d184s073u02 electromagnetic flowmeter...

Level 0: Information

Data SheetD184S073U02

Function– Electromagnetic flowmeters ca

measure the flowrate of liquids,sludges with an electrical condu(opt. 0.5 µS/cm).

Applications– The SM4000 is specially design

pulp & paper and food & beverato measure pulp stocksflows, faphase liquids, mining slurries anpump application).

Instrument Advantages– Digital Signal Processing (DSP)

and accuracy in both flow direcstability.

– Integrated diagnostic tools incluwith the error analysis displayedcontact output for increased op

– Easy to use menudriven operaapplication the configuration. Edisplay is backlighted.

Important Instrument Featu– flowmeter primary designed pe– diameter range from DN 1 to D– accuracy < ± 0.5 of rate– fluid temperatures 40 °C to 13– Hygienic Certification 3A, FML,– liners, PFA, PTFE, hard rubber – standardized installation lengths– Power supply voltage AC/DC

FieldIT

Electromagnetic Flowmeter FSM4000

n be used to accurately slurries, pastes and ctivity of at least 20 µS/cm

ed to measure liquids in the ge industry. It can be used st changing process, two d pulsating flows (piston

assures long term stability tions with absolute zero

ding system monitoring and signalled over a erational reliability.ting structure for asy to read the fullgraphic

resr PEDGuideline 97/23 ECN 1000 [1/25” to 40”]

0 °C (opt. 180 °C) EHEDG

for DIN or ANSI flanges

Electromagnetic Flowmeter FSM4000D184S073U02

Accuracy, Reference Conditions and Operating Principle

Reference Conditions per EN 29104

Fluid Temperature

20 °C ± 2 K

Ambient Temperature

20 °C ± 2 K

Supply Power

Nominal voltage per name plate UN ± 1 %

Reference installation conditions

Upstream > 10 x D, Downstream > 5 x D, D = nominal size of the flowmeter primary

Warm-up Time

30 min

Analog Output Effects

Same as pulse output plus ± 0.1 % of rate ± 0.01 mA

Operating PrincipleFaraday’s Laws of Induction form the basis for the electromagnetic flowmeters. It states that a voltage is induced in a conductor as it moves through a magnetic field.This principle is applied to a conductive fluid which flows through a magnetic field generated perpendicular to the flow direction (see Schematic).The voltage induced in the fluid is maesured at two electordes, installed diametrically opposed. This signal voltage UE is proportional to the magnetic induction B, the electrode spacing D and the average flow velocity v.Noting that the magnetic induction B and the electrode spacing D are constants, a proportionality exists between the signal voltage UE and the average flow velocity v. The equation for the volume flow shows that the signal voltage UE is linear and proportional to the volume flowrate.The induced signal voltage is processed in the converter into scaled, analog and digital signals.

0

0

5

0.5

10

1

20

2

90

9

100 %

10

Acc

urac

y

%

Q

mvs0.5

Range max

789

6

54321

0.5

Pulse Output Q> 0.05 Rangemax ± 0.5 % of rateQ< 0.05 Rangemax ± 0.00025 Rangemax

Fig. 1 Accuracy

UE

y

z

x

BD

E

v

Magnet Coil

Meter Tube inElectrode Plane

Signal electrode

Signal voltage

UE = Signal voltage B = Magnetic induction D = Electrode spacing v = Average flow velocity qv = Volume flowrate

UE ~

qv =

UE ~ qv

B D v⋅ ⋅

D2 π4

v⋅

Fig. 2 Electromagnetic Flowmeter Schematic

2


Overview, Flowmeter Primary and Converter Design

Weld stubs

Pipe fittingFood industry fitting

Tri-Clamp

External threads

Rigid Flanges Rigid FlangesWafer DesignVariable Connections

DN 3–DN 40 1/10”–11/2”

DN 50–DN 100 2”–4”

DN 3–DN 40 1/10”–11/2”

DN 50–DN 100 2” – 4”

Connection Types

Additional, see Dimensions, Others upon request

Accuracy 0.5 % of rateFlowmeter primary hsg. material Complete stainless steel housing Series 2000 Alum. Series 4000

Flowmeter PrimaryModel Number SE21* SE21F SE21W SE41F

Process Connections DN Inch PN * DN PN DN Inch PN PNWafer Design 3–100 1/104 – W – 3–50 1/102 10–40

65–100 21/2–4 10–16–

Flanged DIN 2501 3–100 1/10–4 – F 3–100 10–40 – DN3–DN1000 10–40Flanged ASME B16.5 3–100 1/104 – F 1/10”–4”150–300 CL/JIS 350 1/102 CL300/JIS

65100 21/24 CL150/JIS1/10”–40” CL150 1/10”–12” CL 300

Food Industry Fitting DIN 11851 3–40 1/101 1/2 40 S 50, 80 2, 3 16 S 65, 100 2 1/2, 4 10 S

– – –

Weld stubs DIN 11850 3–40 1/101 1/2 40 R 50, 80 2, 3 16 R 65, 100 2 1/2, 4 10 R

– – –

Weld stubs DIN 2463 3–40 1/101 1/2 40 Q 50, 80 2, 3 16 Q 65, 100 2 1/2, 4 10 Q

– – –

Weld stubs ISO 2037 25–40 11 1/2 40 P 50, 80 2, 3 16 P 65, 100 2 1/2, 4 10 P

– – –

TriClamp DIN 32676 3–50 1/102 16 T 65, 100 2 1/24 10 T

– – –

External threads ISO 228 3–25 1/101 10 E – – –1/8” Sanitary connectors 1–2 1/251/12 10 B – – –Liner PEEK, Torlon (<DN 3[1/10”])

PFA (>DN 2 [1/12”])PFA PFA Hard rubber, soft rubber,

PTFE, PFA, othersConductivity ≥ 20 S/cm Option ≥ 0.5 µS/cmElectrodes SST No. 1.4571 [316Ti], 1.4539, Hastelloy B2/C4, PlatinumIridium, Tantalum, TitaniumProcess connection material SST1.4404[316L] SST No. 1.4571 [316Ti] – Steel,SSTNo.1.4571[316Ti]Protection Class per EN 60529 IP 67/ IP 68 IP 67 / IP 68 IP 67/ IP 68 IP 67 / IP 68Fluid temperature 25 to 130 °C 40 to 130 °C 25 to 130 °C 25 to 130 °C / 180 °C

ApprovalsHygienic & sterile requirements CIP/SIPcapable FML, 3A, EHEDG CIPcapable

ConverterModel Number S4Supply power 85 – 253 V AC, 24 V AC/DCCurrent output standard 0/2–10 mA, 0/4–20 mAPulse output, 1channel std. active (24 V), optocoupler (220 mA)Ext. Zero return yesExt. Totalizer reset yesForward/reverse metering yesCommunication HARTProtocol® (PROFIBUS PA, FF in preparation)Fluid monitor std. yes, from DN 10 [3/8”] and ≥ 20 S/cmDetection empty pipe yesLocal indicator/totalizer yesAuto. density correction yes, manual entry (totalize and indicate in mass units)Protection Class / EN 60529 IP 67, NEMA 4XHousing Field mount housing

µ

µ

3


Specifications: Flowmeter Primary

Flow Ranges, Meter Sizes and Pressure Ratings

Information:

When a preamplifier is installed for low conditivity applications and the fluid has a high εr (e.g. demineralized water εr = 78) the fluid velocity is limited < 1 m/s.

Flange Designs and Pressure Ratings

Other meter sizes, press. ratings, temperature classes upon request.

Designs

Meter tube

Stainless steel No. 1.4301 [304]

DN 3 to DN 300 [1/10” to 12”]

Two piece housing: Cast Alum., painted1)

Flanges

Steel, zinc plated, standard Stn. stl 1.4571[316Ti] (≤ DN15[1/2”] standard)

DN 350 to DN 1000 [14” to 40”]

Steel, welded design, painted1)

Flanges

Steel, painted, standard,stn. stl. 1.4571[316Ti]

Connection Box

Body: RAL 70122)

Cover: RAL 90021)

1) Paint coat 80 µm thick, RAL 9002 (white grey), painting see page 8 2) Paint coat 80 µm thick, RAL 7012 (Basalt grey)

Meter Size

Dn Inch

Std. Pressure Rating

PN

Min. Flow RangeFlow Velocity0 to 0.5 m/s

Max. Flow RangeFlow Velocity0 to 10 m/s

1 1/25 1.5 1/17 2 1/12

101010

0 to 0.03 l/min 0 to 0.06 l/min 0 to 0.1 l/min

0 to 0.6 l/min 0 to 1.2 l/min 0 to 2 l/min

3 1/10 4 5/32 6 1/4

404040


0 to 4 l/min 0 to 8 l/min 0 to 20 l/min

8 5/16 10 3/8 15 1/2

404040


0 to 30 l/min 0 to 45 l/min 0 to 100 l/min

20 3/4 25 1

4040

0 to 7.5 l/min 0 to 10 l/min

0 to 150 l/min 0 to 200 l/min

32 11/440 11/2

4040



50 2 65 21/2 80 3

404040

0 to 3 m3/h 0 to 6 m3/h 0 to 9 m3/h

0 to 60 m3/h 0 to 120 m3/h 0 to 180 m3/h

100 4 125 5 150 6

161616

0 to 12 m3/h 0 to 21 m3/h 0 to 30 m3/h

0 to 240 m3/h 0 to 420 m3/h 0 to 600 m3/h

200 8 250 10 300 12

10/1610/1610/16

0 to 54 m3/h’ 0 to 90 m3/h 0 to 120 m3/h

0 to 1080 m3/h 0 to 1800 m3/h 0 to 2400 m3/h

350 14 400 16 450 18 500 20

10/1610/16Cl150

10

0 to 165 m3/h 0 to 225 m3/h 0 to 300 m3/h 0 to 330 m3/h

0 to 3300 m3/h 0 to 4500 m3/h 0 to 6000 m3/h 0 to 6600 m3/h

600 24 700 28 800 32

101010

0 to 480 m3/h 0 to 660 m3/h 0 to 900 m3/h

0 to 9600 m3/h 0 to 13200 m3/h 0 to 18000 m3/h

900 36 100040

1010

0 to 1200 m3/h 0 to 1350 m3/h

0 to 24000 m3/h 0 to 27000 m3/h

Meter Size Flanges Material Press. Rating PED

3 – 251/10” – 1”

DINASME

JIS

SS1.4571[316Ti]or Steel

40 barCL 150, CL 300

10 bar

SEPArt.3Par. 3

3211/4”

DINASME

JIS


40 barCL 150, CL 300

10 bar

Con

form

ity E

valu

atio

n pe

r C

ateg

ory

III, M

odul

e B

1 +

D, F

luid

Gro

up 140

11/2”DIN

ASMEJIS


40 barCL 150, CL 300

10 bar

502”

DINASME

JIS


40 barCL 150, CL 300

10 bar

6521/2”

DINASME

JIS


16, 40 barCL 150, CL 300

10 bar

803”

DINASME

JIS


40 barCL 150, CL 300

10 bar

1004”

DINASME

JIS


16, 40 barCL 150, CL 300

10 bar

1255”

DINASME


16, 40 barCL 150, CL 300

1506”

DINASME


16, 40 barCL 150, CL 300

2008”

DINASME


10, 16, 25, 40 barCL 150, CL 300

25010”

DINASME


10, 16, 25, 40 barCL 150, CL 300

30012”

DINASME


10, 16, 25, 40 barCL 150, CL 300

350 – 100014” – 40”

DINASME


10, 16, 25, barCL 150

4


Installation Length, Flanged (Short Design)

Meter sizes DN 10 – DN 400 [3/8”–16”] correspond to DIN/ANSI Flanged design VDE/VDI 2641 and the installation lengths defined in DVGW Working Paper, W420 f (Water Totalizers, Design WP ISO 4064 Short as well as ISO 13359).

ANSI CL 150/CL 300

With PFA, installation length, flanged to ISO 13359with PTFE, Hard/soft rubber Installation length, flanged to ISO 13359 or ABB (Installation length Series 1000)

Pipeline Vibrations

Max. allow. 15 m/s2 (10 – 150 Hz)

Temperature Diagram

60

50

10

0

130

Standard Flanges

Ambient Temperature °C

High Temperature Design

Stn. Stl. may be used for the entire range

180 Fluid Temp.°C

25

25

Note: Max. measuring temperature for hard/soft rubber ≤ 90 °C

Fig. 3 Fluid Temperature as a Function of the Ambient Temperature

Max. Allowable Cleaning Temperatures PTFE, PFA Designs

If the ambient temperature >25 °C, the difference must be subtracted from the max. cleaning temperature. Tmax – ∆ °C. ∆ °C = (TAmb. 25 °C [13 °F])

Weight

See Dimensions

Min. allowable Pressure and Fluid Temperature

Other meter sizes, pressure ratings and Temperature Classes upon request

Material strength for Model SE41F

Attention:

Limits for the allowable fluid temperature (TS) and allowable pressure (PS) are a function of the liner and flange materials of the flowmeter (see instrument Name Plate).

Material Strength Curves

Liner: PTFE, hard/soft rubber (limited to 90 °C, 194 °F)



CIPCleaning LinerPrimary

Tmax °C tmaxMinutes

TAmb. °C

Steam cleaning PTFE, PFA,PEEK, Torlon

150 60 25

Liquid cleaning PTFE, PFA,PEEK, Torlon

140 60 25

Liner material Meter size TOperationmbar abs

at TOperation

DN inch °C °FHard rubber 15 – 1000 1/2–40 0 < 90 < 194Soft rubber 50 – 1000 2–40 0 < 90 < 194PTFE 10 – 600 3/8–24 270

500< 20< 130

< 68< 266

PFA 3 – 100 1/10–4 0 < 130 < 266

Temperatur / Temperature (TS) [°C]

Dru

ck /

Pre

ssur

e (P

S) [

bar]

High temperature range

PN 40

PN 25

PN 16

PN 10

0

5

10

15

20

25

30

35

40

45

-30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120130140150160170180190

Fig. 4 DINFlanges SST No. 1.4571[316Ti] to DN 600 [24”]


Dru

ck /

Pre

ssur

e (P

S) [

bar]

300lb

150lb


0

5

10

15

20

25

30

35

40

45

50

55

-30 -10 10 30 50 70 90 110 130 150 170 190

psi

0

72.5

145

217.5

290

362.5

435

507.5

580

652.5

725

797.5

-22 °F 14 °F 50 °F 86 °F 122 °F 158 °F 194 °F 230 °F 266 °F 302 °F 338 °F 374 °F

0.01 bar = 1 kPa

Fig. 5 ANSIFlanges SST No. 1.4571[316Ti] to DN 600 [24”]

PN 40

PN 25

PN 16

PN 10


Dru

ck /

Pre

ssur

e (P

S) [

bar]


0

5

10

15

20

25

30

35

40

45

-30 -10 10 30 50 70 90 110 130 150 170 190

Fig. 6 DINFlanges Steel to DN 600 [24”]

5



JIS 10K-B2210 Flanges SS No. 1.4571 [316Ti] or Steel

Liner: PTFE, hard/soft rubber (limited to 90 °C)

Liner: Hard/soft rubber ≤ 90 °C (≤194 °F)

Liner: Hard/soft rubber ≤ 90 °C (≤194 °F)

Specifications: Stainless Steel Flowmeter Primaries, Model SE21_, DN 1 to DN 100 [1/25“ to 4“]

Connection Overview Series 2000

Material Strength Curves for Flanged Flowmeters Model SE21F

Liner: PFA

Meter SizeDN Inch

Material PN TS [°C] PS [bar]

32–100 11/4 4 SST 1.4571[316Ti] 10 25 to +180 10

32–100 11/4 4 Steel 10 10 to +180 10

300lb

150lb

P/T-Ratings


Dru

ck /

Pre

ssur

e (P

S) [

bar

]

HochtemperaturbereichHigh temperature range

0

5

10

15

20

25

30

35

40

45

50

55

-30 -10 10 30 50 70 90 110 130 150 170 190

psi

0

72.5

145

217.5

290

362.5

435

507.5

580

652.5

725

797.5

-22 °F 14 °F 50 °F 86 °F 122 °F 158 °F 194 °F 230 °F 266 °F 302 °F 338 °F 374 °F

0.01 bar = 1 kPa

Fig. 7 ANSIFlanges Steel to DN 600 [24”]

6

7

8

9

10

11

12

13

14

15

16

17

DN 700 PN 16

DN 900 PN 16DN 800 PN 16

DN 1000 PN 16

DN 900 PN10DN 800 PN 10DN 700 PN 10

DN 1000 PN 10


Dru

ck /

Pre

ssur

e (P

S) [

bar]

-30 -20 -10 0 10 20 30 40 50 60 70 80 90

Fig. 8 DINFlange SST No. 1.4571 [316Ti] DN 700 [28“]−DN 1000 [40”]

DN 700 PN 16

DN 900 PN 16DN 800 PN 16

DN 1000 PN 16

DN 900 PN 10DN 800 PN 10DN 700 PN 10

DN 1000 PN 10


Dru

ck /

Pre

ssur

e (P

S) [

bar]

6

7

8

9

10

11

12

13

14

15

16

17

-10 0 10 20 30 40 50 60 70 80 90

Fig. 9 DINFlanges Steel DN 700 [28“]−DN 1000 [40”]

Model: SE21

B E T R Q P S F W

Met

er S

ize

P

roce

ss C

onne

ctio

ns

1/8“

San

itary

Con

nect

ors

Ext

erna

l Thr

eads

TriC

lam

p D

IN 3

2676

Wel

d S

tubs

D

IN 1

1850

Wel

d S

tubs

D

IN 2

463

Wel

d S

tubs

IS

O 2

037

Food

Indu

stry

Fitt

ing

DIN

118

51

Flan

ge

Waf

er D

esig

n

DN 1 1/25” x PED

DN 2 1/12” x

SE

PA

rt. 3

,P

ar. 3

DN 3 1/10” x x x x x x

DN 4 5/32” x x x x x x

DN 6 1/4” x x x x x x

DN 8 5/16” x x x x x x

DN 10 3/8” x x x x x x

DN 15 1/2” x x x x x x

DN 20 3/4” x x x x x x

DN 25 1” x x x x x x x

DN 32 11/4” x x x x x x

Con

form

ity.

Eva

luat

ion

per

Cat

egor

y III

Mod

ule

B1+

D, F

luid

Gro

up 1

DN 40 11/2” x x x x x x

DN 50 2“ x x x x x x

DN 65 21/2” x x x x x x

DN 80 3” x x x x x x

DN 100 4“ x x x x x x


Dru

ck /

Pre

ssur

e (P

S) [

bar] PN 40

PN 25

PN 16

PN 10

0

5

10

15

20

25

30

35

40

45

30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120130 *)

Fig. 10 DINFlanges SS 1.4571 [316Ti] to DN 100, 4“

6


Liner: PFA

Material Strength Curve for Wafer Design Model SE21W

Liner: PFA

JIS 10K-B2210 Wafer Design

*) Higher temperature are allowed for CIP/SIP cleaning for limited time periods, see Table „Maximum Allowable Cleaning Temperature“

Ambient Conditions

Ambient Temperature

25 °C to + 60 °C [13 °F to +140 °F]

Fluid Temperature DN 3−100

40 °C to +130 °C, CIPcapable, see Temperature Diagram and max. allowable cleaning temperature.The maximum allowable ambient temperature as a function of the fluid temperature for stainless steel process connections and the Wafer Design

Fluid Temperature DN 1−2 [1/25”−1/12”]

10 °C to +120 °C [14 °F to 248 °F], CIPcapable to max. 120 °C.

Storage Temperature

25 °C to +70 °C [13 °F to +158 °F]

Minimum Allowable Absolute Pressure

Maximal Allowable Fluid Temperature and Pressure

Process Connections

DN 1−2 [1/25”−1/12”]

1/8“Sanitary connectors with 2 grounding electrodes in the same material as the signal electrodes, standard

DN 3−100 [1/10”−4”]

Wafer Design, TriClamp, Food Industry Fittings, External threads. Others upon request

Meter SizeDN

Material PN TS [°C] PS [bar]

32–10011/4” 4”

1.4404[316L]1.4435[316L]1.4301[304]

10145 psi

40 to +13040 to +266 °F

10145 psi


Dru

ck /

Pre

ssur

e (P

S) [

bar] 300lb

150lb

0

5

10

15

20

25

30

35

40

45

50

55

30 10 10 30 50 70 90 110 130 *)

Fig. 11 ANSIFlanges SS 1.4571 [316Ti] to DN 100, 4“

P/TRatings


Dru

ck /

Pre

ssur

e (P

S) [

bar]

PN 40/CL 300

PN 25

PN 16/CL 150

PN 10

0

5

10

15

20

25

30

35

40

45

60 50 40 30 20 10 0 10 20 30 40 50 60 70 80 90 100110120130*)

40 22 4 14 32 50 68 86 104 122 140 151 176 194 212 230 248 266 284 °F

psi

0

72.5

145

217.5

290

362.5

435

507.5

580

652.5

Fig. 12

Liner Meter SizeDN Inch

POperatembar abs

at TOperate°C

PFA 3–100 1/104 0 ≤ 130*)Peek/Torlon 1–2 1/251/12 0 ≤ 120

Process Connections Liner PFA

Meter SizeDN Inch

PSbar

at TS°C

Wafer Design 3–50 1/10−265–100 21/2−4

4016

≤≤

130*)130*)

Weld stubs 3–40 1/10−1 1/250, 80 2, 3 65, 100 2 1/2, 4

401610

≤≤≤

130*)130*)130*)

TriClamp 3–50 1/10−265–100 2 1/2−4

1610

≤≤

121121

Food Industry fittings 3–40 1/10−1 1/250, 80 2, 3 65, 100 2 1/2, 4

401610

≤≤≤

130*)130*)130*)

External threads 3–25 1/10−1 10 ≤ 130*)1/8”Sanitary connectorsLinerPeek/Torlon

1–2 1/25−1/12 10 ≤ 120

0

60

25

40 130 *)FluidTemp. °C

Ambient Temperature °C

50

Fig. 13 Temperature Diagram

7


Maximal Allowable Cleaning Temperature

If the ambient temperature >25 °C, the difference must be subtracted from the max. cleaning temperature. Tmax °C, °C = (TAmb. 25 °C) [13 °F].

Maximal Allowable Temperature Shock

Specifications Flowmeter Primary

Flowmeter Primary Materials

Protection Class

IP 67 Standard IP 68 with connector Pg 13.5 and PU resin compound

Pipeline Vibration

Maximum allowable 15 m/s2 (10−150 Hz)

Specification for painting

Type of painting

Epoxy powder coating

Priming coat

No priming coating

Preparing of the surface

Cleaning in a high alkaline bath, Alodine procedure conversion layer for a better adherion of the painting

Thickness of painting

80 µm

Color

RAL 9002 (White grey)RAL 7012 (Basalt grey)

CIPCleaning Liner Tmax°C

TmaxMinutes

TAmb°C

Steam Liquid cleaning

PFA/PeekPFA/Peek/Torlon

150140

6060

2525

Liner Temp.Shockmax. Temp.Diff. °C

Temp.Gradient°C/min

PFA, Peek, Torlon arbitrary arbitrary

Liner Materials

Electrode Materials Electrode DesignStandard Others Standard Others

PFA, Peek, Torlon

Hast.C4 (1.4539 for Food Ind. fittings and TriClamp)

Hast.B2 SST 1.4539 SST 1.4571[316Ti] Tantalum, Titanium, PlatinumIridium

Flat head Conical head (≥ DN10 [3/8”]) SST No. 1.4539

Process Connection Materials

Standard Option

Flange SST 1.4571 [316Ti] upon req.Wafer Design noneWeld stubs SST 1.4404 [316L] upon req.Food Ind. fittings SST 1.4404 [316L] upon req.TriClamp SST 1.4404 [316L] upon req.External threads SST 1.4404 [316L] upon req.1/8”Sanitary connectors SST 1.4571 [316Ti] POM, Brass, PVCConnection Box Stainless Steel –Meter tube SST 1.4301 [304] –Cable connector Polyamide PVDFPrimary housing Deep drawn housing SST No. 1.4301[304]

Process Connection Material Gasket MaterialsWafer Design, noneWeld stubs, Food Ind. fittingTriClampExternal threads

EPDM (EthylenePropylene) std. with FDAApproval (CIP capable, no oil or grease) Silicone with FDAApproval (option, suitable for oil and grease)

Flat housing gaskets Silicone (suitable for oil and grease)

∆ ∆

8


Specifications: Flowmeter Primary, Flowrate NomographsFlowrate Nomograph

Flowrate Nomographs

The volume flowrate is a function of the flow velocity and the flowmeter size. The Flowrate Nomographs, Fig. 14 and Fig. 15 indicate the flowrate range for a specific flowmeter size and which flowmeter sizes are suitable for a specific flowrate.

Example:

Flowrate = 7 m3/h (Maximum value = range end value). Suitable are flowmeter sizes DN 20 to DN 65 [3/4” to 2/12”] for a flow velocity between 0.5 and 10 m/s.

l/min l/s3/hm

54

3

2

103

102

8

654

3

2

Exam

ple

8

654

3

2

10-1

108

654

3

8

654

3

2

2

1

8

654

3

2

8

654

3

2

8

654

3

2

8

654

3

10-1

10-2

10-3

108

654

3

2

18

654

3

2

8

654

3

2

DN 100

DN 80

DN 65

DN 50

DN 40

DN 32

DN 25

DN 20

DN 15

DN 10

DN 8

DN 6

DN 4

DN 3

DN 2

DN 1.5

DN 1

32 4 5 6 8 1010.80.60.5m/s

10-3

10-1

10-2

8

654

3

2

8

654

3

2

8

654

3

2

1

108

654

3

2

102

8

654

3

2

3

2

Fig. 14 Flowrate Nomograph DN 1 to DN 100 [1/25” to 4”]

l/min 3/hm l/s

103

8

6

54

3

2

108

6

54

4

3

3

2

2

108

6

54

3

2

4

5

104

8

654

3

3

2

2

103

8

654

3

2

10

108

654

3

2

2

32 4 5 6 8 1010.80.60.5m/s

108

654

3

2

8

654

3

2

10

3

8

654

3

2

10

654

3

2

DN 250DN 300DN 350DN 400

DN 500DN 600DN 700DN 800DN 900DN 100

0

DN 125DN 150

DN 200

DN 450

Fig. 15 Flowrate Nomograph DN 125 to DN 1000 [5” to 40”]

9


Specifications: Flowmeter Primary, Installation Requirements and GroundingUp- and Downstream Straight Sections

Flowmeter installation is the key to an accurata flow measurement system. As a rule of thump, generally 3 pipe diameters uystream and 2 pipe diameters downstream are sufficient. Other upstream obstructions however, such as double elbows out of plane, control valves and nonconcentric pipe reducers etc. may require longer lengths.

Grounding

Grounding the flowmeter primary is necesary not only for safety reasons but also to assure proper opration of the electromagnetic flowmeter. The grouding screws on the flowmeter primary, which correspond to VDE 0100, Part 540, are to be connected to earth potential. For measurement reasons this potential should be identical to the fluid potential if at all possible.In applications using plastic or insulating lined pipelines the ground connections are made utilizing grouding plates or grounding electrodes. If stray currents are present in the pipeline, grounding plates up and downstream of the flowmeter primary are recommended.

Electrode Axis

Neither electrode should be positioned at the highest pont in the pipeline in horizontal installations. Gas bubbles, which may be present in the fluid, could interrupt the electrical connection between the electrodes and the fluid. An ideal installation is shown in Fig. 16. Assure that the meter tube is always completely filled with fluid. Instrument designs with removable electrodes for cleaning are available upon request.

Installations in Larger Size Pipelines

The flowmeter can be installed in larger size pipelines without problems using reducer sections. The pressure drop when reducers are used can be determined from the Nomograph Fig. 17. The procedure for determining the pressure drop is as follows:1. Determine the diameter ratio d/D.2. Calculate the flow velocity as a function of the flowmeter size

and the flowrate:

v =

The flow velocity can also be determined from the Flowrate Nomographs, Fig. 14 and Fig. 15.

3. In Fig. 17 read the “Pressure drop” value, yaxis, at the intersection of the “Diameter Ratio”, xaxis, and the “Flow Velocity” curve.

Electrode Axis

Fig. 16 Electrode Axis

Q (flowrrate)Primary Constant----------------------------------------------

D d

8°

Flanged Reducer

100

10

1

0.5 0.6 0.7 0.8 0.9

v=8m/s

7m/s

6m/s

5m/s

4m/s

3m/s

2m/s

d = EMF inside diameter D = Pipe inside diameter v = Flow velocity in m/s ∆p = Pressure drop in mbar

Pressure Drop Nomograph for EMF Flanged reducers with α/2 = 8°

Diameter Ratio d/D

Pre

ssur

e D

rop

∆p [m

bar]

Fig. 17 Pressure Drop Nomograph

10


Dimensions: Flowmeter Primary DN 3 to DN 300 [1/10“–12“], DIN Flanges

Model SE41F

1) Other pressure ratings upon request.2) Standard with one grounding plate mounted on one flange SST No. 1.4571 [316Ti]. Other materials upon request.

See also Information “Grounding”. DN 3–100 L + 3 mm, DN 125–300 L + 5 mm.3) With protection flanges. Protection flanges replace grounding plates. DN 3–100 L + 6 mm, DN 125–300 L + 10 mm.

Series 1000 (for replacement only) also available with protection flanges, Dimensions see page 16.4) For high temperature design + 120 mm.

Flange Dimensions Instrument Dimensions Weight

DN PN1) D/H d4 b k d2 N A L* L2) L3) E4) F G4) kg lb (pound)

3−8 10 15 20

10−4010−4010−4010−40

90 90 95105

40 40 45 58

18181820

60 60 65 75

14141414

4 4 4 4

67 67 67 87

130200200200

133203203203

136206206206

101101101112

62 62 62 73

129129129140

2.533

3.5

5.51 6.61 6.61 7.72

25 32 40

10−4010−4010−40

115140150

68 78 88

202020

85100110

141818

4 4 4

87 95100

200200200

203203203

206206206

112117121

73 78 82

140145149

456

8.82 11.02 13.23

50 10−40 165 102 21 125 18 4 116 200 203 206 129 90 157 8 17.64

65 10−1625−40

185185

122122

2125

145145

1818

4 8

100100

200200

203203

206206

153153

104104

171171

1212

26.45 26.45

80 10−40 200 138 27 160 18 8 100 200 203 206 159 110 177 16 35.27

100 10−1625−40

220235

158162

2327

180190

1822

8 8

130130

250250

253253

256256

179179

130130

197197

1515

33.07 33.07

125 10−1625−40

250270

188188

2529

210220

1826

8 8

124124

250250

255255

260260

170170

127127

195195

2330

50.71 66.14

150 10−1625−40

285300

212218

2531

240250

2226

8 8

170170

300300

305305

310310

190190

148148

216216

2834

61.73 74.96

200 1016

340340

268268

2828

295295

2222

812

195195

350350

355355

360360

222222

179179

248248

5454

119.05119.05

250 1016

395405

320320

3030

350355

2226

1212

250250

450450

455455

460460

250250

207207

276275

8080

176.37176.37

300 1016

445460

370378

3133

400410

2226

1212

250250

500500

505505

510510

293293

250250

318318

8392

182.98202.82

Projektion nach ISO Methode E

H

d2

k

Number of Holes N

Cable Connector M20 x 1.5

FE G

88

A b

L*

d4 D

Cable ConnectorM20 x 1,5

Number ofHoles N

All dim’s in mm

Tolerances L*

DN 3−200 1/10”−8”

+ 0

– 3

DN 250−300 10”−12”

+ 0

– 5

Fig. 18 Flowmeter Primaries DN 3 to DN 300 [1/10: to 12”]

11


Dimensions: Flowmeter Primary DN 3 to DN 300 [1/10“–12“], ANSI Flanges

Model SE41F

H

d2

k

Number of Holes N

Cable Connector M20 x 1.5

FE G

88

A b

L*

d4 D

88

Number ofHoles N

Cable ConnectorM20 x 1.5

35

d2

EF

G

k

1) Standard with one grounding plate mounted on one flange SST No. 1.4571[316Ti]. Other materials upon request. See also Information “Grounding”. DN 3–100 L + 3 mm, DN 125–300 L + 5 mm

2) With protection flanges. Protection flanges replace grounding plates. DN 3–100 L + 6 mm, DN 125–300 L + 10 mm Series 1000 ( for replacement only) also available with protection flanges, Dimensions see page 16.

3) For high temperature design + 120 mm.

MeterSize

Instrument Dimensions ANSI CL 150/CL 300 Flange Dimensions ANSI CL 150

Flange Dimensions ANSI CL 300

Weight

L1)2) *

DN Inch A ISO13359

ABB(Ser.1000)

E3) F G D/H d4 b k d2 N D/H d4 b k d2 N kgCL150/300

lb (pound)

3−810, 15

20 25

1/10−5/163/8, 1/2

3/41

67 67 87 87

130200200200

130270270270

101101112112

62 62 73 73

129129140140

89 89 99108

35 35 43 51

13131416

60 60 70 80

16161616

4 4 4 4

9595

117124

35 35 43 51

16161820

67 67 83 89

16161919

4 4 4 4

2.53

3.54

5.516.617.728.82

32 40 50

1 1/41 1/2

2

95100116

200200200

280280280

117121129

78 82 90

145149157

117127152

64 73 92

182021

89 99121

161619

4 4 4

134156165

64 73 92

212324

99115127

192319

4 4 8

568

11.0213.2317.64

65 80100

2 1/2 3 4

100100130

200200250

330340400

153159179

104110130

171177197

178191229

105127157

252626

140153191

191919

4 4 8

191210254

105127157

273034

150168200

232322

8 8 8

121615

26.4535.2733.07

125150200250

5 6 810

124170195250

250300350450

450450500550

169190222250

127148179207

195216248276

254279343406

186216270324

28303435

216241298362

22222225

8 8 812

280318381445

186216270324

39414753

235270330387

22222528

8121216

36/38386698

79/8483.77

145.50216.05

300 12 250 500 620 293 250 319 483 381 37 432 26 12 521 381 56 451 32 16 124/181 273/399

Tolerances L*

DN 3−200 1/10”−8”

+ 0

– 3

DN 250−300 10”−12”

+ 0

– 5

Projektion nach ISO Methode EAll dim’s in mm

Fig. 19 Flowmeter Primaries DN 3 to DN 300 [1/10: to 12”], ANSI Flanges

12


Dimensions: Flowmeter Primary DN 350 to DN 1000 [14“–40“], DIN Flanges

Model SE41F

A

d4

EG

F

L*

b

Cable Connector M20 x 1.5Number ofHoles N

kD

d4

d2

Tolerances L*

DN 350−500 14”−20”

0

– 5

DN 600−1000 24”−40”

0

– 10

1) Other pressure ratings upon request.2) One grounding plate mounted on one flange SST No. 1.4571[316Ti].

Other materials upon request. L + 5 mm.3) With protection plates mounted on both flanges, grounding plate not required L + 10 mm.

Series 1000 (for replacement only) also available with protection flanges, Dimensions see page 16.

DIN Flange Dimensions Instrument Dimensions Weight

DN PN1) D k d4 d2 N b A L * L2) L3) G E F appr. kg lb (pound)

350 350

1016

505 520

460 470

430 438

2226

1616

3135

322322

550 550

555 555

560 560

341341

313313

250250

126140

278 309

400 400

1016

565 580

515 525

482 490

2630

1616

3137

370370

600 600

605 605

610 610

367367

339339

275275

155175

342 386

500 500

1016

670 715

620 650

585 610

2633

2020

3339

407407

650 650

655 655

660 660

403403

375375

310310

191235

421 518

600 600

1016

780 840

725 770

685 725

3036

2020

3341

469469

780 780

785 785

790 790

454454

426426

361361

243302

536 666

700 700

1016

895 910

840 840

800 795

3036

2424

3541

537537

910 910

915 915

920 920

495495

469469

405405

315340

694 750

800 800

1016

10151025

950 950

905 900

3339

2424

3743

605605

10401040

10451045

10501050

545545

519519

455455

405467

8931030

900 900

1016

11151125

10501050

10051000

3339

2828

3945

671671

11701170

11751175

11801180

595595

569569

505505

483567

10651250

100010001000

61016

117512301255

112011601170

108011101115

303642

282828

313947

739739739

130013001300

130513051305

131013101310

645645645

619619619

555555555

475575764

104712681684


Fig. 20 Flowmeter Primaries DN 350 to DN 1000 [14” to 40”], DIN Flanges

13


Dimensions: Flowmeter Primary DN 350 to DN 1000 [14“–40“], ANSI Flanges

Model SE41F

Ad4

EG

F

L*

b

Cable Connector M20 x 1.5Number ofHoles N

kD

d4

d2

1) Other pressure ratings upon request.2) One grounding plate mounted on one flange SST No. 1.4571[316Ti].

Other materials upon request. L + 5 mm.3) With protection plates mounted on both flanges, grounding plate not required L + 10 mm.

Series 1000 (for replacement only) also available with protection flanges, Dimensions see page 16.

Meter Size Instrument Dimensions Flange Dimensions ANSI CL 150 1)

Weight

L2)3) * appr. kgCL150

appr. lb(pound)DN Inch A ISO

13359ABB

(ser.1000)E F G D k d4 d2 N b

350 400 450 500

14161820

322370407416

550600686762

650 700

– 780

313329375375

250275310310

341367403403

534 597 635 699

476 540 578 635

413 470 533 584

28.628.631.731.7

12161620

40424548

178 225 230 263

392496507580

600 700

2428

469537

914–

850 910

423469

361405

454495

813 837

749 749

692 762

34.934.9

2020

5350

327 385

721849

800 9001000

323640

605671739

–––

104011701300

519569619

455505555

545595645

94210571380

90010101210

864 9721140

22.225.456

484428

515763

513 6621132

113114592496

Tolerances L*

DN 350 –500 14”–20”

0

– 5

DN 600 –1000 24”−40”

0

– 10


Fig. 21 Flowmeter Primaries DN 350 to DN 1000[14” to 40”], ANSI Flanges

14


Ordering information: Flanged Instruments, Model SE41FIn addition to the Ordering Number please supply the following information: Fluid, fluid temperature, operating pressure, flow range, pipeline type (grounding plate, grounding electrodes)1)

Continued on next page1) If a grounding plate is required (see Part No.) The standard grounding plate is made of SST No. 1.4571[316Ti]. Others upon request.2) From DN 125 [5”] a conductive grounding surface is integrated in the hard/soft rubber liners, standard.3) For Food Industry applications.

Ordering Number SE41FLiner MaterialHard rubber (DN15DN1000 [1/2”40”]) KTW approved Soft rubber (DN50DN1000 [2”40”]) PTFE (DN10DN600 [3/8”24”]) FDA approved PFA (DN3DN 8 [1/10”5/16“”]) FDA approved Others

HSTPZ

Meter Size InchDN 3 1/10 DN 4 5/32 DN 6 1/4 DN 8 5/16

03040608

DN 10 3/8 DN 15 1/2 DN 20 3/4 DN 25 1

10152025

DN 32 11/4 DN 40 11/2 DN 50 2 DN 65 21/2

32405065

DN 80 3 DN 100 4 DN 125 5 DN 150 6

801H1Q1F

DN 200 8 DN 250 10 DN 300 12 DN 350 14

2H2F3H3F

DN 400 16 DN 450 18 (only ANSI Cl150/300 ISO 13359 Installation length) DN 500 20 DN 600 24

4H4F5H6H

DN 700 28 DN 800 32 DN 900 36 DN 1000 40

7H8H9H1T

Measuring Grounding Electrode Material 2)

SST No. 1.4571[316Ti] none Hastelloy B2 none Hastelloy C4 none standard Titanium none Tantalum none SST No. 1.45393) none PlatinumIridium none

SBHMTFP

SST No. 1.4571[316Ti] with Hastelloy B2 with Hastelloy C4 with Titanium with Tantalum with SST No. 1.45393) with PlatinumIridium with Others

ENOIQRGZ

Pressure RatingDIN PN 10 DIN PN 16 DIN PN 25 DIN PN 40

CDEF

JIS K10 ANSI CL 150 (Installation length Series 1000 only for replacement)ANSI CL 300 (Installation length Series 1000 only for replacement)ANSI CL 150 (ISO 13359 Installation length)ANSI CL 300 (ISO 13359 Installation length)Others

KPQRSZ

15


4) Only with Installation Length Series 1000 Short and ANSI/DINFlanges. Installation length ≤ DN 80[3] L + 20 mm, from DN 100[4”] L + 25 mm.

5) Notes on design

Max. cable lenght without preamplifier 50 mMax. cable lenght with preamplifier 200 m (Empty pipe detection not possible)

Additional Ordering Information may be provided in writing:

Name Plate (also available in Stainless Steel, option)

German EnglishFrench

Electrode Design

Standard Conical head (from DN 10 [3/8”] material SST No. 1.4539 used for high grease content fluids)

Ordering NumberFlange MaterialSteel (standard from DN 20[3/4”]) SS No. 1.4571[316Ti] (standard for DN3DN15[1/10”1/2”], option from DN 20[3/4”]) Others upon request

139

Flange AccessoriesNone Protection plates SST 1.4571[316Ti] (mounted one side) Grounding plate SST 1.4571[316Ti] (mounted one side) Protection flanges SST 1.4571[316Ti] (mounted both sides)4)

Only PTFE/PFA Only PTFE/PFA Only PTFE

ABCD

Temperature RangeStandard (see Specifications, Liner Materials) ≤ 130 °CHigh temperature design ≤ 180 °C (only PTFE/PFA)

SH

CertificationsNoneMaterial certified per EN 10204 Par. 3.1B and pressure test per AD2000Inspection Certificate EN 102043.1BPressure test per AD2000Others

ADFGZ

Calibration CertificatesStandardOthers

AZ

Protection Class per EN 60529IP 67 (connection box with M20 x 1.5 cable connector)IP 68 (connection box with M20 x 1.5 cable connector) and PU resin compoundIP 67 (connection box with NPTthreads)Others

2349

Design5)

Without preamplifier (Standard DN 10 [3/8“] to DN 1000 [4“])Preamplifier Typ A (Standard DN 3 [1/10“] to DN 8 [5/16“])Preamplifier Typ B

124

Design Minimum Conductivity

DN 3 [1/10“] to DN 8 [5/16“] DN 10 [3/8“] to DN 1000 [4“]

without preamplifier not possible = > 20 µS/cm

Preamplifier Typ A = > 20 µS/cm = > 5 µS/cm

Preamplifier Typ B = > 5 µS/cm = > 0,5 µS/cm

16


Dimensions: Stainless Steel Flowmeter Primaries DN 3 to DN 40 [1/10“ to 1-1/4“], Flanged

Model SE21F

103

L

A

FE

G

b

Dd4

83Cable ConnectorPg 13.5

Number of Holes N

41

kD

FE

G

d2

DIN Flange Dimensions

ANSI Flange Dimensions

1) If a grounding plate is required, L + 3 mm, materials upon request. With 2 grounding plates (protection plates) L + 6 mm, materials upon request.

Liner PFA WeightConnections DN PN L1) A D k d4 d2 b E F G appr. kg appr. lb

(pound)1/10−5/16“ 38

1040

130 37 90 60 42 14 18 108 62 134 3.5 7.723/8“, 1/2“ 10,15 200 37 95 65 36 14 18 108 62 134 3.5 7.72

3/4“ 20 200 42 105 75 41 14 20 120 66 136 3.5 7.721“ 25 200 54 115 85 54 14 20 127 73 143 4 8.82

1−1/4“ 32 200 62 140 100 64 14 20 132 78 148 5 11.021−1/2“ 40 200 67 150 110 74 14 20 136 82 152 5.5 12.13

Liner PFA WeightConnections DN PN L1) A D k d4 d2 b E F G appr. kg appr. lb

(pound)1/10”−5/16” 38

CL 150

130 37 88.9 60.3 42 15.9 18 108 62 134 3.5 7.723/8”, 1/2” 10,15 200 37 88.9 60.3 34.8 15.9 12.6 108 62 134 3.5 7.72

3/4“ 20 200 42 98.4 69.8 42.9 15.9 14.2 120 66 136 3.5 7.721“ 25 200 54 108 79.2 50.8 15.9 15.8 127 73 143 4 8.82

1−1/4“ 32 200 62 117.5 88.9 63.5 15.9 17.4 132 78 148 5 11.021−1/2“ 40 200 67 127 98.6 73.0 15.9 19 136 82 152 5.5 12.13

1/10”−5/16” 38

CL 300

130 37 95.2 66.7 42 15.9 18 108 62 134 3.5 7.723/8”, 1/2” 10,15 200 37 95.2 66.7 34.8 15.9 15.8 108 62 134 3.5 7.72

3/4“ 20 200 42 117.5 82.5 42.9 19 17.4 120 66 136 3.5 7.721“ 25 200 54 123.8 88.9 50.8 19 19.0 127 73 143 4 8.82

1−1/4“ 32 200 62 133.3 98.4 63.5 19 20.5 132 78 148 5 11.021−1/2“ 40 200 67 155.6 114.3 73.0 22.2 22.1 136 82 152 5.5 12.13


Fig. 22 Flowmeter Primaries DN 3 to DN 40 [1/10” to 11/2”]

17


Dimensions: Stainless Steel Flowmeter Primaries DN 50 to DN 100 [2“ to 4“], Flanged

Model SE21F

A

d2

L

EE

G

83

Cable Connector Pg 13.5

Number of Holes N

41

G

d4 D

b

DIN Flange Dimensions

ANSI Flange Dimensions

1) If a grounding plate is required, L + 3 mm, materials upon request. With 2 grounding plates (protection plates) L + 6 mm, materials upon request.

Liner PFA Weight

DN PN L1) A D k d4 d2 N b E G appr. kg appr. lb (pound)

50 10−40 200 100 165 125 104 18 4 24 135 161 8 17.64

65 10−1625−40

200200

107107

185185

145145

124124

1818

48

2626

149149

175175

1010

22.0522.05

80 10−40 200 107 200 160 139 18 8 28 155 181 12 26.45

100 10−1625−40

250250

159159

220235

180190

161167

1822

88

2428

175175

201201

1818

39.6839.68

Liner PFA Weight

Meter Size PN L1) A D k d4 d2 N b E G appr. kg appr. lb (pound)

2”

CL 150

200 100 152 121 99 19 4 23 135 163 8 17.64

2−1/2” 200 107 178 140 118 19 4 26 149 177 10 22.05

3” 200 107 191 152 131 19 4 28 155 183 12 26.45

4” 250 159 229 190 171 19 8 28 175 203 18 39.68

2”

CL 300

200 100 165 127 102 19 8 26 135 163 8 17.64

2−1/2” 200 107 191 149 124 22 8 29 149 177 10 22.05

3” 200 107 210 168 143 22 8 32 155 183 12 26.45

4” 250 159 254 200 177 22 8 36 175 203 18 39.68


Fig. 23 Flowmeter Primaries DN 50 to DN 100

18


Ordering Information: Stainless Steel Flowmeter Primaries DN 3 to DN 100 [1/10“ to 4“], FlangedIn addition to the Ordering Number please supply the following information: Fluid, fluid temperature, operating pressure, flow range, pipeline type (grounding plate)1)

Continued on next page1) Protection plates (2 grounding plates) mounted on both sides and grounding plate mounted on one side to flange,

material SST No. 1.4571 [316Ti]. Others upon request.

Ordering Number SE21F

Liner Material: PFA PMeter Size InchDN 3 1/10 DN 4 5/32 DN 6 1/4 DN 8 5/16 DN 10 3/8 DN 15 1/2 DN 20 3/4 DN 25 1 DN 32 11/4 DN 40 11/2 DN 50 2 DN 65 21/2 DN 80 3 DN 100 4

030406081015202532405065801H

Signal Electrode / Grounding Electrode MaterialSST No. 1.4571[316Ti] / none Hastelloy B2 / none Hastelloy C4 / none Titanium / none Tantalum / none SST No. 1.4539 / none (Food Ind. applications) PlatinumIridium / none

SBHMTFP

SST No. 1.4571[316Ti] / with Hastelloy Bs / with Hastelloy C4 / with Titanium / with Tantalum / with SST No. 1.4539 / with (Food Ind. applications) PlatinumIridium / withOthers

ENOIQRGZ

Pressure RatingPN 16 Standard DN 100 [4”] PN 40 Standard DN 3−80 [1/10”−3”]

DF

JIS K10 ANSI CL 150 (ISO 13359 Installation length) ANSI CL 300 (ISO 13359 Installation length)Others

KPQZ

Process Connection MaterialsSST No. 1.4571[316Ti] Others

39

Flange Accessories1)

NoneProtection Plates SST No. 1.4571 (mounted both sides)Grounding Plate SST No. 1.4571 (mounted one side)Others

ABCZ

Temperature RangeStandard design ≤ 130 °C (266 °F) S

19


In addition to the Ordering Number please supply the following information: Fluid, fluid temperature, operating pressure, flow range, pipeline type (grounding plate))1)

1) Notes on design





Electrode Design

Standard Conical head (from DN 10 [3/8”] material SST No. 1.4539 used for high grease content fluids)

Ordering Number SE21FCertificationsNoneMaterial certified per EN 10204 Par. 3.1B and pressure test per AD2000Inspection Certificate EN 10204 3.1BPressure test per AD2000Others

ADFGZ


AZ

Protection ClassIP 67 (connection box with Pg 13.5 cable connector)IP 68 (connection box with Pg 13.5 cable connector) and PU resin compoundIP 67 (connection box with NPTAdapter)

234

Design1)


124


DN 3 [1/10“] to DN 8 [5/16“] DN 10 [3/8“] to DN 1000 [4“]




20


Dimensions: Stainless Steel Flowmeter Primaries, DN 3 to DN 100 [1/10“ to 4“], Wafer Design

Model SE21W

A

83Cable Connector Pg 13.5

C

A*

B

G

EF

L

C D

Di

DN 3–DN 8 [1/10”–5/16”]

Di

13.6

41

#

1) Installation length with 2 grounding plates L + 3 mm# Mounting bracket optional

Meter Size DN Inch

PN

10–40CL 150/CL 300

JIS

L1) A* A B C C Di D E F G Weightappr. kg

Weightappr. lb (pound)

3 1/10 4 5/32 6 1/4 8 5/16 10 3/8 15 1/2

68 64 37 28 50 42

3 4 6 81015

45 108 62 197 1.5 3.31

20 3/4 78 74 42 28 50 50 20 54 112 66 205 2.0 4.4125 1 90 86 54 46 70 59 25 63 119 73 219 2.0 4.4132 11/4 98 94 62 46 70 69 32 73 124 78 229 2.5 5.5140 11/2 103 99 67 46 70 77 40 82 128 82 237 3.0 6.6150 2 117 112 – 60 110 95 47 100 136 50 213 4.0 8.8265 21/2 10–16

CL 150JIS

103 99 – 60 110 111 62 116 150 58 235 4.5 9.9280 3 103 99 – 60 110 128 74 133 157 66.5 250 6.5 14.33100 4 133 129 – 60 110 155 96 160 176 80 283 8.5 18.74

∅ ∅ ∅


Fig. 24 Flowmeter Primaries DN 3 to DN 100 [1/10” to 4”], Wafer Design

21


Dimensions: Flowmeter Primary, Variable Process Connections, DN 3 to DN 100 [1/10“ to 4“]

Model SE21_

3

2 1/2”–4”DN 65–100

A

B

83

103

G

EF

D

C#

2”DN 50


Number of Holes N

83Cable ConnectorPg 13.5

C#

B

A

G

EF

103

83

RohrL

3D

For installation lengths with process connections, see Pages 23–24.1) For additional weight due to process connections, see Pages 23–24.2) With mounting bracket G and F + 10.5 mm# Mounting bracket optional

Meter Size DN Inch

A D B C E F2) G2) N Weightappr. kg1)

Weightappr. lb1) (pound)

3–10 1/10−3/8 37 44 28 50 108 62 197 – 1.5 3.31

15 1/2 37 44 28 50 108 62 197 – 1.5 3.31

20 3/4 42 63 28 50 112 66 205 – 2.0 4.41

25 1 54 63 46 70 119 73 219 – 2.0 4.41

32 11/4 62 78 46 70 124 78 229 – 2.5 5.51

40 11/2 67 78 46 70 128 82 237 – 3.0 6.61

50 2 128 100 60 110 136 50 213 4 4.0 8.82

65 21/2 114 116 60 110 150 58 235 6 4.5 9.92

80 3 114 133 60 110 157 66.5 250 6 6.5 14.33

100 4 144 160 60 110 176 80 283 6 9.0 19.84

∅

DN 3−DN 40[1/10“−11/2“]

DN 50−DN 100[2“–4“]


Fig. 25 Flowmeter Primaries DN 3 to DN 100 [1/10” to 4”], Variable Process Connections

22


Dimensions: Stainless Steel Flowmeter Primaries, Adapters for Various Process Connections

Model SE21_

L

Di

Da

L

Rd

Wgt

.

L

Di

1) Weight per pair

Meter Size DN Inch

Weld Stubs

ISO 2037 DIN 11850 DIN 2463

∅ Di ∅ Da LWeight1)



kg lb kg lb kg lb

310 1/103/8 10.0 13.0 127 0.4 0.88 10.3 13.5 127 0.4 0.88

15 1/2 16.0 19.0 127 0.4 0.88 18.1 21.3 127 0.4 0.88

20 3/4 20.0 23.0 132 0.7 1.54 23.7 26.9 132 0.7 1.54

25 1 22.6 25.0 149 0.7 1.54 26.0 29.0 149 0.7 1.54 25 28 149 0.7 1.54

32 11/4 31.3 33.7 166 1.0 2.20 32.0 34.0 166 1.0 2.20 32 35 166 1.0 2.20

40 11/2 35.6 38.0 171 1.0 2.20 38.0 41.0 171 1.0 2.20 36.8 40 171 1.0 2.20

50 2 48.6 51.0 173 1.0 2.20 50.0 54.0 173 1.0 2.20 49 52 173 1.0 2.20

65 21/2 60.3 63.5 165 1.4 3.09 66.0 70.0 165 1.4 3.09 66 70 165 1.4 3.09

80 3 72.9 76.1 169 2.0 4.41 81.0 85.0 169 2.0 4.41 81 85 169 2.0 4.41

100 4 97.6 101.6 199 2.6 5.73 100.0 104.0 199 2.6 5.73 100 104 227 3.0 6.61

Meter Size DN Inch

Food Industry Fittings Tri-Clamp

DIN 11851 DIN11864-1 (Form B) DIN 32676

Rd. Thds. LWeight1)

Rd. Thds. LWeight1)

∅ Di LWeight1)

kg lb kg lb kg lb

310 1/103/8 28 x 1/8” 169 0.5 1.10 34 x 1/8” 161 0.5 1.10 10.0 163 0.5 1.10

15 1/2 34 x 1/8” 169 0.5 1.10 44 x 1/6” 161 0.5 1.10 16.0 163 0.5 1.10

20 3/4 44 x 1/6” 180 0.9 1.98 44 x 1/6” 170 0.9 1.98 20.0 168 0.7 1.54

25 1 52 x 1/6” 207 0.9 1.98 52 x 1/6” 197 0.9 1.98 26.0 192 0.8 1.76

32 11/4 58 x 1/6” 230 1.4 3.09 58 x 1/6” 220 1.4 3.09 32.0 209 1.5 3.31

40 11/2 65 x 1/6” 237 1.4 3.09 65 x 1/6” 227 1.4 3.09 38.0 214 1.4 3.09

50 2 78 x 1/6” 243 1.4 3.09 78 x 1/6” 233 1.4 3.09 50.0 216 1.2 2.65

65 21/2 95 x 1/6” 245 2.2 4.85 95 x 1/6” 233 2.2 4.85 66.0 221 1.6 3.53

80 3 110 x 1/4” 259 3.2 7.05 110 x 1/4” 245 3.2 7.05 81.0 225 2.4 5.29

100 4 130 x 1/4” 307 4.4 9.70 130 x 1/4” 291 4.4 9.70 100.0 255 3.1 6.83

Weld Stubs perDIN 11850 or ISO 2037 or DIN 2463

Food Industry Fittingper DIN 11851

TriClamp perDIN 32676


Fig. 26 Dimensions DN 3 to DN 100 [1/10” to 4”], Adapters for Variable Process Connections

23


Model DS21

Weld Stubs

FoodIndustryFitting

a

L

R

L

DIN 11850, ISO 2037

∅D

i

DIN 11851

L

ExternalThreads

Meter Size Weld Stubs Food Industry Fittings

DIN 11850L

Weight1)DIN 11851

L

Weight1)

DN Inch

kg lb kg lb

3−10 1/10−3/8 127 0.4 0.88 169 0.5 1.1015 1/2 127 0.4 0.88 169 0.5 1.1020 3/4 132 0.7 1.54 180 0.9 1.9825 1 149 0.7 1.54 207 0.9 1.9832 11/4 166 1.0 2.20 230 1.4 3.0840 11/2 171 1.0 2.20 237 1.4 3.0850 2 173 1.0 2.20 243 1.4 3.0865 21/2 165 1.4 3.08 245 2.2 4.8580 3 169 2.0 4.41 259 3.2 7.05100 4 199 2.6 5.73 307 4.4 9.70

1) Weight per pair

Meter Size External Threads ISO 228 / DIN 2999

R a LWeight 1)

DN Inch kg lb3−10 1/10−3/8 3/8” 18 139 0.4 0.8815 1/2 1/2” 18 139 0.4 0.8820 3/4 3/4” 25 164 0.8 1.7625 1 1” 25 179 0.8 1.76


Fig. 27 Dimensions, Model SE21, DN 3 to DN 100 [1/10” to 4”], Adapters for Variable Process Connections

24


Dimensions: Stainless Steel Flowmeter Primaries, 1/8“-Sanitary Connectors, DN 1 to DN 2 [1/25“ to 1/12“]

Model SE21B

118

9248

10

26

40

25

69

2

60

90

64

(135)

41


4 x ∅ 5.5

1

2

Note:

Connection dimension for G 1/8” coupling, internal threads

Mounting bracket optional

Information:Grounding electrodes are integrated in the flowmeter primary as standard and are made of the same material as the signal electrodes.

1) For hose 6 x 4 mm

Process Connections DN Inch PNWeight

kg lb

1/8” Sanitary connection1) 1 2 1/25 1/12 10 1.5 3.31

2

1


Fig. 28 Flowmeter Primaries DN 1 to DN 2 [1/25” to 1/12”]

25


Ordering Information: Stainless Steel Flowmeter PrimariesIn addition to the Ordering Number please supply the following information: Fluid, fluid temperature, operating pressure, flow range, pipeline type (grounding plate, grounding electrode)1)

Continued on next page 1) Only required for Wafer Design and pipelines with insulating liners. 2) DN 1−2 [1/25”−1/12”] always order with same material as signal electrodes, standard.

Ordering Number SE21Process ConnectionsWafer Design DN 3–100 [1/10–4“] Weld stubs DIN 11850 DN 3–100 [1/10–4“] Weld stubs DIN 2463 DN 3–100 [1/10–4“] Weld stubs ISO 2037 DN 25–100 [1–4“] Food Industry fitting DIN 11851 DN 3–100 [1/10–4“] TriClamp DIN 32676 DN 3–100 [1/10–4“] External threads ISO 228/DIN 2999 DN 3– 25 [1/0”1”] No adapter 1/8”Sanitary connectors DN 12 [1/25”3/32”] Others

WRQPSTEVBZ

Liner MaterialPFA (DN 3 100 [1/10”4”]) Peek (DN 12 [1/25”1/12”]) Torlon (DN 12 [1/25”1/12”])

PKN

Meter Size InchDN 1 1/25 DN 1.5 1/17 DN 2 1/12 DN 3 1/10 DN 4 5/32 DN 6 1/4 DN 8 5/16

011S0203040608

DN 10 3/8 DN 15 1/2 DN 20 3/4 DN 25 1

10152025

DN 32 11/4 DN 40 11/2 DN 50 2 DN 65 21/2 DN 80 3 DN 100 4

32405065801H

Measuring Electrode /Grounding Electrode Material2)

SST No. 1.4571[316Ti] /none Hastelloy B2 /none Hastelloy C4 /none standard Titanium /none Tantalum /none SST No. 1.4539 /none (Food Industry applications) PlatinumIridium /none

SBHMTFP

SST No. 1.4571[316Ti] /with Hastelloy B2 /with Hastelloy C4 /with Standard Titanium /with Tantalum /with SST No. 1.4539 /with (Food Industry applications) PlatinumIridium /withOthers

ENOIQRGZ

Pressure RatingPN 10 TriClamp (DN 65–100); external threads, Food Ind. fitting, weld stubs (DN 65, 100) PN 16 Wafer Design, TriClamp DN (3–50); Food Ind. fitting, weld stubs DN 50, 80) PN 40 Wafer Design (DN 3–50); Food Ind. fitting, weld stubs (DN 3–40) JIS K10 Wafer Design DN 3–100 [1/10”4”] ANSI CL 150 Wafer Design DN 3–100 [1/10”4”] ANSI CL 300 Wafer Design DN 3–50 [1/10”2”] Others

CDFKPQZ

26


1) Notes on design





Electrode Design

Standard Conical head (from DN 10 [3/8”] material SST No. 1.4539 used for high grease content fluids) Others

Gasket Materials

EPDM with FDAApproval (CIP capable, no oil or grease) Silicone with FDAApproval (suitable for oil and grease) PTFE (Teflon) None

Ordering Number SE21Process Connection MaterialsNone (only Wafer Design) SST No. 1.4571 [316Ti] (only DN 1–2 [1/25”−1/12”]) SST No. 1.4404 [316L] standard POM (DN 1−2 [1/25”−1/12”]) Others

03489

Instrument Mounting BracketNoneWithOthers

ACZ

Temperature RangeStandard design ≤ 130 °C (DN 1–2 [1/25”1/12”] max. 120 °C) SCertificationsNoneMaterial certified per EN 10204 Par. 3.1B and pressure test per AD2000Inspection Certificate EN 10204 3.1BPressure test per AD2000

ADFG


AZ

Protection ClassIP 67 (connection box with Pg 13.5 cable connector)IP 68 (connection box with Pg 13.5 cable connector) and PU resin compoundIP 67 (connection box with NPTAdapter)

234

Design1)


124


DN 3 [1/10“] to DN 8 [5/16“] DN 10 [3/8“] to DN 1000 [4“]




27


Installation Accessories

Fig. 29 Protection Plates/Grounding Plates

The loose grounding plates are installed between the flowmeter flange and the mating flange.

Available for sizes DN 3–DN 600 [1/10“–24“]. Mat. SS 1.4571[316Ti] other materials upon request .

Protection Flanges

Protection flanges protect the liner from abrasive fluids and are centered in the pipeline using a groove or spring. Protection flanges are available in 2 thicknesses and are mounted on the intrument. Added installation length for Series 1000 and DIN/ANSI flanges ≤ DN 80 [3“] L + 20 mm, from DN 100 [4“] L + 25 mm.

Gaskets for Protection Plates/Grounding Plates

Only one gasket at the mating flange is required for PTFE/PFA lined instruments installed with metal grounding plates. A gasket should be placed on either side of the grounding plate for hard/soft rubber lined instruments. Commercially available gaskets made of a material (rubber, lt, PTFE, etc) compatible with the fluid and the operating temperatures should be used.

Chemical Applicationd (Grounding)

For plastic pipelines or pipelines with insulating liners, protection/grounding plates made of conductive PTFE (patent applied for), replace the expensive special materials (Platinum, Tantalum etc.) presently used. Succesfully tested in numerous applications.

Wafer Design Accessories for Model SE21W

The following accessories are available as a function of the meter size and the pressure rating: Bolts, nuts, lockwasher, centering elements Gaskets are not included ion the accessories.

Material: SS

DN (inch) PN T=Thick3–80 1/10–3 10–40 1,5

100–150 4–6 25–40 1,5100–250 4–10 10–16 1,5300–600 12–24 10–16 3

∅A

∅B

C

6.4

20

10

T

Groundconnection 1)

Grounding Plate, Loose (Centeredby Mounting Bolts)

R8

16

6,6

R2 R2

R8

16

∅B

Groundconnection 1)

Protection Plate/Grounding PlateMounted on Flowmeter 2)

1) Attach ground cable with a M6 screw, lock washer and nut to the plate. ∅B = Inside diameter of the lining

2) Grounding plate mounted directly on the instrument DN 10 to DN 600 [3/8“ to 24“] Material: Stn. stl. 1.4571 [316Ti] Thickness ≤ DN 100 [4“] = 3 mm, ≥ DN 125 [5“] = 5 mm ∅B = Inside diameter of the lining

Fig. 30 Grounding plate

Nennweite (inch) PN ThicknessDN 10–100 3/8“–4“ 10–40 4 mm< DN 200 upon request

Meter Size Pressure Rating Part NumberDN 3 to 101/10“ to 3/8“

PN 10 40 D614L265U03150 lb D614L265U03300 lb D614L265U04

DN 151/2“


DN 203/4“


DN 251“


DN 321 1/4“


DN 401 1/2“


DN 502“


DN 652 1/2“

PN 10 16 D614L297U08150 lb D614L297U10

DN 803“

PN 10 40 D614L298U08150 lb D614L298U09

DN 1004“

PN 10 16 D614L299U07150 lb D614L299U09

R8 R2

d2

di

Dk

6.6

16

4±0.5l1

N Holes at scale

Fig. 31 PTFE Protection/Ground Plates

28


Specifications: Converter

Fig. 32 Converter FSM4000S4

Flow Range

Any flow range whose 100 % value corresponds to a flow velocity between 0.5 m/s and 10 m/s can be selected.

Minimum Conductivity

≥ 20 µS/cm standard DN 3–1000 [1/10”–40”] ≥ 5 µS/cm with preamplifier DN >8 [ 5/16”] ≥ 0.5 µS/cm with preamplifier DN 10–1000 [3/8”–40”]

Reproducibility

≤ ± 0.2 % of rate

Response Time

1τ = 70 ms (0–66 %) in Operation mode „Fast“ 1τ = 200 ms (0–66 %) in Operation mode (Standard)

Supply Power

Unom = 115–230 V 50/60 Hz Urat = 85–253 V 50/60 Hz 50/60 Hz ± 6 % 20,4–26,4 V AC, 20,4–31,2 V DC Ripple ≤ 5 %

Power

S ≤ 45 VA (flowmeter primary including converter)

Ambient Temperature

20 to +60 °C [4 to +140 °F]

Storage Temperature

20 to +80 °C [4 to +176 °F]

Relatively humidity

Acc. to IEC 6006821

Vibration

Acc. to DIN EN 6006826 (10–55 Hz: amplitude = 0.15 mm)

Protection Class per EN 60529

IP 67 for field mount housing and NEMA 4X

Design

Field Mount Housing made of cast Alum. per DIN 1725, painted. Paint coat 60 µm thick. Lower section (RAL 7012), upper section (RAL 9002). Dimensions Page 35. Weight appr. 3.3 kg (7.28 pound).

Electrical Connections

Cable entry M20 x 1.5, NPT, PF with adapter (upon request), screw terminals

Damping

Selectable from 0.1 to 99.0 s

Zero Return

Selectable from 0 to 10 % of range end value

Signal Cable

Max. cable length between flowmeter primary and converter is: 50 m for the standard design and versions with automatic zero return, from DN 10 [3/8”] and from 20 µS/cm. 200 m for designs with preamplifiers. A 10 m long signal cable is included with flowmeter. If a longer cable is required, see Footnote on Page 35, Ordering Information, Converter.

Magnet Coil Supply Cable

Is required for connecting the flowmeter primary to the converter. For EMCreasons the 2 wire cable is shielded. A 10 m long cable is included with flowmeter. If a longer cable is required, see Footnote on Page 35, Ordering Information, Converter.

Forward/Reverse Flow Metering

The flow direction is indicated in the display by direction arrows. It is also possible to transmit the flow direction information over the contact output.

Display

4line, lighted, graphic display. To improve the readability, the flow information can be displayed on two lines with larger characters. The individual flowrate and output values can be displayed. Nonswitching dotmatrix display with max. 4 x 16 characters. An clear text error diagnosis is displayed when the system monitor detects an error condition. The alarm condition can also be signaled over the alarm output.

Data Security

All data is stored in a FRAM (Ferroelectric Nonvolatile Random Access Memory) for a 10 year period without requiring power during a power outage or when the main supply power is turned off. Additional security is provided by a serial FRAM installed in the converter and on the external connection board in which the parameter settings and process information are stored. The data in the external FRAM can be uploaded into the converter. Thereby an easy converter exchange is possible without reconfiguration by simply uploading the stored data from the external FRAM into the new converter.

29


Flow Totalization

The flow is totalized in engineering units. The pulse factor, pulses per unit, can be set between 0.001 and 1000. The totalizer values for the forward and reverse flow directions can be displayed simultaneously. Display selections are made in the submenu "Display".

Parameter Settings

Entries are made using menus displayed in a number of languages (German, English, French, Finnish, Swedish, Italian, Spanish and Dutch) using 3 keys in dialog with the display or by communication over a data link, using a PC, HARTProtocol or Profibus (in preparation).A Magnet Stick can be used for configuration without opening the front door. Position the Magnet Stick over the magnet symbols on the cover over the display.

Alarm Signals

The converter can incorporate a max/minalarm. The alarm limits can be set anywhere within the range of 0–105 % of the flow range end value. When the flowrate is outside of the alarm limits set, an error message is displayed in the upper line. It is also possible to transmit a signal over the contact output.

Upgrade

The converter with all its functions can also be used with older model electromagnetic flowmeters. The appropriate model number must be selected in the converter. It is also possible to use the converter with flowmeters Model 10D1422. A special converter version is required when updating an older model (see Ordering Information, Converter) and is applicable to the meter size range DN 3 to DN 1000 [1/10" to 40"] only in the low voltage design.

Isolation In-/Output

The current output, pulse output and the contact input and contact output are galvanically isolated from the input circuit and from each other.

In-/Output Signals

Current Output (terminals 31, 32)

The following functions are available in the software:0 to 20 mA load ≤ 560 Ohm4 to 20 mA load ≤ 560 Ohm0 to 10 mA load ≤ 1120 Ohm2 to 10 mA load ≤ 1120 Ohm

Contact Output (terminals 41,42)

The following functions are available in the software:– Forward/reverse flow direction signal– Flowrate alarm (max. or min.)– General alarm– Empty pipeThe output contact can be configured as normally open or normally closed.

Optocoupler specifications16 V ≤ UCEH ≤ 30 V, 2 mA ≤ ICEL ≤ 220 mA

Scaled Pulse Output (terminals 51, 52)

Maximum count frequency 5 kHz. Pulse factor per engineering unit from 0.001 to 1000/unit selectable in the software. The pulse width can be set from 0.100 ms to 2000 ms.The design (active, passive) can be selected using jumpers.

Active

Voltage pulse 24 V rectangular, – Load ≥ 150 Ohm,

Pulse width ≤ 50 ms, count frequency ≤ 3 Hz,– Load ≥ 500 Ohm,

Pulse width ≥ 0.1 ms, max. count frequency: 5 kHz.

Passive

Optocoupler"closed ": 0V ≤ UCEL ≤ 2 V, 2 mA ≤ ICEL ≤ 220 mA"open": 16 V ≤ UCEH ≤ 30 V, 0 mA ≤ ICEH ≤ 2 mA

Contact Input (terminals 81/82)Passive contact (normally open). The following functions are available in the software:

External Zero Return

When the pipeline empties all output signals can be turned off. The current output can be set to 0 mA or 2/4 mA dependent on the current output range selection.

External Totalizer Reset

Resets the internal totalizer value in the display and the pulse counter for both flow directions.

Design Passive (optocoupler)

„ON“: 16 V ≤ UKL ≤ 30 V „OFF“: 0 V ≤ UKL ≤ 2 V Ri: 2 kΩ

30


HART

FlowmeterPrimary

Hand TerminalPC

Converter

4-20 mA

Bell 202Modem Box

R min = 250 Ohmb

Fig. 33 HARTProtocol

HART®-Protocol Version 5.xThe HART®Protocol provides for communication between a process control system, Hand Terminal and the EMF field instrument. The communication signals, which are superimposed as an AC voltage on the current output, do not affect any other instruments connected to the current output. This option is only available with a 420 mA current output.

Transmission Type

FSKModulation on the current output 420 mA per Bell 202 Standard.

Baudrate

1200 Baud

Format

Logic 1: 1200 Hz Logic 0: 2200 Hz

Cable

Max. 1500 m AWG 24 twisted and shielded

Max. Signal Amplitude

1.2 mApp

Load Current Output

min.: 250 Ω, max.: 560 ΩThe digital communication on the current output does not affect any other connected instruments.To configure using SmartVision a DTM (Device Type Manager) is required.

System Connections

In conjunction with the DTM (Device Type Manager) available of the instrument (Software Revision from B.10) the communication (Configuration, Parameter Settings) can be activated using the appropriate applications per FDT 0.98 or 1.2 (SMART VISION 4.01 R2).

AMS

in preparation

PROFIBUS PA

in preparation

FOUNDATION Fieldbus FF

in preparation

31


Connection Examples for Peripherals

* RB ≥ UCEICE

+31

32

0/4–20 mA

0/2–10 mA

externalinternal

Current Output active with/without HART-Protocol (4–20) mA

externalinternal

Scaled Pulse Output passive, optocoupler

52

51+16–30 V DC

RB*

52

+24 V DC

–

externalinternal

Scaled Pulse Output active

51

41

42

externalinternal

RB*+U 0 V

+24 V DC

externalinternal

82

81+16–30 V DC

0 V

RI

Contact output for system monitor, max.min.alarm, empty pipe or forward/reverse flow direction signal. Function software selectable

Contact input for external totalizer reset and external zero return Function software selectable

Fig. 34 Connection Examples for Peripherals

32


Interconnection Diagram: Flowmeter Primary DN 1 to DN 1000 [1/25“–40“], Converter Field Mount Housing

2

LM3 M1323151 52 41 N

1+

1)2)3)4)

8212S 2 161S3

8) UU+

42

6)7)

UU+

2S3 1S 163

1633

SE

SE

M3 M1 SE

M3 M1 SE

3 81

24 V +

5)

12

12

Functional Earth

Functional Earth

Converter S4Field Mount Housing

Flowmeter Primary

With preamplifier(always at DN1[1/25”] DN8 [5/16”])

Comment:We recommend that the output cables be shielded with the shield at one end connected to functional earth.

1) Supply power High voltage:

Low voltage:

Frequency:

Urat = 85 V AC to 253 V AC / Unom = 115 to 230 V AC Terminals L, N, 20.4 to 26. V AC, 20.4 to 31.2 V DC Terminals 1+, 2, 47 Hz ≤ f ≤ 53 Hz; 50 Hz Supply power 56 Hz ≤ f ≤ 64 Hz, 60 Hz Supply power

2) Magnet coil supply: Shielded 2 x 1 mm² CE Type 227 TEC 74 ABB Part No. D173D147U01 10 m included with shipment standard

3) Current output:Function:

Software selectableActive 0/4–20 mA, 0/2−10 mA,0 Ω ≤ RB ≤ 560 Ω Terminals: 31, 32

4) Contact output:Function:

Software selectable Passive„closed“: 0V ≤ UCEL ≤ 2 V, 2 mA ≤ ICEL ≤ 220 mA „open“: 16 V ≤ UCEH ≤ 30 V, 0 mA ≤ ICEH ≤ 2 mA Terminals: 41, 42

5) Contact input:Function:

Software selectable Passive„On“: 16 V ≤ UKL ≤ 30 V „Off“: 0 V ≤ UKL ≤ 2 V Ri = 2 kΩ Terminals: 81, 82

6) Pulse output:Function:

SelectableActive/Passive fmax: 5 kHz, pulse width 0.1 ms–2000 ms Setting range:0.001–1000 pulses/units „closed“: 16 V ≤ UCEH ≤ 30 V, 2 mA ≤ ICEH ≤ 220 mA „open“: 0 V ≤ UCEL ≤ 2 V, 0 mA ≤ ICEL ≤ 2 mA Terminals: 51, 52

7) Shielded signal cable: ABB Part No. D173D018U02, 10 m included with shipment.

8) Shielded signal cable: Voltage supply for flowmeter primary with preamplifier Terminals +U, U instead of on 2S and 1S in the standard instrument.

Attention!Is the flowmeter primary includes a preamplifier either for low conductivity applications or for flowmeter sizes DN 1 to DN 8 [1/25“ to 5/16“], the supply voltage ± 12 V DC must be connected to terminals U+ and U at both the flowmeter primary and at the converter.

Fig. 35 Interconnection Converter S4

33


Interconnection Diagram: Upgrade Flowmeter Primary DN 3 to DN 1000 [1/10“–40“], Converter Field Mount Housing, Model 10D1422 (10DI1425, 10DS3111A-C DN 500–1000 [20“–40“])

LM3 M1323151 52 41 N

1)

2)

3)4)

8212S 2 161S3

8)

42

6)7)

3 67SE L N

673 81

24

V +

5)

12

Functional Earth

Functional Earth

Converter S4Field Mount Housing

Flowmeter Primary

Comment:We recommend that the output cables be shielded with the shield at one end connected to functional earth.

1) Supply Power High voltage:

Frequency:

Urat = 85 V AC to 253 V AC / Unom = 115 to 230 V AC Terminals L, N, 47 Hz ≤ f ≤ 53 Hz; 50 Hz Supply power 56 Hz ≤ f ≤ 64 Hz, 60 Hz Supply power

2) Magnet coil supply: Magnet coil supply from Supply power3) Current output:

Function:Software selectableActive 0/4–20 mA, 0/2−10 mA, 0 Ω ≤ RB ≤ 560 Ω Terminals: 31, 32

4) Contact output:Function:

Software selectable Passive„closed“: 0V ≤ UCEL ≤ 2 V, 2 mA ≤ ICEL ≤ 220 mA „open“: 16 V ≤ UCEH ≤ 30 V, 0 mA ≤ ICEH ≤ 2 mA Terminals: 41, 42

5) Contact input:Function:

Software selectable Passive„On“: 16 V ≤ UKL ≤ 30 V „Off“: 0 V ≤ UKL ≤ 2 V Ri = 2 kΩ Terminals: 81, 82

6) Pulse output:Function:

SelectableActive/Passive fmax: 5 kHz, pulse width 0.1 ms–2000 ms Setting range: 0.001–1000 pulses/units „closed“: 16 V ≤ UCEH ≤ 30 V, 2 mA ≤ ICEH ≤ 220 mA „open“: 0 V ≤ UCEL ≤ 2 V, 0 mA ≤ ICEL ≤ 2 mA Terminals: 51, 52

7) Shielded signal cable: ABB Part No. D173D018U02 using this signal cable or use the available installation8) Reference cable: Only for connecting to reference cable terminals: Terminals: 6, 7 in Model 10D1422

Attention!Supply power see name plate primary

Terminal board: D685A1020U03 Switch S903 must be closed

Fig. 36 Interconnection Upgrade Converter S4

34


Ordering Information: Converter S4In addition to the Ordering Number please supply the following information: Flow range, if applicable current output, pulse output active/passive, pulse factor and pulse width. These selections can be factory preset.

Ordering Number S4

External Converter S4 ± 0.5 % v. M.

HousingField mount housing (with cable connector M20x1.5), standardField mount housing (with adapter for cable connector NPT 1/2“)

AB

Supply PowerHigh voltage 85–253 V ACLow voltage 20.4–26.4 V AC, 20.4–31.2 V DC

GK

DisplayMagnet Stick operation and graphic display, lighted A

In-/Output OptionsCurrent output + Pulse output active + Contact input + Contact outputCurrent output + Pulse output active + Contact input + Contact output + HARTCurrent output + Pulse output passive + Contact input + Contact outputCurrent output + Pulse output passive + Contact input + Contact output + HARTContact output + PROFIBUS PAContact output + FOUNDATION Fieldbus FFContact output + PROFIBUS PA with M12 plug

1)

1)

01020304070810

in preparationin preparationin preparation

ApplicationStandard 0

For Flowmeter PrimaryFlowmeter Primary Type SE2_, SE4_, standardFlowmeter Primary Type DS2_, DS4_, 10DS3111, 10DI1425Flowmeter Primary Type 10D1422, 10DI1425 (≥ DN 500)2)

Others

1239

ApprovalsNone 0

Name PlateGermanEnglishFrenchStainless Steel GermanStainless Steel EnglishStainless Steel French

GEFGNENFN

Design Level *

Software Level *

1) Option not available for Supply power „Low voltage“Shielded signal cable, 10 m included with each flowmeter. For longer cables order Part No. D173D018U02.Shielded coil supply cable, 10 m included with each flowmeter. For longer cables order Part No. D173D147U01.

2) The connection board for the reference cable includes a voltage splitter, magnet coil supply for the flowmeter primary from a separate external power supply. FRAMVariant Cs = 100 % and Cz = 0 % required.

35


265

198

10

14.5

132

66

139.7

38

83.5

167

249

7

Min

.175

min. 62

Field Mount Housing with Window Cable Connector M20 x 1.5 Mounting Dimensions

1) 1)

1)1)

1) Mounting holes for 2” pipe mounting kit

Mounting kit upon request


Opening the Housing Cover

– Loosen the cover screws.– Remove cover or flip open the cover with a

window.

Closing the Housing Cover

– Press the cover with window on its closure side against the gasket surface and install and tighten the cover screws.

– Set the small cover in the frame and install and tighten the cover screws.

Fig. 37 Dimensions, Converter Housing and Installation proposal

Dimensions: Field Mount Housing

36


Ordering Number: Test simulator

1) Supply power must correspond to value listed on the converter Name Plate.2) The adapter listed above for Converters 50XM2000/50XE4000/E4 can also be used for existing simulators 55XC2000.

If two adapters are required, then the Ordering Number for each adapter type is to be used.

SoftwareMeter parameter documentation software for PC upon request. SMART VISION Communication tool for HART ® No charge for 90 day evaluation version.DTM‘s are included in SMART VISION Tool.

Flowmeter Primary Simulator 55XC4

Setting the Flow SignalNone (adapter only)3position Digiswitch with 1000 steps

01

Supply power 1)

None (Adapter orders only)110 V–240 V (50/60 Hz) with Schuko plug24 V/48 V (AC/DC) with 4 mm plug110 V–240 V (50/60 Hz) with USA plugOthers

01239

AccessoriesNoneAdapter for converter 50XM2000/50XE4000/E4/50XF4000Adapter for simulator 55XC2000 2)

Adapter plate for converter S4Others

01259

Design Level(Specified by ABB) *

Name PlateGermanEnglishFrench

123

37


38


39

U02

Rev

. 03

The IndustrialIT wordmark and all mentioned product names in the form XXXXXXIT are registered or pending trademarks of ABB.

ABB has Sales & Customer Supportexpertise in over 100 countries worldwide.

www.abb.com

The Company’s policy is one of continuous productimprovement and the right is reserved to modify the

information contained herein without notice.

Printed in the Fed. Rep. of Germany (10.03)

© ABB 2003

D18

4S07

3

ABB Ltd.Oldends Lane, StonehouseGloucestershire, GL 10 3TAUKPhone: +44(0)1453 826661Fax: +44(0)1453 827856

ABB Inc.125 E. County Line RoadWarminster, PA 18974USAPhone: +1 215 674 6000Fax: +1 215 674 7183

ABB Automation Products GmbHDransfelder Str. 237079 GöttingenGERMANYPhone: +49 551 905534Fax: +49 551 905555

EMail Customer Care Center:[email protected]

d184s073u02 electromagnetic flowmeter...

Documents