dcs910 dviewcam manual en us

7/29/2019 Dcs910 DViewCam Manual en Us

1/85


2/85

D-Link D-ViewCam User Manual

Table o Contents

Product Overview ........................................................4

System Requirements .............................................4

Introduction ..............................................................5Features ................................................................... 5

Installing Your IP Camera .........................................6

Sotware Installation ...................................................7

Using D-ViewCam ...................................................... 10

Add Camera Wizard ..............................................11

Using D-ViewCam Sotware .................................. 15Main Display Area .................................................. 16

System Board Area................................................17

Select Device and Map Area ................................. 17

Preview Window Area ............................................ 18

Split Screen Area ................................................... 18

Manual Control Area .............................................. 19

Snapshot Button ..............................................19

Start/Stop Manual Recording Button ............... 20Start/Stop 2-Way Audio Button ........................ 21

Freeze Video Display Button ............................ 22

PTZF Control Area.................................................23

Program Control Area ............................................ 24

Setting and Search Area........................................25

Event Action Log Area ........................................... 26

Confguring D-ViewCam ...........................................27

Wizard Mode..........................................................28

Add Camera Wizard .........................................28System Backup Wizard ....................................29

Quick Recording Settings ................................ 33

Expert Mode ..........................................................34

Main Screen Interace ......................................35

Wizard .............................................................. 36

Add Camera Wizard .........................................36

System Backup Wizard ....................................36

System ...................................................................40

Event Action ..................................................... 40

User .......................................................................48

Administrator .................................................... 48

Normal User ..................................................... 49

My Map ............................................................50

Device Setting ........................................................ 53

Inormation .......................................................53

Playback .....................................................................65

Video Search and Playback Management ............. 65

Event Search and Playback Management ............. 68

Frequently Asked Questions ....................................70

D-Link D-ViewCam Features ................................. 70

D-Link D-ViewCam Operation ...............................72

Table o Contents


3/85


Table o Contents

Contacting Technical Support .................................. 78

Warranty .....................................................................79

Registration................................................................84


4/85


Section 1 - Product Overview

To ensure your D-ViewCam system can maintain high video monitoring and recording perormance, certain minimum

system congurations are required. A higher perormance system is required especially when the number o IP cameras

exceeds 9.

Product Overview

System Requirements

* Recording video over a long period o time will consume large amounts o disk space. Make sure that you have enough

disk space available i you want to use recording unction. You can still complete the installation even i you have less

than the suggested ree disk space.

Note:I a mega pixel camera is used with the D-ViewCam application, the minimum system requirement should be

raised to CPU: Intel P-4 3.4GhZ or above with 1GB o memory due to the resources required to process and store

large amounts o image data.


5/85



Introduction

Thank you or purchasing a D-Link IP camera, which provides state-o-the-art camera technology combined with IPnetwork capabilities. You can build a home or small business surveillance system by using D-Link IP cameras and the

latest eatures oered by the D-ViewCam application sotware.

D-ViewCam can automatically locate and add IP cameras in the local network.

Storage management or recording les.

Single and multiple video stream monitoring (up to 32 video channels).

Two-way audio communication.

Intelligent lter and search capabilities or scheduling recording and/or event recording.

Features


6/85



Installing Your IP CameraBeore installing D-ViewCam, please make sure you have installed your D-Link IP camera(s) that will be managed byD-ViewCam.

Step 1

Follow the installation procedures that came with your IP camera(s) to complete the camera installation process.

Step 2

Veriy that you are able to view the video images rom the IP camera(s) by accessing the cameras built-in webconguration page. It is recommended that all IP cameras be installed in the same subnet as your management PCrunning the D-ViewCam sotware.

Step 3

Please reer to page 11 to add IP camera(s) to the D-ViewCam system.

Note:D-ViewCam is optimized or small-scale LAN environment. To protect the system and cameras rom attack romthe Internet, place D-ViewCam behind a frewall or an IP sharing device.


7/85


Section - Installation

Turn on the computer and insert the IP Camera Installation CD into the CD-ROM drive. Below step-by-step instructionswill be shown i you are using Windows XP. However, similar instructions and screens will also be provided or other

Windows operating systems.

When the autorun screen starts, click Install D-ViewCam.

Note: I the Installation Wizard does not start automatically, you can manually start the wizard by double-clicking thesetup.exe fle rom the CD.

Select a language and click OK.

Sotware Installation

Click OK

Click Next to continue.

Click Next


8/85



Click Next to install the sotware into the deault older. Otherwise,click Browse to select a older.

Click Next

Click Next to start the installation process.

Note:The D-ViewCam installation may take several minutes tocomplete.

Click Next


9/85



Click Finish to complete the installation.

Click Finish


10/85

10D-Link D-ViewCam User Manual

Section - Confguration

Using D-ViewCamThis section will show you how to start and congure D-ViewCam.

To start D-ViewCam, select Start > All Programs > D-Link> D-Link D-ViewCam.

Enter Admin as the deault username and leave the passwordblank. Click OK to log into the system.

Note:You can change the admin password by clicking thelockicon or you can skip this step and change your passwordby ollowing the steps on page 48.


11/85



Welcome to the camera wizard. Use this wizard to add your cameras to the D-ViewCam system.

Add Camera Wizard

Note:Use the let or right arrow to navigate the wizard.


Click Next


12/85



Choose which method to add your camera(s). You can choose AutoDiscovery to automatically search or your camera(s), or choose AddManually to add your camera(s) via the cameras IP address. Click Nextto continue.

I you choose Auto Discovery, the system will search all cameras thatare located in the same subnet within a LAN environment. The systemwill place all ound cameras at the deault map called My Map. Click Next

to continue.

I you choose Add Manually, you will need to enter the IP address o thecamera(s). Click Next to continue.


13/85



D-ViewCam shows the detected IP camera(s) inormation. You will be able to schedule which recording type you wishto set or each camera.

24/7 Continuous Recording: Start scheduled recording 24 hours a day, 7 days a week.

24/7 Motion Detection Recording: Continuously monitoring the videos but ONLY make recording when motionis detected.

Ofce Hours Only: Continuously monitoring the videos during oce hours (08:00 AM to 06.00 PM) and ONLYmake recording when motion is detected.

Non-Ofce Hours Only: Continuously monitoring the videos during non-oce hours (06:00 PM to 08.00 AM) andONLY make recording when motion is detected.

Note:Excluding 24/7 Continuous Recording, other schedule recording types can ONLY be activated when motiondetection is confgured on the camera. Please reer to page 55 in the users manual or more inormation.



14/85



Select Yes to add other camera(s), or select No i you have no additionalcamera(s) to add. Click Next to continue.

The Add Camera wizard is now complete. Click Close to access the D-ViewCam main screen interace.


15/85



Using D-ViewCam SotwareD-ViewCam sotware provides advanced security monitoring and device management unctions when used in congurationwith D-Link IP camera(s). D-ViewCam uses IP technology to provide comprehensive management unctions, such assystem controls, live video eeds, and archived recordings. The main user interace includes 10 areas and you may

reer to the table below or more descriptions.

8 9 10 7

6

5

4

3

2

1


16/85



The main screen interace is where live images rom the cameras or e-Map are displayed. For live images, dependingon the split-screen conguration, this area can display images rom multiple cameras. There is an inormation bar oreach image that can be used to identiy a camera and its current status. This bar will not be displayed in high split-screen

conguration such as 10, 16 or 32.

Main Display Area

Camera NameYour camera name will bedisplayed here.

Event StatusThis icon will display the event status. Grey indicatesno event action setting, Green indicates event actionsetting is on, and i the icon is fashing red this

indicates that an event is detected.

RemoveClick to remove the camera romthe display window.

ConfgClick this thumbnail to access the

conguration settings o the camera.

Video StatusThis icon displays the status o your video. Grayindicates video is lost, Green is normal, andRed indicates video is recording.


17/85



This area displays the D-ViewCam logo, system date and time, and version inormation.

System Board Area

This area displays your map and camera(s) in a tree structure.

Select Device and Map Area


18/85



This area will display an image preview o a selected camera rom My Map. I a map is selected (instead o a camera),this preview window will cycle through images rom all o the available cameras, one ater the other.

Preview Window Area

Split Screen AreaSplit ScreenSelect a split-screen display layout by clickingon the desired layout icon. The systemprovides 4, 6, 9, 10, 16 and 32 split screen

modes. To switch to signal camera display,double click on the cameras image. To returnto the previous conguration screen, pressthe Esc key or double click on the screenagain.

RotationControl the rotation o the video monitoring

screen. The live video display will start torotate rom the upper let to the lowerright. Click the rotation icon to startor stop the rotation. I the number ocameras is more than the current splitscreen conguration, the main displaywindow will arrange in multiple pages.You can access all the cameras by usingthe paging mechanism.


19/85



Manual Control Area

Snapshot ButtonClick this button to capture a selected videoimage immediately.

When a camera is selected and live video image can be seen in the main display or preview area, you can take asnapshot using the snapshot button. When this button is pressed, the system will show a dialogue window with thesnapshot image and options as shown below:

Note:You can save the fle in a dierent ormat by typing the fle ormat ater the fle name, such as: .png, .gi, .jpg.

OSD ButtonClick this button to change the contento the overlay inormation and selecta text color.

Browse ButtonClick this button to select a olderwhere the image le will be saved,and then input a le name.

Snapshot Button


20/85



Start/Stop Manual Recording Button

Start/Stop Manual Recording ButtonBy clicking this button you can start or stopmanual recording o video.

When perorming manual recording, the video window will be marked as red and the recording time inormation will bedisplayed in red at the lower right hand corner o the screen.

I you want to manually record multiple videos, ollow these three steps below.

1. Select a group o live videos by pressing and holding the Ctrl key on the keyboard and then click on all thecamera images which you want to record in video display area.

2. To start recording, click the Start Manual Recording button.

3. To stop multiple recording, select the cameras you wish to stop recording by repeating step 1 and then click theManual Record button to stop recording. All video data is recorded in the QVGA or CIF ormat. The rame ratedepends on the camera that you select and should be congured via the cameras web interace.


21/85



Start/Stop 2-Way Audio Button

Start / Stop 2-Way Audio ButtonWith cameras that support two-way audio, you mayselect this button to start or stop two-way audio.

For camera(s) that support audio, D-ViewCam provides two-way audio eatures, which enable a user to start an audioconversation with another person near the camera(s).

To start an audio conversation, rst select a camera and then press the Start/Stop 2-Way Audio button. You can pressthe button again to stop the unction.

Note:I the two-way audio mode is on and you select another camera, the audio conversation session will be automaticallyterminated.


22/85



Freeze Video Display Button

Freeze Video Display ButtonThis button can be used to temporarily stop displayingall live images. I you press this button again, it willresume video display.

Note:This eature only reezes the live image display; all other unctions such as event and recording are not aected.


23/85



PTZF Control AreaPTZF control area provides pan, tilt, zoom and ocus unctions to control the movement o PTZF capable cameras.

ZoomClick + to zoom in and - to zoomout.

FocusClick + or - to adjust the ocus o thecamera in order to obtain a clearerimage.

Go toSelect a preset point or the camera topoint to. For the preset point setting,please reer to page 54.

PT ControlControls to point the camera up,down, let, or right.

Auto PanEnable auto panning on the PTcamera.

Auto PatrolEnable auto patrolling to the preset

location or the PT camera.

SpeedAdjust the pan and tilt speedo the camera.


24/85



Program Control AreaThis area provides you 4 buttons to control the program or obtain help inormation.

On/O ButtonClick this button to shut downD-ViewCam.

Minimize ButtonClick this button to minimizeD-ViewCam to the taskbar.

Help ButtonClick this button or descriptions, denitions anddetails about D-ViewCam.

Auto-Hide ButtonClick this button to enable or disable the auto-hidepanel. With the auto-hide button enabled, this willmake the panel disappear until you mouse overits location. With the Auto-hide button disabled,the panel will always show on the bottom.


25/85



Setting and Search AreaThis area enables you to view the video in ull screen mode by clicking the 1st button. The 2nd button enables you tocongure the system in 2 dierent modes. Last, the 3rd and 4th button enable you to search and playback the video(s)and event(s).

Full Screen ButtonClick this button to switch the video mode toull screen mode. To return to the previousscreen, double click the screen or pressthe Esc key on your keyboard.

Video Search and Playback ButtonClick to search and watch the recorded video,such as scheduled recording, event recordingand manual recording. Please reer to page 65or details.

System Confguration ButtonClicking this button will provide the user withtwo conguration modes, wizard mode andexpert mode.

Event Search and Playback ButtonClick to search and watch the specic eventand recorded system inormation. Please reerto page 68 or more inormation.

S i C f i


26/85



Event Action Log AreaEvent Action Log AreaThis area displays the 20 most recent events andstarts with the most recently recorded event rst. I

you double click an event item, the system will bringup the detail inormation o the event. I there is arecording, you can do playback immediately aterthe recording has completed. Event canceling will behandled according to your system setting.

Event Action DisabledThis icon indicates the event action setting is setto o. You can congure the event on/o in Expertmode.

Event Action EnabledThis icon indicates the eventaction setting is set to on.

Event Action DetectedThis icon indicates that an eventhas been detected.

When event action is enabled, event canceling will be handled according to your system setting:

Automatic event canceling - the cancel event button will be fashing or a pre-determined period o time and thenthe event automatically cancel.

Manual event canceling - the cancel event button will keep fashing until is clicked. Click the cancel event button

and then the system will cancel all active events

S ti C f ti


27/85



Confguring D-ViewCamD-ViewCam application is designed in a way that it can be easily set up or simple home and small business surveillanceapplications. It provides two modes o conguration, wizard mode and expert mode. Wizard mode is designed or basicconguration, including Add Camera, System Backup and Quick Recording Settings. Expert mode is or more advanced

use with comprehensive conguration options. The user can switch between these two modes at any time.

To congure D-ViewCam, ollow the instructions below:

Step 1

Move your mouse pointer to the bottom o the screen i the Setting and Search Area is hidden.

Step 2

The Setting and Search Area will raise automatically.

Step 3

Click the System Confguration button. For Wizard Mode, please reer to page 28. For Expert Mode, please reerto page 34.

System Confguration Button

S ti C f ti


28/85



Wizard ModeWizard mode conguration is designed to allow a user to quickly set up a D-ViewCam system with ew simple clicks.This mode is recommended to quickly set up a working D-ViewCam system. You can use expert mode congurationto ne-tune the system at a later time. Click on the button o the wizard you wish to begin.

Add Camera WizardTo add a new IP camera, please reer to page 11.

System Backup Wizard

Add Camera Wizard Quick Settings Wizard

Exit

Expert Mode

Section Confguration


29/85




There are two system backup types, Video Recording Backup and System Database Backup. Click Next tocontinue.

Video Recording BackupThis unction saves video recording.

System Database BackupThis unction saves the congurationinormation.

Select a task and click Next to continue.



30/85



Video Recording Backup

Follow the steps below or Video Recording backup. Reer to page 45 to veriy that your video recording path iscorrect.

Select an IP camera rom the tree structure and selecta recording type. Click Next to continue.

Choose a start and end date and time. Click Next tocontinue.

Click Browse to select a directory to save the backuples.

You can make a new older by clicking Make NewFolder or you can select an existing older and clickOK to continue.



31/85



When the backup is complete, you can choose to keepthe source or Delete the source ater backup. Click Nextto continue.

Veriy that the inormation is correct and click Yes tostart the backup process.

When backup is complete, click OK to return to thesystem conguration screen.



32/85



System Database Backup

Follow the steps below or System Database backup.

Click Browse to select a directory to save the backuples. Click Next to continue.


When backup is complete, click OK to return to the

system conguration screen.



33/85



This setting will apply to all cameras. For user convenience, the system provides our dierent recording methods oruser to choose.

24/7 Continuous Recording - This setting will recordall IP cameras 24 hours a day and 7 days a weekcontinuously. Note:This recording arrangement willneed larger disk space.

24/7 Economic Recording - This setting will recordanytime when motion is detected. Note:This settingmay consume a large amount o your CPU resources.

Ofce Hours Only - The scheduled recording time isMonday through Friday rom 8:00 AM to 6:00 PM andwill start recording when motion is detected.

Non-Ofce Hours Only - The scheduled recording timeis Monday through Friday rom 6:00 PM to 8:00 AM andwill start recording when motion is detected.

Notes:

I these quick settings do not meet your recording schedule, you may set up a custom schedule or each IP camera.Please reer to page 60 or more inormation.

Excluding 24/7 Continuous Recording, other schedule recording types can be activated ONLY when the image motion

detection window is created on your cameras.

Quick Settings



34/85



Expert ModeExpert mode is similar to wizard mode. These two modes dier in the amount o available settings. Wizard mode oersminimal amount o settings while expert mode provides comprehensive options and settings that you can modiy. Toaccess Expert Mode, ollow the steps below:

Step 1

Move your mouse pointer to the bottom o the screen i the Setting and Search Area is hidden.

Step 2

The Setting and Search Area will appear automatically.

Step 3

Click the System Confguration button and select the Expert Mode button. The system will bring up the expertmode conguration panel.

System Confguration Button



35/85



Main Screen Interace

21

3

4

Expert mode is or more advanced use with comprehensive conguration options.

Follow these steps to congure Expert Mode.



36/85



Wizard

This wizard is the same as Wizard Mode (explained previously), which is designed to allow a user to quickly set up aD-ViewCam system with ew simple clicks. This wizard is recommended to quickly set up a working D-ViewCam system.Click on the button o the wizard you wish to begin.

Add Camera WizardTo add a new IP camera, please reer to page 11.


There are two system backup types, Video Recording Backup and System Database Backup. Click Next tocontinue.

Video Recording BackupThis unction saves video recording.

System Database BackupThis unction saves the congurationinormation.

Select a task and click Next to continue.



37/85



Video Recording Backup

Follow the steps below or Video Recording backup. Reer to page 45 to veriy that your video recording path iscorrect.

Select an IP camera rom the tree structure and selecta recording type. Click Next to continue.

Choose a start and end date and time. Click Next tocontinue.

Click Browse to select a directory to save the backuples.




38/85


g

When the backup is complete, you can choose to keepthe source or Delete the source ater backup. Click Nextto continue.

Veriy that the inormation is correct and click Yes tostart the backup process.

When backup is complete, click OK to return to thesystem conguration screen.



39/85


g

System Database Backup

Follow the steps below or System Database backup.

Click Browse to select a directory to save the backuples. Click Next to continue.


When backup is complete, click OK to return to the

system conguration screen.



40/85


g

Event Action

SystemIn system conguration, you can set the Event Action, Storage Setting, E-mail Server Setting and Database Backup.

Follow the ollowing steps to set event actions or Recording Path Error or Disk Full system events. For device eventactions, please reer to page 56.

Step 1

Select the Event Action rom the Node selection and preview area.

Step 2

Choose an event rom Add Event. The system will show the Event Action List Table window. For help with the settings,please reer to pages 42, 43, and 44.

Step 3

Ater you have nished setting the event action, the actions conguration will be displayed on the Action Table. Youcan use the Modiy or Remove button to modiy or remove the settings.



41/85


Step 1

Step 3

Step 2



42/85


Event Action List Table

Change Digital Output State

This setting will trigger the devices that connect to the system, such as alarm lights and sirens. When an event occurs,

you can change the device status (available or digital output only). Follow the steps below to congure the digital outputstate.

Step 1

Select the action Change Digital Output State and set the digital output.

Step 2

Change the output state to on or o.

Step 3

Seconds beore starting event action means the delayed time beore the event action is executed. I you preer NOTto start the event action immediately, you can set a wait time so that the action will start ater the wait time has expired.Click /OK to activate the setting.

Step 1Step 2

Step 3



43/85


Send E-mail

This setting will send email to the specied accounts indicating the type o event and attach an image taken while theevent occurred. Follow the steps below to congure Send Email.

Step 1Select the action Send Email and enter the email address. Check the Attach image i you want the system to send theimage(s) taken rom the selected IP camera.

Step 2

Seconds beore starting event action means the delayed time beore the event action is executed. I you preer NOTto start the event action immediately, you can set a wait time so that the action will start ater the wait time has expired.Click /OK to activate this setting.

Step 1

Step 2



44/85


Play Sound

This setting will play a sound or the specied accounts indicating the type o event when the event occurred. Followthe steps below to congure Play Sound.

Step 1Select the action Play Sound.

Step 2

You can select a sound rom the drop-down menu or you can select your own sound le by clicking the Browse buttonand choose a Wave le (.wav). You can test the sound le by clicking the Play Sound button.

Step 3

Seconds beore starting event action means the delayed time beore the event action is executed. I you preer NOTto start the event action immediately, you can set a wait time so that the action will start ater the wait time has expired.Click /OK to activate the setting.

Step 1

Step 2

Step 3



45/85


Basic Setting

Step 1 - Select Basic Setting rom the tree menu.

Step 2 - Assign recording paths or schedule recording, event recording, manual recording, snapshot recording and

backup.

Step 3 - You can change the system language to English, Chinese Traditional or Chinese Simplied.

Step 4 - Enable or Disable the event action unction. Click Save to save your settings.

The system will detect whether the assigned recording path exists. I not, the system will inorm you to change it to anappropriate path. Please ollow the instructions below.

Step 1

Step 2

Step 3 Step 4

RecycleThe system will automaticallydelete out-dated data toreclaim storage space. Youcan choose the recycle unit(in GB or days).

Available Space (GB)The system will countand display the availablespace o your disk in thistext box.



46/85


Email Server Setting

This unction is used to congure your email sever settings that will be used to send event notications.

Step 1 - Select Email Server Setting rom the tree menu.

Step 2 - Input the email server inormation.

Step 3 - Click the Test button to test the setting. An email will be sent using the current setting. Then click Save to activatethis setup.

Server Name/IP:

Username:

Password:

Send From:

Message Subject:

Input your email server name o your email provider. Example: mail.test.com or an IP address,such as 192.168.1.1.

Input your email account username.

Input your email account password.

Insert sender email address. Example: [email protected]

Insert a subject or your email message. This message will send to your email once an eventis detected. Example: An alarm occurs in the kitchen.

Step 1

Step 3

Step 2



47/85


Database Backup

The database backup unction saves all system settings and event log. You can set a time when the system will executea database backup automatically on daily basis. Follow the steps below.

Step 1 - Select Database Backup rom the tree menu.

Step 2 - You can click Import to restore predened system settings, or Export to save or backup your current settingor uture use.

Step 3 - Set a time on daily basis when system will backup the system data using the drop-down menu. Click Save toactivate this setup.

Step 1

Step 3

Step 2



48/85


UserD-ViewCam provides 5 user accounts, 1 administrator account and 4 normal user accounts.

AdministratorOnly an administrator can modiy these settings. Follow the steps below to set up an administrators account.

Step 1 - Select Administrator rom the tree structured menu.

Step 2 - You can click the Browse button to upload a picture or the administrator.

Step 3 - Enter the users Basic Inormation. You can also always change the inormation. Then click Save to activatethis setup.

Step 1

Step 3

Step 2



49/85


Normal User

The administrator may manage up to 4 normal user accounts. You can modiy or remove all these accounts but cannot add more than 4 accounts. To modiy the user(s) accounts, ollow the steps below.

Step 1 - Select User1 rom the tree structured menu.

Step 2 - You can upload a picture or the user. Enter or modiy users Basic Inormation, and privilege setting here.A normal user can be administrator i he/ she receives administrators privilege. You can adjust this users validtime. Then, click Save to activate this setup.

Step 1

Step 3

Step 2



50/85


My Map

My Map is the deault map or the system. You can build your own map(s) by adding it into My Map, and assign it toyour device(s). Follow below steps to add a map.

Add a MapStep 1 - Click the /Add Map button.

Step 2 - Input a map name or browse to locate the desired map lename.

Step 3 - Select an image le and click Open.

Step 4 - Click /OK to save the setting. The new map will be added to the tree menu on the let.

Step 4

Step 3

Step 2



51/85


Modiy Map

Step 1 - Click the /Add Map button

Step 2 - Click Browse to locate the desired image le or input the image lename directly.

Step 3 - Select an image le and click Open.

Step 4 - Click /OK to save the setting. The modied map will be updated to the tree menu on the let.

Step 4

Step 3

Step 2



52/85


Placing Device to eMap

Step 1 - Select the My Map icon at the Node Selection and Preview Area. The selected eMap will be displayed in theMap Display area.

Step 2 - Drag the device icon (o the selected camera) rom Node Selection and Preview Area, and then drop it onto theeMap Display Area. Right click the device icon, a pop-up window will indicate the direction where IP camera isacing (you can also select the direction in the window to control your camera).

Note:All devices can be deleted by right clicking the device icon in the eMap interace and click theDeletebutton.

Step 1

Step 2

Pointer Deault Scale

Move

Area Zoom

Center Zoom Out

Center Zoom In



53/85


Inormation

Device setting can be congured in Expert Mode. I the device is disconnected, the device settings such as preset,motion detection, and image quality will be disabled. The ollowing section will explain the details o device setting.

Camera InormationYou can change the Camera Name, ID andPassword. The system will automatically loadthe Model Name, IP address, Device Port, Macaddress and Status inormation. You cannotmodiy this inormation.

Select OrientationI the camera is installedupside down, use the settingo Vertical Flipped to lipthe image upside down, or

mirror the image to fip it tothe let, right or both.

Networking InormationYou can change both IP address andport number. The system will loadStatus inormation automatically andyou cannot modiy this inormation.

AudioChoose to Enable or Disablethe two way audio unction.

Sensor / RelayYou can change the sensoror relay name here.

Device Setting



54/85


Preset Point

Preset Location species where the IP camera should point. Preset Name species the position name o the pointer.Follow the step below to set the Preset Point.

Step 1 - Use the PT Control interace to adjust the direction o IP camera. Choose a number in Preset Location eld,

and enter a name or this pointer in Preset Name text box.

Step 2 - Click Save and the newly added preset name will show up in the Preset Location eld (you can also add otherpreset points in the same way).

Note:To remove a preset, select the Preset Location and clickRemove.

Auto Scan PeriodThe IP camera will auto pan and autopatrol within this time interval. Youmay get service o Periodically Auto

Pan and Periodically Auto Patrol byassigned interval, but this servicewill stop the alarm service o that IPcamera, including Event Action oGo Preset.



55/85


Motion Detection

To detect specic area motion detection, you have to dene at least one detection zone. Follow the steps below.

Step 1 - Click New button and a small window will appear on the screen, you can drag the mouse to draw a detectionzone. You may dene more than one zone on the screen by repeating the same process.

Step 2 - Adjust the window to dene the detection zone.

Step 3 - Input a window name, then click the Save button.

Enable Motion DetectionCheck the box to activate.

Window NameGive the detection zone a

name.

SensitivityModiy the sensitivity setting bychanging the slider control. Movetoward right will increase the sensitivitylevel, which means a relatively smallmovement will trigger an action.Move the slider control toward let willreduce the sensitivity or movementdetection.

PercentageModiy the percentage setting bychanging the slider control.

NewCreate a new window.

SaveSave the settings.



56/85


Event Actions

These event actions are more related to the device events, such as Image Motion Detected, Sensor Alarm Detected,and Video Lost. For system event action setting, please reer to page 40. Follow the steps below.

Step 1 - Select the Device Icon rom the Node selection and preview area.

Step 2 - Choose an event rom Add Event. The system will show Set Event Action window. For help with the settings,please may reer to pages 42, 43, 44, 57, 58 and 59.

Step 3 - Ater nished setting the Event Action, the actions conguration will show on the Action Table. You can usethe Modiy and Remove buttons to modiy or remove the settings.

Note: Accept next event after (seconds) means the time interval between the frst event and next event that can beprocessed. Any event(s) occurs during the interval will be ignored.

Step 1

Step 3

Step 2



57/85


Event Action List Table

Show Live Video

Follow the steps below to show live video.

Step 1 - Select Show Live Video action.

Step 2 - Select a video source. Then, Click /OK to activate this setup.

1. I only one event is triggered, the camera images will be displayed on the 4 split screens and it is arranged startingrom up-let to up-right, low-let, and low-right.

2. I multiple events are triggered, live video will be displayed accordingly. I more than 4 cameras are triggered, thelive video will be displayed rotational.

Note:Seconds beore starting event action means the delayed time beore execute the event action. I you preer NOT tostart the event action immediately, you can set a wait time so that the action will start ater the wait time has expired.

Step 1 Step 2



58/85


Start Recording

The event recording o breached camera; event recording time is set by number o seconds.

Step 1 - Select Start Recording Action.

Step 2 - Select a video source. Click /OK to activate this setup.

Note:Seconds beore starting event action means the delayed time beore execute the event action. I you preerNOT to start the event action immediately, you can set a wait time so that the action will start ater the wait time hasexpired.

Step 1Step 2



59/85


Go to Preset Point

Turn to the preset location upon the motion triggering.

Step 1 - Select Go to Preset Point action.

Step 2 - Select rom the Preset Point eld. When event is detected, the system will turn PT camera to the speciedpreset location. Then, click /OK to activate this setup.

Note:Seconds beore starting event action means the delayed time beore execute the event action. I you preer NOT tostart the event action immediately, you can set a wait time so that the action will start ater the wait time has expired.

Step 1

Step 2



60/85


Schedule / Recording (Settings)

Recording RateSet the recording rame rate,in rames per second (FPS).

Event Recording LengthDene the time length o event recordingor pre-event and post-event.


S h d l / R di (S h d l )


61/85


Schedule / Recording (Schedule)

Follow the steps below to set the schedule.

Step 1 - Select Set Scheduled Recording to schedule recording, or select Set Scheduled Event to schedule eventrecording.

Set Scheduled Recording

The system provides our Scheduled Recording types:

Disable: No video will be recorded or this schedule.

24/7: Video will always be recorded.

Select: Video will be recorded according to your schedule.

Economic: Video will only be recorded when motion is detected.

Set Scheduled Event Setting

Disable: When an event occurs, no video will be recorded.

24/7: When an event occurs, the video will always be recorded.

Select: When an event occurs, the video will be recorded according to your schedule.

Step 2 - Select the time or period when you want to schedule the recording. The activated block will be colored. To cancelor modiy a schedule setting, click the colored block to deactivate it.



62/85


TemplatesProvides a list o availabletemplates or you to chooseand apply. You must add/set atemplate rst beore apply it toother devices.

Add TemplateYou can add and save yoursetting or the scheduledrecording into a template.

Apply TemplateYou can select an available template

rom the drop-down menu and thenclick Apply. This will save some eortsin scheduling the recording.



63/85


Schedule / Recording (Specifc Date)

Follow the steps below to set a specic date.

Step 1 - Select the start date and end date.

Step 2 - Put a remark or the specic date.Step 3 - Click Add to add your specic date to the table on the right.

Step 4 - I you want to modiy the specic date, click a specic date rom the table, then modiy the date and remarks,and click Modiy.

Step 5 - Click Import/Export button to load or output the specic date.

Step 6 - Select a specic date and click Remove to delete the specic date.

DateSelect the specic date period.

RemarksYou can put a remark to describethe specic date.

AddClick Add to add a specicdate.

ModiyYou can modiy the specic date byselecting a specic date and clickModiy button.

ImportClick Import to import rom atext le.

ExportClick Export to save your current

setting into a text le or uture useor backup.

RemoveRemove the specic date.



64/85


Image Quality

Below is a description o the Image Quality screen.

ContrastAdjust the contrast between-5 and +5.

BrightnessAdjust the br ightnessbetween -5 and +5

HueAdjust the hue between -5and +5.

SaturationAdjust the saturation between-5 and +5.

DeaultClick the Deault button to

preset all the setting to deaultvalues.



65/85


Playback

Video Search and Playback Management

The Video search and playbackbutton allows you to playback recorded video through the schedule recording, eventrecording, manual recording, or all. This unction also provides additional eatures or exporting video les into AVIormat. The playback speed can be specied with the control bar. Follow the steps below.

Step 1 - Select the video type, start and end date.

Step 2 -Select the device type, and then click Query.

Step 3 - Double click the le you want to playback rom the result list.

Step 4 - You can backup the video les by clicking the Backup button.

Step 5 - You can use the buttons in the Playback Control area to playback the video. The system allows you to rewind,ast backward, stop/pause, ast-orward, snapshot an image, and play the video in ull screen mode by clickingthe Switch to ull mode button (you may click the Switch to deault mode to go back to video search and

playback page.)

Step 6 - Click /Close button to return to the main screen.


St 2


66/85


Step 2

Step 3

Step 4

Step 5

Step 6

Step 1

Switch to Full Mode

Fast orward

Cue In

Cue Out Convert AVI

View Result

Rewind

SnapshotFast Forward

Pause Play



67/85


Type o VideoThe system provides three typeso video, schedule recording, event

recording and manual recording.

From, ToYou can assign the system toquery particular date.

Select DeviceThe system lists all the devicesattached on your system.

Result ListA query result will appear in thespreadsheet. You can assign thesystem to print out how manyrecords in a page and use thepaging button to navigate thepage o the spreadsheet.

List View / Thumbnail ViewSwitch the result list to list viewor thumbnail view.

Video File BackupYou can backup a video, backup thendelete or delete without backup.

HistogramThe red mark in the Histogramarea helps you quickly locatethe moment o motion video ithe motion detection is setup.The histogram can be partiallyenlarged by dragging the mouseto show details.

Playback ControlYou can use the button inthe control area to operatethe video.

Video ExportExport the video les in AVIormat.


S


68/85


Event Search and Playback ManagementThe Event search and playbackbutton allows you to select and query both the event(s) and camera(s), and playbackthe event(s) which has been recorded by the system. This unction also provides additional eatures or you exportingvideo les in AVI ormat, and exporting the event log inormation (Date/Time, Source, Type, Action, Relation Source

and Context inormation) in .txt le. The playback speed can be specied with the playback control bar.

Step 1 - Select the event type, start and end date.

Step 2 - Select device type, and then click Query.

Step 3 - I the result list has a recording le, double click the list, then the system will pop up a video display page andplayback the video. Click Close button to return to event search and playback page.

Step 4 - You can export the log lists by clicking the Export button.

Step 5 - Click /Close button to return to main screen.



69/85


From, ToYou can schedule the systemto query event.

Log ListList the unusual event historythat had been detected by thesystem.

Select DeviceThe system lists all the devicesattached on your system.

Export

Export the event log inormationin .txt le.

Step 2

Step 3

Step 4

Step 5

Step 1

Type o EventThe system provides several typeso device event, and each device hasdierent event action(s).

Section - Troubleshooting

F tl A k d Q ti


70/85


1. What is the dierence between D-Link D-ViewCam and the traditional surveillance system?

D-Link D-ViewCam records video in MJPEG and MPEG4 ormats, stores high quality image data on computer harddisks, and provides easy query and review o the stored video. Traditional surveillance systems use videotape orstorage and review, which is hard to managed, time consuming and the recorded video will degrade over a period otime or usage.

2. Why use the D-Link D-ViewCam Intelligent Solution?D-Link D-ViewCam is the bundled video surveillance system sotware that provides advanced security monitoringand device management unctions to use with D-Link Internet cameras. This sotware uses IP technology to providecomprehensive management unctions such as system controls, live video eeds and archived recordings.

3. We have security guards on duty 24 hours a day, 7 days a week. Do we still need D-Link D-ViewCam?Security guards and camera surveillance systems can complement each other. Your security guards can catch thievesred-handed but not in other circumstances, such as i they are preoccupied with another task. D-Links D-ViewCamcan always automatically record events or review or to be used as evidence. Your surveillance cameras can connectto any I/O devices, and D-ViewCam can discreetly and timely alert your security guards o inadvertent events, allowingthem to react to the situation in an eective manner.

4. What kind o network does D-Link D-ViewCam run on?D-Link D-ViewCam runs on standard TCP/IP networks, such as a local area network (LAN), and over the Internet. Iusing Internet, a broadband DSL or cable modem connection is recommended to ensure good quality o video imageis being transerred over the Internet.

Frequently Asked Questions

D-Link D-ViewCam Features


5 How are multiple camera views displayed on the screen?


71/85


5. How are multiple camera views displayed on the screen?I you deploy several cameras and they are all displaying video at the same time, you have several options to arrangethe display o these videos on your computer screen. One option is to reserve a major part o the screen to displaythe video rom a single camera. Another option is to split the screen to show videos rom multiple cameras. To switchthe display rom one camera to another, you can either manually select a camera, or have the system automaticallydisplay videos rom all cameras in turn, called auto rotation.

6. Does D-Link D-ViewCam support cameras that have motion detection capability?Yes. I the camera has motion detection unction, D-ViewCam will take advantage o that. When the camera doesnot have motion detection capability, D-ViewCam will perorm sotware motion detection or it, at the cost o systemperormance.

7. How do I estimate an adequate disk space to store the recorded video?The Disk Space required can be calculated with these two ormulas:

1. For MJPEG cameras: Frame Size x Frame per Second x Total Second, or2. For MPEG4 cameras: Bit rate / 8 x Total second.For example:MJPEG cameras: Recording at medium quality CIF (10 Kbytes/rame) at 30 FPS or a week requires 173G Bytes/cameraMPEG4 cameras: Recording with bit rate at 64kbps (low quality CIF) or a week = 4.6 G Bytes/cameraNote:The data revealed here is only or reerence. The real recording capacity depends on the view andenvironment.

8. Do I need a very powerul computer to run D-Link D-ViewCam?Please reer to the System Requirements table on page 4. To monitor more than 16 cameras simultaneously, thequality o the live video display may depend on your hardware specication.

Note:I a mega pixel camera is used with the D-ViewCam application, the minimum system requirement should be

raised to CPU: Intel P-4 3.4GhZ or above with 1GB o memory due to the resources required to process and store

large amounts o image data.


9 Please describe the privilege based access o D Link D ViewCam


72/85


9. Please describe the privilege-based access o D-Link D-ViewCam.D-Link D-ViewCam uses a simple privilege control scheme to let users access the system and use dierent unctions.A user can have administration privilege or normal user privilege.

10. Windows Vista operation systems user control eature may interere with the normal operation o theD-ViewCam application.

For Windows Vista users: please go to User Accounts and Family Saety > User Accounts > Turn User AccountControl on or o, then uncheck the Use User Account Control (UAC) to help protect your computer checkbox.Restart your computer to validate the setting.

For additional inormation o User Account Control, please go tohttp://www.microsot.com/windows/products/windowsvista/eatures/details/useraccountcontrol.mspx.


D Li k D Vi C O ti


73/85


1. How are video images stored?Video images are compressed into MJPEG or MPEG4 ormat, and then stored on your computer hard disk or a

designated network storage device.

2. What rame sizes does D-Link D-ViewCam use?For MJPEG, each rame is approximately 14 to 15KB each. However, it also depends on your cameras specicationsand setting.

3. What should I do when saving image confguration or image quality and the system pops up Parametersetup error message?One o the ollowing might cause this problem:1. Camera is disconnected.2. Network is unstable.3. Firewall.I you install D-ViewCam on a PC with rewall sotware running, the rewall sotware may reject some Internet packets,which are considered insecure. You need to turn o Internet Security or disable Personal Firewall in order to saveimage congure/ image quality o your camera. Remember to turn on Internet Security or enable Personal Firewalllater to secure your system.

4. Can we change the FPS (rame per second) rate o a camera?FPS is the number o image rames that a camera shoots in a video operation. For MJPEG le, you can set the FPSrate according to your requirement.Note:Not all setting o your camera is available in D-ViewCam. The FPS rate that you set cannot exceed the maximumFPS rate o your camera. For MPEG4 ormat, you can change bit rate instead o FPS. Please make detail confgurationson cameras web interace.

D-Link D-ViewCam OperationVideo Image Confguration


5 Which ormat could my recorded video fle covert into?


74/85


5. Which ormat could my recorded video fle covert into?D-Link D-ViewCam can convert the recorded video into AVI ormat with the available codec in your operatingsystem.

Video Display

6. What should I do i there is no video display o the camera ater I have just added it to D-ViewCam?Please check to see i you correctly typed in the IP address o the camera. I you changed the deault user name andpassword o the camera, you must input that inormation in D-ViewCam in Expert mode. The changed value will takeeect ater you re-login to D-ViewCam. Please reer to page 53 or changing the camera ID and Password.

7. Why isnt video displayed rom the connected camera(s)?The possible root causes:

1. The network is unstable2. The workload is too heavy or your computer to handle.

8. How do I record video in D-ViewCam?D-Link D-ViewCam provides our dierent recording methods:1. Manual recording (capture o video eed at the moment you command the system to).2. Schedule recording (automatic recording according to the time periods that you set).3. Event recording (automatic recording according to the event settings).

4. Motion detection recording in scheduled time (In the time periods you set, start recording only when motion isdetected. This can make disk usage more economical)

Appendix A - Wireless Basics

Firewall


75/85


Firewall

9. What about frewalls? Do they aect D-Link D-ViewCam?I you use D-Link D-ViewCam on computers with Windows XP SP2 or any other applications with personal rewalls,please congure the rewall to allow D-Link D-ViewCam to pass through. Most the personal rewalls will automatically

prompt you to permit D-ViewCam program to be used in the network.

10. What about frewalls like Nod 32 which has to be manually input to permit D-ViewCam installation?I you use D-Link D-ViewCam on computers with Nod32 personal rewall, please congure the rewall manually ateryou have installed D-ViewCam as ollowing steps:

Click NOD32 antivirus system icon on the task bar to open it.

Select IMON > Setup > Miscellaneous > Exclusion > Edit > Addto C:\Program Files\D-Link D-ViewCam\Exes\Admin.exe, Control.exe, Monitor.exe, and VideoProxy.exe to the Exclude applicationswindow.

Note:Paths depend on your sotware installation.


Click OK to exit Exclude applications window


76/85


Click OK to exit Exclude applications window.

Click OK to exit IMON Setup window.

Click Quit to unload IMON.

Click Start to load IMON

Event

11. How does the event management operate?D-Link D-ViewCam can receive input rom Motion Detection or Sensor (DI, or Device Input) to create an event. Then,the event can be used to trigger DO (Device Output), video recording, show live video, e-mail notication, play sound,and go to preset point (on cameras with Pan and Tilt unctions).

12. How does event recording work?It starts recording automatically according to your event settings.

13. In what ormat can I export the event report to?D-ViewCam can export the event report in text ormat. Note that Microsot Word 2000 is currently not supported.

14. When an event occurs, how do I know which camera it comes rom?Please look at the Event Notication Log in the main screen. The source column shows the event source.


15 How do I get event notifcations?


77/85


15. How do I get event notifcations?D-Link D-ViewCam sends event messages in dierent ways, based on the event action setting o a camera. Forexample, i the event action is Email, the message will be sent by Email. For details, please reer to Users Manual oD-ViewCam

16. Ater Ive changed the time or date o my computer system, the D-Link D-ViewCam event unction does

not seem to work anymore?Please exit D-ViewCam then reboot your computer ater youve changed your computer systems time and date. Thenrun D-ViewCam again. The event unction should go back to normal.

Database

17. Whats the purpose o database backup?The conguration data, operating parameters and log data o D-ViewCam are stored in database. D-Link D-ViewCamcan backup database periodically and automatically. So, you can restore it i the system is corrupted inadvertently.

18. What is the purpose o database restore unction in D-Link D-ViewCam?The database restore unction is provided to saeguard your D-ViewCam program database in case i it is corruptedinadvertently. D-ViewCam can backup the database automatically but you have to restore the database manually.For details, please reer to D-ViewCam Users Manual.

Save and Copy to Setting19. Why do we need to use Save Setting and Copy to unctions in D-Link D-ViewCam?These two unctions are designed to let users congure cameras eciently. Camera congurations such as: Areasetting, map le, device ratio, congurations in Camera Setting, Image Alarm Setting, Preset, eMap location andsensor alarm setting can all be saved and copy to another camera. However, please remember to review the settingso the target camera ater copy to to make sure all settings are correct and work as intended.


Storage Space Setting


78/85


Storage Space Setting

20. What will happen when my hard disk or network storage device is running out o space?When your hard disk or network storage device is approaching 90% ull, and i you have enabled the Recycle unction,the system will automatically start to delete the oldest recorded video on your hard disk or network storage to makespace or the new les.To prevent losing recorded video data, please remember to periodically back up your recorded video les and deletethe unwanted ones.For details on how to use this unction, please reer to page 36.

Contacting Technical Support


79/85

Contacting Technical SupportU.S. and Canadian customers can contact D-Link technical support through our web site or by phone.

Beore you contact technical support, please have the ollowing ready:

Model number o the product Hardware Revision (located on the label on the bottom o the unit (e.g. rev A1)) Serial Number (s/n number located on the label on the bottom o the unit).

Please check the D-Link support site below or the latest product inormation including FAQs, known issues, and otherproduct-related updates.

For customers within the United States:

Phone Support:(877) 354-6555

Internet Support:http://support.dlink.com

For customers within Canada:

Phone Support:(800) 361-5265

Internet Support:

http://support.dlink.com

Appendix E - Warranty

Warranty


80/85


WarrantySubject to the terms and conditions set orth herein, D-Link Systems, Inc. (D-Link) provides this Limited Warranty:

Only to the person or entity that originally purchased the product rom D-Link or its authorized reseller or distributor, and Only or products purchased and delivered within the ty states o the United States, the District o Columbia, U.S. Possessionsor Protectorates, U.S. Military Installations, or addresses with an APO or FPO.

Limited Warranty:D-Link warrants that the hardware portion o the D-Link product described below (Hardware) will be ree rom material deects inworkmanship and materials under normal use rom the date o original retail purchase o the product, or the period set orth below(Warranty Period), except as otherwise stated herein.

Hardware (excluding power supplies and ans): One (1) year Power supplies and ans: One (1) year

Spare parts and spare kits: Ninety (90) days

The customers sole and exclusive remedy and the entire liability o D-Link and its suppliers under this Limited Warranty will be, atD-Links option, to repair or replace the deective Hardware during the Warranty Period at no charge to the original owner or to reund theactual purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Oce. The replacementhardware need not be new or have an identical make, model or part. D-Link may, at its option, replace the deective Hardware or any partthereo with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respectsto the deective Hardware. Repaired or replacement hardware will be warranted or the remainder o the original Warranty Period or ninety(90) days, whichever is longer, and is subject to the same limitations and exclusions. I a material deect is incapable o correction, or iD-Link determines that it is not practical to repair or replace the deective Hardware, the actual price paid by the original purchaser or the

deective Hardware will be reunded by D-Link upon return to D-Link o the deective Hardware. All Hardware or part thereo that is replacedby D-Link, or or which the purchase price is reunded, shall become the property o D-Link upon replacement or reund.


Limited Sotware Warranty:


81/85


D-Link warrants that the sotware portion o the product (Sotware) will substantially conorm to D-Links then current unctional specicationsor the Sotware, as set orth in the applicable documentation, rom the date o original retail purchase o the Sotware or a period o ninety(90) days (Sotware Warranty Period), provided that the Sotware is properly installed on approved hardware and operated as contemplatedin its documentation. D-Link urther warrants that, during the Sotware Warranty Period, the magnetic media on which D-Link delivers theSotware will be ree o physical deects. The customers sole and exclusive remedy and the entire liability o D-Link and its suppliers underthis Limited Warranty will be, at D-Links option, to replace the non-conorming Sotware (or deective media) with sotware that substantially

conorms to D-Links unctional specications or the Sotware or to reund the portion o the actual purchase price paid that is attributableto the Sotware. Except as otherwise agreed by DLink in writing, the replacement Sotware is provided only to the original licensee, andis subject to the terms and conditions o the license granted by D-Link or the Sotware. Replacement Sotware will be warranted or theremainder o the original Warranty Period and is subject to the same limitations and exclusions. I a material non-conormance is incapableo correction, or i D-Link determines in its sole discretion that it is not practical to replace the non-conorming Sotware, the price paid bythe original licensee or the non-conorming Sotware will be reunded by D-Link; provided that the non-conorming Sotware (and all copiesthereo) is rst returned to D-Link. The license granted respecting any Sotware or which a reund is given automatically terminates.

Non-Applicability o Warranty:The Limited Warranty provided hereunder or Hardware and Sotware portions o D-Links products will not be applied to and does not coverany reurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, thesellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being soldAs-Is without any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anythingstated herein to the contrary.

Submitting A Claim:The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expiredand the product is within warranty, the customer shall submit a claim to D-Link as outlined below:

The customer must submit with the product as part o the claim a written description o the Hardware deect or Sotwarenonconormance in sucient detail to allow DLink to conrm the same, along with proo o purchase o the product (such

as a copy o the dated purchase invoice or the product) i the product is not registered.

The customer must obtain a Case ID Number rom D-Link Technical Support at 1-877-453-5465, who will attempt to assistthe customer in resolving any suspected deects with the product. I the product is considered deective, the customer mustobtain a Return Material Authorization (RMA) number by completing the RMA orm and entering the assigned Case IDNumber at https://rma.dlink.com/.


Ater an RMA number is issued the deective product must be packaged securely in the original or other suitable shipping


82/85


Ater an RMA number is issued, the deective product must be packaged securely in the original or other suitable shippingpackage to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outsideo the package. Do not include any manuals or accessories in the shipping package. DLink will only replace the deectiveportion o the product and will not ship back any accessories.

The customer is responsible or all in-bound shipping charges to D-Link. No Cash on Delivery (COD) is allowed. Productssent COD will either be rejected by D-Link or become the property o D-Link. Products shall be ully insured by the customer

and shipped to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsibleor any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer viaUPS Ground or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link i you use anaddress in the United States, otherwise we will ship the product to you reight collect. Expedited shipping is available uponrequest and provided shipping charges are prepaid by the customer. D-Link may reject or return any product that is notpackaged and shipped in strict compliance with the oregoing requirements, or or which an RMA number is not visible romthe outside o the package. The product owner agrees to pay D-Links reasonable handling and return shipping chargesor any product that is not packaged and shipped in accordance with the oregoing requirements, or that is determined byD-Link not to be deective or non-conorming.

What Is Not Covered:The Limited Warranty provided herein by D-Link does not cover:Products that, in D-Links judgment, have been subjected to abuse, accident, alteration, modication, tampering, negligence, misuse, aultyinstallation, lack o reasonable care, repair or service in any way that is not contemplated in the documentation or the product, or i themodel or serial number has been altered, tampered with, deaced or removed; Initial installation, installation and removal o the product orrepair, and shipping costs; Operational adjustments covered in the operating manual or the product, and normal maintenance; Damagethat occurs in shipment, due to act o God, ailures due to power surge, and cosmetic damage; Any hardware, sotware, rmware or otherproducts or services provided by anyone other than D-Link; and Products that have been purchased rom inventory clearance or liquidationsales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product.

While necessary maintenance or repairs on your Product can be perormed by any company, we recommend that you use only an AuthorizedD-Link Service Oce. Improper or incorrectly perormed maintenance or repair voids this Limited Warranty.

Disclaimer o Other Warranties:EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED AS-IS WITHOUT ANY WARRANTYOF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR APARTICULAR PURPOSE AND NONINFRINGEMENT.


IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF


83/85


SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY,SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.

Limitation o Liability:TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY

OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANYCHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FORLOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OFOTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINKS PRODUCT IS CONNECTED WITH, LOSS OF INFORMATIONOR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE)RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OFTHIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDYFOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE ORNONCONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE

PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIESARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY.

Governing Law:This Limited Warranty shall be governed by the laws o the State o Caliornia. Some states do not allow exclusion or limitation o incidentalor consequential damages, or limitations on how long an implied warranty lasts, so the oregoing limitations and exclusions may not apply.This Limited Warranty provides specic legal rights and you may also have other rights which vary rom state to state.

Trademarks:D-Link is a registered trademark o D-Link Systems, Inc. Other trademarks or registered trademarks are the property o their respective

owners.

Copyright Statement:No part o this publication or documentation accompanying this product may be reproduced in any orm or by any means or used to makeany derivative such as translation, transormation, or adaptation without permission rom D-Link Corporation/D-Link Systems, Inc., asstipulated by the United States Copyright Act o 1976 and any amendments thereto. Contents are subject to change without prior notice.

Copyright 2008 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.


CE Mark Warning:


84/85


gThis is a Class B product. In a domestic environment, this product may cause radio intererence, in which case the user may be requiredto take adequate measures.

FCC Statement:This equipment has been tested and ound to comply with the limits or a Class B digital device, pursuant to part 15 o the FCC Rules.These limits are designed to provide reasonable protection against harmul intererence in a residential installation. This equipmentgenerates, uses, and can radiate radio requency energy and, i not installed and used in accordance with the instructions, may causeharmul intererence to radio communication. However, there is no guarantee that intererence will not occur in a particular installation. Ithis equipment does cause harmul intererence to radio or television reception, which can be determined by turning the equipment oand on, the user is encouraged to try to correct the intererence by one or more o the ollowing measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent rom that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician or help.

For detailed warranty inormation applicable to products purchased outside the United States, please contact the corresponding localD-Link oce.

Registration


85/85

Version 1.0

Product registration is entirely voluntary and ailure to complete or return this orm will not diminish your warrantyrights.

Registration

dcs910 dviewcam manual en us

Documents