dball2-gm9 en ig lt20170828 - microsoft · 2017-08-28 · chevrolet cruze (smart key) 2012-2016...

Installation Guide

Update Alert: Firmware updates are posted the web on a regular basis. We recommendon

that you check for firmware and/or install guide updates prior to installing this product.

Vehicle Application Guide ....... .................. ..................................... ............................... ......................................................

Key2 & 1 .............. ....... .................. ....GO KEY ................................ ............................... ......................................................

Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )Type 1.............. ..... .................................................................................................................... ..........................................Type .............. ..... ..........................................2 .......................................................................... ..........................................Type 3.................................................................................................................................................................................

ProgrammingModule Programming ...................... .............................................................................. .......... ...........................................Keyport Location........ ...................... .............................................................................. .......... ...........................................Module Reset.. ...................................................................................................................................................................Hard ... ....Reset.. ................................................................................................................................................................Feature & Option List..........................................................................................................................................................Feature Programming.........................................................................................................................................................

LED Diagnostics & Troubleshooting...................................................................................................................................

Limited One-Year Consumer ........Warranty.......................................................................................................................

Quick Reference Guide......................................................................................................................................................

02

03

040709

111314141516

17

19

20

Index

® , Chevrolet and GMC their respective companiesBuick, Cadillac are registered trademarks and property of .

Key2 is required.GO

Important!▪This guide is compatible with the 9 firmware version 2.0 and later.GM 6

The 9 firmware for 2 is an all-in-one door lock and override module compatible withGM DBALLspecific Buick, Cadillac, Chevrolet and GMC vehicles.

This module can only be flashed and configured using Xpress at www.directechs.com orVIPusing the Directechs Mobile application for smartphones. Refer to the Module Programmingsection 11on page for more information.

Rev.: 20 0817 28

Platform: DBALL2

Firmware G 9: M v.2.0 +6

© 2017 Directed. All rights reserved.

Vehicle Application Guide

The following table lists the vehicles and features which are compatible with this product. The number assigned to eachyear allows you to determine which installation type should be used for your vehicle.

Vehicles

2018

2017

2016

2015

2014

2013

2012

2011

2010

PK

-Im

mobilizer

Bypass-D

ata

No

Key

Req'd

DL-A

rmF

acto

ryS

ecurity

DL-D

isarm

Facto

ryS

ecurity

DL-D

oor

Lock

Contr

ol

DL-D

oor

Unlo

ck

DL-D

river

Priority

Unlo

ck

DL-T

runk

/H

atc

hR

ele

ase

FO

B-C

ontr

ol o

fafterm

ark

etala

rmw

ithO

EM

rem

ote

Key2G

O

RS

-RA

PS

hutD

ow

n(R

eta

ined

AC

CP

ow

er)

RS

-Tach

/R

PM

Outp

ut

SS

-Entr

yM

onito

ring

ALL

Door

Pin

s

SS

-Entr

yM

onito

ring

Hood

Pin

SS

-Entr

yM

onito

ring

Tru

nk/H

atc

hP

in

SS

-Facto

ryA

larm

Trigger

Monito

ring

ST

-Bra

ke

Sta

tus

(footbra

ke)

ST

-E-B

rake

Sta

tus

ST

-Igniti

on

Sta

tus

Buick

LaCrosse (Smart Key) 1 1 1 1 1 1 1 • • • • • • • D • • • • • • D • • •

Regal (Smart Key) 1 1 1 1 1 1 1 • • • • • • • D • • • • • • D • • •

Verano (Smart Key) 1 1 1 1 1 1 • • • • • • • D • • • • • • D • • •

Cadillac

ATS (Smart Key) 2 2 2 2 • • • • • • • D • • • • • • D • • •

CTS Sedan (Smart Key) 2 2 2 • • • • • • • D • • • • • • D • • •

Escalade (Smart Key) 2 2 2 • • • • • • • D • • • • • • D • • •

SRX (Smart Key) 1 1 1 1 1 1 1 • • • • • • • D • • • • • • D • • •

XTS (Smart Key) 1 1 1 1 • • • • • • • D • • • • • • D • • •

Chevrolet

Cruze (Smart Key) 1 1 1 1 1 1 • • • • • • • D • • • • • • D • • •

Impala (Smart Key) 1 1 1 1 1 • • • • • • • D • • • • • • D • • •

Malibu (Smart Key) 3 3 1 1 1 • • • • • • • D • • • • • • D • • •

Suburban (Smart Key) 2 2 2 • • • • • • • D • • • • • • D • • •

Tahoe (Smart Key) 2 2 2 • • • • • • • D • • • • • • D • • •

GMC

Yukon (Smart Key) 2 2 2 • • • • • • • D • • • • • • D • • •

Legend:

D: Data-to-Data (D2D) only PK: Transponder & Immobilizer Override

•: D2D & Wire-to-Wire (W2W) DL: OE Door Lock & Alarm Controls

FOB: Sync CAN Interface w/ FOB Remote

RS: Engine Start & Status

SS: Entry Point Status-Security

ST: Function/Feature Status

Rev.: 20 0817 28

Platform: DBALL2



This feature is mandatory to control the immobilizer override in this firmware.

Key2 has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It usesGOan array of servers to generate a duplicate of the original key, the installation of a remote starter without having toallowinggive up a key.

The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.

All Key2 -compatible firmware are clearly indicated in the function list of each vehicle search result page and will alsoGOappear on the flash page. Any first-time user must re-register to gain access to Key2 , and some additional informationGOwill be required to complete the registration process, such as your Directed account number and store name.

Key2 is compatible with Xpress 4.5 or higher and requires an oader.GO VIP XKL

Refer to page 2 of this guide for instructions on how to program features using Key2 .1 GO

Rev.: 20 0817 28

Platform: DBALL2



1 2 3 45 6 7 8

9 10

17

23

16

22

11 12

18

24

13

19

25

14

20

26

15

21

27

1 2 3 45

8 9 10 11 12 13 14

15 17 19

23 25

16

22

18 20

24 26

6 7

Not required in D2D mode.

1: (-) Lock InputGreen:

2: (-) Unlock InputBlue:

3: (-)Red/White: Trunk Release Input

4: (-)White/Violet: Tailgate Input

8: (+) Starter InputViolet:

9: (+) Ignition InputPink:

10: (-) (Status) InputBlue/White: GWR

Single Wire : 1CAN Light Green:

SW CAN: pin 22

180Ω

HS CAN Low:pin 23

HS CAN High:pin 24

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

(-) Clutch Output: 11Yellow/Red:

(-) Ground 12: Brown/Red:

(-) Ground: 14Black:(-) Ground

(+) 12V: 13Red:(+) 12V

( ) Tach OutputAC : 5Violet/White:

(+) Brake Status Output: 6Gray:

(-) E-Brake Status 1: Black/White:

(-) E-Brake Status Input

(-) Door/Trunk Status: 3Green/White:

(+) Ignition Status Output: 7Gray/Black:

Immo. Data (conn. side): 10Yellow/Black:

(MUX) Brake Activation Output: 9Violet/Brown:

(-) Hood Status: 12Blue/Red:

Rem

ote

Sta

rter

(-) (Status)GWR Output

(+) Ignition putIn

(-) OutputLock

(+) Starter Output

(-) OutputAUX

(-) OutputUnlock

(-) Trunk Release Output

(-) Trunk Status InputDoor/

(-) Parking Lights Output

(-) Hood Status Input

(+) Brake Status Input

( ) Tach InputAC

(-) Ground

(+) 12V Input

(-) Parking Lights in 22P:

Immo. Data Interr. (conn. side): 8Yellow:

Immo. Data Interr. (veh. side): 9Orange/Yellow:

1

8 9 10 11 12 13 14

17

23

15

21

16

22

18

24

19 20

25

2 3 4 5 6 7

Immo. Data:Green/Violetor Lt. Blue,pin 2

White at BCM

Green at BCM Lt. Blue at BCM (+) 12V: pin 4

Brake: pin 7

BCM

BrownBlue Green GrayWhite PinkBlack

CUT

A B C

Clutch: in Bp

Clutch Switch(b .)lack 3-pin conn

Installation Type 1

[2] Required for manual transmission vehicles.ONLY

[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.

Refer to "Vehicle Wiring Reference Chart - Type 1" on next page for more information on vehicle-specific connections.

With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s

P#: 2D65XKDTX

(-) Ground

RX

(+)12V

10

RF

Prog Button.

LED

4

14

12

2

2DBALL

[3]

[2]

[2]

[2]

[3]

[1]

[1]

[3] Cadillac .SRX ONLY

Rev.: 20 0817 28

Platform: DBALL2



Rev.: 20 0817 28

Platform: DBALL2



Wire colors should only be used as a reference. You should always test a wire's function before connecting to it.

Type 1 - Vehicle Wiring Reference Chart

Function Color Pin Polarity Location Color Pins

Buick LaCrosse (Smart key) 2010

Immo. Data Lt. Blue 2 Data BCM under drivers dash. Green 25

Parking Lights Lt. Blue 22 (-) BCM under drivers dash. White 26

SW CAN Dk. Green 22 Data BCM under drivers dash. Blue 27

HS CAN High Tan/Black 24 Data BCM under drivers dash. Blue 27

HS CAN Low Tan 23 Data BCM under drivers dash. Blue 27

Brake Yellow 7 MUX BCM under drivers dash. Blue 27

12V Red/White 4 (+) BCM under drivers dash. Blue 27

Buick LaCrosse (Smart key) 2011-2012

Immo. Data Green/Violet 2 Data BCM under drivers dash. Green 25

Parking Lights Lt. Green 22 (-) BCM under drivers dash. White 26

SW CAN Lt. Green 22 Data BCM under drivers dash. Blue 27

HS CAN High Dk. Blue 24 Data BCM under drivers dash. Blue 27

HS CAN Low White 23 Data BCM under drivers dash. Blue 27

Brake Dk. Blue 7 MUX BCM under drivers dash. Blue 27

12V Red/Violet 4 (+) BCM under drivers dash. Blue 27

Buick LaCrosse (Smart key) 2013-2016


Parking Lights Green/Brown or Lt. Green 22 (-) BCM under drivers dash. White 26



HS CAN Low Dk. Blue/Yellow 23 Data BCM under drivers dash. Blue 27



Buick Regal (Smart Key) 2012-2014


Parking Lights Green/Gray 22 (-) BCM under drivers dash. White 26

SW CAN Green 22 Data BCM under drivers dash. Blue 27

HS CAN High Blue 24 Data BCM under drivers dash. Blue 27


Brake Blue/Yellow 7 MUX BCM under drivers dash. Blue 27

12V Red/White or Red/Brown 4 (+) BCM under drivers dash. Blue 27

Clutch Output [3] Yellow B MUX Clutch switch. Black 3

Buick Verano (Smart Key) 2012-2016

Immo. Data Green/Violet 2 Data BCM passenger side center console. Green 25

Parking Lights Green/Gray 22 (-) BCM passenger side center console. White 26

SW CAN Green 22 Data BCM passenger side center console. Blue 27

HS CAN High Blue 24 Data BCM passenger side center console. Blue 27

HS CAN Low White 23 Data BCM passenger side center console. Blue 27

Brake Blue/Yellow 7 MUX BCM passenger side center console. Blue 27

12V Red/Brown 4 (+) BCM passenger side center console. Blue 27


Wire Information Connector Information

Rev.: 20 0817 28

Platform: DBALL2



Type 1 - Vehicle Wiring Reference Chart


Cadillac SRX (Smart Key) 2010-2012


Parking Lights Green/Brown or Lt. Green 22 (-) BCM under drivers dash. White 26



HS CAN Low Dk. Blue/Yellow 23 Data BCM under drivers dash. Blue 27



Cadillac SRX (Smart Key) 2013-2016

Immo. Data Lt. Green/Violet 2 Data BCM under drivers dash. Green 25

Parking Lights Lt. Green/Gray 22 (-) BCM under drivers dash. White 26


HS CAN High Tan/Black 24 Data BCM under drivers dash. Blue 27

HS CAN Low Tan 23 Data BCM under drivers dash. Blue 27



Cadillac XTS (Smart Key) 2013-2016

Immo. Data Lt. Green/Violet 2 Data BCM under drivers dash. Green 25

Parking Lights Lt. Green/Gray 22 (-) BCM under drivers dash. White 26


HS CAN High Lt. Blue 24 Data BCM under drivers dash. Blue 27




Chevrolet Cruze (Smart Key) 2012-2016


Parking Lights Green/Gray 22 (-) BCM passenger side center console. White 26


HS CAN High Blue 24 Data BCM passenger side center console. Blue 27

HS CAN Low White 23 Data BCM passenger side center console. Blue 27


12V Red/Gray 4 (+) BCM passenger side center console. Blue 27


Chevrolet Impala (Smart Key) 2014-2016


Parking Lights Green/Gray 22 (-) BCM under drivers dash. White 26






Chevrolet Malibu (Smart Key) 2013-2015


Parking Lights Gray 22 (-) BCM under drivers dash. White 26




Brake Blue 7 MUX BCM under drivers dash. Blue 27



Rev.: 20 0817 28

Platform: DBALL2



1 2 3 45 6 7 8

9 10

17

23

16

22

11 12

18

24

13

19

25

14

20

26

15

21

27

1 2 3 45

8 9 10 11 12 13 14

15

21

17 19

23 25

16

22

18 20

24 26

6 7




3: (-)Red/White: Trunk Release Input





SW CAN:, pin 23Green

HS CAN Low:, pin 24White

HS CAN High: , pin 25Blue(+) 12V: Red/Gray orRed/Violet, pin 4

Immo. Data:,Green/Violet

pin 2


HS CAN Low: 4Tan:


(+) 12V: 13Red:(+) 12V




(-) E-Brake Input Status






Rem

ote

Sta

rter

(-) (Status)GWR Output

(+) Ignition Input

(-) OutputLock

(+) Starter Output

(-) OutputUnlock



(-) Parking Lights Output

(-) Hood Status Input

(+) Brake Status Input

( ) Tach InputAC

BCM

(-) ParkingLights Gray:or Green/Gray,pin 22



1

8 9 10 11 12 13 14

17

23

15

21

16

22

18

24

19 20

25

2 3 4 5 6 7

(+) 12V

1 2 34 5 6 7 8 9

10 11 12 13 14 15 16

17 18 19 20 21

22 24 25 2623

White at BCM

Green at BCM

Lt. Blue at BCM Gray at BCM

Brake:inBlue, p 7


(-) Ground

CUT

(-) Clutch Output: 11Yellow/Red:

(-) Ground 12: Brown/Red:

180Ω

A B C

Clutch: in BP

Clutch Switch(b .)lack 3-pin conn

Installation Type 2


P#: 2D65XKDTX

(-) Ground

RX

(+)12V

10

RF

Prog Button.

LED

4

14

12

2

2DBALL

Refer to "Vehicle Wiring Reference Chart - Type 2" on next page for more information on vehicle-specific connections.


[1]

[1]

[ ]3

[ ]3

[ ]3

[3] Required for manual transmission vehicles.ONLY

Rev.: 20 0817 28

Platform: DBALL2



Wire colors should only be used as a reference. You should always test a wire's function and pin location beforeconnecting to it.

Type - Vehicle Wiring Reference Chart2


Cadillac ATS (Smart Key) 2013-2015

Immo. Data Green/Violet 2 Data BCM behind glove box. Green 25

Parking Lights Gray or Green/Gray 22 (-) BCM behind glove box. White 26

HS CAN High Blue 25 Data BCM behind glove box. White 26

HS CAN Low White 24 Data BCM behind glove box. White 26

SW CAN Green 23 Data BCM behind glove box. Gray 26

Brake Blue/Yellow 7 MUX BCM behind glove box. Blue 27

12V Red/Gray 4 (+) BCM behind glove box. Blue 27


Cadillac CTS (Smart Key) 2013-2015

Immo. Data Green/Violet 2 Data BCM under driver dash. Green 25

Parking Lights Gray or Green/Gray 22 (-) BCM under driver dash. White 26

HS CAN High Blue 25 Data BCM under driver dash. White 26

HS CAN Low White 24 Data BCM under driver dash. White 26

SW CAN Green 23 Data BCM under driver dash. Gray 26

Brake Blue/Yellow 7 MUX BCM under driver dash. Blue 27

12V Red/Gray 4 (+) BCM under driver dash. Blue 27

Chevrolet Suburban (Smart Key) 2015


Parking Lights Green/Gray 22 (-) BCM under driver dash. White 26




Brake White/Green 7 MUX BCM under driver dash. Blue 27

12V Red/Violet 4 (+) BCM under driver dash. Blue 27

Chevrolet Tahoe (Smart Key) 2015-2016








Cadillac Escalade (Smart Key) 2015-2016








GMC Yukon (Smart Key) 2015-2016









1 2 3 45 6 7 8

9 10

17

23

16

22

11 12

18

24

13

19

25

14

20

26

15

21

27

1 2 3 45

8 9 10 11 12 13 14

15 17 19

23 25

16

22

18 20

24 26

6 7




3: (-) Trunk Release InputRed/White:





SW CAN:in 22Green, p

Brake:in 7Blue, p

HS CAN Low:White, p 4in 2

HS CAN , p 5High: in 2Blue


HS CAN Low: 4Tan:


(+) 12V: 13Red:(+) 12V




(-) E-Brake Status






Rem

ote

Sta

rter

(-) (Status)GWR

(+) Ignition putIn

(-) OutputLock

(+) Starter Output

(-) OutputUnlock



(-) Parking Lights

(-) Hood Status

(+) Brake Status

( ) Tach InputAC

(+) 12V

(-) ParkingLights Gray,:

in 22p



1

8 9 10 11 12 13 14

17

23

15

21

16

22

18

24

19 20

25

2 3 4 5 6 7

Immo. Data:Green/Violet,

in 2p

White at BCM

Green at BCM

Lt. Blue at BCM(+) 12V:Red/Brown,pin 4


(-) Ground

BCM

CUT

Installation Type 3



P#: 2D65XKDTX

(-) Ground

RX

(+)12V

10

RF

Prog Button.

LED

4

14

12

2

2DBALL

Refer to "Vehicle Wiring Reference Chart - Type " on next page for more information on vehicle-specific connections.3

[1]

[1]

Rev.: 20 0817 28

Platform: DBALL2



Rev.: 20 0817 28

Platform: DBALL2



Wire colors should only be used as a reference. You should always test a wire's function before connecting to it.

Type - Vehicle Wiring Reference Chart3


Chevrolet Malibu (Smart Key) 2016


Parking Lights Gray 22 (-) BCM passenger side center console. White 26

HS CAN High Blue 25 Data BCM passenger side center console. White 26

HS CAN Low White 24 Data BCM passenger side center console. White 26



12V Red/Brown 4 (+) BCM passenger side center console. Blue 27


Module Programming

5

6

2

3

4

Remove battery from one key fob and make sure that the other key fob islocated more than 10 feet away from vehicle.

Put the key fob (with battery removed) in the keyport.(Refer to "Keyport ocation" on page 13)L .

Leave ignition ON until the LED starts flashing orange slowly.

Press the Push-to-Start button once to turn the ignition OFF. The LEDcontinues to flash orange slowly.

Press press holdand and the Push-to-Start buttononceuntil the ignition turns ON the release. The LED flashesgreen.

Remove

Battery

ENGINESTARTSTOP

HOLD

FlashesOrangeSlowly

FlashesOrangeSlowly

FlashesGreen

Refer to the Diagnostics section on page for more information and for troubleshooting purposes.LED s 17-18

1Solid

Wait until the LED turns solid red.ON

Go to the next page t complete the module programming.o

&

&

&ENGINESTARTSTOP

PUSH1X

ENGINESTARTSTOP

PUSH1X

Important

Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check toensure everything is correct prior to moving onto the next step.

Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP

When the flashing operation is successful, you can proceed with the programming instructions below.

OR

If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses tothe module, then connect the 4-pin D2D harness.

D2D Installation

W W Installation2

If required for your installation, connect the 10-pin and 12-pin harnesses to themodule, then connect the 14-pin harness to the module.

10-pinD2D

1st

12-pin14-pin

2nd

3rd

10-pinD2D

1st

4th

12-pin14-pin

2nd

3rd

Flashing a module using your computer:

1. Connect the interface module to your computer using theXKLoader2.

2. Go to www.directechs.com using Internet Explorer, andselect the button.Flash Module

3. Follow the instructions to select your vehicle, installationtype, and configure your options.

4. Once you have configured the firmware options, click on theFLASH button.

Flashing a module using your smartphone or tablet

1. Connect the interface module to your oader3.XKL

2. Launch the Directechs Mobile app on your smartphone ortablet.

3. Select and follow the on screenFLASH YOUR MODULEinstructions.

Rev.: 20 0817 28

Platform: DBALL2



You have successfully completed the programming sequence.module

3

2

1

Once the configuration is completed, reconnect the module.The LED ON solid .turns green for 3 seconds, then turns off

Click on .Submit Key2G RequestO

Remove the from the vehicle and reconnect it to your computer. The Directechs« web site willmoduleautomatically recognize that you are moving onto the second phase of the programming sequence.

Refer to the LED Diagnostics section for more information and for troubleshooting purposes.Version 4.5 or higher of XpressVIP must be installed on your computer to complete this programming sequence.

Web Programming (for Key2GO)

Solid x3 Secs

&Off

7 Disconnect the module and complete the programming.Key2GO

Rev.: 20 0817 28

Platform: DBALL2



Rev.: 20 0817 28

Platform: DBALL2



Keyport Location

F

Keyport Location Reference

Buick LaCrosse 2014 - 2016 Place the transmitter in the transmitter pocket inside the armrest storage area. A

Buick LaCrosse 2010 - 2013Remove the cupholder from the center console storage area. Place

transmitter in the pocket with the buttons facing up.B

Buick Regal 2011 - 2014Remove the cupholder liner from the center console cupholder. Place

transmitter in the pocket with the buttons facing up.C

Buick Verano 2012 - 2016Remove the cupholder liner from the center console cupholder. Place

transmitter in the pocket with the buttons facing up.D

Cadillac ATS 2013 - 2016Open the center console storage area and the storage tray. Place the

transmitter in the transmitter pocket.E

Cadillac CTS Sedan 2014 - 2016Open the center console storage area and remove the rubber mat. Place the

transmitter in the transmitter pocket.A

Cadillac Escalade 2015 - 2016Open the center console storage area and the storage tray. Place the


Cadillac SRX 2010 - 2016Open the center console storage area and the storage tray. Place the


Cadillac XTS 2013 - 2016Open the center console storage area and the storage tray. Place the


Chevrolet Cruze 2012 - 2016

Remove the plastic trim piece from the small storage area next to the

accessory power outlet toward the front of the console. Push the button on the

transmitter to extend the blade, insert the key blade into the transmitter slot.

F

Chevrolet Impala 2014 - 2016Open the center console and place the transmitter in the transmitter pocket

with the buttons facing the front of the vehicle.A or B

Chevrolet Malibu 2013 - 2016Open the center console and place the transmitter in the transmitter pocket

with the buttons facing the front of the vehicle.A or B

Chevrolet Suburban 2015Open the center console and place the transmitter in the transmitter pocket

with the buttons facing the front of the vehicle.A

Chevrolet Tahoe 2015 - 2016Open the center console and place the transmitter in the transmitter pocket


GMC Yukon 2015 - 2016Open the center console and place the transmitter in the transmitter pocket


Vehicle

A

2

Solid

&

Solid Flashes

&

Release

3

Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsONuntil the andLED starts to flash orange red.

Release the programming button. The turns solid red.LED ON

Warning gainst xecuting a Hard Reset!A EA hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (suchas and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List

1 OR

If required for your installation, c , &onnect the 10-pin 12-pin14-pin harnesses to the module Press hold the. andp , then connect the 4-pin D2D harness.rogramming button

D2D Installation

If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

1st

12-pin14-pin

2nd

4th

3rd

10-pinD2D

1st

5th

12-pin14-pin

2nd

3rd

4th

Module Reset

Hard Reset

2 & &Solid SolidRelease

Wait 3 seconds until the orange then release theLED turns solidONp The then turns solid red.rogramming button. LED ON

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashedto the module using the web config tool will not be affected.

1 OR

If required for your installation, c , &onnect the 10-pin 12-pin14-pin harnesses to the module Press hold the. andp , then connect the 4-pin D2D harness.rogramming button

D2D Installation

If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

1st

12-pin14-pin

2nd

4th

3rd

10-pinD2D

1st

5th

12-pin14-pin

2nd

3rd

4th

Rev.: 20 0817 28

Platform: DBALL2



Feature & Option List

It is recommended to configure all features and options listed below thethe using configuration tool found on the moduleflashing page on www. .comdirectechs . The web offers more options; however, manual configuration of the features ispossible using the information on this page.

* Default Option

Feat. Operation Flashes/Options Description

1. No RF Output* Module is connected to a remote starter using a standard installation.

2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (w hen available).

3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (w hen available).

1. Driver Priority * Unlocks only the driver door on first press and unlocks all doors on a second press w ithin 5 seconds.

2. All Unlocks all doors on first press.

1. Trunk* Will pop the trunk if available.

2. Electric Rear Hatch When available, w ill operate the electric rear hatch.

1. Ttrunk Will pop the trunk if available.

2. Electric Rear Hatch* When available, w ill operate the electric rear hatch.

1. DisabledThe OEM alarm w ill not be controlled by DBALL2 upon remote start. No disarm or arm command w ill be executed at the

beginning or end of the sequence; it must be controlled by the Remote Starter.

2. SafelockSmart OEM Alarm Control w ill behave like a standard Safelock feature on a remote starter. It w ill unlock at the beginning of

the sequence, and relock after start and shutdow n.

3. Enabled*

Smart OEM Alarm Control w ill synchronize w ith the OEM alarm so that it w ill disarm and rearm the vehicle in the remote start

sequence, only w hen required. The reason for this is, factory alarm control must often be done by lock or unlock operation.

This could create unnecessary actions on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm

Control w ill monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is

not equipped w ith factory alarm, the disarm/rearm w ill not be executed. Smart OEM Alarm Control w ill also monitor the remote

starter actions so that the factory alarm control is not done tw ice. A remote starter, for w hich the Safelock feature is active,

w ill w ork perfectly w ith this option and w ill make it invisible to the user.

RFTD Output Type1

5Smart OEM Alarm

Control

2 Unlock Driver Priority

3 Trunk

4 AUX 1

Rev.: 20 0817 28

Platform: DBALL2



Rev.: 20 0817 28

Platform: DBALL2



To enter feature programming routine- Turn t , thenhe ignition .ON OFF- Within 5 seconds, press and the rogramming button turns after 3 seconds . Release theHOLD LED ONp until the orange ( )

Programming button.- The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicateLED LEDwill flash green once slowly red

the current option of feature 1 . repeat(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence willuntil .a new command is entered

Changing feature options- Press the arm or disarm button on aftermarket transmitter to change the option of the selected feature.lock/ unlock/- The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowlyLED LEDred

the number of times to indicate the current feature. repeat until .The flashing sequence will a new command is entered

Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature.- The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly toLED LED

indicate the current option of the current feature. repeat until .The flashing sequence will a new command is entered

When the maximum number of features or options is reached, the will start flashing again from the first feature or option.LED

Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.

Exiting feature programming- No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programmingLED ON

sequence.OR

- Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm theHOLD LED ONend of the programming sequence.

Feature Programming

ProgrammingButton

Rev.: 20 0817 28

Platform: DBALL2



LED Diagnostics & Troubleshooting

LED Description Troubleshooting

Module has no power.

Make sure the D2D harness is connected or that the 12

Volt is present between the red and black wires. If the

12 Volt is present, the module may be defective.

Waiting to begin the programming sequence.Ensure the correct programming procedure is being

followed.

Initialization failed.Reset the module and complete the programming again.

If the issue persists, please contact Technical Support.

Transponder functions were skipped.

(If compatible) when RXT mode is not desired or

convenience features are needed, please reset and

reprogram the module.

All required CAN networks has been detected. Normal operation.

1 of 2 CAN networks has been detected. Normal operation

Key2GO initiated.Please follow the steps indicated in “Module

programming” to complete the Key2GO programming.

Module was successfully programmed with all functions. Normal operation

Module was successfully programmed without

transponder functions.Normal operation.

CAN2 not detected.

Check the CAN2 Orange/Green and Orange/Brown wire

connections. Wake up the data bus by turning the

ignition on and try again. If your installation does not

require this connection, skip this step by pressing the

programming button 5 times.

J1850 not detected.Check the J1850 wire connection. Wake up the data bus

by turning the ignition on and try again.

CAN1 not detected.

Check the CAN1 Tan and Tan/Black wire connections.

Wake up the data bus by turning the ignition on and try

again. If your installation does not require this

connection, skip this step by pressing the programming

button 5 times.

Bypass data not detected.

Check the bypass line connection. If more than one wire

is used, make sure they are not inverted. Ensure the

vehicle still operates correctly using the factory key.

Bypass processing error.

The bypass calculation failed. Reset the module and try

again. If the condition persists, please contact Technical

Support.

ISO 1 not detected.

The Yellow/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

ISO 2 not detected.

The Orange/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

MUX not detected.

The Violet/Green or Violet/Brown wire did not detect the

expected voltage value. Refer to "Installation (wiring

diagrams & vehicle wiring reference charts)" to check

the connections.

Module Programming

Module Programming - Error Codes

Solid red

Flashes redx 1

Flashes redx 1

Flashes redx 2

Flashes redx 3

Flashes redx 4

Flashes redx 5

Flashes redx 6

Flashes redx 7

Solid greenx 3 secs

Flashesgreen

Solid orange

Flashes red& green

Off

Flashesorange

Flashesorangeslowly

Solid orangex 3 secs

Rev.: 20 0817 28

Platform: DBALL2



LED Description Troubleshooting

OBDII feature is not supported.The diagnostic data bus was not detected, therefore the

SmartStart features will be limited.

Ground When Running (Status) command received. The module has initialized the remote start sequence.

Ignition ON command received.The module has received the Ignition ON command and

is processing the remote start sequence.

Start ON command received.The module has received the Start ON command and is

processing the remote start sequence.

PTS shutdown error.The PTS output from the module was not activated due

to safety protection.

CAN bus incorrectly detected.

Verify the CAN1 and CAN2 connections. Refer to

“Installation (wiring diagrams & vehicle wiring reference

charts)” to check the connections.

LOCK command received.

UNLOCK command received.

TRUNK command received.

AUX1 command received.



Takeover successful. Normal operation.

Runsafe was not disabled.No UNLOCK command was received prior to opening the

door, or the 45 second timer expired in takeover mode.

Brake was not detected.The brakes were not detected, which prevents the

system from shutting down the vehicle.

Smart key was not detected.The smart key was not detected, which prevents the

system from shutting down the vehicle.

Speed was detected.The vehicle was detected as moving, which prevents the

system from shutting it down.

External module synchronization

Commands

Activation Ground When Running (Status)

If the bypass module fails to flash, it did not receive the

signal. Commands can come from RF or D2D.

Shutdown codes

(Flashes red,red thenorange) x 10

Flashes red& orange

Flashes redx 21

Flashes redx 2

Flashes redx 4

Flashes redx 10

Flashes redx 1

Flashes redx 3

Flashesgreen

Flashesgreenquickly

Flashesgreen x 1

Flashesorange x 1

Flashesorange x 2

Flashesorange x 3

Flashesorange x 5

Flashesorange x 4

Flashesorange x 6

Limited Consumer WarrantyOne Year

For a period of from the date of purchase of a Directed Electronics remote start or security product, DirectedONE YEARElectronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, theDIRECTEDsecurity or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or materialunder normal use, provided the following conditions are met: the Part was purchased from an authorized dealer;DIRECTEDand the Part is returned to , postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing theDIRECTEDfollowing information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and completeproduct and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to itsintended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation orother causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING, , ,BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY, , ,FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUALPROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY, ;PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS,PRODUCTS DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALLACTS OF.THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR. AINSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS, , , ,AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION, ,LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING, , . A ADIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF,CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE.DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED.TO THE AUTHORIZED DIRECTED DEALER PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE’S .RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL, ,DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL, , , ,LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE, . ,MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED OPTION THEA ’SPARTAS DESCRIBED ABOVE.

This warranty only covers Parts sold within the United States ofAmerica and Canada. Parts sold outside of the United States ofAmerica or Canada are sold “ - ” and shall have , express or implied. Some states do not allow limitationsAS IS NO WARRANTYon how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warrantygives you specific legal rights and you may also have other rights that vary from State to State. does not and hasDIRECTEDnot authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of ’sDIRECTEDwebsite at: www.directed.com

920-10012-01 2013-07

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the selectvehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. : Under noDISCLAIMERcircumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for anyconsequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, norwill they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / databus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of thisproduct be liable for consequential damages sustained in connection with this product and neither assumes nor authorizesany representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; EuropeanPatent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

Rev.: 20 0817 28

Platform: DBALL2



Quick Reference GuideDBALL2-GM9


Vehicle Takeover with Get In and Go*

4

3

1Close the vehicle doors, hood and trunk, then press the Remote Start button on the transmitter to start the vehicle.**

2

Press the brake pedal, put the car in gear and drive off.

Enter the vehicle, while making sure the factory remote is inside with you.

Press the Unlock button on the factory or aftermarket remote.**

Ready to drive off

Press remote start

button**

Press Unlock button on

either remote**OR

** Your aftermarket remote may differ from the model shown in the illustrations.

GG

* Get In and Go connections required.

Get In and Go

Get In and Go is designed to provide users with easy takeover when entering their Push-to-Start (PTS) equipped vehicle, once it has been remote started.

Typically, users would have to remote start their vehicle, then get inside and press the vehicle start button to perform a takeover. There is therefore a physical action required to drive away. With Get In and Go technology, you simply remote start the vehicle, unlock the doors, get in and go... Nothing to do but put the gear in drive and enjoy your vehicle.

This unique feature monitors a variety of parameters such as the key fob, vehicle speed sensor and door sensor, in order to perform takeover securily.

GG

Complete the following steps within 45 secondsor the vehicle will shut down.

Enter vehicle with Smart Key

1

2

3

Stop the vehicle in a safe parking spot and put the gear in Park (P).

Press remote start

button*

* Your aftermarket remote may differ from the model shown in the illustrations.

Stop & put vehicle in Park (P)

P&

Flashes

ENGINESTARTSTOP&

Exit vehicle with Smart Key

Pit Stop Mode

The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.

Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.

It is now safe to leave the engine running and exit the vehicle with the factory remote in hand.

Press the button to remote start the vehicle.*

The PTS button will flash once to indicate the vehicle is now in Pit Stop Mode.

Quick Reference GuideDBALL2-GM9


Button(s) Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock.

Press & hold for 1 second to remote

start.

Press & hold for 5 seconds to activate

the trunk release (optional).

Press once, then to activate the

rear hatch/tail glass release (optional).*

Press 3 times, then to activate

the panic mode.

Press once, then to reset the

remote starter runtime.

List of Available Commands

x1 +

x3 +

x1 +

* This output is configurable. see your authorized installation center for more information.

Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.

Notes

dball2-gm9 en ig lt20170828 - microsoft · 2017-08-28 · chevrolet cruze (smart key) 2012-2016...

Documents