dball-dball2-hyundai2-rsr en ig nf20170505 · 2017-05-08 · ® hyundai and kia are registered...
TRANSCRIPT
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
® Hyundai and Kia are registered trademarks and property of their respective companies.
Important!This product is NOT compatible with vehicles equipped with a manual transmission.
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
SmartStart CompatibleSmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information.
Installation Guide
Vehicle Application Guide...................................................................................................................................................
Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)Type 1.................................................................................................................................................................................Type 2.................................................................................................................................................................................Type 3.................................................................................................................................................................................Type 4.................................................................................................................................................................................Type 5.................................................................................................................................................................................Type 6.................................................................................................................................................................................Type 7.................................................................................................................................................................................Type 8.................................................................................................................................................................................Type 9.................................................................................................................................................................................Type 10...............................................................................................................................................................................SmartStart/XL202 Installation Notes..................................................................................................................................
ProgrammingModule Programming.........................................................................................................................................................Module Reset.....................................................................................................................................................................Hard Reset.........................................................................................................................................................................Feature & Option List..........................................................................................................................................................Feature Programming.........................................................................................................................................................
LED Diagnostics & Troubleshooting...................................................................................................................................Parking Light Error Codes..................................................................................................................................................
Limited One-Year Consumer Warranty...............................................................................................................................
Quick Reference Guide.....................................................................................................................................................
02
0305070911131517192123
2425262727
2830
31
32
Index
This installation is compatible with firmware 4.05 and up.
The HYUNDAI2 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Hyundai and Kia vehicles. This guide supports the installation of a DBALL2 in Remote Start Ready (RSR) mode. This solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF System or SmartStart (all sold separately).
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to the Module Programming section on page 24 for more information.
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Vehicle Application GuidePage 2
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.
Vehicles
2017
2016
2015
2014
2013
2012
2011
PK
-Im
mobilizer
Bypass-D
ata
No
Key
Req'd
AV
-Panic
Mode
Activ
atio
n
DL-A
rmF
acto
ryS
ecurity
DL-D
isarm
Facto
ryS
ecurity
DL-D
oor
Lock
Contr
ol
DL-D
oor
Unlo
ck
DL-D
river
Priority
Unlo
ck
DL-T
runk
/H
atc
hR
ele
ase
RS
-3x
LO
CK
ST
AR
T(S
tart
contr
olu
sin
gO
EM
Rem
ote
)
RS
-3x
LO
CK
ST
OP
(Sto
pcontr
olu
sin
gO
EM
Rem
ote
)
RS
-Rem
ote
Sta
rtR
eady
RS
-Sm
art
Sta
rt
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onito
ring
ALL
Door
Pin
s
SS
-Entr
yM
onito
ring
Hood
Pin
SS
-Entr
yM
onito
ring
Tru
nk/H
atc
hP
in
SS
-Facto
ryA
larm
Trigger
Monito
ring
ST
-Bra
ke
Sta
tus
(footbra
ke)
Hyundai
Elantra (Smart Key) 2 2 2 1 1 1 • • • • • • • • • • • • • • • • • •
Elantra Coupe (Smart Key) 1 1 • • • • • • • • • • • • • • • • • •
Elantra GT (Smart Key) 2 2 2 2 2 • • • • • • • • • • • • • • • • • •
Veloster (Smart Key) 3 3 3 3 3 • • • • • • • • • • • • • • • • • •
Kia 17 16 15 14 13 12 11
Optima (Smart Key) 5 5 4 4 4 • • • • • • • • • • • • • • • • • •
Optima Hybrid (Smart Key) 5 5 5 4 4 4 • • • • • • • • • • • • • • • • • •
Rio (Smart Key) 10 10 10 10 10 10 • • • • • • • • • • • • • • • • • •
Rondo (Smart Key) 6 6 6 • • • • • • • • • • • • • • • • • •
Sorento (Smart Key) 7 7 • • • • • • • • • • • • • • • • • •
Sportage (Smart Key) 9 9 9 8 8 8 • • • • • • • • • • • • • • • • • •
Legend:
PK: Transponder & Immobilizer Override
AV: Horn & Lights Controls
DL: OE Door Lock & Alarm Controls
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
HS CAN Low: Tan: 4
(-) PTS Output 1: Green/Black: 2
FT CAN High: Orange/Green: 5
(-) Parking Lights Output: Red/Black: 4
FT CAN Low: Orange/Brown: 6
(+) Ignition 1 Output: Gray: 6
(+) Ignition 2: Yellow: 8
(+) 12V: Brown: 7
(+) Starter Output: Gray/Black: 7
EMS COM Data: Orange/Black: 11
HS CAN High: Tan/Black: 3
(-) PTS Output 2: Black/White: 1
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
6: White/Black: (-) Hood
Note: hood pin only required on vehicles not equipped with a factory hood pin
(+) 12V: Red: 13
(-) Ground: Black: 14
B-CAN High: White/Orange or Brown, pin 13
B-CAN Low: Yellow/Orange or White, pin 1
(-) PTS 1:Yellow/Black, pin 1
Black Conn. M04(at Push-to-Start button)
C-CAN High: White, Pin 6
C-CAN Low: Yellow, Pin 14
1 8
169
OBDIIDiagnostic connector
12
11
22
23
21
20
19
17
16
15
14
131
117
2
19
420
21
6
23
824
9
11
1228
27
13
27
28
31
32
29
36
38
15
18
19
20
34
22
24
25
2
4
7
8
10
11
12
14 1
39 26 13
15
16
31
*
32
*
*
*
*
*
*
*
*
**
*
*
*
*
*
***
**
*
*
*
*
*********
I/P-H (MAIN)I/P-F (MAIN)
I/P-G (MAIN)
23
24
1112
22
10
219
208
197
186
175
164
153
142
131
1 2
87
3
9
4
10
5
11
6
12
(-) Parking Lights:Pink or Orange, pin 2
White conn. M01-L(at Headlight Switch)
1 2 63 74 85 9 10 11 12 13
White conn. I/P-G(Back of I/P Junction Box)
EMS COM Data: Brown/Orange, pin 10
White conn. EM11(Driver Kick Panel)
41
11
26
51
40
50
10
25
1 31
38
39
2 32
3 33
8 23
9
17
18
43
194
205 45
216 46
227 47
27
12
52
28
13
53
29
14
54
30
15
55
34
35
36
37
24
42
48
49
16
44
(+) Starter:Yellow, pin 39
(+) Ignition 1:Pink, pin 27
15
16
17
18
19
20
21
22
23
24
25
28
29
30
31
32
33
34
35
36
37
38
12
23
45
67
89
10
111
13
14
26
27
39
Black conn. I/P-F(Back of I/PJunction Box)
30
86 8587
87a
(+) 12V
Fuse 30A
30
86 8587
87a
(+) 12V
Fuse 30A
Rear of I/P Junction Box (located left side of dash panel)
Installation Type 1Page 3
10
RF
Prog. Button
LED
4
12
14
2
10
DBALL/DBALL2
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Fuses
I/P Junction Box(Left Side of Dash Panel)
(+) 12V:Red, pin 2
Black Conn. I/P-D(front of I/P Junction Box)
2 31
The Remote Start Safety Override Switch MUST be in the OFF position.
(+) Ignition 2:Orange, pin 1
(-) PTS 2:Yellow/Orange, pin 8
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 1 - Vehicle Wiring Reference ChartPage 4
Function Color Pin Polarity Location Color Pins
12V Red 2 (+) I/P-D, front of drivers I/P junction box. Black 3
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/Orange 8 (-) M04, Push-to-Start Button. Black 12
Parking Lights Pink or Orange 2 (-) M01-L, headlight switch. White 13
C-CAN High White 6 Data ODBII. Black 16
C-CAN Low Yellow 14 Data ODBII. Black 16
B-CAN High White/Orange or Brown 13 Data I/P-G, back of drivers I/P junction box. White 24
B-CAN Low Yellow/Orange or White 1 Data I/P-G, back of drivers I/P junction box. White 24
Ignition 1 Pink 27 (+) I/P-F, back of drivers I/P junction box. Black 39
Ignition 2 Orange 1 (+) I/P-F, back of drivers I/P junction box. Black 39
Starter Yellow 39 (+) I/P-F, back of drivers I/P junction box. Black 39
EMS COM Brown/Orange 10 Data EM11, drivers kick panel. White 55
12V Red 2 (+) I/P-D, front of drivers I/P junction box. Black 3
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/Orange 8 (-) M04, Push-to-Start Button. Black 12
Parking Lights Pink 2 (-) M01-L, headlight switch. White 13
C-CAN High White 6 Data ODBII. Black 16
C-CAN Low Yellow 14 Data ODBII. Black 16
B-CAN High White/Orange or Brown 13 Data I/P-G, back of drivers I/P junction box. White 24
B-CAN Low Yellow/Orange or White 1 Data I/P-G, back of drivers I/P junction box. White 24
Ignition 1 Pink 27 (+) I/P-F, back of drivers I/P junction box. Black 39
Ignition 2 Orange 1 (+) I/P-F, back of drivers I/P junction box. Black 39
Starter Yellow 39 (+) I/P-F, back of drivers I/P junction box. Black 39
EMS COM Brown/Orange 10 Data EM11, drivers kick panel. White 55
Wire Information Connector Information
Hyundai Elantra (Smart Key) 2011-2013
Elantra Coupe (Smart Key) 2013-2014
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
B-CAN High: Green, pin 13
B-CAN Low: Orange,pin 1 HS CAN Low: Tan: 4
(-) PTS Output 1: Green/Black: 2
FT CAN High: Orange/Green: 5
(-) Parking Lights Output: Red/Black: 4
FT CAN Low: Orange/Brown: 6
(+) Ignition 1 Output: Gray: 6
(+) Ignition 2 Output: Yellow: 8
(+) 12V: Brown: 7
(+) Starter Output: Gray/Black: 7
EMS COM Data: Orange/Black: 11
HS CAN High: Tan/Black: 3
(-) PTS Output 2: Black/White: 1
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
(+) 12V: Red: 13
(-) Ground: Black: 14
(+) Starter: Yellow, pin 39
(+) Ignition 1:Pink or White,
pin 27
C-CAN High: White, Pin 6
C-CAN Low: Yellow, Pin 14
1 8
169
OBDIIDiagnostic connector
12
11
22
23
21
20
19
17
16
15
14
131
117
2
19
420
21
6
23
824
9
11
1228
27
13
27
28
31
32
29
36
38
15
18
19
20
34
22
24
25
2
4
7
8
10
11
12
14 1
39 26 13
15
16
31
*
32
*
*
*
*
*
*
*
*
**
*
*
*
*
*
***
**
*
*
*
*
*********
I/P-H (MAIN)I/P-F (MAIN)
I/P-G (MAIN)
23
24
1112
22
10
219
208
197
186
175
164
153
142
131
(-) Parking Lights: Pink, pin 2
White Conn. M01-L(at Headlight Switch)
1 2 63 74 85 9 10 11 12 13
15
16
17
18
19
20
21
22
23
24
25
28
29
30
31
32
33
34
35
36
37
38
12
23
45
67
89
10
111
13
14
26
27
39
White conn. I/P-G(Back of I/P Junction Box)
Black conn. I/P-F(Back of I/P Junction Box)
EMS COM Data: Brown/Orange, pin 12
39
172
50
49
40
29
28
183
7 22
14
54
44
36
6 21
13
53
43
35
42
34
12
4
205
19
52
11
51
41
33
45
37
1 16
27
38
48
26
32
58
56
57
31
30
47
46
25
24
10
9
238 15
55
White Conn. EM11(Driver Kick Panel) 30
86 8587
87a
(+) 12VFuse 30A
Rear of I/P Junction Box (located left side of dash panel)
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Fuses
I/P Junction Box(Left Side of Dash Panel)
(+) 12V:Red, pin 2
Black Conn. I/P-D(front of I/P Junction Box)
2 31
Hood Pin
Remote Start Safety Override Switch
6: White/Black: (-) Hood
Note: hood pin only required on vehicles not equipped with a factory hood pin
The Remote Start Safety Override Switch MUST be in the OFF position.
(+) Ignition 2: Orange, pin 130
86 8587
87a
(+) 12VFuse 30A
(-) PTS 1:Yellow/Black, pin 1
Black Conn. M04(at Push-to-Start button)
1 2
87
3
9
4
10
5
11
6
12
(-) PTS 2:Yellow/Orange, pin 8
Installation Type 2Page 5
Installation Type 2Page 5
10
RF
Prog. Button
LED
4
12
14
2
10
DBALL/DBALL2
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 2 - Vehicle Wiring Reference ChartPage 6
Function Color Pin Polarity Location Color Pins
12V Red 2 (+) I/P-D, front of drivers I/P junction box. Black 3
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/Orange 8 (-) M04, Push-to-Start Button. Black 12
Parking Lights Pink 2 (-) M01-L, headlight switch. White 13
C-CAN High White 6 Data ODBII. Black 16
C-CAN Low Yellow 14 Data ODBII. Black 16
B-CAN High Green 13 Data I/P-G, back of drivers I/P junction box. White 24
B-CAN Low Orange 1 Data I/P-G, back of drivers I/P junction box. White 24
Ignition 1 Pink or White 27 (+) I/P-F, back of drivers I/P junction box. Black 39
Ignition 2 Orange 4 (+) I/P-F, back of drivers I/P junction box. Black 39
Starter Yellow 39 or 40 (+) I/P-F, back of drivers I/P junction box or EM11, driver kick panel Black or White 39 or 58
EMS COM Blue/Black or Brown/Orange 12 Data EM11, drivers kick panel. White 58
12V Red 2 (+) I/P-D, front of drivers I/P junction box. Black 3
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/Orange 8 (-) M04, Push-to-Start Button. Black 12
Parking Lights Pink 2 (-) M01-L, headlight switch. White 13
C-CAN High White 6 Data ODBII. Black 16
C-CAN Low Yellow 14 Data ODBII. Black 16
B-CAN High Green 13 Data I/P-G, back of drivers I/P junction box. White 24
B-CAN Low Orange 1 Data I/P-G, back of drivers I/P junction box. White 24
Ignition 1 Pink or White 27 (+) I/P-F, back of drivers I/P junction box. Black 39
Ignition 2 Orange 4 (+) I/P-F, back of drivers I/P junction box. Black 39
Starter Yellow 39 or 40 (+) I/P-F, back of drivers I/P junction box or EM11, driver kick panel Black or White 39 or 58
EMS COM Blue/Black or Brown/Orange 12 Data EM11, drivers kick panel. White 58
Wire Information Connector Information
Hyundai Elantra (Smart Key) 2014-2016
Hyundai Elantra GT (Smart Key) 2013-2017
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
(-) PTS Output 1: Green/Black: 2
(-) Parking Lights: Red/Black: 4
(+) Ignition 1 Output: Gray: 6
(+) Starter Output: Gray/Black: 7
EMS COM Data: Orange/Black: 11
(-) Autolights Off Output: Blue/Red: 12
(-) PTS Output 2: Black/White: 1
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
6: White/Black: (-) Hood
Note: hood pin only required on vehicles not equipped with a factory hood pin
C-CAN High: Red or White, pin 6
C-CAN Low: Blue or Yellow, pin 14
1 8
169
OBDIIDiagnostic connector
(-) Parking Lights: Pink, pin 11
B-CAN High: Red or
White/Orange,pin 5
B-CAN Low:Blue orYellow/Orange,pin 6
White Connector I/P-C(Rear of I/P Junction Box)
24
12
23
1122
10
21
9
20
8
19
7
18
617
516
4
15
3
14
2
13
1
(+) Ignition 1: Pink, pin 7
(+) Starter: Yellow, pin 5
White conn. I/P-F(front of I/P Junction Box)
43 10
13 16
2 9
12 15
1 8
11 145 6 7
(-) PTS 1: Yellow/Black, pin 1
White conn. M04(at Push-to-Start button)
1 3 52 4 6
7 9 118 10 12
White conn. MF11(Driver Kick Panel)
(-) Driver Door Trigger:Brown, pin 7
For Veloster2012-2013
& early 2014
For Velosterlate 2014-2016OR
EMS COM EMS COM
White conn. EM11(Driver Kick Panel)
Black conn. EM11(Driver Kick Panel)
EMS COM Data: Blue, pin 10
41
11 51
40
10
25
1 31
38
39
28
9
17
18
19
20
21
22
27
28
29
30
34
35
36
37
24
42
48
49
16
44
HS CAN Low: Tan: 4
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) Ignition 2 Output: Yellow: 8
HS CAN High: Tan/Black: 3
(+) 12V: Red: 13
(-) Ground: Black: 14
(+) 12V: Brown: 7
I/P-K
I/P-G
I/P-H
Fu
ses
I/P-L
I/P-E I/P-F
I/P-M
I/P-N
Fuse Panel (front)
I/P Junction Box(left side of Dash Panel)
30
86 8587
87a
(+) 12VFuse 30A
Installation Type 3Page 7
10
RF
Prog. Button
LED
4
12
14
2
10
DBALL/DBALL2
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
1 2 3 4
(+) 12V:Red, pin 2
Black Conn. I/P-L(front of I/P Junction Box)
The Remote Start Safety Override Switch MUST be in the OFF position.
(+) Ignition 2: Red, pin 4
30
86 8587
87a
(+) 12VFuse 30A
(-) PTS 2: Yellow/Orange, pin 8
1 29
48
10
37
19
27
28
55
2 20
34
57
89
6
13
12
16
15
14
17
18
21
39
48
22 32
31
40
49
23
33
41
50
24
34
43
52
42
51
25
35
44
53
26
36
45
54
30
11 38
47
56
EMS COM Data: Blue, pin 16
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 3 - Vehicle Wiring Reference ChartPage 8
Function Color P in Pola rity Loca tion Color P ins
12V Red 2 (+) I/P-L, front of drivers I/P junc tion box. W hite 4
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/O range 8 (-) M04, Push-to-Start Button. Black 12
C-CAN High W hite 6 Data O DBII. Black 16
C-CAN Low Yellow 14 Data O DBII. Black 16
Ignition 1 Pink 7 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
Ignition 2 Red 4 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
Starter Yellow 5 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
B-CAN High W hite/O range 5 Data I/P-C, back of drivers I/P junc tion box. W hite 24
B-CAN Low Yellow/O range 6 Data I/P-C, back of drivers I/P junc tion box. W hite 24
Parking Lights Pink 11 (-) I/P-C, back of drivers I/P junc tion box. W hite 24
EMS CO M Blue 10 Data EM11, drivers kick panel. W hite 55
Drivers Door Trigger Brown 7 (-) MF11, drivers kick panel. W hite 56
12V Red 2 (+) I/P-L, front of drivers I/P junc tion box. W hite 4
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/O range 8 (-) M04, Push-to-Start Button. Black 12
C-CAN High W hite 6 Data O DBII. Black 16
C-CAN Low Yellow 14 Data O DBII. Black 16
Ignition 1 Pink 7 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
Ignition 2 Red 4 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
Starter Yellow 5 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
B-CAN High W hite/O range 5 Data I/P-C, back of drivers I/P junc tion box. W hite 24
B-CAN Low Yellow/O range 6 Data I/P-C, back of drivers I/P junc tion box. W hite 24
Parking Lights Pink 11 (-) I/P-C, back of drivers I/P junc tion box. W hite 24
EMS CO M Blue 16 Data EM11, drivers kick panel. W hite 55
Drivers Door Trigger Brown 7 (-) MF11, drivers kick panel. W hite 56
12V Red 2 (+) I/P-L, front of drivers I/P junc tion box. W hite 4
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/O range 8 (-) M04, Push-to-Start Button. Black 12
C-CAN High W hite 6 Data O DBII. Black 16
C-CAN Low Yellow 14 Data O DBII. Black 16
Ignition 1 Pink 7 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
Ignition 2 Red 4 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
Starter Yellow 5 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
B-CAN High W hite/O range 5 Data I/P-C, back of drivers I/P junc tion box. W hite 24
B-CAN Low Yellow/O range 6 Data I/P-C, back of drivers I/P junc tion box. W hite 24
Parking Lights Pink 11 (-) I/P-C, back of drivers I/P junc tion box. W hite 24
Drivers Door Trigger Brown 7 (-) MF11, drivers kick panel. W hite 56
EMS CO M Blue 16 Data EM11, drivers kick panel. Black 60
12V Red 1 (+) I/P-C, front of drivers I/P junc tion box. Black 4
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/O range 8 (-) M04, Push-to-Start Button. Black 12
C-CAN High Red 6 Data O DBII. Black 16
C-CAN Low Blue 14 Data O DBII. Black 16
Ignition 1 Pink 7 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
Ignition 2 Red 4 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
Starter Yellow 5 (+) I/P-F, front of drivers I/P junc tion box. W hite 16
B-CAN High Red 5 Data I/P-C, back of drivers I/P junc tion box. W hite 24
B-CAN Low Blue 6 Data I/P-C, back of drivers I/P junc tion box. W hite 24
Parking Lights Pink 11 (-) I/P-C, back of drivers I/P junc tion box. W hite 24
Drivers Door Trigger Brown 7 (-) MF11, drivers kick panel. W hite 56
EMS CO M Blue 16 Data EM11, drivers kick panel. Black 60
Hyundai Ve loste r (Smart Key) 2016
W ire Inform a tion Conne ctor Inform a tion
Hyundai Ve loste r (Smart Key) 2012-2013
Hyundai Ve loste r (Smart Key) 2014 (Early)
Hyundai Ve loste r (Smart Key) 2014 (Late ) - 2015
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Hood Pin
Remote Start Safety Override Switch
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
6: White/Black: (-) Hood
Note: hood pin only required on vehicles not equipped with a factory hood pin
(-) PTS Output 1: Green/Black: 2
(-) Parking Lights Output: Red/Black: 4
(+) Ignition 1 Output: Gray: 6
(+) Starter Output: Gray/Black: 7
EMS COM Data: Orange/Black: 11
(-) PTS Output 2: Black/White: 1
C-CAN High: White, pin 6
C-CAN Low: Yellow, pin 14
1 8
169
OBDIIDiagnostic connector
(-) Parking Lights: Pink, pin 1
White conn. M01-L(at Headlight Switch)
21 63 74 85 9 10 11 12 13
110
19
28
36
40
211
20
29
37
41
312
21
30
38
42
413
22
31
39
43
514
23
32
615
24
33
716
25
34
8918
27
17
26
35
White Conn. EM11(Driver Kick Panel)
EMS COM Data:Brown/Orange or Blue, pin 10
B-CAN Low:Yellow/Orange, pin 38
B-CAN High:White/Orange, pin 25
(+) Starter:Orangeor Yellow,pin 26
15
16
17
18
19
20
21
22
23
24
25
28
29
30
31
32
33
34
35
36
37
38
12
23
45
67
89
10
111
13
14
26
27
39
(+) Ignition 1:Pink, pin 1
Black conn. I/P-E(Back of I/P Junction Box,located left side of dash panel)
HS CAN Low: Tan: 4
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) Ignition 2 Output: Yellow: 8
HS CAN High: Tan/Black: 3
(+) 12V: Red: 13
(-) Ground: Black: 14
(+) 12V: Brown: 7
30
86 8587
87a
Fuse 30A
Installation Type 4Page 9
10
RF
Prog. Button
LED
4
12
14
2
10
DBALL/DBALL2
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Fuses
I/P Junction Box(Left Side of Dash Panel)
(+) 12V:Red or Pink, pin 1
Black Conn. I/P-C(front of I/P Junction Box)
2 31
The Remote Start Safety Override Switch MUST be in the OFF position.
(+) Ignition 2:
Orange, pin 14
30
86 8587
87a
(+) 12V
Fuse 30A
(-) PTS 1:Yellow/Black, pin 1
Black conn. M04(at Push-to-Start button)
1 2
87
3
9
4
10
5
11
6
12
(-) PTS 2:Yellow/Orange, pin 8
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 4 - Vehicle Wiring Reference ChartPage 10
Function Color Pin Polarity Location Color Pins
12V Pink 1 (+) I/P-C, front of drivers I/P junction box. Black 3
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/Orange 8 (-) M04, Push-to-Start Button. Black 12
Parking Lights Pink 1 (-) M01-L, headlight switch. White 13
C-CAN High White 6 Data ODBII. Black 16
C-CAN Low Yellow 14 Data ODBII. Black 16
B-CAN High White/Orange 25 Data I/P-E, back of drivers I/P junction box. Black 39
B-CAN Low Yellow/Orange 38 Data I/P-E, back of drivers I/P junction box. Black 39
Ignition 1 Pink 1 (+) I/P-E, back of drivers I/P junction box. Black 39
Ignition 2 Orange 14 (+) I/P-E, back of drivers I/P junction box. Black 39
Starter Orange or Yellow 26 (+) I/P-E, back of drivers I/P junction box. Black 39
EMS COM Brown/Yellow 10 Data EM11, drivers kick panel. White 43
12V Red 1 (+) I/P-C, front of drivers I/P junction box. Black 3
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/Orange 8 (-) M04, Push-to-Start Button. Black 12
Parking Lights Pink 1 (-) M01-L, headlight switch. White 13
C-CAN High White 6 Data ODBII. Black 16
C-CAN Low Yellow 14 Data ODBII. Black 16
B-CAN High White/Orange 25 Data I/P-E, back of drivers I/P junction box. Black 39
B-CAN Low Yellow/Orange 38 Data I/P-E, back of drivers I/P junction box. Black 39
Ignition 1 Pink 1 (+) I/P-E, back of drivers I/P junction box. Black 39
Ignition 2 Orange 14 (+) I/P-E, back of drivers I/P junction box. Black 39
Starter Yellow 26 (+) I/P-E, back of drivers I/P junction box. Black 39
EMS COM Blue 10 Data EM11, drivers kick panel. White 43
Wire Information Connector Information
Kia Optima (Smart Key) 2011-2013
Kia Optima Hybrid (Smart Key) 2011-2013
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
(-) PTS Output 1: Green/Black: 2
(-) Parking Lights Output: Red/Black: 4
(+) Starter Output: Gray/Black: 7
EMS COM Data: Orange/Black: 11
(+) Ignition 1 Output: Gray: 6
(-) PTS Output 2: Black/White: 1
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
White conn. I/P-G(Back of I/P Junction Box,
located left side of dash panel)
(-) Parking Lights: Pink, pin 1
White conn. M 01-L(at Headlight Switch)
21 63 74 85 9 10 11 12 13
B-CAN High: White/Orange, pin 13
B-CAN Low: Yellow/Orange, pin 1
1
13
2
14
3
15
4
16
5
17
6
18
7
19
8
20
9
21
10
22
11
23
12
24
C-CAN High: White, pin 6
C-CAN Low: Yellow, pin 14
1 8
169
OBDIIDiagnosticconnector
(+) Starter: Yellow or Gray, pin 9
(+) Ignition 2: Orange, pin 32
EMS COM Data: Brown/Orange or Blue, pin 41
White Conn. EM11(Driver Kick Panel)
HS CAN Low: Tan: 4
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) Ignition 2 Output: Yellow: 8
HS CAN High: Tan/Black: 3
(+) 12V: Red: 13
(-) Ground: Black: 14
(+) 12V: Brown: 7
30
86 8587
87a
Fuse30A
(+) 12V
30
86 8587
87a
Fuse30A
(+) 12V
Installation Type 5Page 11
10
RF
Prog. Button
LED
4
12
14
2
10
DBALL/DBALL2
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Fuses
I/P Junction Box(Left Side of Dash Panel)
(+) 12V:Red, pin 1
Black Conn. I/P-C(front of I/P Junction Box)
2 31
Hood Pin
Remote Start Safety Override Switch
6: White/Black: (-) Hood
Note: hood pin only required on vehicles not equipped with a factory hood pin
The Remote Start Safety Override Switch MUST be in the OFF position.
(-) PTS 1:Yellow/Black,
pin 1
Black conn. M04(at Push-to-Start button)
1 2
87
3
9
4
10
5
11
6
12
(-) PTS 2:Yellow/Orange, pin 8
(+) Ignition 1: Pink, pin 26
5
39
172
50
49
40
29
28
183
7 22
21
14
54
44
36
6 13
53
43
35
42
34
12
4
20
19
52
11
51
41
33
45
37
1 16
27
38
48
26
32
58
56
57
31
30
47
46
25
24
10
9
238 15
55
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 5 - Vehicle Wiring Reference ChartPage 12
Function Color Pin Polarity Location Color Pins
12V Red 1 (+) I/P-C, front of drivers I/P junction box. Black 3
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/Orange 8 (-) M04, Push-to-Start Button. Black 12
Parking Lights Pink 1 (-) M01-L, headlight switch. White 13
C-CAN High White 6 Data ODBII. Black 16
C-CAN Low Yellow 14 Data ODBII. Black 16
B-CAN High White/Orange 13 Data I/P-G, back of drivers I/P junction box. White 24
B-CAN Low Yellow/Orange 1 Data I/P-G, back of drivers I/P junction box. White 24
Ignition 1 Pink 26 (+) EM11, drivers kick panel. White 58
Ignition 2 Orange 32 (+) EM11, drivers kick panel. White 58
Starter Gray 9 (+) EM11, drivers kick panel. White 58
EMS COM Brown/Orange or Blue 41 Data EM11, drivers kick panel. White 58
12V Red 1 (+) I/P-C, front of drivers I/P junction box. Black 3
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/Orange 8 (-) M04, Push-to-Start Button. Black 12
Parking Lights Pink 1 (-) M01-L, headlight switch. White 13
C-CAN High White 6 Data ODBII. Black 16
C-CAN Low Yellow 14 Data ODBII. Black 16
B-CAN High White/Orange 13 Data I/P-G, back of drivers I/P junction box. White 24
B-CAN Low Yellow/Orange 1 Data I/P-G, back of drivers I/P junction box. White 24
Ignition 1 Pink 26 (+) EM11, drivers kick panel. White 58
Ignition 2 Black/Orange 32 (+) EM11, drivers kick panel. White 58
Starter Gray 9 (+) EM11, drivers kick panel. White 58
EMS COM Brown/Orange or Blue 41 Data EM11, drivers kick panel. White 58
Wire Information Connector Information
Kia Optima (Smart Key) 2014-2015
Kia Optima Hybrid (Smart Key) 2014-2016
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
(-) PTS Output 1: Green/Black: 2
(-) Parking Lights Output: Red/Black: 4
(+) Starter Output: Gray/Black: 7
EMS COM Data: Orange/Black: 11
(-) PTS Output 2: Black/White: 1
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
(-) Parking Lights: Pink, pin 14
1 8
169
OBDIIDiagnosticconnector C-CAN High: White, pin 6
C-CAN Low: Brown, pin 14
B-CAN High: Orange, pin 13
B-CAN Low:Blue, pin 1
White Conn. I/P-G(Back of I/P Junction Box,
located left side of dash panel)
24
12
23
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
EMS COM Data:Blue/Orange, pin 37
(+) Ignition 1:Pink, pin 58
(+) Ignition 2:White, pin 32
(+) Starter: Green, pin 49
39
172
50
49
40
29
28
183
7 22
14
54
44
36
6 21
13
53
43
35
42
34
12
4
205
19
52
11
51
41
33
45
37
1 16
27
38
48
26
32
58
56
57
31
30
47
46
25
24
10
9
238 15
55
White Conn. EM11(Driver Kick Panel)
(+) Ignition 1 Output: Gray: 6
White Conn. M01-L(at Headlight Switch)
8
16
7
15
6
145
13
4
12
3
11
2
10
1
9
HS CAN Low: Tan: 4
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) Ignition 2 Output: Yellow: 8
HS CAN High: Tan/Black: 3
(+) 12V: Red: 13
(-) Ground: Black: 14
(+) 12V: Brown: 7
30
30
86
86
85
85
87
87
87a
87a
Fuse30A
Fuse30A
(+) 12V
(+) 12V
Installation Type 6Page 13
10
RF
Prog. Button
LED
4
12
14
2
10
DBALL/DBALL2
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Fuses
I/P Junction Box(Left Side of Dash Panel)
(+) 12V:Green,pin 1
2 31
Black conn.(front of I/P
Junction Box)
Hood Pin
Remote Start Safety Override Switch
6: White/Black: (-) Hood
Note: hood pin only required on vehicles not equipped with a factory hood pin
The Remote Start Safety Override Switch MUST be in the OFF position.
(-) PTS 1:Yellow/Black,
pin 1
Black conn. M04(at Push-to-Start button)
1 2
87
3
9
4
10
5
11
6
12
(-) PTS 2:Yellow/Orange, pin 8
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 6 - Vehicle Wiring Reference ChartPage 14
Function Color Pin Polarity Location Color Pins
12V Green 1 (+) I/P-C, front of drivers I/P junction box. Black 3
PTS 1 Yellow/Black 1 (-) M04, Push-to-Start Button. Black 12
PTS 2 Yellow/Orange 8 (-) M04, Push-to-Start Button. Black 12
Parking Lights Pink 14 (-) M01-L, headlight switch. White 16
C-CAN High White 6 Data ODBII. Black 16
C-CAN Low Brown 14 Data ODBII. Black 16
B-CAN High Orange 13 Data I/P-G, back of drivers I/P junction box. White 24
B-CAN Low Blue 1 Data I/P-G, back of drivers I/P junction box. White 24
Ignition 1 Pink 58 (+) EM11, drivers kick panel. White 58
Ignition 2 Orange 32 (+) EM11, drivers kick panel. White 58
Starter Green 49 (+) EM11, drivers kick panel. White 58
EMS COM Brown/Orange or Blue 37 Data EM11, drivers kick panel. White 58
Wire Information Connector Information
Kia Rondo (Smart Key) 2014-20161W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
(-) PTS Output 2: Green/Black: 2
(-) Parking Lights: Red/Black: 4
(+) Starter Output: Gray/Black: 7
EMS COM Data: Orange/Black: 11
(-) PTS Output 1: Black/White: 1
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
1 8
169
OBDIIDiagnosticconnector
C-CAN High:White, pin 6
C-CAN Low: Red, pin 14
White or Black conn. EM11(Driver Kick Panel)
29
38
19
28
110
30
37
20
27
1118
29
31
32
33
34
35
36
12
13
14
15
16
17
21
22
23
24
25
26
34
56
78
(-) Parking Lights: Blue, pin 2
White conn. M14-L(at Headlight Switch)
1 2 63 74 85 9 10 11 12 13
EMS COM Data:Blue/Orange, pin 15
White conn. I/P-M(Back of I/P Junction Box,
located left side of dash panel)
White conn. I/P-C(Front of I/P Junction Box,located left side of dash panel)
B-CAN High:Black, pin 5
B-CAN Low:White, pin 6
(+) Ignition 1: Red, pin 28
(+) Ignition 2:White, pin 38
(+) Starter: Green, pin 37
8
16
7
15
6
14
5
13
4
12
3
11
2
10
1
9
46
36
26
21
111
29
22
24
34 14 29
39
5 15 30
40
6
17
31
41
7
16
32
42
8 18 33
43
10
23
25
12
12
27
34
37
44
13
13
28
35
38
45
(+) Ignition 1 Output: Gray: 6
2615 16 17 18 19 20 21 22 23 24
4 5 6 7 8 9 10 11 132 3
2514
121
(-) Driver Door Trigger:Red/Black, pin 6
White conn. I/P-K(Front of I/P Junction Box,
located left side of dash panel)
(-) Autolights Off Output: Blue/Red: 12
HS CAN Low: Tan: 4
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) Ignition 2 Output: Yellow: 8
HS CAN High: Tan/Black: 3
(+) 12V: Red: 13
(-) Ground: Black: 14(-) Ground
(+) 12V: Brown: 7
30
86 8587
87a
(+) 12V
30
86 8587
87a
(+) 12V
Fuse 30A
Fuse 30A
Installation Type 7Page 15
10
RF
Prog. Button
LED
4
12
14
2
10
DBALL/DBALL2
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Hood Pin
Remote Start Safety Override Switch
6: White/Black: (-) Hood
Note: hood pin only required on vehicles not equipped with a factory hood pin
The Remote Start Safety Override Switch MUST be in the OFF position.
3536
27
8 7 6 5 4 3 2 1
9101112
1920212223242526
1314151617
18
28293031323334
(+) 12V:Red, pin 1
White conn. I/P-B(Front of I/P Junction Box, left side of dash panel)
(-) PTS 2:Yellow/Black,
pin 1
Black conn. M04(at Push-to-Start button)
1 2
87
3
9
4
10
5
11
6
12
(-) PTS 1:Yellow/Orange,pin 8
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 7 - Vehicle Wiring Reference ChartPage 16
Function Color Pin Polarity Location Color Pins
PTS 1 Brown/Black 1 (-) M57, Push-to-Start Button. Black 12
PTS 2 Pink/Black 8 (-) M57, Push-to-Start Button. Black 12
Parking Lights Blue 2 (-) M14-L, headlight switch. White 13
C-CAN High White 6 Data ODBII. Black 16
C-CAN Low Red 14 Data ODBII. Black 16
B-CAN High Black 5 Data I/P-M, back of drivers I/P junction box. White 16
B-CAN Low White 6 Data I/P-M, back of drivers I/P junction box. White 16
Driver Door Trigger Red/Black 6 (-) I/P-K, back of drivers I/P junction box. White 26
12V Red 1 (+) I/P-B, front of drivers I/P junction box. White 36
Ignition 1 Red 28 (+) I/P-E, back of drivers I/P junction box. White 38
Ignition 2 White 38 (+) I/P-E, back of drivers I/P junction box. White 38
Starter Green 37 (+) I/P-C, back of drivers I/P junction box. White 38
Wire Information Connector Information
Kia Sorento (Smart Key) 2014-20151W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
HS CAN Low: Tan: 4
(-) PTS 1 Output : Green/Black: 2
FT CAN High: Orange/Green: 5
(-) Parking Lights: Red/Black: 4
FT CAN Low: Orange/Brown: 6
(+) Ignition 2 Output: Yellow: 8
(+) Starter Output: Gray/Black: 7
EMS COM Data: Orange/Black: 11
HS CAN High: Tan/Black: 3
(-) PTS 2 Output: Black/White: 1
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
(+) 12V: Red: 13
(-) Ground: Black: 14
(+) Starter: Red, pin 1
FT CAN Low: Red, pin 52 FT CAN High:Blue, pin 53
(+) Ignition 1: Blue, pin 25
(+) Ignition 2Blue or White,
pin 31
1 8
169
OBDIIDiagnosticconnector
HS CAN High:Green, pin 6
HS CAN Low:Orange, pin 14
White conn. I/P-E(Back of I/P Junction Box,located left side of dash panel)
31 54
25 30
1 242334
34
8
38
13
43
17
47
5
35
9
39
14
44
18
48
6
36
10
40
15
45
19
49
7
37
11
41
12
42
16
46
20
50
21
51
2928
5333
222
2827
5232
(+) Ignition 1 Output: Gray: 6
(-) Parking Lights: Blue, pin 1
White conn. M20-L(at Headlight Switch)
6 74 85 9 10 11 12 1321 3
(+) 12V: Brown: 7
30
30
86
86
85
85
87
87
87a
87a
(+) 12V
(+) 12V
Fuse 30A
Fuse 30A
EMS COM Data:Blue, pin 7
Yellow conn. MC11(Passenger Kick Panel)
24 18
12 6
23 17
11 5
22 16
10 4
21 15
9 3
20 14
8 2
19 13
7 1
Page 17
Installation Type 8
10
RF
Prog. Button
LED
4
12
14
2
10
DBALL/DBALL2
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Fuses
I/P Junction Box(Left Side of Dash Panel)
(+) 12V:Red, pin 1
Black Conn. I/P-A(front of I/P Junction Box)
2 31
Hood Pin
Remote Start Safety Override Switch
6: White/Black: (-) Hood
The Remote Start Safety Override Switch MUST be in the OFF position.
Black conn. M04(at Push-to-Start button)
10
5
9
4
83
72
61
(-) PTS 2:White,
pin 7
(-) PTS 1:White/Black,pin 8
Note: hood pin only required on vehicles not equipped with a factory hood pin
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 8 - Vehicle Wiring Reference ChartPage 18
Function Color Pin Polarity Location Color Pins
12V Red 1 (+) I/P-A, front of drivers I/P junction box. Black 3
PTS 1 White/Black 7 (-) M04, Push-to-Start Button. Black 10
PTS 2 White 1 (-) M04, Push-to-Start Button. Black 10
Parking Lights Blue 1 (-) M20-L, headlight switch. White 13
C-CAN High Green 6 Data ODBII. Black 16
C-CAN Low Orange 14 Data ODBII. Black 16
EMS COM Blue 7 Data MC11, passenger kick panel. Yellow 24
B-CAN High Blue 53 Data I/P-E, back of drivers I/P junction box. White 54
B-CAN Low Red 52 Data I/P-E, back of drivers I/P junction box. White 54
Ignition 1 Blue 31 (+) I/P-E, back of drivers I/P junction box. White 54
Ignition 2 Blue 1 (+) I/P-E, back of drivers I/P junction box. White 54
Starter Red 7 (+) I/P-E, back of drivers I/P junction box. White 54
Wire Information Connector Information
Kia Sportage (Smart Key) 2011-20131W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
HS CAN Low: Tan: 4
(-) PTS 1 Output: Green/Black: 2
FT CAN High: Orange/Green: 5
(-) Parking Lights Output: Red/Black: 4
FT CAN Low: Orange/Brown: 6
(+) Ignition 2 Output: Yellow: 8
(+) Starter Output: Gray/Black: 7
EMS COM Data: Orange/Black: 11
HS CAN High: Tan/Black: 3
(-) PTS 2 Output: Black/White: 1
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
(+) 12V: Red: 13
(-) Ground: Black: 14
(+) Starter: Red, pin 1
FT CAN Low: Red, pin 52 FT CAN High:Blue, pin 53
(+) Ignition 1: Blue, pin 25
(+) Ignition 2Blue or White,
pin 31
1 8
169
OBDIIDiagnosticconnector
HS CAN High:Green, pin 6
HS CAN Low:Orange, pin 14
White conn. I/P-E(Back of I/P Junction Box,located left side of dash panel)
31 54
25 30
1 242334
34
8
38
13
43
17
47
5
35
9
39
14
44
18
48
6
36
10
40
15
45
19
49
7
37
11
41
12
42
16
46
20
50
21
51
2928
5333
222
2827
5232
(+) Ignition 1 Output: Gray: 6
(-) Parking Lights: Blue, pin 1
White conn. M20-L(at Headlight Switch)
6 74 85 9 10 11 12 1321 3
(+) 12V: Brown: 7
30
30
86
86
85
85
87
87
87a
87a
(+) 12V
(+) 12V
Fuse 30A
Fuse 30A
EMS COM Data:Blue, pin 7
Yellow conn. MC11(Passenger Kick Panel)
24 18
12 6
23 17
11 5
22 16
10 4
21 15
9 3
20 14
8 2
19 13
7 1
Page 19
Installation Type 9
10
RF
Programming button
LED
4
12
14
2
10
DBALL/DBALL2
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Fuses
I/P Junction Box(Left Side of Dash Panel)
(+) 12V:Red, pin 1
Black Conn. I/P-A(front of I/P Junction Box)
2 31
Hood Pin
Remote Start Safety Override Switch
6: White/Black: (-) Hood
The Remote Start Safety Override Switch MUST be in the OFF position.
Note: hood pin only required on vehicles not equipped with a factory hood pin
Black conn. M04(at Push-to-Start button)
1 2
87
3
9
4
10
5
11
6
12
(-) PTS 2:White,
pin 1
(-) PTS 1:White/Black,pin 8
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 9 - Vehicle Wiring Reference ChartPage 20
Function Color Pin Polarity Location Color Pins
12V Red 1 (+) I/P-A, front of drivers I/P junction box. Black 3
PTS 1 White/Black 8 (-) M04, Push-to-Start Button. Black 12
PTS 2 White 1 (-) M04, Push-to-Start Button. Black 12
Parking Lights Blue 1 (-) M20-L, headlight switch. White 13
C-CAN High Green 6 Data ODBII. Black 16
C-CAN Low Orange 14 Data ODBII. Black 16
EMS COM Blue 7 Data MC11, passenger kick panel. Yellow 24
B-CAN High Blue 53 Data I/P-E, back of drivers I/P junction box. White 54
B-CAN Low Red 52 Data I/P-E, back of drivers I/P junction box. White 54
Ignition 1 Blue 31 (+) I/P-E, back of drivers I/P junction box. White 54
Ignition 2 Blue 1 (+) I/P-E, back of drivers I/P junction box. White 54
Starter Red 7 (+) I/P-E, back of drivers I/P junction box. White 54
Wire Information Connector Information
Kia Sportage (Smart Key) 2014-20161W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
HS CAN Low: Tan: 4
(-) PTS Output 2: Green/Black: 2
FT CAN High: Orange/Green: 5
(-) Parking Lights: Red/Black: 4
FT CAN Low: Orange/Brown: 6
(+) 12V: Brown: 7
(+) Ignition 2: Yellow: 8
(+) Starter Output: Gray/Black: 7
EMS COM Data: Orange/Black: 11
HS CAN High: Tan/Black: 3
(-) PTS Output 1: Black/White: 1
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
(+) 12V: Red: 13
(-) Ground: Black: 14
Blue or Black conn. JM02(Left side of I/P Junction Box,
located left side of dash panel)
1 8
169
OBDIIDiagnostic connector
C-CAN High: Red, pin 6
C-CAN Low: Blue, pin 14
B-CAN High: Brown, pin 9
(+) 12V: Red, pin 1
B-CAN Low: White, pin 19
(-) Parking Lights:Pink/Black, pin 2
White conn. M02-L(at Headlight Switch)
1 2 63 74 85 9 10 11 12 13
(+) Starter:Red or White,pin 3
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
15
6313 14 16
74
17
85
18
9
19
10
20
11
1
21
12
2
Black conn. I/P-D(Front of I/P JunctionBox, located on leftside of dash panel)
(-) Autolights Off Output: Blue/Red: 12
White conn. MF31 (Driver Kick Panel)
(-) Driver Door Trigger: Green, pin 2
(+) Ignition 1 Output: Gray: 6
35
15
25 5
37
17
27 7
38
18
28 8
34
14
24 4
310
1141
131
13
20
23
30
33
40
29
12
19
22
29
32
39
36
16
26 21 6
EMS COM Data:Blue/Black, pin 36
White conn. EM 11(right side of I/P Junction Box,
located left side of dash panel)
(+) Ignition 1: Green, pin 25
White conn. I/P-B(Back of I/P Junction Box,
located left side of dash panel)
31
54
25
30
124
23
34 34
8 38
13
43
17
47
5 35
9 39
14
44
18
48
6 36
10
40
15
45
19
49
7 37
11 41
12
42
16
46
20
50
21
51
29
28
53
33
22
2
28
27
52
32
30
86 8587
87a
Fuse30A
(+) 12V
White conn. I/P-A(Back of I/P Junction Box,
located left side of dash panel)
Page 21
Installation Type 10
10
RF
Prog. Button
LED
4
12
14
2
10
DBALL/DBALL2
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
1
2
Hood Pin
Remote Start Safety Override Switch
6: White/Black: (-) Hood
Note: hood pin only required on vehicles not equipped with a factory hood pin
The Remote Start Safety Override Switch MUST be in the OFF position.
(+) Ignition 2: Green, pin 31
30
86 8587
87a
(-) PTS 1: Pink
Smart Key Module Harness(back of fusebox)
(-) PTS 2: Gray/Black
Fuse30A
(+) 12V
111 212 3
17
4
30
18
5
31
19
6
32
20
7
33
21
8
34
22
9
35
23
10
36
13
1424 1525 1626
2737 2838 2939
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Type 10 - Vehicle Wiring Reference ChartPage 22
Function Color Pin Polarity Location Color Pins
12V Red 1 (+) I/P-D, front of drivers I/P junction box. Black 2
Parking Lights Pink/Black 2 (-) M02-L, headlight switch White 13
C-CAN High Red 6 Data ODBII. Black 16
C-CAN Low Blue 14 Data ODBII. Black 16
B-CAN High Brown 9 Data JM02, left side of drivers I/P junction box. Blue or Black 20
B-CAN Low White 19 Data JM02, left side of drivers I/P junction box. Blue or Black 20
Starter White or Red 3 (+) I/P-A, back of drivers I/P junction box. White 21
EMS COM Blue/Black 36 Data EM11, right side of drivers I/P junction box. White 41
Drivers Door Trigger Green 2 (-) MF31, driver kick panel. White 39
Ignition 1 Green 25 (+) I/P-B, back of drivers I/P junction box. White 54
Ignition 2 Red 1 (+) I/P-B, back of drivers I/P junction box. White 54
PTS 1 Pink N/A (-) Smart Key Module harness, back of fusebox. N/A N/A
PTS 2 Gray/Black N/A (-) Smart Key Module harness, back of fusebox. N/A N/A
Wire Information Connector Information
Kia Rio (Smart Key) 2012-20161W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Page 23
SmartStart/XL202 Installation Notes
The optional XL202 and antenna are not included and MUST be purchased separately.
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
4
4
XL202
An
ten
na
XOVER
SmartStart is optional and not included. It MUST be purchased separately.
SmartStart is optional and not included. It MUST be purchased separately.
The DBALL Remote Start Ready (RSR) solution offers three (3) configuration options to control your system; 3x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL202.
Configuration Wires (Gray & White)Connect Gray wire to (-) Ground
5 pins
D2D (4 pins, white)
4 pins
2 pins, not usedCABLE
CABLE
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL package.2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
SmartStart Revision B
RF Kit
RF Kit & PKE Combination
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
RF Kit, PKE & SmartStart BT Combination
SmartStart Revision A
DBALL/DBALL2
DBALL/DBALL2
DBALL/DBALL2
LED
Prog.Button
D2D (4 pins, white)
4 pins
2 pins, not used
OR
SmartStart
Configuration Wires (White & Brown or Blue)Cut Brown or Blue Loop
LED
THIS SIDE UP
LED
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Page 24
Module Programming
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
ImportantMake all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit available functions and features.
1. Connect the interface module to your computer using the XKLoader.
2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware that is currently saved on the interface module will be indicated in the top right corner of the page.
3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.
4. In the search result page, select Config for RSR, and follow the instructions provided on the screen.5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.6. The following message will be displayed when the upload is completed:
“The flashing is successfully completed. You may now unplug the kit.”You can now proceed with the programming instructions below.
1
2
10-pinD2D
st1
12-pin14-pin
nd2
rd3
&Solid
Connect the 10-pin, 12-pin and 14-pin harnesses to DBALL, then wait until the LED turns ON solid red.
10-pinD2D
XL202
10-pinD2DSmartStart
OR
The DBALL module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL.
a. To ensure that the D2D communication between SmartStart and DBALL works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart).
b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by the DBALL D2D connector.
Connect SmartStart to DBALL using the D2D port.
SmartStart Installation
Connect XL202 to DBALL using the D2D port.
XL202 Installation
Go to the next page to complete the module programming.
Refer to the LED Diagnostics section on pages 28-29 for more information and for troubleshooting purposes.
Key Inside the Vehicle
HOLDMake sure the key is inside the vehicle.
3Turn the ignition knob to RUN position.
For Vehicles with Knob
Press the Push-to-Start (PTS) button twice to turn the ignition ON.
For Vehicles with PTS
Important: Do NOT press the brake pedal.Important:
2XENGINESTARTSTOP
PUSHDo NOTpress the brake pedal
Turn Knob
Key to Run
RU N C C A S T A RF
TF O
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
The LED flashes orange for few seconds to indicate the module is in learningmode then the LED turns ON solid green for 3 seconds and shuts off.The module is now programmed.
4 &&OffFlashes
Orange
Solid
x3 secs
Turn the ignition knob to the OFF position.
51X
ENGINESTARTSTOP
PUSH
Press the Push-to-Start (PTS) button once more to turn the ignition OFF.
Turn Knob
Key to Run
RU N C C A S T A RF
TF O
For Vehicles with Knob For Vehicles with PTS
You have successfully completed the module programming sequence.
Module Reset
2 & &Solid SolidRelease
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red.
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-pin
nd2
rd3
th4
Page 25
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Page 26
2
Solid
&
Solid Flashes
&
Release
3
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Release the programming button. The LED turns ON solid red.
Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-pin
nd2
rd3
th4
Hard Reset
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Feat. Operation Flashes / Option Description
1. No RF Output* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Driver priority*Unlocks only the driver door on first press and unlocks all doors on a second press within 5
seconds.
2. All Unlocks all doors on first press.
1. DisabledThe OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will
be executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.
2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will
unlock at the beginning of the sequence, and relock after start and shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the
vehicle in the remote start sequence, only when required. The reason for this is, factory alarm
control must often be done by lock or unlock operation. This could create unnecessary actions on
door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will
monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is
unlocked or is not equipped with factory alarm, the
disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter
actions so that the factory alarm control is not done twice. A remote starter, for which the Safelock
feature is active, will work perfectly with this option and will make it invisible to the user.*Default
Unlock Driver Priority
Smart OEM Alarm
Control
1 RFTD Output Type
2
3
Feature & Option List
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, a manual configuration of the features is possible using the information on this page.
Page 27
To enter feature programming routine- Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.- The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Changing feature options- Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the
DBALL in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will change the option for the selected feature.
- The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.
Exiting feature programming- No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.OR
- Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.
Feature Programming Programming Button
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Page 28
LED Diagnostics & Troubleshooting
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
LED Description Troubleshooting
Module has no power.
Make sure the D2D harness is connected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Waiting to begin the programming sequence.Ensure the correct programming procedure is being
followed.
Initialization failed.Reset the module and complete the programming again.
If the issue persists, please contact Technical Support.
Transponder functions were skipped.
(If compatible) when RXT mode is not desired or
convenience features are needed, please reset and
reprogram the module.
All required CAN networks has been detected. Normal operation.
1 of 2 CAN networks has been detected. Normal operation
Key2GO initiated.Please follow the steps indicated in “Module
programming” to complete the Key2GO programming.
Module was successfully programmed with all functions. Normal operation
Module was successfully programmed without
transponder functions.Normal operation.
CAN2 not detected.
Check the CAN2 Orange/Green and Orange/Brown wire
connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not
require this connection, skip this step by pressing the
programming button 5 times.
J1850 not detected.Check the J1850 wire connection. Wake up the data bus
by turning the ignition on and try again.
CAN1 not detected.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try
again. If your installation does not require this
connection, skip this step by pressing the programming
button 5 times.
Bypass data not detected.
Check the bypass line connection. If more than one wire
is used, make sure they are not inverted. Ensure the
vehicle still operates correctly using the factory key.
Bypass processing error.
The bypass calculation failed. Reset the module and try
again. If the condition persists, please contact Technical
Support.
ISO 1 not detected.
The Yellow/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
ISO 2 not detected.
The Orange/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
MUX not detected.
The Violet/Green or Violet/Brown wire did not detect the
expected voltage value. Refer to "Installation (wiring
diagrams & vehicle wiring reference charts)" to check
the connections.
Module Programming
Module Programming - Error Codes
Solid red
Flashes redx 1
Flashes redx 1
Flashes redx 2
Flashes redx 3
Flashes redx 4
Flashes redx 5
Flashes redx 6
Flashes redx 7
Solid greenx 3 secs
Flashesgreen
Solid orange
Flashes red& green
Off
Flashesorange
Flashesorangeslowly
Solid orangex 3 secs
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
LED Description Troubleshooting
OBDII feature is not supported.The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
Ground When Running (Status) command received. The module has initialized the remote start sequence.
Ignition ON command received.The module has received the Ignition ON command and
is processing the remote start sequence.
Start ON command received.The module has received the Start ON command and is
processing the remote start sequence.
PTS shutdown error.The PTS output from the module was not activated due
to safety protection.
CAN bus incorrectly detected.
Verify the CAN1 and CAN2 connections. Refer to
“Installation (wiring diagrams & vehicle wiring reference
charts)” to check the connections.
LOCK command received.
UNLOCK command received.
TRUNK command received.
AUX1 command received.
AUX2 command received.
AUX3 command received.
Takeover successful. Normal operation.
Runsafe was not disabled.No UNLOCK command was received prior to opening the
door, or the 45 second timer expired in takeover mode.
Brake was not detected.The brakes were not detected, which prevents the
system from shutting down the vehicle.
Smart key was not detected.The smart key was not detected, which prevents the
system from shutting down the vehicle.
Speed was detected.The vehicle was detected as moving, which prevents the
system from shutting it down.
External module synchronization
Commands
Activation Ground When Running (Status)
If the bypass module fails to flash, it did not receive the
signal. Commands can come from RF or D2D.
Shutdown codes
(Flashes red,red thenorange) x 10
Flashes red& orange
Flashes redx 21
Flashes redx 2
Flashes redx 4
Flashes redx 10
Flashes redx 1
Flashes redx 3
Flashesgreen
Flashesgreenquickly
Flashesgreen x 1
Flashesorange x 1
Flashesorange x 2
Flashesorange x 3
Flashesorange x 5
Flashesorange x 4
Flashesorange x 6
Page 29
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Page 30
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Flashes Diagnostic
1 Runtime expired.
2 Over-rev shutdown.
3 Low/No RPM.
4 Transmitter shutdown.
5 Brake shutdown.
6 Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.
* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.
Parking Light Error Codes
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Rev.: 20170505
Platform: DBALL/DBALL2Firmware: HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Limited One Year Consumer WarrantyPage 31
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
1W
7.5 Amp
Diode 1k
Wire jump template
White conn. M20-R(at steering column)
1 3 52 4 67 9 118 10 12
[1] (-) Horn: White or Gray, pin 6
(-) PTS 1:Yellow/Black,
pin 1
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information.the Module Programming section on page n
Quick Reference GuideDBALL/DBALL2-HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
1
2
3
Stop the vehicle in a safe parking spot and put the gear in Park (P).
Press remote start
button*
* Your aftermarket remote may differ from the model shown in the illustrations.
Stop & put vehicle in Park (P)
P&
Flashes
ENGINESTARTSTOP&
HOLD
Exit vehicle with Smart Key
Pit Stop Mode
The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.
Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.
It is now safe to leave the engine running and exit the vehicle with the factory remote in hand.
Press the button to remote start the vehicle.*
The PTS button will flash once to indicate the vehicle is now in Pit Stop Mode.
Parking Light Error CodesThe parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.
Flashes Diagnostic
1 Runtime expired.
2 Over-rev shutdown.
3 Low/No RPM.
4 Transmitter shutdown.
5 Brake shutdown.
6 Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.
Vehicle Takeover
HOLD
5
3
1Close the vehicle doors, hood and trunk, then press the Remote Start button on the transmitter to start the vehicle.*
2
Depress the brake pedal, put the carin gear and drive off.
Enter the vehicle, while making sure the factory remote is inside with you.
Press the Unlock button on the factory or aftermarket remote.*
Ready to drive off
Press remote start
button**
Press Unlock button on
either remote**HOLD OR
Enter vehicle with key fob
* Your aftermarket remote may differ from the model shown in the illustrations.
Complete the following steps within 45 secondsor the vehicle will shut down.
4 Press twice on the PTS switch.
�佒L �� A�
佃 呅剆
G畩摥猠�慮�楳�楳灯湩扬敳甠睷w�摡瑡汩湫�潭
块 偐佒
W��T�����单 T A畴潭潴楶攠D慴愠S潬畴楯湳 I湣����
Hyundai Genesis Sedan with Smart Key
©2010DirectedElectronics.Allrightsreserved.
("Push-button Start")
Hyundai proximity key solution
Quick Reference GuideDBALL/DBALL2-HYUNDAI2 Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Button(s) Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press once, then to activate the
rear hatch/tail glass release (optional).*
Press 3 times, then to activate
the panic mode.
Press once, then to reset the
remote starter runtime.
List of Available Commands
x1 +
x3 +
x1 +
* This output is configurable. see your authorized installation center for more information.
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.
Remote Start Ready (RSR)
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
SmartStart Compatible
This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.
What is SmartStart?
Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system:
Ÿ Lock/ArmŸ Unlock/DisarmŸ Remote Car StarterŸ Trunk ReleaseŸ PanicŸ Aux Channels
You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart!
But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more.
3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.
For more information, visit www.mysmartstart.com.
3x OEM Lock Remote Start Activation
This solution includes the option to remote start your vehicle by pressing the Lock button 3 times consecutively. If your vehicle allows the OEM remote to remain active while the engine is running, you may shut down your remote starter by pressing the Lock button 3 times once more.
Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it.
�佒L �� A�
佃 呅剆
G畩摥猠�慮�楳�楳灯湩扬敳甠睷w�摡瑡汩湫�潭
块 偐佒
W��T�����单 T A畴潭潴楶攠D慴愠S潬畴楯湳 I湣����
Hyundai Genesis Sedan with Smart Key
©2010DirectedElectronics.Allrightsreserved.
("Push-button Start")
Hyundai proximity key solution