Decking ProductQUICK INSTALLATION GUIDE

For more information, contact us at: Allura USA / 844-4ALLURA (844.425.5872) / www.AlluraUSA.com

Allura™ shall be carried on a flatbead protected from moisture.

A TRANSPORTATION

C CORRECT HANDLING

D FASTENING

E INSTALLATION INSTRUCTIONS

Each Allura™ board shall be horizontally carried by two people or one person can carry the pieces of Allura™ board by holding them by the middle part of their narrow edge. Protect the edges and corners to prevent them from damage.

Drill-tip stainless steel deck screw #7x1-5/8” (metal). Face fastening.

Sharp-tip deck screw 9X2-1/2” (wood).Face fastening.

TOOLS TO BE USED

COMPRESSED -AIR NAILER

HAMMER

SCREWDRIVER

Stainless steel 2.5” nail (minimum). Face nailing.

Grooved Mantis™ Clip # 396.Blind fastening is recommended.Other similar hidden fastners can be used.

TAPE MEASURE

CIRCULAR SAW WITH CARBIDE OR NOTCH DISC

Phil l ips tip

Torx tip

Square tip

B STORAGE• Keep material flat and off the ground on stringers or platforms.

• If covered area is not available at the site, place skids on proper blocking to allow airflow underneath and shelter with waterproof covering.

V. 02-16

Allura™ Decking can be installed on metal or wood joist, located 16 inches on centers.

F LOADS INFORMATION

G DECKING DIMENSIONS

H FRAMING AND FACE FASTENING

1-1/4”

1”

Allura™Fastening

DETAIL 1 DETAIL 2

DECK BOARD

7-1/4”

6”

11-1/4”

11/16”

7-1/4”

6”

11-1/4”

11/16”

7 1/4”

6”

11 1/4”

1”

1”

FasteningAllura™

Joint

Allura™

Detail 1

Detail 2

16” maximum

WIDTH (in) LENGTH (ft) WEIGHT (PLF) AREA (SF)DECK BOARD 6 12 3.3 6

7-1/4 12 4 7.2511-1/4 12 4.33 11.25

FASCIA BOARD

DIMENSION TABLE

Allowable uniformly distributed load (PSF)*

409

Point Load (Pounds)* 167* Considering joist span=16"

1/4”6”1-1/4”

1/4”6”

FASCIA BOARD

Decking ProductQUICK INSTALLATION GUIDE

For more information, contact us at: Allura USA / 844-4ALLURA (844.425.5872) / www.AlluraUSA.com

Allura™ Fiber Cement Decking should be treated with a protective finish every few years, which will keep the surface attractive and protect from all the effects of elements and climate.

Water-based waterproofing sealers and cement finishes penetrate the cement, carrying silicone or wax additives that keep deck from absorbing water. Most sealers contain mildewcides and UV inhibitors for added protection. You will need to reapply a sealer every year or two to maintain UV protection.

Restore an older, weathered deck to its original color and luster with a deck-brightening product. Brighteners are available at most hardware stores and home centers.

J BEST PRACTICE TIPS

K HIDDEN FASTENING

I FASCIA BOARD INSTALLATION

L FINISHING

M MAINTENANCE OF DECKINGAll fiber cement, composite or, wood decking should be regularly and thoroughly cleaned.

All decks even low maintenance decks require regular cleaning to keep looking and performing well. Depending on the amount of dirt and leaves in your area you may need to clean the deck more frequently. Sweep your deck removing all loose dirt and leaves. Use a leaf blower or equal.

Rinse the deck off using a garden hose or pressure washer. When using a pressure washer be sure to raise the nozzle a few feet off the deck to prevent damaging the fiber cement.

If the decking´s current finish has faded or the fiber cement has algae or mildew growth, use a deck cleaner to remove the stubborn stains. Deck cleaner will remove general dirt and grime as well as grease spots left by grilling. If the deck is just dirty but not weathered, try using a diluted solution of ordinary dish soap, followed by a good scrubbing. Soap may be all the cleaning agent your deck really needs.

If a stain persists, repeat the process as necessary.

Inspect your deck at least once a year, more often if the weather over any given season is especially severe. Replace loose or rusting hardware or fasteners as soon as you detect them to prevent future problems.

Apply a new coat of sealant as necessary, according to the requirements of material used on your deck.

Carefully inspect the deck surface, railings and structure for signs of damage. Replace or reinforce damaged wood or metal as soon as possible. Replace damaged decking if it is split or otherwise compromised.

V. 02-16

Step 1 Step 2

Step 3

Wood screw 2-1/2”

Wood joist

1”

Metal deck screw 7x1-5/8’’

Metal joist

Allura™

Allura™

1”

BUTT JOINTS: USING ADDITIONAL WOOD PIECES

1) IT IS RECCOMENDED TO PRE-DRILL THE BOARD. Pre Drill pilot holes or use self-tapping deck screws.

2) USING CLIPPED HEAD NAIL GUNClipped head nail 2” min. Allura™

Structural Wood piece

1”

Wood screw 2-1/2”

1”

Allura™

Additional Wood joistBlock nailer

Wood screw

Wood joist

Allura™Wood screw

Additional wood piece

Wood joist

Allura™

Allura™

Allura™

Grooved Mantis™ clip

Grooved Mantis™

clip

Wood Joist

Wood Joist

Note: Mantis™ clip part number 396

Allura™ Decking

Fascia Board

Allura™ Decking

Fascia Board