cutting accessory guide section 5 heavy duty9100-001-325 rev.a
TRANSCRIPT
Introduction
Cautions and Warnings
When using Stryker burs and blades
• Read and understand any specific instructions that accompanyindividual accessories and powered instruments.
• Ensure bur or blade is properly inserted and securely lockedin position before running your powered instrument.
• Bending or prying with a bur or blade may cause it to break andleave a piece in the wound site or become a projectile. Always wearsafety goggles/eye protection when operating powered instruments.
• Using irrigation while operating burs and blades will help reducethe possibility of thermal necrosis.
• WARNING: DO NOT reuse, reprocess, or repackage this device.This device is intended for a single use only. This device maynot withstand chemical vapor, or high temperature sterilizationreprocessing. Design features may make cleaning difficult. Reusemay create a serious risk of contamination and may compromise thestructural integrity of the device resulting in operational failure. Criticalproduct information may be lost if the device is re-packaged. Failureto comply may lead to infection or cross-infection and result in patientand/or health care staff injury.
Terms and Cautions
Terms
Cut Edge (A)
Blade Height (B)
Cut Depth (C)
Stop Depth (D)
Teeth per cm/inch Signifying the aggressiveness of the blade;less teeth per inch generally creates a more aggressive, fast cutwhereas more teeth per inch generally creates a more precise,controlled cut.
Head Diameter (E)
Head Length (F)
Overall Length (G)
Cutting Thickness (H) The width thickness of teeth that arebent away in an alternating vertical pattern.
Material Thickness (I) The thickness of the blade not including theoffset tooth design.
A
E
B
C
A
A
F
F
G
D
H
I
H
2
*Special Note All blades are to scale. 9100-001-325 Rev. B
HeavyDuty5
Part Number DescriptionProduct
6203-000-000 System 6Single Trigger Rotary
4203-000-000 System 5Single Trigger Rotary
6293-000-000 Electric System 6Single Trigger Rotary
6295-000-000 Electric System 6Dual Trigger Rotary
6205-000-000 System 6Dual Trigger Rotary
4205-000-000 System 5Dual Trigger Rotary
Heavy Duty Rotary Drills
HeavyDuty5
Stryker Customer Service 800 253 32103
Heavy Duty High Speed Drill Bits
Part Number Diam. mmDescription Length mm
0277-082-085s7, pkg. of 6 2.05/64” Drill Bit, Stainless Steel 128
0277-082-086s5, pkg. of 6 2.43/32” Drill Bit, Stainless Steel 128
0277-082-085s5, pkg. of 6 2.87/64” Drill Bit, Stainless Steel 128
0277-082-087s6, pkg. of 6 3.21/8” Drill Bit, Stainless Steel 128
0277-082-086 3.69/64” Drill Bit, Stainless Steel 84
Non Sterile Sterile
Part Number Diam. mmDescription Length mm
0277-082-085s3 1.61/16” Drill Bit, Stainless Steel 128
0277-082-085s4 2.05/64” Drill Bit, Stainless Steel 128
0277-082-085s1 2.43/32” Drill Bit, Stainless Steel 128
0277-082-085s2 2.87/64” Drill Bit, Stainless Steel 128
0277-082-087s1 3.21/8” Drill Bit, Stainless Steel 128
0277-082-086s1 3.69/64” Drill Bit, Stainless Steel 128
ForUseWith:
Drill Bit Shank
6203-000-000 6205-000-000
4203-000-000
HeavyDuty5
Stryker Customer Service 800 253 3210 4
6293-000-000
4205-000-000
6293-000-000
Part Number DescriptionProduct
Heavy Duty Reciprocating Saws
6206-000-000 System 6Reciprocating Saw
6296-000-000 Electric System 6Reciprocating Saw
4206-000-000 System 5Reciprocating Saw
HeavyDuty5
Stryker Customer Service 800 253 32105
Heavy Duty Reciprocating BladesForUseWith:
Blade Material Cutting Cut Fixed Point TeethProduct and Part Number Height Thickness Thickness Edge Travel per inch
4206-000-000
0277-096-251 mm 6.0 .77 1.14 47.5 3.6
Offset inch .24 .031 .045 1.87 .14 16
0277-096-275 mm 12.7 .64 .91 70.0 3.6
Double Sided inch .50 .025 .036 2.76 .14 20
0277-096-276 mm 12.7 .77 1.04 70.0 3.6
Double Sided Offset inch .50 .031 .041 2.76 .14 20
Short inch .25 .025 .040 2.36 .14 16
Blade Mount
6206-000-000
6296-000-000
A spring lock holds thecutting blade in place.No tools necessary forblade changes.
HeavyDuty5
Stryker Customer Service 800 253 3210 6
0277-096-250 mm 6.3 .64 1.02 60.0 3.6
Heavy Duty Reciprocating Blades
Blade Material Cutting Cut Fixed Point TeethProduct and Part Number Height Thickness Thickness Edge Travel per inch
0277-096-277 mm 12.7 .99 1.16 70.0 3.6
Double Sided Offset inch .50 .039 .046 2.76 .14 20
0277-096-278 mm 12.7 .97 .97 70.0 3.6
Long, Double Sided inch .50 .038 .038 2.76 .14 20
0277-096-281 mm 12.7 1.27 1.40 70.0 3.6
Offset inc .50 .050 .055 2.76 .14 20
0277-096-282 mm 12.7 1.24 1.24 81.0 3.6
No Offset inch .50 .049 .049 3.20 .14 20
HeavyDuty5
Stryker Customer Service 800 253 32107
ForUseWith:
4206-000-000
Blade Mount
A spring lock holds thecutting blade in place.No tools necessary forblade changes.
6206-000-000
6296-000-000
Heavy Duty Reciprocating Blades
2.76/47.5 .032/0.77 .24/6.0 14/3.56 16/6.30
Blade Material Cutting Cut Fixed Point TeethProduct and Part Number Height Thickness Thickness Edge Travel per inch
0277-096-300 mm 6.2 .64 1.02 77.5 3.6
Offset, Long inch .25 .025 .040 3.06 .14 16
0277-096-325 mm 11.2 .79 1.14 77.5 3.6
Double Sided Offset inch .44 .031 .045 3.06 .14 16
0277-096-326 mm 11.0 1.22 1.60 77.5 3.6
Offset inch .43 .048 .063 3.06 .14 16
0277-096-327 mm 12.5 .79 1.09 74.0 3.6
Offset inch .49 .031 .043 2.92 .14 16
HeavyDuty5
Stryker Customer Service 800 253 3210 8
ForUseWith:
4206-000-000
Blade Mount
A spring lock holds thecutting blade in place.No tools necessary forblade changes.
6206-000-000
6296-000-000
Heavy Duty Sternum Saws
Part Number DescriptionProduct
6207-000-000 System 6Sternum Saw
6297-000-000 Electric System 6Sternum Saw
4207-000-000 System 5 Sternum Saw
HeavyDuty5
Stryker Customer Service 800 253 32109
Blades for Sternum Saw
Product
Heavy Duty Sternum Blades
Teeth per in/cm: 20/7.87
Teeth per in/cm: 20/7.87
Teeth per in/cm: 20/7.87
inch .26 .025 .040 1.20
inch .25 .031 .040 1.26
inch .25 .025 .040 1.26
0296-097-102
inch .23 .025 .040 1.24
6207-097-101 mm 6.5 .64 1.02 30.5
0298-097-101 mm 6.3 .64 1.02 32.0
mm 6.0 .64 1.02 31.5
Non-Sterile 100/packTeeth per in/cm: 20/7.87
0298-097-104
inch .25 .031 .040 1.26
Blade Material Cutting CutPart Number Height Thickness Thickness Edge
0298-097-100 mm 6.3 .79 1.02 32.0
ForUseWith:
Blade Mount
4207-000-000 6207-000-000
6297-000-000
HeavyDuty5
mm 6.3 .79 1.02 32.0
Stryker Customer Service 800 253 3210 10
Heavy Duty Precision Blade
ForUseWith:
Blade Mount
6525-127-105 mm 25.0 1.27 1.33 105.0
inch .98 .050 .052 4.13
6209-000-000 6299-000-000
Precision® Heavy Duty Sagittal Saw
Part Number DescriptionProduct
6209-000-000 System 6Precision® Saw
6299-000-000 Electric System 6Precision® Saw
HeavyDuty5
Stryker Customer Service 800 253 321011
Material CuttingProduct and Part Number Cut Edge Thickness Thickness Cut Depth
Part Number DescriptionProduct
Heavy Duty Sagittal Saws
6208-000-000 System 6Sagittal Saw
6298-000-000 Electric System 6Sagittal Saw
4208-000-000 System 5Sagittal Saw
HeavyDuty5
Stryker Customer Service 800 253 3210 12
System 6 Blades
ForUseWith:
Heavy Duty Sagittal Blades
6113-089-090 mm 13.0 .89 .89 90.0
No Offset inch .51 .035 .035 3.54
6113-107-090 mm 13.0 1.07 1.07 90.0
No Offset inch .51 .042 .042 3.54
6113-119-090 mm 13.0 1.19 1.19 90.0
No Offset inch .51 .047 .047 3.54
6113-127-090 mm 13.0 1.27 1.27 90.0
No Offset inch .51 .050 .050 3.54
6113-137-090 mm 13.0 1.37 1.37 90.0
No Offset inch .51 .054 .054 3.54
6113-147-090 mm 13.0 1.47 1.47 90.0
No Offset inch .51 .058 .058 3.54
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
6113-127-075 mm 13.0 1.27 1.27 75.0
No Offset inch .51 .050 .050 2.95
Blade Mount
4208-000-000 6208-000-000
6298-000-000
6113-127-060 mm 13.0 1.27 1.27 60.0
No Offset inch .51 .050 .050 2.36
HeavyDuty5
Stryker Customer Service 800 253 321013
System 6 Blades
ForUseWith:
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
Heavy Duty Sagittal Blades
Blade Mount
6113-127-100 mm 13.0 1.27 1.27 100.0
No Offset inch .51 .050 .050 3.94
6113-137-100 mm 13.0 1.37 1.37 100.0
No Offset inch .51 .054 .054 3.94
6118-147-060 mm 18.0 1.47 1.47 60.0
No Offset inch .71 .058 .058 2.36
6118-089-075 mm 18.0 .89 .89 75.0
No Offset inch .71 .035 .035 2.95
6118-127-075 mm 18.0 1.27 1.27 75.0
No Offset inch .71 .050 .050 2.95
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 14
6208-000-000
6298-000-000
System 6 Blades
Heavy Duty Sagittal Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
6118-089-090 mm 18.0 .89 .89 90.0
No Offset inch .71 .035 .035 3.54
6118-097-090 mm 18.0 .97 .97 90.0
No Offset inch .71 .038 .038 3.54
6118-119-090 mm 18.0 1.19 1.19 90.0
No Offset inch .71 .047 .047 3.54
6118-127-090 mm 18.0 1.27 1.27 90.0
No Offset inch .71 .050 .050 3.54
6118-137-090 mm 18.0 1.37 1.37 90.0
No Offset inch .71 .054 .054 3.54
Blade MountForUseWith:
6118-119-100 mm 18.0 1.19 1.19 100.0
No Offset inch .71 .047 .047 3.94
6118-127-100 mm 18.0 1.27 1.27 100.0
No Offset inch .71 .050 .050 3.94
6118-137-100 mm 18.0 1.37 1.37 100.0
No Offset inch .71 .054 .054 3.94
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321015
6208-000-000
6298-000-000
System 6 Blades
ForUseWith:
Heavy Duty Sagittal Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
6125-089-075 mm 25.0 .89 .89 75.0
No Offset inch 1.00 .035 .035 2.95
Blade Mount
6118-119-110 mm 18.0 1.19 1.19 110.0
No Offset inch .71 .047 .047 4.33
6118-127-110 mm 18.0 1.27 1.27 110.0
No Offset inch .71 .050 .050 4.33
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 16
6208-000-000
6298-000-000
System 6 Blades
ForUseWith:
Heavy Duty Sagittal Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
Blade Mount
6125-147-090 mm 25.0 1.47 1.47 90.0
No Offset inch .98 .058 .058 3.54
6125-089-090 mm 25.0 .89 .89 90.0
No Offset inch .98 .035 .035 3.54
6125-097-090 mm 25.0 .97 .97 90.0
No Offset inch .98 .038 .038 3.54
6125-107-090 mm 25.0 1.07 1.07 90.0
No Offset inch .98 .042 .042 3.54
6125-119-090 mm 25.0 1.19 1.19 90.0
No Offset inch .98 .047 .047 3.54
6125-127-090 mm 25.0 1.27 1.27 90.0
No Offset inch .98 .050 .050 3.54
6125-137-090 mm 25.0 1.37 1.37 90.0
No Offset inch .98 .054 .054 3.54
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321017
6208-000-000
6298-000-000
System 6 Blades
ForUseWith:
Heavy Duty Sagittal Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
Blade Mount
6125-100-110 mm 25.0 1.00 1.00 110.0
No Offset inch .98 .040 .040 4.33
6125-137-110 mm 25.0 1.37 1.37 110.0
No Offset inch .98 .054 .054 4.33
6125-127-100 mm 25.0 1.27 1.27 100.0
No Offset inch .98 .050 .050 3.94
6125-137-100 mm 25.0 1.37 1.37 100.0
No Offset inch .98 .054 .054 3.94
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 18
6208-000-000
6298-000-000
System 6 Blades
Heavy Duty Sagittal Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
ForUseWith:
6213-119-070 mm 13.0 1.19 1.19 70.0
No Offset inch .51 .047 .047 2.76
6213-127-070 mm 13.0 1.27 1.27 70.0
No Offset inch .51 .050 .050 2.76
6213-137-070 mm 13.0 1.37 1.37 70.0
No Offset inch .51 .054 .054 2.76
6221-100-090 mm 21.0 1.00 1.00 90.0
No Offset inch .83 .040 .040 3.54
6221-119-090 mm 21.0 1.19 1.19 90.0
No Offset inch .83 .047 .047 3.54
6221-127-090 mm 21.0 1.27 1.27 90.0
No Offset inch .83 .050 .050 3.54
6221-137-090 mm 21.0 1.37 1.37 90.0
No Offset inch .83 .054 .054 3.54
6221-147-090 mm 21.0 1.47 1.47 90.0
No Offset inch .83 .058 .058 3.54
Blade Mount
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321019
6208-000-000
6298-000-000
Dual Cut Blades
Heavy Duty Sagittal Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
ForUseWith:
4111-089-075 mm 11.0 .80 .89 75.0
Offset inch .43 .032 .035 2.95
4111-089-090 mm 11.0 .80 .89 90.0
Offset inch .43 .032 .035 3.54
4111-135-090 mm 11.0 1.19 1.35 90.0
Offset inch .43 .047 .053 3.54
4111-107-090 mm 11.0 .97 1.07 90.0
Offset inch .43 .038 .042 3.54
4111-119-090 mm 11.0 1.04 1.19 90.0
Offset inch .43 .041 .047 3.54
4111-127-090 mm 11.0 1.13 1.27 90.0
Offset inch .43 .045 .050 3.54
4111-147-075 mm 11.0 1.38 1.47 75.0
Offset inch .43 .055 .058 2.95
Blade Mount
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 20
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
Dual Cut Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
4113-119-090 mm 13.0 1.04 1.19 90.0
Offset inch .52 .041 .047 3.54
Blade Mount
4118-127-075 mm 18.0 1.13 1.27 75.0
Offset inch .71 .045 .050 2.95
4118-089-075 mm 18.0 .80 .89 75.0
Offset inch .71 .032 .035 2.95
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321021
6208-000-000
6298-000-000
Dual Cut Blades
ForUseWith:
Heavy Duty Sagittal Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
4118-119-090 mm 18.0 1.04 1.19 90.0
Offset inch .71 .041 .047 3.54
4118-127-090 mm 18.0 1.13 1.27 90.0
Offset inch .71 .045 .050 3.54
4118-135-090 mm 18.0 1.19 1.35 90.0
Offset inch .71 .047 .053 3.54
4118-127-100 mm 18.0 1.13 1.22 100.0
Offset inch .71 .045 .048 3.94
4118-137-090 mm 18.0 1.23 1.37 90.0
Offset inch .71 .049 .054 3.54
4118-147-090 mm 18.0 1.38 1.47 90.0
Offset inch .71 .055 .058 3.54
Blade Mount
4118-089-090 mm 18.0 .80 .89 90.0
Offset inch .71 .032 .035 3.54
4118-097-090 mm 18.0 .87 .97 90.0
Offset inch .71 .034 .038 3.54
4118-107-090 mm 18.0 .97 1.07 90.0
Offset inch .71 .038 .042 3.54
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 22
6208-000-000
6298-000-000
Dual Cut Blades
ForUseWith:
Heavy Duty Sagittal Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
4125-064-075 mm 25.0 .51 .64 75.0
Offset inch .98 .020 .025 2.95
4125-089-075 mm 25.0 .80 .89 75.0
Offset inch .98 .032 .035 2.95
Blade Mount
4118-135-105 mm 18.0 1.19 1.35 105.0
Offset inch .71 .047 .053 4.12
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321023
6208-000-000
6298-000-000
Dual Cut Blades
ForUseWith:
Heavy Duty Sagittal Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
4125-137-090 mm 25.0 1.23 1.37 90.0
Offset inch .98 .049 .054 3.54
4125-089-090 mm 25.0 .80 .89 90.0
Offset inch .98 .032 .035 3.54
4125-097-090 mm 25.0 .88 .97 90.0
Offset inch .98 .035 .038 3.54
4125-107-090 mm 25.0 .97 1.07 90.0
Offset inch .98 .038 .042 3.54
4125-119-090 mm 25.0 1.04 1.19 90.0
Offset inch .98 .041 .047 3.54
4125-127-090 mm 25.0 1.13 1.27 90.0
Offset inch .98 .045 .050 3.54
4125-135-090 mm 25.0 1.19 1.35 90.0
Offset inch .98 .047 .053 3.54
4125-147-090 mm 25.0 1.38 1.47 90.0
Offset inch .98 .055 .058 3.54
Blade Mount
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 24
6208-000-000
6298-000-000
Dual Cut Blades
ForUseWith:
Heavy Duty Sagittal Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
Blade Mount
4125-127-100 mm 25.0 1.13 1.27 100.0
Offset inch .98 .045 .050 3.94
4135-089-064 mm 35.0 .80 .89 64.0
Offset inch 1.38 .032 .035 2.52
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321025
6208-000-000
6298-000-000
Dual Cut Blades
ForUseWith:
Heavy Duty Sagittal Blades
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
Teeth: minimum offset inch .984 .058 3.543
Blade Mount
4218-147-060 mm 18.0 1.47 1.47 60.0
No Offset inch .71 .058 .058 2.36
HeavyDuty5
4208-000-000
4225-089-090 mm 25.0 .87 .89 90.0
Teeth: minimum offset inch .98 .034 .035 3.54
4225-127-090 mm 25.0 1.23 1.27 90.0
Teeth: minimum offset inch .98 .049 .050 3.54
4225-147-090 mm 25.0 1.47 1.47 90.0
No Offset inch .98 .058 .058 3.54
Stryker Customer Service 800 253 3210 26
6208-000-000
6298-000-000
Dual Cut Blades
ForUseWith:
Heavy Duty Sagittal Blades
Teeth: minimum offset
Cut Material Cutting CutProduct and Part Number Edge Thickness Thickness Depth
4221-120-085 mm 21.0 1.20 1.20 85.0
No Offset inch .83 .047 .047 3.35
4221-140-090 mm 21.0 1.40 1.40 90.0
No Offset inch .83 .055 .055 3.54
Blade Mount
4211-127-075 mm 11.0 1.19 1.27 90.0
Teeth: minimum offset inch .43 .047 .050 3.54
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321027
6208-000-000
6298-000-000
2108 Series
ForUseWith:
Heavy Duty Sagittal Blades
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-100-000 mm 25.0 .64 1.02 73.0
Teeth: minimum offset inch .98 .025 .040 2.88 16
2108-105-000 mm 25.0 .89 .98 73.0
Offset inch .98 .035 .039 2.88 12
2108-103-000 mm 12.5 .89 .97 89.5
Offset inch .49 .035 .038 3.53 16
2108-102-000 mm 25.0 .89 .98 89.5
Offset inch .98 .035 .039 3.53 12
Blade Mount
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 28
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-109-000 mm 21.0 .89 .98 84.5
Offset inch .82 .035 .039 3.32 12
2108-110-000 mm 25.0 1.24 1.45 73.0
Offset inch .98 .049 .057 2.88 12
2108-111-000 mm 25.0 1.24 1.45 79.5
Offset inch .98 .049 .057 3.13 12
Blade Mount
2108 Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-113-000 mm 16.5 1.24 1.73 34.0
Offset inch .65 .049 .068 1.34 12
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321029
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-115-000 mm 18.5 .79 .97 73.0
Offset inch .73 .031 .038 2.88 12
2108-120-000 mm 18.5 .64 1.02 60.5
Offset inch .73 .025 .040 2.38 12
Blade Mount
2108 Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-118-000 mm 25.0 1.24 1.24 79.5
No Offset inch .98 .049 .049 3.13 12 HeavyDuty5
4208-000-000
2108-125-000 mm 40.5 .64 1.02 47.5
Offset, Safedge™ inch 1.59 .025 .040 1.88 23
Stryker Customer Service 800 253 3210 30
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-131-000 mm 17.5 .64 1.04 47.5
Offset, Safedge™ inch .68 .025 .041 1.88 23
2108-137-000 mm 80.0 .64 1.02 28.0
Offset inch 3.15 .025 .040 1.09 23
Blade Mount
2108 Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-140-000 mm 29.0 .64 1.02 58.0
Offset inch 1.14 .025 .040 2.28 12
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321031
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-144-000 mm 5.8 .64 .76 24.0
Offset inch .23 .025 .030 .96 23
2108-148-000 mm 9.0 .64 .76 34.5
Offset inch .36 .025 .030 1.36 23
2108-145-000 mm 9.0 .64 .76 24.0
Offset inch .36 .025 .030 .96 23
2108-146-000 mm 6.6 .64 1.12 27.9
Offset inch .26 .025 .044 1.10 23
Blade Mount
2108 Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 32
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-151-000 mm 25.0 1.19 1.19 85.0
No Offset inch .98 .047 .047 3.34 12
2108-150-000 mm 12.5 .64 1.02 73.0
Offset inch .49 .025 .040 2.88 16
2108-152-000 mm 12.5 1.19 1.19 81.5
No Offset inch .49 .047 .047 3.20 12
Blade Mount
2108 Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-155-000 mm 12.5 1.27 1.45 73.0
Offset inch .49 .050 .057 2.88 12
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321033
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-160-000 mm 25.0 .89 1.27 73.0
Offset inch .97 .035 .050 2.88 10
2108-175-000 mm 9.5 .64 1.02 60.5
Offset inch .37 .025 .040 2.38 16
2108-156-000 mm 12.5 1.27 1.45 79.5
Offset inch .49 .050 .057 3.13 12
Blade Mount
2108 Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-158-000 mm 12.5 1.27 1.27 81.5
No Offset inch .49 .050 .050 3.20 12 HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 34
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
No Offset
2108-182-000 mm 18.5 1.24 1.24 83.5
No Offset inch .73 .049 .049 3.29 12
2108-177-000 mm 25.0 1.32 1.32 86.5
No Offset inch .98 .052 .052 3.41 12
2108-176-000 mm 25.0 1.47 1.47 79.5
No Offset inch .98 .058 .058 3.13 12
Blade Mount
2108 Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-183-000 mm 29.0 1.27 1.27 83.5
No Offset inch 1.14 .050 .050 3.29 12
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321035
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-185-000 mm 18.5 1.27 1.27 104.0
No Offset inch .73 .050 .050 4.10 12
2108-189-000 mm 25.0 1.27 1.27 81.5
No Offset inch .98 .050 .050 3.20 12
2108-193-000 mm 25.0 1.04 1.04 81.5
No Offset inch .98 .041 .041 3.20 12
2108-192-000 mm 20.0 1.27 1.27 38.0
inch .80 .050 .050 1.50 -
Blade Mount
2108 Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 36
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-197-000 mm 48.5 .64 1.02 61.0
Offset inch 1.90 .025 .040 2.40 18
2108-195-000 mm 48.5 .97 .97 90.0
No Offset inch 1.90 .038 .038 3.54 18
Blade Mount
2108 Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321037
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-107-001 mm 29.0 .89 .97 73.0
Offset inch 1.14 .035 .038 2.89 12
2108-107-004 mm 36.0 1.19 1.55 64.0
Offset inch 1.41 .047 .061 2.53 16
Blade Mount
2108 Special Conversion Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
2108-107-005 mm 29.0 1.24 1.24 84.0
No Offset inch 1.14 .049 .049 3.31 12
Stryker Customer Service 800 253 3210 38
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-109-001 mm 20.5 .89 .97 94.5
Offset inch .82 .035 .038 3.73 12
2108-107-009 mm 34.0 .81 .81 64.0
No Offset inch 1.38 .032 .032 2.53 12
Blade Mount
2108 Special Conversion Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-109-003 mm 20.0 .89 .97 80.0
Offset inch .78 .035 .038 3.16 10
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321039
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-110-002 mm 25.0 1.24 1.24 89.5
No Offset inch .98 .049 .049 3.53 12
2108-109-004 mm 20.5 1.24 1.24 85.0
No Offset inch .82 .049 .049 3.32 12
Blade Mount
2108 Special Conversion Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
2108-110-006 mm 25.0 1.24 1.24 90.5
No Offset inch .98 .049 .049 3.57 12
Stryker Customer Service 800 253 3210 40
4206-000-000
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-120-009 mm 18.5 1.24 1.24 60.5
No Offset inch .73 .049 .049 2.39 12
2108-120-006 mm 18.5 .64 .91 63.0
Offset inch .73 .025 .036 2.49 16
Blade Mount
2108 Special Conversion Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-125-001 mm 40.5 .64 1.02 37.5
Offset inch 1.64 .025 .040 1.49 23
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321041
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-145-001 mm 9.0 .64 .76 24.5
Offset inch .36 .025 .030 .98 23
2108-140-006 mm 31.0 .64 .91 63.0
Offset inch 1.23 .025 .036 2.49 16
2108-130-001 mm 25.0 .64 1.02 47.5
Offset inch .98 .025 .040 1.89 23
Blade Mount
2108 Special Conversion Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
2108-148-003 mm 9.0 .38 .58 22.5
Offset inch .36 .015 .023 1.90 23
Stryker Customer Service 800 253 3210 42
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
No Offset
2108-152-006 mm 12.5 .89 .89 88.0
No Offset inch .49 .035 .035 3.47 12
2108-152-002 mm 12.5 1.19 1.19 61.5
No Offset inch .49 .047 .047 2.43 12
2108-151-001 mm 25.0 1.19 1.19 95.0
No Offset inch .98 .047 .047 3.75 12
Blade Mount
2108 Special Conversion Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-158-002 mm 12.5 1.27 1.27 73.0
No Offset inch .49 .050 .050 2.88 12
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321043
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-176-001 mm 25.0 1.47 1.47 98.5
No Offset inch .98 .058 .058 3.89 12
2108-161-002 mm 27.0 1.24 1.45 73.0
Offset inch 1.07 .049 .057 2.89 10
Blade Mount
2108 Special Conversion Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
2108-176-002 mm 25.0 1.47 1.47 93.0
No Offset inch .98 .058 .058 3.67 12
Stryker Customer Service 800 253 3210 44
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-182-006 mm 18.5 1.32 1.32 86.0
No Offset inch .73 .052 .052 3.41 12
2108-177-001 mm 25.0 1.32 1.32 82.0
No Offset inch .98 .052 .052 3.23 12
2108-176-003 mm 25.0 1.47 1.47 85.0
No Offset inch .98 .058 .058 3.36 12
Blade Mount
2108 Special Conversion Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-182-008 mm 18.5 1.24 1.24 73.0
No Offset inch .73 .049 .049 2.89 12
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321045
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-183-013 mm 25.0 1.27 1.27 99.0
No Offset inch .98 .050 .050 3.91 12
2108-183-003 mm 29.0 1.32 1.32 84.0
No Offset inch 1.14 .052 .052 3.31 12
2108-183-001 mm 29.0 .97 .97 84.0
No Offset inch 1.14 .038 .038 3.31 12
2108-182-010 mm 19.0 1.32 1.32 98.0
No Offset inch .75 .052 .052 3.86 12
Blade Mount
2108 Special Conversion Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 46
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-185-002 mm 18.5 1.27 1.27 99.0
No Offset inch .73 .050 .050 3.91 12
2108-185-001 mm 18.5 1.24 1.24 104.0
No Offset inch .73 .049 .049 4.12 12
Blade Mount
2108 Special Conversion Series
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321047
6208-000-000
6298-000-000
2108 Aggressive Tooth Blades
ForUseWith:
Heavy Duty Sagittal Blades
2108-218-000 mm 25.0 1.24 1.24 98.5
No Offset inch .98 .049 .049 3.88 12
2108-309-000 mm 21.0 .89 .89 84.5
No Offset inch .82 .035 .035 3.32 12
2108-305-000 mm 25.0 .89 .89 73.0
No Offset inch .98 .035 .035 2.88 12
2108-302-000 mm 25.0 .89 .89 89.5
No Offset inch .98 .035 .035 3.53 12
Blade Mount
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 48
6208-000-000
6298-000-000
2108 Aggressive Tooth Blades
ForUseWith:
Heavy Duty Sagittal Blades
2108-351-000 mm 25.0 1.19 1.19 85.0
No Offset inch .98 .047 .047 3.34 12
2108-328-000 mm 25.0 1.24 1.24 98.5
No Offset inch .98 .049 .049 3.88 12
2108-318-000 mm 25.0 1.24 1.24 79.5
No Offset inch .98 .049 .049 3.13 12
2108-310-000 mm 25.0 1.24 1.24 73.0
No Offset inch .98 .049 .049 2.88 12
Blade Mount
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 321049
6208-000-000
6298-000-000
2108 Aggressive Tooth Blades
ForUseWith:
Heavy Duty Sagittal Blades
2108-377-000 mm 25.0 1.32 1.32 86.5
No Offset inch .98 .052 .052 3.41 12
2108-376-000 mm 25.0 1.47 1.47 79.0
No Offset inch .98 .058 .058 3.13 12
2108-356-000 mm 12.5 1.24 1.24 79.0
No Offset inch .49 .049 .049 3.13 12
2108-352-000 mm 12.5 1.19 1.19 81.5No Offset inch .49 .047 .047 3.20 12
2108-382-000 mm 18.5 1.24 1.24 83.5
No Offset inch .73 .049 .049 3.29 12
Blade Mount
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 50
6208-000-000
6298-000-000
ForUseWith:
2108-389-000 mm 25.0 1.27 1.27 81.5No Offset inch .98 .050 .050 3.20 12
2108-385-000 mm 18.5 1.24 1.24 104.0No Offset inch .73 .049 .049 4.10 12
2108-383-000 mm 29.0 1.24 1.24 83.5No Offset inch 1.14 .049 .049 3.29 12
Blade Mount
Heavy Duty Sagittal Blades
2108 Aggressive Tooth Blades
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
2108-393-000 mm 25.0 1.04 1.04 81.5No Offset inch .98 .041 .041 3.20 12
Stryker Customer Service 800 253 321051
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
2108-351-002 mm 25.0 1.19 1.19 95.0
No Offset, Aggressive inch .98 .047 .047 3.76 12
2108-376-002 mm 25.0 1.27 1.27 91.5
No Offset, Aggressive inch .98 .050 .050 3.61 12
Blade Mount
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108 Special Conversion Aggressive Tooth Blades
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 52
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
No Offset, Aggressive
2108-382-002 mm 18.5 1.37 1.37 89.0No Offset, Aggressive inch .73 .054 .054 3.52 12
2108-382-003 mm 18.5 1.27 1.27 90.5No Offset, Aggressive inch .73 .050 .050 3.57 12
2108-383-002 mm 25.4 1.27 1.27 114.0No Offset, Aggressive inch 1.00 .050 .050 4.49 12
Blade Mount
2108 Special Conversion Aggressive Tooth Blades
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
HeavyDuty5
4208-000-000
2108-382-001 mm 18.6 1.32 1.32 90.5No Offset, Aggressive inch .73 .052 .052 3.57 12
Stryker Customer Service 800 253 321053
6208-000-000
6298-000-000
ForUseWith:
Heavy Duty Sagittal Blades
No Offset, Aggressive
Blade Mount
2108 Special Conversion Aggressive Tooth Blades
Cut Material Cutting Cut TeethProduct and Part Number Edge Thickness Thickness Depth per inch
2108-393-006 mm 25.0 .97 .97 90.5No Offset, Aggressive inch .98 .038 .038 3.57 12
5301-110-051 mm 32.0 .61 .94 62.9Offset inch 1.26 .024 .037 2.48 18
2108-393-005 mm 25.0 .97 .97 89.5No Offset, Aggressive inch .038 .038 .038 3.53 12
HeavyDuty5
4208-000-000
Stryker Customer Service 800 253 3210 54
6208-000-000
6298-000-000