crompton ed 3
TRANSCRIPT
7/25/2019 Crompton ED 3
http://slidepdf.com/reader/full/crompton-ed-3 1/7
fold
fold
fold
fold
fold
fold
1
2
3456
7
891011
12
13 14
1516
17 18
19 20 21 22
Sheet of 3
2a
2a
7/25/2019 Crompton ED 3
http://slidepdf.com/reader/full/crompton-ed-3 2/7
2324
26
27
28
25
26a
Sheet 2 of 3
7/25/2019 Crompton ED 3
http://slidepdf.com/reader/full/crompton-ed-3 3/7
29
30
31
32
33
34
35
36
37
38
39
40 41
top
top
42 43
44
Sheet 3 of 3
7/25/2019 Crompton ED 3
http://slidepdf.com/reader/full/crompton-ed-3 4/7
2
2
2
2
2.1 - Start glueing the rear face of #2 at the upper sides.Make sure the two corners are aligned.Finish one side, then the other.
The hull is in three main pieces. Start with #1 (outer-lower hull) and #2 (inner hull)
Note that tabs go on the INSIDE
Inside of rear face. Note tabs on the inside.There are two small plain pieces (#2a) to fillthe area where the air grills (#23 and #24) will go
2a
(not shown)
1 23 4
4.2 - Attach #1 to #2. Apply glue sparingly.4.2.1 - Start at the rear bottom edge4.2.2 - glue front bottom edge.4.2.3 - glue sides only where shown
4.2.1
4.2.2
4.1 - Check #1 and #2 carefully for fit. Adjust #2 as necessary.
4.2.3
7/25/2019 Crompton ED 3
http://slidepdf.com/reader/full/crompton-ed-3 5/7
5 6
7 8
1
2
6.1 - assemble engine pieces.Note that #4 is wrapped around #39, (a 4-ply blank piece) then trimmed
4
39
6
7
5
3
40
41
NOTE: do NOT assemble the entire engine yet
right engine pieces are assembled as shown.left engine is similar
43
42
7.1 - attach #43 (chain)7.2 - add #3, #4, #5, #6in that order
6
54 3
11
1210
9
8
39
8910
11
12
42
39
2324
left engine pieces
engine color in final model is alighter shade of gray
radiator grills
7/25/2019 Crompton ED 3
http://slidepdf.com/reader/full/crompton-ed-3 6/7
interior complete, ready to add outer shell
9 10
23
24
13
14
15
16
1718
21
19
22
20
25
26
attach #25 to theunderside of #26. Glue only around the4 edges.
1
2
11 - attach #26 to #1/#211.1 - apply glue only alongthe edges shown on one side11.2 - apply glue to the otherside, the same way
glue tabs on both sides
11.3 - glue #26rear side tabsto rear of #2
11.4 - glue #26rear panel to#2 rear panel
11.5 - glue #26 bottom to #1 bottomNote: glue only at the front
12.1 - glue top tabs to inside front panels
12.2 - add #26a fillers between tabs
12.3 - glue #26 outside front panels to #2 inside front panels
13 - assemble track units. arrows point toward front.
11
12 13
7/25/2019 Crompton ED 3
http://slidepdf.com/reader/full/crompton-ed-3 7/7
14 15
16 17
14.1 - Wrap outer tracks (#31, #32) around track frames (#29,#30)
14.2 - add spacers ( to track units (exact placement is not important)
3135
3629
3334
30
32
37
37
38
38
27
28
4.5-inch Howitzer:Model shown here iscomplete with wheelswhich will be omittedwhen mounted insidethe vehicle.
Whitemodel of 4.5-inch howitzer without wheels, inside the ED3.Small tabs beneath the short axle were added as adhoc supports -the model includes a long axle that does not need the tabs.