control-matched drives and motors allen-bradley … scrambler drive - dc integrated ... 59 fla...

Allen-Bradley offers the broadest selection of drive and motor packages designed for optimum variable-speed performance, service life and value. These Control-Matched drive and motor packages are a result of the practi-cal application of advanced electrical/electronic technology – backed by decades of application experience in virtually every industry. For additional information refer to our web site: www.controlmatched.com

Control-MatchedTM

Drives and MotorsFor Optimum Variable-Speed Value

www.rockwellautomation.com

Corporate HeadquartersRockwell Automation, 777 East Wisconsin Avenue, Suite 1400, Milwaukee, WI, 53202-5302 USA, Tel: (1) 414.212.5200, Fax: (1) 414.212.5201

Headquarters for Dodge and Reliance Electric ProductsAmericas: Rockwell Automation, 6040 Ponders Court, Greenville, SC 29615-4617 USA, Tel: (1) 864.297.4800, Fax: (1) 864.281.2433Europe/Middle East/Africa: Rockwell Automation, Herman-Heinrich-Gossen-Strasse 3, 50858 Köln, Germany, Tel: 49 (0) 2234 37941252, Fax: 49 (0) 2234 3794164Asia Pacifi c: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong, Tel: (852) 2887.4788, Fax: (852) 2508.1846

Headquarters for Allen-Bradley Products, Rockwell Software Products and Global Manufacturing SolutionsAmericas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414.382.2000, Fax: (1) 414.382.4444Europe/Middle East/Africa: Rockwell Automation SA/NV, Vorstlaan/Boulevard du Souverain 36, 1170 Brussels, Belgium, Tel: (32) 2 663 0600, Fax: (32) 2 663 0640Asia Pacifi c: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong, Tel: (852) 2887 4788, Fax: (852) 2508 1846

This material is not intended to provide operational instructions. Appropriate Rockwell Automation instruction manuals and precautions should be studied prior to installation, operation or maintenance of equipment.

Copyright © 2005 Rockwell Automation, Inc. All rights reserved. Printed in USA.

RAPS-1348 3/05-7.5M-K

Allen-Bradley

Control Matched

Motor Catalog

Allen

-Bradley C

ontrol M

atched M

otor Catalog

M

arch 2005

NOTES

1 F-1 mounting

2 1.0 Service Factor

3 Not suitable for use on motors with model number with a, b, or c suffi xes

4 Wye start, Delta run

5 Belted duty only, roller bearing

6 F-2 mounting

7 Companion voltages not available

8 TENV motors are capable of 20:1 speed range operation on drives with no back diode.

9 Motors are not NAFTA qualifi ed

10 These motors meet the hardware requirements of IEEE 45/ABS and are not provided with Marine Plan Documentation

11 Price includes XT features and explosion proof prices include drain on drive end

12 Does not meet NEMA BA for C-Face Footed Motors

13 Furnished without conduit box. Order kit P/N K56G3230

14 Type CH

15 Motors rated 208 - 230/460 are operable to minimum 200 volts

16 Standard TENV motor with standard lead length

17 Class B insulation, 1.0 service factor



20 Class F insulation

21 Double bolt

22 Base used for NEMA & above NEMA frames, 445T

23 Two piece slide rails

24 Includes terminal board

25 Production only after stock depleted. To be superseded by V*S Master Motor

26 See OMS

27 Kits include textile fan cover with drip cover mounted. Suitable for TEFC or TEFC-XT foot and footless design only (not XP or O

28 5.5 inch frame - Aluminum end shield standard enclosure


30 Motors usable on 208 volts @ specifi ed amps

31 Suitable for 230/460, 60Hz and 190-220/380-440 volts, 50Hz

32 Stearns brake

33 Reliance AC brake

34 Dodge D series brake

35 Design A, also meets Design E inrush limits

36 1.0 Service factor when operated at 50Hz

37 Derate horsepower 20% when operated at 50hz

38 Consists of sleeve and key to convert 1/2 shaft to 5/8 shaft

39 Coupled Duty only, TS shaft

40 Includes tachometer, stab shaft and mounting hardware

41 Will mount any tachometer having standard NEMA 56 C-face and shaft extension

42 DODGE Short Series Brake

43 Cannot be mounted vertically

44 Scrambler drive - DC integrated control and motor product

45 Maximum value

46 No key - 1.25 long fl at

47 BA dimension does not meet NEMA standards

48 Includes phase insulation. Suitable for inverter duty

49 Includes vertical lifting provision

50 Cast Iron 140 Frame

51 BISSC certifi ed

53 Mounting hole diameter

54 For single phase ratings: O = 7.31: Z = 12.80

55 Refer to previous dimension pages

56 48 through 140T frame ratings are typical full load effi ciency, not nominal effi ciency

57 56 through 140T frame performance data is valid for TENV or TEFC. 180T and larger frame performance data is valid for TEFC ONLY

59 FLA includes harmonic content from PWM power supply

61 TENV motors have a constant torque speed range from 0 to base speed

62 TENV motors have provisions for tachometer mounting as standard

65 Will fi t standard effi cient F model numbers ONLY

71 Nominal effi ciency is base at the 1800 RPM (High RPM) and low speed effi ciency is available just not published

72 Orders shipped from a Rockwell Automation facility in 5 working days. Motor is returnable for a restocking charge of $100 plus

73 Can only be used on motors 1800 RPM and slower with ball bearings

75 Availability limited to current stock

77 Buying motors not manufactured by Rockwell Automation may cause loss of sleep

79 Motor mounted blower is located on drive end

80 Motor has thermostat and provisions for adding fl ange mtd. tach

81 Motor has thermostat and provisions for adding adapter mtd. tach

82 Motor is force ventilated and supplied with blower, and fi lter.

83 May be operated on 50 Hz rectifi ed power supply with full nameplate rating. AC supply voltage must be same as 60 Hz supply; i.e

84 May be operated on 50 Hz rectifi ed power supply with full nameplate rating only when motor is force ventilated with motor mount

85 Cannot be operated at full nameplate rating on 50 Hz rectifi ed power supply

86 Winder Duty - 100% load for 1 minute at 3000 RPM, straight shunt design. Includes blower without fi lter. Tachometer is rated at

87 Motor has thermostat and provision for adding integral AC or DC tachometer or adapter mounted tachometer.

88 Motor is force ventilated and supplied with blower.

89 Motor is force ventilated and supplied with single-phase blower motor rated 1/3 HP, 3450/2850 RPM, 115/230 volts, 60/50 Hz.

90 Includes thermostat

91 Includes Dynapar H20 1024 PPR encoder with mating 10 pin MS connector. Requires 2-7 business days.

92 Blower is piggyback mounted on L440 frames

93 180TC NEMA fl ange size, see appropriate dimension sheet.

94 210TC NEMA fl ange size, see appropriate dimension sheet


96 See appropriate dimension sheet for fl ange size

99 Highlighted for Marketing Review

100 Ball bearing only

101 Not available for Easy Clean product line

102 Not available for XT enclosures

103 Not available for Non-NAFTA motors

104 Not available for 841 XL motors

105 Not available on SABRE and CALIBRE product lines

106 Finned aluminum frame construction

107 Not available on belted duty motors and/or motors with roller bearings

121 Motor is rated for F rise 1000:1 Constant Torque Range, and F Rise 4:1 Constant Torque Range

122 Motor rated for only F rise 4:1 Constant Torque Range

Note - All motors highlighted in ROSE are cast iron frames

Vers

ion

Vers

ion

Not

e- C

ontro

lled

by P

assp

ort

See

Vers

ion

Not

es fo

r Rev

isio

n Ch

ange

s

Bul

letin

CM10

0Co

mpo

nent

Cla

ss -

Inve

rter D

uty

CM20

0Ar

chite

ctur

e Cl

ass

- Vec

tor D

uty

CM30

0Si

ne W

ave

Clas

s

Encl

osur

e

DGDP

G - D

rip-P

roof

Gua

rded

FVDP

G-FV

- Dr

ip-P

roof

Gua

rded

For

ce V

entil

ated

DPOD

P - O

pen

Drip

-Pro

of

AOTE

AO -

Tota

lly E

nclo

sed

Air O

ver

BCTE

BC -

Tota

lly E

nclo

sed

Blow

er C

oole

d

FCTE

FC -

Tota

lly E

nclo

sed

Fan

Cool

ed

NV

TEN

V - T

otal

ly E

nclo

sed

Non

Ven

tilat

ed

AATE

DC A

/A -

Tota

lly E

nclo

sed

Dual

Coo

led

Air t

o Ai

r

AWTE

DC A

/W -

Tota

lly E

nclo

sed

Dual

Coo

led

Air t

o W

ater

Bul

letin

Encl

osur

e

Hor

sepo

wer

Bas

e Sp

eed

V

olta

ge

Ef

fi cie

ncy

C

T or

VT

Requ

ired

Mou

ntin

g

Fin

al D

escr

ipto

r

Ver

sion

Alle

n-B

radl

ey C

ontr

ol M

atch

ed M

otor

s Ca

talo

g St

ring

Dec

oder

Hor

sepo

wer

HP a

s lis

ted

025

25 H

orse

pow

er

Not

e “F

” is

use

d fo

r a d

ecim

al p

oint

030

30 H

orse

pow

er

F17

0.17

Hor

sepo

wer

040

40 H

orse

pow

er

F25

0.25

Hor

sepo

wer

050

50 H

orse

pow

er

F33

0.33

Hor

sepo

wer

060

60 H

orse

pow

er

0F5

0.5

Hors

epow

er07

575

Hor

sepo

wer

F75

0.75

Hor

sepo

wer

100

100

Hors

epow

er

001

1 Ho

rsep

ower

125

125

Hors

epow

er

1F5

1.5

Hors

epow

er15

015

0 Ho

rsep

ower

002

2 Ho

rsep

ower

200

200

Hors

epow

er

003

3 Ho

rsep

ower

250

250

Hors

epow

er

005

5 Ho

rsep

ower

300

300

Hors

epow

er

7F5

7.5

Hors

epow

er35

035

0 Ho

rsep

ower

010

10 H

orse

pow

er40

040

0 Ho

rsep

ower

015

15 H

orse

pow

er45

045

0 Ho

rsep

ower

020

20 H

orse

pow

er50

050

0 Ho

rsep

ower

1K0

1000

Hor

sepo

wer

Bas

e Sp

eed

As n

oted

- fi r

st tw

o di

gits

of b

ase

spee

d

0550

0 RP

M12

1200

RPM

0665

0 RP

M15

1500

RPM

0772

0 RP

M17

1750

RPM

0885

0 RP

M18

1800

RPM

0990

0 RP

M25

2500

RPM

1010

00 R

PM35

3550

RPM

1111

50 R

PM36

3600

RPM

Volta

ge

F23

0 Vo

lt, 3

Pha

se, 6

0 Hz

L18

0 V

Arm

, 100

/200

V F

ield

, Str

Win

ding

D38

0 Vo

lt, 3

Pha

se, 5

0 Hz

M24

0 V

Arm

, 150

V F

ield

, Str

Win

ding

E40

0 Vo

lt, 3

Pha

se, 5

0 Hz

N24

0 V

Arm

, 240

V F

ield

, Str

Win

ding

B46

0 Vo

lt, 3

Pha

se, 6

0 Hz

Q50

0 V

Arm

, 300

V F

ield

, Str

Win

ding

C57

5 Vo

lt, 3

Pha

se, 6

0 Hz

P50

0 V

Arm

, 150

/300

V F

ield

, Sta

b W

indi

ng

R23

00 V

olt,

3 Ph

ase,

60

HzT

240

V Ar

m, 1

50 V

Fie

ld, S

tab

Win

ding

S41

60 V

olt,

3 Ph

ase,

60

HzU

240

V Ar

m, 2

40 V

Fie

ld, S

tab

Win

ding

H20

0/20

8 Vo

lt, 3

Pha

se, 6

0 Hz

V50

0 V

Arm

, 300

V F

ield

, Sta

b W

indi

ng

G20

8-23

0/46

0 Vo

lt, 3

Pha

se, 6

0 Hz

W90

V A

rm, P

M F

ield

A23

0/46

0 Vo

lt, 3

Pha

se, 6

0 Hz

J18

0 V

Arm

, PM

Fie

ld

K90

V A

rm, 5

0/10

0 V

Fiel

d

Effi c

ienc

y

EEn

ergy

Effi

cien

t - M

eets

EPA

ct R

equi

rem

ents

SSt

anda

rd E

ffi ci

ent

NN

EMA

Prem

ium

PPr

emiu

m E

ffi ci

ent

XN

ot A

pplic

able

CT o

r VT

requ

ired

HCT

10:

1Co

nsta

nt To

rque

10:

1 Sp

eed

Rang

e

ZCT

100

0:1

Cons

tant

Torq

ue 1

000:

1 Sp

eed

Rang

e (0

to B

ase

Spee

d)

JCT

2:1

Cons

tant

Torq

ue 2

:1 S

peed

Ran

ge

JCT

2:1

(10)

Cons

tant

Torq

ue 2

:1 S

peed

Ran

ge (c

apab

le o

f 10:

1 CT

with

fan

chan

ge)

MCT

20:

1Co

nsta

nt To

rque

20:

1 Sp

eed

Rang

e

KCT

4:1

Cons

tant

Torq

ue 4

:1 S

peed

Ran

ge

KCT

4:1

(10)

Cons

tant

Torq

ue 4

:1 S

peed

Ran

ge (c

apab

le o

f 10:

1 CT

with

fan

chan

ge)

Xna

Not

for u

se o

n in

verte

r pow

er

VVT

10:

1Va

riabl

e To

rque

10:

1 Sp

eed

Rang

e

VVT

10:

1 (2

)Va

riabl

e To

rque

10:

1 Sp

eed

Rang

e (c

apab

le o

f 2:1

CT

with

fan

chan

ge)

Mou

ntin

g

CC-

Face

Foo

t Mou

nted

FC-

Face

Foo

tless

HFo

ot M

ount

ed

UFo

ot M

ount

ed, R

olle

r Bea

ring

Fina

l Dis

crip

tor

414

0 Fr

ame

Mot

or

556

Fra

me

Mot

or

818

0 Fr

ame

Mot

or

ICa

st ir

on F

ram

e

NN

on-c

ast i

ron

fram

e

STS

sha

ft le

ngth

TN

ema

T sh

aft l

engt

h

This

tool

sho

uld

ON

LY b

e us

ed to

DEC

OD

E ex

istin

g ca

talo

g st

ring

s.

It CA

NN

OT

be u

sed

to c

reat

e a

new

par

t num

ber.

Allen Bradley Control Matched Motors

Table of Contents

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Table of Contents

GENERAL INFORMATION

Efficiency Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Agency Approvals/Certifications/Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cancellation Charges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Freight Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warranty Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Motor Selection and Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Conduit Box Location Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Evaluation of Motor Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rush/Breakdown Order Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sales Order Change Charges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rockwell Automation Motor Service Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Return Policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RAISE Software File Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

COMPONENT CLASSFor use on inverter for variable torque and constant torque (less than 10:1) applications,no encoder capability, 3 NC thermostats included

INVERTER DUTY GENERAL PURPOSE SERIESCM101 – Enclosed Energy Efficient Rolled Steel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Most Economical Inverter Capable, Totally Enclosed Motor 10:1 VT and 2:1 CT Capability

CM102 – Enclosed Energy Efficient Cast Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Most Economical Inverter Capable, Cast Iron Totally Enclosed Motor 10:1 VT and 2:1 CT Capability

CM103 – Totally Enclosed Energy Efficient, Premium Efficient, and NEMA Premium . . . . . . . . . . . . Designed for General Purpose Applications10:1 VT and varying CT Capability

CM106 – Open Energy Efficient Rolled Steel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Most Economical Inverter Capable, Open Motor Available, 10:1 VT and 2:1 CT Capability

CM107 – Open Energy Efficient, Premium Efficient, NEMA Premium . . . . . . . . . . . . . . . . . . . . . . . . . General Purpose Open motors10:1 VT and 2:1 CT Capability

Table of Contents - Allen Bradley Control Matched Motors

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

1

1

3

3

4

5

9

10

12

12

12

13

13

13

14

18

22

32

35

HARSH DUTY HARSH ENVIRONMENT SERIESCM111 – Severe Duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Designed with features for long life in severe environments such as chemical plants, petroleum refineries, and paper mills10:1 VT and varying CT Capability

CM112 – IEEE 841 XL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exceeds IEEE841 mechanical requirementsBuilt extra tough for durability in harsh environments10:1 VT and varying CT Capability

CM113 – Aggregate Duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Designed with high starting torque and break down torque for heavily loaded conveyor and crusher applications10:1 VT and varying CT Capability

CM115 – Wash Down Duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Designed for service in wash down applications subject to sanitary codes, IP5510:1 VT and varying CT Capability

CM118 – Stainless Steel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Designed for use in food or chemical applications where painted motors are undesirable, IP5510:1 VT and varying CT Capability

CM100 KITS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ARCHITECTURE CLASSFor use on inverter only for high performance applications, encoder capable, 3 NC thermostats included

INDUSTRIAL ENVIRONMENT SERIESCM201 – Vector Duty Enclosed Small AC Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1000:1 CT Capable, TENV and TEFC Enclosures

CM202 – Vector Duty Totally Enclosed Cast Iron NEMA AC Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000:1 Capable, TEFC and TENV Enclosures

CM202 KITS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CM203 – Vector Duty Laminated AC Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000:1 Capable; DPFV, TEBC, TENV, and TEFC Enclosures

CM203 KITS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CM205 – DC Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Designed with laminated square frame for more performance in smaller framesDPG-FV and TEFC enclosures

CM205 KITS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CM206 – Small DC Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Designed for reliability and long life in variable speed applications TEFC and TENV Enclosures


General

Information

CM

100C

M 200

CM

300F

ootnotes

39

49

54

57

62

65

73

76

82

83

106

111

120

123

SINE WAVE CLASSFor use on sine wave power for fixed speed applications such as conveyors, blowers, pumps or fans

GENERAL PURPOSE SERIESCM301 – Enclosed Energy Efficient Rolled Steel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Most Economical Totally Enclosed Motor

CM302 – Enclosed Energy Efficient Cast Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Most Economical Cast Iron Totally Enclosed Motor

CM303 – Totally Enclosed Energy Efficient, Premium Efficient, and NEMA Premium . . . . . . . . . . . . Designed for General Purpose Applications

CM306 – Open Energy Efficient Rolled Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Most Economical Open Motor Available

CM307 – Open Energy Efficient, Premium Efficient, NEMA Premium . . . . . . . . . . . . . . . . . . . . . . . . . General Purpose Open motors

HARSH ENVIRONMENT SERIESCM311 – Severe Duty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Designed with features for long life in severe environments such as chemical plants, petroleum refineries, and paper mills

CM312 – IEEE 841 XL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exceeds IEEE841 mechanical requirements Built extra tough for durability in harsh environments

CM313 – Aggregate Duty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Designed with high starting torque and break down torque for heavily loaded conveyor and crusher applications

CM315 – Wash Down Duty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Designed for service in wash down applications subject to sanitary codes, IP55

CM318 – Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Designed for use in food or chemical applications where painted motors are undesirable, IP55


Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

128

132

136

146

149

153

163

168

171

176


General Information

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

For additional product information refer to Proposal Builder.

General Information

Efficiency Abbreviations

Agency Approvals/Certifications/DefinitionsNEMA PREMIUM/CEEThe Consortium for Energy Efficiency (CEE) a non-profit, public-benefit corporation helps find ways that consumers, businesses and manufacturers can save energy. CEE members include electric and gas utilities, public interest groups, research and development organizations, state energy offices and regional programs. Both the U.S. Environmental Protection Agency (EPA) and the Department of Energy (DOE) are major partners.

CEE coordinates market research, facilitates the exchange of information and provides interface with national manufacturers, such as Rockwell Automation by establishing specifications for energy-efficient products and services. The tables below can be used to determine which Allen-Bradley motors meet or exceed the NEMA Premium/CEE specifications.

CSACanadian Standards Association is the clearinghouse and coordinating body for standards activity on a national level. Products covered by CSA are either “Certified” or “Labeled” depending on the standards involved.

CSA NRTL/C MARKHazardous Location Report: LR 6771, LR 19467, LR 46877, LR 53258, LR60344

Ordinary Location Report: LR 7861, LR 40567, LR52580, LR 62409

This monogram indicates the product complies with both USA (UL) and CSA standards. This marking should be accepted by all localities in the USA and Canada.

Division II atmosphere is normally not explosive, but under unusual conditions can become explosive. Rockwell Automation has a defined Division II product line and received CSA certification on the following:

180T - 449T AC1080T - 9600 AC169AT - 1610AT DC7MG - 80MG

The standard Division II enclosure is TEFC with Severe Duty features. However, other enclosures are available.

SE=Standard EfficientEE=Energy Efficient (EPAct compliant where applicable)PE=Premium EfficientNP=NEMA Premium Efficient

NEMA Premium/CEE Efficiency Table

NEMA Premium/CEE Efficiency Table

HP RPM Efficiency HP RPM Efficiency

33600 86.5

403600 92.4

1800 89.5 1800 94.11200 89.5 1200 94.1

53600 88.5

503600 93.0

1800 89.5 1800 94.51200 89.5 1200 94.1

7.53600 90.2

603600 93.6

1800 91.7 1800 95.01200 91.0 1200 94.5

103600 90.2

753600 93.6

1800 91.7 1800 95.41200 91.0 1200 94.5

153600 91.0

1003600 94.1

1800 92.4 1800 95.41200 91.7 1200 95.0

203600 91.0

1253600 95.0

1800 93.0 1800 95.41200 91.7 1200 95.0

253600 91.7

1503600 95.0

1800 93.6 1800 95.81200 93.0 1200 95.8

303600 91.7

2003600 95.4

1800 93.6 1800 96.21200 93.0 1200 95.8

General Information - Allen Bradley Control Matched Motors

1

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


C390C390 is the Canadian efficiency equivalent of EPAct. File number: EEV79350

Requires at least an Energy Efficient electrical design motor to meet C390.

CENELECThe European Committee for Electrotechnical Standardization defines compliance standards for CE mark required on motors shipping to Europe.

This mark signifies the motor complies with all applicable European Directives.

REL-4496-001 (Kings Mountain DC Motors)

REL-0296-001 (AC Induction Motors)

REL-4596-001 (Gainesville DC Motors)

For hazardous locations in Europe or for ATEX certification or “EX” mark or flame proof enclosure, contact your local Rockwell Automation sales representative.

Compliance Certification(CC049A and CC019A) NumbersThis symbol and certification numbers indicate that certain Allen-Bradley catalog numbers meet or exceed the energy efficiency requirements contained in title 10 of the Code of Federal Regulations Part 431 (10 CFR Part 431), Energy Conservation Program for Certain Commercial and Indus-trial Equipment and Part C of the Energy Policy and Conservation Act, 42 U.S.C. 6311 et seq. Allen-Bradley motors covered by the certification (Energy Efficient "EE", Premium Efficient "PE", and NEMA Premium “NP”) are footnoted in the catalog with CC049A and CC019A com-pliance certification numbers.

Basic guidelines:• 1-200 hp (.75-150 kw)• Open, Enclosed, or Explosion Proof• 2, 4, or 6 pole (single speed)• Continuous duty• Squirrel cage rotor (NEMA) or cage rotor (IEC)• Foot mounted, including foot mounted with flanges or

detachable feet• NEMA T frame or IEC metric equivalent• NEMA Design A or B, IEC Design N• 60 hz• 230 or 460 volt or both

These are general guidelines and not intended to be used as the final determination of compliance. For specific questions pertaining to this compliance, please contact your Rockwell Automation sales representative.

IEEEInstitute of Electrical and Electronic Engineers is a Technical Organization that publishes various recommended practices, which have been adopted as Industry Standards. Recommended practices do not require approval action or special testing.

Rockwell Automation may furnish specialized equipment in accordance with this specification.

ISO 9000 CertificationRockwell Automation’s continued commitment to quality and worldwide acceptance is evidenced by the Madison, IN, Athens, GA, Gainesville, GA, Kings Mountain, NC and Stratford, Ontario motor plants’ certification to the ISO 9001 international quality standard. Many of Rockwell Automation’s other locations are also ISO 9000 certified. Please contact your local Rockwell Automation representative for additional information on the ISO 9000 standards and Rockwell Automation compliance.

NECNational Electrical Code is an ASA Standard “NFPA-70” sponsored by the National Fire Protection Association for the purpose of safeguarding persons and buildings from electrical hazard arising from the use of electricity for light, heat, power, and other purposes.

NEMANational Electrical Manufacturers Association. Standards are voluntary standards that represent general practices in the industry. They define a product, process or procedure with reference to nomenclature, composition, construction, dimensions, tolerances, operating characteristics, performance, quality, rating and testing. Specifically, they cover such matters as frame sizes, torque classifications, and basis of rating.

NRCAN Natural Resources CanadaFor Canadian customers, NRCAN regulations require registration and energy efficiency reporting of certain 1-200HP and 0.75-150KW rated motors. The following website address will lead to the NRCAN website and Rockwell Automation forms for both NEMA and IEC motors as well as UMI codes. The address is www.reliance.com/mtr/orgreg.htm. Just click on NRCAN from the column on the left side of this website page.


2

General

Information

CM

100C

M 200

CM

300F

ootnotes


UL & URUnderwriters’ Laboratories, Inc. is chartered as a non-profit organization to establish, maintain, and operate laboratories for the examination and testing of devices, systems, and materials. The UL presently publishes more than 250 Standards for Safety for materials, devices, constructions and methods. UL also undertakes numerous research projects in areas of

safety.

/Description

Description

Division I atmosphere is considered potentially explosive under normal conditions.


Temperature Codes (“T” Codes)NEC requires explosion-proof motors to indicate the maximum operating surface temperature. A “T” Code is used as the temperature identification value and it is taken from the National Electric Code. The “T” Code is based on the minimum ignition temperature of the substances to be found in the hazardous location. (Ignition temperature is when substance will start to burn or explode) The code, when marked on a motor nameplate, represents the highest temperature that could be obtained on the motor surface under any normal or abnormal operating conditions including locked rotor, single phasing or overloading, and is chosen to be below the ignition temperature of the substance in the hazardous area. The “T” Code designations apply to motors and other types of electrical equipment subject to hazardous location classification. For further information, consult the Motor Technical Reference (MTR) on the Web at http://www.reliance.com/mtr.

Cancellation ChargesNon-Stock MotorsA minimum charge of $100 will apply to any order cancellation. Cancellation charges for orders received and entered on the manufacturing facility will be determined based on cost incurred.

Completion of order includes consideration of the following:

• order edit and acknowledgment• capacity allocation• engineering and specification• material commitment (raw, finished, and purchased)

Completion progress to be determined by producing plant customer service.

Stock MotorsNo cancellation charges are incurred if order is cancelled prior to shipment.

Freight PolicyFor complete information, refer to appropriate discount sheet.

Frames/Description Environment File Number

48 - 140T Hazardous E6881182T - 9500 AC Hazardous E10822

180AT - 500AT DC Hazardous E10822Thermal Protectors Recognized E22031Motor Components Recognized E54825Insulation Materials Recognized E39972

Conduit Boxes Hazardous E30225, E40711Hermetic Recognized SA5484


3

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Limited Warranty PolicyAll Allen-Bradley Brand Products are warranted against defects in workmanship and materials. Most are covered for 12 months from date of installation or 18 months from date of manufacture, whichever occurs first. Some products carry a longer warranty period.

If within the warranty period, Rockwell Automation receives from the Buyer written notice of any alleged defects in any such Product and if the apparatus is not found to be in conformity with this warranty (the Buyer having provided Rockwell Automation a reasonable oppor-tunity to perform any appropriate tests thereon) Rockwell Automation will, at its option, either repair the same or supply a replacement therefor.

Rockwell Automation under either option shall have the right to require the Buyer to deliver the apparatus for this purpose to its designated service center or manufacturing facility and the Buyer shall pay all charges for in-bound and out-bound transportation and for services of any kind, diagnostic or otherwise, excepting only direct and actual costs of apparatus repair or replacement as provided above. Rockwell Automation is not responsible for inciden-tal or consequential charges to include, but not limited to, removal, installation, downtime, etc.

This limited warranty does not apply to normal wear items or any product which has been subject to misuse, misap-plication, neglect (including without limitation, inadequate maintenance or failure on the part of the Buyer to ensure

proper storage), accident or improper installation, modifi-cation, adjustment, or repair. This constitutes Rockwell Automation's only warranty in connection with this sale.

THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESSED, IMPLIED OR STATUTORY, INCLUDING IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE, OR PERFORMANCE OR APPLICATION WARRANTIES, AND EXTEND ONLY TO CUSTOMERS PURCHASING FROM SELLER OR ITS APPOINTED DISTRIBUTOR.

No employee, agent, dealer or other person is authorized to give any warranties on behalf of Rockwell Automation nor to assume for Rockwell Automation any other liability in connection with any of its Products, unless otherwise agreed in writing by Rockwell Automation's Headquarters.

Warranty Administration and ProcessingWarranty claims can be processed using the Motor Warranty Administration form available on the Control-Matched web-site at www.controlmatched.comSelect the radial button for “Warranty Request Form”. All required fields MUST be filled in for a warranty request to be processed.

*Whichever warranty period occurs first

Product Type

Warranty Period*

From Installation Date From Date of Manufacture

Standard efficient motors (SE) 12 months 24 months

Energy Efficient motors (EE) 12 months 24 months

Premium Efficient motors (PE) 24 months 36 months

NEMA Premium Efficient motors (NP) 24 months 36 months

IEEE-841 motors 48 months 60 months

DC Motors – CM205, CM206 12 months 24 months

Vector Duty AC motors – CM201, CM202, CM203 24 months 36 months


4

General

Information

CM

100C

M 200

CM

300F

ootnotes


Motor Selection and Application

SafetyThe use of electric motors, like that of all other utilization of concentrated power, is potentially hazardous. The degree of hazard can be greatly reduced by proper design, selection, installation and use, but hazards cannot be completely eliminated.

Some of the factors that must be considered for the safe application of motors are as follows:

1. Enclosure2. Service conditions3. Proper matching of the motor to the load4. Proper sizing and connection to an inverter by qualified

technicians

Information on these factors is presented in this section.

EnclosureThe selection of the proper enclosure is vital to the successful safe operation of AC motors. Machine performance and life can be materially reduced by using an enclosure inappropriate for the application. The customer must recognize the specific environmental conditions and specify the correct enclosure. Rockwell Automation can provide application assistance, but must depend on the customer to provide accurate information on the operating conditions.

Rockwell Automation offers motors in the following enclosures:

• Open Drip-Proof• Totally Enclosed (Non-Ventilated, Fan Cooled, Air Over)• Explosion Proof• Dust Ignition Proof

Open Drip-Proof Motor (ODP)An ODP motor is an open machine having all openings limited in size to prevent accidental contact with hazardous parts. Internal parts are protected from drip, splash and falling objects on all horizontal and vertical mounted motors. ODP motors are suitable for general industrial use in indoor locations with relatively clean atmospheres.

Totally Enclosed MotorA totally enclosed motor is one so enclosed as to prevent the free exchange of air between the inside and the outside of the case but not sufficiently enclosed to be termed air-tight. Totally enclosed motors are suitable for use in dusty dirty locations and in humid environments.

Totally Enclosed Non-Ventilated - Not equipped for cooling by means external to the enclosing parts. Generally limited to low horsepower ratings or short-time rated motors.

Totally Enclosed Fan-Cooled - Exterior surface cooled by external fan on motor shaft. Motor cooling is dependent on motor speed.

Totally Enclosed Air-Over - Exterior surface cooled by a ventilating means external to the motor. Customer must provide sufficient air flow to cool motor.

Additional protection for motors used in extremely dirty or humid conditions is offered by Rockwell Automation Severe Duty features.

(IP) Classification of EnclosuresThe classification system consists of the letters IP (Ingress protection) followed by two numbers. The first number indicates the degree of protection against entry of solid material into the enclosure. The second number indicates the degree of protection against entry of liquids.

Table 1: Degree of protection against solid material and personal injury indicated by the 1st numberNumberal Definition

0No special protection of persons against accidental or inadvertent contact with live or moving parts or against the ingress of solid material

1Protection against accidental inadvertent contact with live or moving parts by large surface of a body such as a hand or similar object exceeding 50 mm

2Protection against accidental or inadvertent contact with live or moving parts by a finger or similar object exceeding 12 mm

3Entry prevented of tools, wires or other solid objects of a diameter or thickness greater than 2.5 mm

4Entry prevented of wires, strips or solid objects of a diameter or thickness greater than 1.0 mm

5

Complete protection against contact with live or moving parts inside the enclosure. The entry of dust is not totally prevented, but dust cannot enter in sufficient quantity to interfere with the satisfactory operation of the motor

6No ingress of dust. Per IEC 34-5 this degree of protection is not applicable to rotating equipment such as motors and generators but applicable to electrical enclosures


5

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


(IP) Classification of Enclosures (con’t)

Abbreviations for Enclosure TypesDPG - Drip-Proof Guarded

DPG-FV - Drip-Proof Guarded - Force Vent

DPSV - Drip-Proof, Separately Vented

FC - Fan Cooled

FCXP - Fan Cooled, Explosion Proof

IP-22 - Open Drip-Proof (IEC Standard)

IP-23 - Splash Proof (IEC Standard)

IP-44 - Totally Enclosed (IEC Standard)

IP-54 - Splash Proof (IEC Standard)

IP-55 - Washdown (IEC Standard)

NV - Non-Ventilated

NVXP - Non-Ventilated, Explosion Proof

ODP - Open Drip-Proof

SPG - Splash Proof Guarded

TEAO - Totally Enclosed, Air Over

TEBC - Totally Enclosed, Blower Cooled

TEDC-AA - Totally Enclosed, Dual Cooled, Air to Air

TEDC-AW - Totally Enclosed, Dual Cooled, Air to Water

TEFC - Totally Enclosed, Fan Cooled

TENV - Totally Enclosed, Non-Ventilated

WPI - Weather Protected, Type I

WPII - Weather Protected, Type II

Explosion Proof and Dust Ignition ProofMotors For Hazardous LocationsExplosion Proof - An Explosion Proof motor is a totally enclosed machine designed to operate safely in an environment in which flammable gas or vapor is present. This is accomplished by limiting the external surface temperature of the motor below the ignition temperature of the hazardous gas or vapor surrounding the motor. Hence it is very important that the end user order a motor with the proper temperature code. Also the enclosure is designed to contain an explosion on the inside of the motor which may be caused by arcing, sparking, or abnormal heat. A flame caused by such an explosion will not propagate the motor fits and ignite the gas or vapor surrounding the motor. An explosion proof motor is suitable for operation in Class I hazardous environment.Dust Ignition Proof - A Dust Ignition Proof motor is a totally enclosed machine designed to operate safely in a flammable dust environment. The motor enclosure pre-vents the admittance of dust inside the motor. Also the motor is designed to operate cool enough so as not to ignite any dust which might accumulate on the external surface of the motor. Should the motor become blanketed with dust and reduce its normal cooling, winding thermostats will take the motor off line before the motor’s external surface temperature reaches the ignition temper-ature of the hazardous dust. A dust-ignition-proof motor is suitable for operation in a Class II hazardous location.The specific dust or gas present in the hazardous location is identified by the group listing for each Class. Certain Allen-Bradley AC motors are listed for use in Class I Groups C and D and Class II Groups E, F and G locations depending on the horsepower rating, frame size and enclosure as indicated on the price pages. The user customer is responsible for insuring that the proper UL listed motor is used in a specific hazardous location.


Table 2: Degree of protection of motors against the harmful ingress of water by the 2nd numberNumberal Definition

0 No special protection

1 Vertically falling drops

2 Drops falling at any angle up to 15° off of vertical

3 Spray at any angle up to 60° off of vertical

4 Splashed from any direction

5Projected by nozzle from any direction has no harmful effect

6Water from heavy seas or projected from powerful water jets has no harmful effect

7Entry of water in a harmful quantity is prevented when the unit is immersed in water under stated conditions of pressure and time

8Immersed under water specified pressure for an indefinite time

ATTENTION: Misapplication of a motor in a hazardous environment can cause a fire or an explosion and result in serious injury. Only the end user and/or insurance underwriter are qualified to identify the appropriate class(es), group(s), division and temperature code. Rockwell Automation personnel should not render any assistance in identifying the type of environment.

!


6

General

Information

CM

100C

M 200

CM

300F

ootnotes


Service ConditionsStandard motors listed in this catalog are designed to operate under the following service conditions. Service conditions exceeding these conditions may require special motor selection or re-rating of standard motors.Altitude - Sea Level to 3300 feet.Ambient Temperature - -25° C to 40° C.Mounting - The standard motors listed in this catalog are either foot mounted or have a C-face as indicated on the price pages. The motor must be mounted on a rigid mounting surface for satisfactory operation.Installation - Motor must be in areas or in supplementary enclosures which do not seriously interfere with the ventilation of the motor.

Power SupplyPhase - Motors are designed for either single-phase or three-phase operation as indicated on the price pages. Single-phase motors may be operated on one-phase of a three-phase power supply with the rated voltage. Operation of a three-phase motor on a single-phase supply will result in motor damage.

VoltageSingle Phase Motors - standard voltages are 115/230.

Three Phase Motors - standard voltage are 190/380, 200, 200/400, 230/460, 208-230/460, 460 and 575 as indicated on the price pages. Specific Definite Purpose motors may have other voltages indicated. Motors rated at 230 or 230/460 volts will operate on a 208 volt supply except that starting and peak running torques at 208 volts will be 20-25% less than at the 230 volt rating. Motors nameplated 208-230/460 will operate satisfactorily at 208volts.

Voltage Variation - In accordance with NEMA standards, Allen-Bradley motors will operate with +10% variation in rated voltage with rated frequency. Performance within this voltage variation will not necessarily be in accordance with performance at rated voltage.

Dual Voltage Motors are easily reconnectable by referring to the information on the motor nameplate.

Frequency - Motors are designed for operation on 50 or 60 Hz as specified on the price pages. Many motors designed for operation on 60 Hz power may be operated on 50 Hz power of a lower voltage rating with resulting decrease in speed and horsepower. Refer to Rockwell Automation for details. In accordance with NEMA standards Allen-Bradley motors will operate with +5%variation in rated frequency with rated voltage. Performance with this frequency variation will not necessarily be in accordance with performance at rated frequency.

Insulation Class & Temperature RiseMotor Insulation systems are classified by the maximum total temperature at which the system can be operated without adversely affecting design life. This maximum total temperature has three components.

Four classes of insulation systems are used in motors. In general, the temperature values are as follows:

Proper Matching of the Motors to the LoadGeneral information on the torque/speed characteristics of the various NEMA design classes is given under “TORQUE/NEMA DESIGN CLASSES” on the following page.

The equipment manufacturer and/or user is responsible for selecting the correct motor rating to drive the load.

Ambient Temperature = The temperature of the atmosphere in which the motor is operated. 40° C is considered a standard for design purposes.

Temperature Rise = The number of degrees which the insulated motor windings heat up during motor operation

Hot Spot Allowance= The value that takes into account the additional temperature variations within the inaccessible spots of a motor winding. These spots are located in the stator slots or coil heads. 10° C is considered a standard for design purposes.

InsulationClass

Max Total Temperature

@ 1.0 sf

Components of Max Total Temp.

AmbientTemperature

RiseHot Spot

Allowance

A 105° C = 40° C 55° C 10° C

B 130° C = 40° C 80° C 10° C

F 155° C = 40° C 105° C 10° C

H 180° C = 40° C 130° C 10° C


7

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Torque/NEMA Design ClassesThe full load torque of a motor is expressed as follows:

Since different loads present different torque requirements at starting (breakaway), minimum (pull-up), breakdown (pull-out) and full load, the National Electrical Manufacturers Association (NEMA) has defined four standard design classes A,B,C and D of squirrel cage polyphase induction motors. These design classes are summarized in Table I.

The general torque/speed relationship with the four torque points defined is shown in Figure 1. The NEMA design class is indicated on each price page in this catalog. Most motors are Design B with a few Design A, C & D. For motors having different characteristics than listed, contact Rockwell Automation.

Speed/SlipThe synchronous speed of an AC motor is as follows:

The number of poles is a function of motor design. Standard 60 Hz motors are available with synchronous speeds of 3600, 1800, 1200 or 900 rpm.

The actual operating speed of an AC induction motor is determined by the synchronous speed and the slip. Slip is the difference between the speed of the rotating magnetic field (which is always synchronous) and the rotor speed. Slip generally increases with an increase in motor torque; therefore, actual operating speed generally decreases with an increase in the driven load torque.

Service FactorThe service factor of a motor is a multiplier which, when applied to the rated horsepower, indicates a permissible horsepower loading which may be carried under the conditions specified for the service factor.

Table I. Characteristics of NEMA design classes for squirrel-cage polyphase induction motors

NEMADesign

StartingTorque

StartingCurrent

Breakdown Torque

Full Load Slip Typical Applications

A Normal High High Low Mach. Tools, FansB Normal Normal Normal Normal General Industrial

C High Normal Normal NormalLoadedCompressor,Loaded Conveyor

D Very High Low - High Punch Press or Hoists

Full load torque (ft. lbs) =HP x 5250

Full load speed (rpm)

Figure 1 - General Speed/Torque relationship for squirrel-cage polyphase induction motors.

Motor torque is defined at four points as shown.

1. Breakaway or starting2. Minimum or “pull-up”3. Breakdown or “pull-out”4. Full load

Synchronous Speed(rpm)

120 x Power Supply Frequency (HZ)Number of Poles

=


8

General

Information

CM

100C

M 200

CM

300F

ootnotes


9

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Evaluating Motor Efficiency

Analyze, Compare and Calculate Your Energy SavingsThe graphs below show how the Allen-Bradley PE motor efficiency and watts loss curves compare to standard industrial averages. The table below shows the results of these comparisons in terms of annual energy savings.

MotorEfficiency

Motor WattsLoss4-pole, 1800 RPMTEFC Designs

AnnualSavingsBased on $.08 per kilowatt hour, 7200 hours of full load operation per year. Allen-Bradley PE TEFC motors and Industry Averages - 4-pole, 1800 RPM Designs.

As you can see, a 150 HP PE motor could save you $2,831 a year in power costs over standard 150 HP designs, based on electrical costs of $.08 per kilowatt hour and 7200 hours of full load operation per year. The table also shows comparable savings for other motors in the PE motor line. Your actual savings may vary, depending on the electrical rates, load conditions and annual operating hours of your application.

In the long term, the decision to invest in an energy efficient Allen-Bradley PE motor depends on the energy savings it can provide. Actual energy savings depend upon many variables including operating hours, cost of power, duty cycles, and line voltages to name a few. Tax rates and the future cost of money will also influence the decision.

However, a very simple energy savings calculation can be made to estimate the yearly energy savings with a PE motor.

Simple Energy Savings CalculationThis simple payback analysis will assume constant full load operation. Note that this calculation ignores the effects of taxes and the time value of money. Later, we’ll take partial load and variable duty cycles into account.

Information you need to know.

If actual motor efficiency is unknown, a Rockwell Automation sales engineer can help you estimate standard motor efficiencies.

First, calculate the kilowatts saved by using the PE motor:

Kilowatts Saved = HP x.746

Then, calculate the yearly energy savings:

Yearly Savings = Kilowatts Saved x Hrs/Yr x $/KWH

HP PE NOMINAL EFF. IND. AVE. EFF. WATTS SAVED MONEY SAVED

1 86.5 76.5 113 $651 1/2 87.5 78.5 147 84

2 87.5 80.8 141 813 89.5 79.9 300 1735 90.2 83.1 353 204

7 1/2 91.7 83.8 575 33110 91.7 85.0 641 36915 92.4 86.5 826 47620 93.0 87.5 1008 58125 93.6 88.0 1268 73030 93.6 88.1 1493 86040 94.1 89.4 1667 96050 94.5 90.4 1790 1,03160 95.0 90.3 2452 1,41375 95.4 90.8 2971 1,711

100 95.4 91.6 3244 1,869125 95.8 91.8 4241 2,443150 96.2 92.3 4915 2,831200 96.2 93.3 4821 2,777250 96.2 93.6 5385 3,102300 96.5 93.8 6676 3,845

HP = Motor full load horsepowerHrs/Yr = Number of hours per year the motor

is in operation$/KWH = Cost of electricity in dollars per

kilowatt hourPEEFF = PE motor efficiencySTDEFF = Standard motor efficiency

[ ]1STDEFF

1PEEFF


10

General

Information

CM

100C

M 200

CM

300F

ootnotes


Example

Assume that a 25 horsepower motor is going to operate for three 8-hour shifts per day, on a 6-day work week, for 50 weeks per year. Thus, total hours per year are 7200. Also, assume the cost of electricity at $.08 per kilowatt hour. The savings, using the PE motor with an efficiency of 93%, compared to the 88% which is the industry average for a standard efficient motor, is calculated as follows:

Yearly Savings = Kilowatts Saved x Hrs/Yr x $/KWH

In this case, the yearly savings is $656.36. In other words, if you wanted a one-year payback on your investment, you could afford to spend $656 more for the PE energy efficient motor than for a standard efficient motor.

Duty CyclesMany people question the energy savings of partial load or variable duty cycle applications. The energy saving equations are the same. However, when evaluating a partial load operation, remember to use the horsepower, efficiency, and appropriate hours of operation at the desired load point. A variable duty cycle calculation is simply the summation of several partial load calculations.

Additional SavingsThis payback analysis also does not take into account many additional savings you should consider.

• Longer motor life as a result of cooler operating temperatures

• Additional cost savings from improved power factor• Improved partial load efficiencies of the PE motor• Improved reliability with a more forgiving electrical

design• Quieter operation• Greater flexibility for use on adjustable frequency power

supplies

This is why so many companies specify Allen-Bradley PE energy efficient motors for all their applications.

Useful FormulasElectrical

I = Amperes: E = Volts; Eff = Efficiency; pf = Power factor; Kva = Kilovolt-amperes; Kw = Kilowatts

HP/Torque/SpeedFor Rotary Objects

For Objects In Linear Motion

Speed

Inertia Loads

Temperature Conversion - Centigrade / Fahrenheit

Temp. F = (9/5 Temp. C) +32Temp. C = 5/9 (Temp. F – 32)

Kilowatts Saved = HP x.746 1 1STD EFF PE EFF

-

= 25 x.746 1 1.880 .930

-

= 1.139 Kilowatts Saved

= 1.139 x 7200 x.08

= $656.36

To FindAlternating Current

Single Phase Three Phase

Amperes when horsepower is known

HP x 746E x Eff x pf

HP x 7461.73 x E x Eff x pf

Amperes when kilowatts are known

Kw x 1000E x pf

Kw x 10001.73 x E x pf

Amperes when kva areknown

Kva x 1000E

Kva x 10001.73 x E

Kilowatts I x E x pf1000

1.73 x I x E x pf1000

Kva I x E1000

1.73 x I x E1000

Horsepower =(Output)

I x E x Eff x pf746

1.73 x I x E x Eff x pf746

°C °F °C °F °C °F

-30 -22 50 122 95 203-20 -4 55 131 100 212-10 14 60 140 110 2300 32 70 158 115 239

10 50 75 167 130 26620 68 80 176 150 30230 86 85 185 180 35640 104 90 194 200 392

HP x 5250 Torque x rpmTorque in Lb.-ft = HP = rpm 5250

FV Where F = Force (lbs.) HP = 33,000 V = Velocity (FPM)

RPM = 120 Frequency

No. of Poles

t = WK2 = Inertia in lb. ft 2WK2 x rpm

308 x T t = accelerating time in sec. T = Avg. accelerating torque lb. ftt =

308 x TWK2 x rpm

Inertia reflected to motor = Load inertiaMotor rpmLoad rpm 2( (


11

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Rush/Breakdown OrdersStock motors can be shipped same day or next day. Same day ship orders MUST be entered prior to 10:00 AM (central time zone) and require customers to approve next day freight charges. All rush orders are subject to stock availability.

Sales Order Change ChargesA minimum change order charge of $100 net will apply to orders changed more than 24 hours after order entry. All sales order changes, regardless of their nature, must be processed through the initiation of a Sales Order Change Request on the Passport system. This includes ship-to address changes, carrier or shipping class changes, etc.

Rockwell Automation Motor Service CentersThe following list includes all Rockwell Automation Service Centers within the continental United States. Many inde-pendent approved service shops do exist. Contact your local Allen-Bradley distributor or sales office if one of these service shops is not in your area.

Birmingham Regional Service Center3100 Pinson Valley ParkwayBirmingham, AL 35217Phone: 205.841.8377FAX: 205.841.8035

Carolina Regional Service Center1332 Firetower RoadRock Hill, SC 29731Phone: 803.324.3700FAX: 803.324.0434

Chicago Regional Service Center17001 South Vincennes RoadThorton, IL 60476Phone: 708.877.5310FAX: 708.877.6516

Ohio Valley Regional Service Center2175-A Schlicter DriveHamilton, OH 45015Phone 513.863.8816FAX: 513.863.7679

Denver Regional Service Center1020 South Lipan StreetDenver, CO 80223Phone: 303.935.4615FAX: 303.935.0129

Houston Regional Service Center1500 East Main StreetLaPorte, TX 77571Phone: 281.471.4611FAX: 281.471.3120

Philadelphia Regional Service Center3240 South 78th StreetPhiladelphia, PA 19153Phone: 215.365.1500FAX: 215.365.1530

Portland Regional Service Center2315 N.W. 21st PlacePortland, OR 97210Phone: 503.226.4951FAX: 503.226.7340

Rock Springs Regional Service Center839 Elk StreetRock Springs, WY 82901Phone: 307.362.6697FAX: 307.382.2618

Shreveport Regional Service Center1245 North Hearne AvenueShreveport, LA 71107Phone: 318.222.9431 or (24 Hour Emergency Service - 800.366.6030)FAX: 318.424.1702

Washington Regional Service Center320 Reliance DriveWashington, PA 15301-6196Phone: 724.225.2900 FAX: 724.225.4309

Parts AdministrationReplacement and spare parts are available for all motors offered in this catalog. Spare parts not included in this catalog are available through Rockwell Automation Global Technical Support (GTS). To access parts information, record the catalog number and motor ID (identification) number from the motor nameplate and call the GTS Parts Hub.


12

General

Information

CM

100C

M 200

CM

300F

ootnotes


DocumentationThe following table indicates motor documentation and reports that can be ordered with your Allen-Bradley motor. These catalog numbers must be ordered at the same time the motors are ordered.

Return RequestsStock Motors and accessories are able to be returned for credit in many cases. In cases where a return has been authorized, the minimum re-stock charges will be 25% of the original net price. Equipment must be in original pack-aging, un-used, have been stored per storage require-ments identified in publication MOTOR-5.0, be a product currently maintained in stock inventory, and must be no more than 90 days old (reference original date of ship-ment). Modified and build to order motors are not able to be returned for credit. Return freight charges are the responsibility of the party returning the equipment for credit.

RAISE Software - ElectronicProduct Information

Technical Information for specific motors is available prior to order entry through use of Proposal Builder. Preliminary dimension sheets, performance data, and connection diagrams are available for many motors in Proposal Builder. Contact your local Allen-Bradley Distrib-utor or Sales Office to get a copy of this Allen-Bradley product information selection and information tool.

Catalog Number Description List Price Discount Schedule Typical Lead Time

1301-MTRCERT MOTOR CERTIFIED DRAWINGS $50 16 4-6 weeks

1301-MTRMFG TYPICAL DIMENSION DRAWING $0 16 Varies

1301-MTRACAD MOTOR DIMENSION DRAWINGS in AUTOCAD 14 FORMAT on DISK

$150 16 After Motor Ships

1301-MTRAPP MOTOR APPROVAL DRAWINGS $0 16 4-6 weeks

1301-MTRSTDPD MOTOR STD TABULATED PERFORMANCE DATA $60 16 After Motor Ships

1301-MTRPLIST MOTOR SPARE PARTS LIST $15 16 After Motor Ships


13

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


CM100 Family

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Component Class, Inverter Duty General Purpose SeriesCM101 - Enclosed EE Rolled Steel AC Motors

Foot Mounted IP54Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Catalog String Notes US List

RPM Class Torque/Spd Stock CM101- PriceTEFC 1.5 1200 230/460 EE CT 10:1 Yes 182T FC1F512AEHHA 9 $578TEFC 2 1200 230/460 EE CT 10:1 Yes 184T FC00212AEHHA 9 $630TEFC 3600 230/460 EE CT 10:1 Yes 182T FC00336AEHHA 9 $575TEFC 1800 230/460 EE CT 10:1 Yes 182T FC00318AEHHA 9 $507TEFC 1200 230/460 EE CT 10:1 Yes 213T FC00312AEHHA 9 $702TEFC 3600 230/460 EE CT 10:1 Yes 184T FC00536AEHHA 9 $658TEFC 1800 230/460 EE CT 10:1 Yes 184T FC00518AEHHA 9 $571TEFC 1200 230/460 EE CT 10:1 Yes 215T FC00512AEHHA 9 $955TEFC 3600 230/460 EE CT 10:1 Yes 213T FC7F536AEHHA 9 $782TEFC 1800 230/460 EE CT 10:1 Yes 213T FC7F518AEHHA 9 $688TEFC 1200 230/460 EE CT 4:1 Yes 254T FC7F512AEKHA 9 $1,197TEFC 3600 230/460 EE CT 10:1 Yes 215T FC01036AEHHA 9 $901TEFC 1800 230/460 EE CT 10:1 Yes 215T FC01018AEHHA 9 $755TEFC 1200 230/460 EE CT 4:1 Yes 256T FC01012AEKHA 9 $1,454TEFC 3600 230/460 EE CT 4:1 Yes 254T FC01536AEKHA 9 $1,159TEFC 1800 230/460 EE CT 4:1 Yes 254T FC01518AEKHA 9 $1,062TEFC 1200 230/460 EE CT 2:1 Yes 284T FC01512AEJHA 9 $1,741TEFC 3600 230/460 EE CT 4:1 Yes 256T FC02036AEKHA 9 $1,383TEFC 1800 230/460 EE CT 4:1 Yes 256T FC02018AEKHA 9 $1,256TEFC 1200 230/460 EE CT 2:1 Yes 286T FC02012AEJHA 9 $2,115TEFC 3600 230/460 EE CT 2:1 Yes 284TS FC02536AEJHA 9,39 $1,561TEFC 1800 230/460 EE CT 2:1 Yes 284T FC02518AEJHA 9 $1,498TEFC 3600 230/460 EE CT 2:1 Yes 286TS FC03036AEJHA 9,39 $1,826TEFC 1800 230/460 EE CT 2:1 Yes 286T FC03018AEJHA 9 $1,741

Discount Schedule 16 ee CC049A

C-Face Foot Mounted IP54Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Catalog String Notes US List

RPM Class Torque/Spd Stock CM101- PriceTEFC 1.5 1200 230/460 EE CT 10:1 Yes 182TCY FC1F512AEHCA 9 $647TEFC 2 1200 230/460 EE CT 10:1 Yes 184TCY FC00212AEHCA 9 $699TEFC 3600 230/460 EE CT 10:1 Yes 182TCY FC00336AEHCA 9 $643TEFC 1800 230/460 EE CT 10:1 Yes 182TCY FC00318AEHCA 9 $576TEFC 1200 230/460 EE CT 10:1 Yes 213TCY FC00312AEHCA 9 $770TEFC 3600 230/460 EE CT 10:1 Yes 184TCY FC00536AEHCA 9 $726TEFC 1800 230/460 EE CT 10:1 Yes 184TCY FC00518AEHCA 9 $639TEFC 1200 230/460 EE CT 10:1 Yes 215TCY FC00512AEHCA 9 $1,023TEFC 3600 230/460 EE CT 10:1 Yes 213TCY FC7F536AEHCA 9 $851TEFC 1800 230/460 EE CT 10:1 Yes 213TCY FC7F518AEHCA 9 $757TEFC 1200 230/460 EE CT 4:1 Yes 254TCY FC7F512AEKCA 9 $1,287TEFC 3600 230/460 EE CT 10:1 Yes 215TCY FC01036AEHCA 9 $969TEFC 1800 230/460 EE CT 10:1 Yes 215TCY FC01018AEHCA 9 $823TEFC 1200 230/460 EE CT 4:1 Yes 256TCY FC01012AEKCA 9 $1,543TEFC 3600 230/460 EE CT 4:1 Yes 254TCY FC01536AEKCA 9 $1,249TEFC 1800 230/460 EE CT 4:1 Yes 254TCY FC01518AEKCA 9 $1,151TEFC 1200 230/460 EE CT 2:1 Yes 284TC FC01512AEJCA 9 $1,865TEFC 3600 230/460 EE CT 4:1 Yes 256TCY FC02036AEKCA 9 $1,473TEFC 1800 230/460 EE CT 4:1 Yes 256TCY FC02018AEKCA 9 $1,345TEFC 1200 230/460 EE CT 2:1 Yes 286TC FC02012AEJCA 9 $2,239TEFC 3600 230/460 EE CT 2:1 Yes 284TSC FC02536AEJCA 9,39 $1,685TEFC 1800 230/460 EE CT 2:1 Yes 284TC FC02518AEJCA 9 $1,622TEFC 3600 230/460 EE CT 2:1 Yes 286TSC FC03036AEJCA 9,39 $1,950TEFC 1800 230/460 EE CT 2:1 Yes 286TC FC03018AEJCA 9 $1,865


15

20

25

30

3

5

7.5

10

15

20

25

30

3

5

7.5

10

CM101 Family - Enclosed EE Rolled Steel AC Motors

15

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

C-Face Footless IP54Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Catalog String Notes US List

RPM Class Torque/Spd Stock CM101- PriceTEFC 1.5 1200 230/460 EE CT 10:1 Yes 182TC FC1F512AEHFA 9 $663TEFC 2 1200 230/460 EE CT 10:1 Yes 184TC FC00212AEHFA 9 $715TEFC 3600 230/460 EE CT 10:1 Yes 182TC FC00336AEHFA 9 $659TEFC 1800 230/460 EE CT 10:1 Yes 182TC FC00318AEHFA 9 $592TEFC 1200 230/460 EE CT 10:1 Yes 213TC FC00312AEHFA 9 $787TEFC 3600 230/460 EE CT 10:1 Yes 184TC FC00536AEHFA 9 $742TEFC 1800 230/460 EE CT 10:1 Yes 184TC FC00518AEHFA 9 $655TEFC 1200 230/460 EE CT 10:1 Yes 215TC FC00512AEHFA 9 $1,039TEFC 3600 230/460 EE CT 10:1 Yes 213TC FC7F536AEHFA 9 $867TEFC 1800 230/460 EE CT 10:1 Yes 213TC FC7F518AEHFA 9 $773TEFC 1200 230/460 EE CT 4:1 Yes 254TC FC7F512AEKFA 9 $1,326TEFC 3600 230/460 EE CT 10:1 Yes 215TC FC01036AEHFA 9 $986TEFC 1800 230/460 EE CT 10:1 Yes 215TC FC01018AEHFA 9 $840TEFC 1200 230/460 EE CT 4:1 Yes 256TC FC01012AEKFA 9 $1,582TEFC 3600 230/460 EE CT 4:1 Yes 254TC FC01536AEKFA 9 $1,287TEFC 1800 230/460 EE CT 4:1 Yes 254TC FC01518AEKFA 9 $1,190TEFC 1200 230/460 EE CT 2:1 Yes 284TC FC01512AEJFA 9 $1,923TEFC 3600 230/460 EE CT 4:1 Yes 256TCY FC02036AEKFA 9 $1,511TEFC 1800 230/460 EE CT 4:1 Yes 256TCY FC02018AEKFA 9 $1,384TEFC 1200 230/460 EE CT 2:1 Yes 286TC FC02012AEJFA 9 $2,297TEFC 3600 230/460 EE CT 2:1 Yes 284TSC FC02536AEJFA 9,39 $1,743TEFC 1800 230/460 EE CT 2:1 Yes 284TC FC02518AEJFA 9 $1,680TEFC 3600 230/460 EE CT 2:1 Yes 286TSC FC03036AEJFA 9,39 $2,008TEFC 1800 230/460 EE CT 2:1 Yes 286TC FC03018AEJFA 9 $1,923


15

20

25

30

3

5

7.5

10


16

General

Information

CM

100C

M 200

CM

300F

ootnotes

Modifications Available to CM101 MotorsGeneral InformationChanges to an Order

Once shipped, modified motors cannot be returned.Delivery Cycle

HoursThe Modification Center is operated from 7 am to 3 pm Central Time Monday through Friday.

US ListCode Modification Description Frame Price Notes

CONNECTIONS: Final connect dual to single voltage.107 High Voltage Connection All $162108 Low Voltage Connection All $162

DRIP COVERS: Mounting of stock canopy kits (price includes kit).116 Install canopy kit to allow for vertical shaft down operation. 180-210 $216

Note: This modification does not provide vertical lifting provisions. 250-280 $270LEAD TERMINALS: Addition of lead terminals to wires in conduit box.

135 Compression type (Burndy, etc.) lead lugs All $270MOUNTING: Move conduit box to allow different mounting configurations.

140 F-1 to F-2 180-280 $251 Note: Not available on L180-L210 frames 320-449 $376

141 F-1 to W6 180-280 $251 Note: Not available on L180-L210 frames 320-449 $376



144 F-1 to W7 180-280 $251 Note: Not available on L180-L210 frames 320-449 $376 SPACE HEATERS:

180 Addition of 120V single phase, 60 Hz space heater, aux CB not included 48, 56, 140 $359180-280 $419320-400 $470

440-L449 $589SEALS: Addition of shaft seal.

148 Additon of V-ring rubber slinger on drive end All $216THERMAL PROTECTION: Addition of thermostats.

Standard in Component Class Motors All incl160 Removal of standard thermostats from motor (deduct from List Price) 48-280 -$208

Note: User must insure that NEC 2005 is met for inverter duty motor 320-449 -$313

To cancel an order for a motor after it is modified, but before it ships - a cancellation charge of double the modification charge will be invoiced to the customer. Any MOD order cancelled before modification is completed is subject to 25% cancellation charge.

The delivery cycle will be subject to the availability of stock motors and parts. The Modification Center is designed to process and ship units as quickly as possible; therefore, “Hold for Approval” and other similar conditions are not available on Modification Center orders. Typically, modifications will require 1 to 4 business days, once the order is entered. Orders for more than 5 units may require additional delivery time. The lead time shown on a Passport screen is for the base motor only, modifications will add to actual lead time.


17

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Component ClassInverter Duty General Purpose SeriesCM102 Family - Enclosed EE Cast Iron AC Motors

Construction Features

Electrical Characteristics Key InformationPhase: 3 Definitions:

Frequency: 60 Hz Duty Cycle: Continuous CM102 motors meet the EPAct efficiency levels. Ambient: 40° C Insulation: Class F

Service Factor: 1.00 Temp. Rise: Class F Warranty (From Date Of Manufacture /

From Date Of Installation):

Application InformationCast Iron general purpose CM102 AC motors are an ideal choice for applications such as: Fans, Blowers, Compressors, Pumps and Conveyors.

(24 / 12)

Nameplate Agency Approvals:CE, CSA, UR

180T - 360T FramesMaterials: Cast iron frame and end shields, fabricated steel conduit box

and fan cover (180T - 210T frames), Cast Iron frame, end shields, conduit box and fan cover (320T - 360T frames).

Conduit Box: F1, Diagonally split, rotatable in 90 degree increments

Bearing Type: Ball

Bearing Protection: Slingers

Shaft Material: High strength carbon steel

Nameplate Material: Aluminum

Drain Type & Location: Weep holes both ends

Additional Features: Insulation system exceeds NEMA MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

CM102 Family - Enclosed EE Cast Iron AC Motors

18

General

Information

CM

100C

M 200

CM

300F

ootnotes

Component Class, Inverter Duty General Purpose SeriesCM102 - Enclosed EE Cast Iron AC Motors


RPM Class Torque/Spd Stock CM102- PriceTEFC 3 3600 230/460 EE CT 10:1 Yes 182T FC00336AEHHA 9 $605TEFC 3 3600 575 EE CT 10:1 Yes 182T FC00336CEHHA 9 $605TEFC 3 1800 230/460 EE CT 10:1 Yes 182T FC00318AEHHA 9 $575TEFC 3 1800 575 EE CT 10:1 Yes 182T FC00318CEHHA 9 $575TEFC 3 1200 230/460 EE CT 10:1 Yes 213T FC00312AEHHA 9 $742TEFC 3 1200 575 EE CT 10:1 Yes 213T FC00312CEHHA 9 $742TEFC 5 3600 230/460 EE CT 4:1 Yes 184T FC00536AEKHA 9 $693TEFC 5 3600 575 EE CT 4:1 Yes 184T FC00536CEKHA 9 $693TEFC 5 1800 230/460 EE CT 4:1 Yes 184T FC00518AEKHA 9 $651TEFC 5 1800 575 EE CT 4:1 Yes 184T FC00518CEKHA 9 $651TEFC 5 1200 230/460 EE CT 10:1 Yes 215T FC00512AEHHA 9 $1,015TEFC 5 1200 575 EE CT 10:1 Yes 215T FC00512CEHHA 9 $1,015TEFC 7.5 3600 230/460 EE CT 4:1 Yes 213T FC7F536AEKHA 9 $828TEFC 7.5 3600 575 EE CT 4:1 Yes 213T FC7F536CEKHA 9 $828TEFC 7.5 1800 230/460 EE CT 4:1 Yes 213T FC7F518AEKHA 9 $797TEFC 7.5 1800 575 EE CT 4:1 Yes 213T FC7F518CEKHA 9 $797TEFC 7.5 1200 230/460 EE CT 10:1 Yes 254T FC7F512AEHHA 9 $1,372TEFC 7.5 1200 575 EE CT 10:1 Yes 254T FC7F512CEHHA 9 $1,372TEFC 10 3600 230/460 EE CT 2:1 Yes 215T FC01036AEJHA 9 $956TEFC 10 3600 575 EE CT 2:1 Yes 215T FC01036CEJHA 9 $956TEFC 10 1800 230/460 EE CT 2:1 Yes 215T FC01018AEJHA 9 $878TEFC 10 1800 575 EE CT 2:1 Yes 215T FC01018CEJHA 9 $878TEFC 10 1200 230/460 EE CT 4:1 Yes 256T FC01012AEKHA 9 $1,674TEFC 10 1200 575 EE CT 4:1 Yes 256T FC01012CEKHA 9 $1,674TEFC 15 3600 230/460 EE CT 4:1 Yes 254T FC01536AEKHA 9 $1,327TEFC 15 3600 575 EE CT 4:1 Yes 254T FC01536CEKHA 9 $1,327TEFC 15 1800 230/460 EE CT 2:1 Yes 254T FC01518AEJHA 9 $1,213TEFC 15 1800 575 EE CT 2:1 Yes 254T FC01518CEJHA 9 $1,213TEFC 15 1200 230/460 EE CT 10:1 Yes 284T FC01512AEHHA 9 $2,011TEFC 15 1200 575 EE CT 10:1 Yes 284T FC01512CEHHA 9 $2,011TEFC 20 3600 230/460 EE CT 2:1 Yes 256T FC02036AEJHA 9 $1,590TEFC 20 3600 575 EE CT 2:1 Yes 256T FC02036CEJHA 9 $1,590TEFC 20 1800 230/460 EE CT 2:1 Yes 256T FC02018AEJHA 9 $1,441TEFC 20 1800 575 EE CT 2:1 Yes 256T FC02018CEJHA 9 $1,441TEFC 20 1200 230/460 EE CT 4:1 Yes 286T FC02012AEKHA 9 $2,450TEFC 20 1200 575 EE CT 4:1 Yes 286T FC02012CEKHA 9 $2,450TEFC 25 3600 230/460 EE CT 4:1 Yes 284TS FC02536AEKHA 9 $1,801TEFC 25 3600 575 EE CT 4:1 Yes 284TS FC02536CEKHA 9 $1,801TEFC 25 1800 230/460 EE CT 2:1 Yes 284T FC02518AEJHA 9 $1,726TEFC 25 1800 575 EE CT 2:1 Yes 284T FC02518CEJHA 9 $1,726TEFC 25 1200 230/460 EE CT 4:1 Yes 324T FC02512AEKHA 9 $2,980TEFC 25 1200 575 EE CT 4:1 Yes 324T FC02512CEKHA 9 $2,980TEFC 30 3600 230/460 EE CT 10:1 Yes 286TS FC03036AEHHA 9 $2,112TEFC 30 3600 575 EE CT 10:1 Yes 286TS FC03036CEHHA 9 $2,112TEFC 30 1800 230/460 EE CT 2:1 Yes 286T FC03018AEJHA 9 $2,011TEFC 30 1800 575 EE CT 2:1 Yes 286T FC03018CEJHA 9 $2,011TEFC 30 1200 230/460 EE CT 4:1 Yes 326T FC03012AEKHA 9 $3,282TEFC 30 1200 575 EE CT 4:1 Yes 326T FC03012CEKHA 9 $3,282TEFC 40 3600 230/460 EE CT 4:1 Yes 324TS FC04036AEKHA 9 $2,692TEFC 40 3600 575 EE CT 4:1 Yes 324TS FC04036CEKHA 9 $2,692TEFC 40 1800 230/460 EE CT 2:1 Yes 324T FC04018AEJHA 9 $2,670TEFC 40 1800 575 EE CT 2:1 Yes 324T FC04018CEJHA 9 $2,670TEFC 40 1200 230/460 EE CT 2:1 Yes 364T FC04012AEJHA 9 $4,448TEFC 40 1200 575 EE CT 2:1 Yes 364T FC04012CEJHA 9 $4,448


19

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Catalog String Notes US ListRPM Class Torque/Spd Stock CM102- Price

TEFC 50 3600 230/460 EE CT 2:1 Yes 326TS FC05036AEJHA 9 $3,417TEFC 50 3600 575 EE CT 2:1 Yes 326TS FC05036CEJHA 9 $3,417TEFC 50 1800 230/460 EE CT 2:1 Yes 326T FC05018AEJHA 9 $2,788TEFC 50 1800 575 EE CT 2:1 Yes 326T FC05018CEJHA 9 $2,788TEFC 50 1200 575 EE CT 2:1 Yes 365T FC05012CEJHA 9 $5,179



RPM Class Torque/Spd Stock CM102- PriceTEFC 3 3600 230/460 EE CT 10:1 Yes 182TCY FC00336AEHCA 9 $667TEFC 3 1800 230/460 EE CT 10:1 Yes 182TCY FC00318AEHCA 9 $637TEFC 3 1200 230/460 EE CT 10:1 Yes 213TCY FC00312AEHCA 9 $805TEFC 5 3600 230/460 EE CT 4:1 Yes 184TCY FC00536AEKCA 9 $756TEFC 5 1800 230/460 EE CT 4:1 Yes 184TCY FC00518AEKCA 9 $713TEFC 5 1200 230/460 EE CT 10:1 Yes 215TCY FC00512AEHCA 9 $1,077TEFC 7.5 3600 230/460 EE CT 4:1 Yes 213TCY FC7F536AEKCA 9 $892TEFC 7.5 1800 230/460 EE CT 4:1 Yes 213TCY FC7F518AEKCA 9 $859TEFC 7.5 1200 230/460 EE CT 10:1 Yes 254TCY FC7F512AEHCA 9,47 $1,454TEFC 10 3600 230/460 EE CT 2:1 Yes 215TCY FC01036AEJCA 9 $1,018TEFC 10 1800 230/460 EE CT 2:1 Yes 215TCY FC01018AEJCA 9 $940TEFC 10 1200 230/460 EE CT 4:1 Yes 256TCY FC01012AEKCA 9 $1,756TEFC 15 3600 230/460 EE CT 4:1 Yes 254TCY FC01536AEKCA 9,47 $1,417TEFC 15 1800 230/460 EE CT 2:1 Yes 254TCY FC01518AEJCA 9,47 $1,303TEFC 15 1200 230/460 EE CT 10:1 Yes 284TC FC01512AEHCA 9 $2,134TEFC 20 3600 230/460 EE CT 2:1 Yes 256TCY FC02036AEJCA 9,47 $1,680TEFC 20 1800 230/460 EE CT 2:1 Yes 256TCY FC02018AEJCA 9,47 $1,531TEFC 20 1200 230/460 EE CT 4:1 Yes 286TC FC02012AEKCA 9 $2,574TEFC 25 3600 230/460 EE CT 4:1 Yes 284TSC FC02536AEKCA 9 $1,924TEFC 25 1800 230/460 EE CT 2:1 Yes 284TC FC02518AEJCA 9 $1,850TEFC 30 3600 230/460 EE CT 10:1 Yes 286TSC FC03036AEHCA 9 $2,236TEFC 30 1800 230/460 EE CT 2:1 Yes 286TC FC03018AEJCA 9 $2,134



20

General

Information

CM

100C

M 200

CM

300F

ootnotes





CONNECTIONS: Final connect dual to single voltage.107 High Voltage Connection (price by frame size) 180-320 $162108 Low Voltage Connection (price by frame size) 360 $216

LEAD TERMINALS: Addition of lead terminals to wires in conduit box.135 Compression type (Burndy, etc.) lead lugs All $270

MOUNTING: Move conduit box to allow different mounting configurations.140 F-1 to F-2 180-280 $251

Note: Not available on L180-L210 frames 320-449 $376 141 F-1 to W6 180-280 $251




Note: Not available on L180-L210 frames 320-449 $376 SPACE HEATERS:


440-L449 $589THERMAL PROTECTION: Addition of thermostats.






21

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Component ClassInverter Duty General Purpose SeriesCM103 Family - Enclosed EE/PE/NP AC Motors



Frequency: 60 Hz Duty Cycle: Continuous EE = Energy Efficient motors that meet EPAct efficiency levels.Ambient: 40° C Insulation: Class F

Service Factor: 1.00 Temp. Rise: Class F PE = Premium Efficient motors that exceed EPAct efficiency levels

NP = NEMA Premium efficient motors

Application InformationDesigned for all general purpose industrial applications in a dusty, dirty, and/or humid environment. Enclosed motors reduce the exchange of air between the inside and the outside of the motor.

Warranty (From Date Of Manufacture / From Date Of Installation):

EE (24 / 12), PE (36 / 24), NP (36 / 24)Nameplate Agency Approvals:CE, CSA, UR

48 - 140T FramesMaterials: Steel frame, conduit box and fan shroud; cast aluminum end

shields.Conduit Box: Oversized, top mounted with F1 & F2 lead outletsBearing Type: Double shielded ball bearingsBearing Protection: Permanently lubricated with moisture resistant greaseShaft Material: High strength carbon steelNameplate Material: Adhesive MylarDrain Type & Location: Weep hole in both end shieldsAdditional Features: Insulation system on all EE, PE & NP motors exceeds NEMA

MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

180T - 449T FramesMaterials: Cast iron frame & end shield; steel fan shroud and conduit box Conduit Box: F1 location, diagonally split, rotatable in 90 degree incrementsBearing Type: Permanently lubricated, double shielded ball bearings (180T -

360T frames); regreasable, open ball bearings with PLS (400T - 449T frames)

Bearing Protection: Shaft slinger on drive endShaft Material: High strength carbon steelNameplate Material: Stainless SteelDrain Type & Location: Weep holes in both end shieldsAdditional Features: Insulation system on all EE, PE & NP motors exceeds NEMA

MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

CM103 Family - Enclosed EE/PE/NP AC Motors

22

General

Information

CM

100C

M 200

CM

300F

ootnotes

Component Class, Inverter Duty General Purpose SeriesCM103 - Enclosed SE/EE/PE/NP AC Motors


RPM Class Torque/Spd Stock CM103- PriceTENV 0.17 1200 208-230/460 EE CT 4:1 Yes 48 NVF1712GEKHA 15 $483TENV 0.25 3600 208-230/460 EE CT 4:1 N 48 NVF2536GEKHA $410TENV 0.25 1800 208-230/460 EE CT 4:1 Yes 48 NVF2518GEKHA 15 $410TENV 0.25 1800 230/460 EE CT 10:1 N 56 NVF2518AEHHA $410TENV 0.25 1800 208-230/460 EE CT 1000:1 Yes 56 NVF2518GEZHA $388TENV 0.25 1800 230/460 PE CT 1000:1 N 56 NVF2518APZHA $559TENV 0.25 1200 230/460 EE CT 10:1 N 56 NVF2512AEHHA $556TENV 0.25 1200 230/460 PE CT 1000:1 N 56 NVF2512APZHA $667TEFC 0.25 900 208-230/460 EE CT 4:1 N 56 FCF2509GEKHA $650TENV 0.33 3600 208-230/460 EE CT 4:1 Yes 48 NVF3336GEKHA 15 $410TENV 0.33 3600 230/460 EE CT 10:1 N 56 NVF3336AEHHA $417TENV 0.33 3600 230/460 PE CT 1000:1 N 56 NVF3336APZHA $493TENV 0.33 1800 208-230/460 EE CT 4:1 Yes 48 NVF3318GEKHA 15 $427TENV 0.33 1800 230/460 EE CT 10:1 Yes 56 NVF3318AEHHA $467TEFC 0.33 1800 208-230/460 EE CT 4:1 Yes 56 FCF3318GEKHA $382TENV 0.33 1800 230/460 PE CT 1000:1 Yes 56 NVF3318APZHA $575TENV 0.33 1200 230/460 EE CT 10:1 Yes 56 NVF3312AEHHA $551TENV 0.33 1200 230/460 PE CT 1000:1 Yes 56 NVF3312APZHA $676TEFC 0.33 900 208-230/460 EE CT 4:1 N 56 FCF3309GEKHA $692TEFC 0.5 3600 208-230/460 EE CT 4:1 Yes 48 FC0F536GEKH8A 15 $424TEFC 0.5 3600 208-230/460 EE CT 4:1 N 56 FC0F536GEKH5A $449TEFC 0.5 3600 230/460 PE CT 10:1 Yes 56 FC0F536APHHA $513TEFC 0.5 1800 208-230/460 EE CT 4:1 Yes 56 FC0F518GEKHB 15 $439TEFC 0.5 1800 230/460 PE CT 10:1 Yes 56 FC0F518APHHA $592TEFC 0.5 1200 208-230/460 EE CT 1000:1 Yes 56 FC0F512GEZHA 15 $529TEFC 0.5 1200 230/460 PE CT 10:1 Yes 56 FC0F512APHHA $723TEFC 0.5 900 208-230/460 EE CT 4:1 N 56 FC0F509GEKHA $724TEFC 0.75 3600 208-230/460 EE CT 4:1 Yes 56 FCF7536GEKHA $471TEFC 0.75 3600 230/460 PE CT 10:1 Yes 56 FCF7536APHHA $561TEFC 0.75 1800 208-230/460 EE CT 4:1 Yes 56 FCF7518GEKHB $452TEFC 0.75 1800 230/460 PE CT 10:1 Yes 56 FCF7518APHHA $629TEFC 0.75 1200 208-230/460 EE CT 4:1 Yes 56 FCF7512GEKHA $593TEFC 0.75 1200 230/460 EE CT 4:1 Yes 143T FCF7512AEKHA $593TEFC 0.75 1200 230/460 PE CT 20:1 Yes 143T FCF7512APMHA 50 $951TEFC 0.75 1200 230/460 PE CT 1000:1 N 143T FCF7512APZHA $776TEFC 0.75 900 208-230/460 EE CT 4:1 N 56 FCF7509GEKHA $758TEFC 0.75 900 230/460 EE CT 4:1 Yes 145T FCF7509AEKHA $758TEFC 1 3600 208-230/460 EE CT 4:1 Yes 56 FC00136GEKHA $512TENV 1 3600 230/460 PE CT 10:1 Yes 56 NV00136APHHA $606TEFC 1 3600 230/460 NP CT 20:1 Yes 143T FC00136ANMHA 50 $770TEFC 1 3600 230/460 PE CT 10:1 N 143T FC00136APHHA $551TEFC 1 1800 208-230/460 EE CT 4:1 Yes 56 FC00118GEKHA $430TEFC 1 1800 230/460 EE CT 4:1 Yes 143T FC00118AEKHA $454TEFC 1 1800 230/460 PE CT 10:1 Yes 56 FC00118APHHA $640TEFC 1 1800 230/460 NP CT 20:1 Yes 143T FC00118ANMHA 50 $789TEFC 1 1800 230/460 PE CT 10:1 Yes 143T FC00118APHHA $658TEFC 1 1200 230/460 EE CT 4:1 N 56 FC00112AEKH5A $623TEFC 1 1200 230/460 EE CT 4:1 Yes 145T FC00112AEKH4A $623TEFC 1 1200 230/460 PE CT 20:1 N 56 FC00112APMHNA $778TEFC 1 1200 230/460 PE CT 20:1 Yes 145T FC00112APMHYA 50 $943TEFC 1 1200 230/460 NP CT 20:1 Yes 145T FC00112ANMHA $778TEFC 1.5 3600 230/460 EE CT 4:1 N 56 FC1F536AEKH5A $576TEFC 1.5 3600 230/460 EE CT 4:1 Yes 143T FC1F536AEKH4A $576TEFC 1.5 3600 230/460 PE CT 20:1 N 56 FC1F536APMH5A $692


23

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 1.5 3600 230/460 PE CT 20:1 Yes 143T FC1F536APMH4A 50 $854TEFC 1.5 3600 230/460 NP CT 20:1 N 145T FC1F536ANMHA $692TEFC 1.5 1800 230/460 EE CT 4:1 N 56 FC1F518AEKHA $529TEFC 1.5 1800 208-230/460 EE CT 4:1 Yes 56 FC1F518GEKHA 2 $458TEFC 1.5 1800 230/460 EE CT 4:1 Yes 145T FC1F518AEKHA $529TEFC 1.5 1800 230/460 PE CT 20:1 N 56 FC1F518APMH5A $682TEFC 1.5 1800 230/460 PE CT 20:1 Yes 145T FC1F518APMH4A 50 $833TEFC 1.5 1800 230/460 NP CT 20:1 Yes 145T FC1F518ANMHA $673TEFC 1.5 1200 230/460 EE CT 4:1 Yes 145T FC1F512AEKHA $676TEFC 1.5 1200 230/460 EE VT 10:1 (2) Yes 182T FC1F512AEVHA 9 $715TEFC 1.5 1200 230/460 NP CT 10:1 Yes 182T FC1F512ANHHA 9 $795TEFC 2 3600 230/460 EE CT 10:1 Yes 56 FC00236AEHHA $635TEFC 2 3600 230/460 EE CT 4:1 Yes 145T FC00236AEKHA $635TEFC 2 3600 230/460 PE CT 20:1 N 56 FC00236APMHNA $773TEFC 2 3600 230/460 PE CT 20:1 Yes 145T FC00236APMHYA 50 $936TEFC 2 3600 230/460 NP CT 20:1 N 145T FC00236ANMHA $773TEFC 2 1800 230/460 EE CT 4:1 N 56 FC00218AEKHA $561TEFC 2 1800 208-230/460 EE VT 10:1 (2) Yes 56 FC00218GEVHA 2 $477TEFC 2 1800 230/460 EE CT 4:1 Yes 145T FC00218AEKHB $561TEFC 2 1800 230/460 PE CT 20:1 N 56 FC00218APMHNA $719TEFC 2 1800 230/460 PE CT 20:1 Yes 145T FC00218APMHYA 50 $876TEFC 2 1800 230/460 NP CT 20:1 Yes 145T FC00218ANMHA $692TEFC 2 1200 230/460 EE VT 10:1 Yes 184T FC00212AEVHA 9 $664TEFC 2 1200 230/460 NP CT 10:1 Yes 184T FC00212ANHHA 9 $879TEFC 3 3600 208-230/460 EE CT 4:1 N 56 FC00336GEKHA $672TEFC 3 3600 230/460 EE CT 4:1 Yes 145T FC00336AEKHA $672TEFC 3 3600 230/460 NP CT 10:1 Yes 182T FC00336ANHHA 9 $781TEFC 3 1800 230/460 NP CT 10:1 N L182T FC00318ANHHA $737TEFC 3 1800 200/208 PE CT 10:1 Yes 182T FC00318HPHHA 75 $737TEFC 3 1200 230/460 NP CT 10:1 Yes 213T FC00312ANHHA 9 $992TEFC 3 900 460 PE CT 10:1 N L215T FC00309BPHHA $1,532TEFC 5 3600 230/460 NP CT 10:1 Yes 184T FC00536ANHHA 9 $909TEFC 5 1800 200/208 EE VT 10:1 Yes 184T FC00518HEVHA 75 $768TEFC 5 1800 230/460 NP CT 10:1 Yes 184T FC00518ANHHA 9 $848TEFC 5 1200 230/460 NP CT 10:1 Yes 215T FC00512ANHHA 9 $1,395TEFC 5 900 460 PE CT 4:1 (10) N 254T FC00509BPKHA $1,831TEFC 7.5 3600 230/460 NP CT 10:1 Yes 213T FC7F536ANHHA $1,255TEFC 7.5 1800 230/460 PE CT 10:1 Yes 213T FC7F518APHHA $1,057TEFC 7.5 1800 230/460 NP CT 10:1 Yes 213T FC7F518ANHHA $1,142TEFC 7.5 1200 230/460 NP CT 10:1 Yes 254T FC7F512ANHHA 9 $1,780TEFC 7.5 900 460 PE CT 4:1 (10) N 256T FC7F509BPKHA $3,096TEFC 10 3600 230/460 NP CT 10:1 Yes 215T FC01036ANHHA 9 $1,289TEFC 10 1800 230/460 NP CT 10:1 Yes 215T FC01018ANHHA 9 $1,174TEFC 10 1800 230/460 PE CT 10:1 Yes L215T FC01018APHHA $1,174TEFC 10 1200 230/460 NP CT 10:1 Yes 256T FC01012ANHHA 9 $2,188TEFC 10 900 460 PE CT 4:1 (10) N 284T FC01009BPKHA $3,100TEFC 15 3600 230/460 NP CT 4:1 (10) Yes 254T FC01536ANKHA $1,927TEFC 15 1800 230/460 NP CT 10:1 Yes 254T FC01518ANHHA 9 $1,541TEFC 15 1800 230/460 PE CT 10:1 Yes 254T FC01518APHHA $1,541TEFC 15 1200 230/460 NP CT 10:1 Yes 284T FC01512ANHHA 9 $2,712TEFC 15 900 460 PE CT 4:1 (10) N 286T FC01509BPKHA $3,894TEFC 20 3600 230/460 NP CT 4:1 (10) Yes 256T FC02036ANKHA $2,042TEFC 20 1800 230/460 NP CT 10:1 Yes 256T FC02018ANHHA 9 $1,842TEFC 20 1800 230/460 PE CT 10:1 Yes 256T FC02018APHHA $1,842TEFC 20 1200 230/460 NP CT 10:1 Yes 286T FC02012ANHHA 9 $3,397TEFC 20 900 460 PE CT 4:1 (10) N 324T FC02009BPKHA $4,881TEFC 25 3600 230/460 NP CT 4:1 (10) Yes 284TS FC02536ANKHA $2,528TEFC 25 1800 230/460 NP CT 10:1 Yes 284T FC02518ANHHA 9 $2,320TEFC 25 1800 230/460 PE CT 10:1 Yes 284T FC02518APHHA $2,320


24

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 25 1200 230/460 NP CT 4:1 (10) N 324T FC02512ANKHA $3,918TEFC 25 900 460 PE CT 4:1 (10) N 326T FC02509BPKHA $5,798TEFC 30 3600 230/460 NP VT 10:1 (2) Yes 286TS FC03036ANVHA 9 $2,876TEFC 30 1800 230/460 NP CT 10:1 Yes 286T FC03018ANHHA 9 $2,714TEFC 30 1800 230/460 PE CT 10:1 Yes 286T FC03018APHHA $2,714TEFC 30 1200 230/460 NP CT 4:1 (10) N 326T FC03012ANKHA $4,465TEFC 30 900 460 PE CT 4:1 (10) N 364T FC03009BPKHA $6,588TEFC 40 3600 230/460 NP CT 4:1 (10) N 324TS FC04036ANKHA $3,527TEFC 40 1800 230/460 NP CT 4:1 (10) Yes 324T FC04018ANKHA $3,498TEFC 40 1200 230/460 NP CT 4:1 (10) N 364T FC04012ANKHA $5,900TEFC 40 900 460 PE CT 4:1 (10) N 365T FC04009BPKHA $8,023TEFC 50 3600 230/460 NP CT 4:1 (10) N 326TS FC05036ANKHA $4,505TEFC 50 1800 230/460 NP CT 4:1 (10) Yes 326T FC05018ANKHA $4,096TEFC 50 1200 230/460 NP CT 4:1 (10) N 365T FC05012ANKHA $6,885TEFC 50 1200 230/460 EE VT 10:1 Yes 365T FC05012AEVHA 9 $5,179TEFC 50 900 460 PE CT 4:1 (10) N 404T FC05009BPKHA $9,441TEFC 60 3600 230/460 NP CT 4:1 (10) N 364TS FC06036ANKHA $6,012TEFC 60 3600 230/460 EE VT 10:1 (2) Yes 364TS FC06036AEVHB $5,215TEFC 60 1800 230/460 NP CT 4:1 (10) Yes 364T FC06018ANKHA $5,882TEFC 60 1800 230/460 EE VT 10:1 (2) Yes 364T FC06018AEVHA $5,104TEFC 60 1200 230/460 EE VT 10:1 (2) Yes 404T FC06012AEVHA $6,808TEFC 60 1200 230/460 NP CT 4:1 (10) N 404T FC06012ANKHA $7,864TEFC 60 1200 230/460 EE VT 10:1 (2) Yes 404T FC06012AEVHA $6,808TEFC 60 900 460 PE CT 4:1 (10) N 405T FC06009BPKHA $10,853TEFC 75 3600 230/460 NP CT 4:1 (10) N 365TS FC07536ANKHA $7,433TEFC 75 3600 230/460 EE VT 10:1 (2) Yes 365TS FC07536AEVHB $6,436TEFC 75 1800 230/460 NP CT 4:1 (10) N 365T FC07518ANKHA $7,181TEFC 75 1800 230/460 EE VT 10:1 (2) Yes 365T FC07518AEVHA $5,723TEFC 75 1200 230/460 NP CT 4:1 (10) N 405T FC07512ANKHA $8,788TEFC 75 1200 230/460 EE VT 10:1 (2) Yes 405T FC07512AEVHB $7,601TEFC 75 900 460 PE CT 4:1 (10) N 444T FC07509BPKHA $14,053TEFC 100 3600 230/460 NP CT 4:1 (10) N 405TS FC10036ANKHA $9,508TEFC 100 3600 230/460 EE VT 10:1 Yes 405TS FC10036AEVHA 9 $8,220TEFC 100 1800 460 NP CT 4:1 (10) Yes 405T FC10018BNKHA $8,738TEFC 100 1800 230/460 EE VT 10:1 (2) Yes 405TS FC10018AEVHB $7,558TEFC 100 1200 230/460 NP CT 4:1 (10) N 444T FC10012ANKHA $13,793TEFC 100 1200 230/460 EE VT 10:1 Yes 444T FC10012AEVHA 9 $10,028TEFC 125 3600 460 EE VT 10:1 (2) Yes 444TS FC12536BEVHA $10,517TEFC 125 3600 460 NP CT 4:1 (10) N 444TS FC12536BNKHA $12,177TEFC 125 1800 460 EE VT 10:1 (2) Yes 444T FC12518BEVHA $9,725TEFC 125 1800 460 NP CT 4:1 (10) Yes 444T FC12518BNKHA $11,258TEFC 125 1800 460 EE VT 10:1 (2) Yes 444TS FC12518BEVHA $9,725TEFC 125 1200 460 EE VT 10:1 (2) Yes 445T FC12512BEVHA $12,209TEFC 125 1200 460 NP CT 4:1 (10) N 445T FC12512BNKHA $14,146TEFC 150 3600 460 EE VT 10:1 (2) Yes 445TS FC15036BEVHA $12,772TEFC 150 3600 460 NP CT 4:1 (10) N 445TS FC15036BNKHA $14,801TEFC 150 1800 460 EE VT 10:1 (2) Yes 445T FC15018BEVHA $11,418TEFC 150 1800 460 NP CT 4:1 (10) Yes 445T FC15018BNKHA $13,225TEFC 150 1800 460 EE VT 10:1 (2) Yes 445TS FC15018BEVHA $11,418TEFC 150 1200 460 EE VT 10:1 (2) Yes 445T FC15012BEVUA 5 $13,910TEFC 150 1200 460 EE VT 10:1 (2) Yes 445TS FC15012BEVHB $13,910TEFC 150 1200 460 NP CT 4:1 (10) N 445T FC15012BNKHA $16,126TEFC 200 3600 460 EE VT 10:1 (2) Yes 445TS FC20036BEVHA 4 $16,338TEFC 200 3600 460 NP CT 4:1 (10) N 445TS FC20036BNKHA $18,945TEFC 200 1800 460 EE VT 10:1 (2) Yes 445T FC20018BEVUA 4,5 $13,983TEFC 200 1800 460 NP CT 2:1 (10) Yes 447T FC20018BNJUA 5 $15,607TEFC 200 1800 460 EE VT 10:1 (2) Yes 445TS FC20018BEVHB $14,487TEFC 200 1800 460 PE CT 2:1 (10) N 447TS FC20018BPJHA $15,607TEFC 200 1200 460 EE VT 10:1 Yes 447T FC20012BEVUA 4,5 $16,329


25

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 200 1200 460 NP CT 2:1 (10) N 449T FC20012BNJUA 5 $18,271TEFC 250 3600 460 EE VT 10:1 Yes 447TS FC25036BEVHA 4 $20,789TEFC 250 3600 460 NP CT 2:1 (10) N 447TS FC25036BNJHA $23,454TEFC 250 1800 460 EE VT 10:1 Yes 447TS FC25018BEVHB 4 $16,598TEFC 250 1800 460 EE VT 10:1 Yes 447T FC25018BEVUA 4,5 $16,598TEFC 250 1800 460 NP CT 2:1 (10) N 449T FC25018BNJUA 5 $18,582TEFC 250 1200 460 EE VT 10:1 Yes 449T FC25012BEVUA 4,5 $21,397TEFC 250 1200 460 NP CT 2:1 (10) N 449T FC25012BNJUA 5 $24,162TEFC 300 3600 460 NP CT 2:1 (10) N 449TS FC30036BNJHA $29,553TEFC 300 1800 460 EE VT 10:1 Yes 449TS FC30018BEVHA 4 $19,617TEFC 300 1800 460 NP CT 2:1 (10) N 449T FC30018BNJUA 5 $22,094TEFC 350 3600 460 NP CT 2:1 (10) N 449TS FC35036BNJHA $33,577TEFC 350 1800 460 NP CT 2:1 (10) N 449T FC35018BNJUA 5 $26,027


C Face Foot Mounted IP44Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Catalog String Notes US List

RPM Class Torque/Spd Stock CM103- PriceTENV 0.25 3600 208-230/460 EE CT 4:1 N 56C NVF2536GEKCA $440TENV 0.25 1800 230/460 EE CT 10:1 Yes 56C NVF2518AEHCA 15 $466TENV 0.25 1200 230/460 EE CT 10:1 Yes 56C NVF2512AEHCA 15 $586TEFC 0.25 900 208-230/460 EE CT 4:1 Yes 56C FCF2509GEKCA $681TENV 0.33 3600 230/460 EE CT 10:1 Yes 56C NVF3336AEHCA 15 $447TENV 0.33 1800 230/460 EE CT 10:1 Yes 56C NVF3318AEHCA 15 $471TEFC 0.33 1800 208-230/460 EE CT 4:1 Yes 56C FCF3318GEKCA 2 $405TENV 0.33 1200 230/460 EE CT 10:1 Yes 56C NVF3312AEHCA 15 $586TEFC 0.33 900 208-230/460 EE CT 4:1 N 56C FCF3309GEKCA $722TEFC 0.5 3600 208-230/460 EE CT 4:1 Yes 56C FC0F536GEKCA 15 $453TEFC 0.5 1800 200-208 EE CT 4:1 Yes 56C FC0F518HEKCA $500TEFC 0.5 1800 208-230/460 EE CT 4:1 Yes 56C FC0F518GEKCA 2 $436TEFC 0.5 1200 208-230/460 EE CT 4:1 Yes 56C FC0F512GEKCA 15 $611TEFC 0.5 900 208-230/460 EE CT 4:1 N 56C FC0F509GEKCA $755TEFC 0.75 3600 208-230/460 EE CT 4:1 Yes 56C FCF7536GEKCA 15 $480TEFC 0.75 1800 208-230/460 EE CT 4:1 Yes 56C FCF7518GEKCB 15 $529TEFC 0.75 1800 200-208 EE CT 4:1 Yes 56C FCF7518HEKCA $520TEFC 0.75 1200 208-230/460 EE CT 4:1 Yes 56C FCF7512GEKCA 15 $623TEFC 0.75 1200 230/460 EE CT 4:1 N 143TC FCF7512AEKCA $623TEFC 0.75 900 208-230/460 EE CT 4:1 N 56C FCF7509GEKCA $789TEFC 0.75 900 230/460 EE CT 4:1 N 145TC FCF7509AEKCA $789TEFC 1 3600 208-230/460 EE CT 4:1 Yes 56C FC00136GEKCA 15 $512TEFC 1 1800 208-230/460 EE CT 4:1 Yes 56C FC00118GEKCB 15 $536TEFC 1 1800 200-208 EE CT 4:1 Yes 56C FC00118HEKCA $545TEFC 1 1800 230/460 EE CT 4:1 Yes 143TC FC00118AEKCB $556TEFC 1 1200 230/460 EE CT 4:1 Yes 56C FC00112AEKC5A $626TEFC 1 1200 230/460 EE CT 4:1 Yes 145TC FC00112AEKC4A $626TEFC 1.5 3600 230/460 EE CT 4:1 Yes 56C FC1F536AEKC5A $581TEFC 1.5 3600 230/460 EE CT 4:1 N 143TC FC1F536AEKC4A $581TEFC 1.5 1800 230/460 EE CT 4:1 Yes 56C FC1F518AEKCA $576TEFC 1.5 1800 200-208 EE CT 4:1 Yes 145TC FC1F518HEKCA $563TEFC 1.5 1800 208-230/460 EE CT 4:1 Yes 56C FC1F518GEKCA 2 $482TEFC 1.5 1800 230/460 EE CT 4:1 Yes 145TC FC1F518AEKCB $576TEFC 1.5 1200 230/460 EE CT 4:1 N 145TC FC1F512AEKCA $651TEFC 1.5 1200 230/460 EE CT 10:1 Yes 182TCY FC1F512AEHCA 9,47 $794TEFC 2 3600 230/460 EE CT 4:1 N 56C FC00236AEKC5A $639TEFC 2 3600 230/460 EE CT 4:1 N 145TC FC00236AEKC4A $639


26

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 2 1800 230/460 EE CT 4:1 Yes 56C FC00218AEKCA $606TEFC 2 1800 200-208 EE CT 4:1 Yes 145TC FC00218HEKCA $599TEFC 2 1800 208-230/460 EE CT 4:1 Yes 56C FC00218GEKCA 2 $497TEFC 2 1800 230/460 EE CT 4:1 Yes 145TC FC00218AEKCB $606TEFC 2 1200 230/460 EE CT 10:1 Yes 184TCY FC00212AEHCA 9,47 $864TEFC 3 3600 208-230/460 EE CT 4:1 N 56C FC00336GEKCA $676TEFC 3 3600 230/460 PE CT 10:1 Yes 182TCY FC00336APHCA 9 $867TEFC 3 1800 230/460 PE CT 10:1 Yes 182TC FC00318APHCB $822TEFC 5 3600 230/460 PE CT 10:1 Yes 184TCY FC00536APHCA 9 $987TEFC 5 1800 230/460 PE CT 10:1 Yes 184TC FC00518APHCB $934TEFC 7.5 3600 230/460 PE CT 10:1 Yes 213TCY FC7F536APHCA 9 $1,171TEFC 7.5 1800 230/460 PE CT 10:1 Yes 213TC FC7F518APHCB $1,142TEFC 10 3600 230/460 PE CT 10:1 Yes 215TCY FC01036APHCA 9 $1,343TEFC 10 1800 230/460 PE CT 10:1 Yes 215TC FC01018APHCB 9 $1,259TEFC 15 3600 230/460 PE CT 10:1 Yes 254TCY FC01536APHCA 9 $1,759TEFC 15 1800 230/460 PE CT 10:1 Yes 254TC FC01518APHCB 9 $1,652TEFC 20 3600 230/460 PE CT 10:1 Yes 256TCY FC02036APHCA 9 $2,085TEFC 20 1800 230/460 PE CT 10:1 Yes 256TCY FC02018APHCA 9 $1,897TEFC 40 1800 230/460 EE VT 10:1 (2) Yes 324TC FC04018AEVCA $3,275TEFC 50 1800 230/460 EE VT 10:1 (2) Yes 326TC FC05018AEVCA $3,790TEFC 60 1800 230/460 EE VT 10:1 (2) N 364TC FC06018AEVCA $5,420TEFC 75 1800 230/460 EE VT 10:1 (2) N 365TC FC07518AEVCA $6,536TEFC 100 1800 230/460 EE VT 10:1 (2) N 405TC FC10018AEVCA $8,075TEFC 125 1800 230/460 EE VT 10:1 (2) N 444TC FC12518AEVCA $10,445TEFC 150 1800 460 EE VT 10:1 (2) N 445TC FC15018BEVCA $12,138TEFC 200 1800 460 EE VT 10:1 (2) N 445TC FC20018BEVCA $14,187


C Face, Footless IP44Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Catalog String Notes US List

RPM Class Torque/Spd Stock CM103- PriceTENV 0.25 3600 208-230/460 EE CT 4:1 N 56C NVF2536GEKFA $423TENV 0.25 1800 230/460 EE CT 10:1 Yes 56C NVF2518AEHFA 15 $442TENV 0.25 1800 230/460 PE CT 1000:1 Yes 56C NVF2518APZFA $524TENV 0.25 1200 230/460 EE CT 10:1 Yes 56C NVF2512AEHFA 15 $561TENV 0.25 1200 230/460 PE CT 1000:1 N 56C NVF2512APZFA $678TEFC 0.25 900 208-230/460 EE CT 4:1 N 56C FCF2509GEKFA $652TENV 0.33 3600 230/460 EE CT 10:1 Yes 56C NVF3336AEHFA $431TENV 0.33 3600 230/460 PE CT 1000:1 N 56C NVF3336APZFA $504TENV 0.33 1800 230/460 EE CT 10:1 Yes 56C NVF3318AEHFA 15 $418TEFC 0.33 1800 208-230/460 EE CT 4:1 Yes 56C FCF3318GEKFA 2 $389TENV 0.33 1800 230/460 PE CT 1000:1 Yes 56C NVF3318APZFA $545TENV 0.33 1200 230/460 EE CT 10:1 Yes 56C NVF3312AEHFA 15 $559TENV 0.33 1200 230/460 PE CT 1000:1 Yes 56C NVF3312APZFA $687TEFC 0.33 900 208-230/460 EE CT 4:1 N 56C FCF3309GEKFA $691TEFC 0.5 3600 208-230/460 EE CT 4:1 Yes 56C FC0F536GEKFA 15 $436TEFC 0.5 3600 230/460 PE CT 10:1 Yes 56C FC0F536APHFA $524TEFC 0.5 1800 208-230/460 EE CT 4:1 Yes 56C FC0F518GEKFB 15 $454TEFC 0.5 1800 230/460 PE CT 10:1 Yes 56C FC0F518APHFA $593TEFC 0.5 1200 208-230/460 EE CT 4:1 Yes 56C FC0F512GEKFA 15 $582TEFC 0.5 1200 230/460 PE CT 10:1 Yes 56C FC0F512APHFA $733TEFC 0.5 900 208-230/460 EE CT 4:1 Yes 56C FC0F509GEKFA $723TEFC 0.75 3600 208-230/460 EE CT 4:1 Yes 56C FCF7536GEKFA 15 $461TEFC 0.75 3600 230/460 PE CT 10:1 Yes 56C FCF7536APHFA $521TEFC 0.75 1800 208-230/460 EE CT 4:1 Yes 56C FCF7518GEKFB 15 $469TEFC 0.75 1800 230/460 PE CT 20:1 Yes 56C FCF7518APMFA $633


27

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 0.75 1200 208-230/460 EE CT 4:1 Yes 56C FCF7512GEKF5A 15 $594TEFC 0.75 1200 208-230/460 EE CT 4:1 N 143TC FCF7512GEKF4A $594TEFC 0.75 1200 230/460 PE CT 10:1 N 143TC FCF7512APHFA $749TEFC 0.75 900 208-230/460 EE CT 4:1 Yes 56C FCF7509GEKF5A $754TEFC 0.75 900 208-230/460 EE CT 4:1 Yes 145TC FCF7509GEKF4A $754TEFC 1 3600 208-230/460 EE CT 4:1 Yes 56C FC00136GEKF5A 15 $492TEFC 1 3600 208-230/460 EE CT 4:1 Yes 143TC FC00136GEKF4A 15 $492TEFC 1 3600 230/460 PE CT 10:1 Yes 56C FC00136APHFNA $617TEFC 1 3600 230/460 PE CT 10:1 Yes 143TC FC00136APHFYA 50 $700TEFC 1 3600 230/460 PE na N 143TC FC00136APXFA $617TEFC 1 1800 208-230/460 EE CT 4:1 Yes 56C FC00118GEKFB 15 $486TEFC 1 1800 208-230/460 EE CT 4:1 Yes 143TC FC00118GEKFA 2 $461TEFC 1 1800 230/460 EE CT 4:1 Yes 143TC FC00118AEKFA 15 $486TEFC 1 1800 230/460 PE CT 20:1 Yes 56C FC00118APMFA $642TEFC 1 1800 230/460 PE CT 10:1 Yes 143TC FC00118APHFA 50 $799TEFC 1 1800 230/460 PE na Yes 143TC FC00118APXFA $642TEFC 1 1200 230/460 EE CT 4:1 Yes 56C FC00112AEKF5A $620TEFC 1 1200 230/460 EE CT 4:1 Yes 145TC FC00112AEKF4A 15 $620TEFC 1 1200 230/460 PE CT 20:1 N 56C FC00112APMF5A $789TEFC 1 1200 230/460 PE CT 20:1 N 145TC FC00112APMF4A $789TEFC 1.5 3600 230/460 EE CT 4:1 Yes 56C FC1F536AEKF5A 15 $547TEFC 1.5 3600 230/460 EE CT 4:1 N 143TC FC1F536AEKF4A $572TEFC 1.5 3600 230/460 PE CT 20:1 N 56C FC1F536APMF5A $703TEFC 1.5 3600 230/460 PE CT 20:1 Yes 143TC FC1F536APMFYA 50 $865TEFC 1.5 3600 230/460 PE CT 20:1 N 143TC FC1F536APMF4A $703TEFC 1.5 1800 230/460 EE CT 4:1 Yes 56C FC1F518AEKF5A $500TEFC 1.5 1800 208-230/460 EE CT 4:1 Yes 56C FC1F518GEKF5A 2 $465TEFC 1.5 1800 208-230/460 EE CT 4:1 Yes 145TC FC1F518GEKF4A 2 $465TEFC 1.5 1800 230/460 EE CT 4:1 Yes 145TC FC1F518AEKF4A $500TEFC 1.5 1800 230/460 PE CT 20:1 Yes 56C FC1F518APMF5A $687TEFC 1.5 1800 230/460 PE CT 20:1 Yes 145TC FC1F518APMFYA 50 $844TEFC 1.5 1800 230/460 PE CT 20:1 Yes 145TC FC1F518APMF4A $687TEFC 1.5 1200 208-230/460 EE CT 4:1 Yes 145TC FC1F512GEKFA $670TEFC 1.5 1200 230/460 EE VT 10:1 (2) Yes 182TC FC1F512AEVFA $812TEFC 2 3600 230/460 EE CT 4:1 Yes 56C FC00236AEKF5A 15 $630TEFC 2 3600 230/460 EE CT 4:1 Yes 145TC FC00236AEKF4A 15 $630TEFC 2 3600 230/460 PE CT 20:1 N 56C FC00236APMF5A $784TEFC 2 3600 230/460 PE CT 20:1 Yes 145TC FC00236APMFYA 50 $947TEFC 2 3600 230/460 PE CT 20:1 N 145TC FC00236APMF4A $784TEFC 2 1800 230/460 EE CT 4:1 Yes 56C FC00218AEKFA $530TEFC 2 1800 230/460 EE CT 4:1 Yes 145TC FC00218AEKFA 15 $520TEFC 2 1800 208-230/460 EE CT 4:1 Yes 56C FC00218GEKFA 2 $483TEFC 2 1800 208-230/460 EE CT 4:1 Yes 145TC FC00218GEKFA 2 $475TEFC 2 1800 230/460 PE CT 20:1 Yes 56C FC00218APMF5A $730TEFC 2 1800 230/460 PE CT 20:1 Yes 145TC FC00218APMFYA 50 $887TEFC 2 1800 230/460 PE CT 20:1 Yes 145TC FC00218APMF4A $730TEFC 2 1200 230/460 EE VT 10:1 (2) Yes 184TC FC00212AEVFA $647TEFC 3 3600 208-230/460 EE CT 4:1 N 56C FC00336GEKF5A $647TEFC 3 3600 208-230/460 EE CT 4:1 N 145TC FC00336GEKF4A $647TEFC 3 3600 230/460 EE VT 10:1 (2) Yes 182TC FC00336AEVFA $807TEFC 3 1800 208-230/460 EE CT 4:1 Yes 145TC FC00318GEKFA $593TEFC 3 1800 208-230/460 EE VT 10:1 (2) Yes 182TC FC00318GEVFA 9,15 $580TEFC 3 1800 230/460 EE VT 10:1 (2) Yes 182TC FC00318AEVFA $770TEFC 3 1800 230/460 PE CT 10:1 Yes 182TC FC00318APHFA $842TEFC 3 1200 230/460 EE VT 10:1 (2) Yes 213TC FC00312AEVFA $982TEFC 5 3600 230/460 EE VT 10:1 (2) Yes 184TC FC00536AEVFA $920TEFC 5 1800 230/460 EE VT 10:1 (2) Yes 184TC FC00518AEVFNA $688TEFC 5 1800 230/460 EE VT 10:1 (2) Yes 184TC FC00518AEVFYA $866TEFC 5 1800 230/460 PE CT 10:1 Yes 184TC FC00518APHFA $953


28

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 5 1200 230/460 EE VT 10:1 (2) Yes 215TC FC00512AEVFA $1,326TEFC 7.5 3600 230/460 EE VT 10:1 (2) Yes 213TC FC7F536AEVFA $1,092TEFC 7.5 1800 230/460 EE VT 10:1 (2) Yes 213TC FC7F518AEVFA $1,051TEFC 7.5 1800 230/460 PE CT 10:1 Yes 213TC FC7F518APHFA $1,162TEFC 10 3600 230/460 EE VT 10:1 (2) Yes 215TC FC01036AEVFA $1,251TEFC 10 1800 230/460 EE VT 10:1 (2) Yes 215TC FC01018AEVFA $1,154TEFC 10 1800 230/460 PE CT 10:1 Yes 215TC FC01018APHFA $1,279


(2) Note: VT 10:1 (2) = Variable Torque 10:1 Speed Range (capable of 2:1 CT with fan change), must add modification code 126(10) Note: CT 2:1 (10) = Constant Torque 2:1 Speed Range (capable of 10:1 CT with fan change), must add modification code 126(10) Note: CT 4 :1 (10) = Constant Torque 4:1 Speed Range (capable of 10:1 CT with fan change), must add modification code 126


29

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Modifications Available to CM103 MotorsGeneral Information




CONDUIT BOX: Mounting of stock box kits (price includes box).101 Convert to cast iron 180-320 $188 103

360-445 $376 103102 Add auxiliary box attached to main conduit box 140-445 $618 103103 Drill drain hole 56-449 $188 103

CONNECTIONS: Final connect dual to single voltage.107 High Voltage Connection (price by frame size) 48-140 $134108 Low Voltage Connection (price by frame size) 180-320 $188

360-449 $251DRAINS: Install one automatic breather drain in each motor end bracket. Note: Mounting position must be specified.

112 Stainless steel T-drain 180-449 $618 103DRIP COVERS: Mounting of stock canopy kits (price includes kit).

116 Install canopy kit to allow for vertical shaft down operation. 48, 56, 140 $251Note: This modification does not provide vertical lifting provisions. 180-210 $251END BRACKET: Modify a foot mounted motor to include a C-Face end bracket.Note: Please add seal modification seperately if required.

120 Changing from std. end to C-face on drive end (Cast Iron N/A) 56,140 $197121 Changing from std. end to C-face with feet (Non-NEMA BA) 180-250 $493122 Changing from std. end to C-face with feet (NEMA BA) 280-360 $744

Non-Nafta motors are non-NEMA BAFAN CHANGE: Install larger fan.

126 Convert to larger fan for increased Constant Torque speed range on inverter 180-280 $314 103(increases range as noted on catalog page). 320-449 $439 103GREASE FITTINGS: Install a grease fitting on each bearing.

130 Alemite 1610 or button head zerk fitting 250-449 $188 103LEAD TERMINALS: Addition of lead terminals to wires in conduit box.

134 Addition of eyelet-type lead terminals 48,56,140 $251135 Compression type (Burndy, etc.) lead lugs 48-449 $314

MILL AND CHEMICAL DUTY: Add features for additional reliability in Mill and Chem duty applications.139 Convert to cast iron fan shroud and conduit box. 180-280 $493 103

320-400 $744 103440-449 $1,245 103




30

General

Information

CM

100C

M 200

CM

300F

ootnotes

Changes to an Order

Modifications Available to CM103 MotorsMOUNTING: Move conduit box to allow different mounting configurations.





144 F-1 to W7 180-280 $251 Note: Not available on L180-L210 frames 320-449 $376 SEALS: Addition of shaft seal.

148 Additon of V-ring rubber slinger on drive end 48-445 $251SPACE HEATERS:






31

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Component ClassInverter Duty General Purpose SeriesCM106 Family - Open EE Rolled Steel AC Motors






Application InformationRolled steel general purpose CM106 AC motors are an ideal choice for applications such as: Fans, Blowers, Compressors, Pumps & Conveyors.

(24 / 12)


180T - 280T FramesMaterials: Steel frames, conduit box and fan shroud, Cast Aluminum end

shields with steel bearing inserts (180T - 210T frames), Cast Iron end shields (250T - 280T frames). All C-face brackets are Cast Iron.

Conduit Box: F1 location. Diagonally split, rotatable in 90 degree increments

Bearing Type: Permanently lubricated, double shielded ball bearings

Bearing Protection: Shaft slinger on drive end


Nameplate Material: Aluminum

Drain Type & Location: Weep holes on both end shields

Additional Features: Insulation system exceeds NEMA MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

CM106 Family - Open EE Rolled Steel AC Motors

32

General

Information

CM

100C

M 200

CM

300F

ootnotes

Component Class, Inverter Duty General Purpose SeriesCM106 - Open EE Rolled Steel AC Motors


RPM Class Torque/Spd Stock CM106- PriceODP 3 1800 230/460 EE CT 4:1 Yes 182T DP00318AEKHA 9 $478ODP 3 1200 230/460 EE CT 4:1 Yes 213T DP00312AEKHA 9 $620ODP 5 3600 230/460 EE CT 4:1 Yes 182T DP00536AEKHA 9 $502ODP 5 1800 230/460 EE CT 4:1 Yes 184T DP00518AEKHA 9 $505ODP 5 1200 230/460 EE CT 4:1 Yes 215T DP00512AEKHA 9 $723ODP 7.5 3600 230/460 EE CT 4:1 Yes 184T DP7F536AEKHA 9 $630ODP 7.5 1800 230/460 EE CT 2:1 Yes 213T DP7F518AEJHA 9 $639ODP 7.5 1200 230/460 EE CT 4:1 Yes 254T DP7F512AEKHA 9 $879ODP 10 3600 230/460 EE CT 4:1 Yes 213T DP01036AEKHA 9 $727ODP 10 1800 230/460 EE CT 2:1 Yes 215T DP01018AEJHA 9 $729ODP 10 1200 230/460 EE CT 4:1 Yes 256T DP01012AEKHA 9 $993ODP 15 3600 230/460 EE CT 2:1 Yes 215T DP01536AEJHA 9 $875ODP 15 1800 230/460 EE CT 2:1 Yes 254T DP01518AEJHA 9 $899ODP 15 1200 230/460 EE CT 2:1 Yes 284T DP01512AEJHA 9 $1,219ODP 20 3600 230/460 EE CT 2:1 Yes 254T DP02036AEJHA 9 $995ODP 20 1800 230/460 EE CT 2:1 Yes 256T DP02018AEJHA 9 $1,052ODP 20 1200 230/460 EE CT 2:1 Yes 286T DP02012AEJHA 9 $1,448ODP 25 3600 230/460 EE CT 2:1 Yes 256T DP02536AEJHA 9 $1,168ODP 25 1800 230/460 EE CT 2:1 Yes 284T DP02518AEJHA 9 $1,190ODP 30 3600 230/460 EE CT 2:1 Yes 284TS DP03036AEJHA 9 $1,353ODP 30 1800 230/460 EE CT 2:1 Yes 286T DP03018AEJHA 9 $1,349



RPM Class Torque/Spd Stock CM106- PriceODP 3 1800 230/460 EE CT 4:1 Yes 182TC DP00318AEKCA 9 $547ODP 3 1200 230/460 EE CT 4:1 Yes 213TC DP00312AEKCA 9 $688ODP 5 3600 230/460 EE CT 4:1 Yes 182TC DP00536AEKCA 9 $571ODP 5 1800 230/460 EE CT 4:1 Yes 184TC DP00518AEKCA 9 $573ODP 5 1200 230/460 EE CT 4:1 Yes 215TC DP00512AEKCA 9 $792ODP 7.5 3600 230/460 EE CT 4:1 Yes 184TC DP7F536AEKCA 9 $699ODP 7.5 1800 230/460 EE CT 4:1 Yes 213TC DP7F518AEKCA 9 $707ODP 7.5 1200 230/460 EE CT 2:1 Yes 254TC DP7F512AEJCA 9 $947ODP 10 3600 230/460 EE CT 4:1 Yes 213TC DP01036AEKCA 9 $795ODP 10 1800 230/460 EE CT 4:1 Yes 215TC DP01018AEKCA 9 $797ODP 10 1200 230/460 EE CT 2:1 Yes 256TC DP01012AEJCA 9 $1,082ODP 15 3600 230/460 EE CT 4:1 Yes 215TC DP01536AEKCA 9 $944ODP 15 1800 230/460 EE CT 2:1 Yes 254TC DP01518AEJCA 9 $989ODP 15 1200 230/460 EE CT 2:1 Yes 284TC DP01512AEJCA 9 $1,345ODP 20 3600 230/460 EE CT 2:1 Yes 254TC DP02036AEJCA 9 $1,084ODP 20 1800 230/460 EE CT 2:1 Yes 256TC DP02018AEJCA 9 $1,142ODP 20 1200 230/460 EE CT 2:1 Yes 286TC DP02012AEJCA 9 $1,573ODP 25 3600 230/460 EE CT 2:1 Yes 256TC DP02536AEJCA 9 $1,253ODP 25 1800 230/460 EE CT 2:1 Yes 284TC DP02518AEJCA 9 $1,315ODP 30 3600 230/460 EE CT 2:1 Yes 284TSC DP03036AEJCA 9 $1,479ODP 30 1800 230/460 EE CT 2:1 Yes 286TC DP03018AEJCA 9 $1,475



33

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es





CONNECTIONS: Final connect dual to single voltage.107 High Voltage Connection (price by frame size) All $162108 Low Voltage Connection (price by frame size) All $162







Note: Not available on L180-L210 frames 320-449 $376 SEALS: Addition of shaft seal.

148 Additon of V-ring rubber slinger on drive end All $216SPACE HEATERS:








34

General

Information

CM

100C

M 200

CM

300F

ootnotes


Component ClassInverter Duty General Purpose SeriesCM107 Family - SE/EE/PE/NP AC Motors



Frequency: 60 Hz Duty Cycle: Continuous SE = Standard efficient motors not requiring EPAct efficiencies. Ambient: 40° C Insulation: Class F

Service Factor: 1.00 Temp. Rise: Class F EE = Energy Efficient motors that meet EPAct efficiency levels.

Application InformationDesigned for all general purpose industrial applications in a clean and dry environment.

PE = Premium Efficient motors that exceed EPAct efficiency levels



SE (24 / 12), EE (24 / 12),PE (36 / 24), NP (36 / 24)Nameplate Agency Approvals:CE, CSA, UR

180T - 449T FramesMaterials: Cast iron frame and end shields, steel conduit box.Conduit Box: F1, Diagonally split, rotatable in 90 degree increments.Bearing Type: BallBearing Protection: (360 T - 449T frames) Inner capsShaft Material: High strength carbon steelNameplate Material: Stainless steel or aluminumDrain Type & Location: NoneAdditional Features: Insulation system on all EE, PE, and NP motors exceeds

NEMA MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

CM107 Family - SE/EE/PE/NP AC Motors

35

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Component Class, Inverter Duty General Purpose SeriesCM107 - Open EE/PE/NP AC Motors


RPM Class Torque/Spd Stock CM107- PriceODP 1.5 1200 230/460 NP CT 2:1 N 213T DP1F512ANJHA 35 $868ODP 2 1200 230/460 NP CT 2:1 N 213T DP00212ANJHA 35 $977ODP 3 3600 230/460 NP CT 2:1 N 182T DP00336ANJHA 35 $729ODP 3 1800 230/460 NP CT 2:1 Yes 182T DP00318ANJHA $633ODP 3 1200 230/460 NP CT 2:1 N 213T DP00312ANJHA $1,169ODP 5 3600 230/460 NP CT 2:1 Yes 182T DP00536ANJHA 9 $729ODP 5 1800 230/460 NP CT 2:1 N 213T DP00518ANJHA 35 $888ODP 5 1200 230/460 NP CT 2:1 N 215T DP00512ANJHA $1,490ODP 5 900 460 PE CT 2:1 N 254T DP00509BPJHA $1,819ODP 7.5 3600 230/460 NP CT 2:1 Yes 184T DP7F536ANJHA 9 $965ODP 7.5 1800 230/460 NP CT 2:1 N 184T DP7F518ANJHA $965ODP 7.5 1200 230/460 NP CT 2:1 N 254T DP7F512ANJHA $2,450ODP 7.5 900 460 PE CT 2:1 N 256T DP7F509BPJHA $2,259ODP 10 3600 230/460 NP CT 2:1 Yes 213T DP01036ANJHA 75 $1,020ODP 10 1800 230/460 NP CT 2:1 N 254T DP01018ANJHA 35 $1,313ODP 10 1200 230/460 NP CT 2:1 N 256T DP01012ANJHA $2,667ODP 15 3600 230/460 NP CT 2:1 Yes 215T DP01536ANJHA 9 $1,423ODP 15 1800 230/460 NP CT 2:1 N 256T DP01518ANJHA $1,493ODP 15 1200 230/460 NP CT 2:1 N 286T DP01512ANJHA $2,748ODP 15 900 460 PE CT 2:1 N 286T DP01509BPJHA $3,405ODP 20 3600 230/460 NP CT 2:1 Yes 254T DP02036ANJHA 9 $1,691ODP 20 1800 230/460 NP CT 2:1 Yes 256T DP02018ANJHA 9 $1,556ODP 20 1800 230/460 PE CT 2:1 Yes 256T DP02018APJHA 75 $1,556ODP 20 1200 230/460 NP CT 2:1 N 286T DP02012ANJHA $2,822ODP 20 900 460 PE CT 2:1 N 324T DP02009BPJHA $4,163ODP 25 3600 230/460 NP CT 2:1 Yes 256T DP02536ANJHA 9 $1,932ODP 25 1800 230/460 NP CT 2:1 N 284T DP02518ANJHA $1,775ODP 25 1200 230/460 NP CT 2:1 N 326T DP02512ANJHA $2,998ODP 25 1200 230/460 EE CT 2:1 Yes 324T DP02512AEJHA 9 $2,192ODP 25 900 460 PE CT 2:1 N 326T DP02509BPJHA $4,875ODP 30 3600 230/460 NP CT 2:1 Yes 284TS DP03036ANJHA 9 $1,790ODP 30 1800 230/460 NP CT 2:1 N 286T DP03018ANJHA 35 $2,029ODP 30 1200 230/460 EE CT 2:1 N 326T DP03012AEJHA 9 $2,462ODP 30 1200 230/460 NP CT 2:1 N 326T DP03012ANJHA $3,107ODP 30 900 460 PE CT 2:1 N 364T DP03009BPJHA $5,487ODP 40 3600 230/460 NP CT 2:1 N 286TS DP04036ANJHA $2,809ODP 40 1800 230/460 NP CT 2:1 Yes 324T DP04018ANJHA 9 $2,578ODP 40 1200 230/460 EE CT 2:1 N 364T DP04012AEJHA $3,844ODP 40 1200 230/460 NP CT 2:1 N 365T DP04012ANJHA $5,110ODP 40 900 460 PE CT 2:1 N 365T DP04009BPJHA $6,720ODP 50 3600 230/460 NP CT 2:1 N 324TS DP05036ANJHA $3,403ODP 50 1775 230/460 PE CT 2:1 0 326T DP05017APJHA $2,903ODP 50 1800 230/460 NP CT 2:1 Yes 326T DP05018ANJHA 9 $2,953ODP 50 1200 230/460 EE CT 2:1 N 365T DP05012AEJHA $4,439ODP 50 1200 230/460 NP CT 2:1 N 365T DP05012ANJHA $5,110ODP 50 900 460 PE CT 2:1 N 404T DP05009BPJHA $7,949ODP 60 3600 230/460 NP CT 2:1 N 326TS DP06036ANJHA $3,872ODP 60 1800 230/460 NP CT 2:1 Yes 364T DP06018ANJHA 9 $3,507ODP 60 1200 460 EE CT 2:1 N 404T DP06012BEJHA $5,127ODP 60 1200 230/460 NP CT 2:1 Yes 404T DP06012ANJHA $5,911ODP 60 900 460 PE CT 2:1 N 405T DP06009BPJHA $9,165ODP 75 3600 230/460 NP CT 2:1 N 364TS DP07536ANJHA $4,998ODP 75 1800 230/460 NP CT 2:1 Yes 365T DP07518ANJHA 9 $4,254ODP 75 1200 460 EE CT 2:1 N 405T DP07512BEJHA $6,045ODP 75 1200 230/460 NP CT 2:1 Yes 405T DP07512ANJHA $6,978ODP 75 900 460 PE CT 2:1 N 444T DP07509BPJHA $10,917ODP 100 3600 230/460 NP CT 2:1 N 365TS DP10036ANJHA $6,131


36

General

Information

CM

100C

M 200

CM

300F

ootnotes


ODP 100 1800 230/460 NP CT 2:1 Yes 404T DP10018ANJHA 75 $5,338ODP 100 1200 460 EE CT 2:1 N 444T DP10012BEJHA $7,574ODP 100 1200 230/460 NP CT 2:1 Yes 444T DP10012ANJHA $8,755ODP 125 3600 460 NP CT 2:1 N 404TS DP12536BNJHA $7,553ODP 125 1800 460 NP CT 2:1 Yes 405T DP12518BNJHA 9 $6,331ODP 125 1200 460 EE CT 2:1 N 445T DP12512BEJHA $9,230ODP 125 1200 460 NP CT 2:1 Yes 445T DP12512BNJHA $10,681ODP 150 3600 460 NP CT 2:1 N 405TS DP15036BNJHA $9,120ODP 150 1800 460 NP CT 2:1 N 444T DP15018BNJHA $9,005ODP 150 1200 460 EE CT 2:1 N 445T DP15012BEJUA 5 $10,198ODP 150 1200 460 NP CT 2:1 Yes 445T DP15012BNJHA $11,806ODP 200 3600 460 EE CT 2:1 N 444TS DP20036BEJHA 4 $12,127ODP 200 3600 460 NP CT 2:1 Yes 444TS DP20036BNJHA $14,013ODP 200 1800 460 EE CT 2:1 N 445TS DP20018BEJHSA 4 $8,695ODP 200 1800 460 NP CT 2:1 Yes 445T DP20018BNJHA $11,294ODP 200 1800 460 EE CT 2:1 N 445T DP20018BEJHTA $8,695ODP 200 1200 460 EE CT 2:1 N 445T DP20012BEJUA 4,5 $13,277ODP 200 1200 460 NP CT 2:1 Yes 447T DP20012BNJHA $14,785ODP 250 3600 460 EE CT 2:1 N 445TS DP25036BEJHA 4 $14,235ODP 250 3600 460 NP CT 2:1 Yes 445TS DP25036BNJHA $16,693ODP 250 1800 460 EE CT 2:1 N 445TS DP25018BEJHA 4 $10,759ODP 250 1800 460 NP CT 2:1 Yes 447T DP25018BNJHA $16,973ODP 250 1200 460 EE CT 2:1 N 447T DP25012BEJUA 4,5 $18,159ODP 250 1200 460 NP CT 2:1 Yes 449T DP25012BNJHA $20,395ODP 300 3600 460 EE CT 2:1 N 445TS DP30036BEJHA 4 $18,124ODP 300 3600 460 NP CT 2:1 Yes 445TS DP30036BNJHA $21,636ODP 300 1800 460 EE CT 2:1 N 445TS DP30018BEJHA 4 $13,844ODP 300 1800 460 NP CT 2:1 Yes 449T DP30018BNJHA $17,796ODP 300 1200 460 NP CT 2:1 N 449T DP30012BNJHA 2,20 $24,219ODP 350 3600 460 EE CT 2:1 N 445TS DP35036BEJHA 4 $19,561ODP 350 3600 460 NP CT 2:1 Yes 447TS DP35036BNJHA $24,074ODP 350 1800 460 EE CT 2:1 N 447TS DP35018BEJHA 4 $16,758ODP 350 1800 460 NP CT 2:1 Yes 449T DP35018BNJHA $20,678ODP 400 3600 460 EE CT 2:1 N 447TS DP40036BEJHA 4 $22,610ODP 400 3600 460 NP CT 2:1 Yes 449TS DP40036BNJHA $27,896ODP 400 1800 460 EE CT 2:1 N 449TS DP40018BEJHA 4,6 $18,148ODP 400 1800 460 NP CT 2:1 Yes 449T DP40018BNJHA $25,333ODP 450 3600 460 EE CT 2:1 N 447TS DP45036BEJHA 4 $24,452ODP 450 3600 460 NP CT 2:1 Yes 449TS DP45036BNJHA $30,300ODP 450 1800 460 NP CT 2:1 N 449TS DP45018BNJHA 4,6 $30,274ODP 500 3600 460 NP CT 2:1 N 449TS DP50036BNJHA 4 $33,193



37

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es





















38

General

Information

CM

100C

M 200

CM

300F

ootnotes


Component ClassInverter Duty Harsh Environment SeriesCM111 Family - Severe Duty AC Motors



Frequency: 60 Hz Duty Cycle: Continuous SE = Standard efficient motors not requiring EPAct efficiencies.Ambient: 40° C Insulation: Class F

Service Factor: 1.00 Temp. Rise: Class F EE = Energy Efficient motors that meet EPAct efficiency levels.PE = Premium Efficient motors that exceed EPAct efficiency levels.Application Information

Severe Duty motors are built with rugged cast iron construction and key features for long life in moist, contaminated environments such as chemical plants, petroleum refineries and paper mills.

NP = NEMA Premium efficient motors.Warranty (From Date Of Manufacture / From Date Of Installation):

SE (24 / 12), EE (24 / 12),PE (36 / 24), NP (36 / 24)Nameplate Agency Approvals:CE, CSA, UR, IEEE45 / ABS (10)

56 - 140T FramesMaterials: (SE & EE) - Plated steel frame, conduit box and fan

shroud, cast iron end shields(PE & NP) - Cast iron frame, conduit box, fan shroud, and end shields

Conduit Box: Oversized, top mounted with F1 & F2 lead outlets. Cast iron frames have F1 location.

Bearing Type: (SE & EE) - Double sealed, permanently lubricated ball bearings(PE & NP) - Double shielded, regreasable ball bearings with grease relief fittings

Bearing Protection: (SE & EE) - Lip seals on both ends of the motor(PE & NP) - Non-metallic V-ring shaft and slinger on drive end

Shaft Material: 400 Series Stainless Steel shaftNameplate Material: (SE & EE) - Adhesive Mylar; (PE & NP) - Stainless SteelDrain Type & Location: T-drain in drive end shield. Weep hole in opposite drive end

shield. Fan cooled. TENV has T-drain both ends for SE & EE.

Additional Features: Insulation system on all EE, PE and NP motors exceeds NEMA MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

180T - 449T FramesMaterials: Cast iron construction: frame, conduit box, fan cover, end shields and inner capsConduit Box: F1 location, Diagonally split, neoprene gasketed, rotatable in 90 degree increments and NPF threaded lead

hole. UL listed clamp type grounding lug in box.Bearing Type: Regreasable, open ball bearings with PLS (180T - 449T frames).Bearing Protection: Non-metallic V-ring shaft slinger on drive endShaft Material: High strength carbon steelNameplate Material: Stainless SteelDrain Type & Location: Stainless steel T-drains mounted in both end shieldsAdditional Features: The motor stator and rotor are completely epoxy coated for corrosion protection.

Severe duty motors are provided with alemite grease fittings for easy bearing maintenanceSilicone rubber sealed fits provide superior protection against contaminates entering the motor bodyInsulation system on all EE, PE and NP motors exceeds NEMA MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

CM111 Family - Severe Duty AC Motors

39

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Component Class, Inverter Duty Harsh Environment SeriesCM111 Family - Severe Duty AC Motors


RPM Class Torque/Spd Stock CM111- PriceTENV 0.33 1800 208-230/460 SE CT 4:1 Yes 56 NVF3318GSKHA 15 $528TENV 0.33 1800 230/460 EE CT 10:1 Yes 56 NVF3318AEHHA $544TENV 0.33 1200 230/460 EE CT 10:1 N 56 NVF3312AEHHA $653TENV 0.5 3600 230/460 SE CT 4:1 N 56 NV0F536ASKHA $556TENV 0.5 3600 230/460 EE CT 10:1 N 56 NV0F536AEHHA $566TEFC 0.5 1800 208-230/460 SE CT 4:1 Yes 56 FC0F518GSKHA 15 $558TENV 0.5 1800 230/460 EE CT 10:1 Yes 56 NV0F518AEHHA $577TENV 0.5 1800 230/460 PE CT 1000:1 N 143T NV0F518APZHA 50 $835TENV 0.5 1200 230/460 EE CT 10:1 N 56 NV0F512AEHHA $696TENV 0.5 1200 230/460 PE CT 1000:1 N 143T NV0F512APZHA 50 $985TEFC 0.75 3600 208-230/460 SE CT 4:1 Yes 56 FCF7536GSKHA 15 $583TENV 0.75 3600 230/460 EE CT 10:1 N 56 NVF7536AEHHA $590TEFC 0.75 1800 208-230/460 SE CT 4:1 Yes 56 FCF7518GSKHA 15 $584TENV 0.75 1800 230/460 EE CT 10:1 Yes 56 NVF7518AEHHA $606TENV 0.75 1800 230/460 PE CT 10:1 N 143T NVF7518APHHA 50 $875TEFC 0.75 1200 208-230/460 SE CT 10:1 N 143T FCF7512GSHHA 15 $702TENV 0.75 1200 230/460 EE CT 10:1 N 56 NVF7512AEHHA $708TEFC 0.75 1200 230/460 EE CT 4:1 N 143T FCF7512AEKHA $708TENV 0.75 1200 230/460 PE CT 1000:1 Yes 143T NVF7512APZHA 50 $1,001TEFC 1 3600 208-230/460 SE CT 1000:1 N 56 FC00136GSZHA 15 $616TENV 1 3600 230/460 EE CT 4:1 N 56 NV00136AEKHA $624TENV 1 3600 230/460 NP CT 10:1 Yes 143T NV00136ANHHA 50 $868TENV 1 1800 230/460 SE CT 4:1 Yes 56 NV00118ASKHA $591TEFC 1 1800 230/460 EE CT 4:1 N 56 FC00118AEKH5A $613TEFC 1 1800 230/460 EE CT 4:1 Yes 143T FC00118AEKH4A $613TENV 1 1800 230/460 NP CT 1000:1 Yes 143T NV00118ANZHA 50 $884TEFC 1 1200 230/460 EE CT 4:1 N 56 FC00112AEKH5A $724TEFC 1 1200 230/460 EE CT 4:1 Yes 145T FC00112AEKH4A $724TEFC 1 1200 230/460 NP CT 20:1 Yes 145T FC00112ANMHA 50 $1,041TEFC 1 900 460 PE CT 10:1 Yes L182T FC00109BPHHA $1,061TEFC 1.5 3600 208-230/460 SE CT 4:1 Yes 56 FC1F536GSKHA 15 $676TEFC 1.5 3600 230/460 EE CT 4:1 N 56 FC1F536AEKH5A $680TEFC 1.5 3600 230/460 EE CT 4:1 N 143T FC1F536AEKH4A $680TEFC 1.5 3600 230/460 NP CT 20:1 Yes 143T FC1F536ANMHA 50 $953TEFC 1.5 1800 208-230/460 SE CT 4:1 N 56 FC1F518GSKHA $619TEFC 1.5 1800 230/460 EE CT 4:1 N 56 FC1F518AEKH5A $629TEFC 1.5 1800 230/460 EE CT 4:1 Yes 145T FC1F518AEKH4A $629TEFC 1.5 1800 230/460 NP CT 20:1 Yes 145T FC1F518ANMHA 50 $927TEFC 1.5 1200 230/460 NP CT 10:1 Yes L182T FC1F512ANHHA $838TEFC 1.5 1200 460 PE CT 10:1 Yes 182T FC1F512BPHHA $838TEFC 1.5 900 460 PE CT 10:1 Yes L184T FC1F509BPHHA $1,216TEFC 2 3600 230/460 SE CT 4:1 N 56 FC00236ASKHA $734TEFC 2 3600 230/460 EE CT 4:1 N 56 FC00236AEKH5A $747TEFC 2 3600 230/460 EE CT 4:1 Yes 145T FC00236AEKH4A $747TEFC 2 3600 230/460 NP CT 20:1 Yes 145T FC00236ANMHA 50 $1,033TEFC 2 1800 230/460 SE CT 4:1 N 56 FC00218ASKHA $647TEFC 2 1800 230/460 EE CT 4:1 N 56 FC00218AEKH5A $591TEFC 2 1800 230/460 EE CT 4:1 Yes 145T FC00218AEKH4A $664TEFC 2 1800 230/460 NP CT 20:1 Yes 145 FC00218ANMHA 50 $971TEFC 2 1200 230/460 NP CT 10:1 Yes L184T FC00212ANHHA $911TEFC 2 1200 460 PE CT 10:1 Yes L184T FC00212BPHHA $911TEFC 2 900 460 PE CT 10:1 Yes L213T FC00209BPHHA $1,411


40

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 3 3600 230/460 EE VT 10:1 (2) N 182T FC00336AEVHA $752TEFC 3 3600 460 PE CT 10:1 Yes 182T FC00336BPHHA $833TEFC 3 3600 230/460 NP CT 10:1 Yes 182T FC00336ANHHA $833TEFC 3 1800 230/460 NP CT 10:1 Yes L182T FC00318ANHHA $816TEFC 3 1800 460 PE CT 10:1 Yes 182T FC00318BPHHA $816TEFC 3 1200 460 PE CT 10:1 Yes 213T FC00312BPHHA $1,063TEFC 3 1200 230/460 NP CT 10:1 Yes 213T FC00312ANHHA $1,063TEFC 3 900 460 PE CT 10:1 Yes L215T FC00309BPHHA $1,711TEFC 5 3600 230/460 NP CT 10:1 Yes 184T FC00536ANHHA $950TEFC 5 3600 460 PE CT 10:1 Yes 184T FC00536BPHHA $950TEFC 5 1800 230/460 NP CT 10:1 Yes L184T FC00518ANHHA 35 $921TEFC 5 1800 460 PE CT 10:1 Yes L184T FC00518BPHHA $921TEFC 5 1200 460 PE CT 10:1 Yes L215T FC00512BPHHA $1,422TEFC 5 1200 230/460 NP CT 10:1 Yes L215T FC00512ANHHA $1,422TEFC 5 900 460 PE CT 4:1 (10) Yes 254T FC00509BPKHA $2,205TEFC 7.5 3600 230/460 NP CT 10:1 Yes 213T FC7F536ANHHA $1,177TEFC 7.5 3600 460 PE CT 10:1 Yes 213T FC7F536BPHHA $1,177TEFC 7.5 1800 460 PE CT 10:1 Yes 213T FC7F518BPHHA $1,171TEFC 7.5 1800 230/460 NP CT 10:1 Yes L213T FC7F518ANHHA $1,171TEFC 7.5 1200 460 PE CT 4:1 (10) Yes 254T FC7F512BPKHA $1,820TEFC 7.5 1200 230/460 NP CT 4:1 Yes 254T FC7F512ANKHA $1,820TEFC 7.5 900 460 PE CT 4:1 (10) Yes 256T FC7F509BPKHA $2,732TEFC 10 3600 460 PE CT 10:1 Yes 215T FC01036BPHHA $1,344TEFC 10 3600 230/460 NP CT 10:1 Yes 215T FC01036ANHHA $1,344TEFC 10 1800 460 PE CT 10:1 Yes L215T FC01018BPHHA $1,282TEFC 10 1800 230/460 NP CT 10:1 Yes L215T FC01018ANHHA $1,282TEFC 10 1200 460 PE CT 4:1 (10) Yes 256T FC01012BPKHA $2,185TEFC 10 1200 230/460 NP CT 4:1 (10) Yes 256T FC01012ANKHA $2,185TEFC 10 900 460 PE CT 4:1 (10) Yes 284T FC01009BPKHA $3,154TEFC 15 3600 460 PE CT 4:1 (10) Yes 254T FC01536BPKHA $1,767TEFC 15 3600 230/460 NP CT 4:1 (10) Yes 254T FC01536ANKHA $1,767TEFC 15 1800 230/460 NP CT 4:1 (10) Yes 254T FC01518ANKHA $1,685TEFC 15 1800 460 PE CT 4:1 (10) Yes 254T FC01518BPKHA $1,685TEFC 15 1200 460 PE CT 4:1 (10) Yes 284T FC01512BPKHA $2,839TEFC 15 1200 230/460 NP CT 4:1 (10) Yes 284T FC01512ANKHA $2,839TEFC 15 900 460 PE CT 4:1 (10) Yes 286T FC01509BPKHA $4,046TEFC 20 3600 460 PE CT 4:1 (10) Yes 256T FC02036BPKHA $2,084TEFC 20 3600 230/460 NP CT 4:1 (10) Yes 256T FC02036ANKHA $2,084TEFC 20 1800 230/460 NP CT 4:1 Yes 256T FC02018ANKHA $1,973TEFC 20 1800 460 PE CT 4:1 (10) Yes 256T FC02018BPKHA $1,973TEFC 20 1200 460 PE CT 4:1 (10) Yes 286T FC02012BPKHA $3,472TEFC 20 1200 230/460 NP CT 4:1 (10) Yes 286T FC02012ANKHA $3,472TEFC 20 900 460 PE CT 4:1 (10) Yes 324T FC02009BPKHA $4,900TEFC 25 3600 460 PE CT 4:1 (10) Yes 284TS FC02536BPKHA $2,558TEFC 25 3600 230/460 NP CT 4:1 (10) Yes 284TS FC02536ANKHA $2,558TEFC 25 1800 230/460 NP CT 4:1 (10) Yes 284T FC02518ANKHA $2,460TEFC 25 1800 460 PE CT 4:1 (10) Yes 284T FC02518BPKHA $2,460TEFC 25 1200 230/460 NP CT 4:1 (10) Yes 324T FC02512ANKHA $4,133TEFC 25 1200 460 PE CT 4:1 (10) Yes 324T FC02512BPKHA $4,133TEFC 30 3600 460 PE CT 4:1 (10) Yes 286TS FC03036BPKHA $2,972TEFC 30 3600 230/460 NP CT 4:1 (10) Yes 286TS FC03036ANKHA $2,972TEFC 30 1800 460 PE CT 4:1 (10) Yes 286T FC03018BPKHA $2,839TEFC 30 1800 230/460 NP CT 4:1 (10) Yes 286T FC03018ANKHA $2,839TEFC 30 1200 230/460 NP CT 4:1 (10) Yes 326T FC03012ANKHA $4,671TEFC 30 1200 460 PE CT 4:1 (10) Yes 326T FC03012BPKHA $4,671


41

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 40 3600 230/460 EE VT 10:1 (2) Yes 324TS FC04036AEVHA $3,302TEFC 40 3600 230/460 NP CT 4:1 (10) Yes 324TS FC04036ANKHA $3,751TEFC 40 3600 460 PE CT 4:1 (10) Yes 324TS FC04036BPKHA $3,751TEFC 40 1800 230/460 NP CT 4:1 (10) Yes 324T FC04018ANKHA $3,721TEFC 40 1800 460 PE CT 4:1 (10) Yes 324T FC04018BPKHA $3,721TEFC 40 1200 230/460 PE CT 4:1 (10) N 364T FC04012APKHA $6,324TEFC 40 1200 460 NP CT 4:1 (10) Yes 364T FC04012BNKHA $6,324TEFC 50 3600 460 PE CT 4:1 (10) Yes 326TS FC05036BPKHA $4,711TEFC 50 3600 230/460 PE CT 4:1 (10) Yes 326TS FC05036APKHA $4,711TEFC 50 1800 230/460 EE VT 10:1 (2) Yes 326T FC05018AEVHA $3,785TEFC 50 1800 460 PE CT 4:1 (10) Yes 326T FC05018BPKHA $4,308TEFC 50 1800 230/460 NP CT 4:1 (10) Yes 326T FC05018ANKHA $4,308TEFC 50 1800 460 PE CT 4:1 (10) N 326TS FC05018BPKHA $4,308TEFC 50 1200 230/460 EE VT 10:1 (2) Yes 365T FC05012AEVHA $6,379TEFC 50 1200 460 NP CT 4:1 (10) Yes 365T FC05012BNKHA $7,292TEFC 50 1200 230/460 PE CT 4:1 (10) N 365T FC05012APKHA $7,292TEFC 60 3600 230/460 EE VT 10:1 (2) Yes 364TS FC06036AEVHA $5,637TEFC 60 3600 230/460 PE CT 4:1 (10) N 364TS FC06036APKHA $6,434TEFC 60 3600 460 NP CT 4:1 (10) Yes 364TS FC06036BNKHA $6,434TEFC 60 1800 230/460 EE VT 10:1 (2) Yes 364T FC06018AEVHA $5,528TEFC 60 1800 230/460 PE CT 4:1 (10) N 364T FC06018APKHA $6,307TEFC 60 1800 460 PE CT 4:1 (10) N 364TS FC06018BPKHA $6,307TEFC 60 1800 460 NP CT 4:1 (10) Yes 364T FC06018BNKHA $6,307TEFC 60 1200 230/460 EE VT 10:1 (2) Yes 404T FC06012AEVHA $7,374TEFC 60 1200 230/460 PE CT 4:1 (10) N 404T FC06012APKHA $8,431TEFC 60 1200 460 NP CT 4:1 (10) Yes 404T FC06012BNKHA $8,431TEFC 75 3600 230/460 EE VT 10:1 (2) Yes 365TS FC07536AEVHA $6,843TEFC 75 3600 230/460 PE CT 4:1 (10) N 365TS FC07536APKHA $7,828TEFC 75 3600 460 NP CT 4:1 (10) Yes 365TS FC07536BNKHA $7,828TEFC 75 1800 230/460 EE VT 10:1 (2) Yes 365T FC07518AEVHA $6,628TEFC 75 1800 230/460 NP CT 4:1 Yes 365T FC07518ANKHA $7,580TEFC 75 1800 460 PE CT 4:1 (10) N 365TS FC07518BPKHSA $7,580TEFC 75 1800 460 PE CT 4:1 (10) Yes 365T FC07518BPKHTA $7,580TEFC 75 1200 230/460 EE CT 4:1 (10) Yes 405T FC07512AEKHA $8,158TEFC 75 1200 230/460 PE VT 10:1 (2) N 405T FC07512APVHA $9,338TEFC 75 1200 460 NP CT 4:1 (10) Yes 405T FC07512BNKHA $9,338TEFC 100 3600 230/460 PE CT 4:1 (10) N 405TS FC10036APKHA $10,044TEFC 100 3600 460 NP CT 4:1 (10) Yes 405TS FC10036BNKHA $10,044TEFC 100 1800 230/460 EE VT 10:1 (2) Yes 405T FC10018AEVHA $8,115TEFC 100 1800 230/460 PE CT 4:1 (10) N 405T FC10018APKHA $9,289TEFC 100 1800 460 NP CT 4:1 (10) Yes 405T FC10018BNKHA $9,289TEFC 100 1800 460 PE CT 4:1 (10) N 405TS FC10018BPKHA $9,289TEFC 100 1200 230/460 EE VT 10:1 (2) Yes 444T FC10012AEVHA $10,884TEFC 100 1200 460 NP CT 4:1 (10) Yes 444T FC10012BNKHA $12,468TEFC 125 3600 460 NP CT 4:1 (10) Yes 444TS FC12536BNKHA $13,024TEFC 125 1800 460 EE VT 10:1 (2) Yes 444T FC12518BEVHA $10,585TEFC 125 1800 460 NP CT 4:1 (10) Yes 444T FC12518BNKHA $12,122TEFC 125 1800 460 PE CT 4:1 (10) N 444TS FC12518BPKHA $12,122TEFC 125 1200 460 EE VT 10:1 (2) Yes 445T FC12512BEVHA $13,036TEFC 125 1200 460 NP CT 4:1 (10) Yes 445T FC12512BNKHA $14,955TEFC 150 3600 460 NP CT 4:1 (10) Yes 445TS FC15036BNKHA $15,598TEFC 150 1800 460 EE VT 10:1 (2) Yes 445T FC15018BEVHA $12,254TEFC 150 1800 460 NP CT 4:1 (10) Yes 445T FC15018BNKHA $14,052TEFC 150 1800 460 PE CT 4:1 (10) N 445TS FC15018BPKHA $14,052TEFC 150 1200 460 EE VT 10:1 (2) Yes 445T FC15012BEVUA 5 $14,713TEFC 150 1200 460 NP CT 2:1 (10) Yes 447T FC15012BNJUA 5 $18,052


42

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 200 3600 460 EE VT 10:1 (2) Yes 445TS FC20036BEVHA 4 $17,108TEFC 200 3600 460 NP CT 4:1 (10) Yes 445TS FC20036BNKHA $19,664TEFC 200 1800 460 EE VT 10:1 (2) Yes 445T FC20018BEVUA 4,5 $14,785TEFC 200 1800 460 NP CT 2:1 (10) Yes 447T FC20018BNJUA 5 $17,547TEFC 200 1800 460 PE CT 2:1 (10) Yes 447TS FC20018BPJHA $17,547TEFC 200 1200 460 EE VT 10:1 Yes 447T FC20012BEVUA 4,5 $18,167TEFC 200 1200 460 NP CT 2:1 (10) Yes 449T FC20012BNJUA 5 $20,159TEFC 250 3600 460 EE VT 10:1 Yes 447TS FC25036BEVHA 4 $22,566TEFC 250 3600 460 NP CT 2:1 (10) Yes 447TS FC25036BNJHA $25,245TEFC 250 1800 460 SE VT 10:1 Yes 447TS FC25018BSVUA 5,75 $19,190TEFC 250 1800 460 EE VT 10:1 Yes 447TS FC25018BEVHB 4,75 $18,432TEFC 250 1800 460 EE VT 10:1 Yes 447T FC25018BEVUA 4,5 $18,432TEFC 250 1800 460 PE CT 2:1 (10) Yes 449TS FC25018BPJHA $20,466TEFC 250 1800 460 NP CT 2:1 (10) Yes 449T FC25018BNJUA 5 $20,466TEFC 250 1200 460 EE VT 10:1 Yes 449T FC25012BEVUA 4,5 $23,068TEFC 250 1200 460 NP CT 2:1 (10) Yes 449T FC25012BNJUA 5 $25,940TEFC 300 3600 460 NP CT 2:1 (10) Yes 449TS FC30036BNJHA 35 $31,230TEFC 300 1800 460 EE CT 2:1 (10) Yes 449TS FC30018BEJHA 4 $21,411TEFC 300 1800 460 PE CT 2:1 (10) Yes 449TS FC30018BPJHA $23,910TEFC 300 1800 460 NP CT 2:1 (10) Yes 449T FC30018BNJUA 5 $23,910TEFC 350 3600 460 NP CT 2:1 (10) Yes 449TS FC35036BNJHA $35,177TEFC 350 1800 460 NP CT 2:1 (10) Yes 449T FC35018BNJUA 5 $27,770TEFC 400 3600 460 PE CT 2:1 (10) Yes 449TS FC40036BPJHA $38,631


C Face Foot Mounted IP54Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Catalog String Notes US List

RPM Class Torque/Spd Stock CM111- PriceTENV 0.25 1800 208-230/460 SE CT 4:1 Yes 56C NVF2518GSKCA 15 $565TENV 0.33 1800 208-230/460 SE CT 4:1 N 56C NVF3318GSKCA 15 $574TENV 0.33 1800 230/460 EE CT 10:1 N 56C NVF3318AEHCA $580TENV 0.33 1200 208-230/460 SE CT 4:1 N 56C NVF3312GSKCA 15 $690TENV 0.33 1200 230/460 EE CT 10:1 N 56C NVF3312AEHCA $703TENV 0.5 3600 208-230/460 SE CT 4:1 Yes 56C NV0F536GSKCA 15 $563TENV 0.5 3600 230/460 EE CT 10:1 N 56C NV0F536AEHCA $571TEFC 0.5 1800 208-230/460 SE CT 4:1 Yes 56C FC0F518GSKCA 15 $607TENV 0.5 1800 230/460 EE CT 10:1 N 56C NV0F518AEHCA $615TENV 0.5 1800 230/460 PE CT 1000:1 N 143TC NV0F518APZCA 50 $880TEFC 0.5 1200 208-230/460 SE CT 4:1 Yes 56C FC0F512GSKCA 15 $723TENV 0.5 1200 230/460 EE CT 10:1 N 56C NV0F512AEHCA $732TENV 0.5 1200 230/460 PE CT 1000:1 N 143TC NV0F512APZCA 50 $1,038TEFC 0.75 3600 208-230/460 SE CT 4:1 Yes 56C FCF7536GSKCA 15 $589TENV 0.75 3600 230/460 EE CT 10:1 N 56C NVF7536AEHCA $600TEFC 0.75 1800 208-230/460 SE CT 4:1 Yes 56C FCF7518GSKCA 15 $635TENV 0.75 1800 230/460 EE CT 10:1 N 56C NVF7518AEHCA $649TENV 0.75 1800 230/460 PE CT 1000:1 N 143TC NVF7518APZCA 50 $922TEFC 0.75 1200 208-230/460 SE CT 4:1 Yes 56C FCF7512GSKCA 15 $736TENV 0.75 1200 230/460 EE CT 10:1 N 56C NVF7512AEHCA $747TEFC 0.75 1200 230/460 EE CT 4:1 N 143TC FCF7512AEKCA $747TENV 0.75 1200 230/460 PE CT 1000:1 N 143TC NVF7512APZCA 50 $1,054


43

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 1 3600 208-230/460 SE CT 4:1 Yes 56C FC00136GSKCA 15 $621TEFC 1 3600 230/460 EE CT 4:1 N 56C FC00136AEKCA $629TENV 1 3600 230/460 PE CT 1000:1 Yes 143TC NV00136APZCA 50 $915TENV 1 1800 208-230/460 SE CT 4:1 Yes 56C NV00118GSKCA 15 $642TEFC 1 1800 230/460 EE CT 4:1 N 56C FC00118AEKC5A $654TEFC 1 1800 230/460 EE CT 4:1 N 143TC FC00118AEKC4A $654TENV 1 1800 230/460 PE CT 1000:1 Yes 143TC NV00118APZCA 50 $922TEFC 1 1200 208-230/460 SE CT 4:1 Yes 56C FC00112GSKCA 15 $765TEFC 1 1200 230/460 EE CT 4:1 N 56C FC00112AEKC5A $776TEFC 1 1200 230/460 EE CT 4:1 N 145TC FC00112AEKC4A $776TEFC 1 1200 230/460 PE CT 20:1 N 145TC FC00112APMCA 50 $1,095TEFC 1.5 3600 208-230/460 SE CT 4:1 Yes 56C FC1F536GSKCA 15 $679TEFC 1.5 3600 230/460 EE CT 4:1 N 56C FC1F536AEKC5A $688TEFC 1.5 3600 230/460 EE CT 4:1 N 143TC FC1F536AEKC4A $688TEFC 1.5 3600 230/460 PE CT 20:1 Yes 143TC FC1F536APMCA 50 $1,003TEFC 1.5 1800 208-230/460 SE CT 4:1 Yes 56C FC1F518GSKCA 15 $673TEFC 1.5 1800 230/460 EE CT 4:1 N 56C FC1F518AEKC5A $683TEFC 1.5 1800 230/460 EE CT 4:1 N 145TC FC1F518AEKC4A $683TEFC 1.5 1800 230/460 PE CT 20:1 Yes 145TC FC1F518APMCA 50 $978TEFC 1.5 1200 230/460 PE CT 10:1 N 182TC FC1F512APHCA $920TEFC 2 3600 230/460 EE CT 4:1 N 56C FC00236AEKC5A $740TEFC 2 3600 230/460 EE CT 4:1 N 145TC FC00236AEKC4A $740TEFC 2 3600 230/460 PE CT 20:1 Yes 145TC FC00236APMCA 50 $1,087TEFC 2 1800 230/460 EE CT 4:1 N 56C FC00218AEKC5A $670TEFC 2 1800 230/460 EE CT 4:1 N 145TC FC00218AEKC4A $670TEFC 2 1800 230/460 PE CT 20:1 Yes 145TC FC00218APMCA 50 $1,023TEFC 2 1200 230/460 PE CT 10:1 N L184TC FC00212APHCA $995TEFC 3 3600 230/460 PE CT 10:1 Yes 182TC FC00336APHCA $916TEFC 3 1800 230/460 PE CT 10:1 Yes 182TC FC00318APHCA $899TEFC 3 1200 230/460 PE CT 10:1 N 213TC FC00312APHCA $1,146TEFC 5 3600 230/460 PE CT 10:1 Yes 184TC FC00536APHCA $1,033TEFC 5 1800 230/460 PE CT 10:1 Yes L184TC FC00518APHCA $1,004TEFC 5 1200 230/460 PE CT 10:1 N L215TC FC00512APHCA $1,504TEFC 7.5 3600 230/460 PE CT 10:1 Yes 213TC FC7F536APHCA $1,260TEFC 7.5 1800 230/460 PE CT 10:1 Yes 213TC FC7F518APHCA $1,254TEFC 10 3600 230/460 PE CT 10:1 Yes 215TC FC01036APHCA $1,427TEFC 10 1800 230/460 PE CT 10:1 Yes L215TC FC01018APHCA $1,366TEFC 15 1800 460 PE CT 4:1 (10) Yes 254TC FC01518BPKCA $1,794TEFC 15 1800 230/460 PE CT 4:1 (10) Yes 254TC FC01518APKCA $1,794TEFC 20 1800 230/460 PE CT 4:1 (10) Yes 256TC FC02018APKCA $2,081TEFC 20 1800 460 PE CT 4:1 (10) Yes 256TC FC02018BPKCA $2,081TEFC 25 1800 460 PE CT 4:1 (10) Yes 284TC FC02518BPKCA $2,614TEFC 25 1800 230/460 PE CT 4:1 (10) Yes 284TC FC02518APKCA $2,614TEFC 30 1800 230/460 PE CT 4:1 (10) Yes 286TC FC03018APKCA $2,991TEFC 30 1800 460 PE CT 4:1 (10) Yes 286TC FC03018BPKCA $2,991TEFC 40 1800 230/460 PE CT 4:1 (10) Yes 324TC FC04018APKCA $3,957


C Face Footless IP54Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Catalog String Notes US List

RPM Class Torque/Spd Stock CM111- PriceTENV 0.33 1800 208-230/460 SE CT 4:1 Yes 56C NVF3318GSKFA 15 $536TENV 0.33 1800 230/460 EE CT 10:1 Yes 56C NVF3318AEHFA $555TENV 0.33 1200 208-230/460 SE CT 4:1 Yes 56C NVF3312GSKFA 15 $658TENV 0.33 1200 230/460 EE CT 10:1 N 56C NVF3312AEHFA $669


44

General

Information

CM

100C

M 200

CM

300F

ootnotes


TENV 0.5 3600 208-230/460 SE CT 4:1 N 56C NV0F536GSKFA 15 $539TENV 0.5 3600 230/460 EE CT 10:1 N 56C NV0F536AEHFA $554TEFC 0.5 1800 208-230/460 SE CT 4:1 Yes 56C FC0F518GSKFA 15 $567TENV 0.5 1800 230/460 EE CT 10:1 Yes 56C NV0F518AEHFA $588TENV 0.5 1800 230/460 PE CT 1000:1 N 143TC NV0F518APZFA 50 $845TEFC 0.5 1200 230/460 SE CT 4:1 N 56C FC0F512ASKFA $689TENV 0.5 1200 230/460 EE CT 10:1 N 56C NV0F512AEHFA $698TENV 0.5 1200 230/460 PE CT 1000:1 N 143TC NV0F512APZFA 50 $997TEFC 0.75 3600 230/460 SE CT 4:1 N 56C FCF7536ASKFA $565TENV 0.75 3600 230/460 EE CT 10:1 N 56C NVF7536AEHFA $581TEFC 0.75 1800 208-230/460 SE CT 4:1 Yes 56C FCF7518GSKFA 15 $593TENV 0.75 1800 230/460 EE CT 10:1 Yes 56C NVF7518AEHFA $616TENV 0.75 1800 230/460 PE CT 1000:1 Yes 143TC NVF7518APZFA 50 $885TEFC 0.75 1200 208-230/460 SE CT 4:1 Yes 56C FCF7512GSKFA 15 $700TENV 0.75 1200 230/460 EE CT 10:1 N 56C NVF7512AEHFA $713TEFC 0.75 1200 230/460 EE CT 4:1 N 143TC FCF7512AEKFA $713TENV 0.75 1200 230/460 PE CT 1000:1 N 143TC NVF7512APZFA 50 $1,012TEFC 1 3600 208-230/460 SE CT 4:1 N 56C FC00136GSKFA 15 $594TEFC 1 3600 230/460 EE CT 4:1 N 56C FC00136AEKFA $613TENV 1 3600 230/460 PE CT 1000:1 Yes 143TC NV00136APZFA 50 $879TENV 1 1800 208-230/460 SE CT 4:1 Yes 56C NV00118GSKFA 15 $599TEFC 1 1800 208-230/460 SE CT 4:1 Yes 143TC FC00118GSKFA 15 $599TEFC 1 1800 230/460 EE CT 4:1 Yes 56C FC00118AEKF5A $624TEFC 1 1800 230/460 EE CT 4:1 Yes 143TC FC00118AEKF4A $624TENV 1 1800 230/460 PE CT 1000:1 Yes 143TC NV00118APZFA 50 $895TEFC 1 1200 208-230/460 SE CT 4:1 N 56C FC00112GSKFA 15 $726TEFC 1 1200 230/460 EE CT 4:1 N 56C FC00112AEKF5A $737TEFC 1 1200 230/460 EE CT 4:1 N 145TC FC00112AEKF4A $737TEFC 1 1200 230/460 PE CT 20:1 N 145TC FC00112APMFA 50 $1,051TEFC 1.5 3600 208-230/460 SE CT 4:1 N 56C FC1F536GSKFA 15 $650TEFC 1.5 3600 230/460 SE CT 4:1 N 143TC FC1F536ASKFA $650TEFC 1.5 3600 230/460 EE CT 4:1 N 56C FC1F536AEKF5A $673TEFC 1.5 3600 230/460 EE CT 4:1 N 143TC FC1F536AEKF4A $673TEFC 1.5 3600 230/460 PE CT 20:1 Yes 143TC FC1F536APMFA 50 $963TEFC 1.5 1800 208-230/460 SE CT 4:1 Yes 56C FC1F518GSKFA 15 $627TEFC 1.5 1800 208-230/460 SE CT 4:1 Yes 145TC FC1F518GSKFA 15 $627TEFC 1.5 1800 230/460 EE CT 4:1 Yes 56C FC1F518AEKF5A $639TEFC 1.5 1800 230/460 EE CT 4:1 Yes 145TC FC1F518AEKF4A $639TEFC 1.5 1800 230/460 PE CT 20:1 Yes 145TC FC1F518APMFA 50 $938TEFC 1.5 1200 230/460 PE CT 10:1 N 182TC FC1F512APHFA $946TEFC 2 3600 230/460 SE CT 4:1 N 56C FC00236ASKF5A $704TEFC 2 3600 230/460 SE CT 4:1 N 145TC FC00236ASKF4A $704TEFC 2 3600 230/460 EE CT 4:1 N 56C FC00236AEKF5A $730TEFC 2 3600 230/460 EE CT 4:1 N 145TC FC00236AEKF4A $730TEFC 2 3600 230/460 PE CT 20:1 Yes 145TC FC00236APMFA 50 $1,044TEFC 2 1800 208-230/460 SE CT 4:1 Yes 56C FC00218GSKF5A 15 $655TEFC 2 1800 208-230/460 SE CT 4:1 Yes 145TC FC00218GSKF4A 15 $655TEFC 2 1800 230/460 EE CT 4:1 N 56C FC00218AEKF5A $669TEFC 2 1800 230/460 EE CT 4:1 Yes 145TC FC00218AEKF4A $669TEFC 2 1800 230/460 PE CT 20:1 Yes 145TC FC00218APMFA 50 $981TEFC 2 1200 230/460 PE CT 10:1 N 184TC FC00212APHFA $1,020


45

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 3 3600 230/460 PE CT 10:1 N 182TC FC00336APHFA $942TEFC 3 1800 230/460 SE CT 4:1 Yes 145TC FC00318ASKFA $683TEFC 3 1800 230/460 PE CT 10:1 Yes 182TC FC00318APHFA $923TEFC 3 1200 230/460 PE CT 10:1 N 213TC FC00312APHFA $1,171TEFC 5 3600 230/460 PE CT 10:1 N 184TC FC00536APHFA $1,058TEFC 5 1800 230/460 PE CT 10:1 Yes 184TC FC00518APHFA $1,029TEFC 5 1200 230/460 PE CT 10:1 N 215TC FC00512APHFA $1,530TEFC 7.5 3600 230/460 PE CT 10:1 N 213TC FC7F536APHFA $1,285TEFC 7.5 1800 230/460 PE CT 10:1 Yes 213TC FC7F518APHFA $1,278TEFC 10 3600 230/460 PE CT 10:1 N 215TC FC01036APHFA $1,452TEFC 10 1800 230/460 PE CT 10:1 Yes 215TC FC01018APHFA $1,390TEFC 15 1800 460 PE CT 4:1 (10) Yes 254TC FC01518BPKFA $1,859TEFC 15 1800 230/460 PE CT 4:1 (10) Yes 254TC FC01518APKFA $1,859TEFC 20 1800 230/460 PE CT 4:1 (10) Yes 256TC FC02018APKFA $2,136TEFC 20 1800 460 PE CT 4:1 (10) Yes 256TC FC02018BPKFA $2,136TEFC 25 1800 230/460 PE CT 4:1 (10) Yes 284TC FC02518APKFA $2,694TEFC 25 1800 460 PE CT 4:1 (10) Yes 284TC FC02518BPKFA $2,694TEFC 30 1800 230/460 PE CT 4:1 (10) Yes 286TC FC03018APKFA $3,071TEFC 30 1800 460 PE CT 4:1 (10) Yes 286TC FC03018BPKFA $3,071


(10) Note: CT 4 :1 (10) = Constant Torque 4:1 Speed Range (capable of 10:1 CT with fan change), must add modification code 126

(2) Note: VT 10:1 (2) = Variable Torque 10:1 Speed Range (capable of 2:1 CT with fan change), must add modification code 126(10) Note: CT 2:1 (10) = Constant Torque 2:1 Speed Range (capable of 10:1 CT with fan change), must add modification code 126


46

General

Information

CM

100C

M 200

CM

300F

ootnotes


Once shipped, modified motors cannot be returned.

Delivery Cycle



CONDUIT BOX: Mounting of stock box kits (price includes box).102 Add auxiliary box attached to main conduit box 140-445 $618 103103 Drill drain hole 56-449 $188 103



112 Stainless steel T-drain 180-449 $618 103END BRACKET: Modify a foot mounted motor to include a C-Face end bracket.Note: Please add seal modification seperately if required.



126 Convert to larger fan for increased Constant Torque speed range on inverter 180-280 $314 103(increases range as noted on catalog page). 320-449 $439 103GREASE FITTINGS: Install a grease fitting on each bearing.








Note: Not available on L180-L210 frames 320-449 $376




47

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Modifications Available to CM111 MotorsSEALS: Addition of shaft seal.


180 Addition of 120V single phase, 60 Hz space heater, aux CB not included 48, 56, 140 $359180-280 $419320-400 $470440-L449 $589

THERMAL PROTECTION: Addition of thermostats. Standard in Component Class Motors All incl

160 Removal of standard thermostats from motor (deduct from List Price) 48-280 -$208Note: User must insure that NEC 2005 is met for inverter duty motor 320-449 -$313


48

General

Information

CM

100C

M 200

CM

300F

ootnotes


Component ClassInverter Duty Harsh Environment SeriesCM112 Family - IEEE 841 AC Motors



Frequency: 60 Hz Duty Cycle: Continuous PE = Premium Efficient motors that exceed EPAct efficiency levels.Ambient: 40° C Insulation: Class F

Service Factor: 1.00 Temp. Rise: Class F NP = NEMA Premium efficient motors.

Warranty (From Date Of Manufacture /


Application InformationExceeds IEEE841 requirements, designed for long life and reliable operation in severe industrial applications. Built for durability in moist, contaminated, harsh environments such as chemical plants, petroleum refineries and paper mills.

PE & NP (60 / 48)


140T FramesMaterials: Cast iron frame, end shields, conduit box and fan coverConduit Box: F1 locationBearing Type: Double sealedBearing Protection: Inpro seals both endsShaft Material: Stainless SteelNameplate Material: Stainless SteelDrain Type & Location: T-drain in each end shield

180T - 449T FramesMaterials: Cast iron frame, end shields, conduit box and fan coverConduit Box: F1 location, diagonally split, rotatable in 90 degree increments,

gasketed cover, NPT threaded lead outlet, lead separator gasket to frame, UL listed clamp-type ground lug.

Bearing Type: Open ball PLS (Positive Lubrication System)Bearing Protection: Inpro seal each end plus cast iron inner caps inboardShaft Material: High strength carbon steelNameplate Material: Stainless SteelDrain Type & Location: Stainless steel T-drain in each end shieldAdditional Features: RTV sealed bracket-to-frame fits, epoxy coated rotor and stator,

alemite grease fittings, Gits cup grease relief fittings, lead lugs, low vibration, and quiet operation (below 90 dBA sound power). Insulation system on all EE, PE and NP motors exceeds NEMA MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

CM112 Family - IEEE 841 AC Motors

49

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Component Class, IInverter Duty Harsh Environment SeriesCM112 Family - IEEE 841 AC Motors


RPM Class Torque/Spd Stock CM112- PriceTENV 0.5 1800 460 PE CT 1000:1 N 143T NV0F518BPZHA $896TENV 0.5 1200 460 PE CT 1000:1 N 143T NV0F512BPZHA $990TENV 0.75 1800 460 PE CT 1000:1 N 143T NVF7518BPZHA $927TENV 0.75 1200 460 PE CT 1000:1 N 143T NVF7512BPZHA $1,000TENV 1 3600 460 NP CT 1000:1 yes 143T NV00136BNZHA $906TENV 1 1800 460 NP CT 1000:1 yes 143T NV00118BNZHA $938TEFC 1 1200 460 NP CT 10:1 N 182T FC00112BNHHA $955TEFC 1 900 460 PE CT 10:1 N L182T FC00109BPHHA $1,283TEFC 1.5 3600 460 NP CT 20:1 yes 143T FC1F536BNMHA $969TEFC 1.5 1800 460 NP CT 20:1 yes 145T FC1F518BNMHA $969TEFC 1.5 1200 460 NP CT 10:1 N L182T FC1F512BNHHA $955TEFC 1.5 900 460 PE CT 10:1 N 182T FC1F509BPHHA $1,345TEFC 2 3600 460 NP CT 20:1 yes 145T FC00236BNMHA $900TEFC 2 1800 460 NP CT 20:1 yes 145T FC00218BNMHA $1,000TEFC 2 1200 460 NP CT 10:1 N L184T FC00212BNHHA $999TEFC 2 900 460 PE CT 10:1 N L213T FC00209BPHHA $1,577TEFC 3 3600 460 NP CT 10:1 yes 182T FC00336BNHHA $1,009TEFC 3 1800 460 NP CT 10:1 N L182T FC00318BNHHA $942TEFC 3 1200 460 NP CT 10:1 yes 213T FC00312BNHHA $1,161TEFC 3 900 460 PE CT 10:1 N L215T FC00309BPHHA $1,827TEFC 5 3600 460 NP CT 10:1 yes 184T FC00536BNHHA $1,079TEFC 5 1800 230/460 NP CT 10:1 N L184T FC00518ANHHA 35 $1,005TEFC 5 1200 460 NP CT 10:1 yes L215T FC00512BNHHA $1,563TEFC 5 900 460 PE CT 4:1 (10) N 254T FC00509BPKHA $2,689TEFC 7.5 3600 460 NP CT 10:1 yes 213T FC7F536BNHHA $1,294TEFC 7.5 1800 460 NP CT 10:1 N L213T FC7F518BNHHA $1,229TEFC 7.5 1200 460 NP CT 4:1 (10) N 254T FC7F512BNKHA $2,142TEFC 7.5 900 460 PE CT 10:1 N 256T FC7F509BPHHA $3,275TEFC 10 3600 460 NP CT 10:1 yes 215T FC01036BNHHA $1,399TEFC 10 1800 460 NP CT 10:1 N L215T FC01018BNHHA $1,300TEFC 10 1200 460 NP CT 4:1 (10) yes 256T FC01012BNKHA $2,440TEFC 10 900 460 PE CT 4:1 (10) N 284T FC01009BPKHA $3,989TEFC 15 3600 460 NP CT 4:1 (10) yes 254T FC01536BNKHA $2,170TEFC 15 1800 460 NP CT 4:1 (10) yes 254T FC01518BNKHA $2,030TEFC 15 1200 460 NP CT 4:1 (10) yes 284T FC01512BNKHA $3,333TEFC 15 900 460 PE CT 4:1 (10) N 286T FC01509BPKHA $4,783TEFC 20 3600 460 NP CT 4:1 (10) yes 256T FC02036BNKHA $2,430TEFC 20 1800 460 NP CT 4:1 (10) N 256T FC02018BNKHA $2,267TEFC 20 1200 460 NP CT 4:1 (10) yes 286T FC02012BNKHA $3,869TEFC 20 900 460 PE CT 4:1 (10) N 324T FC02009BPKHA $5,991TEFC 25 3600 460 NP CT 4:1 (10) yes 284TS FC02536BNKHA $3,158TEFC 25 1800 460 NP CT 4:1 (10) yes 284T FC02518BNKHA $2,986TEFC 25 1200 460 NP CT 4:1 (10) yes 324T FC02512BNKHA $4,944TEFC 25 900 460 PE CT 4:1 (10) N 326T FC02509BPKHA $6,684TEFC 30 3600 460 NP CT 4:1 (10) yes 286TS FC03036BNKHA $3,538TEFC 30 1800 460 NP CT 4:1 (10) yes 286T FC03018BNKHA $3,333TEFC 30 1200 460 NP CT 4:1 (10) yes 326T FC03012BNKHA $5,481TEFC 30 900 460 PE CT 4:1 (10) N 364T FC03009BPKHA $7,897TEFC 40 3600 460 NP CT 4:1 (10) yes 324TS FC04036BNKHA $4,663TEFC 40 1800 460 NP CT 4:1 (10) yes 324T FC04018BNKHA $4,532TEFC 40 1200 460 NP CT 4:1 (10) yes 364T FC04012BNKHA $7,222TEFC 40 900 460 PE CT 4:1 (10) N 365T FC04009BPKHA $9,305TEFC 50 3600 460 NP CT 4:1 (10) yes 326TS FC05036BNKHA $5,623TEFC 50 1800 460 NP CT 4:1 (10) yes 326T FC05018BNKHTA $5,120TEFC 50 1800 460 NP CT 4:1 (10) N 326TS FC05018BNKHSA $5,120TEFC 50 1200 460 NP CT 4:1 (10) yes 365T FC05012BNKHA $8,190TEFC 50 900 460 PE CT 4:1 (10) N 404T FC05009BPKHA $11,055


50

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 60 3600 460 NP CT 4:1 (10) yes 364TS FC06036BNKHA $7,434TEFC 60 1800 460 NP CT 4:1 (10) yes 364T FC06018BNKHTA $7,204TEFC 60 1800 460 NP CT 4:1 (10) N 364TS FC06018BNKHSA $7,204TEFC 60 1200 460 NP CT 4:1 (10) yes 404T FC06012BNKHA $9,510TEFC 60 900 460 PE CT 4:1 (10) N 405T FC06009BPKHA $12,441TEFC 75 3600 460 NP CT 4:1 (10) yes 365TS FC07536BNKHA $8,827TEFC 75 1800 460 NP CT 4:1 (10) N 365T FC07518BNKHTA $8,478TEFC 75 1800 460 NP CT 4:1 (10) N 365TS FC07518BNKHSA $8,478TEFC 75 1200 460 NP CT 4:1 (10) yes 405T FC07512BNKHA $10,415TEFC 75 900 460 PE CT 4:1 (10) N 444T FC07509BPKHA $16,007TEFC 100 3600 460 NP CT 4:1 (10) yes 405TS FC10036BNKHA $11,273TEFC 100 1800 460 NP CT 4:1 (10) yes 405T FC10018BNKHTA $10,366TEFC 100 1800 460 NP CT 4:1 (10) N 405TS FC10018BNKHSA $10,366TEFC 100 1200 460 NP CT 4:1 (10) yes 444T FC10012BNKHA $13,315TEFC 100 900 460 PE CT 4:1 (10) N 445T FC10009BPKHA $19,471TEFC 125 3600 460 NP CT 4:1 (10) yes 444TS FC12536BNKHA $14,319TEFC 125 1800 460 NP CT 4:1 (10) yes 444T FC12518BNKHTA $13,265TEFC 125 1800 460 NP CT 4:1 (10) N 444TS FC12518BNKHSA $13,265TEFC 125 1200 460 NP CT 2:1 (10) yes 445T FC12512BNJHA $15,803TEFC 125 900 460 PE CT 2:1 (10) N 449T FC12509BPJHB $21,127TEFC 125 900 460 PE CT 2:1 (10) N 449T FC12509BPJUA 5 $21,127TEFC 150 3600 460 NP CT 4:1 (10) yes 445TS FC15036BNKHA $16,892TEFC 150 1800 460 NP CT 4:1 (10) N 445TS FC15018BNKHSA $15,195TEFC 150 1800 460 NP CT 4:1 (10) yes 445T FC15018BNKHTA $15,195TEFC 150 1200 460 NP CT 2:1 (10) yes 447T FC15012BNJUA 5 $19,175TEFC 150 1200 460 NP CT 2:1 (10) yes 447T FC15012BNJHB $19,175TEFC 150 900 460 PE CT 2:1 (10) N 449T FC15009BPJHB $26,418TEFC 150 900 460 PE CT 2:1 (10) N 449T FC15009BPJUA 5 $26,418TEFC 200 3600 460 NP CT 4:1 (10) yes 445TS FC20036BNKHA $20,957TEFC 200 1800 460 NP CT 2:1 (10) yes 447T FC20018BNJHB $18,660TEFC 200 1800 460 NP CT 2:1 (10) yes 447T FC20018BNJUA 5 $18,660TEFC 200 1200 460 NP CT 2:1 (10) yes 449T FC20012BNJUA 5 $21,294TEFC 200 1200 460 NP CT 2:1 (10) yes 449T FC20012BNJHB $21,294TEFC 200 900 460 PE CT 2:1 (10) N 449T FC20009BPJHA $26,736TEFC 250 3600 460 NP CT 2:1 (10) yes 449TS FC25036BNJHA $26,408TEFC 250 1800 460 NP CT 2:1 (10) yes 449T FC25018BNJUA 5 $21,600



RPM Class Torque/Spd Stock CM112- PriceTENV 1 3600 460 PE CT 1000:1 yes FL143TC NV00136BPZCA $859TENV 1 1800 460 PE CT 1000:1 yes FL143TC NV00118BPZCA $884TEFC 1.5 3600 460 PE CT 20:1 yes FL143TC FC1F536BPMCA $909TEFC 1.5 1800 460 PE CT 20:1 yes FL145TC FC1F518BPMCA $911TEFC 2 3600 460 PE CT 20:1 yes FL145TC FC00236BPMCA $957TEFC 2 1800 460 PE CT 20:1 yes FL145TC FC00218BPMCA $939TEFC 3 3600 460 PE CT 10:1 yes 182TC FC00336BPHCA $1,093TEFC 3 1800 460 PE CT 10:1 yes 182TC FC00318BPHCA $1,025TEFC 5 3600 460 PE CT 10:1 yes 184TC FC00536BPHCA $1,161TEFC 5 1800 460 PE CT 10:1 yes L184TC FC00518BPHCA $1,089TEFC 7.5 3600 460 PE CT 10:1 yes 213TC FC7F536BPHCA $1,378TEFC 7.5 1800 460 PE CT 10:1 yes 213TC FC7F518BPHCA $1,313TEFC 10 3600 460 PE CT 10:1 yes 215TC FC01036BPHCA $1,482TEFC 10 1800 460 PE CT 10:1 yes L215TC FC01018BPHCA $1,383TEFC 15 3600 460 PE CT 4:1 (10) yes 254TC FC01536BPKCA $2,279TEFC 15 1800 460 PE CT 4:1 (10) yes 254TC FC01518BPKCA $2,140


51

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 20 3600 460 PE CT 4:1 (10) yes 256TC FC02036BPKCA $2,540TEFC 20 1800 460 PE CT 4:1 (10) yes 256TC FC02018BPKCA $2,376TEFC 25 1800 460 PE CT 4:1 (10) yes 284TC FC02518BPKCA $3,136TEFC 30 1800 460 PE CT 4:1 (10) yes 286TC FC03018BPKCA $3,484TEFC 40 1800 460 PE CT 4:1 (10) yes 324TC FC04018BPKCA $4,767TEFC 50 1800 460 PE CT 4:1 (10) yes 326TC FC05018BPKCA $5,354TEFC 60 1800 460 PE CT 4:1 (10) yes 364TC FC06018BPKCA $7,538TEFC 75 1800 460 PE CT 4:1 (10) yes 365TC FC07518BPKCA $8,811


C-Face Footless IP55Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Catalog String Notes US List

RPM Class Torque/Spd Stock CM112- PriceTENV 1 3600 460 PE CT 1000:1 yes 143TC NV00136BPZFA $854TENV 1 1800 460 PE CT 1000:1 yes 143TC NV00118BPZFA $879TEFC 1.5 3600 460 PE CT 20:1 yes 143TC FC1F536BPMFA $904TEFC 1.5 1800 460 PE CT 20:1 yes 145TC FC1F518BPMFA $906TEFC 2 3600 460 PE CT 20:1 yes 145TC FC00236BPMFA $952TEFC 2 1800 460 PE CT 20:1 yes 145TC FC00218BPMFA $933TEFC 3 3600 460 PE CT 10:1 yes 182TC FC00336BPHFA $1,113TEFC 3 1800 460 PE CT 10:1 yes 182TC FC00318BPHFA $1,045TEFC 5 3600 460 PE CT 10:1 yes 184TC FC00536BPHFA $1,181TEFC 5 1800 460 PE CT 10:1 yes L184TC FC00518BPHFA $1,108TEFC 7.5 3600 460 PE CT 10:1 yes 213TC FC7F536BPHFA $1,398TEFC 7.5 1800 460 PE CT 10:1 yes 213TC FC7F518BPHFA $1,332TEFC 10 3600 460 PE CT 10:1 yes 215TC FC01036BPHFA $1,502TEFC 10 1800 460 PE CT 10:1 yes 215TC FC01018BPHFA $1,403TEFC 15 3600 460 PE CT 4:1 (10) yes 254TC FC01536BPKFA $2,326TEFC 15 1800 460 PE CT 4:1 (10) yes 254TC FC01518BPKFA $2,186TEFC 20 3600 460 PE CT 4:1 (10) yes 256TC FC02036BPKFA $2,586TEFC 20 1800 460 PE CT 4:1 (10) yes 256TC FC02018BPKFA $2,423


(2) Note: VT 10:1 (2) = Variable Torque 10:1 Speed Range (capable of 2:1 CT with fan change), must add modification code 126(10) Note: CT 2:1 (10) = Constant Torque 2:1 Speed Range (capable of 10:1 CT with fan change), must add modification code 126(10) Note: CT 4 :1 (10) = Constant Torque 4:1 Speed Range (capable of 10:1 CT with fan change), must add modification code 126


52

General

Information

CM

100C

M 200

CM

300F

ootnotes



Delivery Cycle




FAN CHANGE: Install larger fan.126 Convert to larger fan for increased Constant Torque speed range on inverter 180-280 $314 103

(increases range as noted on catalog page). 320-449 $439 103MOUNTING: Move conduit box to allow different mounting configurations.













53

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Component ClassInverter Duty Harsh Environment SeriesCM113 Family - Aggregate Duty AC Motors



Frequency: 60 Hz Duty Cycle: Continuous EE = Energy Efficient motors that meet EPAct efficienciesAmbient: 40° C Insulation: Class F



Application InformationDesigned with high starting torque and breakdown torque for heavily loaded conveyor and crusher applications. Includes severe duty mechanical features for longer life and durability in harsh environments..

EE (36 / 24)

Nameplate Agency Approvals:CE, CSA, IEEE45

180T - 449T FramesMaterials: Cast iron frame, end shields, conduit box and fan cover

Conduit Box: F1 location, diagonally split, rotatable in 90 degree increments, gasketed, NPT threaded lead outlet

Bearing Type: Open, PLS

Bearing Protection: V-ring slinger on both ends


Nameplate Material: Stainless Steel

Drain Type & Location:

T-drain on drive end

Additional Features: All 405T frames and larger have Inpro type mechanical labrynth seals on the drive end.All frame sizes are suitable for vertical applications without the need for modification.All 405T frames and larger have roller bearings on the drive end.75 HP, 360 frame size and below are NEMA Design C.75 HP, 405T frame size and large are NEMA Design A.Insulation system exceeds NEMA MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

CM113 Family - Aggregate Duty AC Motors

54

General

Information

CM

100C

M 200

CM

300F

ootnotes

Component Class, Inverter Duty Harsh Environment SeriesCM113 Family - Aggregate Duty AC Motors


RPM Class Torque/Spd Stock CM113- PriceTEFC 5 1800 230/460 EE VT 10:1 (2) yes 184T FC00518AEVHA $1,090TEFC 7.5 1800 230/460 EE VT 10:1 (2) yes 213T FC7F518AEVHA $1,315TEFC 10 1800 230/460 EE VT 10:1 (2) yes 215T FC01018AEVHA $1,432TEFC 15 1800 230/460 EE VT 10:1 (2) yes 254T FC01518AEVHA $1,932TEFC 20 1800 230/460 EE VT 10:1 (2) yes 256T FC02018AEVHA $1,971TEFC 25 1800 230/460 EE VT 10:1 (2) yes 284T FC02518AEVHA $2,470TEFC 30 1800 230/460 EE VT 10:1 (2) yes 286T FC03018AEVHA $2,513TEFC 40 1800 230/460 EE VT 10:1 (2) yes 324T FC04018AEVHA $3,882TEFC 50 1800 230/460 EE VT 10:1 (2) yes 326T FC05018AEVHA $4,102TEFC 60 1800 230/460 EE VT 10:1 (2) yes 364T FC06018AEVHA $4,691TEFC 75 1800 230/460 EE VT 10:1 (2) yes 365T FC07518AEVHA $4,719TEFC 75 1200 460 EE VT 10:1 (2) yes 405T FC07512BEVUA 5 $9,125TEFC 100 1800 460 EE VT 10:1 (2) yes 405T FC10018BEVUA 5 $6,961TEFC 100 1200 460 EE VT 10:1 (2) yes 444T FC10012BEVUA 5 $10,104TEFC 125 1800 460 EE VT 10:1 (2) yes 444T FC12518BEVUA 5 $8,782TEFC 125 1200 460 EE VT 10:1 (2) yes 445T FC12512BEVUA 5 $10,721TEFC 150 1800 460 EE VT 10:1 (2) yes 445T FC15018BEVUA 5 $9,458TEFC 150 1200 460 EE VT 10:1 (2) yes 447T FC15012BEVUA 5 $17,712TEFC 200 1800 460 EE VT 10:1 (2) yes 447T FC20018BEVUA 5 $16,567TEFC 200 1200 460 EE VT 10:1 (2) yes 447T FC20012BEVUA 5 $19,024TEFC 250 1800 460 EE VT 10:1 (2) yes 447T FC25018BEVUA 5 $18,922TEFC 250 1200 460 EE VT 10:1 (2) yes 449T FC25012BEVUA 5 $19,308TEFC 300 1800 460 EE VT 10:1 (2) yes 449T FC30018BEVUA 5 $19,113TEFC 350 1800 460 EE VT 10:1 (2) yes 449T FC35018BEVUA 5 $22,344


(2) Note: VT 10:1 (2) = Variable Torque 10:1 Speed Range (capable of 2:1 CT with fan change), must add modification code 126


55

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es






CONNECTIONS: Final connect dual to single voltage.107 High Voltage Connection (price by frame size) 180-320 $188

END BRACKET: Modify a foot mounted motor to include a C-Face end bracket.Note: Please add seal modification seperately if required.

121 Changing from std. end to C-face with feet (Non-NEMA BA) 180-250 $493122 Changing from std. end to C-face with feet (NEMA BA) 280-360 $744


126 Convert to larger fan for increased Constant Torque speed range on inverter 180-280 $314 103(increases range as noted on catalog page). 320-449 $439 103MOUNTING: Move conduit box to allow different mounting configurations.






180 Addition of 120V single phase, 60 Hz space heater, aux CB not included 48, 56, 140 $359180-280 $419320-400 $470440-L449 $589






56

General

Information

CM

100C

M 200

CM

300F

ootnotes

Changes to an Order


Component ClassInverter Duty Harsh Environment SeriesCM115 Family - Washdown Duty White Epoxy Coated AC Motors



Frequency: 60 Hz Duty Cycle: Continuous EE = Energy Efficient motors that meet EPAct efficiencies.Ambient: 40° C Insulation: Class F



(24 / 12)

Application InformationFor service in washdown applications subject to sanitary codes. BISSC certification standard on 180T - 256T frame sizes and optional on 56 - 145T frame sizes.


56 - 140T FramesMaterials: Rolled steel frame and fan cover, cast aluminum conduit box,

cast iron end shields.Conduit Box: Oversized, top mounted with F1 and F2 lead outlets.Bearing Type: Double sealed ball bearings.Bearing Protection: Lip seal on both ends and drive end shaft slinger.Shaft Material: 300 series stainless steel.Nameplate Material: Adhesive MylarDrain Type & Location: Automatic T-drains every 90 degrees.Additional Features: White epoxy paint.

Insulation system exceeds NEMA MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

180T - 256T FramesMaterials: Smooth cast iron frame and end shields. Steel conduit box and fan cover.Conduit Box: F1 location, diagonally split, rotatable in 90 degree increments.Bearing Type: Double sealedBearing Protection: Lip seal and slingerShaft Material: Carbon steelNameplate Material: Stainless steelDrain Type & Location: T-drainsAdditional Features: White epoxy paint.

Insulation system exceeds NEMA MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

CM115 Family - Washdown Duty White Epoxy Coated AC Motors

57

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Component Class, Inverter Duty Harsh Environment SeriesCM115 Family - Washdown Duty AC Motors


RPM Class Torque/Spd Stock CM115- PriceTENV 0.5 3600 230/460 EE CT 4:1 N 56 NV0F536AEKHA $551TEFC 0.5 1800 208-230/460 EE CT 4:1 yes 56 FC0F518GEKHA 15 $578TENV 0.5 1800 208-230/460 EE CT 4:1 yes 56 NV0F518GEKHA 15 $578TENV 0.75 3600 230/460 EE CT 4:1 N 56 NVF7536AEKHA $576TEFC 0.75 1800 208-230/460 EE CT 4:1 yes 56 FCF7518GEKHA 15 $596TENV 0.75 1800 208-230/460 EE CT 4:1 yes 56 NVF7518GEKHA 15 $596TENV 1 3600 230/460 EE CT 4:1 N 56 NV00136AEKHA $609TEFC 1 1800 230/460 PE CT 4:1 yes 143T FC00118APKHA $735TENV 1 1800 230/460 EE CT 4:1 N 56 NV00118AEKHA $614TEFC 1 1800 230/460 EE CT 4:1 yes 143T FC00118AEKHA 15 $614TENV 1 1800 208-230/460 EE CT 4:1 yes 143T NV00118GEKHA 15 $614TENV 1.5 3600 230/460 EE CT 4:1 N 56 NV1F536AEKHA $673TENV 1.5 3600 230/460 EE CT 4:1 N 143T NV1F536AEKHA $673TEFC 1.5 1800 230/460 PE CT 4:1 yes 145T FC1F518APKHA $786TENV 1.5 1800 230/460 EE CT 4:1 N 56 NV1F518AEKHA $653TEFC 1.5 1800 208-230/460 EE CT 4:1 yes 145T FC1F518GEKHA 15 $653TENV 1.5 1800 208-230/460 EE CT 4:1 yes 145T NV1F518GEKHA 15 $653TEFC 2 3600 230/460 EE CT 4:1 N 56 FC00236AEKHA $773TEFC 2 3600 230/460 EE CT 4:1 N 145T FC00236AEKHA $773TEFC 2 1800 230/461 PE CT 4:1 yes 145T FC00218APKHA $928TEFC 2 1800 230/460 EE CT 4:1 N 56 FC00218AEKHA $794TEFC 2 1800 208-230/460 EE CT 4:1 yes 145T FC00218GEKHA 15 $762TEFC 3 3600 230/460 EE CT 4:1 N 145T FC00336AEKHA $896TEFC 3 1800 230/460 PE CT 2:1 yes 182T FC00318APJHA $1,165TEFC 3 1800 230/460 EE CT 2:1 yes 184T FC00318AEJHA 51 $944TEFC 5 1800 230/460 PE CT 2:1 yes 184T FC00518APJHA $1,301TEFC 5 1800 230/460 EE CT 2:1 yes 184T FC00518AEJHA 51 $1,048TEFC 7.5 1800 230/460 PE CT 2:1 yes 213T FC7F518APJHA $1,574TEFC 7.5 1800 230/460 EE CT 2:1 yes 215T FC7F518AEJHA 51 $1,259TEFC 10 1800 230/460 PE CT 2:1 yes 215T FC01018APJHA $1,842TEFC 10 1800 230/460 EE CT 2:1 yes 215T FC01018AEJHA 51 $1,465



RPM Class Torque/Spd Stock CM115- PriceTENV 0.5 3600 208-230/460 EE CT 4:1 yes 56C NV0F536GEKCA 15 $553TEFC 0.5 1800 208-230/460 EE CT 4:1 yes 56C FC0F518GEKCA 15 $595TENV 0.5 1800 208-230/460 EE CT 4:1 yes 56C NV0F518GEKCA 15 $595TENV 0.5 1200 208-230/460 EE CT 4:1 N 56C NV0F512GEKCA 15 $663TENV 0.75 3600 208-230/460 EE CT 4:1 yes 56C NVF7536GEKCA 15 $587TEFC 0.75 1800 208-230/460 EE CT 4:1 yes 56C FCF7518GEKCA 15 $656TENV 0.75 1800 208-230/460 EE CT 4:1 yes 56C NVF7518GEKCA 15 $656TEFC 0.75 1200 208-230/460 EE CT 4:1 N 56C FCF7512GEKCA 15 $699TENV 1 3600 208-230/460 EE CT 4:1 yes 56C NV00136GEKCA 15 $652TEFC 1 1800 230/460 PE CT 4:1 yes 143TC FC00118APKCA $815TENV 1 1800 208-230/460 EE CT 4:1 yes 56C NV00118GEKCA 15 $675TEFC 1 1800 208-230/460 EE CT 4:1 yes 143TC FC00118GEKCA 15 $675TENV 1 1800 208-230/460 EE CT 4:1 yes 143TC NV00118GEKCA 15 $675TEFC 1 1200 208-230/460 EE CT 4:1 N 145TC FC00112GEKCA 15 $770


58

General

Information

CM

100C

M 200

CM

300F

ootnotes


TENV 1.5 3600 208-230/460 EE CT 4:1 yes 56C NV1F536GEKCA 15 $699TENV 1.5 3600 208-230/460 EE CT 4:1 yes 143TC NV1F536GEKCA 15 $699TEFC 1.5 1800 230/460 PE CT 4:1 yes 143TC FC1F518APKCA $842TENV 1.5 1800 208-230/460 EE CT 4:1 yes 56C NV1F518GEKCA 15 $696TEFC 1.5 1800 208-230/460 EE CT 4:1 yes 145TC FC1F518GEKCA 15 $696TENV 1.5 1800 208-230/460 EE CT 4:1 yes 145TC NV1F518GEKCA 15 $696TEFC 1.5 1200 208-230/460 EE CT 4:1 N 145TC FC1F512GEKCA 15 $781TEFC 2 3600 208-230/460 EE CT 4:1 yes 56C FC00236GEKC5A 15 $752TEFC 2 3600 208-230/460 EE CT 4:1 yes 145TC FC00236GEKC4A 15 $786TEFC 2 1800 230/460 PE CT 4:1 yes 145TC FC00218APKCA $992TEFC 2 1800 208-230/460 EE CT 4:1 yes 56C FC00218GEKC5A 15 $811TEFC 2 1800 208-230/460 EE CT 4:1 yes 145TC FC00218GEKC4A 15 $811TEFC 3 3600 208-230/460 EE CT 4:1 yes 145TC FC00336GEKCA 15 $919TEFC 3 3600 230/460 EE CT 2:1 yes 184TC FC00336AEJCA 51 $1,110TEFC 3 1800 230/460 PE CT 2:1 yes 182TC FC00318APJCA $1,243TEFC 3 1800 230/460 EE CT 2:1 yes 184TC FC00318AEJCA 51 $1,005TEFC 5 3600 230/460 EE CT 2:1 yes 184TC FC00536AEJCA 51 $1,207TEFC 5 1800 230/460 PE CT 2:1 yes 184TC FC00518APJCA $1,381TEFC 5 1800 230/460 EE CT 2:1 yes 184TC FC00518AEJCA 51 $1,110TEFC 7.5 3600 230/460 EE CT 2:1 yes 215TC FC7F536AEJCA 51 $1,447TEFC 7.5 1800 230/460 PE CT 2:1 yes 213TC FC7F518APJCA $1,696TEFC 7.5 1800 230/460 EE CT 2:1 yes 215TC FC7F518AEJCA 51 $1,352TEFC 10 3600 230/460 EE CT 2:1 yes 215TC FC01036AEJCA 51 $1,680TEFC 10 1800 230/460 PE CT 2:1 yes 215TC FC01018APJCA $1,897TEFC 10 1800 230/460 EE CT 2:1 yes 215TC FC01018AEJCA 51 $1,508TEFC 15 3600 230/460 EE CT 2:1 yes 256TC FC01536AEJCA 51 $2,582TEFC 15 1800 230/460 PE CT 2:1 yes 254TC FC01518APJCA $3,294TEFC 15 1800 230/460 EE CT 2:1 yes 256TC FC01518AEJCA 51 $2,582TEFC 20 3600 230/460 EE CT 2:1 yes 256TC FC02036AEJCA 51 $2,978TEFC 20 1800 230/460 PE CT 2:1 yes 256TC FC02018APJCA $3,788TEFC 20 1800 230/460 EE CT 2:1 yes 256TC FC02018AEJCA 51 $2,962

Discount Schedule 16 CC049A

C-Face Footless IP55Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Notes US List

RPM Class Torque/Spd Stock PriceTENV 0.5 3600 208-230/460 EE CT 4:1 N 56C NV0F536GEKFA 15 $560TEFC 0.5 1800 208-230/460 EE CT 4:1 yes 56C FC0F518GEKFA 15 $584TENV 0.5 1800 208-230/460 EE CT 4:1 yes 56C NV0F518GEKFA 15 $584TENV 0.75 3600 208-230/460 EE CT 4:1 N 56C NVF7536GEKFA 15 $582TEFC 0.75 1800 208-230/460 EE CT 4:1 yes 56C FCF7518GEKFA 15 $644TENV 0.75 1800 208-230/460 EE CT 4:1 yes 56C NVF7518GEKFA 15 $644TENV 1 3600 208-230/460 EE CT 4:1 N 56C NV00136GEKFA 15 $647TEFC 1 1800 230/460 PE CT 4:1 yes 143TC FC00118APKFA $800TENV 1 1800 208-230/460 EE CT 4:1 yes 56C NV00118GEKF5A 15 $674TEFC 1 1800 208-230/460 EE CT 4:1 yes 143TC FC00118GEKFA 15 $674TENV 1 1800 208-230/460 EE CT 4:1 yes 143TC NV00118GEKF4A 15 $664TENV 1.5 3600 208-230/460 EE CT 4:1 N 56C NV1F536GEKF5A 15 $699TENV 1.5 3600 208-230/460 EE CT 4:1 N 143TC NV1F536GEKF4A 15 $699TEFC 1.5 1800 230/460 PE CT 4:1 yes 143TC FC1F518APKFA $838TENV 1.5 1800 208-230/460 EE CT 4:1 yes 56C NV1F518GEKF5A 15 $693TEFC 1.5 1800 208-230/460 EE CT 4:1 yes 145TC FC1F518GEKFA 15 $693TENV 1.5 1800 208-230/460 EE CT 4:1 yes 145TC NV1F518GEKF4A 15 $693TEFC 2 3600 208-230/460 EE CT 4:1 N 56C FC00236GEKF5A 15 $759TEFC 2 3600 208-230/460 EE CT 4:1 N 145TC FC00236GEKF4A 15 $759TEFC 2 1800 230/460 PE CT 4:1 yes 145TC FC00218APKFA $927TEFC 2 1800 208-230/460 EE CT 4:1 yes 56C FC00218GEKF5A 15 $761TEFC 2 1800 208-230/460 EE CT 4:1 yes 145TC FC00218GEKF4A 15 $761


59

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 3 3600 208-230/460 EE CT 4:1 yes 56C FC00336GEKF5A 15 $765TEFC 3 3600 208-230/460 EE CT 4:1 N 145TC FC00336GEKF4A 15 $765TEFC 3 1800 208-230/460 EE CT 4:1 yes 145TC FC00318GEKFA 15 $808TEFC 3 1800 230/460 PE CT 2:1 yes 182TC FC00318APJFA $1,156TEFC 3 1800 230/460 EE CT 2:1 yes 184TC FC00318AEJFA 51,75 $937TEFC 5 1800 230/460 PE CT 2:1 yes 184TC FC00518APJFA $1,283TEFC 5 1800 230/460 EE CT 2:1 yes 184TC FC00518AEJFA 51 $1,035TEFC 7.5 1800 230/460 PE CT 2:1 yes 213TC FC7F518APJFA $1,572TEFC 7.5 1800 230/460 EE CT 2:1 yes 215TC FC7F518AEJFA 51 $1,258TEFC 10 1800 230/460 PE CT 2:1 yes 215TC FC01018APJFA $1,756TEFC 10 1800 230/460 EE CT 2:1 yes 215TC FC01018AEJFA 51 $1,400



60

General

Information

CM

100C

M 200

CM

300F

ootnotes



Delivery Cycle





SPACE HEATERS: 180 Addition of 120V single phase, 60 Hz space heater, aux CB not included 48, 56, 140 $359

180-280 $419320-400 $470

440-L449 $589




61

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Component ClassInverter Duty Harsh Environment SeriesCM118 Family - Stainless Steel AC Motors






Application InformationFor use in severe applications where chemicals will degrade the motor surface.

EE (24 / 12)


56 - 140T FramesMaterials: Stainless steel frame, end shields, conduit box and fan cover

Conduit Box: Oversized, top mounted with F1 and F2 lead outlets, water tight connector

Bearing Type: Double sealed ball bearings.

Bearing Protection: Stainless lip seal on both ends and drive end shaft slinger.

Shaft Material: 300 series stainless steel

Nameplate Material: Stainless Steel

Drain Type & Location:

Stainless T-drains every 90 degrees.

Additional Features: “Paint free”Water tight connector for leads.Insulation system exceeds NEMA MG1 Part 31.4.4.2 requirements by staying corona free at up to 1600V peaks, and 10,000V/µSec dV/dT.

CM118 Family - Stainless Steel AC Motors

62

General

Information

CM

100C

M 200

CM

300F

ootnotes

Component Class, Inverter Duty Harsh Environment SeriesCM118 Family - Stainless Steel AC Motors


RPM Class Torque/Spd Stock CM118- PriceTENV 0.5 1800 208-230/460 EE CT 4:1 N 56 NV0F518GEKHA 15 $770TENV 0.75 1800 208-230/460 EE CT 4:1 N 56 NVF7518GEKHA 15 $794TENV 1 1800 208-230/460 EE CT 4:1 N 143T NV00118GEKHA 15 $812TEFC 1.5 1800 208-230/460 EE CT 4:1 N 145T FC1F518GEKHA 15 $828TEFC 2 1800 208-230/460 EE CT 4:1 N 145T FC00218GEKHA 15 $987


C Face Foot Mounted IP55Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Notes US List

RPM Class Torque/Spd Stock PriceTENV 0.5 3600 208-230/460 EE CT 4:1 N 56C NV0F536GEKCA 15 $741TENV 0.5 1800 208-230/460 EE CT 4:1 N 56C NV0F518GEKCA 15 $788TENV 0.75 3600 208-230/460 EE CT 4:1 N 56C NVF7536GEKCA 15 $763TENV 0.75 1800 208-230/460 EE CT 4:1 N 56C NVF7518GEKCA 15 $812TEFC 1 3600 208-230/460 EE CT 4:1 N 56C FC00136GEKCA 15 $825TENV 1 1800 208-230/460 EE CT 4:1 N 56C NV00118GEKC5A 15 $829TEFC 1 1800 208-230/460 EE CT 4:1 N 56C FC00118GEKCA 15 $829TENV 1 1800 208-230/460 EE CT 4:1 N 143TC NV00118GEKC4A 15 $830TEFC 1.5 3600 208-230/460 EE CT 4:1 N 56C FC1F536GEKC5A 15 $833TEFC 1.5 3600 208-230/460 EE CT 4:1 N 145TC FC1F536GEKC4A 15 $834TEFC 1.5 1800 208-230/460 EE CT 4:1 N 145TC FC1F518GEKC4A 15 $845TEFC 1.5 1800 208-230/460 EE CT 4:1 N 56C FC1F518GEKC5A 15 $846TEFC 2 3600 208-230/460 EE CT 4:1 N 56C FC00236GEKC5A 15 $994TEFC 2 3600 208-230/460 EE CT 4:1 N 145TC FC00236GEKC4A 15 $995TEFC 2 1800 208-230/460 EE CT 4:1 N 56C FC00218GEKC5A 15 $1,003TEFC 2 1800 208-230/460 EE CT 4:1 N 145TC FC00218GEKC4A 15 $1,004TEFC 3 3600 208-230/460 EE CT 4:1 N 145TC FC00336GEKCA 15 $1,175TEFC 3 1800 208-230/460 EE CT 4:1 N 145TC FC00318GEKCA 15 $1,108


C Face Footless IP55Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Notes US List

RPM Class Torque/Spd Stock PriceTENV 0.5 3600 208-230/460 EE CT 4:1 N 56C NV0F536GEKFA 15 $727TENV 0.5 1800 208-230/460 EE CT 4:1 N 56C NV0F518GEKFA 15 $773TENV 0.75 3600 208-230/460 EE CT 4:1 N 56C NVF7536GEKFA 15 $749TENV 0.75 1800 208-230/460 EE CT 4:1 N 56C NVF7518GEKFA 15 $797TEFC 1 3600 208-230/460 EE CT 4:1 N 56C FC00136GEKFA 15 $812TENV 1 1800 208-230/460 EE CT 4:1 N 56C NV00118GEKF5A 15 $814TENV 1 1800 208-230/460 EE CT 4:1 N 143TC NV00118GEKF4A 15 $815TEFC 1.5 3600 208-230/460 EE CT 4:1 N 145TC FC1F536GEKFA 15 $819TEFC 1.5 1800 208-230/460 EE CT 4:1 N 145TC FC1F518GEKFA 15 $832TEFC 2 3600 208-230/460 EE CT 4:1 N 145TC FC00236GEKFA 15 $980TEFC 2 1800 208-230/460 EE CT 4:1 N 145TC FC00218GEKFA 15 $990TEFC 3 3600 208-230/460 EE CT 4:1 N 145TC FC00336GEKFA 15 $1,161TEFC 3 1800 208-230/460 EE CT 4:1 N 145TC FC00318GEKFA 15 $1,085



63

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es



Delivery Cycle



No Modifications available for Stainless Steel Motors

THERMAL PROTECTION: Addition of thermostats.159 Standard in Component Class Motors All incl160 Removal of standard thermostats from motor (deduct from List Price) 48-280 -$208





64

General

Information

CM

100C

M 200

CM

300F

ootnotes

Accessory Kits for CM100-300 Motors

AdaptersFrame Approximate AB Model AB List Normally

Weight (lb) Number Price Stocked182-143T 3 CMKIT-602123-2A $81 Yes184-145T 3 CMKIT-602123-2A $81 Yes213-182T 3 CMKIT-42384-17-A $152 Yes215-184T 3 CMKIT-42384-17-A $152 Yes

254U-213T 6 CMKIT-42384-17-B $152 Yes256U-215T 6 CMKIT-42384-17-B $152 Yes284U-254T 7 CMKIT-42384-17-C $152 Yes286U-256T 7 CMKIT-42384-17-C $152 Yes324U-284T 11 CMKIT-42384-17-D $195 Yes326U-286T 10 CMKIT-42384-17-D $195 Yes

326U-284TS 10 CMKIT-42384-17-G $257 Yes364U-324TS 14 CMKIT-42384-17-E $334 Yes365U-326T 15 CMKIT-42384-17-E $334 Yes404U-364T 20 CMKIT-42384-17-P $343 Yes

404US-364TS 21 CMKIT-42384-17-R $397 Yes405U-365T 21 CMKIT-42384-17-P $343 Yes

404US-364TS 21 CMKIT-42384-17-R $397 Yes444U-364T 95 CMKIT-42384-17-S $526 No445U-365T 95 CMKIT-42384-17-S $526 No

Discount Schedule 16

CM100 Family - Accessory Kits

65

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

BrakesFrame Type Enclosure Approx. AB Model AB List Notes Norm.

Wt (lb) Number Price Stock56, 140, 180 Brake Fast Response All 1 CMKIT-031425 $102 230/460 Yes56, 140, 180 Brake Fast Response All 1 CMKIT-031386 $91 115/230 Yes56, 140, 180 Brake Rectifier All 1 CMKIT-024018 $64 both DBSC & DBSS Yes



BasesFrame Approximate AB Model AB List Notes Norm.

Weight Number Price Stocked56 5 CMKIT-413330-10F $47 Yes

143T 6 CMKIT-79068-24A $81 Yes145T 6 CMKIT-79068-24B $81 Yes

182T, U 9 CMKIT-42384-U $99 Yes184T, U 10 CMKIT-42384-V $99 Yes213T, U 15 CMKIT-42384-W $111 Yes215T, U 16 CMKIT-42384-X $111 Yes254T, U 18 CMKIT-42384-D $163 Yes254T, U 20 CMKIT-42384-4E $201 21 Yes256T, U 22 CMKIT-42384-Y $163 Yes256T, U 22 CMKIT-42384-4P $201 21 Yes284T, U 27 CMKIT-42384-E $195 0 Yes284T, U 27 CMKIT-42384-4M $223 21 Yes286T, U 22 CMKIT-42384-Z $195 Yes286T, U 25 CMKIT-42384-4T $223 21 Yes324T, U 37 CMKIT-42384-F $267 Yes324T, U 40 CMKIT-42384-4R $296 21 Yes326T U 32 CMKIT-42384-G $267 Yes326T U 37 CMKIT-42384-4D $296 21 Yes364T, U 49 CMKIT-42384-H $347 Yes364T, U 49 CMKIT-42384-4U $373 21 Yes365T, U 45 CMKIT-42384-J $347 Yes365T, U 49 CMKIT-42384-4V $373 21 Yes404T, U 60 CMKIT-42384-K $699 Yes404T, U 55 CMKIT-42384-4F $699 21 Yes405T, U 61 CMKIT-42384-L $699 Yes405T, U 65 CMKIT-42384-4G $699 21 Yes444T, U 83 CMKIT-42384-M $776 Yes444T, U 74 CMKIT-42384-4H $776 21 Yes445T, U 85 CMKIT-42384-N $776 Yes445T, U 75 CMKIT-42384-4J $776 21,22 Yes447/9T 102 CMKIT-702694-3R $3,228 23 Yes



66

General

Information

CM

100C

M 200

CM

300F

ootnotes


C-FaceFrame Type Enclosure Approx. AB Model AB List Notes Norm.

Wt (lb) Number Price Stock 56 # C-Face Kit Basic (TEFC, TENV) 2 CMKIT-K56H3055 $35 28 Yes

56, 140 ## C-Face Kit Basic (TEFC, TENV) 3 CMKIT-K56H3063 $35 29 Yes180T C-Face Kit TEFC 5 CMKIT-K18G3 $146 3,12 Yes180T C-Face Kit TEFC 5 CMKIT-K18G32 $146 12 Yes180T C-Face Kit ODP 3 CMKIT-K18S33 $146 12 Yes180T C-Face Kit TEFC 3 CMKIT-K18S34 $146 12 Yes180 C-Face Kit TEFC U-FRAME 10 CMKIT-K18G5 $146 3,12 Yes

210T, U C-Face Kit TEFC 18 CMKIT-K21G3 $146 3,12 Yes210T, U C-Face Kit TEFC 10 CMKIT-K21G32 $146 12 Yes210T, U C-Face Kit ODP 7 CMKIT-K21S33 * $146 12 Yes210T, U C-Face Kit ODP 7 CMKIT-K21S35 ** $146 12 Yes210T, U C-Face Kit TEFC 7 CMKIT-K21S34 $146 12 Yes250T, U C-Face Kit TEFC 25 CMKIT-K25G2 $190 3,12 Yes250T, U C-Face Kit TEFC 18 CMKIT-K25G32 $190 12 Yes250T, U C-Face Kit ODP 15 CMKIT-K25S33 $190 12 Yes250T, U C-Face Kit TEFC 15 CMKIT-K25S34 $190 12 Yes280T, U C-Face Kit TEFC 32 CMKIT-K28G2 $270 3,12 Yes280T, U C-Face Kit TEFC 25 CMKIT-K28G32 $270 12 Yes280T, U C-Face Kit ODP 22 CMKIT-K28S33 $270 12 Yes280T, U C-Face Kit TEFC 22 CMKIT-K28S34 $270 12 Yes320T, U C-Face Kit TEFC 34 CMKIT-K32G2 $417 3,12 Yes320T, U C-Face Kit TEFC 57 CMKIT-K32G32 $406 12 Yes360T, U C-Face Kit TEFC 40 CMKIT-K36G2 $594 3,12 Yes360T, U C-Face Kit TEFC 40 CMKIT-K36G32 * $594 12 Yes360T, U C-Face Kit TEFC 40 CMKIT-K36G35 ** $594 12 Yes400T, U C-Face Kit TEFC 46 CMKIT-K40G2 $891 3,73 Yes


D FlangeFrame Type Enclosure prox. Wt ( AB Model AB List Notes Norm.

Number Price Stock180, 180T D-Flange Kit TEFC 10 CMKIT-K18G6 $264 3,47 No210, 210T D-Flange Kit TEFC 15 CMKIT-K21G6 $323 3,47 No


# For frames beginning with E ; ie, EB56## For frames beginning with F ;ie, FB56* 1200 RPM ** 3600 RPM

(1) Basic (TEFC, TENV) motors that have aluminum end shields. This kit will not mount on XT/EMT/XEX and other enhanced enclosure product that have Cast Iron end shields


67

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Conduit BoxesFrame Type Enclosure Conduit Box Approx. AB Model AB List Notes Norm.

Material Wt (lb) Number Price Stock48, 56 Conduit Box Kit XP Aluminum 1 CMKIT-K48H3240 $46 28 Yes

56 - 140T Conduit Box Kit XP Aluminum 1 CMKIT-K56G3230 $36 29 Yes56 - 140T Conduit Box Kit XP-XT Cast Iron 1 CMKIT-K56H3260 $91 29 Yes56 - 140T Conduit Box Kit ODP/TENV Steel 1 CMKIT-K56H3250 $21 29 Yes

180T Conduit Box Kit TEFC Cast Iron 3 CMKIT-K18G7 $54 3 Yes210T Conduit Box Kit TEFC Cast Iron 3 CMKIT-K21G7 $54 3 Yes250T Conduit Box Kit TEFC Cast Iron 6 CMKIT-K25G8 $72 3 Yes280T Conduit Box Kit TEFC Cast Iron 10 CMKIT-K28G8 $72 3 Yes320T Conduit Box Kit TEFC Cast Iron 15 CMKIT-K32G8 $144 3 Yes360T Conduit Box Kit TEFC Cast Iron 20 CMKIT-K36G8 $144 3 Yes

180/210 Auxiliary Conduit Box Kits TEFC-Severe Duty Cast Iron 4 CMKIT-K18G21 $64 Yes250 Auxiliary Conduit Box Kits TEFC-Severe Duty Cast Iron 9 CMKIT-K25G23 $70 Yes280 Auxiliary Conduit Box Kits TEFC-Severe Duty Cast Iron 9 CMKIT-K28G23 $82 Yes320 Auxiliary Conduit Box Kits TEFC-Severe Duty Cast Iron 9 CMKIT-K32G23 $88 Yes360 Auxiliary Conduit Box Kits TEFC-Severe Duty Cast Iron 12 CMKIT-K36G16 $163 Yes400 Auxiliary Conduit Box Kits TEFC-Severe Duty Cast Iron 15 CMKIT-K40G3 $175 Yes440 Auxiliary Conduit Box Kits TEFC-Severe Duty Cast Iron 18 CMKIT-K44G5 $373 Yes


Documentation for Control Matched Motors

DocumentationAB Model AB List Typical Number Description Price Lead Time

CMKIT-MTRCERT Motor Certified Drawings 50$ 4-6 weeksCMKIT-MTRMFG Typical Dimension Drawing -$ Varies

CMKIT-MTRACAD Motor Dimension Drawings in Autocad 150$ Upon shipment of

motorCMKIT-MTRAPP Motor Approval Drawings -$ 4-6 weeks

CMKIT-MTRSTDPD Motor Standard Tabulated Performance Data 60$ 4-6 weeks

CMKIT-MTRLIST Motor Spare Parts List 15$ Upon shipment of

motor

CMKIT-MTRRTEST Motor Unwitness Routine Test and Report 125$ Upon shipment of

motorDiscount schedule 16


68

General

Information

CM

100C

M 200

CM

300F

ootnotes


Drip Covers/ Canopy KitFrame Type Enclosure Approx. AB Model AB List Notes Norm.

Wt (lb) Number Price Stock56, 140T Drip Cover / Canopy Kit TEFC, XT, XP 1 CMKIT-K56H3008 $50 29 Yes

180T Drip Cover / Canopy Kit TEFC 12 CMKIT-K18G2 $96 Yes180T Drip Cover / Canopy Kit TEFC 8 CMKIT-K18G19 $96 Yes180T Drip Cover / Canopy Kit TEFC 6 CMKIT-K18S30 $96 Yes210T Drip Cover / Canopy Kit TEFC 18 CMKIT-K21G2 $120 Yes210T Drip Cover / Canopy Kit TEFC 10 CMKIT-K21G19 $120 Yes210T Drip Cover / Canopy Kit TEFC 8 CMKIT-K21S30 $120 Yes250T Drip Cover / Canopy Kit TEFC 12 CMKIT-K25S30 $180 Yes280T Drip Cover / Canopy Kit TEFC 18 CMKIT-K28S30 $251 Yes



Mill and Chemical Duty Kit Cast Iron Shroud and Conduit BoxFrame Type Enclosure Approx. Wt (lb) AB Model AB List Norm.

Number Price Stock180T Cast Iron TEFC 12 CMKIT-K18G18 $174 Yes210T Cast Iron TEFC 15 CMKIT-K21G18 $239 Yes250T Cast Iron TEFC 20 CMKIT-K25G18 $323 Yes280T Cast Iron TEFC 25 CMKIT-K28G18 $383 Yes320T Cast Iron TEFC 30 CMKIT-K32G18 $419 Yes364T Cast Iron TEFC CMKIT-K36G18 $677 No



69

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Motor BrakesFrame Enclosure Type Supply Aprx. Unt. Size AB Model AB List

Voltage Wt. Stat.Torque Number Price56 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 3 Ft- Lbs CMKIT-31369 $59056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 6 Ft- Lbs CMKIT-31411 $63556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 10 Ft - Lbs CMKIT-31453 $71756 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 15 Ft- Lbs CMKIT-31342 $82556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 20 Ft- Lbs CMKIT-31345 $1,10056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 25 Ft- Lbs CMKIT-31348 $1,32956 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 3 Ft- Lbs CMKIT-31371 $59056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 6 Ft- Lbs CMKIT-31413 $63556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 10 Ft - Lbs CMKIT-31455 $71756 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 15 Ft- Lbs CMKIT-31343 $82556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 20 Ft- Lbs CMKIT-31346 $1,10056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 25 Ft- Lbs CMKIT-31349 $1,32956 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 3 Ft- Lbs CMKIT-31373 $59056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 6 Ft- Lbs CMKIT-31415 $63556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 10 Ft - Lbs CMKIT-31457 $71756 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 15 Ft- Lbs CMKIT-31344 $82556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 20 Ft- Lbs CMKIT-31347 $1,10056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 25 Ft- Lbs CMKIT-31350 $1,32956 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 3 Ft- Lbs CMKIT-31088 $59056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 6 Ft- Lbs CMKIT-31100 $63556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 10 Ft - Lbs CMKIT-31112 $71756 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 15 Ft- Lbs CMKIT-31124 $82556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 20 Ft- Lbs CMKIT-31136 $1,10056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 25 Ft- Lbs CMKIT-31148 $1,32956 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 3 Ft- Lbs CMKIT-31089 $59056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 6 Ft- Lbs CMKIT-31101 $63556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 10 Ft - Lbs CMKIT-31113 $71756 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 15 Ft- Lbs CMKIT-31125 $82556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 20 Ft- Lbs CMKIT-31137 $1,10056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 25 Ft- Lbs CMKIT-31149 $1,32956 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 3 Ft- Lbs CMKIT-31090 $59056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 6 Ft- Lbs CMKIT-31102 $63556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 10 Ft - Lbs CMKIT-31114 $71756 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 15 Ft- Lbs CMKIT-31126 $82556 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 20 Ft- Lbs CMKIT-31138 $1,10056 Frame 5/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 25 Ft- Lbs CMKIT-31150 $1,329




70

General

Information

CM

100C

M 200

CM

300F

ootnotes


Voltage Wt. Stat.Torque Number Price140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 3 Ft- Lbs CMKIT-31375 $590140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 6 Ft- Lbs CMKIT-31417 $635140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 10 Ft - Lbs CMKIT-31459 $717140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 15 Ft- Lbs CMKIT-31495 $825140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 20 Ft- Lbs CMKIT-31525 $1,100140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (1) 13 25 Ft- Lbs CMKIT-31555 $1,329140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 3 Ft- Lbs CMKIT-31377 $590140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 6 Ft- Lbs CMKIT-31419 $635140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 10 Ft - Lbs CMKIT-31461 $717140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 15 Ft- Lbs CMKIT-31497 $825140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 20 Ft- Lbs CMKIT-31527 $1,100140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (2) 13 25 Ft- Lbs CMKIT-31557 $1,329140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 3 Ft- Lbs CMKIT-31379 $590140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 6 Ft- Lbs CMKIT-31421 $635140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 10 Ft - Lbs CMKIT-31463 $717140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 15 Ft- Lbs CMKIT-31499 $825140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 20 Ft- Lbs CMKIT-31529 $1,100140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (3) 13 25 Ft- Lbs CMKIT-31559 $1,329140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 3 Ft- Lbs CMKIT-31094 $590140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 6 Ft- Lbs CMKIT-31106 $635140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 10 Ft - Lbs CMKIT-31118 $717140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 15 Ft- Lbs CMKIT-31130 $825140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 20 Ft- Lbs CMKIT-31142 $1,100140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 104/208 VAC 60 Hz (4) 13 25 Ft- Lbs CMKIT-31154 $1,329140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 3 Ft- Lbs CMKIT-31095 $590140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 6 Ft- Lbs CMKIT-31107 $635140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 10 Ft - Lbs CMKIT-31119 $717140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 15 Ft- Lbs CMKIT-31131 $825140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 20 Ft- Lbs CMKIT-31143 $1,100140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 190/380 VAC 50 Hz (5) 13 25 Ft- Lbs CMKIT-31155 $1,329140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 3 Ft- Lbs CMKIT-31096 $590140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 6 Ft- Lbs CMKIT-31108 $635140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 10 Ft - Lbs CMKIT-31120 $717140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 15 Ft- Lbs CMKIT-31132 $825140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 20 Ft- Lbs CMKIT-31144 $1,100140 Frame 7/8",Bore Standard Enclosure DBSS Complete Uts. 250/500 VAC 50 Hz 13 25 Ft- Lbs CMKIT-31156 $1,329



71

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Voltage Wt. Stat.Torque Number Price56 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 3 Ft- Lbs CMKIT-30381 $91956 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 6 Ft- Lbs CMKIT-30384 $1,10056 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 10 Ft - Lbs CMKIT-30387 $1,21356 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 15 Ft- Lbs CMKIT-30390 $1,32956 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 20 Ft- Lbs CMKIT-30393 $1,47256 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 25 Ft- Lbs CMKIT-30396 $1,73556 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 3 Ft- Lbs CMKIT-30382 $91956 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 6 Ft- Lbs CMKIT-30385 $1,10056 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 10 Ft - Lbs CMKIT-30388 $1,21356 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 15 Ft- Lbs CMKIT-30391 $1,32956 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 20 Ft- Lbs CMKIT-30394 $1,47256 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 25 Ft- Lbs CMKIT-30397 $1,73556 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 3 Ft- Lbs CMKIT-30383 $91956 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 6 Ft- Lbs CMKIT-30386 $1,10056 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 10 Ft - Lbs CMKIT-30389 $1,21356 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 15 Ft- Lbs CMKIT-30392 $1,32956 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 20 Ft- Lbs CMKIT-30395 $1,47256 Frame 5/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 25 Ft- Lbs CMKIT-30398 $1,735



Voltage Wt. Stat.Torque Number Price140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 3 Ft- Lbs CMKIT-29400 $919140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 6 Ft- Lbs CMKIT-29403 $1,100140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 10 Ft - Lbs CMKIT-29406 $1,213140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 15 Ft- Lbs CMKIT-29409 $1,329140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 20 Ft- Lbs CMKIT-29412 $1,472140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 115/230 VAC 60 Hz (6) 14 25 Ft- Lbs CMKIT-29415 $1,735140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 3 Ft- Lbs CMKIT-29401 $919140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 6 Ft- Lbs CMKIT-29404 $1,100140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 10 Ft - Lbs CMKIT-29407 $1,213140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 15 Ft- Lbs CMKIT-29410 $1,329140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 20 Ft- Lbs CMKIT-29413 $1,472140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 230/460 VAC 60 HZ (7) 14 25 Ft- Lbs CMKIT-29416 $1,735140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 3 Ft- Lbs CMKIT-29402 $919140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 6 Ft- Lbs CMKIT-29405 $1,100140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 10 Ft - Lbs CMKIT-29408 $1,213140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 15 Ft- Lbs CMKIT-29411 $1,329140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 20 Ft- Lbs CMKIT-29414 $1,472140 Frame 7/8",Bore E-Z KLEEN Enclosure DBSS Complete Uts. 287/575 VAC 60 Hz (8) 14 25 Ft- Lbs CMKIT-29417 $1,735


NOTES:Bold Part Numbers are stock units. Other voltage units available on standard non-stock basis.Coil will operate at the following voltages:*All torque ratings and voltages not listed here are available as standard non-stock units. Please contact DODGE Customer Service for part numbers, pricing & availability.

(1) 15/208-230 VAC 50 or 60 Hz,133/265 VAC 60 Hz, 110-125 VDC(2) 08-230/460 VAC 50 or 60 Hz, 240/480 VAC 60 Hz, 220/440 VAC 50 Hz, 230 VDC(3) 287/575 VAC 60 Hz, 300/600 VAC 60 Hz(4) 104/208 VAC 50 or 60 Hz, 100/200 VAC 60 Hz, 90-95 VDC(5) 190/380 VAC 50 Hz, 200/400 VAC 60 Hz, 206/416 VAC 50 Hz(6) 115/208-230 VAC 50 or 60 Hz,133/265 VAC 60 Hz, 110-125 VDC(7) 208-230/460 VAC 50 or 60 Hz, 240/480 VAC 60 Hz, 220/440 VAC 50 Hz, 230 VDC(8) 287/575 VAC 60 Hz, 275/550 VAC 60 Hz, 300/600 VAC 60 Hz

·Coil will operate at the following voltages:


72

General

Information

CM

100C

M 200

CM

300F

ootnotes


CM200 Family

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Architecture ClassIndustrial Environment SeriesCM201 Family - Vector Duty Enclosed Small AC Motors



Frequency: 60 Hz Duty Cycle: Continuous These motors have a special inverter duty design not covered by EPAct efficiency levels

Ambient: 40° C Insulation: Class FService Factor: 1.0 Temp. Rise: Class B

Max RPM: 6000 Warranty (From Date Of Manufacture /


Application InformationFor variable speed 1000:1 constant torque applications

(24 / 12)


56 - 180T Frames IP44Materials: Steel frame and conduit box (56 frames). Aluminum frame and

conduit box (140 - 180 frames). End shields are aluminum.

Conduit Box: Oversized, top mounted with F1 & F2 lead outlets

Bearing Type: Double shielded ball

Bearing Protection: None


Nameplate Material: Adhesive Mylar

Drain Type & Location: Weep holes on both end shields

Additional Features: Includes 3 NC thermostats

CM201 Family - Vector Duty Enclosed Small AC Motors

73

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Architecture Class, Industrial Environment SeriesCM201 - Vector Duty Enclosed Small AC Motors

C-Face Foot Mounted 230/460V IP44Enclosure HP Speed- RPM Voltage Inverter Norm. Frame 460V US List Catalog String Notes

Base CHP Torque/Spd Stock Amps Price CM201-TENV 0.33 3600 5400 230/460 CT 1000:1 No FB56C 0.8 $372 NVF3336AXZCA 59TENV 0.33 1800 3600 230/460 CT 1000:1 Yes FB56C 0.5 $379 NVF3318AXZCA 59TENV 0.33 1200 2400 230/460 CT 1000:1 No FB56C 0.7 $472 NVF3312AXZCA 59TENV 0.5 3600 5400 230/460 CT 1000:1 No FB56C 0.8 $423 NV0F536AXZCA 59TENV 0.5 1800 3600 230/460 CT 1000:1 Yes FB56C 0.8 $433 NV0F518AXZCA 59TENV 0.5 1200 2400 230/460 CT 1000:1 No FB56C 1 $498 NV0F512AXZCA 59TENV 0.75 3600 5400 230/460 CT 1000:1 No FB56C 1.1 $475 NVF7536AXZCA 59TENV 0.75 1800 3600 230/460 CT 1000:1 Yes FB56C 1.1 $488 NVF7518AXZCA 59TENV 0.75 1200 2400 230/460 CT 1000:1 No FC56C 1.5 $520 NVF7512AXZCA 59TENV 1 3600 5400 230/460 CT 1000:1 No WC143TC 1.2 $559 NV00136AXZCA 59TENV 1 1800 3600 230/460 CT 1000:1 Yes WC143TC 1.6 $498 NV00118AXZCA 59TENV 1 1200 2400 230/460 CT 1000:1 No WC143TC 1.8 $585 NV00112AXZCA 59TENV 1.5 3600 5400 230/460 CT 1000:1 No WC143TC 2 $715 NV1F536AXZCA 59TENV 1.5 1800 3600 230/460 CT 1000:1 Yes WC145TC 2.3 $520 NV1F518AXZCA 59TENV 1.5 1200 2400 230/460 CT 1000:1 No WE145TC 2.2 $693 NV1F512AXZCA 59TENV 2 3600 5400 230/460 CT 1000:1 No WD145TC 2.5 $748 NV00236AXZCA 59TENV 2 1800 3600 230/460 CT 1000:1 Yes WD145TC 3 $685 NV00218AXZCA 59TENV 3 3600 5400 230/460 CT 1000:1 No WE182TC 3.8 $823 NV00336AXZCA 59TENV 3 1800 3600 230/460 CT 1000:1 Yes WE182TC 4.4 $797 NV00318AXZCA 59TEBC 5 3600 5400 230/460 CT 1000:1 No WE184TC 5.9 $1,008 BC00536AXZCA 59TEBC 5 1800 3600 230/460 CT 1000:1 Yes WE184TC 7.1 $953 BC00518AXZCA 59


C-Face Foot Mounted 575V IP44Enclosure HP Speed- RPM Voltage Inverter Norm. Frame 575V US List Catalog String Notes

Base CHP Torque/Spd Stock Amps Price CM201-TENV 0.33 3600 5400 575 CT 1000:1 No FB56C 0.6 $372 NVF3336CXZCA 59TENV 0.33 1800 3600 575 CT 1000:1 No FB56C 0.4 $379 NVF3318CXZCA 59TENV 0.33 1200 2400 575 CT 1000:1 No FB56C 0.6 $472 NVF3312CXZCA 59TENV 0.5 3600 5400 575 CT 1000:1 No FB56C 0.6 $423 NV0F536CXZCA 59TENV 0.5 1800 3600 575 CT 1000:1 No FB56C 0.6 $433 NV0F518CXZCA 59TENV 0.5 1200 2400 575 CT 1000:1 No FB56C 0.8 $498 NV0F512CXZCA 59TENV 0.75 3600 5400 575 CT 1000:1 No FB56C 0.9 $475 NVF7536CXZCA 59TENV 0.75 1800 3600 575 CT 1000:1 No FB56C 0.9 $488 NVF7518CXZCA 59TENV 0.75 1200 2400 575 CT 1000:1 No FC56C 1.2 $520 NVF7512CXZCA 59TENV 1 3600 5400 575 CT 1000:1 No WC143TC 1.0 $559 NV00136CXZCA 59TENV 1 1800 3600 575 CT 1000:1 No WC143TC 1.3 $498 NV00118CXZCA 59TENV 1 1200 2400 575 CT 1000:1 No WC143TC 1.4 $585 NV00112CXZCA 59TENV 1.5 3600 5400 575 CT 1000:1 No WC143TC 1.6 $715 NV1F536CXZCA 59TENV 1.5 1800 3600 575 CT 1000:1 No WC145TC 1.8 $520 NV1F518CXZCA 59TENV 1.5 1200 2400 575 CT 1000:1 No WE145TC 1.8 $693 NV1F512CXZCA 59TENV 2 3600 5400 575 CT 1000:1 No WD145TC 2.0 $748 NV00236CXZCA 59TENV 2 1800 3600 575 CT 1000:1 No WD145TC 2.4 $685 NV00218CXZCA 59TENV 3 3600 5400 575 CT 1000:1 No WE182TC 3.0 $823 NV00336CXZCA 59TENV 3 1800 3600 575 CT 1000:1 No WE182TC 3.5 $797 NV00318CXZCA 59TEBC 5 3600 5400 575 CT 1000:1 No WE184TC 4.7 $1,008 BC00536CXZCA 59TEBC 5 1800 3600 575 CT 1000:1 No WE184TC 5.7 $953 BC00518CXZCA 59



74

General

Information

CM

100C

M 200

CM

300F

ootnotes


Lead Time


US ListCode Modification Description Frame Enclosure Price Notes

BEARINGS: (per set / per motor)Note: Bearing manufacturer is RA option.

303 Sealed bearings-convert to permanently lubricated sealed bearings ALL ALL $286 100BRAKES:Mount double c-face DODGE DBSS brake kit to Drive End of C-Face motor

306 3 ft. lb. 56C. 140TC TENV $1,378307 6 ft. lb. 56C. 140TC TENV $1,429308 10 ft. lb. 56C. 140TC TENV $1,511309 15 ft. lb. 56C. 140TC TENV $1,593310 20 ft. lb. 56C. 140TC TENV $1,766311 25 ft. lb. 56C. 140TC TENV $1,940

CONDUIT BOX: Mounting of stock box kits (price includes box):316 Drill drain hole ALL ALL $214

CONNECTIONS:319 Final connect dual to single voltage. ALL ALL $153

FEEDBACK DEVICE:Mounting of stock encoder kits. Price includes all material and labor to mountencoder on Opposite Drive End of motor.

334 Dynapar HS20, 5-26 vdc supply, single output, 1024 ppr w/ marker pulse 56,140,W*180 TENV $817335 Dynapar HS20, 5-26 vdc supply, single output, 1024 ppr w/ marker pulse W*180 TEBC $1,225336 Lakeshore SL56, 5-15 vdc supply, single output, 1024 ppr 56,140,W*180 TENV $1,531

GROUNDING: (All motors have provision for grounding)361 Clamp type in conduit box ALL ALL $214

INSULATION: Tropical protection364 Addition of anti-fungus treatment to windings. ALL ALL $286

LEAD TERMINALS: Additon of lead terminals to wires in conduit box.367 Addition of eyelet - type lead terminals 56 - 140 ALL $286368 Compression type (Burndy, etc.) lead lugs ALL ALL $357

SEALS: Addition of shaft seal.377 V-ring rubber slinger on drive end ALL ALL $286

Any MOD order cancelled before modification is completed is subject to minimum $100 net cancellation charge. To cancel an order for a motor after it is modified, but before it ships - a cancellation charge of double the modification charge (minimum $100 net) will be invoiced to the customer.

The lead time will be subject to the availability of stock motors and parts. The Modification Center is designed to process and ship units as quickly as possible; therefore, “Hold for Approval” and other similar conditions are not available on Modification Center orders. Typically, modifications will require 1 to 4 business days, once the order is entered. Orders for more than 5 units may require additional delivery time. The lead time shown on a Passport screen is for the base motor only, modifications will add to actual lead time.

Changes to an OrderGeneral InformationModifications Available to CM201 Motors


75

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Architecture ClassIndustrial Environment SeriesCM202 Family - Vector Duty Enclosed NEMA Frame AC Motors

The CM202 motor was designed from the beginning to be a Variable Speed Vector Inverter Duty motor. It is not a fixed speed motor design that has been re-rated to be an Inverter Duty motor. All CM202 motors are designed to operate from zero speed to base speed with full load current and torque below the class F temperature rise. Each CM202 has three thermostats, one per phase, to provide Inverter Duty thermal protection. The CM202 1800 rpm, 1200 rpm and 900 rpm motors truly provide the performance of a blower-cooled motor in a TEFC enclosure. This means that the

motor.

CM202 Features• All CM202 Family motors are Totally Enclosed, and have an ingress protection rating of IP44 for use in industrial

environments.

• Ambient: 40° C

• Altitude: 3300 ft (1000m) Above Sea Level

• 1000:1 Constant Torque - This means that the CM202 Family motors are designed to operate from zero to base speed continuously with full load current and torque. The CM202 Family motors are designed to draw nameplate current

bility 1000:1 Constant Torque. Some manufacturers identify this capability 1000:1 Constant Torque, some manufac-tures identify this capability as 2000:1, 3000:1, infinity:1, etc. All of these terms describe the same capability of the AC Motor, one is not better than another.

• 200% Overload Torque - Each CM202 Family motor has an electrical design that will provide 200% overload torque for one minute from zero to base speed.

• Constant Horsepower - The standard CM202 Family motor is designed to provide constant horsepower to 1.5 times base speed.

• Continuous Duty - Contact Rockwell Automation for different duty cycles

• 1.0 Service Factor - Because CM202 Family motors are designed for Inverter Duty applications, not across-the-line designs, all designs have a 1.0 SF as standard on inverter power.

• Standard NEMA T Frames - CM202 Family motors, 2 HP to 500 HP are all in standard NEMA frames (Larger motors are in above NEMA frames 447T through L449T).

• Cast Iron Frames - All CM202 Family motors are in cast iron frames with cast iron end shields.

• F1 Mounting - Conduit box location is F1 as standard on NEMA frame motors. F2 or top mounted conduit boxes are available as a modification.

• Thermostats - Each CM202 Family motor has three normally closed thermostats connected in series, one in each phase of the motor. One set of P1 and P2 leads is brought to the conduit box. If any of the thermostats opens, the P1 and P2 circuit opens.

General Product Description

CM202 Family - Vector Duty Enclosed NEMA Frame AC Motors

76

General

Information

CM

100C

M 200

CM

300F

ootnotes

continuously at zero speed without exceeding the class F temperature rise. The industry standard is to call this capa-

customer does not need to purchase and mount a blower motor starter or install three-phase power leads to the blower


• Encoder Provisions - Each CM202 Family motor has encoder provisions as a standard feature, even if an encoder is not ordered with the motor.

• Insulated Bearing - Every 440 frame (444T through L449T) has an opposite drive end insulated bearing as standard to reduce the chances of the bearings being damaged by shaft currents. In large motors (440 frames) it is quite common to have shaft currents

• Re-greaseable bearings - For longest life in industrial applications, all CM202 Family motors have re-greaseable bearings.

• Stainless Steel Nameplates - Every CM202 Family motor has a stainless steel nameplate with the electrical design number, magnetizing current, constant torque speed range, number of poles, rotor inertia, bearing numbers and other NEMA data.

• Corona Free Insulation - Every CM202 Family motor has Rockwell Automation's “Corona Free” insulation system that exceeds the insulation requirements described in NEMA MG1-2003, part 31, for Definite Purpose, Inverter-Fed Polyphase motors.

• Class F Insulation - CM202 Family motors have a class F insulation system and operate below class F temperature rise. Nearly all TEFC CM202 Family motors operate with a class B rise over a 4:1 speed range. That means that most TEFC 1800-rpm motors will operate with a class B rise over a 450 rpm to 1800 rpm (covers most actual operating conditions) speed range.

Optimum Pole ConfigurationRockwell Automation’s Inverter Duty Motors are based on the use of “optimum pole” design. Unlike fixed speed motors, Inverter-Fed motors can have different base speeds based on different base frequencies. For example, a four-pole motor designed with a base frequency of 40 hertz and a base voltage of 460 vac will have a base synchronous speed of 1200 rpm.

Rockwell Automation selects the number of poles to be used on a Vector Duty motor so that the torque density, speed range, efficiency, power factor, overload capability and acoustic noise can be optimized. Like the Vector Duty CM203 Family motor, most of the Vector Duty CM202 Family motors in frames 180T through 400T are four-pole designs, regardless of the base speed. The Inverter is set to match the motor nameplate, for example, 50 hp, 1200 rpm, 460 vac, 40 hertz, and 4 poles. On larger frames of Vector Duty AC motors, many of the designs are six-pole, regardless of the base speed.

This approach has also been used in DC Motor designs for years. Most of the DC motor ratings 500 hp and less are four-pole designs, regardless of the base speed.

CM202 Family motors are CSA, Canadian Standards Association, certified and carry the monogram on the nameplate. All accessories attached the motor must also carry their own CSA mark. Rockwell Automation’s file number for CM202 Family motors is, LR7861.

The European Committee for Electrotechnical Standardization defines compliance standards for the CE mark required on motors shipping to Europe. It is available upon request on all CM202 Family motors.

CM202 Family motors carry the Underwriters’ Laboratories, Inc., Recognized Component mark for electric motors used in ordinary locations (not explosion-proof). Rockwell Automation’s file number for CM202 Family motors is, E54825.


77

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Architecture Class, Industrial Environment SeriesCM202 - Vector Duty Enclosed NEMA Frame AC Motors

Foot Mounted & C-Face Foot Mounted 230/460V & 460V IP44Enclosure HP Speed- RPM Voltage Inverter Norm. Frame 460V US List Catalog String Notes

Base CHP Torque/Spd Stock Amps Price CM202-TENV 2 1200 1800 230/460 CT 1000:1 Yes 184TC 2.6 $1,204 NV00212AXZCATEFC 2 1200 1800 230/460 CT 1000:1 Yes 182TC 3.2 $1,204 FC00212AXZCATENV 3 1800 2700 230/460 CT 1000:1 Yes 182TC 3.8 $966 NV00318AXZCATEFC 3 1800 2700 230/460 CT 1000:1 Yes 182TC 4.6 $966 FC00318AXZCATEFC 3 1200 1800 230/460 CT 1000:1 No 213TC 4.8 $1,515 FC00312AXZCATENV 3 1200 1800 230/460 CT 1000:1 No 215T 3.9 $1,515 NV00312AXZHATENV 5 1800 2700 230/460 CT 1000:1 Yes L184TC 6.4 $1,129 NV00518AXZCATEFC 5 1800 2700 230/460 CT 1000:1 Yes L184TC 7.4 $1,129 FC00518AXZCATEFC 5 1200 1800 230/460 CT 1000:1 No L215TC 7.6 $1,756 FC00512AXZCATENV 5 1200 1800 230/460 CT 1000:1 No L215T 6.8 $1,756 NV00512AXZHATENV 7.5 1800 2700 230/460 CT 1000:1 Yes L215TC 9.2 $1,412 NV7F518AXZCATEFC 7.5 1800 2700 230/460 CT 1000:1 Yes 213TC 10.8 $1,412 FC7F518AXZCATEFC 7.5 1200 1800 230/460 CT 1000:1 No 254T 9.5 $2,215 FC7F512AXZHATENV 10 1800 2700 230/460 CT 1000:1 Yes 254TC 12.7 $1,699 NV01018AXZCATEFC 10 1800 2700 230/460 CT 1000:1 Yes L215TC 12.4 $1,638 FC01018AXZCATEFC 10 1200 1800 230/460 CT 1000:1 No 256T 12.6 $2,509 FC01012AXZHATENV 15 1800 2700 230/460 CT 1000:1 Yes 256TC 18.7 $2,182 NV01518AXZCATEFC 15 1800 2700 230/460 CT 1000:1 Yes 254TC 20.8 $2,182 FC01518AXZCATEFC 15 1200 1800 460 CT 1000:1 No 284T 19.2 $2,963 FC01512BXZHATENV 20 1800 2700 460 CT 1000:1 No 284T 24.3 $2,452 NV02018BXZHATEFC 20 1800 2700 460 CT 1000:1 Yes 256TC 25.5 $2,154 FC02018BXZCATEFC 20 1200 1800 460 CT 1000:1 No 286T 25.3 $3,370 FC02012BXZHATENV 25 1800 2700 460 CT 1000:1 No 324T 30.6 $3,265 NV02518BXZHATEFC 25 1800 2700 460 CT 1000:1 Yes 284TC 31 $2,724 FC02518BXZCATEFC 25 1200 1800 460 CT 1000:1 No 324T 31.6 $4,423 FC02512BXZHATENV 30 1800 2700 460 CT 1000:1 No 326T 36.4 $5,066 NV03018BXZHATEFC 30 1800 2700 460 CT 1000:1 Yes 286T 38.1 $2,872 FC03018BXZHATEFC 30 1200 1800 460 CT 1000:1 No 326T 37.5 $5,413 FC03012BXZHATENV 40 1800 2700 460 CT 1000:1 No 364T 48.1 $6,189 NV04018BXZHATEFC 40 1800 2700 460 CT 1000:1 Yes 324T 49.8 $4,031 FC04018BXZHATEFC 40 1200 1800 460 CT 1000:1 No 364T 50 $6,521 FC04012BXZHATENV 50 1800 2700 460 CT 1000:1 No 404T 57.9 $7,683 NV05018BXZHATEFC 50 1800 2700 460 CT 1000:1 Yes 326T 62.6 $4,927 FC05018BXZHATEFC 50 1200 1800 460 CT 1000:1 No 365T 60.7 $8,078 FC05012BXZHATEFC 60 1800 2700 460 CT 1000:1 Yes 364T 71.4 $6,104 FC06018BXZHATEFC 60 1200 1800 460 CT 1000:1 No 404T 71.1 $9,640 FC06012BXZHATEFC 75 1800 2700 460 CT 1000:1 Yes 365T 89.4 $7,645 FC07518BXZHATEFC 75 1200 1800 460 CT 1000:1 No 405T 85.1 $10,555 FC07512BXZHATEFC 100 1800 2700 460 CT 1000:1 Yes 405T 115.4 $9,882 FC10018BXZHATEFC 100 1200 1800 460 CT 1000:1 No 444T 119 $13,634 FC10012BXZHATEFC 125 1800 2700 460 CT 1000:1 Yes 444T 151 $12,265 FC12518BXZHATEFC 125 1200 1800 460 CT 1000:1 No 445T 151 $15,310 FC12512BXZHATEFC 150 1800 2700 460 CT 1000:1 Yes 445T 177 $14,638 FC15018BXZHATEFC 150 1200 1800 460 CT 1000:1 No 447T 177 $18,887 FC15012BXZHATEFC 200 1800 2700 460 CT 1000:1 Yes 447T 226 $17,344 FC20018BXZHATEFC 200 1200 1800 460 CT 1000:1 No 449T 230 $23,475 FC20012BXZHATEFC 250 1800 2700 460 CT 1000:1 Yes 449T 279 $21,441 FC25018BXZHATEFC 250 1200 1800 460 CT 1000:1 No 449T 290 $27,358 FC25012BXZHA 121TEFC 250 1200 1800 460 CT 1000:1 No L449T 290 $29,400 FC25012BXZHBTEFC 300 1800 2700 460 CT 1000:1 Yes 449T 338 $24,514 FC30018BXZHATEFC 300 1200 1800 460 CT 1000:1 No L449T 354 $36,761 FC30012BXZHATEFC 350 1800 2700 460 CT 1000:1 No L449T 397 $29,411 FC35018BXZHATEFC 400 1800 2700 460 CT 1000:1 No L449T 445 $39,302 FC40018BXZHATEFC 450 1800 2700 460 CT 1000:1 No L449T 501 $47,280 FC45018BXZHATEFC 500 1800 2700 460 CT 4:1 No L449T 551 $48,673 FC50018BXKHA 122



78

General

Information

CM

100C

M 200

CM

300F

ootnotes

Foot Mounted & C-Face Foot Mounted 575V IP44Enclosure HP Speed- RPM Voltage Inverter Norm. Frame 575V US List Notes

Base CHP Torque/Spd Stock Amps PriceTENV 2 1200 1800 575 CT 1000:1 No 184TC 2.1 $1,204 NV00212CXZCATEFC 2 1200 1800 575 CT 1000:1 No 182TC 2.6 $1,204 FC00212CXZCATENV 3 1800 2700 575 CT 1000:1 No 182TC 3.0 $966 NV00318CXZCATEFC 3 1800 2700 575 CT 1000:1 No 182TC 3.7 $966 FC00318CXZCATEFC 3 1200 1800 575 CT 1000:1 No 213TC 3.8 $1,515 FC00312CXZCATENV 3 1200 1800 575 CT 1000:1 No 215T 3.1 $1,515 NV00312CXZHATENV 5 1800 2700 575 CT 1000:1 No L184TC 5.1 $1,129 NV00518CXZCATEFC 5 1800 2700 575 CT 1000:1 No L184TC 5.9 $1,129 FC00518CXZCATEFC 5 1200 1800 575 CT 1000:1 No L215TC 6.1 $1,756 FC00512CXZCATENV 5 1200 1800 575 CT 1000:1 No L215T 5.4 $1,756 NV00512CXZHATENV 7.5 1800 2700 575 CT 1000:1 No L215TC 7.4 $1,412 NV7F518CXZCATEFC 7.5 1800 2700 575 CT 1000:1 No 213TC 8.6 $1,412 FC7F518CXZCATEFC 7.5 1200 1800 575 CT 1000:1 No 254T 7.6 $2,215 FC7F512CXZHATENV 10 1800 2700 575 CT 1000:1 No 254TC 10 $1,699 NV01018CXZCATEFC 10 1800 2700 575 CT 1000:1 No L215TC 10 $1,638 FC01018CXZCATEFC 10 1200 1800 575 CT 1000:1 No 256T 10 $2,509 FC01012CXZHATENV 15 1800 2700 575 CT 1000:1 No 256TC 15 $2,182 NV01518CXZCATEFC 15 1800 2700 575 CT 1000:1 No 254TC 17 $2,182 FC01518CXZCATEFC 15 1200 1800 575 CT 1000:1 No 284T 15 $2,963 FC01512CXZHATENV 20 1800 2700 575 CT 1000:1 No 284T 19 $2,452 NV02018CXZHATEFC 20 1800 2700 575 CT 1000:1 No 256TC 20 $2,154 FC02018CXZCATEFC 20 1200 1800 575 CT 1000:1 No 286T 20 $3,370 FC02012CXZHATENV 25 1800 2700 575 CT 1000:1 No 324T 24 $3,265 NV02518CXZHATEFC 25 1800 2700 575 CT 1000:1 No 284TC 25 $2,724 FC02518CXZCATEFC 25 1200 1800 575 CT 1000:1 No 324T 25 $4,423 FC02512CXZHATENV 30 1800 2700 575 CT 1000:1 No 326T 29 $5,066 NV03018CXZHATEFC 30 1800 2700 575 CT 1000:1 No 286T 30 $2,872 FC03018CXZHATEFC 30 1200 1800 575 CT 1000:1 No 326T 30 $5,413 FC03012CXZHATENV 40 1800 2700 575 CT 1000:1 No 364T 38 $6,189 NV04018CXZHATEFC 40 1800 2700 575 CT 1000:1 No 324T 40 $4,031 FC04018CXZHATEFC 40 1200 1800 575 CT 1000:1 No 364T 40 $6,521 FC04012CXZHATENV 50 1800 2700 575 CT 1000:1 No 404T 46 $7,683 NV05018CXZHATEFC 50 1800 2700 575 CT 1000:1 No 326T 50 $4,927 FC05018CXZHATEFC 50 1200 1800 575 CT 1000:1 No 365T 49 $8,078 FC05012CXZHATEFC 60 1800 2700 575 CT 1000:1 No 364T 57 $6,104 FC06018CXZHATEFC 60 1200 1800 575 CT 1000:1 No 404T 57 $9,640 FC06012CXZHATEFC 75 1800 2700 575 CT 1000:1 No 365T 72 $7,645 FC07518CXZHATEFC 75 1200 1800 575 CT 1000:1 No 405T 68 $10,555 FC07512CXZHATEFC 100 1800 2700 575 CT 1000:1 No 405T 92 $9,882 FC10018CXZHATEFC 100 1200 1800 575 CT 1000:1 No 444T 95 $13,634 FC10012CXZHATEFC 125 1800 2700 575 CT 1000:1 No 444T 121 $12,265 FC12518CXZHATEFC 125 1200 1800 575 CT 1000:1 No 445T 121 $15,310 FC12512CXZHATEFC 150 1800 2700 575 CT 1000:1 No 445T 142 $14,638 FC15018CXZHATEFC 150 1200 1800 575 CT 1000:1 No 447T 142 $18,887 FC15012CXZHATEFC 200 1800 2700 575 CT 1000:1 No 447T 181 $17,344 FC20018CXZHATEFC 200 1200 1800 575 CT 1000:1 No 449T 184 $23,475 FC20012CXZHATEFC 250 1800 2700 575 CT 1000:1 No 449T 223 $21,441 FC25018CXZHATEFC 250 1200 1800 575 CT 1000:1 No 449T 232 $27,358 FC25012CXZHA 121TEFC 250 1200 1800 575 CT 1000:1 No L449T 232 $29,400 FC25012CXZHATEFC 300 1800 2700 575 CT 1000:1 No 449T 270 $24,514 FC30018CXZHATEFC 300 1200 1800 575 CT 1000:1 No L449T 283 $36,761 FC30012CXZHATEFC 350 1800 2700 575 CT 1000:1 No L449T 318 $29,411 FC35018CXZHATEFC 400 1800 2700 575 CT 1000:1 No L449T 356 $39,302 FC40018CXZHATEFC 450 1800 2700 575 CT 1000:1 No L449T 401 $47,280 FC45018CXZHATEFC 500 1800 2700 575 CT 4:1 No L449T 441 $48,673 FC50018CXKHA 122



79

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es





CONDUIT BOX: Mounting of stock box kits (price includes box):314 Convert to cast iron or oversize 180-320 ALL

360-445 ALL315 Auxiliary box attached to main conduit box ALL ALL316 Drill drain hole ALL ALL

CONNECTIONS:319 Final connect dual to single voltage. 180-320 ALL

360-449 ALLDRAINS: Install automatic breather drains, one in each motor end bracket:

323 Stainless steel T-drain ALL ALLNote: Mounting position must be specified e.g. F-1, W-1, etc.DRIPCOVERS:

326 Mounting of stock canopy kits (includes drip cover kits) 180-210 TEFCThis modification does not provide vertical lifting 250-280 TEFCThis modification is not available if encoder has been added. 320-360 TEFCEND BRACKET: Modify a foot mounted motor to include a C-Face end bracket.Note: Add seal modification seperately, if required.

330 Changing from std. end to C-face with feet (Non-NEMA BA) 180-250 ALL331 Changing from std. end to C-face with feet (NEMA BA) 280-360 ALL

FEEDBACK DEVICE:Mounting of stock encoder kits. Price includes all material and labor to mountencoder on Opposite Drive End of motor.

337 BEI HS35, 5-15 vdc supply, Single output, 1024 ppr w/ marker pulse 180-250 TENV338 BEI HS35, 5-15 vdc supply, Single output, 1024 ppr w/ marker pulse 180-440 TEFC339 BEI HS35, 5-24 vdc supply, Single output, 2048 ppr w/ marker pulse 180-440 TEFC340 BEI HS35, 5-24 vdc supply, single output, 1024 ppr w/ marker pulse 180-250 TENV341 BEI HS35, 5-24 vdc supply, single output, 1024 ppr w/ marker pulse 180-440 TEFC342 Lakeshore HS35M, 5-26 vdc supply, single output, 1024 ppr w/ marker pulse 180-250 TENV343 Lakeshore HS35M, 5-26 vdc supply, single output, 1024 ppr w/ marker pulse 180-440 TEFC344 Avtron M3, 5-18 vdc supply, single output, 1024 ppr w/ marker pulse 180-250 TENV345 Avtron M3, 5-18 vdc supply, single output, 1024 ppr w/ marker pulse 180-440 TEFC

GREASE FITTINGS: Install a grease fitting on each bearing.358 Alemite 1610 or button head zerk fitting 250-449 ALL

GROUNDING: (All motors have provision for grounding)361 Clamp type in conduit box ALL ALL

INSULATION: Tropical protection364 Addition of anti-fungus treatment to windings. 180-286 ALL

324-445 ALLLEAD TERMINALS: Additon of lead terminals to wires in conduit box.

368 Compression type (Burndy, etc.) lead lugs ALL ALL



Changes to an Order

$214$429$704$214

$214$286

$704

$286$357$429

$561

$1123

$847

$1123

$1378

$1123

$1378

$1123

$2552

$1123

$2552

$214

$214

$429

$357

$561


80

General

Information

CM

100C

M 200

CM

300F

ootnotes

Modifications Available to CM202 MotorsMILL AND CHEM DUTY: Add features for additional reliability in harsh Mill and Chem applications.

371 Convert to cast iron fan shroud and conduit box. 180-280 TEFC320-400 TEFC440-449 TEFC

MOUNTING: Move conduit box to allow different mounting configurations.372 F-1 to F-2 180-280 ALL

Note: Not available on L180-L210 frames 320-449 ALL373 F-1 to W6 180-280 ALL




Note: Not available on L180-L210 frames 320-449 ALLSEALS: Addition of shaft seal.

377 V-ring rubber slinger on drive end ALL ALLSPACE HEATERS:

380 Addition of 120V single phase, 60 Hz space heater, aux CB not included 180-280 ALL320-400 ALL

440-L449 ALLTERMINAL BLOCK: Mounting of terminal block in conduit box.Note: Limited to single voltage motors with three leads.

385 IEC style terminal block (price by frame size) 180-210 TEFC386 NEMA terminal strip (price by frame size) 250-280 TEFC

320-360 TEFC400-440 TEFC

$561

$286

$847$1419

$429

$429

$286

$286

$429

$429

$286

$286

$286

$429

$500

$286

$1133

$561

$561

$847

$704


81

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Accessory Kits for CM202 Motors

EncodersFrame Enclosure Supply Output/PPR AB Model AB List AB Cost Mounting Kit AB List

Type Voltage Number Price Model Price180T-250T TENV BEI HS35 5 to 15 vdc CMKIT-K99G32 $1,021 $330 CMKIT-K18G22 $102180T-440T TEFC BEI HS35 5 to 15 vdc CMKIT-K99G32 $1,021 $330 CMKIT-K21G23 $102180T-440T TEFC BEI HS35 5 to 24 vdc CMKIT-K99G36 $1,021 $330 CMKIT-K21G23 $102180T-250T TENV BEI HS35 5 to 24 vdc CMKIT-K99G34 $1,021 $330 CMKIT-K18G22 $102180T-440T TEFC BEI HS35 5 to 24 vdc CMKIT-K99G34 $1,021 $330 CMKIT-K21G23 $102180T-250T TENV MagCoder HS35M 5 to 26 vdc CMKIT-K99G35 $1,276 $413 CMKIT-K21G25 $102180T-440T TEFC MagCoder MS35M 5 to 26 vdc CMKIT-K99G35 $1,276 $413 CMKIT-K21G23 $102180T-250T TENV Avtron M3 5 to 18 vdc CMKIT-K99G33 $2,348 $759 CMKIT-K18G23 $204210T-440T TEFC Avtron M3 5 to 18 vdc CMKIT-K99G33 $2,348 $759 CMKIT-K21G24 $204


NOTES: For mounting of the above encoders and kits by Reliance Electric, see the Modification Center price pages of this section. See the Variable speed Catalog or the Configurator for a complete list of encoders available on production Inverter Duty AC motor orders.

Avtron M3 - This is an optical hollow shaft encoder with a single output, 1024 ppr, that has two channel quadrature outputs (A and B) with complementary outputs and a marker pulse (Z). The encoder requires 5-18 vdc input and is rated for 85 degrees C ambient, 5000 rpm maximum and has a totally sealed, cast aluminum housing with polyurethane enamel paint. See Avtron's web site for additional information, www.avtron.com.

MagCoder HS35M - The MagCoder HS35M is a hollow shaft encoder with a single output, 1024 ppr, that has two channel quadrature outputs (A and B) with complementary outputs and a marker pulse (Z). The encoder requires 5-26 vdc input and is rated for 80 degrees C ambient, 3600 rpm maximum and has a IP65 enclosure rating. The MagCoder uses maneto resistive technology which makes it immune to common contaminants. The MagCoder HS35M was previously identified as a LakeShore product, but is now manufactured by Danaher Controls which also makes DynaPar encoders. For more information on LakeShore or DynaPar encoders, see web site www.dancom.com.

BEI HS35 - This is an optical hollow shaft encoder with a single output, 1024 ppr, that has two channel quadrature outputs (A andB0 with complementary outputs and a market pulse (Z). Two versions of the encoder are stocked, 5 to 15 vdc input and a 5 to 26 vdc input, both are rated for 70 degrees C ambient, 6000 rpm maximum and have a IP65 enclosure rating. This encoder comes with a protective cover as shown in the above picture. See BEI's web site for additional information, www.beiied.com.


82

General

Information

CM

100C

M 200

CM

300F

ootnotes


Architecture ClassIndustrial Environment SeriesCM203 Family - Vector Duty Laminated Steel Frame AC Motors

GENERAL INFORMATION

GENERAL FEATURES

UNIQUE SQUARE LAMINATED STEEL FRAME

CM203 Family motors are designed specifically for optimum inverter duty performance. From three generations of successful experience with laminated frame DC motors, CM203 Family motors have been designed as square, laminated steel frame (L210 - L440 NEMA & DL132-DL280 IEC) to achieve maximum performance on inverter power.

CM203 Family customer benefits:• Most cost effective solutions in the industry• Square frame designs allow larger horsepower ratings in

smaller frame sizes than NEMA cast iron motors without compromise in performance or life

• Stock availability from 2 - 1000 HP• Replace larger frame NEMA AC and DC motors easily• 1000:1 constant torque in vector mode is standard on

DPFV, TENV, TEBC and TEFC as shown in catalog. • Feet located on cast iron brackets provide more rigid,

vibration-resistant structure.• Rugged laminated steel frames• Wide constant horsepower range - 4:1 to 12:1 available • High peak torque- 200% standard on enclosed motors;

300% to 400% available upon request• Low inertia for fast acceleration• Mount multiple accessories easily - encoders, brakes• Encoder provisions: machined opposite drive end bracket

and tapped shaft for addition of stub shaft are standard on DPFV, TENV and TEBC; a tapped shaft only is standard for TEFC for ease of mounting HS35 hollow shaft encoders.

TEFC 1000:1 Constant Torque RL2173 Frame

Typical Applications

CM203 Family motors have been successfully applied on a wide variety of applications. Because of the versatility to meet both wide constant torque and constant HP needs, optimum power matched solutions are available for the following:

Constant Torque: Extruders, injection molding, conveyors, paper machines, crane and hoist. Includes web processing on printing press, metal coating, film and paper coating.

Cut-to -length applications on shears used in metals and paper corrugators utilize the low inertia and mechanical ruggedness of laminated frame CM203 Family.

Constant Horsepower: Winders, unwinders, recoilers, tension reels, and machine tool spindle are examples where high peak torque to inertia for fast acceleration, and constant HP ranges of 4:1 up to 16:1 have been supplied. The ability to design very low base speeds and high response are standard with CM203 Family.

High shock and Vibration: Stamping presses for automotive and metal stamping take advantage of compact designs with feet on the brackets directly under the bearings. Includes high horsepower top drives for off shore oil rigs with the added demands of high humidity, salt spray and extreme ambient conditions.

Test stands: Again, the fast response and compact mechanical features of CM203 Family make it the choice solution for test stand applications. Depending on frame size, maximum speeds of 4000-9000 RPM are available.

Variable Torque Loads: Because of the economic advantages and compactness of CM203 Family motors, many customers have selected DPFV CM203 Family for many variable torque applications, particularly for high horsepower requirements.

CM203 Family - Vector Duty Laminated Steel Frame AC Motors

83

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


BASIS OF RATINGS

The CM203 Family motors in this catalog are designed specifically for use on IGBT voltage source controllers (PWM and six step VVI). Motor characteristics are optimized to reduce peak currents from the controller as well as to minimize motor losses. When the AC controller is properly adjusted, CM203 Family motor performance will be in accordance with published rating data. The ratings in this catalog are based on a minimum PWM frequency of 4 khz for HP through 500, 2 khz for 600 HP and higher, and a minimum ratio of PWM frequency: fundamental frequency of 20:1.

Totally Enclosed Blower Cooled With Mounted Encoder

VOLTAGE SPIKE CAPABILITY

CORONA-FREE DESIGNS

(dv/dt and peak voltages)

CM203 Family insulation systems have been tested exten-sively to insure successful operation on inverter waveshapes, including fast switching IGBTs. All motors are designed to withstand high peak voltages caused by the combination of long lead lengths and steep voltage wavefronts, with no corona formation, for AC input voltages up to 575 volts RMS. Consult the control manufacturer for specific lead length recommendations.

All CM203 Family motors have been designed to surpass the requirements of NEMA MG-1 2003, Part 31, Section 4 for definite purpose, inverter fed, polyphase motors for voltage spikes. All CM203 Family motors for base voltage rating of 460 volts and below have been qualified by test to meet a minimum of 1600 volts peak, and a dV/dt in excess of 10,000 volts per microsecond. For voltages above 460 volts, includ-ing 575 volts, motors use an insulation system which is quali-fied by test to meet minimum peak voltages of 1850 volts and dV/dt in excess of 10,000 volts per microsecond rate of rise.

STANDARD MOTOR FEATURES

AGENCY LISTINGS AND CERTIFICATIONS –RL210 through L440 Frame

ORDINARY LOCATIONS

UL file number E54825 CSA file number LR40567

All CM203 Family motors are eligible for UL component listing and CSA Certification for Ordinary Locations for all enclosures. (Please note blower changes on certain TEBC Stock Ratings below for UL listing.)

It is necessary to request the CSA, UL or CE mark at the time of order entry – there is no extra charge for this when specified on the order.*

The CE mark can be supplied on any motor, NEMA or IEC frame, but must be requested at time of order entry for NEMA frames, both stock and production.

IMPORTANT – Motors with modifications or accessories not approved by UL or CSA may not have the agency logo stamped on the nameplate.

ALTITUDE - AMBIENT

All motors in this catalog are based on 40 degrees C ambient, altitude of 3300 feet (1000 meters) above sea level at 1.0 service factor on inverter power. All motors are suitable for low ambient down to -25C as standard. Modifications can be selected for service factor, ambient and altitude as needed from the modification section.

*NOTE: On stock motors, the CSA mark for ordinary locations on all CM203 Family motors in frames RL210 - L440 (all enclosures), and UL logo in TEBC frames L360 - L440 will become standard and phased in after November 30, 2003. Both the CSA mark and UL logo will also be standard on stock DPFV and TEFC models in frames RL210 - L440, and all TENV stock models.

The CSA mark and UL logo can be supplied on all production motors. The UL logo can be obtained on stock TEBC RL210 - L320 by requesting the 56 frame blower package at no extra charge. Motor dimensions will change with 56 frame blower.


84

General

Information

CM

100C

M 200

CM

300F

ootnotes

For additional information refer to Proposal Works.

ALTITUDE - AMBIENT

All motors in this catalog are based on 40 degrees C ambient, altitude of 3300 feet (1000 meters) above sea level at 1.0 service factor on inverter power. All motors are suitable for low ambient down to -25C as standard. Modifications can be selected for service factor, ambient and altitude as needed from the modification section.

ADJUSTABLE SPEED CAPABILITY

All CM203 Family motors in this catalog are rated Vector Duty, in that they are capable of 1000:1 constant torque below base speed. They are suitable for full load torque continuously at zero speed. CM203 Family motors may be applied to inverters that are configured for vector control with encoder (flux regulated vector), sensor less vector, or scalar (volts per hertz operation). The constant torque speed range obtained is dependent on the control’s ability to properly regulate the motor flux. For example, continuous torque at zero speed may require a vector control with encoder feedback, depending on the specific performance requirements, including overloads and transient response.

OPTIMIZED FOUR & SIX POLE DESIGNS

The ratings in this catalog are based on the use of four pole laminations in frames RL210 thru L400, and six pole in L440 frame, for adjustable frequency service. By designing the motor for rated voltage at the desired base speed, motor cur-rent and therefore controller size can be minimized. The base speed is obtained by adjusting the controller frequency as required. For example, with four poles, a base speed of 1750 RPM at 460 volts would require a 60 Hz nominal controller output frequency at 460 volts. A base speed of 850 RPM would require a 30 Hz frequency setting at 460 volts output. Using this approach, motors of the same horsepower with dif-ferent base speeds will have the same nominal full load current even though frame sizes will change. Motor designs are optimized for the exact base speed and not derated or overframed.

NOTE: CM203 Family motors are optimized for inverter power supplies. Contact Rockwell Automation if by-pass mode (across-the-line) is required.

BALANCE

Standard - All CM203 Family motors meet the dynamic balance limits of NEMA MG1 Part 7 for peak value of the unfiltered velocity in inches per second as shown below:

Standard Balance Limits

See Modification section for higher grade balance (Ultra Standard and Precision) and NEMA Standard in Table 1 in Modification Section.

BEARING - INSULATED

All CM203 Family L440 frames include insulated opposite drive end bearing as standard.

BEARINGS - LUBRICATION

Standard - All CM203 Family motors use deep-grooved anti-friction ball bearings. Oversized ball bearings are standard on frames RL210 through RL250 for both coupled and belted duty. Roller bearings are used for belted duty on frames UL280 through UL440. These bearings and their internal clearances have been especially selected based on load carrying ability, thermal stresses and speed range consistent with ample bearing life. Double shielded bearings with oversize grease reservoirs that provide lifetime lubrication with no maintenance are standard on RL210-RL250 frames; bearings in frames RL210 & RL250 are not regreasable. Exclusive PLS lubrication incorporating open bearings with inner caps is standard on L280-L440 frames.

Motors designed for higher than standard speeds may use special bearing construction other than stated above.

Speed Range

EnclosureBelow Base Speed Above Base SpeedConstant Torque (1) Constant Horsepower

TEBC 1000:1 2:1 (2)

TENV 1000:1 2:1 (2)

TEFC 1000:1 2:1 (2)

DPFV 1000:1 AS PUBLISHED(1) suitable for Full Torque down to zero speed continuously on Vector controllers on which motor flux is regulated(2) See price section and Application Data for speed limitations

RPM Industrial RL210 - L440Velocity (inches / sec) Peak

0 - 1200 Per NEMA Standard1201 - 1800 .151801 - 3600 .153601 - 5000 .25001 - 8000 .2


85

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


CONDUIT BOX (TERMINAL HOUSING)

Standard construction for frames RL210 through L360 provides a gasketed, stamped steel box and cover. Boxes can be rotated in 90 degree increments, and located in any quadrant as long as accessories are not in the same quadrant.

Standard construction for frames L400 and L440 are heavy gauge mill type conduit boxes which can be mounted on either side or the top of the motor as long as not in the same quadrant as the blower. See the Modification Section for location and construction options.

For Severe Duty, Outdoor, or Paper Mill Duty, cast iron boxes are standard in frames RL210 - L360. A large mill box is standard on L400 designs and all L440 frames. Otherconduit box locations available on stock RL210-L440 and production. See modification section.

CONNECTIONS

Motor power leads and thermostat leads are terminated in the conduit box and have sufficient length (approximately 6 inches) for connecting to the power leads.

DIRECTION OF ROTATION

All CM203 Family motors are designed for bi-directional rotation. All motors are phase sequenced so that when voltages in an A-B-C phase sequence are applied to leads U/T1, V/T2, W/T3 clockwise shaft rotation facing the opposite drive end will occur.

ENCLOSURES

The basic price pages contain pricing for totally enclosed and drip-proof guarded force-ventilated motors. The IEC enclosure terminology is shown for reference only.

Drip proof Guarded Force Ventilated (IEC IP23/IC06) - ratings through 1000 HP (725kw) at 1750 RPM continuous duty (S1) are available.

Totally Enclosed Non-Ventilated (IEC IP44/IC410) - ratings available through 100 HP (75kw) continuous duty (S1), and 400 HP (300kw) 60 minute duty (S2 - 60 minutes)

Totally Enclosed Fan Cooled (IEC IC411) - ratings available through 250 HP (186kw) at 1750 RPM

Totally Enclosed Blower Cooled (IEC 416)- ratings available through 500 HP at 1750 RPM; IEC IC416 available up to 300kw at 1450 RPM.

The selection of the proper enclosure is vital to the successful safe operation of AC motors. The wrong enclosure can pose hazards to operating personnel and endanger other equip-ment. In addition, machine performance and life can be mate-rially reduced by using an enclosure inappropriate for the application. The customer must recognize the specific envi-ronmental conditions and specify the correct enclosure. Rockwell Automation can provide application assistance but must depend on the customer to provide accurate information on the operating conditions.

The information in this section and the Modification Section should be studied thoroughly before specifying an enclosure.

The basic CM203 Family motor may be Drip-proof Guarded Force Ventilated, Drip-proof Guarded Separately Ventilated or totally enclosed. The minimum enclosure for CM203 Family motors is Drip-proof Guarded (Force Ventilated) as defined by NEMA MG1-1.25.5 to prevent accidental exposure to live metal or rotating parts. The drip-proof construction permits successful operation when drops of liquid or solid particles strike or enter the enclosure at any angle from 0 to 15 degrees downward from the vertical. Certain applications may require the Splashproof Guarded (Force Ventilated) machine to permit successful operation when drops of liquid or solid particles strike or enter the enclosure at any angle not greater than 100 degrees downward from the vertical.

Both Drip-proof Guarded Force Ventilated and Splashproof Guarded Force Ventilated machines have a blower driven by a constant speed AC motor mounted on the end bracket to provide cooling independent of AC motor speed. A filter may be added to the blower when filterable contaminants are present in amounts not sufficient to rapidly clog the filter. A fil-ter is not recommended in extremely dusty, dirty locations.

Drip-Proof Guarded Force Ventilated (DPFV) Motor cooling is provided by motor-mounted blower driven by an integrally mounted three-phase blower motor.

CAUTION: The blower cooling system is designed for opti-mum cooling air flow. Blowers must not have any auxiliary duct work connected to the inlet shroud since reduction in air flow and motor overheating will occur.

Drip-Proof Guarded Separately Ventilated (DPSV) For applications where cooling air is ducted to the motor from an external source provided by the customer.

For dusty, dirty environments, a totally enclosed machine is required to prevent the free exchange of air between the inside and outside of the enclosure but not sufficiently enclosed to be termed air-tight.

Standard Conduit Box Location For All Frames, Including Stock Models

Frame Enclosure Location Terminal Blocks

RL210 - L400TENV / TEBC Top (F-3) Option

DPG-FV F-1 Option

L440TEAO-P/B F-1 Option

DPG-FV F-1 Option


86

General

Information

CM

100C

M 200

CM

300F

ootnotes


Totally Enclosed Air Over-Blower Cooled (TEBC) CM203Family in-line blower cooled motors incorporate unique inte-gral air ducts in the stator frame, external to the windings, to provide maximum cooling effectiveness. The integrally mounted, independently powered three-phase blowers result in low noise levels over wide speed ranges. TEAO-Piggyback blower is available as an option.

Totally Enclosed Non-Ventilated (TENV) Does not require any external air flow for cooling.

Totally Enclosed Fan Cooled (TEFC) Exterior surface cooled by external fan mounted on motor shaft, therefore making motor cooling dependent on motor speed.

Severe Duty Features Provides protection against corro-sive, moist and dirt laden environments as encountered in paper, chemical and similar industries. Applicable to totally enclosed motors built in frames RL210 - L440 only.

Outdoor Duty/Washdown Duty Suitable for operation out-doors subject to direct weather conditions, or for frequent washdown by high pressure water or steam. Available in all frame sizes RL210 - L440 on production basis.

Paper Mill Duty Features Designed for operation at the wet end of a paper mill and in other harsh industrial environ-ments.

Totally Enclosed Pipe-Ventilated (TEPV) or Totally Enclosed Separately-Ventilated (TESV) Motor is cooled by customer supplied air which is piped into the machine and ducted out of the machine by customer supplied ducts.

FINISH-PAINT

Standard finish is Rockwell Automation blue-green (Munsell Color System 8.5BG3.57/2.0) high-grade modified epoxy, air dry enamel with non-toxic rust inhibitors.

GROUNDING

Motors powered from adjustable frequency controllers will have voltages induced on inactive components, such as the motor frame, as a result of capacitive coupling of the switched voltage wavefronts from the controllers. PROPER GROUND-ING OF THE MOTOR FRAME IS ESSENTIAL. All CM203 Family motors have a ground lead provided in the motor conduit box as standard for grounding.

INSULATION SYSTEM

The standard insulation system for CM203 Family is ther-mally rated for NEMA Class H of 180

° C. All components of the system have been carefully selected to be fully compati-ble with any IGBT voltage source type controller, whether it is PWM or VVI. Premium VPI insulation is standard on all CM203 Family L440 frames.

MOUNTING

All CM203 Family frames are suitable for floor, wall or ceiling mount and with shaft at any angle from horizontal to vertical.

OVERLOADS

Momentary Overloads - all CM203 Family motors have been designed for an overload capability of 150% (for DPFV) and 200% (for TEBC, TENV, and TEFC) of the base speed full load torque for 1 minute at all speeds within the constant torque speed range.

Typical Motor Construction With Totally Enclosed In-line Blower And Pulse Tachometer


87

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TACHOMETER MOUNTINGAll CM203 Family motors have as a standard feature a machined opposite drive end bracket and tapped shaft provi-sion for stub shaft for mounting an integral encoder. Mounting kits are available for selected encoders. The most cost effec-tive encoder selection is a hollow shaft design and since it mounts on the stub shaft, no coupling or adapter is required. A tether arm mounts to the motor bracket.

For TEFC motors in RL210 - L400 frames, a fan cover with machined fit for accessory mounting is available as a modifi-cation, if brakes and/or coupled/bearingless encoders are required.

TEFC With Hollow Shaft HS35 Encoder

DPFV 1000HP 1750 RPM L4461 Frame

TEST - STANDARD

Each motor is given a full load test on a PWM power supply, and a routine test in accordance with IEEE 112 as modified by Rockwell Automation for inverter power. This provides customers with assurance that all motors meet design specifications. Routine test consists of:

Stator winding resistanceHi potential testNo load and full load ampsNo load and full load speed

See Modification section for price to supply certified routine test report price and other test options.

THERMAL PROTECTIONAll CM203 Family motors include three normally closed thermostats (1 per phase) connected in series, as standard. Leads are brought into the main conduit box as standard.


88

General

Information

CM

100C

M 200

CM

300F

ootnotes


CM203 Family MotorsDescription

Designed for optimum variable speed performance on AC controllers. The square laminated frame design achieves maximum adjustable speed performance. Ideal for use in demanding applications such as paper machines, machine tools, printing presses, extruders, cut-to-length, crane and hoist. All are suitable for full torque at zero speed continuously.

(1) See Pricing and Application sections for speed limitations.

TEFC EnclosureDrip-Proof

Guarded Force Ventilated (DPGFV)

Totally Enclosed Blower Cooled and

Totally Enclosed Non-Ventilated

• 1000:1 Constant Torque• 5 - 200 HP• TEFC Enclosure• 200% overload -

1 minute base speed and below• Top mounted conduit box standard

(F-1, F-2 Option)• Class H insulation• Compact• Low inertia• Fast Response• Optimized 4 pole design• RL210 - L400 frames• PLS lubrication in L280 - L400

frames• Cast iron brackets• Meets IP44

• 1000:1 Constant Torque• 15 - 1000 HP• 150% overload - 1 minute base

speed and below• F1 conduit box standard in

L210-L440• Class H insulation• Most compact• Lowest inertia• Fast response• Optimized 4 pole design (6 pole

L440)• RL210 - L440 Frame• PLS Lubrication in L280-L440 frames• Cast iron brackets• Meets IP23

• 1000:1 Constant Torque• 3 - 500 HP• 200% overload - 1 minute base

speed and below• 2 : 1 constant HP (1)• Top mounted conduit box standard

RL210-L400 frames. F-1 on L440 frame

• Class H insulation• Compact• Low inertia• Fast response• Optimized 4 pole design (6 pole

L440)• RL210 - L440 Frame• PLS Lubrication in L280-L440 frame• Cast iron brackets• Meets IP44


89

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Architecture Class, Industrial Environment SeriesCM203 - Vector Duty Laminated Steel Frame AC Motors

DPG-FV IP23Foot Mounted & C-Face Foot Mounted 460V Totally Enclosed IP44Enclosure HP Speed- RPM Voltage Inverter Norm. Frame FLA (59) US List Catalog String Notes

Base CHP Torque/Spd Stock Price CM203-TENV 2 1150 2300 460 CT 1000:1 No RL2153 3 $2,526 NV00211BXZHATENV 2 850 1700 460 CT 1000:1 No RL2153 3 $2,589 NV00208BXZHATENV 3 1150 2300 460 CT 1000:1 No RL2153 5 $2,643 NV00311BXZHATENV 3 850 1700 460 CT 1000:1 No RL2153 5 $2,670 NV00308BXZHATENV 5 3550 4000 460 CT 1000:1 No RL2153 6.8 $2,551 NV00535BXZHATENV 5 1750 3500 230/460 CT 1000:1 Yes RL2153C 14/7 $2,643 NV00517AXZCA 93TENV 5 1150 2300 460 CT 1000:1 No RL2158 5 $2,811 NV00511BXZHATENV 5 850 1700 460 CT 1000:1 No RL2162 8 $3,109 NV00508BXZHATEBC 5 850 1700 460 CT 1000:1 No RL2153 8 $2,906 BC00508BXZHATENV 7.5 3550 4000 460 CT 1000:1 No RL2153 11 $2,698 NV7F535BXZHATENV 7.5 2500 5000 460 CT 1000:1 No RL2153 0 $3,833 NV7F525BXZHATENV 7.5 1750 3500 230/460 CT 1000:1 Yes RL2158C 22/11 $2,898 NV7F517AXZCA 94TENV 7.5 1150 2300 230/460 CT 1000:1 No RL2162 22/11 $3,092 NV7F511AXZHATEBC 7.5 1150 2300 460 CT 1000:1 No RL2153 11 $3,228 BC7F511BXZHATEFC 7.5 850 1700 460 CT 1000:1 No RL2158 11 $3,136 FC7F508BXZHATEBC 7.5 850 1700 460 CT 1000:1 No RL2153 11 $3,293 BC7F508BXZHATENV 7.5 850 1700 460 CT 1000:1 No RL2173 12 $3,472 NV7F508BXZHATENV 10 3550 4000 230/460 CT 1000:1 No RL2158 28/14 $2,903 NV01035AXZHATENV 10 2500 5000 460 CT 1000:1 No RL2158 14 $4,090 NV01025BXZHATENV 10 1750 3500 230/460 CT 1000:1 Yes RL2162C 28/14 $3,020 NV01017AXZCA 94TEFC 10 1150 2300 460 CT 1000:1 No RL2162 14 $3,353 FC01011BXZHATEBC 10 1150 2300 460 CT 1000:1 No RL2158 14 $3,440 BC01011BXZHATENV 10 1150 2300 460 CT 1000:1 No RL2173 14 $3,380 NV01011BXZHA

DPG-FV 10 850 1050 460 CT 1000:1 No RL2153 14 $3,055 FV01008BXZHATEFC 10 850 1700 460 CT 1000:1 No RL2162 14 $3,185 FC01008BXZHATEBC 10 850 1700 460 CT 1000:1 No RL2158 14 $3,710 BC01008BXZHATENV 10 850 1700 460 CT 1000:1 No RL2578 14 $4,041 NV01008BXZHA

DPG-FV 15 3550 4000 460 CT 1000:1 No RL2153 21 $3,098 FV01535BXZHATEBC 15 3550 4000 460 CT 1000:1 No RL2153 21 $3,261 BC01535BXZHATENV 15 3550 4000 230/460 CT 1000:1 No RL2158 42/21 $3,309 NV01535AXZHA

DPG-FV 15 2500 3600 460 CT 1000:1 No RL2153 21 $3,180 FV01525BXZHATEBC 15 2500 5000 460 CT 1000:1 No RL2153 21 $4,537 BC01525BXZHATENV 15 2500 5000 460 CT 1000:1 No RL2162 21 $4,596 NV01525BXZHA

DPG-FV 15 1750 3500 460 CT 1000:1 No RL2153 21 $2,903 FV01517BXZHATEFC 15 1750 3500 460 CT 1000:1 Yes RL2158C 21 $3,109 FC01517BXZCA 95TEBC 15 1750 3500 460 CT 1000:1 No RL2153 21 $3,120 BC01517BXZHATENV 15 1750 3500 460 CT 1000:1 No RL2173 21 $3,228 NV01517BXZHA


DPG-FV 15 850 1050 460 CT 1000:1 No RL2158 21 $3,385 FV01508BXZHATEFC 15 850 1700 460 CT 1000:1 No RL2578 21 $3,564 FC01508BXZHATEBC 15 850 1700 460 CT 1000:1 No RL2162 21 $4,073 BC01508BXZHATENV 15 850 1700 460 CT 1000:1 No L2882 21 $8,645 NV01508BXZHA



DPG-FV 20 1750 2890 460 CT 1000:1 No RL2153C 27 $3,194 FV02017BXZCA 95TEFC 20 1750 3500 460 CT 1000:1 Yes RL2162C 27 $3,239 FC02017BXZCA 95TEBC 20 1750 3500 460 CT 1000:1 No RL2158C 27 $3,255 BC02017BXZCA 95TENV 20 1750 3500 460 CT 1000:1 No RL2578 27 $3,618 NV02017BXZHA

DPG-FV 20 1150 1300 460 CT 1000:1 No RL2158C 27 $3,406 FV02011BXZCA 95TEFC 20 1150 2300 460 CT 1000:1 No RL2578 27 $3,662 FC02011BXZHATEBC 20 1150 2300 460 CT 1000:1 No RL2168 27 $3,781 BC02011BXZHATENV 20 1150 2300 460 CT 1000:1 No L2890 27 $8,761 NV02011BXZHA

DPG-FV 20 850 1050 460 CT 1000:1 No RL2162 27 $3,774 FV02008BXZHATEFC 20 850 1700 460 CT 1000:1 No RL2586 27 $4,539 FC02008BXZHA


90

General

Information

CM

100C

M 200

CM

300F

ootnotes

Enclosure HP Speed- RPM Voltage Inverter Norm. Frame FLA (59) US List Catalog String NotesBase CHP Torque/Spd Stock Price CM203-

TEBC 20 850 1700 460 CT 1000:1 No RL2173 27 $4,344 BC02008BXZHATENV 20 850 1700 460 CT 1000:1 No L2898 27 $9,945 NV02008BXZHA



DPG-FV 25 1750 2600 460 CT 1000:1 No RL2158C 34 $3,430 FV02517BXZCA 95TEFC 25 1750 3550 460 CT 1000:1 Yes RL2173C 34 $3,562 FC02517BXZCA 95TEBC 25 1750 3500 460 CT 1000:1 Yes RL2162C 34 $3,510 BC02517BXZCA 95TENV 25 1750 3500 460 CT 1000:1 No RL2586 34 $4,316 NV02517BXZHA


DPG-FV 25 850 1050 460 CT 1000:1 No RL2168 34 $4,344 FV02508BXZHATENV 25 850 1700 460 CT 1000:1 No L3203 34 $12,085 NV02508BXZHATEBC 25 850 1700 460 CT 1000:1 No RL2578 34 $5,319 BC02508BXZHA


DPG-FV 30 2500 3000 460 CT 1000:1 No RL2153 40 $3,743 FV03025BXZHATEFC 30 2500 3550 460 CT 1000:1 No RL2173 40 $3,727 FC03025BXZHATENV 30 2500 4000 460 CT 1000:1 No RL2586 40 $6,679 NV03025BXZHATEBC 30 2500 5000 460 CT 1000:1 No RL2162 40 $5,066 BC03025BXZHA

DPG-FV 30 1750 2700 460 CT 1000:1 Yes RL2158C 39 $3,586 FV03017BXZCA 95TEFC 30 1750 2750 460 CT 1000:1 Yes RL2578C 40 $3,748 FC03017BXZCA 95TEBC 30 1750 3500 460 CT 1000:1 Yes RL2162C 39 $3,716 BC03017BXZCA 95TENV 30 1750 3500 460 CT 1000:1 No L2898 40 $9,697 NV03017BXZHA

DPG-FV 30 1150 1350 460 CT 1000:1 Yes RL2168 38 $4,648 FV03011BXZHATEBC 30 1150 2300 460 CT 1000:1 No RL2578 40 $5,075 BC03011BXZHATENV 30 1150 2300 460 CT 1000:1 No L3203 40 $12,177 NV03011BXZHA

DPG-FV 30 850 1050 460 CT 1000:1 No RL2173 40 $4,805 FV03008BXZHATEBC 30 850 1500 460 CT 1000:1 No RL2586 40 $5,970 BC03008BXZHATENV 30 850 1700 460 CT 1000:1 No L3213 40 $14,056 NV03008BXZHA



DPG-FV 40 1750 2000 460 CT 1000:1 Yes RL2162 52 $3,846 FV04017BXZHATEFC 40 1750 2750 460 CT 1000:1 Yes RL2586 52 $4,079 FC04017BXZHATEBC 40 1750 3500 460 CT 1000:1 Yes RL2173 52 $3,878 BC04017BXZHATENV 40 1750 3500 460 CT 1000:1 No L3203 52 $12,177 NV04017BXZHA


DPG-FV 40 850 1200 460 CT 1000:1 No RL2578 53 $7,345 FV04008BXZHATEBC 40 850 1700 460 CT 1000:1 No L2890 52 $9,579 BC04008BXZHATENV 40 850 1700 460 CT 1000:1 No L4022 52 $18,525 NV04008BXZHA



DPG-FV 50 1750 2000 460 CT 1000:1 Yes RL2168 65 $4,290 FV05017BXZHATEBC 50 1750 3500 460 CT 1000:1 Yes RL2578 61 $5,005 BC05017BXZHATENV 50 1750 3500 460 CT 1000:1 No L3203 65 $12,312 NV05017BXZHA

DPG-FV 50 1150 1300 460 CT 1000:1 Yes RL2570 65 $6,208 FV05011BXZHATEBC 50 1150 2300 460 CT 1000:1 No L2882 65 $9,403 BC05011BXZHATENV 50 1150 2300 460 CT 1000:1 No L4022 65 $18,818 NV05011BXZHA

DPG-FV 50 850 1050 460 CT 1000:1 No RL2578 69 $7,757 FV05008BXZHA


91

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEBC 50 850 1700 460 CT 1000:1 No L2898 65 $10,444 BC05008BXZHATENV 50 850 1700 460 CT 1000:1 No L4034 65 $20,554 NV05008BXZHA



DPG-FV 60 1750 2000 460 CT 1000:1 Yes RL2168 74 $5,178 FV06017BXZHATEBC 60 1750 3500 460 CT 1000:1 Yes RL2586 74 $6,478 BC06017BXZHATENV 60 1750 3500 460 CT 1000:1 No L3607 77 $18,321 NV06017BXZHA





DPG-FV 75 1750 2000 460 CT 1000:1 Yes RL2570 96 $6,218 FV07517BXZHATEBC 75 1750 3500 460 CT 1000:1 Yes L2890 94 $9,284 BC07517BXZHATENV 75 1750 3500 460 CT 1000:1 No L4022 96 $20,556 NV07517BXZHA


DPG-FV 75 850 1050 460 CT 1000:1 No L2882 96 $11,527 FV07508BXZHATEBC 75 850 1700 460 CT 1000:1 No L3213 96 $14,733 BC07508BXZHA

DPG-FV 100 3550 3800 460 CT 1000:1 No RL2570 124 $8,873 FV10035BXZHATEBC 100 3550 4000 460 CT 1000:1 No L2890 124 $10,671 BC10035BXZHA


DPG-FV 100 1750 2000 460 CT 1000:1 Yes RL2578 119 $7,540 FV10017BXZHATEBC 100 1750 3500 460 CT 1000:1 Yes L2898 123 $9,978 BC10017BXZHATENV 100 1750 3500 460 CT 1000:1 No L4046 124 $25,262 NV10017BXZHA

DPG-FV 100 1150 1450 460 CT 1000:1 Yes L2882 124 $11,429 FV10011BXZHATEBC 100 1150 2300 460 CT 1000:1 No L3213 124 $13,693 BC10011BXZHA




DPG-FV 125 1750 2000 460 CT 1000:1 Yes RL2586 148 $9,994 FV12517BXZHATEBC 125 1750 3500 460 CT 1000:1 Yes L3203 150 $12,794 BC12517BXZHA





DPG-FV 150 1750 2000 460 CT 1000:1 Yes L2882 180 $11,158 FV15017BXZHATEBC 150 1750 3500 460 CT 1000:1 Yes L3213 177 $17,117 BC15017BXZHA



92

General

Information

CM

100C

M 200

CM

300F

ootnotes







DPG-FV 200 850 1050 460 CT 1000:1 No L3614 240 $23,617 FV20008BXZHATEAO-P/B 200 850 1700 460 CT 1000:1 No L4440 270 $38,675 AO20008BXZHA 92DPG-FV 250 3550 3850 460 CT 1000:1 No L2898 300 $18,525 FV25035BXZHATEBC 250 3550 4000 460 CT 1000:1 No L4034 300 $25,579 BC25035BXZHA



DPG-FV 250 1150 2000 460 CT 1000:1 Yes L3614 289 $20,475 FV25011BXZHATEBC 250 1150 2300 460 CT 1000:1 No L4429 325 $43,111 BC25011BXZHA 92

DPG-FV 250 850 1350 460 CT 1000:1 No L4034 325 $30,983 FV25008BXZHATEAO-P/B 250 850 1700 460 CT 1000:1 No L4461 325 $53,439 AO25008BXZHA 92DPG-FV 300 3550 3850 460 CT 1000:1 No L3203 360 $21,536 FV30035BXZHADPG-FV 300 2500 3000 460 CT 1000:1 No L3213 360 $20,512 FV30025BXZHATEBC 300 2500 3500 460 CT 1000:1 No L4046 360 $30,203 BC30025BXZHA


DPG-FV 300 1150 2000 460 CT 1000:1 Yes L4034 360 $26,119 FV30011BXZHATEAO-P/B 300 1150 2300 460 CT 1000:1 No L4451 390 $46,378 AO30011BXZHA 92DPG-FV 300 850 1050 460 CT 1000:1 No L4046 390 $36,032 FV30008BXZHA

TEDC-A/A 300 850 1200 460 CT 1000:1 No L4461 390 $74,533 AA30008BXZHADPG-FV 350 3550 3850 460 CT 1000:1 No L3203 415 $26,466 FV35035BXZHADPG-FV 350 2500 3000 460 CT 1000:1 No L3213 415 $26,108 FV35025BXZHADPG-FV 350 1750 2200 460 CT 1000:1 Yes L3614 401 $22,615 FV35017BXZHA

TEAO-P/B 350 1750 2700 460 CT 1000:1 No L4440 440 $35,317 AO35017BXZHA 92DPG-FV 350 1150 1700 460 CT 1000:1 No L4046 440 $28,004 FV35011BXZHA

TEAO-P/B 350 1150 2300 460 CT 1000:1 No L4461 440 $47,883 AO35011BXZHA 92DPG-FV 350 850 1000 460 CT 1000:1 No L4429 450 $46,367 FV35008BXZHA

TEDC-A/A 350 850 1400 460 CT 1000:1 No L4461 450 $74,533 AA35008BXZHADPG-FV 400 3550 3850 460 CT 1000:1 No L3213 477 $28,763 FV40035BXZHADPG-FV 400 2500 3000 460 CT 1000:1 No L3213 477 $28,383 FV40025BXZHADPG-FV 400 1750 2500 460 CT 1000:1 Yes L3614 477 $25,242 FV40017BXZHA

TEAO-P/B 400 1750 2700 460 CT 1000:1 No L4451 536 $41,118 AO40017BXZHA 92TEAO-P/B 400 1450 2300 460 CT 1000:1 No L4461 565 $51,133 AO40012BXZHA 92DPG-FV 400 1150 2000 460 CT 1000:1 No L4046 451 $38,133 FV40011BXZHA

TEDC-A/A 400 1150 1800 460 CT 1000:1 No L4461 505 $74,533 AA40011BXZHADPG-FV 400 850 1000 460 CT 1000:1 No L4440 505 $50,429 FV40008BXZHADPG-FV 450 3550 3850 460 CT 1000:1 No L3213 534 $31,200 FV45035BXZHADPG-FV 450 2500 3000 460 CT 1000:1 No L3614 534 $29,900 FV45025BXZHADPG-FV 450 1750 2500 460 CT 1000:1 No L4034 534 $27,192 FV45017BXZHA

TEAO-P/B 450 1750 2700 460 CT 1000:1 No L4461 563 $47,537 AO45017BXZHA 92DPG-FV 450 1150 1700 460 CT 1000:1 No L4429 572 $46,367 FV45011BXZHADPG-FV 450 850 1000 460 CT 1000:1 No L4451 568 $54,600 FV45008BXZHADPG-FV 500 3550 3850 460 CT 1000:1 No L3614 590 $34,125 FV50035BXZHADPG-FV 500 2500 3000 460 CT 1000:1 No L4034 590 $33,367 FV50025BXZHADPG-FV 500 1750 2400 460 CT 1000:1 No L4034 557 $31,157 FV50017BXZHADPG-FV 500 1750 2400 460 CT 1000:1 Yes L4034 557 $33,323 FV50017BXZHB 109

TEAO-P/B 500 1750 2500 460 CT 1000:1 No L4461 613 $47,883 AO50017BXZHA 92, 108DPG-FV 500 1150 1700 460 CT 1000:1 No L4440 625 $50,429 FV50011BXZHADPG-FV 500 850 1000 460 CT 1000:1 No L4461 625 $56,983 FV50008BXZHADPG-FV 600 1750 2200 460 CT 1000:1 No L4046 666 $38,458 FV60017BXZHADPG-FV 600 1750 2200 460 CT 1000:1 Yes L4046 666 $40,625 FV60017BXZHB 109

TEDC-A/A 600 1750 2700 460 CT 1000:1 No L4461 750 $76,744 AA60017BXZHADPG-FV 600 1150 1700 460 CT 1000:1 No L4451 750 $54,600 FV60011BXZHADPG-FV 700 1750 2000 460 CT 1000:1 No L4429 875 $48,533 FV70017BXZHADPG-FV 700 1750 2300 460 CT 1000:1 Yes L4429 875 $50,700 FV70017BXZHB 109


93

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEDC-A/A 700 1750 2700 460 CT 1000:1 No L4461 875 $77,133 AA70017BXZHADPG-FV 700 1200 1750 460 CT 1000:1 No L4461 875 $56,983 FV70012BXZHADPG-FV 800 1750 2300 460 CT 1000:1 No L4440 975 $52,596 FV80017BXZHA

TEDC-A/W 800 1750 2000 460 CT 1000:1 No L4461 975 $79,777 AW80017BXZHADPG-FV 800 1450 1800 460 CT 1000:1 No L4461 980 $59,150 FV80014BXZHADPG-FV 900 1750 2000 460 CT 1000:1 No L4451 1095 $56,767 FV90017BXZHA

TEDC-A/W 900 1750 2000 460 CT 1000:1 No L4461 1095 $80,275 AW90017BXZHADPG-FV 1000 1750 2000 460 CT 1000:1 Yes L4461 1202 $63,538 FV1K017BXZHA 108

TEDC-A/W 1000 1750 2000 460 CT 1000:1 No L4461 1202 $81,077 AW1K017BXZHA 108Discount Schedule 16

IP23Foot Mounted & C-Face Foot Mounted 575V IP44Enclosure HP Speed- RPM Voltage Inverter Norm. Frame FLA (59) US List Catalog String Notes

Base CHP Torque/Spd Stock Price CM203-TENV 2 1150 2300 575 CT 1000:1 No RL2153 $2,526 NV00211CXZHATENV 2 850 1700 575 CT 1000:1 No RL2153 $2,589 NV00208CXZHATENV 3 1150 2300 575 CT 1000:1 No RL2153 $2,643 NV00311CXZHATENV 3 850 1700 575 CT 1000:1 No RL2153 $2,670 NV00308CXZHATENV 5 3550 4000 575 CT 1000:1 No RL2153 $2,551 NV00535CXZHATENV 5 1750 3500 575 CT 1000:1 No RL2153C $2,643 NV00517CXZCA 93TENV 5 1150 2300 575 CT 1000:1 No RL2158 $2,811 NV00511CXZHATENV 5 850 1700 575 CT 1000:1 No RL2162 $3,109 NV00508CXZHATEBC 5 850 1700 575 CT 1000:1 No RL2153 $2,906 BC00508CXZHATENV 7.5 3550 4000 575 CT 1000:1 No RL2153 $2,698 NV7F535CXZHATENV 7.5 2500 5000 575 CT 1000:1 No RL2153 $3,833 NV7F525CXZHATENV 7.5 1750 3500 575 CT 1000:1 No RL2158C $2,898 NV7F517CXZCA 94TENV 7.5 1150 2300 575 CT 1000:1 No RL2162 $3,092 NV7F511CXZHATEBC 7.5 1150 2300 575 CT 1000:1 No RL2153 $3,228 BC7F511CXZHATEFC 7.5 850 1700 575 CT 1000:1 No RL2158 $3,136 FC7F508CXZHATEBC 7.5 850 1700 575 CT 1000:1 No RL2153 $3,293 BC7F508CXZHATENV 7.5 850 1700 575 CT 1000:1 No RL2173 $3,472 NV7F508CXZHATENV 10 3550 4000 575 CT 1000:1 No RL2158 $2,903 NV01035CXZHATENV 10 2500 5000 575 CT 1000:1 No RL2158 $4,090 NV01025CXZHATENV 10 1750 3500 575 CT 1000:1 No RL2162C $3,020 NV01017CXZCA 94TEFC 10 1150 2300 575 CT 1000:1 No RL2162 $3,353 FC01011CXZHATEBC 10 1150 2300 575 CT 1000:1 No RL2158 $3,440 BC01011CXZHATENV 10 1150 2300 575 CT 1000:1 No RL2173 $3,380 NV01011CXZHA

DPG-FV 10 850 1050 575 CT 1000:1 No RL2153 $3,055 FV01008CXZHATEFC 10 850 1700 575 CT 1000:1 No RL2162 $3,185 FC01008CXZHATEBC 10 850 1700 575 CT 1000:1 No RL2158 $3,710 BC01008CXZHATENV 10 850 1700 575 CT 1000:1 No RL2578 $4,041 NV01008CXZHA

DPG-FV 15 3550 4000 575 CT 1000:1 No RL2153 $3,098 FV01535CXZHATEBC 15 3550 4000 575 CT 1000:1 No RL2153 $3,261 BC01535CXZHATENV 15 3550 4000 575 CT 1000:1 No RL2158 $3,309 NV01535CXZHA


DPG-FV 15 1750 3500 575 CT 1000:1 No RL2153 $2,903 FV01517CXZHATEFC 15 1750 3500 575 CT 1000:1 No RL2158C $3,109 FC01517CXZCA 95TEBC 15 1750 3500 575 CT 1000:1 No RL2153 $3,120 BC01517CXZHATENV 15 1750 3500 575 CT 1000:1 No RL2173 $3,228 NV01517CXZHA


DPG-FV 15 850 1050 575 CT 1000:1 No RL2158 $3,385 FV01508CXZHATEFC 15 850 1700 575 CT 1000:1 No RL2578 $3,564 FC01508CXZHATEBC 15 850 1700 575 CT 1000:1 No RL2162 $4,073 BC01508CXZHATENV 15 850 1700 575 CT 1000:1 No L2882 $8,645 NV01508CXZHA


94

General

Information

CM

100C

M 200

CM

300F

ootnotes




DPG-FV 20 1750 2890 575 CT 1000:1 No RL2153C $3,194 FV02017CXZCA 95TEFC 20 1750 3500 575 CT 1000:1 No RL2162C $3,239 FC02017CXZCA 95TEBC 20 1750 3500 575 CT 1000:1 No RL2158C $3,255 BC02017CXZCA 95TENV 20 1750 3500 575 CT 1000:1 No RL2578 $3,618 NV02017CXZHA

DPG-FV 20 1150 1300 575 CT 1000:1 No RL2158C $3,406 FV02011CXZCA 95TEFC 20 1150 2300 575 CT 1000:1 No RL2578 $3,662 FC02011CXZHATEBC 20 1150 2300 575 CT 1000:1 No RL2168 $3,781 BC02011CXZHATENV 20 1150 2300 575 CT 1000:1 No L2890 $8,761 NV02011CXZHA




DPG-FV 25 1750 2600 575 CT 1000:1 No RL2158C $3,430 FV02517CXZCA 95TEFC 25 1750 3550 575 CT 1000:1 No RL2173C $3,562 FC02517CXZCA 95TEBC 25 1750 3500 575 CT 1000:1 No RL2162C $3,510 BC02517CXZCA 95TENV 25 1750 3500 575 CT 1000:1 No RL2586 $4,316 NV02517CXZHA


DPG-FV 25 850 1050 575 CT 1000:1 No RL2168 $4,344 FV02508CXZHATENV 25 850 1700 575 CT 1000:1 No L3203 $12,085 NV02508CXZHATEBC 25 850 1700 575 CT 1000:1 No RL2578 $5,319 BC02508CXZHA


DPG-FV 30 2500 3000 575 CT 1000:1 No RL2153 $3,743 FV03025CXZHATEFC 30 2500 3550 575 CT 1000:1 No RL2173 $3,727 FC03025CXZHATENV 30 2500 4000 575 CT 1000:1 No RL2586 $6,679 NV03025CXZHATEBC 30 2500 5000 575 CT 1000:1 No RL2162 $5,066 BC03025CXZHA

DPG-FV 30 1750 3475 575 CT 1000:1 No RL2158C $3,586 FV03017CXZCA 95TEFC 30 1750 2750 575 CT 1000:1 No RL2578C $3,748 FC03017CXZCA 95TEBC 30 1750 3500 575 CT 1000:1 No RL2162C $3,716 BC03017CXZCA 95TENV 30 1750 3500 575 CT 1000:1 No L2898 $9,697 NV03017CXZHA

DPG-FV 30 1150 1350 575 CT 1000:1 No RL2168 $4,648 FV03011CXZHATEBC 30 1150 2300 575 CT 1000:1 No RL2578 $5,075 BC03011CXZHATENV 30 1150 2300 575 CT 1000:1 No L3203 $12,177 NV03011CXZHA







95

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


DPG-FV 40 850 1200 575 CT 1000:1 No RL2578 $7,345 FV04008CXZHATEBC 40 850 1700 575 CT 1000:1 No L2890 $9,579 BC04008CXZHATENV 40 850 1700 575 CT 1000:1 No L4022 $18,525 NV04008CXZHA















DPG-FV 75 850 1050 575 CT 1000:1 No L2882 $11,527 FV07508CXZHATEBC 75 850 1700 575 CT 1000:1 No L3213 $14,733 BC07508CXZHA

DPG-FV 100 3550 3800 575 CT 1000:1 No RL2570 $8,873 FV10035CXZHATEBC 100 3550 4000 575 CT 1000:1 No L2890 $10,671 BC10035CXZHA










96

General

Information

CM

100C

M 200

CM

300F

ootnotes












DPG-FV 200 850 1050 575 CT 1000:1 No L3614 $23,617 FV20008CXZHATEAO-P/B 200 850 1700 575 CT 1000:1 No L4440 $38,675 AO20008CXZHA 92DPG-FV 250 3550 3850 575 CT 1000:1 No L2898 $18,525 FV25035CXZHATEBC 250 3550 4000 575 CT 1000:1 No L4034 $25,579 BC25035CXZHA



DPG-FV 250 1150 2000 575 CT 1000:1 No L3614 $20,475 FV25011CXZHATEAO-P/B 250 1150 2300 575 CT 1000:1 No L4429 $43,111 AO25011CXZHA 92DPG-FV 250 850 1350 575 CT 1000:1 No L4034 $30,983 FV25008CXZHATEBC 250 850 1700 575 CT 1000:1 No L4461 $53,439 BC25008CXZHA 92

DPG-FV 300 3550 3850 575 CT 1000:1 No L3203 $21,536 FV30035CXZHADPG-FV 300 2500 3000 575 CT 1000:1 No L3213 $20,512 FV30025CXZHATEBC 300 2500 3500 575 CT 1000:1 No L4046 $30,203 BC30025CXZHA


DPG-FV 300 1150 2000 575 CT 1000:1 No L4034 $26,119 FV30011CXZHATEAO-P/B 300 1150 2300 575 CT 1000:1 No L4451 $46,378 AO30011CXZHA 92DPG-FV 300 850 1050 575 CT 1000:1 No L4046 $36,032 FV30008CXZHA

TEDC-A/A 300 850 1200 575 CT 1000:1 No L4461 $74,533 AA30008CXZHADPG-FV 350 3550 3850 575 CT 1000:1 No L3203 $26,466 FV35035CXZHADPG-FV 350 2500 3000 575 CT 1000:1 No L3213 $26,108 FV35025CXZHADPG-FV 350 1750 2200 575 CT 1000:1 No L3614 $22,615 FV35017CXZHA

TEAO-P/B 350 1750 2700 575 CT 1000:1 No L4440 $35,317 AO35017CXZHA 92DPG-FV 350 1150 1700 575 CT 1000:1 No L4046 $28,004 FV35011CXZHATEBC 350 1150 2300 575 CT 1000:1 No L4461 $47,883 BC35011CXZHA 92

DPG-FV 350 850 1000 575 CT 1000:1 No L4429 $46,367 FV35008CXZHATEDC-A/A 350 850 1400 575 CT 1000:1 No L4461 $74,533 AA35008CXZHADPG-FV 400 3550 3850 575 CT 1000:1 No L3213 $28,763 FV40035CXZHADPG-FV 400 2500 3000 575 CT 1000:1 No L3213 $28,383 FV40025CXZHADPG-FV 400 1750 2500 575 CT 1000:1 No L3614 $25,242 FV40017CXZHA

TEAO-P/B 400 1750 2700 575 CT 1000:1 No L4451 $41,118 AO40017CXZHA 92TEAO-P/B 400 1450 2300 575 CT 1000:1 No L4461 $51,133 AO40012CXZHA 92DPG-FV 400 1150 2000 575 CT 1000:1 No L4046 $38,133 FV40011CXZHA

TEDC-A/A 400 1150 1800 575 CT 1000:1 No L4461 $74,533 AA40011CXZHADPG-FV 400 850 1000 575 CT 1000:1 No L4440 $50,429 FV40008CXZHADPG-FV 450 3550 3850 575 CT 1000:1 No L3213 $31,200 FV45035CXZHADPG-FV 450 2500 3000 575 CT 1000:1 No L3614 $29,900 FV45025CXZHADPG-FV 450 1750 2500 575 CT 1000:1 No L4034 $27,192 FV45017CXZHA

TEAO-P/B 450 1750 2700 575 CT 1000:1 No L4461 $47,537 AO45017CXZHA 92DPG-FV 450 1150 1700 575 CT 1000:1 No L4429 $46,367 FV45011CXZHADPG-FV 450 850 1000 575 CT 1000:1 No L4451 $54,600 FV45008CXZHADPG-FV 500 3550 3850 575 CT 1000:1 No L3614 $34,125 FV50035CXZHADPG-FV 500 2500 3000 575 CT 1000:1 No L4034 $33,367 FV50025CXZHADPG-FV 500 1750 2400 575 CT 1000:1 No L4034 $31,157 FV50017CXZHADPG-FV 500 1750 2400 575 CT 1000:1 No L4034 $33,323 FV50017CXZHB 109

TEAO-P/B 500 1750 2500 575 CT 1000:1 No L4461 $47,883 AO50017CXZHA 92, 108


97

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


DPG-FV 500 1150 1700 575 CT 1000:1 No L4440 $50,429 FV50011CXZHADPG-FV 500 850 1000 575 CT 1000:1 No L4461 $56,983 FV50008CXZHADPG-FV 600 1750 2200 575 CT 1000:1 No L4046 $38,458 FV60017CXZHADPG-FV 600 1750 2200 575 CT 1000:1 No L4046 $40,625 FV60017CXZHB 109

TEDC-A/A 600 1750 2700 575 CT 1000:1 No L4461 $76,744 AA60017CXZHADPG-FV 600 1150 1700 575 CT 1000:1 No L4451 $54,600 FV60011CXZHADPG-FV 700 1750 2000 575 CT 1000:1 No L4429 $48,533 FV70017CXZHADPG-FV 700 1750 2300 575 CT 1000:1 No L4429 $50,700 FV70017CXZHB 109

TEDC-A/A 700 1750 2700 575 CT 1000:1 No L4461 $77,133 AA70017CXZHADPG-FV 700 1200 1750 575 CT 1000:1 No L4461 $56,983 FV70012CXZHADPG-FV 800 1750 2300 575 CT 1000:1 No L4440 $52,596 FV80017CXZHA

TEDC-A/W 800 1750 2000 575 CT 1000:1 No L4461 $79,777 AW80017CXZHADPG-FV 800 1450 1800 575 CT 1000:1 No L4461 $59,150 FV80012CXZHADPG-FV 900 1750 2000 575 CT 1000:1 No L4451 $56,767 FV90017CXZHA

TEDC-A/W 900 1750 2000 575 CT 1000:1 No L4461 $80,275 AW90017CXZHADPG-FV 1000 1750 2000 575 CT 1000:1 No L4461 $63,538 FV1K017CXZHA 108

TEDC-A/W 1000 1750 2000 575 CT 1000:1 No L4461 $81,077 AW1K017CXZHA 108


98

General

Information

CM

100C

M 200

CM

300F

ootnotes

Modifications Available to CM203 MotorsGeneral InformationCancellation or Changes to an Order


Delivery Cycle


AIR PRESSURE SWITCH

Mod Est. LeadSwitch Code RL210 RL250 L280 L320 L360 L400 L440 Time(days)Standard Enclosure 501 N/A RGG 20Weatherproof Enclosure 502 N/A RGG 20

BASE

Mod Est. LeadCode RL210 RL250 L280 L320 L360 L400 L440 Time(days)

505 $328 $422 $604 $667 $781 $1,490 N/A DCT 3

BELTED DRIVE


Belted Drive 508 $427 $479 $531 $573 $615 $1,948 $2,656 RGG 35

BLOWER FILTERS

Mod Est. LeadCode RL210 RL250 L280 L320 L360 L400 L440 Time (days)

Filter 511 $500 DCT 3

BLOWER LOCATION

Mod Est. LeadCode RL210 RL250 L280 L320 L360 L400 L440 Time (days)

Blower Location ODE F1 512 $292 $292 $292 $292 $396 $438 $438 RGG 15Blower Location ODE F2 513 $292 $292 $292 $292 $396 $438 $438 RGG 15

For DPFV and TEAO-Piggy Back Blowers, blower location must be specified. Standard location for DPFV and TEAO-Piggy Back Blower is blower is Opposite Drive End Top mounting. Blower can be moved to ODE F1 or ODE F2. Cannot be located on same side as conduit box.

List PriceLocation

Monitors pressure differential between inside and outside of motor to actuate SPDT switch when pressure drops below preset value giving an immediate indication that the air supply to the motor is reduced. Applicable to forced ventilated motors with either motor mounted blower or separately forced ventilated by customer supplied air. Since motors dependent on force ventilation will have a rapid rise in temperature after the air supply is interrupted, the customer must take immediate corrective action when the switch trips. Contacts rated 15 amps, 120-480 volts, 60 Hz AC resistive; 1/8 HP at 125 volts; 1/4 HP at 250 volts, 60Hz AC. Applicable to frames RL210 thru L400.

$391 $693

LocationList Price

List PriceLocation

$609$891

Filter Addition for DPG-FV motor with motor mounted blower. Filter is washable type. Recommended when filterable contaminates are present. Totally enclosed construction rather than blower motor with filter (DPG-FV) is recommended for extremely dusty, dirty environments.

LocationList Price

Location

Note: Mounted on motor bracket at air inlet end.

Provides for roller bearings and special shaft on frames UL280-UL320 used for belted drive.

List Price


The lead time will be subject to the availability of stock motors and parts. The Modification Center is designed to process and ship units as quickly as possible; therefore, “Hold for Approval” and other similar conditions are not available on Modification Center orders. Typically, modifications will require 1 to 4 business days, once the order is entered. Orders for more than 5 units may require additional delivery time. The lead time shown on a Passport screen is for the base motor only, modifications will add to actual lead time. Many of the modification lead times are listed below.

Adjustable slide bases are used to adjust belt tension. Note: adjustable slide bases are not suitable for wall or ceiling mounting.

Heavy Duty Adjustable Slide Base


99

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Modifications Available to CM203 MotorsBLOWER TYPE

Mod Est. LeadEnclosure Modification Code RL210 RL250 L280 L320 L360 L400 L440 Time(days)TEBC Piggyback 514 $333 $469 $625 $833 $990 $1,333 na RGG 20

CONDUIT BOX Mod Est. Lead

Conduit Box Feature Code RL210 RL250 L280 L320 L360 L400 L440 Time(days)

515 $221 $221 $221 $276 $331 N/A N/A RGG 15

516 $221 $248 $348 $497 $596 N/A N/A RGG 15

517 $497 $497 $696 $994 $1,193 Std Std RGG 15

Auxiliary C/B 518 $216 $216 $393 $393 $393 $458 $458 RGG 15F1 520 $386 $386 $398 $398 $420 $464 $464 RGG 15F2 521 $386 $386 $398 $398 $420 $464 $464 RGG 15F3 (Top) 522 $386 $386 $398 $398 $420 $464 $464 RGG 15W5 (Wall Mount Vertical Shaft Up) 523 $386 $386 $398 $398 $420 $464 $464 RGG 15W6 (Wall Mount Vertical Shaft Down) 524 $386 $386 $398 $398 $420 $464 $464 RGG 15W7 (Wall Mount Vertical Shaft Down) 525 $386 $386 $398 $398 $420 $464 $464 RGG 15W8 (Wall Mount Vertical Shaft Up) 526 $386 $386 $398 $398 $420 $464 $464 RGG 15

COVERS (DPG-FV)Mod Est. LeadCode RL210 RL250 L280 L320 L360 L400 L440 Time(days)

Vertical Mount Drip Covers* 527 $65 $93 $141 $219 $380 $528 $528 RGG 10Splashproof Covers** 528 $331 $422 $422 $422 $422 $633 $633 RGG 10

DRAIN PLUGSMod Est. LeadCode RL210 RL250 L280 L320 L360 L400 L440 Time(days)

Automatic Breather Drain* 531 RGG 10Standard “T” Drain* 532 RGG 10

Nominal Brake (ft.-lbs) Sizes available 10,15,25,35,50,75,105

Table 1- Drive End- The Steams double C-Face 87,700 series brake can be mounted on the drive end of all the C-Face stock enclosures. Motor mounting positions,i.e. horizontal or vertical, must be specified on the order. Note: Drive end mounted brakes are not suitable for belted duty. Manual release - standard on all Steam brakes. Contact AB Control Matched Motor Marketing for custom quotes.

BRAKES

TEBC-Piggyback - For totally enclosed machines where blower motor must be on top or side of base motor housing, use the following pricing chart to add to TEAO inline price for top- or side-mounted blower and shroud for direct cooling air over base motor frame. Includes 3-phase 60 Hz 230/460 Volt AC Induction Motor.

List PriceLocation

Mill Type C/B* - (RL210 - L360), standard on all L400 & L440 frames

* Heavy gauge, large rectangular metal box. Standard on L400 and L440 frames.

** Conversion Conduit Box Mounting-See Standard Motor Feature section of catalog for standard conduit box locations.

List PriceLocation

One Size Larger C/B - (Not applicable on L400 - L440 frames)Cast Iron C/B - (Not applicable to L400 - L440

List PriceLocation

* Special bracket louvers designed to insure drip-proof protection for vertically operated foot or flange mounted motors.

** For dripproof machines to meet NEMA MG1 - 1.25.2 requirements for splashproof enclosures. Provides protection against liquid drops or solid particles from entering the motor at any angle not greater than 100 degrees downward from the vertical.

* Drain Plugs are at the lowest point of the motor.

List PriceLocation

$125$31


100

General

Information

CM

100C

M 200

CM

300F

ootnotes

Modifications Available to CM203 MotorsENCLOSURE MODIFICATION

Mod Est. LeadEnclosure Modification Code RL210 RL250 L280 L320 L360 L400 L440 Time(days)Separately Ventilated 535 ($531) ($759) ($1,050) ($1,318) ($1,444) ($1,734) ($2,119) RGG 10

Mod Est. LeadEnclosure Modification Code RL210 RL250 L280 L320 L360 L400 L440 Time(days)

537 $519 $696 $861 $1,159 $1,778 $2,264 $2,264 RGG 20

538 $858 $1,090 $1,388 $1,747 $2,304 $2,860 $2,860 RGG 20

END BRACKETS

Mod Est. LeadEnd Bracket Code RL210 RL250 L280 L320 L360 L400 L440 Time(days)

Nema210TC

Nema250TC

Nema280TC

Nema320TC

Nema360TC Not Avail. Not Avail.

C-FACE 542 $388 $464 $596 $839 $933 N/A N/A RGG 20Nema210T D Flange

Nema250T D Flange

Nema280T D Flange

Nema320T D Flange

Nema360T D Flange

Nema 400T D Flange

Nema440T D Flange

D-FLANGE 543 $718 $916 $1,049 $1,670 $2,124 $2,760 $2,760 RGG 20

Only NEMA C-Face or D-Flange bracket with standard dimensions and feet can be added for each NEMA frame.Special Seals required when oil will be around the shaft. C-Face available on frames RL210C thru L360C only. D-Flange only available on DPFV

NOTE: Prices above includes shaft changes if necessary to match NEMA Standards for chosen End Bracket.

Note: Since CM203 motors are designed for maximum horsepower per frame size, it is important to state the specific NEMA C-Face or D-Flange and shaft diameter required for mounting, when motor will be mounted to a reducer.

List PriceLocation

IMPORTANT: Motor C-Face is intended for mounting auxiliary equipment such as pumps, gears, etc. When mounted horizontally, frames L280C thru L360C & L400D thru L440D must be supported by the feet and not by the C-Face or D-Flange alone.

*Without encoder option, or when encoder is inherently suitable for mill and chemical duty. (See Feedback Devices.)**With an encoder not suitable for mill and chemical duty. To avoid exposed aluminum, MS connector is replaced with terminal block, mounted in auxiliary conduit box; encoder enclosed in sealed housing. Note: Price does not include encoder. Price does include adders for Auxiliary Conduit Box & Terminal Block for encoder leads.

List PriceLocation

Severe Duty Features without Severe Duty Encoder option*Severe Duty Features with Severe Duty Encoder option**

Motor accessories such as brakes must be specified and priced as totally enclosed construction for Severe Duty motors.Motors located in damp, moist environments must have space heaters to protect against condensation when the motor is not operating.Motors operating in dirty areas with fine abrasive dust such as taconite surrounding the motor should have dustproof/taconite featuresadded in addition to this modification.

NOTES REGARDING SEVERE DUTY MOTOR CONSTRUCTION:

Severe Duty Features (IP54) - (RL210 thru L440 frames) The Allen-Bradley Severe Duty motor is designed for operation in damp locations where the motor will be subjected to corrosive conditions. Typical applications are paper, chemical, petroleum, fertilizer and plastics industries. Severe Duty motors are provided in totally enclosed non-ventilated, totally enclosed fan-cooled and totally enclosed air-over construction. TEAO-BC will use a Severe Duty blower motor with longer blower housing than TEAO-BC standard.

Separately Ventilated - For applications where ventilated air is piped into the machine from an external source, basic DPG-FV enclosures may be separately ventilated at 3, 6, 9 and 12 o’clock for the below list price deductions. The inlet pipe can be fastened to one end bracket, and, if required and specified, an outlet pipe can be fastened to the other end bracket. Price does not include bloweror pipe. Locations of air entry and air exhaust, if used, should be specified on order. Motors must not be operated without the separate air supply. Refer to Application Data Section for separate ventilating air requirements. (To insure adequate protection of a separately ventilated motor against loss of cooling air, an overtemperature device for interlocking with the controller overload protection circuit is recommended and should be added as standard practice. An air pressure differential switch is also recommended.) See pricing deduction chart below.

List PriceLocation


101

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Modifications Available to CM203 MotorsFEEDBACK DEVICES -Mounted To Stock Motors (Price Includes Mounting)

PowerVDC

Max Op Temp.

MaxRPM Output

Est. Lead Time(days)

5-26v 70 C 6000 Single 205-26v 70 C 6000 Single 20

5-26v 70 C 3600 Single 205-26v 70 C 3600 Single 205-26v 70 C 3600 Dual 205-26v 70 C 3600 Dual 20


5-26v 80 C 3600 Single 20


5-18v 85 C 5000 Single 205-18v 85 C 5000 Dual 20

5-12v 75 C 3000 Single 25

5-12v 75 C 3000 Single 25

PowerVDC

Max Op Temp.

MaxRPM Output





*Requires Piggyback Blower for TEBC enclosure in frames RL210 - L400. No change for DPFV and TENV, RL210 - L400.

$3,708$5,229

US List Price for DPFV,TEBC,TENV

$5,229

574 n/a $2,802

$1,354

$3,594

$1,146

$1,406

$2,604

Dynapar HS-35 - A Photoelectric Encoder. Enclosure meets IP66. Comes standard with a 10 Pin Mating MS Connector. $1,1461024

1024 $3,594

$2,60410242048 $2,604

2048

$1,146552 2048 $1,146 $1,146551

1024 $1,406

557 $1,1461024

$2,802

$3,385

$3,708

558 2048 $1,146Lakeshore HS-35M (Magcoder) - A Magnetoresistive Encoder suitable for applications involving Grease, Oil, Water or Dirt. Enclosure meets IP65. Comes standard with a 10 Pin Epic Style Industrial Connector.

566

Avtron HS-M4* - A Magnetoresistive Encoder suitable for Heavy Mill Duty applications. Enclosure is Liquid & Dust tight, and a Stainless Steel Breather Drain is supplied. Comes standard with a 10 Pin Industrial Connector.

561

BEI HS-35 - A Photoelectric Encoder suitable for applications involving Robotics, Oil Service & Web Process Control. Enclosure meets IP65. Comes standard with a 10 Pin Mating MS Connector.

$1,823$1,823

Stegmann SRS25* - A single turn, heavy duty sincos encoder ideal for positioning applications utilizing PF700S drives. Enclosure is rated IP66. Comes standard with 10 pin radial connector.

575 n/a $3,385

581 2048

554553 1024

HOLLOWSHAFT ENCODERS - Mount on motor stub shaft with no coupling required. A tether-arm mounts to the motor end bracket to prevent rotation of the encoder stator, and also to protect against shaft currents. Standard output is two channels (A & B), quadrature with complementary outputs.

PPRUS List Price for

DPFV,TEBC,TENVUS List Price for

TEFCDescriptonMod Code

Dynapar HS-20 - A Photoelectric Encoder. Enclosure meets IP65. Comes standard with a 10 pin mating MS connector.

$1,031

$1,146

$1,823

$1,031548

$1,823

547 10242048 $1,031

$1,031

567 $3,594$3,5942048

COUPLED ENCODERS - Mounts to motor with the use of a stub shaft, flexible shaft coupling & flange adapter (flower pot). Standard Output is two channels (A & B), quadrature. All coupled encoders additions are performed at RGG.

Avtron HS-M3* - A Photoelectric Encoder suitable for Mill Duty applications. Enclosure is sealed against Dust & Water ingress. Comes standard with a 10 Pin Industrial Connector.

564565 $2,604

Stegmann SRM25* - A multi turn, heavy duty sincos encoder ideal for positioning applications utilizing PF700S drives. Enclosure is rated IP66. Comes standard with 10 pin radial connector.

10241024

570571

US List Price for TEFC

Not Available

Dynapar H20 - A Photoelectric Encoder suitable for Industrial Motion applications. Enclosure meets IP66. All Dynapar encoders are CE labeled.

580 1024 $1,354 Not Available

PPRDescriptonMod Code


Allen Bradley 845H - A Photoelectric Encoder suitable for Industrial applications. Enclosure meets IP66.

585 2048 $1,927 Not Available584 1024 $1,927 Not Available

Avtron M3* - A Photoelectric Encoder suitable for Mill Duty applications. Enclosure is sealed against Dust & Water ingress. Comes standard with a 10 Pin Industrial Connector.




102

General

Information

CM

100C

M 200

CM

300F

ootnotes

Modifications Available to CM203 Motors




5-12v 75 C 3000 Single 255-12v 75 C 6000** Single 25

5-12v 75 C 3000 Single 255-12v 75 C 6000** Single 25

PowerVDC

Max Op Temp.

MaxRPM Output






*Requires Piggyback Blower Modification (-514) for TEBC enclosure in frames RL210 - L400. No mod required for DPFV and TENV, or TEBC L440.

617 n/a $3,385 Not Available

613 n/a $2,802 Not AvailableStegmann SRM25* - A multi turn, heavy duty sincos encoder ideal for positioning applications utilizing PF700S drives. Enclosure is rated IP66. Comes standard with 10 pin radial connector.



BEARINGLESS ENCODERS - Mounts directly to the motor stub shaft without bearings or couplings. The Pulse Wheel of this type of encoder mounts directly to the motor stub shaft, which is then encased by the bracket of the encoder.

DescriptonMod Code PPR

US List Price for DPFV,TEBC,TENV


Lakeshore RL67** - A Magnetoresistive Encoder suitable for Mill Duty applications. Enclosure allows for heavy machine vibration and accidental impacts. The RL67 adds only 1.5 inches to overall motor length. Comes standard with 10 Pin Epic Style Industrial Connector.



Avtron M4* - A Magnetoresistive Encoder suitable for heavy duty mill applications. Enclosure is liquid and dust tight. A stainless steel breather drain is supplied. Comes standard with 10 Pin industrial connector



Dynapar H56*- A direct replacement for the RD62 for mill duty applications. The H56 is a Photoelectric Encoder suitable Severe Duty Applications. Enclosure meets IP66. All Dynapar encoders are CE labeled.



Avtron M485* - A Magnetoresistive Encoder suitable for Severe Duty applications. Enclosure is sealed against Dust & Water ingress. Comes standard with a 10 Pin Industrial Connector.



Stegmann SRS25* - A single turn, heavy duty sincos encoder ideal for positioning applications utilizing PF700S drives. Enclosure is rated IP66. Comes standard with 10 pin radial connector.


Lakeshore SL56* - A Magnetoresistive Encoder suitable for Mill Duty applications. Enclosure allows for heavy machine vibration and accidental impacts. Comes standard with 10 Pin Epic Style Industrial Connector.

624 1024 $1,719 Not Available625 2048 $1,719 Not Available626 1024 $3,333 Not Available627 2048 $3,333 Not Available

Lakeshore SL85* - A Magnetoresistive Encoder suitable for Mill Duty applications. Enclosure allows for heavy machine vibration and accidental impacts. The SL85 adds only 1.25 inches to overall motor length. Comes standard with 10 Pin Epic Style Industrial Connector.


Lakeshore RIM8500* - A Magnetoresistive Encoder suitable for Rugged Mill Duty applications. Enclosure is made of Ductile Cast Iron. Comes standard with 10 Pin Epic Style Industrial Connector.



103

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es




INSULATION SYSTEMMod Est. Lead

Insulation Code RL210 RL250 L280 L320 L360 L400 L440 Time(days)Tropical Protection 658 $186 $311 $480 $823 $1,111 $1,399 $2,302 RGG 20

LUBRICATION


Auto Grease Relief Fittings 661 10

List Price Location2,455$

2,741$

2,800$

2,990$

4,420$

4,816$

List PriceLocation

Note: Standard CM203 motors utilize an advanced insulation system that provides excellent protection against fungus and high humidity as found in tropical climates. The standard motor is suitable for operation in tropical climates without additional treatment. For additional protection, especially during shipment and prolonged storage, this modification provides a fungicidal air dry varnish treatment per MIL-V-173C (Type I Treatment) applied over all motor windings. Motors applied in highly corrosive, moist and dirt-laden environments should have an enclosure with Severe Duty features to limit the entrance of contaminants into the motor.

Grease - Ball Bearings furnished in RL210 - L440 Frame CM203 motors are lubricated with Chevron SRI-2 Grease. RL210 - L440 CM203 motors have Rockwell Automation’s exclusive “PLS” System. RL210-R250 frame RPM AC motors come standard with “Lubed-For-Life” bearing system.

Resolver 800123-2R, used with 1750 rpm motors (TS2014N) Avail. TEBC-In-Line L210-L400 Flange Mtg (AJ=2.913)Resolver 800123-2S, used with motor top speeds of 1150 rpm and less. Avail. TEBC-In-Line L210-L400 Flange Mtg (AJ=2.913)

RGG

Resolver 800123-S, used with motor with top speeds of 1150 rpm and less. Requies Piggyback Blower for TEAO-BC designs.

Resolver 800123-T, sometimes used with motors with top speeds of 500rp, and less. Requires Piggyback Blower for TEAO-BC designs.

Fittings - Alemite fittings are provided as standard on L280 - L440 frames.Automatic Grease Relief Fittings - Two Automatic Relief Fittings can be furnished on modified L280 - L440 frame motors.

Resolvers- A resolver is a shaft angle sensing transducer. Interfacing with an imput module, the resolver provides position and velocity feedback information to the Control System. Three outputs are avaliable to meet application requirements. Resolvers are provided in industrial duty and heavy duty industrial inclosures and can be face or foot mounted. Heavy duty resolvers with double shaft extentions can be supplied when a second feedback device such as an overspeed switch is required mounted in line. The table below defines the avaliable outputs and mounting arrangements. The price includes mounting of the resolver to the motor. Contact AB Control Matched Motor Marketing for custom quote.

RESOLVERS

List PriceLocation

$31

Lakeshore RIM1250* - A Magnetoresistive Encoder suitable for Rugged Mill Duty applications. Enclosure is made of Ductile Cast Iron. Comes standard with 10 Pin Epic Style Industrial Connector.


Avtron M285* - A Magnetoresistive Encoder suitable for Heavy Mill Duty applications. Enclosure is made of a Heavy Duty Cast Housing. Comes standard with 10 Pin Epic Style Industrial Connector.


512 $5,573 Not Available649 1024 $4,156 Not Available

*Requires Piggyback Blower Modification (-514) for TEBC enclosure in frames RL210 - L400. No mod required for DPFV and TENV, or TEBC L440.

651 1024 $5,573 Not Available650

Resolver 800123-R, used with 1750 rpm motors. Foot and 56 C-Face mounting. Required Piggyback Blower for TEAO-BC designs.

Resolver 800123-2T, sometimes used with motors with top speeds of 500 rpm and less. Avail. TEBC-In-Line L210-L400 Flange Mtg (AJ=2.913)


104

General

Information

CM

100C

M 200

CM

300F

ootnotes

Modifications Available to CM203 Motors2R 2S 2T R S TX X

X XX X

X X XX X X

X X X X X X

X X XX X X

X X X X X X

SHAFT SEALSMod Est. Lead

Shaft Seal Code RL210 RL250 L280 L320 L360 L400 L440 Time(days)Lip Seal* 674 RGG 10

SPACE HEATERS


Space Heater - 120v 1ı- 677 RGG 15Space Heater - 230v 1ı- 678 RGG 15Space Heater - 460v 1ı- 679 RGG 15Space Heater Aux. C/B* 680 RGG 15

TERMINAL BLOCKS


Main Terminal Block 683 $292 $365 $479 $635 $781 $1,031 $1,031 RGG 15Accessory Terminal Block* 684 RGG 15

TESTS


687 RGG 10

688 $313 $417 $521 $625 $729 $833 $938 RGG 15

689 $1,250 $1,563 $1,667 $1,875 $2,188 $3,333 $4,688 RGG 15

690 $1,875 $2,500 $2,604 $2,813 $3,333 $5,104 $6,771 RGG 20

Flange Mount

RESOLVER PART NO - 800123-1X (360º electrical = 360º mechanical)2X (360º electrical = 180º mechanical)5X (360º electrical = 72º mechanical)

List PriceLocation

$497 $1,038

* This modification provides a lip seal on the drive end to protect the bearing when operated with oil splashing against the shaft. Typical application is on a horizontal motor mounted to a gear case where the stationary oil level is below the motor shaft. CAUTION: Seals operated dry for extended periods will be damaged. LIST PRICE IS BASED PER BEARING.

List PriceLocation

Space heaters mounted inside the motor. Recommended to prevent condensation of moisture for motors remaining unenergized for long periods of time. Standard heater is single phase, 50/60 Hz. Leads are terminated in motor conduit boxes.

$303

*Separate conduit box for space heater leads and accessories.

$303$303

$216 $393 $458

Provides terminal block in main conduit box for connection of CM203 motor power leads, instead of the standard leads with terminal lugs. Thermostat leads will not be connected to the terminal block.

List PriceLocation

$104

*Provides terminal block in auxiliary conduit box for connection of pulse tachometer or digital encoder. Includes conduit box.

Tests - As standard practice, every CM203 motor is full load check tested on a dynamometer with a PWM power supply, and receivesa Routine Test per IEEE 112 as modified by Rockwell Automation for inverter power supply.

List PriceLocation

*Provides complete performance test and heat run on PWM inverter power per IEEE 112 as modified by Rockwell Automation for operation on inverter.

$104Certified Routine Test Report -UnwitnessedCertified Routine Test Report -WitnessedCertified Complete Test Report* - UnwitnessedCertified Complete Test Report* - Witnessed

Use with Flange Type Mounting Use with Scoop Mount

Foot Mount & C-FaceSingle ShaftDouble shaftGeneral Industrial DutyHeavy Industrial Duty


105

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Replacement Blower KitsFrame Enclosure Discription Approx. AB Model AB List

Type Weight Number PriceRL210 DPG-FV * CMKIT-417077-144 $813 RL250 DPG-FV * CMKIT-417077-145 $915L280 DPG-FV * CMKIT-419947-31 $1,159L320 DPG-FV * CMKIT-419947-33 $1,289L360 DPG-FV * CMKIT-419947-35 $1,473L400 DPG-FV * CMKIT-417077-75 $2,100

RL210-RL250 DPG-FV Includes Termninal Bob & Blower Motor CMKIT-417077-141 $596Discount Schedule 16

* Kit includes blower motor and shroud, blower wheel and all mounting hardware. Filter is not included.

FiltersFrame Enclosure Description Approx. AB Model AB List

Type Weight Number PriceRL210 DPFV Washable Wire Mesh Canister Type 5 CMKIT-417077-59 $403RL250 DPFV Washable Wire Mesh Canister Type 5 CMKIT-417077-59 $403L280 DPFV Washable Wire Mesh Canister Type 5 CMKIT-417077-59 $403L320 DPFV Washable Wire Mesh Canister Type 5 CMKIT-417077-59 $403L360 DPFV Washable Wire Mesh Canister Type 5 CMKIT-417077-65 $467L400 DPFV Washable Wire Mesh Canister Type 5 CMKIT-417077-102 $777L440 DPFV Square Replaceable Polyester Type 5 CMKIT-417077-124 $910



106

General

Information

CM

100C

M 200

CM

300F

ootnotes


EncodersFrame Enclosure Type Supply Output/PPR AB Model AB List

Type Voltage Number Price56,140,W180T TENV/TEBC Hollow Shaft/ Dynapar HS20 5-26 volts Single/1024 *CMKIT-K00T0006 $86756,140,W180T TENV/TEBC Hollow Shaft/ Dynapar HS35 5-26 volts Single/1024 *CMKIT-K00T0008 $1,19256,140,W180T TENV/TEBC Berringless/ Lakeshore SL56 5-15 volts Single/1024 CMKIT-K00T0005 $1,625

RL210-250 DPVF Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417077-136 $1,192L280-L400 DPVF Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417708-130 $1,192

L440 DPVF Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417708-132 $1,192RL210-250 DPVF Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417077-140 $1,463L280-L400 DPVF Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417708 -220 $1,463

L440 DPVF Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417708 -221 $1,463RL210-250 DPVF Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417077-153 $1,408L280-L400 DPVF Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417708-85 $1,408

L440 DPVF Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417708-121 $1,408RL210-250 DPVF Northstar Berringless/ RL67 5-15 volts Single/1024 CMKIT-417077-156 $1,733L280-L400 DPVF Northstar Berringless/ RL67 5-15 volts Single/1024 CMKIT-417708-87 $1,733

L440 DPVF Northstar Berringless/ RL67 5-15 volts Single/1024 CMKIT-417708-120 $1,733RL210-250 DPVF Northstar Berringless/ SL85 5-15 volts Single/1024 CMKIT-417708-226 $2,113L280-L400 DPVF Northstar Berringless/ SL85 5-15 volts Single/1024 (4) $2,113

L440 DPVF Northstar Berringless/ SL85 5-15 volts Single/1024 (4) $2,113 RL210-250 TENV Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417077-136 $1,192 RL210-250 TENV Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417077-140 $1,463 RL210-250 TENV Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417077-153 $1,408 RL210-250 TENV Northstar Berringless/ RL67 5-15 volts Single/1024 CMKIT-417077-156 $1,733 RL210-250 TENV Northstar Berringless/ SL85 5-15 volts Single/1024 CMKIT-417708-226 $2,113

RL210 TEBC Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417077-134 $1,192 RL250 TEBC Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417077-135 $1,192L280 TEBC Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417708-131 $1,192L320 TEBC Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417708-140 $1,192L360 TEBC Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417708-141 $1,192L400 TEBC Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417708-142 $1,192



Type Voltage Number Price RL210 TEBC Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417077-138 $1,463 RL250 TEBC Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417077-139 $1,463L280 TEBC Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417708-222 $1,463L320 TEBC Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417708-223 $1,463L360 TEBC Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417708-224 $1,463L400 TEBC Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417708-225 $1,463

RL210 TEBC Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417077-151 $1,408 RL250 TEBC Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417077-152 $1,408L280 TEBC Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417708-90 $1,408L320 TEBC Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417708-91 $1,408L360 TEBC Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417708-92 $1,408L400 TEBC Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417708-93 $1,408

RL210 TEBC Northstar Berringless/ RL67 5-15 volts Single/1024 CMKIT-417077-157 $1,733 RL250 TEBC Northstar Berringless/ RL67 5-15 volts Single/1024 CMKIT-417077-159 $1,733L280 TEBC Northstar Berringless/ RL67 5-15 volts Single/1024 CMKIT-417708-96 $1,733



107

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Type Voltage Number PriceL320 TEBC Northstar Berringless/ RL67 5-15 volts Single/1024 CMKIT-417708-97 $1,733L360 TEBC Northstar Berringless/ RL67 5-15 volts Single/1024 CMKIT-417708-98 $1,733L400 TEBC Northstar Berringless/ RL67 5-15 volts Single/1024 CMKIT-417708-99 $1,733

RL210 TEBC Northstar Berringless/ SL85 5-15 volts Single/1024 CMKIT-417708-227 $2,492 RL250 TEBC Northstar Berringless/ SL85 5-15 volts Single/1024 CMKIT-417708-227 $2,492L280 TEBC Northstar Berringless/ SL85 5-15 volts Single/1024 (4) $2,492L320 TEBC Northstar Berringless/ SL85 5-15 volts Single/1024 (4) $2,492L360 TEBC Northstar Berringless/ SL85 5-15 volts Single/1024 (4) $2,492L400 TEBC Northstar Berringless/ SL85 5-15 volts Single/1024 (4) $2,492

RL210 TEFC Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417077-133 $1,192RL250 TEFC Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417077-133 $1,192RL210 TEFC Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417077-137 $1,463RL250 TEFC Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417077-137 $1,463RL210 TEFC Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417077-154 $2,589RL250 TEFC Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417077-155 $2,589L440 TEAO-PB Hollow Shaft/ BEI HS35 5-15 volts Single/1024 CMKIT-417708-132 $1,192L440 TEAO-PB Hollow Shaft/ Northstar HS 35M 5-26 volts Single/1024 CMKIT-417708-221 $1,463L440 TEAO-PB Coulped/ Dynapar H20 5-15 volts Single/1024 CMKIT-417708-121 $1,408L440 TEAO-PB Northstar Berringless/ RL67 5-15 volts Single/1024 CMKIT-417708-120 $1,733L440 TEAO-PB Northstar Berringless/ SL85 5-15 volts Single/1024 (4) $2,492

RL210-L440 TENV, DPFV BEI HS35 5-24 volts Single/2048 CMKIT-417708-230 $1,083RL210-L440 TEBC BEI HS35 5-24 volts Single/2048 CMKIT-417708-231 $1,083RL210-L440 TEFC BEI HS35 5-24 volts Single/2048 CMKIT-417708-232 $1,083


(4) Kit not available but can be ordered as a modification to Stock model motor, 2-3 week lead time typical

(*) Encoder requires Blower Kit-CMKIT-K00T0003, AB Price $433

(1) Note; encoder addition requires an extended blower cover on TEBC motors in all frames except L320. Cover is included in Complete kits only.


108

General

Information

CM

100C

M 200

CM

300F

ootnotes


Slide BasesFrame AB Model Dimension Sheet Approximate AB List

Number Weight PriceRL2153 CMKIT-419914-10A (1) 609957-10 30 $293RL2158 CMKIT-419914-10B (1) 609957-10 30 $293RL2162 CMKIT-419914-10D 609957-10 30 $293RL2168 CMKIT-419914-10L 609957-10 35 $341RL2173 CMKIT-419914-10M 609957-10 35 $341RL2570 CMKIT-419914-10G 609957-10 50 $341RL2578 CMKIT-419914-10N 609957-10 50 $439RL2586 CMKIT-419914-10P 609957-10 50 $439L2875 CMKIT-419914-10J (1) 609957-10 50 $439L2882 CMKIT-419914-10K 609957-10 50 $628L2890 CMKIT-419914-10R 609957-10 50 $628L2898 CMKIT-419914-10S 609957-10 50 $628L3203 CMKIT-419914-11P 609977-10 90 $693L3213 CMKIT-419914-11R 609977-10 90 $693

UL3698 CMKIT-419914-11M 609977-10 105 $813UL3699 CMKIT-419914-11C 609977-10 105 $813UL3607 CMKIT-419914-11D 609977-10 110 $813UL4022 CMKIT-419914-11E 609977-10 123 $1,549UL4034 CMKIT-419914-11F 609977-10 123 $1,549UL4046 CMKIT-419914-11G 609977-10 123 $1,549UL4429 CMKIT-419914-11H $2,925UL4440 CMKIT-419914-11J $2,925UL4451 CMKIT-419914-11K $2,925UL4461 CMKIT-419914-11L $2,925


(1) Part number to be discontinued


109

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Stub ShaftsFrame For use with Enclosure AB Model AB List

encoder type: Type Number PriceRL210-RL250 BEI HS35 DPFV,TENV,TEFC,TEBC(1) CMKIT-417708-201 $108

L280-L400 BEI HS35 DPFV&TEBC(1) CMKIT-417708-202 $108L440 BEI HS35 DPFV&TEAO-P/B CMKIT-417708-203 $108

RL210-RL250 Dynapar H20 DPFV,TENV&TEBC(1) CMKIT-417708-204 $108RL250 Dynapar H20 TEFC CMKIT-417708-205 $108

L280-L400 Dynapar H20 DPFV CMKIT-417708-207 $108L280-L400 Dynapar H20 TEBC(1) CMKIT-417708-206 $108

L440 Dynapar H20 DPFV&TEAO-P/B CMKIT-417708-206 $108RL210-RL250 SL85 DPFV,TENV&TEBC(1) CMKIT-417708-210 $108

L280-L440 SL85 DPFV & TEBC(1) CMKIT-417708-212 $108L440 SL85 DPFV&TEAO-P/B CMKIT-417708-212 $108

RL210-RL250 RL67 DPFV,TENV&TEBC(1) CMKIT-417708-208 $108L280-L400 RL67 TEBC(1) CMKIT-417708-209 $108L280-L400 RL67 DPFV CMKIT-417708-42 $117

L440 RL67 DPFV&TEAO-P/B CMKIT-417708-157 $146Discount Schedule 16

(1) Note; encoder addition requires an extended blower cover on TEBC motors in all frames except L320. Cover is included in Complete kits only.

Stub shaft only (no encoder) - unmounted - for frames RL210-L440All HS35 stub shaft diameters: 1 inch


110

General

Information

CM

100C

M 200

CM

300F

ootnotes


Architecture ClassIndustrial Environment SeriesCM205 Family - Laminated Steel Frame DC Motors

5-800 HPC210ATZ-C500ATZ Frames,GK112-GS315 Frames (IEC)CM205 Family DC Motors combine the best features of the Rockwell Automation RPM™ and SUPER RPM™ DC Motors with new advances in design and construction. CM205 Family DC Motors provide more power, reliability and easier serviceability in a smaller package.

CM205 Family DC Motors are the third generation of Rockwell Automation motors specifically "Performance Matched" for variable speed applications utilizing rectified power. Here's why this enhanced product is ideally suited to meet today's and tomorrow's most demanding industrial requirements.

• End brackets with integral feet provide more rigid mounting

• Higher HP ratings per frame size• Quicker response, higher torque to inertia ratio• Smooth operation at low speeds• Laminated frame, sharply reduced eddy currents• Wider speed range capability• Longer brush life, better commutation• Simplified installation and service accessibility• Exclusive PLS® lubrication system• Specifically designed for rectified power

New, larger armature diameters provide a significant increase in rating per frame size and improved torque-to-inertia ratios for quick response. Skewed armature designs also ensure smooth operation at low speeds.

Four-pole configuration extends speed ranges, improves linear torque-per-amp relationship and contributes to smoother, quicker response.

Field-proven square laminated frame constructionimproves commutation and heat dissipation, and requires less mounting space than round body motors.Mechanically held commutator provides dynamic stability, eliminating high or low bars and undesirable thermal stress.Computer designed frame and bracket eliminate vibration at any speed within the motor's operating range and prevent the motor from being excited by harmonics in the rectified power supply. End brackets are cast iron with integral mounting feet, providing a rigid, vibration-resistant mechanical enclosure.Radial brush holders with a unique pivoting brush finger and a constant-tension coiled spring ensure positive, continuous contact between the brush and commutator. This results in optimum commutation and better utilization of the brush length for up to twice the brush life.Rotatable brush rigging assembly provides easier access to top and bottom brushes. (Access is through large hand hole openings in the side of the motor.)PLS lubrication system uses open bearings that run cooler for long life. Unique configuration of bearing cavity ensures proper bearing lubrication regardless of motor mounting position. It also eliminates possibility of damage to the motor or bearings due to overgreasing.CM205 Family DC Motors are manufactured of quality materials with continual quality assurance of processes. CM205 Family, NEMA and IEC DC motors are manufactured in ISO 9001 certified facilities.

CM205 PERFORMANCE ADVANTAGES:

CM205 ADVANCED DESIGN FEATURES:

CM205 Family - Laminated Steel Frame DC Motors

111

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


CM205 Family DC Motors

* Blower located on drive end

XEXE

XOXO

POS.POS.

EE

4 4POS.POS.

NN

VV

AA

EE

UU

22

POS. 1POS. 1

POS. 3POS. 3

CC

KK

BKBK2F2F

FKFK

AIRAIRINLETINLET

FVFV

FILTERFILTERSUPPLIEDSUPPLIEDONLY WHENONLY WHENSPECIFIED.SPECIFIED.

FUFU

GUARDGUARD

BABA

DD

Frame E A 2F K BK BAC

D XE XODrive End Non-Drive End Approx.

WeightSTD LG V N U FV FUSC2113 4.25 10.25 18.00 5.19 2.38 3.50 28.38 - 5.25 10.00 22.75 3.50 4.00 1.875 3.00 1.625 345MC2113 4.25 10.25 18.00 5.19 2.38 3.50 29.62 - 5.25 10.00 22.75 3.50 4.00 1.875 3.00 1.625 370LC2113 4.25 10.25 18.00 5.19 2.38 3.50 31.25 - 5.25 10.00 22.75 3.50 4.00 1.875 3.00 1.625 400MC2115 4.25 10.25 22.00 5.19 2.38 3.50 32.50 - 5.25 10.00 22.75 3.50 4.00 1.875 3.00 1.625 425LC2115 4.25 10.25 22.00 5.19 2.38 3.50 35.25 - 5.25 10.00 22.75 3.50 4.00 1.875 3.00 1.625 480SC2512 5.00 12.31 20.00 6.06 3.00 4.25 31.69 - 6.25 9.50 24.75 4.00 4.50 2.125 3.50 1.875 535MC2512 5.00 12.31 20.00 6.06 3.00 4.25 33.19 - 6.25 9.50 24.75 4.00 4.50 2.125 3.50 1.875 570LC2512 5.00 12.31 20.00 6.06 3.00 4.25 34.69 - 6.25 9.50 24.75 4.00 4.50 2.125 3.50 1.875 610C2514 5.00 12.31 25.00 6.06 3.00 4.25 38.44 - 6.25 9.50 24.75 4.50 5.00 2.375 3.50 1.875 695C2515 5.00 12.31 28.00 6.06 3.00 4.25 42.44 - 6.25 9.50 24.75 4.50 5.00 2.375 3.50 1.875 805MC2812 5.50 13.78 22.00 6.75 3.50 4.75 37.38 - 7.00 9.25 26.75 4.50 5.00 2.375 4.00 2.125 810UMC2812 5.50 13.78 22.00 6.75 3.50 4.75 37.88 - 7.00 9.25 26.75 5.00 5.50 2.625 4.00 2.125 815LC2812 5.50 13.78 22.00 6.75 3.50 4.75 39.62 - 7.00 9.25 26.75 4.50 5.00 2.375 4.00 2.125 885ULC2812 5.50 13.78 22.00 6.75 3.50 4.75 40.12 - 7.00 9.25 26.75 5.00 5.50 2.625 4.00 2.125 890C2813 5.50 13.78 25.00 6.75 3.50 4.75 41.25 - 7.00 9.25 26.75 4.50 5.00 2.375 4.00 2.125 940UC2813 5.50 13.78 25.00 6.75 3.50 4.75 41.75 - 7.00 9.25 26.75 5.00 5.50 2.625 4.00 2.125 945C2815 5.50 13.78 32.00 6.75 3.50 4.75 46.75 - 7.00 9.25 26.75 4.50 5.00 2.375 4.00 2.125 1125UC2815 5.50 13.78 32.00 6.75 3.50 4.75 47.25 - 7.00 9.25 26.75 5.00 5.50 2.625 4.00 2.125 1130SC3210-LSC3210 6.25 15.50 20.00 6.75 4.00 5.25 36.25 38.75 8.00 8.50 28.00 5.00 5.50 2.625 4.25 2.250 1115USC3210-ULSC3210 6.25 15.50 20.00 6.75 4.00 5.25 36.75 39.25 8.00 8.50 28.00 5.50 6.00 2.875 4.25 2.250 1120MC3212-LMC3212 6.25 15.50 25.00 6.75 4.00 5.25 39.25 41.75 8.00 8.50 28.00 5.00 5.50 2.625 4.25 2.250 1210UMC3212-ULMC3212 6.25 15.50 25.00 6.75 4.00 5.25 39.75 42.25 8.00 8.50 28.00 5.50 6.00 2.875 4.25 2.250 1215LC3212-LLC3212 6.25 15.50 25.00 6.75 4.00 5.25 41.25 43.75 8.00 8.50 28.00 5.00 5.50 2.625 4.25 2.250 1290ULC3212-ULLC3212 6.25 15.50 25.00 6.75 4.00 5.25 41.75 44.25 8.00 8.50 28.00 5.50 6.00 2.875 4.25 2.250 1295C3214-LC3214 6.25 15.50 32.00 6.75 4.00 5.25 46.25 48.75 8.00 8.50 28.00 5.00 5.50 2.625 4.25 2.250 1470UC3214-ULC3214 6.25 15.50 32.00 6.75 4.00 5.25 46.75 49.25 8.00 8.50 28.00 5.50 6.00 2.875 4.25 2.250 1475MC3612-LMC3612 7.00 17.50 28.00 7.25 4.62 5.88 42.88 44.62 9.00 10.88 29.87 5.50 6.00 2.875 5.50 2.875 1685UMC3612-ULMC3612 7.00 17.50 28.00 7.25 4.62 5.88 43.62 45.38 9.00 10.88 29.87 6.25 6.75 3.250 5.50 2.875 1695LC3612-LLC3612 7.00 17.50 28.00 7.25 4.62 5.88 46.62 48.38 9.00 10.88 29.87 5.50 6.00 2.875 5.50 2.875 1850ULC3612-ULLC3612 7.00 17.50 28.00 7.25 4.62 5.88 47.38 49.12 9.00 10.88 29.87 6.25 6.75 3.250 5.50 2.875 1860C3613-LC3613 7.00 17.50 32.00 7.25 4.62 5.88 50.12 51.88 9.00 10.88 31.62 5.50 6.00 2.875 5.50 2.875 2010UC3613-ULC3613 7.00 17.50 32.00 7.25 4.62 5.88 50.88 52.62 9.00 10.88 31.62 6.25 6.75 3.250 5.50 2.875 2020C4011 8.00 19.38 28.00 8.75 5.25 6.62 52.19 - 10.00 8.69 33.62 7.00 7.62 3.625 7.00 3.625 2500UC4011 8.00 19.38 28.00 8.75 5.25 6.62 53.19 - 10.00 8.69 33.62 8.00 8.62 4.125 7.00 3.625 2505MC4013 8.00 19.38 36.00 8.75 5.25 6.62 56.94 - 10.00 8.69 33.62 7.00 7.62 3.625 7.00 3.625 2800UMC4013 8.00 19.38 36.00 8.75 5.25 6.62 57.94 - 10.00 8.69 33.62 8.00 8.62 4.125 7.00 3.625 2805LC4013 8.00 19.38 36.00 8.75 5.25 6.62 60.19 - 10.00 8.69 33.62 7.00 7.62 3.625 7.00 3.625 3100ULC4013 8.00 19.38 36.00 8.75 5.25 6.62 61.19 - 10.00 8.69 33.62 8.00 8.62 4.125 7.00 3.625 3105C4412* 9.00 21.65 36.00 9.44 5.12 7.50 58.32 - 11.00 11.94 43.75 7.00 7.62 3.625 7.00 3.625 3245C4413* 9.00 21.65 40.00 9.44 5.12 7.50 62.25 - 11.00 11.94 43.75 7.00 7.62 3.625 7.00 3.625 3660LC4414* 9.00 21.65 45.00 9.44 5.12 7.50 68.56 - 11.00 11.94 43.75 7.00 7.62 3.625 7.00 3.625 4280


112

General

Information

CM

100C

M 200

CM

300F

ootnotes


CM205 Family DC Motor Overview

• The result of over 90 years of variable-speed application experience from the recognized global leader in DC performance and technology.

• Manufactured in an ISO 9001 certified facility for domestic and global markets.• Large armature with improved torque-to-inertia ratio provides fast response to speed changes.• Laminated frame reduces eddy currents and improves commutation over wide speed range.• Square cross section provides much greater power density for each frame size.

Available Features

DPG & DPG-FV Description

CM205 Family motors, the first DC motor designed to operate from solid-state rectified power are built to take on the industry’s toughest jobs.

Features• Unique laminated square frame for better performance. The square configuration packs up to 20% more active

material into the same space as a round frame of equivalent shaft height.• All motors are F1 construction unless otherwise specified• Armature and field windings designed and tested to insure trouble-free operation• PLS™ (Positive Lubrication System) for longer bearing and motor life• 2 year limited warranty

MountingEnclosure Type

Stock Horsepower Range

Integral end-bracket mounting feet DPG, DPG-FV, TEFC, TEDC-AA, TEDC-AW, TENV, XP, Extruder Duty, Paper Mill Duty 3-800


113

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Architecture Class, Industrial Environment Series

CM205 - Laminated Steel Frame DC MotorsDPG-FV IP23

Foot Mounted & C-Face Foot Mounted Enclosed IP44Enclosure HP Speed- RPM Field Pwr. Frame Norm US List Catalog String Notes

Base CHP Arm Field Winding Code Stock Price CM206-DPG 3 1750 1750 180 100/200 STR K DC189ATCY Yes $2,053 DG00317LXZCA 80,83,110

DPG 3 1750 1750 180 100/200 STR K DC189ATCZ Yes $2,053 DG00317LXZCB 80,83,93

DPG 3 1750 2300 240 150 STAB D DC189ATCZ Yes $2,065 DG00317TXZCA 80,83,93

SPG 3 1750 2300 240 240 STAB C C1811ATCZ Yes $2,504 DP00317UXZCA 80,93,Range Drive

DPG 3 1750 2300 500 300 STR C C1811ATZ Yes $2,435 DG00317QXZHA 80

DPG 5 1750 1750 180 100/200 STR K DC1810ATCZ Yes $3,150 DG00517LXZCA 80,85,93

DPG 5 1750 2300 240 150 STAB D C1811ATCZ Yes $3,150 DG00517TXZCA 80,83,93

DPG 5 1750 2300 240 150 STAB D C1811ATZ Yes $3,024 DG00517TXZHA 80,83

SPG 5 1750 2300 240 240 STAB C C1811ATCZ Yes $3,395 DP00517UXZCA 80,93,Range Drive

DPG 5 1750 2300 500 300 STAB D C1811ATZ Yes $3,024 DG00517V XZHA 80

DPG 5 1750 2300 500 300 STR D C1811ATZ Yes $3,024 DG00517QXZHB 80

DPG 7.5 1750 2300 240 150 STAB D C1811ATZ Yes $3,654 DG7F517TXZHA 80,83

DPG 7.5 1750 2300 240 150 STAB D C1811ATCZ Yes $3,843 DG7F517TXZCA 80,83,94

SPG 7.5 1750 2300 240 240 STAB C C1812ATCZ Yes $4,214 DP7F517UXZCA 80,93,Range Drive

DPG 7.5 1750 2300 500 300 STAB D C1811ATZ Yes $3,654 DG7F517V XZHA 80

DPG 7.5 1750 2300 500 300 STR D C1811ATZ Yes $3,654 DG7F517QXZHB 80

DPG 10 1750 2300 240 150 STAB D C1812ATCZ Yes $4,356 DG01017TXZCA 80,84,94

DPG 10 1750 2300 240 150 STAB D C1812ATZ Yes $4,167 DG01017TXZHA 80,84

SPG 10 1750 2300 240 240 STAB D SC2113ATZ Yes $4,727 DP01017UXZHA 87,94,Range Drive

DPG-FV 10 500 3000 240 240 STR C LC2512ATZ Yes $14,782 FV01005NXZHA 85,Beamer Motor

DPG 10 1750 2300 500 300 STAB D C1812ATZ Yes $4,167 DG01017V XZHA 80,85

DPG 10 1750 2300 500 300 STR D C1812ATZ Yes $4,167 DG01017QXZHB 80,85

DPG-FV 10 1750 2300 500 300 STAB C SC2113ATZ Yes $7,085 FV01017V XZHA 79,82,84,87,Extruder Duty

DPG 15 1750 2300 240 150 STAB C SC2113ATZ Yes $5,018 DG01517TXZHA 87

DPG-FV 15 1750 2300 240 150 STR C SC2113ATZ Yes $6,076 FV01517MXZHA 84,87,88

DPG-FV 15 1750 2300 240 150 STAB C SC2113ATZ Yes $6,076 FV01517TXZHB 84,87,88

DPG-FV 15 1750 2300 240 150 STR D SC2113ATCZ Yes $6,369 FV01517MXZCA 84,87,88,94

DPG-FV 15 500 3000 240 240 STR C C2515ATZ Yes $17,229 FV01505NXZHA 84,Beamer Motor

DPG 15 1750 2300 500 150/300 STAB C SC2113ATZ Yes $5,018 DG01517PXZHA 87

DPG-FV 15 1750 2300 500 300 STR C SC2113ATZ Yes $6,076 FV01517QXZHA 84,87,88

DPG-FV 15 1750 2300 500 150/300 STAB C SC2113ATZ Yes $6,076 FV01517PXZHA 84,87,88

DPG-FV 15 1750 2300 500 300 STAB C SC2113ATZ Yes $8,185 FV01517V XZHB 79,84,87, Extruder Duty

DPG 20 1750 2300 240 150 STAB C LC2113ATZ Yes $5,758 DG02017TXZHA 87

DPG-FV 20 1750 2300 240 150 STR C SC2113ATZ Yes $6,816 FV02017MXZHA 84,87,88

DPG-FV 20 1750 2300 240 150 STAB C SC2113ATZ Yes $6,816 FV02017TXZHB 84,87,88

DPG-FV 20 1750 2300 240 150 STR D SC2113ATCZ Yes $7,109 FV02017MXZCA 84,87,88,94

DPG 20 1750 2300 500 150/300 STAB C MC2113ATZ Yes $5,758 DG02017PXZHA 87

DPG-FV 20 1750 2300 500 300 STR C SC2113ATZ Yes $6,816 FV02017QXZHA 6,84,87,88

DPG-FV 20 1750 2300 500 300 STR C SC2113ATZ Yes $6,816 FV02017QXZHB 84,87,88

DPG-FV 20 1750 2300 500 150/300 STAB C SC2113ATZ Yes $6,816 FV02017PXZHA 84,87,88

DPG-FV 20 1750 2300 500 300 STAB C MC2113ATZ Yes $9,072 FV02017V XZHC 79,82,84,87,Extruder Duty

DPG 25 1750 2300 240 150 STAB C LC2113ATZ Yes $7,114 DG02517TXZHA 87

DPG-FV 25 1750 2300 240 150 STR C MC2113ATZ Yes $7,540 FV02517MXZHA 84,87,88

DPG-FV 25 1750 2300 240 150 STAB C MC2113ATZ Yes $7,540 FV02517TXZHB 84,87,88

DPG 25 1750 2300 500 150/300 STAB C LC2113ATZ Yes $7,114 DG02517PXZHA 87

DPG-FV 25 1750 2300 500 300 STR C MC2113ATZ Yes $7,540 FV02517QXZHA 6,85,87,88

DPG-FV 25 1750 2300 500 300 STR C MC2113ATZ Yes $7,540 FV02517QXZHB 85,87,88

DPG-FV 25 1750 2300 500 150/300 STAB C MC2113ATZ Yes $7,540 FV02517PXZHA 85,87,88

DPG-FV 25 1750 2300 500 300 STAB C LC2113ATZ Yes $9,942 FV02517V XZHC 79,82,84,87,Extruder Duty

DPG 30 1750 2300 240 150 STAB C SC2512ATZ Yes $7,833 DG03017TXZHA 87

DPG-FV 30 1750 2300 240 150 STR C LC2113ATZ Yes $8,194 FV03017MXZHA 84,87,88

DPG-FV 30 1750 2300 240 150 STAB C LC2113ATZ Yes $8,194 FV03017TXZHB 84,87,88

DPG 30 1750 2300 500 150/300 STAB C SC2512ATZ Yes $7,833 DG03017PXZHA 87

DPG-FV 30 1750 2300 500 300 STR C LC2113ATZ Yes $8,194 FV03017QXZHA 6,84,87,88

DPG-FV 30 1750 2300 500 300 STR C LC2113ATZ Yes $8,194 FV03017QXZHB 84,87,88

DPG-FV 30 1750 2300 500 150/300 STAB C LC2113ATZ Yes $8,194 FV03017PXZHA 84,87,88

DPG-FV 30 1750 2300 500 300 STAB C SC2512ATZ Yes $10,726 FV03017V XZHA 79,82,84,87,Extruder Duty

DPG-FV 30 1150 1800 500 300 STR C LC2115ATZ Yes $10,354 FV03011QXZHC 85,87,88

DPG-FV 40 1750 2300 240 150 STR C LC2115ATZ Yes $9,748 FV04017MXZHA 6,84,87,88

DPG-FV 40 1750 2300 240 150 STAB C SC2512ATZ Yes $9,748 FV04017TXZHB 6,84,87,88

DPG 40 1750 2100 500 150/300 STAB D LC2512ATZ Yes $9,219 DG04017PXZHA 6,87

Voltage


114

General

Information

CM

100C

M 200

CM

300F

ootnotes

Enclosure HP Speed- RPM Field Pwr. Frame Norm US List Catalog String Notes

Base CHP Arm Field Winding Code Stock Price CM206-Voltage

DPG-FV 40 1750 2100 500 300 STR C MC2115ATZ Yes $9,748 FV04017QXZHA 84,87,88

DPG-FV 40 1750 2100 500 300 STR C MC2115ATZ Yes $9,748 FV04017QXZHB 6,84,87,88

DPG-FV 40 1750 2100 500 300 STAB C MC2115ATZ Yes $9,748 FV04017V XZHC 6,84,87,88

DPG-FV 40 1750 2100 500 300 STAB C MC2512ATZ Yes $12,801 FV04017V XZHD 6,79,82,84,87,Extruder Duty

DPG-FV 40 1150 2000 500 300 STR C LC2512ATZ Yes $12,047 FV04011QXZHA 85,87,88

DPG 50 1750 2100 500 150/300 STAB C MC2812ATZ Yes $10,534 DG05017PXZHA 6,87

DPG 50 1750 2100 500 150/300 STAB C MC2812ATZ Yes $10,534 DG05017PXZHB 87

DPG-FV 50 1750 2100 500 300 STR C LC2115ATZ Yes $10,942 FV05017QXZHA 84,87,88

DPG-FV 50 1750 2100 500 300 STR C LC2115ATZ Yes $10,942 FV05017QXZHB 6,84,87,88

DPG-FV 50 1750 2100 500 300 STAB C LC2115ATZ Yes $10,942 FV05017V XZHC 6,84,87,88

DPG-FV 50 1750 2100 500 300 STAB C LC2512ATZ Yes $14,025 FV05017V XZHD 6,79,82,84,87,Extruder Duty

DPG-FV 50 1150 1900 500 300 STR C C2514ATZ Yes $13,669 FV05011QXZHA 6,85,87,88

DPG 60 1750 2100 500 300 STAB C LC2812ATZ Yes $12,061 DG06017V XZHA 6,87



DPG-FV 60 1750 2100 500 150/300 STAB C LC2512ATZ Yes $12,331 FV06017PXZHA 6,84,87,88

DPG-FV 60 1750 2100 500 300 STAB C MC2812ATZ Yes $15,691 FV06017V XZHC 6,79,82,84,87,Extruder Duty



DPG-FV 75 1750 2100 500 300 STR C C2514ATZ Yes $14,252 FV07517QXZHB 84,87,88

DPG-FV 75 1750 2100 500 300 STAB C C2514ATZ Yes $14,252 FV07517V XZHC 6,84,87,88




DPG-FV 100 1750 2000 500 300 STR C C2515ATZ Yes $17,536 FV10017QXZHB 84,87,88

DPG-FV 100 1750 2000 500 300 STAB C C2515ATZ Yes $17,536 FV10017V XZHC 6,84,87,88

DPG-FV 100 1750 2100 500 300 STAB C MC3212ATZ Yes $21,937 FV10017V XZHD 6,79,82,84,87,Extruder Duty



DPG-FV 125 1750 2000 500 300 STAB C C2813ATZ Yes $20,521 FV12517V XZHB 6,84,87,88

DPG-FV 125 1750 2000 500 300 STR C UC2813ATZ Yes $21,130 FV12517QXZHC 5,6,84,87,88


DPG-FV 125 1150 2000 500 300 STR C UC3214ATZ Yes $25,666 FV12511QXZHA 5,6,84,87,88


DPG-FV 150 1750 2000 500 300 STAB C C2815ATZ Yes $23,419 FV15017V XZHB 6,84,87,88

DPG-FV 150 1750 2000 500 300 STR C UC2815ATZ Yes $24,032 FV15017QXZHC 5,6,84,87,88

DPG-FV 150 1750 2100 500 300 STAB C MC3612ATZ Yes $28,996 FV15017V XZHD 6,79,82,87,Extruder Duty

DPG-FV 150 1150 2000 500 300 STR C ULC3612ATZ Yes $29,624 FV15011QXZHA 5,6,85,87,88

DPG-FV 150 1150 2000 500 300 STR C ULC3612ATZ Yes $29,624 FV15011QXZHB 5,85,87,88

DPG-FV 200 1750 2100 500 300 STR C UC3214ATZ Yes $30,356 FV20017QXZHA 5,6,84,87,88

DPG-FV 200 1750 2100 500 300 STR C UC3214ATZ Yes $30,356 FV20017QXZHB 5,84,87,88

DPG-FV 200 1750 2100 500 300 STAB C UC3214ATZ Yes $30,356 FV20017V XZHC 5,6,84,87,88

DPG-FV 200 1750 2100 500 300 STAB C LC3612ATZ Yes $36,712 FV20017V XZHD 6,79,82,87,Extruder Duty


DPG-FV 250 1750 2100 500 300 STR C ULC3612ATZ Yes $36,782 FV25017QXZHA 5,6,85,87,88

DPG-FV 250 1750 2100 500 300 STR C ULC3612ATZ Yes $36,782 FV25017QXZHB 5,85,87,88

DPG-FV 250 1750 2100 500 150/300 STAB C ULC3612ATZ Yes $36,782 FV25017PXZHA 5,6,85,87,88

DPG-FV 250 1750 2100 500 300 STAB C C4011ATZ Yes $44,423 FV25017V XZHC 6,79,82,87,Extruder Duty




DPG-FV 300 1750 2000 500 300 STAB C LC3613ATZ Yes $43,777 FV30017V XZHC 6,85,87,88

DPG-FV 300 1750 2100 500 300 STAB C MC4013ATZ Yes $53,303 FV30017V XZHD 6,79,82,87,Extruder Duty



DPG-FV 400 1750 2000 500 150/300 STAB C MC4013ATZ Yes $59,842 FV40017PXZHA 6,85,87,88

DPG-FV 400 1750 2000 500 300 STAB C LC4013ATZ Yes $76,130 FV40017V XZHB 6,79,82,87,Extruder Duty

DPG-FV 400 1150 1600 500 300 STR C C4413ATZ Yes $71,128 FV40011QXZHA 6,79,85,87,88





115

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


General Information

Cancellation or Changes to an Order



AIR PRESSURE SWITCH

Mod Est. LeadSwitch Code C180-C210 C250 C280 C320 C360 C400 C440 Time(days)Standard Enclosure 501 N/A RGG 20Weatherproof Enclosure 502 N/A RGG 20

BLOWER FILTERS

Mod Est. LeadCode C180-C210 C250 C280 C320 C360 C400 C440 Time (days)

Filter 511 $500 DCT 3

BLOWER LOCATION

Mod Est. LeadCode C180-C210 C250 C280 C320 C360 C400 C440 Time (days)

Blower Location ODE F1 512 $292 $292 $292 $292 $396 $438 $438 RGG 15Blower Location ODE F2 513 $292 $292 $292 $292 $396 $438 $438 RGG 15

CONDUIT BOX Mod Est. Lead

Conduit Box Feature Code C180-C210 C250 C280 C320 C360 C400 C440 Time(days)

515 $51 $71 $118 $188 $234 N/A N/A RGG 15

516 $141 $234 $328 $469 $563 N/A N/A 15

517 $281 $469 $656 $938 $1,125 Std Std RGG 15

Auxiliary C/B 518 $216 $216 $393 $393 $393 $458 $458 RGG 15


The lead time will be subject to the availability of stock motors and parts. The Modification Center is designed to process and ship unitsas quickly as possible; therefore, “Hold for Approval” and other similar conditions are not available on Modification Center orders. Typically, modifications will require 1 to 4 business days, once the order is entered. Orders for more than 5 units may require additionadelivery time. The lead time shown on a Passport screen is for the base motor only, modifications will add to actual lead time. Many of the modification lead times are listed below.

Monitors pressure differential between inside and outside of motor to actuate SPDT switch when pressure drops below preset value giving an immediate indication that the air supply to the motor is reduced. Applicable to forced ventilated motors with either motor mounted blower or separately forced ventilated by customer supplied air. Since motors dependent on force ventilation will have a rapid rise in temperature after the air supply is interrupted, the customer must take immediate corrective action when the switch trips. Contacts rated 15 amps, 120-480 volts, 60 Hz AC resistive; 1/8 HP at 125 volts; 1/4 HP at 250 volts, 60Hz AC. Applicable to frames C180 thru C440.

List PriceLocation

$609$891

Note: Mounted on motor bracket at air inlet end.

Filter Addition for DPG-FV motor with motor mounted blower. Filter is washable type. Recommended when filterable contaminates are present. Totally enclosed construction rather than blower motor with filter (DPG-FV) is recommended for extremely dusty, dirty environments.

List PriceLocation

$391 $693

For DPFV, blower location must be specified. Standard location for DPFV and is blower is Opposite Drive End Top mounting. Blower can be moved to ODE F1 or ODE F2. Cannot be located on same side as conduit box.

List PriceLocation

List PriceLocation

One Size Larger C/B - (Not applicable on DC180, DC2112, C400 - C440 Cast Iron C/B - (Not applicable to C400 - C440 Mill Type C/B* - (Not Applicable to DC180 and DC2112), standard on all


116

General

Information

CM

100C

M 200

CM

300F

ootnotes

CONDUIT BOX LOCATIONF1 520 $292 $292 $292 $292 $396 $438 $438 RGG 15F2 521 $292 $292 $292 $292 $396 $438 $438 RGG 15F3 (Top) 522 $292 $292 $292 $292 $396 $438 $438 RGG 15W5 (Wall Mount Vertical Shaft Up) 523 $292 $292 $292 $292 $396 $438 $438 RGG 15W6 (Wall Mount Vertical Shaft Down) 524 $292 $292 $292 $292 $396 $438 $438 RGG 15W7 (Wall Mount Vertical Shaft Down) 525 $292 $292 $292 $292 $396 $438 $438 RGG 15W8 (Wall Mount Vertical Shaft Up) 526 $292 $292 $292 $292 $396 $438 $438 RGG 15

COVERS (DPG-FV)Mod Est. LeadCode C180-C210 C250 C280 C320 C360 C400 C440 Time(days)

Vertical Mount Drip Covers* 527 $65 $93 $141 $219 $380 $528 $528 RGG 10Splashproof Covers** 528 $331 $422 $422 $422 $422 $633 $633 RGG 10

ENCLOSURE MODIFICATION

Mod Est. LeadEnclosure Modification Code C180-C210 C250 C280 C320 C360 C400 C440 Time(days)Separately Ventilated 535 ($531) ($759) ($1,050) ($1,318) ($1,444) ($1,734) ($2,119) RGG 10

Mod Est. LeadEnclosure Modification Code C180-C210 C250 C280 C320 C360 C400 C440 Time(days)

537 $281 $448 $604 $885 $1,469 $1,927 $1,927 RGG 20

538 $563 $688 $927 $1,151 $1,906 $2,229 $2,229 RGG 20

List Price

Location

Severe Duty Features (IP54) - The Allen-Bradley Severe Duty motor is designed for operation in damp locations where the motor will be subjected to corrosive conditions. Typical applications are paper, chemical, petroleum, fertilizer and plastics industries. Severe Dutymotors are provided in totally enclosed non-ventilated, totally enclosed fan-cooled and totally enclosed air-over construction.

Motors located in damp, moist environments must have space heaters to protect against condensation when the motor is not operating.

Location

* Special bracket louvers designed to insure drip-proof protection for vertically operated foot or flange mounted motors.

** For dripproof machines to meet NEMA MG1 - 1.25.2 requirements for splashproof enclosures. Provides protection against liquid drops or solid particles from entering the motor at any angle not greater than 100 degrees downward from the vertical.

Separately Ventilated - For applications where ventilated air is piped into the machine from an external source, basic DPG-FV enclosures may be separately ventilated at 3, 6, 9 and 12 o’clock for the below list price deductions. The inlet pipe can be fastened to one end bracket, and, if required and specified, an outlet pipe can be fastened to the other end bracket. Price does not include blower or pipe. Locations of air entry and air exhaust, if used, should be specified on order. Motors must not be operated without the separate air supply. Refer to Application Data Section for separate ventilating air requirements. (To insure adequate protection of a separately ventilated motor against loss of cooling air, an overtemperature device for interlocking with the controller overload protection circuit is recommended and should be added as standard practice. An air pressure differential switch is also recommended.) See pricing deduction chart below.

Severe Duty Features with Severe Duty Encoder option**

* Heavy gauge, large rectangular metal box. Standard on C400 and C440 frames.

NOTES REGARDING SEVERE DUTY MOTOR CONSTRUCTION:

**With an encoder not suitable for mill and chemical duty. To avoid exposed aluminum, MS connector is replaced with terminal block, mounted in auxiliary conduit box; encoder enclosed in sealed housing. Note: Price does not include encoder. Price does include adders for Auxiliary Conduit Box & Terminal Block for encoder leads.

*Without encoder option, or when encoder is inherently suitable for mill and chemical duty. (See Feedback Devices.)

Motors operating in dirty areas with fine abrasive dust such as taconite surrounding the motor should have dustproof/taconite features added in addition to this modification.

List PriceLocation

Severe Duty Features without Severe Duty Encoder option*

List Price


117

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

FEEDBACK DEVICES -Mounted To Stock Motors (Price Includes Mounting)

Power VDCMax Op Temp.

MaxRPM Output




MaxRPM Output







MaxRPM Output




5-15v 80 C 6000 Single 20

5-15v 80 C 6000 Single 20

RD-120-1 is a magneto-resistive encoder. It is designed to fit the front end cavity of the CM205 DC motor. It adds only 1.8 inches to the overall motor length. It is uni-direction for single direction motor operation.

RD-120-2 is a magneto-resistive encoder. It is designed to fit the front end cavity of the CM205 DC motor. It adds only 1.8 inches to the overall motor length. It is bi-direction for reversing direction motor operation.




Lakeshore SL56* - A Magnetoresistive Encoder suitable for Mill Duty applications. Enclosure allows for heavy machine vibration andaccidental impacts. Comes standard with 10 Pin Epic Style Industrial Connector.



Lakeshore RL67 - A Magnetoresistive Encoder suitable for Mill Duty applications. Enclosure allows for heavy machine vibration andaccidental impacts. The RL67 adds only 1.5 inches to overall motor length. Comes standard with 10 Pin Epic Style Industrial Connector.


BEARINGLESS ENCODERS - Mounts directly to the motor stub shaft without bearings or couplings. The Pulse Wheel of this type of encoder mounts directly to the motor stub shaft, which is then encased by the bracket of the encoder.


US List Price for DPFV,TEBC,TEN


609 1024 $9,073 608 512 $9,073 607 1024 $6,771

Avtron M485* - A Magnetoresistive Encoder suitable for Severe Duty applications. Enclosure is sealed against Dust & Water ingress.Comes standard with a 10 Pin Industrial Connector.

606 512 $6,771

603 2048 $3,958 602 1024 $3,958 601 2048 $3,484

Dynapar H56*- A direct replacement for the RD62 for mill duty applications. The H56 is a Photoelectric Encoder suitable Severe DutyApplications. Enclosure meets IP66. All Dynapar encoders are CE labeled.

600 1024 $3,484

585 2048 $1,927

Allen Bradley 845H - A Photoelectric Encoder suitable for Industrial applications. Enclosure meets IP66.584 1024 $1,927

581 2048 $1,354

Dynapar H20 - A Photoelectric Encoder suitable for Industrial Motion applications. Enclosure meets IP66. All Dynapar encoders areCE labeled.

580 1024 $1,354

COUPLED ENCODERS - Mounts to motor with the use of a stub shaft, flexible shaft coupling & flange adapter (flower pot). Standard Output is two channels (A & B), quadrature. All coupled encoders additions are performed at RGG.


US List Price for DPFV

558 2048 $1,146

BEI HS-35 - A Photoelectric Encoder suitable for applications involving Robotics, Oil Service & Web Process Control. Enclosure meets IP65. Comes standard with a 10 Pin Mating MS Connector.

557 1024 $1,146

HOLLOWSHAFT ENCODERS - Mount on motor stub shaft with no coupling required. A tether-arm mounts to the motor end bracket toprevent rotation of the encoder stator, and also to protect against shaft currents. Standard output is two channels (A & B), quadraturewith complementary outputs.


US List Price for DPFV


118

General

Information

CM

100C

M 200

CM

300F

ootnotes

INSULATION SYSTEMMod Est. Lead

Insulation Code C180-C210 C250 C280 C320 C360 C400 C440 Time(days)Tropical Protection 658 $186 $311 $480 $823 $1,111 $1,399 $2,302 RGG 20

SHAFT SEALSMod Est. Lead

Shaft Seal Code C180-C210 C250 C280 C320 C360 C400 C440 Time(days)Lip Seal* 674 RGG 10

SPACE HEATERS

Mod Est. LeadCode C180-C210 C250 C280 C320 C360 C400 C440 Time(days)

Space Heater - 120v 1ı- 677 RGG 15Space Heater - 230v 1ı- 678 RGG 15Space Heater - 460v 1ı- 679 RGG 15Space Heater Aux. C/B* 680 RGG 15

TERMINAL BLOCKS


Main Terminal Block 683 $292 $365 $479 $635 $781 $1,031 $1,031 RGG 15Accessory Terminal Block* 684 RGG 15

TESTS


687 RGG 10

689 $1,250 $1,563 $1,667 $1,875 $2,188 $3,333 $4,688 RGG 15

*Provides complete performance test per IEEE 113 as modified by Rockwell Automation for operation on inverter.

Certified Routine Test Report - Unwitnessed

$104

Certified Complete Test Report* - Unwitnessed

$104

*Provides terminal block in auxiliary conduit box for connection of pulse tachometer or digital encoder. Includes conduit box.

Tests - As standard practice, every CM203 motor is full load check tested, and receives a Routine Test per IEEE 113 as modified by Rockwell Automation.

List PriceLocation

*Separate conduit box for space heater leads and accessories.

Provides terminal block in main conduit box for connection of CM205 motor power leads, instead of the standard leads with terminallugs. Thermostat leads will not be connected to the terminal block.

List PriceLocation

$303$303$303

$216 $393 $458

* This modification provides a lip seal on the drive end to protect the bearing when operated with oil splashing against the shaft.Typical application is on a horizontal motor mounted to a gear case where the stationary oil level is below the motor shaft. CAUTION: Seals operated dry for extended periods will be damaged. LIST PRICE IS BASED PER BEARING.

Space heaters mounted inside the motor. Recommended to prevent condensation of moisture for motors remaining unenergized for long periods of time. Standard heater is single phase, 50/60 Hz. Leads are terminated in motor conduit boxes.

List PriceLocation

List PriceLocation

$141 $219

List PriceLocation

Note: Standard CM203 motors utilize an advanced insulation system that provides excellent protection against fungus and high humidity as found in tropical climates. The standard motor is suitable for operation in tropical climates without additional treatment. For additional protection, especially during shipment and prolonged storage, this modification provides a fungicidal air dry varnishtreatment per MIL-V-173C (Type I Treatment) applied over all motor windings. Motors applied in highly corrosive, moist and dirt-ladenenvironments should have an enclosure with Severe Duty features to limit the entrance of contaminants into the motor.


119

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


BasesFrame Dimension Discription AB Model AB List

Sheets Number PriceDC1810ATZ 609987-501 Standard Duty CMKIT-42384-26D $263DC1811ATZ 609987-501 Heavy Duty CMKIT-42384-26BE $315C1811ATZ 609987-1 Heavy Duty CMKIT-42384-26BE $315C1812ATZ 609987-1 Heavy Duty CMKIT-42384-26BF $315

DC2112ATZ 609958-51 Heavy Duty CMKIT-42384-26BH $315C2113ATZ 609957-1 Heavy Duty CMKIT-419914-1A $315C2115ATZ 609957-1 Heavy Duty CMKIT-419914-1P $315C2512ATZ 609957-1 Heavy Duty CMKIT-419914-1B $368C2514ATZ 609957-1 Heavy Duty CMKIT-419914-1R $368C2515ATZ 609957-1 Heavy Duty CMKIT-419914-1S $368

UC2812ATZ 609957-1 Heavy Duty CMKIT-419914-1C $473UC2813ATZ 609957-1 Heavy Duty CMKIT-419914-1T $473UC2815ATZ 609957-1 Heavy Duty CMKIT-419914-1U $473UC3212ATZ 609977-1 Heavy Duty CMKIT-419914-1D $473UC3214ATZ 609977-1 Heavy Duty CMKIT-419914-1W $473UC3612ATZ 609977-1 Heavy Duty CMKIT-419914-1E $933UC3613ATZ 609977-1 Heavy Duty CMKIT-419914-1X $933


BlowersFrame Discription AB Model AB List

Number PriceC180ATZ, DC180ATZ Blower Kit Without Filter CMKIT-417077-51 $729

C210ATZ Blower Kit Without Filter CMKIT-419947-29 $968C250ATZ Blower Kit Without Filter CMKIT-419947-30 $1,108C280ATZ Blower Kit Without Filter CMKIT-419947-32 $1,248C320ATZ Blower Kit Without Filter CMKIT-419947-34 $1,388C3612ATZ Blower Kit Without Filter CMKIT-417077-74 $1,575C3613ATZ Blower Kit Without Filter CMKIT-417077-127 $1,575C400ATZ Blower Kit Without Filter CMKIT-417077-75 $2,100C440ATZ Blower Kit Without Filter CMKIT-417077-126 $4,783



120

General

Information

CM

100C

M 200

CM

300F

ootnotes


Filter KitFrame AB Model Discription AB List

Number PriceC180ATZ, DC180ATZ CMKIT-417077-57 Washable Wire Mesh Canister Type $403

C2113ATZ CMKIT-417077-58 Washable Wire Mesh Canister Type $403C2115ATZ CMKIT-417077-59 Washable Wire Mesh Canister Type $403C2512ATZ CMKIT-417077-58 Washable Wire Mesh Canister Type $403C2514ATZ CMKIT-417077-59 Washable Wire Mesh Canister Type $403C2515ATZ CMKIT-417077-59 Washable Wire Mesh Canister Type $403C2812ATZ CMKIT-417077-59 Washable Wire Mesh Canister Type $403C2813ATZ CMKIT-417077-65 Washable Wire Mesh Canister Type $467C2815ATZ CMKIT-417077-65 Washable Wire Mesh Canister Type $467C3210ATZ CMKIT-417077-59 Washable Wire Mesh Canister Type $403C3212ATZ CMKIT-417077-59 Washable Wire Mesh Canister Type $403C3214ATZ CMKIT-417077-65 Washable Wire Mesh Canister Type $467C3612ATZ CMKIT-417077-65 Washable Wire Mesh Canister Type $467C3613ATZ CMKIT-417077-102 Washable Wire Mesh Canister Type $777C400ATZ CMKIT-417077-102 Washable Wire Mesh Canister Type $777C440ATZ CMKIT-417077-124 Square Replaceable Polyester Type $910


Mounting Kits Only (Less Tachometer)Frame Enclosure Device AB Model AB List

Type Type Number PriceDC180, C180, DC2112 DPG, DPFV, TENV BC42,BC46,H56,RE210,RD62 800123-R&-S CMKIT-413336-2R $618

C210-C250 DPG, DPFV, TENV BC42,BC46,H56,RE210,RD62 800123-R&-S CMKIT-417708-22 $618C280-C400 DPG, DPFV, TENV BC42,BC46,H56,RE210,RD62 800123-R&-S CMKIT-417708-27 $618

C440 DPG, DPFV, TENV BC42,BC46,H56,RE210,RD62 800123-R&-S CMKIT-417708-155 $618C180 TEFC BC42,BC46,H56,RE210,RD62 800123-R&-S CMKIT-417709-21 $1,237C210 TEFC BC42,BC46,H56,RE210,RD62 800123-R&-S CMKIT-417709-58 $1,237C250 TEFC BC42,BC46,H56,RE210,RD62 800123-R&-S CMKIT-417709-59 $1,237C280 TEFC BC42,BC46,H56,RE210,RD62 800123-R&-S CMKIT-417709-60 $1,237C320 TEFC BC42,BC46,H56,RE210,RD62 800123-R&-S CMKIT-417709-61 $1,237

DC180, C180, DC2112 DPG, DPFV, TENV 5PY, RPY444 CMKIT-413336-1R $618C210-C250 DPG, DPFV, TENV 5PY, RPY444 CMKIT-417708-21 $618C280-C400 DPG, DPFV, TENV 5PY, RPY444 CMKIT-417708-26 $618

C440 DPG, DPFV, TENV 5PY, RPY444 CMKIT-417708-156 $618C180 TEFC 5PY, RPY444 CMKIT-417709-17 $1,237C210 TEFC 5PY, RPY444 CMKIT-417709-65 $1,237C250 TEFC 5PY, RPY444 CMKIT-417709-66 $1,237C280 TEFC 5PY, RPY444 CMKIT-417709-67 $1,237C320 TEFC 5PY, RPY444 CMKIT-417709-68 $1,237

DC180, C180, DC2112 DPG, DPFV, TENV RL67 CMKIT-417708-40 $117C210 - C250 DPG, DPFV, TENV RL67 CMKIT-417708-41 $117C280 - C400 DPG, DPFV, TENV RL67 CMKIT-417708-42 $117

C440 DPG, DPFV, TENV RL67 CMKIT-417708-157 $146Discount Schedule 16


121

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


EncodersFrame Enclosure Device Output/PPR AB Model AB List

Type Type Number PriceDC180, C180, DC2112 DPG, DPFV RD120-1 1 x 120 ppr CMKIT-417708-30 $1,400

C210-C250 DPG, DPFV, TENV RD120-1 1 x 120 ppr CMKIT-417708-32 $1,400C280-C400 DPG, DPFV, TENV RD120-1 1 x 120 ppr CMKIT-417708-33 $1,400

C440 DPG, DPFV, TENV RD120-1 1 x 120 ppr CMKIT-417708-153 $1,400DC180, C180, DC2112 DPG, DPFV RD120-2 2 x 120 ppr CMKIT-417708-34 $1,721

C210-C250 DPG, DPFV, TENV RD120-2 2 x 120 ppr CMKIT-417708-36 $1,721C280-C400 DPG, DPFV, TENV RD120-2 2 x 120 ppr CMKIT-417708-37 $1,721

C440 DPG, DPFV, TENV RD120-2 2 x 120 ppr CMKIT-417708-154 $1,721DC180, C180, DC2112 DPG, DPFV, TENV H20 1024 ppr CMKIT-417708-133 $1,867

C210-C250 DPG, DPFV, TENV H20 1024 ppr CMKIT-417708-134 $1,867C280-C400 DPG, DPFV, TENV H20 1024 ppr CMKIT-417708-135 $1,867

C440 DPG, DPFV, TENV H20 1024 ppr CMKIT-417708-151 $1,867DC180, C180, DC2112 DPG, DPFV, TENV RL67 1024z ppr CMKIT-417708-126 $2,450

C210-C250 DPG, DPFV, TENV RL67 1024z ppr CMKIT-417708-136 $2,450C280-C400 DPG, DPFV, TENV RL67 1024z ppr CMKIT-417708-137 $2,450

C440 DPG, DPFV RL67 1024z ppr CMKIT-417708-138 $2,450DC180, C180, DC2112 DPG, DPFV, TENV 845HH 1024 ppr CMKIT-417708-105 $2,158

C210-C250 DPG, DPFV, TENV 845HH 1024 ppr CMKIT-417708-106 $2,158C280-C400 DPG, DPFV, TENV 845HH 1024 ppr CMKIT-417708-107 $2,158

C440 DPG, DPFV, TENV 845HH 1024 ppr CMKIT-417708-108 $2,158DC180, C180, DC2112 DPG, DPFV, TENV RE045 45 VAC/1000 RPM CMKIT-413327-W $1,867

C210-C250 DPG, DPFV, TENV RE045 45 VAC/1000 RPM CMKIT-417708-20 $1,867C280-C400 DPG, DPFV, TENV RE045 45 VAC/1000 RPM CMKIT-417708-25 $1,867

C440 DPG, DPFV, TENV RE045 45 VAC/1000 RPM CMKIT-417708-152 $1,867Discount Schedule 16

Tachometers Only (Less Mounting Hardware)Frame Enclosure Device Output/PPR AB Model AB List

Type Type Number Priceall all RPY444 50 VDC/1000 RPM CMKIT-417708-45 $1,020all all RPY444 100 VDC/1000 RPM CMKIT-417708-46 $1,020all all 5PY 50 VDC/1000 RPM CMKIT-R59E1050 $2,823all all 5PY 100 VDC/1000 RPM CMKIT-R59E1100 $2,823



122

General

Information

CM

100C

M 200

CM

300F

ootnotes


Architecture ClassIndustrial Environment SeriesCM206 Family - Totally Enclosed Small DC Motors

IntroductionAfter more than ninety years of DC motor design experience in the variable speed marketplace, Rockwell Automation continues its leadership position in DC motor technology with the CM206 Family - a small DC product line incorporating state-of-the-art design technology. This design results in a high quality industrial duty product with more customer value and benefits than ever before.

Standard Features• TEFC enclosure: Permanent magnet totally enclosed fan cooled designs have been optimized for control matched

performance. Cooler operating temperatures than TENV result in longer motor life and provide constant torque over a 20:1 speed range with a free wheeling diode.

• NEMA 56 C-Face mounting is standard on stock ratings.• Tach provisions easily obtained from stock kits with C-face fan covers.• Class F non-hygroscopic insulation system is standard for long motor life• New cartridge brush holders with brass inserts and stainless steel springs provide easy access to brushes and assure

constant pressure for long brush life. Disassembly is not required for brush inspection.• Oversize brushes and commutator assure long brush life.• Permanently lubricated double-shielded ball bearings prevent dirt entry and guard against grease loss.• Frames are heavy duty rolled steel, available with or without welded base.• Oversized top mounted conduit box with F1/F2 conduit connection and permanently marked leads simplify connec-

tions and installation (F1 lead outlet standard on explosion-proof).• U/L component recognition and CSA approval are standard (U/L file E 54825 and CSA file LR 40567).• Metric hardware and brushes.• Paint is blue-green high grade epoxy air dry enamel with non-toxic rust inhibitors.• 40°C Ambient• Class F Insulation.• IP53 Protection

Product OverviewCM205 SMALL DC MOTORSAvailable Features• Mounting: C-Face Foot Mounted, C-Face Footless• Enclosure Type: TEFC, TENV, FCXP, Washdown• Field Winding: Permanent Magnet, Wound• Horsepower Range: 1/7/98

Bearing System• Permanently lubricated double shielded• Double sealed (washdown)

Conduit Mounting• Top mounted (F1/F2)

Limited warranty• 18 months

CM206 Family - Totally Enclosed Small DC Motors

123

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


CM206 SMALL DC MOTORS

DescriptionCM206 Small DC motors are designed for reliability and long life in all variable speed applications.

Features• Permanent magnet TEFC designs have been optimized for control matched performance. Cooler operating

temperatures than TENV result in longer motor life and provide constant torque over a 20:1 speed range with a free wheeling diode

• Tach provisions easily obtained from stock kits with • C-face fan covers. Not available on explosion-proof.• Double-shielded ball bearings• Heavy duty rolled steel frames• Cartridge brush holders with brass inserts and stainless steel springs provide easy access to brushes and assure

constant pressure for long brush life. Disassembly is NOT required for brush inspection.• Oversized top mounted conduit box with F1/F2 conduit connection. F1 lead outlet standard on explosion-proof.

TEFC WASHDOWN EXPLOSION-PROOF


124

General

Information

CM

100C

M 200

CM

300F

ootnotes

Architecture Class, Industrial Environment Series

CM206 - Totally Enclosed Small DC Motors

C-Face Foot Mounted IP53Enclosure HP Speed- Frame Norm US List Catalog String Notes

Base Arm Field Stock Price CM205-TEFC 1/4 1750 90 PM SE56C Yes $335 FCF2517WXMCATEFC 1/4 1750 90 PM SE56C Yes $466 FCF2517WXMCB 90TEFC 1/4 1750 90 50/100 SG56HC Yes $666 FCF2517KXMCATEFC 1/4 1750 90 50/100 SG56HC Yes $743 FCF2517KXMCB 90TENV 1/4 1750 90 PM SE56C Yes $357 NVF2517WXMCA 8, 90TEFC 1/3 1750 90 PM SE56C Yes $354 FCF3317WXMCATEFC 1/3 1750 90 PM SE56C Yes $490 FCF3317WXMCB 90TEFC 1/3 1750 90 50/100 SG56HC Yes $676 FCF3317KXMCATEFC 1/3 1750 90 50/100 SG56HC Yes $753 FCF3317KXMCB 90TENV 1/3 1750 90 PM ME56C Yes $410 NVF3317WXMCA 8, 90TEFC 1/2 2500 90 PM SE56C Yes $354 FC0F525WXMCATEFC 1/2 2500 90 PM SE56C Yes $485 FC0F525WXMCB 90TEFC 1/2 1750 90 PM ME56C Yes $396 FC0F517WXMCATEFC 1/2 1750 90 PM ME56C Yes $536 FC0F517WXMCB 90TEFC 1/2 1750 180 PM LE56C Yes $396 FC0F517JXMCATEFC 1/2 1750 90 50/100 SG56HC Yes $700 FC0F517KXMCATEFC 1/2 1750 90 50/100 SG56HC Yes $777 FC0F517KXMCB 90TENV 1/2 1750 90 PM LE56C Yes $485 NV0F517WXMCA 8, 90TENV 1/2 1750 180 PM SF56HC Yes $1,013 NV0F517JXMCA 8, 90TEFC 3/4 1750 90 PM LE56C Yes $481 FCF7517WXMCATEFC 3/4 1750 90 PM LE56C Yes $635 FCF7517WXMCB 90TEFC 3/4 1750 180 PM SF56HC Yes $481 FCF7517JXMCATEFC 3/4 1750 90 50/100 MG56HC Yes $764 FCF7517KXMCATEFC 3/4 1750 90 50/100 MG56HC Yes $841 FCF7517KXMCB 90TENV 3/4 1750 90 PM SF56HC Yes $657 NVF7517WXMCA 8, 90TENV 3/4 1750 180 PM MF56HC Yes $1,058 NVF7517JXMCA 8, 90TEFC 1 1750 90 PM MF56HC Yes $587 FC00117WXMCATEFC 1 1750 90 PM MF56HC Yes $758 FC00117WXMCB 90TEFC 1 2500 180 PM SF56HC Yes $481 FC00125JXMCATEFC 1 2500 180 PM SF56HC Yes $758 FC00125JXMCB 90TEFC 1 1750 180 PM MF56HC Yes $587 FC00117JXMCATEFC 1 1750 180 PM MF56HC Yes $758 FC00117JXMCB 90TEFC 1 1750 180 100/200 LG56HC Yes $989 FC00117LXMCATEFC 1 1750 180 100/200 LG56HC Yes $1,066 FC00117LXMCB 90TENV 1 1750 90 PM LF56HCZ Yes $925 NV00117WXMCA 8, 90TENV 1 1750 180 PM LF56HCZ Yes $1,058 NV00117JXMCA 8, 90TEFC 1.5 1750 180 PM LF56HCZ Yes $1,113 FC1F517JXMCATEFC 1.5 1750 180 PM LF56HCZ Yes $1,370 FC1F517JXMCB 90TEFC 2 1750 180 PM LF56HCZ Yes $1,329 FC00217JXMCATEFC 2 1750 180 PM LF56HCZ Yes $1,621 FC00217JXMCB 90


Voltage


125

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

C-Face Footless IP53Enclosure HP Speed- Frame Norm US List Notes

Base Arm Field Stock PriceTEFC 1/4 1750 90 PM SE56C Yes $335 FCF2517WXMFATEFC 1/4 1750 90 PM SE56C Yes $461 FCF2517WXMFB 90TEFC 1/3 1750 90 PM SE56C Yes $354 FCF3317WXMFATEFC 1/3 1750 90 PM SE56C Yes $485 FCF3317WXMFB 90TEFC 1/2 1750 90 PM ME56C Yes $396 FC0F517WXMFATEFC 1/2 1750 90 PM ME56C Yes $531 FC0F517WXMFB 90TEFC 1/2 1750 180 PM LE56C Yes $396 FC0F517JXMFATEFC 1/2 1750 180 PM LE56C Yes $536 FC0F517JXMFB 90TEFC 1/2 2500 90 PM SE56C Yes $354 FC0F525WXMFATEFC 3/4 1750 90 PM LE56C Yes $481 FCF7517WXMFATEFC 3/4 1750 90 PM LE56C Yes $635 FCF7517WXMFB 90TEFC 3/4 1750 180 PM SF56C Yes $481 FCF7517JXMFATEFC 3/4 1750 180 PM SF56C Yes $660 FCF7517JXMFB 90TEFC 1 1750 90 PM MF56C Yes $587 FC00117WXMFATEFC 1 1750 90 PM MF56C Yes $753 FC00117WXMFB 90TEFC 1 1750 180 PM MF56C Yes $587 FC00117JXMFATEFC 1 2500 180 PM SF56C Yes $481 FC00125JXMFATEFC 1.5 1750 180 PM LF56CZ Yes $1,113 FC1F517JXMFATEFC 2 1750 180 PM LF56CZ Yes $1,329 FC00217JXMFA


Voltage


126

General

Information

CM

100C

M 200

CM

300F

ootnotes



Lead Time



BRAKES:Mount double c-face DODGE DBSS brake kit to Drive End of C-Face motor

706 3 ft. lb. 56C ALL 385$707 6 ft. lb. 56C ALL 427$708 10 ft. lb. 56C ALL 500$709 15 ft. lb. 56C ALL 583$

FEEDBACK DEVICE:Mounting of stock tachometer/encoder kits. Price includes all material and labor to mounton Opposite Drive End of motor.

733 RE007 tachometer ALL ALL 771$734 RE020 tachometer ALL ALL 771$735 M45E1000 (replaces RE045) tachometer ALL ALL 771$736 RPY444 (functional equivalent of 5PY) ALL ALL 1,583$737 BEI HS35 encoder, 5-15 vdc supply, Single output, 1024 ppr w/ marker pulse ALL TEFC 1,563$

INSULATION: Tropical protection764 Addition of anti-fungus treatment to windings. ALL ALL 63$

SEALS: Addition of shaft seal.777 V-ring rubber slinger on drive end ALL ALL 31$



Changes to an Order


127

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


CM300 Family

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Sine Wave ClassGeneral Purpose SeriesCM301 Family - Enclosed EE Rolled Steel AC Motors




Service Factor: 1.15 Temp. Rise: Class B Warranty (From Date Of Manufacture /



(24 / 12)




Conduit Box: F1 location. Diagonally split, rotatable in 90 degree incrementsBearing Type: Permanently lubricated, double shielded ball bearingsBearing Protection: Shaft slinger on drive endShaft Material: High strength carbon steelNameplate Material: AluminumDrain Type & Location: Weep holes on both end shields


128

General

Information

CM

100C

M 200

CM

300F

ootnotes

Sine Wave Class, General Purpose SeriesCM301 - Enclosed EE Rolled Steel AC Motors

Foot MountedEnclosure HP Synch Voltage Efficiency Inverter Norm. Frame Catalog String Notes US List

RPM Class Torque/Spd Stock CM301- PriceTEFC 1.5 1200 230/460 EE na Yes 182T FC1F512AEXHA 9 $407TEFC 2 1200 230/460 EE na Yes 184T FC00212AEXHA 9 $464TEFC 3600 230/460 EE na Yes 182T FC00336AEXHA 9 $403TEFC 1800 230/460 EE na Yes 182T FC00318AEXHA 9 $329TEFC 1200 230/460 EE na Yes 213T FC00312AEXHA 9 $543TEFC 3600 230/460 EE na Yes 184T FC00536AEXHA 9 $494TEFC 1800 230/460 EE na Yes 184T FC00518AEXHA 9 $398TEFC 1200 230/460 EE na Yes 215T FC00512AEXHA 9 $821TEFC 3600 230/460 EE na Yes 213T FC7F536AEXHA 9 $631TEFC 1800 230/460 EE na Yes 213T FC7F518AEXHA 9 $528TEFC 1200 230/460 EE na Yes 254T FC7F512AEXHA 9 $1,088TEFC 3600 230/460 EE na Yes 215T FC01036AEXHA 9 $762TEFC 1800 230/460 EE na Yes 215T FC01018AEXHA 9 $601TEFC 1200 230/460 EE na Yes 256T FC01012AEXHA 9 $1,370TEFC 3600 230/460 EE na Yes 254T FC01536AEXHA 9 $1,046TEFC 1800 230/460 EE na Yes 254T FC01518AEXHA 9 $939TEFC 1200 230/460 EE na Yes 284T FC01512AEXHA 9 $1,686TEFC 3600 230/460 EE na Yes 256T FC02036AEXHA 9 $1,292TEFC 1800 230/460 EE na Yes 256T FC02018AEXHA 9 $1,152TEFC 1200 230/460 EE na Yes 286T FC02012AEXHA 9 $2,097TEFC 3600 230/460 EE na Yes 284TS FC02536AEXHA 9,39 $1,488TEFC 1800 230/460 EE na Yes 284T FC02518AEXHA 9 $1,419TEFC 3600 230/460 EE na Yes 286TS FC03036AEXHA 9,39 $1,780TEFC 1800 230/460 EE na Yes 286T FC03018AEXHA 9 $1,686

Discount Schedule 16 e CC049A

C-Face Foot Mounted Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Notes US List

RPM Class Torque/Spd Stock PriceTEFC 1.5 1200 230/460 EE na Yes 182TCY FC1F512AEXCA 9 $482TEFC 2 1200 230/460 EE na Yes 184TCY FC00212AEXCA 9 $539TEFC 3600 230/460 EE na Yes 182TCY FC00336AEXCA 9 $478TEFC 1800 230/460 EE na Yes 182TCY FC00318AEXCA 9 $404TEFC 1200 230/460 EE na Yes 213TCY FC00312AEXCA 9 $618TEFC 3600 230/460 EE na Yes 184TCY FC00536AEXCA 9 $569TEFC 1800 230/460 EE na Yes 184TCY FC00518AEXCA 9 $474TEFC 1200 230/460 EE na Yes 215TCY FC00512AEXCA 9 $896TEFC 3600 230/460 EE na Yes 213TCY FC7F536AEXCA 9 $707TEFC 1800 230/460 EE na Yes 213TCY FC7F518AEXCA 9 $603TEFC 1200 230/460 EE na Yes 254TCY FC7F512AEXCA 9 $1,187TEFC 3600 230/460 EE na Yes 215TCY FC01036AEXCA 9 $837TEFC 1800 230/460 EE na Yes 215TCY FC01018AEXCA 9 $677TEFC 1200 230/460 EE na Yes 256TCY FC01012AEXCA 9 $1,469TEFC 3600 230/460 EE na Yes 254TCY FC01536AEXCA 9 $1,144TEFC 1800 230/460 EE na Yes 254TCY FC01518AEXCA 9 $1,037TEFC 1200 230/460 EE na Yes 284TC FC01512AEXCA 9 $1,822TEFC 3600 230/460 EE na Yes 256TCY FC02036AEXCA 9 $1,391TEFC 1800 230/460 EE na Yes 256TCY FC02018AEXCA 9 $1,251TEFC 1200 230/460 EE na Yes 286TC FC02012AEXCA 9 $2,233TEFC 3600 230/460 EE na Yes 284TSC FC02536AEXCA 9,39 $1,625TEFC 1800 230/460 EE na Yes 284TC FC02518AEXCA 9 $1,555TEFC 3600 230/460 EE na Yes 286TSC FC03036AEXCA 9,39 $1,916TEFC 1800 230/460 EE na Yes 286TC FC03018AEXCA 9 $1,822

Discount Schedule 16 e CC049A

3

5

7.5

10

15

20

25

30

3

5

7.5

10

15

20

25

30


129

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

C-Face FootlessEnclosure HP Synch Voltage Efficiency Inverter Norm. Frame Notes US List

RPM Class Torque/Spd Stock PriceTEFC 1.5 1200 230/460 EE na Yes 182TC FC1F512AEXFA 9 $500TEFC 2 1200 230/460 EE na Yes 184TC FC00212AEXFA 9 $557TEFC 3600 230/460 EE na Yes 182TC FC00336AEXFA 9 $496TEFC 1800 230/460 EE na Yes 182TC FC00318AEXFA 9 $422TEFC 1200 230/460 EE na Yes 213TC FC00312AEXFA 9 $636TEFC 3600 230/460 EE na Yes 184TC FC00536AEXFA 9 $587TEFC 1800 230/460 EE na Yes 184TC FC00518AEXFA 9 $491TEFC 1200 230/460 EE na Yes 215TC FC00512AEXFA 9 $914TEFC 3600 230/460 EE na Yes 213TC FC7F536AEXFA 9 $724TEFC 1800 230/460 EE na Yes 213TC FC7F518AEXFA 9 $621TEFC 1200 230/460 EE na Yes 254TC FC7F512AEXFA 9 $1,229TEFC 3600 230/460 EE na Yes 215TC FC01036AEXFA 9 $855TEFC 1800 230/460 EE na Yes 215TC FC01018AEXFA 9 $694TEFC 1200 230/460 EE na Yes 256TC FC01012AEXFA 9 $1,511TEFC 3600 230/460 EE na Yes 254TC FC01536AEXFA 9 $1,187TEFC 1800 230/460 EE na Yes 254TC FC01518AEXFA 9 $1,080TEFC 1200 230/460 EE na Yes 284TC FC01512AEXFA 9 $1,886TEFC 3600 230/460 EE na Yes 256TCY FC02036AEXFA 9 $1,433TEFC 1800 230/460 EE na Yes 256TCY FC02018AEXFA 9 $1,293TEFC 1200 230/460 EE na Yes 286TC FC02012AEXFA 9 $2,297TEFC 3600 230/460 EE na Yes 284TSC FC02536AEXFA 9,39 $1,688TEFC 1800 230/460 EE na Yes 284TC FC02518AEXFA 9 $1,619TEFC 3600 230/460 EE na Yes 286TSC FC03036AEXFA 9,39 $1,980TEFC 1800 230/460 EE na Yes 286TC FC03018AEXFA 9 $1,886


3

5

7.5

10

15

20

25

30


130

General

Information

CM

100C

M 200

CM

300F

ootnotes





CONNECTIONS: Final connect dual to single voltage.107 High Voltage Connection All $162108 Low Voltage Connection All $162

DRIP COVERS: Mounting of stock canopy kits (price includes kit).116 Install canopy kit to allow for vertical shaft down operation. 180-210 $216

Note: This modification does not provide vertical lifting provisions. 250-280 $270LEAD TERMINALS: Addition of lead terminals to wires in conduit box.

135 Compression type (Burndy, etc.) lead lugs All $270MOUNTING: Move conduit box to allow different mounting configurations.









159 Mount a set of qty (3) normally closed thermostats All $424




131

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Sine Wave ClassGeneral Purpose SeriesCM302 Family - Enclosed EE Cast Iron AC Motors






Application InformationCast Iron general purpose CM302 AC motors are an ideal choice for applications such as: Fans, Blowers, Compressors, Pumps and Conveyors.

(24 / 12)


180T - 360T FramesMaterials: Cast iron frame and end shields, fabricated steel conduit box

and fan cover (180T - 210T frames), Cast Iron frame, end shields, conduit box and fan cover (320T - 360T frames).

Conduit Box: F1, Diagonally split, rotatable in 90 degree incrementsBearing Type: BallBearing Protection: SlingersShaft Material: High strength carbon steelNameplate Material: AluminumDrain Type & Location: Weep holes both ends


132

General

Information

CM

100C

M 200

CM

300F

ootnotes

Sine Wave Class, General Purpose SeriesCM302 - Enclosed EE Cast Iron AC Motors


RPM Class Torque/Spd Stock CM302- PriceTEFC 3 3600 230/460 EE na Yes 182T FC00336AEXHA 9 $436TEFC 3 3600 575 EE na Yes 182T FC00336CEXHA 9 $436TEFC 3 1800 230/460 EE na Yes 182T FC00318AEXHA 9 $403TEFC 3 1800 575 EE na Yes 182T FC00318CEXHA 9 $403TEFC 3 1200 230/460 EE na Yes 213T FC00312AEXHA 9 $587TEFC 3 1200 575 EE na Yes 213T FC00312CEXHA 9 $587TEFC 5 3600 230/460 EE na Yes 184T FC00536AEXHA 9 $533TEFC 5 3600 575 EE na Yes 184T FC00536CEXHA 9 $533TEFC 5 1800 230/460 EE na Yes 184T FC00518AEXHA 9 $487TEFC 5 1800 575 EE na Yes 184T FC00518CEXHA 9 $487TEFC 5 1200 230/460 EE na Yes 215T FC00512AEXHA 9 $887TEFC 5 1200 575 EE na Yes 215T FC00512CEXHA 9 $887TEFC 7.5 3600 230/460 EE na Yes 213T FC7F536AEXHA 9 $682TEFC 7.5 3600 575 EE na Yes 213T FC7F536CEXHA 9 $682TEFC 7.5 1800 230/460 EE na Yes 213T FC7F518AEXHA 9 $647TEFC 7.5 1800 575 EE na Yes 213T FC7F518CEXHA 9 $647TEFC 7.5 1200 230/460 EE na Yes 254T FC7F512AEXHA 9 $1,280TEFC 7.5 1200 575 EE na Yes 254T FC7F512CEXHA 9 $1,280TEFC 10 3600 230/460 EE na Yes 215T FC01036AEXHA 9 $822TEFC 10 3600 575 EE na Yes 215T FC01036CEXHA 9 $822TEFC 10 1800 230/460 EE na Yes 215T FC01018AEXHA 9 $737TEFC 10 1800 575 EE na Yes 215T FC01018CEXHA 9 $737TEFC 10 1200 230/460 EE na Yes 256T FC01012AEXHA 9 $1,612TEFC 10 1200 575 EE na Yes 256T FC01012CEXHA 9 $1,612TEFC 15 3600 230/460 EE na Yes 254T FC01536AEXHA 9 $1,231TEFC 15 3600 575 EE na Yes 254T FC01536CEXHA 9 $1,231TEFC 15 1800 230/460 EE na Yes 254T FC01518AEXHA 9 $1,105TEFC 15 1800 575 EE na Yes 254T FC01518CEXHA 9 $1,105TEFC 15 1200 230/460 EE na Yes 284T FC01512AEXHA 9 $1,983TEFC 15 1200 575 EE na Yes 284T FC01512CEXHA 9 $1,983TEFC 20 3600 230/460 EE na Yes 256T FC02036AEXHA 9 $1,520TEFC 20 3600 575 EE na Yes 256T FC02036CEXHA 9 $1,520TEFC 20 1800 230/460 EE na Yes 256T FC02018AEXHA 9 $1,356TEFC 20 1800 575 EE na Yes 256T FC02018CEXHA 9 $1,356TEFC 20 1200 230/460 EE na Yes 286T FC02012AEXHA 9 $2,465TEFC 20 1200 575 EE na Yes 286T FC02012CEXHA 9 $2,465TEFC 25 3600 230/460 EE na Yes 284TS FC02536AEXHA 9 $1,751TEFC 25 3600 575 EE na Yes 284TS FC02536CEXHA 9 $1,751TEFC 25 1800 230/460 EE na Yes 284T FC02518AEXHA 9 $1,670TEFC 25 1800 575 EE na Yes 284T FC02518CEXHA 9 $1,670TEFC 25 1200 230/460 EE na Yes 324T FC02512AEXHA 9 $2,934TEFC 25 1200 575 EE na Yes 324T FC02512CEXHA 9 $2,934TEFC 30 3600 230/460 EE na Yes 286TS FC03036AEXHA 9 $2,094TEFC 30 3600 575 EE na Yes 286TS FC03036CEXHA 9 $2,094TEFC 30 1800 230/460 EE na Yes 286T FC03018AEXHA 9 $1,983TEFC 30 1800 575 EE na Yes 286T FC03018CEXHA 9 $1,983TEFC 30 1200 230/460 EE na Yes 326T FC03012AEXHA 9 $3,382TEFC 30 1200 575 EE na Yes 326T FC03012CEXHA 9 $3,382TEFC 40 3600 230/460 EE na Yes 324TS FC04036AEXHA 9 $2,618TEFC 40 3600 575 EE na Yes 324TS FC04036CEXHA 9 $2,618TEFC 40 1800 230/460 EE na Yes 324T FC04018AEXHA 9 $2,593TEFC 40 1800 575 EE na Yes 324T FC04018CEXHA 9 $2,593TEFC 40 1200 230/460 EE na Yes 364T FC04012AEXHA 9 $4,549TEFC 40 1200 575 EE na Yes 364T FC04012CEXHA 9 $4,549


133

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 50 3600 230/460 EE na Yes 326TS FC05036AEXHA 9 $3,414TEFC 50 3600 575 EE na Yes 326TS FC05036CEXHA 9 $3,414TEFC 50 1800 230/460 EE na Yes 326T FC05018AEXHA 9 $2,723TEFC 50 1800 575 EE na Yes 326T FC05018CEXHA 9 $2,723TEFC 50 1200 575 EE na Yes 365T FC05012CEXHA 9 $5,353


C-Face Foot Mounted IP54Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Notes US List

RPM Class Torque/Spd Stock PriceTEFC 3 3600 230/460 EE na Yes 182TCY FC00336AEXCA 9 $505TEFC 3 1800 230/460 EE na Yes 182TCY FC00318AEXCA 9 $472TEFC 3 1200 230/460 EE na Yes 213TCY FC00312AEXCA 9 $657TEFC 5 3600 230/460 EE na Yes 184TCY FC00536AEXCA 9 $602TEFC 5 1800 230/460 EE na Yes 184TCY FC00518AEXCA 9 $555TEFC 5 1200 230/460 EE na Yes 215TCY FC00512AEXCA 9 $956TEFC 7.5 3600 230/460 EE na Yes 213TCY FC7F536AEXCA 9 $752TEFC 7.5 1800 230/460 EE na Yes 213TCY FC7F518AEXCA 9 $716TEFC 7.5 1200 230/460 EE na Yes 254TCY FC7F512AEXCA 9,47 $1,370TEFC 10 3600 230/460 EE na Yes 215TCY FC01036AEXCA 9 $891TEFC 10 1800 230/460 EE na Yes 215TCY FC01018AEXCA 9 $805TEFC 10 1200 230/460 EE na Yes 256TCY FC01012AEXCA 9 $1,703TEFC 15 3600 230/460 EE na Yes 254TCY FC01536AEXCA 9,47 $1,330TEFC 15 1800 230/460 EE na Yes 254TCY FC01518AEXCA 9,47 $1,204TEFC 15 1200 230/460 EE na Yes 284TC FC01512AEXCA 9 $2,119TEFC 20 3600 230/460 EE na Yes 256TCY FC02036AEXCA 9,47 $1,619TEFC 20 1800 230/460 EE na Yes 256TCY FC02018AEXCA 9,47 $1,454TEFC 20 1200 230/460 EE na Yes 286TC FC02012AEXCA 9 $2,602TEFC 25 3600 230/460 EE na Yes 284TSC FC02536AEXCA 9 $1,888TEFC 25 1800 230/460 EE na Yes 284TC FC02518AEXCA 9 $1,806TEFC 30 3600 230/460 EE na Yes 286TSC FC03036AEXCA 9 $2,231TEFC 30 1800 230/460 EE na Yes 286TC FC03018AEXCA 9 $2,119



134

General

Information

CM

100C

M 200

CM

300F

ootnotes





CONNECTIONS: Final connect dual to single voltage.107 High Voltage Connection (price by frame size) 180-320 $162108 Low Voltage Connection (price by frame size) 360 $216














135

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Sine Wave ClassGeneral Purpose SeriesCM303 Family - Enclosed EE/PE/NP AC Motors



Frequency: 60 Hz Duty Cycle: Continuous EE = Energy Efficient motors that meet EPAct efficiency levels.Ambient: 40° C Insulation: Class F

Service Factor: 1.15 Temp. Rise: Class B PE = Premium Efficient motors that exceed EPAct efficiency levels


Application InformationDesigned for all general purpose industrial applications in a dusty, dirty, and/or humid environment. Enclosed motors reduce the exchange of air between the inside and the outside of the motor.


EE (24 / 12), PE (36 / 24), NP (36 / 24)Nameplate Agency Approvals:CE, CSA, UR

48 - 140T FramesMaterials: Steel frame, conduit box and fan shroud; cast aluminum end

shields.Conduit Box: Oversized, top mounted with F1 & F2 lead outletsBearing Type: Double shielded ball bearingsBearing Protection: Permanently lubricated with moisture resistant greaseShaft Material: High strength carbon steelNameplate Material: Adhesive MylarDrain Type & Location: Weep hole in both end shields

180T - 449T FramesMaterials: Cast iron frame & end shield; steel fan shroud and conduit box Conduit Box: F1 location, diagonally split, rotatable in 90 degree incrementsBearing Type: Permanently lubricated, double shielded ball bearings (180T -

360T frames); regreasable, open ball bearings with PLS (400T - 449T frames)

Bearing Protection: Shaft slinger on drive endShaft Material: High strength carbon steelNameplate Material: Stainless SteelDrain Type & Location: Weep holes in both end shields


136

General

Information

CM

100C

M 200

CM

300F

ootnotes

Sine Wave Class, General Purpose SeriesCM303 - Enclosed SE/EE/PE/NP AC Motors


RPM Class Torque/Spd Stock CM303- PriceTENV 0.17 1200 208-230/460 EE na Yes 48 NVF1712GEXHA 15 $303TENV 0.25 3600 208-230/460 EE na N 48 NVF2536GEXHA $222TENV 0.25 1800 208-230/460 EE na Yes 48 NVF2518GEXHA 15 $222TENV 0.25 1800 230/460 EE na N 56 NVF2518AEXHA $222TENV 0.25 1800 208-230/460 EE na Yes 56 NVF2518GEXHA $197TENV 0.25 1800 230/460 PE na N 56 NVF2518APXHA $386TENV 0.25 1200 230/460 EE na N 56 NVF2512AEXHA $382TENV 0.25 1200 230/460 PE na N 56 NVF2512APXHA $505TEFC 0.25 900 208-230/460 EE na N 56 FCF2509GEXHA $486TENV 0.33 3600 208-230/460 EE na Yes 48 NVF3336GEXHA 15 $222TENV 0.33 3600 230/460 EE na N 56 NVF3336AEXHA $229TENV 0.33 3600 230/460 PE na N 56 NVF3336APXHA $313TENV 0.33 1800 208-230/460 EE na Yes 48 NVF3318GEXHA 15 $241TENV 0.33 1800 230/460 EE na Yes 56 NVF3318AEXHA $285TEFC 0.33 1800 208-230/460 EE na Yes 56 FCF3318GEXHA $191TENV 0.33 1800 230/460 PE na Yes 56 NVF3318APXHA $403TENV 0.33 1200 230/460 EE na Yes 56 NVF3312AEXHA $377TENV 0.33 1200 230/460 PE na Yes 56 NVF3312APXHA $514TEFC 0.33 900 208-230/460 EE na N 56 FCF3309GEXHA $532TEFC 0.5 3600 208-230/460 EE na Yes 48 FC0F536GEXHA 15 $238TEFC 0.5 3600 208-230/460 EE na N 56 FC0F536GEXHA $265TEFC 0.5 3600 230/460 PE na Yes 56 FC0F536APXHA $335TEFC 0.5 1800 208-230/460 EE na Yes 56 FC0F518GEXHB 15 $254TEFC 0.5 1800 230/460 PE na Yes 56 FC0F518APXHA $422TEFC 0.5 1200 208-230/460 EE na Yes 56 FC0F512GEXHA 15 $352TEFC 0.5 1200 230/460 PE na Yes 56 FC0F512APXHA $566TEFC 0.5 900 208-230/460 EE na N 56 FC0F509GEXHA $568TEFC 0.75 3600 208-230/460 EE na Yes 56 FCF7536GEXHA $289TEFC 0.75 3600 230/460 PE na Yes 56 FCF7536APXHA $388TEFC 0.75 1800 208-230/460 EE na Yes 56 FCF7518GEXHB $268TEFC 0.75 1800 230/460 PE na Yes 56 FCF7518APXHA $462TEFC 0.75 1200 208-230/460 EE na Yes 56 FCF7512GEXHA $423TEFC 0.75 1200 230/460 EE na Yes 143T FCF7512AEXHA $423TEFC 0.75 1200 230/460 PE na Yes 143T FCF7512APXHA 50 $817TEFC 0.75 1200 230/460 PE na N 143T FCF7512APXHA $624TEFC 0.75 900 208-230/460 EE na N 56 FCF7509GEXHA $604TEFC 0.75 900 230/460 EE na Yes 145T FCF7509AEXHA $604TEFC 1 3600 208-230/460 EE na Yes 56 FC00136GEXHA $334TENV 1 3600 230/460 PE na Yes 56 NV00136APXHA $438TEFC 1 3600 230/460 NP na Yes 143T FC00136ANXHA 50 $617TEFC 1 3600 230/460 PE na N 143T FC00136APXHA $377TEFC 1 1800 208-230/460 EE na Yes 56 FC00118GEXHA $243TEFC 1 1800 230/460 EE na Yes 143T FC00118AEXHA $271TEFC 1 1800 230/460 PE na Yes 56 FC00118APXH5A $474TEFC 1 1800 230/460 NP na Yes 143T FC00118ANXHA 50 $639TEFC 1 1800 230/460 PE na Yes 143T FC00118APXH4A $494TEFC 1 1200 230/460 EE na N 56 FC00112AEXH5A $457TEFC 1 1200 230/460 EE na Yes 145T FC00112AEXH4A $457TEFC 1 1200 230/460 PE na N 56 FC00112APXH5A $627TEFC 1 1200 230/460 PE na Yes 145T FC00112APXH4A 50 $808TEFC 1 1200 230/460 NP na Yes 145T FC00112ANXHA $627


137

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 1.5 3600 230/460 EE na N 56 FC1F536AEXH5A $404TEFC 1.5 3600 230/460 EE na Yes 143T FC1F536AEXH4A $404TEFC 1.5 3600 230/460 PE na N 56 FC1F536APXH5A $532TEFC 1.5 3600 230/460 PE na Yes 143T FC1F536APXH4A 50 $710TEFC 1.5 3600 230/460 NP na N 145T FC1F536ANXHA $532TEFC 1.5 1800 230/460 EE na N 56 FC1F518AEXH5A $352TEFC 1.5 1800 208-230/460 EE na Yes 56 FC1F518GEXHA 2 $274TEFC 1.5 1800 230/460 EE na Yes 145T FC1F518AEXH4A $352TEFC 1.5 1800 230/460 PE na N 56 FC1F518APXHNA $521TEFC 1.5 1800 230/460 PE na Yes 145T FC1F518APXHYA 50 $687TEFC 1.5 1800 230/460 NP na Yes 145T FC1F518ANXHA $511TEFC 1.5 1200 230/460 EE na Yes 145T FC1F512AEXHNA $514TEFC 1.5 1200 230/460 EE na Yes 182T FC1F512AEXHYA 9 $557TEFC 1.5 1200 230/460 NP na Yes 182T FC1F512ANXHA 9 $645TEFC 2 3600 230/460 EE na Yes 56 FC00236AEXH5A $470TEFC 2 3600 230/460 EE na Yes 145T FC00236AEXH4A $470TEFC 2 3600 230/460 PE na N 56 FC00236APXHNA $621TEFC 2 3600 230/460 PE na Yes 145T FC00236APXHYA 50 $801TEFC 2 3600 230/460 NP na N 145T FC00236ANXHA $621TEFC 2 1800 230/460 EE na N 56 FC00218AEXHA $388TEFC 2 1800 208-230/460 EE na Yes 56 FC00218GEXHA 2 $296TEFC 2 1800 230/460 EE na Yes 145T FC00218AEXHB $388TEFC 2 1800 230/460 PE na N 56 FC00218APXHA $562TEFC 2 1800 230/460 PE na Yes 145T FC00218APXHA 50 $735TEFC 2 1800 230/460 NP na Yes 145T FC00218ANXHA $532TEFC 2 1200 230/460 EE na Yes 184T FC00212AEXHA 9 $501TEFC 2 1200 230/460 NP na Yes 184T FC00212ANXHA 9 $738TEFC 3 3600 208-230/460 EE na N 56 FC00336GEXHA $510TEFC 3 3600 230/460 EE na Yes 145T FC00336AEXHA $510TEFC 3 3600 230/460 NP na Yes 182T FC00336ANXHA 9 $630TEFC 3 1800 230/460 NP na N L182T FC00318ANXHA $582TEFC 3 1800 200/208 PE na Yes 182T FC00318HPXHA 75 $582TEFC 3 1200 230/460 NP na Yes 213T FC00312ANXHA 9 $863TEFC 3 900 460 PE na N L215T FC00309BPXHA $1,456TEFC 5 3600 230/460 NP na Yes 184T FC00536ANXHA 9 $770TEFC 5 1800 200/208 EE na Yes 184T FC00518HEXHA 75 $615TEFC 5 1800 230/460 NP na Yes 184T FC00518ANXHA 9 $704TEFC 5 1200 230/460 NP na Yes 215T FC00512ANXHA 9 $1,305TEFC 5 900 460 PE na N 254T FC00509BPXHA $1,785TEFC 7.5 3600 230/460 NP na Yes 213T FC7F536ANXHA $1,151TEFC 7.5 1800 230/460 PE na Yes 213T FC7F518APXHA $934TEFC 7.5 1800 230/460 NP na Yes 213T FC7F518ANXHA $1,027TEFC 7.5 1200 230/460 NP na Yes 254T FC7F512ANXHA 9 $1,729TEFC 7.5 900 460 PE na N 256T FC7F509BPXHA $3,177TEFC 10 3600 230/460 NP na Yes 215T FC01036ANXHA 9 $1,189TEFC 10 1800 230/460 NP na Yes 215T FC01018ANXHA 9 $1,063TEFC 10 1800 230/460 PE na Yes L215T FC01018APXHA $1,063TEFC 10 1200 230/460 NP na Yes 256T FC01012ANXHA 9 $2,178TEFC 10 900 460 PE na N 284T FC01009BPXHA $3,180TEFC 15 3600 230/460 NP na Yes 254T FC01536ANXHA $1,890TEFC 15 1800 230/460 PE na Yes 254T FC01518APXHA $1,466TEFC 15 1800 230/460 NP na Yes 254T FC01518ANXHA 9 $1,466TEFC 15 1200 230/460 NP na Yes 284T FC01512ANXHA 9 $2,754TEFC 15 900 460 PE na N 286T FC01509BPXHA $4,054TEFC 20 3600 230/460 NP na Yes 256T FC02036ANXHA $2,017TEFC 20 1800 230/460 PE na Yes 256T FC02018APXHA $1,797TEFC 20 1800 230/460 NP na Yes 256T FC02018ANXHA 9 $1,797TEFC 20 1200 230/460 NP na Yes 286T FC02012ANXHA 9 $3,507TEFC 20 900 460 PE na N 324T FC02009BPXHA $5,140


138

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 25 3600 230/460 NP na Yes 284TS FC02536ANXHA $2,552TEFC 25 1800 230/460 NP na Yes 284T FC02518ANXHA 9 $2,323TEFC 25 1800 230/460 PE na Yes 284T FC02518APXHA $2,323TEFC 25 1200 230/460 NP na N 324T FC02512ANXHA $3,966TEFC 25 900 460 PE na N 326T FC02509BPXHA $6,034TEFC 30 3600 230/460 NP na Yes 286TS FC03036ANXHA 9 $2,934TEFC 30 1800 230/460 NP na Yes 286T FC03018ANXHA 9 $2,757TEFC 30 1800 230/460 PE na Yes 286T FC03018APXHA $2,757TEFC 30 1200 230/460 NP na N 326T FC03012ANXHA $4,567TEFC 30 900 460 PE na N 364T FC03009BPXHA $6,903TEFC 40 3600 230/460 NP na N 324TS FC04036ANXHA $3,536TEFC 40 1800 230/460 NP na Yes 324T FC04018ANXHA $3,504TEFC 40 1200 230/460 NP na N 364T FC04012ANXHA $6,146TEFC 40 900 460 PE na N 365T FC04009BPXHA $8,482TEFC 50 3600 230/460 NP na N 326TS FC05036ANXHA $4,611TEFC 50 1800 230/460 NP na Yes 326T FC05018ANXHA $4,162TEFC 50 1200 230/460 NP na N 365T FC05012ANXHA $7,230TEFC 50 1200 230/460 EE na Yes 365T FC05012AEXHA 9 $5,353TEFC 50 900 460 PE na N 404T FC05009BPXHA $10,041TEFC 60 3600 230/460 NP na N 364TS FC06036ANXHA $6,269TEFC 60 3600 230/460 EE na Yes 364TS FC06036AEXHB $5,392TEFC 60 1800 230/460 NP na Yes 364T FC06018ANXHA $6,126TEFC 60 1800 230/460 EE na Yes 364T FC06018AEXHA $5,270TEFC 60 1200 230/460 NP na N 404T FC06012ANXHA $8,307TEFC 60 1200 230/460 EE na Yes 404T FC06012AEXHA $7,145TEFC 60 900 460 PE na N 405T FC06009BPXHA $11,594TEFC 75 3600 230/460 NP na N 365TS FC07536ANXHA $7,832TEFC 75 3600 230/460 EE na Yes 365TS FC07536AEXHB $6,736TEFC 75 1800 230/460 NP na N 365T FC07518ANXHA $7,555TEFC 75 1800 230/460 EE na Yes 365T FC07518AEXHA $5,951TEFC 75 1200 230/460 NP na N 405T FC07512ANXHA $9,323TEFC 75 1200 230/460 EE na Yes 405T FC07512AEXHB $8,017TEFC 75 900 460 PE na N 444T FC07509BPXHA $15,114TEFC 100 3600 230/460 NP na N 405TS FC10036ANXHA $10,115TEFC 100 3600 230/460 EE na Yes 405TS FC10036AEXHA 9 $8,699TEFC 100 1800 460 NP na Yes 405T FC10018BNXHA $9,268TEFC 100 1800 230/460 EE na Yes 405TS FC10018AEXHB $7,970TEFC 100 1200 230/460 NP na N 444T FC10012ANXHA $14,829TEFC 100 1200 230/460 EE na Yes 444T FC10012AEXHA 9 $10,687TEFC 125 3600 460 EE na Yes 444TS FC12536BEXHA $11,225TEFC 125 3600 460 NP na N 444TS FC12536BNXHA $13,051TEFC 125 1800 460 EE na Yes 444T FC12518BEXHTA $10,354TEFC 125 1800 460 NP na Yes 444T FC12518BNXHA $12,040TEFC 125 1800 460 EE na Yes 444TS FC12518BEXHSA $10,354TEFC 125 1200 460 EE na Yes 445T FC12512BEXHA $13,087TEFC 125 1200 460 NP na N 445T FC12512BNXHA $15,217TEFC 150 3600 460 EE na Yes 445TS FC15036BEXHA $13,706TEFC 150 3600 460 NP na N 445TS FC15036BNXHA $15,937TEFC 150 1800 460 EE na Yes 445T FC15018BEXHNA $12,216TEFC 150 1800 460 NP na Yes 445T FC15018BNXHA $14,204TEFC 150 1800 460 EE na Yes 445TS FC15018BEXHSA $12,216TEFC 150 1200 460 EE na Yes 445T FC15012BEXUA 5 $14,957TEFC 150 1200 460 EE na Yes 445TS FC15012BEXHB $14,957TEFC 150 1200 460 NP na N 445T FC15012BNXHA $17,395


139

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 200 3600 460 EE na Yes 445TS FC20036BEXHA 4 $17,628TEFC 200 3600 460 NP na N 445TS FC20036BNXHA $20,496TEFC 200 1800 460 EE na Yes 445T FC20018BEXUA 4,5 $15,037TEFC 200 1800 460 NP na Yes 447T FC20018BNXUA 5 $16,824TEFC 200 1800 460 EE na Yes 445TS FC20018BEXHA $15,591TEFC 200 1800 460 PE na N 447TS FC20018BPXHA $16,824TEFC 200 1200 460 EE na Yes 447T FC20012BEXUA 4,5 $17,618TEFC 200 1200 460 NP na N 449T FC20012BNXUA 5 $19,754TEFC 250 3600 460 EE na Yes 447TS FC25036BEXHA 4 $22,524TEFC 250 3600 460 NP na N 447TS FC25036BNXHA $25,455TEFC 250 1800 460 EE na Yes 447TS FC25018BEXHB 4 $17,914TEFC 250 1800 460 EE na Yes 447T FC25018BEXUA 4,5 $17,914TEFC 250 1800 460 NP na N 449T FC25018BNXUA 5 $20,097TEFC 250 1200 460 EE na Yes 449T FC25012BEXUA 4,5 $23,193TEFC 250 1200 460 NP na N 449T FC25012BNXUA 5 $26,234TEFC 300 3600 460 NP na N 449TS FC30036BNXHA $32,165TEFC 300 1800 460 EE na Yes 449TS FC30018BEXHA 4 $21,235TEFC 300 1800 460 NP na N 449T FC30018BNXUA 5 $23,959TEFC 350 3600 460 NP na N 449TS FC35036BNXHA $36,591TEFC 350 1800 460 NP na N 449T FC35018BNXUA 5 $28,286



RPM Class Torque/Spd Stock PriceTENV 0.25 3600 208-230/460 EE na N 56C NVF2536GEXCA $255TENV 0.25 1800 230/460 EE na Yes 56C NVF2518AEXCA 15 $284TENV 0.25 1200 230/460 EE na Yes 56C NVF2512AEXCA 15 $415TEFC 0.25 900 208-230/460 EE na Yes 56C FCF2509GEXCA $520TENV 0.33 3600 230/460 EE na Yes 56C NVF3336AEXCA 15 $262TENV 0.33 1800 230/460 EE na Yes 56C NVF3318AEXCA 15 $289TEFC 0.33 1800 208-230/460 EE na Yes 56C FCF3318GEXCA 2 $216TENV 0.33 1200 230/460 EE na Yes 56C NVF3312AEXCA 15 $415TEFC 0.33 900 208-230/460 EE na N 56C FCF3309GEXCA $565TEFC 0.5 3600 208-230/460 EE na Yes 56C FC0F536GEXCA 15 $269TEFC 0.5 1800 200-208 EE na Yes 56C FC0F518HEXCA $321TEFC 0.5 1800 208-230/460 EE na Yes 56C FC0F518GEXCA 2 $251TEFC 0.5 1800 208-230/460 EE na Yes 56C FC0F518GEXCA 2 $326TEFC 0.5 1200 208-230/460 EE na Yes 56C FC0F512GEXCA 15 $443TEFC 0.5 900 208-230/460 EE na N 56C FC0F509GEXCA $601TEFC 0.75 3600 208-230/460 EE na Yes 56C FCF7536GEXCA 15 $299TEFC 0.75 1800 208-230/460 EE na Yes 56C FCF7518GEXCB 15 $352TEFC 0.75 1800 200-208 EE na Yes 56C FCF7518HEXCA $343TEFC 0.75 1200 208-230/460 EE na Yes 56C FCF7512GEXCA 15 $456TEFC 0.75 1200 230/460 EE na N 143TC FCF7512AEXCA $456TEFC 0.75 900 208-230/460 EE na N 56C FCF7509GEXCA $639TEFC 0.75 900 230/460 EE na N 145TC FCF7509AEXCA $639TEFC 1 3600 208-230/460 EE na Yes 56C FC00136GEXCA 15 $334TEFC 1 1800 208-230/460 EE na Yes 56C FC00118GEXCA 15 $361TEFC 1 1800 200-208 EE na Yes 56C FC00118HEXCA $370TEFC 1 1800 208-230/460 EE na Yes 56C FC00118GEXCA 2 $285TEFC 1 1800 230/460 EE na Yes 143TC FC00118AEXCB $382TEFC 1 1200 230/460 EE na Yes 56C FC00112AEXC5A $459TEFC 1 1200 230/460 EE na Yes 145TC FC00112AEXC4A $459


140

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 1.5 3600 230/460 EE na Yes 56C FC1F536AEXC5A $410TEFC 1.5 3600 230/460 EE na N 143TC FC1F536AEXC4A $410TEFC 1.5 1800 230/460 EE na Yes 56C FC1F518AEXCA $404TEFC 1.5 1800 200-208 EE na Yes 145TC FC1F518HEXCA $390TEFC 1.5 1800 208-230/460 EE na Yes 56C FC1F518GEXCA 2 $301TEFC 1.5 1800 230/460 EE na Yes 145TC FC1F518AEXCB $404TEFC 1.5 1200 230/460 EE na N 145TC FC1F512AEXCB $487TEFC 2 3600 230/460 EE na N 56C FC00236AEXCA $474TEFC 2 3600 230/460 EE na N 145TC FC00236AEXCA $474TEFC 2 1800 230/460 EE na Yes 56C FC00218AEXCA $437TEFC 2 1800 200-208 EE na Yes 145TC FC00218HEXCA $429TEFC 2 1800 208-230/460 EE na Yes 56C FC00218GEXCA 2 $318TEFC 2 1800 230/460 EE na Yes 145TC FC00218AEXCB $437TEFC 2 1200 230/460 EE na Yes 184TCY FC00212AEXCA 9,47 $722TEFC 3 3600 208-230/460 EE na N 56C FC00336GEXCA $515TEFC 3 3600 230/460 PE na Yes 182TCY FC00336APXCA 9 $724TEFC 3 1800 230/460 PE na Yes 182TC FC00318APXCB $675TEFC 5 3600 230/460 PE na Yes 184TCY FC00536APXCA 9 $857TEFC 5 1800 230/460 PE na Yes 184TC FC00518APXCB $798TEFC 7.5 3600 230/460 PE na Yes 213TCY FC7F536APXCA 9 $1,059TEFC 7.5 1800 230/460 PE na Yes 213TC FC7F518APXCB $1,027TEFC 10 3600 230/460 PE na Yes 215TCY FC01036APXCA 9 $1,248TEFC 10 1800 230/460 PE na Yes 215TC FC01018APXCA 9 $1,156TEFC 15 3600 230/460 PE na Yes 254TCY FC01536APXCA 9 $1,705TEFC 15 1800 230/460 PE na Yes 254TC FC01518APXCA 9 $1,588TEFC 20 3600 230/460 PE na Yes 256TCY FC02036APXCA 9 $2,064TEFC 20 1800 230/460 PE na Yes 256TCY FC02018APXCA 9 $1,858TEFC 40 1800 230/460 EE na Yes 324TC FC04018AEXCA $3,258TEFC 50 1800 230/460 EE na Yes 326TC FC05018AEXCA $3,825TEFC 60 1800 230/460 EE na N 364TC FC06018AEXCA $5,619TEFC 75 1800 230/460 EE na N 365TC FC07518AEXCA $6,846TEFC 100 1800 230/460 EE na N 405TC FC10018AEXCA $8,539TEFC 125 1800 230/460 EE na N 444TC FC12518AEXCA $11,145TEFC 150 1800 460 EE na N 445TC FC15018BEXCA $13,008TEFC 200 1800 460 EE na N 445TC FC20018BEXCA $15,262


C Face, Footless IP44Enclosure HP Synch Voltage Efficiency Inverter Norm. Frame Notes US List

RPM Class Torque/Spd Stock PriceTENV 0.25 3600 208-230/460 EE na N 56C NVF2536GEXFA $236TENV 0.25 1800 230/460 EE na Yes 56C NVF2518AEXFA 15 $257TENV 0.25 1800 230/460 PE na Yes 56C NVF2518APXFA $348TENV 0.25 1200 230/460 EE na Yes 56C NVF2512AEXFA 15 $388TENV 0.25 1200 230/460 PE na N 56C NVF2512APXFA $517TEFC 0.25 900 208-230/460 EE na N 56C FCF2509GEXFA $488TENV 0.33 3600 230/460 EE na Yes 56C NVF3336AEXFA $245TENV 0.33 3600 230/460 PE na N 56C NVF3336APXFA $325TENV 0.33 1800 230/460 EE na Yes 56C NVF3318AEXFA 15 $230TEFC 0.33 1800 208-230/460 EE na Yes 56C FCF3318GEXFA 2 $199TENV 0.33 1800 230/460 PE na Yes 56C NVF3318APXFA $370TENV 0.33 1200 230/460 EE na Yes 56C NVF3312AEXFA 15 $385TENV 0.33 1200 230/460 PE na Yes 56C NVF3312APXFA $526TEFC 0.33 900 208-230/460 EE na N 56C FCF3309GEXFA $531


141

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 0.5 3600 208-230/460 EE na Yes 56C FC0F536GEXFA 15 $250TEFC 0.5 3600 230/460 PE na Yes 56C FC0F536APXFA $347TEFC 0.5 1800 208-230/460 EE na Yes 56C FC0F518GEXFB 15 $271TEFC 0.5 1800 230/460 PE na Yes 56C FC0F518APXFA $423TEFC 0.5 1200 208-230/460 EE na Yes 56C FC0F512GEXFA 15 $412TEFC 0.5 1200 230/460 PE na Yes 56C FC0F512APXFA $577TEFC 0.5 900 208-230/460 EE na Yes 56C FC0F509GEXFA $566TEFC 0.75 3600 208-230/460 EE na Yes 56C FCF7536GEXFA 15 $278TEFC 0.75 3600 230/460 PE na Yes 56C FCF7536APXFA $344TEFC 0.75 1800 208-230/460 EE na Yes 56C FCF7518GEXFB 15 $287TEFC 0.75 1800 230/460 PE na Yes 56C FCF7518APXFA $467TEFC 0.75 1200 208-230/460 EE na Yes 56C FCF7512GEXF5A 15 $424TEFC 0.75 1200 208-230/460 EE na N 143TC FCF7512GEXF4A $424TEFC 0.75 1200 230/460 PE na N 143TC FCF7512APXFA $595TEFC 0.75 900 208-230/460 EE na Yes 56C FCF7509GEXF5A $600TEFC 0.75 900 208-230/460 EE na Yes 145TC FCF7509GEXF4A $600TEFC 1 3600 208-230/460 EE na Yes 56C FC00136GEXF5A 15 $312TEFC 1 3600 208-230/460 EE na Yes 143TC FC00136GEXF4A 15 $312TEFC 1 3600 230/460 PE na Yes 56C FC00136APXF5A $450TEFC 1 3600 230/460 PE na Yes 143TC FC00136APXFYA 50 $541TEFC 1 3600 230/460 PE na N 143TC FC00136APXF4A $450TEFC 1 1800 208-230/460 EE na Yes 56C FC00118GEXF5A 15 $305TEFC 1 1800 208-230/460 EE na Yes 143TC FC00118GEXF4A 2 $278TEFC 1 1800 230/460 EE na Yes 143TC FC00118AEXFA 15 $305TEFC 1 1800 230/460 PE na Yes 56C FC00118APXF5A $477TEFC 1 1800 230/460 PE na Yes 143TC FC00118APXFYA 50 $649TEFC 1 1800 230/460 PE na Yes 143TC FC00118APXF4A $477TEFC 1 1200 230/460 EE na Yes 56C FC00112AEXF5A $453TEFC 1 1200 230/460 EE na Yes 145TC FC00112AEXF4A 15 $453TEFC 1 1200 230/460 PE na N 56C FC00112APXF5A $639TEFC 1 1200 230/460 PE na N 145TC FC00112APXF4A $639TEFC 1.5 3600 230/460 EE na Yes 56C FC1F536AEXF5A 15 $373TEFC 1.5 3600 230/460 EE na N 143TC FC1F536AEXF4A $400TEFC 1.5 3600 230/460 PE na N 56C FC1F536APXF5A $544TEFC 1.5 3600 230/460 PE na Yes 143TC FC1F536APXFYA 50 $723TEFC 1.5 3600 230/460 PE na N 143TC FC1F536APXF4A $544TEFC 1.5 1800 230/460 EE na Yes 56C FC1F518AEXF5A $321TEFC 1.5 1800 208-230/460 EE na Yes 56C FC1F518GEXF5A 2 $283TEFC 1.5 1800 208-230/460 EE na Yes 145TC FC1F518GEXF4A 2 $283TEFC 1.5 1800 230/460 EE na Yes 145TC FC1F518AEXF4A $321TEFC 1.5 1800 230/460 PE na Yes 56C FC1F518APXFA $526TEFC 1.5 1800 230/460 PE na Yes 145TC FC1F518APXFYA 50 $699TEFC 1.5 1800 230/460 PE na Yes 145TC FC1F518APXFNA $526TEFC 1.5 1200 208-230/460 EE na Yes 145TC FC1F512GEXFA $508TEFC 1.5 1200 230/460 EE na Yes 182TC FC1F512AEXFA $664


142

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 2 3600 230/460 EE na Yes 56C FC00236AEXF5A 15 $464TEFC 2 3600 230/460 EE na Yes 145TC FC00236AEXF4A 15 $464TEFC 2 3600 230/460 PE na N 56C FC00236APXF5A $633TEFC 2 3600 230/460 PE na Yes 145TC FC00236APXFYA 50 $813TEFC 2 3600 230/460 PE na N 145TC FC00236APXF4A $633TEFC 2 1800 230/460 EE na Yes 56C FC00218AEXF5A $354TEFC 2 1800 230/460 EE na Yes 145TC FC00218AEXF4A 15 $343TEFC 2 1800 208-230/460 EE na Yes 56C FC00218GEXF5A 2 $303TEFC 2 1800 208-230/460 EE na Yes 145TC FC00218GEXF4A 2 $293TEFC 2 1800 230/460 PE na Yes 56C FC00218APXF5A $574TEFC 2 1800 230/460 PE na Yes 145TC FC00218APXFYA 50 $747TEFC 2 1800 230/460 PE na Yes 145TC FC00218APXF4A $574TEFC 2 1200 230/460 EE na Yes 184TC FC00212AEXFA $483TEFC 3 3600 208-230/460 EE na N 56C FC00336GEXF5A $483TEFC 3 3600 208-230/460 EE na N 145TC FC00336GEXF4A $483TEFC 3 3600 230/460 EE na Yes 182TC FC00336AEXFA $659TEFC 3 1800 208-230/460 EE na Yes 145TC FC00318GEXFB $423TEFC 3 1800 230/460 EE na Yes 182TC FC00318AEXFA $617TEFC 3 1800 230/460 PE na Yes 182TC FC00318APXFA $697TEFC 3 1200 230/460 EE na Yes 213TC FC00312AEXFA $851TEFC 5 3600 230/460 EE na Yes 184TC FC00536AEXFA $783TEFC 5 1800 230/460 EE na Yes 184TC FC00518AEXFNA $528TEFC 5 1800 230/460 EE na Yes 184TC FC00518AEXFYA $723TEFC 5 1800 230/460 PE na Yes 184TC FC00518APXFA $819TEFC 5 1200 230/460 EE na Yes 215TC FC00512AEXFA $1,230TEFC 7.5 3600 230/460 EE na Yes 213TC FC7F536AEXFA $972TEFC 7.5 1800 230/460 EE na Yes 213TC FC7F518AEXFA $926TEFC 7.5 1800 230/460 PE na Yes 213TC FC7F518APXFA $1,050TEFC 10 3600 230/460 EE na Yes 215TC FC01036AEXFA $1,147TEFC 10 1800 230/460 EE na Yes 215TC FC01018AEXFA $1,040TEFC 10 1800 230/460 PE na Yes 215TC FC01018APXFA $1,178



143

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es





CONDUIT BOX: Mounting of stock box kits (price includes box).101 Convert to cast iron 180-320 $188 103

360-445 $376 103102 Add auxiliary box attached to main conduit box 140-445 $618 103103 Drill drain hole 56-449 $188 103


360-449 $251DRAINS: Install one automatic breather drain in each motor end bracket. Note: Mounting position must be specified

112 Stainless steel T-drain 180-449 $618DRIP COVERS: Mounting of stock canopy kits (price includes kit).

116 Install canopy kit to allow for vertical shaft down operation. 48, 56, 140 $251Note: This modification does not provide vertical lifting provisions. 180-210 $251END BRACKET: Modify a foot mounted motor to include a C-Face end bracket.Note: Please add seal modification seperately if required.


Non-Nafta motors are non-NEMA BAGREASE FITTINGS: Install a grease fitting on each bearing.



MILL AND CHEMICAL DUTY: Add features for additional reliability in Mill and Chem duty applications.139 Convert to cast iron fan shroud and conduit box. 180-280 $493 103

320-400 $744 103440-449 $1,245 103




144

General

Information

CM

100C

M 200

CM

300F

ootnotes

Modifications Available to CM303 MotorsMOUNTING: Move conduit box to allow different mounting configurations.





144 F-1 to W7 180-280 $251 Note: Not available on L180-L210 frames 320-449 $376 SEALS: Addition of shaft seal.




159 Mount a set of qty (3) normally closed thermostats 48,56,140 $224180-360 $493440-449 $618 107


145

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Sine Wave ClassGeneral Purpose SeriesCM306 Family - Open EE Rolled Steel AC Motors







(24 / 12)




Conduit Box: F1 location. Diagonally split, rotatable in 90 degree incrementsBearing Type: Permanently lubricated, double shielded ball bearingsBearing Protection: Shaft slinger on drive endShaft Material: High strength carbon steelNameplate Material: AluminumDrain Type & Location: Weep holes on both end shields


146

General

Information

CM

100C

M 200

CM

300F

ootnotes

Sine Wave Class, General Purpose SeriesCM306 - Open EE Rolled Steel AC Motors


RPM Class Torque/Spd Stock CM306- PriceODP 3 1800 230/460 EE na Yes 182T DP00318AEXHA 9 $297ODP 3 1200 230/460 EE na Yes 213T DP00312AEXHA 9 $453ODP 5 3600 230/460 EE na Yes 182T DP00536AEXHA 9 $323ODP 5 1800 230/460 EE na Yes 184T DP00518AEXHA 9 $326ODP 5 1200 230/460 EE na Yes 215T DP00512AEXHA 9 $567ODP 7.5 3600 230/460 EE na Yes 184T DP7F536AEXHA 9 $464ODP 7.5 1800 230/460 EE na Yes 213T DP7F518AEXHA 9 $474ODP 7.5 1200 230/460 EE na Yes 254T DP7F512AEXHA 9 $738ODP 10 3600 230/460 EE na Yes 213T DP01036AEXHA 9 $570ODP 10 1800 230/460 EE na Yes 215T DP01018AEXHA 9 $572ODP 10 1200 230/460 EE na Yes 256T DP01012AEXHA 9 $863ODP 15 3600 230/460 EE na Yes 215T DP01536AEXHA 9 $734ODP 15 1800 230/460 EE na Yes 254T DP01518AEXHA 9 $760ODP 15 1200 230/460 EE na Yes 284T DP01512AEXHA 9 $1,112ODP 20 3600 230/460 EE na Yes 254T DP02036AEXHA 9 $865ODP 20 1800 230/460 EE na Yes 256T DP02018AEXHA 9 $928ODP 20 1200 230/460 EE na Yes 286T DP02012AEXHA 9 $1,363ODP 25 3600 230/460 EE na Yes 256T DP02536AEXHA 9 $1,055ODP 25 1800 230/460 EE na Yes 284T DP02518AEXHA 9 $1,080ODP 30 3600 230/460 EE na Yes 284TS DP03036AEXHA 9 $1,259ODP 30 1800 230/460 EE na Yes 286T DP03018AEXHA 9 $1,254



RPM Class Torque/Spd Stock PriceODP 3 1800 230/460 EE na Yes 182TC DP00318AEXCA 9 $372ODP 3 1200 230/460 EE na Yes 213TC DP00312AEXCA 9 $528ODP 5 3600 230/460 EE na Yes 182TC DP00536AEXCA 9 $398ODP 5 1800 230/460 EE na Yes 184TC DP00518AEXCA 9 $401ODP 5 1200 230/460 EE na Yes 215TC DP00512AEXCA 9 $642ODP 7.5 3600 230/460 EE na Yes 184TC DP7F536AEXCA 9 $539ODP 7.5 1800 230/460 EE na Yes 213TC DP7F518AEXCA 9 $549ODP 7.5 1200 230/460 EE na Yes 254TC DP7F512AEXCA 9 $813ODP 10 3600 230/460 EE na Yes 213TC DP01036AEXCA 9 $645ODP 10 1800 230/460 EE na Yes 215TC DP01018AEXCA 9 $647ODP 10 1200 230/460 EE na Yes 256TC DP01012AEXCA 9 $961ODP 15 3600 230/460 EE na Yes 215TC DP01536AEXCA 9 $809ODP 15 1800 230/460 EE na Yes 254TC DP01518AEXCA 9 $859ODP 15 1200 230/460 EE na Yes 284TC DP01512AEXCA 9 $1,251ODP 20 3600 230/460 EE na Yes 254TC DP02036AEXCA 9 $963ODP 20 1800 230/460 EE na Yes 256TC DP02018AEXCA 9 $1,027ODP 20 1200 230/460 EE na Yes 286TC DP02012AEXCA 9 $1,501ODP 25 3600 230/460 EE na Yes 256TC DP02536AEXCA 9 $1,149ODP 25 1800 230/460 EE na Yes 284TC DP02518AEXCA 9 $1,218ODP 30 3600 230/460 EE na Yes 284TSC DP03036AEXCA 9 $1,398ODP 30 1800 230/460 EE na Yes 286TC DP03018AEXCA 9 $1,393



147

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es




















148

General

Information

CM

100C

M 200

CM

300F

ootnotes


Sine Wave ClassGeneral Purpose SeriesCM307 Family - SE/EE/PE/NP AC Motors



Frequency: 60 Hz Duty Cycle: Continuous SE = Standard efficient motors not requiring EPAct efficiencies. Ambient: 40° C Insulation: Class F

Service Factor: 1.15 Temp. Rise: Class B EE = Energy Efficient motors that meet EPAct efficiency levels.

Application InformationDesigned for all general purpose industrial applications in a clean and dry environment.

PE = Premium Efficient motors that exceed EPAct efficiency levels



SE (24 / 12), EE (24 / 12),PE (36 / 24), NP (36 / 24)Nameplate Agency Approvals:CE, CSA, UR

180T - 449T FramesMaterials: Cast iron frame and end shields, steel conduit box.Conduit Box: F1, Diagonally split, rotatable in 90 degree increments.Bearing Type: BallBearing Protection: (360 T - 449T frames) Inner capsShaft Material: High strength carbon steelNameplate Material: Stainless steel or aluminumDrain Type & Location: None


149

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Sine Wave Class, General Purpose SeriesCM307 - Open EE/PE/NP AC Motors


RPM Class Torque/Spd Stock CM307- PriceODP 1.5 1200 230/460 NP na N 213T DP1F512ANXHA 35 $725ODP 2 1200 230/460 NP na N 213T DP00212ANXHA 35 $846ODP 3 3600 230/460 NP na N 182T DP00336ANXHA 35 $572ODP 3 1800 230/460 NP na Yes 182T DP00318ANXHA $467ODP 3 1200 230/460 NP na N 213T DP00312ANXHA $1,057ODP 5 3600 230/460 NP na Yes 182T DP00536ANXHA 9 $572ODP 5 1800 230/460 NP na N 213T DP00518ANXHA 35 $748ODP 5 1200 230/460 NP na N 215T DP00512ANXHA $1,409ODP 5 900 460 PE na N 254T DP00509BPXHA $1,772ODP 7.5 3600 230/460 NP na Yes 184T DP7F536ANXHA 9 $832ODP 7.5 1800 230/460 NP na N 184T DP7F518ANXHA $832ODP 7.5 1200 230/460 NP na N 254T DP7F512ANXHA $2,465ODP 7.5 900 460 PE na N 256T DP7F509BPXHA $2,256ODP 10 3600 230/460 NP na Yes 213T DP01036ANXHA 75 $893ODP 10 1800 230/460 NP na N 254T DP01018ANXHA 35 $1,215ODP 10 1200 230/460 NP na N 256T DP01012ANXHA $2,705ODP 15 3600 230/460 NP na Yes 215T DP01536ANXHA 9 $1,336ODP 15 1800 230/460 NP na N 256T DP01518ANXHA $1,413ODP 15 1200 230/460 NP na N 286T DP01512ANXHA $2,793ODP 15 900 460 PE na N 286T DP01509BPXHA $3,516ODP 20 3600 230/460 NP na Yes 254T DP02036ANXHA 9 $1,631ODP 20 1800 230/460 NP na Yes 256T DP02018ANXHA 9 $1,483ODP 20 1800 230/460 PE na Yes 256T DP02018APXHA 75 $1,483ODP 20 1200 230/460 NP na N 286T DP02012ANXHA $2,875ODP 20 900 460 PE na N 324T DP02009BPXHA $4,236ODP 25 3600 230/460 NP na Yes 256T DP02536ANXHA 9 $1,896ODP 25 1800 230/460 NP na N 284T DP02518ANXHA $1,723ODP 25 1200 230/460 NP na N 326T DP02512ANXHA $2,954ODP 25 1200 230/460 EE na Yes 324T DP02512AEXHA 9 $2,067ODP 25 900 460 PE na N 326T DP02509BPXHA $5,018ODP 30 3600 230/460 NP na Yes 284TS DP03036ANXHA 9 $1,740ODP 30 1800 230/460 NP na N 286T DP03018ANXHA 35 $2,002ODP 30 1200 230/460 EE na N 326T DP03012AEXHA 9 $2,364ODP 30 1200 230/460 NP na N 326T DP03012ANXHA $3,074ODP 30 900 460 PE na N 364T DP03009BPXHA $5,692ODP 40 3600 230/460 NP na N 286TS DP04036ANXHA $2,861ODP 40 1800 230/460 NP na Yes 324T DP04018ANXHA 9 $2,492ODP 40 1200 230/460 EE na N 364T DP04012AEXHA $3,885ODP 40 1200 230/460 NP na N 365T DP04012ANXHA $5,278ODP 40 900 460 PE na N 365T DP04009BPXHA $7,049ODP 50 3600 230/460 NP na N 324TS DP05036ANXHA $3,399ODP 50 1800 230/460 NP na Yes 326T DP05018ANXHA 9 $2,904ODP 50 1775 230/460 PE na 0 326T DP05017APXHA $2,850ODP 50 1200 230/460 EE na N 365T DP05012AEXHA $4,539ODP 50 1200 230/460 NP na N 365T DP05012ANXHA $5,278ODP 50 900 460 PE na N 404T DP05009BPXHA $8,400ODP 60 3600 230/460 EE na N 326TS DP06036AEXHA $3,912ODP 60 1800 230/460 NP na Yes 364T DP06018ANXHA 9 $3,514ODP 60 1200 460 EE na N 404T DP06012BEXHA $5,295ODP 60 1200 230/460 NP na Yes 404T DP06012ANXHA $6,158ODP 60 900 460 PE na N 405T DP06009BPXHA $9,738ODP 75 3600 230/460 NP na N 364TS DP07536ANXHA $5,155ODP 75 1800 230/460 NP na Yes 365T DP07518ANXHA 9 $4,336ODP 75 1200 460 EE na N 405T DP07512BEXHA $6,306ODP 75 1200 230/460 NP na Yes 405T DP07512ANXHA $7,333ODP 75 900 460 PE na N 444T DP07509BPXHA $11,665ODP 100 3600 230/460 NP na N 365TS DP10036ANXHA $6,400


150

General

Information

CM

100C

M 200

CM

300F

ootnotes


ODP 100 1800 230/460 NP na Yes 404T DP10018ANXHA 75 $5,529ODP 100 1200 460 EE na N 444T DP10012BEXHA $7,987ODP 100 1200 230/460 NP na Yes 444T DP10012ANXHA $9,287ODP 125 3600 460 NP na N 404TS DP12536BNXHA $7,965ODP 125 1800 460 NP na Yes 405T DP12518BNXHA 9 $6,620ODP 125 1200 460 EE na N 445T DP12512BEXHA $9,809ODP 125 1200 460 NP na Yes 445T DP12512BNXHA $11,406ODP 150 3600 460 NP na N 405TS DP15036BNXHA $9,688ODP 150 1800 460 NP na N 444T DP15018BNXHA $9,561ODP 150 1200 460 EE na N 445T DP15012BEXUA 5 $10,874ODP 150 1200 460 NP na Yes 445T DP15012BNXHA $12,643ODP 200 3600 460 EE na N 444TS DP20036BEXHA 4 $12,996ODP 200 3600 460 NP na Yes 444TS DP20036BNXHA $15,071ODP 200 1800 460 EE na N 445TS DP20018BEXHSA 4 $9,221ODP 200 1800 460 NP na Yes 445T DP20018BNXHA $12,079ODP 200 1800 460 EE na N 445T DP20018BEXHTA $9,221ODP 200 1200 460 EE na N 445T DP20012BEXUA 4,5 $14,261ODP 200 1200 460 NP na Yes 447T DP20012BNXHA $15,919ODP 250 3600 460 EE na N 445TS DP25036BEXHA 4 $15,315ODP 250 3600 460 NP na Yes 445TS DP25036BNXHA $18,018ODP 250 1800 460 EE na N 445TS DP25018BEXHA 4 $11,491ODP 250 1800 460 NP na Yes 447T DP25018BNXHA $18,327ODP 250 1200 460 EE na N 447T DP25012BEXUA 4,5 $19,632ODP 250 1200 460 NP na Yes 449T DP25012BNXHA $22,091ODP 300 3600 460 EE na N 445TS DP30036BEXHA 4 $19,593ODP 300 3600 460 NP na Yes 445TS DP30036BNXHA $23,456ODP 300 1800 460 EE na N 445TS DP30018BEXHA 4 $14,885ODP 300 1800 460 NP na Yes 449T DP30018BNXHA $19,231ODP 300 1200 460 NP na N 449T DP30012BNXHA 2,20 $26,297ODP 350 3600 460 EE na N 445TS DP35036BEXHA 4 $21,174ODP 350 3600 460 NP na Yes 447TS DP35036BNXHA $26,137ODP 350 1800 460 EE na N 447TS DP35018BEXHA 4 $18,090ODP 350 1800 460 NP na Yes 449T DP35018BNXHA $22,402ODP 400 3600 460 EE na N 447TS DP40036BEXHA 4 $24,527ODP 400 3600 460 NP na Yes 449TS DP40036BNXHA $30,342ODP 400 1800 460 EE na N 449TS DP40018BEXHA 4,6 $19,619ODP 400 1800 460 NP na Yes 449T DP40018BNXHA $27,522ODP 450 3600 460 EE na N 447TS DP45036BEXHA 4 $26,554ODP 450 3600 460 NP na Yes 449TS DP45036BNXHA $32,986ODP 450 1800 460 NP na N 449TS DP45018BNXHA 4,6 $32,958ODP 500 3600 460 NP na N 449TS DP50036BNXHA 4 $36,168



151

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es




















152

General

Information

CM

100C

M 200

CM

300F

ootnotes


Component ClassHarsh Environment SeriesCM311 Family - Severe Duty AC Motors



Frequency: 60 Hz Duty Cycle: Continuous SE = Standard efficient motors not requiring EPAct efficiencies.Ambient: 40° C Insulation: Class F

Service Factor: 1.15 Temp. Rise: Class B EE = Energy Efficient motors that meet EPAct efficiency levels.PE = Premium Efficient motors that exceed EPAct efficiency levels.Application Information

Severe Duty motors are built with rugged cast iron construction and key features for long life in moist, contaminated environments such as chemical plants, petroleum reÞneries and paper mills.

NP = NEMA Premium efficient motors.Warranty (From Date Of Manufacture / From Date Of Installation):

SE (24 / 12), EE (24 / 12),PE (36 / 24), NP (36 / 24)Nameplate Agency Approvals:CE, CSA, UR, IEEE45 / ABS (10)

56 - 140T FramesMaterials: (SE & EE) - Plated steel frame, conduit box and fan

shroud, cast iron end shields(PE & NP) - Cast iron frame, conduit box, fan shroud, and end shields

Conduit Box: Oversized, top mounted with F1 & F2 lead outlets. Cast iron frames have F1 location.

Bearing Type: (SE & EE) - Double sealed, permanently lubricated ball bearings(PE & NP) - Double shielded, regreasable ball bearings with grease relief fittings

Bearing Protection: (SE & EE) - Lip seals on both ends of the motor(PE & NP) - Non-metallic V-ring shaft and slinger on drive end

Shaft Material: 400 Series Stainless Steel shaftNameplate Material: (SE & EE) - Adhesive Mylar; (PE & NP) - Stainless SteelDrain Type & Location: T-drain in drive end shield. Weep hole in opposite drive

end shield. Fan cooled. TENV has T-drain both ends for SE & EE.

180T - 449T FramesMaterials: Cast iron construction: frame, conduit box, fan cover, end shields and inner capsConduit Box: F1 location, Diagonally split, neoprene gasketed, rotatable in 90 degree increments and NPF threaded lead

hole. UL listed clamp type grounding lug in box.Bearing Type: Regreasable, open ball bearings with PLS (180T - 449T frames).Bearing Protection: Non-metallic V-ring shaft slinger on drive endShaft Material: High strength carbon steelNameplate Material: Stainless SteelDrain Type & Location: Stainless steel T-drains mounted in both end shieldsAdditional Features: The motor stator and rotor are completely epoxy coated for corrosion protection.

Severe duty motors are provided with alemite grease fittings for easy bearing maintenanceSilicone rubber sealed fits provide superior protection against contaminates entering the motor body


153

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Sine Wave Class, Harsh Environment SeriesCM311 Family - Severe Duty AC Motors


RPM Class Torque/Spd Stock CM311- PriceTENV 0.33 1800 208-230/460 SE na Yes 56 NVF3318GSXHA 15 $351TENV 0.33 1800 230/460 EE na Yes 56 NVF3318AEXHA $369TENV 0.33 1200 230/460 EE na N 56 NVF3312AEXHA $489TENV 0.5 3600 230/460 SE na N 56 NV0F536ASXHA $382TENV 0.5 3600 230/460 EE na N 56 NV0F536AEXHA $393TEFC 0.5 1800 208-230/460 SE na Yes 56 FC0F518GSXHA 15 $385TENV 0.5 1800 230/460 EE na Yes 56 NV0F518AEXHA $406TENV 0.5 1800 230/460 PE na N 143T NV0F518APXHA 50 $689TENV 0.5 1200 230/460 EE na N 56 NV0F512AEXHA $536TENV 0.5 1200 230/460 PE na N 143T NV0F512APXHA 50 $854TEFC 0.75 3600 208-230/460 SE na Yes 56 FCF7536GSXHA 15 $413TENV 0.75 3600 230/460 EE na N 56 NVF7536AEXHA $420TEFC 0.75 1800 208-230/460 SE na Yes 56 FCF7518GSXHA 15 $414TENV 0.75 1800 230/460 EE na Yes 56 NVF7518AEXHA $437TENV 0.75 1800 230/460 PE na N 143T NVF7518APXHA 50 $733TEFC 0.75 1200 208-230/460 SE na N 143T FCF7512GSXHA 15 $543TENV 0.75 1200 230/460 EE na N 56 NVF7512AEXHA $549TEFC 0.75 1200 230/460 EE na N 143T FCF7512AEXHA $549TENV 0.75 1200 230/460 PE na Yes 143T NVF7512APXHA 50 $872TEFC 1 3600 208-230/460 SE na N 56 FC00136GSXHA 15 $448TENV 1 3600 230/460 EE na N 56 NV00136AEXHA $458TENV 1 3600 230/460 NP na Yes 143T NV00136ANXHA 50 $726TENV 1 1800 230/460 SE na Yes 56 NV00118ASXHA $421TEFC 1 1800 230/460 EE na N 56 FC00118AEXH5A $445TEFC 1 1800 230/460 EE na Yes 143T FC00118AEXH4A $445TENV 1 1800 230/460 NP na Yes 143T NV00118ANXHA 50 $743TEFC 1 1200 230/460 EE na N 56 FC00112AEXH5A $568TEFC 1 1200 230/460 EE na Yes 145T FC00112AEXH4A $568TEFC 1 1200 230/460 NP na Yes 145T FC00112ANXHA 50 $916TEFC 1 900 460 PE na Yes L182T FC00109BPXHA $938TEFC 1.5 3600 208-230/460 SE na Yes 56 FC1F536GSXHA 15 $515TEFC 1.5 3600 230/460 EE na N 56 FC1F536AEXH5A $519TEFC 1.5 3600 230/460 EE na N 143T FC1F536AEXH4A $519TEFC 1.5 3600 230/460 NP na Yes 143T FC1F536ANXHA 50 $819TEFC 1.5 1800 208-230/460 SE na N 56 FC1F518GSXHA $451TEFC 1.5 1800 230/460 EE na N 56 FC1F518AEXH5A $463TEFC 1.5 1800 230/460 EE na Yes 145T FC1F518AEXH4A $463TEFC 1.5 1800 230/460 NP na Yes 145T FC1F518ANXHA 50 $791TEFC 1.5 1200 230/460 NP na Yes L182T FC1F512ANXHA $692TEFC 1.5 1200 460 PE na Yes 182T FC1F512BPXHA $692TEFC 1.5 900 460 PE na Yes L184T FC1F509BPXHA $1,108TEFC 2 3600 230/460 SE na N 56 FC00236ASXHA $578TEFC 2 3600 230/460 EE na N 56 FC00236AEXH5A $592TEFC 2 3600 230/460 EE na Yes 145T FC00236AEXH4A $592TEFC 2 3600 230/460 NP na Yes 145T FC00236ANXHA 50 $907TEFC 2 1800 230/460 SE na N 56 FC00218ASXHA $483TEFC 2 1800 230/460 EE na N 56 FC00218AEXH5A $421TEFC 2 1800 230/460 EE na Yes 145T FC00218AEXH4A $501TEFC 2 1800 230/460 NP na Yes 145 FC00218ANXHA 50 $839TEFC 2 1200 230/460 NP na Yes L184T FC00212ANXHA $773TEFC 2 1200 460 PE na Yes L184T FC00212BPXHA $773TEFC 2 900 460 PE na Yes L213T FC00209BPXHA $1,323


154

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 3 3600 230/460 EE na N 182T FC00336AEXHA $598TEFC 3 3600 460 PE na Yes 182T FC00336BPXHA $688TEFC 3 3600 230/460 NP na Yes 182T FC00336ANXHA $688TEFC 3 1800 230/460 NP na Yes L182T FC00318ANXHA $668TEFC 3 1800 460 PE na Yes 182T FC00318BPXHA $668TEFC 3 1200 460 PE na Yes 213T FC00312BPXHA $940TEFC 3 1200 230/460 NP na Yes 213T FC00312ANXHA $940TEFC 3 900 460 PE na Yes L215T FC00309BPXHA $1,653TEFC 5 3600 230/460 NP na Yes 184T FC00536ANXHA $816TEFC 5 3600 460 PE na Yes 184T FC00536BPXHA $816TEFC 5 1800 230/460 NP na Yes L184T FC00518ANXHA 35 $784TEFC 5 1800 460 PE na Yes L184T FC00518BPXHA $784TEFC 5 1200 460 PE na Yes L215T FC00512BPXHA $1,335TEFC 5 1200 230/460 NP na Yes L215T FC00512ANXHA $1,335TEFC 5 900 460 PE na Yes 254T FC00509BPXHA $2,197TEFC 7.5 3600 230/460 NP na Yes 213T FC7F536ANXHA $1,066TEFC 7.5 3600 460 PE na Yes 213T FC7F536BPXHA $1,066TEFC 7.5 1800 460 PE na Yes 213T FC7F518BPXHA $1,059TEFC 7.5 1800 230/460 NP na Yes L213T FC7F518ANXHA $1,059TEFC 7.5 1200 460 PE na Yes 254T FC7F512BPXHA $1,773TEFC 7.5 1200 230/460 NP na Yes 254T FC7F512ANXHA $1,773TEFC 7.5 900 460 PE na Yes 256T FC7F509BPXHA $2,776TEFC 10 3600 460 PE na Yes 215T FC01036BPXHA $1,249TEFC 10 3600 230/460 NP na Yes 215T FC01036ANXHA $1,249TEFC 10 1800 460 PE na Yes L215T FC01018BPXHA $1,181TEFC 10 1800 230/460 NP na Yes L215T FC01018ANXHA $1,181TEFC 10 1200 460 PE na Yes 256T FC01012BPXHA $2,175TEFC 10 1200 230/460 NP na Yes 256T FC01012ANXHA $2,175TEFC 10 900 460 PE na Yes 284T FC01009BPXHA $3,240TEFC 15 3600 460 PE na Yes 254T FC01536BPXHA $1,714TEFC 15 3600 230/460 NP na Yes 254T FC01536ANXHA $1,714TEFC 15 1800 230/460 NP na Yes 254T FC01518ANXHA $1,625TEFC 15 1800 460 PE na Yes 254T FC01518BPXHA $1,625TEFC 15 1200 460 PE na Yes 284T FC01512BPXHA $2,893TEFC 15 1200 230/460 NP na Yes 284T FC01512ANXHA $2,893TEFC 15 900 460 PE na Yes 286T FC01509BPXHA $4,221TEFC 20 3600 460 PE na Yes 256T FC02036BPXHA $2,064TEFC 20 3600 230/460 NP na Yes 256T FC02036ANXHA $2,064TEFC 20 1800 230/460 NP na Yes 256T FC02018ANXHA $1,941TEFC 20 1800 460 PE na Yes 256T FC02018BPXHA $1,941TEFC 20 1200 460 PE na Yes 286T FC02012BPXHA $3,590TEFC 20 1200 230/460 NP na Yes 286T FC02012ANXHA $3,590TEFC 20 900 460 PE na Yes 324T FC02009BPXHA $5,161TEFC 25 3600 460 PE na Yes 284TS FC02536BPXHA $2,585TEFC 25 3600 230/460 NP na Yes 284TS FC02536ANXHA $2,585TEFC 25 1800 230/460 NP na Yes 284T FC02518ANXHA $2,477TEFC 25 1800 460 PE na Yes 284T FC02518BPXHA $2,477TEFC 25 1200 230/460 NP na Yes 324T FC02512ANXHA $4,203TEFC 25 1200 460 PE na Yes 324T FC02512BPXHA $4,203TEFC 30 3600 460 PE na Yes 286TS FC03036BPXHA $3,040TEFC 30 3600 230/460 NP na Yes 286TS FC03036ANXHA $3,040TEFC 30 1800 460 PE na Yes 286T FC03018BPXHA $2,893TEFC 30 1800 230/460 NP na Yes 286T FC03018ANXHA $2,893TEFC 30 1200 230/460 NP na Yes 326T FC03012ANXHA $4,794TEFC 30 1200 460 PE na Yes 326T FC03012BPXHA $4,794


155

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 40 3600 230/460 EE na Yes 324TS FC04036AEXHA $3,288TEFC 40 3600 230/460 NP na Yes 324TS FC04036ANXHA $3,782TEFC 40 3600 460 PE na Yes 324TS FC04036BPXHA $3,782TEFC 40 1800 230/460 NP na Yes 324T FC04018ANXHA $3,749TEFC 40 1800 460 PE na Yes 324T FC04018BPXHA $3,749TEFC 40 1200 230/460 PE na N 364T FC04012APXHA $6,613TEFC 40 1200 460 NP na Yes 364T FC04012BNXHA $6,613TEFC 50 3600 460 PE na Yes 326TS FC05036BPXHA $4,839TEFC 50 3600 230/460 PE na Yes 326TS FC05036APXHA $4,839TEFC 50 1800 230/460 EE na Yes 326T FC05018AEXHA $3,819TEFC 50 1800 460 PE na Yes 326T FC05018BPXHTA $4,395TEFC 50 1800 230/460 NP na Yes 326T FC05018ANXHA $4,395TEFC 50 1800 460 PE na N 326TS FC05018BPXHSA $4,395TEFC 50 1200 230/460 EE na Yes 365T FC05012AEXHA $6,674TEFC 50 1200 460 NP na Yes 365T FC05012BNXHA $7,677TEFC 50 1200 230/460 PE na N 365T FC05012APXHA $7,677TEFC 60 3600 230/460 EE na Yes 364TS FC06036AEXHA $5,857TEFC 60 3600 230/460 PE na N 364TS FC06036APXHA $6,734TEFC 60 3600 460 NP na Yes 364TS FC06036BNXHA $6,734TEFC 60 1800 230/460 EE na Yes 364T FC06018AEXHA $5,737TEFC 60 1800 230/460 PE na N 364T FC06018APXHA $6,594TEFC 60 1800 460 PE na N 364TS FC06018BPXHA $6,594TEFC 60 1800 460 NP na Yes 364T FC06018BNXHA $6,594TEFC 60 1200 230/460 EE na Yes 404T FC06012AEXHA $7,768TEFC 60 1200 230/460 PE na N 404T FC06012APXHA $8,931TEFC 60 1200 460 NP na Yes 404T FC06012BNXHA $8,931TEFC 75 3600 230/460 EE na Yes 365TS FC07536AEXHA $7,183TEFC 75 3600 230/460 PE na N 365TS FC07536APXHA $8,267TEFC 75 3600 460 NP na Yes 365TS FC07536BNXHA $8,267TEFC 75 1800 230/460 EE na Yes 365T FC07518AEXHA $6,947TEFC 75 1800 230/460 NP na Yes 365T FC07518ANXHA $7,994TEFC 75 1800 460 PE na N 365TS FC07518BPXHSA $7,994TEFC 75 1800 460 PE na Yes 365T FC07518BPXHTA $7,994TEFC 75 1200 230/460 EE na Yes 405T FC07512AEXHA $8,630TEFC 75 1200 230/460 PE na N 405T FC07512APXHA $9,928TEFC 75 1200 460 NP na Yes 405T FC07512BNXHA $9,928TEFC 100 3600 230/460 PE na N 405TS FC10036APXHA $10,704TEFC 100 3600 460 NP na Yes 405TS FC10036BNXHA $10,704TEFC 100 1800 230/460 EE na Yes 405T FC10018AEXHA $8,583TEFC 100 1800 230/460 PE na N 405T FC10018APXHA $9,874TEFC 100 1800 460 NP na Yes 405T FC10018BNXHA $9,874TEFC 100 1800 460 PE na N 405TS FC10018BPXHA $9,874TEFC 100 1200 230/460 EE na Yes 444T FC10012AEXHA $11,628TEFC 100 1200 460 NP na Yes 444T FC10012BNXHA $13,371TEFC 125 3600 460 NP na Yes 444TS FC12536BNXHA $13,983TEFC 125 1800 460 EE na Yes 444T FC12518BEXHA $11,300TEFC 125 1800 460 NP na Yes 444T FC12518BNXHA $12,990TEFC 125 1800 460 PE na N 444TS FC12518BPXHA $12,990TEFC 125 1200 460 EE na Yes 445T FC12512BEXHA $13,996TEFC 125 1200 460 NP na Yes 445T FC12512BNXHA $16,107TEFC 150 3600 460 NP na Yes 445TS FC15036BNXHA $16,814TEFC 150 1800 460 EE na Yes 445T FC15018BEXHA $13,136TEFC 150 1800 460 NP na Yes 445T FC15018BNXHA $15,114TEFC 150 1800 460 PE na N 445TS FC15018BPXHA $15,114TEFC 150 1200 460 EE na Yes 445T FC15012BEXUA 5 $15,841TEFC 150 1200 460 NP na Yes 447T FC15012BNXUA 5 $19,514


156

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 200 3600 460 EE na Yes 445TS FC20036BEXHA 4 $18,475TEFC 200 3600 460 NP na Yes 445TS FC20036BNXHA $21,286TEFC 200 1800 460 EE na Yes 445T FC20018BEXUA 4,5 $15,919TEFC 200 1800 460 NP na Yes 447T FC20018BNXUA 5 $18,958TEFC 200 1800 460 PE na Yes 447TS FC20018BPXHA $18,958TEFC 200 1200 460 EE na Yes 447T FC20012BEXUA 4,5 $19,640TEFC 200 1200 460 NP na Yes 449T FC20012BNXUA 5 $21,832TEFC 250 3600 460 EE na Yes 447TS FC25036BEXHA 4 $24,479TEFC 250 3600 460 NP na Yes 447TS FC25036BNXHA $27,426TEFC 250 1800 460 SE na Yes 447TS FC25018BSXUA 5,75 $20,765TEFC 250 1800 460 EE na Yes 447TS FC25018BEXHB 4,75 $19,931TEFC 250 1800 460 EE na Yes 447T FC25018BEXUA 4,5 $19,931TEFC 250 1800 460 PE na Yes 449TS FC25018BPXHA $22,168TEFC 250 1800 460 NP na Yes 449T FC25018BNXUA 5 $22,168TEFC 250 1200 460 EE na Yes 449T FC25012BEXUA 4,5 $25,031TEFC 250 1200 460 NP na Yes 449T FC25012BNXHA 5 $28,190TEFC 300 3600 460 NP na Yes 449TS FC30036BNXHA 35 $34,009TEFC 300 1800 460 EE na Yes 449TS FC30018BEXHA 4 $23,208TEFC 300 1800 460 PE na Yes 449TS FC30018BPXHA $25,958TEFC 300 1800 460 NP na Yes 449T FC30018BNXUA 5 $25,958TEFC 350 3600 460 NP na Yes 449TS FC35036BNXHA $38,351TEFC 350 1800 460 NP na Yes 449T FC35018BNXUA 5 $30,203TEFC 400 3600 460 PE na Yes 449TS FC40036BPXHA $42,151



RPM Class Torque/Spd Stock PriceTENV 0.25 1800 208-230/460 SE na Yes 56C NVF2518GSXCA 15 $392TENV 0.33 1800 208-230/460 SE na N 56C NVF3318GSXCA 15 $402TENV 0.33 1800 230/460 EE na N 56C NVF3318AEXCA $409TENV 0.33 1200 208-230/460 SE na N 56C NVF3312GSXCA 15 $530TENV 0.33 1200 230/460 EE na N 56C NVF3312AEXCA $544TENV 0.5 3600 208-230/460 SE na Yes 56C NV0F536GSXCA 15 $390TENV 0.5 3600 230/460 EE na N 56C NV0F536AEXCA $399TEFC 0.5 1800 208-230/460 SE na Yes 56C FC0F518GSXCA 15 $438TENV 0.5 1800 230/460 EE na N 56C NV0F518AEXCA $447TENV 0.5 1800 230/460 PE na N 143TC NV0F518APXCA 50 $739TEFC 0.5 1200 208-230/460 SE na Yes 56C FC0F512GSXCA 15 $567TENV 0.5 1200 230/460 EE na N 56C NV0F512AEXCA $576TENV 0.5 1200 230/460 PE na N 143TC NV0F512APXCA 50 $912TEFC 0.75 3600 208-230/460 SE na Yes 56C FCF7536GSXCA 15 $419TENV 0.75 3600 230/460 EE na N 56C NVF7536AEXCA $431TEFC 0.75 1800 208-230/460 SE na Yes 56C FCF7518GSXCA 15 $470TENV 0.75 1800 230/460 EE na N 56C NVF7518AEXCA $485TENV 0.75 1800 230/460 PE na N 143TC NVF7518APXCA 50 $785TEFC 0.75 1200 208-230/460 SE na Yes 56C FCF7512GSXCA 15 $581TENV 0.75 1200 230/460 EE na N 56C NVF7512AEXCA $592TEFC 0.75 1200 230/460 EE na N 143TC FCF7512AEXCA $592TENV 0.75 1200 230/460 PE na N 143TC NVF7512APXCA 50 $931


157

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 1 3600 208-230/460 SE na Yes 56C FC00136GSXCA 15 $453TEFC 1 3600 230/460 EE na N 56C FC00136AEXCA $463TENV 1 3600 230/460 PE na Yes 143TC NV00136APXCA 50 $778TENV 1 1800 208-230/460 SE na Yes 56C NV00118GSXCA 15 $477TEFC 1 1800 230/460 EE na N 56C FC00118AEXC5A $490TEFC 1 1800 230/460 EE na N 143TC FC00118AEXC4A $490TENV 1 1800 230/460 PE na Yes 143TC NV00118APXCA 50 $785TEFC 1 1200 208-230/460 SE na Yes 56C FC00112GSXCA 15 $612TEFC 1 1200 230/460 EE na N 56C FC00112AEXC5A $625TEFC 1 1200 230/460 EE na N 145TC FC00112AEXC4A $625TEFC 1 1200 230/460 PE na N 145TC FC00112APXCA 50 $976TEFC 1.5 3600 208-230/460 SE na Yes 56C FC1F536GSXCA 15 $518TEFC 1.5 3600 230/460 EE na N 56C FC1F536AEXC5A $528TEFC 1.5 3600 230/460 EE na N 143TC FC1F536AEXC4A $528TEFC 1.5 3600 230/460 PE na Yes 143TC FC1F536APXCA 50 $875TEFC 1.5 1800 208-230/460 SE na Yes 56C FC1F518GSXCA 15 $512TEFC 1.5 1800 230/460 EE na N 56C FC1F518AEXC5A $522TEFC 1.5 1800 230/460 EE na N 145TC FC1F518AEXC4A $522TEFC 1.5 1800 230/460 PE na Yes 145TC FC1F518APXCA 50 $847TEFC 1.5 1200 230/460 PE na N 182TC FC1F512APXCA $783TEFC 2 3600 230/460 EE na N 56C FC00236AEXC5A $585TEFC 2 3600 230/460 EE na N 145TC FC00236AEXC4A $585TEFC 2 3600 230/460 PE na Yes 145TC FC00236APXCA 50 $966TEFC 2 1800 230/460 EE na N 56C FC00218AEXC5A $507TEFC 2 1800 230/460 EE na N 145TC FC00218AEXC4A $507TEFC 2 1800 230/460 PE na Yes 145TC FC00218APXCA 50 $896TEFC 2 1200 230/460 PE na N L184TC FC00212APXCA $865TEFC 3 3600 230/460 PE na Yes 182TC FC00336APXCA $778TEFC 3 1800 230/460 PE na Yes 182TC FC00318APXCA $760TEFC 3 1200 230/460 PE na N 213TC FC00312APXCA $1,031TEFC 5 3600 230/460 PE na Yes 184TC FC00536APXCA $908TEFC 5 1800 230/460 PE na Yes L184TC FC00518APXCA $875TEFC 5 1200 230/460 PE na N L215TC FC00512APXCA $1,425TEFC 7.5 3600 230/460 PE na Yes 213TC FC7F536APXCA $1,157TEFC 7.5 1800 230/460 PE na Yes 213TC FC7F518APXCA $1,150TEFC 10 3600 230/460 PE na Yes 215TC FC01036APXCA $1,341TEFC 10 1800 230/460 PE na Yes L215TC FC01018APXCA $1,273TEFC 15 1800 460 PE na Yes 254TC FC01518BPXCA $1,744TEFC 15 1800 230/460 PE na Yes 254TC FC01518APXCA $1,744TEFC 20 1800 230/460 PE na Yes 256TC FC02018APXCA $2,060TEFC 20 1800 460 PE na Yes 256TC FC02018BPXCA $2,060TEFC 25 1800 460 PE na Yes 284TC FC02518BPXCA $2,646TEFC 25 1800 230/460 PE na Yes 284TC FC02518APXCA $2,646TEFC 30 1800 230/460 PE na Yes 286TC FC03018APXCA $3,061TEFC 30 1800 460 PE na Yes 286TC FC03018BPXCA $3,061TEFC 40 1800 230/460 PE na Yes 324TC FC04018APXCA $4,009



RPM Class Torque/Spd Stock PriceTENV 0.33 1800 208-230/460 SE na Yes 56C NVF3318GSXFA 15 $361TENV 0.33 1800 230/460 EE na Yes 56C NVF3318AEXFA $381TENV 0.33 1200 208-230/460 SE na Yes 56C NVF3312GSXFA 15 $494


158

General

Information

CM

100C

M 200

CM

300F

ootnotes


TENV 0.33 1200 230/460 EE na N 56C NVF3312AEXFA $506TENV 0.5 3600 208-230/460 SE na N 56C NV0F536GSXFA 15 $364TENV 0.5 3600 230/460 EE na N 56C NV0F536AEXFA $380TEFC 0.5 1800 208-230/460 SE na Yes 56C FC0F518GSXFA 15 $394TENV 0.5 1800 230/460 EE na Yes 56C NV0F518AEXFA $418TENV 0.5 1800 230/460 PE na N 143TC NV0F518APXFA 50 $700TEFC 0.5 1200 230/460 SE na N 56C FC0F512ASXFA $529TENV 0.5 1200 230/460 EE na N 56C NV0F512AEXFA $539TENV 0.5 1200 230/460 PE na N 143TC NV0F512APXFA 50 $867TEFC 0.75 3600 230/460 SE na N 56C FCF7536ASXFA $392TENV 0.75 3600 230/460 EE na N 56C NVF7536AEXFA $410TEFC 0.75 1800 208-230/460 SE na Yes 56C FCF7518GSXFA 15 $423TENV 0.75 1800 230/460 EE na Yes 56C NVF7518AEXFA $448TENV 0.75 1800 230/460 PE na Yes 143TC NVF7518APXFA 50 $744TEFC 0.75 1200 208-230/460 SE na Yes 56C FCF7512GSXFA 15 $541TENV 0.75 1200 230/460 EE na N 56C NVF7512AEXFA $555TEFC 0.75 1200 230/460 EE na N 143TC FCF7512AEXFA $555TENV 0.75 1200 230/460 PE na N 143TC NVF7512APXFA 50 $884TEFC 1 3600 208-230/460 SE na N 56C FC00136GSXFA 15 $424TEFC 1 3600 230/460 EE na N 56C FC00136AEXFA $445TENV 1 3600 230/460 PE na Yes 143TC NV00136APXFA 50 $738TENV 1 1800 208-230/460 SE na Yes 56C NV00118GSXFA 15 $430TEFC 1 1800 208-230/460 SE na Yes 143TC FC00118GSXFA 15 $430TEFC 1 1800 230/460 EE na Yes 56C FC00118AEXF5A $457TEFC 1 1800 230/460 EE na Yes 143TC FC00118AEXF4A $457TENV 1 1800 230/460 PE na Yes 143TC NV00118APXFA 50 $755TEFC 1 1200 208-230/460 SE na N 56C FC00112GSXFA 15 $570TEFC 1 1200 230/460 EE na N 56C FC00112AEXF5A $582TEFC 1 1200 230/460 EE na N 145TC FC00112AEXF4A $582TEFC 1 1200 230/460 PE na N 145TC FC00112APXFA 50 $927TEFC 1.5 3600 208-230/460 SE na N 56C FC1F536GSXFA 15 $486TEFC 1.5 3600 230/460 SE na N 143TC FC1F536ASXFA $486TEFC 1.5 3600 230/460 EE na N 56C FC1F536AEXF5A $512TEFC 1.5 3600 230/460 EE na N 143TC FC1F536AEXF4A $512TEFC 1.5 3600 230/460 PE na Yes 143TC FC1F536APXFA 50 $830TEFC 1.5 1800 208-230/460 SE na Yes 56C FC1F518GSXF5A 15 $461TEFC 1.5 1800 208-230/460 SE na Yes 145TC FC1F518GSXF4A 15 $461TEFC 1.5 1800 230/460 EE na Yes 56C FC1F518AEXF5A $474TEFC 1.5 1800 230/460 EE na Yes 145TC FC1F518AEXF4A $474TEFC 1.5 1800 230/460 PE na Yes 145TC FC1F518APXFA 50 $802TEFC 1.5 1200 230/460 PE na N 182TC FC1F512APXFA $811TEFC 2 3600 230/460 SE na N 56C FC00236ASXF5A $545TEFC 2 3600 230/460 SE na N 145TC FC00236ASXF4A $545TEFC 2 3600 230/460 EE na N 56C FC00236AEXF5A $574TEFC 2 3600 230/460 EE na N 145TC FC00236AEXF4A $574TEFC 2 3600 230/460 PE na Yes 145TC FC00236APXFA 50 $919TEFC 2 1800 208-230/460 SE na Yes 56C FC00218GSXF5A 15 $491TEFC 2 1800 208-230/460 SE na Yes 145TC FC00218GSXF4A 15 $491TEFC 2 1800 230/460 EE na N 56C FC00218AEXF5A $506TEFC 2 1800 230/460 EE na Yes 145TC FC00218AEXF4A $506TEFC 2 1800 230/460 PE na Yes 145TC FC00218APXFA 50 $850TEFC 2 1200 230/460 PE na N 184TC FC00212APXFA $893TEFC 3 3600 230/460 PE na N 182TC FC00336APXFA $807TEFC 3 1800 230/460 SE na Yes 145TC FC00318ASXFA $522TEFC 3 1800 230/460 PE na Yes 182TC FC00318APXFA $786TEFC 3 1200 230/460 PE na N 213TC FC00312APXFA $1,059TEFC 5 3600 230/460 PE na N 184TC FC00536APXFA $935TEFC 5 1800 230/460 PE na Yes 184TC FC00518APXFA $903TEFC 5 1200 230/460 PE na N 215TC FC00512APXFA $1,454


159

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 7.5 3600 230/460 PE na N 213TC FC7F536APXFA $1,185TEFC 7.5 1800 230/460 PE na Yes 213TC FC7F518APXFA $1,177TEFC 10 3600 230/460 PE na N 215TC FC01036APXFA $1,368TEFC 10 1800 230/460 PE na Yes 215TC FC01018APXFA $1,299TEFC 15 1800 460 PE na Yes 254TC FC01518BPXFA $1,816TEFC 15 1800 230/460 PE na Yes 254TC FC01518APXFA $1,816TEFC 20 1800 230/460 PE na Yes 256TC FC02018APXFA $2,121TEFC 20 1800 460 PE na Yes 256TC FC02018BPXFA $2,121TEFC 25 1800 230/460 PE na Yes 284TC FC02518APXFA $2,734TEFC 25 1800 460 PE na Yes 284TC FC02518BPXFA $2,734TEFC 30 1800 230/460 PE na Yes 286TC FC03018APXFA $3,149TEFC 30 1800 460 PE na Yes 286TC FC03018BPXFA $3,149



160

General

Information

CM

100C

M 200

CM

300F

ootnotes

General Information







112 Stainless steel T-drain 180-449 $618 103END BRACKET: Modify a foot mounted motor to include a C-Face end bracket.Note: Please add seal modification seperately if required.


Non-Nafta motors are non-NEMA BAGREASE FITTINGS: Install a grease fitting on each bearing.










440-L449 $589

charge will be invoiced to the customer. Any MOD order cancelled before modification is completed is subject to 25%


cancellation charge.

Changes to an Order


To cancel an order for a motor after it is modified, but before it ships - a cancellation charge of double the modification


161

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Modifications Available to CM311 MotorsSEALS: Addition of shaft seal.

148 Additon of V-ring rubber slinger on drive end 48-445 $251THERMAL PROTECTION: Addition of thermostats.



162

General

Information

CM

100C

M 200

CM

300F

ootnotes


Component ClassHarsh Environment SeriesCM312 Family - IEEE 841 AC Motors



Frequency: 60 Hz Duty Cycle: Continuous PE = Premium Efficient motors that exceed EPAct efficiency levels.Ambient: 40° C Insulation: Class F

Service Factor: 1.15 Temp. Rise: Class B NP = NEMA Premium efficient motors.

Warranty (From Date Of Manufacture /


Application InformationExceeds IEEE841 requirements, designed for long life and reliable operation in severe industrial applications. Built for durability in moist, contaminated, harsh environments such as chemical plants, petroleum reÞneries and paper mills.

PE & NP (60 / 48)


140T FramesMaterials: Cast iron frame, end shields, conduit box and fan coverConduit Box: F1 locationBearing Type: Double sealedBearing Protection: Inpro seals both endsShaft Material: Stainless SteelNameplate Material: Stainless SteelDrain Type & Location: T-drain in each end shield


gasketed cover, NPT threaded lead outlet, lead separator gasket to frame, UL listed clamp-type ground lug.

Bearing Type: Open ball PLS (Positive Lubrication System)Bearing Protection: Inpro seal each end plus cast iron inner caps inboardShaft Material: High strength carbon steelNameplate Material: Stainless SteelDrain Type & Location: Stainless steel T-drain in each end shieldAdditional Features: RTV sealed bracket-to-frame Þts, epoxy coated rotor and stator,

alemite grease Þttings, Gits cup grease relief Þttings, lead lugs, low vibration, and quiet operation (below 90 dBA sound power).


163

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Sine Wave Class, Harsh Environment SeriesCM312 Family - IEEE 841 AC Motors


RPM Class Torque/Spd Stock CM312- PriceTENV 0.5 1800 460 PE na N 143T NV0F518BPXHA $756TENV 0.5 1200 460 PE na N 143T NV0F512BPXHA $859TENV 0.75 1800 460 PE na N 143T NVF7518BPXHA $791TENV 0.75 1200 460 PE na N 143T NVF7512BPXHA $871TENV 1 3600 460 NP na yes 143T NV00136BNXHA $768TENV 1 1800 460 NP na yes 143T NV00118BNXHA $802TEFC 1 1200 460 NP na yes 182T FC00112BNXHA $822TEFC 1 900 460 PE na N L182T FC00109BPXHA $1,182TEFC 1.5 3600 460 NP na yes 143T FC1F536BNXHA $836TEFC 1.5 1800 460 NP na yes 145T FC1F518BNXHA $836TEFC 1.5 1200 460 NP na yes L182T FC1F512BNXHA $822TEFC 1.5 900 460 PE na N 182T FC1F509BPXHA $1,250TEFC 2 3600 460 NP na yes 145T FC00236BNXHA $761TEFC 2 1800 460 NP na yes 145T FC00218BNXHA $871TEFC 2 1200 460 NP na yes L184T FC00212BNXHA $870TEFC 2 900 460 PE na N L213T FC00209BPXHA $1,505TEFC 3 3600 460 NP na yes 182T FC00336BNXHA $881TEFC 3 1800 460 NP na yes L182T FC00318BNXHA $807TEFC 3 1200 460 NP na yes 213T FC00312BNXHA $1,048TEFC 3 900 460 PE na N L215T FC00309BPXHA $1,781TEFC 5 3600 460 NP na yes 184T FC00536BNXHA $957TEFC 5 1800 230/460 NP na yes L184T FC00518ANXHA 35 $877TEFC 5 1200 460 NP na yes L215T FC00512BNXHA $1,490TEFC 5 900 460 PE na N 254T FC00509BPXHA $2,728TEFC 7.5 3600 460 NP na yes 213T FC7F536BNXHA $1,195TEFC 7.5 1800 460 NP na yes L213T FC7F518BNXHA $1,123TEFC 7.5 1200 460 NP na yes 254T FC7F512BNXHA $2,127TEFC 7.5 900 460 PE na N 256T FC7F509BPXHA $3,373TEFC 10 3600 460 NP na yes 215T FC01036BNXHA $1,310TEFC 10 1800 460 NP na yes L215T FC01018BNXHA $1,201TEFC 10 1200 460 NP na yes 256T FC01012BNXHA $2,455TEFC 10 900 460 PE na N 284T FC01009BPXHA $4,159TEFC 15 3600 460 NP na yes 254T FC01536BNXHA $2,157TEFC 15 1800 460 NP na yes 254T FC01518BNXHA $2,004TEFC 15 1200 460 NP na yes 284T FC01512BNXHA $3,438TEFC 15 900 460 PE na N 286T FC01509BPXHA $5,033TEFC 20 3600 460 NP na yes 256T FC02036BNXHA $2,444TEFC 20 1800 460 NP na yes 256T FC02018BNXHA $2,264TEFC 20 1200 460 NP na yes 286T FC02012BNXHA $4,027TEFC 20 900 460 PE na N 324T FC02009BPXHA $6,246TEFC 25 3600 460 NP na yes 284TS FC02536BNXHA $3,245TEFC 25 1800 460 NP na yes 284T FC02518BNXHA $3,055TEFC 25 1200 460 NP na yes 324T FC02512BNXHA $5,094TEFC 25 900 460 PE na N 326T FC02509BPXHA $7,124TEFC 30 3600 460 NP na yes 286TS FC03036BNXHA $3,662TEFC 30 1800 460 NP na yes 286T FC03018BNXHA $3,438TEFC 30 1200 460 NP na yes 326T FC03012BNXHA $5,686TEFC 30 900 460 PE na N 364T FC03009BPXHA $8,343TEFC 40 3600 460 NP na yes 324TS FC04036BNXHA $4,785TEFC 40 1800 460 NP na yes 324T FC04018BNXHA $4,642TEFC 40 1200 460 NP na yes 364T FC04012BNXHA $7,600TEFC 40 900 460 PE na N 365T FC04009BPXHA $9,892TEFC 50 3600 460 NP na yes 326TS FC05036BNXHA $5,841TEFC 50 1800 460 NP na yes 326T FC05018BNXHTA $5,288TEFC 50 1800 460 NP na N 326TS FC05018BNXHSA $5,288TEFC 50 1200 460 NP na yes 365T FC05012BNXHA $8,665TEFC 50 900 460 PE na N 404T FC05009BPXHA $11,817


164

General

Information

CM

100C

M 200

CM

300F

ootnotes


TEFC 60 3600 460 NP na yes 364TS FC06036BNXHA $7,834TEFC 60 1800 460 NP na yes 364T FC06018BNXHTA $7,581TEFC 60 1800 460 NP na N 364TS FC06018BNXHSA $7,581TEFC 60 1200 460 NP na yes 404T FC06012BNXHA $10,118TEFC 60 900 460 PE na N 405T FC06009BPXHA $13,341TEFC 75 3600 460 NP na yes 365TS FC07536BNXHA $9,366TEFC 75 1800 460 NP na yes 365T FC07518BNXHTA $8,982TEFC 75 1800 460 NP na N 365TS FC07518BNXHSA $8,982TEFC 75 1200 460 NP na yes 405T FC07512BNXHA $11,112TEFC 75 900 460 PE na N 444T FC07509BPXHA $17,264TEFC 100 3600 460 NP na yes 405TS FC10036BNXHA $12,056TEFC 100 1800 460 NP na yes 405T FC10018BNXHTA $11,058TEFC 100 1800 460 NP na N 405TS FC10018BNXHSA $11,058TEFC 100 1200 460 NP na yes 444T FC10012BNXHA $14,302TEFC 100 900 460 PE na N 445T FC10009BPXHA $21,074TEFC 125 3600 460 NP na yes 444TS FC12536BNXHA $15,407TEFC 125 1800 460 NP na yes 444T FC12518BNXHTA $14,247TEFC 125 1800 460 NP na N 444TS FC12518BNXHSA $14,247TEFC 125 1200 460 NP na yes 445T FC12512BNXHA $17,040TEFC 125 900 460 PE na N 449T FC12509BPXHB $22,896TEFC 125 900 460 PE na N 449T FC12509BPXUA 5 $22,896TEFC 150 3600 460 NP na yes 445TS FC15036BNXHA $18,237TEFC 150 1800 460 NP na N 445TS FC15018BNXHSA $16,371TEFC 150 1800 460 NP na yes 445T FC15018BNXHTA $16,371TEFC 150 1200 460 NP na yes 447T FC15012BNXUA 5 $20,749TEFC 150 1200 460 NP na yes 447T FC15012BNXHB $20,749TEFC 150 900 460 PE na N 449T FC15009BPXHB $28,716TEFC 150 900 460 PE na N 449T FC15009BPXUA 5 $28,716TEFC 200 3600 460 NP na yes 445TS FC20036BNXHA $22,709TEFC 200 1800 460 NP na yes 447T FC20018BNXHB $20,183TEFC 200 1800 460 NP na yes 447T FC20018BNXUA 5 $20,183TEFC 200 1200 460 NP na yes 449T FC20012BNXUA 5 $23,079TEFC 200 1200 460 NP na yes 449T FC20012BNXHB $23,079TEFC 200 900 460 PE na N 449T FC20009BPXHA $29,066TEFC 250 3600 460 NP na yes 449TS FC25036BNXHA $28,705TEFC 250 1800 460 NP na yes 449T FC25018BNXUA 5 $23,416



RPM Class Torque/Spd Stock PriceTENV 1 3600 460 PE na yes FL143TC NV00136BPXCA $716TENV 1 1800 460 PE na yes FL143TC NV00118BPXCA $744TEFC 1.5 3600 460 PE na yes FL143TC FC1F536BPXCA $771TEFC 1.5 1800 460 PE na yes FL145TC FC1F518BPXCA $773TEFC 2 3600 460 PE na yes FL145TC FC00236BPXCA $824TEFC 2 1800 460 PE na yes FL145TC FC00218BPXCA $803TEFC 3 3600 460 PE na yes 182TC FC00336BPXCA $973TEFC 3 1800 460 PE na yes 182TC FC00318BPXCA $898TEFC 5 3600 460 PE na yes 184TC FC00536BPXCA $1,048TEFC 5 1800 460 PE na yes L184TC FC00518BPXCA $968TEFC 7.5 3600 460 PE na yes 213TC FC7F536BPXCA $1,287TEFC 7.5 1800 460 PE na yes 213TC FC7F518BPXCA $1,215TEFC 10 3600 460 PE na yes 215TC FC01036BPXCA $1,401TEFC 10 1800 460 PE na yes L215TC FC01018BPXCA $1,293TEFC 15 3600 460 PE na yes 254TC FC01536BPXCA $2,278TEFC 15 1800 460 PE na yes 254TC FC01518BPXCA $2,124


165

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 20 3600 460 PE na yes 256TC FC02036BPXCA $2,564TEFC 20 1800 460 PE na yes 256TC FC02018BPXCA $2,384TEFC 25 1800 460 PE na yes 284TC FC02518BPXCA $3,221TEFC 30 1800 460 PE na yes 286TC FC03018BPXCA $3,604TEFC 40 1800 460 PE na yes 324TC FC04018BPXCA $4,900TEFC 50 1800 460 PE na yes 326TC FC05018BPXCA $5,546TEFC 60 1800 460 PE na yes 364TC FC06018BPXCA $7,948TEFC 75 1800 460 PE na yes 365TC FC07518BPXCA $9,349



RPM Class Torque/Spd Stock PriceTENV 1 3600 460 PE na yes 143TC NV00136BPXFA $710TENV 1 1800 460 PE na yes 143TC NV00118BPXFA $738TEFC 1.5 3600 460 PE na yes 143TC FC1F536BPXFA $765TEFC 1.5 1800 460 PE na yes 145TC FC1F518BPXFA $768TEFC 2 3600 460 PE na yes 145TC FC00236BPXFA $818TEFC 2 1800 460 PE na yes 145TC FC00218BPXFA $798TEFC 3 3600 460 PE na yes 182TC FC00336BPXFA $995TEFC 3 1800 460 PE na yes 182TC FC00318BPXFA $920TEFC 5 3600 460 PE na yes 184TC FC00536BPXFA $1,070TEFC 5 1800 460 PE na yes L184TC FC00518BPXFA $990TEFC 7.5 3600 460 PE na yes 213TC FC7F536BPXFA $1,309TEFC 7.5 1800 460 PE na yes 213TC FC7F518BPXFA $1,236TEFC 10 3600 460 PE na yes 215TC FC01036BPXFA $1,423TEFC 10 1800 460 PE na yes 215TC FC01018BPXFA $1,314TEFC 15 3600 460 PE na yes 254TC FC01536BPXFA $2,329TEFC 15 1800 460 PE na yes 254TC FC01518BPXFA $2,176TEFC 20 3600 460 PE na yes 256TC FC02036BPXFA $2,616TEFC 20 1800 460 PE na yes 256TC FC02018BPXFA $2,436



166

General

Information

CM

100C

M 200

CM

300F

ootnotes








Note: Not available on L180-L210 frames 320-449 $376142 F-1 to W8 180-280 $251








The delivery cycle will be subject to the availability of stock motors and parts. The Modification Center is designed to process and ship units as quickly as possible; therefore, “Hold for Approval” and other similar conditions are not available on Modification Center orders. Typically, modifications will require 1 to 4 business days, once the order is entered. Orders for more than 5 units may require additional delivery time. The lead time shown on a Passport screen is for the base motor only, modifications will add to actual lead


167

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Component ClassHarsh Environment SeriesCM313 Family - Aggregate Duty AC Motors



Frequency: 60 Hz Duty Cycle: Continuous EE = Energy Efficient motors that meet EPAct efficienciesAmbient: 40° C Insulation: Class F



Application InformationDesigned with high starting torque and breakdown torque for heavily loaded conveyor and crusher applications. Includes severe duty mechanical features for longer life and durability in harsh environments..

EE (36 / 24)

Nameplate Agency Approvals:CE, CSA, IEEE45


gasketed, NPT threaded lead outletBearing Type: Open, PLSBearing Protection: V-ring slinger on both endsShaft Material: High strength carbon steelNameplate Material: Stainless SteelDrain Type & Location:

T-drain on drive end

Additional Features: All 405T frames and larger have Inpro type mechanical labrynth seals on the drive end.All frame sizes are suitable for vertical applications without the need for modiÞcation.All 405T frames and larger have roller bearings on the drive end.75 HP, 360 frame size and below are NEMA Design C.75 HP, 405T frame size and large are NEMA Design A.


168

General

Information

CM

100C

M 200

CM

300F

ootnotes

Sine Wave Class, Harsh Environment SeriesCM313 Family - Aggregate Duty AC Motors


RPM Class Torque/Spd Stock CM313- PriceTEFC 5 1800 230/460 EE na yes 184T FC00518AEXHA $969TEFC 7.5 1800 230/460 EE na yes 213T FC7F518AEXHA $1,217TEFC 10 1800 230/460 EE na yes 215T FC01018AEXHA $1,346TEFC 15 1800 230/460 EE na yes 254T FC01518AEXHA $1,896TEFC 20 1800 230/460 EE na yes 256T FC02018AEXHA $1,939TEFC 25 1800 230/460 EE na yes 284T FC02518AEXHA $2,488TEFC 30 1800 230/460 EE na yes 286T FC03018AEXHA $2,535TEFC 40 1800 230/460 EE na yes 324T FC04018AEXHA $3,926TEFC 50 1800 230/460 EE na yes 326T FC05018AEXHA $4,168TEFC 60 1800 230/460 EE na yes 364T FC06018AEXHA $4,817TEFC 75 1800 230/460 EE na yes 365T FC07518AEXHA $4,847TEFC 75 1200 460 EE na yes 405T FC07512BEXUA 5 $9,694TEFC 100 1800 460 EE na yes 405T FC10018BEXUA 5 $7,313TEFC 100 1200 460 EE na yes 444T FC10012BEXUA 5 $10,771TEFC 125 1800 460 EE na yes 444T FC12518BEXUA 5 $9,317TEFC 125 1200 460 EE na yes 445T FC12512BEXUA 5 $11,449TEFC 150 1800 460 EE na yes 445T FC15018BEXUA 5 $10,060TEFC 150 1200 460 EE na yes 447T FC15012BEXUA 5 $19,140TEFC 200 1800 460 EE na yes 447T FC20018BEXUA 5 $17,880TEFC 200 1200 460 EE na yes 447T FC20012BEXUA 5 $20,583TEFC 250 1800 460 EE na yes 447T FC25018BEXUA 5 $20,470TEFC 250 1200 460 EE na yes 449T FC25012BEXUA 5 $20,895TEFC 300 1800 460 EE na yes 449T FC30018BEXUA 5 $20,680TEFC 350 1800 460 EE na yes 449T FC35018BEXUA 5 $24,234



169

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es






CONNECTIONS: Final connect dual to single voltage.107 High Voltage Connection (price by frame size) 180-320 $188

END BRACKET: Modify a foot mounted motor to include a C-Face end bracket.Note: Please add seal modification seperately if required.

121 Changing from std. end to C-face with feet (Non-NEMA BA) 180-250 $493122 Changing from std. end to C-face with feet (NEMA BA) Non-Nafta motors are 280-360 $744









159 Mount a set of qty (3) normally closed thermostats 180-360 $493440-449 $618 107




170

General

Information

CM

100C

M 200

CM

300F

ootnotes


Sine Wave ClassHarsh Environment SeriesCM315 Family - Washdown Duty White Epoxy Coated AC Motors






(24 / 12)

Application InformationFor service in washdown applications subject to sanitary codes. BISSC certiÞcation standard on 180T - 256T frame sizes and optional on 56 - 145T frame sizes.


56 - 140T FramesMaterials: Rolled steel frame and fan cover, cast aluminum conduit box,

cast iron end shields.Conduit Box: Oversized, top mounted with F1 and F2 lead outlets.Bearing Type: Double sealed ball bearings.Bearing Protection: Lip seal on both ends and drive end shaft slinger.Shaft Material: 300 series stainless steel.Nameplate Material: Adhesive MylarDrain Type & Location: Automatic T-drains every 90 degrees.Additional Features: White epoxy paint.

180T - 256T FramesMaterials: Smooth cast iron frame and end shields. Steel conduit box and fan cover.Conduit Box: F1 location, diagonally split, rotatable in 90 degree increments.Bearing Type: Double sealedBearing Protection: Lip seal and slingerShaft Material: Carbon steelNameplate Material: Stainless steelDrain Type & Location: T-drainsAdditional Features: White epoxy paint.


171

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Sine Wave Class, Harsh Environment SeriesCM315 Family - Washdown Duty AC Motors


RPM Class Torque/Spd Stock CM315- PriceTENV 0.5 3600 230/460 EE na N 56 NV0F536AEXHA $377TEFC 0.5 1800 208-230/460 EE na yes 56 FC0F518GEXHA 15 $407TENV 0.5 1800 208-230/460 EE na yes 56 NV0F518GEXHA 15 $407TENV 0.75 3600 230/460 EE na N 56 NVF7536AEXHA $405TEFC 0.75 1800 208-230/460 EE na yes 56 FCF7518GEXHA 15 $427TENV 0.75 1800 208-230/460 EE na yes 56 NVF7518GEXHA 15 $427TENV 1 3600 230/460 EE na N 56 NV00136AEXHA $441TEFC 1 1800 230/460 PE na yes 143T FC00118APXHA $579TENV 1 1800 230/460 EE na N 56 NV00118AEXHA $446TEFC 1 1800 230/460 EE na yes 143T FC00118AEXHA 15 $446TENV 1 1800 208-230/460 EE na yes 143T NV00118GEXHA 15 $446TENV 1.5 3600 230/460 EE na N 56 NV1F536AEXH5A $511TENV 1.5 3600 230/460 EE na N 143T NV1F536AEXH4A $511TEFC 1.5 1800 230/460 PE na yes 145T FC1F518APXHA $635TENV 1.5 1800 230/460 EE na N 56 NV1F518AEXHA $489TEFC 1.5 1800 208-230/460 EE na yes 145T FC1F518GEXHA 15 $489TENV 1.5 1800 208-230/460 EE na yes 145T NV1F518GEXHA 15 $489TEFC 2 3600 230/460 EE na N 56 FC00236AEXH5A $621TEFC 2 3600 230/460 EE na N 145T FC00236AEXH4A $621TEFC 2 1800 230/461 PE na yes 145T FC00218APXHA $792TEFC 2 1800 230/460 EE na N 56 FC00218AEXHA $644TEFC 2 1800 208-230/460 EE na yes 145T FC00218GEXHA 15 $609TEFC 3 3600 230/460 EE na N 145T FC00336AEXHA $756TEFC 3 1800 230/460 PE na yes 182T FC00318APXHA $1,052TEFC 3 1800 230/460 EE na yes 184T FC00318AEXHA 51 $809TEFC 5 1800 230/460 PE na yes 184T FC00518APXHA $1,202TEFC 5 1800 230/460 EE na yes 184T FC00518AEXHA 51 $924TEFC 7.5 1800 230/460 PE na yes 213T FC7F518APXHA $1,502TEFC 7.5 1800 230/460 EE na yes 215T FC7F518AEXHA 51 $1,156TEFC 10 1800 230/460 PE na yes 215T FC01018APXHA $1,797TEFC 10 1800 230/460 EE na yes 215T FC01018AEXHA 51 $1,382



RPM Class Torque/Spd Stock PriceTENV 0.5 3600 208-230/460 EE na yes 56C NV0F536GEXCA 15 $380TEFC 0.5 1800 208-230/460 EE na yes 56C FC0F518GEXCA 15 $426TENV 0.5 1800 208-230/460 EE na yes 56C NV0F518GEXCA 15 $426TENV 0.5 1200 208-230/460 EE na N 56C NV0F512GEXCA 15 $500TENV 0.75 3600 208-230/460 EE na yes 56C NVF7536GEXCA 15 $417TEFC 0.75 1800 208-230/460 EE na yes 56C FCF7518GEXCA 15 $493TENV 0.75 1800 208-230/460 EE na yes 56C NVF7518GEXCA 15 $493TEFC 0.75 1200 208-230/460 EE na N 56C FCF7512GEXCA 15 $540TENV 1 3600 208-230/460 EE na yes 56C NV00136GEXCA 15 $488TEFC 1 1800 230/460 PE na yes 143TC FC00118APXCA $668TENV 1 1800 208-230/460 EE na yes 56C NV00118GEXC5A 15 $514TEFC 1 1800 208-230/460 EE na yes 143TC FC00118GEXCA 15 $514TENV 1 1800 208-230/460 EE na yes 143TC NV00118GEXC4A 15 $514TEFC 1 1200 208-230/460 EE na N 145TC FC00112GEXCA 15 $618


172

General

Information

CM

100C

M 200

CM

300F

ootnotes


TENV 1.5 3600 208-230/460 EE na yes 56C NV1F536GEXC5A 15 $540TENV 1.5 3600 208-230/460 EE na yes 143TC NV1F536GEXC4A 15 $540TEFC 1.5 1800 230/460 PE na yes 143TC FC1F518APXCA $697TENV 1.5 1800 208-230/460 EE na yes 56C NV1F518GEXC5A 15 $536TEFC 1.5 1800 208-230/460 EE na yes 145TC FC1F518GEXCA 15 $536TENV 1.5 1800 208-230/460 EE na yes 145TC NV1F518GEXC4A 15 $536TEFC 1.5 1200 208-230/460 EE na N 145TC FC1F512GEXCA 15 $630TEFC 2 3600 208-230/460 EE na yes 56C FC00236GEXC5A 15 $598TEFC 2 3600 208-230/460 EE na yes 145TC FC00236GEXC4A 15 $635TEFC 2 1800 230/460 PE na yes 145TC FC00218APXCA $862TEFC 2 1800 208-230/460 EE na yes 56C FC00218GEXC5A 15 $663TEFC 2 1800 208-230/460 EE na yes 145TC FC00218GEXC4A 15 $663TEFC 3 3600 208-230/460 EE na yes 145TC FC00336GEXCA 15 $781TEFC 3 3600 230/460 EE na yes 184TC FC00336AEXCA 51 $992TEFC 3 1800 230/460 PE na yes 182TC FC00318APXCA $1,139TEFC 3 1800 230/460 EE na yes 184TC FC00318AEXCA 51 $876TEFC 5 3600 230/460 EE na yes 184TC FC00536AEXCA 51 $1,098TEFC 5 1800 230/460 PE na yes 184TC FC00518APXCA $1,289TEFC 5 1800 230/460 EE na yes 184TC FC00518AEXCA 51 $992TEFC 7.5 3600 230/460 EE na yes 215TC FC7F536AEXCA 51 $1,363TEFC 7.5 1800 230/460 PE na yes 213TC FC7F518APXCA $1,636TEFC 7.5 1800 230/460 EE na yes 215TC FC7F518AEXCA 51 $1,258TEFC 10 3600 230/460 EE na yes 215TC FC01036AEXCA 51 $1,619TEFC 10 1800 230/460 PE na yes 215TC FC01018APXCA $1,857TEFC 10 1800 230/460 EE na yes 215TC FC01018AEXCA 51 $1,430TEFC 15 3600 230/460 EE na yes 256TC FC01536AEXCA 51 $2,651TEFC 15 1800 230/460 PE na yes 254TC FC01518APXCA $3,394TEFC 15 1800 230/460 EE na yes 256TC FC01518AEXCA 51 $2,611TEFC 20 3600 230/460 EE na yes 256TC FC02036AEXCA 51 $3,046TEFC 20 1800 230/460 PE na yes 256TC FC02018APXCA $3,938TEFC 20 1800 230/460 EE na yes 256TC FC02018AEXCA 51 $3,029



RPM Class Torque/Spd Stock PriceTENV 0.5 3600 208-230/460 EE na N 56C NV0F536GEXFA 15 $387TEFC 0.5 1800 208-230/460 EE na yes 56C FC0F518GEXFA 15 $414TENV 0.5 1800 208-230/460 EE na yes 56C NV0F518GEXFA 15 $414TENV 0.75 3600 208-230/460 EE na N 56C NVF7536GEXFA 15 $411TEFC 0.75 1800 208-230/460 EE na yes 56C FCF7518GEXFA 15 $479TENV 0.75 1800 208-230/460 EE na yes 56C NVF7518GEXFA 15 $479TENV 1 3600 208-230/460 EE na N 56C NV00136GEXFA 15 $483TEFC 1 1800 230/460 PE na yes 143TC FC00118APXFA $651TENV 1 1800 208-230/460 EE na yes 56C NV00118GEXFA 15 $512TEFC 1 1800 208-230/460 EE na yes 143TC FC00118GEXFA 15 $512TENV 1 1800 208-230/460 EE na yes 143TC NV00118GEXFA 15 $501TENV 1.5 3600 208-230/460 EE na N 56C NV1F536GEXF5A 15 $540TENV 1.5 3600 208-230/460 EE na N 143TC NV1F536GEXF4A 15 $540TEFC 1.5 1800 230/460 PE na yes 143TC FC1F518APXFA $693TENV 1.5 1800 208-230/460 EE na yes 56C NV1F518GEXF5A 15 $533TEFC 1.5 1800 208-230/460 EE na yes 145TC FC1F518GEXFA 15 $533TENV 1.5 1800 208-230/460 EE na yes 145TC NV1F518GEXF4A 15 $533TEFC 2 3600 208-230/460 EE na N 56C FC00236GEXF5A 15 $606TEFC 2 3600 208-230/460 EE na N 145TC FC00236GEXF4A 15 $606TEFC 2 1800 230/460 PE na yes 145TC FC00218APXFA $791TEFC 2 1800 208-230/460 EE na yes 56C FC00218GEXF5A 15 $608TEFC 2 1800 208-230/460 EE na yes 145TC FC00218GEXF4A 15 $608


173

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


TEFC 3 3600 208-230/460 EE na yes 56C FC00336GEXF5A 15 $612TEFC 3 3600 208-230/460 EE na N 145TC FC00336GEXF4A 15 $612TEFC 3 1800 208-230/460 EE na yes 145TC FC00318GEXFA 15 $659TEFC 3 1800 230/460 PE na yes 182TC FC00318APXFA $1,042TEFC 3 1800 230/460 EE na yes 184TC FC00318AEXFA 51,75 $802TEFC 5 1800 230/460 PE na yes 184TC FC00518APXFA $1,182TEFC 5 1800 230/460 EE na yes 184TC FC00518AEXFA 51 $909TEFC 7.5 1800 230/460 PE na yes 213TC FC7F518APXFA $1,500TEFC 7.5 1800 230/460 EE na yes 215TC FC7F518AEXFA 51 $1,154TEFC 10 1800 230/460 PE na yes 215TC FC01018APXFA $1,703TEFC 10 1800 230/460 EE na yes 215TC FC01018AEXFA 51 $1,310



174

General

Information

CM

100C

M 200

CM

300F

ootnotes





THERMAL PROTECTION: Addition of thermostats.159 Mount a set of qty (3) normally closed thermostats 56-140 $224

180-210 $561SPACE HEATERS:


440-L449 $589




175

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es


Sine Wave ClassHarsh Environment SeriesCM318 Family - Stainless Steel AC Motors






Application InformationFor use in severe applications where chemicals will degrade the motor surface.

EE (24 / 12)


56 - 140T FramesMaterials: Stainless steel frame, end shields, conduit box and fan coverConduit Box: Oversized, top mounted with F1 and F2 lead outlets, water tight

connectorBearing Type: Double sealed ball bearings.Bearing Protection: Stainless lip seal on both ends and drive end shaft slinger.Shaft Material: 300 series stainless steelNameplate Material: Stainless SteelDrain Type & Location:

Additional Features:Water tight connector for leads.

Stainless T-drains every 90 degrees.

"Paint free"

176

General

Information

CM

100C

M 200

CM

300F

ootnotes


Sine Wave Class, Harsh Environment SeriesCM318 Family - Stainless Steel AC Motors


RPM Class Torque/Spd Stock CM318- PriceTENV 0.5 1800 208-230/460 EE na N 56 NV0F518GEXHA 15 $618TENV 0.75 1800 208-230/460 EE na N 56 NVF7518GEXHA 15 $644TENV 1 1800 208-230/460 EE na N 143T NV00118GEXHA 15 $665TEFC 1.5 1800 208-230/460 EE na N 145T FC1F518GEXHA 15 $682TEFC 2 1800 208-230/460 EE na N 145T FC00218GEXHA 15 $856



RPM Class Torque/Spd Stock PriceTENV 0.5 3600 208-230/460 EE na N 56C NV0F536GEXCA 15 $586TENV 0.5 1800 208-230/460 EE na N 56C NV0F518GEXCA 15 $638TENV 0.75 3600 208-230/460 EE na N 56C NVF7536GEXCA 15 $610TENV 0.75 1800 208-230/460 EE na N 56C NVF7518GEXCA 15 $663TEFC 1 3600 208-230/460 EE na N 56C FC00136GEXCA 15 $679TENV 1 1800 208-230/460 EE na N 56C NV00118GEXC5A 15 $683TEFC 1 1800 208-230/460 EE na N 56C FC00118GEXCA 15 $683TENV 1 1800 208-230/460 EE na N 143TC NV00118GEXC4A 15 $684TEFC 1.5 3600 208-230/460 EE na N 56C FC1F536GEXC5A 15 $687TEFC 1.5 3600 208-230/460 EE na N 145TC FC1F536GEXC4A 15 $688TEFC 1.5 1800 208-230/460 EE na N 145TC FC1F518GEXC4A 15 $700TEFC 1.5 1800 208-230/460 EE na N 56C FC1F518GEXC5A 15 $701TEFC 2 3600 208-230/460 EE na N 56C FC00236GEXC5A 15 $864TEFC 2 3600 208-230/460 EE na N 145TC FC00236GEXC4A 15 $865TEFC 2 1800 208-230/460 EE na N 56C FC00218GEXC5A 15 $875TEFC 2 1800 208-230/460 EE na N 145TC FC00218GEXC4A 15 $876TEFC 3 3600 208-230/460 EE na N 145TC FC00336GEXCA 15 $1,063TEFC 3 1800 208-230/460 EE na N 145TC FC00318GEXCA 15 $990



RPM Class Torque/Spd Stock PriceTENV 0.5 3600 208-230/460 EE na N 56C NV0F536GEXFA 15 $571TENV 0.5 1800 208-230/460 EE na N 56C NV0F518GEXFA 15 $621TENV 0.75 3600 208-230/460 EE na N 56C NVF7536GEXFA 15 $595TENV 0.75 1800 208-230/460 EE na N 56C NVF7518GEXFA 15 $647TEFC 1 3600 208-230/460 EE na N 56C FC00136GEXFA 15 $663TENV 1 1800 208-230/460 EE na N 56C NV00118GEXF5A 15 $667TENV 1 1800 208-230/460 EE na N 143TC NV00118GEXF4A 15 $668TEFC 1.5 3600 208-230/460 EE na N 145TC FC1F536GEXFA 15 $672TEFC 1.5 1800 208-230/460 EE na N 145TC FC1F518GEXFA 15 $686TEFC 2 3600 208-230/460 EE na N 145TC FC00236GEXFA 15 $849TEFC 2 1800 208-230/460 EE na N 145TC FC00218GEXFA 15 $860TEFC 3 3600 208-230/460 EE na N 145TC FC00336GEXFA 15 $1,048TEFC 3 1800 208-230/460 EE na N 145TC FC00318GEXFA 15 $964


177

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es




Delivery Cycle



No Modifications available for Stainless Steel Motors



178

General

Information

CM

100C

M 200

CM

300F

ootnotes



Footnotes

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

Footnotes1 F-1 mounting2 1.0 Service Factor3 Not suitable for use on motors with model number with a, b, or c suffixes4 Wye start, Delta run5 Belted duty only, roller bearing6 F-2 mounting7 Companion voltages not available8 TENV motors are capable of 20:1 speed range operation on drives with no back diode.9 Motors are not NAFTA qualified


11 Price includes XT features and explosion proof prices include drain on drive end12 Does not meet NEMA BA for C-Face Footed Motors13 Furnished without conduit box. Order kit P/N K56G323014 Type CH15 Motors rated 208 - 230/460 are operable to minimum 200 volts16 Standard TENV motor with standard lead length17 Class B insulation, 1.0 service factor18 Class B insulation, 1.25 service factor19 Class B insulation, 1.35 service factor20 Class F insulation21 Double bolt22 Base used for NEMA & above NEMA frames, 445T23 Two piece slide rails24 Includes terminal board25 Production only after stock depleted. To be superseded by V*S Master Motor26 See OMS27 Kits include textile fan cover with drip cover mounted. Suitable for TEFC or TEFC-XT foot and footless design only

(not XP or O28 5.5 inch frame - Aluminum end shield standard enclosure29 6.3 inch frame - Aluminum end shield standard enclosure30 Motors usable on 208 volts @ specified amps31 Suitable for 230/460, 60Hz and 190-220/380-440 volts, 50Hz32 Stearns brake33 Reliance AC brake34 Dodge D series brake35 Design A, also meets Design E inrush limits36 1.0 Service factor when operated at 50Hz37 Derate horsepower 20% when operated at 50hz38 Consists of sleeve and key to convert 1/2 shaft to 5/8 shaft39 Coupled Duty only, TS shaft40 Includes tachometer, stab shaft and mounting hardware41 Will mount any tachometer having standard NEMA 56 C-face and shaft extension42 DODGE Short Series Brake43 Cannot be mounted vertically44 Scrambler drive - DC integrated control and motor product45 Maximum value46 No key - 1.25 long flat47 BA dimension does not meet NEMA standards48 Includes phase insulation. Suitable for inverter duty49 Includes vertical lifting provision50 Cast Iron 140 Frame51 BISSC certified53 Mounting hole diameter


179

Gen

eral

Info

rmat

ion

CM

100

CM

200

CM

300

Foo

tnot

es

54 For single phase ratings: O = 7.31: Z = 12.8055 Refer to previous dimension pages56 48 through 140T frame ratings are typical full load efficiency, not nominal efficiency57 56 through 140T frame performance data is valid for TENV or TEFC. 180T and larger frame performance data is

valid for TEFC ONLY59 FLA includes harmonic content from PWM power supply61 TENV motors have a constant torque speed range from 0 to base speed62 TENV motors have provisions for tachometer mounting as standard65 Will fit standard efficient F model numbers ONLY71 Nominal efficiency is base at the 1800 RPM (High RPM) and low speed efficiency is available just not

published72 Orders shipped from a Rockwell Automation facility in 5 working days. Motor is returnable for a restocking charge

of $100 plus 73 Can only be used on motors 1800 RPM and slower with ball bearings75 Availability limited to current stock

79 Motor mounted blower is located on drive end80 Motor has thermostat and provisions for adding flange mtd. tach81 Motor has thermostat and provisions for adding adapter mtd. tach82 Motor is force ventilated and supplied with blower, and filter.83 May be operated on 50 Hz rectified power supply with full nameplate rating. AC supply voltage must be same as

60 Hz supply; i.e84 May be operated on 50 Hz rectified power supply with full nameplate rating only when motor is force ventilated

with motor mount85 Cannot be operated at full nameplate rating on 50 Hz rectified power supply86 Winder Duty - 100% load for 1 minute at 3000 RPM, straight shunt design. Includes blower without filter.

Tachometer is rated at87 Motor has thermostat and provision for adding integral AC or DC tachometer or adapter mounted tachometer.88 Motor is force ventilated and supplied with blower.89 Motor is force ventilated and supplied with single-phase blower motor rated 1/3 HP, 3450/2850 RPM, 115/230

volts, 60/50 Hz.90 Includes thermostat91 Includes Dynapar H20 1024 PPR encoder with mating 10 pin MS connector. Requires 2-7 business days.92 Blower is piggyback mounted on L440 frames93 180TC NEMA flange size, see appropriate dimension sheet.94 210TC NEMA flange size, see appropriate dimension sheet95 250TC NEMA flange size, see appropriate dimension sheet96 See appropriate dimension sheet for flange size99 Highlighted for Marketing Review

100 Ball bearing only101 Not available for Easy Clean product line102 Not available for XT enclosures103 Not available for Non-NAFTA motors104 Not available for 841 XL motors105 Not available on SABRE and CALIBRE product lines106 Finned aluminum frame construction107 Not available on belted duty motors and/or motors with roller bearings121 Motor is rated for F rise 1000:1 Constant Torque Range, and F Rise 4:1 Constant Torque Range122 Motor rated for only F rise 4:1 Constant Torque Range




180

General

Information

CM

100C

M 200

CM

300F

ootnotes

NOTES

1 F-1 mounting

2 1.0 Service Factor

3 Not suitable for use on motors with model number with a, b, or c suffi xes

4 Wye start, Delta run

5 Belted duty only, roller bearing

6 F-2 mounting

7 Companion voltages not available

8 TENV motors are capable of 20:1 speed range operation on drives with no back diode.

9 Motors are not NAFTA qualifi ed


11 Price includes XT features and explosion proof prices include drain on drive end

12 Does not meet NEMA BA for C-Face Footed Motors

13 Furnished without conduit box. Order kit P/N K56G3230

14 Type CH

15 Motors rated 208 - 230/460 are operable to minimum 200 volts

16 Standard TENV motor with standard lead length




20 Class F insulation

21 Double bolt

22 Base used for NEMA & above NEMA frames, 445T

23 Two piece slide rails

24 Includes terminal board

25 Production only after stock depleted. To be superseded by V*S Master Motor

26 See OMS

27 Kits include textile fan cover with drip cover mounted. Suitable for TEFC or TEFC-XT foot and footless design only (not XP or O



30 Motors usable on 208 volts @ specifi ed amps

31 Suitable for 230/460, 60Hz and 190-220/380-440 volts, 50Hz

32 Stearns brake

33 Reliance AC brake

34 Dodge D series brake

35 Design A, also meets Design E inrush limits

36 1.0 Service factor when operated at 50Hz

37 Derate horsepower 20% when operated at 50hz

38 Consists of sleeve and key to convert 1/2 shaft to 5/8 shaft

39 Coupled Duty only, TS shaft

40 Includes tachometer, stab shaft and mounting hardware

41 Will mount any tachometer having standard NEMA 56 C-face and shaft extension

42 DODGE Short Series Brake

43 Cannot be mounted vertically

44 Scrambler drive - DC integrated control and motor product

45 Maximum value

46 No key - 1.25 long fl at

47 BA dimension does not meet NEMA standards

48 Includes phase insulation. Suitable for inverter duty

49 Includes vertical lifting provision

50 Cast Iron 140 Frame

51 BISSC certifi ed

53 Mounting hole diameter

54 For single phase ratings: O = 7.31: Z = 12.80

55 Refer to previous dimension pages

56 48 through 140T frame ratings are typical full load effi ciency, not nominal effi ciency

57 56 through 140T frame performance data is valid for TENV or TEFC. 180T and larger frame performance data is valid for TEFC ONLY

59 FLA includes harmonic content from PWM power supply

61 TENV motors have a constant torque speed range from 0 to base speed

62 TENV motors have provisions for tachometer mounting as standard

65 Will fi t standard effi cient F model numbers ONLY

71 Nominal effi ciency is base at the 1800 RPM (High RPM) and low speed effi ciency is available just not published

72 Orders shipped from a Rockwell Automation facility in 5 working days. Motor is returnable for a restocking charge of $100 plus

73 Can only be used on motors 1800 RPM and slower with ball bearings

75 Availability limited to current stock


79 Motor mounted blower is located on drive end

80 Motor has thermostat and provisions for adding fl ange mtd. tach

81 Motor has thermostat and provisions for adding adapter mtd. tach

82 Motor is force ventilated and supplied with blower, and fi lter.

83 May be operated on 50 Hz rectifi ed power supply with full nameplate rating. AC supply voltage must be same as 60 Hz supply; i.e

84 May be operated on 50 Hz rectifi ed power supply with full nameplate rating only when motor is force ventilated with motor mount

85 Cannot be operated at full nameplate rating on 50 Hz rectifi ed power supply

86 Winder Duty - 100% load for 1 minute at 3000 RPM, straight shunt design. Includes blower without fi lter. Tachometer is rated at

87 Motor has thermostat and provision for adding integral AC or DC tachometer or adapter mounted tachometer.

88 Motor is force ventilated and supplied with blower.

89 Motor is force ventilated and supplied with single-phase blower motor rated 1/3 HP, 3450/2850 RPM, 115/230 volts, 60/50 Hz.

90 Includes thermostat

91 Includes Dynapar H20 1024 PPR encoder with mating 10 pin MS connector. Requires 2-7 business days.

92 Blower is piggyback mounted on L440 frames

93 180TC NEMA fl ange size, see appropriate dimension sheet.



96 See appropriate dimension sheet for fl ange size

99 Highlighted for Marketing Review

100 Ball bearing only

101 Not available for Easy Clean product line

102 Not available for XT enclosures

103 Not available for Non-NAFTA motors

104 Not available for 841 XL motors

105 Not available on SABRE and CALIBRE product lines

106 Finned aluminum frame construction

107 Not available on belted duty motors and/or motors with roller bearings

121 Motor is rated for F rise 1000:1 Constant Torque Range, and F Rise 4:1 Constant Torque Range

122 Motor rated for only F rise 4:1 Constant Torque Range


Vers

ion

Vers

ion

Not

e- C

ontro

lled

by P

assp

ort

See

Vers

ion

Not

es fo

r Rev

isio

n Ch

ange

s

Bul

letin

CM10

0Co

mpo

nent

Cla

ss -

Inve

rter D

uty

CM20

0Ar

chite

ctur

e Cl

ass

- Vec

tor D

uty

CM30

0Si

ne W

ave

Clas

s

Encl

osur

e

DGDP

G - D

rip-P

roof

Gua

rded

FVDP

G-FV

- Dr

ip-P

roof

Gua

rded

For

ce V

entil

ated

DPOD

P - O

pen

Drip

-Pro

of

AOTE

AO -

Tota

lly E

nclo

sed

Air O

ver

BCTE

BC -

Tota

lly E

nclo

sed

Blow

er C

oole

d

FCTE

FC -

Tota

lly E

nclo

sed

Fan

Cool

ed

NV

TEN

V - T

otal

ly E

nclo

sed

Non

Ven

tilat

ed

AATE

DC A

/A -

Tota

lly E

nclo

sed

Dual

Coo

led

Air t

o Ai

r

AWTE

DC A

/W -

Tota

lly E

nclo

sed

Dual

Coo

led

Air t

o W

ater

Bul

letin

Encl

osur

e

Hor

sepo

wer

Bas

e Sp

eed

V

olta

ge

Ef

fi cie

ncy

C

T or

VT

Requ

ired

Mou

ntin

g

Fin

al D

escr

ipto

r

Ver

sion

Alle

n-B

radl

ey C

ontr

ol M

atch

ed M

otor

s Ca

talo

g St

ring

Dec

oder

Hor

sepo

wer

HP a

s lis

ted

025

25 H

orse

pow

er

Not

e “F

” is

use

d fo

r a d

ecim

al p

oint

030

30 H

orse

pow

er

F17

0.17

Hor

sepo

wer

040

40 H

orse

pow

er

F25

0.25

Hor

sepo

wer

050

50 H

orse

pow

er

F33

0.33

Hor

sepo

wer

060

60 H

orse

pow

er

0F5

0.5

Hors

epow

er07

575

Hor

sepo

wer

F75

0.75

Hor

sepo

wer

100

100

Hors

epow

er

001

1 Ho

rsep

ower

125

125

Hors

epow

er

1F5

1.5

Hors

epow

er15

015

0 Ho

rsep

ower

002

2 Ho

rsep

ower

200

200

Hors

epow

er

003

3 Ho

rsep

ower

250

250

Hors

epow

er

005

5 Ho

rsep

ower

300

300

Hors

epow

er

7F5

7.5

Hors

epow

er35

035

0 Ho

rsep

ower

010

10 H

orse

pow

er40

040

0 Ho

rsep

ower

015

15 H

orse

pow

er45

045

0 Ho

rsep

ower

020

20 H

orse

pow

er50

050

0 Ho

rsep

ower

1K0

1000

Hor

sepo

wer

Bas

e Sp

eed

As n

oted

- fi r

st tw

o di

gits

of b

ase

spee

d

0550

0 RP

M12

1200

RPM

0665

0 RP

M15

1500

RPM

0772

0 RP

M17

1750

RPM

0885

0 RP

M18

1800

RPM

0990

0 RP

M25

2500

RPM

1010

00 R

PM35

3550

RPM

1111

50 R

PM36

3600

RPM

Volta

ge

F23

0 Vo

lt, 3

Pha

se, 6

0 Hz

L18

0 V

Arm

, 100

/200

V F

ield

, Str

Win

ding

D38

0 Vo

lt, 3

Pha

se, 5

0 Hz

M24

0 V

Arm

, 150

V F

ield

, Str

Win

ding

E40

0 Vo

lt, 3

Pha

se, 5

0 Hz

N24

0 V

Arm

, 240

V F

ield

, Str

Win

ding

B46

0 Vo

lt, 3

Pha

se, 6

0 Hz

Q50

0 V

Arm

, 300

V F

ield

, Str

Win

ding

C57

5 Vo

lt, 3

Pha

se, 6

0 Hz

P50

0 V

Arm

, 150

/300

V F

ield

, Sta

b W

indi

ng

R23

00 V

olt,

3 Ph

ase,

60

HzT

240

V Ar

m, 1

50 V

Fie

ld, S

tab

Win

ding

S41

60 V

olt,

3 Ph

ase,

60

HzU

240

V Ar

m, 2

40 V

Fie

ld, S

tab

Win

ding

H20

0/20

8 Vo

lt, 3

Pha

se, 6

0 Hz

V50

0 V

Arm

, 300

V F

ield

, Sta

b W

indi

ng

G20

8-23

0/46

0 Vo

lt, 3

Pha

se, 6

0 Hz

W90

V A

rm, P

M F

ield

A23

0/46

0 Vo

lt, 3

Pha

se, 6

0 Hz

J18

0 V

Arm

, PM

Fie

ld

K90

V A

rm, 5

0/10

0 V

Fiel

d

Effi c

ienc

y

EEn

ergy

Effi

cien

t - M

eets

EPA

ct R

equi

rem

ents

SSt

anda

rd E

ffi ci

ent

NN

EMA

Prem

ium

PPr

emiu

m E

ffi ci

ent

XN

ot A

pplic

able

CT o

r VT

requ

ired

HCT

10:

1Co

nsta

nt To

rque

10:

1 Sp

eed

Rang

e

ZCT

100

0:1

Cons

tant

Torq

ue 1

000:

1 Sp

eed

Rang

e (0

to B

ase

Spee

d)

JCT

2:1

Cons

tant

Torq

ue 2

:1 S

peed

Ran

ge

JCT

2:1

(10)

Cons

tant

Torq

ue 2

:1 S

peed

Ran

ge (c

apab

le o

f 10:

1 CT

with

fan

chan

ge)

MCT

20:

1Co

nsta

nt To

rque

20:

1 Sp

eed

Rang

e

KCT

4:1

Cons

tant

Torq

ue 4

:1 S

peed

Ran

ge

KCT

4:1

(10)

Cons

tant

Torq

ue 4

:1 S

peed

Ran

ge (c

apab

le o

f 10:

1 CT

with

fan

chan

ge)

Xna

Not

for u

se o

n in

verte

r pow

er

VVT

10:

1Va

riabl

e To

rque

10:

1 Sp

eed

Rang

e

VVT

10:

1 (2

)Va

riabl

e To

rque

10:

1 Sp

eed

Rang

e (c

apab

le o

f 2:1

CT

with

fan

chan

ge)

Mou

ntin

g

CC-

Face

Foo

t Mou

nted

FC-

Face

Foo

tless

HFo

ot M

ount

ed

UFo

ot M

ount

ed, R

olle

r Bea

ring

Fina

l Dis

crip

tor

414

0 Fr

ame

Mot

or

556

Fra

me

Mot

or

818

0 Fr

ame

Mot

or

ICa

st ir

on F

ram

e

NN

on-c

ast i

ron

fram

e

STS

sha

ft le

ngth

TN

ema

T sh

aft l

engt

h

This

tool

sho

uld

ON

LY b

e us

ed to

DEC

OD

E ex

istin

g ca

talo

g st

ring

s.

It CA

NN

OT

be u

sed

to c

reat

e a

new

par

t num

ber.

Allen-Bradley offers the broadest selection of drive and motor packages designed for optimum variable-speed performance, service life and value. These Control-Matched drive and motor packages are a result of the practi-cal application of advanced electrical/electronic technology – backed by decades of application experience in virtually every industry. For additional information refer to our web site: www.controlmatched.com

Control-MatchedTM

Drives and MotorsFor Optimum Variable-Speed Value

www.rockwellautomation.com

Corporate HeadquartersRockwell Automation, 777 East Wisconsin Avenue, Suite 1400, Milwaukee, WI, 53202-5302 USA, Tel: (1) 414.212.5200, Fax: (1) 414.212.5201

Headquarters for Dodge and Reliance Electric ProductsAmericas: Rockwell Automation, 6040 Ponders Court, Greenville, SC 29615-4617 USA, Tel: (1) 864.297.4800, Fax: (1) 864.281.2433Europe/Middle East/Africa: Rockwell Automation, Herman-Heinrich-Gossen-Strasse 3, 50858 Köln, Germany, Tel: 49 (0) 2234 37941252, Fax: 49 (0) 2234 3794164Asia Pacifi c: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong, Tel: (852) 2887.4788, Fax: (852) 2508.1846

Headquarters for Allen-Bradley Products, Rockwell Software Products and Global Manufacturing SolutionsAmericas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414.382.2000, Fax: (1) 414.382.4444Europe/Middle East/Africa: Rockwell Automation SA/NV, Vorstlaan/Boulevard du Souverain 36, 1170 Brussels, Belgium, Tel: (32) 2 663 0600, Fax: (32) 2 663 0640Asia Pacifi c: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong, Tel: (852) 2887 4788, Fax: (852) 2508 1846

This material is not intended to provide operational instructions. Appropriate Rockwell Automation instruction manuals and precautions should be studied prior to installation, operation or maintenance of equipment.

Copyright © 2005 Rockwell Automation, Inc. All rights reserved. Printed in USA.

RAPS-1348 3/05-7.5M-K

Allen-Bradley

Control Matched

Motor Catalog

Allen

-Bradley C

ontrol M

atched M

otor Catalog

M

arch 2005

control-matched drives and motors allen-bradley … scrambler drive - dc integrated ... 59 fla...

Documents