Accessories

Part names Preparation

Features

Polishing Procedure

Others

● Open/close of the lever is linked with the motor When the lever is pushed, the polished sample will be

ejected to the polished sample receptacle.

● Sample scatter-proof function To avoid scattering of the sample, the polishing disk will

not be rotated if the cover is fully opened.

● Transparent bran receptacle The timing for discarding the removed bran can be seen

at a glance.

● Motor overload prevention If excessive force is applied to the motor and there is a

risk of the motor coil being damaged, the power turns off automatically.

① Properly attach the bran receptacle to the main unit. Fully insert the bran receptacle to the outlet of the

removed bran. Note that if the case is not properly attached, the bran will be scattered during polishing.

① Take a spoonful of sample with the supplied spoon.* A spoonful of rice measured with the supplied spoon is approxi-

mately 10 g.

② Set the sample on the polishing disk of the Pearlest and close the cover. Then, lock the latch.

* If bran or dust is left, the cover may not be closed. Before start polishing, clean the unit and fully close the cover.

③ Turn the power ON to start polishing. The polishing time differs depending on the samples or moisture

content. Set the polishing time referring to the following.

Samples A guide for polishing time

Short rice 30 to 40 sec.

Long rice 40 to 60 sec.

Barley 180 to 240 sec.

* Many broken particles may be generated depending on the sample.* For barley, optional parts for barley polishing are required. Before

polishing, refer to the back page and assemble the parts correctly.

④ Push the lever while the cover is closed.* If the sample is left in the polishing unit, the clatter may be heard.

Push the lever until the sound is stopped.

⑤ The polished sample is ejected to the polished sample receptacle.

⑥ The motor stop when the power is turned off.

⑦ Open the cover, and take out the polished sample receptacle.

* The polished sample receptacle can be used as a strainer. If bran or dust is left on the tray, clean the tray before use.

Pallet(TP-3000-A-01)

Brush(TP-3000-A-02)

AC adapter(TP-3000-A-05)

Accessory case(TP-3000-A-06)

Paint brush(TP-3000-A-03)

Spoon(Rice : approx. 10 g/spoon)

(TP-3000-A-04)

<Cleaning> After a few times of polishing, removed bran or dust may

accumulate around the rubber disc or polishing disk. Clean the polishing unit using the pallet or paint brush.

<Storage> When storing the instrument, remove the polishing disk,

rubber ring, and rubber disc. Clean the inside of the bran receptacle. Store the

instrument in a place where the direct sunlight is avoided under dry conditions.

<Specifications> Power

Input: 100-240 V AC (50/60Hz), 1.4 A MAX Output: 24 V DC, 2.71 A Dimensions: 110 (W) x 152 (D) x 176 (H) Mass: approximately 1.7 kg

Compact Grain Polisher PearlestTP-3000

Operating Manual

Thank you for purchasing our grain polisher.The Compact Grain Polisher Pearlest can polish a small amount of rice extracted for the purpose of testing in a short time. Since the rubber plate is used, capability of bran removal is excellent, and the grains are well finished. The polished grains can be ejected only by pushing the motor-linked lever. The Pearlest can also be used for inspecting condition and mixing degree of spotted rice influenced by pentatomid, burnt, cracked, colored, nonglutinous, or glutinous rice. Before using this instrument, thoroughly read this operating manual, and use it properly.

Bran receptacle(TP-3000-R-04)

Power switch

Cover

Latch

Lever(TP-3000-R-06)

Rubber disc(TP-3000-R-05)

Polished sample receptacle(TP-3000-R-01)

Rubber ring(TP-3000-R-02)

Polishing disk(TP-3000-R-03)

Status lampTimer jackDC power inlet

② Make sure that the cover is closed, and the power is turned off. When the AC adapter is connected to the outlet, the status lamp will light up.

(1) Push the bottom part of the bran receptacle toward the main unit.

(2) Pull the entire case from the top.

<How to remove>

* Do not put the fingers into the outlet of the removed bran. The drive unit can catch fingers and severely injure them.

● Status lamp<On> The device is ready to be used.<Off> For safety, the sensor is activated and the device is

stopped. Close the cover while the AC adapter is connected to the

outlet. When the POWER switch is turned off, the status lamp will be lit to indicate the device is ready to be used.

<Blink> Due to over-current, the device is stopped protecting the motor.

If the lamp is blinking while the AC adapter is connected to the outlet, disconnect the plug once, and reconnect. If blinking or off state continues, contact Kett.

* Do not use other than the specified AC adapter. Otherwise, it may cause malfunction, fire, or electric shock, etc.

Pearlest Timer TZ-910 (option)Operating Manual

Parts for Barley Polishing (option)Operating Manual

① Disassemble the rice polishing parts using the supplied pallet.

(washer, polishing disk, rubber ring, rubber disc)

② Set the polishing time using the [+]/[-] key. Long pless of the key will change the value swiftly.

③ Take a spoonful of sample with the supplied spoon.

④ Set the sample on the polishing disk of the Pearlest and close the cover. Then, lock the latch.

* If bran or dust is left, the cover may not be closed. Before start polishing, clean the unit and fully close the cover.

⑤ Pless the [START/STOP] key. The set time for polishing will start counting down in

steps of 1 second.

⑦ Push the lever while the cover of the Pearlest is closed.

* If the sample is left in the polishing unit, the clatter may be heard. Push the lever until the sound is stopped.

⑧ The polished sample will be ejected to the polished sample receptacle.

⑨ When the motor is stopped, open the cover, and take out the polished sample receptacle.

⑩ Pless the [ON/OFF] key to turn off the power.

⑥ Polishing ends at 0 second. The display restores the preset time.

Beeps

① Connect the Pearlest and the timer using the dedicated cable.

② Connect the AC adapter to the Pearlest DC power inlet.

② Assemble the parts for polishing the barley. (metal ring, metal disk (a), washer for barley, metal disk (b))

① Pless the [ON/OFF] key. The previously set time will be displayed.

Accessories

Accessories

How to Assemble

How to Connect

Directions (The power of the Pearlest is always OFF.)

The polishing time can be set between 0 second and 59 minutes 59 seconds.Plessing the [ON/OFF] key will start and end the polishing in the preset time.

By replacing the polishing parts for rice to the barley, barley polishing will become available. Also, the parts can be used for rice suitable for brewing sake.

* In order to avoid loosening of the parts, firmly fix with the supplied pallet.

Disc fixing screw(TP-3000-O-07)

Hex wrench(TP-3000-O-06)

Fixing nut

Washer

Polishing disk

Rubber ring

Disc fixing screw

Rubber disc

Fixing nut

Washer for barley

Metal disk (a)

Metal ring

Metal disk (b)Disc fixing screw

CautionsWhen using the Pearlest Timer TZ-910, it is required to set the power of the Compact Grain Polisher Pearlest TP-3000 always OFF. If the power in ON, the timer is disabled.

The power has to be OFF.If it is ON, the Pearlest timer cannot be used.

Pearlest timer(TP-3000-O-01)

Dedicated cable(TP-3000-O-02)

Washer for barley* thicker than rice

(TP-3000-O-08)

Metal disk (a)(TP-3000-O-03)

Metal Ring(TP-3000-O-05)

Metal disk (b)(TP-3000-O-04)

<Specifications> External Dimensions & Weight: 128 (W) x 98 (D) x 56 (H)

mm, 0.2kg

060238-01

* Do not use other than the specified AC adapter. Other-wise, it may cause malfunction, fire, or electric shock, etc.

Example) Polishing time: 1 min. 10 sec.

Beeps shortly twice

Beeps shortly twice

* When the [START/STOP] key is plessed during polish-ing, the display restores the preset time.

Beeps shortly