continuum pedicure spas

Continuum® Pedicure Spas

BRAVO®/ VISION®

(LE, SE and VE Chairs)

OWNER’S MANUALORIGINAL INSTRUCTIONS

Continuum Footspas, LLC ● P.O. Box 363 Brookfield, WI 53008Toll Free: 1 877 255 3030 ● Telephone: 262 754 4900 ● Fax: 262 754 4901 ● MyContinuumPedicure.com

Pedicure Chairs fromContinuum® Pedicure Spas

Bravo/Vision Models - December, 2018

IntroductionThe entire team at Continuum® Footspas sincerely thanks you for choosing our pedicure chairs.We fully realize you had a choice and we look forward to making sure you made the right choice.A tremendous amount of time and energy has gone into designing and manufacturing not onlybeautiful looking pedicure chairs, but pedicure chairs that will perform trouble free for many years.

Throughout this manual, the phrase “Pedicure Chairs from Continuum Footspas”refers to Bravo® and/or Vision® Models. (LE, SE and VE Chairs).

Very Important Safety Instructions● The appliance is not to be used by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.● The live parts must be inaccessible to a person in the spa.● The floor has to be capable of supporting the expected load.● An adequate drainage system has to be provided to deal with overflow water.● If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.● This appliance can be used by children aged from 8 years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision orinstruction concerning use of the appliance in a safe way and understand the hazards involved.

● Children shall not play with the appliance.● Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V, must be

inaccessible to a person in the bath.● Parts incorporating electrical components, except remote control devices, must be located or fixed so that they

cannot fall into the bath.● The appliance must be supplied through a residual current device (RCD) having a rated residual operating

current not exceeding 30 mA.

● Maximum weight capacity of your pedicure chair is 325 pounds.

● Never bring or operate any electrical device in or near your pedicure chair.

● Always enter and exit your pedicure chair very slowly and carefully.

● NEVER STAND IN THE BASIN.

● Avoid excessive water temperatures. This can be dangerous and water

temperature must be checked before each use.

● Maximum operational water temperature should never exceed 105o F (41o C)

● Maximum supply water temperature should never exceed 150o F (65o C)

Always check state or local codes to verify maximum supply temperatures.

Please take a moment to read this entire Owners Manual before installation and use.

SAVE THESE INSTRUCTIONS

Continuum Pedicure Spas Limited WarrantyContinuum Footspas has designed and manufactured their pedicure chairs to the highest standards. Accordingly, Continuum Footspas express-ly warrants their pedicure chairs as follows:

To the original owner of our pedicure chairs, Continuum Footspas may repair or replace, at its option, any pedicure chairs found to be defectivein material or workmanship upon inspection by a factory authorized representative of Continuum Footspas.This limited warranty covers the following:

This Limited Warranty covers parts and components. It covers all Continuum Models for a period of one (1) year from date of shipment except asnoted below:● Maestro Model: Two (2) years from Date of Shipment (DOS). ● Glass Basin: One (1) year from DOS.● Pedicute/Simplicity: Heat & Vibration Basin Two (2)years from DOS.● Solid Surface Echo Basin: Five (5) years from DOS.● Maestro Solid Surface Basin: Five (5) years from DOS. ● SE Vibra-Massage + Heat System: Two (2) years from DOS.● LE Chair Only: Two (2) years from DOS. ● Replacement Parts (Non-Warranted): Ninety (90) days from DOS.● Fiberglass Basin: Two (2) years from DOS. ● Accessories: Ninety (90) days from DOS.● Shipping Costs Associated with Warranty Parts: One (1) year from date of shipment. Continuum will cover normal domestic shipping costs. Expedited and/or International shipping will incur additional charges .● Labor - All Models Except as Noted below: One (1) year from the date of shipment. Continuum Footspas will cover reasonable labor costsassociated with the installation of replacement parts found to be defective in material or workmanship upon inspection by a factory authorizedrepresentative of Continuum Footspas. NOTE EXCEPTIONS BELOW. No labor costs or replacement parts will be covered under this LimitedWarranty, if at the sole discretion of Continuum Footspas, it is determined a failure was caused by negligence, accident or improper use, improperinstallation or lack of proper maintenance as outlined in the Ownerʼs Manual.

The exchange of a pedicure chair is limited to supplying a replacement pedicure chair of equal style. Owner is responsible for all labor andshipping costs necessary to replace a pedicure chair.

NO CONSEQUENTIAL, INCIDENTAL, CONTINGENT, INDIRECT, SPECIAL OR OTHER DAMAGES WILL BE ALLOWED WHATSOEVER. Thislimited warranty is null and void if the pedicure chair is removed from its original installation, or is not installed in accordance with specificationsof Continuum Footspas, or national, state or local codes, regulations and ordinances. Furthermore, this Limited Warranty is null and void if thepedicure chair is subjected to improper installation or maintenance, negligence, improper cleaning or any other circumstances beyond ContinuumFootspas control. In order for your Limited Warranty to be valid, your pedicure chair must be installed by a licensed professional in accordancewith Continuum Footspas installation instructions.

EXCLUDED FROM LIMITED WARRANTY:1) Unauthorized repairs.2) Damage due to freight, accident, natural disaster and/or abuse.3) Staining, fading or discoloration of the seat, seat back, armrests, leg supports and footrests.4) Damage or malfunctions due to improper installation including but not limited to, failure

to comply with all national, state and local plumbing, electrical and building codes.5) Fading, discoloration or staining of any part due to improper water additives, hard water or harmful

cleaning agents or chemicals.6) Damage to drain pump due to obstruction in drain hose and/or debris in pump impeller housing.

Parts and/or circumstances for which Labor is NOT COVERED - Parts Noted Below Are Simple to Replace and DO NOT Require a ServiceTechnician.● Jet Cover and/or Impeller ● Faucet Cartridge and/or Filler-Sprayer ● Handheld Control Wands● Footrest/Leg Supports ● Roller Massage or Vibra-Massage + Heat System ● Manicure Trays● On/Off Air Actuated Button ● Any LED Light ● Replacement Upholstery● Pedicute Model ● Any International Shipments including but not limited to Canada and Mexico● Replacement of black plastic parts

For service or information regarding this limited warranty, please contact.

Continuum Footspas, LLC ● P.O. Box 363 Brookfield, WI 53008Toll Free: 1 877 255 3030 ● Telephone: 262 754 4900 ● Service: 262 777 2248 ● Fax: 262 754 4901 ● MyContinuumPedicure.com

This Limited Warranty is to the original owner and is not transferable. The original owner agrees by using Continuum pedicure chairs theobligation of Continuum Footspas shall not extend to indirect or contingent damages or injury. Furthermore, the obligations of Continuum Footspasare limited to those set forth herein. This limited warranty is the exclusive remedy and is in lieu of all other warranties, express or limited, includ-ing, but not limited to, any implied warranty of fitness or merchantability for a particular purpose. No distributor, dealer or other person has theright or authority to bind Continuum Footspas to changes to this limited warranty. Consequently, Continuum Footspas is not responsible forsuch warranties or representations.

ADDITIONAL PROVISIONS● Any assistance Continuum Footspas provides to the original owner above and beyond the scope

of this limited warranty does not constitute a waiver of such terms, limitations or exclusions. Furthermore,such assistance does not extend this Limited Warranty.

● Continuum Footspas shall not be liable for any other obligations or liabilities as a result of breachof contract of warranty, negligence or strict liability with regards to their pedicure chairs.

● This Limited Warranty applies only to pedicure chairs installed in any one of the fifty (50) States of the United States,the District of Columbia or provinces of Canada.

December, 2018


Very Important RequirementsEvery Continuum pedicure chair must be installed by a licensed plumber and licensed electrician.Installation must comply with all national, state and local building codes and/or regulations. Your pedi-cure chair will not operate properly unless it has sufficient water pressure and temperature, properdrainage and adequate electrical power.

ANY INSPECTIONS OR APPROVALS ARE THE SOLE RESPONSIBILITY OF THE PURCHASER.PRIOR TO INSTALLATION, ONE SHOULD CONTACT THEIR LOCAL BUILDING INSPECTOR TOMAKE SURE ALL LOCAL CODES ARE COMPLIED WITH.

WARNING!!!Possible Health Risks

Clients whose feet or legs are inflamed for any reason or clients who have open wounds should neverbe allowed to use a pedicure chair. If there is any sign of fungal infection, fracture, swelling or persist-ent pain, clients should consult their physician before using a pedicure chair. Diabetics should alwaysconsult their physician prior to receiving a pedicure.

If your client experiences any pain or discomfort while usingany Continuum pedicure chair, discontinue use immediately.



IMPORTANT UTILITY ANDINSTALLATION REQUIREMENTS AND

INSTRUCTIONS

Electrical Service - USAA separate, 120V, 60HZ, 15 amp GFCI protected grounded circuit MUST be used to supply power to eachpedicure chair. Failure to do so renders the Limited Warranty null and void.Electrical Service - InternationalA separate, 220V, 50HZ, 15 amp GFCI protected grounded circuit MUST be used to supply power to eachpedicure chair. Failure to do so renders the Limited Warranty null and void.

NOTE: IF INSTALLED IN CANADA THIS UNIT MUST BE IN ACCORDANCE WITHTHE CANADIAN ELECTRICAL CODE, PART 1.

Grounding and GFCI RequirementsWARNING - When using electrical products, basic precautions should always be followed, includingthe following:

1. DANGER: RISK OF ELECTRIC SHOCK. Connect ONLY to a circuit protected by a ground-faultcircuit-interrupter (GFCI).

2. GROUNDING IS REQUIRED. Every Continuum pedicure chair MUST be installed by a licensedelectrician and MUST be properly grounded.DO NOT IN ANY WAY MODIFY THE PLUG PROVIDED ON YOUR PEDICURE CHAIR.NEVER USE A NON-GROUNDED ADAPTER WITH ANY CONTINUUM PEDICURE CHAIR.

WARNING:TO REDUCE THE RISK OF BURNS, ELECTRIC SHOCK, FIRE OR INJURY TO PERSONS:

● Any servicing of your pedicure chair must be performed by authorizedservice personnel only.

● DO NOT operate your pedicure chair if it has a damaged cord or plug.● Keep cord away from heated surfaces.● DO NOT use outdoors.

Hot/Cold Water Supply and Drain● All plumbing connections must conform to all national, state and local codes.● Shut-off valves are strongly recommended per plumbing codes.● Maximum water temperature must not exceed 105o F (41o C)● Maximum SUPPLY water temperature must not exceed 150o F (65o C)● Hot/Cold water supply and drain connections are located in the back of pedicure chair.● When utilizing optional factory installed drain pump, in-line backflow prevention is provided.● If pedicure chair is plumbed utilizing drain pump and drain hose; the drain hose

connecting the pedicure chair to the wall connection (drain) must be 3/4” ID.● Size of supplied plumbing fittings:

Hot/Cold water supply: 1/2” NPT (male)Drain Pump: 3/4” NPT (male)



Instructions Pertaining to aRisk of Fire, Electric Shock or Injury to Persons

Important Safety Instructions

WARNING - When using Continuum pedicure chairs, basic precautions MUST be followed, includ-ing the following:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING. CHILDREN SHOULD NOT USEPEDICURE CHAIRS WITHOUT ADULT SUPERVISION.

3. Use your pedicure chair only for its intended use as described in this manual.Do not use attachments not recommended by the manufacturer.

4. WARNING: RISK OF ELECTRIC SHOCK. DO NOT PERMIT ELECTRIC APPLIANCES (SUCHAS A HAIR DRYER, LAMP, TELEPHONE, RADIO, OR TELEVISION) WITHIN 5 FEET (1.5 M)OF YOUR PEDICURE CHAIR.

5. Do not operate your pedicure chair without the jet cover attached to the Jet.

6. Any Continuum pedicure chair must be connected only to a supply circuit that is protected bya ground fault circuit-interrupter (GFCI). Such a GFCI should be provided by the installerand should be tested on a routine basis. To test the GFCI, push the test button. The GFCIshould interrupt power. Push the reset button. Power should be restored. If the GFCI fails tooperate in this manner, the GFCI is defective. If the GFCI interrupts power to the pedicure chairwithout the test button being pushed, a ground current is flowing, indicating the possibility ofan electric shock. Do not use your pedicure chair. Disconnect the pedicure chair and have theproblem corrected by a qualified service representative before using.

7. GROUNDING IS REQUIRED. Your pedicure chair MUST be installed by a qualified licensedelectrician and MUST be properly grounded. DO NOT IN ANY WAY MODIFY THE PLUGPROVIDED ON YOUR PEDICURE CHAIR. NO ADAPTER SHOULD BE USED WITHYOUR PEDICURE CHAIR.

8. SAVE THESE INSTRUCTIONS.

WARNINGAny service that may be required MUST be performed by a qualified service representative.


Install to Permit Access for ServicingIn order to ensure access after installation, please refer to installation drawings available atMyContinuumPedicure.com.

It is strongly recommended that each unit (each pedicure chair) be properly secured to the floor.Securing the unit to the floor is the sole responsibility of the purchaser and/or the qualified installer. This isespecially important if the unit is gravity drained with or without an air gap. The Limited Warranty maybecome null and void if a unit is not properly secured to the floor.

Location and SupportThe floor structure must be level and capable of supporting the occupied pedicure chair.Refer to installation drawings at MyContinuumPedicure.com

Extremely Important

EVERY CONTINUUM PEDICURE CHAIR MUST BE INSTALLED BY A LICENSED PLUMBER AND A LICENSED ELECTRICIAN.INSTALLATION MUST COMPLY WITH ALL NATIONAL, STATE AND LOCAL BUILDING CODES AND/OR REGULATIONS. FAILURETO COMPLY WITH THESE CODES AND/OR REGULATIONS WILL RESULT IN THE LIMITED WARRANTY BEING NULL AND VOID.

UnpackingContinuum pedicure chairs require very little assembly.Remove and discard all packing and lifting materials.

Installation Instructions


YOU ARE REQUIRED TO CHECK WITH YOUR STATE BOARD FOR MANDATORYCLEANING AND DISINFECTING REQUIREMENTS AND PROCEDURES.The following procedures are important guidelines that will help in keepingyour pedicure chair clean and trouble free for years. It is extremely importantto clean and disinfect each and every pedicure chair after each pedicure andafter the last pedicure of the day.

A SPECIAL NOTE PERTAINING TO BLEACHWhile bleach seems to be used extensively for cleaning and disinfecting ofpedicure chair basins, it is NOT recommended nor is it effective. Moreover,excessive use of bleach may greatly reduce the longevity of your pedicurechair internal components (i.e. pumps, jet, waste assembly, etc.). Excessiveand repeated use of bleach may also void your warranty. As always, you arerequired to check with your state board for mandatory cleaning anddisinfecting requirements and procedures.Cleaning and Disinfecting ProductsYour state board requires disinfecting of your pedicure basin. Continuumrecommends “Splish Splash One-Step Disinfectant.” The following pageoutlines the benefits of Splish Splash together with contactinformation.While other EPA registered products are available for maintaining pedicuretubs, we have found Splish Splash to be the most effective, multi-purposeand economical product on the market.

IMPORTANT

User Maintenance InstructionsCleaning and Disinfecting


After Each Client &End of Each Day Cleaning Procedures

The removable wet-end assembly MUST be placed onto the motor housing in thecorrect position or the jet may be damaged. The wet end housing must fit in the propergroove onto the motor housing. If the wet end is not positioned correctly, damage to thejet may occur due to misalignment. This will NOT be covered by any Continuumwarranty. Never turn the jet on without adequate water in the basin. There must be atleast one (1) inch of water above the motor housing.

1. Drain all water from the basin.2. Remove the Wet End consisting of the cover, impeller, and housing from the jet. No tools are required. Simply pull the

wet end away from the jet. Make sure motor has completely stopped. Twist the cover from the housing to expose theimpeller.

3. Clean all 3 wet end parts with a brush, liquid soap and water to remove all visible residue. Reattach all 3 parts to themotor housing. Make sure the wet end is placed in the proper groove on the jet housing.

4. Fill the basin with warm water and circulate the correct amount of the EPA Registered Liquid Disinfectant(Splish Splash is strongly recommended) through the basin for 10 minutes.Scrub all visible residue from the inside walls of the basin with a sponge/soft brush. Brushes must be cleaned anddisinfected after each use.

5. Drain the water and rinse the basin; wipe dry with a clean paper towel.

THE ABOVE SHOULD BE FOLLOWED EVEN IF TUB LINERS ARE USED.Note:The use of oil based products can build up in the whirlpool system causing clogging inthe jet and build up onto the surface of the basin. Adherence to the above cleaning willminimize build up thus the manufacturer recommend not to use mineral oil basedproduct.

YOUR ARE REQUIRED TO CHECK WITH YOUR STATE BOARD FORMANDATORY CLEANING AND DISINFECTING REQUIREMENTS AND PROCEDURES.


Care and MaintenanceIMPORTANT NOTE: Never use abrasive cleaners or pads on any part of the pedicure unit.

Fiberglass Finishes (including basins)Fiberglass finishes require very little maintenance. If any harsh chemicals come in contact with the fiberglass finish, it isimportant to wipe clean as quickly as possible. Do not allow chemicals (i.e. nail polish, acetone, cuticle remover) to dry onfiberglass surfaces.

If one desires to polish the gel-gloss finish (fiberglass finish), one can purchase “Gel Gloss” or “Novus Polish” at mosthardware stores. Read and follow manufacturer’s instructions.

Basin-Acrylic/Capped/FiberglassDo NOT use abrasive pads or cleaners on any surface. Wipe clean with a sponge or soft brush. Follow Stateʼs cleaningand disinfecting procedures.

Glass BasinThe “Bravo” model features a tempered, high-strength glass basin. While it is quite thick, it can crack if an object, i.e. amassage stone, is dropped into the basin. (This damage is NOT covered under the Limited Warranty) Reasonable caremust be taken when using the glass basin.Do NOT use abrasive pads or cleaners on glass surfaces or any chrome surfaces.Follow all State Rules and Regulations with regards to cleaning and sanitation.

UpholsterySimply use a mild detergent (very little) with warm water and gently clean any dirt or grime that may appear on the seat, seatback or arms. The leather-like material is very durable and with reasonable care should look like new for many years.Stains from customers garment are not covered under warranty.

FootrestsA mild detergent and warm water is all that is needed to clean the padded leg supports. Howevercare should be taken to prevent nail polish or acetone from coming in contact with the leg supports. These productsmay damage or discolor the outer “skin” of the foam.In spite of taking necessary precautions to protect the leg supports, hard water and/or certain products many causethe black footrests to develop a white film or some discoloration. If this occurs, a product called “Black Max”-Vinyl andRubber Dressing works well to restore the leg supports. Black Max can be purchased at most hardware stores oronline.

Massage SystemsSE Chair: The massage system is located in the back portion of the chair. It is accessible by unzipping thezipper located on the back or side of the chair. This allows for removal of the upholstered chair cover andaccess to the four (4) motor plus heating pad Vibra-massage system.

LE and VE Chairs: The massage mechanisms on the LE and VE chairs require little maintenance. However,since it is a “Full Function” system there are more parts that may need lubrication or service eventually. If themechanism becomes excessively noisy, a very little light grease may be applied to the tracks. Massage mech-anism may be accessed by the front of the LE model and by the back of the VE model.

CAUTION: Make sure grease never comes in contact with pulley belts as they will becomeslippery and fail.

NOTE: VERY IMPORTANT!Both LE and VE Chairs use rather complex rolling and kneading mechanisms. Under normal use, theserolling and kneading mechanisms may cause the foam and protective fabric to wear thin. This is perfectlynormal. However, to prevent serious damage to the mechanism, one must check for normal wear and tearat least every (6) six months. If foam and/or fabric is wearing thin, immediately contact ContinuumFootspas for replacements.


OPERATING PRECAUTIONSNOTE: Please read these instructions carefully before operating your pedicure chair.

CAUTION: To avoid injury and irreparable damage, always remain seated when using your pedicurechair. NEVER STAND ON OR IN THE BASIN.

SPECIAL WARNINGS

● If you have any concerns regarding your health, consult your doctor before using your pedicurechair.

● Never use any pedicure chair on open wounds, or any area of the body that is swollen, burned,inflamed or where skin eruptions or sores are present.

● Consult your doctor before using a pedicure chair if you have diabetes, as diabetes cancontribute to foot problems including decreased feeling or circulation to the feet.

● Use of this product should be pleasant and comfortable. Should pain or discomfort result,discontinue use and consult your physician.

WARNING: WHEN USING CONTINUUM PEDICURE CHAIRS, BASIC PRECAUTIONSSHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. DANGER: To reduce the risk of injury, do not permit children to use pedicure chairs unless theyare closely supervised at all times.

3. Use your pedicure chair only for its intended use as described in this manual. Do not useattachments not recommended by manufacturer. Do not tamper with your pedicure chair.

After your pedicure chair is installed and the plumbing and electrical connections are made,clean and disinfect the basin before initial use.

YOU ARE REQUIRED TO CHECK WITH YOUR STATE BOARD FORMANDATORY CLEANING AND DISINFECTING REQUIREMENTS AND PROCEDURES.


LE, VE and SE CHAIRSASSEMBLY INSTRUCTIONS

Step #1) The back portion of the LE, VE or SE chair is shipped facing down. The backs are held in place during shippingby four (4) plastic ties. Cut all plastic ties and gently move the chair into an upright position, making sure the back remainslocated in the pivot grooves.

FIGURE 1

Step #2) Once the chair back is in an upright position, locate the latchat the bottom of the back. (See Figure 1) This latch connects the chairback to the seat base. Located under the seat base is an actuatorwith a short, steel connecting pin. (See Figure 2) In order toengage this pin and latch, this pin MUST remain in a perfectlyhorizontal position. (See Figure 2 once again) This is very importantas it will be impossible to engage the latch and pin if the pin is not ina horizontal position. Gently move the chair back until the pinengages into the latch. Since the latch utilizes a spring, you willhear a click when they are properly connected.

If it ever becomes necessary to disconnect the chair back from the seat base,simply press the lever on the latch to disconnect. FIGURE 2 (LE or SE Version)

FIGURE 3


RED

WHITE

LE Chair

Step #3) Plug the two (2) wire connectors together (LE version only). They are located nearthe back of the chair. Connect both white connectors together and both red connectorstogether. (See Figure 3)

Step #4) Locate seat bottom cushion. Place it on the seat base making sure itʼs as farback as possible and even from side to side. This seat cushion is held in place with Velcro.There should be no visible gaps between the seat cushion and the back cushion.

Important Notes (LE & VE Version Only):● Do not discard the extra chair fuses in the plastic bag. They are replacements if needed.

● To raise manicure trays, simply move them to a horizontal position until you hear a clickthat locks the tray in place. To lower trays, press up on the lever located at the end of thesupport bracket and at the same time; gently push the tray upward to disengage the latch.

Important Notes (LE Version Only):● To increase overall intensity of massage, simply unzip the seat back cushion and

remove the 1” thick foam insert between the rolling mechanism and the cushion. The foaminsert is held in place with Velcro.

● Re-position client with the tech button located on the front area by the footrest.

VE Chair Back Attachment


SE Chair

The SE Chair features a four (4) motor Vibra-Massage + Heat system. All four motors are located in thelower to middle back of the chair. The heating pad is located in the lumbar back area. All motors andheating pad are controlled with a hand-held control wand.

The VE Chair utilizes a clevis pin and a locking hitch pin. The holes located in the seat back frame are linedup with the seat bottom, the clevis pin is inserted through the holes and secured with the hitch pin.

Clevis PinHitch Pin

Frame

Operating Instructions for massage system:

Massage: Press POWER or either ZONE key to turn massageON. Press again to turn massage OFF.

Timer: Press and hold POWER key to change timer from 15to 30 mins. (Green light indicates 15 mins. Amber lightindicates 30 mins.)

Zone: Press Zone 1 or 2 keys to turn either zone ON or OFF.

Select / Wave / Pulse: Press Select, Wave or Pulse keys tochoose massage type

Intensity +/-: Press + or - keys to increase of decreasemassage intensity

Speed +/-: Press + or - keys to increase or decrease themassage speed (PULSE and WAVE modesonly)

Heat: Press LO: Low Heat (Amber Light). Press HI: HighHeat (Red Light). Press either again to turn off. Works withmassage or independently. 30 mins timer.

Note: Only use the power supply furnished with the unit.

Operational SummaryTechnician Operated Controls/Features

FILLING/SPRAYINGLocate the chrome hot/cold water valve handle on the front or side of your pedicure chair. This valve handlecontrols both the flow of water and the temperature of water. Note: The sprayer/filler has a dual function; itis both a sprayer and filler for the basin.

TO FILLLIFT AND TURN water valve handle, adjust water temperature and flow. When desired water temperature isachieved, close “Pop-Up” in bottom of basin by turning chrome drain handle located on right side of base.

When water level reaches a point approximately one (1) inch ABOVE the top edge of the jet, shut water off bypressing down on handle.Note: The Jet MUST be fully submerged in water before operating .NEVER TURN JET ON WITHOUTWATER.

TO DRAINWith optional factory installed drain pump:Step 1) Gently turn chrome drain handle located on the base.

This activates “Pop-Up” located on bottom of basin allowing water to drain.

Step 2) Wait for the air bubbles to exit. Press chrome button marked “DRAIN.”This will activate drain pump. When basin is fully emptied, press button once again toturn pump off. VERY IMPORTANT! When draining basin, ALWAYS perform Step 1 before Step 2.NEVER reverse the steps as this may cause the pop-up to become jammed in thewaste assembly.

Note: Drain pump will automatically turn off in four (4) minutes if button is not pressed asecond time.

GRAVITY DRAINStep 1) Gently turn chrome drain handle located on right side of base.

This activates “Pop-Up” located on bottom of basin allowing water to drain.

HANDHELD SHIATSU MASSAGE CONTROL WAND (LE and VE Models Only)Use the handheld control wand to turn the chair on/off, move the chair forward/backward and recline. It alsocontrols all the various massage functions and features.The SE version chair has two (2) control wands. One controls the seat movements (forward/backward/recline);the other to control the Vibra-Massage + Heat system.

Cleaning and Disinfecting after DrainingYOU ARE REQUIRED TO CHECK WITH YOUR STATE BOARD FOR MANDATORY CLEANING

AND DISINFECTING REQUIREMENTS AND PROCEDURES.

WARNING: It is extremely important to follow the cleaning instructions provided by your StateBoard. Failure to clean your pedicure chair adequately can result in serious health issues for yourclients as well as the nail technician. Failing to clean your pedicure chair may also cause it to workimproperly. Regular cleaning will keep your pedicure chair in good working condition.



Jet SystemThe pipeless “magnetic” system is standard in your pedicure unit. After basin is filled to proper level,turn jet on by pressing the chrome button marked “JET”. To turn off, press “JET” button a second time.

CAUTION:

The removable wet-end assembly MUST be placed onto the motor housing in the correct positionor the jet may be damaged. The motor housing and the wet end housing must fit in the propergroove. If the wet end is not positioned correctly, damage to the jet may occur due tomisalignment. This will NOT be covered by any Continuum warranty. Never turn the jet on withoutadequate water in the basin. There must be at least one (1) inch of water above the motorhousing.

NOTE:Liners can be used on a “magnetic” system. The liner has to sit between the motorhousing and the wet end assembly.

PLEASE NOTE:Pedicure chairs assembled and shipped during Wisconsin winter months are tested using a pinkRV anti-freeze solution. It is perfectly normal for a small amount of this pink fluid to remain withinthe plumbing system. To eliminate any traces of RV anti-freeze, simply fill and operate yourpedicure chair several times before actual use.

ATTACHING MANICURE TRAYS (SE Chair Model Only)Optional manicure trays are available. Note: Manicure trays are included on all LE and VE Chairs.If manicure trays are ordered with your pedicure chair, brackets may be factory installed. Simplyattach the trays with provided wood screws making sure they fit tightly against upholstered arms.

WARNING: DO NOT ATTEMPT TO OPERATE JET WITHOUT WATER!

continuum pedicure spas

Documents