cv dprasetya 2012

Curriculum Vitae – Diana Budi Prasetya

CV Dprasetya 2012.doc.doc of 5

PPPPERSONALERSONALERSONALERSONAL DDDDETAILSETAILSETAILSETAILS

Name : Diana Budi Prasetya

Sex : Male

Place/Date of Birth : Madiun/June 16th, 1980

Home Address : Jl. Wonokusumo Jaya I/131 Surabaya – 60153

Phone : Home – 031 3733027, Mobile – 0813 5770 7046

Email Address : [email protected]

Hobbies : Outbound, Traveling, Sports (Badminton, Football), Reading, Singing. FFFFORMAL ORMAL ORMAL ORMAL EEEEDUCATIONALDUCATIONALDUCATIONALDUCATIONAL HHHHISTORIESISTORIESISTORIESISTORIES

University : Bachelor Degree (S1) of Sepuluh Nopember Institute of Technology (ITS) of Surabaya,

Department of Mechanical Engineering, Faculty of Industrial Technology (1998-2004)

Specialization : Mechanical Design, Vibration & Maintenance

GPA : 3.15 (Scale 4)

Advisor : Yusuf Kaelani, Ir., MSc.E and (Alm.) Moh. Maksum Hadi, Ir., MSc., PhD

KKKKEYEYEYEY EEEEXPERIENCESXPERIENCESXPERIENCESXPERIENCES

Has more than 5 years solid experience as a Design Engineer (last post as Senior & Lead Engineer) starting from

Research and Development stage, Tendering, Engineering, Quality and Procuring processes in the specialty of

� Civil/Structural Engineering

o To design and analysis of Boiler steel structure and pressure vessel’s support according to numerous

international and local design codes/standards, i.e. AISC, EC3, BS 5950, SNI, AS 4100, etc.; seismic and

wind design of structures using STAAD Pro including to provide foundation load of structures for civil

works and design of base plates and anchor bolts, steel connection (simple shear & moment connection);

strong knowledge in material selection per ASME, ASTM, JIS, British and Euro material, GB (Chinese);

design and analysis of steel chimneys/stacks according to ASME STS-1, BS 4076 & CICIND; design of

silencer support steel and canopies, access platforms, stair tower; preparing Bill of Materials and

selections sheets; to review and approval of engineering deliverable documents of suppliers for supplied-

products & services; etc.

� Pipeline Engineering

o To design and analysis (pipe stress analysis) of high pressure & temperature BP, BEP & NBEP piping

according to ASME I, B31.1 & EN 13480 using AutoPIPE and CAESAR II including design of pipe

support and spring selection, design of welded attachments; strong knowledge in material selection per

ASME, ASTM, JIS, British and Euro material, GB (Chinese); design and analysis of safety/relieve valve

piping; piping flanges and valves selection; transfer pump selection; recommending the pipeline layout to

3D modeler; familiar with PDMS, Naviswork and a 3D model interference checking procedure to verify

a clashed-free pipeline layout; to review Bill of Material and piping isometric drawing, to review and

approval of engineering deliverable documents of suppliers for supplied-products & services; etc.

� Boiler/Pressure Vessel and its ancillaries

o To define the specifications of Boiler heat exchanger, flue gas ducts, expansion joints and other misc.

boiler equipment, i.e. flue gas and vent silencers, steam condensate drainage and tank (blow down tank

per ASME VIII); design and analysis of pressure vessel’s attachments/nozzles local stress &

reinforcements, heat exchanger’s support, etc.; design and analysis of drum saddle; strong knowledge in

material selection per ASME, ASTM, JIS, British and Euro material, GB (Chinese); preparing

mechanical design parameters to determine mechanical loadings for structures, piping and equipments,

i.e. wind, seismic, dead load, live load, thermal, rain and snow load per Euro code, ASCE, SNI, UBC,

IBC, British Standards, etc.; design and analysis of shipping, lifting and erection structures/frames;



providing erection procedure; preparing Bill of Materials and selections sheets; to review and approval of

engineering deliverable documents of suppliers for supplied-products & services; etc.

Also has the knowledge in Project Quality Engineering (current post as Project Quality Engineer) with main

knowledge

� To perform the overall coordination and administration of quality activities on specific contracts or customer

purchase order, developing the quality plan, participation on the project team, executing the quality plan

including surveillance, and quality records; to arrange the delivery of any required quality records to the

customer; attendance at Project Team meetings to communicate quality issues and report status; to represent and

provide the liaison with other quality operations activities; handling, processing and reviewing/approving of

supplier-submitted quality related documents as required and ensure the compliance to contract specifications

and requirements i.e. Inspection and Test Plan (ITP), Quality Manual, Certified Material Test Report, Testing

Procedures (Destructive & Non-Destructive Examination of welding, WPS, PQR, Hydrostatic Test, Assembly,

Functional Test, Coating & Painting, etc), Testing Reports including the specifications of the acceptance criteria

according to ASTM, AWS, ASME or local/customer regulations, etc.; to coordinate and participate in customer

surveillance at suppliers; to record the supplier non-conformances report (NCR); to coordinate Design Code

Quality activities for the project including arranging review of design calculations with the Authorized Inspector

(AI), overview the receipt and review of ASME P-4 form, transmitting the ASME Master Data Report to site,

verify the completeness and accuracy of the Master Data Package and nameplate, ASME stamp while the AI

witnesses.

� To compile and report all project quality issues (Cost of Poor Quality / COPQ) for further evaluation and lesson-

learned record for future projects quality awareness and send the report to Project Director and distribute to the

related departments (Engineering, Project Management, Sales & Tendering, Procurement & Logistics, R&D).

� To prepare a cost estimate for the quality issues and activities for proposal input at Tendering stage.

� To participate and act as internal auditor for Business Management process improvement and Quality

Management System.

� To perform an Audit for New Supplier Qualification concerning the Quality Program and EHS assessment.

� To enhance and coordinate all quality and process improvement programs within the company including EHS,

5S, Six Sigma, Continually Improvement Programs, Small Group Discussion, etc.

PPPPROJECTROJECTROJECTROJECT EEEEXPERIENCESXPERIENCESXPERIENCESXPERIENCES

1. Project: Package Boiler of Cilacap UP IV (2006), Client: PT Pertamina Indonesia.

2. Project: GE7F Combined Cycle Heat Recovery Steam Generator (2006), Client: SNC-Lavalin & TransCanada Energy

3. Project: GT26 Combined Cycle Power Plant (Once-Through Boiler) (2007), Client: Emland Lingen – Germany.

4. Project: GT26 Combined Cycle Single Shaft Heat Recovery Steam Generator (2007), Client: Aliveri METKA–Greece.

5. Project: GT26 Combined Cycle Single Shaft Heat Recovery Steam Generator (2008), Client: RWE Staythorpe – UK.

6. Project: Heat Recovery Steam Generator Standard Product Development behind GT26 & GT24 ALSTOM Gas

Turbines (2008-2009), International Assignment at ALSTOM Windsor-US.

7. Project: Heat Recovery Steam Generator Large, 50 & 60 cycle Standard Product Development (2009-2010)

8. Project: Combined Cycle Power Plant (2010-2011), Client: Keppel Merlimau Cogen Pte Ltd Singapore.

9. Project: Combined Cycle Power Plant (2011-2012), Client: Tuas CCP5 and SembCorp Banyan Ltd Singapore.

10. Six Sigma Project: Reducing Cost of Poor Quality on HRSG Secondary Steel Fabricated Components Problem.

Scope: (Project Lead). Cost Saving: USD 110,000. Client: ALSTOM

11. Six Sigma Project: Reducing The Overrun Cost on Estimating Budget between Tendering & Project Stage.

Scope: (Project Lead). Cost Saving: USD 110,000. Client: ALSTOM

12. Six Sigma Project: Logistics Cost Reduction Through Stuffing Capacity Optimization.

Scope: (Project Lead). Cost Saving: MUSD 2.68. Client: LG Electronics Indonesia.

13. Design and Build of New Compressors Building Combined with 3 mT Capacity of Maintenance Monorails (Linde).

14. Additional 6 NPS Piping System Tie-in to Existing 30 NPS Piping System (Linde).

15. CNG Refueling Station (Facility, Transmission Pipeline, Civil Work, Fire Protection System & Safety (Linde).

16. Design of Maintenance Monorail Beams and Lifting Lugs for 20 mT Waukesha Gas Engine (Linde).



WWWWORKING ORKING ORKING ORKING EEEEXPERIENCESXPERIENCESXPERIENCESXPERIENCES 1. PT ALSTOM Power Energy Systems Indonesia.

� Mechanical Design Engineer, Department of Engineering & Development (2006 – 2007)

� Mechanical Design Lead Engineer, Department of Engineering & Development (2007 – 2011)

� Mechanical Design Senior/Lead Engineer, Department of Engineering (2011)

� Mechanical Design Senior/Lead Engineer, Department of R&D (2011)

� Project Quality Engineer, Department of Quality & Process Improvements (January 2012 – Now)

� Six Sigma Green Belt

� Hands on experience in Six Sigma for Manufacture and Design for Six Sigma tools and techniques,

standardized work, scientific problem solving (PDCA), 5S, Voice of Customer, FMEA & DMAIC.

� Exceptional presentation and coaching skills.

� Run & lead Six Sigma projects and conduct effective team meeting to achieve Six Sigma project timeliness.

� Coordinate and deploy the implementation of Six Sigma improvement method to stake holders in reducing

Cost of Poor Quality (CoPQ), improving design cycle time and Material Cost Reduction.

� Align the Enterprise Business objective through Six Sigma projects.

2. PT LG Electronics Indonesia, R&D Mechanical Engineer, Department of R&D (2004 – 2006)

Job description: Developed new mechanical parts of TV and Monitor products using Pro Engineer 3D product

modeling software, created Bill of Materials for mechanical parts, issued Engineering Change Order (ECO), run &

supervised pilot product & 1st mass production (work with QC & Production depts.), established product quality

standards, created new product cost estimation, worked with Purchasing & Quality depts. for vendor approval,

involved and run Six Sigma projects (GB holder). OOOOTHERTHERTHERTHER RRRRESPONSIBILITIES/ESPONSIBILITIES/ESPONSIBILITIES/ESPONSIBILITIES/JJJJOB OB OB OB DDDDESCRIPTIONS ESCRIPTIONS ESCRIPTIONS ESCRIPTIONS AAAAS S S S SSSSENIOR/ENIOR/ENIOR/ENIOR/LLLLEAD EAD EAD EAD DDDDESIGNESIGNESIGNESIGN EEEENGINEER NGINEER NGINEER NGINEER AAAAT T T T AAAALSTOMLSTOMLSTOMLSTOM � Creates and review designs, procedures, selection sheets, Bill of Materials, calculations and drawings according to

customer’s specifications, company’s standards and relevant engineering international codes/standards on agreed

timeframes,

� Responsible for coordination and alignment of working methods, tools and systems,

� Contribute in the preparation of projects & support Tendering, as well as various R&D projects,

� Contribute actively in the quality control within the R&D and Engineering department,

� Report to the Manager and support with development, implementation and maintenance of business processes,

� Provide coaching and mentoring to Junior Engineers,

� Answer enquiries needed for a successful acquisitions process or project,

� Assist in the development and improvement of engineering tools and methods,

� Provide engineering advice and support to other disciplines as well as external parties, vendors and TFA (Technical

Field Assistant). If required, work with Site Manager at field for erection, installation and commissioning activities.

CCCCOMPETENCESOMPETENCESOMPETENCESOMPETENCES � Excellent leadership, communication, analytical and conceptual skills,

� Able to work independent and within a team,

� Safety awareness, HAZOP, Risk Management, 5S, FMEA.

� Proficiency in English and Bahasa, writing and communication,

� Calculation spreadsheets development.

� Problem solving methodology using Six Sigma.

� Visionary

� STAAD Pro, AutoPIPE, CAESAR II, RAM Connection, ProSteel, AutoCAD, Excel Spreadsheet, VBA, MS Ppt.,

ProE.



TTTTRAININGSRAININGSRAININGSRAININGS � Six Sigma Green Belt & Black Belt Level (Green Belt Holder), PT LG Electronics Indonesia (2005),

� Risk Management on HSE (Certified), PT LG Electronics Indonesia (2005),

� Standard Implementation for OHSAS 18001 & SMK3 (Certified), JAVAmitra Mandiri (2005),

� Internal Auditor for OHSAS 18001 & SMK3 (Certified), JAVAmitra Mandiri (2005),

� Procedure & Documentation for OHSAS 18001 & SMK3 (Certified), JAVAmitra Mandiri (2005)

� R&D Innovation Tools (Certified), PT LG Electronics Indonesia (2005),

� Supervisory Management Skills (Certified), HR Excellency (2005),

� English Course – Level IV (Certified), LIA (2008),

� Leadership (Certified), Dale Carnegie (2010),

� Managing Team, M-Knows (2011).

� Six Sigma, PT ALSTOM Power Energy Systems Indonesia (2011).

WWWWORKING ORKING ORKING ORKING TTTTOOLSOOLSOOLSOOLS � Bentley STAADPro, Bentley RAM Connection, Bentley AutoPIPE, CAESAR II ver. 5.2,

� AutoCAD, ProSteel, Pro Engineer (Basic), SolidEdge (Basic)

� Familiar with Naviswork Freedom 2011 and PDMS

� Excel Spreadsheets and VBA,

� Microsoft Office (Word, Excel, PowerPoint),

� International Codes & Standards

� Six Sigma Methodology. CCCCURRENT URRENT URRENT URRENT &&&& EEEEXPECTED XPECTED XPECTED XPECTED SSSSALARYALARYALARYALARY

Current Salary: IDR 10 million (= USD 1,100) gross/month (excluding allowances)

Expected Salary: IDR 20 million (= USD 2,100) gross/month (excluding allowances), negotiable.



OOOORGANIZATION RGANIZATION RGANIZATION RGANIZATION MMMMAPAPAPAP

SURABAYA

MANAGING

DIRECTOR

HR

MANAGER

PROJECT

MANAGEMENT

MANAGER

ENGINEERING

MANAGER

QUALITY &

PROCESS

IMPROVEMENT

MANAGER

PROCUREMENT

& LOGISTICS

MANAGER

R&D

MANAGER

PROJECT ENG.

MANAGER

MECHANICAL

DESIGN ENG.

MANAGER

PERFORMANCE

DESIGN ENG.

MANAGER

DESIGN

GRAPHIC

MANAGER

SENIOR

MECHANICAL

DESIGN ENG.

SENIOR R&D

ENG.

PROJECT

QUALITY ENG.

Was here

Was here Current

position

cv dprasetya 2012

Documents