denon avr1909_avr789_avc1909

of 161/161
D&M Holdings lnc. Copyright 2009 D&M Holdings Inc. All rights reserved. WARNING: Violators will be prosecuted to the maximum extent possible. For purposes of improvement, specifications and design are subject to change without notice. Please use this service manual with referring to the operating instructions without fail. Some illustrations using in this service manual are slightly different from the actual set. 注 意 サービスをおこなう前に、このサービスマニュアルを 必ずお読みください。本機は、火災、感電、けがなど に対する安全性を確保するために、さまざまな配慮を おこなっており、また法的には「電気用品安全法」に もとづき、所定の許可を得て製造されております。 従ってサービスをおこなう際は、これらの安全性が維 持されるよう、このサービスマニュアルに記載されて いる注意事項を必ずお守りください。 本機の仕様は性能改良のため、予告なく変更すること があります。 補修用性能部品の保有期間は、製造打切後 8 年です。 修理の際は、必ず取扱説明書を参照の上、作業を行っ てください。 本文中に使用しているイラストは、説明の都合上現物 と多少異なる場合があります。 SERVICE MANUAL AV SURROUND RECEIVER AV SURROUND AMPLIFIER MODEL JP E3 E2 EK E2A E1C EA AVR-1909 R R AVR-789 R R MODEL JP E3 E2 EK E2A E1C EA AVC-1909 R Ver. 4 Please refer to the MODIFICATION NOTICE. S0017-0V04DM/DG0912

Post on 25-Oct-2014

477 views

Category:

Documents

16 download

Embed Size (px)

DESCRIPTION

Version 4 Service manual

TRANSCRIPT

Ver. 4Please refer to the MODIFICATION NOTICE.

SERVICE MANUALMODEL JP E3 E2 EK E2A E1C EA

AVR-1909 AVR-789AV SURROUND RECEIVERMODEL JP E3 E2 EK E2A E1C EA

AVC-1909AV SURROUND AMPLIFIER

For purposes of improvement, specifications and design are subject to change without notice.

8

Please use this service manual with referring to the operating instructions without fail. Some illustrations using in this service manual are slightly different from the actual set.

D&M Holdings lnc.

S0017-0V04DM/DG0912

Copyright 2009 D&M Holdings Inc. All rights reserved. WARNING: Violators will be prosecuted to the maximum extent possible.

SAFETY PRECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.

LEAKAGE CURRENT CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.

CAUTION

Please heed the points listed below during servicing and inspection. Inspect for safety after servicing!Check that all screws, parts and wires removed or disconnected for servicing have been put back in their original positions, inspect that no parts around the area that has been serviced have been negatively affected, conduct an insulation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety is ensured. (Insulation check procedure) Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and turn the power switch on. Using a 500V insulation resistance tester, check that the insulation resistance between the terminals of the power plug and the externally exposed metal parts (antenna terminal, headphones terminal, microphone terminal, input terminal, etc.) is 1M or greater. If it is less, the set must be inspected and repaired.

Heed the cautions!Spots requiring particular attention when servicing, such as the cabinet, parts, chassis, etc., have cautions indicated on labels or seals. Be sure to heed these cautions and the cautions indicated in the handling instructions.

Caution concerning electric shock!(1) An AC voltage is impressed on this set, so touching internal metal parts when the set is energized could cause electric shock. Take care to avoid electric shock, by for example using an isolating transformer and gloves when servicing while the set is energized, unplugging the power cord when replacing parts, etc. (2)There are high voltage parts inside. Handle with extra care when the set is energized.

Caution concerning disassembly and

assembly!

Though great care is taken when manufacturing parts from sheet metal, there may in some rare cases be burrs on the edges of parts which could cause injury if fingers are moved across them. Use gloves to protect your hands.

CAUTION

Concerning important safety parts

Only use designated parts!The set's parts have specific safety properties (fire resistance, voltage resistance, etc.). For replacement parts, be sure to use parts which have the same properties. In particular, for the important safety parts that are marked z on wiring diagrams and parts lists, be sure to use the designated parts.

Be sure to mount parts and arrange

Many of the electric and structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and using replacement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety performance will be preserved. Parts with safety properties are indicated as shown below on the wiring diagrams and parts lists is this service manual. Be sure to replace them with parts with the designated part number. (1) Schematic diagrams ... Indicated by the z mark. (2) Parts lists ... Indicated by the z mark. Using parts other than the designated parts could result in electric shock, fires or other dangerous situations.

the wires as they were originally!

For safety reasons, some parts use tape, tubes or other insulating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wires inside and clamps are used to keep wires away from heating and high voltage parts, so be sure to set everything back as it was originally.

2 AVR-1909/789, AVC-1909

500V M

(1) (2)

z

(1) z

(2) z

3 AVR-1909/789, AVC-1909

DIMENSIONAVR-1909 model

4 AVR-1909/789, AVC-1909

AVR-789 model

5 AVR-1909/789, AVC-1909

WIRE ARRANGEMENTIf wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation.

Wire arrangement viewed from the top

Back Panel side

Front Panel side

6 AVR-1909/789, AVC-1909

DISASSEMBLY Disassemble in order of the arrow of the figure of following flow. In the case of the re-assembling, assemble it in order of the reverse of the following flow. In the case of the re-assembling, observe "attention of assembling" it. CABINET TOP

PANEL FRONT SUB ASSYRefer to "DISASSEMBLY 1.PANEL FRONT SUB ASSY" and "EXPLODED VIEW" FRONT P.W.B ASSY (Ref. No. of EXPLODED VIEW : BF1) V- AUX P.W.B ASSY (Ref. No. of EXPLODED VIEW : BF2) MIC P.W.B ASSY (Ref. No. of EXPLODED VIEW : BF3) FUNC P.W.B ASSY (Ref. No. of EXPLODED VIEW : BF4) HEAD PHONE P.W.B ASSY (Ref. No. of EXPLODED VIEW : BF6) POWER SW P.W.B ASSY (Ref. No. of EXPLODED VIEW : BF7) ENCORDER P.W.B ASSY (Ref. No. of EXPLODED VIEW : BF8)

HDMI P.W.B ASSYRefer to "DISASSEMBLY 2.HDMI P.W.B ASSY" and "EXPLODED VIEW" HDMI P.W.B ASSY (Ref. No. of EXPLODED VIEW : BH1)

VIDEO P.W.B ASSYRefer to "DISASSEMBLY 6.VIDEO P.W.B ASSY" and "EXPLODED VIEW" VIDEO P.W.B ASSY (Ref. No. of EXPLODED VIEW : BV1)

SIRIUS P.W.B ASSYRefer to "DISASSEMBLY 3.SIRIUS P.W.B ASSY" and "EXPLODED VIEW" SIRIUS P.W.B ASSY (Ref. No. of EXPLODED VIEW : BS1)

INPUT / CPU P.W.B ASSYRefer to "DISASSEMBLY 7.INPUT / CPU P.W.B ASSY" and "EXPLODED VIEW" CPU P.W.B ASSY (Ref. No. of EXPLODED VIEW : BC1) INPUT P.W.B ASSY (Ref. No. of EXPLODED VIEW : BI1)

TUNER PACKRefer to "DISASSEMBLY 4.TUNER PACK" and "EXPLODED VIEW" TUNER PACK (Ref. No. of EXPLODED VIEW : PR1)

MAIN P.W.B SUB ASSYRefer to "DISASSEMBLY 8.MAIN P.W.B SUB ASSY" and "EXPLODED VIEW" MAIN P.W.B ASSY (Ref. No. of EXPLODED VIEW : BM1) 2CH P.W.B ASSY (Ref. No. of EXPLODED VIEW : B21)

TRANSRefer to "DISASSEMBLY 10.TRANS" and "EXPLODED VIEW" TRANS (Ref. No. of EXPLODED VIEW : W8)

CHASSIS BACK SUB ASSYRefer to "DISASSEMBLY 5.CHASSIS BACK SUBASSY" and "EXPLODED VIEW" CHASSIS BACK SUB ASSY (Ref. No. of EXPLODED VIEW : C2) SPEAKER P.W.B ASSY (Ref. No. of EXPLODED VIEW : BF5)

POWER P.W.B SUB ASSYRefer to "DISASSEMBLY 9.POWER P.W.B SUB ASSY" and "EXPLODED VIEW" POWER P.W.B ASSY (Ref. No. of EXPLODED VIEW : BP1) POWER SUPPLY P.W.B ASSY (Ref. No. of EXPLODED VIEW : BP2)

7 AVR-1909/789, AVC-1909

The viewpoint of each photograph (photography direction) Front side ()

Picture A

Top viewPicture C Picture D

Picture B

1. PANEL FRONT SUB ASSYproceeding ( ) : CABINET TOP PANEL FRONT SUB ASSY(1) Remove the screws.

Bottom view

(2) Disconnect the connector wires.

CP541

CORD HOLDER : Loose

CP302

Top view

CP503

cut

CN301

8 AVR-1909/789, AVC-1909

(3) Disconnect the FFC cable.FFC

FFC CABLE

Picture C

CORD HOLDER : Loose(4) Remove the screw.

Top view

(5) Disconnect the connector wire.

Picture C

CN306

Please refer to "EXPLODED VIEW " for the disassembly method of each P.W.B included in PANEL FRONT SUB ASSY . PANEL FRONT SUB ASSY "EXPLODED VIEW "

9 AVR-1909/789, AVC-1909

2. HDMI P.W.B.ASSYproceeding ( ) : CABINET TOP HDMI P.W.B ASSY

(1) Remove the screws.

Picture B

(2) Disconnect the connector wires and boards.

HDMI P.W.B ASSY

CP1007

CP1005

Picture B

Board to board

3. SIRIUS P.W.B ASSYproceeding ( ) : CABINET TOP HDMI P.W.B ASSY SIRIUS P.W.B ASSY(1) Remove the screw.

Picture B

10 AVR-1909/789, AVC-1909

(2) Disconnect the connector wire.

Top view

CP901

SIRIUS ASSY

4. TUNER PACKproceeding ( ) : CABINET TOP HDMI P.W.B ASSY TUNER PACK SIRIUS P.W.B ASSY

(1) Disconnect the FFC cable.FFC

Top view

FFC CABLE(2) Remove the screws.

Picture B

11 AVR-1909/789, AVC-1909

5. CHASSIS BACK SUB ASSYproceeding ( ) : CABINET TOP HDMI P.W.B ASSY TUNER PACK SIRIUS P.W.B ASSY CHASSIS BACK SUB ASSY

(1) Disconnect the connector wires.

CP102B

cut

CP103

Top view

CP103(2) Remove the screws.

CP101

SPEAKER P.W.B ASSY

Picture B

Picture B

SPEAKER P.W.B. ASSYPlease refer to "EXPLODED VIEW " for the disassembly method of each P.W.B included in CHASSIS BACK SUB ASSY . CHASSIS BACK SUB ASSY "EXPLODED VIEW "

12 AVR-1909/789, AVC-1909

6. VIDEO P.W.B ASSYproceeding ( ) : CABINET TOP HDMI P.W.B ASSY TUNER PACK VIDEO P.W.B ASSY SIRIUS P.W.B ASSY CHASSIS BACK SUB ASSY

(1) Disconnect the connector wires and boards.

VIDEO P.W.B ASSY

Board to board

CP2010

Picture D

SUPPORTER

Board to board

CP2008

CP2009

7. INPUT / CPU P.W.B ASSYproceeding ( ) : CABINET TOP HDMI P.W.B ASSY TUNER PACK VIDEO P.W.B ASSY SIRIUS P.W.B ASSY CHASSIS BACK SUB ASSY INPUT / CPU P.W.B ASSY

(1) Disconnect the FFC cable.FFC

CPU P.W.B ASSY

Picture C

FFC CABLE

13 AVR-1909/789, AVC-1909

(2) Disconnect the connector wires and boards.

INPUT P.W.B ASSY

Picture D

CP514

CPU P.W.B ASSY

Board to board

Picture D

INPUT P.W.B ASSY

Board to board

14 AVR-1909/789, AVC-1909

8. MAIN P.W.B SUB ASSYproceeding ( ) : CABINET TOP HDMI P.W.B ASSY TUNER PACK VIDEO P.W.B ASSY SIRIUS P.W.B ASSY CHASSIS BACK SUB ASSY INPUT / CPU P.W.B ASSY

MAIN P.W.B SUB ASSY

Please refer to "EXPLODED VIEW " for the disassembly method of each P.W.B included in MAIN P.W.B ASSY . MAIN P.W.B ASSY "EXPLODED VIEW "

9. POWER P.W.B SUB ASSYproceeding ( ) : CABINET TOP HDMI P.W.B ASSY TUNER PACK SIRIUS P.W.B ASSY CHASSIS BACK SUB ASSY

POWER P.W.B SUB ASSY

(1) Disconnect the connector wires and boards. cut

CP513 CP512

cut

CP504 CP501 CP503 POWER P.W.B ASSY

Picture C POWER SUPPLY P.W.B ASSY

Board to board

Please refer to "EXPLODED VIEW " for the disassembly method of each P.W.B included in POWER P.W.B SUB ASSY. POWER P.W.B SUB ASSY "EXPLODED VIEW "

15 AVR-1909/789, AVC-1909

10. TRANSproceeding ( ) : CABINET TOP TRANS

(1) Disconnect the connector wires. cut

CP2008

cut

CP302

Top view

CP104

CN305

cut

CP513

CP512

cut

CP501

Picture C

Please refer to "EXPLODED VIEW " for the disassembly method of POWER TRANS. POWER TRANS "EXPLODED VIEW "

16 AVR-1909/789, AVC-1909

CAUTION IN SERVICING

Initializing AV SURROUND RECEIVER/AM- AV / PLIFIER AV SURROUND RECEIVER/AMPLIFIER initialization should be performed when the com, peripheral parts of com, and Digital P.W.B. are replaced. 1. Switch off the unit. 2. With the "INPUTMODE" and "SPEAKERS" buttons pressed, press the "ON/OFF" button to turn the power on. 3. Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 buttons and the microprocessor will be initialized. Digital AV / 1. "ON/OFF" OFF 2. "INPUTMODE" "SPEAKERS" 2 "ON/OFF" ON 3. 1 2

Note:If step 3 does not work, start over from step 1. All user settings will be lost and this factory setting will be recovered when this initialization mode. So make sure to m+emorize your setting for restoring after the initialization.

: 3 1

ON/OFF SPEAKERS INPUTMODE

JIG to use for servicingWhen you repair the printing board, you can use the following JIG (Extension cable kit). Please order to Denon Official Service Distributor in your region if necessary. 00D SPK- 561 EXTENSION UNIT KIT : 1 Set 00D SPK- 562 9120 CONN. JOINT KIT : 1 Set

( 00D SPK- 561 EXTENSION UNIT KIT 00D SPK- 562 9120 CONN. JOINT KIT : 1 : 1

When you update the firmware, you can use the following JIG (RS232C to internal connector conversion adapter with RS232C +8P 8P cable kit ). Please order to Denon Official Service Distrib ) utor in your region if necessary. 00DSPK-581 WRITING UNIT : 1 Set 00DSPK-581 WRITING UNIT :1

17 AVR-1909/789, AVC-1909

Check mode for com/DSP versioncom/DSP Version Display Mode1. Operation specificationscom/DSP version display mode: When started up, the version information is displayed. Starting up: E3, EA, JP model With the "DYN VOL" and "VIDEO SELECT" buttons pressed, press the "ON/OFF" button to turn the power on. Now, press the "STATUS" button to the display the 2nd item information on the FL Display. E2 model With the "DYN VOL" and "RDS" buttons pressed, press the "ON/OFF" button to turn the power on. Now, press the "STATUS" button to the display the 2nd item information on the FL Display.

DSP DSP 1. DSP : : E3, EA, JP "DYN VOL" "VIDEO SELECT" 2 "ON/OFF" "STATUS" 2 FL Display E2 "DYN VOL" "RDS" 2 "ON/OFF" "STATUS" 2 FL Display

E3, EA, JP model

E2 model

ON/OFF STATUS

DYN VOL VIDEO SELECT

ON/OFF STATUS

DYN VOL RDS

2. Display OrderDestination information Main-com version information DSP version information

2. DSP

18 AVR-1909/789, AVC-1909

PROCEDURE FOR CHECKING ERRORSDisplaying the protection history1. Operation specificationsERROR MODE(displaying the protection history) When started up, the error information is displayed. Starting up: With the "MENU" and "MULTEQ" buttons pressed, press the "ON/OFF" button to turn the power on. The error (protection history display) mode is set. Now, press the "STATUS" button to turn on the FL display.

ERROR PROTECTION 1. ERROR (PROTECTION ) : ERROR : "MENU" MULTEQ"ON/OFF" ERRORPROTECTION STATUS FL Display

ON/OFF STATUS

MULTEQ

ENTER MENU

ON/OFF STATUS

MULTEQ

ENTER MENU

2.

About the display on the FL displayWhen the "STATUS" button is pressed after setting the error (protection history display) mode, a history like the one shown below is displayed, depending on the conditions. (1) Normally (when there has been no protection incident)Upper Lower P : R N O O T E P C R T O T H E I C S T T O R Y

2. FL Display ERRORPROTECTION STATUS (1) ( PROTECTION ) P : R N O O T E P C R T O T H E I C S T T O R Y

(2) For ASO/DC (when the last protection incident was ASO or DC protection)Upper Lower P : R A O S T O E / C D T C H I S T O R Y

(2) ASO/DC ( PROTECTION ASO DC PROTECTION ) P : R A O S T O E / C D T C H I S T O R Y

(3) For THERMAL (when the last protection incident was THERMALprotection)Upper Lower P : R T O H T E E R C M T A L H I S T O R Y

(3) THERMAL ( PROTECTION THERMAL PROTECTION ) P : R T O H T E E R C M T A L H I S T O R Y

When the "STATUS" button is pressed again after the above protection history is displayed, the normal display reappears. PROTECTION STATUS

19 AVR-1909/789, AVC-1909

3.

Clearing the protection historyThere are two ways to clear the protection history, as described below. (1) Start up the error (protection display) mode, display the error, then press and hold in the "ENTER" button for 3 seconds.Upper Lower P : R T O H T E E R C M T A L H I S T O R Y

3. PROTECTION PROTECTION (1) ERROR(PROTECTION ) ERROR ENTER P : R T O H T E E R C M T A L H I S T O R Y

Press and hold in the "ENTER" button for 3 secondsUpper Lower P R O T E C C L T E A H R I S T O R Y

ENTER 3 P R O T E C C L T E A I S T O R Y

H R

The above is displayed and the protection history is cleared.Upper Lower P : R N O O T E P C R T O T H E I C S T T O R Y P : R N O O T E P

PROTECTION C R T O T I C S T T O R Y

H E

(2) Initialize. If you want to save a backup, use the method in 3.(1) above. (2). 3.(1)

Warning indication by the STANDBY LEDIf the power is turned off when a protection incident has been detected, the STANDBY LED (red) flashes as follows as warning according to the conditions in which the protection incident occurred. (1) ASO/DC PROTECTION : Flashes in cycles of 0.5 seconds (0.25 seconds lit, 0.25 seconds off) (2) THERMAL PROTECTION : Flashes in cycles of 2 seconds (1 second lit, 1 second off)

STANDBY LED PROTECTION POWER OFF PROTECTION STANDBY LED( ) (1) ASO/DC PROTECTION 0.5 0.25 /0.25 (2) THERMAL PROTECTION2 1 /

20 AVR-1909/789, AVC-1909

ADJUSTMENTAudio SectionIdling CurrentRequired measurement equipment: DC Voltmeter

:DC Voltmeter

1. Preparation(1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature 15 C ~ 30 C (59 F ~ 86 F). (2) Presetting POWER (Power source switch) OFF SPEAKER (Speaker terminal) No load (Do not connect speaker, dummy resistor, etc.)

1. (1) 15 30 (2) OFF ( )

2. Adjustment(1) Remove top cover and set VR101 FL, FR, C, SL, SR, on Main Amp. Unit, VR401, VR402 on 2ch- Amp. Unit at fully counterclockwise (c) position. (2) Connect DC Voltmeter to test points (FRONT-Lch: TP101, FRONT-Rch: TP105, CENTER ch: TP103, SURROUND-Lch: TP102, SURROUND-Rch: TP104, SURROUND-BACK Lch: TP401, SURROUND-BACK Rch: TP402). (3) Connect power cord to AC Line, and turn power switch "ON". (4) Presetting. MASTER VOLUME : "---" counterclockwise (c min.) SPEAKER (Speaker terminal) : No load (Do not connect speaker, dummy resistor, etc.) MODE : 7CH STEREO (5CH STEREO) FUNCTION : CD (5) Within 2 minutes after the power on, turn VR101 clockwise (x) to adjust the TEST POINT voltage to 1.5 mV 0.5 mV DC. (6) After 10 minutes from the preset above, turn VR101 to set the voltage to 2.0 mV 0.5 mV DC. (7) Adjust the Variable Resistors of other channels in the same way.

2. (1) VR101 FL, FR, C, SL, SR 2ch- VR401,VR402 (c) (2) (FRONT-Lch: TP101, FRONT- Rch: TP105, CENTER ch: TP103, SURROUND-Lch: TP102, SURROUND-Rch: TP104, SURROUND-BACK Lch: TP401, SURROUND-BACK Rch: TP402) DC Voltmeter (3) AC100V95 105V "ON" (4) ON MASTER VOLUME (c) SPEAKER MODE : 7CH STEREO (5CH STEREO) FUNCTION : CD (5) 2 VR101 (x) 1.5mV 0.5mV DC (6) 10 VR101 2.0mV 0.5mV DC (7)

MAIN AMP. UNIT

DC VoltmeterF Lch S Lch C ch S Rch F Rch

VR101FL

VR101SL TP101 TP102

VR101C

VR101SR

VR101FR

2CH AMP. UNIT

TP103

TP104

TP105

VR401 TP401

VR402 TP402

S Back Lch

S Back Rch

21 AVR-1909/789, AVC-1909

---MEMO---

22 AVR-1909/789, AVC-1909

TROUBLE SHOOTING1. POWER1.1. Power not turn onPower not turn on

1. 1.1.

Is the ON/STANDBY indicator on the front panel flashing red?

YES

Are there any incomplete connections in the connectors connecting between the various circuit boards? YES Connect the connectors properly.

NO

Is there a short circuit between the speaker terminals and the ground? NO Check for damage in the power amplifier circuitry parts and replace any defective parts.

YES

Correct the short circuit between the speaker and the ground.

/

YES

YES

NO

SP GND

YES

SP GND

NO POWER AMP

NO

NO

Is the fuse blown? YES

NO

Refer to Fuse is blown

YES

NO

Does the power turn on when the POWER switch is turned off then back on?

NO

Is a DC 6V voltage being supplied from the POWER UNIT (CN505 pins 4, 5) to the microprocessor? YES

NO

Is a DC 6V voltage output when the cord supplying the power from the SUPPLY UNIT to the microprocessor (CP514) is unplugged? YES Check the circuitry and parts from CP514 on the SUPPLY UNIT to the microprocessor for damage and short-circuits, and replace any defective parts.

NO

Check the parts from IC501 to the primary circuitry and replace any defective parts.

POWER SW OFF POWER SW ON YES POWER SW 1 ( )

NO

POWER CN505 4, 5 DC6V YES

NO

SUPPLY CP514 DC6V YES SUPPLY CP514

NO

IC501 1

YES Check the primary circuitry parts including the POWER switch (for poor contacts, etc.), and replace any defective parts.

Check the microprocessor periphery circuitry and replace any defective parts.

1.2. Fuse is blownFuse is blown

1.2.

Check for leaks or short circuits in the primary side parts, and replace any defective parts.

Check for short circuits in the rectifier diodes and circuitry of the secondary side rectifying circuits, and replace any defective parts.

Check for short circuits in the power stabilizer unit's regulator output terminal and the ground, and replace any defective parts.

1

2

GND

FUSE After repairing, also replace the fuse.

23 AVR-1909/789, AVC-1909

2. Analog video2.1. Monitor out & VCR outMONITOR OUT (CVBS/S/COMPONENT) output NG When checking operation, select DVD for the function. (COMPONENT1 input)

2. 2.1. Monitor out & VCR outMONITOR OUT (CVBS/S/COMPONENT) NG DVD (COMPONENT1 )

Checking the video convert ON/OFF settings

ON/OFF

Video convert ON

ON

Input CVBS

Input S

Input COMPONENT

CVBS

S

COMPONENT

A

Interlace or Progressive

A

or

Interlace

B

Progressive no output

B

VCR MONITOR OUT (CVBS/S) Output NG

When checking operation, select DVD for the function.

VCR MONITOR OUT (CVBS/S) NG

DVD

Input CVBS

Input S

CVBS

S

C C

24 AVR-1909/789, AVC-1909

AInput CVBS/S

A CVBS/S

Check power supply voltage VIDEO UNIT +5V : CN2005-8pin -5V : CN2005-7pin MC_+5V : CN2001-5pin OK Check input of HDMI UNIT video decoder signal. Input V : C1272 Input Y : C1270 Input C : C1274

Check power supply voltage HDMI UNIT +3.3V : IC1015-O,IC1017-IN +1.8V : IC1016,IC1017-O

NG

To troubleshooting 1.1 Power not turn on.

VIDEO +5VCN2005-8pin -5VCN2005-7pin MC_+5VCN2001-5pin OK

HDMI +3.3VIC1015-O,IC1017-IN +1.8VIC1016,IC1017-O

NG

1.1

NG

Check VIDEO CNT UNIT signal DET. V : CP1006-11pin : H(+5V) Y : CP1006-10pin : H(+5V)

NG

Check input of input selector and Video AMP, surrounding circuitry soldering. Input : IC2002,IC2003,IC2004 Video AMP : IC2008,IC2001,IC2005 or CPU UNIT flaw.

HDMI Video Decoder VC1272 YC1270 CC1274

NG

VIDEO CNT DET VCP1006-11pin H(+5V) YCP1006-10pinH(+5V) OK

NG

IC2002,IC2003,IC2004 IC2008,IC2001,IC2005 CPU

OK OK Check soldering of VIDEO CNT UNIT connector base, and check poor contacts. OK

VIDEO CNT

Check output of driver(IC1018) after HDMI UNIT video encoder. OutputV : CN1008 7pin OutputY : CN1008 11pin Output C : CN1008 9pin Output Y : CN1009 9pin Output Cb : CN1009 11pin Output Cr : CN1009 13pin

NG

Check output of after HDMI UNIT video encoder. OutputY : C1245 -side Output C : C1243 Output Y : C1257 -side Output Cb : C1260 -side Output Cr : C1265 -side OK

NG

Check input of HDMI UNIT Video Decoder(IC1020)/ Encoder(IC1019) and surrounding circuitry soldering. or CPU UNIT flaw.

HDMI Video Encoder (IC1018) VCN1008 7pin YCN1008 11pin CCN1008 9pin YCN1009 9pin CbCN1009 11pin CrCN1009 13pin

NG

HDMI Video Encoder YC1245 - CC1243 YC1257 - CbC1260 - CrC1265- OK

NG

HDMI Video Decoder(IC1020)/ Encoder(IC1019) CPU

OK

Check soldering of IC1015 and surrounding parts. CVBS/S

OK

IC1015 COMPONENT NG VIDEO CNT IC2014,IC2015

CVBS/S output Check output of AMP. Output V : IC2016-24pin Output Y : IC2016-20pin Output C : IC2016-22pin OK Check cable between main unit and monitor or Check monitor. Check input of input selector and surrounding circuitry soldering. Input : IC2023 or CPU UNIT flaw. Check input of AMP Input Y : C2123 +side Input Cb : C2131 +side Input Cr : C2136 +side OK Check soldering of IC2022 and surrounding parts. Check soldering of output selector and surrounding circuitry. Check soldering of VIDEO CNT UNIT connector base. Output : IC2014,IC2015

COMPONENT output

NG

AMP VIC2016-24pin YIC2016-20pin CIC2016-22pin OK -MONITOR MONITOR

NG

NG

Check output of AMP Output Y : IC2022-13pin Output Cb : IC2022-11pin Output Cr : IC2022-9pin OK Check cable between main unit and monitor or Check monitor.

:IC2023 CPU

NG

AMP YC2123 + CbC2131 + CrC2136 + OK IC2022

NG

AMP VIC2022-13pin CbIC2022-11pin CrIC2022-9pin OK -MONITOR MONITOR

VIDEO

Unless specified, VIDEO UNIT part.

25 AVR-1909/789, AVC-1909

BInput COMPONENT

B COMPONENT

Check power supply voltage VIDEO UNIT +5V : CN2005-8pin -5V : CN2005-7pin MC_+5V : CN2001-5pin OK Check input of HDMI UNIT video decoder signal. Input V : C1281 Input Y : C1273 Input C : C1271

Check power supply voltage HDMI UNIT +9V : CN2005-9pin +3.3 : IC1015-O,IC1017-IN +1.8V : IC1016,IC1017-O

NG

To troubleshooting 1.1 Power not turn on.

VIDEO +5V : CN2005-8pin -5V : CN2005-7pin MC_+5V : CN2001-5pin OK

HDMI +9V : CN2005-9pin +3.3 V : IC1015-O,IC1017-IN +1.8V : IC1016,IC1017-O

NG

1.1

NG

Check VIDEO CNT UNIT signal DET. Y : CP1006-12pin : H(+5V)

NG

Check input of input selector and Video AMP, surrounding circuitry soldering. Input : IC2023 Video AMP : IC2021 or CPU UNIT flaw.

HDMI Video Decoder V : C1281 Y : C1273 C : 1271

NG

VIDEO CNT DET YCP1006-12pinH(+5V)

NG

C2023 C2021 CPU

OK OK Check soldering of VIDEO CNT UNIT connector base, and check poor contacts. OK

OK VIDEO CNT

Check output of driver(IC1018) after HDMI UNIT video encoder. OutputV : CN1008 7pin OutputY : CN1008 11pin Output C :CN1008 9pin Output Y: CN1009 9pin Output Cb : CN1009 11pin Output Cr : CN1009 13pin

NG

Check output of after HDMI UNIT video encoder. OutputY : C1245 -side Output C : C1243 Output Y: C1257 -side Output Cb : C1260 -side Output Cr : C1265 -side OK

NG

Check input of HDMI UNIT Video Decoder(IC1020)/ Encoder(IC1019) and surrounding circuitry soldering. or CPU UNIT flaw.

HDMI Video Encoder (IC1018) VCN1008 7pin YCN1008 11pin CCN1008 9pin YCN1009 9pin CbCN1009 11pin CrCN1009 13pin

NG

HDMI Video Encoder YC1245 - CC1243 YC1257 - CbC1260 - CrC1265- OK

NG

HDMI Video Decoder(IC1020)/ Encoder(IC1019) CPU

OK

Check soldering of IC1015 and surrounding parts. CVBS/S

OK

IC1015 COMPONENT NG VIDEO CNT IC2014,IC2015

CVBS/S output Check output of AMP Output V : IC2016-24pin Output Y : IC2016-20pin Output C : IC2016-22pin OK Check cable between main unit and monitor or Check monitor. Check input of input selector and surrounding circuitry soldering. Check soldering of VIDEO CNT UNIT connector base. Input : IC2023 or CPU UNIT flaw. Check soldering of output selector and surrounding circuitry. Check soldering of VIDEO CNT UNIT connector base. Output : IC2014,IC2015

COMPONENT output

NG

AMP VIC2016-24pin YIC2016-20pin CIC2016-22pin OK -MONITOR MONITOR

NG

Check input of AMP Input Y : C2123 +side Input Cb : C2131 +side Input Cr : C2136 +side OK Check soldering of IC2022 and surrounding parts.

NG

Check output of AMP Output Y : IC2022-13pin Output Cb : IC2022-11pin Output Cr : IC2022-9pin OK Check cable between main unit and monitor or Check monitor.

VIDEO CNT :IC2023 CPU UNIT

NG

AMP YC2123 + CbC2131 + CrC2136 + OK IC2022

NG

AMP VIC2022-13pin CbIC2022-11pin CrIC2022-9pin OK -MONITOR MONITOR

VIDEO

Unless specified, VIDEO UNIT part.

26 AVR-1909/789, AVC-1909

CInput CVBS/S

C CVBS/S

Check power supply voltage +5V : CN2005-8pin -5V : CN2005-7pin MC_+5V : CN2001-5pin OK Check output of AMP Output V : IC2016-33pin Output Y : IC2016-31pin Output C : IC2016-29pin OK Check cable between main unit and monitor or Check monitor.

NG

To troubleshooting 1.1 Power not turn on.

+5V : CN2005-8pin -5V : CN2005-7pin MC_+5V : CN2001-5pin OK

NG

1.1

NG

Check VCRINH INH : CP2002-10pin : H(+5V)

NG

Check soldering of VIDEO CNT UNIT connector base, and check poor contacts.

AMP V : IC2016-33pin Y : IC2016-31pin C : IC2016-29pin OK

NG

VCRINH INHCP2002-10pinH(+5V) OK : IC2009,IC2010,IC2011

NG

VIDEO CNT

Check input of input selector and surrounding circuitry soldering. Input : IC2009,IC2010,IC2011

-MONITOR MONITOR

Unless specified, VIDEO UNIT part.

VIDEO

27 AVR-1909/789, AVC-1909

2.2. HDMI outHDMI OUT output NG When checking operation, select DVD for the function. (COMPONENT1 input)

2.2. HDMI outHDMI OUT NG DVD (COMPONENT1 )

Checking the video convert ON/OFF settings

ON/OFF

Video convert ON

ON

Input CVBS

Input S

Input COMPONENT

Input HDMI

CVBS

S

COMPONENT

HDMI

D

To troubleshooting of HDMI/DVI

D

HDMI/DVI

Input 1080p?

YES

No output

1080p ?

YES

E

E

28 AVR-1909/789, AVC-1909

DInput CVBS/S

D CVBS/S

Check power supply voltage +5V : CN2005-8pin -5V : CN2005-7pin MC_+5V : CN2001-5pin OK Check input of HDMI UNIT video decoder signal. Input V : C1272 Input Y : C1270 Input C : C1274

Check power supply voltage +3.3 : IC1015-O,IC1017-IN +1.8V : IC1016,IC1017-O

NG

To troubleshooting 1.1 Power not turn on.

+5V : CN2005-8pin -5V : CN2005-7pin MC_+5V : CN2001-5pin OK

+3.3 V : IC1015-O,IC1017-IN +1.8V : IC1016,IC1017-O

NG

1.1

NG

Check VIDEO CNT UNIT signal DET. V : CP1006-11pin : H(+5V) Y : CP1006-12pin : H(+5V)

NG

Check input of input selector and Video AMP, surrounding circuitry soldering. Input : IC2002,IC2003,IC2004 Video AMP : IC2008,IC2001,IC2005 or CPU UNIT flaw.

HDMI Video Decoder V : C1272 Y : C1270 C : C1274

NG

VIDEO CNT DET VCP1006-11pinH(+5V) YCP1006-10pinH(+5V) OK

NG

IC2002,IC2003,IC2004 IC2008,IC2001,IC2005 CPU

OK OK Check soldering of VIDEO CNT UNIT connector base, and check poor contacts. OK

VIDEO CNT

HDMI/DVI To troubleshooting of HDMI/DVI

Unless specified, VIDEO UNIT part.

VIDEO

EInput COMPONENT

E COMPONENT

Check power supply voltage +5V : CN2005-8pin -5V : CN2005-7pin MC_+5V : CN2001-5pin OK Check input of HDMI UNIT video decoder signal. Input Y : C1281 Input Cb : C1273 Input Cr : C1271

Check power supply voltage +9V : CN2005-9pin +3.3 : IC1015-O,IC1017-IN +1.8V : IC1016,IC1017-O

NG

To troubleshooting 1.1 Power not turn on.

+5V : CN2005-8pin -5V : CN2005-7pin MC_+5V : CN2001-5pin OK

+9V : CN2005-9pin +3.3 V : IC1015-O,IC1017-IN +1.8V : IC1016,IC1017-O

NG

1.1

NG

Check VIDEO CNT UNIT signal DET. Y : CP1006-12pin : H(+5V)

NG

Check input of input selector and Video AMP, surrounding circuitry soldering. Input : IC2023 Video AMP : IC2021 or CPU UNIT flaw.

HDMI Video Decoder Y : C1281 Cb : C1273 Cr : 1271

NG

VIDEO CNT DET YCP1006-12pinH(+5V)

NG

IC2023 IC2021 CPU

OK OK Check soldering of VIDEO CNT UNIT connector base, and check poor contacts. OK

OK VIDEO CNT

HDMI/DVI To troubleshooting of HDMI/DVI

VIDEO Unless specified, VIDEO UNIT part.

29 AVR-1909/789, AVC-1909

3. HDMI/DVI3.1. No picture or sound is outputNo picture or sound is output YES Check the HDMI/DVI cable connection YES Is the HDMI/DVI connected? YES Are you using an HDMI/DVI selector, repeater or a device for improving picture quality? NO Are you using a certified HDMI cable (one with the HDMI stamp)? YES Are you using an HDMI/DVI cable less than 5 meters in length? YES Are the picture and sound output when another HDMI/DVI cable is used? NO Checking the DVD player YES Is the DVD player's HDMI output setting correct? YES When using a DENON DVD player, is the fluorescent display tube's "HDMI" indicator lit? If using a non-DENON DVD player, proceed to "YES". YES Are the picture and sound output when the DVD player's resolution is changed? NO Is sound output from the set's speaker terminals when the TV's power is turned off or the connection cable between the TV and the set is disconnected? NO Are the picture and sound output when a different DVD player is used? NO YES The DVD player is defective. YES The DVD player may not be compatible with HDCP repeaters. Ask the DVD player's manufacturer. YES Set the DVD player's output resolution to a resolution with which the TV is compatible. YES Check the HDMI output setting, referring to the DVD player's operating instructions. YES The HDMI/DVI cable is defective. NO Replace the HDMI/DVI cable with one that is less than 5 meters in length (2 meters recommended) to check. NO Use a certified HDMI cable (one with the HDMI stamp). YES Disconnect everything and connect only the HDMI/DVI cable to check. cable properly NO There may be a problem with the HDMI/ DVI cable. Check the connection.

3. HDMI/DVI3.1. YES HDMI/DVI YES HDMI/DVI YES HDMI/DVI NO HDMI HDMI HDMI YES HDMI/DVI 5m YES HDMI/DVI NO DVD YES DVD HDMI YES DENON DVD FL "HDMI" DVD "YES" YES NO DVD NO DVD HDCP DVD YES DVD TV NO DVD HDMI YES HDMI/DVI NO HDMI/DVI 5m ( ) NO HDMI HDMI HDMI YES HDMI/DVI NO HDMI/DVI

NO

TV TV

YES

NO DVD NO YES DVD

30 AVR-1909/789, AVC-1909

Check the TV

TV

Is the TV HDCP-compatible? YES

NO

Use an HDCP-compatible TV. PC TVs cannot be used.

TV HDCP

NO

HDCP TV TV PC

YES NO If the TV is not compatible with resolutions of 1080P, no picture will be output, even if the DVD player's resolution is set to 1080P. TV 1080P DVD 1080P

Is the TV compatible with resolutions of 1080P?

TV 1080P

NO

YES Is the TV's input set to HDMI? YES Are the picture and sound output when a different TV is used? YES Check the set NO The TV is defective. NO Check the TV's input setting, referring to the TV's operating instructions.

YES TV HDMI YES TV YES NO TV NO TV

Is the set's input set to HDMI? YES Is the TV information properly displayed on the "Monitor info." display menu? YES NO YES The set does not recognize the TV. Is IC1009 pin 51 "H" (3V-5V)? With the TV connected, check the voltage of the IC on the side on which the TV is connected. YES

NO

Check the set's input setting, referring to the set's operating instructions.

HDMI YES

NO

NO

The pattern and circuit from the HDMI connector (JK1004) to the IC (IC1009) is defective.

Monitor info. TV

NO

TV IC1009 51pin "H"(3V-5V) TV TV IC YES

NO

HDMI (JK1004) IC(IC1009)

Does the set's wallpaper image appear on the TV when the HDMI/DVI cable between the DVD player and the set is disconnected?

NO

Are the picture and sound output from other Monitor Out terminals (VIDEO out, S-VIDEO out or Component out)?

YES

The HDMI output circuitry is defective. (IC1009/IC1010 and surrounding circuitry)

YES

DVD HDMI/DVI TV

NO

Monitor Out(VIDEO out/S-VIDEO out/Component out) NO

YES

HDMI (IC1009/IC1010 )

YES When using a DENON DVD player, is the fluorescent display tube's "HDMI" indicator lit? If using a nonDENON DVD player, proceed to "NO". YES

YES The DVD player does not recognize the connection with the set. Is the HDMI connector (JK1001/JK1002/ IC1003) pin 19 "H" (5V)? With the DVD player connected, check the voltage of the HDMI connector for the input on the side on which the DVD player is connected. YES

NO

YES DVD HDMI (JK1001/JK1002/ JK1003) 19pin "H"(5V) DVD DVD HDMI YES

NO

NO

The pattern and circuit from the HDMI connector (JK1001/JK1002/IC1003) to the IC1045 is defective.

DENON DVD FL "HDMI" DVD "NO"

NO

NO

HDMI (JK1001/JK1002/ JK1003) IC1045

YES HDMI (IC1002/IC1008/IC1010 )

The HDMI output circuitry is defective. (IC1002/IC1008/IC1010 and surrounding circuitry)

31 AVR-1909/789, AVC-1909

BLOCK DIAGRAMAUDIO BLOCK DIAGRAM

32 AVR-1909/789, AVC-1909

VIDEO BLOCK DIAGRAM

AVR-1909 VIDEO BLOCK DIAGRAM DIGITAL VIDEOAudio

HDMI IC1009 TRANSMITTER SiI9134 AtoH CONVERT specification1.480i 480i/480p/1080i60Hz/720p60Hz/1080p60Hz 2.576i 576i/576p/1080i50Hz/720p50Hz/1080p50Hz 3.480p 1080i60Hz/720p60Hz/1080p60Hz 4.576p 1080i50Hz/720p50Hz/1080p50Hz 5.1080i60Hz/720p60Hz 1080p60Hz 6.1080i50Hz/720p50Hz 1080p50Hz75 LOAD 75 LOAD 75 LOAD 75 LOAD 75 LOAD 75 LOAD -6dB -6dB -6dB -6dB -6dB -7.7dB

HDMI-1

IC1002 HDMI SW SiI9185

IC1008 RECEIVER SiI9135

Video

HDMI -2

I2s

PS/HD:YCBCR4:2:2 16bit PS/HD:YCBCR4:2:2 16bit SD:ITU-R656 8bitINPUT:1.0Vpp INPUT:0.7Vpp

To DSP

HDMI -3SPDIF

IC1011 I/P SCALER FLI2310 DAC D6dB

1000u

To DIR

IC1020INPUT:0.7Vpp INPUT:1.0Vpp INPUT:0.286Vp INPUT:0.82Vpp 70

DAC E IC1019 VIDEO ENCODER ADV7172 DAC F DAC B DAC C

IC1018 FILTER internal VIDEO DRIVERINPUT:1Vpp

VIDEO DECODER ADV7401

BH7868FS

70

VIDEO CONVERT BLOCK

70

D CONTROL IN (JAPAN ONLY)

COMPONENTSD:ITU-R656 ONLY IC2027, IC2026 INPUT SELECTOR SIGNAL DET.

D CONTROL OUT (JAPAN ONLY)

LINE3 DC GENERATOR COMPONENT/D IN75 LOAD 75 LOAD 75 LOAD 75 LOAD 75 LOAD 75 LOAD -6dB -6dB

INTERNAL GAIN:0dB

6dB 6dB 6dB

IC2021NJM2581

IC2023-6dB -6dB -6dB -6dB

INPUT SELECTOR NJW1321

6dB 6dB 6dB

IC2022NJM2581

COMPONENT OUT

S(Y/C) IN75 LOAD 75 LOAD -6dB -6dB

S-VIDEOIC2002/IC200 3

SIGNAL DET.IC20016dB

OSD BLOCK

IC2012 IC20080dB

INPUT SELE CTOR

0dB

INPUT MUTE

IC2005

6dB

IC2007

SYNC. DET.IC2009/2010

0dB 0dB

IC2001INPUT:2Vpp

IC20070dB

REC SELE CTOR

IC2005

S MONI.DET.0dB

S(Y/C) RECOUT6dB 6dB

INPUT MUTE

70

IC2017 OSDINPUT:2Vpp

IC2014 IC20130dB 330 LOAD -6dB 6dB

S(Y/C) OUT

IC2016 RECOUT BUFFER/INH

IC2007

IC2018 IC2008330 LOAD -6dB

IC20166dB

CVBS IN-6dB 75 LOAD

CONPOSITEIC2004 INPUT INPUT SELE SELECTOR CTOR IC2008INPUT MUTE

SIGNAL DET.6dB

IC20080dB 330 LOAD 330 LOAD -6dB -6dB

REC SELE CTOR

IC2011

IC2015

IC2016

CVBS OUT6dB

INPUT MUTE

CVBS RECOUT6dB

IC2016 RECOUT BUFFER/INH

33 AVR-1909/789, AVC-1909

LEVEL DIAGRAMS (1/5)FRONT LEVEL DIAGRAM

AVR-1909 LEVEL DIAGRAM FRONT ch

R2A15215FPANALOG ATT H/POUT

LINE IN

SPEAKER OUT

ADAU1328A/D D/A D/A OUT MUTE

GAIN ADJ.

FROM SWch TO Surround Back (ZONE2 MODE)

DSP

RECOUT

EXT IN

+30dB 3.876V NON CLICP MAX SIGNAL LEVEL 4.0Vrms SP OUT 3.99Vrms/8 +20dB ADAU1328 0dBFS +10dB -35dB -10dBFS 200mV 0dB LINE IN/EXT IN -8dB -20dBFS A/D IN 79.4mVrms -20dBFS(DIG.IN) PCM or DD Config1 -22dBFS(A/D IN) -20dBFS -10dB H/POUT 71.0mVrms +7dB -2+2=0dB -2+6.5=4.5dB Config2 DOLBY LIMIT LEVEL 1.41 Vrms (ALLch-3dBFS) -2dB RECOUT 0dB 0dBFS 0.88Vrms 0dBFS Config1 DOLBY LIMIT LEVEL (ALLch-3dBFS) +28dB SUM FROM SWch +10dB +20dB

-10dBFS

-10dB

-26.5dBFS(DIG.IN) DD Config2 -30dBFS -20dB -30dBFS

-20dB

-40dBFS -30dB

-40dBFS -30dB

-40dB

-40dB

34 AVR-1909/789, AVC-1909

LEVEL DIAGRAMS (2/5)CENTER LEVEL DIAGRAM

AVR-1909 LEVEL DIAGRAM CENTER ch

R2A15215FP

SPEAKER OUT

ADAU1328A/D D/A D/A OUT MUTE

GAIN ADJ.

DSP

EXT IN

+30dB NON CLICP MAX SIGNAL LEVEL 4.0Vrms SP OUT 3.99Vrms/8 +20dB 0dBFS 0.88Vrms 0dBFS +10dB Config2 DOLBY LIMIT LEVEL (ALLch-3dBFS) +10dB Config1 DOLBY LIMIT LEVEL (ALLch-3dBFS) +20dB +29dB

-10dBFS 200mV 0dB LINE IN/EXT IN -20dBFS(DIG.IN) PCM or DD Config1 -22dBFS(A/D IN) -20dBFS -10dB -26.5dBFS(DIG.IN) DD Config2 -30dBFS -20dB +7dB -2+2=0dB

-2dB 0dB

-2+6.5=4.5dB

-10dB

-20dB

-40dBFS -30dB -30dB

-40dB

-40dB

35 AVR-1909/789, AVC-1909

LEVEL DIAGRAMS (3/5)SUB WOOFER LEVEL DIAGRAM

AVR-1909 LEVEL DIAGRAM SUBWOOFER ch

R2A15215FP

MUTE GAIN ADJ. A/D ADAU1328 PLD D/A ADAU1328 D/A OUT MUTE

PREOUT

DSP

EXT IN

Config2 3.876V

DOLBY LIMIT LEVEL (ALLch-3dBFS) SUM to FRONTch NON CLICP MAX SIGNAL LEVEL 4.0Vrms

+30dB

Config1 +20dB 0dBFS 0.88Vrms 0dBFS +10dB

DOLBY LIMIT LEVEL

(ALLch-3dBFS) +20dB

+10dB

-10dBFS 200mV 0dB LINE IN/EXT IN

-2dB

PREOUT 317mVrms 0dB PREOUT 159mVrms

-20dBFS -10dB -34dBFS(PCM.IN) -36dBFS(A/D IN) -30dBFS -20dB -40dBFS(DIG.IN) DD Config1 -40dBFS -30dB -46.5dBFS(DIG.IN) DD Config2 -50dBFS -40dB +7dB +6dB +3dB SUM to FRONT-ch

-2+(20-6)=12dB -10dB

-20dB

-30dB

-40dB

36 AVR-1909/789, AVC-1909

LEVEL DIAGRAMS (4/5)SURROUND LEVEL DIAGRAM

AVR-1909 LEVEL DIAGRAM SURROUND ch

R2A15215FP

SPEAKER OUT

ADAU1328A/D D/A D/A OUT MUTE

GAIN ADJ.

DSP

EXT IN

+30dB NON CLICP MAX SIGNAL LEVEL 4.0Vrms Config1 +20dB 0dBFS 0.88Vrms Config2 0dBFS +10dB +10dB DOLBY LIMIT LEVEL 1.41 Vrms (ALLch-3dBFS) +28dB DOLBY LIMIT LEVEL 1.41 Vrms (ALLch-3dBFS) SP OUT 3.99Vrms/8 +20dB

-10dBFS 200mV 0dB LINE IN/EXT IN -23dBFS(DIG.IN) PCM or DD Config1 -25dBFS(A/D IN) -20dBFS -10dB -29.5dBFS(DIG.IN) DD Config2 -30dBFS -20dB -2+2=0dB +10dB

-2dB 0dB

-2+6.5=4.5dB -10dB

-20dB

-40dBFS -30dB -30dB

-40dB

-40dB

37 AVR-1909/789, AVC-1909

LEVEL DIAGRAMS (5/5)SURROUND BACK LEVEL DIAGRAM

AVR-1909 LEVEL DIAGRAM SURR.BACK ch

R2A15215FP

SPEAKER OUT

ADAU1328A/D D/A D/A OUT MUTE

GAIN ADJ.

DSP

EXT IN

+30dB NON CLICP MAX SIGNAL LEVEL 4.0Vrms SP OUT 3.99Vrms/8 SP OUT(D/A OUT) 2.82Vrms/8 +20dB

+20dB 0dBFS 0.88Vrms

Config1

DOLBY LIMIT LEVEL 1.41 Vrms (ALLch-3dBFS)

+26dB 0dBFS +10dB +10dB

-10dBFS 200mV 0dB LINE IN/EXT IN

Config2

DOLBY LIMIT LEVEL 1.41 Vrms(ALLch-3dBFS) -2dB 0dB

+7dB -20dBFS -25dBFS(A/D IN) -26dBFS(DIG.IN) DD EX Config1 -30dBFS -32.5dBFS(DIG.IN) DD EX Config2

-2+3+2=+3dB -2+3=1dB -2+6.5+3=7.5dB -10dB

-10dB

-20dB

-20dB

-40dBFS -30dB -30dB

-40dB

-40dB

38 AVR-1909/789, AVC-1909

SEMICONDUCTORSOnly major semiconductors are shown, general semiconductors etc. are omitted to list.

1. ICsM30879FLBFP (IC802)P1_0/D8 P1_1/D9 P1_2/D10 P1_3/D11 P1_4/D12 P1_5/D13/INT3 P1_6/D14/INT4 P1_7/D15/INT5 P2_0/AN2_0/A0(/D0/-) P2_1/AN2_1/A1(/D1/D0) P2_2/AN2_2/A2(/D2/D1) P2_3/AN2_3/A3(/D3/D2) P2_4/AN2_4/A4(/D4/D3) P2_5/AN2_5/A5(/D5/D4) P2_6/AN2_6/A6(/D6/D5) P2_7/AN2_7/A7(/D7/D6) VSS P3_0/A8(/-/D7) VCC2 P3_1/A9 P3_2/A10 P3_3/A11 P3_4/A12 P3_5/A13 P3_6/A14 P3_7/A15 P4_0/A16 P4_1/A17 P4_2/A18 P4_3/A1980 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51

P0_7/AN0_7/D7 P0_6/AN0_6/D6 P0_5/AN0_5/D5 P0_4/AN0_4/D4 P0_3/AN0_3/D3 P0_2/AN0_2/D2 P0_1/AN0_1/D1 P0_0/AN0_0/D0 P10_7/AN7/KI3 P10_6/AN6/KI2 P10_5/AN5/KI1 P10_4/AN4/KI0 P10_3/AN3 P10_2/AN2 P10_1/AN1 AVSS P10_0/AN0 VREF AVCC P9_7/ADTRG/SIN4

81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

M30626FHPFP

50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31

P4_4/CS0 P4_5/CS1 P4_6/CS2 P4_7/CS3 P5_0/WRL/WR P5_1/WRH/BHE P5_2/RD P5_3/BCLK P5_4/HLDA P5_5/HOLD P5_6/ALE P5_7/RDY/CLKOUT P6_0/CTS0/RTS0 P6_1/CLK0 P6_2/RXD0/SCL0 P6_3/TXD0/SDA0 P6_4/CTS1/RTS1/CTS0/CLKS1 P6_5/CLK1 P6_6/RXD1/SCL1 P6_7/TXD1/SDA1

NOTES: 1. P7_0 and P7_1 are N channel open-drain output pins.

M30879FLBFP Terminal FunctionPin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Pin Name P96/TXD4 P95/CLK4 P94/TB4 P93/TB3 P92/ SOUT3 P91/SIN3 P90/CLK3 BYTE CNVCS P87 P86 RESET XOUT VSS XIN Symbol SIRIUS TXD MICDET H/PDET FL_DATA MOSI SOMIm CLKMO BYTE CNVSS FL_RST GRNLED RESET XOUT VSS XIN I/O O I I O O I O I I O O I O I Type C C C C C C Lv Lv Det Lv Lv Op (Int.) Op (Ext.) Eu Eu Ed Ed Ed Eu Res Z Z Z Z Z Z Z Z Z Z L Stby O/L O/L O/L O/L O/L I O/L I O/L O/L I O/L I Stop O/L O/L O/L O/L O/L O/L O/L I O/L O/L I O/L I SIRIUS control pin Microphone detect input (Detected : H) HEADPHONE detect input (Detected : H) FLD DRIVER control pin MAIN-SUB com comm. control pin MAIN-SUB com comm. control pin MAIN-SUB com comm. control pin MAIN-SUB com comm. control pin UP GRADE PIN FLD DRIVER Reset control pin STBYLED GREEN control pin u-COM RESET SIGNAL INPUT OSILATOR CONNECTION GND OSILATOR CONNECTION Function

P9_5/ANEX0/CLK4 P9_4/DA1/TB4IN P9_3/DA0/TB3IN P9_2/TB2IN/SOUT3 P9_1/TB1IN/SIN3 P9_0/TB0IN/CLK3 BYTE CNVSS P8_7/XCIN P8_6/XCOUT RESET XOUT VSS XIN VCC1 P8_5/NMI P8_4/INT2/ZP P8_3/INT1 P8_2/INT0 P8_1/TA4IN/U P8_0/TA4OUT/U P7_7/TA3IN P7_6/TA3OUT P7_5/TA2IN/W P7_4/TA2OUT/W P7_3/CTS2/RTS2/TA1IN/V P7_2/CLK2/TA1OUT/V P7_1/RXD2/SCL2/TA0IN/TB5IN(1) P7_0/TXD2/SDA2/TA0OUT(1)

P9_6/ANEX1/SOUT4

39 AVR-1909/789, AVC-1909

Pin 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76

Pin Name VCC P85/NMI P84/INT2 P83/INT1 P82/INT0 P81 P80 P77 P76 P75 P74 P73/CTS2 P72/CLK2 P71/RXD2 P70/TXD2 P67/TXD1 P66/RXD1 P65/CLK1 P64/CTS1 P63/TXD0 P62/RXD0 P61/CLK0 P60/CTS0 P57 P56 P55/EPM P54 P53 P52 P51 P50/CE P47 P46 P45 P44 P43 P42 P41 P40 P37 P36 P35 P34 P33 P32 P31 VCC P30 VSS P27 P26 P25 P24 P23 P22 P21 P20 P17/INT5 P16/INT4 P15/INT3 P14/D12 VCC NMI

Symbol

I/O I I I I I I I O O I O O I O O I O O O I I I O O O O O O O O I O O O O I O O I O I I I O O I O O O O O O O O I I I O

Type C C C C N C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

Det E &L Lv Lv Lv Lv Lv Lv E &H E &H E &L E &L -

Op (Int.) -

Op (Ext.) Eu Eu Ed Eu Eu Eu Eu Ed Eu Ed Ed Eu Eu Ed Eu Ed Ed Eu Eu Eu Ed Eu Ed Ed Ed Ed Eu -

Res Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z

Stby I I O/L O/L O/L O/L O/L O/L O/L O/L O/L I O/L O/L I O/L O/L O/L I O/L O/L O/H O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L I I I O/L

Stop I I O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L I O/L I O/L POWER 5V 5V

Function

PROTECTION POWERKEY REMOTEDET ISELB VSELA SSELA HD AUDIO LED SSELB VOLDATA VOLCLK RXDMIXO TXDMOXMI MO232CI MI232CO EXPCLK EXPDATA MOIPI MIIPO VSELB ISELA REDLED FL_CE1 FRASH CE/FL_CLK M232CPOWER DYN GRN LED DYN RED LED TRIGGER1 FRASH CE RDSDOUT TURDSCLK(CKTU) TURDSDATA(DATATU) RDSCE RDSRST THERMAL EXPOE EXPSTB TUDOUT(DATAOUT) TUSTB STEREO TUNED IPDET REMOTEPOWER 232C CONTROL VCC VOLPROTECT VSS PRE POWER SCPUPOWER XMPOWER POWER CPU/EPOWER LIMIT REMOCOM REQSOMIm B.DOWN RST SUB

PROTECTION SIGNAL INPUT MAIN POWER relay control output ROOM TO ROOM Signal detect pin (Detected : H) Input selector rotation detect input (Rotary encoder) Master Volume rotation detect input (Rotary encoder) Selector rotation detect input (Rotary encoder) Not used HD AUDIO LED control Selector rotation detect input (Rotary encoder) Volume control pin Volume control pin XM RADIO control pin XM RADIO control pin RS232C SIGNAL OUTPUT RS232C SIGNAL INPUT Extended IC control pin Extended IC control pin iPod control pin iPod control pin Master Volume rotation detect input (Rotary encoder) Input selector rotation detect input (Rotary encoder) STBY LED RED CONTROL FLD DRIVER control pin Rewrite boot program start : L input set /FLD DRIVER control pin RS232C POWER control pin (STANDBY:H) DYNAMIC VOLUME LED GREEN control DYNAMIC VOLUME LED RED control TRIGGER OUT 1 control pin Rewrite boot program start : H input set RDS DETECT IN control pin TUNER/RDS CLOCK OUT TUNER/RDS DATA OUT control pin RDS Chip enable RDS reset output Temperature detect Extended IC control pin Extended IC control pin TUNING DATA INPUT control pin TUNER STB OUT When TUNER FM stereo receive : L TUNER turned detect (Detected : L) MINI JACK connected detection pin for DOCK connection (H:DETECTIVE) REMOTE POWER control pin (ON : H) 232C control pin (MAIN : L / SUB : H) +5V Voltage detection control pin GND PRE POWER control pin (H : ON) SUB CPU POWER ON/OFF switcing (H : ON) XM RADIO POWER control pin MAIN POWER relay control output (ON : H) MAIN CPU POWER control pin (POWER ON : H) LIMIT control Not used Not used Remote control signal input MAIN-SUB com comm. control pin Power down detect (Power down : L) SUB com Reset control pin

40 AVR-1909/789, AVC-1909

Pin 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

Pin Name P13/D11 P12/D10 P11/D9 P10/D8 P07/D7 P06/D6 P05/D5 P04/D4 P03/D3 P02/D2 P01/D1 P00/D0 P103/AN3 P102/AN2 P101/AN1 P104/AN4 P107/AN7 P106/AN6 P105/AN5 AVSS P100/AN0 VREF AVCC P97/RXD4

Symbol LIMITDET VOLMUTE MUTEPOWER SYNCDET OSDMUTE OSDRST OSDSTR OSDCLK OSDDATA KEY1 KEY2 KEY3 ACKSUB XMOLINKACTIVE XMOANTREV XMIRESET AVSS SET_OPTION VREF AVCC SIRIUS RXD

I/O I O O O O I O O O O O O I I I O I I O I I

Type C C C C C C C C C C C C -

Det Lv Lv Lv Lv Lv E &L Lv -

Op (Int.) -

Op (Ext.) Eu Ed Ed Eu Eu Eu Ed Ed Ed Eu Ed

Res Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z

Stby O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L

Stop O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L O/L

Function Signal detect input (Detected : H) Not used Not used VOLUME MUTE control pin For MUTE +B control pin Sync. detect input for MAIN(H: Ext. synchronized) OSD control pin Not used OSD control pin OSD control pin OSD control pin OSD control pin KEY1 SIGNAL INPUT KEY2 SIGNAL INPUT KEY3 SIGNAL INPUT MAIN-SUB com comm. control pin XM RADIO control pin XM RADIO control pin XM RADIO RESET control pin GND SET OPTION SELECT VREF POWER 5V SIRIUS control pin

Note:

Pin No. Port Name Symbol I/O Type

Op

Det Res

STBY Stop

Terminal number of microcomputer. The name entered in the data sheet of microcomputer. Symbolized interface function. Input or out of part. I = Input port O = Output port : Composition of port in case of output port. C = CMOS output N = NMOS open drain output P = PMOS open drain output : Pull up/Pull down selection information. Iu = Inner microcomputer pull up Id = Inner microcomputer pull down Eu = External microcomputer pull up Ed = External microcomputer pull down : Indicates judging state of input port. Level detection is LV; Edge detection is Ed; Detection by both shifting is E&L; Serial data detection is S (Serial data output is also S). : State at reset. H = Outputs High Level at reset L = Outputs Low Level at reset Z = Becomes High impedance mode at reset : State of port when STANDBY mode. O/L = Output port and L I = Input port : State of port when Stop mode. O/L = Output port and L I = Input port

: : : :

41 AVR-1909/789, AVC-1909

M3062LFGPGP (IC1405)

M3062LFGPGP Terminal FunctionPin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Pin Name P94/TB4 P93/TB3 P92/SOUT3 P91/SIN3 P90/CLK3 BYTE CNVCS P87 P86 RESET XOUT VSS XIN VCC P85/NMI P84/INT2 P83/INT1 P82/INT0 P81 P80 P77 P76 P75 Symbol VPLD DATA DIR CE DIR DIN DIR DOUT DIR CLK BYTE CNVSS VERST VDRST SUBRESET X1 VSS X2 VCC NMI CEC_IN ACKSIMO SUB BDOWN IP RST SICODECO CPU_MUTE/TMS APLDSEL1/TDI I/O O O O I O O O I O I I I I I O I I O O Type C C C C C C C C C Det Lv Lv E &L E &L E &L Op (Int.) Op (Ext.) Eu Eu Eu Eu Eu Ed Eu Ed Res Z Z Z Z Z Z Z L Z Z Z Z Z Z Z Z VIDEO PLD control pin DIR control pin(LC89057W-VF4A) DIR control pin(LC89057W-VF4A) DIR control pin(LC89057W-VF4A) DIR control pin(LC89057W-VF4A) GND(Ext. data bus bit width switching, 16bit:L) Single-chip/Micro-processor mode switching(Normal single-chip:L, Rewrite boot program start:H input set) Reset for VIDEO ENCODER(ADV7172) Reset for VIDEO DECODER(ADV7401) Reset input Oscillator connection GND Oscillator connection +3.3V Not used(Fixed to H) CEC-D signal input pin MAIN-SUB com comm. control input pin("L" return from MAIN com) Power down detect(Power down:L) IP CONV(FLI2310) reset Not used CODEC (ADAU1328) control pin MAIN PLD DAC MUTE control pin/PLD rewrite control(JTAG) MAIN PLD control pin/PLD rewrite control(JTAG) Function

42 AVR-1909/789, AVC-1909

Pin 24 25 26 27

Pin Name P74 P73/CTS2 P72/CLK2 P71/RXD2 MTCK

Symbol

I/O O O O I/O

Type C C C N

Det -

Op (Int.) -

Op (Ext.) Ed Eu

Res Z Z Z Z PLD rewrite control(JTAG)

Function

VIDEO_POWER DAC_POWER VSCL

VIDEO Power ON/OFF switching(H:ON) DIGITAL Power ON/OFF switching(H:ON) VIDEO I2C- IP CONV(FLI2310)/V_ENCODER(ADV7172)/ V_DECODER(ADV7401)/COMPONENT SELECT IC(NJW1321FP1) control IC VIDEO I2C- IP CONV(FLI2310)/V_ENCODER(ADV7172)/ V_DECODER(ADV7401)/COMPONENT SELECT IC(NJW1321FP1) control IC Data transmission output to outside Data transmission input from outside Additional instructions to Front of an SW signal(H:ON) HDMI POWER control pin(H:ON) MAIN-SUB com comm. control pin MAIN-SUB com comm. control pin MAIN-SUB com comm. control pin MAIN-SUB com comm. control pin SiI9185 Reset pin HD DET control pin Rewrite boot program start : L input set CEC-D signal output pin COMPONENT MONITOR OUT output control pin Not used VCR1OUT output INH control (L:MUTE) Write Protect control / Rerite boot program start : H input set HDMI IN SEL(SiI9185) INT output H:DSP Power ON HP DET control pin COMPONENT CONVERT output control pin HDMI RECEIVER(SiI9031)INT output VIDEO I2C/HDMI EDIT(E2PROM) control pin VIDEO I2C/HDMI EDIT(E2PROM) control pin Z1 SMONITOR select Reset for HDMI RECEIVER(SiI9135) Reset for HDMI TRANSMITTER1 Z1 SMONITOR select HDMI OUT signal detect input(HDMI TRANS1 SiI9134) Not used CODEC (ADAU1328) control pin CODEC (ADAU1328) control pin +3.3V CODEC (ADAU1328) control pin GND CODEC (ADAU1328) control pin XMDAC control pin (AK4385) XMDAC control pin (AK4385) XMDAC control pin (AK4385) XMDAC control pin (AK4385) Terminal output for VIDEO expander control(BU4094BCFV) Terminal output for VIDEO expander control(BU4094BCFV) CLK output for VIDEO expander control(BU4094BCFV) DATA output for VIDEO expander control(BU4094BCFV) COMPONENT IN signal detect input VIDEO IN signal detect input (Signal inputted : H) S MONITER connection existence detection input (connected:L) S signal detect input (signal inputted:H) SyncDet pin A.PLD Control Bit Digital Power ON/OFF control pin PLD JTAGLINE ON/OFF control VIDEO PLD control pin/PLD rewrite control (JTAG) HP DET control pin HP DET control pin DIR1 control pin Not used Not used DIR1 control pin

28

P70/TXD2

VSDA

I/O

N

-

-

Eu

Z

29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

P67/TXD1 P66/RXD1 P65/CLK1 P64/CTS1 P63/TXD0 P62/RXD0 P61/CLK0 P60/CTS0 P57 P56 P55/EPM P54 P53 P52 P51 P50/CE P47 P46 P45 P44 P43 P42 P41 P40 P37 P36 P35 P34 P33 P32 P31 VCC P30 VSS P27 P26 P25 P24 P23 P22 P21 P20 P17/INT5 P16/INT4 P15/INT3 P14/D12 P13/D11 P12/D10 P11/D9 P10/D8 P07/D7 P06/D6 P05/D5 P04/D4 P03/D3 P02/D2 P01/D1 P00/D0

TXD RXD SW SUM HDMIPOWER SOMI SIMO CLKSIMO REQSOMI 1TMDSSWRST HDP2 ADPDOWN/AUTH CEC_OUT MONIDIS VCR2INH (CDR) VCR1INH (VCR) WP4/(AVMUTE) HS_INT DSPPWR HDP1 P.SAVE HRINT HSCL/EDID SCL HSDA/EDID SDA Z1SMONIA HDMIR_RST 1HTRST Z1SMONIB 1HTINT PAL/NTSC SOCODECI CLKCODEC VCC CECODEC VSS CODECRST XMDACRST XMDACCS XMDACMC XMDACMDI VEXPSTB VEXPOE VEXPCLK VEXPDIN COMPSDET Z1VSIG.DET Z1SMONIDET Z1SSIGDET SYNCDET CPUCONT D.POWER PLDWRITE VPLDCE/TDO HDP3 HDP4 INT1 INT2 DIRRST2 DIRRST1

O I O O O I I O O O I O O O O O/I I O O O I I/O I/O O O O O I O O O O O O O O O O O O O I I I I I O O O O/I O O I O O O

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

Lv E &L E &L Lv Lv Lv Lv Lv -

-

Eu Eu Ed Ed Ed Ed Ed Eu Eu Ed Ed Ed Eu Eu Eu Eu Ed . Ed Ed Eu Eu Eu Eu Ed Ed Eu -

Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z

43 AVR-1909/789, AVC-1909

Pin 87 88 89 90 91 92 93 94 95 96 97 98 99 100

Pin Name P107/AN7 P106/AN6 P105/AN5 P104/AN4 P103/AN3 P102/AN2 P101/AN1 AVSS P100/AN0 VREF AVCC P97/SIN4 P96/SOUT4 P95/CLK4

Symbol DSPRST DSPROMRST DSPFLAG0 DSPICS DSP FLAG1 AVSS VPLDCLK VREF AVCC DSPMISO DSPMOSI DSPICLK

I/O O O O O I O I O I O O

Type C C C C C C C

Det Lv Lv -

Op (Int.) -

Op (Ext.) Ed Ed Eu Eu Eu Eu

Res Z Z Z Z Z Z Z Z Z Z Z

Function DSP (ADSP-21367) reset output pin (reset:L) Not used DSP memory reset(reset:L) Not used DSP control pin (ADSP-21367) DSP control pin (ADSP-21367) Not used AD GND VIDEO PLD control pin AD ref. +3.3V AD +3.3V DSP control pin (ADSP-21367) DSP control pin (ADSP-21367) DSP control pin (ADSP-21367)

Note:

Pin No. Port Name Symbol I/O Type

Op

Det Res

STBY Stop

Terminal number of microcomputer. The name entered in the data sheet of microcomputer. Symbolized interface function. Input or out of part. I = Input port O = Output port : Composition of port in case of output port. C = CMOS output N = NMOS open drain output P = PMOS open drain output : Pull up/Pull down selection information. Iu = Inner microcomputer pull up Id = Inner microcomputer pull down Eu = External microcomputer pull up Ed = External microcomputer pull down : Indicates judging state of input port. Level detection is LV; Edge detection is Ed; Detection by both shifting is E&L; Serial data detection is S (Serial data output is also S). : State at reset. H = Outputs High Level at reset L = Outputs Low Level at reset Z = Becomes High impedance mode at reset : State of port when STANDBY mode. O/L = Output port and L I = Input port : State of port when Stop mode. O/L = Output port and L I = Input port

: : : :

44 AVR-1909/789, AVC-1909

FLI2310 (IC1011)FIELD ID_PORT2 D1_IN_7 D1_IN_6 D1_IN_5 IN_CLK_PORT2 HSYNC_PORT2 AVDD_PLL_BE2 AVDD_PLL_BE1 AVSS_PLL_BE1 VSYNC_PORT2 AVSS_PLL_SDI AVSS_PLL_BE2 R_VSS AVSS_PLL_FE AVDD_PLL_FE AVDD_PLL_SDI PLL_PVSS PLL_PVDD VDD9 XTAL OUT

Reserved Reserved Reserved

Reserved

R_VDD Reserved

R_VDD

170

R_VDD1.8

VDDcore8 D1_IN_0

VSScore

R_VDD

Reserved R_VSS

D1_IN_4 D1_IN_3 D1_IN_2 D1_IN_1

XTAL IN TEST2

R_VSS R_VSS

R_VSS R_VDD

R_VDD

R_VSS

R_VSS

R_VDD

TEST1

TEST0

R_VSS

VSS

205

200

195

190

185

175

HSYNC1_PORT1 VSYNC1_PORT1 FIELD ID1_PORT1 IN_CLK1_PORT1 HSYNC2_PORT1 VSYNC2_PORT1 FIELD ID2_PORT1 VDD1 VSS IN_CLK2_PORT1 B/Cb/D1_0 B/Cb/D1_1 B/Cb/D1_2 B/Cb/D1_3 B/Cb/D1_4 VDDcore1 VSScore B/Cb/D1_5 B/Cb/D1_6 B/Cb/D1_7 R/Cr/Cb Cr_0 R/Cr/Cb Cr_1 R/Cr/Cb Cr_2 R/Cr/Cb Cr_3 R/Cr/Cb Cr_4 R/Cr/Cb Cr_5 R/Cr/Cb Cr_6 R/Cr/Cb Cr_7 G/Y/Y_0 VDD2 VSS G/Y/Y_1 G/Y/Y_2 G/Y/Y_3 G/Y/Y_4 VDDcore2 VSScore G/Y/Y_5 G/Y/Y_6 G/Y/Y_7 IN_SEL TEST DEV_ADDR1 DEV_ADDR0 SCLK SDATA RESET_N VDD3 VSS SDRAM DATA(0) SDRAM DATA(1) SDRAM DATA(2)

1 155

180

165

160

OE G/Y/Y_OUT_7 G/Y/Y_OUT_6 G/Y/Y_OUT_5 G/Y/Y_OUT_4

5 150

G/Y/Y_OUT_3 G/Y/Y_OUT_2 G/Y/Y_OUT_1 G/Y/Y_OUT_0

10 145

VSS VDD8 R/V/Pr_OUT_7 R/V/Pr_OUT_6 R/V/Pr_OUT_5

15 140

R/V/Pr_OUT_4 R/V/Pr_OUT_3 R/V/Pr_OUT_2 VSScore VDDcore7 R/V/Pr_OUT_1 R/V/Pr_OUT_0

20 135

B/U/Pb_OUT_7 B/U/Pb_OUT_6 B/U/Pb_OUT_5 B/U/Pb_OUT_4

25 130

B/U/Pb_OUT_3 B/U/Pb_OUT_2 VSS VDD7 B/U/Pb_OUT_1

30 125

B/U/Pb_OUT_0 CLKOUT VSScore VDDcore6 CTLOUT4

35 120

CTLOUT3 CTLOUT2 CTLOUT1 CTLOUT0 TEST OUT1 TEST OUT0

40 115

TEST3 SDRAM CLKIN VSS VDD6

45 110

SDRAM CLKOUT SDRAM DQM SDRAM CSN SDRAM BA0 SDRAM BA1

50 100 85 90 70 80 95 105

SDRAM CASN SDRAM RASN

65

55

SDRAM DATA(3)

SDRAM DATA(4)

SDRAM DATA(5)

60

75SDRAM DATA(23) SDRAM DATA(24)

SDRAM DATA(31)

SDRAM DATA(6) SDRAM DATA(7)

SDRAM DATA(8)

SDRAM DATA(20) SDRAM DATA(21)

SDRAM DATA(9) SDRAM DATA(10)

SDRAM DATA(25)

VSScore SDRAM DATA(26)

SDRAM DATA(27)

SDRAM DATA(12)

SDRAM DATA(13)

SDRAM DATA(14)

SDRAM DATA(15) VDDcore3 VSScore SDRAM DATA(16)

SDRAM DATA(17)

SDRAM DATA(18) SDRAM DATA(19)

SDRAM DATA(28)

SDRAM ADDR(9)

SDRAM ADDR(8) SDRAM ADDR(7)

SDRAM ADDR(6)

SDRAM ADDR(5) SDRAM ADDR(4)

SDRAM ADDR(3)

SDRAM ADDR(2)

SDRAM ADDR(1)

SDRAM DATA(22)

SDRAM DATA(29)

SDRAM DATA(11)

SDRAM DATA(30)

TEST IN SDRAM ADDR(10)

SDRAM ADDR(0)

VDDcore4

VDDcore5 VSScore

VDD4

VSS

VDD5 VSS

FLI2310 Block DiagramPort 2 8-bit 656 Input Port 1 8/16/24-bit RGB/YCrCb Input Input Processor with Auto Sync and auto Adjust Noise Reducer, Deinterlacer, Frame Rate Converter and SDRAM interface Vertical and Horizontal Scalers Output Processor 16/20/24-bit RBG/YCrCb Digital Outputs Vertical and Horizontal Enhancers

Clock Generation PLLs

2Mx32 SDRAM (external)

45 AVR-1909/789, AVC-1909

SDRAM WEN

FLI2310 Terminal FunctionPin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 ab e 3 3 0 p de a s Voltage Pull up/ I/O Type Tolerance Drive Pulldown Description Horizontal sync or reference -CTL1 of Port 1 Input 5v Vertical sync or reference -CTL1 of Port 1 Input 5v Odd/Even Field identification -CTL1 of Port 1 Input 5v Data Clock input -CTL1 of Port 1 Input 5v Horizontal sync or reference CTL2 of Port 1 Input 5v Vertical sync or reference CTL2 of Port 1 Input 5v Odd/Even Field identification CTL2 of Port 1 Input 5v Power 3.3 V - Power pin for IO Ground Ground Data Clock input CTL2 of Port 1 Input 5v Port 1 Digital video input (Blue/Cb/D1) Input 5v Port 1 Digital video input (Blue/Cb/D1) Input 5v Port 1 Digital video input (Blue/Cb/D1) Input 5v Port 1 Digital video input (Blue/Cb/D1) Input 5v Port 1 Digital video input (Blue/Cb/D1) Input 5v Power 1.8 V - Power pin for core Ground Ground Port 1 Digital video input (Blue/Cb/D1) Input 5v Port 1 Digital video input (Blue/Cb/D1) Input 5v Port 1 Digital video input (Blue/Cb/D1) Input 5v Port 1 Digital video input (Red/Cr/CrCb) Input 5v Port 1 Digital video input (Red/Cr/CrCb) Input 5v Port 1 Digital video input (Red/Cr/CrCb) Input 5v Port 1 Digital video input (Red/Cr/CrCb) Input 5v Port 1 Digital video input (Red/Cr/CrCb) Input 5v Port 1 Digital video input (Red/Cr/CrCb) Input 5v Port 1 Digital video input (Red/Cr/CrCb) Input 5v Port 1 Digital video input (Red/Cr/CrCb) Input 5v Port 1 Digital video input (Green/Y) Input 5v Power 3.3 V - Power pin for IO Ground Ground Port 1 Digital video input (Green/Y) Input 5v Port 1 Digital video input (Green/Y) Input 5v Port 1 Digital video input (Green/Y) Input 5v Port 1 Digital video input (Green/Y) Input 5v Power 1.8 V - Power pin for core Ground Ground Port 1 Digital video input (Green/Y) Input 5v Port 1 Digital video input (Green/Y) Input 5v Port 1 Digital video input (Green/Y) Input 5v Output to select external video mux Output 5v 8 mA Connect to Ground Input 5v Device address setting 1 Input 5v Device address setting 0 Input 5v

Pin Name HSYNC1_PORT1 VSYNC1_PORT1 FIELD ID1_PORT1 IN_CLK1_PORT1 HSYNC2_PORT1 VSYNC2_PORT1 FIELD ID2_PORT1 VDD1 VSS IN_CLK2_PORT1 B/Cb/D1_0 B/Cb/D1_1 B/Cb/D1_2 B/Cb/D1_3 B/Cb/D1_4 VDDcore1 VSScore B/Cb/D1_5 B/Cb/D1_6 B/Cb/D1_7 R/Cr/Cb Cr_0 R/Cr/Cb Cr_1 R/Cr/Cb Cr_2 R/Cr/Cb Cr_3 R/Cr/Cb Cr_4 R/Cr/Cb Cr_5 R/Cr/Cb Cr_6 R/Cr/Cb Cr_7 G/Y/Y_0 VDD2 VSS G/Y/Y_1 G/Y/Y_2 G/Y/Y_3 G/Y/Y_4 VDDcore2 VSScore G/Y/Y_5 G/Y/Y_6 G/Y/Y_7 IN_SEL TEST DEV_ADDR1 DEV_ADDR0

46 AVR-1909/789, AVC-1909

Pin No 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

Pin Name SCLK SDATA RESET_N VDD3 VSScore SDRAM DATA(0) SDRAM DATA(1) SDRAM DATA(2) SDRAM DATA(3) SDRAM DATA(4) SDRAM DATA(5) SDRAM DATA(6) SDRAM DATA(7) SDRAM DATA(8) SDRAM DATA(9) SDRAM DATA(10) SDRAM DATA(11) VDD4 VSS SDRAM DATA(12) SDRAM DATA(13) SDRAM DATA(14) SDRAM DATA(15) VDDcore3 VSScore SDRAM DATA(16) SDRAM DATA(17) SDRAM DATA(18) SDRAM DATA(19) SDRAM DATA(20) SDRAM DATA(21) SDRAM DATA(22) SDRAM DATA(23) SDRAM DATA(24) SDRAM DATA(25) VDDcore4 VSScore SDRAM DATA(26) SDRAM DATA(27) SDRAM DATA(28) SDRAM DATA(29) SDRAM DATA(30) SDRAM DATA(31) VDD5

Voltage Pull up/ I/O Type Tolerance Drive Pulldown Description 5v 8 mA 2-wire serial control bus clock I/O 5v 8 mA 2-wire serial control bus data I/O 5v PU Reset Input 3.3 V Power pin for IO Power Ground Ground SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O 3.3 V Power pin for IO Power Ground Ground SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O 1.8 V - Power pin for core Power Ground Ground SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O 1.8 V Power pin for core Power Ground Ground 5v 4 mA PD SDRAM data bus * Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O SDRAM data bus * 5v 4 mA PD Tristate I/O 3.3 V Power pin for IO Power

47 AVR-1909/789, AVC-1909

Pin No 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116

Pin Name VSS TEST IN SDRAM ADDR(10) SDRAM ADDR(9) SDRAM ADDR(8) SDRAM ADDR(7) SDRAM ADDR(6) VDDcore5 VSScore SDRAM ADDR(5) SDRAM ADDR(4) SDRAM ADDR(3) SDRAM ADDR(2) SDRAM ADDR(1) SDRAM ADDR(0) SDRAM WEN SDRAM RASN SDRAM CASN SDRAM BA1 SDRAM BA0 SDRAM CSN SDRAM DQM SDRAM CLKOUT VDD6 VSS SDRAM CLKIN TEST3 TEST OUT0 TEST OUT1 / Interrupt 117 Out 118 CTLOUT0 119 CTLOUT1 120 CTLOUT2 121 CTLOUT3 122 CTLOUT4 123 124 125 126 127 VDDcore6 VSScore CLKOUT B/U/Pb_OUT_0 B/U/Pb_OUT_1

Voltage Pull up/ I/O Type Tolerance Drive Pulldown Description Ground Ground 5V Test input-Connect to ground Input 5v 8 mA SDRAM address bus * Tristate O/P 5v 8 mA SDRAM address bus * Tristate O/P 5v 8 mA SDRAM address bus * Tristate O/P 5v 8 mA SDRAM address bus * Tristate O/P 5v 8 mA SDRAM address bus * Tristate O/P 1.8 V Power pin for core Power Ground Ground 5v 8 mA SDRAM address bus * Tristate O/P 5v 8 mA SDRAM address bus * Tristate O/P 5v 8 mA SDRAM address bus * Tristate O/P 5v 8 mA SDRAM address bus * Tristate O/P 5v 8 mA SDRAM address bus * Tristate O/P 5v 8 mA SDRAM address bus * Tristate O/P 5v 8 mA SDRAM write enable * Tristate O/P 5v 8 mA SDRAM row address select * Tristate O/P 5v 8 mA SDRAM column address select * Tristate O/P 5v 8 mA SDRAM bank select 1* Tristate O/P 5v 8 mA SDRAM bank select 0* Tristate O/P 5v 4 mA SDRAM CS * Tristate O/P 5v 8 mA SDRAM DQM * Tristate O/P 5v 12 mA Clock out to SDRAM * Output 3.3 V - Power pin for IO Power Ground Ground 5v Trace delayed SDRAM Clock in Input Test input Connect to ground Input Test output leave open Output Output Tristate O/P Tristate O/P Tristate O/P Tristate O/P Tristate O/P Power Ground Tristate O/P Tristate O/P Tristate O/P 5v 5v 5v 5v 5v 8 mA 8 mA 8 mA 8 mA 8 mA Interrupt Output Control signal output selectable as HSync1/ CSync/HRef/Monitor coast Control signal output selectable as VSync1/CRef/VRef/Film Indicator Control signal output selectable as Monitor coast/HRef/VDD_en / HSync2 Control signal output selectable as Film Indicator/VRef/backlight_en/VSync2 Control signal output selectable as CRef/Field ID/CSync/Monitor coast 1.8 V - Power pin for core Ground Output data rate clock Digital video output Blue/U/Pb Digital video output Blue/U/Pb

5v 5v 5v

12 mA 8 mA 8 mA

48 AVR-1909/789, AVC-1909

Pin No 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171

Pin Name VDD7 VSS B/U/Pb_OUT_2 B/U/Pb_OUT_3 B/U/Pb_OUT_4 B/U/Pb_OUT_5 B/U/Pb_OUT_6 B/U/Pb_OUT_7 R/V/Pr_OUT_0 R/V/Pr_OUT_1 VDDcore7 VSScore R/V/Pr_OUT_2 R/V/Pr_OUT_3 R/V/Pr_OUT_4 R/V/Pr_OUT_5 R/V/Pr_OUT_6 R/V/Pr_OUT_7 VDD8 VSS G/Y/Y_OUT_0 G/Y/Y_OUT_1 G/Y/Y_OUT_2 G/Y/Y_OUT_3 G/Y/Y_OUT_4 G/Y/Y_OUT_5 G/Y/Y_OUT_6 G/Y/Y_OUT_7 OE PLL_PVDD PLL_PVSS AVSS_PLL_BE1 AVDD_PLL_BE1 AVDD_PLL_BE2 AVSS_PLL_BE2 AVSS_PLL_SDI AVDD_PLL_SDI AVDD_PLL_FE AVSS_PLL_FE DAC_PVSS DAC_VDD DAC_VSS DAC_BOUT DAC_AVDDB

Voltage Pull up/ I/O Type Tolerance Drive Pulldown Description 3.3 V Power pin for IO Power Ground Ground 5v 8 mA Digital video output Blue/U/Pb Tristate O/P Digital video output Blue/U/Pb 5v 8 mA Tristate O/P Digital video output Blue/U/Pb 5v 8 mA Tristate O/P Digital video output Blue/U/Pb 5v 8 mA Tristate O/P Digital video output Blue/U/Pb 5v 8 mA Tristate O/P Digital video output Blue/U/Pb 5v 8 mA Tristate O/P 5v 8 mA Digital video output Red/V/Pr Tristate O/P 5v 8 mA Digital video output Red/V/Pr Tristate O/P 1.8 V Power pin for core Power Ground Ground Digital video output Red/V/Pr 5v 8 mA Tristate O/P Digital video output Red/V/Pr 5v 8 mA Tristate O/P Digital video output Red/V/Pr 5v 8 mA Tristate O/P Digital video output Red/V/Pr 5v 8 mA Tristate O/P Digital video output Red/V/Pr 5v 8 mA Tristate O/P Digital video output Red/V/Pr 5v 8 mA Tristate O/P 3.3 V Power pin for IO Power Ground Ground 5v 8 mA Digital video output Green/Y Tristate O/P Digital video output Green/Y 5v 8 mA Tristate O/P Digital video output Green/Y 5v 8 mA Tristate O/P Digital video output Green/Y 5v 8 mA Tristate O/P Digital video output Green/Y 5v 8 mA Tristate O/P Digital video output Green/Y 5v 8 mA Tristate O/P Digital video output Green/Y 5v 8 mA Tristate O/P Digital video output Green/Y 5v 8 mA Tristate O/P 5v Output data enable for Digital video output Input 1.8 V Power pin for PLL pads Power Ground for PLL pads Ground PLL Ground Ground 1.8 V Power pin for PLL Power 1.8 V Power pin for PLL Power PLL Ground Ground PLL Ground Ground 1.8 V Power pin for PLL Power 1.8 V Power pin for PLL Power PLL Ground Ground Ground for DAC pads Ground Power 1.8 V Digital power pin for DAC Ground DAC digital Ground 34 mA Analog B/U output Output 3.3 V Analog power pin for B channel Power

49 AVR-1909/789, AVC-1909

Pin No 172 173 174 175 176 177 178 179 180

Pin Name DAC_AVSSB DAC_GOUT DAC_AVDDG DAC_AVSSG DAC_ROUT DAC_AVDDR DAC_AVSSR DAC_COMP DAC_RSET

181 DAC_VREFOUT 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 Note: DAC_VREFIN DAC_AVDD DAC_AVSS DAC_GR_AVSS DAC_GR_AVDD DAC_PVDD TEST0 TEST1 TEST2 XTAL IN XTAL OUT VDD9 VSS IN_CLK_PORT 2 D1_IN_0 VDDcore8 VSScore D1_IN_1 D1_IN_2 D1_IN_3 D1_IN_4 D1_IN_5 D1_IN_6 D1_IN_7 FIELD ID_PORT 2 VSYNC_ PORT 2 HSYNC_PORT 2

I/O Type Ground Output Power Ground Output Power Ground Output Output Output Input Power Ground Ground Power Power Input Input Input Input Output Power Ground Input Input Power Ground Input Input Input Input Input Input Input Input Input Input

Voltage Pull up/ Tolerance Drive Pulldown Description Analog Ground for B channel 34 mA Analog G/Y output 3.3 V Analog power pin for G channel Analog Ground for G channel 34 mA Analog R/V output 3.3 V Analog power pin for R channel Analog Ground for R channel Compensation for video DACs Current setting resistor for video DACs 1.28 V Internally generated voltage reference for video DACs External Voltage reference for video DACs 3.3 V Analog power pin for DAC Analog Ground for DAC Ground for DAC Guard ring 3.3 V Power pin for DAC Guard ring 3.3 V Power pin for DAC pads 5v Test pin connect to ground 5v Test pin connect to ground 5v Test pin connect to ground External parallel crystal oscillator External parallel crystal oscillator 3.3 V - Power pin for IO Ground 5v 4 mA Port 2 - Data Clock input 5v 4 mA Port 2 - ITU-R BT656 digital data input 1.8 V Power pin for core Ground 5v 4 mA Port 2 - ITU-R BT656 digital data input 5v 4 mA Port 2 - ITU-R BT656 digital data input 5v 4 mA Port 2 - ITU-R BT656 digital data input 5v 4 mA Port 2 - ITU-R BT656 digital data input 5v 4 mA Port 2 - ITU-R BT656 digital data input 5v 4 mA Port 2 - ITU-R BT656 digital data input 5v 4 mA Port 2 - ITU-R BT656 digital data input 5v 4 mA Port 2 - Odd/Even Field identification 5v 4 mA Port 2 - Vertical sync or reference 5v 4 mA Port 2 - Horizontal sync or reference

1) * - The connection of these pins depends on the type of external SDRAM used. See Appendix 3 2) For 16/20 bit Y and muxed C output modes see Appendix 2 for pin configuration

50 AVR-1909/789, AVC-1909

ADSP21367 (IC1024)208 1 PIN 1 INDICATOR 157 156

TOP VIEW (PINS DOWN)

52 53

105 104

ADSP21367 Terminal FunctionPin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Signal VDD DATA28 DATA27 GND IOVDD DATA26 DATA25 DATA24 DATA23 GND VDD DATA22 DATA21 DATA20 IOVDD GND DATA19 DATA18 VDD GND DATA17 VDD GND VDD GND DATA16 DATA15 DATA14 DATA13 DATA12 IOVDD GND VDD GND DATA11 DATA10 DATA9 DATA8 DATA7 DATA6 IOVDD GND VDD DATA4 DATA5 DATA2 DATA3 DATA0 DATA1 IOVDD GND VDD Pin No. 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 Signal VDD GND IOVDD ADDR0 ADDR2 ADDR1 ADDR4 ADDR3 ADDR5 GND VDD GND IOVDD ADDR6 ADDR7 ADDR8 ADDR9 ADDR10 GND VDD GND IOVDD ADDR11 ADDR12 ADDR13 GND VDD AVSS AVDD GND CLKIN XTAL2 IOVDD GND VDD ADDR14 GND IOVDD ADDR15 ADDR16 ADDR17 ADDR18 GND IOVDD ADDR19 ADDR20 ADDR21 ADDR23 ADDR22 MS1 MS0 VDD Pin No. 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 Signal VDD GND IOVDD SDCAS SDRAS SDCKE SDWE WR SDA10 GND IOVDD SDCLK0 GND VDD RD ACK FLAG3 FLAG2 FLAG1 FLAG0 DAI20 GND VDD GND IOVDD DAI19 DAI18 DAI17 DAI16 DAI15 DAI14 DAI13 DAI12 VDD IOVDD GND VDD GND DAI11 DAI10 DAI8 DAI9 DAI6 DAI7 DAI5 IOVDD GND VDD GND VDD GND VDD Pin No. 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 Signal VDD VDD GND VDD VDD VDD TDI TRST TCK GND VDD TMS CLK_CFG0 BOOTCFG0 CLK_CFG1 EMU BOOTCFG1 TDO DAI4 DAI2 DAI3 DAI1 IOVDD GND VDD GND DPI14 DPI13 DPI12 DPI11 DPI10 DPI9 DPI8 DPI7 IOVDD GND VDD GND DPI6 DPI5 DPI4 DPI3 DPI1 DPI2 CLKOUT RESET IOVDD GND DATA30 DATA31 DATA29 VDD

51 AVR-1909/789, AVC-1909

R2A15215FP (IC700)80 81 51 50

100 1 30

31

R2A15215FP Block DiagramBASSR1 SBRIN2 SLIN2 SUBL CIN2 BASSR2 SBRCIN SBLCIN CLOCK SBLIN2 SWIN2 SRIN2 FRIN2 DGND SUBR FLIN2 TRER DATA N.C. N.C. 30 AVCCAVCC

50 49 48 MUTE 51 AVEE 52 N.C. 53 ADCL 54ATT AVEE 0/-6/-12/-18dB

47 46 45 44 43 42 41

40 39 38 37 36 35 34 33

32 31

MCU I/F

29 N.C. 28 TREL 27 BASSL2 26 BASSL1

ADCR 55 AGND 56 N.C. 57 INR1 58 INL1 59 INR2 60 INL2 61 INR3 62SUB SUB MA IN SUB MA IN MA IN

0~-95dB, (0.5dBstep)

Bass/ Tr ble e -14~+14dB (2dB step)

25 N.C.Bypass Tone+MIX Tone

+42~0dB (0.5dBstep)

24 FRC 23 FROUT

Tone Tone0~-95dB, Bass/ Treble -14~+14dB (0.5dBstep) (2dB step)

+42~0dB (0.5dBstep)Tone+MIX Bypass Tone

22 AGND 21 FLOUT 20 FLC 19 AGND

CMIX

INL3 63 INR4 64 INL4 65 INR5 66 INL5 67 INR6 68 INL6 69 INR7 70 INL7 71 INR8 72 INL8 73 N.C. 74 INRA/RECR1 75 INLA/RECL1 76 N.C. 77 INR9 78 INL9 79 N.C. 80 81 82 83 INR10/RECR4 INRB/RECR2 INLB/RECL2REC

+42~-95dB, - (0.5dBstep)

18 CC 17 COUT

SWMIX

16 AGND 15 SWOUT 14 SWC 13 N.C.

+42~-95dB, - (0.5dBstep) +42~-95dB, - (0.5dBstep)

+42~-95dB, - (0.5dBstep)

12 SRC 11 SROUT

+42~-95dB, - (0.5dBstep)

10 AGND 9 SLOUT 8 SLC

+42~-95dB, - (0.5dBstep)

7 AGND 6 SBRC 5 SBR OUT 4 AGND 3 SBL OUT 2 SBLC 1 N.C.

84 85 86 87 88 89 90 N.C. INR11/RECR5 RECR3 N.C. N.C. INL10/RECL4 INL11/RECL5

91 92 93 94 95 96 97 98 RECL3 N.C. CIN1 FRIN1 SWIN1 SRIN1 SLIN1 FLIN1

99 100 SBRIN1 SBLIN1

52 AVR-1909/789, AVC-1909

R2A15215FP Terminl Function

PIN No. 23,21, 17,15, 11,9, 5,3 24,20, 18,14, 12,8, 6,2 4,7,10,16, 19,22,56 28,34 26,27, 32,33 30 43,42, 41,40, 39,38, 37,36 93,94, 95,96, 97,98, 99,100 48 49 50 52 59,61,63, 65,67,69, 71,73,79 58,60,62, 64,66,68, 70,72,78 51 44,45 46,47 54,55 90,91 75,76, 81,82, 83,84, 85,861,13,25,29,31, 35,53, 57,74,77,80, 87,88,89,92

Name FROUT,FLO UT, COUT,SWOUT, SROUT, SLO UT, SBROUT,S BL OUT FRC,FLC, CC,SWC, SRC,SLC, SBRC,SBL C AGN D TREL, TRE R BA SSL1,BA SSL2 BA SSR1,BASSR2 AVCC FRIN2, FLIN2, SRN2,SLIN2, SWIN2,CIN2 , SBRIN2,S BLIN2 FLIN1, F RIN1, CIN1,SWIN1 , SLIN1,S RIN1, SBLIN1,S BRIN1 DGN D DATA CLOCK AVEE INL1, INL2, I NL3, INL4, INL5, INL6, INL7, INL8, INL9 INR1,INR2, I NR3, INR4,INR5,I NR6, INR7,INR8,I NR9 MUTE SBRCIN,SBL CIN SUBL,SU BR ADCL, ADCR RECR3,RECL3INRA/RECR1,INLA/RECL1, INRB/REC R2,INLB/ RECL2, INR10/RECR4,I NL10/RECL4, INR11/RECR5,I NL11/RECL5

Function Output pin of FL/ FR/C/SW/SL/ SR/SBL/ SBR channel

Connects capacitor fo r reducing click no ise of L/R /C/SW/SL/SR/SBL/ SBR channel vol ume Analog groun d of intern al circuit Frequency characteristic setting pin of L/R chann el tone control (Treble) Frequency characteristic setting pin of L/R chann el tone control (Bass) Positive powe r supply to int ernal cir cuit

Input pin of L/R /C/SW/SL/ SR/SBL /SBR channel (Multi IN 1/2)

Digital ground of intern al circuit Input pin of c ontrol data Input pin of c ontrol clock Negative pow er supply to internal cir cuit

Input pin of L/R channel ( Input Selector)

Outside Mute Con trol PIN Input pin for S BL/ SBR channel Volum e Output pin for L/R chann el SUB Outpu t Output pin for L/R chann el ADC Output pin for L/R chann el RE C Output Input pin of L/R channel ( Input Selector)/ Output pin for L/R chann el RE C Output

N.C.

No Connected PIN

53 AVR-1909/789, AVC-1909

Sil9135 (IC1008)

Functional Block Diagram

54 AVR-1909/789, AVC-1909

ADV7401BSTZ (IC1020)

PIN FUNCTION DESCRIPTION

55 AVR-1909/789, AVC-1909

56 AVR-1909/789, AVC-1909

Sil9134 (IC1009)

Functional Block Diagram

57 AVR-1909/789, AVC-1909

GLT5640L32 (IC1014)Block Diagram

58 AVR-1909/789, AVC-1909

W9864G2GH (IC1022)

W9864G2GH Block Diagram

59 AVR-1909/789, AVC-1909

W9864G2GH-6 Pim Description

60 AVR-1909/789, AVC-1909

Sil9185 (IC1002)DVCC18 AVCC18 AVCC18 AVCC33 HPD1 I2CSEL/ INT DGND RPWR0 DSDA0 R1XC+ DSCL0 R0X2+ R0X1+ R0X0+ 22 R1XCAGND AGND R0X2R0X1R0X021

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

24

23

R1X0R1X0+ AVCC33 R1X1R1X1+ AGND R1X2R1X2+ AVCC18 DSDA1 DSCL1 RPWR1 CEC_D CEC_A AVCC33 HPD2 AVCC18 R2XCR2XC+ AGND

41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 5758

20 19 18 17 16 15 14 13

AGND R0XC+ R0XCAVCC18 HPD0 LSCL/ EPSEL[1] LSDA/ EPSEL[0] RESET# EXTSWING TxCTxC+ AGND Tx0Tx0+ AVCC18 Tx1Tx1+ AGND Tx2Tx2+

Sil 918580-Pin TQFP(Top View)

12 11 10 9 8 7 6 5 43

59 64 65 66 67 68 69 70 71 72 73 74 75 76 7778

2 79 61 62 63 80 1

60

Sil9185 Block DiagramPort0_DDC Port1_DDC Port2_DDC

EPSEL1/ LSCL

EPSEL0/ LSDA

TX_DDC

EDID Block Termination/ Equalizer R0X0+/R0X1+/R0X2+/R0XC+/R1X0+/R1X1+/R1X2+/R1XC+/R2X0+/R2X1+/R2X2+/R2XC+/Config Logic I2C Switch Configuration Block Oversample EDID RAM Transmitter Block TX0+/TX1+/Transmit Drivers TX2+/-

Termination/ Equalizer

Termination/ Equalizer

DPLL

TPWR/ I2CADDR AGND

TSDA

AGND

R2X0-

R2X1-

R2X0+

R2X1+

R2X2-

R2X2+

DSDA2

RPWR2

RSVDL

DGND

AVCC33

AVCC18

DSCL2

DVCC18

HPDIN

TSCL

PLL 5V Switch HPD Switch

TXC+/-

Receiver Block I2CADDR/ TPWR RPWR0 RPWR1 RPWR2 HPD0 HPD1 HPD2 HPDIN

CEC

CEC I/F

CEC_A

61 AVR-1909/789, AVC-1909

CEC_D

LC89057W (IC1027)RERR INT CKST AUDIO/VO EMPHA/UO DGND DVDD XIN XOUT XMCK DVDD DGND

LC89057W Block DiagramEMPHA/UO 32 AUDIO/VO 33 INT CL CE DI 35 40 39 38 XMODE 41

36 35 34 33 32 31 30 29 28 27 26 25

DO DI CE CL XMODE DGND DVDD TMCK/PIO0 TBCK/PIO1 TLRCK/PIO2 TDATA/PIO3 TXO/PIOEN

37 38 39 40 41 42 43 44 45 46 47 48

TOP VIEW

24 23 22 21 20 19 18 17 16 15 14 13

SDIN SLRCK SBCK RDATA RLRCK DVDD DGND RBCK RMCK AGND AVDD LPF

RXOUT 1 RX0 RX1 RX2 RX3 RX4 RX5/VI RX6/UI 2 3 4 5 8 9 10

C bit, U bit

Microcontroller I/F

37 DO 36 RERR

Input Selector

Demodulation & Lock Detect

Data Selector

21 RDATA

24 SDIN PLL Clock Selector Modulation or Parallel Port I/N 16 17 20 22 23 RMCK RBCK RLRCK SBCK SLRCK

LPF 13 TMCK/PIO0 TBCK/PIO1 TLRCK/PIO2 TDATA/PIO3 44 45 46 47

RXOUT 1 RX0 2 RX1 3 RX2 4 RX3 5 DGND 6 DVDD 7 RX4 8 RX5/VI 9 RX6/UI 10 DVDD 11 DGND 12

TXO/PIOEN 48 29 XIN 28 XOUT 27 XMCK 34 CKST

LC89057W Terminal FunctionPin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Pin Name RXOUT RX0 RX1 RX2 RX3 DGND DVDD RX4 RX5/VI RX6/UI DVDD DGND LPF AVDD AGND RMCK RBCK DGND DVDD RLRCK RDATA SBCK SLRCK SDIN DGND DVDD XMCK I/O O I I I I I I I O O O/I O/I O O O I O Function Input bi-phase select data output terminal TTL compatible digital data input terminal Coaxial compatible amp built-in digital data input terminal TTL compatible digital data input terminal TTL compatible digital data input terminal Digital GND Digital power TTL compatible digital data input terminal TTL compatible digital data/Validity flag input terminal for modulation TTL compatible digital data/User data input terminal for modulation Digital power for PLL Digital GND for PLL PLL loop filter connecting terminal Analog power for PLL Analog GND for PLL RMCK clock output terminal (256fs, 512fs, XIN, VCO) RBCK clock in/output terminal (64fs) Digital GND Digital power RLRCK clock in/output terminal (fs) Serial audio data output terminal SBCK clock output terminal (32fs, 64fs, 128fs) SLRCK clock output terminal (fs/2, fs, 2fs) Serial audio data input terminal Digital GND Digital power Osc. amp output terminal

62 AVR-1909/789, AVC-1909

Pin No. 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

Pin Name XOUT XIN DVDD DGND EMPHA/UO AUDIO/VO CKST INT RERR DO DI CE CL XMODE DGND DVDD TMCK/PIO0 TBCK/PIO1 TLRCK/PIO2 TDATA/PIO3 TXO/PIOEN

I/O O I I/O I/O I/O I/O O O I I I I I/O I/O I/O I/O O/I

Function Xtal osc. connecting output terminal Xtal osc. connection, external clock input terminal (24.576MHz or 12.288MHz) Digital power Digital GND Emphasis information/U-data output/Chip address setting terminal Non-PCM detect/V-flag output/ Chip address setting terminal Clock switch transition period output/Demodulation master or slave function switching terminal Interrupt output for com (Interrupt factor selectable)/Modulation or general I/O switching terminal PLL lock error, data error flag output com I/F, read out data output terminal (3-state) com I/F, write data input terminal com I/F, chip enable input terminal com I/F, clock input terminal System reset input terminal Digital GND Digital power 256fs system clock input for modulation/General I/O in/output terminal 64fs bit clock input for modulation/General I/O in/output terminal fs clock input for modulation/General I/O in/output terminal Serial audio data input for modulation/General I/O in/output terminal Modulation data output/ General I/O enable input terminal

* For latch-up countermeasure, perform each power supply ON/OFF in the same timing.

NJW1321 (IC2023)

Block Diagram

63 AVR-1909/789, AVC-1909

ADAU1328 (IC1026)

64 AVR-1909/789, AVC-1909

ADV7172KSTZ (IC1019)

ADV7172KSTZ Block Diagram

65 AVR-1909/789, AVC-1909

ADV7172KSTZ Pin Function Description

66 AVR-1909/789, AVC-1909

F2621E-01(IC1037 : for E3 model only)MUTE I2S_OCLK VSS I2S_LRCLK VDD44 43 42 41 40

SAII_EN SAII_DATA VDD SAII_CLK

48

47

46

45

39

38

LSDP VSS SC_TX_OUT VDD SC_RX_IN RFU (I2C_SCL) RFU (I2C_SDA) VDD ANT_REV VSS RESET# SLAVE_SEL

37

I2S_SCLK VSS I2S_DATA

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

36 35 34 33 32 31 30 29 28 27 26 25

XM/DT IC Rev 3B/4A

HSDP_EN# DT4_MODE HSDP_CLK VDD HSDP_DATA VSS TEST SC_RATE OSC_IN VDD OSC_OUT VSS

I2S_RATE LINKACTIVE COMM_TX_EN VSS VDD

VDD VSS COMM_TX_M COMM_TX_P

Function Discription

COMM_RX_P COMM_RX_M

VSS

XMDTIC

Inter-IC Sound (I2S)

I2S_OCLK (M=o, S=n/u) I2S_LRCLK (M=o; S=i) I2S_SCLK (M=o; S=i) I2S_DATA (M=o; S=i) I2S_RATE (M=o, S=n/u) MUTE (M=o, S=n/u) HSDP_EN# (M=o; S=i) HSDP_CLK (M=o; S=i) HSDP_DATA (M=o; S=i)

3.3V GND COMM_TX_P COMM_TX_M

COMM ENGINE

High Speed Data Port (HSDP)

COMM I/F

COMM_RX_P COMM_RX_M LINKACTIVE (M=o, S=o) COMM_TX_EN (M=o, S=o)

Low Speed Data Port (LSDP)

LSDP (M=o; S=i)

SAII Sys Ctrlr (CBM) Bus I/F

SAII_REQ (M=i; S=o) SAII_CLK (M=o; S=i) SAII_DATA (M=o; S=i) SC_RX_IN (M=i, S=i) SC_TX_OUT (M=o, S=o) SC_RATE (M=i, S=o) RESET# (M=i, S=i) ANT_REV (M=o, S=n/u) DT4_MODE (M=i, S=i) SLAVE_SEL (M=i, S=i) TEST (M=i, S=i) (RFU I2C_SCL) (RFU I2C_SDA)

OSC_IN

OSCOSC_OUT

RAM

Misc Status & Control

67 AVR-1909/789, AVC-1909

pPin # Pin Name DirectFunction ion in Slave Mode S=In Low Speed Data Port Input M=Out S=Out System Controller Bus (CBM) M=Out Transmit Data Out S=In System Controller Bus (CBM) M=In Receive Data In Reserved for Future Use (pull S=In down with a 100k resistor to M=In Ground) Reserved for Future Use (pull S=In down with a 100k resistor to M=In Ground) Function in Master Mode Low Speed Data Port Output Notes Out= 4mA, SLC In=LVTTL S/T 4mA, SLC LVTTL S/T LVTTL S/T

1 LSDP 3 SC_TX_OUT 5 SC_RX_IN 6 RFU (I2C-SCL)