consolidation test - 023
TRANSCRIPT
FACULTY OF CIVIL & ENVIRONMENTAL ENGINEERING
DEPT.OF GEOTECHNICAL AND TRANSPORTATION ENGINEERING
GEOTECHNICAL ENGINEERING LABORATORY
REPORT
SUBJECT CODE
TEST CODE & TITLE MG001 - CONSOLIDATION TEST
COURSE CODE
TESTING DATE
STUDENT NAME
GROUP
GROUP MEMBER NAMES
1.
2.
3.
4.
5.
LECTURER/ INSTRUCTOR/ TUTOR NAME
REPORT RECEIVED DATE
MARKSATTENDANCE/ DISCIPLINE & INVOLVEMENT
/15%
DATA ANALYSIS /20%
RESULT /20%
DISCUSSION /25%
CONCLUSION /20%
TOTAL /100%
EXAMINER COMMENT RECEIVED STAMP
STUDENT CODE OF ETHIC(SCE)
DEPT. OF GEOTECHNICAL AND TRANSPOTATION ENGINEERING
FACULTY OF CIVIL & ENVIRONMENTAL ENGINEERING
I, hereby confess that I have prepared this report on my own effort. I also admit not to receive or give any help during the preparation of this report and pledge
that everything mentioned in the report is true.
_________________Student Signature
Name : …………………………………………
Matric No. : …………………………………………
Date : …………………………………………
FACULTY: CIVIL & ENVIRONMENTAL ENG. PAGE NO.: 1/8DEPARTMENT: GEOTECHNICAL AND TRANSPORTATION ENGINEERING
EDITION:
REVIEW NO.:
TEST TITLE : CONSOLIDATION TEST(MARINE CLAY AND PEAT SOIL)
EFFECTIVE DATE:
5/12/07
AMENDMENT DATE:
5/12/07
1.0 OBJECTIVETO DETERMINE THE CONSOLIDATION CHARACTERISTICS OF SOILS OF LOW PERMEABILITY
2.0 LEARNING OUTCOME
At the end of this experiment, students are able to: Conduct one dimensional consolidation test Identify the factors causes soil consolidation Determine the consolidation parameters (cv, mv, Cc and Pc)
3.0 THEORY
When a fully saturated soil is subjected to a compressive stress, its volume tends to decrease. The decreasing of its volume is due to compression of the solid grains and escape of water from the voids. In a free drainage soil such as saturated sand the escape of water can take place rapidly. But in clay, due to low permeability, the movement of water occurs very much slowly and therefore, considerable time may be required for excess water to be squeezed out to permeable boundaries.
Settlement is the direct result of the decrease in soil volume and consolidation is the rate of volume decrease with time. The consolidation test is use to estimate the amount of settlement and time of consolidation. From this test some consolidation parameters such as coefficient of consolidation (cv), coefficient of volume compressibility (mv), compression index (Cc), preconsolidation pressure (Pc) can be determined.
There are two methods for determining the coefficient of consolidation:(i) Casagrande or log (time) or 50% consolidation(ii) Taylor or √ time or 90% consolidation
The coefficient of consolidation can be determined by this equation,
(3.1)
Where, cv = coefficient of consolidation (m2/year)Tv = Time factorH = Maximum length of drainage path (m)t = Time to achieve 50% or 90% consolidation (year or minute)
FACULTY: CIVIL & ENVIRONMENTAL ENG. PAGE NO.: 2/8DEPARTMENT: GEOTECHNICAL AND TRANSPORTATION ENGINEERING
EDITION:
REVIEW NO.:
TEST TITLE : CONSOLIDATION TEST(MARINE CLAY AND PEAT SOIL)
EFFECTIVE DATE:
5/12/07
AMENDMENT DATE:
5/12/07
Figure 3.1: Settlement versus log Time
Figure 3.2: Settlement versus square root time
FACULTY: CIVIL & ENVIRONMENTAL ENG. PAGE NO.: 3/8DEPARTMENT: GEOTECHNICAL AND TRANSPORTATION ENGINEERING
EDITION:
REVIEW NO.:
TEST TITLE : CONSOLIDATION TEST EFFECTIVE DATE:
5/12/07
0
20
40
60
80
100
120
140
160
0.1 1 10 100 1000 10000
Time (minute)
Set
tlem
ent
(mm
)
100% consolidation line
A
B = 4A
δδ
0% consolidation line
50% consolidation line
t50
0
5
10
15
20
25
30
0 5 10 15 20 25 30 35 40
Square Root Time (minute)
Set
tlem
ent
(mm
)
x
1.15x
√t90
12
(MARINE CLAY AND PEAT SOIL) AMENDMENT DATE:
5/12/07
4.0 TEST EQUIPMENTS
1. Consolidation apparatus - Consolidation ring - Corrossion-resistant porous plate - Consolidation cell - Dial Gauge - Loading device 2. Balance readable to 0.1g3. Vernier caliper4. Stop-clock readable to 1 s
5.0 PROCEDURES
1. Measure the internal diameter (D) and the height of the ring, using internal vernier calipers.
2. Weight the ring to the nearest 0.01g (mR).3. Cutting the specimen and trimming into ring.4. Determine the initial moisture content from trimming soil.5. Determine the weight of ring and specimen (m1)6. Determine the mass of bulk specimen (m) to the nearest 0.01g using this equation
m = m1 – mR
7. Place the consolidation ring and specimen (cutting edge uppermost) centrally on the porous disc.
8. Fit the ring retainer and cell body and then place the upper porous disc centrally on top of the specimen.
9. Place the consolidation cell centrally in position on the platform of the machine base.10. Lift the end of the beam to allow the loading yoke to be raised to the vertical position
and adjust the loading stem by screwing it downwards until the end engages closely in the recess on the top of the loading cap
11. Attach the compression dial gauge to the arm on the support post.12. Add weight (2.5 kg) carefully to the load hanger13. Add water at room temperature to the cell and make sure that the specimen and upper
porous disc are completely submerged. 14. Wind down the beam support and at the same time start the clock. 15. Observe the compression gauge readings and the clock, and record the readings on a
consolidation test form at the selected time intervals.
16. Plot the readings of the compression against time to a logarithmic scale and against square-root-time.
FACULTY: CIVIL & ENVIRONMENTAL ENG. PAGE NO.: 4/8DEPARTMENT: GEOTECHNICAL AND TRANSPORTATION ENGINEERING
EDITION:
REVIEW NO.:
TEST TITLE : CONSOLIDATION TEST(MARINE CLAY AND PEAT SOIL)
EFFECTIVE DATE:
5/12/07
AMENDMENT DATE:
5/12/07
6.0 CALCULATION EXAMPLE
Date started: 9/7/07 Sample No.: A1 - 1Soil Type: Silty clay Cell No: 4
BEFORE TEST
Moisture content from trimming: 22.9 (%) S.G. (Assumed) : 2.7Weight of ring : 439.35 (g) Diameter of ring : 74.9 (mm)Weight of sample + ring: 260.43 (g) Area of ring: 4406 (mm2)Weight of sample : 178.92 (g) Thickness of ring: 20.1 (mm)Weight of dry sample: 145.35 (g) Volume of ring : 88.56 (mm3)Weight of initial moisture: 33.57 (g) Density, : 2.02 (Mg/m3)Initial moisture content: 23.1 (%) Dry density, d : 1.64 (Mg/m3)
Initial void ratio, = 0.622
SETTLEMENT READINGSElapse time
Time (min)
√ timeClock time
Gauge reading
Cumulative compression, H
(mm)hr min sec
0 0 0 8.00 am 0 010 0.17 0.41 21 21 x 0.002 = 0.0420 0.33 0.57 23 23 x 0.002 = 0.0530 0.50 0.71 25 25 x 0.002 = 0.0540 0.67 0.82 29 29 x 0.002 = 0.0650 0.83 0.91 35 35 x 0.002 = 0.07
1 1 1.00 8.01 am 41 41 x 0.002 = 0.082 2 1.41 8.02 am 49 49 x 0.002 = 0.104 4 2.00 8.04 am 58 58 x 0.002 = 0.128 8 2.83 8.08 am 66 66 x 0.002 = 0.13
15 15 3.87 8.15 am 75 75 x 0.002 = 0.1530 30 5.48 8.30 am 86 86 x 0.002 = 0.17
1 60 9.00 am 95 95 x 0.002 = 0.192 120 10.00am 107 107 x 0.002 = 0.214 240 12.00 pm 115 115 x 0.002 = 0.238 480 4.00 pm 124 124 x 0.002 = 0.25
24 1440 8.00 am 126 126 x 0.002 = 0.25
FACULTY: CIVIL & ENVIRONMENTAL ENG. PAGE NO.: 5/8DEPARTMENT: GEOTECHNICAL AND TRANSPORTATION ENGINEERING
EDITION:
REVIEW NO.:
TEST TITLE : CONSOLIDATION TEST(MARINE CLAY AND PEAT SOIL)
EFFECTIVE DATE:
5/12/07
AMENDMENT DATE:
5/12/07
7.0 RESULTS
CONSOLIDATION TEST – CALCULATION SHEET
Date started:_________________ Sample No.: _______________
Soil Type: __________________ Cell No: ________________
BEFORE TEST
Moisture content from trimming: _______(%) S.G. (Assumed) : 2.7
Weight of ring : ___________________ (g) Diameter of ring : _______________(mm)
Weight of sample + ring: ____________ (g) Area of ring: ___________________(mm2)
Weight of sample : _______________ (g) Thickness of ring: _______________(mm)
Weight of dry sample: _______________(g) Volume of ring : _________________(mm3)
Weight of initial moisture: ____________(g) Density, : _____________________(Mg/m3)
Initial moisture content: ______________(%) Dry density, d : _________________ (Mg/m3)
Initial void ratio, = ____________
SETTLEMENT READINGS
Elapse timeTime (min)
√ timeClock time
Gauge reading
Cumulative compression
, H (mm)hr min sec
01020304050
1248
1530
1248
24
FACULTY: CIVIL & ENVIRONMENTAL ENG. PAGE NO.: 6/8DEPARTMENT: GEOTECHNICAL AND TRANSPORTATION ENGINEERING
EDITION:
REVIEW NO.:
TEST TITLE : CONSOLIDATION TEST(MARINE CLAY AND PEAT SOIL)
EFFECTIVE DATE:
5/12/07
AMENDMENT DATE:
5/12/07
8.0 CALCULATIONS
FACULTY: CIVIL & ENVIRONMENTAL ENG. PAGE NO.: 7/8DEPARTMENT: GEOTECHNICAL AND TRANSPORTATION ENGINEERING
EDITION:
REVIEW NO.:
TEST TITLE : CONSOLIDATION TEST(MARINE CLAY AND PEAT SOIL)
EFFECTIVE DATE:
5/12/07
AMENDMENT DATE:
5/12/07
9.0 DISCUSSIONS
10.0 CONCLUSIONS
FACULTY: CIVIL & ENVIRONMENTAL ENG. PAGE NO.:DEPARTMENT: GEOTECHNICAL AND TRANSPORTATION ENGINEERING
EDITION:
REVIEW NO.:
TEST TITLE : CONSOLIDATION TESTEFFECTIVE DATE:AMENDMENT DATE:
11.0 OPEN ENDED QUESTIONS
QUESTIONS 1
1. From your experimental data, determine the coefficient of consolidation, cv (m2/year) using Casagrande Method. Please comment your answer.
2. Clay samples collected from 5 metres deep in Batu Pahat has a unit weight () of 18 kN/m3. The following data were recorded during an oedometer test.
Effective Stress (kN/m2) 25 50 100 200 400 800 200 50Void ratio (e) 0.85 0.82 0.71 0.57 0.43 0.3 0.4 0.5
(i) Plot the graph of void ratio against effective stress on semi-log graph and determine the compression index (Cc), Preconsolidation pressure (Pc) and coefficient of volume compressibility (mv).
(ii) Define whether the soil is normally consolidated or over consolidated.
QUESTIONS 2
1. From the experimental data , determine the coefficient of consolidation, cv (m2/year) using Taylor Method. Please comment your answer.
2. Clay samples collected from 10 metres deep in Parit Raja has a unit weight () of 20 kN/m3. The following data were recorded during an oedometer test.
Effective Stress (kN/m2) 50 100 200 400 800 1600 400 100Void ratio (e) 0.95 0.92 0.81 0.67 0.53 0.4 0.5 0.6
(i) Plot the graph of void ratio against effective stress on semi-log graph and determine the compression index (Cc), Preconsolidation pressure (Pc) and coefficient of volume compressibility (mv).
(ii) Define whether the soil is normally consolidated or over consolidated.