datasheet dupva-1-60 variable-gain ultra-wideband voltage ... · power supply output power supply...
TRANSCRIPT
Datasheet DUPVA-1-60
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
DE-DUPVA-1-60_R16/MvB,LK,JM/17JAN2017 Page 1 of 7
Features Variable gain 20 to 60 dB (x10 to x1000), switchable in 10 dB steps
Bandwidth 1 kHz … 1.2 GHz
Bandwidth, frequency response and pulse response independent of gain setting
Local and remote control
DC monitor output
Applications Oscilloscope and transient-recorder preamplifier
Photomultiplier and microchannel-plate amplifier
Signal-booster for optical receivers and current amplifiers
Time-resolved pulse and transient measurements
Automated measurement systems
Block Diagram
POWER SUPPLYOUTPUT
POWERSUPPLY
Monitor Buffer
Buffer-AmplifierProgrammableGain Stage
ProgrammableGain Stage
ProgrammableGain Stage
ProgrammableGain Stage
DC MONITOROUTPUT
SupplyVoltageRegulator
IN ( 15 V)±
OUT ( 12 V, +5 V)±
BS-DUPVA-1-60_R1
DIG. CONTROLINPUTS
Gain Control Unit
ManualSwitch
OptocouplerIsolated Unit
10 dB20 dB
0 dB10 dB
0 dB10 dB
0 dB10 dB
INPUT OUTPUT10 dB
Datasheet DUPVA-1-60
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 2
Specifications Test conditions VS = ±15 V, T
A = 25 °C, system impedance = 50 Ω
Gain Gain values 20, 30, 40, 50, 60 dB Gain accuracy ±0.1 dB (between settings)
±1 dB (overall) Gain flatness ±0.15 dB
Frequency Response Lower cut-off frequency 1kHz Upper cut-off frequency 1.2 GHz
Upper cut-off frequency rolloff 40 dB/Oct.
Time Response Rise/fall time (10 % - 90 %) 380 ps
Group delay 2.2 ns
Input Input impedance AC 50 Ω
Input impedance DC 100 kΩ
Input VSWR (@ 20 dB gain) 1.12 : 1 (f < 1 GHz)
1.7 : 1 (f < 2 GHz) Input VSWR (@ 30 - 60 dB gain) 1.2 : 1 (f < 1 GHz)
1.75 : 1 (f < 2 GHz)
50 Ω noise figure 3.0 dB (@ 60 dB gain)
3.5 dB (@ 30 - 50 dB gain)
Equivalent input voltage noise 450 pV/√Hz (@ 60 dB gain)
500 pV/√Hz (@ 30 - 50 dB gain)
1/f-noise corner 40 kHz
Output Output impedance 50 Ω
Output power P1dB
13 dBm (@ 100 MHz)
10 dBm (@ 500 MHz)
Output peak-peak voltage for linear Amplification 2 V (@ 100 MHz)
1.7 V (@ 500 MHz) Output VSWR 1.77 : 1 (f < 1 GHz)
2.0 : 1 (f < 2 GHz)
Third order intercept point IP3 21 dBm
Reverse isolation 80 dB
Dynamic range (without average) 70 dB (P1dB – min. detectable signal)
Monitor Output Monitor output gain 1 (@ ≥100 kΩ load)
Monitor output impedance 50 Ω (designed for ≥100 kΩ load)
Monitor output voltage range ±10 V Monitor output current ±25 mA
Monitor output bandwidth DC ... 100 kHz
Digital Control Control input voltage range Low: –0.8 ... +0.8 V
High: +1.8 ... +12 V
Power Supply Supply voltage ±15 V
Supply current +350 / –100 mA
(without current consumption from Sub-D-connector) Stabilized power supply output ±12 V / max. 50 mA, +5 V / max. 50 mA
(Auxiliary voltage outputs Pin 1-4 Sub-D-connector)
Case Weight 510 g (1.1 lb) Material AlMg4.5Mn, nickel-plated
Datasheet DUPVA-1-60
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 3
Specifications (continued)
Temperature Range
Storage temperature –40 ... +100 °C
Operating temperature 0 ... +60 °C
Absolute Maximum Ratings Signal input power +13 dBm (f > 500 Hz)
Signal input DC voltage ±16 V (slope max. ±1 V/ms)
Signal output reverse power +13 dBm
Signal output reverse DC voltage +16 V / ---12 V (slope max. ±1 V/ms)
Control input voltage +16 V / –5 V Power supply voltage ±17 V
Connectors Input SMA female
Output SMA female
Power supply Lemo® series 1S, 3-pin fixed socket
(mating plug type: FFA.1S.303.CLAC52)
Pin 1: +15 V
Pin 2: –15 V
Pin 3: GND
PIN 2
-Vs
PIN 3
GND
PIN 1
+Vs
Control port Sub-D 25-pin, female, qual. class 2 Pin 1: +12 V (stabilized power supply output)
Pin 2: –12 V (stabilized power supply output) Pin 3: AGND (analog ground)
Pin 4: +5 V (stabilized power supply output) Pin 5: Monitor output
Pin 6 - 8: NC Pin 9: DGND (ground f. digital control pin 10 - 25)
Pin 10 - 13: NC Pin 14: Digital control input: gain, LSB
Pin 15: Digital control input: gain Pin 16: Digital control input: gain, MSB
Pin 17 - 25: NC
Remote Control Operation General Remote control input bits are opto-isolated and connected
by logical OR to local switch setting. For remote control of the gain setting, set the local switch to “Ext.” and
select the wanted gain setting via a 3-bit-code at the corresponding digital inputs:
Gain setting - Gain Pin 14 Pin 15 Pin 16
corresponding inputs
20 dB Low Low Low
30 dB High Low Low 40 dB Low High Low
50 dB High High Low 60 dB Low Low High
Datasheet DUPVA-1-60
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 4
Typical Performance Characteristics
Frequency Frequency Frequency Frequency rrrresponse (esponse (esponse (esponse (llllogarithmic)ogarithmic)ogarithmic)ogarithmic)
Frequency Frequency Frequency Frequency rrrresponse (esponse (esponse (esponse (llll inear)inear)inear)inear)
Datasheet DUPVA-1-60
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 5
Typical Performance Characteristics
Input Input Input Input rrrreflection, S11eflection, S11eflection, S11eflection, S11
S ta r t: 9 kH zS top : 2 G H z 2 G H z
M arke r :
D G 22-0640-13
0 0 .2 0 .5
0 .5
-0 .5
1
-1
1
2 5
5
1 0
2
-2
-5
Input Input Input Input rrrreturn eturn eturn eturn lllloss, S11 (oss, S11 (oss, S11 (oss, S11 (llll inear inear inear inear mmmmagnitude)agnitude)agnitude)agnitude)
Datasheet DUPVA-1-60
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 6
Typical Performance Characteristics
Output Output Output Output rrrreflection, S22eflection, S22eflection, S22eflection, S22
S ta r t: 9 kH zS to p : 2 G H z 2 G H z
M a rke r :
D G 32-0640-13
0 0 .2 0 .5
0 .5
-0 .5
1
-1
1
2 5
5
1 0
2
-2
-5
Output Output Output Output rrrreturn eturn eturn eturn lllloss, S22 (oss, S22 (oss, S22 (oss, S22 (llll inear inear inear inear mmmmagnitude)agnitude)agnitude)agnitude)
Group Group Group Group ddddelayelayelayelay
Datasheet DUPVA-1-60
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 7
Dimensions
Accessories BNC-adapter set Model no.: ADAP-SMA-BNC-1
- Set of 2 SMA to BNC adapters
IN OUT
POWER
DZ01-0640-14
157 mm
150 mm
Ø 3.2 mm
44
mm
27
.3 m
m42
mm
14
.3 m
m
51
mm
137 mm
15
mm
79 mm
20
mm
10
5 m
m
FEMTO Messtechnik GmbH Klosterstr. 64 10179 Berlin · Germany Phone: +49 30 280 4711-0 Fax: +49 30 280 4711-11 Email: [email protected] www.femto.de
Specifications are subject to change without notice. Information provided herein is believed to be accurate and reliable. However, no responsibility is assumed by FEMTO Messtechnik GmbH for its use, nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of FEMTO Messtechnik GmbH. Product names mentioned may also be trademarks used here for identification purposes only.
© by FEMTO Messtechnik GmbH · Printed in Germany
Datasheet DUPVA-1-70
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
DE-DUPVA-1-70_R16/MvB,LK,JM/17JAN2017 Page 1 of 7
Features Variable gain 30 to 70 dB (approx. x30 to x3000), switchable in 10 dB steps
Bandwidth 1 kHz … 1.1 GHz
Bandwidth, frequency response and pulse response independent of gain setting
Local and remote control
DC monitor output
Applications Oscilloscope and transient-recorder preamplifier
Photomultiplier and microchannel-plate amplifier
Signal-booster for optical receivers and current amplifiers
Time-resolved pulse and transient measurements
Automated measurement systems
Block Diagram
POWER SUPPLYOUTPUT
POWERSUPPLY
Monitor Buffer
Buffer-AmplifierProgrammableGain Stage
ProgrammableGain Stage
ProgrammableGain Stage
ProgrammableGain Stage
DC MONITOROUTPUT
SupplyVoltageRegulator
IN ( 15 V)±
OUT ( 12 V, +5 V)±
BS-DUPVA-1-70_R1
DIGITALCONTROL INPUTS
Gain Control Unit
ManualSwitch
OptocouplerIsolated Unit
20 dB30 dB
0 dB10 dB
0 dB10 dB
0 dB10 dBINPUT OUTPUT10 dB
Datasheet DUPVA-1-70
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 2
Specifications Test conditions VS = ±15 V, T
A = 25 °C, system impedance = 50 Ω
Gain Gain values 30, 40, 50, 60, 70 dB Gain accuracy ±0.1 dB (between settings)
±1 dB (overall) Gain flatness ±0.15 dB
Frequency Response Lower cut-off frequency 1 kHz Upper cut-off frequency 1.1 GHz
Upper cut-off frequency rolloff 40 dB/oct.
Time Response Rise/fall time (10 % - 90 %) 390 ps
Group delay 2.2 ns
Input Input impedance AC 50 Ω Input impedance DC 100 kΩ
Input VSWR (@ 30 dB gain) 1.1 : 1 (f < 1 GHz)
1.2 : 1 (f < 2 GHz) Input VSWR (@ 40 - 70 dB gain) 1.7 : 1 (f < 1 GHz)
1.7 : 1 (f < 2 GHz)
50 Ω noise figure 1.9 dB (@ 70 dB gain)
2.5 dB (@ 40 - 60 dB gain)
Equivalent input voltage noise 330 pV/√Hz (@ 70 dB gain)
400 pV/√Hz (@ 40 - 60 dB gain)
1/f-noise corner 20 kHz
Output Output impedance 50 Ω
Output power P1dB
12 dBm (@ 100 MHz) 11 dBm (@ 500 MHz)
Output peak-to-peak voltage for linear amplification 2 V (@ 100 MHz)
1.7 V (@ 500 MHz) Output VSWR 1.5 : 1 (f < 1 GHz)
1.7 : 1 (f < 2 GHz) Third order intercept point IP
3 20 dBm
Reverse isolation 80 dB Dynamic range (without average) 62 dB (P
1dB – min. detectable signal)
Monitor Output Monitor output gain 1 (@ ≥100 kΩ load)
Monitor output impedance 50 Ω (designed for ≥100 kΩ load)
Monitor output voltage range ±10 V
Monitor output current ±25 mA Monitor output bandwidth DC ... 100 kHz
Digital Control Control input voltage range Low: –0.8 ... +0.8 V High: +1.8 ... +12 V
Power Supply Supply voltage ±15 V
Supply current +250 / –100 mA
(without current consumption from Sub-D-connector) Stabilized power supply output ±12 V / max. 50 mA, +5 V / max. 50 mA
(Auxiliary voltage outputs Pin 1-4 Sub-D-connector)
Case Weight 510 g (1.1 lb)
Material AlMg4.5Mn, nickel-plated
Datasheet DUPVA-1-70
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 3
Specifications (continued)
Temperature Range
Storage temperature –40 ... +100 °C
Operating temperature 0 ... +60 °C
Absolute Maximum Ratings Signal input power +13 dBm (f > 500 Hz)
Signal input DC voltage ±16 V (slope max. ±1 V/ms)
Signal output reverse power +13 dBm
Signal output reverse DC voltage +16 V / –12 V (slope max. ±1 V/ms)
Control input voltage +16 V / –5 V Power supply voltage ±17 V
Connectors Input SMA female
Output SMA female
Power supply Lemo® series 1S, 3-pin fixed socket
(mating plug type: FFA.1S.303.CLAC52)
Pin 1: +15V
Pin 2: –15V
Pin 3: GND
PIN 2
-Vs
PIN 3
GND
PIN 1
+Vs
Control port Sub-D 25-pin, female, qual. class 2
Pin 1: +12V (stabilized power supply output) Pin 2: –12V (stabilized power supply output)
Pin 3: AGND (analog ground) Pin 4: +5V (stabilized power supply output)
Pin 5: Monitor output Pin 6 - 8: NC
Pin 9: DGND (ground f. digital control pin 10 - 25) Pin 10 - 13: NC
Pin 14: Digital control input: gain, LSB Pin 15: Digital control input: gain
Pin 16: Digital control input: gain, MSB
Pin 17 - 25: NC
Remote Control Operation General Remote control input bits are opto-isolated and connected by logical OR to local switch setting. For remote control
of the gain setting, set the local switch to “Ext.” and select the wanted gain setting via a 3-bit-code at the
corresponding digital inputs:
Gain setting - Gain Pin 14 Pin 15 Pin 16
corresponding inputs
30 dB Low Low Low 40 dB High Low Low
50 dB Low High Low 60 dB High High Low
70 dB Low Low High
Datasheet DUPVA-1-70
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 4
Typical Performance Characteristics
Frequency Frequency Frequency Frequency rrrresponse (esponse (esponse (esponse (llllogarithmic)ogarithmic)ogarithmic)ogarithmic)
Frequency Frequency Frequency Frequency rrrresponse (esponse (esponse (esponse (llll inear)inear)inear)inear)
Datasheet DUPVA-1-70
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 5
Typical Performance Characteristics
Input Input Input Input rrrreflection, S11eflection, S11eflection, S11eflection, S11
Input Input Input Input rrrreturn eturn eturn eturn lllloss, S11 (Linear Magnitude)oss, S11 (Linear Magnitude)oss, S11 (Linear Magnitude)oss, S11 (Linear Magnitude)
Datasheet DUPVA-1-70
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 6
Typical Performance Characteristics
Output Output Output Output rrrreflection, S22eflection, S22eflection, S22eflection, S22
Output Output Output Output rrrreturn eturn eturn eturn rrrross, S22 (Linear Magnitude)oss, S22 (Linear Magnitude)oss, S22 (Linear Magnitude)oss, S22 (Linear Magnitude)
Group Group Group Group ddddelayelayelayelay
Datasheet DUPVA-1-70
Variable-Gain
Ultra-Wideband Voltage Amplifier
S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y
Page 7
Dimensions
Accessories BNC adapter set Model no.: ADAP-SMA-BNC-1
- set of 2 SMA to BNC adapters
IN OUT
POWER
DZ01-0640-14
157 mm
150 mm
Ø 3.2 mm
44
mm
27
.3 m
m42
mm
14
.3 m
m
51
mm
137 mm
15
mm
79 mm
20
mm
10
5 m
m
FEMTO Messtechnik GmbH Klosterstr. 64 10179 Berlin · Germany Phone: +49 30 280 4711-0 Fax: +49 30 280 4711-11 Email: [email protected] www.femto.de
Specifications are subject to change without notice. Information provided herein is believed to be accurate and reliable. However, no responsibility is assumed by FEMTO Messtechnik GmbH for its use, nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of FEMTO Messtechnik GmbH. Product names mentioned may also be trademarks used here for identification purposes only.
© by FEMTO Messtechnik GmbH · Printed in Germany