construction materials
DESCRIPTION
Home RehabTRANSCRIPT
-iammsHORN GROUT
.mmsSPEED PLUG HYDRAULIC CEMENT
Horn grout - a non shrink, non corrosive multi flow high early strengthgrout. It may be packed, rodded, vibrated, poured or pumped. Complieswith Corp of Engineers specs CRD-C621 and C1107. Also complies withvarious state DOT specs, NYS DOT 701.05 and 701.06. Yield: .43 cu.ft./bag.
SPEED PLUG is a quick setting hydraulic cement compound used toinstantly stop running water or seepage leaks in masonry or concrete.The SPEED PLUG formulation is nonshrinking, nonmetallic, and noncorrosive. SPEED PLUG requires only potable water for mixing, andachieves initial set in 1 to 3 minutes, even when applied under water.Yield: 1lb. of SPEED PLUG yields approximately 17 cu. in. and will repairapproximately 30 inches of 314" x 314" crack.
Part No.
TAM10100
StandardPackage
50 lb. Bag (V2 cu. ft.)
SkidQuantity
60Part No.
TAM10400
StandardPackage
50 lb. Pail
SkidQuantity
36
-iammsHORNWELD BONDING AGENT
SmmsDURALTOP GEL KIT
A reemulsifiable surface bonding agent to improve adhesion of plaster,concrete and other cementitious products to almost any sound surface.Apply by roller, brush, or spray.
COVERAGE: 200-250 sq. ft./gal. on dense surfaces. Porous surfacesmay require more material.
DURALTOP GEL is a fast setting, two component, polymer reinforced,non sag, cementitious patching and repair mortar. DURALTOP GELachieves high, early compressive, flexural, and bond strengths. DURALTOP GEL contains a migratory corrosion inhibitor and offers excellentadhesion and high build non sag properties. DURALTOP GEL is suppliedas a preprotioned unit and is compatible with the coefficient of thermalexpansion of concrete. NYS DOT Item 701.08. Yield: .4 cu. ft./Kit.
Part No.
TAM10200
StandardPackage
5 Gal. Pail
SkidQuantity
36 Part No.
TAM10700
StandardPackage
60 lb. Kit
SkidQuantity
48
-iammsRAPID ROCK mRAULIC COMPOUND
-iammsDURAL 308 EPOXY WATERPROOFING
Rapid Rock - a non shrinking, quick setting, high strength hydrauliccompound for anchoring posts and signs, etc. It mixes in 1-3 minutes,sets in 15 minutes, and achieves over 5000 PSI in 1 hour. Yield: .5 cu. ft./50 lb. Pail.
Part No.Part No.StandardPackage
SkidQuantity
Dural 306 is a coal tar modified, 100% solids epoxy resin used as awaterproofing membrane or as a non skid surface for bridge decks,parking garages, and loading ramps. NYS DOT approved 717.02 alsoapproved Port Auth. of NY and NJ. Yields vary depending on usage.
StandardPackage
TAM10300 50 lb. Pail 36 TAM11020 10 Gal. Kit
1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631-242-8555 • FAX: 631-667-8869 81
SmmsSPEED CRETE® - GREEN UNE HORIZONTAL PATCHING CEMENT
SmmsSPEED CRETE® - 2028 RAPID SETTING MORTAR
A cement based high early strength semi-flowable patching formulationfor horizontal surfaces on highways, bridges, loading docks. Superiorload bearing strength meets and exceeds ASTM C-928. Achieves initialset in less than 15 minutes. Approvals: MTA Bridges and Tunnels, NYCDOT, Suffolk County Highways and Bridges, Nassau County Highwaysand Bridges. Yield: .5 cu. ft./bag.
Part No.
TAM 10500
StandardPackage
50 lb. Bag
SkidQuantity
48
SPEED CRETE 2028 is a cement based, ready to use, patching andrepair mortar which sets fast and achieves rapid strength gain. SpeedCrete 2028 develops a tenacious bond, has excellent resistance tofreeze-thaw and weathering and achieves a compressive strength of2600psi within 1 hour at 75°F. Widely used on horizontal concretesurfaces such as highways, bridge decks, parking decks, loading docks,pavement joint repairs and industrial floors. Yield: .42 Cu ft/bag ..75 Cuft/bag when extended with 50 Ibs. of %" pea gravel. NYS DOT approval701.09.
A polymer modified cement based compound that can be applied fromfeather edge up to 1" in one application. Add water only. Use for repairingbroken or spalled areas and the resurfacing and leveling of concretewalls, floors, steps, walks, etc. Yields: .5 cu. ft./bag.
A cement based fast setting patching material for concrete under waterand wet area patching. It is used in the restoration of concrete man holes,pilings, sea walls, and dams. Blue Line's consistency enables fast, easyfinishing on underwater applications. Approvals: NYC DOT, NJ DOT,Suffolk County Highways and Bridges. Yield: .5 cu. ft./bag.
A cement based fast setting patching material for concrete. Putty likeconsistency enables fast, easy finishing on vertical and overhead applications without forms. Also may be used horizontally. Complies withASTM C-928, NYC DOT, Suffolk County Highway and Bridges, NassauCounty Highways and Bridges. Yields: .5 cu. ft./bag neat, .7 cu. ft./bagwhen extended with 40 Ibs. of %" pea gravel.
SmmsSPEED CRE1E® • BWE UNE UNDERWATER PATCHING CEMENT
4 Gal.
CaseQuantity
48
SkidQuantity
StandardPackage
StandardPackage
50 lb. Bag
4 Gal. (2 Part) Kit
TAM10660
Part No.
TAM11600
Part No.
A 2 part, 100% solids epoxy bonding compound designed for bondingfresh concrete to existing surfaces. Approvals: NJ DOT, Port Auth. of NYand NJ.
COVERAGE: As bonding compound for fresh to old concrete 80 - 90 sq.ft./gal. For anchoring, 1 neat gal. yields 231 cu. in. of grout. 1 gal. neatDURALBOND with 1 gal. dry 20-40 mesh silica sand will yield approximately 410 cu. in. of mortar. Coverage will vary depending on surfacetexture, porosity and temperature.
DURAL 104 is a bonding compound for adhering new, fresh concrete toold or existing concrete. It is a two-component, 100% solids, epoxylpolysulfide resin system. DURAL 104 conforms with the following specifications. New York State DOT approved, item 701.03. Epoxy bonding andgrouting compound. COVERAGE: 50 -100 sq. ft.
SmmsDURALBOND BONDING COMPOUND
SmmsDURAL 104 EPOXY BONDING AND GROUT COMPOUND
48
SkidQuantity
48
SkidQuantity
StandardPackage
StandardPackage
50lb.Bag
50 lb. Bag
TAM10600
Part No.
TAM10650
Part No.
SmmsTHIN PATCH
.mmsSPEED CRE1E® • RED UNE VERTiCAlAND OVERHEAD PATCHING CEMENT
Part No.StandardPackage
SkidQuantity Part No.
StandardPackage
TAM11900 60 lb. Bag 48 TAM11700 4 Gal. Kit
880 MEEKER AVE • BROOKLYN, NY 1122282 Tel: 718..387..0300 • FAX: ,718-387-1874
.mmsDURAL CREIE PATCHING AND ANCHORING CEMENT
A high modulus high strength epoxy adhesive and mortar binder systemused for horizontal and vertical patching and repair, as well as anchoringbolts and crack injection.
COVERAGE: DURALCRETE formulations coverage rates are approximate and for estimating purposes only. Surface temperature, porosityand texture will determine actual material requirements.
SmmsHORN WB-309 CURING AND DUST PROOFING COMPOUND
HORNCURE WB-309 is a VOC compliant, clear, water soluble product for treatingconcrete. In addition to working as a cure agent for freshly placed concrete,HORNCURE WB-309 penetrates the concrete surface pores and reacts chemicallywith the lime and other soluble calcium compounds in the portland cement. Theresult is a hard, dust proof, easy to clean serfuce.
COVERAGE: The following coverage rates are approximate and for estimatingpurposes only.
DURALCRETE DURALCRETE LV DURALCRETE GEL200 sq. ft./gal. 250 sq. ft./gal. 150 sq. ft./gal.Prime Coat
Resin: Aggr (by vol)(mixed with silica aggregate) - 1:3Approx. gals. to make 1 cu. ft. 2.2:8.0
1:42.2:8.8
1:14.7:4.7
Fresh ConcreteExisting Concrete
Part No.
Sq. FUGal. per coat400-600200-400
Standard Package Skid Quantity
A high modulus high strength epoxy adhesive and mortar binder systemused for horizontal and vertical patching and repair as well as anchoringbolts and crack injection. Fast cures or when application temperature isbelow 50° F.
COMPLIANCE: DURALITH GEL meets ASTM C881-90 Type 1 & Type IV,Grade 3, Class A. DURALITH LV meets ASTM C881-90, Type I, Grade 1,Class A.
HORNCURE 30 is a liquid membrane forming curing compound. It can be appliedto any concrete surface, indoors or outdoors, and provides excellent initial cure tothe concrete by preventing rapid evaporation of water. HORNCURE 300 is a lowviscosity hydrocarbon resin which contains a fugitive dye. The dye disappearswhen exposed to sunlight and does not stain concrete. HORNCURE 30D is formulated to meet ASTM C309, Type ID, Class A &B.
COVERAGE: Because of variations in surface density, the following coverage ratesare approximate and are intended for estimating purposes only.
200 - 300 Square Feet per Gallonor 4.9-7.3 Square Meters per Liter
SmmsHORN CURE 300 CURING COMPOUND
StandardPart No. Description Package
TAM10910 Duralcrete LV 3 Gal. Unit
Duralcrete & Duralcrete Gel available on request
.mmsEPOXY REPAIR
CaseQuantity
TAM11300TAM11355
Part No.
TAM11200TAM11255
5 Gal. Pail55 Gal. Drum
Standard Package
5 Gal. Pail55 Gal. Drum
364
Skid Quantity
364
For coating on bridges, piers and abutements. New York State DOTapproved, item 717.01, Suffolk County Highways and Bridges, NassauCounty Highways and Bridges, NJ DOT.
iammsDURAL 383 EPOXY COATING
Part No.
TAM10800TAM10810
StandardPackage
15 oz. Tech Kit3 Gal. Unit
CaseQuantity
121 iamms
FORMSHIELD
FORMSHIELD is a low cost, highly effective release agent for metal, plastic, woodand composition forms. It is a blend of natural organic chemicals which impart awaterproof film to prevent adhesion of concrete to the forms and prOVide for quickand easy release. FORMSHIELD is supplied ready to use as a thin, amber coloredliquid of low viscosity.
COVERAGE:Plywood Forms 350 - 500* sq./ft./gal.Wood Composition Forms 350 - 500* sq./ft./gal.Metal Forms 800 - 1000* sq./ft'/gal.Plastic Forms 800 - 1000* sq./ft'/gal.
* Approximate rates may vary depending on porosity and texture of the surface.
Part No.
TAM11010
StandardPackage
4 Gal. Unit
Part No.
TAM11400TAM11455
Standard Package
5 Gal. Pail55 Gal. Drum
Skid Quantity
364
1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631-242-8555 • FAX: 631-667-8869 83
I
.mms REXOUTH EPOXY OVERLAY .mms AIOIRD-n BOI\lllNG MIXTURE
A water based primer for use on unprimed concrete or masonry prior toapplying Aquathane. Can be brushed, rolled or sprayed.
Overlays Broadcoast Method - 15t Coat 2nd Coat Seal CoatFlexolith 216 (sq. ft./gal.) 40 25 80Basalt #8 Aggregate (Ibs./sq. ft.) 1.2 1.5Troweldown Flexolith Flexolith/Aggregate Seal CoatPrime Coat 230 sq. ft./
gal.
A flexible, rapid setting, traffic resistant (pedestrian, auto and truck)epoxy resurfacing system. It is also used for epoxy patching and mortarbinder. Flexolith is a two component, 100% epoxy compound that ismoisture insensitive.
COVERAGE: FLEXOLITH coverage rates are approximate, and for estimating purposes only. Suriace temperature, porosity, and texture willdetermine actual material requirements.
Mortar - Silica Sand 1:3 by volumeMortar - Tamms 5H 1:5 by volumeFlexolith 216 200 sq. fl./
gal.Mortar/Patching Flexolith Flexolith LV Flexolith
GelPrimer 250 sq. ft./ 250 sq. ft./gal. 50 sq. ft./
gal. gal.Resin/Aggr (by Vol.) 1:3 1:4.5 1:1Approx. Gals./Cu. Ft. 2.6:8.0 2:9.1 4.7:4.7
StandardPart No. Package
TAM12000 4 Gal. Case
805040
48 Bags
SheetsPer Skid
SkidQuantity
5Gal.
StandardPackage
StandardPackage
SOlb. Bag
Part No.
TAM12300
TAM12400 W' x 4' x 10'TAM12410 3/4" x 4' x 10'TAM12420 1" x 4' x 10'
A heavy duty, high early strength, non shrink grout. It may be packed,rodded, vibrated, poured or pumped. Complies with Corp. of Engineersspec. CRD-C621.
CUT SIZES AVAILABLE ON REQUEST
An integral bonding admixture for improving the periormance of cementbased coatings, stucco, terrazzo, and concrete patching products. Itimproves the flexural strength, and improves bond strength and outdoordurability.
HORNBOARD Asphalt Impregnated Fiber Expansion Filler is composedof tough, resilient, cellulose fibers securely bonded together with auniform impregnation of bituminous binder and preformed into strips orsheets. The material is strong but light-weight; cuts and handles easily;resists breakage. It will not extrude from the joint under normal compression and service temperatures, and does not embrittle in cold weather.Installation is easy; HORNBOARD will not tWist, break or deform withordinary handling. It cuts cleanly, places readily, stays strong and soundthrough many years of repeated expansion/contraction cycles.
Part No. Size Sheet
tamms HORNBOARO EXPANSION JOINTFILLER
TAM12200
Part No.
Horn cork is an expansion joint material composed of selected granulated cork, bonded together with a phenolic resin. Complies with ASTMD-1752 type 2.
Smms GROUT SUPREIVI
Smms HORN CORK EXPANSION JOINT
4 Gal. Kit4 Gal. Kit
StandardPackageColor
Clear-MattClear-Gloss
TAM18100TAM18101
Part No.
.mms TAMMS HP PRIMER
Smms AQUATIIANE ANTI GRAFFITI COATII\IGA high performance non-sacrificial aliphatic poly eurethene protectivecoating and anti graffiti for interior or exterior use. It has excellent chemical and weathering resistance. It is a two component, clear, non yellowing product that meets most VOC requirements. NYC School Construction Auth. approval.
COVERAGE: AQUATHANE coverage rates are approximate and are forestimating purposes only. Surface porosity and texture will determineactual material requirements. Apply samples to all surfaces to be covered. Obtain approval ofthe architect or owner for the finish and coveragebefore proceeding with the job. Retain the mock-up through the completion of the job. Typical coverage rates for AQUATHANE are as follows:
Surface CoveragePrimed concrete/masonry 300 - 400 sq. ft./gal.DURAL epoxy coatings 450 - 550 sq. ft'/gal.Steel 450 - 550 sq. ft'/gal.Two coats are recommended for most applications.
Part No. Standard Package Part No. SizeTAM11810 5 Gal. Pail TAM12500 Cut to Spec.
880 MEEKER AVE • BROOKLYN, NY 1122284 Tel: 718-387-0300 • FAX: 718-387-1874
MASTER BUILDERSEMACO® 1415 REPAIR MORTARRapid strength repair mortar
DESCRIPTION:EMACO® T415 is based on new high performance cement technologyresulting in high early strengths at a wide range oftemperatures. This onecomponent product can be placed into service in a little as 2 hours forstandard rubber tire traffic.
RECOMMENDED FOR:• Highway overlays and repairs• Parking structure deck and ramp repairs• Concrete floor repairs• Full depth patching repairs• Concrete pavement joint repairs• Wastewater treatment facility repairs
FEATURES/BENEFITS:• Wide temperature use range - from 20° to 85° F (-7° to 29° C)• Rapid high early strength - over 2000 psi in 2 hours• Excellent bond - no bonding agent required• Resistant to damage caused by freeze-thaw cycles• Meets ASTM C 928 for very rapid repair• Economical with the added capability to extend up to 55% by weightfor deep patches
Yields: .45 cu. ft./bag neat, .58 cu. ft./ when extended with 55%3/8" aggregate.
MASTER BUILDERSSEY® 45 CHEMICAL-ACTION CONCRETEDESCRIPTION:SET 45 is a one component concrete repair and anchoring materialwhich sets in 15 minutes and takes rubber-tire traffic 45 minutes afterplacement. This product bonds to both concrete and masonry and canbe used indoors and outdoors for a variety of highway and heavyindustrial repair jobs. It comes in two formulations - SET 45 Regular for use inambient temperatures below 85°F (29°C); and SET 45 Hot Weather for use inambient temperatures ranging from 85°F to 100°F (29°C to 38°C).Note: Regardless of the temperature, SET 45 Hot Weather formula withaggregate should be used for large placements.RECOMIVI:NDED FOR:• Bridge deck and highway overlays• Concrete pavement joint repairs• Airport runway light installations• Full depth structural repairs• Expansion device nosings• Commercial freezer room repairs• Parking deck and ramp repairsFEATURES/BENEFITS:• Easy-to-use - just add water• Wide temperature use range - from below freezing to hot weatherexposures
• Rapid, high-early strength• Superior bonding - no bonding agent is needed• Resistant to freeze/thaw cycles and deicing chemicals• Only air-curing requiredYields: .39 cu. ft./bag neat, .58 cu. ft. when extended with 60% W'rounded sound aggregate.
Part No.
MB30055
Standard Package
55 lb. Bag
Skid Quantity
60 BagsPart No. Standard Package Skid Quantity
Rapid strength repair mortar with extended working time
DESCRIPTION:EMACO T430 is based on new high performance cement technologyresulting in high early strengths at a wide range of temperatures. This onecomponent product can be placed into service in as little as 6 hours forstandard rubber tire traffic. EMACO T430 is specially suited for hotweather applications when extended working time is required.
RECOMMElIIOm FOR:• Highway overlays and repairs• Parking structure deck and ramp repairs• Concrete floor repairs• Full depth slab repairs• Concrete pavement joint repairs• Wastewater treatment facility repairs• Truck dock repairs
FEATURES/BENEFITS:• Wide temperature use range-from 40° to 100° F (4° to 38° C)• Rapid high early strength - over 2000 psi in 6 hours• Excellent bond· no bonding agent required• Resistant to damage caused by freeze/thaw cycles• Meets ASTM C 928 for rapid repair• Economical-with the capability to extend up to 55% by weight for
deep patches
Yields: .40 cu. ft./bag neat, .58 cu. ft. when extended with 55%318" aggregate.
MASTER BUILDERSEMACO® 1430 REPAIR MORTAR
A rheoplastic, one component, cement-based, shrinkage-compensatedmortarDESCRIPTION:EMACO S88-CA is a rheoplastic, silica fume, fiber reinforced, one component, high-strength, cement-based, shrinkage-compensated mortar.It is specially designed for repairing concrete or masonry structures andcan be applied by low pressure spraying or hand troweling.RECOMMENDm FOR:• Vertical and overhead applications• Bridges, beams, parking garages and tunnels• Piers, manholes, sewers, navigation locks, dams, sea walls and
masonry surfaces
FEATURES/BENEFITS:• One component, factory controlled for uniform results• Easy-ta-use - requires only the addition of potable water for mixing• Sprayable• Shrinkage-compensated to reduce early shrinkage cracking• High early and ultimate compressive, flexural and bond strengths• Extremely low permeability• Sulfate-resistant• Freeze-thaw durable
Yield: .45 cu. ft./bag.
MASTER BUILDERSEMACO® S8B·eA MORTAR
6060
60
Skid Quantity
50 lb. Bag50 lb. Bag
55 lb. Bag
Standard Package
MB88055
Part No.
MB40050 (Regular)MB40060 (Hot Weather)
60 Bags
Skid Quantity
55 lb. Bag
Standard PackagePart No.
MB10010
. 1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631-242-8555 • FAX: 631-667-8869 85
MASTER BUILDERSEMACO® S77-CR fLOWABLE MORTAR
MASTER BUILDERSEMACO® P22 REBAR COATING
Sulfate and chloride-resistant one component cement-based flowablerepair mortar
DESCRIPTION:EMACO S77-CR is a rheoplastic, pourable form and pump repair mortarsystem. Its unique formulation provides excellent bond, resistance tosulfates and chlorides, high electrical resistivity, low permeability andhigh compressive strengths. EMACO S77-CR provides high pumpabilityfor structural repairs of columns and beams.
RECOMMENDED FOR:• Formed vertical and overhead applications• Heavy-duty, durable, long-lasting repairs in aggressive environments• Marine structures, water and wastewater facilities and manholes• Bridges, tunnels, concrete pipe. parking structures and ramps• Freeze/thaw environments• Excellent pumpability for high strength repair of columns and beams
FEATURES/BENEATS:• Silica fume formulation provides a material with low permeability• Excellent chloride and sulfate resistance• High electrical resistivity• High strength
Yield: .50 cu. ft./bag
MASTER BUILDERSEMACO® SBB-Cft REPAIR MORTAR
Part No.
MB80020
Standard Package
55lb.Bag
Skid Quantity
60 Bags
Flexible Cementitious Rebar Coating
DESCRIPTION:EMACO P22 is a polymer-modified cementitious based coating withRheocrete® 222 corrosion inhibiting admixture. This two component product provides protection for steel reinforcement in concrete against corrosion.
RECOMMENDED FOR:Protection of structural reinforcing steel that has been, or may be, subjectto corrosion and where a cementitious repair material will be applied.Applications include:• Horizontal, vertical or overhead repair where steel reinforcement is
present• Bridges• Water Treatment Facilities• Parking Garages• Tunnels• Marine Projects
FEATURES/BENEFITS:• Protects reinforcing steel against corrosion• Excellent adhesion to steel, concrete and mortar• Not a vapor barrier• Will not act as a bond breaker when applied on reinforcing steel or
surrounding concrete• High alkalinity level similar to concrete• Resistant to chloride and acidic gases such as CO2/S02
• Non toxic• High visibility color• Low electrical resistivity, unlike epoxy• Easy to apply to reinforcing steel with a medium hard brush• Excellent adhesion to cementitious repair mortars such as EMACO
Covers approximately 80 ft. of W' diameter NO.4 rebar when applied intwo coats to an overall thickness of approximately 80 mils.
Fast setting hydraulic cement
DESCRIPTION:EMACO 503 is a fast setting hydraulic cement designed to stop flowingwater through holes and cracks in concrete and masonry surfaces.
RECOMMENDED FOR:• Manholes• Sewer pipes• Tunnels• Basement and masonry cracks• Swimming pools• Floor and wall joints
FEATURES/BENEFITS:• Easy to use - just add water• Sets fast - approximately three to five minutes• Watertight repair - expands as it sets, giving excellent bond to
surrounding concrete• Compatible in appearance to concrete - requires no surface treatment• Durable - stronger than average concrete mixes used for the same
purposes
Yield: .5 cu. ft./pail
Sulfate and chloride-resistant one component cement-based repairmortar
DESCRIPTION:EMACO S66-CR is a rheoplastic, flowable repair mortar system. Itsunique formulation provides excellent bond, resistance to sulfates andchlorides, high electrical resistivity, very low permeability and high compressive strengths.
RECOMMENDED FOR:• Heavy-duty, durable, long-lasting repairs in corrosive environments• Interior and exterior environments• Horizontal and formed vertical and overhead applications• Marine structures, water and wastewater facilities and manholes• Bridges, tunnels, concrete pipe, parking structures and ramps• Chloride and sulfate exposure• Freeze/thaw environments• Repairs of one inch or greater in thickness
FEATURES/BENEFITS:• One component, easy to use• Shrinkage compensated• High slump design results in improved placement• Silica fume formulation provides a material with very low permeability• Good abrasion resistance• High strength• Good workability• Repair may be formed and poured - good pumpability
Yield: .43 cu. ft./bag
Part No.
MB60001
MASTER BUILDERSEMACO® 503 HYDRAULIC CEMENT
Standard Package
1 Gal. Kit
Part No.
MB66050
Standard Package
55 lb. Bag
Skid Quantity
60 Bags
Part No.
MB50350
Standard Package
50 lb. Pail
Skid Quantity
48 Pails..
880 MEEKER AVE • BROOKLYN, ,NY 1122286 Tel~ 718-387-0300 • FAX: 718-387-1874
MASTER BUILDERSEMACO® R300 PROFILING MORTAR
MASTER BUILDERSEMACO® R320 PATCHING MORTAR
MASTER BUILDERS EMACO® R310 PATCHING CEMENT
One component, polymer modified profiling mortar
DESCmpnON:Master Builders EMACO R300 is a one component, fast setting, polymermodified cement-based mortar ideally suited for leveling and/or resurfacing distressed concrete. EMACO R300 is designed for both interior andexterior use.
One component, polymer-modified, vertical/overhead patching mortar
DESCRIPTION:Master Builders EMACO R320 is a one component, polymer-modified,cement-based mortar ideally suited for patching and/or resurfacing distressed concrete. EMACO R320 is designed for both interior and exterioruse and can be applied by low pressure spraying or hand troweling. It canbe applied vertically in thickness from %" to 1W (6 to 38 mm), andoverhead from %" to 3/4" (6 to 19 mm).
RECOMMENDED FOR:• Vertical and overhead surfaces• Building facades• Balconies and columns• Beam and soffit repair• Bridges and parking decks• Retaining walls• General spalled areas• Tuckpointing
fEATURES/BENEfiTS:• One component, polymer-modified for easy mixing and handling• Very low permeability• Low modulus of elasticity for improved substrate compatibility• Sprayable for reduced labor requirements
Yield: .47 cu. ft./Bag.
APPLICATION THICKNESS:Vertical: Featheredge to 1 inch (25mm) per liftHorizontal: Featheredge to Y4 inch (6mm)
RECOMMENDED fOR:• Vertical surfaces• Pedestrian horizontal areas• Smoothing rough surfaces• Repair of bugholes and honeycombs
fEATURES/BENEATS:• One component· easy mixing and handling• Excellent workability/finishability• Very low permeability• Fast strength gain for quick turn around• Ready for foot traffic after 6 hours• Suitable for skim coats
Yield: .45 cu. ft. per 55 lb. bag
Part No. Standard Package
MB10075 55 lb. Bag
Skid Quantity
60 Bags
Part No.StandardPackage
SkidQuantity
MASTER BUILDERSEMACO® R350 VERTICAL/OVERHEAD MORTAR
One component, polymer-modified patching mortar
DESCRIPnON:Master Builders EMACO R310 is a one component, fast setting, polymermodified cement-based mortar ideally suited for patching and/or resurfacing distressed concrete. EMACO R310 is designed for both interiorand exterior use.
MB10090 55 lb. Bag 60 Bags
Yield: .45 cu. ft./bag neat, .63 cu. ft. when extended with 25%%"pea gravel.
fEATURES/BENEFITS:• One component - easy mixing and handling• Very low permeability• Fast strength gain for quick turn around• Ready for foot traffic after 6 hours• Abrasion resistant
APPUCAnON THICKNESS:Horizontal: Y4 inch to 1 inch
w/o aggregate extension1 inch to 3 inchwith aggregate extension
RECOMMENDED FOR:• Horizontal surfaces• Walkway aisles• Work areas• Rough floors• Ramps and steps• Bridge and parking decks• Utility areas• Balconies
One component, polymer-modified lightweight vertical/overhead mortar
DESCmPnON:Master Builders EMACO R350 is a one component, polymer-modifiedcement-based mortar ideally suited for patching vertical or overheaddistressed concrete. EMACO R350 is designed for both interior andexterior use.
60 Bags
SkidQuantity
StandardPackage
55 lb. Bag
Part No.
MB10055
APPLICATION TIICKNESS:Vertical/Overhead: Featheredge to 2% inch per lift
RECOMMENDED FOR:(Vertical and overhead surfaces)• Soffit repairs• General spall areas• Tuckpointing• Balconies and columns
FEATURES/BENEFITS:• One component - easy mixing and handling• Excellent workability/finishabillity• High build capability• Ready to use - just add water
Yield: .65 cu. ft./bag
60 Bags
Skid Quantity
55 lb. Bag
Standard Package
MB50055
Part No.
1 SOUTH SECOND ST. • PEER PARK, NY 11729Tel: 631-242-8555 • FAX: 631-667-8869 87
MASTER BUILDERSMASTERSEAL® 510 CEMENTITIOUS COATING
MASTER BUILDERSMASTERFLOW® 928 GROUT
Yield: One 55 lb. bag when mixed with 1.45 gals. of water will yield 4 gals.of mixed material and will cover approximately 200 sq. ft. at 31 mil.thickness.
One component, polymer-modified cementitious protective coating
DESCRIPTION:Master Builders MASTERSEAL 510 is a one component, polymermodified, cement-based protective coating designed for waterproofing,dampproofing and beautifying concrete, mortar and masonry.MASTERSEAL 51 0 can be used for both interior and exterior applications.
RECOMMENDED FOR:• Newly repaired concrete to provide a uniform color and appearance• Architectural coating to beautify concrete• Positive side waterproofing and dampproofing of uncracked concrete• Vertical and overhead surfaces• Carbonation protection of concrete
FEATURES/BENEFITS:• Waterproofs and dampproofs surfaceso Attractive, decorative appearance• Increases resistance to deicing salts and CO2
• Protects concrete surfaces from environmental influences
MASTER BUILDERSMASTERSEAL® 550 WATERPROOF COAnNG
High-precision, nonshrink, natural-aggregate grout
DESCRIPTION:MASTERFLOW 928 grout is specially formulated for use at any consistency-from fluid to damp-pack-for grouting machines or plates requiringprecision-bearing support. This ready-to-use product meets the volumechange and exceed the compressive strength requirement of CRD-C621,Corps of Engineers Specification for Nonshrink Grout and ASTM C-1107at fluid consistency.
RECOMP.l:NDED FOR:• Precision grouting of eqUipment and machinery, baseplates,
soleplates and columns• Grouting applications where shrinkage must be eliminated and where
a high-strength grout, similar in appearance to concrete and mortar,is desired
• Applications where high, one-day and later-age compressivestrengths are required
• Non-shrink grouting of precast wall panels, beams and columns,curtain walls, concrete systems, and other structural andnonstructural building members
• Repairs to concrete, such as filling rock pockets and large cracks• Applications calling for a grout to be pumped
FEATURESjBEIIIRTS:• Hardens free of bleeding, settlement or shrinkage when mixed,
placed and cured at almost any consistency-fluid (25 seconds ormore), flowable, plastic or damp-pack
• Contains carefully graded, high-quality quartz aggregate for optimumstrength and workability
Yield: .5 cu. ft./bag
60 Bags
Skid Quantity
55 lb. Bag
Standard Package
MB92855
Part No.
60 Bags
Skid Quantity
55 lb. Bag
Standard PackagePart No.
MB51055
Flexible, cementitious coating for waterproofing and protection
DESCRIPTION:Master Builders MASTERSEAL 550 is a ready-to-use, flexible, polymermodified cementitious-based coating designed for waterproofing andprotecting concrete, mortar and masonry surfaces. MASTERSEAL550 isused for both interior and exterior applications where positive or negativeside waterproofing is reqUired. MASTERSEAL 550 can be applied by lowpressure spraying or hand troweling.
RECOMMENDED FOR:• Positive and negative side waterproofing• Protection of cementitious surfaces• New and repaired concrete to provide a uniform color and
appearance• Architectural coating for aesthetic enhancement
TYPICAL USES:• Water reservoirs, tanks and containers• Basements• Building facades• Balconies and precast elements• Bridges• Retaining walls• Parking structures
Yield: One unit consisting of 1.5 gal. liquid polymer and 551bs. of powderwill yield approximately 4 gals. and will cover approximately 220 sq. ft. at31 mil. thickness.
MASTER BUILDERS MASTERFLOW® 713 GROUTHigh-precision, nonshrink, natural-aggregate grout
DESCRlPDON:Masterflow 713 grout contains specially graded, natural aggregates andis formulated to be used at any consistency from fluid to damp-pack. It isrecommended for applications requiring precision support where earlyform stripping and/or shoulder trimming are required. Where early formremoval is not required and extended working time is needed, Masterflow928 grout offers extended working time and higher ultimate strengths.
RECOIWlJlEI'IJED FOR:• Applications where shrinkage must be eliminated and where a grout
similar in appearance to concrete and mortar is desired• Precision equipment, baseplate, soleplate and column grouting• Grouting precast wall panels, beams and columns, concrete systems,
structural building members and curtain walls
FEATURES/BENEATS:• Can be pumped into intricate areas or into areas inaccessible by
conventional grouting methods• Provides shrinkage compensation through the expansion of hydrating
mineral components• Meets all of the requirements of CRD-C 621, Corp. of Engineers
Specification for Nonshrink Grout and ASTM-C 1107
Yield: .52 cu. ft./bag; more or less water may be necessary to meetconsistency requirements thus increasing or decreasing the yield.
Part No. Standard Package Part No. Standard Package Skid QuantityMB80030 68 lb. Kit MB71355 55 lb. Bag 60 Bags
880 MEEKER AVE • BROOKLYN, NY 1122288 Tel: 718-387-0300 • FAX: 718-387-1874
General construction, natural aggregate, non shrink grout
DESCRIPTION:CONSTRUCTION GROUT is a non-catalyzed, multi-purpose construction grout containing mineral aggregate. This portland cement-basedproduct is designed to meet all of the performance requirements of theCorps of Engineers Specification CRD-C 621-89 at a flowable or plasticconsistency.
RECOMMENDED FOR:• Normal loads for columns and baseplates• Anchoring bolts, reinforcing bars and roadway dowels• Bedding grout for precast panels• Repairing of cavities resulting from ineffective concrete consolidation• Caulking concrete pipe• Backfilling, underpinning foundations and pressure grouting of slabs
needing alignment• General construction applications• Dry pack applications
FEATURES/BENEmS:• Free of inorganic accelerators, inclUding chlorides or other salts
detrimental to reinforcing steel• Color similar to concrete after curing• Can be extended with clean, well-graded coarse aggregate to fill
large voids without additional mix water• Hardens free of bleeding when placed at a plastic or flowable
consistency and when ambient temperatures are 50°F (10°C) andabove; yield: A 50 lb. bag mixed to a flowable consistency will yield.45 cu. ft.
FLOOR TOPPINGS
60 Bags60 Bags60 Bags
SkidQuantity
StandardPackage
50 lb. Bag50 lb. Bag55 lb. Bag
Description
Underlayment 110Topping 112Anvil Top-300
Part No.
MB10030MB10035MB10038
Performance
Product Description Aggregate Wear Resistance ImpactType Light Heavy Resistance
Underlayment 110 Self-leveling cementitious Mineralfloor underlaymenl.
Topping 112 Flowable!leveling polymer- Mineral •modified topping.
Anvil,Top@300 Heavy,duty industrial floor Metallic • •topping.
PRODUCT COMPARISON
PLACEABILI1Y
111111IIII~IMaster Builders
Technologies
Anvil-Top® 300, Underlayment 110 and Topping 112
FIELDS OF APPLICATION:Master Builders cementitious toppings include self-leveling underlayments and overlayments as well as heavy-duty toppings for use in a variety of installations, such as:• Offices, hospitals, and other commercial applications• Utility areas, light-duty warehouse floors• Industrial aisleways, work areas and loading docks• Waste transfer stations• Truck or tractor repair areas• Other heavy abrasion areas
SkidQuantity
StandardPackage
CONSTRUCTION GROUT
Part No.
111111IIII~IMaster Buildersl€chnologies
For exterior and interior use, Weld-Crete® will bond new concrete, portland cement plaster, and cementitious mixes to structurally sound concrete floors, walls, columns, beams, steps and ramps.
It can be "painted on" in asingle application 1to 10 days prior to concreteplacement.
Use Weld-Crete's open time to your advantage in bonding to concreteshear walls, where you need a time lapse between application of bondingagent, placement of reinforcing steel, placement offormwork and placement of concrete.
Weld-Crete® is also used for bonding setting beds for ceramic tile and forbonding portland cement plaster and stucco mixes; and to bond to suchsurfaces as brick, block, tile, marble, metal, glass block, soundly adheredpaint (non-soluble in water), and silicone.
WELDDCRETE BONDING AGENT
MB70050 50 lb. Bag 60 Bags Topping Self Leveling!Product Depth Pumpable Leveling Screedable
Underlayment Up to %" without III .110 extension
Topping 112 Up to %" without 0 0
extension
Anvil-Top® 300 1/2" and up • •
Part No. Size Skid Qty.
WC10005 5 gal. Pail 36
1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631-242-8555 • FAX: 631-667-8869 89
MASTER BUILDERSCEILCOTE® 848 CP PLUS EPOXY GROUT
MASTER BUILDERSMASTERSEAL®SL 40 PENETRATING SEALER
t t.t••iiiiiiiii.. ..•.....• •.: ····m
ISonneborrilKURE-N-SEAL W-WATER-BASED CUREA transparent water-based curing, sealing and dustproofing compoundfor freshly placed and aged concrete. VOC compliant meets the requirements of ASTM C309.
High strength, high temperature, high flow epoxy groutDESCR.TION:Ceilcote 648 CP Plus represents the continued evolution and improvement of the Ceilcote series since the original introduction of Ceilcote 648in 1956.RECOMMENDED FOR:• Precision alignment of machinery, compressors and prime movers inthe gas transmission and other industries
• Application requiring fast turnaround with high early and seven daycompressive strengths
PACKAGING:2161b. Full Unit (1.73 ft3, 0.05 m3)
Ceilcote 648 CP Plus Liquid 1 - 20.2 lb. pail (10.06 kg.)Ceilcote 648 CP Plus Hardener 1 - 7.6 lb. bottle (3.4 kg.)Ceilcote 648 CP Plus Aggregate 4 - 47 lb. bags (21.3 kg.)
54.4 lb. Unit (0.43 ft3, .012 m3)Ceilcote 648 CP Plus Liquid 1 - 5.1 lb. pail (2.3 kg.)Ceilcote 648 CP Plus Hardener 1 -1.9Ib. bottle ( .9 kg.)Ceilcote 648 CP Plus Aggregate 1 - 471b. bag (21.3 kg.)
(54 lb. unit is shipped in a 5 gallon pail over-pack)
Silane penetrating sealer
DESCRIPTION:MASTERSEAL SL 40 is a one component, alkylalkoxy silane penetrantforpreventing the intrusion of water and water-borne salts into concrete andmasonry substrates. This product is suitable for use on old and new, fullycured concrete. It will protect all types of concrete and masonry substrates, including precast and prestressed concrete, brick, mortar, andstucco. It is particularly well suited for traffic surfaces and architecturalsurfaces where color and texture should not be altered.
RECOMMENDED FOR:• Bridge Decks• Highways• Parking Structures• Horizontal and Vertical Surfaces
FEATURES/BENEATS:• Very low viscosity for high penetration• Long-term protection from water and salts• Chemically bonds to concrete• Permeable to water vapor - Allow structure to breathe• Does not darken, stain or gloss concrete surfaces
COVERAGE RATES: 125 to 200 sq. ft. per gallon depending onconditions
Part No.
MB10020MB10025
StandardPackage
54.4 Lb. Unit216 Lb. Unit
Yield
.43 Cu. Ft.1.73 Cu. Ft.
Part No.
MB49105MB49155
StandardPackage
5 Gal. Pail55 Gal. Drum
Part No.StandardPackage
SkidQuantity
SON40040SON40045
5 gal. Pail55 gal. Drum
36 Pails
BOND BREAKER TAPE
Sonolastic 200 Adhesive is a rubber-base, solvent-carried adhesive forbonding most rigid foam insulation, including polystyrene and urethane,to themselves orto structurally sound surfaces such as concrete, masonry, wood, metal, gypsum board, asbestos cement board, and composition board. It is excellent for bonding gypsum wallboard or paneling tostuds or furring strips.
SONNEBORN® 200 ADHESIVE
ISonnebornl
2412
PerCarton
StandardPackage
300 ml. Cartridge825 ml. Cartridge
SON20010SON20016
Part No.
Width Case(in.) Qty.
V4 2880/8 192~ 144% 967/8 781 72
1V2 482 36
A horizontally oriented polypropylene filmcoated with a high performance acrylic adhesive that adheres well in both hot andcold weather. Can be applied in temperatures ranging from 32°F to 150°F and willoperate in temperatures ranging from O°Fto 200°F. Normally supplied in transparentbut also available in black, orange or white.
Part No.
BBT10014BBT10038BBT10012BBT10034BBT10078BBT10100BBT10112BBT10200
880 MEEKER AVE • BROOKLYN, NY 1122290 Tel: 718-387-0300 • FAX: 718-387-1874
ISonneborrilEPOFIL EPOXY INJECTION
ISonneborrilSONNEBORN® Np·l CAULKING
ISonneborrilSONOBLOCK CEMENT BASED WATERPROOFINGA cement-based waterproof coating for walls and overhead masonry.Sonoblock fills, seals, waterproofs, and protects masonry against bothpositive and negative hydrostatic pressure. It can be applied above orbelow grade, interior or exterior.
COVERAGE:
A two-component high-modulus low-viscosity epoxy injection resin.EpoFil is used for the high-strength bonding of cracks. It can be appliedmanually or by automated injection systems; use it to grout bolts andpins, and as an epoxy mortar system when mixed with over-dried aggregate. EpoFil is also available in a super-low viscosity version. 3 gallon kitsconsist of 2 gallons of resin and 1 gallon of hardener.
First Coat: 225 to 250 sq. ft. per 50 Ibs.Second Coat: 300 to 350 sq. ft. per 50 Ibs.
303030303030303030
StandardCarton
StandardPackage
11/2 gal. Kit
* Other colors available on request.
Part No.
SON20125
SON10001 300 ml. Cartridge LimestoneSON10002 300 ml. Cartridge WhiteSON10003 300 ml. Cartridge BlackSON10004 300 ml. Cartridge TanSON10005 300 ml. Cartridge Aluminum GraySON10006 300 ml. Cartridge Med. BronzeSON10007 300 ml. Cartridge StoneSON10008 300 ml. Cartridge Off WhiteSON10009 300 ml. Cartridge Redwood Tan
Two component polyeurethane sealant. Movement capability of ± 50%.Extraordinary adhesion and cohesion. Long lasting. Bonds without primer. Color pigments available in a wide variety of colors.
Moisture curing high performance polyurethane sealant. Requires nomixing. Bonds to many materials, including concrete, masonry, aluminum and wood without a primer. Available in a variety of colors.
StandardPart No. Package *Color
ISonneborrilSONNEBORN® NP2 CAULKING
SkidQuantity
3 gal. Unit
Standard Package
StandardPackage
SON40001
Part No.
Part No.
SON40010SON40015
50 lb. Pails501b. Bags
3650 ISonneborril
SONNEBORN® SL-1 CAULKING
A one-component moisture-curing bitumen-modified polyurethane.HLM 5000® forms a seamless elastomeric water-proofing membrane forexterior below-grade or between-slab applications. It protects againstthe penetration and lateral movement of water. Available in 4 grades forapplication by trowel, squeegee, roller and spray.
ISonneborrilHLM5000® AN ELASTOMERIC WATERPROOFING
* 55 Gal. Drums available on special order basis.
COVERAGE:
Wet Mil Thickness
3012
CaseQty.
11/2 Gal. Kit
Color
LimestoneLimestone*Limestone*
Standard Package
* Also available in Gray.
SON20130
StandardPart No. Package
SON10030 300 ml. CartridgeSON10032 825 ml. CartridgeSON10035 2 Gal. Pail
Part No.
One part self leveling polyeurethane sealant for expansion joints inconcrete joints and decks. It is non priming and requires no mixing. It issimply poured in place and cures to form a resilient tough seal.
Sonolastic SL 2 Sealant is a two-component sealant designed for expansion joints in concrete floors and decks. It is available in a self-levelingformula as well as a slope-grade version. After mixing, SL 2 is poured orgunned in place. It cures to form a tough, resilient joint seal. It can becolored by adding pigments available in a wide range of colors.
ISonneborrilSONNEBORN® SL2 CAULK
Pkg. SkidSize Qty.
5 Gal.* 365 Gal. 365 Gal.* 365 Gal.* 36
25 to 30 sq. ft. per gallon25 sq. ft. per gallon
Coverage
Description
HLM 5000 SL Self LevelingHLM 5000 T Trowel GradeHLM 5000 S Spray GradeHLM 5000 R Roller Grade
SON40120SON40121SON40122SON40123
5560
Part No.
1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631-242-8555 •. FAX: 631-667-8869 91
ISonneborrilACRYLIC ADDITIVE LIQUID EMULSION
!SonneborrilSONOCRETE SCREED MORTAR
An acrylic-latex-base liquid emulsion with cement mortars and patching compounds. Acrylic Additive improves the strength and adhesion of materials used inthe general repair and restoration of concrete.
A screedable mortar designed for the repair of deteriorated concrete floors, balconies, and industrial facilities. Can be extended with aggregate for "form and pour"deep repairs. One component, polymer modified for high abrasion resistance andlow chloride permeability. Yields: .45 cu. ft. neat, .55 cu. ft. when extended with20 Ibs. of coarse aggregate.
Part No.
SON30001
StandardPackage
5 gal. Pail
SkidQuantity
36 Part No.StandardPackage
SkidQuantity
A low-odor epoxy/cement adhesive used as a bonding agent for concrete repairsand an anti-corrosion agentforthe protection of rebar. Sonoprep is VOC compliant.Kit consists of 1 gal. jug part A and 32 lb. bag part B. Yields 2.7 gallons. Covers150-160 sq. ft. per gallon.
ISonneborriISONOPATCH 100 TWO COMPONENT MULTI·PURPOSE REPAIRMORTAR
ISonneborrilSONOPREP EPOXY CEMENT ADHESIVE
Nonsag single component repair mortar. Can be placed on vertical or overheadsurfaces in lifts up to 2 inches deep without forming and excellent workability.Structural strength exceeds 6000 psi. 43 lb. bag yields .50 cu. ft.
48 Bags
48 Bags
SkidQuantity
StandardPackage
43 lb. Bag
50 lb. Bag
Part No.
SON30050
SON30060
ISonneborrilSONOGROUT NOMETALLIC GROUT
ISonneborrilSONOCRETE GEL PATCH
50 Bags
SkidQuantity
StandardPackage
2.7 gal. Kit
Part No.
SON30010
General purpose repair mortar, can be featheredged. Fast Setting: foot traffic in 24hours. Can be used above or below grade. High compressive strength. Yields:.4 cu. ft. neat, .46 cu. ft. when extended with 151bs. of coarse aggregate.
Shrinkage-compensated, nonmetallic, high-strength grout. Sonogrout 10K is ahighly reliable product complying with Corps of Engineers CRD-C-621-83. Onecomponent. Flowable. 50 lb. bag yields .40 cu. ft .
Part No.
SON30020
StandardPackage
1 gal. + 42 lb. Bag
SkidQuantity
48 Kits
Part No.
SON30070
StandardPackage
50 lb. Bag
SkidQuantity
50 Bags
Use for horizontal applications where excellent adhesion, superior abrasion resistance, and high ultimate strength is desirable. Rapid strength gain. High compressive strength. Stands up to heavy traffic. Yields: .4 cu. ft. neat, .50 cu. ft. whenextended with 151bs. of coarse aggregate.
Fast setting mortar for horizontal, vertical and over-head applications. Rapidstrength gain. Does not sag or slump. Can be molded and shaved. Use above orbelow grade. Yields: .4 cu. ft. neat, .54 cu. ft. when extended with 151bs. of coarseaggregate.
ISonneborriISONOPATCH 200 TWO COMPONENT VERTICAL I OVERHEADREPAIR MORTAR
ISonneborriISONOPATCH 300 POLYMER HORIZONTAL REPAIR
StandardPackage
2 gal. Unit
Part No.
SON30080
A two-component epoxy bonding and grouting adhesive. EpoGrip can be used tostructurally bond plastic concrete to hardened concrete, to set anchoring bolts, orto gravity-feed cracks. Complies with ASTM C 881. 2 Gallon unit consists of 1 gallonof resin and 1 gallon of hardener. 1:1 mix ratio. Coverage: Approx. 80 sq. ft./pallon at20 mils on smooth concerete.
A two-component high-strength and high-modulus nonsag epoxy gel adhesive.EpoGel seals cracks and sets injection ports before pressure injection, grouts boltsand pins in horizontal and overhead applications, grouts cracks in static structuralconcrete, and acts as a structural adhesive for bonding to concrete and masonry.2 Gallon Kit consists of 1 gallon of resin and 1 gallon of hardener. 1:1 mix ration.
ISonnebornIEPOGEL EPOXY GEL ADHESIVE
ISonneborrilEPOGHIP EPOXY BONDING .. GROUTING ADHESIVE
48 Bags
SkidQuantity
Size
1 gal. + 52 lb. BagSON30030
Part No.
Part No.StandardPackage
SkidQuantity Part No.
StandardPackage
SON30040 1 gal. + 1 43 lb. Bag 48 Bags SON30090 2 gal. Unit
880 MEEKER AVE • BROOKLYN, NY 11222 '92 Tel: 718-387-0300 • FAX: 718-387-1874
A single component silicone firestop sealant. Meets ASTM E814 and UL 1479. ltis aself leveling material. It is well suited for fire stopping gaps between perimeter offloor slab and exterior walls. The flexibility of Biotherm 200 compensates formechanical movement of pipes, conduits, electrical cables, expansion joints andwall/floor junctions. Yields: Tubes, 18.3 cu. in.; Pails, 1220 cu. in.
~
BIOTHERMe 200ISonneborrilFLEXCOAT ACRYLIC EMULSION COATING
A high-built acrylic emulsion coating for use on exterior block, brick, concrete, andstucco. Resists wind-driven rain but also provides a breathing film allowing vapor toescape from beneath the coating without loss of adhesion. It will not become hard orbrittle even after many years of exposure. Complies with Federal SpecificationIT-C-555B, Type II. Available in smooth and textured finishes in 14 standard colors;color matching is available on special orders. VOC compliant.
BIOTHERM 200 ARESTOP SHIELD
(If I~
Part No.StandardPackage
SkidQuantity Part No.
StandardPackage
Box/SkidQuantity
Bio Fireshield Firestop Systems are used to maintain the integrity of fire resistiveconstruction designed to contain smoke, toxic gasses and fire. All Bio Fireshieldproducts are free of asbestos, solvents and PCB's; all products are envi ronmentallysafe.
45 Bags
SkidQuantity
Box/SkidQuantity
15 Tubes per Carton6 Pails per Carton18 Pails per Skid
12 per Carton
15 Tubes per Carton45 Pails per Skid
18.3485122036.6
Yield(cu. in.)
StandardPackage
44 lb. Bag
10.15 oz. Tube5.28 gal. Pail
StandardPackage
10.15 oz. Tube2.10 gal. Pail5.28 gal. Pail
20.3 oz. Sausage
BFS90044
BFS50010BFS50020BFS50030BFS50040
Intumescent firestop caulk, water based: Remains flexible. Meets ASTM E814 andUL1479. It is used to firestop insulated metal pipe and non insulated metal pipewherein movement of pipe does not require elongation of a silicone firestop sealant.Use for construction joints between top of fire rated wall and underside of floorabove.
BFS20100BFS20110
Part No.
Novasit K-10 is a non-asbestos, 47-57 pounds per cubic foot air dried densityPortland Cement fly ash through-penetration firestop mortar.
Novasit K-10 Firestop Mortar's unique physical properties provide for easy installation and repenetration. Little or no damming or forming is required. It adheresto concrete, masonry, galvanized steel and most common through-penetrationmaterials.
Novasit K-1 0 Firestop Mortar is UL classified for both Flame (F) and Temperature (T)ratings under ASTM E 814-83 (UL 1479). Classifications include zero clearance(space between through-penetration and openings in fire resistive wall or floor) and100 percent visual cable loading. Tested in wall openings of up to 55 square feet andin floor openings up to 30 square feet. UL Classified per UL System Nos. WK4003,CBJ4006, WL0001, WL1011, WL1012, CAJ0033, CAJ1032, CAJ2014, CAJ3024,CAJ5006, CAJ8005. Yield: 1240 cu. inches bag.
Part No.
K-10 FIRESTOP MORTAR
HIOSTOP 500 FIREITOP CAULK
(I' BiOSTOP' 500+ I~ /Eo
1212121
Case Quantity
36 Pails
Box/SkidQuantity
15 Tubes per Carton18 Pails per Skid
5 gal. Pail
StandardPackage
10.15 oz. Tube5.28 gal. Pail
ARE STOPPING PRODUCTS
Part No. Description
SON40030
Part No.
BSF10010BFS10020
TOD11101 750ml Gun Foam CanTOD11102 600ml Gun Foam CanTOD11106 600ml Self Dispensing Foam CanTOD11104 Dispensing Gun
A single component silicone firestop available in tubes. Meets ASTME814 and UL1479. It is a gun grade. It is well suited for firestopping gapsbetween perimeter of floor slabs and exterior walls. The flexibility ofBiotherm 100 compensates for mechanical movement of pipes, conduits, electrical cables, expansion joints and wall/floor junctions. Yields:Tubes, 18.3 cu. in.; Pails, 1220 cu. in.
High yield foam sealant is ideal fora variety of applications includingconcrete block filling, conduit andchase filling and sealing, damningfor firestop material, asbestosabatement containment and awide variety of uses around construction sites. Safe - No Urea Formaldehyde and no CFC's.
Available in two styles: self dispensing cans or gunable cans. Self dispensing cans are quick and easy to use and require no special tools.Gunable cans can be reused after initial dispensing.
EXPANDING FOAM SEALANT
BIOTHERM 100 FIRESIOP SEAL
(\--'_B_IO_'T_H_ER_M_e
_10_0-JI~--.....-&::>
1 SOUTH SECOND ST. • DEER PARK, NY 11729 'Tel: 631-242-8555 • FAX: 631-667-8869 93
SAND MIXA mixture of Portland Cement, washed and graded sand and gravel. Forrepair and building jobs where concrete thickness exceeds 2". Ideal forpouring footings, anchoring poles and posts, and building curbs, walks,drives and steps. Exceeds ASTM C387.
SAKRETE® BLACKTOP MIXA blend of steam cured asphalt and graded aggregates. Can be used tobuild or repair any blacktop area. Simply place right as it comes from thebag in 1" layers and tamp firmly. Specifically designed for pothole applications.
Part No.
AS40080
Description
Sand Mix - 80 lb. Bag
Skid Qty.
42 Part No.StandardPackage
SkidQuantity
AS00071 60lb.Bag 56
SAKRETE® MORTAR MIX BLACKTOP SEALERA mixture of masonry mortar cement and graded bank sand. Especially designedfor laying brick, block or stone. Can be used to repair masonry or used as a stucco.Exceeds ASTM Specification C 387.
Lowest price driveway sealer. Offers good bonding and ajet black finish.
Part No.Avg CompStrength
StandardPackage
SkidQuantity
Part No.
AS00091
StandardPackage
5 gal. Can
SkidQuantity
36
AS00039 4000 PSI 80 lb. Bag 42 Bags AMSTONE® FILLED SEALER
Competitively priced grit-filled tar pitch emulsion that beautifies andprotects blacktop surfaces, improves wearability and provides additionaltraction.
TYPE NMASONRY CEMENT
• Industry standard• High degree of plasticity for bonding• High compressive strength• For structural applications Part No.
StandardPackage
SkidQuantity
CLOSED CELL BACKER RODPart No.
AS30070
StandardPackage
70 lb. Bag
SkidQuantity
40
AS00567 5 gal. Can 36
High quality Portland cement. Excellent in parging block or concrete basementwalls. Improve a low grade cement mix, or use with sand and gravel to custom mix.
~S;T, #1200 WHITE WATERBASE CURING~ COMPOUND
CQI~-::i~ SEALTIGHT 1200-WHITE Water-Base ConcreteCuring Compound is resin-base dispersion with se
lected white pigments. Formulated to retain a minimum of 95% of themoisture in freshly placed concrete for 72 hours to allow completecement hydration. The white pigment will reflect heat producing rays ofthe sun thereby helping to keep the concrete surface cooler and preventing excessive heat build-up, which can cause thermal cracking.
USECompounded specifically for Federal, State and MunicipalHighway and Airport paving projects.
SPECIFICATIONSASTM C-309, Type II, Class BAASHTO M-148, Type 11, Class B
PORTLAND CEMENT TYPE II
Primer 733 is a transparent solvent-based product for priming masonryjoints and other recommended substrates before the application ofSonneborn urethane sealants.
Coverage35-40 sq. ft. per pint (6.87-7.86 m2/L) or approximately 450 linear feet(137 m) for a W' (12.7 mm) deep joint.
Std. Pack (ft.)
40003200250015501100550400420240
1 Pint
StandardPackage
Diameter (in.)
%3/8
V25/8
31411%1V22
SON90016SON90024SON90032SON90040SON90048SON90064SON90080SON90096SON90128
SON73300
Part No.
Closed Cell Backer-Rod is a resilient polyethylene foam designed forcold-applied joint sealants. Sealants do not adhere to Closed-CellBacker-Rod, which becomes an integral part of the joint sealing system.Used as a back-up material, Closed-Cell Backer-Rod provides the propershaping of the sealant while permitting it to stretch and recover with jointmovement. Closed-Cell Backer-Rod is extruded to various diameters toaccommodate a range of joint widths.
Part No.
ISonneborrilPRIMER 733
42
SkidQuantity
36 Pails4 Drums
SkidQuantity
StandardPackage
94 lb. Bag
StandardPacking
5 gal. Pail55 gal. Drum
Part No.
AS20044
WRM12005WRM12055
Part No.
880 MEEKER AVE • BROOKLYN, NY 1122294 Tel: 718-387-0300 • FAX: 718-387-1874
RAPID SET® DOT CEMENT RAPID SET® NON SHRINK MORTAR MIX
Rapid Set® O.O.T. Cement is aspecially formulated blend of Rapid Set®Cement and other ingredients. Rapid Set® D.O.T. Cement should bemixed with local concrete sand and stone at a 1-2-2 ratio (cement, sandand stone). This unique formulation produces a high quality repair material with excellent durability that achieves high early and ultimate strengthwith zero shrinkage and excellent durability. The development of highearly strength provides conformance with CRD-C-621 in only 3 hours.
Ideal for the repair of highways, bridge decks, airport pavement,industrial floors, parking garage decks, and freezer floor.
Compressive Strength ASTM C 39/C 109
1 Hour 3 Hours 24 Hours 28 Days
3,140 3,725 4,650 5,500Rapid Set® O.O.T. Cement is packaged in 50 Ibs. bags. When properlymixed, it will yield approximately 2 cu. ft.
Rapid Set® Non-Shrink Mortar Mix is a unique dry packaged blend ofRapid Set® Cement and a quality sand. Rapid Set® Non-Shrink MortarMix does not expand or shrink and does not contain chloride. Whenmixed with water, it provides a quality grout which attains 2,000 psicompressive strength in one hour after placement. Rapid Set® NonShrink Mortar is similar in color to porland cement concrete.
Precision grouting under machine bases and columns, grouting of anchor bolts, rebar and railing and for the repair of precast concrete,industrial floors, highways, runways and sidewalks. Rapid Set® NonShrink Mortar is also excellent for vertical and overhead repairs. Thisproduct may be extended by adding up to 60% by weight of %" stone.
Yield: A 55 lb. bag will yield .50 cubic ft. and extended with stone will yield.80 cubic ft.
Compressive strength, psi (ASTM C 109)
Part No. Description Skid Oty. 1 Hour 24 Hours 7 Days 28 Days
RS10050 Rapid Set DOT Cement 50 lb. Bag 562,000 6,600 7,000 7,600
Part No. Description Skid Qty.
RS40050 Rapid Set Non Shrink Mortar Mix 55 lb. Bag 50
RAPID SET® DOT REPAIR MORTAR
Rapid Set® D.O.T. Repair Mortar is formulated with a special sand andRapid Set® Cement. This unique formulation produces a high qualityrepair material with excellent durability that achieves high early andultimate strength. The development of high early strength provides conformance with CRD-C-621 in only 3 hours.
Ideal for the repair of pavement, bridge decks, industrial floors, parkinggarage decks, freezer floors and vertical and overhead repairs.
Yield: Rapid Set® O.O.T. Repair Mortar is packaged in 50 lb. bagsyielding approximately 112 cu. ft. When extended with 45 to 50 Ibs. aggre- RAPID SET® NON SHRINK MULTI PURPOSE GROUTgate, yields approximately % cu. ft.
Compressive Strength ASTM C 39/C 1091 Hour 3 Hours 4 Hours
3,140 3,725 4,650
Part No.
RS30050
Description
Rapid Set DOT Repair Mortar 50 lb. Bag
8 Hours
5,500
Skid Oty.
56
Rapid Set® Non-Shrink Multipurpose Grout Cement AIJTM is a uniquedry blend of Rapid Set® Cement and a quality sand. NO CHLORIDESARE ADDED. This is a high quality product. When mixed with water, itproduces a uniform, nonshrink mortar which can be featheredged. Itattains over 2000 psi compressive strength in one hour, and is ready foruse.
RAPID SET® CONCRETE MIX
Precision grouting under columns, machine base plates, and precastrepair. Grouting of anchor bolts, rebar and railing. Excellent for floorrepair and leveling. Rapid Set® Non~Shrink Multipurpose GroutCement AWM is ideal for all applications where quick concrete strength isrequired, including repair of highways, runways, sidewalks and floors.
50
Skid Oty.
11,4 gal. water
27003700440064007400
Description
RS50550 Rapid Set Non Shrink Multi Purpose Grout-Extra HighStrength-55 lb. bag
Part No.
Yield:When mixed with 3/4 gal. of water: .46 cu. ft./55 lb. bag.When mixed with 1114 gal. of water: .50 cu. ft./55 lb. bag.
Compressive strength, psi (ASTM C 109)3;4 gal. water
4800500052008200
11,200
1 hour3 hours1 day7 days28 days
50
Skid Oty.
28 Days
6300
Description
Rapid Set Concrete Mix 60 lb. Bag
Part No.
RS2oo60
Rapid Set® Concrete Mix is a unique dry packaged blend of hydrauliccement, sand and gravel (nominal %"). NO CHLORIDES ARE ADDED.When mixed with water, it produces a quality concrete which attains 2000psi compressive strength in one hour. Rapid Set® Concrete is similar incolor to Portland Cement concrete.
Ideal for applications where qUick strength is required, including patching highways, runways, sidewalks and floors.
Compressive strength, psi (ASTM C 192)1 Hour 24 Hours 7 Days
2000 4200 5100
1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631-242-8555 • FAX: 631-667-8869 95
FIVE STARGROUT
FIVE STARINSTANT GROUT
A premium all purpose grout for setting equipment, structural columns, anchorbolts and precast work.
Typical Compressive Strengths at 73°F. ASTM C 109*
Rapid-strength-gain grout for four hour machinery start-up and cold weather grouting.
Typical Compressive Strengths at 73°F. ASTM C 109*
4 Hours1 Day3 Days7 Days28 Days
* modified
MIN. WATERPSI (MPa)
xxx4,000 (27.6)6,200 (42.8)7,000 (48.3)8,600 (59.4)
MAX. WATERPSI (MPa)
xxx2,500 (17.3)4,700 (32.4)5,500 (37.9)6,500 (44.8)
4 Hours1 Day3 Days7 Days28 Days
• modified
MIN. WATERPSI (MPa)
4,500 (31.1)7,000 (48.3)8,000 (55.2)8,500 (58.7)9,000 (62.1)
MAX. WATERPSI (MPa)
4,000 (27.6)5,000 (34.5)7,000 (48.3)7,500 (51.8)8,000 (55.2)
A horizontal repair material. Rapid setting. Approved NYC DOT 701.04,701.09.
TYPICAL PHYSICAL PROPERTIES*Compressive Strength, ASTM C 109:
2,500 psi (17.2 MPa)3,000 psi (20.7 MPa)
56 Bags56 Bags
SkidQuantity
2000350040005000
StructuralConcrete via
PSI (MPa)
56 Bags
SkidQuantity
StandardPackage
50 lb. Bag50 lb. Bag
250050007000
800
StructuralConcretePSI (MPa)
StandardPackage
50 lb. Bag
Description
FIVE STAR STRUCTURAL CONCRETEAND STRUCTURAL CONCRETE VfO
Structural ConcreteStructural Concrete Via
Five Star Structural Concrete is a high strength, one component, concrete repairmaterial for horizontal repairs from W' to 12" depths.
Five Star Structural Concrete via is a high strength, one component, concreterepair material for vertical and overhead structural repairs.
Typical Compressive Strengths at 73°F, ASTM C 109*
3 Hours1 Day7 Days28 Days
Part No.
• modified
Part No.
FSP30050
FSP41 050FSP40050
56 Bags
SkidQuantity
35 Bags
SkidQuantity
2,500 psi (17.2 MPa)5,500 psi (37.9 MPa)7,000 psi (48.3 MPa)
NEAT
StandardPackage
50 lb. Bag
StandardPackage
1001b.Bag
FIVE STARHIGHWAY PATCH
Part No.
1 Hour after final set1 Day7 Days
AGE
FSP10100
Bond Strength, ASTM C 882:
1 Day7 Days
Part No.
FSP20050
True non-shrink metallic cement based construction grade grout. Long workingtime. High compressive strength. Easy to use. Approval CRD-621, NYS DOT 701.04.
Formulated for permanent precision support of base plates and other bearingsurfaces. Easy to use.Five Star Epoxy Grout is a three component system consisting of one can ofhardener, one pail of resin and two polyethylene lined bags of aggregate. Whenmixed together this kit produces one cubic foot (28 litres) of hardened grout.
Typical Compressive Strengths at 73°F. ASTM C 579 Method B*
PSI (MPa)
xxx8,000 (55.2)
11,000 (75.9)15,000 (103.4)
FIVE STAREPOXY GROUT
2 Hours12 Hours1 Day7 Days
0.00%0.00%0.00%0.00%
MaximumWater
+0.01%+0.01%+0.01%+0.01%
MinimumWater
FIVE STARNBEC GROUT
1 Day3 Days14 Days28 Days
Typical NonshrinkCharacteristics(CRD C-621 *)
• modified
Part No.StandardPackage
SkidQuantity Part No.
StandardPacking
FSP50050 50 lb. Bag 56 Bags FSP60050 3 Part Kit
. ,
880 MEEKER AVE • BROOKLYN, NY 1122296 Tel: 718..387..0300 • FAX: 718..387..1874
lB§!iJ =:'B~:~~=a~~~mpoundjoin' seale'~ which combines a tenacious adhesive power with high~~ resiliency. Provides a positive seal during expansion and
contraction of the joint and will not lose bond in cold weather or flow in hot weather.
USE#164 is ideal for large scale sealing of tranverse and longitudinal joints inPortland Cement concrete and joints in bridges, airport runways, taxi-strips, etc.Also used for maintenance sealing of cracks in asphaltic concrete pavement,parking lots, etc.
SPECIFICATIONSASTM 0 1190 AASHTO M 173Federal Specification SS-S-164FAA P 605State Department of Transportation Specifications
COVERAGE9.5 Ibs. per gallon71.0 Ibs. per cu. ft.Joint W' x W' in depth requires apprOXimately12.2 Ibs. per 100 linear feet.
Part No.StandardPackage
SkidQuantity
~siIi POLY-JET 1614A POLYMETRIC JOINTEAI!!m!!@ SEALANT
~~SEALTIGHT POLY-JET 1614A is a single component, hot-applied sealant used forsealing cracks and joints in Portland Concrete pavements that may be subjected tothe spillage of jet fuel, gasoline, motor oil and antifreeze. POLY-JET 1614A is notcompatible for use in asphalt concrete pavements.
USEPOLY-JET 1614A is ideal for sealing joints in highways, bridges and airport runways,taXiways, refueling and maintenance areas where excellent durability and resistance to jet fuel, gasoline and oil is desirable.
SPECIFICATIONSA8TM 0-1854A8TM 0-3581AASHTO M-282Federal Specification S8-8-1614 (A)Federal Specification 8S-S-167 (8)NOTE: POLY-JET 1614A does not meet the resiliencerequirements of ASTM 0-3406.
COVERAGEFor a W' x 1/2" joint, 131bs. per 100 ft.
WRM16455 55 lb. Carton 36 Cartons
Part No.StandardPackage
SkidQuantity
~sfIi SEALTIGHT MEL-GARD "PROTECTED"~ WATERPROOFING MEMBRANE
~~8EALTIGHT MEL-GARD combines the desirable advantages, features and qualitiesof both roll and panel-type membranes into a versatile, flexible, tough, durable andeasy-to-handle membrane for general waterproofing applications. MEL-GARD"Protected" Membrane provides (1) a waterproofing membrane (2) a vapor barrier,and (3) its own protection course...all in one application that saves up to 30% inapplication time and money. MEL-GARD eliminates the requirement for a separateprotection course or drainage board.
lB§!iJiIi· GARDUX HORIZONTAL JOINT SEALANTEAI 16Hl
® GARDOX is a pourable, two-component, cold-applied com~ pound for sealing joints in concrete. Chemically reactive~~ polymers plasticized with coal tar cure to a durable, rubber-
like joint seal that offers a firm, smooth, non-tracking sureface retaining flexibility from -20°F to over + 200°F. Effectively seals the joint againstwater infiltration and rejects incompressibles.
USEGARDOX is recommended for sealing horizontal joints on highways, airportrunways, bridges, plaza decks and driveways. Interior uses include the sealingof joints in industrial floors, garage floors, airplane hangar floor joints, etc.GARDOX is resistant to incidental spillage of jet fuel, oil and gasoline.
SPECIFICATIONSAMTM C 920, Type M, Grade P, Class 25, Use TFederal Specifications S8-S-200E, Type HFederal Specification SS-S-195, Type HFAA Item P-605CRD-C 526, Type H
COVERGEA joint W' wide by Y2" deep requires approximately 1.4 gallons per 100 linear feet.
WRM61450
Part No.
WRM10010
50 lb. Pail 36 Pails
StandardPackage
50'x4' Roll
lE§TiIiGSNAP-CApTM EXPANSION JOINT CAP
EAI!!.§!:!!i' SNAP-CAP Vinyl Expansion Joint Cap provides a time and
~ cost-saving method offorming straight, uniform and debris~~ free reservoirs for joint sealing. Exposed concrete surfaces
assure adherence of the sealant to the joint interface.
Part No.
WRM50001
Part No.
StandardPackage
1 gal.
Size
CartonQuantity
4 gal. Carton
StandardPackage
1E5Ts iii SEALnGHT MEL-ROL WATERPROOFINGEA~ MEMBRANE
~~~A premium grade, versatile, dependable, sheet type waterproofing membranecomposed of a nominally 56 mil. thick layer of polymeric waterproofing membraneon a heavy duty, shrink resistant 4 mil. thick, cross laminated polyethylene film. Thetwo components are laminated together under strict quality control productionprocedures to provide dual protection.
WRM91205WRM91210WRM91215WRM91220
3!a" x 10ft.W'x10ft.314" x 10ft.1" x 10ft.
Box of 1000'Box of 1000'Box of 700'Box of 500'
Part No.
WRM10015
StandardPackage
60' X38.5" Roll
. 1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631..242..8555 • FAX: 631..667..8869 97
~SEAITIGHT PREMOULDED MEMBRANE VAPOR SEAL
® WITH PLASMATIC CORE---..!'!!!!!!"'-~~ A permanantfy bonded, multi-ply, semi-flexible core
board consisting of a plasmatic matrix encased intwo layers of pure-blown, high melt-point asphalt. The three-ply core issandwiched between liners of asphalt saturated felt and a glass-matliner.An asphalt weathercoat is applied to the glass-mat liner and covered witha polyethylene anti-stick sheet.
~SEA.ITIGH PROTECTION COURSE FOR MEMBRANE
T® WATERPROOfiNG--~:-"-PI'IODU~
CCNC~~~ SEALTIGHT PC-2 Standard Duty and PC-3 HeavyDuty Protection Course is a semi-rigid board pro
duct composed of mineral fortified asphaltic core between a layer ofasphalt saturated liner and a glass mat liner which is weather coated andhas a polyethylene film facing. With the duo-facing, SEALTIGHT Protection Course offers compatibility with most currently popular vapor andwaterproofing materials. Consult the waterproofing manufacturer to determine which side is approved "as compatible" to a specific waterproofing prior to application.
~ ASPHAlT EMULSIONS
1#) SEALMASTIC emulsion-type dampproofings are~~ the breather type which permit moisture vapor to
escape through the film while remaining resistant towater penetration...prevents blistering of applied films.
TYPE I - SPRAY GRADE...an asphalt base, non-fibred, clay emulsiontreated to provide greater resistance to water. Resists flow or sag. Twocoat application recommended on masonry block walls above-grade, forstone backing and for below-grade dampproofings.
TYPE 2 - BRUSH-ON OR SPRAY GRADE...an asphalt base, clay emulsion with fibres. Formulated to offer a tight film that combines excellentstrength and resistance·to water. Use to protect exterior, below-grademasonry walls against moisture penetration.
TYPE 3- TROWEL GRADE...a mineral colloid, asphalt emulsion fibratedwith selected fibres. Ideal for light trowel application to below-grademasonry walls and to protect porous or irregular surfaces. Offers highresistance to weather, water, corrosion and abrasion.
~EAifI6HT SEALMASTER DAMPPROOFINGS
l!!!!!!!®
~SEALMASTIC Solvent Type Dampproofings contain
I'>l'ICIDUC"TS .
CONCA~R~ an exclusive wetting agent to connect a naturallyhydrophilic surface to a hydrophobic surface to assure
proper adhesion. They provide a flexible coating that will not crack undernormal expansion-contraction.
SPRAY-MASTIC®...a non-fibred asphalt compound for use where sprayapplication is desired. Two coat application is recommended on masonry block walls above-grade, for stone backing and for below-gradedampproofing.
SEMI-MASTIC®... a brush or spray-on fibred asphalt compound for theprotection of exterior masonry walls and below-grade walls. Spans smallholes and hairline cracks... withstands temperature changes withoutcracking.
TROWEL-MASTIC®...a trowel-applied, heavy-bodied, fibred asphaltcompound for application to exterior surfaces or masonry walls belowgrade. Ideal for porous and irregular surfaces. Spans small holes andhairline cracks and withstands temperature changes without cracking.
~SEAlili I'! HI SPEC®. POLYMERIC SEALANT - HOTlu HT® APPUED
--~~PRCIDU~
CCINC~~ SEALTIGHT HI-SPEC is a premium-quality, hot-ap-plied joint sealing compound. It is formulated with
100% virgin polymer, asphalt, plasticizers and reinforcing fillers to produce a joint sealer that has excellent bond properties, will not becomebrittle at low temperatures and will not flow or migrate from the joint attemperatures of 140°F.
USEHI-SPEC is recommended for large-scale sealing of joints and cracksin concrete and asphaltic concrete pavements. Typical applicationsare the sealing of expansion and contraction joints in concrete highways - both transverse and longitudinal, sealing joints betweenconcrete pavements and asphaltic shoulders and sealing randomcracks in both concrete and asphalt pavements.
SPECIFICATIONSASTM D3405AASHTO M 301Federal Specification SS-S-1401CCRD-C 530
Part No.
WRM10020
Part No.
WRM10030
WRM10035
Part No.
WRM10060WRM10065WRM10070
Description
PC-2 Std. Dty. ProtectionCoursePC-3 Hvy. Dty. ProtectionCourse
Description
Spray-MasticSemi-MasticTrowel-Mastic
Sheet Size
4' X 8' Panel
Size
Va" x 4' x 8'
V4" X 4' x 8'
StandardPackage
5 gal. Pail5 gal. Pail5 gal. Pail
Part No.
WRM10075WRM10080WRM10085
Part No.
WRM10055
Description
Asphalt Emulsion SprayAsphalt Emulsion BrushAsphalt Emulsion Trowel
StandardPackage
55 lb. Carton
StandardPackage
5 gal. Pail5 gal. Pail5 gal. Pail
SkidQuantity
36 Cartons
. 880 MEEKER AVE • BROOKLYN, NY 1122298 Tel: 718-387-0300 • FAX: 718-387-1874
EVAlOTE .. Expansion Joint MaterialEvazote is a resilient, UV stable, preformed, flexible expansion jointmaterial. It is a low density, closed cell, cross linked ethylene vinyl acetatepolyethylene copolymer. Evazote's cell generation is achieved by beingphysically, rather than chemically, blown using nitrogen. This uniqueprocess prevents Evazote from retaining the chemical residues thatcontaminate other EVA foams. This also ensures a high level of qualitycontrol. Moreover, no halocarbon gases (e.g., CFC's, HCFC's, HFC's) orvolatile hydrocarbons are used at any time during Evazote's production.This allows for the manufacture of a pure and chemically inert material.Therefore, it has superior chemically resistance as well as being safe foruse with potable water and other environmentally sensitive applications.Futhermore, grooves are placed along the sides of the material. Thisenhances its bond strength to the surface. .
SERVA BOND #1 .. Epoxy BonderServa-Bond 81 is a 100% solid, two component, modified epoxy adhesive designed for bonding construction materials including Evazoteand Plastazote. It is workable to 40°F. For colder applications, use ServaBond Cold Cure #41. Serva Bond. 1meets ASTM C 881. Type 1, Grade3, Class B & C.
Packaging: 4 U.S. gallon units/case.
PROCRETE NH .. Elastomeric ConcretePro-Crete NH is an elastomeric concrete designed for use in high stressand impact areas such as expansion joint end dams on highway bridgesand parking structures. It can be used anywhere that a waterproof.flexible, and energy absorbing transition area is required.
Packaging: .37 cubic foot kits, or 3.7 cubic foot kits.
USES• Expansion joints• Pressure relief joints• Isolation joints• Hydrostatic conditions• Sound barrier joints• Gaskets (pipe through wall seals)• Irregular and varying size joints
Use with Serva Bond #1 Epoxy Bonder.
Typical Coverage at 70°F. for general surface conditions.
Evazote &Plastazote Serva Bond AdhesiveDepth (in.) linear feet/galion
1 100 - 1202 ~-®
3 ~-~
4 ~-~
Features• Fast-setting without vulcanizing• Abrasion resistant• Impact resistant• Waterproof• Outstanding bond strength• Traffic resumed in 2 hours• Crack resistant• Non-shrink
SEEKURE REINFORCED KRAFT PAPERSeekure is used for positive protection of finished floors and carpetingduring final construction stages. It is also used to protect wainscots fromdamage and stains during subsequent construction. Can be used toprotect resiliantflooring, tile, carpeting. marble, granite, terrazo, wood orconcrete floors and other finished surfaces.
It consists of two layers of kraft laminated with a blending, non-stainingadhesive and is heavily reinforced with glass fibers to resist puncturesand tears.
Finished Floor Protection
Part No.
FOF38936FOF38948
Roll Size
36" X 300'48" X 300'
Area Per Roll
900 S.F.1200 S.F.
1 SOUTH SECOND ST. • DEER PARK, NY 11729 .Tel: 631..242-8'555 • FAX: 631-667-8869 99
8111 SILICONE ADHESIVE/SEAUUff ONETIME GLAZING COMPOUND CONCRETE AND MORTAR REPAIR
ARCHITECTURAL-GRADE BUTYL RUBBERSEALANT
))
Cartridge CaseSize Qty.
10.3fl. oz. 12Concrete/MortarRepair
Description
Cartridge CasePart No. Color Size Qty.
RED8460 White 10.3fl. oz. 12RED8465 Gray 10.3fl. oz. 12RED8466 Black 10.311. oz. 12RED8467 Clear 10.3fl. oz. 12
RED646
Part No.
This is a premium formula for fast, durable repairs. for patching cracks in driveways, sidewalks, or repairing mortar between bricks,stone, cinder blocks and on steps. Easy application; water clean-up; retains flexibility whencured and is paintable - won't stain or bleed.Gray textured to blend with mortar.
General purpose formula applies easily, driesqUickly and is paintable. Won't stain or bleed.
Contruction grade 35 year siliconized acryliccaulking for use on doors and windows. Thispremium formula is easy to apply and is paintable, odorless and mildew resistant. Easyclean-up with water.
CONSTRUCTION GRADE 35 YEARACRYLIC SEALANT
(:(i L}ifllff6(p
LATEX CAULK
~)I.U~Cartridge CaseSize Qty.
10.311. oz. 12White
Color
Cartridge CasePart No. Description Size Qty.
RED666 Glazing 10.311. oz. 12Compound
New CELULON adhesive sealant for plumbingand HVAC contractors answers a real need. Notonly does CELULON exhibit adhesive characteristics superior to silicone in most peel andshear tests, but it is also paintable, cleans upwith water and has no offensive odor.CELULON is especially recommended for sinkand countertop installation, sealing arounddrains, showers and tubs, replacing brokentiles and fixtures, sealing interior/exterior airconditioning lines, pipes, and sealing unlikesubstrates such as: brass, stainless steel, castiron (primed), Formica (back), porcelain, concrete, cinder block, PVC and fiberglass. CELULON is also effective on glass, aluminum andmany other surfaces.
RED936
NEW CELUlON™ PLUMBING I HVACADHESIVE SEALANT
Part No.
The siliconized acrylic formula creates a durable, watertight bond to most interior/exteriorsurfaces. Cartridge with easy applicator tip provides excellent gunnability. Water clean-up.Stays flexible for years. Meets ASTM Spec. C669.
12
CaseQty.
10.3fl.oz.
CartridgeSizeColor
White
Cart. CasePart No. Size Color my.
GE1200CC 11oz. Clear 12GE1200WC 11oz. White 12GE1200BC 11oz. Black 12
Part No.
RED697
A one component RTV (Room TemperatureVulcanizing) industrial strength silicone sealant. This high performance architectural glazing and sealing compound will hold under themost demanding temperature extremes. Use itwherever a tough, permanent elastic seal isrequired. Adheres to aluminum, plastic, metal,glass, ceramic tile and most non-porous surfaces. It is waterproof and weatherproof. Canbe used indoors or out. In addition to listedcolors, it is also available in bronze and gray.
Meets Federal Specs TI-S-00230 andTI-S-001543 and Mil Spec MIL-A-46106AASTMC-920-79.
This professional, architectural-grade sealantis specifically formulated for tough, tight, waterproof seals on most construction surfaces. Theright choice for below-grade applications; marine usage above water line. Paintable. Solventclean-up.
PANEL AND CONSTRUCTION ADHESIVE Part No.Cartridge
Description SizeCaseQty.
This solvent based adhesive permits panel installation on wood, brick, wallboard or metal.Great for marine repair above the waterline,installing acoustical tile and underlaying flooring. Outstanding initial tack allows for immediate installation. Solvent clean-up.
12
Description
Glazier's Chisel
Latex Caulking 10.311. oz.RED736
Part No.
This is a heavy duty steel chisel with woodenhandle. Removes hardened putty quickly. Prepares sash for glazing. Overall length 11314".
BladeWidth
RED1941
GLAZIER'S CHISELS
10.31I.oz. 12
Cartridge CaseSize Qty.
Panel!ConstructionAdhesive
DescriptionPart No.
RED676
BLACIITOP AND ROOF REPAIR
U~~I@:PThis Butyl rubber/asphalt formula outlasts conventional compounds. Fills cracks in driveways, repairs flashing around chimneys andskylights and fills expansion joints in concrete.Excellent water resistance. Solvent clean-up.
Cartridge CasePart No. Description Size Qty.
RED636 Blacktop/ 10.3 fl.oz. 12Roof Repair
, ~ ~ -
880 MEEKER AVE • BROOKLYN, NY 11222100 Tel: 718-387-0300 • FAX: 718-387-1874
ROYSTON ROYAL..GARDTM ARCHITECTURAL MEMBRANEROYAL-GARDTM MEMBRANE SYSTEMSDesigned for installation on horizontal and
vertical, below-grade surfaces. "High-tack"compound provides instant adhesion to dry,primed walls yet, it is "contractor-friendly"allowing repositioning during installation. Fulladhesion in one hour. Self-sealinglongitudinal seams achieved with compoundto-compound contact at overlaps. Criticalareas can be heat sealed for addedprotection.
1. Release Film2. Rubberized Asphalt Compound3. Nonwoven Fiber Glass
Reinforcement4. Rubberized Asphalt Compound5. Polyester Film
ROYSTON ROSPHALTTM 50 ASPHALT PAVING MIX
Application
General PurposeWaterproofing(foundationwalls, tunnels)
InstallationTemperature
For low tempapplications(25°F-44°F)
WaterproofingSystem
Royal-Gard™ &Roybond™ 713APrimer
Royal-Gard'" &Roybond™ 740Primer
• Bridge Decks• Roadways• Parking Garages• Driveways• Ramps
RosphalFM 50 has a 15-year proven performance record representing major innovation inasphalt paving design technology. Conventional asphalt paving mixes are modified for"zero-void" content creating waterproof pavement with lower cold temperature fracture toapproximately -35°F while raising high temperature deformation to approximately 250°F. Themodified wearing course mixes are tough,dense, and waterproof.
Waterproofing properties prevent penetration of deicing salts.
Installation flexibility eliminates costly sur-face preparation on irregular deck surfaces.
Shortens down time and can be applied under traffic.
Withstands heavy traffic as a thin, highperformance wearing course.
ROSPHALTTM 50 IMPROVES AC-20 ASPHALTPERFORMANCE
AC-20 AC·20WITHProperty ALONE ROSPHALT''' 50
Low TemperatureEmbritllement 20°F -35°F**
Softening Point-Ring & Ball 123.8°F 250°F**
ItTypical results may vary with AC-20 source. Not intended as a specification"'"*Approximate:ly
RosphaWM 50 paving mix is applied using conventional paving equipment and operatingprocedures.
© 1992 Royston Laboratories Division, ChaseCorporation
CHASECl~~:Rovstoncorporation ..,4....,,
••• •.. ...ROYSTON LABORATORIES DIVISION
The technical data furnished is true and accurate to thebest of our knowledge. However, no guarantees of accuracy are given or implied. We guarantee our products toconform to Royston Quality Control standards. We assume no responsibility for installation, coverage, perlormance, or injuries resulting from use. Liability, if any, islimited to replacement of products determined to be defective by Royston's Quality Control standards, exclusive oflabor for installation and!or subsequent damage resulting!causing functional damage either directly or indirectly.Prompt reporting (within four (4) working days) of suspected defective product is required. Prices and cost data aresubject to change without prior notice.
1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631..242-8555 • FAX: 631..667-8869 101
ROYSTON FIBER GLASS-REINFORCED WATERPROOFING SHEET MEMBRANES• Foundations• Roadways• Plaza Decks• Bridge Decks
Internal strength provided bywoven or nonwoven fiber glassembedded in rubberized asphaltenhances surface toughness, overallmoisture resistance, and low-temperature flexibility. Resilientpliability permits handling withouttearing during installation andprotects against cracks that developover time.
Reposition during installation without tears, waste, trapped bubble&--Controlled tack adherence reaches full adhesionin one hour.
Fillets are not needed because of the excellent curbline fit.
Manufacturer's warranty_ Copies available upon request.
Royston's exclusive "Leading Edge" creates a compound-to-compound, monolithic, "self-seal" that is as strong and waterproof as the continuous sheet.
Royston Sheet Membrane ProductsMembrane Self-SealingProduct Size Mil lap Joint Application
10A 48" X 50' 60 Yes Woven glass reinforced bridge membrane
10AR 48" x 50' 70 Yes Woven glass reinforced bridge membrane with woven polypropylene top sheet
104AHT 48" x 50' 60 Yes High-tack, woven glass, architectural membrane
104ARHT 48" x 50' 10 Yes High-tack, woven glass reinforced architectural membrane with woven polypropylene topsheet
108AGN 48" x 50' 50 No Nonwoven, economical glass membrane
108ARN 48" x 50' 70 No Reflective cracking membrane with woven polypropylene top sheet
108ARN 24" x 50' 70 No Reflective cracking membrane with woven polypropylene top sheet
108ARN 12" x 501 70 No Reflective cracking membrane with woven polypropylene top sheet
10AN 48" x 50' 60 Yes Nonwoven glass bridge membrane
Royal-Gard™(104AHTN) 48" x 50' 60 Yes Nonwoven glass, high-tack architectural membrane
Membrane CodeHT - High TackN -NonwovenR - Woven polypropylene top sheet10A - Standard tack104 - Nonbridge108 - Always high tack
Primers713A - Standard7138 - Low VOC744 - Surf-Prep (Water base)740 - Cold Temp (25°F-45°F)750 - Sprayable
NOTE: See our Spec-Data® Catalog Insert(Section 71 OO/WATERPROOFING) for detailedinstallation specifications.
880 MEEKER AVE • BROOKLYN, NY 11222102 Tel: 718-387-0300 • FAX: 718-387-1874
HORN/DURAJOINT® PVC WATERSTOPHorn/Durajoint® PVC Waterstop is used in portland cement concrete construction topreventthe passage of water through expansion joints or construction joints in almostevery type of structure, whenever water has to be kept out or kept in, whether above,at, or below grade.Horn/Durajoint® PVC Waterstop is available in many different types and crosssections, several of which have one split flange for use where the elimination of splitform work is desired.Ribbed with centerbulb are the most commonly used waterstops in expansionjoints where movement is expected.
Ribbed Flat waterstops are ordinarily used in joints where movement is not expected.Dumbbell waterstops are primarily used in below-grade joints where little or nomovement is anticipated.Dumbbell with centerbulb waterstops are designed to be used where movement,even if transverse and longitUdinal, must be accommodated.Baseal® waterstops are designed for ongrade installation at the bottom of concreteslabs to prevent upward seepage of ground water through joints, or in thin slabconstruction, or to waterproof joints at wall/slab junctions.
Ribbed Type with Centerbulb Dumbbell Type without CenterbulbAPPROX. HEAD OFWT. LBS. WATERLIN. FT. FT.
APPROX. HEAD OFWT. LBS. WATERLIN. FT. FT.
Type 2For construction joints. 0.39 65 3/16')
Type D8-1For construction joints. 0.83 65
Post Applied Ourajoint
-L.3/1__--tIT
TYPE 26
tJiO .+-
t-,I__, ,--_.IT
fl!I t....1--,
!3/8 .1-'•••__••• 3/Q
.....1, ~t_ 6 _---tot~T
! 'I,' ..L.IIIIIJ!I---•• ',"t T,,",1.---6"---
t 1-..•---... ',,"
It 3/16" T
1-_ 6" __
65
90
100
100
100
100
~" 1}l£sYi+.rnr\}~3-1/4'~ 1..---4.7/16--1
TYPE 25
2.34
0.50
2.21
0.76
0.98
1.53
Special Shapes
Type 08-4For expansion joints 1" or lessin width.
5118" - •
~..l.~1/2
I , 11
c 8.----+C" 3/16"' 1. 7110'I 1111111
150
100
150
2.24
0.83
1.14
Type 15Construction joints in 1 29 125 11." j 318' I lro" Type 08-5foundation walls and footings. • lit II I 1111 For composition joints below
1-- -1-__-1- 1--__1===_'-_[;'_'-_1-_--=--=-_1------j grade where little or noMONTGOMERY ENGRG. movement is expected.
Type 12 Type 08-2Construction joints in 1.07 100 ,"_J"~.' _~I *,,,,.. For expansion joints W' or less
I-f_ou_n_da_ti_on_w_a_lIs_a_nd_f_oo_ti--.:ng=--s_.+---+------+--------------1 in width.
Type 13 ~/8 -*-Construction joints in 100foundation walls and footings 1.59 f.o---26 ----1-1 Type 08-3where greater hydrostatic For expansion joints 1" or less
f--:p_re_s_su_re_is_a_n_tic....:.ip_at_ed_.--i----I-------l---------------j in width.Type 14For deep embedment inconstruction and expansionjoints where shear movementis not anticipated.
Type 11Construction joints in 1.46 100 'I," W
foundation walls and footings 1111111 t It' IllllllTil Type 08-7where greater hydrostaticpressure is anticipated. %" I Same as Type 08-5 but will
1----------1----I----I-------------j take higher head of water.Type 11A MONTGOMERY ENGRG.For deep embedment in I---- g_
construction & expansion joints 2.14 150 I . '!o- -lIt·where shear movement is not III 111(" 1111 '2, Type OB-8anticipated. Economical shape for
1------:.-------1----1----1----------- construction joints belowType 11B MONTGOMERY ENGRG. grade.Ourajoint flat ribbed waterstopsare used in construction jointswhere little or no movement isexpected. Found generally inbelow grade footings, walls, Used in difficult forming areasand slabs. that do not require ahigh head
f-T-y-pe-1-1-C------+---l----+--M-O-N-T-GO-M-E-R-Y-E-NG-R-G-.-----1 of water.
C -II' J7Il"~. 3/18·
- IIlJl:I\&:~
Type 18Post Applied Ourajoint wasdesigned to attach newconcrete structure to existingconcrete. Providing watertightjoint with limited movements.
2.80 NA
- ,
1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631-242-8555 • FAX: 631-667-8869 103
HORN/DURAJOINT® PVC WATERSTOPHorn-Durajoint® PVC Waterstop is extruded from an elastomeric plastic compound consisting of Horn/Durajoint® PVC Waterstop is chemically inert, contains no material leachable by water, andvirgin polyvinyl chloride and additional resins, plasticizers and stabilizers to meet or exceed the is highly resistant to acids and alkalis, to ozone and oxygen, and to waterborne chemicals. It isrequirements and performance criteria of Corps of Engineers Specification CRD-C 572-74. An fungus resistant, as tested against the specifications outlined in Mil. Std. 81 OB, Method 508. It willarctic grade is available on request to meet Ontario Hydro Std. M-264-81. No reclaimed or notfatigue on repeated flexure, and it retains its strength and elasticity through atemperature rangereprocessed materials are used. The finished material is gray in color. from as low as -35°F to ahigh +175°F.
NOTE: Head pressure ratings are for reference only, Actual ability to resist head pressure depends on the quality of concrete and placement,
Ribbed Type with Centerbulb Type 8 ONTARIO·HYDRO
For exceptionally high heads of 2.70 150+ I ... ,-----jAPPROX. HEAD OF water and application in major ..l._'-WT. LOS. WATER structures, dams, power .- II'LIN. FT. FT. l/' 'I' , fhouses, etc. 1/~· 0.0.
Type 3 0.50 CH2M-HILL Type 78K BUREAU OF RECLAMATIONType 3A 650.40 Use when extra movement in 2.65 150+
\ 1111 ,I! !,::Ot 111111~~Construction joints. 1111 lit eat 111111 both shear and expansion is
3/16 'I," ·0,0, expected.
3~ O,O.l'k'
r-- 4 ----j Ribbed Type with CenterbulbType 4- APPROX. HEAD OF
WT. LBS. WATERConstruction joints. For higher 0.89 100 I, 6 ., LIN. FT. FT.heads of water or larger
illlllltO~1I illmovement than Type 3. Type 93/16 'I," 0,0, Extra heavy duty for higher 1.64 150 I; 111111r.9 111111;6heads of water & will resistType 48
0.70 100 I" 6 -.----1 displacement during pour. %/fSimilar to Type 4, however 1.0 %'
tapered for economical but
"'1 ·0 - 00 '!o" -
effective water stoppage.t3/1~'I'''O.0
MONTGOMERY ENG CH2M·HILL1/8
Type 4CType 10Will accommodate extra 2.34 150
1111111111 ;- p 11111111 11Expansion and construction 1.04 100 ,. 6 I movement in both expansionjoints where lateral movement
~and shear. 00 \' ID 'k' CH2M.HILL '10'
is anticipated. MONTGOMERY ENG CH2M-HILL1'/," 0.0.
Type 5BR BUREAU OF RECLAMATION
Type 5 Extra heavy duty. Will also 1.26 125 3116"[ liB'.' [ <' 11116"00Heavier duty than Type 4. Will 1.26 125 I" & ./
resist displacement during'''Ilt! 0 II Itt It
resist displacement during
It~D.pour.
I 3ls"t "3/B''I0. Iconcrete pour. 6"----+
Type 31Type 5A ONTARIO·HYDRO I 12" IFor extra high dams. 3.18 250+ I I I 1111~o!",11 I I I~'Similar to Type 5. 1.65 125 1--"--1Recommended for small dams =::- I a II 1~4'and hydro projects. Type 7DI~:IZ" J/O" \00"'" r I 9' IFor larger heads of water 2.1 150+ 1111111111~"D9!~.~~~11111 ';'11\1dams, reservoirs, sewageType 6For large expansion joints in 1.07 150 I , I plants, or locks with larger
movement.retaining walls or roof slabs. l/l6to, 1 '18
1 Type M3l/l~ D.O.
1.5 150 r-:- ~:. ~- 'r,' IEconomical shape for use inType 7 expansion joints of 1" or less. wllllill ~L;Ii [,~,.!,lo~~11 H"
For iarge heads of water-dams, 1 1 9 I1.62 150+)/,1 c,major reservoirs, sewage T 3/16" Dumbbell Type-Split without Centerbulbplants or locks. ". 0.0
Type 7C Type 08-2001.54 100 ~3/8 ~IWill accommodate extra 2.24 150+ I , I For expansion joints Vi' or less
movement in both expansion t I IlIIt~/'1II11111 in width.
I· I c 3;4'and shear. t'l' 3/8 t'W.O.D.
~6 .ITType 7f
Type D8-300For large transverse and shear 3.01 150+ I ' i 2.21 100 r/. --.L.movements in major *IIl1l1i!/I,lt(E) 1111111111For expansion joints 1" or iess
~in width.Sl/4'
structures. t 41TII" _.....1O",...z',,"o.o. _ .880 MEEKER AVE • BROOKLYN, NY 11222
104 Tel: 718-~87-0300 • FAX: 718-387-1874
Factory Made Splices available upon request
~~
flat tee ~flat ell ~~~ross ~flat cross
Special Shapes PVC Masonry Control Joint UnitsAPPROX, HEAD OFWT. LIBS, WATERLIN, FT. FT.
Type 16 PVC Masonry Control Joint units are designed to be used with standardBridge deck joints to meet Cal.
1.1 NA ~Iconcrete blocks to provide a vertical joint of stress relief in concrete
State. Hwy. Dept. specif. r-· ·2\4" __ - -'/." 2'A.," masonry walls, while providing adequate shear strength for lateral.j:~"..,t'" !~ stability.
Type M1 Control joints should be used about every 20 to 35 feet in average walls,Used as construction joint in
.058 NAlI>·l~ ..~y..! 1~1111
but should not be spaced more than twice the wall height for high walls.thin walls and slabs.
.'\10.. 'It••
Control joint units are extruded from a specially formulated PVCType M2 Compound in 4 LF lengths.Bridge and highway
1.7 NA ~..} Iconstruction joints between .i" ·~~"'13
Type 20 and Type 21 are used both in block walls and brick veneer.deck and curbing or parapet ~'I· They are used with less expensive joint fillers and are ideal betweenabutments. --,- "t.y." columns and walls.
Type 17 Type 20 Type 21For greater embedment in
1.25 50 f 3116" -A. I 518,,:1 I- 1<-1318"construction joints or thin walls 1111111111111 , 1" 'Ill"
and slabs. II 9" I
1.9I1J"1-:= 5116"+:1'~-f.Type 27 lY2" ,'I"
For construction joints on0.78 NA 118'
highways and bridges.~ Type 22 and Type 24 are used in 8-inch and 6-inch block walls. This
configuration provides protection from foreign materials.1---6'---1 Type 22
Type 28,4-718" >1For construction joints on
1.00 NA 1/8'
W>rhighways and bridges. III I': I l(l..... I! III IIIII1 ) (-r-
TEAR WEB ! 19116"I· g' _I
Type 29 r"'::=:=LUsed to attach new concrete
I~';'elt
structure to existing concrete. 0.82 NA ) 1 'TProviding watertight 3'
construction joint with little or L 1/8' Type 24no movements,
Ia 3' .1 Type 23 is used in block walls and brick veneer with the ability toprovide protection against the penetration of foreign materials.
Baseal® Type Joint Seals Type 23
Type 66 NEW YORK TYPE D 518" ~Base seal for wall and slab
0.83 ,I, .11111111'construction joints.
JI8" 'I' • 11.5/1"
Type 60 IE l607/S'' ~For construction joints in slabs
0.80 1/8-.L I 'I I I-Jw Typical Physical Propertiesand walls.T~ '.I/'·-----i y-
Tensile Strength ASTM 0-638 2000 psiType 61 Elongation ASTM 0-638 360%Heavy duty for construction
1.51 '/l'-.L J J J-L
joints in slabs and walls. J,,,,. Specific Gravity ASTM 0-792 1.38TI -IT,
Hardness Shore A ASTM D-2240 80 ± 5Type 62Heavy duty for expansion 1.64 ".....1..1 I n I
-...Ljoints. J"'"T 1 jT.-
1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631..242-8555 • FAX: 631..667-8869 105
Dumbbell Type with CenterbulbType 08..9
2.10 100 318" jFor expansion joints 1" or less 1 3WD,D, 3IB"If)
in width.; 0 i liZ"
-Ir
I~~..
Type DB-100.0.1·111"
~1.u4. LFor horizontal and vertical 1.25 125expansion joints where !11l"
reinforcing steel does not allow ,-t e w'
use of 9" waterstop. I 'I'__IT
Type DB.,611/i f' 0 3
/4"0 .+For expansion joints up to 1W' 2.92 150in width. Will accommodate
both transverse & longitudinal1..--- 9' ___I t
movements.
Type D8-11To be used in large pours with 3.65 150
1----9"~
expected movements, ~Lfloodwalls, large treatment 1"
plants. 1~0.0.2_'I4"T
WATERSTOP IRONS
Split Ribbed Type with CenterbulbType 300
0.50 65 '---4 ----iSame as Type 3 but has one
~split flange.
Type 4000.89 100 I 6 ISame as Type 4 but has one
Of J/ '6split flange.
Type 400C1.04 100 I-- 6 I ISame as Type 4C but has one
split flange. ~Type 500
1.26 125 t--- 6 ---------jSame as Type 5 but has onesplit flange. ~~"4
l/8
Type 7001.62 150+ a, i.Same as Type 7 but has one
split flange. f+----9·_3/S·_._""f16·
Type 3100 3.18 250+ I---~ 12" - I,D.;/2"-----{For extra high dams. ::::: :~L!, III f~,,314"
Electrical splicing for fast, easy splicing of PVCwaterstop in the field. All splicing tools haveteflon cover with 6' power cord. UL listed.
Part No.
TAM99001TAM99002
Size(in.)
2 x 1441/2 X 14
Watts
600600
Wt.(Ibs.)
55
SUGGESTED FORM CONSTRUCTION DETAILSFOR WATERSTOP INSTALLATION
GROOVED CLEATS TO HOLD WATERSTOPS GROOVE IN FORMWORK
, c
. 880 MEEKER AVE • BROOKLYN, NY 11222106 Tel: 718-387-0300 • FAX: 718-387-1874
J "
VOleLAY TYPE eR PANELSfOR BELOW-GRADE WATERPROOFING
I •Benloseal troweled<over form-lies
•Type 1 Panels®
•
j ......,.--- 1-1/2" (38 mm) overlap
Waterstop-RX(min. 3" coverage)
6" (150 mm)
Volclay Panels consist of sodiumbentonite, a nontoxic mineral of volcanic origin, which swells up to 15times its dry volume upon contactwith water, sandwiched between layers of biodegradable kraftboard. After backfilling, the swelling of the sodium bentonite is confined by thepressure of the backfill and thusforms a tough, impervious, permanent waterproof membrane. TypeCR Panels can be used in salt water,fresh water or where groundwatercontamination exists. Volclay Panelscan be quickly and easily installedimmediately after forms are strippedusing Ramset/Redhead shots andwasher headed pins also availablefrom Siegel Bros.
Part No. Description Panel Size
VOL10100 Volclay Type CR Panels 4' X 4' X 0/16"
•RX 101
VOL10600 1" x %" x 16'8" RX-101 6VOL10700 3!4" x 3Ja" X 25' RX-102 6
Waterstop-RX is a flexible strip, concrete waterstop that provides a permanent seal by expanding uponcontact with water. Waterstop-RX is asodium bentonite product that is designed to replace conventional PVCwaterstop, thus eliminating the needfor split forming and product seamwelding.
Rolls/Desc. Case
RoilSize
PartNo.
-RX 102
POLY SCRIM"'.RX lOlT
VOlCLAY WATERSTOP - me
VOLeLAV WATERSTOPPAGEVolclay Waterstoppage is pure granular Volclay Bentonite. It is used todetail critical areas that may requireadditional Volclay protection.
VOletAY HYDROHAR TUBESVolclay Hydrobar Tubes are sausages containing sodium bentonitefor use in corners with either VolclayPanels or Voltex geotextile material.
Part No. Desription Ctn Qty
VOL10200 2' HydrobarTubes 16
BENTOSEALTROWEL-GRADE BENTONITE COM-POUNDBentoseal is a patented, trowelgrade sodium bentonite compoundused in detailing mastic around penetrations, corner transitions, unevenareas that may cause penetration ofVolclay Panels, filling up small honeycombs and cracks, tie back plates,etc. Bentoseal swells upon contactwith water, forming a tight pressureseal when used in a confined area.
Part No.
VOL10300
Desription Size
Volclay 50 Lb. BagWaterstoppage
Part No. Description Size
VOL10400 Bentoseal 3 Gal. PailTrowel-GradeWaterproofing Mastic
. 1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631-242-8555 • FAX: 631-667-8869 107
VOLIEXBENTONITE GEOTEXTllE WATERPROOfiNG
Reinforcedconcrete slabminimum 4"(100 mm) thick
@ IiiO ~ '$ 9
Bentoseal troweled<over form-ties
fj " Stagger end seams aminimum 12" (300 mm)
L\
Voltex<ID~-- ----- -------------- ~
4" (100 mm) overlap
~Hyd"b" Tob" ~~
DARK GRAY (WOVEN) AGAINSTTHE CONCRETEWHITE (NON-WOVEN) GEOTEXlllE SIDE FACINGTHE INSTALLER.
Waterstop-RX(min. 3" coverage)
12" (300 mm)
Voltex is a high-strength geotextile based Volclay waterproofing prod uct that can be used in both vertical and horizontalapplications including under slabs, property line waterproofing, solder pile and lagging and below-grade foundationapplications. Sodium bentonite is uniformly encapsulated between two layers of woven and nonwoven geotextiles.When concrete is poured against Voltex, a tenacious bond is created yielding an average adhesion value of 151bs. perlinear inch.
Part No.
V0L10500
Description
Voltex Geotextile Waterproofing Material
Roll Size
4'x15'xV4"
. 880 MEEKER AVE · BROOKL~~ NY 11222108 Tel: 718-387-0300 • FAX: 718-387-1874
, ,
POLYDRAIN DRAINAGE SYSTEMSAll standard PolyDrain channels are manufactured from PolyDyn®, an advanced formulation of selected quartz aggregates and inertmineral fillers bonded with a high-grade polyester resin. This composite material is suitable for use in exterior and interiorapplications and offers distinct advantages in terms of strength, durability, and cost over alternative materials.
PolyDyn polymer concrete is vastly superior to portland cement in terms of strength and wear resistance. Because polymer concretehas 3-5 times the compressive and tensile strength of portland cement, it can be cast much thinner and is, subsequently, muchlighter in weight. This one important factor eliminates the need of heavy equipment and the extensive accompanying labor costs.
PolyDyn is nonporous and corrosion resistant. Absorption is less than 0.2% which makes it ideal for food processing and chemicalindustry applications often requiring frequent washdown with strong cleaning agents or the capture and containment of corrosiveand sometimes hazardous materials. The smooth, mirror-like channel finish reduces flow resistance and allows fluids to pass at anincreased velocity. It is this quality that makes PolyDrain channels self-cleaning.
Since its introduction, the PolyDrain Trench Drain System has gained ready acceptance into awide variety of applications. One of thereasons forthis is the modular concept of the PolyDrain System. PolyDrain's modular design permits the user to create any drainageconfiguration using only the simplest of hand tools. PolyDrain eliminates the expensive forming that is required in building acast-in-place trench drain.
Each PolyDrain channel is a nominal meter (39.19") in length. Standard channels have a built-in 0.6% slope and are placedsequentially in numerical order. There are 30 channels, numbered from 010 to 300, that create a continuously sloped channel run.Custom trenches can be designed with intersections or miters which can be easily fabricated on-site with commonly availablecommercial grade cutting tools. By varying outlet placements, runs of any length are possible.
TYPICALPOLYDRAIN SYSTEM
End Plate -start/finish
/End Platewith PVC
",,,-' ,_;utlet
I (lBRS ~
L--tJOUII;IS~- ."'
Call for complete specifications
POLYDRAIN ACCESSORIES POlYDRAIN GRATES
208~258 ~308e.•~~~;,"oSa 108 158
4" Horizontal Outlet End Plates.
PVC Connectors.
309
6" Horizontal Outlet End Plates.PolyWall1 uses 059A, 109A,159A, 209A, 259A, 309A.PolyWall1i uses 0596, 1096,159B, 209B, 259B, 309B.
The No. 231 Shovel head isuseful on those rare occasionswhen it becomes necessary toclean the channels.
Closed End Plates,PolyWall1 uses 106A, 206A, 306A,PolyWali1i uses 1066, 2066, 3068,(Reverses to fit both ends ofchannel.)
The No. 233 Strainer is designed tointercept leaves and trash toprevent its entering the sewersystem.
Call for complete information and specifications.
1 SOUTH SECOND" 'si'. · 'Q~ER PXliK,"NY 11729 - 'Tel: 631-242-8555 .- F~~: (i31-6()j-8869 109
," ,~ , r"" \}"
FORM TIES & ACCESSORIES FORM TIES & ACCESSORIES
WING NUTS
COIL LOOPS/INSERTS
ADJUSTABLEINSERTS
~ LIFTINGt:!fl!I HARDWARE
~'PLASTIC ~PLUGS~
FORM CLAMP
CN-29 COIL WINGNUT
PENCIL ROD
COIL TIES
ST-27 ADJUSTABLE FORM BAACE
limb' '" 3 i!\ ii
CW-4 FLAT WASHER
~SNAPTIES
S-PANEL TIE
SINGLE WALER
FOR,M,ING, SYSTEM~,:~e,
0 " ~'~q ~ -~~=,
=.:-.z:~ STEEL WEDGES
~_ CONTINUOUS COIL ROD
- CC-6 COIL TIE
~PLASTIC CONES
,~" ~)\\.: ~'II ': COIL BOLTS I:J
COIL NUTS
BRIDGE DECK
~"""""",,:",' :: .,' :, :
I ,' .':.'.' I
'~r~~QjC"~
BRIDGE DECK HANGERs
BAR SUPPORTS
~, ..~ ~SLAB BOLSTER INDIVIDUAL HIGH CHAIR
4l5"g ~ ~SLAB BOLSTER UPPERHIGH CHAIR FOR
~"METAL DECK
~1\BEAM BOLSTER
~>~CONTINUOUSHIGH CHAIR
''k:.:JtBEAM BOLSTER UPPER
CONTINUOUS HIGH
~CHAIR UPPER
l! JIINDIVIDUAL BAR CHAIR
~JOIST CHAIR PLASTIC SUPPORTS
PAVING
~; 1-SCREED CHAIRS
SCREED HOLDERS
4DB-9 CONTMGION TYPE
~, ~I!DDwe:'"" '~~"'NP TUBE METAUPI.ASTiC
DOWEL STAKES
C;S&S·Y $='. $IRD-26 PAPER TUBING
RD-27 PLASTIC TUBING
Call for Complete Specifications.
880 MEEKER AVE • BROO~YN, NY 11222110 Tel: 718-387-0300 • FAX: 718-387-1874
ROUND CONCRETE fORMING TUBES CONCRETE BLANKETSFOR COLD WEATHER CONCRETE CURING
Insulated concrete curing blankets provide proper curing temperatures for freshlypoured concrete in colder weather. Closed cell foam insulation provides the highestR values available. Standard size is 6' x 25' and is available both in W' and1" thickness.
CURE-LAP WEi CURING BLANKETS
Round forming tubes are an easy way to create perfect, cylindricalconcrete columns up to 12 feet in height. They provide a finished surfacelargely eliminating the cost of additional finish work. These forms preventthe loss of moisture in the concrete assuring proper curing. Tubes areavailable in a variety of diameters and may be cut to length easily.
Part No.
CB62512CB62510*
*NYS DOT APPROVAL 711.07
Size (ft.)
6x256x25
Thickness (in.)
V21
Grade 00 blasting sand. Perfect for use in general purpose blastingwhere nonrecyclable grit can be used.
Part Diameter Length Wall ThickNo. (in.) (ft.) (in.)
SNT12012 12 12 .225SNT14012 14 12 .250SNT16012 16 12 .300SNT18012 18 12 .300SNT20012 20 12 .375SNT24012 24 12 .375SNT30012 30 12 0400SNT36012 36 12 0400
Other diameters to 60" available on request.
BLASTING SANDMade from 10 oz. burlap on one side and 5 mils of white polyethylene film extrudedonto the burlap on the other side. The burlap provides even distribution of waterwhile the poly side retains moisture while reflecting heat. Prevents surface dryingand cracking of freshly placed concrete.
10 x 100
Size (ft.)Description
Poly-Burlap Curing BlanketsBUR10100
Part No.
BURLAPFOR WET CURING OF CONCRETE30
SkidQuantity
StandardPackage
100lb.Bag
Part No.
AS0651
Black beauty blasting medium. Metallic slag for use in nonrecyclingblasting applications.
BLACK BEAUTY BLAST MEDIUM
Part No.StandardPackage
SkidQuantity
AS0141 100 lb. Bag 30 10 oz. burlap retains water and allows for proper concrete curing during warmermonths when premature surface drying usually occurs. Conforms to all state andfederal regulations.
REINFORCED POLY SANDBAGS
Reinforced poly sandbags for general construction applications. Frequently used for weightingbarricades and other equipment around construction sights.
Calcium chloride pellets provide long lasting protection against freezing of mostliquids even in the harshest winters. Packed in 80 lb. bags.
35
SkidQty.
5 x375
Roll Size(ft.)
BagSize
80 lb.
Description
10 oz. Burlap Rolls
Description
Calcium Chloride Pellet
BUR53010
Part No.
CC10080
Part No.
CALCIUM CHLORIDE
14x 26
Size (in.)Part No.
PSB01426
" ,
1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631-242-8555 • FAX: 631-667-8869 111
HI-LOW THERMOMETERS CONCRETE CYLINDER MOLDS
Registers the high and low atmospheric temperatures during the lasttemperature cycle. Side by side mercury columns register and hold thehigh and low temperatures. Easy to read and reset with special ceramicmagnet kept in a pocket on the thermometer. Range -40°F to +120°F.Size 2W' wide x 10" high.
Part No. DescriptionPlastic cylinder molds are nonabsorbent and are supplied with closefitting caps. For curing test specimens to ASTM specifications.
HLT00415 Hi-low thermometer -40°F to 120°F Part No. Size (in.)
Used for rodding specimen concrete into cylinder molds. Tamping rodsare 5/S" diameter steel rods with bullet shaped nose.
ASPHALT THERMOMETERSCCM30600CCM40800CCM60120
TAMPING RODS.'..
3x64x86x 12
Hi visibility bimetal type thermometer has a 1" dial face and 5" spiked Part No. Descriptionstem. All stainless steel construction. Supplied in plastic carrying case -CT-R-O-5-80-0---------s/s-"-S-te-e'-r-a-m-p-in-g-R-od-------with pocket Clip. Temperature range: +50°F to 500°F.
Part No.
AST02380
Description
Asphalt thermometer +50°F -500°F
ALL PURPOSE POCKET THERMOMETER
General purpose pocket thermometer is perfect for testing temperatureof wet concrete and aggregate or for general purpose industrial use.1" face with 5" stem. Supplied with a plastic carrying case with pocket Clip.Range: -40°F to 160°F.
SLUMP CONES
Slump cones are made to ASTM specifications. Made from spun steelwith no rivets or seams on the inside and is smooth from top to bottom.Includes a rodding iron and instructions on how to make consistentlyaccurate slump tests.
Part No.
PST40160
Description
General purpose thermometer - 40°F -160°F
Part No.
CSC10100
Description
Concrete Slump Cone
880 MEEKER AVE • BROOKLYN, NY 11222112 Tel: 718-387-0300 • FAX: 718-387-1874
AEF PREASSEMBLED SILT FENCE• Effective and economical sedimentation control.. Durable - easy to install
.. Oak post and lath construction, no sagging
.. Reuseable
Physical PropertiesFabric: UV resistant polypropyleneFabric weight: (ASTM 0-3776C) 3.6 oz/sydTensile strength (Ibs.): (ASTM 0-4632) 140Elongation: (ASTM 0-4632) 20%Burst strength: (ASTM 0-3786) 300 IbsAOS: (ASTM 0-4751) 30Slurry flow rate: , (VTM-51) 0.3 g/m/fF
AEF NONWOVEN GEOTEXTILES
AEF Silt Fence I
Size: 100' x 3'Stakes: 5' oak with30" laths - 7.7 1 oncenter.Fabric is sandwichedbetween stakes andlaths and attachedwith galvanized nails.
Fabric is 36" wide witha 6" skirt for properinstallation.
AEF Silt Fence II
Size: 100' x 3'Stakes: 4' oak, 7.7' oncenter.Fabric is attached tostakes with naillwashers.
AEF Silt Fence III
Size: 100' x 3' withcord and plastic netbacking.Stakes: 5' oak, 7.7' oncenter.Fabric is attached tostakes with nail!washers.
• 100% staple polyester and polypropylene needle-punched fabricsdesigned for multi-purpose engineered use
• Provide tensile reinforcement, filtration, and separation for roads,roofs, railroads, ponds, dams, trenches, landfills, and many other civilengineering and construction uses
Custom fabric and stake sizes available for individual state D.O.T. requirements.
• Resistant to tears, soil chemicals, puncture, ultra violet light exposure,and are virtually unaffected by hydrocarbons, mildew, rot, andfreeze-thaw
Fabric style
AEF GEOTEXTILES - Specifications: minimum average roll values
480 HStt 480 680 HStt 680 880 1080 1280 1480 1680 1880 2080
4.0 4.0 6 6 8 10 12150 150 200 200 270 340 41060 85 70 85 120 130 145
120 90 180 145 210 260 33575 100 75 100 100 100 10045 50 80 75 145 145 195
215 170 250 230 380 500 70050 55 75 70 110 130 145
70-140 70-140 70-140 70-140 70-140 140-200 140-200170 150 100 145 140 100 901.7 2.3 1.9 2.0 1.9 1.25 1.2
Fabric oz/yd2
Weight grams/m2
Thickness (mils) ASTM D-1777Grab strength (Ibs.) ASTM 0-4632-86Elongation (%) ASTM 0-4632-86Puncture strength ASTM 0-4833Mullen burst strength (PSI) ASTM 0-3786-87Trapezoid tear strength (Ibs.) ASTM 0-4533-85AOS ASTM 0-4751Water flow rate (GPM/fF) ASTM 0-4491Permittivity ASTM 0-4491 (Sec-')UV resistance ASTM 0-4355-84% strength retained after 500 hours 85 85 85 85 85 85 85STD. roll length (ft.) 400 400 400 400 300 300 200STD. roll width (ft.)°o 12.5 & 15 ft. -!>
14475155360100195710180
140-200901.2
85200
16545175470100300800220
140-200801.1
85200
186101906101003501200250
140-200801.1
85200
20675210675100385
1200t*275200751.0
85200
00 Seamed rolls and special widths available. Rolls wound on 4" (1.0.) cores and wrapped with black polyethylene film,*Exceeds 1200 psi capacity of testing gauge. ttNeedled and heatset.
No warranty or guarantee expressed or implied is made regarding the performance of any product since the conditions of use are beyond our control. Nothing contained herein is to be construed as permisSion or recommendation to infringeany patent. The informafion presented herein, while not guaranteed, is to the best of our knowledge accurate and reliable, American Engineering Fabrics Inc. assumes no responsibility for the use of information presented and herebydisclaims ailliabilily in regard to such use.
1 SOUTH SECOND ST. • DEER PARK, NY 11729Tel: 631..242..8555 • FAX: 631..667..8869 113
AEF GEOTEXTILES SUGGESTED USES:
Function/Application 480HS 480 680 680HS 880 1080 1280 1480 1680 1880 2080
Asphalt overlay X X X X
Drainage X X X X X
Separation X X X X X X X X
Reinforcement X X X X X X X X X X X
Embankment stabilization X X X X X X X
Railroad trackbed stabilization X X X X X X
Protective liner for geomembranes X X X X X X X
Pipe wrapping and trench drains X X X X
Waste and oil containment liner underlining X X X X X
Bridge deck reinforcement X X X
AEF WOVEN GEOTEXTILESSPECIFICATIONS
Property Test Method Results Property Test Method Results
AEF100W AEF600WFabric structure Woven Fabric structure WovenPolymer composition Polypropylene Polymer composition PolypropyleneFabric width 12.5',15',17.5' Fabric width 12.5'Fabric length 400' Fabric length 400'Weight ASTM D-3776C 30z./yd. Weight ASTM D-3776C 6.30z./yd.Grab strength ASTM 0-4632 1801bs. Grab strength ASTM 0-4632 400 x 250 IbsTrap tear strength ASTM 0-4533 651bs Trap tear strength ASTM 0-4533 100lbsBurst strength ASTM 0-3786 350 psi Burst strength ASTM 0-3786 450 psiPuncture ASTM 0-3787 (mod) 751bs Puncture ASTM 0-3787 (mod) 1251bsElongation ASTM 0-4632 20% Elongation ASTM 0-4632 25x 15UV resistance ASTM 0-4335 70% + (500 hrs) UV resistance ASTM 0-4335 70% + (500 hrs)Permittivity ASTM 0-4491 (Sec-') 0.14 Permittivity ASTM 0-4491 (Sec-') 1.5AOS ASTM 0-4751 40 AOS ASTM 0-4751 40
AEF200W AEF650WFabric structure Woven Fabric structure WovenPolymer composition Polypropylene Polymer composition PolypropyleneFabric width 12.5',15',17.5' Fabric width 6',12'Fabric length 400' Fabric length 300'Weight ASTM 0-3776C 4.2oz./yd. Weight ASTM 0-3776C 6.30z./yd.Grab strength ASTM 0-4632 200lbs Grab strength ASTM 0-4632 41O/28s lbsTrap tear strength ASTM 0-4533 90lbs Trap tear strength ASTM 0-4533 115 x 651bsBurst strength ASTM 0-3786 400 psi Burst strength ASTM 0-3786 495 psiPuncture ASTM 0-3787 (mod) 90lbs Puncture ASTM 0-3787 (mod) 1351bsEiongation ASTM 0-4632 20% Elongation ASTM 0-4632 30%UV resistance ASTM 0-4335 70% + (500 hrs) UV resistance ASTM 0-4335 70% + (500 hrs)Permittivity ASTM 0-4491 (Sec") 0.125 Permittivity ASTM D-4491 (Sec") 0.247AOS ASTM 0-4751 40 AOS ASTM 0-4751 70-100
AEF300W No warranty or guarantee expressed or implied is made regarding the pertormance of any product since theFabric structure Woven conditions of use are beyond our control. Nothing contained herein is to be construed as permission or
Polymer composition Polypropylene recommendation to infringe any patent. The information presented herein, while not guaranteed, is to the best ofour knowledge accurate and reliable. American Engineering Fabrics, Inc., assumes no responsibility for the use of
Fabric width 12.5',15',17.5' information presented and hereby disclaims aliliabiiity in regard to such use.Fabric length 400'Weight ASTM 0-3776C 5.8oz./yd.Grab strength ASTM 0-4632 300lbsTrap tear strength ASTM 0-4533 120lbsBurst strength ASTM 0-3786 600 psiPuncture ASTM 0-3787 (mod) 150lbsElongation ASTM 0-4632 20%UV resistance ASTM 0-4335 70% + (500 hrs)Permittivity ASTM 0-4491 (Sec") 0.106AOS ASTM 0-4751 40
880 MEEKER AVE • BROOKLYN, NY 11222114 Tel: 718-387·0300 • FAX: 718-387-1874