data domain lab guide

Backup and Recovery Solutions DivisionEMC Data Domain2421 Mission College BoulevardSanta Clara, CA 95054866-WE-DEDUPE408-980-4800www.datadomain.com

EMC Data Domain System Administration Course Lab Guide

February 2012

MR-1CN-DDSADMIN

EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without notice. THE INFORMATION IN THIS PUBLICATION IS PROVIDED AS IS. EMC CORPORATION MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WITH RESPECT TO THE INFORMATION IN THIS PUBLICATION, AND SPECIFICALLY DISCLAIMS IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Using, copying, and distributing EMC software described in this publication requires an applicable software license. EMC2, EMC, Data Domain, Global Compression, SISL, the EMC logo, and where information lives are registered trademarks or trademarks of EMC Corporation in the United States and other countries. All other trademarks used herein are the property of their respective owners. Copyright 2009-2011EMC Corporation. All rights reserved. Published in the USA.

ContentsContents 3

Lab 2.1: Access the VDC 7Introduction 7

Note for Non Windows XP Users 7

Login Information 8

Log into VDC 8

Log into Vmware vCenter 9

Clone VM template copy 10

Build and deploy your VM copy 12

Log Into the Virtual Windows desktop 13

Lab 2.2: Initial Configuration 17Introduction 17

Launch the Configuration Wizard 17

Lab 2.3: Copy Files and Create a CIFS Share 21Introduction 21

Monitor system activity 21

Map a network drive 22

Copy and paste files 25

Confirm space usage 25





Create a CIFS share in a Data Domain system 28

Lab 5.1: Configure Snapshot 31Introduction 31

Configure a snapshot 31

Access a snapshot 33

Test a snapshot 34

Lab 5.2: Configure Fast Copy 35Introduction 35

Configure Fast Copy 35

Access Fast Copy 36

Lab 5.3: Configure Sanitization 37Introduction 37

Review installed licenses 37

Configure sanitization 38

Monitor sanitization 394 EMC Data Domain System Administration Course Lab Guide

Lab 5.4: Configure Encryption 41Introduction 41

Review installed licenses 41

Configure encryption 41

Lab 5.5: Configure File System Cleaning 45Introduction 45

Configure file system cleaning 45

Start the cleaning operation 46

Destroy a file system 48

Create a file system 49

Lab 6.1: Configure Replication 51Introduction 51

Review installed licenses on the source Data Domain system 51

Prepare the source Data Domain system for replication 51

Add the replication target Data Domain system 54

Review installed licenses on the target Data Domain system 56

Configure replication 56

Verify replication 58

Lab 7.1: Configure DD Boost with EMC NetWorker 61Introduction 61

Review installed licenses on the source Data Domain system 61

Prepare the source Data Domain system for DD Boost 61

Review the installed licenses on the target Data Domain system 63

Prepare the target Data Domain system for DD Boost 64

Add source Data Domain system information in NetWorker 65

Add target Data Domain system information in NetWorker 68

Configure NetWorker to perform a backup to the source Data Domain system 70

Configure NetWorker to perform a backup clone to the target Data Domain system 73

Perform backup to source Data Domain system 75

Perform a backup clone to the target Data Domain system 76

Verify Space Usage and File System Stats on Data Domain Systems 77

Lab 7.2: Configure DD Boost with Symantec NetBackup 79Introduction 79

Create a NetBackup Windows 2008 image 79

Review Installed Licenses on the Source Data Domain System 79

Prepare the Source Data Domain System for DD Boost 80

Review the Installed Licenses on the Target Data Domain System 81

Prepare the Target Data Domain System for DD Boost 82Contents 5

Verify and install a Data Domain plug-in on your Windows host 83

Configure the source Data Domain system as storage server in NetBackup 84

Configure and test the NetBackup backup policy 88

Configure the destination Data Domain system as storage server in NetBackup 91

Configure the NetBackup Storage Life Cycle Policy 95

Modify and test the NetBackup backup policy 98

Lab 9.1: Monitor a Data Domain System Using SNMP 103Introduction 103

Configure SNMP 103

Monitor a Data Domain system using SNMP 107

Lab 9.2: Monitor a Data Domain System Using Syslog 109Introduction 109

Configure a Kiwi Syslog application 109

Configure remote logging in a Data Domain system 111

Test remote logging 112

Lab 9.3: Manage Log Files 115Introduction 115

Manage Log Files 115

Lab 9.4: Autosupport and Support Bundle 117Introduction 117

Verify the mail server configuration 117

Configure autosupport 118

View an autosupport report 119

Test Autosupport 119

Reset an autosupport email list 120

Generate a Support Bundle 121

6 EMC Data Domain System Administration Course Lab Guide

Lab 2.1: Access the VDC

Introduction7

You perform Data Domain System Administration course labs in the EMC Virtual Data Center (VDC) using Windows and Linux Virtual Machines (VMs). VMs emulate client PCs and backup servers.

Note: Use the IE browser for these labs. The IE browser allows pop-ups.

Note: Pictures in this lab guide are for example only. They do not reflect your individual experience in the lab.

Note for Non Windows XP Users

The VDC gateway is designed to automatically perform a silent install of necessary Citrix plug-in for Windows XP.

If you are using other Operating Systems on your systems (Example: Windows 7), before proceeding to next section,

1. Please access below URL to download and install Citrix plug-in.

http://www.vclass.emc.com/vdcctxdls.html

2. After accessing the above URL, choose the link that best suits your requirement. This will open a new window with Citrix plugin download page

3. Download Citrix Online Plug-in - Web tool.

4. Install Citrix Online Plug-in - Web tool that you just downloaded.

Login Information

Use the information provided below to log into systems you will be using in the Data Domain System Administration labs. Obtain user names, passwords, domains, IP 8 EMC Data Domain System Administration Course Lab Guide

addresses and host names that are not provided below from you instructor. Record them here for use in subsequent labs.

Log into VDC

1. Log Into the Windows VM from your Internet Explorer (IE) browser.

https://vdc.emc.com

The VDC login screen appears:

2. Enter your assigned user name.

3. Enter your assigned password.

4. Click Login.

5. Allow the Citrix Web client installation to continue until the Security Warning dialog box appears:

User Name Password Domain External IP Address

IP Address Host Name

Local Lab PC

VDC & Lab Manager

Windows VM configuration

administrator abc123

Data Domain system

sysadmin abc123

Replication Target Data Domain system

sysadmin abc123

NetWorker Management Console

administrator password

Note: Dont do steps 5 and 6 if you are on Windows 2007.9

6. Click Install.

The Citrix License Agreement appears.

7. Click Yes to accept the Citrix License Agreement.

The EMC2 Education Services Virtual Data Center page appears:

Log into Vmware vCenter

1. Click on the Virtual Lab Manager link.

2. Wait for the Vmware vCenter Lab Manager 4.0 to load:




5. Click Login.

Clone VM template copy

1. Select the Library option under Build and Deploy in the left-hand navigation pane.

2. Under the Configuration Name column, hold your cursor over DDSA5.1.

A menu appears

The DDSA 5.1 configuration name includes an image of a Windows 2008 server and a Linux image. The Windows 2008 server is pre-configured with EMC NetWorker. You will use the Windows 2008 server for the labs.11

3. Select Clone to Workspace:

The Clone to Workspace dialog box appears.

4. Clone the configuration:

a. Select the New Configuration radio button.12 EMC Data Domain System Administration Course Lab Guide

b. Enter a name in the Name field, for example, JohnSmithVM.

c. Update the Storage Lease to 4 days.

d. In the Create a Linked Clone of section, select the Selected Virtual Machines: radio button.

e. Select the check box next to the VM icon.

f. Click OK.

The configuration is cloned and appears in your workspace.

Build and deploy your VM copy

1. Select Workspace under Build and Deploy in the left-hand navigation pane:

2. Deploy the VM to create an instance of the Windows VM:

a. Hold your cursor over the Configuration Name

b. select Deploy with Defaults from the pull-down menu.

c. Wait for the configuration to deploy.13

When the configuration is deployed, the Status of the VM changes to Deployed.

Log Into the Virtual Windows desktop

1. Click the VMware icon under the Consoles column:

The Windows Server 2008 log on screen appears:

Note: Even though you see the Press CTRL + ALT + DELETE to log on message and the CTRL+Alt+Del button on the Windows 2008 system screen, wait for the Windows 2008 system and all deployment processes to complete before you log on. This may take more than 5 minutes.

2. Once the system is fully deployed, Click the Ctrl+Alt+Del button located above the window:14 EMC Data Domain System Administration Course Lab Guide

3. Enter your administrator password. If you do not already have your administrator password, ask your instructor for it.

You may need to wait again to see your VM desktop. You may see a message like this:

Once your VM desktop is ready, it should look something like this:15

Lab 2.2: Initial Configuration

Introduction17

This lab covers initial configuration steps.

Caution: Make no changes in this lab. The lab systems are pre-configured, so this lab uses the wizard to review settings only.

Launch the Configuration Wizard

1. From your Windows VM, open a browser.

2. In your browser, enter the IP address or hostname of your assigned Data Domain system

Note: If you are using internet explorer version 8, you might get a security warning, click on Continue to this web site (not recommended). This is expected.



5. Click Login.

6. After you successfully login to the system, in the left navigation pane click on DD Network to expand the list of systems and select your Data Domain system. The status and summary page for that system will be shown in the right pane by default.

7. Go to Maintenance > System > Under More Tasks menu

8. Select Launch Configuration Wizard.

The configuration wizard appears. By default the licenses screen is shown.


9. In the licenses screen, review the licenses installed on your system. Click No.

Note: The lab systems licenses are pre-installed.

10. In the Global Deduplication Array (GDA) screen, click Next, as training Data Domain systems are not supported model for GDA.

11. In the network screen, Click Yes to configure your network.

12. In the General network screen, ensure the option is set to Obtain Settings using DHCP and click Next.

13. In the Interfaces screen, ensure Enabled and DHCP check boxes are selected for interfaces eth0a and eth0b. Click Next.

14. In the DNS screen, ensure Manually configure DNS list is selected and you see the DNS IP address in the box below. Click Next.

15. In the summary screen, ensure none of the field values are marked in bold and click Submit.

16. In the next screen ensure the network settings are configured successfully and click OK.

17. In the System Settings screen, click Yes.

18. In the Administrator screen, review options available. Do not make any changes to password and click Next.

19. In the Email screen, review options available and click Next.

20. In the Summary screen, review the configuration and click Submit.

21. In the next screen ensure the system configurations are configured successfully and click OK.

22. In the CIFS Protocol screen, click Yes.19

23. In the Authentication screen, ensure mode is set to Workgroup and Workgroup Name is set to Use Default. Click Next.

24. In the Share screen, do not create any shares and click Next.Note: Shares screen can be used to create new shares, but we are not going to create any shares in this lab.


26. In the next screen ensure the CIFS protocol is successfully configured and click OK.

27. In the NFS Protocol screen, click Yes.

28. In the Export screen, in the Directory Path field, type

/data/col1/backup

29. In the Export screen, under Clients section, click on the green + sign. This opens a new Client window.

a. In the Client field, type * and ensure the options are configured as per table and click OK. This will bring you back to the Export screen.

b. In the Export screen, under Client section, ensure the check box next to Client is selected and click Next.


31. In the next screen ensure the NFS protocol is successfully configured and click OK.

32. In the DD Boost Protocol screen, click No.

Note: You can use DD Boost Protocol screen to configure DD Boost on a Data Domain system. You configure DD Boost in another lab.

33. In the VTL Protocol screen, click OK.

Note: The training lab systems do not have VTL cards. VTL cannot be configured on these Data Domain systems.

Read-Only permissions (ro) Not selected

Allow connections from ports below 1024 (secure) Selected

Map root users to anonymous UID/GID (root_squash) Not selected

Map all users to anonymous UID/GID (all_squash) Not selected

Use Default Anonymous UID/GID Selected

Lab 2.3: Copy Files and Create a CIFS Share

Introduction21

In this lab you test a successfully configured Data Domain system by accessing it via CIFS and copying files to it.

Note: Screen shots in this lab are for instructional purposes only. They may not reflect your lab experience.

Monitor system activity

When you copy files to a Data Domain system you can monitor the system performance from the Enterprise Manager and the CLI. Later in this lab, you will copy files to your Data Domain system. To monitor system performance during the copy process:

1. Open the Enterprise Manager.

2. Select your system from the left navigation pane.

3. Go to Status > Stats.

4. Leave this window open so that you can monitor the disk write activity when you copy files later in this lab:

You can also use the below command in the CLI.

system show status 2

Map a network drive

In this section you map a network drive to the /backup share on your Data Domain system.22 EMC Data Domain System Administration Course Lab Guide

1. On your desktop, double click the Computer icon to open the computer window.

2. In the Computer window, select Tools and choose Map Network Drive. This opens Map Network Drive window.

3. In the Map Network Drive window, select Drive B:

4. In folder field type network path for your Data Domain system backup directory.Example: \\ddsystem\backup23

5. Select check box for Reconnect at logon.

6. Click on Connect using different user name. This opens the Connect As... window.

7. In the Connect As... window enter the User name sysadmin and your Data Domain system account Password:

8. Click OK. This closes the Connect As... window and takes you back to the Map Network Drive window.24 EMC Data Domain System Administration Course Lab Guide

9. Click Finish in the Map Network Drive window.

A new window for the B: drive appears:

Copy and paste files

1. In the Windows VM desktop, double click the Training folder. This opens a new window for the Training folder.25

2. Open the Sample Tar Files folder.

3. Copy the test250m.tar file and paste it into the B: drive (this is your Data Domain system/backup folder).A file transfer window opens and shows the copy progress.

You can also monitor the system performance during the copy from the Enterprise Manager (see Monitor system activity in this lab) or by using the below command from the command line.

system show stats 24. When the copy is complete, the test250m.tar file is copied to the /backup share on

your Data Domain system (using the CIFS protocol).

Confirm space usage

1. Go to the Enterprise Manager window.

2. Confirm that your Data Domain system is selected in left navigation pane.

3. Go to Data Management > File System > Summary.

4. Under the Summary tab, review your Data Domain system space usage.

5. Review the summary on the Currently Used line. 26 EMC Data Domain System Administration Course Lab Guide

6. Record the Currently Used information for your system (not from the above example):

Compression Definitions


1. Copy the test500m.tar file from the Training folder and paste it into the B: drive (your Data Domain system /backup folder).

You can also monitor the system performance during the copy from the Enterprise Manager (see Monitor system activity in this lab) or by using the below command from the command line.system show stats 2

Confirm space usage

1. Go to the Enterprise Manager.

Pre-Compression (GiB)

Post-Compression (GiB)

Total-Comp Factor (Reduction %)

Pre-Compression Size of data coming into a Data Domain system (before deduplication)

Post Compression After deduplication, the space consumed on a Data Domain system to store data

Total-Comp Factor Cumulative total compression factor

2. Ensure that your Data Domain System is selected in the left navigation pane.

3. Go to Data Management > File System > Summary.27

4. Click on the Refresh link located in right top corner of your Enterprise Manager screen.

5. In the Summary tab, review your Data Domain System space usage.

6. Record the following for Currently Used.


1. From the Training Folder copy the test250m.tar and test500m.tar files and paste them into the B: drive (your Data Domain system). This opens the Copy File window.

2. In the Copy File window, choose the Copy, but keep both files option:

3. Ensure that the files are copied.

Confirm space usage

1. Go to Data Domain Enterprise Manager window.

2. Ensure that your Data Domain system is selected in the left navigation pane.

3. Go to Data Management > File System > Summary.




4. Click on the Refresh link located in right top corner of your Enterprise Manager screen.

5. Under the Summary tab, review your Data Domain System space usage. 28 EMC Data Domain System Administration Course Lab Guide

6. Record the following for Currently Used:

Notice that the Total Comp Factor increases as you copy the files again. If you use backup software to backup to Data Domain system, something similar happens when you perform the second and subsequent full backup jobs.

Create a CIFS share in a Data Domain system

1. In your Windows VM navigate to the B:\ drive.

2. In the B:\ drive window, create a new folder and name it mytest.

3. In the Enterprise Manager, ensure that your Data Domain system is selected in the left navigation pane.

4. Go to Data Management > CIFS > Shares.

5. Under the Shares tab, click the Create button. This opens the Create Share window.

6. In the Create Share window Share Name field, type mytestshare.

7. In Directory Path field, type:/data/col1/backup/mytest




8. Under the Client section, click on the green + sign. This opens Client window.

9. In the Client window, in the Client field, type * .29

This grants access to all clients.

10. Click OK. This closes Client window.

11. In Create Share window ensure that the Max connections is set to Unlimited.

12. Click OK. This closes Create Share window.

13. Go to Data Management > CIFS > Shares.

14. In the Shares tab, ensure that only mytestshare is selected.

15. Review the mytestshare details. 30 EMC Data Domain System Administration Course Lab Guide

16. In your Windows VM, map your mytestshare share as the T: drive.If you need instructions on how to map a network drive refer to the Map a network drive section in this lab. Note that the mapping for the new share will be:\\ddsystem\mytestshare

17. Copy some test files to your CIFS share.

Lab 5.1: Configure Snapshot

Introduction31

Snapshot feature if enabled will save a MTree copy at a specific point in time. In this lab, you configure a snapshot.

Configure a snapshot

1. Open the Computer folder from the desktop.

2. Choose the B: drive.

3. In the B: drive window, create a new folder:

a. Right click on the white space.

b. Select New.

c. Choose Folder.

d. Name the folder test (all lower case).

e. Open the test folder.

Note: Windows folder names are not case sensitive, but Data Domain Enterprise Manager and CLI options are case sensitive. You will be using these folder names in upcoming labs so ensure that you are aware of the exact file names.

4. From the test folder, go to File menu > New > Text Document.

5. Name the text document snap_test1.txt.

6. Open snap_test1.txt.

7. Enter the following in snap_test1.txt

This is a snapshot test file.

8. Save snap_test1.txt.

9. Close snap_test1.txt.

10. Open a browser.


12. In the Enterprise Manager, ensure that your Data Domain system is selected in the left navigation pane.

13. Go to Data Management > Snapshots.

14. From the drop-down menu, ensure that the selected Mtree is:

/data/col1/backup

15. Click Create.

This opens a new Create window.


16. In the Create window, under the name field, type first.

17. Ensure that the selected Mtree is:/data/col1/backup

18. Ensure that the expiration is set to Never Expire.

19. Click OK.

This closes the Create window and opens a new Create Snapshot Status window.

20. In the Create Snapshot Status window, ensure that the snapshot is created.

21. Click Close.

This closes the Create Snapshot Status window and takes you back to Snapshot overview pane.33

22. In the Snapshot overview pane, ensure that the first snapshot you created is listed.

Access a snapshot

1. Go to the B: drive window.

2. Ensure that you are on the root of the B: drive.

3. Click on the address bar where it displays current folder path.

The display on the address bar changes to a text field and displays B:\.

4. Change the path to B:\.snapshot

5. Click Enter.

This displays the snapshot you created in previous steps.

6. Double click the first folder.

7. View your snapshot contents.

Test a snapshot

Create a disaster scenario by deleting a file manually.34 EMC Data Domain System Administration Course Lab Guide

1. On your desktop, double click Computer.

2. In the Computer window, open the B:\ drive.

3. Open the test folder.

4. Select snap_test1.txt file.

5. Click the Delete key to delete the file.

This opens a new Delete File window.

6. In the Delete File window, click Yes.

Recover the file from a snapshot

1. Go to the window where you have the B:\.snapshot\first folder open.

2. Double click and open the test folder.

3. Double click on the snap_test1.txt file to view it from snapshot.

4. Verify the content.

5. Close the file.

6. Right click on the snap_test1.txt file and select Copy.

7. Go to the window where you have the B:\test folder open.

8. Right click on white space.

9. Select Paste.

10. Double click on snap_test1.txt file.

This opens the file.

11. Review the file content.

12. Close the file.

Lab 5.2: Configure Fast Copy

Introduction35

A Fast Copy operation copies files and directory trees of a source directory to a target directory on a Data Domain system. In this lab you will configure Fast Copy using the Enterprise Manager and also recover data from a snapshot using Fast Copy.

Configure Fast Copy

1. Open a browser.

2. Access the Enterprise Manager.

3. In the Enterprise Manager, ensure your Data Domain system is selected in the left Navigation pane.

4. Go to Data Management > File System.

5. Under the File System overview pane, click on the More Tasks drop down menu and select Fast Copy.

This opens a new Fast Copy window.

6. In the Fast Copy window, under the Source text box, enter:/data/col1/backup/.snapshot/first/test

7. Under the Destination text box, enter:/data/col1/backup/fast_test

8. Click OK.

This closes Fast Copy window and opens File Copy Status window.

9. In the Fast Copy Status window, review the Fast Copy status, and ensure its completed successfully.

10. Click Close. 36 EMC Data Domain System Administration Course Lab Guide

This closes Fast Copy Status window and takes you to the File System overview pane.

Access Fast Copy

1. Go to the B: drive window.

2. Ensure you are in the root of the B: drive.

3. Look for the fast_test folder. If you dont see the folder, click on the View menu and select Refresh to refresh the screen.

You should see the fast_test folder.

4. Open the fast_test folder, and review the contents.

You should see the same contents as in the snapshot you stored.

Lab 5.3: Configure Sanitization

Introduction37

This lab covers steps to successfully configure sanitization in a Data Domain system using the CLI. You cannot configure this feature from the Enterprise Manager.

Review installed licenses

1. Open a browser.

2. Access your Data Domain system through the Enterprise Manager.

3. In the Enterprise Manager, ensure your Data Domain system is selected in the left navigation pane.

4. Go to System Setting > Licenses.

5. Review the installed licenses.

6. Ensure that the Retention-Lock license is installed. If it is not installed, inform your instructor.

Configure sanitization

1. After ensuring that the Retention-Lock license is installed, on your Windows desktop, double click on the PuTTY icon.38 EMC Data Domain System Administration Course Lab Guide

2. In the PuTTY configuration window, in the Hostname field, enter the host name or IP address of your Data Domain system.

3. Ensure the connection type is SSH.

4. Click Open.This opens a new window.

5. In the new window, login as sysadmin and enter your assigned password.

6. To start sanitization, in the CLI, enter:

system sanitize start39

7. When prompted for confirmation, enter:

yes

8. Press Enter.

Monitor sanitization

1. To monitor sanitization, in the CLI, enter:

system sanitize watch

2. From here, watch the sanitization progress. When sanitization is complete, it will return to the prompt. If you would like to stop monitoring sanitization, press Ctrl+C.

Lab 5.4: Configure Encryption

Introduction41

This lab covers steps to successfully configure encryption in a Data Domain system using the Enterprise Manager.

Review installed licenses

1. Open a browser.



4. Go to System Settings > Licenses.


6. Ensure the Encryption license is installed. If it is not installed, inform your instructor.

Configure encryption

1. Open a browser.



4. Go to Data Management > File System > Encryption.If Encryption is licensed, the initial status shows Not configured.

5. Under the Encryption tab:42 EMC Data Domain System Administration Course Lab Guide

Click on Configure button. This will open the Configure Encryption window

6. In the Configure Encryption window:

a. In the New Passphrase field, type:abc123

b. In the Confirm New Passphrase field, type:abc123

c. Click Next

Note: Be sure to take care of the passphrase. If the passphrase is lost, you will never be able to unlock the file system and access the data. The data will be irrevocably lost.

7. In the next screen:43

a. Make sure Encryption Algorithm drop down menu is set to AES 256-bit (CBC).

b. Select Apply to existing data check box.

c. Select Restart file system now check box.

d. Click OK. This closes the Configure Encryption window and opens the Configure Encryption Status window.

8. In the Configure Encryption Status window, make sure the status is completed and click Close. This will close the Configure Encryption Status window.

9. In the Enterprise Manager window, under the Data Management > File System tab:44 EMC Data Domain System Administration Course Lab Guide

a. Make sure the Encryption status is Enabled

b. Make sure the File System State is Enabled and running.

Lab 5.5: Configure File System Cleaning

Introduction45

In this lab, you configure file system cleaning in a Data Domain system using the Enterprise Manager.

Configure file system cleaning

1. Open a browser.



4. Go to Data Management > File System > Configuration > Clean Schedule.

Click the Edit button under Clean Schedule.

This opens a new Modify Schedule window.46 EMC Data Domain System Administration Course Lab Guide

5. In the Modify Schedule window, ensure that the Default (Tue at 6am with 50% throttle) option is selected.

6. Click OK.

This closes the Modify schedule window.

Start the cleaning operation


2. Go to Data Management > File System > Clean Status.47

3. Select the Start Cleaning button.

This opens the Start File System Clean window.

4. In the Start File System Clean window, ensure that the Throttle Percentage is set to 50%.

5. Click OK.

This closes the Start File System Clean window and opens the Start File System Clean Status window.

6. In the Start File System Clean Status window, ensure that the File System Clean is completed.48 EMC Data Domain System Administration Course Lab Guide

7. Click Close.

This closes the Start File System Clean Status window.

8. Click the Refresh icon located in right top corner of your Enterprise Manager screen.

9. In the File System pane, under the Clean Status section, ensure that the cleaning finished.

Destroy a file system

Note: This section prepares your Data Domain system for the next lab.

1. In the Enterprise Manager, in the left navigation pane, ensure that your Data Domain system is selected.

2. Go to Data Management > File System > More Tasks drop-down menu.

Select Destroy.

This opens the Destroy File System window.

3. In the Destroy File System window do not select the Write zeroes to disk option.

4. Enter the password for the sysadmin account.49

Click OK.

This closes the Destroy File System window and opens the Destroy File System Status window.

5. In the Destroy File System Status window, ensure that the file system destroy process has completed.

6. Click Close.

Create a file system

Note: This section prepares your Data Domain system for the next lab.


2. Go to Data Management > File System > More Tasks drop-down menu.

3. Select Create File System.

This opens the File System Create window.

4. In the File System Create window, ensure that the Enable file system after creation option is checked.50 EMC Data Domain System Administration Course Lab Guide

Click Next.

You should see the summary screen.

5. Review the Summary screen.

6. Click Finish.

You should see the progress screen.

7. In the Progress screen, ensure that the file system is created and enabled.

8. Click OK.

This closes the File System Create window and displays the File System Overview pane.

9. In the File System Overview pane, under the File System section, ensure that the State is enabled and running.

Lab 6.1: Configure Replication

Introduction51

In this lab, you configure replication and recover replicated data on a Data Domain system using the Enterprise Manager.

Review installed licenses on the source Data Domain system

1. Open a browser.

2. Access your source Data Domain system through the Enterprise Manager.

3. In the Enterprise Manager left navigation pane, ensure that your Data Domain system is selected.



6. Ensure that the REPLICATION license is installed. If it is not installed, inform your instructor.

Prepare the source Data Domain system for replication

1. In your Data Domain Enterprise Manager window, make sure the source Data Domain system is selected in the left pane.

2. In the right pane browse through Data Management > MTree.

3. Under the MTree section, click on the Create button. This will open the Create MTree window.52 EMC Data Domain System Administration Course Lab Guide

4. In the Create MTree window, in the MTree Name field, type repl_source and click OK. This will close the Create MTree window.

5. Under the MTree section make sure /data/col1/repl_source is selected.

6. Under Summary tab, click Create Share. This will open the Create Share window.

7. In the Create Share window:53

a. Under the Share Name field, type repl_source.

b. Under the Clients section, click on the green + sign. This will open the Client window.

c. Under the Client window, in the client name field, type * and click OK. This will close the Client window and will take you back to the Create Share window.

d. In the Create Share window, under Option, make sure Max Connections is set to Unlimited.

e. Click OK. This will close the Create Share window.

8. On your windows VM desktop, double click on the Computer icon to open the computer window.

9. In the Computer window, select Tools and choose Map Network Drive. This opens the Map Network Drive window.

10. In the Map Network Drive window, select Drive S:

11. In the folder field type the network path for your Data Domain systems repl_source share.Example: \\ddsystem\repl_source54 EMC Data Domain System Administration Course Lab Guide

12. Select the check box for Reconnect at logon.

13. Click on the Connect using different user name. This opens the Connect As... window.

14. In the Connect As... window enter the User name sysadmin and your Data Domain system account Password.

15. Click OK. This closes the Connect As... window and takes you back to the Map Network Drive window.

16. Click Finish in the Map Network Drive window.A new window for S: drive appears.

17. On your Windows VM desktop, double click the Training folder to open it.

18. Under the Training folder, double click on the Sample TAR Files folder to open it.

19. You should see two files inside:

a. test250m.tar

b. test500m.tar.

20. Copy both files.

21. Paste both files in to S: drive.

This opens a file transfer window. After the file transfer finishes, the window closes.

22. Write the file names.

Add the replication target Data Domain system

1. Get your replication-target Data Domain system hostname from your instructor.

2. Write your replication-target Data Domain hostname:

3. Get your replication-target Data Domain system sysadmin-account password from your instructor.

4. Write your password for your replication-target Data Domain system:

5. In your Enterprise Manager window, in the left pane, click the Add icon. 55

This opens the Add System(s) window.

6. In the Add System(s) window System Name: field, enter your replication target Data Domain system hostname (that you obtained earlier in this lab).

7. In the Administration Credentials section Password field, enter the sysadmin account password (that you obtained earlier in this lab).

8. Click OK.

This opens the Verify Certificate window.

9. In the Verify Certificate window, click OK.

This closes the Add System(s) and Verify Certificate windows.

10. In the Enterprise Manager left pane, ensure that your replication source and target Data Domain systems are listed.

Review installed licenses on the target Data Domain system

1. In the Enterprise Manager left navigation pane, ensure that your target Data Domain system is selected.56 EMC Data Domain System Administration Course Lab Guide



4. Ensure that the REPLICATION license is installed. If its not installed, inform your instructor.

Configure replication

1. In the Enterprise Manager left navigation pane, ensure that your source Data Domain system is selected.

2. Go to Replication > Summary.

3. Under the Summary tab, click the Create Pair button.

This opens the Create Pair window.57

4. In the Create Pair window, ensure that the General tab is selected.

5. Under the General tab, from the Replication Type drop-down menu, select MTree.

6. In the Replication Details section, from the Source System drop-down menu, select your source Data Domain System.

7. In the Source Path field, enter:

repl_source

This is the MTree you created earlier in this lab.

8. From the Destination System drop-down menu, select your destination Data Domain System.

9. In the Destination Path field, type;

repl_your first name_your last name

For Example: repl_john_peter

Note: All students in this course are using the same Data Domain system as the replication destination Data Domain System.

10. Review the details.

11. Click OK.

This closes the Create Pair window and opens the Create Pair Status window.

12. In the Create Pair Status window, observe the Create MTree Replication progress.

13. An Information window reamains open while the Create MTree Replication is in progress. Do not click OK. Please wait until Create MTree Replication completes 100% in the background.58 EMC Data Domain System Administration Course Lab Guide

14. After confirming that Create MTree Replication completes 100%, click OK.

This closes the Create Pair Status window and displays the Replication Summary tab.

15. In the Summary tab, review the table.

16. Ensure that the Time to Completion displays as Completed.

This confirms the successful configuration of replication between two Data Domain systems.

Verify replication

1. In your Data Domain Enterprise Manager window, make sure that the destination Data Domain system is selected in the left pane.

2. In the right pane browse through Data Management > MTree.

3. Under the MTree section make sure that the replication destination MTree is selected.For Example: /data/col1/repl_john_peter

4. Under the Summary tab, click on Create Share. This will open the Create Share window.

5. In the Create Share window,

a. Under the Share Name field, type repl_your first name_your last name.For Example: repl_john_peter

b. Under the Clients section, click on the green + sign. This will open the Client window.

c. Under the Client window, in the client name field, type * and click OK. This will close the Client window and will take you back to the Create Share window.

d. In the Create share window, under Option, make sure Max Connections is set to Unlimited.

e. Click OK. This will close the Create Share window

6. On your windows VM desktop, double click the Computer icon to open the computer window.

7. In the Computer window, select Tools and choose Map Network Drive. This opens the Map Network Drive window.59

8. In the Map Network Drive window, Choose the R: Drive.

9. In the folder field, type the network path for the replication target MTree (for example: repl_john_peter) on your destination Data Domain system:

\\ddsystem\repl_john_peter

10. Check the box for Reconnect at logon.

11. Click on Connect using different user name.

This opens the Connect As window.

12. In the user name field type:

sysadmin

13. In the password field type:

password for sysadmin account of your Data Domain system

14. Click OK.

This closes the Connect As window and takes you back to the Map Network Drive window.

15. Click Finish in the Map Network Drive window.

A new window for R:\ drive will appear.

16. In the R:\ drive window, confirm that the files you recorded earlier in this lab are present.

If all the files are present, this confirms that all the files from the source Data Domain 60 EMC Data Domain System Administration Course Lab Guide

system were successfully replicated to the destination Data Domain system.

Lab 7.1: Configure DD Boost with EMC NetWorker

Introduction61

In this lab, you configure DD Boost on a Data Domain system using the Enterprise Manager. You also integrate a Data Domain System with EMC NetWorker using DD Boost.

Review installed licenses on the source Data Domain system

1. Open a browser.

2. Access your Data Domain systems through the Enterprise Manager.

3. In the Enterprise Manager, in the left navigation pane, ensure that your source Data Domain system is selected.

4. In the right navigation pane, select the System Settings tab.

5. Under the System Settings tab, select the Licenses tab.


7. Ensure that the DDBOOST and REPLICATION licenses are installed. If they are not installed, inform your instructor.

Prepare the source Data Domain system for DD Boost

In this section you prepare the source Data Domain system for DD Boost.


2. In the right navigation pane, select the Data Management tab.

3. Under the Data Management tab, select the DD Boost tab.

4. Under the DD Boost tab, check the DD Boost Status, if it is disabled, click Enable.

This opens the Enable DD Boost window.


5. In the DD Boost window, from the Existing User Name drop down menu, choose sysadmin.

6. Click OK.

7. In the DD Boost window, select the Storage Units tab.

8. Under the Storage Units tab, click Create Storage Unit.

This opens the Create Storage Unit window.

9. In the Create Storage Unit window, under the Name filed, type:

ddboost_source_su

10. Click OK.

11. In the Storage Unit window, ensure that the ddboost_source_su storage unit is selected.

12. Review the details.63

Review the installed licenses on the target Data Domain system

1. In the Enterprise Manager, in the left pane, double-click on the target Data Domain system.

Note: Your target Data Domain system is the same target Data Domain system you used in the Replication lab.

2. In the Enterprise Manager, in the left navigation pane, ensure that your target Data Domain system is selected.

3. In the right navigation pane, select the System Settings tab in right navigation pane.


5. Review the installed licenses and ensure that the DDBOOST and REPLICATION licenses are installed. If they are not installed, inform your instructor.

Prepare the target Data Domain system for DD Boost

In this section you prepare the target Data Domain system for DD Boost.64 EMC Data Domain System Administration Course Lab Guide


Note: You might get Unable to process next line of storage-unit summary temp file error message. You can click OK and safely ignore this error message.



4. Under the DD Boost tab, check the DD Boost Status, if Disabled, click Enable.


5. In the DD Boost window, from the Existing User Name drop-down menu, choose sysadmin.

6. Click OK.





ddboost_your first name_your last name_su

10. Click OK.

For Example: ddboost_john_peter_su

Note: All students are using the same Data Domain system as the target system. So to easily identify your information, follow the above naming convention.

11. In the Storage Unit window, ensure that the ddboost_john_peter_su storage unit is selected.

12. Review the ddboost_john_peter_su details.65

Add source Data Domain system information in NetWorker

1. On your Windows VM desktop, double-click on the NetWorker Management Console icon to open it.

This opens the NetWorker Management Console Login window.

Note: This operation takes 2 - 3 minutes.

2. In the NetWorker Management Console Login window, in the User Name field, type:

administrator

3. In the Password field type:

password

4. Click OK.

This opens the NetWorker Management Console window.

5. In the NetWorker Management Console window, select the Enterprise tab.

6. Under the Enterprise tab, select dd01_win.

7. In right pane select NetWorker.

8. Right-click and select Launch Application.

This opens NetWorker Administration window.


9. In the NetWorker Administration window, select the Devices tab.

10. Under the Devices tab, on the left pane, select Data Domain Systems.

11. In the right pane, right-click and select New Device Wizard.

This opens the Device Configuration Wizard.

12. In the Device Configuration Wizard, in Select the Data Domain Type screen, select Data Domain

13. Click Next.

14. In the Data Domain Configuration Checklist screen, do not select an option.

15. Click Next.

16. In the Configuration Options screen, select Create a New Data Domain System option.

17. Enter your source Data Domain system host name.

18. In the Data Domain OST Username field type:

sysadmin67

19. In the Data Domain OST Password field enter your sysadmin account password.

20. Click Next.

21. In the Select Folders for Devices screen, check the box for ddboost_source_su

22. Click Next.

23. In the Configure Pools screen:

a. Ensure that the Configure Media Pools for devices is checked.

b. Ensure that the Pool Type is Backup.

c. Select Create and use a new Pool and type:

ddboostsourcepool

d. Ensure that the Label and Mount device after creation is checked.

e. Click Next.

24. In the Select Storage Nodes screen:

a. Make sure Use an existing storage node option is selected.

b. Click Next.

25. In the SNMP Monitoring Options screen:

a. Un-check Gather usage information.

b. Un-check Receive SNMP trap events.

c. Click Next.

26. In the Review Configuration Settings screen, review the information.68 EMC Data Domain System Administration Course Lab Guide

27. Click Configure.

This opens the Labelling volume progress bar. This operation takes around two minutes to complete.

28. In the Check Results screen, review the information.

29. Click Finish.

This closes Device Configuration Wizard window.

30. In the NetWorker Administration window, in left pane, expand Data Domain Systems and select your source Data Domain System.

This displays information in the right pane.

31. Review the information.

Add target Data Domain system information in NetWorker

1. In the NetWorker Administration window, under the Devices tab, in the left pane, select Data Domain Systems.

2. In the right pane, right-click and select New Device Wizard.

This opens Device Configuration Wizard.

3. In the Device Configuration Wizard, in the Select the Data Domain Type screen, select Data Domain.

4. Click Next.

5. In the Data Domain Configuration Checklist screen, do not select an option.

6. Click Next.

7. In the Configuration Options screen, select Create a New Data Domain System option and type your target Data Domain System host name.

8. In the Data Domain OST Username field type:

sysadmin

9. In the Data Domain OST Password field type your sysadmin account password.69

10. Click Next.

11. In the Select Folders for Devices screen, check ddboost_john_peter_su.

12. Click Next.

13. In the Configure Pools screen:

a. Ensure that the Configure Media Pools for devices is checked.

b. Ensure that the Pool Type is Backup Clone.

c. Select Create and use a new Pool and type:

ddboostfirst name last namepool

For Example: ddboostjohnpeterpool

d. Ensure that the Label and Mount device after creation is checked.

e. Click Next.

14. In the Select Storage Nodes screen, click Next.

15. In the SNMP Monitoring Options screen:

a. Un-check Gather usage information.

b. Un-check Receive SNMP trap events.

c. Click Next.

16. In the Review Configuration Settings screen:

a. Review information.70 EMC Data Domain System Administration Course Lab Guide

b. Make sure the Pool Type is Backup Clone.

Note: If the Pool Type is not Backup Clone, click on Back button to navigate to Configure Pools screen and follow instructions above to configure the Pool Type as Backup Clone.

17. Click Configure.

This opens the Labelling volume progress bar. This operation takes around two minutes to complete.

18. In the Check Results screen, review the information.

19. Click Finish.

This closes Device Configuration Wizard window.

20. In the NetWorker Administration window, in the left pane, expand Data Domain Systems and select your target Data Domain System.

This displays information in the right pane.


Configure NetWorker to perform a backup to the source Data Domain system

1. In the NetWorker Administration window, select the Configuration tab.

2. Under the Configuration tab, in the left pane, select Clients.

3. In the right pane, right-click on white space, choose Client Backup Configuration and select New.

This opens the Client Backup Configuration window.

4. In the Client Backup Configuration window, in the Specify the Client Name screen, in the Client name field enter:

dd01_win

5. Click Next.71

6. In the Specify the Backup Configuration Type screen, click Next.

7. In the Specify the Backup Options screen:

a. Set the Deduplication to Data Domain Backup.

b. Ensure the Checkpoint is not Enabled.

c. From the Target Pool drop-down menu, select your source DD Boost pool:

ddboostsourcepool

d. Click Next.

8. In the Select Files to Backup screen:

a. Click the + sign and expand dd01_win.

b. Un-check dd01_win.

c. Click the + sign and expand the C: drive.

d. Click the check box for the Troubleshooting folder and check boxes for test250m.tar and test 500m.tar files.72 EMC Data Domain System Administration Course Lab Guide

9. Click Next.

10. In the Select the Client Properties screen, click Next.

11. In the Choose the Backup Group screen, click Create a new group.

12. Type:

ddboostgroup

13. Click Next.

14. In the Specify the Storage Node Options screen, click Next.

15. In the Backup Configuration Summary screen, click Create.

16. In the Check Results screen, click Finish.

This closes the Client Backup Configuration window.

17. In the NetWorker Administration window, select the Media tab.

18. Under the Media tab left pane, select the Media Pools and on the right side pane, double-click ddboostsourcepool.

This opens the Properties window for ddboostsourcepool.73

19. In the Properties window, under Data Source section, select the ddboostgroup.

20. Click OK.

This closes the Properties window.

Configure NetWorker to perform a backup clone to the target Data Domain system

1. In the NetWorker Administration window, select the Configuration tab.

2. Under the Configuration tab, in the left pane, select Clones.

3. In the right pane, right-click on white space, and choose New.

This opens Create Clone window.74 EMC Data Domain System Administration Course Lab Guide

4. In the Create Clone window:

a. Ensure that the General tab is selected.

b. Under the Name field, type name in the following format:

yourfirstnameyourlastnameclone

For example: johnpeterclone

c. From the Write clone data to pool drop down menu, choose:

ddboostyourfirstnameyourlastnamepool

For example: ddboostjohnpeterpool

d. Select the Save Set Filters tab.

e. Under the Save Set Filters tab, under Save Set Filter Options, in the Groups section, check ddboostgroup.

f. Click OK.

This closes Create Clone window.75

5. Under the Configuration tab, in left pane ensure that Clones is selected.

6. In the right pane, review details for the clone you created.

Perform backup to source Data Domain system

1. In the NetWorker Administration window, select the Monitoring tab.

2. Under the Monitoring tab, select the Groups tab.

3. Under the Groups tab, right-click on ddboostgroup and select Start.

This opens Question window.

4. In the Question window, select Yes.

This closes Question window and initiates the backup job.

5. To monitor the backup job progress, under the Groups tab, right-click on ddboostgroup and choose Show Details.

This opens Details window for ddboostgroup.76 EMC Data Domain System Administration Course Lab Guide

6. In the Details window, monitor Status. It will take around 2 - 3 minutes to complete this job.

7. After Status displays Succeeded and the backup job is 100% complete, click OK.

Perform a backup clone to the target Data Domain system

1. In the NetWorker Administration window, select the Monitoring tab.

2. Under the Monitoring tab, select the Clones tab.

3. Under the Clones tab, right-click on your_first_nameyour_last_nameclone.

For example: johnpeterclone

4. Select Start.

This opens Question window.

5. In the Question window, click Yes.

This closes the Question window and initiates the backup clone job.

6. To monitor the backup clone job progress, under the Clone tab, right-click on johnpeterclone and choose Show Details.

This opens the Details window for johnpeterclone.77

7. In the Details window, monitor Status. It could take around 2 minutes to complete this job. If the screen doesnt refresh automatically click on the Refresh button.

8. After the Status displays Successful, click OK.

Verify Space Usage and File System Stats on Data Domain Systems

1. In the Enterprise Manager, in the left pane, ensure that the source Data Domain System is selected.


2. Go to Data Management > DD Boost > Activities.


4. Under the DD Boost tab, select the File Replication Stats tab.


6. Repeat the above steps on the target Data Domain system.


Lab 7.2: Configure DD Boost with Symantec NetBackup

Introduction79

In this lab, you configure DD Boost on a Data Domain system using the Enterprise Manager. You also integrate a Data Domain System with Symantec NetBackup using DD Boost.

Create a NetBackup Windows 2008 image

1. From the VMware vCenter Lab Manager Workspace, clone the DDSA5.1Netbackup7.0 image to a new name.

2. Select the image you just cloned and named.

3. Select Deploy with Defaults.

4. Log in to the new deployed image.username: administratorpassword: abc123

Review Installed Licenses on the Source Data Domain System

1. Open a browser.

2. Access your Data Domain systems through the Enterprise Manager.


4. In the right navigation pane, select the System Settings tab.



7. Ensure that the DDBOOST and REPLICATION licenses are installed. If they are not installed, inform your instructor.

Prepare the Source Data Domain System for DD Boost

In this section you prepare the source Data Domain system for DD Boost.80 EMC Data Domain System Administration Course Lab Guide




4. Under the DD Boost tab, check the DD Boost Status, if it is disabled, click Enable.


5. In the DD Boost window, from the Existing User Name drop down menu, choose sysadmin.

6. Click OK.





nbu_source_su

10. Click OK.

11. In the Storage Unit window, ensure that the nbu_source_su storage unit is selected.

12. Review the details.81

Review the Installed Licenses on the Target Data Domain System

1. In the Enterprise Manager, in the left pane, double-click on the target Data Domain system.

Note: Your target Data Domain system is the same target Data Domain system you used in the Replication lab.


3. In the right navigation pane, select the System Settings tab in the right navigation pane.


5. Review the installed licenses and ensure that the DDBOOST and REPLICATION licenses are installed. If they are not installed, inform your instructor.

Prepare the Target Data Domain System for DD Boost

In this section you prepare the target Data Domain system for DD Boost.82 EMC Data Domain System Administration Course Lab Guide





4. Under the DD Boost tab, check the DD Boost Status, if Disabled, click Enable.


5. In the DD Boost window, from the Existing User Name drop-down menu, choose sysadmin.

6. Click OK.





nbu_your first name_your last name_su

10. Click OK.

For Example: nbu_john_peter_su

Note: All students are using the same Data Domain system as the target system. So to easily identify your information, follow the above naming convention.

11. In the Storage Unit window, ensure that the nbu_john_peter_su storage unit is selected.

12. Review the nbu_john_peter_su details.83

Verify and install a Data Domain plug-in on your Windows host

1. Access the new Windows host DDSA5.1Netbackup7.0 that you cloned.

2. Open the Windows CLIStart > Run > Type cmd > Click OK

3. Ensure that the Data Domain plug-in is installed by entering:

bpstsinfo -pi

Review the output and make sure Prefix is Data Domain and Label is Data Domain Plug-in.

Note: The above command lists the Netbackup plug-ins installed in the Windows system.

4. If the Data Domain plug-in isnt installed, install it using following steps:

a. Go to Start -> Run -> services.msc > Click OK.84 EMC Data Domain System Administration Course Lab Guide

b. Select the NetBackup Remote Manager and Monitor Service > Right click > Select Stop.

c. Go to Desktop > Training > OST_2.2.1.1-168278_OST_windows folder.

d. Run libstspiDataDomainSetup.exe.

e. In the Open File - Security Warning window, select Run.

f. In the Data Domain OST plug-in Setup window, Select I Agree > Click Next > Click Install > Click Close.This installs the Data Domain plug-in.

5. In Windows CLI, ensure that the Data Domain plug-in is installed by entering:

bpstsinfo -pi

Review the output and make sure Prefix is Data Domain and Label is Data Domain Plug-in.

6. Start > Run > services.msc.

7. Start the NetBackup Remote Manager and Monitor service.

Configure the source Data Domain system as storage server in NetBackup

1. From your windows VM desktop, double click NetBackup Administration Console icon and open the NetBackup GUI console.

2. From the left navigation pane, select dd01_win (the master server).

3. From the wizard menu, select the Configure Disk Storage Servers.85

4. This opens Storage Server Configuration Wizard. In Storage Server Configuration Wizard:

a. In the Welcome screen, Click Next.

b. In the Add Storage Server screen, from disk storage type drop down menu, choose OpenStorage.

c. In the next screen, specify:

storage server type DataDomain86 EMC Data Domain System Administration Course Lab Guide

Click Next.

d. In the Storage Server Configuration Summary screen, click Next.

e. In the Storage Server Creation Status screen, make sure the tasks are successfully completed. Click Next.

(Its case sensitive. Type as shown above with no space between DataDomain)

storage server name Specify your Data Domain system host name

media server dd01_win

user name sysadmin

password abc123

f. Click Next again to open Disk Pool creation window.

5. In the Disk Pool Configuration Wizard:87

a. In the Welcome screen, click Next.

b. In the Disk Pool Type screen, select OpenStorage (DataDomain) and click Next.

c. In the Select Storage Server screen, select your source Data Domain system and click Next.

d. In the Select Volumes screen, select nbu_source_su check box and click Next.

e. In the Disk Pool Properties screen, in disk pool name field type:ddboost_source_dpClick Next.

f. In the Summary screen click Next.

g. In the Disk Pool Creation screen, make sure the task is completed successfully and click Next.

h. In the Storage Unit creation screen, make sure Create a Storage Unit that uses ddboost_source_dp check box is selected and click Next.

i. In the Storage Unit Creation screen, in Storage unit name field, type:ddboost_source_suClick Next.

j. In the Finished screen, click Finish.

Configure and test the NetBackup backup policy

1. In the NetBackup Administration Console, select Create a Backup Policy.88 EMC Data Domain System Administration Course Lab Guide

2. In the Welcome to the Backup Policy Configuration Wizard screen, click Next.

3. In the Policy Name and Type screen, under the Policy name field, type:ddboost_policyClick Next.

4. In the Client List screen:

a. Click Add.

b. Click the small Computer icon. This opens the Browse for computer window.

c. In the Browse for computer, expand Local Network Neighbourhood and select DD01_WIN, click OK.

d. In the Client List window, click in the white area. This auto-fills the Hardware and Operating System information.

e. Click Next.

5. In the Files screen: 89

a. Click Add.

b. Click the small Remote Folder icon. This opens the Browse window.

c. In the Browse window double click the C: drive, select the Troubleshooting folder and click OK.

d. In the Files screen, click in the white area.

e. Click Next.

6. In the Backup Type screen, make sure Full Backup, Incremental Backup and User Backup check box is selected and click Next.

7. In the Rotation screen, click Next.

8. In the Start Window screen, click Next.

9. Click Finish.

10. In the NetBackup Administration Console window, expand NetBackup Management > Policies > select ddboost_policy:

a. Right click and choose Manual Backup.90 EMC Data Domain System Administration Course Lab Guide

b. In the Manual Backup window, click OK.

c. Click OK.

11. In the NetBackup Administration Console, select Activity Monitor to monitor the backup progress.91

12. While the backup is running, navigate to the Enterprise Manager window, in the left pane, ensure that the source Data Domain System is selected.






Note: The first time the backup is run, pre-compression, post-compression, and network statistics should be similar. If backup data is already on the Data Domain system, or the backup is being run for a 2nd time, pre-compression will be high and post-compression and network statistics will be very low due to DD Boost DSP.

Configure the destination Data Domain system as storage server in NetBackup

1. In the Netbackup Administration console, from the left navigation pane, select dd01_win (the master server).

2. From the wizard menu, select the Configure Disk Storage Servers.92 EMC Data Domain System Administration Course Lab Guide

3. This opens the Storage Server Configuration Wizard. In Storage Server Configuration Wizard:

a. In the Welcome screen, Click Next.

b. In the Add Storage Server screen, from disk storage type drop down menu, choose OpenStorage.

c. In the next screen, specify:

storage server type DataDomain93

Click Next.

d. In the Storage Server Configuration Summary screen, click Next.

e. In the Storage Server Creation Status screen, make sure the tasks are successfully completed. Click Next.

(Its case sensitive. Type as shown above with no space between DataDomain)

storage server name Specify your Data Domain system host name

media server dd01_win

user name sysadmin

password abc123

f. Click Next again to open Disk Pool creation window.

4. In the Disk Pool Configuration Wizard:94 EMC Data Domain System Administration Course Lab Guide

a. In the Welcome screen, click Next.

b. In the Disk Pool Type screen, select OpenStorage (DataDomain) and click Next.

c. In the Select Storage Server screen, select your destination Data Domain system and click Next.

d. In the Select Volumes screen, select nbu___su check box and click Next.

e. In the Disk Pool Properties screen, in the disk pool name field type:ddboost_destination_dpClick Next.

f. In the Summary screen, click Next.

g. In the Disk Pool Creation screen, make sure the task is completed successfully and click Next.

h. In the Storage Unit creation screen, make sure Create a Storage Unit that uses ddboost_destination_dp check box is selected and click Next.

i. In the Storage Unit Creation screen, in the Storage unit name field, type:ddboost_destination_suClick Next.

j. In the Finished screen, click Finish.

Configure the NetBackup Storage Life Cycle Policy

1. Go to the NetBackup Management Console > Storage > Storage Life Cycle Policies.95

2. Right click on the Storage Lifecycle Policies and choose New Storage Lifecycle Policy. This opens the New Storage Lifecycle Policy window.

3. In the New Storage Lifecycle Policy window:

a. Under the Storage lifecycle policy name field enter:ddboost_slp

b. Click Add. This opens the New Storage Destination window.96 EMC Data Domain System Administration Course Lab Guide

4. In the New Storage Destination window:

a. Set the Use for option to Backup.

b. From the Storage Unit drop down menu, choose ddboost_source_su.

c. Click OK. This will close the New Storage Destination window and take you back to New Storage Life Cycle Policy window.

5. In the New Storage Lifecycle Policy window:

a. Make sure you can see the storage destination you just added.97

b. Click on Add. This will open the New Storage Destination window.

6. In the New Storage Destination window:

a. Set the Use for option to Duplication.

b. From the Storage Unit drop down menu, choose ddboost_destination_su.

c. Click OK. This will close the New Storage Destination window and take you back to New Storage Life Cycle Policy window.

7. In the New Storage Lifecycle Policy window,

a. Make sure you can see both the storage destinations you just added.98 EMC Data Domain System Administration Course Lab Guide

b. Click on OK. This will close the New Storage Lifecycle Policy window.

Modify and test the NetBackup backup policy

1. Go to the NetBackup Administration Console > NetBackup Management > Policies.

2. Right Click on the ddboost_policy > select Change. This will open the Change Policy window.

3. In the Change Policy window:

a. From the Policy Storage drop down menu, choose ddboost_slp.99

b. Click OK. This will close the Change Policy window.

4. Before starting the updated Backup Policy create a LIFECYCLE_PARAMETERS file.

a. Go to the Windows sub-directory:

C:\Program Files\Veritas\NetBackup\db\config

b. Select File > New > Text Document and name it LIFECYCLE_PARAMETERS.

Note: The filename should be LIFECYCLE_PARAMETERS with no file extension.

c. Enter the following text in the LIFECYCLE_PARAMETERS file:

MAX_MINUTES_TIL_FORCE_SMALL_DUPLICATION_JOB 1

This updates the default 30-minute wait between a backup job and a duplication job to only 1 minute.

5. In the NetBackup Administration Console window, expand NetBackup Management > Policies > select ddboost_policy.

a. Right click and choose Manual Backup.100 EMC Data Domain System Administration Course Lab Guide

b. In the Manual Backup window, click OK.

c. Click OK.

6. In the NetBackup Administration Console, select the Activity Monitor to monitor the backup progress.101

7. While the backup is running, navigate to the Enterprise Manager window, in the left pane, ensure that the source Data Domain System is selected.






12. Repeat the above steps on the target Data Domain system.


End of Configure DD Boost with Symantec NetBackup lab.

Lab 9.1: Monitor a Data Domain System Using SNMP

Introduction103

In this lab, you configure SNMP in Data Domain system using the Enterprise Manager.

Configure SNMP

1. In your windows VM desktop, open a browser.

2. Access your Data Domain system Enterprise Manager.

3. In the Enterprise Manager left navigation pane, ensure your Data Domain system is selected.

4. Go to System Settings > General Configuration > SNMP.

5. Under the SNMP tab, ensure that the status is enabled.

6. If the status is enabled, go to step 10.

7. If the status is disabled, click the Enable button.

This opens the Enable SNMP window in the Enable SNMP window.104 EMC Data Domain System Administration Course Lab Guide

8. Click OK.

This closes the Enable SNMP window and opens the Enable SNMP Status window.

9. In the Enable SNMP Status window, ensure that Enable SNMP... is Completed.

10. Click Close. The Enable SNMP Status window closes, and you see the SNMP tab screen.

11. Under SNMP Properties section, click the Configure button. This opens the Configure SNMP Properties window.

12. In Configure SNMP Properties window:

a. Under SNMP System Location, type Training.

b. Under SNMP System Contact, type Admin.

c. Click OK. This closes the Configure SNMP Properties window.

13. Go to the SNMP V2C Configuration > Communities section, and click the Create button.

Note: Make sure you are clicking on the Create button under the SNMP V2C 105

Configuration section and not the button in the SNMP V3 Configuration section.

This opens the Create SNMP V2C Community window.

14. In the Community field, type public

15. For Access, select the read-only radio button and click OK. This closes the Create SNMP V2C Community window.

16. Repeat the above steps to configure read-write community string. Under the SNMP V2C Configuration section, click the Create button. This opens the Create SNMP V2C Community window.106 EMC Data Domain System Administration Course Lab Guide

17. In the Community field, type private.

18. For Access, select the read-write radio button and click OK. This closes the Create SNMP V2C Community window.

19. Under the SNMP V2C Configuration Trap Hosts section, click the Create button. This opens the Create SNMP V2C Trap Host window.

20. From your VMware vCenter Lab Manager window, record your Windows VM External IP address:

Note: The VMware vCenter Lab Manager Internet Explorer window is on your local workstation or laptop. It includes the vCenter Lab Manager menu and window frame

around your virtual lab system.107

21. In the Create SNMP V2C Trap Host window Host field, enter your Windows VM External IP address.

22. Click OK.

This closes the Create SNMP V2C Trap Host window.

Monitor a Data Domain system using SNMP

In this lab setup, you use an SNMP MIB browser (an SNMP utility) for Windows as an example. There are other SNMP utilities that you can use for monitoring Data Domain system using SNMP.

1. On your Windows VM desktop, double-click the MIB Browser icon.

This opens the iReasoning MIB Browser window.

2. Click the Address field.

3. Enter your Data Domain system IP address or hostname.

4. Confirm that .1.3 is displayed in the OID field.

5. Confirm that Get Next is displayed in the Operations field.

Windows VM External IP address:

6. Click Go.108 EMC Data Domain System Administration Course Lab Guide

7. Note the results in the Result Table.

8. Click Go again.

9. Note the results in the Result Table.

10. Click Go several more times, and note the results in the Result Table.

Lab 9.2: Monitor a Data Domain System Using Syslog

Introduction109

In this lab you configure syslog (remote logging) on a Data Domain system using PuTTY. You will also use a windows-based Kiwi Syslog Server to practice remote logging.

Configure a Kiwi Syslog application

In this section you prepare a Kiwi Syslog application to receive system logs from a Data Domain system.

1. From your VM Windows desktop, double click the Kiwi Syslog Daemon icon.

This opens Kiwi Syslog Server window.

2. In Kiwi Syslog Server window, select the File pull-down menu.

3. Choose Setup.

This opens Kiwi Syslog Server Setup window.

4. In Kiwi Syslog Server Setup window, under:

Rules > Default > Actions

Ensure that the Log to file option is checked.

5. Without unchecking Log to file option, click on the text Log to file.

This changes the display on the right pane. 110 EMC Data Domain System Administration Course Lab Guide

6. Record the Path and file name of log file.

7. In the Kiwi Syslog Server Setup window, click OK.

This closes Kiwi Syslog Server Setup window.

8. From your lab manager window, record your Windows VM External IP address

Log file path and name:

Windows External IP address:

Configure remote logging in a Data Domain system

1. On your windows desktop, double click on the PuTTY icon to invoke the application.111

2. In the PuTTY Configuration window Hostname field, enter the host name or IP address of the Data Domain system assigned to you.

3. Ensure that the connection type is SSH.

4. Click Open.

This opens a new window.

5. In the new window, login as sysadmin.


7. From your PuTTY session, add the remote logging device to the logging host list by entering:112 EMC Data Domain System Administration Course Lab Guide

log host add

8. In the CLI, to enable the remote logging on Data Domain system, enter:

log host enable

9. In the CLI, to display the current remote logging configuration enter:

log host show

10. Ensure the remote logging is enabled and your windows VM External IP address is configured as remote logging host.

Test remote logging

1. In your PuTTY window, to verify whether the Data Domain file system is enabled and running, type:

filesys status

2. In the Kiwi Syslog Daemon window, monitor the activity.

You should see the Data Domain console actions being captured.

3. In your PuTTY window, to test remote logging, enter Data Domain commands and monitor the activity in the Kiwi Syslog Daemon.

4. On your Windows VM desktop, double click on the Computer icon and go to the folder where the Kiwi Syslog Server log file is stored. (This information was obtained earlier in this lab.)113

5. Open the log file and review it.

Note: The default name of the log file is SyslogCatchAll.txt

6. Review the log file and compare the information to the Kiwi Syslog messages. They will be the same.

7. Close the log file.

Lab 9.3: Manage Log Files

Introduction115

In this lab, you manage log files in a Data Domain system using the Enterprise Manager.

Manage Log Files

1. Open a browser.


3. In the Enterprise Manager left navigation pane, ensure that your Data Domain system is selected.

4. Go to Maintenance > Logs.

5. Under the Logs tab, review all the listed log files.

6. Under the Logs tab, right click on the messages file and select Save Target As.

This opens the Save As window.

7. In the Save As window, ensure that the file is stored in the desktop.

8. Change the file name to messages.txt.

9. Click Save.

This closes the Save As window.

10. Go to your Windows VM desktop and locate the messages.txt file.

11. Right click on the messages.txt file, under Open With, select WordPad.

This opens the file in WordPad.

12. In the WordPad window, scroll through the file and review the messages log file.

13. Close the messages log file.116 EMC Data Domain System Administration Course Lab Guide

Lab 9.4: Autosupport and Support Bundle

Introduction117

In this lab, you configure, review, and test autosupport in a Data Domain system using the Enterprise Manager and the CLI.

Verify the mail server configuration

1. Open a browser.


3. In the Enterprise Manager, in the left navigation pane, ensure your Data Domain system is selected.

4. Go to System Settings > General Configuration > Mail Server.

5. Under the Mail Server tab, ensure that the Mail Server is 10.127.22.55 (the IP address of the mail server in this lab).

6. If the Mail Server is configured properly, skip the next steps and go to Configure autosupport.

7. If the Mail Server is not set to 10.127.22.55, go to General Configuration.

8. Click on the More Tasks drop-down menu.

9. Select Set Mail Server. This opens the Set Mail Server window.

10. In the Set Mail Server window, under the Mail Server field, type:10.127.22.55

11. Click OK.

This closes the Set Mail Server window.

Configure autosupport

Note: If you are performing this lab from an EMC facility on the EMC network or EMC classroom network you will be blocked from accessing any webmail (for 118 EMC Data Domain System Administration Course Lab Guide

example, Yahoo, Gmail, etc) accounts. You may use your company email address to send the autosupport email and you can check it on your smart phone or after class from a network outside EMC.

If you have an EMC email account (EMC employee/Partner), you can check your emc.com email account. The message may take few minutes to get delivered to your inbox.

1. In the Enterprise Manager, in the left navigation pane, ensure your Data Domain system is selected.

2. Go to Maintenance > Support > Autosupport.

3. Under the Autosupport Mailing List section, click the Configure button.

This opens the Configure Autosupport Subscribers window.

4. In the Configure Autosupport Subscribers window, click the green + button.

This opens Email window.

5. In the Email window, type your email address.

6. Click OK. 119

This closes the Email window.

7. In the Configure Autosupport Subscribers window, click OK.

This closes the Configure Autosupport Subscribers window and displays the Autosupport tab.

8. Under the Autosupport tab, under the Autosupport Mailing List section, ensure that your email address is listed.

View an autosupport report

1. In the Enterprise Manager go Maintenance > Support > Autosupport.

2. In the Autosupport Reports section, right click on the autosupport link and select Save Target As.

This opens Save As window.

3. In the Save As window:

a. Ensure that the file is stored on the Desktop.

b. Change the file name to autosupport.txt

c. Click Save.

This closes the Save As window.

4. Go to your Windows VM desktop and locate the autosupport.txt file.

5. Right click on autosupport.txt file, under Open With select WordPad.

This opens file in WordPad.

6. In the WordPad window, scroll through the file and review the autosupport report.

7. Close the autosupport report file.

Test Autosupport

1. On your windows desktop, double click the PuTTY icon.

2. In the PuTTY Configuration window Hostname field, enter the host name (or IP address) of the Data Domain system assigned to you.

3. Ensure the connection type is SSH.

4. Click Open. 120 EMC Data Domain System Administration Course Lab Guide

This opens a new window.

5. In the new window, log in as sysadmin.


7. To test autosupport, in CLI, type:

autosupport test email your_email_address

Example:autosupport test email [email protected]

8. Check your email inbox. You should see an autosupport test email.

Reset an autosupport email list

In this section you will remove your email address from a daily autosupport mailing list. This stops daily autosupport emails from being sent to you.

1. In the Enterprise Manager left navigation pane, ensure your Data Domain system is selected.

2. Go to Maintenance > Support > Autosupport.

3. Under the Autosupport Mailing List section, click the Configure button.

This opens the Configure Autosupport Subscribers window.

4. In the Configure Autosupport Subscribers window:121

a. Select the c

data domain lab guide

Documents

file system cleaning

monitor system activity

emc networker

copy files

installed licenses

fast copy

emc software

trademarks of emc corporation