congratulations - quik spray · page 2 1800 645 688 congratulations_____ quik corp would like to...

1800 645 688

www.quikcorp.com.au

CONGRATULATIONS____________________

QUIK CORP would like to thank you for investing in a remote control

retractable hose reel spraying system.

Our units are manufactured to the highest standard of quality to give our

customers the best product and service possible.

This manual should be considered a permanent part of your Quik Corp Unit and

should remain with it at all times.

This manual covers the Operation and Maintenance of Models 5SCE and 5TCE.

IMPORTANT_________________________________

READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE

ATTEMPTING TO OPERATE THE UNIT.

No part of this manual may be reproduced without written permission.

All information in this manual is based on the latest product information

available at the time of printing.

PLEASE KEEP THIS MANUAL WITH YOUR QUIK SPRAY

SPRAYING SYSTEM AT ALL TIMES FOR QUICK

INFORMATION & TECHNICAL REFERENCE!

1800 645 688

www.quikcorp.com.au

Unpacking and Set up -------------------------------------------------------------------------4

Unit Photos and Diagrams -------------------------------------------------------------------5

Pre Operation Check --------------------------------------------------------------------------9

Basic Operation and Hints ------------------------------------------------------------------10

Maintenance -----------------------------------------------------------------------------------11

Trouble Shooting Guide Pumps -----------------------------------------------------------14

Turbo 400 Break Down----------------------------------------------------------------------18

Karen Pressure Controller Break Down-------------------------------------------------19

Bertolini PA430 Pump Breakdown--------------------------------------------------------20

Trouble Shooting Guide Radios -----------------------------------------------------------21

Machine Specifications ----------------------------------------------------------------------23

Warranty Policy ------------------------------------------------------------------------------24

Warranty Registration Form --------------------------------------------------------------28

1800 645 688

www.quikcorp.com.au

Unpacking__________________________________________

When unpacking your new Quik Corp Quik Spray unit check thoroughly for any

transport damage, and that all parts, accessories, and extra options ordered have

been included.

1. Aerial/s

2. Transmitter/s

3. Instruction Manuals (Honda, Bertolini, Quik Corp)

4. All accessories as ordered

Warning: READ THIS MANUAL CAREFULLY AND IN ITS

ENTIRETY BEFORE USING THIS UNIT.

Set Up______________________________________________

1. Mount the machine securely by bolting through both mounting lugs located at

the front middle of the two fork lift points. Run a strap through the back upper

tank eye bolts and secure to both sides of the vehicle. THE UPPER TANK

EYEBOLTS ARE NOT TO BE USED TO LIFT THE MACHINE WITH.

LIFTING THE MACHINE IN THIS WAY WILL VOID THE TANK

WARRANTY! Lifting the machine should only be done using the fork lift

channels built into the front machine framework and when the tank is empty of

fluid. Ensure minimum of 50mm clearance from all sides to prevent damage.

2. Fit aerial/s to the aerial mounting base/s.

CAUTION VERY IMPORTANT: Do not over-tighten the aerial/s to aerial

base/s. Finger tight and a nip more is all they need to be attached properly. Any

more than this will cause the coax cable to break in the solder cap of the aerial

base/s severing the connection to the aerial. The result of this will be a radio

range of only 20-30 meters rendering the aerial/s incapable of receiving a signal.

1800 645 688

www.quikcorp.com.au

System Overview - Fig. 1______________________________

Two way ball

valve tank shut

off and filter

assembly. Clean

filter daily.

Pump oil level

sight glass.

Bertolini

PA430 pump

used SAE 30

weight oil.

Chain drive

gearbox safety

guard.

Honda GX160

5.5 HP motor.

Reel friction

break lever. Set

to complete lock

for driving.

Adjust the

desired amount

of drag needed to

prevent run on

when spraying.

Two way ball

valves to turn

on or off

chemical flow

to the reels.

Main electrical

control panel

with on/off

power switch,

motor remote

start, tachometer

and manual

override reel

retraction

buttons.

Aerial base

location. One

for each reel.

1800 645 688

www.quikcorp.com.au

Control Centre – Fig. 2________________________________

Reel break locking

ratchet lever with

anti-roll on drag

function.

Black ball valve lever

for on/off chemical

flow to reel. Blue

bypass/press lever for

Bertolini PA 430

pump

40 bar pressure gauge

and pump pressure

controller adjustment

knob.

27 MHz radio

receiver box.

Green 40 bar safety

valve.

Power on indicator

light, on/off power

switch, Honda

remote start button,

and Honda engine

tachometer.

Left and right manual

reel retraction

buttons.

1800 645 688

www.quikcorp.com.au

27.145 & 27.195 Radio Receiver Boards and Transmitters J.G. 3/13

Left reel relay and

white relay

operational light

Terminals from left to

right: Left antenna

internal coax, earth, 12V

positive power in, power

out to left reel clutch,

right antenna internal

coax, power out to right

reel clutch

27.145 MHz left reel

transmitter PN

4440000 Dipswitch

toggles need to match

the bottom left 27.145

MHz receiver board

27.195 MHz receiver board for the right reel.

PN 4431000 The set of blue and white

dipswitch toggles need to match the 27.195

MHz transmitter for the right reel to operate.

27.145 MHz receiver board for the left reel

(directly underneath the top receiver board) PN

4430000 The blue and white dipswitch toggles

need to match the corresponding set in the

27.145 MHz transmitter for remote operation

Blue operational light for

27.195 MHz right receiver

board and operational light

for the red mother board.

The left 27.145 MHz blue

operational light is directly

under the top board in the

same location

27.195 MHz right

Transmitter PN

4441000 The blue and

white dipswitch toggles

need to match the 27.195

MHz receiver board for

remote operation

This remote

control module

is used on

Quik Corp

Models:

9TBE

9TDE

5TCE

3PL9TDE

10TBE

5SCE

5TCE

1800 645 688

www.quikcorp.com.au

Tank drain ball valve location__________________________

Radio transmitter.

Tip: Always use a high quality

9 volt battery to power your

radio transmitter. Replace the 9

volt battery at least every 3

months and more often with

continual use. As the battery

voltage drops the effective

radio range will drop

accordingly.

Tank drain ball valve. The

handle for the ball valve is

located in the machine kit bag

that includes the machine manual

and hand held transmitter/s.

Only install the handle when

needing to drain the tank for

safety.

1800 645 688

www.quikcorp.com.au

Pre-Operation Check_________________________________

1. Spray guns connected and water tight

2. Fuel in motor (unleaded)

3. Correct oil level in pump (pump manual)

4. Correct oil level in motor (motor manual)

5. Controller 2 way ball valves in the off position

6. Pressure lever in bypass position

7. All safety guards and shields in place

8. All nuts, bolts, and screws are in place and tight

9. Radio on/off switch in the off position.

10. Make sure that the unit is in an open space (exhaust gas is poisonous)

11. All maintenance schedules have been completed

12. Start engine (see engine manual)

13. Adjust engine revs to approximately 2400 rpm or ¾ revs.

CAUTION: Children, livestock, and pets must be kept away from the

area of operation.

CAUTION: Know how to stop the engine quickly.

CAUTION: Make sure the fuel cap is closed securely.

Safety First_________________________________________

IMPORTANT: Heed all these warnings as failure to do so may

result in serious injury, permanent injury or death.

1. DO NOT let any person near the unit while it is operating.

2. DO NOT start the unit until you have read this manual carefully.

3. DO NOT start motor with pressure lever in the “press position”

4. DO NOT pull the hose out too fast as the reel may run on, causing the hose to

become entangled.

5. DO NOT alter the equipment in any manner. If repairs are necessary use

only genuine factory repair parts.

6. DO NOT leave the unit running unattended at any time.

7. DO NOT operate the unit if there are any leaks from hoses, fittings, ECT.

Fluids which are under high pressure can penetrate the skin.

8. DO NOT operate near power lines, as contact could result in electrocution.

9. DO NOT refuel the engine until it has stopped and, if any fuel is spilled, make

sure the area is dry before starting the engine.

1800 645 688

www.quikcorp.com.au

Warning: Improperly maintaining this unit, or failing to

correct a problem before operating, could cause a

malfunction in which serious damage to the unit or serious

personal injury could occur.

Always perform a pre-operation inspection before each

operation and correct any problems.

Basic Operation______________________________________

1. Ensure pre-operation check is complete.

2. Fill tank to desired level. If optional fast filler is fitted refer to page 12.

CAUTION: Never fill tank with the lid closed.

3. Turn fuel valve to the on position and run engine for 2-3 minutes to prime

the pump.

4. With the pump primed turn lever (fig. 2) to the “press” position.

5. Adjust working pressure with the pressure knob (fig. 2). (Clockwise for more

pressure counter-clockwise for less).

6. Open the 2 way ball valve to reel/s (fig. 2).

7. Turn radio on/off power switch to the “on” position and carry transmitter/s

with operator/s. Make sure if using a twin reel system each operator is

carrying the correct transmitter to their corresponding reel.

8. Quik Spray reels will free-wheel out to the desired distance.

CAUTION: Do not pull the hose out too fast, as the reel may run on causing

the hose to become entangled.

9. When ready press the button on the transmitter to retract the hose back onto

the unit reel.

CAUTION: Be ready to release the transmitter button when approaching the

reel/s as personal injury or damage to the unit may result.

10. After use flush unit out with Quik Flush tank/pump cleaner according to

the directions on the bottle. (This will clean and lubricate and extend the life

of the tank, pump, hoses, diaphragms, o-rings and seals.

11. Rinse tank with clean water through the gun nozzle until foaming reduces.

12. Turn radio on/off switch to the off position to prevent 12 volt battery

discharge. NOTE: It is recommended that the 12 volt battery be connected

to an automatic battery charger when the unit is not in use. This will help

avoid any damage to the 12 volt battery and help keep the unit working

optimally.

13. Turn fuel valve to the “off” position.

For winter storage, if freezing conditions are expected, empty pump

completely and flush with a mixture of water and antifreeze to

prevent unrepairable damage to your unit.

1800 645 688

www.quikcorp.com.au

Maintenance______________________________________

For engine and pump maintenance refer to their manuals

Daily Maintenance

1. Clean inline filter (fig. 1).

2. Check oil level in pump.

3. Check all drive belts for tension and wear.

4. Check oil level in engine.

5. Check all hoses and fittings for leaks.

20 Hours

1. Check water in the 12 volt battery (if fitted).

2. Recharge 12 volt battery if necessary.

3. Replace 9 volt battery in transmitter/s if radio range has decreased.

4. Check all belts and adjust belt tensioning bolts if needed.

5. Check aerials and bases.

6. Wash off any salt.

7. Check all chain drives (refer to chain maintenance schedule page 11).

8. Flush unit with Quik Flush according to directions on bottle.

Yearly

1. Check all chain drives (refer to chain maintenance schedule page 11).

2. Overhaul pump according to pump manual.

3. Inspect pressure controller valve and diaphragm, replace if necessary.

4. Inspect all bolts, nuts, and fittings. Tighten or replace if necessary.

5. Check reel break belt and adjust the spring tension if necessary.

6. Make sure all safety guards and decals are in place and functional.

7. Replace 9 volt battery in transmitter/s.

8. Inspect wiring loom for damage.

9. Inspect radio receiver box lid seal and replace if necessary.

10. Change engine oil according to engine manual.

11. Test 12 volt battery voltage output. Ensure it is close to 12.5 volts for

optimal radio receiver performance.

NOTE: The working range of Quik Spray Radio Transmitters is affected by

the many factors that typically affect all 27 MHz radio transmissions. These

include 12 volt battery voltage output, 9 volt battery voltage output, operating

in the vicinity of high tension power lines, buildings and other obstructions,

other radio transmitters, and certain atmospheric conditions. A range of 200

meters or more can be achieved under ideal conditions.

1800 645 688

www.quikcorp.com.au

Chain and Sprocket Maintenance Schedule_______________

Chain maintenance for all chain sizes should be lubricated every 2 - 4 months as

needed and checked for tension and wear and replaced when indicated.

40-1 Chain (Standard clutch drive chain on all fully integrated Quik Spray

systems)

Lubricate with WD-40 or similar spray lubrication and remove run off.

Check tension. 10mm-20mm play in the chain is the accepted range. If the

acceptable range is not achievable due to chain stretch, or wear then the 40-1

chain must be replaced with the 40-1 chain con link which attaches one end of

the chain to the other thus forming the loop.

Also check for chain wear and sprocket wear. Replace all sprockets and chain

when wear is more than 20%.

1800 645 688

www.quikcorp.com.au

Optional Equipment________________________________

1. Aerial springs.

2. T-400 spray gun.

2. T-500 spray gun with pressure gauge.

4. Boomless jet with mounting bracket

5. Anabranch liquid handling system for chemical transfer

6. Quik Flush pump and tank wash concentrate

7. Quik Spray belts for pulling the hose out by using your waist.

8. Tank fitted Venturi style “Fast-Filler” system

9. Floating filter and 7m of suction hose for use with Venturi.

10. 12 volt low pressure boom kit with in cab control.

11. Projecta 12 Volt automatic battery charge and maintain system. 1600 mA.

Filling Tank with optional Quik Spray “Fast-Filler”_____

1. Connect suction hose to floating filter and tank mounted “Fast-Filler”

2. Place floating filter into water supply

3. Start engine and prime pump. (If the tank is completely empty add a

bucket of water to the tank to facilitate pump priming).

4. Remove the tank lid and turn on the 2 way ball valve from the pressure

controller that runs to the “Fast-Filler”

5. When the tank has been filled, remove the suction hose from the water

supply while the pump is still running to avoid chemical back flow into

the supply.

6. Turn off 2 way ball valve running from the pressure controller to the

“Fast-Filler” and proceed with Basic Operation Instructions page 12.

This blue hose runs from the Venturi

Fast Filler to the Sting Pressure

Controller and two way ball valve

which turns the Venturi on or off.

Venture Fast Filler. 7 meter Suction

hose with floating filter attached

screws on to Venturi Fast Filler here

for filling from creeks or dams.

1800 645 688

www.quikcorp.com.au

Troubleshooting for Pumps and Pressure Controller____

Problem Probable Cause Remedy Pump does If good flow is being achieved

not deliver from by-pass back to the tank.

pressure.

1. Sting Pressure regulator not 1. Set the lever to press

set for pressure. And adjust the knob.

(Fig 2)

2. Damaged or worn seat or 2. Replace with Sting

spring in pressure regulator. repair kit or new

spring.

3. Sticking pressure regulator 3. Remove slide and

slide. lubricate with

marine grease.

4. Spray nozzle/s worn, missing, 4. Replace spray

or exceeding pump capacity. nozzle/s with correct

size.

If irregular flow from by-pass

to tank.

1. One or more of the pump 1. Clean or replace

valves not seating. valves.

2. Sucking air through the 2. Examine and repair.

suction line, suction fittings,

or filter.

3. Air has not been entirely 3. Run pump in the

evacuated from the pump. by-pass mode until

all air is evacuated.

4. Blocked suction filter or 4. Clean filter or open

ball valve closed. ball valve.

5. Motor to pump drive belts 5. Tension belts or

loose/broken or direct replace, replace direct

coupling damaged. coupling sprockets

and chain.

6. Ruptured spray hoses 6. Repair or replace.

or fittings.

1800 645 688

www.quikcorp.com.au

Problem Probable Cause Remedy

Pump delivers If hoses are jumping.

Insufficient

pressure.

1. One or more of the pump 1. Clean or replace

valves not seating properly. valves.

2. Diaphragm split (Oil will go 2. STOP PUMP!

milky in colour). Replace all 3.

See pump manual.

3. Air has not been entirely 3. Run pump with lever

evacuated from the pump. in by-pass, until all

air has evacuated.

4. Sucking air through the 4. Examine and repair.

suction line or filter.

5. Oil level is low 5. Top up with

ASE30 or 10W30.

If hoses are not jumping.

1. Damaged or worn seat or 1. Replace.

spring in the pressure

regulator.

2. Sticking pressure regulator 2. Remove slide and

slide. lubricate with marine

grease.

3. Spray nozzle/s worn, missing, 3. Replace nozzle/s with

or exceeding the pump correct size.

capacity.

4. Motor to pump drive belts 4. Tension belts or

loose/broken or direct replace, replace direct

coupling damaged. coupling sprockets

and chain.

5. Leaking hoses or fittings. 5. Repair or replace.

1800 645 688

www.quikcorp.com.au


Pump is noisy 1. Oil level is low. 1. Top up with

SAE30 or 10W30.

2. Sucking air or air in the 2. Examine and repair.

pump.

3. Blocked filter. 3. Clean filter.

Oil is changing 1. One or more diaphragms 1. STOP PUMP!

colour to white or are split. Replace all 3.

oil in the spray See pump manual.

hose.

Water returning 1. Worn safety valve (pressure 1. Replace safety valve.

to tank through adjusted too high).

the safety valve

hose.

T-400 Gun Leaks, 1. Worn seat or seal in handle. 1. Replace with T-400

repair kit.

*A full interactive troubleshooting guide can be found at

www.quikcorp.biz

1800 645 688

www.quikcorp.com.au

Your Notes__________________________________________

1800 645 688

www.quikcorp.com.au

T-400 Spray Gun_____________________________________

1800 645 688

www.quikcorp.com.au

Karin Pressure Controller_____________________________

1800 645 688

www.quikcorp.com.au

Bertolini PA 430 Pump________________________________

1800 645 688

www.quikcorp.com.au

Trouble Shooting for Radio Electrics and Reel Rewind____


Reel too hard 1. Reel break adjustment too 1. Adjust break.

to pull out. tight. (Behind clutch)

Reel rewind speed 1. Engine revs too low 1. Increase engine

too slow. Revs to ¾ revs or

2400 RPM

2. Drive belts slipping 2. Adjust belts with

belt tensoner

(Page 6)

Reel does not 1. Switch not on or faulty. 1. Switch on or replace

retract and (Fig 4)

manual button

does NOT work. 2. Flat battery on unit 2. Charge or replace

(12 Volt)

3. (5SDM) break in vehicle 3. Repair

battery connection.

4. Blown fuse 4. Replace with 10 amp

fuse.

Reel does not 1. Digital dipswitch code not 1. 12 dipswitches in

Retract and synchronised . transmitter must

Manual button correspond with the

DOES work. dipswitches on the

receiver board.

2. Discharged 9 volt 2. Replace 9 volt battery

transmitter battery.

3. Wrong transmitter 3. R=Right 27.195 MHz

9TBE or 9TDE only. L=Left 27.145 MHz

4. Faulty receiver board, 4. Call factory for radio

transmitter, pre-regulator return authorization

board, relay, or wiring. form. 1-800-645-688

1800 645 688

www.quikcorp.com.au


Reel only 1. Discharged 9 volt 1. Replace 9 volt battery

retracts at transmitter battery.

close distance.

2. Aerial broken or loose 2. Replace aerial or

on aerial base. tighten to base.

Finger tight only!

If more than finger

tight the coax cable

will break inside the

aerial base.

3. Coax cable broken inside 3. Replace aerial base

of the aerial base. and coax cable.

4. Low 12 volt battery on 4. Charge or replace

the machine. 12 volt battery. 12.5

voltage output allows

optimum

performance.

5. Faulty radio receiver board 5. Call factory for radio

or transmitter. return authorization

form. 1-800-645-688

6. Interference from overhead 6. Relocate the spraying

power lines or other possible system.

sources of radio wave

interference.

Note: Transmitters on “5TCE” units have two different built in

frequencies 27.145 for the left reel and 27.195 for the right reel.

Therefore you cannot re-code the digital dipswitch frequency for one

side to work the other side. Call the factory if you are experiencing

problems to obtain the radio return authorization form.

Quik Corp Pty Ltd

37 Production Avenue

Warana QLD 4575

1-800-645-688 Phone

1-800-645-188 Fax

Web Site: www.quikcorp.biz

Email: [email protected]

http://www.quikcorp.biz/

mailto:[email protected]

1800 645 688

www.quikcorp.com.au

Machine Specifications________________________________

5SCE 5TCE

Reels 1 2

Horsepower 5.5 5.5

Motor GX160 GX160

(Honda) U1 HXU U1 HXE8

Pump PA430 PA430

(Bertolini

Litres p/m 40 40

(Max)

PSI (Max) 580 580

PSI (Max 400 400

Working

Pressure

Electric YES YES

Start

12 Volt YES YES

Battery

Flow at 9.3 Litres 9.3 Litres

100 Meters p/minute p/minute

100 PSI



200 PSI



250 PSI



300 PSI



400 PSI

1800 645 688

www.quikcorp.com.au

Warranty Policy

This document sets out the warranties that are given by Quik Corp Pty Ltd (ABN 18

081 235 556) in relation to the Product purchased from or manufactured by Quik

Corp.

1. Definitions

1.1. In this warranty policy:

“Quik Corp” means Quik Corp Pty Ltd (ABN 18 081 235 556);

“Customer” means the party who originally acquired the Product from

Quik Corp, or an authorised distributor, reseller or dealer for Quik Corp, for

their own use.

“OEM Equipment” means the items of equipment fitted to the product by

Quik Corp and which items have been manufactured by others and have

their own manufacturer’s warranty.

“Product” means the goods or machinery that the Customer acquired and

which were manufactured by Quik Corp.

2. Warranty

2.1. Subject to clause 3 and clause 4, Quik Corp warrants to the Customer that

the Product will be free from proven defects in material and workmanship

for twelve months from the date of purchase by the Customer, unless a

specific warranty period applies to a component listed in appendix A.

2.2. The warranty is not transferable.

3. Limitations

3.1. This warranty does not cover damages resulting from shipping and

handling, abuse, accidents, alterations, normal wear or failure to maintain or

use the Quik Corp product with due care.

3.2. Quik Corp does not warrant that the operation of the product will be

uninterrupted or error free. The Customer must read and follow all

instructions and manuals for the setup, maintenance and use of the Product.

If the Customer fails to do so, the product may not function correctly and

may suffer other damage.

3.3. This warranty does not extend to OEM equipment which has its own

warrant and the Customer must rely on the OEM equipment warranty for

any defects in material or workmanship relating to the OEM equipment.

3.4. This warranty does not extend to cover corrosion due to any cause nor to

any damage to painted or anodised surfaces that occurs after the Customer

takes delivery of the product.

3.5. This warranty does not cover time required to diagnose a warranty problem.

3.6. The use of parts other than Quik Corp parts for repair of warranted items

will automatically negate any warranty. Warranted components must be

replaced with genuine Quik Corp parts.

1800 645 688

www.quikcorp.com.au

3.7. Repairs by an unauthorised agent will automatically forfeit any warranty.

Warranty repairs must be carried out by Quik Corp or an authorised Quik

Corp Dealer/Service Agent only.

3.8. This warranty does not cover transportation or insurance costs for Products

needing repair or replacement of warranted components. Nor does it cover

any freight or insurance costs in obtaining new parts or returning old parts

to Quik Corp for inspection purposes.

3.9. The time taken to remove and re-install a warranted part or component into

other brands of equipment will not be covered by the Quik Corp warranty.

Only parts and labour directly attributable to the repair of the Quik Corp

unit is covered.

3.10. Quik Corp does not pay for cleaning, or clean the Product, accessories or

work area before or after the warranty repair.

3.11. Quik Corp assumes no responsibility for improper choice of models or

where products are used in excess of rated capacities and design functions,

or under abnormal conditions. We make available a free technical service

to help with any product selection, application or situation.

4. Repair or Replace

4.1. During the warranty period, Quik Corp or its authorised Dealer/Service

Agent shall repair or replace, at Quik Corp’s discretion, without charge for

parts and standard labour, any part of the Quik Corp Product which fails

because of defects in material or workmanship unless the damage arises

from:

4.1.1. Failure resulting from neglect or misuse, such as improper

operation, lack of required maintenance or continued use of the

Product after the discovery of a defect which results in greater

damage to the Product;

4.1.2. Deteriorated or failed components such as but not limited to

diaphragms, O-rings, hoses, seals, electrical wiring and connections

damaged by corrosive chemicals, dirt and sand, excessive heat or

moisture. The Customer should ensure the type and strength of

chemicals used in the Product are compatible with the design of the

Product;

4.1.3. The use of accessories, hardware, or software which were not

manufactured by, installed by or approved in writing by Quik Corp;

4.1.4. The use of consumable items such as but not limited to oils,

lubricants, diaphragms, O-rings, hoses seals, gaskets, filter elements,

flow meters, clutches, drive belts, pivot pins, paint, batteries, radio

transmitters, radio relays, push buttons, switches, hose rollers,

aerials, spray guns and nozzles as these items are considered to be

normal wear items and are not warranted;

4.1.5. Component failure caused by not performing scheduled

maintenance service such as oils, grease, failure to clean tanks,

pumps, filters, spray lines, nozzles or any other components and not

1800 645 688

www.quikcorp.com.au

tightening or replacing loose or missing bolts, nuts, fittings, shields

and covers;

4.1.6. Damage or machine failure caused by carelessness or accidental

damage, improper operation, inappropriate transportation or storage

of the Product;

4.1.7. Any contamination or leakages caused or induced by the Customer;

4.1.8. Any use or operation of the Product outside the physical, electrical

or environmental specifications of the Product;

4.1.9. Any alterations, modifications, attachments or unauthorised repairs

to the Product which have not been authorised in writing by Quik

Corp; and

4.1.10. Failures due to faulty or inadequate electrical sources of power.

5. OEM Warranties

5.1. All OEM (Original Equipment Manufacturer) components are covered by

the Original Manufacturer’s Warranty. It is the Customer’s responsibility

to familiarise themselves with these warranties, and subject to clause 7, that

is the only warranty given to the customer in respect of that part of the

Product.

6. Statutory Rights and Exclusions (New Zealand Only)

6.1. If the Product has been acquired for the purposes of a business then

pursuant to section 43(2) of the Consumer Guarantees Act 1993 (“CGA”) it

is agreed that the provisions of the CGA do not apply. To the fullest extent

permitted by law in New Zealand, Quik Corp excludes any liability for any

direct or indirect loss or damage of any kind arising from the Product,

including consequential loss or damage or loss of profits, and loss or

damage arising from the negligence of Quik Corp’s employees and agents.

The warranty is personal to the Customer and cannot be transferred to a

subsequent purchaser (although the purchaser, in some circumstances, may

have rights under the CGA or the Sale of Goods Act). These exclusions do

not exclude Quik Corp’s liability in respect of any warranties or guarantees

implied by any relevant legislation in New Zealand which cannot legally be

contracted out of.

7. Warranty Claim Procedure

7.1. To obtain warranty service:

7.1.1. The Warranty Registration Form must be returned to Quik Corp by

the Customer within 14 days of taking delivery of the Product;

7.1.2. The Customer must read the Operating manual before operating the

Product;

7.1.3. The Customer must provide with notice of the defect Quik Corp

within the warranty period and within 14 days of discovery of the

1800 645 688

www.quikcorp.com.au

claimed problem, and allow reasonable time for replacement or

repair.

7.2. Quik Corp may, at its discretion, request the Customer to deliver the alleged

defective parts to an authorised servicing Dealer/Service Agent or to Quik

Corp. Transportation of the Product to the authorised servicing

Dealer/Service Agent or Quik Corp for warranty work is the responsibility

of the Customer and is at the Customer’s expense. Alternatively, the

Customer may request a Quik Corp service technician to travel to the site of

the Product to effect repairs or replacement, however the reasonable travel

costs (including traveling time) of the service technician must be paid for

by the Customer.

7.3. Any service outside the scope of this warranty will be charged for at Quik

Corp’s rates and terms then in effect.

8. Other

8.1. This warranty is in lieu of all other warranties (except those of title),

expressed or implied, and there are no warranties of merchantability or

fitness for a particular purpose.

8.2. Unless the Product has been purchased for personal, domestic or household

use, any liability of Quik Corp to the Customer arising under statute which

may not be excluded restricted or modified by agreement in limited to an

amount equal to, as determined by Quik Corp:

8.2.1. Replacement of the Product or supply of equivalent Product;

8.2.2. The repair of the Product;

8.2.3. The payment of the cost of replacing or repairing the Product; or

8.2.4. Refund of the purchase price paid by the Customer.

8.3. Subject to clause 7.2, in no event shall Quik Corp or the authorised

Dealer/Service Agent be liable for any loss of profit or any consequential,

indirect or special loss, damage or injury of any kind whatsoever arising

directly or indirectly from the Product or any defect.

8.4. The benefits under this Warranty are in addition to other rights and

remedies under a law in relation to the Product.

8.5. The judgement of Quik Corp in all cases of claims under this warranty shall

be final and conclusive and the Customer agrees to accept its decisions on

all questions as to defect, repair and to the exchange of any part or parts.

Appendix A:

1. Bertolini Pumps – Warranty period is 6 months. If Quik Flush pump and tank cleaner is used from new then the warranty period is extended to 18 months.

2. Honda Motors – Refer to your Honda Manual. (Warranty period is up

to 3 years)

3. Radio Receiver – Warranty period is 5 years on all non-moving parts.

1800 645 688

www.quikcorp.com.au

1800 645 688

www.quikcorp.com.au

Quik Corp Pty Ltd

Warranty Division

37 Production Avenue

Warana QLD 4575

Australia

-------------------------------------------------------------------------------------------------------

Fold here and seal at top for retuning by Post

congratulations - quik spray · page 2 1800 645 688 congratulations_____ quik corp would like to...

Documents