denon avr-2112ci eng manual

7/28/2019 Denon AVR-2112ci Eng manual

1/137

INTEGRATED NETWORK AV RECEIVER

AVR-2112CIOwners Manual

Basicversion

Advanced

version

Information


2/137

I

nSAFETY PRECAUTIONS

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVECOVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ash with arrowhead symbol, within an equilateraltriangle, is intended to alert the user to the presence o

uninsulated dangerous voltage within the products enclosure

that may be o sufcient magnitude to constitute a risk o

electric shock to persons.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence o important operating

and maintenance (servicing) instructions in the literature

accompanying the appliance.

WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOTEXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:To completely disconnect this product rom the mains, disconnect the plug

rom the wall socket outlet.

The mains plug is used to completely interrupt the power supply to the unit

and must be within easy access by the user.

IMPORTANT SAFETYINSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the manuacturers instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifers) that produce heat.9. Do not deeat the saety purpose o the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding pr ong. The wide blade or the

third prong are provided or your saety. I the provided plug does not ft into

your outlet, consult an electrician or replacement o the obsolete outlet.

10. Protect the power cord rom being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit rom the

apparatus.

11. Only use attachments/accessories specifed by the manuacturer.

12. Use only with the cart, stand, tripod, bracket, or table

specifed by the manuacturer, or sold wit h the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury rom tip-over.

13. Unplug this apparatus during lightning storms or when

unused or long periods o time.

14. Reer all servicing to qualifed service personnel.Servicing is required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been spilled or

objects have allen into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been dropped.

15. Batteries shall not be exposed to excessive heat such as sunshine, fre or

the like.

FCC INFORMATION (For US customers)

1. COMPLIANCE INFORMATIONProduct Name: Integrated Network AV Receiver

Model Number: AVR-2112CI

This product complies with Part 15 o the FCC Rules. Operation is subject

to the ollowing two conditions: (1) this product may not cause harmul

intererence, and (2) this product must accept any intererence received,

including intererence that may cause undesired operation.

Denon Electronics (USA), LLC

(a D&M Holdings Company)

100 Corporate Drive

Mahwah, NJ 07430-2041Tel. (800) 497-8921

2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCTThis product, when installed as indicated in the instructions contained

in this manual, meets FCC requirements. Modifcation not expressly

approved by DENON may void your authority, granted by the FCC, to use

the product.

3. IMPORTANTWhen connecting this product to network hub or router, use only a

shielded STP or ScTP LAN cable which is available at retailer.

Follow all installation instructions. Failure to ollow instructions could void

your authority, granted by the FCC, to use the product.

4. NOTEThis product has been tested and ound to comply with the limits or

a Class B digital device, pursuant to Part 15 o the FCC Rules. Theselimits are designed to provide reasonable protection against harmul

intererence in a residential installation.

This product generates, uses and can radiate radio requency energy and,

i not installed and used in accordance with the instructions, may cause

harmul intererence to radio communications. However, there is no

guarantee that intererence will not occur in a particular installation. I this

product does cause harmul intererence to radio or television reception,

which can be determined by turning the product OFF and ON, the user

is encouraged to try to correct the intererence by one or more o the

ollowing measures:

Reorientorrelocatethereceivingantenna.

Increasetheseparationbetweentheequipmentandreceiver.

Connecttheproductintoan outletona circuitdifferentfromthatto

which the receiver is connected.

Consultthelocalretailerauthorizedtodistributethistypeofproductor

an experienced radio/TV technician or help.

For Canadian customers:

This Class B digital apparatus complies with Canadian ICES-003.

CAUTION:HOT SURFACE. DO NOT TOUCH.The top surace over the internal heat sink may become hot

when operating this pr oduct continuously.

Do not touch hot areas, especially around the Hot surace

mark and the top panel.

Hot

surace

mark

Basicversion

Advanced

version

Information


3/137

II

nNOTES ON USE

WARNINGS

Avoid high temperatures.

Allow or sufcient heat dispersion when installed in a rack.

Handle the power cord careully.

Hold the plug when unplugging the cord.

Keep the unit ree rom moisture, water, and dust.

Unplug the power cord when not using the unit or long periods o time.

Do not obstruct the ventilation holes.

Do not let oreign objects into the unit.

Do not let insecticides, benzene, and thinner come in contact with the unit.

Never disassemble or modiy the unit in any way.

Ventilation should not be impeded by covering the ventilation openings

with items, such as newspapers, tablecloths or curtains.

Naked ame sources such as lighted candles should not be placed on

the unit.

Observe and ollow local regulations regarding battery disposal.

Do not expose the unit to dripping or splashing uids.

Do not place objects flled with liquids, such as vases, on the unit.

Do not handle the mains cord with wet hands.

When the switch is in the OFF (STANDBY) position, the equipment is not

completely switched o rom MAINS.

The equipment shall be installed near the power supply so that the power

supply is easily accessible.

nCAUTIONS ON INSTALLATION

z z

z

Wall

z

z For proper heat dispersal, do not install this unit in a connedspace, such as a bookcase or similar enclosure.More than 12 in. (0.3 m) is recommended.

Do not place any other equipment on this unit.

Basicversion

Advanced

version

Information


4/137

1

Thank you or purchasing this DENON product. To ensure proper operation, please read this owners manual careully beore using the product.

Ater reading them, be sure to keep them or uture reerence.

Getting started

Basic version3

Connections 4Important inormation 4

Connecting an HDMI-compatible device 6

Connecting a TV8

Connecting a Blu-ray Disc player/DVD player 8

Connecting a set-top box (Satellite tuner/Cable TV) 9

Connecting a digital camcorder 9

Connecting a control dock or iPod 10

Connecting an iPod or USB memory device to the USB port 10

Connecting an antenna 11

Connecting a CD player 11

Connecting to a home network (LAN) 12Connecting an external control device13

Settings14Set up speakers (Audyssey Auto Setup) 14

Making the network settings (Network Setup)20

Playback (Basic operation) 21Important inormation 21

Playing a Blu-ray Disc player/DVD player 22

Playing a CD player 22

Playing an iPod23

Tuning in r adio stations 27

Playing a network audio 29

Playing a USB memory device44

Selecting a listening mode (Surround mode) 46Selecting a listening mode46

Advanced version 50

Speaker installation/connection (Advanced connection) 51Install 51

Connect 53

Set up speakers 58Playback (Advanced operation) 60

Convenient unc tions 60

Playback in ZONE2 (Separate room) 70Audio output 70

Playback 71

Quick select unction 72

Sleep timer unction 72

How to make detailed settings73Menu map 73

Examples o menu screen displays 74

Examples o menu and ront display 75

Inputting characters 76

Audio Adjust 78

Inormation 84

System Setup 85

Input Setup 99

Operating the connected devices by remote control unit 105Operating AV devices 105

Registering preset codes 106

Operating devices 108

Speciying the zone used with the main remote control unit 110

Resetting the remote control unit110

Inormation111

Part names and unctions112Front panel 112

Display 113

Rear panel 114Remote control unit 115

Other inormation 117Trademark inormation117

Surround 118

Relationship between video signals and monitor output 122

Explanation o terms 123

Troubleshooting 126Resetting the microprocessor 129

Specications 130

Getting started 1Accessories 1

Features 2

Cautions on handling 2

AccessoriesCheck that the ollowing parts are supplied with the product.

q Getting Started ........................................................................1

w CD-ROM (Owners manual) .................................................... 1e Warranty (or North America model only) ................................1r Service network l ist .................................................................1t Remote control unit (RC-1156) ................................................1y R6/AA batteries ....................................................................... 2u Setup microphone (DM-A409) .................................................1i AM loop antenna .....................................................................1o FM indoor antenna ..................................................................1

t

i o

u

Contents

Basicversion

Advanced

version

Infor

mation


5/137

2

Features

Fully discrete, identical quality and power or all7 channels (125 W x 7ch)The unit is equipped with a power amplifer that reproduces high-

fdelity sound in surround mode with equal quality and power or all

channels, true to the original sound.

The power amplifer circuit adopts a discrete-circuit confguration

that achieves high-quality surround sound reproduction.

Supports internet radio, music, and photographstreamingSupports AirPlay (vpage 64)When connected to a network, this unit can play audio fles and sti ll

images such as photographs that are stored on your computer. You

can also listen to internet radio and a host o other online music

sources that use network technology. This unit also supports

AirPlay that lets you stream your music library rom an iPhone,

iPad, iPod touch or iTunes.

Compatible with Denon Remote App orperorming basic operations o the unit with an

iPhone or iPod touchz1Denon Remote App is application sotware that allows you to

perorm basic operations with an iPhone or iPod touch such as

turning the unit ON/OFF, controlling the volume, and switching the

source.

z1 Download Denon Remote App rom iTunes App Store.The unit needs to be connected to a LAN and the iPhone/iPod

touch needs to be connected to the same network by Wi-Fi

(wireless LAN).

Setup wizard, providing easy-to-ollow setupinstructionsFirst select the language when prompted. Then simply ollow the

instructions displayed on the TV screen to set up the speakers,

network, etc.

Easy to use, Graphical User InteraceThis unit is equipped with an easy to see Graphical User Interace

that uses menu displays and levels. The use o level displays

increases operability o the this unit.

Direct play or iPod and iPhone via USB(vpage 10)Music data rom an iPod can be played back i you connect the USB

cable supplied with the iPod via the USB port o this unit, and also

an iPod can be controlled with the remote control unit or this unit.

When an iPod is connected, merely pressing iPod 1 on the mainunit starts playback o music rom the iPod.

Supports HDMI 1.4a with 3D, ARC, Deep Color,x.v.Color, Auto Lip Sync and HDMI controlunction (vpage 6)This unit can output 3D video signals input rom a Blu-ray Disc

player to a TV that supports a 3D system. This unit also supports

the ARC (Audio Return Channel) unction, which reproduces TV

sound with this unit via an HDMI cable used or connecting the

unit and a TVz2.

z2 The TV should support the ARC unction.

6-HDMI inputs and 1-outputThe unit is equipped with 6 HDMI input connectors or connecting

devices with HDMI connectors, such as a Blu-ray Disc player,

game machine, HD video camera, etc.

High denition audio supportThe unit is equipped with a decoder which supports high-quality

digital audio ormat or Blu-ray Disc players such as Dolby TrueHD,

DTS-HD Master Audio, etc.

Cautions on handling

Beore turning the power onCheck once again that all connections are correct and that there are

no problems with the connection cables.

Power is supplied to some o the circuitry even when the unit is

set to the standby mode. When going on vacation or leaving home

or long periods o time, be sure to unplug the power cord rom the

power outlet.

About condensationI there is a major dierence in temperature between the inside o

the unit and the surroundings, condensation (dew) may orm on

the operating parts inside the unit, causing the unit not to operate

properly.

I this happens, let the unit sit or an hour or two with the power

turned o and wait until there is little dierence in temperature

beore using the unit.

Cautions on using mobile phonesUsing a mobile phone near this unit may result in noise. I that

occurs, move the mobile phone away rom this unit when it is in use.

Moving the unitTurn o the power and unplug the power cord rom the power

outlet. Next, disconnect the connection cables to other system units

beore moving the unit.

About careWipe the cabinet and control panel clean with a sot cloth.

Follow the instructions when using a chemical cleaner.

Benzene, paint thinner or other organic solvents as well as

insecticide may cause material changes and discoloration i brought

into contact with the unit, and should thereore not be used.

Basicversion

Advanced

version

Infor

mation


6/137

Basicversion

3

F Connections vpage 4F Settings vpage 14F Playback (Basic operation) vpage 21F Selecting a listening mode (Surround mode) vpage 46

Connection vpage 7, 8 Connection vpage 7, 8

Playback Playback vpage 22

Connection vpage 7, 8 Connection vpage 11

Playback vpage 22 Playback vpage 22

Connection vpage 7, 9 Connection vpage 10

Playback Playback vpage 23

Connection vpage 10 Connection vpage 10

Playback vpage 25 Playback vpage 44Connection vpage 7 Connection vpage 7, 9

Playback Playback

Connection vpage 11 Connection vpage 12

Playback vpage 27 Playback vpage 29

For speaker connections, see page 53, Cpage 6 Connecting the speakers.

Basic versionHere, we explain the connections and basic operation methods or this unit.

Basicversion

Advanced

version

Infor

mation

Basicversion


7/137

4

Important inormationMake connections as ollows beore using this unit. Select an

appropriate connection type according to the devices to beconnected.You may need to make some settings on this unit depending

on the connection method. Reer to each description or moreinormation.Select the cables (sold separately) according to the devices

being connected.

NOTE

Do not plug in the power cord until all connections have been

completed. (When the Setup wizard is running, oll ow the instructions

in the Setup wizard screen or making connections.)

When running the Setup wizard, turn o the power supply o

connected devices.

When making connections, also reer to the operating inst ructions o

the other devices being connected.

Be sure to connect the let and right channels properly (let with let,

right with right).

Do not bundle power cords together with connection cables. Doing

so can result in noise.

Connections

Converting input video signals or output (Video conversion unction)This unit is equipped with our types o video input connectors (HDMI, Component video, S-Video and video) and two types o video output

connectors (HDMI and video).

Use the connectors corresponding to the devices to be connected.

This unction automatically converts various ormats o video signals input to this unit into the ormats used to output the video signals romthis unit to a monitor.

GFlow o video signals or MAIN ZONEH

HDMI connector

Component video

connectors

S-Video connector

Video connector

Monitor (TV)

HDMI connector

Component video

connectors

S-Video

connector

Video connector

HDMI

connector

Video connector

HDMI connector

Video connector

Video deviceThis unit

Output

Input(IN)

Output(MONITOR OUT) Input

The video conversion unction supports the NTSC, PAL, SECAM, NTSC 4.43, PAL-N, PAL-M and PAL-60 ormats.

Resolutions o HDMI-compatible TVs can be checked atHDMI Monitor Inormation (vpage 84).NOTE

HDMI signals cannot be converted into analog signals.

Component video input signals cannot be converted into Video ormat.

When a non-standard video signal rom a game machine or some other source is input, the video conversion unction might not operate.

Basicversion

Advanced

version

Infor

mation

Basicversion

vSee overleaf


8/137

5

Important inormation

Examples o screen display

Menu screen Status display screen

When the input source is

switched.

When the volume is adjusted.

Audio Adjust

Information

Setup Wizard

System Setup

Input Setup

Surr.Parameter

Tone

AudysseySettings

Manual EQ

RESTORER

Audio Delay

Menu

SOURCE :BD

MODE :STEREO[Auto]

Master Volume -55.5dB

Status display: The operating status appears briey on the screen

when the input source is switched or the volume is

changed.

NOTE

I you operate the menu while playing back 3D video content or computers resolution (e.g. VGA), the

playback video is replaced by the menu screen. The playback video is not displayed behind the menu

screen.

This unit does not show the status display while playing back 3D video content or computers resolution

(e.g. VGA).

The menu screen and status display are displayed when this unit and a TV are connected by HDMI.

Furthermore, the menu screen and status display are not displayed when this unit and a TV are connectedby VIDEO and COMPONENT VIDEO.

Basicversion

Advanced

version

Infor

mation

Basicversion


9/137

6

Connecting an HDMI-compatible deviceYou can connect up to seven HDMI-compatible devices (6-inputs/1-output) to the unit.

HDMI unctionThis unit supports the ollowing HDMI unctions:

3D

Deep Color (vpage 123)Auto Lip Sync (vpage 89, 123)x.v.Color, sYCC601 color, Adobe RGB color, Adobe YCC601 color (vpage 123, 124, 125)High defnition digital audio ormat

ARC (Audio Return Channel)Content Type

CEC (HDMI control)

Copyright protection system

In order to play back digital video and audio such as BD-Video or DVD-Video via HDMI connection, both

this unit and TV or the player need to support the copyright protection system known as HDCP (High-

bandwidth Digital Content Protection System). HDCP is copyright protection technology comprised o

data encryption and authentication o the connected AV devices. This unit supports HDCP.

I a device that does not support HDCP is connected, video and audio are not output correctly. Read

the owners manual o your television or player or more inormation.

About HDMI cablesWhen a device supporting Deep Color is connected, use a cable compatible with High Speed HDMI

cable or High Speed HDMI cable with Ethernet.When the ARC unction is used, connect a device with a Standard HDMI cable with Ethernet or High

Speed HDMI cable with Ethernet or HDMI 1.4a.

HDMI control unction (vpage 60)This unction allows you to operate external devices rom the unit and operate the unit rom external

devices.

NOTE

The HDMI control unction may not work depending on the device it is connected to and its settings.

You cannot operate a TV or Blu-ray Disc player/DVD player that is not compatible with the HDMI control

unction.

About 3D unctionThis unit supports input and output o 3D (3 dimensional) video signals o HDMI 1.4a.

To play back 3D video, you need a TV and player that provide support or the HDMI1.4a 3D unction and

a pair o 3D glasses.

NOTE

When playing back 3D video, reer to the instructions provided in the manual o your playback device

together with this manual.

I you operate the menu while playing back 3D v ideo content, the playback video is replaced by the menuscreen. The playback video is not displayed behind the menu screen.

This unit does not show the status display while playing back 3D video content.

I 3D video with no 3D inormation is input, the menu screen and status display on this unit are displayed

over the playback video.

I 2D video is converted to 3D video on the television, the menu screen and status display on this unit

are not displayed correctly. To view the menu screen and status display on this unit correctly, turn the

television setting that converts 2D video to 3D video o.

About ARC (Audio Return Channel) unctionThe Audio Return Channel in HDMI 1.4a enables a TV, via a single HDMI cable, to send audio data upstream

to this unit.

NOTE

To enable the ARC unction, set HDMI Control to ON (vpage 89).When connecting a TV that does not support the ARC unction, a separate connection using an audio

cable is required. In this case, reer to Connecting a TV (vpage 8) or the connection method.

About Content TypeHDMI 1.4a enables simple, automated picture setting selection with no user intervention.

NOTE

To enable the Content Type, set Video Mode to Auto (vpage 102).

Basicversion

Advanced

version

Infor

mation

Basicversion

vSee overleaf
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-


10/137

7

Connecting an HDMI-compatible device

When this unit is connected to other devices with HDMI cables, connect this unit and TV also with an

HDMI cable.

When connecting a device that supports Deep Color, please use a High Speed HDMI cable or High

Speed HDMI cable with Ethernet.

Video signals are not output i the input video signals do not match the monitors resolution. In this case,

switch the Blu-ray Disc/DVD players resolution to a resolution with which the monitor is compatible.

When this unit and monitor are connected with an HDMI cable, i the monitor is not compatible with

HDMI audio signal playback, only the video signals are output to the monitor.

NOTE

The audio signal rom the HDMI output connector (sampling requency, number o channels, etc.) may be

limited by the HDMI audio specifcations o the connected device regarding permissible inputs.

Connecting to a device equipped with a DVI-D connectorWhen an HDMI/DVI conversion cable (sold separately) is used, the HDMI video signals are converted to

DVI signals, allowing connection to a device equipped with a DVI-D connector.

NOTE

No sound is output when connected to a device equipped with a DVI-D connector. Make separate audio

connections.

Signals cannot be output to DVI-D devices that do not support HDCP.

Depending on the combination o devices, the video signals may not be output.

nSettings related to HDMI connectionsSet as necessary. For details, see the respective reerence pages.

Input Assign (vpage 101)Set this to change the HDMI input connector to which the input source is assigned.

HDMI Setup (vpage 89)Make settings or HDMI video/audio output.

Auto Lip Sync HDMI Audio Out HDMI Control

Standby Source P.O Control

NOTE

The audio signal input rom the HDMI input connector can be output as an output signal rom the HDMI

output connector by setting the HDMI audio output destination to TV.Audio signals input via the Analog/Coaxial/Optical input connectors cannot be output rom the HDMI

output connector.

Cables used or connections

Audio and video cable (sold separately)

HDMI cable

This interace allows transer o digital video signals and digital audio signals over a single HDMI cable.

OUT

HDMI

OUT

HDMI

OUT

HDMI

OUT

HDMI

IN

HDMI

OUT

HDMI

OUT

HDMI

Blu-rayDisc

playerDVD

player TVSet-top

boxGame

console 1Game

console 2Digital

camcorder

Basicversion

Advanced

version

Information

Basicversion


11/137

8

Connecting a Blu-ray Disc player/DVD playerYou can enjoy video and audio rom a Blu-ray Disc or DVD.

Select the connector to use and connect the device.

For instructions on HDMI connections, see Connecting an HDMI-compatible device (vpage 6).

Cables used or connectionsVideo cable (sold separately)

Video cable

Audio cables (sold separately)

Audio cableR

L

R

L

RL

RL

RL

RL

VIDEO AUDIO

AUDIO

RL

OUT

AUDIO

AUDIO

RL

OUTOUT

VIDEO

Blu-ray DiscplayerDVD player

Set this to change the digital input connector or component video input connector to which the input

source is assigned.

Input Assign (vpage 101)

in Set as Necessary

When you want to play back HD Audio (Dolby TrueHD, DTS-HD, Dolby Digital Plus, DTS Express ) and Multi-

channel PCM with this unit, use an HDMI connection (vpage 6 Connecting an HDMI-compatibledevice).

Connecting a TVSelect the connector to use and connect the device.

For video connections, see Converting input video signals or output (Video conversion unction)

(vpage 4).For instructions on HDMI connections, see Connecting an HDMI-compatible device (vpage 6).

To listen to TV audio through this device, use the optical digital connection.

NOTE

The optical connection is not required when a TV compatible with the ARC unction (Audio Return ChannelHDMI 1.4a standard unction) is connected to this unit via an HDMI connection.

For details, see About ARC (Audio Return Channel) unction (vpage 6) or reer to the instructionmanual or your TV.


Video cable

Audio cable (sold separately)

Optical cable

IN

VIDEO

AUDIO

OPTICAL

OUT

VIDEO

TV


source is assigned.


in Set as Necessary

Basicversion

Advanced

version

Information

Basicversion


12/137

9

Connecting a digital camcorderYou can enjoy video and audio rom a digital camcorder.



Video cable


Audio cableR

L

R

L

RL

RL

OUT

AUDIOVIDEO

VIDEO AUDIO

RL

OUT

Digital camcorder


source is assigned.


in Set as Necessary

You can enjoy games by connecting a game machine via the V.AUX input connector. In this case, select

the input source to V.AUX.

NOTE

When a non-standard video signal rom a game machine or some other source is input, the video conversion

unction might not operate. In this case, use the monitor output o the same connector as the input.

Connecting a set-top box (Satellite tuner/Cable TV)You can watch satellite or cable TV.




Video cable

Componentvideo cable

Audio cables (sold separately)

Audio cableR

L

R

L

Coaxial

digital cable

RL

RL

VIDEO AUDIO

AUDIO

RL

OUTOUT

VIDEOCOMPONENT VIDEO

Y PB PR

OUT OUT

COAXIAL

Satellite tuner/Cable TV


source is assigned.


in Set as Necessary

Basicversion

Advanced

version

Information

Basicversion


13/137


14/137

11

Connecting an antennaConnect the FM antenna or AM loop antenna supplied with the unit

to enjoy listening to radio broadcasts.

Ater connecting the antenna and receiving a broadcast signal

(vpage 27 Listening to FM/AM broadcasts), fx the antennawith tape in a position where the noise level becomes minimal.

w eq

FM outdoor

antenna

Direction o broadcasting station

75 coaxial

cable

GroundAM outdoor

antenna

AM loop antenna

(supplied)

Black

White FM indoor

antenna

(supplied)

nAM loop antenna assembly

1Put the stand section

through the bottom of the

loop antenna from the

rear and bend it forward.

Stand

Square

hole

Projecting

part

Loop

antenna

2Insert the projecting part

into the square hole in

the stand.

nUsing the AM loop antennaSuspending on a wallSuspend directly on a wall without assembling.

Nail, tack, etc.

Standing aloneUse the procedure shown above to assemble.

NOTE

Do not connect two FM antennas simultaneously.

Even i an external AM antenna is used, do not disconnect the AM

loop antenna.

Make sure the AM loop antenna lead terminals do not touch metal

parts o the panel.

I the signal has noise intererence, connect the ground terminal

(GND) to reduce noise.

I you are unable to receive a good broadcast signal, we recommend

installing an outdoor antenna. For details, inquire at the retail store

where you purchased the unit.

Connecting a CD playerYou can enjoy CD sound.




Audio cableR

L

R

L

RL

RL

AUDIO

AUDIO

RL

OUT

CD player

Set this to change the digital input connector to which the input

source is assigned.


in Set as Necessary

Basicversion

Advanced

version

Information

Basicversion


15/137

12

Connecting to a home network (LAN)This unit lets you play via your home network (LAN) music fles

stored on a computer and music content such as that rom Internet

radio.

You can also operate this unit rom a computer using the Web

control unction.

You can update by downloading the latest frmware rom the

DENON website.

For more inormation, on the menu, select Firmware Update

(vpage 96).See Network Setup on the menu (

vpage 91) or more

inormation on network setting.


Cable (sold separately)

Ethernet

cable

Internet

To WAN side

Router

To LAN port

To LAN portLAN port/Ethernet

connector

Computer

Modem

For connections to the Internet, contact an ISP (InternetService Provider) or a computer shop.

Required system

nBroadband internet connectionnModemDevice that connects to the broadband circuit and conducts

communications on the Internet.

A type that is integrated with a router is also available.

nRouterWhen using this unit, we recommend you use a router equippedwith the ollowing unctions:

Built-in DHCP server

This unction automatically assigns IP addresses on the LAN.

Built-in 100BASE-TX switch

When connecting multiple devices, we recommend a switching

hub with a speed o 100 Mbps or greater.

n Ethernet cable (CAT-5 or greater recommended)Use only a shielded STP or ScTP LAN cable which is available at

retailer.

Some at type Ethernet cables are easily aected by noise.

We recommend using a normal type cable.

I you have an Internet provider contract or a line on which network

settings are made manually, make the settings at Network Setup

(vpage 91).With this unit, it is possible to use the DHCP and Auto IP unctions

to make the network settings automatically.

When using this unit with the broadband routers DHCP unction

enabled, this unit automatically perorms the IP address setting and

other settings.

When using this unit connected to a network with no DHCP

unction, make the settings or the IP address, etc., at Network

Setup (vpage 91).When setting manually, check the setting contents with the network

administrator.

NOTE

A contract with an ISP is required to connect to the Internet.

No additional contract is needed i you already have a broadband

connection to the Internet.

The types o routers that can be used depend on the ISP. Contact an

ISP or a computer shop or details.

DENON assumes no responsibility whatsoever or any

communication errors or troubles resulting rom customers

network environment or connected devices.

This unit is not compatible with PPPoE. A PPPoE-compatible router

is required i you have a contract or a type o line set by PPPoE.

Do not connect an ETHERNET connector directly to the LAN port/

Ethernet connector on your computer.

To listen to audio streaming, use a router that supports audio

streaming.

Basicversion

Advanced

version

Information

Basicversion


16/137

13

Connecting an external control device

REMOTE CONTROL jacksI this unit is installed in a location that is out o range o the signal

rom the remote control unit, you can still operate the unit and the

devices connected to it by using a commercially available IR receiver.

You can also use it to remotely control ZONE2 (another room).

AUX

OUT

Device equipped with aREMOTE CONTROL IN jack

Inraredretransmitter

Inraredsensor

OutputInput

RS-232C connectorWhen you connect an external control device, you can control this unit

with the external control device.

External serial controller

Perorm the operation below beorehand.

q Turn on the power o this unit.

w Turn o the power o this unit rom the external controller.

e Check that the unit is in the standby mode.

Basicversion

Advanced

version

Information

Basicversion


17/137

14

The acoustic characteristics o the connected speakers andlistening room are measured and the optimum settings are madeautomatically. This is called Audyssey Auto Setup.

To perorm measurement, place the setup microphone inmultiple locations all around the listening area. For best results,we recommend you measure in six or more positions, as shownin the illustration (up to eight positions).When perorming Audyssey Auto Setup, Audyssey MultEQ XT/

Audyssey Dynamic EQ/Audyssey Dynamic Volume unctions

become active (vpage 81, 82).To set up the speakers manually, use Speaker Setup

(vpage 86) on the menu.

NOTE

Make the room as quiet as possible. Background noise can disrupt

the room measurements. Close windows, silence cell phones,

televisions, radios, air conditioners, uorescent lights, home

appliances, light dimmers, or other devices as measurements may

be aected by these sounds.

Cell phones should be placed away rom all audio electronics during

the measurement process as Radio Frequency Intererence (RFI)

may cause measurement disruptions (even i the cell phone is not

in use).

Do not unplug the setup microphone rom the main unit until

Audyssey Auto Setup is completed.

Do not stand between the speakers and setup microphone or allow

obstacles in the path while the measurements are being made. This

will cause inaccurate readings.

Loud test sounds may be played during Audyssey Auto setup. This

is part o normal operation. I there is background noise in room,

these test signals will increase in volume.

OperatingMdfduring the measurements

will cancel the measurements.Measurement cannot be perormed when

headphones are connected.

SettingsHere, we explain Audyssey Auto Setup, which allows you to

automatically make the optimal settings or your speakers, and

Network Setup, which allows you to connect this unit to a home

network (LAN).

This unit lets you play via your home network (LAN) music fles stored

on a computer and music content such as that rom Internet radio.

Selecting a listening mode (Surround mode)(vpage 46)

Playback (Basic operation) (vpage 21)

n Set up speakers (Audyssey Auto Setup)(vpage 14)

n Making the network settings (Network Setup)(vpage 20)

Playback (Advanced operation) (vpage 60)

Set up speakers (Audyssey Auto Setup)

About setup microphone placement

Measurements are perormed by placing the setup microphone

successively at multiple positions throughout the entire listening

area, as shown in GExampleqH. For best results, we recommendyou measure in six or more positions, as shown in the illustration

(up to eight positions).

Even i the listening environment is small as shown inGExamplewH,measuring at multiple points throughout the listening environment

results in more eective correction.

FL SW C FR

SRSL*M

FL SW C FR

SRSL *M

( : Measuring positions)

GExampleqH GExamplewH

( : Measuring positions)

FL Front speaker (L) SW SubwooerFR Front speaker (R) SL Surround speaker (L)C Center speaker SR Surround speaker (R)

About the main listening position (*M)The main listening position is the position where listeners would

normally sit or where one would normally sit alone within the listening

environment. Beore starting Audyssey Auto Setup, place the setup

microphone in the main listening position. Audyssey MultEQ XT usesthe measurements rom this position to calculate speaker distance,

level, polarity, and the optimum crossover value or the subwooer.

Basicversion

Advanced

version

Information

Basicversion

vSee overleaf


18/137

15

2 Set up the subwooerIf using a subwoofer capable of the following

adjustments, set up the subwoofer as shown below.

n When using a subwooer with a direct modeSet the direct mode to On and disable the volume adjustment

and crossover requency setting.

n When using a subwooer without a direct modeMake the ollowing settings:

Volume : 12 oclock positionCrossover requency : Maximum/Highest FrequencyLow pass lter : OStandby mode : O

1 Set up the microphoneMount the setup microphone on a tripod or stand

and place it in the main listening position.When placing the setup microphone, adjust the height o the

sound receptor to the level o the listeners ear.

Sound receptorSetup

microphone

I you do not have a tripod or stand, set up the microphone on, orexample, a seat without a back.

NOTE

Do not hold the setup microphone in your hand during

measurements.

Avoid placing the setup microphone close to a seat back or wall as

sound reections may give inaccurate results.


3 Set up the remote control unitn Set up the zone modePress ZONE SELECT to switch the zone mode toJ (MAIN ZONE).The J indicator lights.

Press ZONE SELECT

n Set up the operation modePress AMP to set the remote control unit to AMP-operation mode.

Press AMP

Basicversion

Advanced

version

Information

Basicversion

vSee overleaf


19/137

16

STEP 1

PreparationSTEP 2

Detect & Measure (Main)


4Connect the setup microphone to the SETUP MIC

jack of this unit.

MultEQ XT

Preparation

Connect the speakers and place then according

to the recommendations in the manual.

Next

Audyssey Auto Setup

[RETURN][ENTER] Enter Cancel

When the setup microphone is

connected, the ollowing screen is

displayed.

5Select Next and then press

ENTER.

In STEP 2, you will perorm measurements at the main listening

position.

This step automatically checks the speaker confguration and speaker

size, and calculates the channel level, distance, and crossover

requency.

It also corrects distortion in the listening area.

7Select Measure and then press ENTER.When measuring begins, a test tone is output rom each

speaker.

Measurement requires several minutes.

8The detected speakers are displayed.

The illustration below shows an example o when the ront

speakers, center speaker, subwooer, and surround speakers have

been detected.

Detect CheckFrontCenterSubwooferSurround

Retry

Next Measure

YesYesYesYes

[ENTER] Enter

Audyssey Auto Setup MultEQ XT

[RETURN] Cancel

NOTE

I a connected speaker is not displayed, the speaker may not be

connected correctly. Check the speaker connection.

9Use ui to select Next Measure and then press

ENTER.

6Use ui to select Auto Setup Start and then pressENTER.

PreparationSet the following itemsif necessary.

Amp AssignChannel Select

Auto Setup Start



Here, we explain setup using the example o 5.1-channel speaker

playback.For settings other than 5.1-channel surround, select Amp Assign

and perorm step 4 to 5 o Set up Amp Assign (vpage 58).I unused channels are set with Channel Select, measuring time

can be shortened. For setting, perorm steps 7 to 11 o Set upChannel Select (vpage 59).

Basicversion

Advanced

version

Information

Basicversion

vSee overleaf


20/137

17

STEP 4

Calculate


In STEP 3, you will perorm measurements at multiple positions (two

to eight positions) other than the main listening position.

Just one position can be measured but measuring multiple positions

increases the accuracy o the correction o acoustic distortion within

the listening area.

10Move the setup microphone to

position 2, use ui to selectMeasure, and then press

ENTER.The measurement o the second

position starts. Measurements can be

made in up to eight positions.


Measure (2nd)Please place themicrophone at earheight at 2ndlistening position.

Measure

Next Calculate


I you want to omit measurements rom the next position onward,

select Next Calculate.

(Go to STEP4 Calculate )

11Repeat step 10, measuring positions 3 to 8.When measurement o position 8 is completed, a

Measurements fnished. message is displayed.


Measure (Finish)Measurements finished.

Next Calculate

Retry


12On the STEP 3 screen, use ui to select Next Calculate, and then press ENTER.Measuring results are analyzed, and the requency response o

each speaker in the listening room is determined.


CalculateNow calculatingPlease wait

0%

Analysis takes several minutes to complete. The time required or

this analysis depends on the number o speakers connected.

The more connected speakers there are, the longer it takes to

perorm analysis.

STEP 3

Measure (2nd 8th)STEP 2 (Continued)

Detect & Measure (Main)

NOTE

I Caution is displayed:Go to Error messages (vpage 19),check any related items, and perorm the

necessary procedures.

I the problem is resolved, return and restartAudyssey Auto Setup.

When perorming Audyssey Auto Setup overagainPressui to select Retry, and then press ENTER.

When measuring has stoppedq Press RETURN B, to the Cancel Auto Setup? prompt is

displayed.

w Press o to select Yes, then press ENTER.

Setting up the speakers again

Repeat the operation rom step 4 o STEP 1 Preparation .

Basicversion

Advanced

version

Information

Basicversion

vSee overleaf


21/137

18


15Select Store and then press ENTER.Save the measurement results.


StoreNow storingPlease wait

0%


Store

Press Store tostore calculationresult.

Store


Saving the results requires about 10 seconds.

I the measuring results are not to be saved, press RETURN B.A message Cancel Auto Setup? will be displayed. Press o thenselect Yes. All the measured Audyssey Auto Setup data will

be erased.

During saving o measurements results, Now storing Please

wait... is displayed. When saving is completed, Storing complete.

Auto Setup is now fnished. is displayed.

NOTEDuring saving o measurement results, be sure not to turn o the

power.

16Unplug the setup microphone from the units SETUP

MIC jack.

17Set Audyssey Dynamic Volume.

FinishStoring complete.Auto Setup is now finished.Please unplug microphone.

Turn on Dynamic Volume?

Yes

No

[ENTER] Exit


This eature adjusts the output volume to the optimal level while

constantly monitoring the level o the audio input to the unit.

Optimal volume control is perormed automatically without any

loss in the dynamism and clarity o the sound when, or example,

the volume suddenly increases or commercials shown duringtelevision programs.

n When turning Dynamic Volume onUse u to select Yes, and then press ENTER.

The unit automatically enters Evening mode.

n When turning Dynamic Volume oUse i to select No, and then press ENTER.

NOTE

Ater perorming Audyssey Auto Setup, do not change the speaker

connections or subwooer volume. In event o a change, perorm

Audyssey Auto Setup again.

STEP 6

Store FinishSTEP 5

Check

13Use ui to select the item youwant to check, and then press

ENTER.

MultEQ XT

CheckCheck processing resuit.To proceed, pressNext.

Next Store

Sp.Config. CheckDistance CheckCh.Level CheckCrossover Check

Audyssey Auto Setup


Subwooers may measure a greater reported distance than

the actual distance due to added electrical delay common in

subwooers.I you want to check another item, press RETURN B.

14Use ui to select Next Store and then pressENTER.

NOTE

I the result diers rom the actual connection status, or i Caution!

is displayed, see Error messages (vpage 19). Then carry outAudyssey Auto Setup again.

I you change speaker positions or orientation, perorm Audyssey

Auto Setup again to fnd the optimal equalizer settings.

Basicversion

Advanced

version

Inform

ation

Basicversion


22/137

19

Error messages

NOTE

An error message is displayed i Audyssey Auto Setup could not be completed due to speaker placement, the measurement environment, etc. I this happens, check the relevant items, be sure to take the necessary

measures, then perorm Audyssey Auto Setup over again.

I the result still diers rom the actual connection status ater remeasurement or the error message still appears, it is possible that the speakers are not connected properly. Turn this unit o, check the speaker

connections and repeat the measurement process rom the beginning.

Be sure to turn o the power beore checking speaker connections.

Examples Error details MeasuresMultEQ XT

Caution!

Microphone or Speaker is none

Retry

Audyssey Auto SetupThe connected setup microphone is broken, or a device other than the

supplied setup microphone is connected.

Not all speakers could be detected.

The ront L speaker was not properly detected.

Connect the included setup microphone to the SETUP MIC jack o this unit.

Check the speaker connections.

MultEQ XT

Caution!

Ambient noise is too high or level is too low

Retry

Audyssey Auto SetupThere is too much noise in the room or accurate measurements to be

made.

Speaker or subwooer sound is too low or accurate measurements to be

made.

Either turn o any device generating noise or move it away.

Perorm again when the surroundings are quieter.

Check the speaker installation and the direction in which the speakers are

acing.

Adjust the subwooers volume.

MultEQ XT

Audyssey Auto Setup

Caution! Speaker:None

Front R

Retry

The displayed speaker could not be detected.

(The screen on the let indicates that the ront right speaker cannot be

detected.)

Check the connections o the displayed speaker.

MultEQ XT

Audyssey Auto Setup

Caution! Speaker:Phase

Front R

SkipRetry

The displayed speaker is connected with the polarity reversed.

(The screen on the let indicates that the polarity phases o the ront right

speakers are reversed.)

Check the polarity o the displayed speaker.

For some speakers, this error message may be

displayed even i the speaker is properly connected.I you are sure the connection is correct, press uito select Skip, then press ENTER.


Basicversion

Advanced

version

Inform

ation

Basicversion


23/137

20

Parameter CheckThis unction enables you to check the measurement results and equalizer characteristics ater Audyssey

Auto Setup.

1Use ui to select Parameter Check and then press ENTER.

Auto Setup

Parameter Check

Auto Setup

Sp. Config. Check

Distance Check

Ch. Level Check

Crossover Check

EQ Check

2Use ui to select the item you want to check, then press ENTER or p.Measurement results or each speaker are displayed.

Sp.Conig. Check Check the speaker confguration.

Distance Check Check the distance.

Ch. Level Check Check the channel level.

Crossover Check Check the crossover requency.

EQ Check Check the equalizer.

I EQ Check is selected, press ui to select equalizing curve (Audyssey or Audyssey Flat) tobe checked.

Use op to switch the display between the dierent speakers.

3Press RETURNB.The confrmation screen reappears. Repeat step 2.

Retrieving Audyssey Auto Setup settingsI you set Restore to Yes, you can return to Audyssey Auto Setup measurement result (value

calculated at the start by MultEQ XT) even when you have changed each setting manually.

Set up speakers (Audyssey Auto Setup) Making the network settings(Network Setup)

This unit can be connected to a home network (LAN) to listen to Internet radio or play back music fles and

still image (JPEG) fles stored on a computer.

1Connect the Ethernet cable (vpage 12 Connecting to a home network (LAN)).

2Turn on this unit (Cpage 5 Getting Started).This unit perorms automatic network setup due to the DHCP unction.

When connecting to a network that has no DHCP unction, perorm the setting in Network

Connect. (vpage 91).

Basicversion

Advanced

version

Inform

ation

Basicversion


24/137


25/137

22

Adjusting the master volume

Use Mdf to adjust the volume.

n When the Volume Display setting(vpage 95) is RelativeGAdjustable rangeH

80.5dB 18.0dB

n When the Volume Display setting (vpage 95) isAbsoluteGAdjustable rangeH 0.0 99.0The variable range diers according to the input signal and channel

level setting.

You can also operate via the main unit. In this case, perorm the

ollowing operations.

Turn MASTER VOLUME to adjust the volume.

Turning o the sound temporarily

Press N.The power indicator ashes green.MUTE indicator on the display lights.

appears on a TV screen.

The sound is reduced to the level set at Mute Level (vpage 95).To cancel, press N again. Muting can also be canceled by adjusting

the master volume.

Playing a Blu-ray Disc player/DVDplayer

The ollowing describes the procedure or playing Blu-ray Disc player/

DVD player.

1Prepare for playback.q Turn on the power o the TV,

subwooer and player.

w Change the TV input to the input othis unit.

e Load the disc in the player.

2Press ON to turn on power to theunit.

3Press BD or DVD to switch an input source for aplayer used for playback.

4Play the device connected to this unit.Make the necessary settings on the player (language setting,

subtitles setting, etc.) beorehand.

Playing a CD playerThe ollowing describes the procedure or playing CD player.

1Prepare for playback.q Turn on the power o the subwooer

and player.

w Load the disc in the player.


3Press CD to switch the inputsource to the CD player.

4Play the device connected to this unit.


Basicversion

Advanced

version

Inform

ation

Basicversion

BD


26/137

23

Playing an iPodThere are two methods or iPod playback.

qUse a DENON control dock or iPod to play back.You can play back both video, photo and audio.

wConnect an iPod directly to the USB port to play back(vpage 25).You can play back audio only.

qUse a DENON control dock or iPod toplay back

I you use a separately sold DENON control dock or iPod (ASD-1R or

ASD-11R), you will be able to play back videos, photos, music, and

other content on the iPod.

n Listening to music on an iPod

1Prepare for playback.q Connect the DENON control dock

or iPod to this unit (vpage 10Connecting a control dock or

iPod).

w Set the iPod in the DENON controldock or iPod.


3Press DOCK to switch the inputsource to DOCK.

I Browse mode is selected in step

4, the ollowing screen is displayed on a

TV screen, depending on the connected

control dock or iPod.

Music

Playlists

Artists

[1/6]

Albums

Songs

Genres

Composers

iPod

Music

Videos

[1/2]

(When using an ASD-1R) (When using an ASD-11R)

In Browse mode, the iPod display is as

shown at right.

NOTE

I the connections screen is not displayed,

the iPod may not be properly connected.

Reconnect it.

OK to disconnect.

4Press SEARCH and hold it down for 2 seconds ormore to select the display mode.

There are two modes or displaying the contents recorded on the

iPod.

Browse mode Display iPod inormation on the TV screen.

English letters, numbers and certain symbols are displayed.

Incompatible characters are displayed as . (period).

Remote mode Display iPod inormation on the iPod screen.

Remote iPod is displayed on the display o this unit.

Display mode Browse mode Remote mode

Playable

les

Music le P P

Photo le Pz2

Video le Pz1 Pz2

Activebuttons

Remotecontrol unit(This unit)

P P

iPod P

z1 When using an ASD-11R DENON control dock or iPod.z2 Video may not be output, depending on the combination o

ASD-1R or ASD-11R DENON control dock or iPod and iPod.

5Use ui to select the item, then press ENTER or pto select the le to be played.

6Press ENTER, p or 1.Playback starts.

You can speciy the duration o the on-screen display to be displayed

(deault: 30 sec) at menu iPod (vpage 96). Press uiop toreturn to the original screen.

To play back compressed audio with extended bass or treble

reproduction, we recommend playback in RESTORER mode

(vpage 83). The deault setting is Mode3.In Browse mode, press STATUS on the main unit during playback

to check the title name, artist name, and album name on the displayo this unit.

NOTE

Press STANDBY and set this units power tothe standby mode beore disconnecting the

iPod. You can also switch the input source

to other than DOCK and then disconnect

the iPod.

Depending on the type o iPod and the sotware version, some

unctions may not operate.

Note that DENON will accept no responsibility whatsoever or any

problems arising with the data on an iPod when using this unit in

conjunction with the iPod.

Basicversion

Advanced

version

Inform

ation

Basicversion

vSee overleaf

BD
http://-/?-http://-/?-http://-/?-


27/137

24

Playing an iPod

nViewing videos on an iPod in the Browse modeWhen an iPod equipped with a video unction is connected to a

DENON ASD-11R control dock or iPod, image fles can be played

in the Browse mode.

1Use ui to select Videos, thenpress ENTER or p.

2Use ui to select the search itemor folder, then press ENTER or

p.

3Use ui to select the video le,then press ENTER, p or 1.Playback starts.

nViewing photos and videos on an iPod in theRemote modeThis unit can play back on a TV screen photos and data stored on an

iPod equipped with a slide show or video unction.

1Press and hold SEARCH to set theRemote mode.Remote iPod is displayed on the

display o this unit.

2Watching the iPods screen,use ui to select Photos orVideos.

Depending on the iPod model, it may be necessary to operate the

iPod unit directly.

3Press ENTER until the image you want to view isdisplayed.

TV Out at the iPods Slide show Settings or Video Settings

must be set to On in order to display the iPods photo data or videos

on the monitor. For details, see the iPods operating instructions.

NOTE

Video may not be output, depending on the combination o ASD-1R or

ASD-11R and iPod.

n iPod operationOperation buttons Function

MENU Amp menu

uiopCursor operation /

Auto search (cue, ui) /Manual search (Press and hold, ui)

ENTER

(Press and release)Enter / Pause

ENTER

(Press and hold)

Stop

SEARCH

(Press and release)Page search modez

SEARCH

(Press and hold)Browse / Remote mode switching

RETURN B Return6 7

(Press and hold)

Manual search

(fast-reverse/fast-forward)

1 Playback / Pause8 9 Auto search (cue)

3 Pause2 Stop

TV Z /X TV power on/standby (Default : SONY)TV INPUT Switch TV input (Default : SONY)

Repeat playback(vpage 104 Repeat)Shuing playback(vpage 104 Shue)

z When the menu screen is displayed, press SEARCH, then press o(previous page) or p (next page).To cancel, press ui or SEARCH.

Basicversion

Advanced

version

Inform

ation

Basicversion

BD


28/137

25

wConnect an iPod directly to the USB portto play back

You can use the USB cable provided with the i Pod to connect the iPod

with the units USB port and enjoy music stored on the iPod.

This unit supports audio playback rom the iPod (fth generation

or later), iPod nano, iPod classic, iPod touch and iPhone (it is not

compatible with iPod shue).

1Connect the iPod to the USB port (

vpage 10

Connecting an iPod or USB memory device to the

USB port).

2Press ON to turn on power to the unit.

3Press NET/USB to switch the input source to NET/USB.

DENON:[AVR-2112CI]

Favorites

Internet Radio

Flickr

Napster

Pandora

Media Server

iPod

[1/8]

CH +/- Preset

4Use ui to select iPod, thenpress ENTER or p.

iPod

Playlists

Artists

Podcasts

Genres

Composers

Albums

Songs

[1/8]

SEARCH P/Search

NOTE

I the iPod is not displayed, the iPod may not be properly

connected. Reconnect it.

Playing an iPod

5Press SEARCH and hold it down for 2 seconds ormore to select the display mode.

There are two modes or displaying the contents recorded on the

iPod.

Browse mode Display iPod inormation on the TV screen.

English letters, numbers and certain symbols are displayed.

Incompatible characters are displayed as . (period).

Remote mode Display iPod inormation on the iPod screen.

Remote iPod is displayed on the display o this unit.

The Remote mode is not supported on fth generation iPod or

frst generation iPod nano.

Display mode Browse mode Remote mode

Playableles

Music le P P

Video le z

Activebuttons

Remotecontrol unit(This unit)

P P

iPod P

z Only the sound is played.

6Use ui to select the item, then press ENTER or pto select the le to be played.

7Press ENTER, p or 1.Playback starts.

You can speciy the duration o the on-screen display to be displayed

(deault: 30 sec) at menu iPod (vpage 96). Press uio pto return to the original screen.



(vpage 83). The deault setting is Mode3.In Browse mode, press STATUS on the main unit during playback to

check the title name, artist name, and album name.

NOTEDepending on the type o iPod and the sotware version, some

unctions may not operate.

Note that DENON will accept no responsibility whatsoever or any

problems arising with the data on an iPod when using this unit in

conjunction with the iPod.

Basicversion

Advanced

version

Inform

ation

Basicversion

vSee overleaf

BD
http://-/?-http://-/?-http://-/?-


29/137

26

n iPod operationOperation buttons Function

MENU Amp menu

uiopCursor operation /

Auto search (cue, ui) /Manual search (Press and hold, ui)

ENTER

(Press and release)Enter / Pause

ENTER

(Press and hold)

Stop

SEARCH

(Press and release)Page searchz1/ Character sortz2

SEARCH

(Press and hold)Browse / Remote mode switching

RETURN B Return6 7

(Press and hold)

Manual search

(fast-reverse/fast-forward)

1 Playback / Pause8 9 Auto search (cue)

3 Pause2 Stop

TV Z /X TV power on/standby (Default : SONY)

TV INPUTSwitch TV input (Default : SONY)

Repeat playback (vpage 104 Repeat)Random playback(vpage 104 Shue)

z1 When the menu screen is displayed, press SEARCH, then presso (previous page) or p (next page).To cancel, press ui or SEARCH twice.

z2 When the menu screen is displayed, press SEARCH twice, thenpress op to select the frst letter you want to search mode.I it is not possible to search the list, unsorted list. is displayed.

To cancel, press ui or SEARCH.

I the list is not in alphabetical order, you may not be able to perorm

a character sort.

Playing an iPod

iPod play unctionI iPod 1 is pressed when a control dock or iPod or an iPod (USB) isconnected, the iPod starts playback.

Press iPod 1.This units input source switches to

DOCK or NET/USB.

iPod playback starts.

NOTE

I both a control dock or iPod (DOCK) and an iPod (NET/USB)

are connected, playback with control dock or iPod (DOCK) takes

priority.

Basicversion

Advanced

version

Inform

ation

Basicversion

BD


30/137

27

Tuning in radio stations

Listening to FM/AM broadcasts

1Press TUNER to switch the inputsource to TUNER.

2Press BAND to select FM orAM.

FM When listening to an FM broadcast.

AM When listening to an AM broadcast.

TUNER

[MEMORY]

Band

Memory

[ ] Mode

A1

[ ]

FM 87.50MHz

Now Playing

AUTO

[CH+/-] Preset

Tuning[ / ]

[ SEARCH ] Search

3Tune in the desired broadcast station.

qTo tune in automatically (Auto tuning)Press MODE to light the AUTO indicator on the display, thenuse TUNING d or TUNING f to select the station you want tohear.

wTo tune in manually (Manual tuning)Press MODE to turn o the displays AUTO indicator, then useTUNING d or TUNING f to select the station you want to hear.

I the desired station cannot be tuned in with auto tuning, tune it in

manually.

When tuning in stations manually, press and hold TUNING d orTUNING fto change requencies continuously.

The time (deault : 30 sec) or which the menu are displayed can beset at menu Tuner (vpage 96). Press uiop to return tothe original screen.

nPresetting radio stations (Manual preset)Your avorite broadcast stations can be preset so that you can tune

them in easily. Up to 56 stations can be preset.

Stations can be preset automatically at Auto Preset(vpage 100). I Auto Preset is perormed ater perormingManual preset, the Manual preset settings will be overwritten.

1Tune in the broadcast station you want to preset.

TUNER

[MEMORY]

Band

Memory

[ ] Mod e

A1

[ ]

FM 87.50MHz

Now Playing

AUTO

[CH+/-] P reset

Tuning[ / ]

[ SEARCH ] Search

2Press MEMORY.

TUNER

A1

To store preset:

Select A1-G8

[MEMORY][1-8][SHIFT]

[MEMORY]

Band

Memory

[ ] Mod e[ ]

[CH+/-] Pre set

Tuning[ / ]

3Press SHIFT to select the block (A to G) in which thechannel (1 to 8 per a block) is to be preset, then press

CH +, CH or 1 8 to select the preset number.

4Press MEMORY again to complete the setting.

To preset other stations, repeat steps 1 to 4.

Deault settingsBlock (A G)

andChannel (1 8)

Deault Settings

A1 A887.50 / 89.10 / 98.10 / 107.90 / 90.10 / 90.10 /

90.10 / 90.10 MHz

B1 B8520 / 600 / 1000 / 1400 / 1500 / 1710 kHz,

90.10 / 90.10 MHz

C1 C8 90.10 MHz

D1 D8 90.10 MHz

E1 E8 90.10 MHz

F1 F8 90.10 MHz

G1 G8 90.10 MHz

Speciy a name or the preset broadcast station(Preset Name) (vpage 100)

Basicversion

Advanced

version

Inform

ation

Basicversion

vSee overleaf

BD
http://-/?-http://-/?-http://-/?-


31/137

28

Tuning in radio stations

n Listening to preset stations

1Press SHIFT to select the memoryblock (A to G).

TUNER

AUTO

[MEMORY]

Band

Memory

[ ] Mode[ ]

[CH+/-] Pre set

Tuning[ / ]

Preset Channel

A8 FM 90.10MHz

A7 FM 90.10MHz

A6 FM 90.10MHz

A5 FM 90.10MHz

A4 FM 107.90MHzA3 FM 98.10MHz

A2 FM 89.10MHz

A1 FM 87.50MHz

2Press CH +, CH or 1 8 to select the desired presetchannel.

You can also operate via the main unit. In this case, perorm the

ollowing operations.

Press TUNER PRESET CH + or TUNER PRESET CH to select a presetradio station.

nDirect requency tuningYou can enter the receiving requency directly to tune in.

1Press SEARCH.

TUNER

FM ---.- MHz

DIRECT TUNE

B6

Now Playing

AUTO

[MEMORY]

Band

Memory

[ ] Mode[ ]

[CH+/-] Pre set

Tuning[ / ]

[ SEARCH ] Search

2Input frequencies using the 0 9.

I o is pressed, the immediately preceding input is cancelled.

3When setting is completed, press ENTER.The preset requency is tuned in.

nTuner (FM/AM) operationOperation buttons Function

CH +, Preset channel selection

MENU Amp menu

uiop Cursor operationENTER Enter

SEARCH Direct frequency tuning

RETURN B ReturnBAND FM/AM switching

MODE Switch search modes

TUNING df Tuning (up/down)

0 9Preset channel selection (1 8) /

Direct frequency tuning (0 9)

SHIFT Preset channel block selection

MEMORY Preset memory registration

TV Z /X TV power on/standby (Default : SONY)TV INPUT Switch TV input (Default : SONY)

Basicversion

Advanced

version

Inform

ation

Basicversion

BD


32/137

29

Playing a network audioFollow this procedure to play Internet radio stations or music or still

picture (JPEG) fles stored on a computer.


nAbout the internet radio unctionInternet radio reers to radio broadcasts distributed over the

Internet.

Internet radio stations rom around the world can be received.

This unit is equipped with the ollowing Internet radio unctions:Stations can be selected by genre and location.

Up to 56 Internet radio stations can be preset.

Internet radio stations in MP3 and WMA (Windows Media

Audio) ormat can be listened to.

Your avorite radio stations can be registered by accessing an

exclusive DENON Internet radio URL rom a Web browser on

a computer.

The unction is managed or individual users, so you must provide

your MAC or e-mail address.

Exclusive URL: http://www.radiodenon.com

The radio station database service may be suspended without

notice.

This units Internet radio station list is created using a radio

station database service (vTuner). This database service provides

a list edited and created or this unit.

nMedia playerThis unction lets you play music fles and playlists (m3u, wpl)

stored on a computer (media server) connected to this unit via a

network.

With this units network audio playback unction, connection to the

server is possible using one o the technologies below.

Windows Media Player Network Sharing Service

Windows Media DRM10

Album art unctionWhen a WMA (Windows Media Audio), MP3 or MPEG-4 AAC fle

includes album art data, the album art can be displayed while the

music fles are playing.

I you use Ver.11 or later o Windows Media Player, the album art or

WMA fles can be displayed.

Slide show unctionYou can play back image (JPEG) fles that are stored in olders on a

media server and photographs on Flickr as a slideshow.

Also, you can set the time display that is shown during playback

(vpage 104).

This unit plays back image (JPEG) fles in the orientation in which they

are stored in the older.

n Function that simultaneously plays back music and imagefles rom the networkYou can playback music and image fles at the same time by playing

back music fles, and then playing back image fles.

Also, when selecting music fles ater playing back image fles,

press SEARCH when the music playback screen is displayed.Music fles and image fles can be played back simultaneously. At

this time, set Slide Show(vpage 104) in the menu to ON.

Internet Radio

04:01

100%

MEMORY Memory SEARCH Picture View

Now Playing

MP3 32kbps

CH+/- Preset

Title

Radio station

Select

Network contents that can be played back simultaneously are as

ollows.

Music fles: Favorites, Internet Radio, Media Server, USB,

iPod Browse Mode (NET/USB)

Image fles: Media Server, USB, Flickr

GCompatible ormatsHInternet radio Media server z1

WMA (WindowsMedia Audio)

P P

MP3 (MPEG-1 AudioLayer-3)

P P

WAV P

MPEG-4 AAC Pz2

FLAC (Free LosslessAudio Codec)

P

JPEG P

A server or server sotware compatible with distribution in the

corresponding ormats is required to play music fles via a network.

z1 Media serverThis unit is compatible with MP3 ID3-Tag (Ver. 2) standard.

This unit can show the artwork that was embedded by using

MP3 ID3-Tag Ver. 2.3 or 2.4.

This unit is compatible with WMA META tags.

WAV ormat Quantization bit rate: 16 bits

FLAC ormat Quantization bit rate: 16 or 24 bits

z2 Only fles that are not protected by copyright can be played onthis unit.

Content downloaded rom pay sites on the Internet are copyrightprotected. Also, fles encoded in WMA ormat when ripped rom

a CD, etc. on a computer may be copyright protected, depending

on the computers settings.

GCompatible ormatsHSamplingrequency

Bit rate Extension

WMA (WindowsMedia Audio)

32/44.1/48 kHz 48 192 kbps .wma

MP3 (MPEG-1Audio Layer-3)

32/44.1/48 kHz 32 320 kbps .mp3

WAV 32/44.1/48 kHz .wav

MPEG-4 AAC 32/44.1/48 kHz 16 320 kbps

.aac/

.m4a/.mp4

FLAC (FreeLossless Audio

Codec)

32/44.1/48/

88.2/96 kHz .ac

Basicversion

Advanced

version

Inform

ation

Basicversion

vSee overleaf

BD


33/137

30

Playing a network audio

nAbout FlickrFlickr is an online photograph sharing service that started in 2004.

You can use the this unit to view photographs that have been made

public by Flickr users. You do not need an account to use Flickr.

To view photographs that you recorded yoursel, you need an

account in order to upload these photographs to the Flickr server.

For details, see the Flickr homepage.

http://www.ickr.com/

nAbout NapsterNapster is a monthly subscription music distribution service

provided by Napster LLC. This service allows users to download

and play pieces o music they want to hear on this unit. Beore

you can use Napster, you will need to visit the Napster website on

your PC to create an account and register as a member. For detail s,

access the ollowing site:

http://www.napster.com/choose/index_deault.html

nAbout PandoraPandora is an automated music recommendation and Internet

radio service created by the Music Genome Project.

When you frst listen to Pandora, it is necessary to subscribe to a

Pandora account at the Pandora homepage by your PC and register

this machine. See the Pandora homepage or details.

http://www.pandora.com/denon

nAbout RhapsodyRhapsody is a paid music broadcast service o RealNetworks.When you frst listen to Rhapsody, it is necessary to subscribe to

a Rhapsody account at the Rhapsody homepage by your PC and

register this machine. See the Rhapsody homepage or details.

http://www.rhapsody.com/denon

Listening to internet radio

1Prepare for playback.q Check the network environment, then turn on this units

power (vpage 12 Connecting to a home network(LAN)).

w I settings are required, make the Network Connect.

(vpage 91).

2

Press NET/USB to switch the

input source to NET/USB.

3Press ui to select InternetRadio, then press ENTER or p.

Selecting Internet Radio in the Source

Select menu, lets you directly select

Internet Radio.

4Press ui to select the item youwant to play, then press ENTERor p.

5Repeat step 4 until the station list is displayed.The station list is displayed.

6Press ui to select the station, then press ENTER orp.Playback starts once buering reaches 100%.

There are many Internet radio stations on the Internet, and the

quality o the programs they broadcast as well as the bit rate o the

tracks varies widely.

Generally, the higher the bit rate, the higher the sound quality, but

depending on the communication lines and server trafc, the music

or audio signals being streamed may be interrupted. Inversely, lower

bit rates mean a lower sound quality but less tendency or the sound

to be interrupted.

Server Full or Connection Down is displayed i the station is

busy or not broadcasting.

On this unit, older and fle names can be displayed as titles. Any

characters that cannot be displayed are replaced with . (period).



(vpage 83). The deault setting is Mode3.You can speciy the duration o the on-screen display to be displayed

(deault: 30 sec) at menu NET/USB (vpage 96). Press uiop to return to the original screen.When STATUS on the main unit is pressed, the display can be

switched between the title name and radio station name.

nPlaying the last played Internet radio stationSimply press INTERNET RADIOV on the main unit to switchthe input source to Internet Radio and play the last played radio

station.

Press INTERNET RADIO V.The source switches to Internet Radio and

the last played radio station plays.

I INTERNET RADIO V on the main unit is pressed, the sameunction as with the remote control unit can be obtained.

When INTERNET RADIO

Vis pressed, the AMP-operation mode

starts automatically (vpage 105).

Basicversion

Advanced

version

Inform

ation

Basicversion

vSee overleaf

BD
http://-/?-http://-/?-http://-/?-


34/137

31


nRecently played internet radio stationsRecently played internet radio stations can be selected rom

Recently Played.

Up to 20 stations stored in Recently Played.

1Press ui to select RecentlyPlayed, then press ENTER or p.

2Press ui to select the item youwant to play, then press ENTER or

p.

nSearching stations by keyword(Alphabetic strings)

1Press ui to select Search by Keyword, then pressENTER or p.

Station

a

n

0

_

b

o

1

/

c

P

2

:

d

q

3

e

r

4

?

f

s

5

[

g

t

6

\

h

u

7

]

i

v

8

j

w

9

`

k

x

.

{

l

y

@

|

m

z

-

}

Search by Keyword

a/A SPACE INSERT DELETE OK

RETURNInputSelect Cancel

SEARCH 10KeySHIFT a/A

2 Input the characters, then press OK .

For character input, see page 76.

nPresetting internet radio stationsPreset Internet radio stations can be selected directly.

1While the Internet radio station you want to preset is

playing, press MEMORY.

2Press ui to select Preset,then press ENTER.

Internet Radio

00:14100%

MEMORY Memory

CASTING

Now Playing

WMA 63kbp

CH+/- Preset

Favorites

Preset

Select

3Press SHIFT, then press CH +,CH or 1 8 to select the desiredpreset number.

Internet Radio

00:14100%

MEMORY Memory

CASTING

Now Playing

WMA 63kbp

CH+/- Preset

To store preset:

Select A1-G8

Select

SH IFT CH +/- MEMORY

4Press MEMORY again to complete the setting.The Internet radio station is now preset.

n Listening to preset internet radio stationsAfter pressing SHIFT, press CH +,CH or 1 8 to select the registeredpreset number.This unit automatically connects to the

Internet and playback begins.

Registering Internet radio stations to PRESETCHANNEL buttonsUp to three Internet radio stations can be registered to the PRESET

1 3 buttons on the remote control unit or main unit.Recommended Internet radio stations have already been registered

to the PRESET 1 3 buttons.

While the internet radio station you

want to preset is playing, press and

hold PRESET 1 3 for at least 3seconds.The internet radio station is now preset.

NOTE

I registered at a number that has already been preset, the previously

registered setting is cleared.

Basicversion

Advanced

version

Inform

ation

Basicversion

vSee overleaf

BD


35/137

32


Listening to an Internet radio station registered to aPRESET CHANNEL button

Press one of the registered PRESET1 3.

nRegistering internet radio stations as youravoritesFavorites are listed at the top o the menu screen, so when a

station is registered as a avorite it can be tuned in easily.

1Press MEMORY while the Internet radio station youwant to register is playing.

2Press ui to select Favorites,then press ENTER.

Internet Radio

00:14100%

MEMORY Memory

Now Playing

MP3 32kbps

CH+/- Preset

Favorites

Preset

Select

3Press o to select Add.The Internet radio station is registered.

Internet Radio

00:14100%

MEMORY Memory

Now Playing

MP3 32kbps

CH+/- Preset

Add Cancel

Is it registered?

Select

I you do not want to register the station, press p.

n Listening to internet radio stations registered inyour avorites

1Press SOURCE SELECT todisplay the Source Select

menu, then select Favorites

(vpage 21).

2Press ui to select the Internetradio station, then press ENTERor p.This unit automatically connects to the

Internet and playback begins.

nClearing internet radio stations rom youravorites

1Press SOURCE SELECT to display the Source Selectmenu, then select Favorites (vpage 21).

2Press ui to select the Internetradio station you want to clear,

then press MEMORY.

3Press o to select Remove.The selected Internet radio station is

cleared.

Favorites

MEMORY Delete

[2/3]

Radio Algerienne Chaine 1

R

M

CH+/- Preset

Remove Cancel

Is it deleted?

To cancel the operation without clearing the station, press

p.

Basicversion

Advanced

version

Inform

ation

Basicversion

vSee overleaf

BD


36/137

33


n Internet radio operationOperation buttons Function

INTERNET RADIO V Last played internet radio stationPRESET 1 3 Preset channel (1 3) selection

CH +, Preset channel (A1 G8) selection

MENU Amp menu

uiop Cursor operationENTER

(Press and release)Enter

ENTER(Press and hold)

Stop

SEARCH Page searchz1/ Character sortz2

RETURN B Return2 Stop

1 8 Preset channel selection

SHIFT Preset channel block selection

MEMORYFavorites / Preset memory

registration

TV Z /X TV power on/standby (Default :SONY)

TV INPUT Switch TV input (Default : SONY)

z1 When the menu screen is displayed, press SEARCH, then press

o (previous page) or p (next page).To cancel, press ui or SEARCH twice.

z2 When the menu screen is displayed, press SEARCH twice, thenpress op to select the frst letter you want to search mode.I it is not possible to search the list, unsorted list. is displayed.

To cancel, press ui or SEARCH.

I the list is not in alphabetical order, you may not be able to perorm

a character sort.

Basicversion

Advanced

version

Inform

ation

Basicversion

BD


37/137

34


Playing fles stored on a computerUse this procedure to play music fles, image fles or playlists.

1Prepare for playback.q Check the network environment, then turn on this units

power (vpage 12 Connecting to a home network(LAN)).

w I settings are required, make the Network Connect.

(vpage 91).e Prepare the computer (vComputers operating

instructions).

2Press SOURCE SELECT to dis

denon avr-2112ci eng manual

Documents

Denon AVR-1906

DENON AVR control protocol - Denon HEOS -1- DENON AVR control protocol Ver 6.4.0 Application model : AVR-3310/AVR-990/AVC-3310 Revision.6.4.0 Application terminal: RS-232C/ Ethernet

Denon AVR-770SD Use Manual

Denon Avr-1610 Manual

DENON AVR-1404

Denon AVR-800 Manual

Manual Denon Avr-2700 English

Denon AVR-2113.pdf

Denon - AVR-X3000,AVR-S800CI.pdf

DENON AVR control protocolassets.denon.com/DocumentMaster/FR/AVR3313CI... · - 1 - DENON AVR control protocol Ver.01 Application model : AVR-3313CI/AVR-3313 Application terminal:

DENON AVR-1707-OM-E

DENON AVR-1705

AVR-S510BT - Denon

Denon Avr 687lit

Denon AVR-1909 IR codes V01

DENON AVR control protocollogicmachine.net.ru/wp-content/uploads/Resheniya/... · - 1 - DENON AVR control protocol Ver.7.6.0 Application model : AVR-3312CI/AVR-3312 Application terminal:

Denon AVR-1907 Service V02

Denon Avr-2105

Denon AVR-1804_884_AVC-1880

DENON AVR control protocol - awe-europe.com Docs/Denon/Archive/AVR3311CI... · - 1 - DENON AVR control protocol Ver.7.1.0 Application model : AVR-3311CI/AVR-3311/AVR-991 Application

Denon AVR - X1100W.pdf

DENON AVR control protocol - DENON- Enhance the ... - 1 - DENON AVR control protocol Ver. 5.4.0 Application model : AVR-2308CI Application terminal: RS-232C Connector specification

denon avr-1612 _1622

Last Update:Jun. 30. 2 Denon AVR control protocol Ver AVR-S700_S900_X1100_X2100_X3100_X4100_X5200_X7200_PROTOCOL_V06 Control Protocol[1/4] Last Update:Jun. 30. 2 Denon AVR control

Denon AVR-1912

DENON AVR-1400,1420

DENON AVR/AVC control protocol

Denon Avr 1913

Denon AVR 3310 service manual

Denon AVR X4100

Denon AVR-1613,1713,1723

Denon AVR-2400 Manual

Denon AVR-X500

Denon - AVR 3801

denon avr-1400