conversionatx a fuente

13
How to Convert a Computer ATX Power Supply to a Lab Power Supply Computer power supplies cost around US$15,but lab power supplies can run you $100 or more! By converting the cheap (free) ATX power supplies that can be found in any discarded computer, you can get a phenomenal lab power supply with huge current outputs, short circuit protection, and very tight voltage regulation. 1. Unplug the power cord from the back of the computer. "Harvest" a power supply from a computer by opening up the case of the computer, locating the gray box that is the power supply unit, tracing the wires from the power supply to the boards and devices and disconnecting all the cables by unplugging them. 2. Remove the screws (typically 4) that attach the power supply to the computer case and remove the power supply. 3. Cut off the connectors (leave a few inches of wire on the connectors so that you can use them later on for other projects). 4. Discharge the power supply by either letting it sit unconnected for a few days, or by attaching a 10 ohm resistor between a black and red wire (from the power cables on the output side). Using a resistor will only take a few seconds to fully discharge the power supply. 5. Gather the parts you need: binding posts (terminals), a LED with a current-limiting resistor, a switch (optional), a power resistor (10 ohm, 10W or greater wattage, see Tips), and heat shrink tubing. 6. Open up the power supply unit by removing the screws connecting the top and the bottom of the PSU case.

Upload: migueldelbarrioiglesisas

Post on 27-Nov-2015

2 views

Category:

Documents


0 download

TRANSCRIPT

How to Convert a Computer ATX Power Supply to aLab Power SupplyComputer power supplies cost around US$15,but lab power supplies can run you $100 or more! By converting the cheap (free) ATX powersupplies that can be found in any discarded computer, you can get a phenomenal lab power supply with huge current outputs, short circuitprotection, and very tight voltage regulation.

1. Unplug the power cord from the back of the computer. "Harvest" a power supply from a computer by opening up the case of the computer,locating the gray box that is the power supply unit, tracing the wires from the power supply to the boards and devices and disconnecting allthe cables by unplugging them.

2. Remove the screws (typically 4) that attach the power supply to the computer case and remove the power supply.

3. Cut off the connectors (leave a few inches of wire on the connectors so that you can use them later on for other projects).

4. Discharge the power supply by either letting it sit unconnected for a few days, or by attaching a 10 ohm resistor between a black and red wire(from the power cables on the output side). Using a resistor will only take a few seconds to fully discharge the power supply.

5. Gather the parts you need: binding posts (terminals), a LED with a current-limiting resistor, a switch (optional), a power resistor (10 ohm,10W or greater wattage, see Tips), and heat shrink tubing.6. Open up the power supply unit by removing the screws connecting the top and the bottom of the PSU case.

7. Bundle wires of the same colors together. If you have wires not listed here (brown, etc), see the Tips.The color code for the wires is: Red = +5V, Black = Ground (0V), White = -5V, Yellow = +12V, Blue = -12V, Orange = +3.3V, Purple = +5VStandby (not used), Gray = power is on (output), and Green = Turn DC on (input).

8. Drill holes in a free area of the power supply case by marking the center of the holes with a nail and a tap from the hammer. Use a Dremel todrill the starting holes followed by a hand reamer to enlarge the holes until they are the right size by test fitting the binding posts. Also, drillholes for the power ON LED and a Power switch (optional).

9. Screw the binding posts into their corresponding holes and attach the nut on the back.

10. Connect all the pieces together._ Connect one of the red wires to the power resistor, all the remaining red wires to the red binding posts;_ Connect one of the black wires to the other end of the power resistor, one black wire to a resistor (330 ohm) attached anode of the LED,one black wire to the DC-On switch, all the remaining black wires to the black binding post;_ Connect the white to the -5V binding post, yellow to the +12V binding post, the blue to the -12V binding post, the gray to the cathode ofthe LED;_ Note that some power supplies may have either a gray or brown wire to represent "power good"/"power ok". This wire should beconnected to either an orange wire (+3.3V) or a red wire (+5V) for the power supply to function. When in doubt, try the lower voltage first(+3.3V). If a power supply is non ATX or AT compliant, it may have its own color scheme. If yours looks different that the pictures shownhere, make sure you reference the position of the wires attached to the AT/ATX connector rather than the colors.1._ Connect the green wire to the other terminal on the switch._ Make sure that the soldered ends are insulated in heatshrink tubing._ Organize the wires with a electrical tape or zip-ties.

1. Check for loose connections by gently tugging on them. Inspect for bare wire, and cover it to prevent a short circuit. Put a drop of super-glueto stick the LED to its hole. Put the cover back on.

2. Plug the power cord into the back and into an AC socket. Flip the main switch on the PSU. Check to see if the LED light comes on. If it hasnot, then power up by flipping the switch you placed on the front. Plug in a 12V bulb into the different sockets to see if the PSU works, alsocheck with a digital voltmeter. It should look good and work like a charm!_ Options: You don't need an additional switch, just connect the green and a black wire together. The PSU will be controlled by the rear switch,if there is one. You also don't need an LED, just ignore the gray wire. Cut it short and insulate it from the rest._ Some newer power supplies will have "voltage sense" wires that need to be connected to the actual voltage wires for proper operation. In themain power bundle (the one with 20 wires), you should have four red wires and three orange wires. If you only have two orange wires, youshould also have a brown wire which must be connected with the orange. If you only have three red wires, another wire (sometimes pink)must be connected to them.

_ If the power supply does not work, that is, no LED light, check to see if the fan has come on. If the fan in the power supply is on, then theLED may have been wired wrong (the positive and negative leads of the LED may have been switched). Open the power supply case andflip the purple or gray wires on the LED around (make sure that you do not bypass the LED resistor)._ If you are not sure of the power supply, test it in the computer before you harvest. Does the computer power on? Does the PSU fan comeon? You can place your voltmeter leads into an extra plug (for disk drives). It should read close to 5V (between red and black wires). Asupply that you have pulled may look dead because it does not have a load on its outputs and the enable output may not be grounded (greenwire)._ ATX power supplies are "switch-mode supplies"; they must always have some load to operate properly. The power resistor is there to"waste" energy, which will give off heat; therefore it should be mounted on the metal wall for proper cooling. If you will always havesomething connected to the supply when it is on, you may leave out the power resistor._ Feel free to add some pizazz to the dull gray box._ You can also convert this to a variable power supply - but that is another article (hint: Uses a 317 IC with power transistor)._ The voltages that can be output by this unit are 24v (+12, -12), 17v (+5, -12), 12v (+12, 0), 10v (+5, -5), 7v (+12, +5), 5v (+5, 0) which shouldbe sufficient for most electrical testing. Many ATX power supplies with a 24-pin connector for motherboards will not supply the -5V lead. Lookfor ATX power supplies with a 20-pin connector, a 20+4-pin connector, or an AT power supply if you need -5V._ You can add a 3.3 volt output to the supply by hooking the orange wires to a post (making sure the brown wire remains connected to theorange bundle) but beware that they share the same power output as the 5 volt, and thus you must not exceed the total power output ofthese two outputs._ To get more room you can mount the fan on the outside of the PSU case_ If you don't feel like soldering nine wires together to a binding post (as is the case with the ground wires) you can snip them at the PCB. 1-3wires should be fine. This includes cutting any wires that you don't ever plan on using._ The +5VSB line is +5V standby (so the motherboard's power buttons, Wake on LAN, etc. work). This typically provides 500-1000 mA ofcurrent, even when the main DC outputs are "off". It might be useful to drive an LED from this as an indication that the mains is on.

Cómo convertir una fuente de alimentación ATX de ordenador a unLab Power Supply

Fuentes de alimentación de ordenador cuesta alrededor de EE.UU. $ 15, pero las fuentes de alimentación de laboratorio pueden costará $ 100 o más! Mediante la conversión de la energía ATX barato (gratis )suministros que se pueden encontrar en cualquier equipo descartado, usted puede obtener una fuente de alimentación de laboratorio fenomenal con enormes salidas de corriente de corto circuitoprotección y regulación de tensión muy fuerte .

1 . Desconecte el cable de alimentación de la parte posterior del equipo . " Harvest ", una fuente de alimentación de un ordenador al abrir la carcasa del ordenador ,la localización de la caja gris que es la fuente de alimentación , la localización de los cables de la red eléctrica a las juntas y los dispositivos y desconectar todos loslos cables , desenchufe ellos .

2 . Quite los tornillos ( normalmente 4 ) que fijan la fuente de alimentación a la caja del ordenador y retire la fuente de alimentación.

3 . Corte los conectores ( dejar unos centímetros de alambre en los conectores para que pueda utilizarlos más adelante en otros proyectos ) .

4 . Aprobación de la gestión del suministro de energía por cualquiera de dejar que se sientan desconectados durante unos pocos días , o mediante la unión de una resistencia de 10 ohmios entre un cable negro y rojo(a partir de los cables de potencia en el lado de salida ) . El uso de una resistencia de sólo tardará unos segundos para descargar por completo la alimentación eléctrica.

5 . Reunir las piezas que necesita : binding posts (terminales) , un LED con una resistencia de limitación de corriente , un interruptor (opcional ) , una resistencia de potencia ( 10 ohmios ,Potencia de 10W o superiores , ver Consejos) , y el tubo termorretráctil .6 . Abra la fuente de alimentación retirando los tornillos que unen la parte superior e inferior de la caja PSU .

7 . Ate los cables del mismo color juntos. Si usted tiene los cables no se incluyen aquí (marrón , etc) , ver los consejos .El código de color de los cables es: rojo = +5 V , Negro = Tierra (0 V ), Blanco = -5V , Amarillo = 12 V , Azul = -12V , Naranja = 3,3 V , Púrpura = +5 VStandby (no se utiliza ) , Gray = unidad está encendida ( salida) , y verde = Gire DC (entrada) .

8 . Taladrar orificios en un área libre de la caja de la fuente de alimentación mediante el marcado del centro de los agujeros con un clavo y un grifo del martillo . Utilice un Dremel parataladrar los agujeros iniciales seguidas de un escariador para agrandar los agujeros hasta que son del tamaño correcto de la prueba el montaje de los bornes de la mano. Además , perforeorificios para la alimentación LED y un interruptor de alimentación ( opcional).

9 . Atornille los bornes de conexión en sus correspondientes agujeros y fije la tuerca en la parte posterior .

10 . Conectar todas las piezas juntas._ Conecte uno de los cables rojos a la resistencia de potencia , todos los cables rojos restantes a los bornes de conexión de red ;_ Conecte uno de los cables negros al otro extremo de la resistencia de potencia , un cable negro a una resistencia ( 330 ohmios ) ánodo adjunto del LED ,un cable negro a la DC-El switch, todos los cables negros que quedan en el borne negro ;_ Conecte el blanco con el 5V- borne , amarillo al borne +12 V , el azul a la 12V- borne , el gris al cátodoel LED ;_ Tenga en cuenta que algunas fuentes de alimentación pueden tener ya sea un cable gris o marrón para representar "el poder bueno" / "poder ok" . Este cable debe serconectada a cualquiera de un cable naranja ( 3,3 V) o un cable rojo ( 5 V) para la fuente de alimentación para funcionar. En caso de duda , pruebe el voltaje más bajo primero( 3,3 V ) . Si una fuente de alimentación no es ATX o AT compatible , puede tener su propio esquema de color. Si el suyo se ve diferente que los cuadros demostradosaquí , asegúrese de hacer referencia a la posición de los cables conectados al conector AT / ATX en lugar de los colores.1 ._ Conecte el cable verde al otro terminal en el interruptor._ Asegúrese de que los extremos soldados están aislados en el tubo termorretráctil ._ Organizar los cables con cinta aislante o zip -dades .

1 . Compruebe si hay conexiones sueltas tirando suavemente de ellos. Inspeccione si hay cables pelados , y se cubre para evitar un cortocircuito. Ponga una gota de pegamento super-para pegar el LED a su agujero . Ponga la tapa de nuevo.

2 . Conecte el cable de alimentación en la parte posterior y en una toma de CA. Activa el interruptor principal en la PSU . Compruebe si la luz LED se enciende. Si tieneno, entonces encender presionando el interruptor que ha colocado en la parte delantera . Conecte una bombilla de 12 V en las diferentes tomas para ver si la fuente de alimentación funciona, tambiéncomprobar con un voltímetro digital. Debe quedar bien y trabajar como un encanto!_ Opciones: No es necesario un interruptor adicional , sólo tiene que conectar el verde y un cable negro juntos. La fuente de alimentación se controla mediante el interruptor trasero ,si es que existe. También no es necesario un LED, ignorar el cable gris . Corte corto y aislarlo del resto._ Algunas fuentes de alimentación nuevas tendrán cables " detección de voltaje " que necesitan ser conectados a los cables de voltaje actual para un funcionamiento correcto . En elpaquete de energía principal (el que tiene 20 hilos) , usted debe tener cuatro cables rojo y tres cables de color naranja. Si sólo tiene dos cables de color naranja , queTambién debe tener un cable marrón que debe estar conectada con la naranja . Si sólo tiene tres cables de color rojo , otro de alambre (a veces color rosa )

deben estar conectados a ellos ._ Si la fuente de alimentación no funciona , es decir , no hay luz LED , compruebe si el ventilador se encenderá. Si el ventilador de la fuente de alimentación está encendido, entonces elLED puede haber sido cableado incorrecto ( los cables positivo y negativo del LED pueden haber sido cambiados ) . Abra la caja y la fuente de alimentaciónvoltear los cables violeta o gris en el LED alrededor (asegúrese de que usted no pasar por alto la resistencia de LED) ._ Si no está seguro de la fuente de alimentación, probarlo en el equipo antes de la cosecha. ¿La potencia de los ordenadores en ? ¿Viene el ventilador PSUen ? Usted puede colocar sus cables del voltímetro en un conector adicional (para unidades de disco ) . Debe decir cerca de 5 V ( entre los cables rojo y negro ) . lade suministro que se han retirado puede parecer muerta porque no tiene una carga sobre sus productos y la habilitación de salida no puede ser conectada a tierra (verdehilos) .

_ Fuentes de alimentación ATX son " conmutadas " , sino que siempre debe tener algo de carga para funcionar correctamente. La resistencia de la energía está ahí paraenergía " residuos " , que le dará el calor , por lo que debe ser montado en la pared de metal para una refrigeración adecuada. Si usted siempre tendráalgo conectado a la red cuando está encendido , puede dejar de lado la resistencia de potencia .

_ Siéntase libre de añadir algunos pizazz a la caja de color gris mate .

_ También puede convertir esto en una fuente de alimentación variable - pero eso es otro artículo (pista: Utiliza un 317 IC con transistor de potencia ) .

_ Las tensiones que pueden salir de esta unidad son 24v ( 12 , -12 ) , 17v ( 5 , -12 ) , 12v ( 12 , 0), 10v ( 5 , -5 ) , 7v ( 12 , 5 ) , 5V ( 5 , 0 ), que debeser suficiente para la mayoría de las pruebas eléctrica . Muchas fuentes de alimentación ATX con un conector de 24 pines para las placas base no suministrará el -5V plomo. ¡Mirepara fuentes de alimentación ATX con un conector de 20 pines , un conector 20 +4 pin, o una fuente de alimentación AT si necesita -5V .

_ Puede añadir una salida de 3,3 voltios a la red mediante la conexión de los cables naranja a un poste ( asegurándose de que el cable marrón se mantiene conectado a lahaz naranja) pero ten cuidado de que comparten la misma potencia que el 5 voltios, y por lo tanto no debe exceder la potencia de salida total deestas dos salidas .

_ Para obtener más espacio se puede montar el ventilador en la parte exterior de la caja PSU_ Si no tiene ganas de soldadura nueve cables juntos a un puesto de conexión ( como es el caso de los cables de tierra ), puede cortar ellos en el PCB. 1-3cables deben estar bien. Esto incluye cortar los cables que no se te ocurra piense utilizar ._ La línea de +5 VSB es +5 V de espera ( por lo botones de encendido de la placa base , Wake on LAN, etc trabajo). Esto proporciona típicamente de 500-1000 mA

actual, incluso cuando las principales salidas de CC son "off" . Puede ser útil para conducir un LED de esto como una indicación de que el cable de alimentación está encendido.