cylinder bore inspection
DESCRIPTION
Cylinder Bore Inspection. Engineering Research Center for Reconfigurable Manufacturing Systems. NCU (residual boring marks after honing of cylinders) detection requested by power train. Applicable scattering phenomenon observed in laboratory. - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/1.jpg)
1NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Cylinder Bore Inspection
Engineering Research Center for
Reconfigurable Manufacturing Systems
![Page 2: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/2.jpg)
2NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Project Background
• NCU (residual boring marks after honing of cylinders) detection requested by power train.
• Applicable scattering phenomenon observed in laboratory.
• Defect detection: Go/No-Go vs. conventional metrology.
Project Goal
• Detection of non clean-up (NCU) of residual boring marks after honing of cylinder bores.
• Cycle time of 20 seconds required.
![Page 3: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/3.jpg)
3NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Laser Scattering from Machined Surfaces
Laser light normally incident on a
machined surface is scattered
preferentially in a plane perpendicular
to the machining marks.
The physical phenomenon used to
distinguish between boring and honing:
![Page 4: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/4.jpg)
4NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Cylinder Surface
• Scatter, not just reflection.
• Different pattern for boring vs. honing.
• Direction of scattered laser light varies with boring vs. honing.
![Page 5: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/5.jpg)
5NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Probe Assembly
Laser Prism
Cylinder Surface
MirrorAperture
FiltersDetector
Slip Ring
![Page 6: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/6.jpg)
6NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Manufactured Probe
Laser Prism
MirrorDetector
Slip Ring
![Page 7: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/7.jpg)
7NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Typical Data
• Data collected with Labview• Plots generated with Matlab
NCU Detection Properly Honed
![Page 8: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/8.jpg)
8NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Honing Problem Detection
Different honing patterns at the top and bottom of the cylinder
Axial stripes along the cylinder wall.
![Page 9: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/9.jpg)
9NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Alternate Detectable Conditions
Coarse Honing Fine and Coarse Boring
![Page 10: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/10.jpg)
10NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Full Scale Prototype Goals
• Technology transfer to industry.• Demonstrate parallel probe operation.• Demonstrate survivability and maintainability
of probes in a factory environment.• Accelerate implementation in ERC member
company plants.
![Page 11: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/11.jpg)
11NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Full Scale Prototype Requirements
• Inspect one bank of V blocks, all cylinders of straight 4 blocks.
• Demonstrate parallel operation.• Easily reconfigurable.• Inspect blocks from different manufacturers-
straight 4,V-6, and V-8.• Minimum cost.
![Page 12: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/12.jpg)
12NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Machine Specifications
![Page 13: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/13.jpg)
13NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Prototype Layout as in the Request for Proposal (RFP)
Vibration absorbing pads
Motion stage
Probe rotation mechanism
Probes
Block
TableInspection station computer
Environmental shield
Base
Support structure
Fork lift holes
![Page 14: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/14.jpg)
14NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Full Scale Prototype Configuration as Requested by End-Users
![Page 15: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/15.jpg)
15NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Completed Prototype
• Station installed week of 9-17-07.• Station and probes are operational.
![Page 16: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/16.jpg)
16NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
System Communication
PC 5
PC 1 PC 2 PC 3 PC 4
Rotary encoder
Cylinder tool
Rotary encoder
Cylinder tool
Rotary encoder
Cylinder tool
Rotary encoder
Cylinder tool
Linear encoderGehring PC
Gehring machine head
UM system
![Page 17: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/17.jpg)
17NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Future Work
• Optimization of parallel detection at the ERC.• Factory implementation of prototype system.• Possible detection of rough hone or boring
stages. • A probe to measure dimensional variation
and detect NCU is being developed.
![Page 18: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/18.jpg)
18NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
A new probe is being developed.
Probe centering in a cylinder will be easily determined using this probe.
Probe uses different detector, electronics, optics and software.
New probe will measure dimensional variation as well as check surface finish.
![Page 19: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/19.jpg)
19NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Dimension sensing probe
• Scatter from surface is imaged onto detector by lens.• Image position changes with distance from probe to surface.• Detector is position sensitive.
Slip Ring
Bore Surface
MirrorLensDetector Laser
![Page 20: Cylinder Bore Inspection](https://reader036.vdocuments.net/reader036/viewer/2022081502/56815922550346895dc64b23/html5/thumbnails/20.jpg)
20NSF Engineering Research Center for Reconfigurable Manufacturing SystemsUniversity of Michigan College of Engineering
Questions?