : Applying priming coat over new wood surface

and / or wood based surface with whilte lead paint priming

including preparing the surface after thoroughly cleaning oil,

grease, dirt and foreign matter, sand papering and knotting

ready mix paint including cost of materials, labour complete

as per specifications. Sqm 91.200 30.00 2736.00

62 115 15.60.1 KSRB 15-17.6: Providing and applying painting Two coats (

excluding priming coat ) on new wood surface and/or wood

based surface with enamel paint to give an even shade

cleaning the surface of all dirt dust and foreign matter, sand

papering including cost of materials, labour complete as per

specifications. Sqm 57.600 78.00 4492.80

63 31 7.1 KSRB 7.1 : Providing and fixing in position collapsible steel

shutters with single or double leaf with vertical channel

20mmx10mmx2mm braced with flat iron diagonals

20mmx5mm size, with top and bottom rails of T iron sections

of 40x40x6 mm with 38mm dia steel pulleys complete with bolt

and nuts, locking arrangements, stoppers, handles on both

sides with 7.5cms openings at 10 cms. c to c applying a

priming coat of red lead paint. cost of materials, labour, HOM

of machinery complete as per specifications. size of gate

2.4mx1.4m Specification No. KBS 7.7 / 7.12

Sqm 7.200 4311.00 31039.20

RITES Ltd.,



P. No l No

SN Gulbarga SR -

2014-15

Rate Amount

64 31 7.5 KSRB 7.5 : Providing and fixing pull and push type rolling

shutters of approved make out of 18 guage, 75mm wide cold

rolled steel laths of convex corrugation, with side guides and

bottom rail, with interlocking arrangements for steel laths by

means of alternate clips, suspension shaft with High tension

coil type springs two numbers, mounted on specially designed

pipe shaft, with bracket plates, guide channels, ball bearing

arrangements, for inside & outside locking with push & pull

operations complete including pulling hooks, 4Nos. handles

with all fittings and accessories, painted with a coat of red

lead paint (without top cover) cost of materials, labour, HOM

of machinery complete as per specifications. Shutter size

3mx2.8 m Specification No. KBS 7.10 / 7.12

Sqm 21.600 2987.00 64519.20

65 31 7.6 KSRB 7.6 : Providing and fixing top covers made out of 20

guage M.S. sheet over pull and push rolling shutters bent to

shape including cost of red lead primer coat of painting ,


specifications. Specification No. KBS 7.10.6 / 7.12m 9.000 608.00 5472.00

66 117 15.75 KSRB 15-18.3 : Providing and applying enamel metal paint

one coat (excluding priming coat ) on previously painted steel

or other metal surface brushing to give an even shade after

cleaning oil, grease, dirt and other foreign matter, including

cost of materials, labour, complete as per specifications.

Sqm 37.800 47.00 1776.60

TOTAL - Part A - KPWD SR Items 8429177.77

Total Quoted Cost of Part 'A' - KPWD - SR Items based on Percentage Quoted

Percentage above / below / at par of KPWD-SR 2014-15 (Gulbarga Circle) to be indicated for the above items

Percentage in

figure

(+) / (-) / At par

Percentage in

words


Amount in Figure

(Rupees)

Amount in Words

(Rupees)

RITES Ltd.,


1


Rs

PN Item No.

Part B - CPWD SR items

1 72 2.7 Earth work in excavation by mechanical means (Hydraulic excavator) /

manual means over areas (exceeding 30 cm in depth, 1.5 m in width as

well as 10 sqm on plan) including disposal of excavated earth, lead upto

50 m and lift upto 1.5 m, disposed earth to be levelled

and neatly dressed.

2.7.1 Ordinary rock Cum 191.10 244.6 46743.06

2 85 4.2 Providing and laying cement concrete in retaining walls, return walls,

walls (any thickness) including attached pilasters, columns, piers,

abutments, pillars, posts, struts, buttresses, string or lacing courses,

parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,

sunken floor,etc., up to floor five level, excluding the cost of centering,

shuttering and finishing:

4.2.3 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20

mm nominal size) Cum 47.78 6450.00 308181.00

3 88 4.17 Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1

Cement : 3 Coarse sand : 6 graded stone aggregate 20 mm nominal

size) over 75 mm of dry brick ballast 40 mm nominal size well rammed

and consoildated and grouted with fine sand including finishing the top

smoothSqm 84.00 419.30 35221.20

4 150 9.21 Providing and fixing ISI marked flush door shutters conforming to IS:

2202 (Part I) non-decorative type, core of block board construction with

frame of 1st class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face veneers on both

faces of shutters :

151 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws. Sqm 34.80 1909.55 66452.34

5 159 9.96 Providing and fixing Aluminium sliding door bolts ISI marked anodised

(anodic coating not less than grade AC 10 as per IS:1868) transparent

or dyed to required colour or shade with nuts and screws etc., complete.

9.96.1 300 mm X 16 mm Each 45.00 229.65 10334.25

6 159 9.97 Providing and fixing aluminium tower bolts ISI marked anodised (anodic

coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed

to required colour or shade with necessary screws etc. complete:

9.97.2 250 mm x 10 mm Each 45.00 95.25 4286.25

7 160 9.100 Providing and fixing Aluminium handles ISI marked anodised (anodic

coating not less than grade AC 10 as per IS:1868) transparent or dyed

to required colour or shade with necessary screws etc., complete.

9.100.1 125 mm ( for Doors ) Each 60.00 69.80 4188.00

8 160 9.101 Providing and fixing Aluminium hanging floor door stopper ISI marked

anodised (anodic coating not less than grade AC 10 as per IS:1868)

transparent or dyed to required colour or shade with necessary screws

etc., complete.

9.101.1 Single rubber stopper Each 20.00 37.50 750.00

9 177 10.14 Providing and fixing pressed steel door frames conforming to IS: 4351

manufactured from commercial mild steel sheet of 1.60 mm thickness

including hinges, jamb, lock jamb, bead and if required angle threshold

of mild steel angle of section 50x25mm, or base ties of 1.60 mm

pressed mild steel welded or rigidly fixed together by mechanical

means, including M.S. pressed butt hinges, 2.5mm thick with mortar

guards, lock strike-plate and shock absorbers as specified and applying

a coat of approved steel primer after pre-treatment of the surface as

directed by Engineer-in-charge:


Ref. DSR 2014

RITES Ltd.,



Rs

PN Item No.

Ref. DSR 2014

178 10.14.1 Profile B

10.14.1.1 Fixing with adjustable lugs with split end tail to each jambmeter 67.30 377.70 25419.21

10 182 11.5 62 mm thick cement concrete flooring with concrete hardener topping,

under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 20mm nominal size) and top layer

12mm thick cement hardener consisting of mix 1:2 (1 cement hardener

mix : 2 graded stone aggregate, 6mm nominal size) by volume,

hardening compound mixed @ 2 litre per 50 kg of cement or as per

manufacture’s specifications. This includes cost of cement slurry, but

excluding the cost of nosing of steps etc. complete.Sqm 307.32 588.90 180980.75

11 221 13.60 wall painting with acrylic emulsion paint of approved brand and

manufacture yo give even shade

13.60.1 two or more coats on new work Sqm 1133.12 80.50 91216.16

12 346 19.32 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry

brick honey comb shaft with bricks and S.W. drain pipe 100 mm

diameter, 1.8 m long complete as per standard design.

19.32.1 With common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 Nos 2.00 18309.50 36619.00


Add cost index @ 13.33% 108025.15


Total Quoted Cost of Part 'B' - CPWD SR Items based on Percentage Quoted

Percentage in

wordsPlus / Minus / At par

Amount in

Figure

(Rupees)

Amount in

Words

(Rupees)

Percentage above / below / at par of CPWD-SR-2014 of CPWD to be indicated (including Cost Index) for the above items

Percentage in

figure(+) / (-) / At par

RITES Ltd.,


SN Description Unit Qty Rate Amount

Part- C Market Rate Items

1 Providing grooves in plastering on walls 2.50 to

4.00 cms wide and to the required depth as per

design and finished in cement mortar (1:3)

including curing etc., complete m 200.00

2 Supplying and fixing ceramic steel green chalk

board, of size 4 feet X 12 feet, surface sheet

imported from belgium having a thickness of

0.49mm, 8mm thickness of MDF and 0.2mm

thickness of GI sheet at the back covered with

powder coated aluminium frame

Cum 3.00

3 Supply, delivery, installation, testing,

commissioning of vertical centrifugal submersible

pump of 6.5HP capable of pumping 335 lpm

against an approximate total head of 40m from all

causes, including providing 4Cx4sqmm 440V flat

core double sheathed waterproof submersible

cable, Star Delta starter, control panel with dry

run preventer, overload protection and backup

protection and capacitor as required, installed

inside a weather proof kiosk with locking

arrangement of approved design near the

borewell, including making necessary electrical

connections from mains to the starter panel and

from starter panel to the pump. Including

providing and fixing gun metal gate valve and non-

return valve of 50mm n.b on the delivery side of

the pump. Submersible pumps may be of Atlanta/

KSB/ Kirloskar/ CALAMA/ Suguna makes.

No 1

Total - Part C - Market Rate Items

The bidder is required to quote his rates in

figure and words for Part C-Market Rate items



RITES Ltd.,


SN Description of the Item Unit Qty Rate Amount

Part D - Panchayat Raj SR 2012-13

1 Geophysical investigation of site for sinking

borewell for supplying drinking water to the

habitation either through hand pump, MWS or

PWSS by vertical electrical sounding by adopting

Venner or Schlumberger's method, including

reconnaissance survey of Geological formation,

geophysical investigation of existing ground water in

the vicinity indicating the location of site,

recommended depth of casing pipe required to seal

the top unconsolidated formation including an extra

depth of 1m in consolidated formation for proper

seating of casing pipe, depth of drilling required to

cover full depth of aquifer proposed to be tapped,

probable yield and other information required

including transportation of instrument and

accessories to work site, engaging technical

personnel and labour required etc.,

Each BW 1.00 1976.00 1976.00

2 Sinking Bore Well of 165mm dia clear using super

fast hydraulic rig of capacity 250 PSIG & above 900

CMF & above in all strata including over burden

upto 20mtrs fixing of casing pipes, collars and cap

with necessary cutting, threading and welding

including transportation of rig and supporting

vehicle, crew charges and cost of consumables

etc., complete including yield testing at the final

depth with a minimum working of compressor for

one hour (excluding cost of casing pipes, collars,

cap etc.)

0- 50 mtrs RMtr 50.00 321.00 16050.00

50- 100 mtrs RMtr 50.00 420.00 21000.00

100- 150 mtrs RMtr 50.00 467.00 23350.00

150- 200 mtrs RMtr 50.00 494.00 24700.00

3 Yield testing of Borewell at Final depth with a

minimum of 10 hours continuously with the help of

pump testing unit including the cost of

transportation charges, crew charges and cost of

consumables Each BW 1.00 8607.00 8607.00

Part D - Panchayat Raj SR Items 95683.00

Total Quoted Cost of Part 'D' - Panchayat Raj SR 2012-13 Items based on Percentage Quoted

Amount in

Figure (Rupees)

Amount in

Words (Rupees)

Percentage above / below / at par of KPWD-Panchayat Raj SR Gulbarga 2012-13 to be indicated (including Cost

Index) for the above items

Percentage in figure (+) / (-) / At par

Percentage in words Plus / Minus / At par

KPWD

Panchayat Raj

SR Bangalore

2012-13 Item

No. 9.1

9.1.1

KPWD

Panchayat Raj

SR Bangalore

2012-13 Item

No. 9.9

9.1.2

9.1.3

9.1.4


IN

KPWD Panchayat

Raj SR Bangalore

2012-13 Item No.

9.4

RITES Ltd.,


Part A - KPWD SR 2014 - 15

POINT WIRING

Point wiring using Copper wire without switch.

1 2.3 5 Supplying and wiring adopting loop system in

existing PVC Conduit / casing capping using

1100V grade, COPPER conductor flexible

multistrand FRLS PVC insulated, 2x1.5Sq.mm

Cable confirming to the GTP without switch, the

other end of the wires shall be terminated with

sufficient loose length in a wood/PVC round block

complete for each outlet.

GROUP A

a 2.3.1 5 Short point up to 3 Mtr from tapping point to out let

via switch box Point 10 144.00 1440.00

b 2.3.2 5 Medium point above 3 Mtr up to 6 Mtr from

tapping point to out let via switch box Point 32 215.00 6880.00

c 2.3.3 5 Long point above 6 Mtr up to 10 Mtr from tapping


d 2.3.4 6 Two outlet in a row, above 3 Mtr up to 6Mtr from

tapping point to out let via switches Point 22 423.00 9306.00

2 3.5 15 Supplying and flush mounting powder coated /

galvanized metal box suitable for mounting

modular switch plates. The box should be firmly

flush mounted after due groove cutting in

Brick/Stone/C.C wall

a 3.5.1 15 1-3 Way Each 28 91.00 2548.00

b 3.5.2 15 4-5 Way Each 66 98.00 6468.00

c 3.5.3 15 6 Way Each 20 121.00 2420.00

d 3.5.4 15 8 Way Each 13 140.00 1820.00

e 3.5.5 16 10-12 Way Each 12 159.00 1908.00

3 3.6 16 Supplying and fixing superior quality modular

switch mounting polycarbonate plate with

necessary supporting back plate with required

nos. of machine screws, bolts nuts etc., complete

on the existing metal/PVC box.

a 3.6.1 16 1 to 3 Module Each 28 109.00 3052.00

b 3.6.2 16 4 Module Each 66 122.00 8052.00

c 3.6.3 16 6 Module Each 20 173.00 3460.00

d 3.6.4 16 8 Module Each 13 200.00 2600.00

e 3.6.6 16 12 Module Each 12 267.00 3204.00

4 3.7 16 Supplying and fixing of modular switch/

Socket/stepped electronic fan regulator/

dimmer/telephone socket etc on existing modular

switch plate as per IS 3854 and IS 1293

GROUP A

a 3.7.1 16 6 Amps one way. Each 140 63.00 8820.00

b 3.7.3 16 6 Amps 3way socket. Each 40 95.00 3800.00

c 3.7.4 16 Stepped Fan Regulator. Each 24 286.00 6864.00

d 3.7.8 16 6 Amps Bell push Each 2 87.00 174.00

Construction of Govt. ITI at Chincholi in Kalburgi District - Electrical Works


RITES Ltd.,



e 3.7.9 16 32 Amps DP switch Each 60 164.00 9840.00

f 3.7.10 16 6/16 Amps universal socket Each 60 147.00 8820.00

g 3.7.11 16 TV / Telephone socket Each 8 82.00 656.00

h 3.7.12 16 RJ 45 / I.O. outlet Each 12 204.00 2448.00

5 1.12 3 Supplying and Fixing Metal Fan Box with Round

Hook.

No 24 92 2208

1.2 2 Concealed Conduit System

6 Supplying heavy gauge PVC conduit pipe

……mm dia .......mm thick confirming to IS 2509

with suitable size bends, metal/PVC junction

boxes adhesive paste etc., and running before

concreting the slab. The conduit should be tied to

the reinforcement rods by using binding wires and

unused ways of junction boxes and pipe ends

should be covered using PVC end enclosures. run

with 18SWG GI fish wire wherever necessary

a 1.2.1 2 19/20 mm dia 2mm thick Mtr 540 43.00 23220.00

b 1.2.2 2 25 mm dia 2mm thick Mtr 2200 57.00 125400.00

c 1.2.3 2 32 mm dia 2.5mm thick Mtr 100 90.00 9000.00

Groove Cutting

7 1.3 2 Supplying heavy gauge PVC Conduit Pipe ----- dia

-- mm thick with suitable size bends, metal

junction boxes adhesive paste etc., by groove

cutting in the wall and fixing by bracing U or J

hooks and cement Plastering up to the wall

surface and run with 18 SWG GI fish wire run

throughout the conduit wherever necessary.

a 1.3.1 2 19/20mm dia 2mm thick Mtr 160 56.00 8960.00

b 1.3.2 2 25mm dia 2mm thick Mtr 360 58.00 20880.00

c 1.3.3 2 32mm dia 2.5mm thick Mtr 100 88.00 8800.00

8 1.8 3 Supplying and fixing of PVC casing and capping

on the wall or ceiling using necessary materials

like bends, screws at an interval of 300mm …. Etc

as required.

a 1.8.2 3 25mm Mtr 160 26.00 4160.00

b 1.8.4 3 38mm Mtr 160 39.00 6240.00

c 1.8.5 3 50mm Mtr 160 43.00 6880.00

9 2.5 6 Wiring for lighting/power circuit using one of

FRLS PVC insulated 1100v grade, multistrand

Copper with low conductor resistance single

core wire in open or concealed system of wiring

with specified IS-694:1990 & confirming to

GTP of GROUP-A

a 2.5.2 6 1.5 sqmm Mtr 2300 18.60 42780.00

b 2.5.3 6 2.5 sqmm Mtr 1800 29.20 52560.00

c 2.5.4 6 4 sqmm Mtr 3200 42.10 134720.00

d 2.5.5 6 6 sqmm Mtr 350 63.80 22330.00

e 2.5.6 6 10 sqmm Mtr 680 108.00 73440.00

RITES Ltd.,



DISTRIBUTION BOARDS

10 6.17 47 Supplying and fixing regular MCB distribution

boards on wall / wood board / flush mounting

using required clamps, bolts, nuts etc., with

provision for fixing suitable type capacity MCB's

single phase / 3 phase / single door with powder

coated painting. Made out of 14 SWG MS

enclosure.

I - Single Door

a 6.17.1 47 4 way SP&N Each 14 706.00 9884.00

( Only for Work shops )

II - Double Door

b 6.17.7 47 4 way TP&N Each 2 2399.00 4798.00

c 6.17.6 47 12 way SP & N Each 2 1622.00 3244.00

11 6.15 46 Supplying and fixing regular MCCB distribution

Panel confirming to IS 8828, on wall / wood board

/ flush mounting using required clamps, bolts, nuts

etc., with provision for fixing of suitable type

capacity MCCB's as an incomer for 3 phase

Double door with necessary bus bar completely

wired to use on 440 Volts 3 phase 4 wire powder

coated painting etc., complete with a provision for

fixing of single / three phase suitable capacity

MCCB / MCB's as outgoings confirming to IS

8828.

a 6.15.2 46 8 way Each 3 9095.00 27285.00

12 6.16 47 Supplying and fixing miniature circuit breakers on

existing MCB distribution boards using necessary

fixing materials and 'C' Type curve , indicator a 6.16.1 5-32 Amps SP Each 80 418 33440.00

b 6.16.3 5-32 Amps DP Each 2 849 1698.00

c 6.16.5 5-32 Amps TPN Each 14 1547 21658.00

d 6.16.6 40-63 Amps TPN Each 2 1936 3872.00

13 6.18 47 Supplying, fixing and wiring Earth Leakage

Miniature Circuit Breaker [ELMCB] 240/450V up

to 300mA sensitivity on existing wood/panel

board.

a 6.18.2 47 32-40 Amps 2 pole Each 2 2623.00 5246.00

b 6.18.3 47 32-40 Amps 4 pole Each 2 2936.00 5872.00

14 6.43 50 Supplying and fixing of Metal Socket set of 2pole

and earth plugs and socket for incorporating SP

and TP MCB (Without MCB ). The entire plug and

socket shall b mounted in a Thermoplastic /

powder coated metal box & wired Completely.

A) SP & N

a 6.43.2 b) 20 Amps Each 4 918.00 3672.00

SUPPLY OF FITTING

15 4.7 20 Supplying Box Type Suitable for 28 W T5 Single /

Twin lamp & suspension mounted luminaire &

optical reflector,prewired with HF Electronic

Ballast,push fit type lamp holders & main

connectors. Channel cover shall be made of

CRCA MS Sheet and finishing is done with stove

enamelled white with end caps made of

engineering Plastic.

RITES Ltd.,



Group - A

a 4.7.1 1 X 4'-28 Watts Each 66 990.00 65340.00

b 4.7.2 2 X 4'-28 Watts Each 6 1680.00 10080.00

16 4.23 24 Supplying CFL mirror light fitting with 1x11W

CFL lamp, choke, Perspex cover and completely

wired for use on 230V 50Hz AC supply.

Each 2 648.00 1296.00

17 4.17 22 Supplying High pressure Metal halide street

light luminary suitable for use with high pressure

metal halide lamp with integrated control gear &

grey color powder coated. The fitting shall be non

corrosive pressure die cast aluminum housing

with high purity anodized aluminium reflector with

EPDM Gaskets suitable for Outer Dia of pole

40mm - 60mm. Cable Entry through a cable gland

with toggle clips. IP65 Protection for both optical &

Electrical Compartment. Bottom cover may be

with Poly carbonate/tempered/ toughened glass.

Luminaire efficiency should be >60 % & ambient

temperature > 35 deg C. High Intensity Discharge

Electro Magnetic Ballast with Copper winding of

Orthocyclic winding coil. Class H insulated dual

coated copper wire. Compliance to IEC 61347-2-9

Safety & IEC 60923 - Performance. Winding

Temperature for HID Ballast Tw = 130 deg C &

temperature rise ?T = 70 deg C. Luminaire shall

be suitable to operate on 230/250 Volts 50 Hz AC

supply finish including wiring, ignitor, condenser.

SS Toggles for opening front hingeable glass.

a 4.17.2 23 150Watts Each 1 6300 6300.00

18 9.3 78 Supplying capacitor type ceiling fan complete

with down rod blades, shackle, canopies etc., for

operation on 230 volts, 50 cycles. Single phase

AC supply conforming to ISS-374-1979 and with

double ball bearing system.

9.3.1 48" Sweep (1200mm)

a 9.3.1.1 78 Regular model Each 24 2376.00 57024.00

19 9.2 78 Supplying of 1440rpm heavy duty exhaust fan

with bracket blades suitable to operate on 230V

50Hz, AC Supply complete.

a 9.2.1 78 12" Sweep (300mm) Each 10 3654.00 36540.00

20 4.2 20 Supplying and fixing PBBC/Bakelite straight or

slant batten holder and wiring with 60 W / 230

volts lamps. Each 10 88.00 880.00

21 16.1 104 Supplying and fixing one of 230 volts bell or

buzzer and a flush type bell push with gang box

fixed on necessary wooden or rawl plugs using NF

screws. Each 2 145 290.00

RITES Ltd.,



FIXING CHARGES

22.0 17.2 108 Supplying and Fixing........mm dia class A GI pipe

bracket up to 2.7 meters long terminated with a

reducing collar of 40x25mm to which extra pipe of

175mm length is fixed for fixing MV/SV/MH/FTL

street light fitting of all capacities on

rail/RCC/wall/tubular pole, using suitable clamps,

bolts ,nuts and wiring using suitable capacity wires

etc complete.

a 17.2.2 108 Using 32mm dia G.I.pipe Each 1 1140.00 1140.00

23 17.7 108 Fixing all types and all capacities of fluorescent /

false ceiling / spot light / CFL / LED fittings

indoor on the wall / ceiling/ rafters / girders

using 23/0.0076” twin twisted PVC insulated

wires, required Nos of round blocks and clamps

a 17.7.1 108 On wall / ceiling / Rafter / Girders Each 74 98.00 7252.00

24 17.8 109 Fixing a ceiling / Wall mounting fan of all

capacities and all types to the existing 'S' hook

with fan regulator to the existing board together

with supplying and fixing 5 amps. ceiling rose,

necessary length of 23 / 0.0076 inch PVC

insulated twin twisted copper wire and wiring.

Each 24 139.00 3336.00

25 17.12 109 Fixing one exhaust fan in the nitch already left in

the wall with bolts and nuts and 5 amps. Ceiling

rose with sufficient length of 23 / 0.0076 inch PVC

insulated twin core wire. Each 10 412 4120.00

26 17.5 108 Fixing halogen/metal hallide / SVL / IL / LED

floodlight fitting over existing pole / wall ceiling

including clamps, bolts, nuts and wiring using

suitable capacity wires. Each 1 176.00 176.00

27 11.1 85 Supplying and drawing UTP-CAT 6E LAN cable.

Mt. 180 23.00 4140.00

28 11.2 85 Supplying and drawing PVC flexible one pair

telephone unarmoured tinned copper cable.

a 11.2.2 85 2 Pair mtr 132 13 1716.00

29 1.4 2 Supplying and fixing sheet metal box made out of

18 SWG sheet metal with necessary holes for

cable/conduit entry as required with one coat of

primer of approved make etc.

a 1.4.7 2 200 x 200 x 65 mm Each 4 157.00 628.00

30 7.4 55 Supplying of 1.1 KV LT UG cable having

aluminium conductor PVC insulated, extruded

inner sheated , galvanized , steel strip (except 2C

X 10 Sq.mm wire armoured) confirming to IS -

3975 : 1990 (No. of strip indicated in GTP) &

extruded PVC outer sheated armoured cable with

specified IS - 1554 Part - 1:1988 & confirming to

GTP of Group - A.

7.4.4 55 4 core 16 sqmm Mtr 200 140.40 28080.00

RITES Ltd.,



31 7.8 61 Labour charges for laying of 1.1 KV class UG

cable in existing trench GI pipe / stoneware pipe /

on wall / on pole as required.

In existing trench / duct.

7.8.1 61 6 sqmm to 16 sqmm Mtr 200 10.80 2160.00

.

32 7.9 61 Digging of trench of 0.6m deep X 0.50 mtr wide

refilling the trench to the required ground level and

consolidating etc., complete. (As per Civil SR

KSRB I - 2, P - 7)

7.9.2 62 In soil (hard) Mtr 100 106.00 10600.00

33 7.10 62 Providing and filling sand in excavated trench to

cover already laid UG cable to adepth of 150 mm

all - round the cable. Mtr 100 103.00 10300.00

34 7.14 62 Supplying and fixing of heavy duty cable glands

suitable for UG cable of 1.1 KV class (metal only)

7.14.2 62 25 mm dia Each 6 86.00 516.00

35 7.21 64 Supplying tinned copper lugs and crimping and

wiring to terminal point for wire of the following

sizes.

7.21.6 64 16 sqmm Each 24 11.31 271.44

EARTHING

36 7.2 55 Supplying fixing and wiring earth electrode for

grounding of lifts, transformers, DG sets etc.

using 40mm dia 2.9mm thick 2.5 mtr long GI pipe

with GI funnel with mesh and suitable size reducer

fixed on the top of the earth electrode. The funnel

should be enclosed in a CC chamber of

400x400x400mm with a cast iron cover. The earth

electrode shall have staggered holes of 12mm dia

and the electrode should be covered 150mm

alround with alternate layers of salt and charcoal

from the bottom of the CC chamber. The

connection from the electrode is to be established

through GI strip using GI bolts and nuts.

Each 3 4317.00 12951.00

37 7.3 55 Supplying and running of GI/Copper strips for

grounding connections, using necessary fixing

materials as required.

GI strip

a 7.3.1 55 25 x 3 mm Mtr 60 77.00 4620.00

c 7.3.10 55 600 x 600 x 3 mm copper plate Each 1 7148.00 7148.00

38 7.22 64 Supplying and running GI/Copper conductor for

grounding and (along with other wires in conduit

system of wiring) using necessary suitable size

clamps, nails, guttas/spacers etc.,

Copper Wire.

b 7.22.6 64 8 SWG Mtr 60 107.70 6462.00

RITES Ltd.,



39 7.12 62 Supplying and fixing of class A (medium duty) GI

pipe of wall thickness not less than 3.25mm on

pole/wall/drain crossing with necessary clamping

arrangements for UG cable of 1.1 KV.

a 7.12.2 62 50mm Mtr 20 391.00 7820.00

Part A - KPWD SR Items - Electrical works 1064045.44

Total Quoted Cost of Electrical Items based on Percentage Quoted

Amount in Figure

(Rupees)

Amount in Words

(Rupees)

Percentage in

words


Percentage above / below / at par of KPWD-SR 2014-15 for Electrical Works to be indicated for all the above

Percentage in

figure

(+) / (-) / At par

RITES Ltd.,


SN Description of Work Unit Qty Rate Amount

Part B - Market Rate Items

Sub MV Panel

1 Supply, installation, testing and commissioning of LT

Sub MV Panel fabricated out of 16 SWG sheet steel

metal floor mounting type with all normal practice like

derusting, degreasing, phosphating, powder coated to

the approved make as per specification, comprisiing of

the following:-

Incomer

I. 125 A 3P MCCB 35 KA breaking capacity - 1No.

ii. 250A Al Bus bar (RYBN)

iii. RYB phase indication lamps - 1set

iv.0-500 V Voltmeter with selector switch -1no

v.0 - 300 A Ammeter With selector switch-1no

Outgoing

iii. 63 A 4Pole 16 KA MCCB - 12 nos.

iii. 40 A 4Pole MCB - 3 nos. Nos 1.00

2 Supplying and fixing Moulded Case Circuit Breaker

(MCCB) over the existing wood / panel board using

necessary screws, bolts, nuts and wiring complete.

Protection of Overload and Short circuit with thermal

Magnetic / Micro processor release and Earth Fault as

per IS - 13947. (Icu = Ics)

63 Amps 16 KA (Three Pole) Each 4.00

Part B - Market rate Items - Electrical works

The bidder is required to quote his rates in figure

and words for Part B-Non SR items of Electrical

works

Construction of Govt. ITI at Chincholi in Kalburgi District - Electrical Works


RITES Ltd.,

For and on behal of DET 49 Signature of the Bidder

commissioner dept. of employment and … · morth specification no. 201 ha 0.150 42114.00 6317.10 2...

Documents