cp64 release note firmware v2

8/3/2019 CP64 Release Note Firmware V2

1/7

IP 6600 engin e FW (Ver2.00) relea se note SIIT Confiden tia l

1

Product name IP-6600

Engine Firmware Version 2.00_XX Release note

November 29, 2004

Seiko I Information Tech

Design section 2


2/7


Table of contents

1. Introduction.................................................................................................................... 32. Environment of Operation.............................................................................................. 3

3. Changed Part from System Program V1.51_XX............................................................ 4

3.1. Functional Improvement Item.................................................................................. 4

3.2. Fault Correction Item............................................................................................... 4

4. Restriction Matter .......................................................................................................... 4

5. Additional Operation ...................................................................................................... 5

5.1 History printing operation ......................................................................................... 5

5.2 Paper Feed Adjustment ......................................................................................... 5

5.3 Registration Media Copy Operation....................................................................... 6

5.4 Saving of Waste Ink............................................................................................... 7

2


3/7


1. Introduction

This document describes the changed part and restriction matter of an IP-6600 enginesystem program (Ver2.00_XX).

2. Environment of Operation

The check of operation of this system program is carried out in the following

environments.

- Boot program : Ver1.10

- The HW environment

- IPB board : Ver1.0

- ASIC : Ver2.03

- ICB board : Ver3.10

3


4/7


3. Changed Part from System Program V1.51_XX

3.1. Functional Improvement Item

No. Internal

management No

Item Background Correspondence

1 523524

A curtailment ofwaste ink

There is indication that there are manywaste ink in cleaning..Then, change of a cleaning sequence isconsidered for the a curtailment ofwaste ink.

Normal cleaning sequence and slightcleaning sequence are changed.#WASTE SAVING menu is added topanel operation.

1 511 Head adjustmentpattern

Since a pattern name is not printed bythe head adjustment pattern, it isunclear.

A name is printed to each pattern.

2 509 History print The log of a head maintenance cannotget in user mode.

History printing operation is added touser mode.Chapter 5 is referred to about operation.

3 507 Paper feedadjustment

Paper feed adjustment cannot beperformed during printing.

It changes so that adjustment may bepossible by the up/down key duringon-line printing.Chapter 5 is referred to about operation.

4 499 Media ENTRY Menu Media information cannot be copied tonew area.

Copy operation is added.Chapter 5 is referred to about operation.

3.2. Fault Correction Item

No. Internalmanagement No

Item Phenomenon Cause Measure

1 521 Feed adjustmentpattern1

Vacuum FAN does not stopafter a feed adjustmentpattern printing end.

The FAN stop wasomitted after the printingend.

It corrects so that a FANstop can be carried outafter a printing end.

2 523 Feed adjustmentpattern2

The color stripe of a feedadjustment pattern overlaps,and is printed.Especially a draft pattern isconspicuous.

Only the color stripe wasgenerated for a long timethan an actual testpattern.

It corrects so that a colorstripe may be generatedby the same length as atest pattern.

3 518 Head adjustmentpattern printing

It cannot cancel even if itpushes a cancel key duringhead adjustment patternprinting.

In I-pos adjustmentpattern printing, print

cancel processing wasnot operating normally.

It corrects so that it cancancel normally.

4 508 An I-posi adjustmentpattern

The parameter numericalvalue in an adjustmentpattern cannot be read.

The numerical value inwhich it made a mistakeon the right numericalvalue was printed.

It corrects so that onlythe right numerical valuemay be printed.

5 230205

System error The system error of F_es000X may occur at the timeof a power supply OFF.

There was a case whichbreaks informationrequired of power OFFprocessing.

A work area is takenenough, and it correctsso that requiredinformation may not bebroken.

6 534 Abnormal cartridge If the abnormalities in acartridge are detected whenstarting printing, capopening and closing may berepeated.

Processing when theabnormalities in acartridge occur was notable to be considered.

If ink is in a sub tankeven if the abnormalitiesin a cartridge occur, it willcorrect so that printingmay be performed.

4. Restriction Matter

Nothing

4


5/7


5. Additional Operation

5.1 History printing operation

History printing operation is added to user mode.The menu of history printing is added in a FUNC(function) menu.

A maintenance situation can be printed if this menu is performed.

The ink system cleaning situation saved to equipment is printed.

#HISTORY PRINT

>

Nothing

5.2 Paper Feed Adjustment

A paper feed adjustment value can be changed by the following operations during on-line

printing.

PRINT READY

ROLL:64(PAPER)idle state

Start to receive data

Blink data LEDPRINTING

ROLL:64(PAPER)

Push the ^ key or v key (notes: those key are ignored in the first

scan and the last scan)FINE ADJ: 099.80%

*099.80%

- During a PRINTING display, a push on the ^ key

or the v key displays the paper feed adjustment

current value.

- Up(Down) 0.01% by ^ (v) key.

-The changed value is reflected in printing.-When there is no key operation for 3 seconds,

return to the original display.

The 1st line is a printing start value.

The value of the 1st line does not change till a

printing end.

However, in the cleaning mode 2, it becomes the

changed value after cleaning execution.

Range : 97.00% - 103.00%

5


6/7


5.3 Registration Media Copy Operation

The copy of media information is possible.

1) Parameter copy sourceThe copy source of a media registration number is chosen.

#COPY SOURCE

>01

Paper number: 01-20 However, only the number registered is displayed.

2) Parameter copy destination

The copy destination number is chosen.

# COPY DEST

>01->01*

Paper number: 01-20 * (asterisk) displays on a registered number.

1) Choose a copy source number.

#COPY SOURCE>01

ENTER key

Parameter change by ^ (v) key is possible.

(A copy source number displays only the number

registered)

#COPY SOURCE*01

^, v key

#COPY SOURCE*13

A copy source number is determined by the ENTER key.

ENTER key

#COPY SOURCE>13

note) When the CANCEL key is pushed in the middle of each menu, return to the first

menu.

6


7/7


2) Choose a copy destination.

#COPY DEST>13->01*

A left value(13) is a copy source number.

ENTER key Parameter change by ^ (v) key is possible.

(A copy destination number is displayed to 01-20)

When a copy destination is registered, * displays

after a numerical value.

#COPY DEST* 13->01*

^, v key

#COPY DEST* 13->20

A copy destination number is determined by the

ENTER key.

ENTER key

#COPY DEST* 13 ->20 OK?

Copy execution by the ENTER key.

ENTER key

#COPY DEST>13->20*

Note) When the CANCEL key is pushed in the middle of each menu, return to the first

menu.

5.4 Saving of Waste Ink

The waste ink saving setting menu in automatic cleaning (it adds in a service menu)

waste ink saving setup

A waste ink saving setup in automatic cleaning is performed.

#WASTE SAVING>NORMAL

NORMAL: Usually perform automatic cleaning (initial value).

SAVE: Perform automatic cleaning in saved waste ink.

7

cp64 release note firmware v2

Documents